From: Pawel Dembicki Date: Tue, 14 Nov 2023 08:09:11 +0000 (+0100) Subject: kirkwood: copy patches 5.15 to 6.1 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=36aff2a86e1160dbb7be172388b1653870eaf335;p=openwrt%2Fstaging%2Fdangole.git kirkwood: copy patches 5.15 to 6.1 Simple copy 5.15 patches. Upstreamed patch dropped: 001-5.18-Add-Ctera-C-200-V1-board.patch Signed-off-by: Pawel Dembicki (kirkwoor -> kirkwood in subject) Signed-off-by: Christian Lamparter --- diff --git a/target/linux/kirkwood/patches-6.1/002-6.2-ARM-dts-kirkwood-Add-Zyxel-NSA310S-board.patch b/target/linux/kirkwood/patches-6.1/002-6.2-ARM-dts-kirkwood-Add-Zyxel-NSA310S-board.patch new file mode 100644 index 0000000000..b745ea104f --- /dev/null +++ b/target/linux/kirkwood/patches-6.1/002-6.2-ARM-dts-kirkwood-Add-Zyxel-NSA310S-board.patch @@ -0,0 +1,301 @@ +From e977a103840c57d72b52cbc8c17f87f86ef9aa8d Mon Sep 17 00:00:00 2001 +From: Pawel Dembicki +Date: Sat, 29 Oct 2022 22:57:38 +0200 +Subject: [PATCH] ARM: dts: kirkwood: Add Zyxel NSA310S board + +Zyxel NSA310S is a NAS based on Marvell kirkwood SoC. + +Specification: + - Processor Marvell 88F6702 1 GHz + - 256MB RAM + - 128MB NAND + - 1x GBE LAN port (PHY: Marvell 88E1318) + - 2x USB 2.0 + - 1x SATA + - 3x button + - 7x leds + - serial on J1 connector (115200 8N1) (GND-NOPIN-RX-TX-VCC) + +Tested-by: Tony Dinh +Signed-off-by: Pawel Dembicki +Acked-by: Adam Baker +Reviewed-by: Andrew Lunn +Signed-off-by: Gregory CLEMENT +--- + arch/arm/boot/dts/Makefile | 1 + + arch/arm/boot/dts/kirkwood-nsa310s.dts | 259 +++++++++++++++++++++++++ + 2 files changed, 260 insertions(+) + create mode 100644 arch/arm/boot/dts/kirkwood-nsa310s.dts + +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -320,6 +320,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ + kirkwood-ns2mini.dtb \ + kirkwood-nsa310.dtb \ + kirkwood-nsa310a.dtb \ ++ kirkwood-nsa310s.dtb \ + kirkwood-nsa320.dtb \ + kirkwood-nsa325.dtb \ + kirkwood-openblocks_a6.dtb \ +--- /dev/null ++++ b/arch/arm/boot/dts/kirkwood-nsa310s.dts +@@ -0,0 +1,259 @@ ++// SPDX-License-Identifier: (GPL-2.0+ OR MIT) ++/* ++ * ZyXEL NSA310S Board Description ++ * Copyright 2020-2022 Pawel Dembicki ++ * Copyright (c) 2015-2021, Tony Dinh ++ * Copyright (c) 2014, Adam Baker ++ * Based upon the board setup file created by Peter Schildmann ++ */ ++/dts-v1/; ++ ++#include "kirkwood.dtsi" ++#include "kirkwood-6281.dtsi" ++#include ++ ++/ { ++ model = "ZyXEL NSA310S"; ++ compatible = "zyxel,nsa310s", "marvell,kirkwood-88f6702", "marvell,kirkwood"; ++ ++ memory { ++ device_type = "memory"; ++ reg = <0x00000000 0x10000000>; ++ }; ++ ++ chosen { ++ bootargs = "console=ttyS0,115200n8 earlyprintk"; ++ stdout-path = &uart0; ++ }; ++ ++ gpio_poweroff { ++ compatible = "gpio-poweroff"; ++ pinctrl-0 = <&pmx_pwr_off>; ++ pinctrl-names = "default"; ++ gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ keys { ++ compatible = "gpio-keys"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-0 = <&pmx_buttons>; ++ pinctrl-names = "default"; ++ ++ power { ++ label = "Power Button"; ++ linux,code = ; ++ gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ copy { ++ label = "Copy Button"; ++ linux,code = ; ++ gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; ++ }; ++ ++ reset { ++ label = "Reset Button"; ++ linux,code = ; ++ gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++ ++ leds { ++ compatible = "gpio-leds"; ++ pinctrl-0 = <&pmx_leds>; ++ pinctrl-names = "default"; ++ ++ led-1 { ++ function = LED_FUNCTION_DISK_ERR; ++ color = ; ++ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ led-2 { ++ function = LED_FUNCTION_USB; ++ color = ; ++ gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; ++ linux,default-trigger = "usb-host"; ++ }; ++ ++ led-3 { ++ function = LED_FUNCTION_DISK; ++ color = ; ++ gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>; ++ linux,default-trigger = "ata1"; ++ }; ++ ++ led-4 { ++ function = LED_FUNCTION_INDICATOR; ++ color = ; ++ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ led-5 { ++ function = LED_FUNCTION_INDICATOR; ++ color = ; ++ gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ led-6 { ++ function = LED_FUNCTION_STATUS; ++ color = ; ++ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; ++ linux,default-trigger = "default-on"; ++ }; ++ ++ led-7 { ++ function = LED_FUNCTION_STATUS; ++ color = ; ++ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; ++ }; ++ }; ++ ++ usb0_power: regulator@1 { ++ compatible = "regulator-fixed"; ++ regulator-name = "USB Power"; ++ ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ regulator-always-on; ++ regulator-boot-on; ++ gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ sata1_power: regulator@2 { ++ compatible = "regulator-fixed"; ++ regulator-name = "SATA1 Power"; ++ ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ regulator-always-on; ++ regulator-boot-on; ++ gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ thermal-zones { ++ disk-thermal { ++ polling-delay = <20000>; ++ polling-delay-passive = <2000>; ++ ++ thermal-sensors = <&hdd_temp>; ++ ++ trips { ++ disk_alert: disk-alert { ++ temperature = <40000>; ++ hysteresis = <5000>; ++ type = "active"; ++ }; ++ disk_crit: disk-crit { ++ temperature = <60000>; ++ hysteresis = <2000>; ++ type = "critical"; ++ }; ++ }; ++ }; ++ }; ++}; ++ ++ ++ð0 { ++ status = "okay"; ++ ++ ethernet0-port@0 { ++ phy-handle = <ðphy0>; ++ }; ++}; ++ ++&i2c0 { ++ status = "okay"; ++ ++ rtc@68 { ++ compatible = "htk,ht1382"; ++ reg = <0x68>; ++ }; ++}; ++ ++&mdio { ++ status = "okay"; ++ ++ ethphy0: ethernet-phy@1 { ++ reg = <1>; ++ phy-mode = "rgmii-id"; ++ marvell,reg-init = <0x1 0x16 0x0 0x3>, ++ <0x1 0x10 0x0 0x1017>, ++ <0x1 0x11 0x0 0x4408>, ++ <0x1 0x16 0x0 0x0>; ++ }; ++}; ++ ++&nand { ++ status = "okay"; ++ chip-delay = <35>; ++ ++ partition@0 { ++ label = "uboot"; ++ reg = <0x0000000 0x00c0000>; ++ read-only; ++ }; ++ partition@c0000 { ++ label = "uboot_env"; ++ reg = <0x00c0000 0x0080000>; ++ }; ++ partition@140000 { ++ label = "ubi"; ++ reg = <0x0140000 0x7ec0000>; ++ }; ++}; ++ ++&pciec { ++ status = "okay"; ++}; ++ ++&pcie0 { ++ status = "okay"; ++}; ++ ++&pinctrl { ++ pinctrl-names = "default"; ++ ++ pmx_buttons: pmx-buttons { ++ marvell,pins = "mpp24", "mpp25", "mpp26"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_leds: pmx-leds { ++ marvell,pins = "mpp13", "mpp15", "mpp16", "mpp22", "mpp23", ++ "mpp28", "mpp29"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_power: pmx-power { ++ marvell,pins = "mpp21", "mpp33"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_pwr_off: pmx-pwr-off { ++ marvell,pins = "mpp27"; ++ marvell,function = "gpio"; ++ }; ++}; ++ ++&rtc { ++ status = "disabled"; ++}; ++ ++&sata { ++ status = "okay"; ++ nr-ports = <1>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ hdd_temp: sata-port@0 { ++ reg = <0>; ++ #thermal-sensor-cells = <0>; ++ }; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; diff --git a/target/linux/kirkwood/patches-6.1/003-6.5-ARM-dts-kirkwood-Add-Endian-4i-Edge-200-board.patch b/target/linux/kirkwood/patches-6.1/003-6.5-ARM-dts-kirkwood-Add-Endian-4i-Edge-200-board.patch new file mode 100644 index 0000000000..4b0f46bb6d --- /dev/null +++ b/target/linux/kirkwood/patches-6.1/003-6.5-ARM-dts-kirkwood-Add-Endian-4i-Edge-200-board.patch @@ -0,0 +1,249 @@ +From 5668d088ee4ea05db9daaae0645d1d1f579b20f9 Mon Sep 17 00:00:00 2001 +From: Pawel Dembicki +Date: Mon, 3 Oct 2022 09:34:43 +0200 +Subject: ARM: dts: kirkwood: Add Endian 4i Edge 200 board + +Add Endian 4i Edge 200 is 5-port firewall. +It have also clone: Endian UTM Mini (The same hardware, with added WLAN +card). + +Hardware: + - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz + - Ram: 512MB (4x Nanya NT5TU128M8GE-AC) + - NAND Flash: 512MB (Micron 29F4G08AAC) + - Lan 1-4: 4x GBE (Marvell 88E6171R-TFJ2) + - Lan 5: 1x GBE (Marvell 88E1116R-NNC1) + - Storage: MicroSD Slot + - MCPIE: MiniPCIe Slot present [fitted with SparkLan WPEA-110N/E + (Atheros AR9280 chipset) in Endian UTM Mini WLAN only] + - USB: 1x USB 2.0 port + - Console: RJ-45 port + - LEDs: 3x GPIO controlled + +Signed-off-by: Pawel Dembicki +Reviewed-by: Andrew Lunn +Signed-off-by: Gregory CLEMENT +--- + arch/arm/boot/dts/Makefile | 1 + + arch/arm/boot/dts/kirkwood-4i-edge-200.dts | 205 +++++++++++++++++++++++++++++ + 2 files changed, 206 insertions(+) + create mode 100644 arch/arm/boot/dts/kirkwood-4i-edge-200.dts + +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -265,6 +265,7 @@ dtb-$(CONFIG_ARCH_KEYSTONE) += \ + keystone-k2g-evm.dtb \ + keystone-k2g-ice.dtb + dtb-$(CONFIG_MACH_KIRKWOOD) += \ ++ kirkwood-4i-edge-200.dtb \ + kirkwood-b3.dtb \ + kirkwood-blackarmor-nas220.dtb \ + kirkwood-c200-v1.dtb \ +--- /dev/null ++++ b/arch/arm/boot/dts/kirkwood-4i-edge-200.dts +@@ -0,0 +1,205 @@ ++// SPDX-License-Identifier: (GPL-2.0+ OR MIT) ++/* ++ * Endian 4i Edge 200 Board Description ++ * Note: Endian UTM Mini is hardware clone of Endian Edge 200 ++ * Copyright 2021-2022 Pawel Dembicki ++ */ ++ ++/dts-v1/; ++ ++#include "kirkwood.dtsi" ++#include "kirkwood-6281.dtsi" ++#include ++ ++/ { ++ model = "Endian 4i Edge 200"; ++ compatible = "endian,4i-edge-200", "marvell,kirkwood-88f6281", "marvell,kirkwood"; ++ ++ memory { ++ device_type = "memory"; ++ reg = <0x00000000 0x20000000>; ++ }; ++ ++ chosen { ++ bootargs = "console=ttyS0,115200n8"; ++ stdout-path = &uart0; ++ }; ++ ++ leds { ++ compatible = "gpio-leds"; ++ pinctrl-0 = <&pmx_led>; ++ pinctrl-names = "default"; ++ ++ led-1 { ++ function = LED_FUNCTION_SD; ++ color = ; ++ gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; ++ linux,default-trigger = "mmc0"; ++ }; ++ ++ led-2 { ++ function = LED_FUNCTION_STATUS; ++ color = ; ++ gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ led-3 { ++ function = LED_FUNCTION_STATUS; ++ color = ; ++ gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>; ++ }; ++ }; ++}; ++ ++ð0 { ++ status = "okay"; ++}; ++ ++ð0port { ++ speed = <1000>; ++ duplex = <1>; ++}; ++ ++ð1 { ++ status = "okay"; ++}; ++ ++ð1port { ++ phy-handle = <ðphyb>; ++}; ++ ++&mdio { ++ status = "okay"; ++ ++ ethphyb: ethernet-phy@b { ++ reg = <0x0b>; ++ ++ marvell,reg-init = ++ /* link-activity, bi-color mode 4 */ ++ <3 0x10 0xfff0 0xf>; /* Reg 3,16 <- 0xzzzf */ ++ }; ++ ++ switch0: switch@11 { ++ compatible = "marvell,mv88e6085"; ++ reg = <0x11>; ++ ++ ports { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ port@0 { ++ reg = <0>; ++ label = "port1"; ++ }; ++ ++ port@1 { ++ reg = <1>; ++ label = "port2"; ++ }; ++ ++ port@2 { ++ reg = <2>; ++ label = "port3"; ++ }; ++ ++ port@3 { ++ reg = <3>; ++ label = "port4"; ++ }; ++ ++ port@5 { ++ reg = <5>; ++ phy-mode = "rgmii-id"; ++ ethernet = <ð0port>; ++ ++ fixed-link { ++ speed = <1000>; ++ full-duplex; ++ }; ++ }; ++ }; ++ }; ++}; ++ ++&nand { ++ status = "okay"; ++ pinctrl-0 = <&pmx_nand>; ++ pinctrl-names = "default"; ++ ++ partition@0 { ++ label = "u-boot"; ++ reg = <0x00000000 0x000a0000>; ++ read-only; ++ }; ++ ++ partition@a0000 { ++ label = "u-boot-env"; ++ reg = <0x000a0000 0x00060000>; ++ read-only; ++ }; ++ ++ partition@100000 { ++ label = "kernel"; ++ reg = <0x00100000 0x00400000>; ++ }; ++ ++ partition@500000 { ++ label = "ubi"; ++ reg = <0x00500000 0x1fb00000>; ++ }; ++}; ++ ++&pciec { ++ status = "okay"; ++}; ++ ++&pcie0 { ++ status = "okay"; ++}; ++ ++&pinctrl { ++ pinctrl-0 = <&pmx_sysrst>; ++ pinctrl-names = "default"; ++ ++ pmx_sysrst: pmx-sysrst { ++ marvell,pins = "mpp6"; ++ marvell,function = "sysrst"; ++ }; ++ ++ pmx_sdio_cd: pmx-sdio-cd { ++ marvell,pins = "mpp28"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led: pmx-led { ++ marvell,pins = "mpp34", "mpp35", "mpp49"; ++ marvell,function = "gpio"; ++ }; ++}; ++ ++&rtc { ++ status = "okay"; ++}; ++ ++&sata_phy0 { ++ status = "disabled"; ++}; ++ ++&sata_phy1 { ++ status = "disabled"; ++}; ++ ++&sdio { ++ pinctrl-0 = <&pmx_sdio_cd>; ++ pinctrl-names = "default"; ++ status = "okay"; ++ cd-gpios = <&gpio0 28 9>; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; ++ ++&usb0 { ++ status = "okay"; ++}; diff --git a/target/linux/kirkwood/patches-6.1/100-ib62x0.patch b/target/linux/kirkwood/patches-6.1/100-ib62x0.patch new file mode 100644 index 0000000000..0637c24b63 --- /dev/null +++ b/target/linux/kirkwood/patches-6.1/100-ib62x0.patch @@ -0,0 +1,53 @@ +--- a/arch/arm/boot/dts/kirkwood-ib62x0.dts ++++ b/arch/arm/boot/dts/kirkwood-ib62x0.dts +@@ -6,7 +6,14 @@ + + / { + model = "RaidSonic ICY BOX IB-NAS62x0 (Rev B)"; +- compatible = "raidsonic,ib-nas6210-b", "raidsonic,ib-nas6220-b", "raidsonic,ib-nas6210", "raidsonic,ib-nas6220", "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood"; ++ compatible = "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood"; ++ ++ aliases { ++ led-boot = &led_green_os; ++ led-failsafe = &led_red_os; ++ led-running = &led_green_os; ++ led-upgrade = &led_red_os; ++ }; + + memory { + device_type = "memory"; +@@ -81,12 +88,12 @@ + &pmx_led_usb_transfer>; + pinctrl-names = "default"; + +- green-os { ++ led_green_os: green-os { + label = "ib62x0:green:os"; + gpios = <&gpio0 25 GPIO_ACTIVE_HIGH>; +- default-state = "keep"; ++ default-state = "on"; + }; +- red-os { ++ led_red_os: red-os { + label = "ib62x0:red:os"; + gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; + }; +@@ -118,13 +125,13 @@ + }; + + partition@100000 { +- label = "uImage"; +- reg = <0x0100000 0x600000>; ++ label = "second stage u-boot"; ++ reg = <0x100000 0x200000>; + }; + +- partition@700000 { +- label = "root"; +- reg = <0x0700000 0xf900000>; ++ partition@200000 { ++ label = "ubi"; ++ reg = <0x200000 0xfe00000>; + }; + + }; diff --git a/target/linux/kirkwood/patches-6.1/101-iconnect.patch b/target/linux/kirkwood/patches-6.1/101-iconnect.patch new file mode 100644 index 0000000000..935e2dfcf5 --- /dev/null +++ b/target/linux/kirkwood/patches-6.1/101-iconnect.patch @@ -0,0 +1,80 @@ +--- a/arch/arm/boot/dts/kirkwood-iconnect.dts ++++ b/arch/arm/boot/dts/kirkwood-iconnect.dts +@@ -8,6 +8,13 @@ + model = "Iomega Iconnect"; + compatible = "iom,iconnect-1.1", "iom,iconnect", "marvell,kirkwood-88f6281", "marvell,kirkwood"; + ++ aliases { ++ led-boot = &led_power_blue; ++ led-failsafe = &led_power_red; ++ led-running = &led_power_blue; ++ led-upgrade = &led_power_red; ++ }; ++ + memory { + device_type = "memory"; + reg = <0x00000000 0x10000000>; +@@ -16,8 +23,6 @@ + chosen { + bootargs = "console=ttyS0,115200n8 earlyprintk"; + stdout-path = &uart0; +- linux,initrd-start = <0x4500040>; +- linux,initrd-end = <0x4800000>; + }; + + ocp@f1000000 { +@@ -89,12 +94,12 @@ + gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; +- power-blue { ++ led_power_blue: power-blue { + label = "power:blue"; + gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; +- default-state = "keep"; ++ default-state = "on"; + }; +- power-red { ++ led_power_red: power-red { + label = "power:red"; + gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>; + }; +@@ -146,28 +151,23 @@ + status = "okay"; + + partition@0 { +- label = "uboot"; +- reg = <0x0000000 0xc0000>; ++ label = "u-boot"; ++ reg = <0x0000000 0xe0000>; + }; + +- partition@a0000 { +- label = "env"; +- reg = <0xa0000 0x20000>; ++ partition@e0000 { ++ label = "u-boot environment"; ++ reg = <0xe0000 0x100000>; + }; + + partition@100000 { +- label = "zImage"; +- reg = <0x100000 0x300000>; +- }; +- +- partition@540000 { +- label = "initrd"; +- reg = <0x540000 0x300000>; ++ label = "second stage u-boot"; ++ reg = <0x100000 0x200000>; + }; + +- partition@980000 { +- label = "boot"; +- reg = <0x980000 0x1f400000>; ++ partition@200000 { ++ label = "ubi"; ++ reg = <0x200000 0x1fe00000>; + }; + }; + diff --git a/target/linux/kirkwood/patches-6.1/102-dockstar.patch b/target/linux/kirkwood/patches-6.1/102-dockstar.patch new file mode 100644 index 0000000000..127f84962c --- /dev/null +++ b/target/linux/kirkwood/patches-6.1/102-dockstar.patch @@ -0,0 +1,62 @@ +--- a/arch/arm/boot/dts/kirkwood-dockstar.dts ++++ b/arch/arm/boot/dts/kirkwood-dockstar.dts +@@ -8,6 +8,13 @@ + model = "Seagate FreeAgent Dockstar"; + compatible = "seagate,dockstar", "marvell,kirkwood-88f6281", "marvell,kirkwood"; + ++ aliases { ++ led-boot = &led_health; ++ led-failsafe = &led_fault; ++ led-running = &led_health; ++ led-upgrade = &led_fault; ++ }; ++ + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; +@@ -42,12 +49,12 @@ + pinctrl-0 = <&pmx_led_green &pmx_led_orange>; + pinctrl-names = "default"; + +- health { ++ led_health: health { + label = "status:green:health"; + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; +- default-state = "keep"; ++ default-state = "on"; + }; +- fault { ++ led_fault: fault { + label = "status:orange:fault"; + gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; +@@ -78,18 +85,22 @@ + + partition@0 { + label = "u-boot"; +- reg = <0x0000000 0x100000>; +- read-only; ++ reg = <0x0000000 0xe0000>; ++ }; ++ ++ partition@e0000 { ++ label = "u-boot environment"; ++ reg = <0xe0000 0x100000>; + }; + + partition@100000 { +- label = "uImage"; +- reg = <0x0100000 0x400000>; ++ label = "second stage u-boot"; ++ reg = <0x100000 0x200000>; + }; + +- partition@500000 { +- label = "data"; +- reg = <0x0500000 0xfb00000>; ++ partition@200000 { ++ label = "ubi"; ++ reg = <0x200000 0xfe00000>; + }; + }; + diff --git a/target/linux/kirkwood/patches-6.1/103-iomega-ix2-200.patch b/target/linux/kirkwood/patches-6.1/103-iomega-ix2-200.patch new file mode 100644 index 0000000000..9313b4bc3e --- /dev/null +++ b/target/linux/kirkwood/patches-6.1/103-iomega-ix2-200.patch @@ -0,0 +1,67 @@ +--- a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts ++++ b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts +@@ -8,6 +8,13 @@ + model = "Iomega StorCenter ix2-200"; + compatible = "iom,ix2-200", "marvell,kirkwood-88f6281", "marvell,kirkwood"; + ++ aliases { ++ led-boot = &led_power; ++ led-failsafe = &led_health; ++ led-running = &led_power; ++ led-upgrade = &led_health; ++ }; ++ + memory { + device_type = "memory"; + reg = <0x00000000 0x10000000>; +@@ -127,16 +134,16 @@ + &pmx_led_rebuild &pmx_led_health >; + pinctrl-names = "default"; + +- power_led { ++ led_power: power_led { + label = "status:white:power_led"; + gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>; +- default-state = "keep"; ++ default-state = "on"; + }; + rebuild_led { + label = "status:white:rebuild_led"; + gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; + }; +- health_led { ++ led_health: health_led { + label = "status:red:health_led"; + gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; + }; +@@ -186,18 +193,18 @@ + }; + + partition@a0000 { +- label = "env"; ++ label = "u-boot environment"; + reg = <0xa0000 0x20000>; + read-only; + }; + + partition@100000 { +- label = "uImage"; ++ label = "kernel"; + reg = <0x100000 0x300000>; + }; + + partition@400000 { +- label = "rootfs"; ++ label = "ubi"; + reg = <0x400000 0x1C00000>; + }; + }; +@@ -211,7 +218,7 @@ + }; + + ð0 { +- status = "okay"; ++ status = "disabled"; + ethernet0-port@0 { + speed = <1000>; + duplex = <1>; diff --git a/target/linux/kirkwood/patches-6.1/105-linksys-viper-dts.patch b/target/linux/kirkwood/patches-6.1/105-linksys-viper-dts.patch new file mode 100644 index 0000000000..d56a469d94 --- /dev/null +++ b/target/linux/kirkwood/patches-6.1/105-linksys-viper-dts.patch @@ -0,0 +1,59 @@ +--- a/arch/arm/boot/dts/kirkwood-linksys-viper.dts ++++ b/arch/arm/boot/dts/kirkwood-linksys-viper.dts +@@ -24,6 +24,10 @@ + }; + + aliases { ++ led-boot = &led_white_health; ++ led-failsafe = &led_white_health; ++ led-running = &led_white_health; ++ led-upgrade = &led_white_health; + serial0 = &uart0; + }; + +@@ -56,9 +60,10 @@ + pinctrl-0 = < &pmx_led_white_health &pmx_led_white_pulse >; + pinctrl-names = "default"; + +- white-health { ++ led_white_health: white-health { + label = "viper:white:health"; + gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; ++ default-state = "on"; + }; + + white-pulse { +@@ -114,23 +119,23 @@ + }; + + partition@200000 { +- label = "kernel"; +- reg = <0x200000 0x2A0000>; ++ label = "kernel1"; ++ reg = <0x200000 0x1A00000>; + }; + +- partition@4a0000 { +- label = "rootfs"; +- reg = <0x4A0000 0x1760000>; ++ partition@500000 { ++ label = "rootfs1"; ++ reg = <0x500000 0x1700000>; + }; + + partition@1c00000 { +- label = "alt_kernel"; +- reg = <0x1C00000 0x2A0000>; ++ label = "kernel2"; ++ reg = <0x1C00000 0x1A00000>; + }; + +- partition@1ea0000 { +- label = "alt_rootfs"; +- reg = <0x1EA0000 0x1760000>; ++ partition@1f00000 { ++ label = "rootfs2"; ++ reg = <0x1F00000 0x1700000>; + }; + + partition@3600000 { diff --git a/target/linux/kirkwood/patches-6.1/106-goflexnet.patch b/target/linux/kirkwood/patches-6.1/106-goflexnet.patch new file mode 100644 index 0000000000..82cf90841e --- /dev/null +++ b/target/linux/kirkwood/patches-6.1/106-goflexnet.patch @@ -0,0 +1,53 @@ +--- a/arch/arm/boot/dts/kirkwood-goflexnet.dts ++++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts +@@ -8,6 +8,13 @@ + model = "Seagate GoFlex Net"; + compatible = "seagate,goflexnet", "marvell,kirkwood-88f6281", "marvell,kirkwood"; + ++ aliases { ++ led-boot = &led_health; ++ led-failsafe = &led_fault; ++ led-running = &led_health; ++ led-upgrade = &led_fault; ++ }; ++ + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; +@@ -85,12 +92,12 @@ + >; + pinctrl-names = "default"; + +- health { ++ led_health: health { + label = "status:green:health"; + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; +- default-state = "keep"; ++ default-state = "on"; + }; +- fault { ++ led_fault: fault { + label = "status:orange:fault"; + gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; +@@ -159,18 +166,8 @@ + }; + + partition@100000 { +- label = "uImage"; +- reg = <0x0100000 0x400000>; +- }; +- +- partition@500000 { +- label = "pogoplug"; +- reg = <0x0500000 0x2000000>; +- }; +- +- partition@2500000 { +- label = "root"; +- reg = <0x02500000 0xd800000>; ++ label = "ubi"; ++ reg = <0x0100000 0x0ff00000>; + }; + }; + diff --git a/target/linux/kirkwood/patches-6.1/107-01-zyxel-nsa3x0-common-nand-partitions.patch b/target/linux/kirkwood/patches-6.1/107-01-zyxel-nsa3x0-common-nand-partitions.patch new file mode 100644 index 0000000000..df654033fd --- /dev/null +++ b/target/linux/kirkwood/patches-6.1/107-01-zyxel-nsa3x0-common-nand-partitions.patch @@ -0,0 +1,48 @@ +--- a/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi ++++ b/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi +@@ -112,40 +112,16 @@ + + partition@0 { + label = "uboot"; +- reg = <0x0000000 0x0100000>; ++ reg = <0x0000000 0x00c0000>; + read-only; + }; + partition@100000 { + label = "uboot_env"; +- reg = <0x0100000 0x0080000>; ++ reg = <0x00c0000 0x0080000>; + }; +- partition@180000 { +- label = "key_store"; +- reg = <0x0180000 0x0080000>; +- }; +- partition@200000 { +- label = "info"; +- reg = <0x0200000 0x0080000>; +- }; +- partition@280000 { +- label = "etc"; +- reg = <0x0280000 0x0a00000>; +- }; +- partition@c80000 { +- label = "kernel_1"; +- reg = <0x0c80000 0x0a00000>; +- }; +- partition@1680000 { +- label = "rootfs1"; +- reg = <0x1680000 0x2fc0000>; +- }; +- partition@4640000 { +- label = "kernel_2"; +- reg = <0x4640000 0x0a00000>; +- }; +- partition@5040000 { +- label = "rootfs2"; +- reg = <0x5040000 0x2fc0000>; ++ partition@140000 { ++ label = "ubi"; ++ reg = <0x0140000 0x7ec0000>; + }; + }; + diff --git a/target/linux/kirkwood/patches-6.1/107-03-nsa325.patch b/target/linux/kirkwood/patches-6.1/107-03-nsa325.patch new file mode 100644 index 0000000000..374c0895a9 --- /dev/null +++ b/target/linux/kirkwood/patches-6.1/107-03-nsa325.patch @@ -0,0 +1,54 @@ +--- a/arch/arm/boot/dts/kirkwood-nsa325.dts ++++ b/arch/arm/boot/dts/kirkwood-nsa325.dts +@@ -15,6 +15,13 @@ + model = "ZyXEL NSA325"; + compatible = "zyxel,nsa325", "marvell,kirkwood-88f6282", "marvell,kirkwood"; + ++ aliases { ++ led-boot = &led_green_sys; ++ led-failsafe = &led_orange_sys; ++ led-running = &led_green_sys; ++ led-upgrade = &led_orange_sys; ++ }; ++ + memory { + device_type = "memory"; + reg = <0x00000000 0x20000000>; +@@ -162,17 +169,19 @@ + &pmx_led_hdd1_green &pmx_led_hdd1_red>; + pinctrl-names = "default"; + +- green-sys { ++ led_green_sys: green-sys { + label = "nsa325:green:sys"; + gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; ++ default-state = "on"; + }; +- orange-sys { ++ led_orange_sys: orange-sys { + label = "nsa325:orange:sys"; + gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; + }; + green-hdd1 { + label = "nsa325:green:hdd1"; + gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; ++ linux,default-trigger = "ata1"; + }; + red-hdd1 { + label = "nsa325:red:hdd1"; +@@ -181,6 +190,7 @@ + green-hdd2 { + label = "nsa325:green:hdd2"; + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; ++ linux,default-trigger = "ata2"; + }; + red-hdd2 { + label = "nsa325:red:hdd2"; +@@ -189,6 +199,7 @@ + green-usb { + label = "nsa325:green:usb"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; ++ linux,default-trigger = "usb-host"; + }; + green-copy { + label = "nsa325:green:copy"; diff --git a/target/linux/kirkwood/patches-6.1/109-pogoplug_v4.patch b/target/linux/kirkwood/patches-6.1/109-pogoplug_v4.patch new file mode 100644 index 0000000000..4273eb9af1 --- /dev/null +++ b/target/linux/kirkwood/patches-6.1/109-pogoplug_v4.patch @@ -0,0 +1,87 @@ +--- a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts ++++ b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts +@@ -18,12 +18,20 @@ + compatible = "cloudengines,pogoplugv4", "marvell,kirkwood-88f6192", + "marvell,kirkwood"; + ++ aliases { ++ led-boot = &led_health; ++ led-failsafe = &led_fault; ++ led-running = &led_health; ++ led-upgrade = &led_fault; ++ }; ++ + memory { + device_type = "memory"; + reg = <0x00000000 0x08000000>; + }; + + chosen { ++ bootargs = "console=ttyS0,115200"; + stdout-path = "uart0:115200n8"; + }; + +@@ -37,8 +45,8 @@ + eject { + debounce-interval = <50>; + wakeup-source; +- linux,code = ; +- label = "Eject Button"; ++ linux,code = ; ++ label = "Reset"; + gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; + }; + }; +@@ -48,12 +56,12 @@ + pinctrl-0 = <&pmx_led_green &pmx_led_red>; + pinctrl-names = "default"; + +- health { ++ led_health: health { + label = "pogoplugv4:green:health"; + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; +- fault { ++ led_fault: fault { + label = "pogoplugv4:red:fault"; + gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; + }; +@@ -137,29 +145,19 @@ + #size-cells = <1>; + + partition@0 { +- label = "u-boot"; +- reg = <0x00000000 0x200000>; ++ label = "uboot"; ++ reg = <0x00000000 0x1c0000>; + read-only; + }; + +- partition@200000 { +- label = "uImage"; +- reg = <0x00200000 0x300000>; +- }; +- +- partition@500000 { +- label = "uImage2"; +- reg = <0x00500000 0x300000>; +- }; +- +- partition@800000 { +- label = "failsafe"; +- reg = <0x00800000 0x800000>; ++ partition@1c0000 { ++ label = "uboot_env"; ++ reg = <0x001c0000 0x40000>; + }; + +- partition@1000000 { +- label = "root"; +- reg = <0x01000000 0x7000000>; ++ partition@200000 { ++ label = "ubi"; ++ reg = <0x00200000 0x7e00000>; + }; + }; + }; diff --git a/target/linux/kirkwood/patches-6.1/110-pogo_e02.patch b/target/linux/kirkwood/patches-6.1/110-pogo_e02.patch new file mode 100644 index 0000000000..fc384d3521 --- /dev/null +++ b/target/linux/kirkwood/patches-6.1/110-pogo_e02.patch @@ -0,0 +1,68 @@ +--- a/arch/arm/boot/dts/kirkwood-pogo_e02.dts ++++ b/arch/arm/boot/dts/kirkwood-pogo_e02.dts +@@ -20,6 +20,13 @@ + compatible = "cloudengines,pogoe02", "marvell,kirkwood-88f6281", + "marvell,kirkwood"; + ++ aliases { ++ led-boot = &led_health; ++ led-failsafe = &led_fault; ++ led-running = &led_health; ++ led-upgrade = &led_fault; ++ }; ++ + memory { + device_type = "memory"; + reg = <0x00000000 0x10000000>; +@@ -33,12 +40,12 @@ + gpio-leds { + compatible = "gpio-leds"; + +- health { ++ led_health: health { + label = "pogo_e02:green:health"; + gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; +- default-state = "keep"; ++ default-state = "on"; + }; +- fault { ++ led_fault: fault { + label = "pogo_e02:orange:fault"; + gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; + }; +@@ -95,24 +102,24 @@ + status = "okay"; + + partition@0 { +- label = "u-boot"; +- reg = <0x0000000 0x100000>; ++ label = "uboot"; ++ reg = <0x0 0xe0000>; + read-only; + }; + +- partition@100000 { +- label = "uImage"; +- reg = <0x0100000 0x400000>; ++ partition@e0000 { ++ label = "uboot_env"; ++ reg = <0xe0000 0x20000>; + }; + +- partition@500000 { +- label = "pogoplug"; +- reg = <0x0500000 0x2000000>; ++ partition@100000 { ++ label = "second_stage_uboot"; ++ reg = <0x100000 0x100000>; + }; + +- partition@2500000 { +- label = "root"; +- reg = <0x02500000 0x5b00000>; ++ partition@200000 { ++ label = "ubi"; ++ reg = <0x200000 0x7e00000>; + }; + }; + diff --git a/target/linux/kirkwood/patches-6.1/111-l-50.patch b/target/linux/kirkwood/patches-6.1/111-l-50.patch new file mode 100644 index 0000000000..bc933cb610 --- /dev/null +++ b/target/linux/kirkwood/patches-6.1/111-l-50.patch @@ -0,0 +1,47 @@ +--- a/arch/arm/boot/dts/kirkwood-l-50.dts ++++ b/arch/arm/boot/dts/kirkwood-l-50.dts +@@ -18,6 +18,13 @@ + reg = <0x00000000 0x20000000>; + }; + ++ aliases { ++ led-boot = &led_status_green; ++ led-failsafe = &led_status_red; ++ led-running = &led_status_green; ++ led-upgrade = &led_status_red; ++ }; ++ + chosen { + bootargs = "console=ttyS0,115200n8"; + stdout-path = &uart0; +@@ -95,12 +102,12 @@ + leds { + compatible = "gpio-leds"; + +- status_green { ++ led_status_green: status_green { + label = "l-50:green:status"; + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + }; + +- status_red { ++ led_status_red: status_red { + label = "l-50:red:status"; + gpios = <&gpio3 2 GPIO_ACTIVE_LOW>; + }; +@@ -349,13 +356,8 @@ + }; + + partition@100000 { +- label = "kernel-1"; +- reg = <0x00100000 0x00800000>; +- }; +- +- partition@900000 { +- label = "rootfs-1"; +- reg = <0x00900000 0x07100000>; ++ label = "ubi"; ++ reg = <0x00100000 0x07900000>; + }; + + partition@7a00000 { diff --git a/target/linux/kirkwood/patches-6.1/112-sheevaplug.patch b/target/linux/kirkwood/patches-6.1/112-sheevaplug.patch new file mode 100644 index 0000000000..d1ff9884a0 --- /dev/null +++ b/target/linux/kirkwood/patches-6.1/112-sheevaplug.patch @@ -0,0 +1,47 @@ +--- a/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi ++++ b/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi +@@ -78,13 +78,8 @@ + }; + + partition@100000 { +- label = "uImage"; +- reg = <0x0100000 0x400000>; +- }; +- +- partition@500000 { +- label = "root"; +- reg = <0x0500000 0x1fb00000>; ++ label = "ubi"; ++ reg = <0x0100000 0x1ff00000>; + }; + }; + +--- a/arch/arm/boot/dts/kirkwood-sheevaplug.dts ++++ b/arch/arm/boot/dts/kirkwood-sheevaplug.dts +@@ -13,6 +13,13 @@ + model = "Globalscale Technologies SheevaPlug"; + compatible = "globalscale,sheevaplug", "marvell,kirkwood-88f6281", "marvell,kirkwood"; + ++ aliases { ++ led-boot = &led_health; ++ led-failsafe = &led_health; ++ led-running = &led_health; ++ led-upgrade = &led_health; ++ }; ++ + ocp@f1000000 { + mvsdio@90000 { + pinctrl-0 = <&pmx_sdio>; +@@ -28,10 +35,10 @@ + pinctrl-0 = <&pmx_led_blue &pmx_led_red>; + pinctrl-names = "default"; + +- health { ++ led_health: health { + label = "sheevaplug:blue:health"; + gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; +- default-state = "keep"; ++ default-state = "on"; + }; + + misc { diff --git a/target/linux/kirkwood/patches-6.1/113-readynas_duo_v2.patch b/target/linux/kirkwood/patches-6.1/113-readynas_duo_v2.patch new file mode 100644 index 0000000000..c6452c55a3 --- /dev/null +++ b/target/linux/kirkwood/patches-6.1/113-readynas_duo_v2.patch @@ -0,0 +1,76 @@ +--- a/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts ++++ b/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts +@@ -19,6 +19,13 @@ + reg = <0x00000000 0x10000000>; + }; + ++ aliases { ++ led-boot = &led_power; ++ led-failsafe = &led_power; ++ led-running = &led_power; ++ led-upgrade = &led_power; ++ }; ++ + chosen { + bootargs = "console=ttyS0,115200n8 earlyprintk"; + stdout-path = &uart0; +@@ -115,7 +122,7 @@ + &pmx_led_blue_backup >; + pinctrl-names = "default"; + +- power_led { ++ led_power: power_led { + label = "status:blue:power_led"; + gpios = <&gpio0 31 GPIO_ACTIVE_LOW>; + default-state = "keep"; +@@ -129,11 +136,13 @@ + disk1_led { + label = "status:blue:disk1_led"; + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; ++ linux,default-trigger = "ata1"; + }; + + disk2_led { + label = "status:blue:disk2_led"; + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; ++ linux,default-trigger = "ata2"; + }; + + backup_led { +@@ -150,7 +159,13 @@ + + power-button { + label = "Power Button"; +- linux,code = ; ++ /* Power button and INT pin from PHY are both connected ++ * to this GPIO. Every network restart causes PHY restart ++ * and button is pressed. It's difficult to use it as ++ * KEY_POWER without changes in kernel (or netifd) so ++ * the button is configured as regular one. ++ */ ++ linux,code = ; + gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; + +@@ -208,18 +223,13 @@ + }; + + partition@200000 { +- label = "uImage"; ++ label = "kernel"; + reg = <0x0200000 0x600000>; + }; + + partition@800000 { +- label = "minirootfs"; +- reg = <0x0800000 0x1000000>; +- }; +- +- partition@1800000 { +- label = "jffs2"; +- reg = <0x1800000 0x6800000>; ++ label = "ubi"; ++ reg = <0x0800000 0x7800000>; + }; + }; + diff --git a/target/linux/kirkwood/patches-6.1/114-ctera-c-200-v1.patch b/target/linux/kirkwood/patches-6.1/114-ctera-c-200-v1.patch new file mode 100644 index 0000000000..23922b8d88 --- /dev/null +++ b/target/linux/kirkwood/patches-6.1/114-ctera-c-200-v1.patch @@ -0,0 +1,51 @@ +--- a/arch/arm/boot/dts/kirkwood-c200-v1.dts ++++ b/arch/arm/boot/dts/kirkwood-c200-v1.dts +@@ -14,6 +14,14 @@ + model = "Ctera C200 V1"; + compatible = "ctera,c200-v1", "marvell,kirkwood-88f6281", "marvell,kirkwood"; + ++ ++ aliases { ++ led-boot = &led_status_green; ++ led-failsafe = &led_status_red; ++ led-running = &led_status_green; ++ led-upgrade = &led_status_red; ++ }; ++ + chosen { + bootargs = "console=ttyS0,115200"; + stdout-path = &uart0; +@@ -78,6 +86,7 @@ + function-enumerator = <1>; + color = ; + gpios = <&gpio0 15 GPIO_ACTIVE_LOW>; ++ linux,default-trigger = "ata1"; + }; + + led-2 { +@@ -85,6 +94,7 @@ + function-enumerator = <2>; + color = ; + gpios = <&gpio0 16 GPIO_ACTIVE_LOW>; ++ linux,default-trigger = "ata2"; + }; + + led-3 { +@@ -94,13 +104,15 @@ + gpios = <&gpio0 17 GPIO_ACTIVE_LOW>; + }; + +- led-4 { ++ led_status_red: led-4 { ++ label = "red:status"; + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + }; + +- led-5 { ++ led_status_green: led-5 { ++ label = "green:status"; + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; diff --git a/target/linux/kirkwood/patches-6.1/115-nsa310s.patch b/target/linux/kirkwood/patches-6.1/115-nsa310s.patch new file mode 100644 index 0000000000..4c6e08f49c --- /dev/null +++ b/target/linux/kirkwood/patches-6.1/115-nsa310s.patch @@ -0,0 +1,35 @@ +--- a/arch/arm/boot/dts/kirkwood-nsa310s.dts ++++ b/arch/arm/boot/dts/kirkwood-nsa310s.dts +@@ -16,6 +16,13 @@ + model = "ZyXEL NSA310S"; + compatible = "zyxel,nsa310s", "marvell,kirkwood-88f6702", "marvell,kirkwood"; + ++ aliases { ++ led-boot = &led_green_sys; ++ led-failsafe = &led_red_sys; ++ led-running = &led_green_sys; ++ led-upgrade = &led_red_sys; ++ }; ++ + memory { + device_type = "memory"; + reg = <0x00000000 0x10000000>; +@@ -96,14 +103,16 @@ + gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>; + }; + +- led-6 { ++ led_green_sys: led-6 { ++ label = "nsa310s:green:sys"; + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-on"; + }; + +- led-7 { ++ led_red_sys: led-7 { ++ label = "nsa310s:red:sys"; + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; diff --git a/target/linux/kirkwood/patches-6.1/116-4i-edge-200.patch b/target/linux/kirkwood/patches-6.1/116-4i-edge-200.patch new file mode 100644 index 0000000000..ffc46c29dc --- /dev/null +++ b/target/linux/kirkwood/patches-6.1/116-4i-edge-200.patch @@ -0,0 +1,34 @@ +--- a/arch/arm/boot/dts/kirkwood-4i-edge-200.dts ++++ b/arch/arm/boot/dts/kirkwood-4i-edge-200.dts +@@ -20,6 +20,13 @@ + reg = <0x00000000 0x20000000>; + }; + ++ aliases { ++ led-boot = &led_status_green; ++ led-failsafe = &led_status_orange; ++ led-running = &led_status_green; ++ led-upgrade = &led_status_orange; ++ }; ++ + chosen { + bootargs = "console=ttyS0,115200n8"; + stdout-path = &uart0; +@@ -37,13 +44,15 @@ + linux,default-trigger = "mmc0"; + }; + +- led-2 { ++ led_status_orange: led-2 { ++ label = "orange:status"; + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; + }; + +- led-3 { ++ led_status_green: led-3 { ++ label = "green:status"; + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>; diff --git a/target/linux/kirkwood/patches-6.1/201-enable-sata-port-specific-led-triggers.patch b/target/linux/kirkwood/patches-6.1/201-enable-sata-port-specific-led-triggers.patch new file mode 100644 index 0000000000..35db065727 --- /dev/null +++ b/target/linux/kirkwood/patches-6.1/201-enable-sata-port-specific-led-triggers.patch @@ -0,0 +1,10 @@ +--- a/arch/arm/mach-mvebu/Kconfig ++++ b/arch/arm/mach-mvebu/Kconfig +@@ -116,6 +116,7 @@ config MACH_DOVE + config MACH_KIRKWOOD + bool "Marvell Kirkwood boards" + depends on ARCH_MULTI_V5 ++ select ARCH_WANT_LIBATA_LEDS + select CPU_FEROCEON + select GPIOLIB + select KIRKWOOD_CLK diff --git a/target/linux/kirkwood/patches-6.1/202-linksys-find-active-root.patch b/target/linux/kirkwood/patches-6.1/202-linksys-find-active-root.patch new file mode 100644 index 0000000000..515bb21707 --- /dev/null +++ b/target/linux/kirkwood/patches-6.1/202-linksys-find-active-root.patch @@ -0,0 +1,62 @@ +The WRT1900AC among other Linksys routers uses a dual-firmware layout. +Dynamically rename the active partition to "ubi". + +Signed-off-by: Imre Kaloz +--- +--- a/drivers/mtd/parsers/ofpart_core.c ++++ b/drivers/mtd/parsers/ofpart_core.c +@@ -38,6 +38,8 @@ static bool node_has_compatible(struct d + return of_get_property(pp, "compatible", NULL); + } + ++static int mangled_rootblock; ++ + static int parse_fixed_partitions(struct mtd_info *master, + const struct mtd_partition **pparts, + struct mtd_part_parser_data *data) +@@ -47,6 +49,7 @@ static int parse_fixed_partitions(struct + struct mtd_partition *parts; + struct device_node *mtd_node; + struct device_node *ofpart_node; ++ const char *owrtpart = "ubi"; + const char *partname; + struct device_node *pp; + int nr_parts, i, ret = 0; +@@ -133,9 +136,15 @@ static int parse_fixed_partitions(struct + parts[i].size = of_read_number(reg + a_cells, s_cells); + parts[i].of_node = pp; + +- partname = of_get_property(pp, "label", &len); +- if (!partname) +- partname = of_get_property(pp, "name", &len); ++ if (mangled_rootblock && (i == mangled_rootblock)) { ++ partname = owrtpart; ++ } else { ++ partname = of_get_property(pp, "label", &len); ++ ++ if (!partname) ++ partname = of_get_property(pp, "name", &len); ++ } ++ + parts[i].name = partname; + + if (of_get_property(pp, "read-only", &len)) +@@ -252,6 +261,18 @@ static int __init ofpart_parser_init(voi + return 0; + } + ++static int __init active_root(char *str) ++{ ++ get_option(&str, &mangled_rootblock); ++ ++ if (!mangled_rootblock) ++ return 1; ++ ++ return 1; ++} ++ ++__setup("mangled_rootblock=", active_root); ++ + static void __exit ofpart_parser_exit(void) + { + deregister_mtd_parser(&ofpart_parser); diff --git a/target/linux/kirkwood/patches-6.1/203-blackarmor-nas220.patch b/target/linux/kirkwood/patches-6.1/203-blackarmor-nas220.patch new file mode 100644 index 0000000000..e04a28206a --- /dev/null +++ b/target/linux/kirkwood/patches-6.1/203-blackarmor-nas220.patch @@ -0,0 +1,99 @@ +--- a/arch/arm/boot/dts/kirkwood-blackarmor-nas220.dts ++++ b/arch/arm/boot/dts/kirkwood-blackarmor-nas220.dts +@@ -17,6 +17,13 @@ + compatible = "seagate,blackarmor-nas220","marvell,kirkwood-88f6192", + "marvell,kirkwood"; + ++ aliases { ++ led-boot = &led_status_amber; ++ led-failsafe = &led_status_amber; ++ led-running = &led_status_blue; ++ led-upgrade = &led_status_amber; ++ }; ++ + memory { /* 128 MB */ + device_type = "memory"; + reg = <0x00000000 0x8000000>; +@@ -36,14 +43,14 @@ + compatible = "gpio-keys"; + + reset { +- label = "Reset"; +- linux,code = ; ++ label = "Reset Button"; ++ linux,code = ; + gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; + }; + +- button { +- label = "Power"; +- linux,code = ; ++ power { ++ label = "Power Button"; ++ linux,code = ; + gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; + }; + }; +@@ -51,11 +58,27 @@ + gpio-leds { + compatible = "gpio-leds"; + +- blue-power { ++ led_power_blue: power_blue { + label = "nas220:blue:power"; + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-on"; + }; ++ ++ disk_blue { ++ label = "nas220:blue:disk"; ++ gpios = <&gpio0 16 GPIO_ACTIVE_LOW>; ++ linux,default-trigger = "disk-activity"; ++ }; ++ ++ led_status_blue: status_blue { ++ label = "nas220:blue:status"; ++ gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ led_status_amber: status_amber { ++ label = "nas220:amber:status"; ++ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; ++ }; + }; + + regulators { +@@ -153,6 +176,33 @@ + + &nand { + status = "okay"; ++ ++ partitions { ++ compatible = "fixed-partitions"; ++ ++ partition@0 { ++ label = "uboot"; ++ reg = <0x0 0xa0000>; ++ read-only; ++ }; ++ ++ partition@a0000 { ++ label = "uboot-env"; ++ reg = <0xa0000 0x10000>; ++ read-only; ++ }; ++ ++ partition@b0000 { ++ label = "reserved"; ++ reg = <0xb0000 0x10000>; ++ read-only; ++ }; ++ ++ partition@c0000 { ++ label = "ubi"; ++ reg = <0xc0000 0x1e80000>; ++ }; ++ }; + }; + + &mdio {