From: Francois Romieu Date: Sat, 10 Mar 2012 10:50:03 +0000 (+0100) Subject: uli526x: stop using net_device.{base_addr, irq} and convert to __iomem. X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=3acf4b5cde8123a7a243d9dcd63f3e6990c8e5bb;p=openwrt%2Fstaging%2Fblogic.git uli526x: stop using net_device.{base_addr, irq} and convert to __iomem. The bulk of the patch comes from the __iomem changes. - the phy read and write operations were carrying the chip id deep down the call chain. Let's waste a pointer and contain the flying spaghetti monster. - phy_{read, write}_1bit only need to access the DCR9 register. The loss of generality here should not hurt. - removed a leftover printk of the EISA era. This is a pure PCI device. Signed-off-by: Francois Romieu Acked-by: Grant Grundler --- diff --git a/drivers/net/ethernet/dec/tulip/uli526x.c b/drivers/net/ethernet/dec/tulip/uli526x.c index c9b33961826c..75d45f8a37dc 100644 --- a/drivers/net/ethernet/dec/tulip/uli526x.c +++ b/drivers/net/ethernet/dec/tulip/uli526x.c @@ -42,6 +42,8 @@ #include #include +#define uw32(reg, val) iowrite32(val, ioaddr + (reg)) +#define ur32(reg) ioread32(ioaddr + (reg)) /* Board/System/Debug information/definition ---------------- */ #define PCI_ULI5261_ID 0x526110B9 /* ULi M5261 ID*/ @@ -110,14 +112,6 @@ do { \ #define SROM_V41_CODE 0x14 -#define SROM_CLK_WRITE(data, ioaddr) \ - outl(data|CR9_SROM_READ|CR9_SRCS,ioaddr); \ - udelay(5); \ - outl(data|CR9_SROM_READ|CR9_SRCS|CR9_SRCLK,ioaddr); \ - udelay(5); \ - outl(data|CR9_SROM_READ|CR9_SRCS,ioaddr); \ - udelay(5); - /* Structure/enum declaration ------------------------------- */ struct tx_desc { __le32 tdes0, tdes1, tdes2, tdes3; /* Data for the card */ @@ -132,12 +126,15 @@ struct rx_desc { } __attribute__(( aligned(32) )); struct uli526x_board_info { - u32 chip_id; /* Chip vendor/Device ID */ + struct uli_phy_ops { + void (*write)(struct uli526x_board_info *, u8, u8, u16); + u16 (*read)(struct uli526x_board_info *, u8, u8); + } phy; struct net_device *next_dev; /* next device */ struct pci_dev *pdev; /* PCI device */ spinlock_t lock; - long ioaddr; /* I/O base address */ + void __iomem *ioaddr; /* I/O base address */ u32 cr0_data; u32 cr5_data; u32 cr6_data; @@ -227,21 +224,21 @@ static netdev_tx_t uli526x_start_xmit(struct sk_buff *, static int uli526x_stop(struct net_device *); static void uli526x_set_filter_mode(struct net_device *); static const struct ethtool_ops netdev_ethtool_ops; -static u16 read_srom_word(long, int); +static u16 read_srom_word(struct uli526x_board_info *, int); static irqreturn_t uli526x_interrupt(int, void *); #ifdef CONFIG_NET_POLL_CONTROLLER static void uli526x_poll(struct net_device *dev); #endif -static void uli526x_descriptor_init(struct net_device *, unsigned long); +static void uli526x_descriptor_init(struct net_device *, void __iomem *); static void allocate_rx_buffer(struct net_device *); -static void update_cr6(u32, unsigned long); +static void update_cr6(u32, void __iomem *); static void send_filter_frame(struct net_device *, int); -static u16 phy_read(unsigned long, u8, u8, u32); -static u16 phy_readby_cr10(unsigned long, u8, u8); -static void phy_write(unsigned long, u8, u8, u16, u32); -static void phy_writeby_cr10(unsigned long, u8, u8, u16); -static void phy_write_1bit(unsigned long, u32, u32); -static u16 phy_read_1bit(unsigned long, u32); +static u16 phy_readby_cr9(struct uli526x_board_info *, u8, u8); +static u16 phy_readby_cr10(struct uli526x_board_info *, u8, u8); +static void phy_writeby_cr9(struct uli526x_board_info *, u8, u8, u16); +static void phy_writeby_cr10(struct uli526x_board_info *, u8, u8, u16); +static void phy_write_1bit(struct uli526x_board_info *db, u32); +static u16 phy_read_1bit(struct uli526x_board_info *db); static u8 uli526x_sense_speed(struct uli526x_board_info *); static void uli526x_process_mode(struct uli526x_board_info *); static void uli526x_timer(unsigned long); @@ -253,6 +250,18 @@ static void uli526x_free_rxbuffer(struct uli526x_board_info *); static void uli526x_init(struct net_device *); static void uli526x_set_phyxcer(struct uli526x_board_info *); +static void srom_clk_write(struct uli526x_board_info *db, u32 data) +{ + void __iomem *ioaddr = db->ioaddr; + + uw32(DCR9, data | CR9_SROM_READ | CR9_SRCS); + udelay(5); + uw32(DCR9, data | CR9_SROM_READ | CR9_SRCS | CR9_SRCLK); + udelay(5); + uw32(DCR9, data | CR9_SROM_READ | CR9_SRCS); + udelay(5); +} + /* ULI526X network board routine ---------------------------- */ static const struct net_device_ops netdev_ops = { @@ -277,6 +286,7 @@ static int __devinit uli526x_init_one (struct pci_dev *pdev, { struct uli526x_board_info *db; /* board information structure */ struct net_device *dev; + void __iomem *ioaddr; int i, err; ULI526X_DBUG(0, "uli526x_init_one()", 0); @@ -338,14 +348,26 @@ static int __devinit uli526x_init_one (struct pci_dev *pdev, db->buf_pool_start = db->buf_pool_ptr; db->buf_pool_dma_start = db->buf_pool_dma_ptr; - db->chip_id = ent->driver_data; - db->ioaddr = pci_resource_start(pdev, 0); + switch (ent->driver_data) { + case PCI_ULI5263_ID: + db->phy.write = phy_writeby_cr10; + db->phy.read = phy_readby_cr10; + break; + default: + db->phy.write = phy_writeby_cr9; + db->phy.read = phy_readby_cr9; + break; + } + /* IO region. */ + ioaddr = pci_iomap(pdev, 0, 0); + if (!ioaddr) + goto err_out_free_tx_buf; + + db->ioaddr = ioaddr; db->pdev = pdev; db->init = 1; - dev->base_addr = db->ioaddr; - dev->irq = pdev->irq; pci_set_drvdata(pdev, dev); /* Register some necessary functions */ @@ -357,24 +379,24 @@ static int __devinit uli526x_init_one (struct pci_dev *pdev, /* read 64 word srom data */ for (i = 0; i < 64; i++) - ((__le16 *) db->srom)[i] = cpu_to_le16(read_srom_word(db->ioaddr, i)); + ((__le16 *) db->srom)[i] = cpu_to_le16(read_srom_word(db, i)); /* Set Node address */ if(((u16 *) db->srom)[0] == 0xffff || ((u16 *) db->srom)[0] == 0) /* SROM absent, so read MAC address from ID Table */ { - outl(0x10000, db->ioaddr + DCR0); //Diagnosis mode - outl(0x1c0, db->ioaddr + DCR13); //Reset dianostic pointer port - outl(0, db->ioaddr + DCR14); //Clear reset port - outl(0x10, db->ioaddr + DCR14); //Reset ID Table pointer - outl(0, db->ioaddr + DCR14); //Clear reset port - outl(0, db->ioaddr + DCR13); //Clear CR13 - outl(0x1b0, db->ioaddr + DCR13); //Select ID Table access port + uw32(DCR0, 0x10000); //Diagnosis mode + uw32(DCR13, 0x1c0); //Reset dianostic pointer port + uw32(DCR14, 0); //Clear reset port + uw32(DCR14, 0x10); //Reset ID Table pointer + uw32(DCR14, 0); //Clear reset port + uw32(DCR13, 0); //Clear CR13 + uw32(DCR13, 0x1b0); //Select ID Table access port //Read MAC address from CR14 for (i = 0; i < 6; i++) - dev->dev_addr[i] = inl(db->ioaddr + DCR14); + dev->dev_addr[i] = ur32(DCR14); //Read end - outl(0, db->ioaddr + DCR13); //Clear CR13 - outl(0, db->ioaddr + DCR0); //Clear CR0 + uw32(DCR13, 0); //Clear CR13 + uw32(DCR0, 0); //Clear CR0 udelay(10); } else /*Exist SROM*/ @@ -384,16 +406,18 @@ static int __devinit uli526x_init_one (struct pci_dev *pdev, } err = register_netdev (dev); if (err) - goto err_out_free_tx_buf; + goto err_out_unmap; netdev_info(dev, "ULi M%04lx at pci%s, %pM, irq %d\n", ent->driver_data >> 16, pci_name(pdev), - dev->dev_addr, dev->irq); + dev->dev_addr, pdev->irq); pci_set_master(pdev); return 0; +err_out_unmap: + pci_iounmap(pdev, db->ioaddr); err_out_free_tx_buf: pci_free_consistent(pdev, TX_BUF_ALLOC * TX_DESC_CNT + 4, db->buf_pool_ptr, db->buf_pool_dma_ptr); @@ -418,6 +442,7 @@ static void __devexit uli526x_remove_one (struct pci_dev *pdev) struct uli526x_board_info *db = netdev_priv(dev); unregister_netdev(dev); + pci_iounmap(pdev, db->ioaddr); pci_free_consistent(db->pdev, sizeof(struct tx_desc) * DESC_ALL_CNT + 0x20, db->desc_pool_ptr, db->desc_pool_dma_ptr); @@ -460,7 +485,8 @@ static int uli526x_open(struct net_device *dev) /* Initialize ULI526X board */ uli526x_init(dev); - ret = request_irq(dev->irq, uli526x_interrupt, IRQF_SHARED, dev->name, dev); + ret = request_irq(db->pdev->irq, uli526x_interrupt, IRQF_SHARED, + dev->name, dev); if (ret) return ret; @@ -488,57 +514,57 @@ static int uli526x_open(struct net_device *dev) static void uli526x_init(struct net_device *dev) { struct uli526x_board_info *db = netdev_priv(dev); - unsigned long ioaddr = db->ioaddr; + struct uli_phy_ops *phy = &db->phy; + void __iomem *ioaddr = db->ioaddr; u8 phy_tmp; u8 timeout; - u16 phy_value; u16 phy_reg_reset; ULI526X_DBUG(0, "uli526x_init()", 0); /* Reset M526x MAC controller */ - outl(ULI526X_RESET, ioaddr + DCR0); /* RESET MAC */ + uw32(DCR0, ULI526X_RESET); /* RESET MAC */ udelay(100); - outl(db->cr0_data, ioaddr + DCR0); + uw32(DCR0, db->cr0_data); udelay(5); /* Phy addr : In some boards,M5261/M5263 phy address != 1 */ db->phy_addr = 1; - for(phy_tmp=0;phy_tmp<32;phy_tmp++) - { - phy_value=phy_read(db->ioaddr,phy_tmp,3,db->chip_id);//peer add - if(phy_value != 0xffff&&phy_value!=0) - { + for (phy_tmp = 0; phy_tmp < 32; phy_tmp++) { + u16 phy_value; + + phy_value = phy->read(db, phy_tmp, 3); //peer add + if (phy_value != 0xffff && phy_value != 0) { db->phy_addr = phy_tmp; break; } } - if(phy_tmp == 32) + + if (phy_tmp == 32) pr_warn("Can not find the phy address!!!\n"); /* Parser SROM and media mode */ db->media_mode = uli526x_media_mode; /* phyxcer capability setting */ - phy_reg_reset = phy_read(db->ioaddr, db->phy_addr, 0, db->chip_id); + phy_reg_reset = phy->read(db, db->phy_addr, 0); phy_reg_reset = (phy_reg_reset | 0x8000); - phy_write(db->ioaddr, db->phy_addr, 0, phy_reg_reset, db->chip_id); + phy->write(db, db->phy_addr, 0, phy_reg_reset); /* See IEEE 802.3-2002.pdf (Section 2, Chapter "22.2.4 Management * functions") or phy data sheet for details on phy reset */ udelay(500); timeout = 10; - while (timeout-- && - phy_read(db->ioaddr, db->phy_addr, 0, db->chip_id) & 0x8000) - udelay(100); + while (timeout-- && phy->read(db, db->phy_addr, 0) & 0x8000) + udelay(100); /* Process Phyxcer Media Mode */ uli526x_set_phyxcer(db); /* Media Mode Process */ if ( !(db->media_mode & ULI526X_AUTO) ) - db->op_mode = db->media_mode; /* Force Mode */ + db->op_mode = db->media_mode; /* Force Mode */ /* Initialize Transmit/Receive decriptor and CR3/4 */ uli526x_descriptor_init(dev, ioaddr); @@ -551,10 +577,10 @@ static void uli526x_init(struct net_device *dev) /* Init CR7, interrupt active bit */ db->cr7_data = CR7_DEFAULT; - outl(db->cr7_data, ioaddr + DCR7); + uw32(DCR7, db->cr7_data); /* Init CR15, Tx jabber and Rx watchdog timer */ - outl(db->cr15_data, ioaddr + DCR15); + uw32(DCR15, db->cr15_data); /* Enable ULI526X Tx/Rx function */ db->cr6_data |= CR6_RXSC | CR6_TXSC; @@ -571,6 +597,7 @@ static netdev_tx_t uli526x_start_xmit(struct sk_buff *skb, struct net_device *dev) { struct uli526x_board_info *db = netdev_priv(dev); + void __iomem *ioaddr = db->ioaddr; struct tx_desc *txptr; unsigned long flags; @@ -596,7 +623,7 @@ static netdev_tx_t uli526x_start_xmit(struct sk_buff *skb, } /* Disable NIC interrupt */ - outl(0, dev->base_addr + DCR7); + uw32(DCR7, 0); /* transmit this packet */ txptr = db->tx_insert_ptr; @@ -607,10 +634,10 @@ static netdev_tx_t uli526x_start_xmit(struct sk_buff *skb, db->tx_insert_ptr = txptr->next_tx_desc; /* Transmit Packet Process */ - if ( (db->tx_packet_cnt < TX_DESC_CNT) ) { + if (db->tx_packet_cnt < TX_DESC_CNT) { txptr->tdes0 = cpu_to_le32(0x80000000); /* Set owner bit */ db->tx_packet_cnt++; /* Ready to send */ - outl(0x1, dev->base_addr + DCR1); /* Issue Tx polling */ + uw32(DCR1, 0x1); /* Issue Tx polling */ dev->trans_start = jiffies; /* saved time stamp */ } @@ -620,7 +647,7 @@ static netdev_tx_t uli526x_start_xmit(struct sk_buff *skb, /* Restore CR7 to enable interrupt */ spin_unlock_irqrestore(&db->lock, flags); - outl(db->cr7_data, dev->base_addr + DCR7); + uw32(DCR7, db->cr7_data); /* free this SKB */ dev_kfree_skb(skb); @@ -637,9 +664,7 @@ static netdev_tx_t uli526x_start_xmit(struct sk_buff *skb, static int uli526x_stop(struct net_device *dev) { struct uli526x_board_info *db = netdev_priv(dev); - unsigned long ioaddr = dev->base_addr; - - ULI526X_DBUG(0, "uli526x_stop", 0); + void __iomem *ioaddr = db->ioaddr; /* disable system */ netif_stop_queue(dev); @@ -648,12 +673,12 @@ static int uli526x_stop(struct net_device *dev) del_timer_sync(&db->timer); /* Reset & stop ULI526X board */ - outl(ULI526X_RESET, ioaddr + DCR0); + uw32(DCR0, ULI526X_RESET); udelay(5); - phy_write(db->ioaddr, db->phy_addr, 0, 0x8000, db->chip_id); + db->phy.write(db, db->phy_addr, 0, 0x8000); /* free interrupt */ - free_irq(dev->irq, dev); + free_irq(db->pdev->irq, dev); /* free allocated rx buffer */ uli526x_free_rxbuffer(db); @@ -671,18 +696,18 @@ static irqreturn_t uli526x_interrupt(int irq, void *dev_id) { struct net_device *dev = dev_id; struct uli526x_board_info *db = netdev_priv(dev); - unsigned long ioaddr = dev->base_addr; + void __iomem *ioaddr = db->ioaddr; unsigned long flags; spin_lock_irqsave(&db->lock, flags); - outl(0, ioaddr + DCR7); + uw32(DCR7, 0); /* Got ULI526X status */ - db->cr5_data = inl(ioaddr + DCR5); - outl(db->cr5_data, ioaddr + DCR5); + db->cr5_data = ur32(DCR5); + uw32(DCR5, db->cr5_data); if ( !(db->cr5_data & 0x180c1) ) { /* Restore CR7 to enable interrupt mask */ - outl(db->cr7_data, ioaddr + DCR7); + uw32(DCR7, db->cr7_data); spin_unlock_irqrestore(&db->lock, flags); return IRQ_HANDLED; } @@ -710,7 +735,7 @@ static irqreturn_t uli526x_interrupt(int irq, void *dev_id) uli526x_free_tx_pkt(dev, db); /* Restore CR7 to enable interrupt mask */ - outl(db->cr7_data, ioaddr + DCR7); + uw32(DCR7, db->cr7_data); spin_unlock_irqrestore(&db->lock, flags); return IRQ_HANDLED; @@ -719,8 +744,10 @@ static irqreturn_t uli526x_interrupt(int irq, void *dev_id) #ifdef CONFIG_NET_POLL_CONTROLLER static void uli526x_poll(struct net_device *dev) { + struct uli526x_board_info *db = netdev_priv(dev); + /* ISR grabs the irqsave lock, so this should be safe */ - uli526x_interrupt(dev->irq, dev); + uli526x_interrupt(db->pdev->irq, dev); } #endif @@ -954,12 +981,7 @@ static void netdev_get_drvinfo(struct net_device *dev, strlcpy(info->driver, DRV_NAME, sizeof(info->driver)); strlcpy(info->version, DRV_VERSION, sizeof(info->version)); - if (np->pdev) - strlcpy(info->bus_info, pci_name(np->pdev), - sizeof(info->bus_info)); - else - sprintf(info->bus_info, "EISA 0x%lx %d", - dev->base_addr, dev->irq); + strlcpy(info->bus_info, pci_name(np->pdev), sizeof(info->bus_info)); } static int netdev_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) { @@ -999,18 +1021,20 @@ static const struct ethtool_ops netdev_ethtool_ops = { static void uli526x_timer(unsigned long data) { - u32 tmp_cr8; - unsigned char tmp_cr12=0; struct net_device *dev = (struct net_device *) data; struct uli526x_board_info *db = netdev_priv(dev); + struct uli_phy_ops *phy = &db->phy; + void __iomem *ioaddr = db->ioaddr; unsigned long flags; + u8 tmp_cr12 = 0; + u32 tmp_cr8; //ULI526X_DBUG(0, "uli526x_timer()", 0); spin_lock_irqsave(&db->lock, flags); /* Dynamic reset ULI526X : system error or transmit time-out */ - tmp_cr8 = inl(db->ioaddr + DCR8); + tmp_cr8 = ur32(DCR8); if ( (db->interval_rx_cnt==0) && (tmp_cr8) ) { db->reset_cr8++; db->wait_reset = 1; @@ -1020,7 +1044,7 @@ static void uli526x_timer(unsigned long data) /* TX polling kick monitor */ if ( db->tx_packet_cnt && time_after(jiffies, dev_trans_start(dev) + ULI526X_TX_KICK) ) { - outl(0x1, dev->base_addr + DCR1); // Tx polling again + uw32(DCR1, 0x1); // Tx polling again // TX Timeout if ( time_after(jiffies, dev_trans_start(dev) + ULI526X_TX_TIMEOUT) ) { @@ -1041,7 +1065,7 @@ static void uli526x_timer(unsigned long data) } /* Link status check, Dynamic media type change */ - if((phy_read(db->ioaddr, db->phy_addr, 5, db->chip_id) & 0x01e0)!=0) + if ((phy->read(db, db->phy_addr, 5) & 0x01e0)!=0) tmp_cr12 = 3; if ( !(tmp_cr12 & 0x3) && !db->link_failed ) { @@ -1054,7 +1078,7 @@ static void uli526x_timer(unsigned long data) /* For Force 10/100M Half/Full mode: Enable Auto-Nego mode */ /* AUTO don't need */ if ( !(db->media_mode & 0x8) ) - phy_write(db->ioaddr, db->phy_addr, 0, 0x1000, db->chip_id); + phy->write(db, db->phy_addr, 0, 0x1000); /* AUTO mode, if INT phyxcer link failed, select EXT device */ if (db->media_mode & ULI526X_AUTO) { @@ -1111,12 +1135,13 @@ static void uli526x_timer(unsigned long data) static void uli526x_reset_prepare(struct net_device *dev) { struct uli526x_board_info *db = netdev_priv(dev); + void __iomem *ioaddr = db->ioaddr; /* Sopt MAC controller */ db->cr6_data &= ~(CR6_RXSC | CR6_TXSC); /* Disable Tx/Rx */ - update_cr6(db->cr6_data, dev->base_addr); - outl(0, dev->base_addr + DCR7); /* Disable Interrupt */ - outl(inl(dev->base_addr + DCR5), dev->base_addr + DCR5); + update_cr6(db->cr6_data, ioaddr); + uw32(DCR7, 0); /* Disable Interrupt */ + uw32(DCR5, ur32(DCR5)); /* Disable upper layer interface */ netif_stop_queue(dev); @@ -1281,7 +1306,7 @@ static void uli526x_reuse_skb(struct uli526x_board_info *db, struct sk_buff * sk * Using Chain structure, and allocate Tx/Rx buffer */ -static void uli526x_descriptor_init(struct net_device *dev, unsigned long ioaddr) +static void uli526x_descriptor_init(struct net_device *dev, void __iomem *ioaddr) { struct uli526x_board_info *db = netdev_priv(dev); struct tx_desc *tmp_tx; @@ -1296,14 +1321,14 @@ static void uli526x_descriptor_init(struct net_device *dev, unsigned long ioaddr /* tx descriptor start pointer */ db->tx_insert_ptr = db->first_tx_desc; db->tx_remove_ptr = db->first_tx_desc; - outl(db->first_tx_desc_dma, ioaddr + DCR4); /* TX DESC address */ + uw32(DCR4, db->first_tx_desc_dma); /* TX DESC address */ /* rx descriptor start pointer */ db->first_rx_desc = (void *)db->first_tx_desc + sizeof(struct tx_desc) * TX_DESC_CNT; db->first_rx_desc_dma = db->first_tx_desc_dma + sizeof(struct tx_desc) * TX_DESC_CNT; db->rx_insert_ptr = db->first_rx_desc; db->rx_ready_ptr = db->first_rx_desc; - outl(db->first_rx_desc_dma, ioaddr + DCR3); /* RX DESC address */ + uw32(DCR3, db->first_rx_desc_dma); /* RX DESC address */ /* Init Transmit chain */ tmp_buf = db->buf_pool_start; @@ -1344,11 +1369,9 @@ static void uli526x_descriptor_init(struct net_device *dev, unsigned long ioaddr * Update CR6 value * Firstly stop ULI526X, then written value and start */ - -static void update_cr6(u32 cr6_data, unsigned long ioaddr) +static void update_cr6(u32 cr6_data, void __iomem *ioaddr) { - - outl(cr6_data, ioaddr + DCR6); + uw32(DCR6, cr6_data); udelay(5); } @@ -1367,6 +1390,7 @@ static void update_cr6(u32 cr6_data, unsigned long ioaddr) static void send_filter_frame(struct net_device *dev, int mc_cnt) { struct uli526x_board_info *db = netdev_priv(dev); + void __iomem *ioaddr = db->ioaddr; struct netdev_hw_addr *ha; struct tx_desc *txptr; u16 * addrptr; @@ -1412,9 +1436,9 @@ static void send_filter_frame(struct net_device *dev, int mc_cnt) /* Resource Empty */ db->tx_packet_cnt++; txptr->tdes0 = cpu_to_le32(0x80000000); - update_cr6(db->cr6_data | 0x2000, dev->base_addr); - outl(0x1, dev->base_addr + DCR1); /* Issue Tx polling */ - update_cr6(db->cr6_data, dev->base_addr); + update_cr6(db->cr6_data | 0x2000, ioaddr); + uw32(DCR1, 0x1); /* Issue Tx polling */ + update_cr6(db->cr6_data, ioaddr); dev->trans_start = jiffies; } else netdev_err(dev, "No Tx resource - Send_filter_frame!\n"); @@ -1457,37 +1481,38 @@ static void allocate_rx_buffer(struct net_device *dev) * Read one word data from the serial ROM */ -static u16 read_srom_word(long ioaddr, int offset) +static u16 read_srom_word(struct uli526x_board_info *db, int offset) { - int i; + void __iomem *ioaddr = db->ioaddr; u16 srom_data = 0; - long cr9_ioaddr = ioaddr + DCR9; + int i; - outl(CR9_SROM_READ, cr9_ioaddr); - outl(CR9_SROM_READ | CR9_SRCS, cr9_ioaddr); + uw32(DCR9, CR9_SROM_READ); + uw32(DCR9, CR9_SROM_READ | CR9_SRCS); /* Send the Read Command 110b */ - SROM_CLK_WRITE(SROM_DATA_1, cr9_ioaddr); - SROM_CLK_WRITE(SROM_DATA_1, cr9_ioaddr); - SROM_CLK_WRITE(SROM_DATA_0, cr9_ioaddr); + srom_clk_write(db, SROM_DATA_1); + srom_clk_write(db, SROM_DATA_1); + srom_clk_write(db, SROM_DATA_0); /* Send the offset */ for (i = 5; i >= 0; i--) { srom_data = (offset & (1 << i)) ? SROM_DATA_1 : SROM_DATA_0; - SROM_CLK_WRITE(srom_data, cr9_ioaddr); + srom_clk_write(db, srom_data); } - outl(CR9_SROM_READ | CR9_SRCS, cr9_ioaddr); + uw32(DCR9, CR9_SROM_READ | CR9_SRCS); for (i = 16; i > 0; i--) { - outl(CR9_SROM_READ | CR9_SRCS | CR9_SRCLK, cr9_ioaddr); + uw32(DCR9, CR9_SROM_READ | CR9_SRCS | CR9_SRCLK); udelay(5); - srom_data = (srom_data << 1) | ((inl(cr9_ioaddr) & CR9_CRDOUT) ? 1 : 0); - outl(CR9_SROM_READ | CR9_SRCS, cr9_ioaddr); + srom_data = (srom_data << 1) | + ((ur32(DCR9) & CR9_CRDOUT) ? 1 : 0); + uw32(DCR9, CR9_SROM_READ | CR9_SRCS); udelay(5); } - outl(CR9_SROM_READ, cr9_ioaddr); + uw32(DCR9, CR9_SROM_READ); return srom_data; } @@ -1498,15 +1523,16 @@ static u16 read_srom_word(long ioaddr, int offset) static u8 uli526x_sense_speed(struct uli526x_board_info * db) { + struct uli_phy_ops *phy = &db->phy; u8 ErrFlag = 0; u16 phy_mode; - phy_mode = phy_read(db->ioaddr, db->phy_addr, 1, db->chip_id); - phy_mode = phy_read(db->ioaddr, db->phy_addr, 1, db->chip_id); + phy_mode = phy->read(db, db->phy_addr, 1); + phy_mode = phy->read(db, db->phy_addr, 1); if ( (phy_mode & 0x24) == 0x24 ) { - phy_mode = ((phy_read(db->ioaddr, db->phy_addr, 5, db->chip_id) & 0x01e0)<<7); + phy_mode = ((phy->read(db, db->phy_addr, 5) & 0x01e0)<<7); if(phy_mode&0x8000) phy_mode = 0x8000; else if(phy_mode&0x4000) @@ -1541,10 +1567,11 @@ static u8 uli526x_sense_speed(struct uli526x_board_info * db) static void uli526x_set_phyxcer(struct uli526x_board_info *db) { + struct uli_phy_ops *phy = &db->phy; u16 phy_reg; /* Phyxcer capability setting */ - phy_reg = phy_read(db->ioaddr, db->phy_addr, 4, db->chip_id) & ~0x01e0; + phy_reg = phy->read(db, db->phy_addr, 4) & ~0x01e0; if (db->media_mode & ULI526X_AUTO) { /* AUTO Mode */ @@ -1565,10 +1592,10 @@ static void uli526x_set_phyxcer(struct uli526x_board_info *db) phy_reg|=db->PHY_reg4; db->media_mode|=ULI526X_AUTO; } - phy_write(db->ioaddr, db->phy_addr, 4, phy_reg, db->chip_id); + phy->write(db, db->phy_addr, 4, phy_reg); /* Restart Auto-Negotiation */ - phy_write(db->ioaddr, db->phy_addr, 0, 0x1200, db->chip_id); + phy->write(db, db->phy_addr, 0, 0x1200); udelay(50); } @@ -1582,6 +1609,7 @@ static void uli526x_set_phyxcer(struct uli526x_board_info *db) static void uli526x_process_mode(struct uli526x_board_info *db) { + struct uli_phy_ops *phy = &db->phy; u16 phy_reg; /* Full Duplex Mode Check */ @@ -1593,10 +1621,10 @@ static void uli526x_process_mode(struct uli526x_board_info *db) update_cr6(db->cr6_data, db->ioaddr); /* 10/100M phyxcer force mode need */ - if ( !(db->media_mode & 0x8)) { + if (!(db->media_mode & 0x8)) { /* Forece Mode */ - phy_reg = phy_read(db->ioaddr, db->phy_addr, 6, db->chip_id); - if ( !(phy_reg & 0x1) ) { + phy_reg = phy->read(db, db->phy_addr, 6); + if (!(phy_reg & 0x1)) { /* parter without N-Way capability */ phy_reg = 0x0; switch(db->op_mode) { @@ -1605,148 +1633,126 @@ static void uli526x_process_mode(struct uli526x_board_info *db) case ULI526X_100MHF: phy_reg = 0x2000; break; case ULI526X_100MFD: phy_reg = 0x2100; break; } - phy_write(db->ioaddr, db->phy_addr, 0, phy_reg, db->chip_id); + phy->write(db, db->phy_addr, 0, phy_reg); } } } -/* - * Write a word to Phy register - */ - -static void phy_write(unsigned long iobase, u8 phy_addr, u8 offset, u16 phy_data, u32 chip_id) +/* M5261/M5263 Chip */ +static void phy_writeby_cr9(struct uli526x_board_info *db, u8 phy_addr, + u8 offset, u16 phy_data) { u16 i; - unsigned long ioaddr; - - if(chip_id == PCI_ULI5263_ID) - { - phy_writeby_cr10(iobase, phy_addr, offset, phy_data); - return; - } - /* M5261/M5263 Chip */ - ioaddr = iobase + DCR9; /* Send 33 synchronization clock to Phy controller */ for (i = 0; i < 35; i++) - phy_write_1bit(ioaddr, PHY_DATA_1, chip_id); + phy_write_1bit(db, PHY_DATA_1); /* Send start command(01) to Phy */ - phy_write_1bit(ioaddr, PHY_DATA_0, chip_id); - phy_write_1bit(ioaddr, PHY_DATA_1, chip_id); + phy_write_1bit(db, PHY_DATA_0); + phy_write_1bit(db, PHY_DATA_1); /* Send write command(01) to Phy */ - phy_write_1bit(ioaddr, PHY_DATA_0, chip_id); - phy_write_1bit(ioaddr, PHY_DATA_1, chip_id); + phy_write_1bit(db, PHY_DATA_0); + phy_write_1bit(db, PHY_DATA_1); /* Send Phy address */ for (i = 0x10; i > 0; i = i >> 1) - phy_write_1bit(ioaddr, phy_addr & i ? PHY_DATA_1 : PHY_DATA_0, chip_id); + phy_write_1bit(db, phy_addr & i ? PHY_DATA_1 : PHY_DATA_0); /* Send register address */ for (i = 0x10; i > 0; i = i >> 1) - phy_write_1bit(ioaddr, offset & i ? PHY_DATA_1 : PHY_DATA_0, chip_id); + phy_write_1bit(db, offset & i ? PHY_DATA_1 : PHY_DATA_0); /* written trasnition */ - phy_write_1bit(ioaddr, PHY_DATA_1, chip_id); - phy_write_1bit(ioaddr, PHY_DATA_0, chip_id); + phy_write_1bit(db, PHY_DATA_1); + phy_write_1bit(db, PHY_DATA_0); /* Write a word data to PHY controller */ - for ( i = 0x8000; i > 0; i >>= 1) - phy_write_1bit(ioaddr, phy_data & i ? PHY_DATA_1 : PHY_DATA_0, chip_id); - + for (i = 0x8000; i > 0; i >>= 1) + phy_write_1bit(db, phy_data & i ? PHY_DATA_1 : PHY_DATA_0); } - -/* - * Read a word data from phy register - */ - -static u16 phy_read(unsigned long iobase, u8 phy_addr, u8 offset, u32 chip_id) +static u16 phy_readby_cr9(struct uli526x_board_info *db, u8 phy_addr, u8 offset) { - int i; u16 phy_data; - unsigned long ioaddr; - - if(chip_id == PCI_ULI5263_ID) - return phy_readby_cr10(iobase, phy_addr, offset); - /* M5261/M5263 Chip */ - ioaddr = iobase + DCR9; + int i; /* Send 33 synchronization clock to Phy controller */ for (i = 0; i < 35; i++) - phy_write_1bit(ioaddr, PHY_DATA_1, chip_id); + phy_write_1bit(db, PHY_DATA_1); /* Send start command(01) to Phy */ - phy_write_1bit(ioaddr, PHY_DATA_0, chip_id); - phy_write_1bit(ioaddr, PHY_DATA_1, chip_id); + phy_write_1bit(db, PHY_DATA_0); + phy_write_1bit(db, PHY_DATA_1); /* Send read command(10) to Phy */ - phy_write_1bit(ioaddr, PHY_DATA_1, chip_id); - phy_write_1bit(ioaddr, PHY_DATA_0, chip_id); + phy_write_1bit(db, PHY_DATA_1); + phy_write_1bit(db, PHY_DATA_0); /* Send Phy address */ for (i = 0x10; i > 0; i = i >> 1) - phy_write_1bit(ioaddr, phy_addr & i ? PHY_DATA_1 : PHY_DATA_0, chip_id); + phy_write_1bit(db, phy_addr & i ? PHY_DATA_1 : PHY_DATA_0); /* Send register address */ for (i = 0x10; i > 0; i = i >> 1) - phy_write_1bit(ioaddr, offset & i ? PHY_DATA_1 : PHY_DATA_0, chip_id); + phy_write_1bit(db, offset & i ? PHY_DATA_1 : PHY_DATA_0); /* Skip transition state */ - phy_read_1bit(ioaddr, chip_id); + phy_read_1bit(db); /* read 16bit data */ for (phy_data = 0, i = 0; i < 16; i++) { phy_data <<= 1; - phy_data |= phy_read_1bit(ioaddr, chip_id); + phy_data |= phy_read_1bit(db); } return phy_data; } -static u16 phy_readby_cr10(unsigned long iobase, u8 phy_addr, u8 offset) +static u16 phy_readby_cr10(struct uli526x_board_info *db, u8 phy_addr, + u8 offset) { - unsigned long ioaddr,cr10_value; + void __iomem *ioaddr = db->ioaddr; + u32 cr10_value = phy_addr; - ioaddr = iobase + DCR10; - cr10_value = phy_addr; - cr10_value = (cr10_value<<5) + offset; - cr10_value = (cr10_value<<16) + 0x08000000; - outl(cr10_value,ioaddr); + cr10_value = (cr10_value << 5) + offset; + cr10_value = (cr10_value << 16) + 0x08000000; + uw32(DCR10, cr10_value); udelay(1); - while(1) - { - cr10_value = inl(ioaddr); - if(cr10_value&0x10000000) + while (1) { + cr10_value = ur32(DCR10); + if (cr10_value & 0x10000000) break; } return cr10_value & 0x0ffff; } -static void phy_writeby_cr10(unsigned long iobase, u8 phy_addr, u8 offset, u16 phy_data) +static void phy_writeby_cr10(struct uli526x_board_info *db, u8 phy_addr, + u8 offset, u16 phy_data) { - unsigned long ioaddr,cr10_value; + void __iomem *ioaddr = db->ioaddr; + u32 cr10_value = phy_addr; - ioaddr = iobase + DCR10; - cr10_value = phy_addr; - cr10_value = (cr10_value<<5) + offset; - cr10_value = (cr10_value<<16) + 0x04000000 + phy_data; - outl(cr10_value,ioaddr); + cr10_value = (cr10_value << 5) + offset; + cr10_value = (cr10_value << 16) + 0x04000000 + phy_data; + uw32(DCR10, cr10_value); udelay(1); } /* * Write one bit data to Phy Controller */ -static void phy_write_1bit(unsigned long ioaddr, u32 phy_data, u32 chip_id) +static void phy_write_1bit(struct uli526x_board_info *db, u32 data) { - outl(phy_data , ioaddr); /* MII Clock Low */ + void __iomem *ioaddr = db->ioaddr; + + uw32(DCR9, data); /* MII Clock Low */ udelay(1); - outl(phy_data | MDCLKH, ioaddr); /* MII Clock High */ + uw32(DCR9, data | MDCLKH); /* MII Clock High */ udelay(1); - outl(phy_data , ioaddr); /* MII Clock Low */ + uw32(DCR9, data); /* MII Clock Low */ udelay(1); } @@ -1755,14 +1761,15 @@ static void phy_write_1bit(unsigned long ioaddr, u32 phy_data, u32 chip_id) * Read one bit phy data from PHY controller */ -static u16 phy_read_1bit(unsigned long ioaddr, u32 chip_id) +static u16 phy_read_1bit(struct uli526x_board_info *db) { + void __iomem *ioaddr = db->ioaddr; u16 phy_data; - outl(0x50000 , ioaddr); + uw32(DCR9, 0x50000); udelay(1); - phy_data = ( inl(ioaddr) >> 19 ) & 0x1; - outl(0x40000 , ioaddr); + phy_data = (ur32(DCR9) >> 19) & 0x1; + uw32(DCR9, 0x40000); udelay(1); return phy_data;