From: Giammarco Marzano Date: Wed, 14 Sep 2022 12:20:43 +0000 (+0200) Subject: ipq40xx: Add ZTE MF289F X-Git-Tag: v22.03.3~186 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=3e15a54bb0ef470e19a36dfbbd97c1bc9b363b99;p=openwrt%2Fstaging%2Fhauke.git ipq40xx: Add ZTE MF289F It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA) and Vodafone DE\T-Mobile PL (called GigaCube). Modem is a MiniPCIe-to-USB based on Snapdragon X24, it supports 4CA aggregation. There are currently two hardware revisions, which differ on the 5Ghz radio: AT1 = QCA9984 5Ghz Radio on PCI-E bus AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz Device specification -------------------- SoC Type: Qualcomm IPQ4019 RAM: 256 MiB Flash: 128 MiB SPI NAND (Winbond W25N01GV) ROM: 2MiB SPI Flash (GD25Q16) Wireless 2.4 GHz (IP4019): b/g/n, 2x2 Wireless 5 GHz: (QCA9984): a/n/ac, 4x4 HW REV AT1 (IPA4019): a/n/ac, 2x2 HW REV AT2 Ethernet: 2xGbE (WAN/LAN1, LAN2) USB ports: No Button: 2 (Reset/WPS) LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue) Power: 12 VDC, 1 A Connector type: Barrel Bootloader: U-Boot Installation ------------ 1. Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 2. Connect serial console (115200,8n1) to serial connector GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX (refer to this image: https://ibb.co/31Gngpr). 3. Connect TFTP server to RJ-45 port (WAN/LAN1). 4. Stop in u-Boot (using ESC button) and run u-Boot commands: setenv serverip 192.168.0.2 setenv ipaddr 192.168.0.1 set fdt_high 0x85000000 tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb bootm $loadaddr 5. Please make backup of original partitions, if you think about revert to stock, specially mtd16 (Web UI) and mtd17 (rootFS). Use /tmp as temporary storage and do: WEB PARITION -------------------------------------- cat /dev/mtd16 > /tmp/mtd16.bin scp /tmp/mtd16.bin root@YOURSERVERIP:/ rm /tmp/mtd16.bin ROOT PARITION -------------------------------------- cat /dev/mtd17 > /tmp/mtd17.bin scp /tmp/mtd17.bin root@YOURSERVERIP:/ rm /tmp/mtd17.bin 6. Login via ssh or serial and remove stock partitions (default IP 192.168.0.1): # this can return an error, if ubi was attached before # or rootfs part was erased before. ubiattach -m 17 # it could return error if rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs # some devices doesn't have it ubirmvol /dev/ubi0 -N ubi_rootfs_data 7. download and install image via sysupgrade -n (either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin to the device's /tmp directory) sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin Sometimes it could print ubi attach error, but please ignore it if process goes forward. Flash Layout NAND: mtd8: 000a0000 00020000 "fota-flag" mtd9: 00080000 00020000 "0:ART" mtd10: 00080000 00020000 "mac" mtd11: 000c0000 00020000 "reserved2" mtd12: 00400000 00020000 "cfg-param" mtd13: 00400000 00020000 "log" mtd14: 000a0000 00020000 "oops" mtd15: 00500000 00020000 "reserved3" mtd16: 00800000 00020000 "web" mtd17: 01d00000 00020000 "rootfs" mtd18: 01900000 00020000 "data" mtd19: 03200000 00020000 "fota" mtd20: 0041e000 0001f000 "kernel" mtd21: 0101b000 0001f000 "ubi_rootfs" SPI: mtd0: 00040000 00010000 "0:SBL1" mtd1: 00020000 00010000 "0:MIBIB" mtd2: 00060000 00010000 "0:QSEE" mtd3: 00010000 00010000 "0:CDT" mtd4: 00010000 00010000 "0:DDRPARAMS" mtd5: 00010000 00010000 "0:APPSBLENV" mtd6: 000c0000 00010000 "0:APPSBL" mtd7: 00050000 00010000 "0:reserved1" Back to Stock (!!! need original dump taken from initramfs !!!) ------------- 1. Place mtd16.bin and mtd17.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 2. Connect serial console (115200,8n1) to serial console connector (refer to the pin-out from above). 3. Connect TFTP server to RJ-45 port (WAN/LAN1). 4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s 5. Stop in u-Boot (using ESC button) and run u-Boot commands: This will erase RootFS+Web: nand erase 0x1000000 0x800000 nand erase 0x1800000 0x1D00000 This will restore RootFS: tftpboot 0x84000000 ${dir}root_uImage_s nand erase 0x1800000 0x1D00000 nand write $fileaddr 0x1800000 $filesize This will restore Web Interface: tftpboot 0x84000000 ${dir}web.img nand erase 0x1000000 0x800000 nand write $fileaddr 0x1000000 $filesize After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router Signed-off-by: Giammarco Marzano Reviewed-by: Lech Perczak (Warning: commit message did not conform to UTF-8 - hopefully fixed?, added description of the pin-out if image goes down, reformatted commit message to be hopefully somewhat readable on git-web, redid some of the gpio-buttons & leds DT nodes, etc.) Signed-off-by: Christian Lamparter (cherry picked from commit 0de6a3339f1aadc1de2c9371435e3de239a00645) [Backported to 22.03: added DTS to the makefile patch, fixed ipq-wifi inclusion for MF286D] Signed-off-by: Lech Perczak --- diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index 496d564baf..be9b547cd0 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -54,7 +54,8 @@ ALLWIFIBOARDS:= \ qxwlan_e2600ac-c1 \ qxwlan_e2600ac-c2 \ teltonika_rutx \ - zte_mf286d + zte_mf286d \ + zte_mf289f ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD)) @@ -145,5 +146,6 @@ $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac-c1,Qxwlan E2600AC C1)) $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac-c2,Qxwlan E2600AC C2)) $(eval $(call generate-ipq-wifi-package,teltonika_rutx,Teltonika RUTX)) $(eval $(call generate-ipq-wifi-package,zte_mf286d,ZTE MF286D)) +$(eval $(call generate-ipq-wifi-package,zte_mf289f,ZTE MF289F)) $(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE)))) diff --git a/package/firmware/ipq-wifi/board-zte_mf289f.qca4019 b/package/firmware/ipq-wifi/board-zte_mf289f.qca4019 new file mode 100644 index 0000000000..3a4cb8b888 Binary files /dev/null and b/package/firmware/ipq-wifi/board-zte_mf289f.qca4019 differ diff --git a/package/firmware/ipq-wifi/board-zte_mf289f.qca9984 b/package/firmware/ipq-wifi/board-zte_mf289f.qca9984 new file mode 100644 index 0000000000..0422bc852f Binary files /dev/null and b/package/firmware/ipq-wifi/board-zte_mf289f.qca9984 differ diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 2aa4886e6a..deb9ec64f6 100644 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -150,6 +150,11 @@ ipq40xx_setup_interfaces() ucidef_add_switch "switch0" \ "0u@eth0" "2:lan:4" "3:lan:3" "4:lan:2" "0u@eth1" "5:wan" ;; + zte,mf289f) + ucidef_set_interfaces_lan_wan "eth0" "eth1" + ucidef_add_switch "switch0" \ + "0u@eth0" "0u@eth1" "2:lan:1" "5:lan:2" + ;; *) echo "Unsupported hardware. Network interfaces not initialized" ;; diff --git a/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches b/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches index a52a33d2f4..b5c96da962 100644 --- a/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches +++ b/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches @@ -24,7 +24,8 @@ mikrotik,cap-ac) mikrotik,hap-ac3) ucidef_add_gpio_switch "poe_passtrough" "PoE Passthrough" "452" "0" ;; -zte,mf286d) +zte,mf286d|\ +zte,mf289f) ucidef_add_gpio_switch "power_btn_block" "Power button blocker" "421" "0" ;; esac diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index e8c94409a7..e9c17e5b01 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -25,7 +25,8 @@ Once this is done. Retry. EOF return 1 ;; - zte,mf286d) + zte,mf286d |\ + zte,mf289f) CI_UBIPART="rootfs" local mtdnum="$( find_mtd_index $CI_UBIPART )" [ ! "$mtdnum" ] && return 1 @@ -185,7 +186,8 @@ platform_do_upgrade() { platform_do_upgrade_dualboot_datachk "$1" ;; teltonika,rutx10 |\ - zte,mf286d) + zte,mf286d |\ + zte,mf289f) CI_UBIPART="rootfs" nand_do_upgrade "$1" ;; diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-mf289f.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-mf289f.dts new file mode 100644 index 0000000000..2dac307990 --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-mf289f.dts @@ -0,0 +1,438 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +// Copyright (c) 2022, Pawel Dembicki . +// Copyright (c) 2022, Giammarco Marzano . + +#include "qcom-ipq4019.dtsi" +#include +#include +#include +#include + +/ { + model = "ZTE MF289F"; + compatible = "zte,mf289f"; + + aliases { + led-boot = &led_status; + led-failsafe = &led_status; + led-running = &led_status; + led-upgrade = &led_status; + }; + + chosen { + /* + * bootargs forced by u-boot bootipq command: + * 'ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait' + */ + bootargs-append = " root=/dev/ubiblock0_1"; + }; + + /* + * This node is used to restart modem module to avoid anomalous + * behaviours on initial communication. + */ + gpio-restart { + compatible = "gpio-restart"; + gpios = <&tlmm 8 GPIO_ACTIVE_HIGH>; + }; + + leds { + compatible = "gpio-leds"; + + led_status: led-0 { + label = "blue:power"; + function = LED_FUNCTION_POWER; + color = ; + gpios = <&tlmm 10 GPIO_ACTIVE_LOW>; + }; + + led-1 { + function = LED_FUNCTION_WLAN; + color = ; + gpios = <&tlmm 61 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + }; + + keys { + compatible = "gpio-keys"; + + key-reset { + label = "reset"; + linux,code = ; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + }; + + key-wps { + label = "wps"; + linux,code = ; + gpios = <&tlmm 68 GPIO_ACTIVE_LOW>; + }; + }; + + soc { + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + /* select hostmode */ + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + status = "okay"; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + }; +}; + +&prng { + status = "okay"; +}; + +&mdio { + status = "okay"; + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + reset-gpios = <&tlmm 47 GPIO_ACTIVE_LOW>; + reset-delay-us = <2000>; +}; + +&watchdog { + status = "okay"; +}; + +&blsp_dma { + status = "okay"; +}; + +&usb2 { + status = "okay"; +}; + +&usb3 { + status = "okay"; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>, + <&tlmm 54 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:SBL1"; + reg = <0x0 0x40000>; + read-only; + }; + + partition@40000 { + label = "0:MIBIB"; + reg = <0x40000 0x20000>; + read-only; + }; + + partition@60000 { + label = "0:QSEE"; + reg = <0x60000 0x60000>; + read-only; + }; + + partition@c0000 { + label = "0:CDT"; + reg = <0xc0000 0x10000>; + read-only; + }; + + partition@d0000 { + label = "0:DDRPARAMS"; + reg = <0xd0000 0x10000>; + read-only; + }; + + partition@e0000 { + label = "0:APPSBLENV"; + reg = <0xe0000 0x10000>; + read-only; + }; + + partition@f0000 { + label = "0:APPSBL"; + reg = <0xf0000 0xc0000>; + read-only; + }; + + partition@1b0000 { + label = "0:reserved1"; + reg = <0x1b0000 0x50000>; + read-only; + }; + }; + }; + + spi-nand@1 { /* flash@1 ? */ + compatible = "spi-nand"; + reg = <1>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "fota-flag"; + reg = <0x0 0xa0000>; + read-only; + }; + + partition@a0000 { + label = "ART"; + reg = <0xa0000 0x80000>; + read-only; + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + precal_art_1000: precal@1000 { + reg = <0x1000 0x2f20>; + }; + + precal_art_5000: precal@5000 { + reg = <0x5000 0x2f20>; + }; + }; + + partition@120000 { + label = "mac"; + reg = <0x120000 0x80000>; + read-only; + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_mac_0: macaddr@0 { + reg = <0x0 0x6>; + }; + }; + + partition@1a0000 { + label = "reserved2"; + reg = <0x1a0000 0xc0000>; + read-only; + }; + + partition@260000 { + label = "cfg-param"; + reg = <0x260000 0x400000>; + read-only; + }; + + partition@660000 { + label = "log"; + reg = <0x660000 0x400000>; + }; + + partition@a60000 { + label = "oops"; + reg = <0xa60000 0xa0000>; + }; + + partition@b00000 { + label = "reserved3"; + reg = <0xb00000 0x500000>; + read-only; + }; + + partition@1000000 { + label = "web"; + reg = <0x1000000 0x800000>; + }; + + partition@1800000 { + label = "rootfs"; + reg = <0x1800000 0x1d00000>; + }; + + partition@3500000 { + label = "data"; + reg = <0x3500000 0x1900000>; + }; + + partition@4e00000 { + label = "fota"; + reg = <0x4e00000 0x3200000>; + }; + }; + }; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&crypto { + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&gmac0 { + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_mac_0>; +}; + +&gmac1 { + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_mac_0>; + mac-address-increment = <1>; +}; + + +&qpic_bam { + status = "okay"; +}; + +&tlmm { + i2c_0_pins: i2c_0_pinmux { + mux { + pins = "gpio20", "gpio21"; + function = "blsp_i2c0"; + bias-disable; + }; + }; + + mdio_pins: mdio_pinmux { + mux_1 { + pins = "gpio6"; + function = "mdio"; + bias-pull-up; + }; + + mux_2 { + pins = "gpio7"; + function = "mdc"; + bias-pull-up; + }; + }; + + serial_pins: serial_pinmux { + mux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio13", "gpio14", "gpio15"; + drive-strength = <12>; + bias-disable; + }; + + pinmux_cs { + function = "gpio"; + pins = "gpio12", "gpio54"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + nvmem-cell-names = "pre-calibration", "mac-address"; + nvmem-cells = <&precal_art_1000>, <&macaddr_mac_0>; + mac-address-increment = <2>; + qcom,ath10k-calibration-variant = "zte,mf289f"; +}; + +/* This node is used only on AT2 version for 5Ghz on IPQ4019 with board-id=21 */ +&wifi1 { + status = "okay"; + nvmem-cell-names = "pre-calibration", "mac-address"; + nvmem-cells = <&precal_art_5000>, <&macaddr_mac_0>; + mac-address-increment = <3>; + qcom,ath10k-calibration-variant = "zte,mf289f"; +}; + +/* This node is used only on AT1 version for 5Ghz on QCA9984 */ +&pcie0 { + status = "okay"; + perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 40 GPIO_ACTIVE_LOW>; + clkreq-gpio = <&tlmm 39 GPIO_ACTIVE_LOW>; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi2: wifi@1,0 { + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_mac_0>; + mac-address-increment = <4>; + compatible = "qcom,ath10k"; + reg = <0x00010000 0 0 0 0>; + qcom,ath10k-calibration-variant = "zte,mf289f"; + }; + }; +}; diff --git a/target/linux/ipq40xx/image/generic.mk b/target/linux/ipq40xx/image/generic.mk index cf89409b17..e02527e108 100644 --- a/target/linux/ipq40xx/image/generic.mk +++ b/target/linux/ipq40xx/image/generic.mk @@ -994,19 +994,31 @@ define Device/unielec_u4019-32m endef TARGET_DEVICES += unielec_u4019-32m -define Device/zte_mf286d +define Device/zte_mf28x_common $(call Device/FitzImage) DEVICE_VENDOR := ZTE - DEVICE_MODEL := MF286D SOC := qcom-ipq4019 DEVICE_DTS_CONFIG := config@ap.dk04.1-c1 BLOCKSIZE := 128k PAGESIZE := 2048 KERNEL_IN_UBI := 1 - DEVICE_PACKAGES := ipq-wifi-zte_mf286d kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi + DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi +endef + +define Device/zte_mf286d + $(call Device/zte_mf28x_common) + DEVICE_MODEL := MF286D + DEVICE_PACKAGES := ipq-wifi-zte_mf286d endef TARGET_DEVICES += zte_mf286d +define Device/zte_mf289f + $(call Device/zte_mf28x_common) + DEVICE_MODEL := MF289F + DEVICE_PACKAGES += ipq-wifi-zte_mf289f ath10k-firmware-qca9984-ct +endef +TARGET_DEVICES += zte_mf289f + define Device/zyxel_nbg6617 $(call Device/FitImageLzma) DEVICE_VENDOR := ZyXEL diff --git a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch index 4fc0566c73..c51586a232 100644 --- a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -904,11 +904,75 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -904,11 +904,76 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -61,6 +61,7 @@ Signed-off-by: John Crispin + qcom-ipq4019-map-ac2200.dtb \ + qcom-ipq4019-lhgg-60ad.dtb \ + qcom-ipq4019-mf286d.dtb \ ++ qcom-ipq4019-mf289f.dtb \ + qcom-ipq4019-mr8300.dtb \ + qcom-ipq4019-pa2200.dtb \ + qcom-ipq4019-r619ac-64m.dtb \