From: Tomasz Maciej Nowak Date: Tue, 25 Feb 2020 19:07:36 +0000 (+0100) Subject: layerscape: resurrect support for FRDM-LS1012A X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=3a3d998c129c3316c188b1abd9b2d3b0fc82ab2e;p=openwrt%2Fstaging%2Fwigyori.git layerscape: resurrect support for FRDM-LS1012A Re-add support for NXP FRDM-LS1012A, which mimics the flash layout of the rest boards supported by LSDK. 0x000000000000-0x000000100000 : "bl2" 0x000000100000-0x000000500000 : "fip" 0x000000500000-0x000000600000 : "u-boot-env" 0x000000600000-0x000000a00000 : "reserved-1" 0x000000a00000-0x000000d00000 : "pfe" 0x000000d00000-0x000000f00000 : "reserved-2" 0x000000f00000-0x000001000000 : "dtb" 0x000001000000-0x000002000000 : "kernel" 0x000002000000-0x000004000000 : "ubifs" Specification SoC: LS1012A single core 800MHz RAM: 512 MB DDR3 Flash: 64 MB QSPI NOR Ethernet: 2x 10/100/1000 Mbps Connectors: µUSB 3.0 OTG µUSB 2.0 (debugging & power input) 2x 3.5mm jack for microphone & headphone (SGTL5000) Arduino Shield expansion with I2C, SPI, UART, and GPIO JTAG LEDS: 3x (non-configurable) Buttons: 1x (reset, non-configurable) Be advised that erasing or writing 64MB flash takes some time to finish. Do not reset the board until all operations end with success, otherwise You'll need external tools to re-program the flash chip. Installation Follow the QSPI programing procedure for LS1012AFRWY board in target/linux/layerscape/README, point 3.3. Don't forget about updating U-Boot environment with MAC addresses of ethernet interfaces, variable 'ethaddr' for eth0 and 'eth1addr' for eth1. As the LSDK images do not support sysupgrade, nor do changes in this commit, it's planed in upcoming submissions. Signed-off-by: Tomasz Maciej Nowak --- diff --git a/package/boot/tfa-layerscape/Makefile b/package/boot/tfa-layerscape/Makefile index a34c52bc3b..d2da84ec15 100644 --- a/package/boot/tfa-layerscape/Makefile +++ b/package/boot/tfa-layerscape/Makefile @@ -69,6 +69,14 @@ define Host/Install $(INSTALL_BIN) $(HOST_BUILD_DIR)/plat/nxp/tools/byte_swap $(STAGING_DIR_HOST)/bin/tfa-byte-swap endef +define Package/tfa-layerscape/ls1012afrdm + TITLE:=NXP LS1012AFRDM Trusted Firmware + PLAT:=ls1012afrdm + BOOT_MODE:=qspi + BIN_BL2:=build/ls1012afrdm/release/bl2_qspi.pbl + BIN_FIP:=build/ls1012afrdm/release/fip.bin +endef + define Package/tfa-layerscape/ls1012ardb TITLE:=NXP LS1012ARDB Trusted Firmware PLAT:=ls1012ardb @@ -142,6 +150,7 @@ define Package/tfa-layerscape/ls2088ardb endef TFAS := \ + ls1012afrdm \ ls1012ardb \ ls1012afrwy \ ls1043ardb \ diff --git a/package/boot/uboot-layerscape/Makefile b/package/boot/uboot-layerscape/Makefile index ddf71bd986..63c16a7db0 100644 --- a/package/boot/uboot-layerscape/Makefile +++ b/package/boot/uboot-layerscape/Makefile @@ -27,6 +27,12 @@ define U-Boot/Default ENV_SIZE:=0x2000 endef +define U-Boot/ls1012afrdm + NAME:=NXP LS1012AFRDM + UBOOT_CONFIG:=ls1012afrdm_tfa + ENV_SIZE:=0x40000 +endef + define U-Boot/ls1012ardb NAME:=NXP LS1012ARDB UBOOT_CONFIG:=ls1012ardb_tfa @@ -102,6 +108,7 @@ endef UBOOT_TARGETS := \ + ls1012afrdm \ ls1012ardb \ ls1012afrwy \ ls1043ardb \ diff --git a/package/boot/uboot-layerscape/files/ls1012afrdm-uEnv.txt b/package/boot/uboot-layerscape/files/ls1012afrdm-uEnv.txt new file mode 100644 index 0000000000..ccc98dd299 --- /dev/null +++ b/package/boot/uboot-layerscape/files/ls1012afrdm-uEnv.txt @@ -0,0 +1,8 @@ +fdtaddr=0x8f000000 +loadaddr=0x81000000 +fdt_high=0xffffffffffffffff +initrd_high=0xffffffffffffffff +qspi_boot=sf probe 0:0;sf read $fdtaddr f00000 100000;sf read $loadaddr 1000000 1000000;bootm $loadaddr - $fdtaddr +bootargs=ubi.mtd=8 root=ubi0:rootfs rw rootfstype=ubifs noinitrd earlycon=uart8250,mmio,0x21c0500 console=ttyS0,115200 mtdparts=1550000.quadspi:1m(bl2),4m(fip),1m(u-boot-env),4m(reserved-1),3m(pfe),2m(reserved-2),1m(dtb),16m(kernel),32m(ubifs) +bootcmd=echo starting OpenWrt ...;pfe stop;run qspi_boot +bootdelay=3 diff --git a/package/firmware/layerscape/ls-rcw/Makefile b/package/firmware/layerscape/ls-rcw/Makefile index 5bcbff5bc4..ddef58fa0b 100644 --- a/package/firmware/layerscape/ls-rcw/Makefile +++ b/package/firmware/layerscape/ls-rcw/Makefile @@ -28,6 +28,11 @@ define Package/layerscape-rcw/Config endef endef +define Package/layerscape-rcw/ls1012afrdm + TITLE:=NXP LS1012AFRDM RCW binary + CONFIG:=ls1012afrdm/N_SSNP_3305/rcw_800.bin +endef + define Package/layerscape-rcw/ls1012ardb TITLE:=NXP LS1012ARDB RCW binary CONFIG:=ls1012ardb/R_SPNH_3508/rcw_1000_default.bin @@ -86,6 +91,7 @@ define Package/layerscape-rcw/Install endef RCWS := \ + ls1012afrdm \ ls1012ardb \ ls1012afrwy \ ls1043ardb \ diff --git a/target/linux/layerscape/image/armv8_64b.mk b/target/linux/layerscape/image/armv8_64b.mk index 61ea849119..0322183b96 100644 --- a/target/linux/layerscape/image/armv8_64b.mk +++ b/target/linux/layerscape/image/armv8_64b.mk @@ -15,6 +15,29 @@ define Device/Default KERNEL_ENTRY_POINT := 0x80080000 endef +define Device/ls1012afrdm + DEVICE_VENDOR := NXP + DEVICE_MODEL := FRDM-LS1012A + DEVICE_PACKAGES += \ + layerscape-ppfe \ + tfa-ls1012afrdm \ + kmod-ppfe + DEVICE_DTS := freescale/fsl-ls1012a-frdm + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 256KiB + PAGESIZE := 1 + IMAGE/firmware.bin := \ + ls-clean | \ + ls-append $(1)-bl2.pbl | pad-to 1M | \ + ls-append $(1)-fip.bin | pad-to 5M | \ + ls-append $(1)-uboot-env.bin | pad-to 10M | \ + ls-append pfe.itb | pad-to 15M | \ + ls-append-dtb $$(DEVICE_DTS) | pad-to 16M | \ + append-kernel | pad-to 32M | \ + append-ubi | check-size 67108865 +endef +TARGET_DEVICES += ls1012afrdm + define Device/ls1012ardb DEVICE_VENDOR := NXP DEVICE_MODEL := LS1012A-RDB