From: Isaev Ruslan Date: Thu, 2 Nov 2023 03:08:53 +0000 (+0300) Subject: ipq807x: add support for Yuncore AX880 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=3763a6a0752cec6e9d7a7d71d9c0cbdfcd35a2e7;p=openwrt%2Fstaging%2Fdangole.git ipq807x: add support for Yuncore AX880 SPECIFICATION: - Chipset: IPQ8072A +QCN5054+QCN5024+QCA8081*2 - Flash NOR-8MB AND NAND-128MB - RAM 1Gb DDR - IEEE 802.11: 802.11ax/ac/b/g/n - 4*4 2.4G Wi-Fi standard 802.11b/g/n/ax - 4*4 5.8G Wi-Fi Standard 802.11 a/n/ac/ax - 2x 1 Gbps Ethernet (QCA8081) with 802.3at PoE input support - 1x Reset - 1x Bluetooth(optional) - 1x DC Port 12V 3A - 4x Antenna IPEX Connector, 3dBi omni antennas - Data Rate: 3657Mbps ( 2.4G: 1182Mbps (11ax 4x4); 5.8G: 2475Mbps (11ax 4x4)) - RF Power: 2.4g ≤ 20dBm; 5.8g ≤ 19dBm - LED light: Sys; 5.8G wifi; 2.4G wifi; WAN; LAN - Max Power Consumption: ≤ 22W - Size: 198mm * 198mm * 41.02mm BACKUP YOUR STOCK FIRMWARE: ``` export device=ax880 mkdir -p /tmp/fw_dump_$device cd /tmp/fw_dump_$device dmesg > dmesg_$device.log dtc -I fs /sys/firmware/devicetree/base > $device.dts cat /proc/device-tree/model > model cat /proc/mtd > proc_mtd while read p; do mtd_dev=$(echo $p | cut -d: -f1) echo $mtd_dev dd if=/dev/$mtd_dev of=$mtd_dev done < proc_mtd md5sum * > md5sum.log tar -cvzf ../$device.tar.gz . export sum=$(md5sum /tmp/$device.tar.gz | cut -d' ' -f1) mv ../$device.tar.gz /tmp/${device}_${sum}.tar.gz echo fw backup saved to: /tmp/${device}_${sum}.tar.gz ``` Upload your backup via tftp to the safe place. INSTALLATION: 1. stock firmware web ui Rename factory.bin fw image file to factory.ubin. Flash this image like ordinary stock fw upgrade. 2. stock firmware telnet method Enter telnet cli (login: root, password: 476t*_f0%g09y) and upload factory.bin fw image and rename it to factory.ubin `cd /tmp && wget /factory.ubin` `sysupgrade factory.ubin 3. initramfs method Put openwrt-ipq807x-generic-yuncore_ax880-initramfs-uImage.itb to your TFTP server and rename it to ax880.initram Enable serial console and enter to the u-boot cli. Exec these commands: `tftpboot :ax880.initram` `dhcp` When downloading is finished: `bootm` After booting the device, you need to upload to the device factory.ubi fw image. ``` cd /tmp && wget /factory.ubi` export rootfs=$(cat /proc/mtd | grep rootfs | cut -d: -f1) export rootfs_1=$(cat /proc/mtd | grep rootfs_1 | cut -d: -f1) ubiformat /dev/${rootfs} -y -f factory.ubi ubiformat /dev/${rootfs_1} -y -f factory.ubi reboot ``` 4. u-boot factory.ubi image method Put openwrt-ipq807x-generic-yuncore_ax880-squashfs-factory.ubi to your TFTP server and rename it to ax880.ubi Enter u-boot cli and exec these commands: `tftpboot :ax880.ubi` `dhcp` After downloading is finished: `flash rootfs` `flash rootfs_1` `reset` 5. u-boot factory.bin method Put openwrt-ipq807x-generic-yuncore_ax880-squashfs-factory.bin to your TFTP server and rename it to ax880.bin Enter u-boot cli and exec these commands: `tftpboot :ax880.bin` `dhcp` After downloading is finished: `imgaddr=$fileaddr && nand device 0` Erase rootfs memory: `nand erase 0x00000000 0x03400000` Write rootfs: `nand write $fileaddr 0x00000000 $filesize` Erase rootfs_1 memory: `nand erase 0x3c00000 0x3400000` Write rootfs_1 `nand write $fileaddr 0x3c00000 $filesize` `reset` STOCK FIRMWARE RECOVERY: Boot initramfs image. Upload your rootfs mtd partition to the device using scp or download it from the device using wget. Enter device ssh cli and exec: ``` cd /tmp && wget /mtd21` export rootfs=$(cat /proc/mtd | grep rootfs | cut -d: -f1) export rootfs_1=$(cat /proc/mtd | grep rootfs_1 | cut -d: -f1) ubiformat /dev/${rootfs} -y -f /tmp/mtd21 ubiformat /dev/${rootfs_1} -y -f /tmp/mtd21 reboot ``` Signed-off-by: Isaev Ruslan Reviewed-by: Robert Marko --- diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index 1d7dcfef86..8736a1a583 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -6,9 +6,9 @@ PKG_RELEASE:=1 PKG_SOURCE_PROTO:=git PKG_SOURCE_URL=$(PROJECT_GIT)/project/firmware/qca-wireless.git -PKG_SOURCE_DATE:=2023-10-12 -PKG_SOURCE_VERSION:=cd04ab7f984fe28613276c01fd0ac7afbe5516d5 -PKG_MIRROR_HASH:=857ae436fd09785749411a665b31c82cec84b68b1e096f69ebb6c2a0efb5583f +PKG_SOURCE_DATE:=2023-11-02 +PKG_SOURCE_VERSION:=371d4dce9b9a4b4dfd59bc902bb216f7133743cb +PKG_MIRROR_HASH:=9c309f81cb1e464580ccdacc3f7a660df8a5a07a8b87f71e9d00f630ac0412ad PKG_FLAGS:=nonshared @@ -44,6 +44,7 @@ ALLWIFIBOARDS:= \ xiaomi_ax3600 \ xiaomi_ax9000 \ yyets_le1 \ + yuncore_ax880 \ zte_mf289f \ zte_mf287 \ zte_mf287plus \ @@ -151,6 +152,7 @@ $(eval $(call generate-ipq-wifi-package,wallys_dr40x9,Wallys DR40X9)) $(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600)) $(eval $(call generate-ipq-wifi-package,xiaomi_ax9000,Xiaomi AX9000)) $(eval $(call generate-ipq-wifi-package,yyets_le1,YYeTs LE1)) +$(eval $(call generate-ipq-wifi-package,yuncore_ax880,Yuncore AX880)) $(eval $(call generate-ipq-wifi-package,zte_mf289f,ZTE MF289F)) $(eval $(call generate-ipq-wifi-package,zte_mf287,ZTE MF287)) $(eval $(call generate-ipq-wifi-package,zte_mf287plus,ZTE MF287Plus)) diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-ax880.dts b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-ax880.dts new file mode 100644 index 0000000000..1aefa2c924 --- /dev/null +++ b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-ax880.dts @@ -0,0 +1,370 @@ +// SPDX-License-Identifier: MIT, GPL-2.0 or later +/* Copyright (c) 2023, Ruslan Isaev */ + +/dts-v1/; + +#include "ipq8074.dtsi" +#include "ipq8074-hk-cpu.dtsi" +#include "ipq8074-ess.dtsi" +#include +#include + +/ { + model = "Yuncore AX880"; + compatible = "yuncore,ax880", "qcom,ipq8074", "qcom,ipq8074-hk09"; + + aliases { + serial0 = &blsp1_uart5; + serial1 = &blsp1_uart3; + led-boot = &led_system; + led-failsafe = &led_system; + led-running = &led_system; + led-upgrade = &led_system; + /* Aliases as required by u-boot to patch MAC addresses */ + ethernet0 = &dp5_syn; + ethernet1 = &dp6_syn; + label-mac-device = &dp5_syn; + }; + + chosen { + stdout-path = "serial0:115200n8"; + bootargs-append = " root=/dev/ubiblock0_1"; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + reset { + label = "reset"; + gpios = <&tlmm 57 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_system: system { + label = "system"; + color = "red"; + gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>; + }; + + wlan2g { + label = "wlan2g"; + color = "green"; + linux,default-trigger = "phy0tpt"; + gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>; + }; + + wlan5g { + label = "wlan5g"; + color = "blue"; + linux,default-trigger = "phy1tpt"; + gpios = <&tlmm 9 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&tlmm { + mdio_pins: mdio-pins { + mdc { + pins = "gpio68"; + function = "mdc"; + drive-strength = <8>; + bias-pull-up; + }; + + mdio { + pins = "gpio69"; + function = "mdio"; + drive-strength = <8>; + bias-pull-up; + }; + }; + + button_pins: button_pins { + reset_button { + pins = "gpio57"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + }; + }; +}; + +&blsp1_spi1 { + status = "okay"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <50000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:sbl1"; + reg = <0x0 0x50000>; + read-only; + }; + + partition@50000 { + label = "0:mibib"; + reg = <0x50000 0x10000>; + read-only; + }; + + partition@60000 { + label = "0:bootconfig"; + reg = <0x60000 0x20000>; + read-only; + }; + + partition@80000 { + label = "0:bootconfig1"; + reg = <0x80000 0x20000>; + read-only; + }; + + partition@a0000 { + label = "0:qsee_1"; + reg = <0xa0000 0x180000>; + read-only; + }; + + partition@220000 { + label = "0:qsee"; + reg = <0x220000 0x180000>; + read-only; + }; + + partition@3a0000 { + label = "0:devcfg"; + reg = <0x3a0000 0x10000>; + read-only; + }; + + partition@3b0000 { + label = "0:devcfg_1"; + reg = <0x3b0000 0x10000>; + read-only; + }; + + partition@3c0000 { + label = "0:apdp"; + reg = <0x3c0000 0x10000>; + read-only; + }; + + partition@3d0000 { + label = "0:apdp_1"; + reg = <0x3d0000 0x10000>; + read-only; + }; + + partition@3e0000 { + label = "0:rpm_1"; + reg = <0x3e0000 0x40000>; + read-only; + }; + + partition@420000 { + label = "0:rpm"; + reg = <0x420000 0x40000>; + read-only; + }; + + partition@460000 { + label = "0:cdt_1"; + reg = <0x460000 0x10000>; + read-only; + }; + + partition@470000 { + label = "0:cdt"; + reg = <0x470000 0x10000>; + read-only; + }; + + partition@480000 { + label = "0:appsblenv"; + reg = <0x480000 0x10000>; + }; + + partition@490000 { + label = "0:appsbl_1"; + reg = <0x490000 0xa0000>; + read-only; + }; + + partition@550000 { + label = "0:appsbl"; + reg = <0x530000 0xa0000>; + read-only; + }; + + partition@610000 { + label = "0:art"; + reg = <0x5d0000 0x40000>; + read-only; + }; + + partition@650000 { + label = "0:ethphyfw"; + reg = <0x610000 0x80000>; + read-only; + }; + + }; + }; +}; + +//serial interface +&blsp1_uart3 { + status = "okay"; +}; + +&blsp1_uart5 { + status = "okay"; +}; + +&crypto { + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&prng { + status = "okay"; +}; + +&qpic_bam { + status = "okay"; +}; + +&qusb_phy_0 { + status = "okay"; +}; + +&ssphy_0 { + status = "okay"; +}; + +&usb_0 { + status = "okay"; +}; + +&qpic_nand { + status = "okay"; + + nand@0 { + reg = <0>; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-bus-width = <8>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "rootfs_1"; + reg = <0x0000000 0x3400000>; + }; + + partition@3400000 { + label = "0:wififw"; + reg = <0x3400000 0x800000>; + read-only; + }; + + rootfs: partition@3c00000 { + label = "rootfs"; + reg = <0x3c00000 0x3400000>; + }; + + partition@7000000 { + label = "0:wififw_1"; + reg = <0x7000000 0x800000>; + read-only; + }; + }; + }; +}; + +&mdio { + status = "okay"; + + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + + qca8081_24: ethernet-phy@24 { + compatible = "ethernet-phy-id004d.d101"; + reg = <24>; + reset-gpios = <&tlmm 33 GPIO_ACTIVE_LOW>; + }; + + qca8081_28: ethernet-phy@28 { + compatible = "ethernet-phy-id004d.d101"; + reg = <28>; + reset-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>; + }; +}; + +&switch { + status = "okay"; + + switch_cpu_bmp = <0x1>; /* cpu port bitmap */ + switch_lan_bmp = <0x3e>; /* lan port bitmap */ + switch_wan_bmp = <0x40>; /* wan port bitmap */ + switch_mac_mode = <0xff>; /* mac mode for uniphy instance0*/ + switch_mac_mode1 = <0xf>; /* mac mode for uniphy instance1*/ + switch_mac_mode2 = <0xf>; /* mac mode for uniphy instance2*/ + bm_tick_mode = <0>; /* bm tick mode */ + tm_tick_mode = <0>; /* tm tick mode */ + + qcom,port_phyinfo { + port@4 { + port_id = <5>; + phy_address = <24>; + port_mac_sel = "QGMAC_PORT"; + }; + port@5 { + port_id = <6>; + phy_address = <28>; + port_mac_sel = "QGMAC_PORT"; + }; + }; +}; + +&edma { + status = "okay"; +}; + +&dp5_syn { + status = "okay"; + phy-handle = <&qca8081_24>; + label = "wan"; +}; + +&dp6_syn { + status = "okay"; + phy-handle = <&qca8081_28>; + label = "lan"; +}; + +&wifi { + status = "okay"; + qcom,ath11k-calibration-variant = "Yuncore-AX880"; +}; diff --git a/target/linux/qualcommax/image/ipq807x.mk b/target/linux/qualcommax/image/ipq807x.mk index 0be17333b2..ee7707540b 100644 --- a/target/linux/qualcommax/image/ipq807x.mk +++ b/target/linux/qualcommax/image/ipq807x.mk @@ -253,3 +253,19 @@ define Device/zyxel_nbg7815 kmod-bluetooth endef TARGET_DEVICES += zyxel_nbg7815 + +define Device/yuncore_ax880 + $(call Device/FitImage) + $(call Device/UbiFit) + DEVICE_VENDOR := Yuncore + DEVICE_MODEL := AX880 + BLOCKSIZE := 128k + PAGESIZE := 2048 + DEVICE_DTS_CONFIG := config@hk09 + SOC := ipq8072 + DEVICE_PACKAGES := ipq-wifi-yuncore_ax880 + IMAGES += factory.bin + IMAGE/factory.bin := append-ubi | qsdk-ipq-factory-nand +endef +TARGET_DEVICES += yuncore_ax880 + diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network index 11101794c3..95f1ab4bdf 100644 --- a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network +++ b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network @@ -16,7 +16,8 @@ ipq807x_setup_interfaces() xiaomi,ax9000) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan" ;; - edgecore,eap102) + edgecore,eap102|\ + yuncore,ax880) ucidef_set_interfaces_lan_wan "lan" "wan" ;; edimax,cax1800) diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata index 394c22d021..f427009669 100644 --- a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata +++ b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata @@ -22,6 +22,7 @@ case "$FIRMWARE" in redmi,ax6|\ xiaomi,ax3600|\ xiaomi,ax9000|\ + yuncore,ax880|\ zyxel,nbg7815) caldata_extract "0:art" 0x1000 0x20000 ;; diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/init.d/bootcount b/target/linux/qualcommax/ipq807x/base-files/etc/init.d/bootcount index 6917446a9b..84f826b3b8 100755 --- a/target/linux/qualcommax/ipq807x/base-files/etc/init.d/bootcount +++ b/target/linux/qualcommax/ipq807x/base-files/etc/init.d/bootcount @@ -4,7 +4,8 @@ START=99 boot() { case $(board_name) in - edgecore,eap102) + edgecore,eap102|\ + yuncore,ax880) fw_setenv upgrade_available 0 # Unset changed flag after sysupgrade complete fw_setenv changed diff --git a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh index e2c713c3db..19bd54cf4e 100644 --- a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh +++ b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh @@ -113,6 +113,18 @@ platform_do_upgrade() { CI_ROOT_UBIPART="rootfs" nand_do_upgrade "$1" ;; + yuncore,ax880) + active="$(fw_printenv -n active)" + if [ "$active" -eq "1" ]; then + CI_UBIPART="rootfs_1" + else + CI_UBIPART="rootfs" + fi + # force altbootcmd which handles partition change in u-boot + fw_setenv bootcount 3 + fw_setenv upgrade_available 1 + nand_do_upgrade "$1" + ;; *) default_do_upgrade "$1" ;;