From: Connor Yoon Date: Tue, 19 Mar 2024 13:10:51 +0000 (+0100) Subject: ipq807x: add Spectrum SAX1V1K X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=3569b37b15c721513a0a5d4bd6d857be2523ec38;p=openwrt%2Fstaging%2Fansuel.git ipq807x: add Spectrum SAX1V1K Spectrum SAX1V1K is a AX WIFI router with 3 1G and 1 2.5G ports. The router is provided to Spectrum customers. It is OEM of Askey RT5010W https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923 It continues the original work by @MeisterLone to get this device supported. Specifications: ``` • CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz • RAM: 2048MB of DDR3 • Storage: 1024MB eMMC • Ethernet: 3x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081) • WLAN: • 2.4GHz: Qualcomm QCN5024 4x4 802.11b/g/n/ax 1174 Mbps PHY rate • 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate • LED: 1 gpio-controlled dual color led (blue/red) • Buttons: 1x reset • Power: 12V DC jack ``` Notes: ``` • This commit adds only single partition support, that means sysupgrade is upgrading the current rootfs partition. • Installation can be done by serial connection only. • A poulated serial header is onboard https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923/6 • RX/TX is working, u-boot bootwait is active, secure boot is enabled. ``` Installation Instructions: **Most part of the installation is performed from an initramfs image.** Boot initramfs : Using serial connection 1. Boot up the device and wait till it displays "VERIFY_IB: Success. verify IB ok" 2. Once that message appears, login with username 'root' password serial number of your router in uppercase. 3. Use vi to paste the 'open.sh' script from @MeisterLone github on your device https://github.com/MeisterLone/Askey-RT5010W-D187-REV6/blob/master/Patch/open.sh 4. chmod 755 open.sh 5. ./open.sh 6. Set your ip to 192.168.0.1 7. Run a TFTP server and host the initramfs image on the TFTP server and name it "recovery.img" 8. Reboot device. On boot it will try TFTP. Install OpenWrt from initramfs image: 1. Use SCP (or other way) to transfer OpenWrt factory image 2. Connect to device using SSH (on a LAN port) 3. Flash firmware: sysupgrade # sysupgrade -n -v /tmp/openwrt_sysupgrade.bin 4. Set U-boot env variable: bootcmd # fw_setenv bootcmd "run fix_uboot; run setup_and_boot" 5. Reboot the device # reboot 6. Once device is booted, residue of previous firmware will prevent openwrt to work properly. Factory Reset is MUST required # Once serial console is displaying to login, hold reset button for 10 sec 7. Now everything should be operational. Note: this PR adds only single partition support, that means sysupgrade is upgrading the current rootfs partition Signed-off-by: Connor Yoon --- diff --git a/package/boot/uboot-envtools/files/qualcommax_ipq807x b/package/boot/uboot-envtools/files/qualcommax_ipq807x index 86e7062cfc..312fdf8d87 100644 --- a/package/boot/uboot-envtools/files/qualcommax_ipq807x +++ b/package/boot/uboot-envtools/files/qualcommax_ipq807x @@ -56,6 +56,11 @@ qnap,301w) [ -n "$idx" ] && \ ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x20000" "0x20000" "1" ;; +spectrum,sax1v1k) + mmcpart="$(find_mmc_part 0:APPSBLENV)" + [ -n "$mmcpart" ] && \ + ubootenv_add_uci_config "$mmcpart" "0x0" "0x40000" "0x40000" "1" + ;; esac config_load ubootenv diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index 41c772c967..ced4ece692 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -46,6 +46,7 @@ ALLWIFIBOARDS:= \ prpl_haze \ qnap_301w \ redmi_ax6 \ + spectrum_sax1v1k \ wallys_dr40x9 \ xiaomi_ax3600 \ xiaomi_ax9000 \ @@ -165,6 +166,7 @@ $(eval $(call generate-ipq-wifi-package,netgear_wax630,Netgear WAX630)) $(eval $(call generate-ipq-wifi-package,qnap_301w,QNAP 301w)) $(eval $(call generate-ipq-wifi-package,prpl_haze,prpl Haze)) $(eval $(call generate-ipq-wifi-package,redmi_ax6,Redmi AX6)) +$(eval $(call generate-ipq-wifi-package,spectrum_sax1v1k,Spectrum SAX1V1K)) $(eval $(call generate-ipq-wifi-package,wallys_dr40x9,Wallys DR40X9)) $(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600)) $(eval $(call generate-ipq-wifi-package,xiaomi_ax9000,Xiaomi AX9000)) diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-sax1v1k.dts b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-sax1v1k.dts new file mode 100644 index 0000000000..01ac1c5fd6 --- /dev/null +++ b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-sax1v1k.dts @@ -0,0 +1,219 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; + +#include "ipq8074.dtsi" +#include "ipq8074-hk-cpu.dtsi" +#include "ipq8074-ess.dtsi" +#include +#include +#include + +/ { + model = "Spectrum SAX1V1K"; + compatible = "spectrum,sax1v1k", "qcom,ipq8074"; + + aliases { + led-boot = &led_system_red; + led-failsafe = &led_system_red; + led-running = &led_system_blue; + led-upgrade = &led_system_red; + serial0 = &blsp1_uart5; + /* Aliases as required by u-boot to patch MAC addresses */ + ethernet0 = &dp6_syn; + ethernet1 = &dp4; + ethernet2 = &dp3; + ethernet3 = &dp2; + label-mac-device = &dp6_syn; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 34 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_system_blue: system-blue { + gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_STATUS; + }; + + led_system_red: system-red { + gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_STATUS; + }; + }; +}; + +&tlmm { + mdio_pins: mdio-pins { + mdc { + pins = "gpio68"; + function = "mdc"; + drive-strength = <8>; + bias-pull-up; + }; + + mdio { + pins = "gpio69"; + function = "mdio"; + drive-strength = <8>; + bias-pull-up; + }; + }; +}; + +&blsp1_uart5 { + status = "okay"; +}; + +&prng { + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&crypto { + status = "okay"; +}; + +&qpic_bam { + status = "okay"; +}; + +&mdio { + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>; + status = "okay"; + + ethernet-phy-package@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "qcom,qca8075-package"; + reg = <0>; + + qcom,package-mode = "qsgmii"; + + qca8075_1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; + + qca8075_2: ethernet-phy@2 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <2>; + }; + + qca8075_3: ethernet-phy@3 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <3>; + }; + }; + + qca8081: ethernet-phy@28 { + compatible = "ethernet-phy-id004d.d101"; + reg = <28>; + reset-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>; + }; +}; + +&sdhc_1 { + /* Following same rule as QNAP 301W + * the emmc has a problem with the hs400 > hs200 speed switch. + * Therefore remove the mmc-hs400-1_8v property + */ + /delete-property/ mmc-hs400-1_8v; + mmc-hs200-1_8v; + mmc-ddr-1_8v; + vqmmc-supply = <&l11>; + status = "okay"; +}; + +&switch { + switch_lan_bmp = <(ESS_PORT2 | ESS_PORT3 | ESS_PORT4)>; /* lan port bitmap */ + switch_wan_bmp = ; /* wan port bitmap */ + switch_mac_mode = ; /* mac mode for uniphy instance0*/ + switch_mac_mode2 = ; /* mac mode for uniphy instance2*/ + status = "okay"; + + qcom,port_phyinfo { + port@2 { + port_id = <2>; + phy_address = <1>; + }; + + port@3 { + port_id = <3>; + phy_address = <2>; + }; + + port@4 { + port_id = <4>; + phy_address = <3>; + }; + + port@6 { + port_id = <6>; + phy_address = <28>; + port_mac_sel = "QGMAC_PORT"; + }; + }; +}; + +&edma { + status = "okay"; +}; + +&dp2 { + phy-mode = "qsgmii"; + phy-handle = <&qca8075_1>; + label = "lan3"; + status = "okay"; +}; + +&dp3 { + phy-mode = "qsgmii"; + phy-handle = <&qca8075_2>; + label = "lan2"; + status = "okay"; +}; + +&dp4 { + phy-mode = "qsgmii"; + phy-handle = <&qca8075_3>; + label = "lan1"; + status = "okay"; +}; + +&dp6_syn { + phy-handle = <&qca8081>; + label = "wan"; + status = "okay"; +}; + +&wifi { + qcom,ath11k-calibration-variant = "Spectrum-SAX1V1K"; + status = "okay"; +}; diff --git a/target/linux/qualcommax/image/ipq807x.mk b/target/linux/qualcommax/image/ipq807x.mk index 027278b63c..e32250d458 100644 --- a/target/linux/qualcommax/image/ipq807x.mk +++ b/target/linux/qualcommax/image/ipq807x.mk @@ -247,6 +247,18 @@ define Device/redmi_ax6 endef TARGET_DEVICES += redmi_ax6 +define Device/spectrum_sax1v1k + $(call Device/FitImage) + $(call Device/EmmcImage) + DEVICE_VENDOR := Spectrum + DEVICE_MODEL := SAX1V1K + DEVICE_DTS_CONFIG := config@rt5010w-d187-rev6 + SOC := ipq8072 + IMAGES := sysupgrade.bin + DEVICE_PACKAGES := ipq-wifi-spectrum_sax1v1k +endef +TARGET_DEVICES += spectrum_sax1v1k + define Device/xiaomi_ax3600 $(call Device/FitImage) $(call Device/UbiFit) diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network index 77c84d40fa..a6ec834785 100644 --- a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network +++ b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network @@ -27,6 +27,7 @@ ipq807x_setup_interfaces() linksys,mx4200v2|\ prpl,haze|\ redmi,ax6|\ + spectrum,sax1v1k|\ xiaomi,ax3600) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan" ;; diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata index f533bac48e..d0689d0db6 100644 --- a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata +++ b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata @@ -33,7 +33,8 @@ case "$FIRMWARE" in zyxel,nbg7815) caldata_extract "0:art" 0x1000 0x20000 ;; - prpl,haze) + prpl,haze|\ + spectrum,sax1v1k) caldata_extract_mmc "0:ART" 0x1000 0x20000 ;; esac diff --git a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh index 768bf649ce..b9668d0af4 100644 --- a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh +++ b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh @@ -92,7 +92,8 @@ platform_do_upgrade() { nand_do_upgrade "$1" ;; prpl,haze|\ - qnap,301w) + qnap,301w|\ + spectrum,sax1v1k) kernelname="0:HLOS" rootfsname="rootfs" mmc_do_upgrade "$1"