From: Ansuel Smith Date: Thu, 4 Nov 2021 20:56:41 +0000 (+0100) Subject: ipq806x: 5:15: copy config and patch from 5.10 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=3064e76c948570a6f0930e893d25a551449df8ff;p=openwrt%2Fstaging%2Fynezz.git ipq806x: 5:15: copy config and patch from 5.10 Copy config and patch from kernel 5.10 to kernel 5.15 Signed-off-by: Ansuel Smith --- diff --git a/target/linux/ipq806x/config-5.15 b/target/linux/ipq806x/config-5.15 new file mode 100644 index 0000000000..f2880b5d66 --- /dev/null +++ b/target/linux/ipq806x/config-5.15 @@ -0,0 +1,506 @@ +CONFIG_ALIGNMENT_TRAP=y +# CONFIG_APQ_GCC_8084 is not set +# CONFIG_APQ_MMCC_8084 is not set +CONFIG_AR8216_PHY=y +CONFIG_ARCH_32BIT_OFF_T=y +CONFIG_ARCH_HIBERNATION_POSSIBLE=y +# CONFIG_ARCH_IPQ40XX is not set +CONFIG_ARCH_KEEP_MEMBLOCK=y +# CONFIG_ARCH_MDM9615 is not set +CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y +CONFIG_ARCH_MSM8960=y +CONFIG_ARCH_MSM8974=y +CONFIG_ARCH_MSM8X60=y +CONFIG_ARCH_MULTIPLATFORM=y +CONFIG_ARCH_MULTI_V6_V7=y +CONFIG_ARCH_MULTI_V7=y +CONFIG_ARCH_NR_GPIO=0 +CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y +CONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT=y +CONFIG_ARCH_QCOM=y +CONFIG_ARCH_SELECT_MEMORY_MODEL=y +CONFIG_ARCH_SPARSEMEM_ENABLE=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_ARM=y +CONFIG_ARM_AMBA=y +CONFIG_ARM_APPENDED_DTB=y +CONFIG_ARM_ARCH_TIMER=y +CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y +CONFIG_ARM_ATAG_DTB_COMPAT=y +# CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER is not set +CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE=y +CONFIG_ARM_CPUIDLE=y +CONFIG_ARM_CPU_SUSPEND=y +# CONFIG_ARM_CPU_TOPOLOGY is not set +CONFIG_ARM_GIC=y +CONFIG_ARM_HAS_SG_CHAIN=y +CONFIG_ARM_L1_CACHE_SHIFT=6 +CONFIG_ARM_L1_CACHE_SHIFT_6=y +CONFIG_ARM_MODULE_PLTS=y +CONFIG_ARM_PATCH_IDIV=y +CONFIG_ARM_PATCH_PHYS_VIRT=y +# CONFIG_ARM_QCOM_CPUFREQ_HW is not set +CONFIG_ARM_QCOM_CPUFREQ_KRAIT=y +CONFIG_ARM_QCOM_CPUFREQ_NVMEM=y +CONFIG_ARM_QCOM_SPM_CPUIDLE=y +# CONFIG_ARM_SMMU is not set +CONFIG_ARM_THUMB=y +CONFIG_ARM_UNWIND=y +CONFIG_ARM_VIRT_EXT=y +CONFIG_AT803X_PHY=y +CONFIG_BINFMT_FLAT_ARGVP_ENVP_ON_STACK=y +CONFIG_BLK_DEV_LOOP=y +CONFIG_BLK_MQ_PCI=y +CONFIG_BOUNCE=y +# CONFIG_CACHE_L2X0 is not set +CONFIG_CLKDEV_LOOKUP=y +CONFIG_CLKSRC_QCOM=y +CONFIG_CLONE_BACKWARDS=y +CONFIG_CMDLINE_OVERRIDE=y +CONFIG_COMMON_CLK=y +CONFIG_COMMON_CLK_QCOM=y +CONFIG_COMPAT_32BIT_TIME=y +CONFIG_CPUFREQ_DT=y +CONFIG_CPUFREQ_DT_PLATDEV=y +CONFIG_CPU_32v6K=y +CONFIG_CPU_32v7=y +CONFIG_CPU_ABRT_EV7=y +CONFIG_CPU_CACHE_V7=y +CONFIG_CPU_CACHE_VIPT=y +CONFIG_CPU_COPY_V6=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y +CONFIG_CPU_FREQ=y +CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y +# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set +CONFIG_CPU_FREQ_GOV_ATTR_SET=y +CONFIG_CPU_FREQ_GOV_COMMON=y +# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set +CONFIG_CPU_FREQ_GOV_ONDEMAND=y +CONFIG_CPU_FREQ_GOV_PERFORMANCE=y +# CONFIG_CPU_FREQ_GOV_POWERSAVE is not set +CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y +# CONFIG_CPU_FREQ_GOV_USERSPACE is not set +CONFIG_CPU_FREQ_STAT=y +CONFIG_CPU_HAS_ASID=y +CONFIG_CPU_IDLE=y +CONFIG_CPU_IDLE_GOV_LADDER=y +CONFIG_CPU_IDLE_GOV_MENU=y +CONFIG_CPU_IDLE_MULTIPLE_DRIVERS=y +CONFIG_CPU_PABRT_V7=y +CONFIG_CPU_PM=y +CONFIG_CPU_RMAP=y +CONFIG_CPU_SPECTRE=y +CONFIG_CPU_THERMAL=y +CONFIG_CPU_THUMB_CAPABLE=y +CONFIG_CPU_TLB_V7=y +CONFIG_CPU_V7=y +CONFIG_CRC16=y +# CONFIG_CRC32_SARWATE is not set +CONFIG_CRC32_SLICEBY8=y +CONFIG_CRYPTO_ACOMP2=y +CONFIG_CRYPTO_AEAD=y +CONFIG_CRYPTO_AEAD2=y +CONFIG_CRYPTO_DEFLATE=y +CONFIG_CRYPTO_DEV_QCOM_RNG=y +CONFIG_CRYPTO_DRBG=y +CONFIG_CRYPTO_DRBG_HMAC=y +CONFIG_CRYPTO_DRBG_MENU=y +CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_HASH2=y +CONFIG_CRYPTO_HASH_INFO=y +CONFIG_CRYPTO_HMAC=y +CONFIG_CRYPTO_HW=y +CONFIG_CRYPTO_JITTERENTROPY=y +CONFIG_CRYPTO_LIB_SHA256=y +CONFIG_CRYPTO_LZO=y +CONFIG_CRYPTO_MANAGER=y +CONFIG_CRYPTO_MANAGER2=y +CONFIG_CRYPTO_NULL2=y +CONFIG_CRYPTO_RNG=y +CONFIG_CRYPTO_RNG2=y +CONFIG_CRYPTO_SHA256=y +CONFIG_CRYPTO_ZSTD=y +CONFIG_DCACHE_WORD_ACCESS=y +CONFIG_DEBUG_GPIO=y +CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S" +# CONFIG_DEVFREQ_GOV_PASSIVE is not set +# CONFIG_DEVFREQ_GOV_PERFORMANCE is not set +# CONFIG_DEVFREQ_GOV_POWERSAVE is not set +# CONFIG_DEVFREQ_GOV_SIMPLE_ONDEMAND is not set +# CONFIG_DEVFREQ_GOV_USERSPACE is not set +# CONFIG_DEVFREQ_THERMAL is not set +CONFIG_DMADEVICES=y +CONFIG_DMA_ENGINE=y +CONFIG_DMA_OF=y +CONFIG_DMA_OPS=y +CONFIG_DMA_REMAP=y +CONFIG_DMA_VIRTUAL_CHANNELS=y +CONFIG_DTC=y +CONFIG_DT_IDLE_STATES=y +# CONFIG_DWMAC_GENERIC is not set +CONFIG_DWMAC_IPQ806X=y +# CONFIG_DWMAC_QCOM_ETHQOS is not set +CONFIG_DYNAMIC_DEBUG=y +CONFIG_EDAC_ATOMIC_SCRUB=y +CONFIG_EDAC_SUPPORT=y +CONFIG_ETHERNET_PACKET_MANGLE=y +CONFIG_FIXED_PHY=y +CONFIG_FIX_EARLYCON_MEM=y +CONFIG_FW_LOADER_PAGED_BUF=y +CONFIG_GENERIC_ALLOCATOR=y +CONFIG_GENERIC_BUG=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y +CONFIG_GENERIC_CPU_AUTOPROBE=y +CONFIG_GENERIC_EARLY_IOREMAP=y +CONFIG_GENERIC_GETTIMEOFDAY=y +CONFIG_GENERIC_IDLE_POLL_SETUP=y +CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y +CONFIG_GENERIC_IRQ_MULTI_HANDLER=y +CONFIG_GENERIC_IRQ_SHOW=y +CONFIG_GENERIC_IRQ_SHOW_LEVEL=y +CONFIG_GENERIC_MSI_IRQ=y +CONFIG_GENERIC_MSI_IRQ_DOMAIN=y +CONFIG_GENERIC_PCI_IOMAP=y +CONFIG_GENERIC_PHY=y +CONFIG_GENERIC_PINCONF=y +CONFIG_GENERIC_PINCTRL_GROUPS=y +CONFIG_GENERIC_PINMUX_FUNCTIONS=y +CONFIG_GENERIC_SCHED_CLOCK=y +CONFIG_GENERIC_SMP_IDLE_THREAD=y +CONFIG_GENERIC_STRNCPY_FROM_USER=y +CONFIG_GENERIC_STRNLEN_USER=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_VDSO_32=y +CONFIG_GPIOLIB=y +CONFIG_GPIOLIB_IRQCHIP=y +CONFIG_GRO_CELLS=y +CONFIG_HANDLE_DOMAIN_IRQ=y +CONFIG_HARDEN_BRANCH_PREDICTOR=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT_MAP=y +CONFIG_HAVE_SMP=y +CONFIG_HIGHMEM=y +# CONFIG_HIGHPTE is not set +CONFIG_HWMON=y +CONFIG_HWSPINLOCK=y +CONFIG_HWSPINLOCK_QCOM=y +CONFIG_HW_RANDOM=y +CONFIG_HZ=100 +CONFIG_HZ_100=y +CONFIG_HZ_FIXED=0 +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_CHARDEV=y +CONFIG_I2C_HELPER_AUTO=y +# CONFIG_I2C_QCOM_CCI is not set +CONFIG_I2C_QUP=y +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_IOMMU_DEBUGFS is not set +# CONFIG_IOMMU_IO_PGTABLE_ARMV7S is not set +# CONFIG_IOMMU_IO_PGTABLE_LPAE is not set +CONFIG_IOMMU_SUPPORT=y +# CONFIG_IPQ_APSS_PLL is not set +# CONFIG_IPQ_GCC_4019 is not set +# CONFIG_IPQ_GCC_6018 is not set +CONFIG_IPQ_GCC_806X=y +# CONFIG_IPQ_GCC_8074 is not set +# CONFIG_IPQ_LCC_806X is not set +CONFIG_IRQCHIP=y +CONFIG_IRQ_DOMAIN=y +CONFIG_IRQ_DOMAIN_HIERARCHY=y +CONFIG_IRQ_FASTEOI_HIERARCHY_HANDLERS=y +CONFIG_IRQ_FORCED_THREADING=y +CONFIG_IRQ_WORK=y +CONFIG_KPSS_XCC=y +CONFIG_KRAITCC=y +CONFIG_KRAIT_CLOCKS=y +CONFIG_KRAIT_L2_ACCESSORS=y +CONFIG_LIBFDT=y +CONFIG_LLD_VERSION=0 +CONFIG_LOCK_DEBUGGING_SUPPORT=y +CONFIG_LOCK_SPIN_ON_OWNER=y +CONFIG_LZO_COMPRESS=y +CONFIG_LZO_DECOMPRESS=y +CONFIG_MDIO_BITBANG=y +CONFIG_MDIO_BUS=y +CONFIG_MDIO_DEVICE=y +CONFIG_MDIO_GPIO=y +CONFIG_MDIO_IPQ8064=y +# CONFIG_MDM_GCC_9615 is not set +# CONFIG_MDM_LCC_9615 is not set +CONFIG_MEMFD_CREATE=y +# CONFIG_MFD_HI6421_SPMI is not set +CONFIG_MFD_QCOM_RPM=y +# CONFIG_MFD_SPMI_PMIC is not set +CONFIG_MFD_SYSCON=y +CONFIG_MIGHT_HAVE_CACHE_L2X0=y +CONFIG_MIGRATION=y +CONFIG_MMC=y +CONFIG_MMC_ARMMMCI=y +CONFIG_MMC_BLOCK=y +CONFIG_MMC_BLOCK_MINORS=16 +CONFIG_MMC_CQHCI=y +CONFIG_MMC_QCOM_DML=y +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_IO_ACCESSORS=y +CONFIG_MMC_SDHCI_MSM=y +# CONFIG_MMC_SDHCI_PCI is not set +CONFIG_MMC_SDHCI_PLTFM=y +# CONFIG_MMC_TIFM_SD is not set +CONFIG_MODULES_USE_ELF_REL=y +CONFIG_MSM_GCC_8660=y +# CONFIG_MSM_GCC_8916 is not set +# CONFIG_MSM_GCC_8939 is not set +# CONFIG_MSM_GCC_8960 is not set +# CONFIG_MSM_GCC_8974 is not set +# CONFIG_MSM_GCC_8994 is not set +# CONFIG_MSM_GCC_8996 is not set +# CONFIG_MSM_GCC_8998 is not set +# CONFIG_MSM_GPUCC_8998 is not set +# CONFIG_MSM_IOMMU is not set +# CONFIG_MSM_LCC_8960 is not set +# CONFIG_MSM_MMCC_8960 is not set +# CONFIG_MSM_MMCC_8974 is not set +# CONFIG_MSM_MMCC_8996 is not set +# CONFIG_MSM_MMCC_8998 is not set +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_NAND_CORE=y +CONFIG_MTD_NAND_ECC=y +CONFIG_MTD_NAND_ECC_SW_HAMMING=y +CONFIG_MTD_NAND_QCOM=y +CONFIG_MTD_QCOMSMEM_PARTS=y +CONFIG_MTD_RAW_NAND=y +CONFIG_MTD_SPI_NOR=y +CONFIG_MTD_SPLIT_FIRMWARE=y +CONFIG_MTD_SPLIT_FIT_FW=y +CONFIG_MTD_SPLIT_UIMAGE_FW=y +CONFIG_MTD_UBI=y +CONFIG_MTD_UBI_BEB_LIMIT=20 +CONFIG_MTD_UBI_BLOCK=y +CONFIG_MTD_UBI_WL_THRESHOLD=4096 +CONFIG_MUTEX_SPIN_ON_OWNER=y +CONFIG_NEED_DMA_MAP_STATE=y +CONFIG_NEON=y +CONFIG_NET_DEVLINK=y +CONFIG_NET_DSA=y +CONFIG_NET_DSA_QCA8K=y +CONFIG_NET_DSA_TAG_QCA=y +CONFIG_NET_FLOW_LIMIT=y +CONFIG_NET_PTP_CLASSIFY=y +CONFIG_NET_SWITCHDEV=y +CONFIG_NLS=y +CONFIG_NO_HZ=y +CONFIG_NO_HZ_COMMON=y +CONFIG_NO_HZ_IDLE=y +CONFIG_NR_CPUS=2 +CONFIG_NVMEM=y +# CONFIG_NVMEM_SPMI_SDAM is not set +CONFIG_OF=y +CONFIG_OF_ADDRESS=y +CONFIG_OF_EARLY_FLATTREE=y +CONFIG_OF_FLATTREE=y +CONFIG_OF_GPIO=y +CONFIG_OF_IRQ=y +CONFIG_OF_KOBJ=y +CONFIG_OF_MDIO=y +CONFIG_OF_NET=y +CONFIG_OLD_SIGACTION=y +CONFIG_OLD_SIGSUSPEND3=y +CONFIG_PADATA=y +CONFIG_PAGE_OFFSET=0xC0000000 +CONFIG_PAGE_POOL=y +CONFIG_PCI=y +CONFIG_PCIEAER=y +CONFIG_PCIEPORTBUS=y +CONFIG_PCIE_DW=y +CONFIG_PCIE_DW_HOST=y +CONFIG_PCIE_QCOM=y +CONFIG_PCI_DEBUG=y +CONFIG_PCI_DISABLE_COMMON_QUIRKS=y +CONFIG_PCI_DOMAINS=y +CONFIG_PCI_DOMAINS_GENERIC=y +CONFIG_PCI_MSI=y +CONFIG_PCI_MSI_IRQ_DOMAIN=y +CONFIG_PCS_XPCS=y +CONFIG_PERF_USE_VMALLOC=y +CONFIG_PGTABLE_LEVELS=2 +CONFIG_PHYLIB=y +CONFIG_PHYLINK=y +# CONFIG_PHY_QCOM_APQ8064_SATA is not set +# CONFIG_PHY_QCOM_IPQ4019_USB is not set +CONFIG_PHY_QCOM_IPQ806X_SATA=y +# CONFIG_PHY_QCOM_IPQ806X_USB is not set +# CONFIG_PHY_QCOM_PCIE2 is not set +# CONFIG_PHY_QCOM_QMP is not set +# CONFIG_PHY_QCOM_QUSB2 is not set +# CONFIG_PHY_QCOM_USB_HS_28NM is not set +# CONFIG_PHY_QCOM_USB_SNPS_FEMTO_V2 is not set +# CONFIG_PHY_QCOM_USB_SS is not set +CONFIG_PINCTRL=y +# CONFIG_PINCTRL_APQ8064 is not set +# CONFIG_PINCTRL_APQ8084 is not set +# CONFIG_PINCTRL_IPQ4019 is not set +# CONFIG_PINCTRL_IPQ6018 is not set +CONFIG_PINCTRL_IPQ8064=y +# CONFIG_PINCTRL_IPQ8074 is not set +# CONFIG_PINCTRL_MDM9615 is not set +CONFIG_PINCTRL_MSM=y +# CONFIG_PINCTRL_MSM8226 is not set +# CONFIG_PINCTRL_MSM8660 is not set +# CONFIG_PINCTRL_MSM8916 is not set +# CONFIG_PINCTRL_MSM8960 is not set +# CONFIG_PINCTRL_MSM8976 is not set +# CONFIG_PINCTRL_MSM8994 is not set +# CONFIG_PINCTRL_MSM8996 is not set +# CONFIG_PINCTRL_MSM8998 is not set +# CONFIG_PINCTRL_QCOM_SPMI_PMIC is not set +# CONFIG_PINCTRL_QCOM_SSBI_PMIC is not set +# CONFIG_PINCTRL_QCS404 is not set +# CONFIG_PINCTRL_SC7180 is not set +# CONFIG_PINCTRL_SDM660 is not set +# CONFIG_PINCTRL_SDM845 is not set +# CONFIG_PINCTRL_SM8150 is not set +# CONFIG_PINCTRL_SM8250 is not set +CONFIG_PM_DEVFREQ=y +# CONFIG_PM_DEVFREQ_EVENT is not set +CONFIG_PM_OPP=y +CONFIG_POWER_RESET=y +CONFIG_POWER_RESET_MSM=y +CONFIG_POWER_SUPPLY=y +CONFIG_PPS=y +CONFIG_PRINTK_TIME=y +CONFIG_PTP_1588_CLOCK=y +# CONFIG_QCOM_A53PLL is not set +CONFIG_QCOM_ADM=y +CONFIG_QCOM_BAM_DMA=y +CONFIG_QCOM_CLK_RPM=y +# CONFIG_QCOM_COMMAND_DB is not set +# CONFIG_QCOM_CPR is not set +# CONFIG_QCOM_EBI2 is not set +# CONFIG_QCOM_GENI_SE is not set +CONFIG_QCOM_GSBI=y +CONFIG_QCOM_HFPLL=y +# CONFIG_QCOM_IOMMU is not set +# CONFIG_QCOM_LLCC is not set +# CONFIG_QCOM_OCMEM is not set +# CONFIG_QCOM_PDC is not set +CONFIG_QCOM_QFPROM=y +# CONFIG_QCOM_RMTFS_MEM is not set +CONFIG_QCOM_RPMCC=y +# CONFIG_QCOM_RPMH is not set +CONFIG_QCOM_SCM=y +# CONFIG_QCOM_SCM_DOWNLOAD_MODE_DEFAULT is not set +CONFIG_QCOM_SMEM=y +# CONFIG_QCOM_SMSM is not set +# CONFIG_QCOM_SOCINFO is not set +CONFIG_QCOM_TCSR=y +CONFIG_QCOM_TSENS=y +CONFIG_QCOM_WDT=y +# CONFIG_QCS_GCC_404 is not set +# CONFIG_QCS_Q6SSTOP_404 is not set +# CONFIG_QCS_TURING_404 is not set +CONFIG_RAS=y +CONFIG_RATIONAL=y +CONFIG_REGMAP=y +CONFIG_REGMAP_MMIO=y +CONFIG_REGULATOR=y +CONFIG_REGULATOR_FIXED_VOLTAGE=y +# CONFIG_REGULATOR_QCOM_LABIBB is not set +CONFIG_REGULATOR_QCOM_RPM=y +# CONFIG_REGULATOR_QCOM_SPMI is not set +# CONFIG_REGULATOR_QCOM_USB_VBUS is not set +# CONFIG_REGULATOR_VQMMC_IPQ4019 is not set +CONFIG_RESET_CONTROLLER=y +# CONFIG_RESET_QCOM_AOSS is not set +# CONFIG_RESET_QCOM_PDC is not set +CONFIG_RFS_ACCEL=y +CONFIG_RPS=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_I2C_AND_SPI=y +CONFIG_RTC_MC146818_LIB=y +CONFIG_RWSEM_SPIN_ON_OWNER=y +# CONFIG_SC_DISPCC_7180 is not set +# CONFIG_SC_GCC_7180 is not set +# CONFIG_SC_GPUCC_7180 is not set +# CONFIG_SC_LPASS_CORECC_7180 is not set +# CONFIG_SC_MSS_7180 is not set +# CONFIG_SC_VIDEOCC_7180 is not set +# CONFIG_SDM_CAMCC_845 is not set +# CONFIG_SDM_DISPCC_845 is not set +# CONFIG_SDM_GCC_660 is not set +# CONFIG_SDM_GCC_845 is not set +# CONFIG_SDM_GPUCC_845 is not set +# CONFIG_SDM_LPASSCC_845 is not set +# CONFIG_SDM_VIDEOCC_845 is not set +CONFIG_SERIAL_8250_FSL=y +CONFIG_SERIAL_MCTRL_GPIO=y +CONFIG_SERIAL_MSM=y +CONFIG_SERIAL_MSM_CONSOLE=y +CONFIG_SGL_ALLOC=y +CONFIG_SMP=y +CONFIG_SMP_ON_UP=y +# CONFIG_SM_GCC_8150 is not set +# CONFIG_SM_GCC_8250 is not set +# CONFIG_SM_GPUCC_8150 is not set +# CONFIG_SM_GPUCC_8250 is not set +# CONFIG_SM_VIDEOCC_8150 is not set +# CONFIG_SM_VIDEOCC_8250 is not set +CONFIG_SPARSE_IRQ=y +CONFIG_SPI=y +CONFIG_SPI_MASTER=y +CONFIG_SPI_MEM=y +CONFIG_SPI_QUP=y +CONFIG_SPMI=y +# CONFIG_SPMI_HISI3670 is not set +CONFIG_SPMI_MSM_PMIC_ARB=y +# CONFIG_SPMI_PMIC_CLKDIV is not set +CONFIG_SRCU=y +CONFIG_STMMAC_ETH=y +CONFIG_STMMAC_PLATFORM=y +# CONFIG_STMMAC_SELFTESTS is not set +CONFIG_SWCONFIG=y +CONFIG_SWCONFIG_LEDS=y +CONFIG_SWPHY=y +CONFIG_SWP_EMULATE=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_THERMAL=y +CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y +CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0 +CONFIG_THERMAL_GOV_STEP_WISE=y +CONFIG_THERMAL_HWMON=y +CONFIG_THERMAL_OF=y +CONFIG_TICK_CPU_ACCOUNTING=y +CONFIG_TIMER_OF=y +CONFIG_TIMER_PROBE=y +CONFIG_TREE_RCU=y +CONFIG_TREE_SRCU=y +CONFIG_UBIFS_FS=y +CONFIG_UBIFS_FS_ADVANCED_COMPR=y +CONFIG_UBIFS_FS_LZO=y +CONFIG_UBIFS_FS_ZLIB=y +CONFIG_UBIFS_FS_ZSTD=y +# CONFIG_UCLAMP_TASK is not set +CONFIG_UEVENT_HELPER_PATH="" +CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h" +CONFIG_UNWINDER_ARM=y +CONFIG_USB=y +CONFIG_USB_COMMON=y +CONFIG_USB_SUPPORT=y +CONFIG_USE_OF=y +CONFIG_VFP=y +CONFIG_VFPv3=y +CONFIG_WATCHDOG_CORE=y +CONFIG_XPS=y +CONFIG_XXHASH=y +CONFIG_XZ_DEC_ARM=y +CONFIG_XZ_DEC_BCJ=y +CONFIG_ZBOOT_ROM_BSS=0 +CONFIG_ZBOOT_ROM_TEXT=0 +CONFIG_ZLIB_DEFLATE=y +CONFIG_ZLIB_INFLATE=y +CONFIG_ZSTD_COMPRESS=y +CONFIG_ZSTD_DECOMPRESS=y diff --git a/target/linux/ipq806x/patches-5.15/0001-dtbindings-qcom_adm-Fix-channel-specifiers.patch b/target/linux/ipq806x/patches-5.15/0001-dtbindings-qcom_adm-Fix-channel-specifiers.patch new file mode 100644 index 0000000000..83d7bbc6f4 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/0001-dtbindings-qcom_adm-Fix-channel-specifiers.patch @@ -0,0 +1,71 @@ +From 28d0ed88f536dd639adf1b0c7c08e04be3c8f294 Mon Sep 17 00:00:00 2001 +From: Thomas Pedersen +Date: Mon, 16 May 2016 17:58:50 -0700 +Subject: [PATCH 01/69] dtbindings: qcom_adm: Fix channel specifiers + +Original patch from Andy Gross. + +This patch removes the crci information from the dma +channel property. At least one client device requires +using more than one CRCI value for a channel. This does +not match the current binding and the crci information +needs to be removed. + +Instead, the client device will provide this information +via other means. + +Signed-off-by: Andy Gross +Signed-off-by: Thomas Pedersen +--- + Documentation/devicetree/bindings/dma/qcom_adm.txt | 16 ++++++---------- + 1 file changed, 6 insertions(+), 10 deletions(-) + +--- a/Documentation/devicetree/bindings/dma/qcom_adm.txt ++++ b/Documentation/devicetree/bindings/dma/qcom_adm.txt +@@ -4,8 +4,7 @@ Required properties: + - compatible: must contain "qcom,adm" for IPQ/APQ8064 and MSM8960 + - reg: Address range for DMA registers + - interrupts: Should contain one interrupt shared by all channels +-- #dma-cells: must be <2>. First cell denotes the channel number. Second cell +- denotes CRCI (client rate control interface) flow control assignment. ++- #dma-cells: must be <1>. First cell denotes the channel number. + - clocks: Should contain the core clock and interface clock. + - clock-names: Must contain "core" for the core clock and "iface" for the + interface clock. +@@ -22,7 +21,7 @@ Example: + compatible = "qcom,adm"; + reg = <0x18300000 0x100000>; + interrupts = <0 170 0>; +- #dma-cells = <2>; ++ #dma-cells = <1>; + + clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>; + clock-names = "core", "iface"; +@@ -35,15 +34,12 @@ Example: + qcom,ee = <0>; + }; + +-DMA clients must use the format descripted in the dma.txt file, using a three ++DMA clients must use the format descripted in the dma.txt file, using a two + cell specifier for each channel. + +-Each dmas request consists of 3 cells: ++Each dmas request consists of two cells: + 1. phandle pointing to the DMA controller + 2. channel number +- 3. CRCI assignment, if applicable. If no CRCI flow control is required, use 0. +- The CRCI is used for flow control. It identifies the peripheral device that +- is the source/destination for the transferred data. + + Example: + +@@ -55,7 +51,7 @@ Example: + + cs-gpios = <&qcom_pinmux 20 0>; + +- dmas = <&adm_dma 6 9>, +- <&adm_dma 5 10>; ++ dmas = <&adm_dma 6>, ++ <&adm_dma 5>; + dma-names = "rx", "tx"; + }; diff --git a/target/linux/ipq806x/patches-5.15/0033-ARM-qcom-automatically-select-PCI_DOMAINS-if-PCI-is-.patch b/target/linux/ipq806x/patches-5.15/0033-ARM-qcom-automatically-select-PCI_DOMAINS-if-PCI-is-.patch new file mode 100644 index 0000000000..a12aa721e2 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/0033-ARM-qcom-automatically-select-PCI_DOMAINS-if-PCI-is-.patch @@ -0,0 +1,29 @@ +From 48051ece78136e4235a2415a52797db56f8a4478 Mon Sep 17 00:00:00 2001 +From: Mathieu Olivari +Date: Tue, 21 Apr 2015 19:09:07 -0700 +Subject: [PATCH 33/69] ARM: qcom: automatically select PCI_DOMAINS if PCI is + enabled + +If multiple PCIe devices are present in the system, the kernel will +panic at boot time when trying to scan the PCI buses. This happens on +IPQ806x based platforms, which has 3 PCIe ports. + +Enabling this option allows the kernel to assign the pci-domains +according to the device-tree content. This allows multiple PCIe +controllers to coexist in the system. + +Signed-off-by: Mathieu Olivari +--- + arch/arm/mach-qcom/Kconfig | 1 + + 1 file changed, 1 insertion(+) + +--- a/arch/arm/mach-qcom/Kconfig ++++ b/arch/arm/mach-qcom/Kconfig +@@ -7,6 +7,7 @@ menuconfig ARCH_QCOM + select ARM_AMBA + select PINCTRL + select QCOM_SCM if SMP ++ select PCI_DOMAINS if PCI + help + Support for Qualcomm's devicetree based systems. + diff --git a/target/linux/ipq806x/patches-5.15/0060-HACK-arch-arm-force-ZRELADDR-on-arch-qcom.patch b/target/linux/ipq806x/patches-5.15/0060-HACK-arch-arm-force-ZRELADDR-on-arch-qcom.patch new file mode 100644 index 0000000000..b73218e71b --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/0060-HACK-arch-arm-force-ZRELADDR-on-arch-qcom.patch @@ -0,0 +1,62 @@ +From fa71139b55e114aa8c3c4823ff8ee7d49ee810d4 Mon Sep 17 00:00:00 2001 +From: Mathieu Olivari +Date: Wed, 29 Apr 2015 15:21:46 -0700 +Subject: [PATCH 60/69] HACK: arch: arm: force ZRELADDR on arch-qcom + +ARCH_QCOM is using the ARCH_MULTIPLATFORM option, as now recommended +on most ARM architectures. This automatically calculate ZRELADDR by +masking PHYS_OFFSET with 0xf8000000. + +However, on IPQ806x, the first ~20MB of RAM is reserved for the hardware +network accelerators, and the bootloader removes this section from the +layout passed from the ATAGS (when used). + +For newer bootloader, when DT is used, this is not a problem, we just +reserve this memory in the device tree. But if the bootloader doesn't +have DT support, then ATAGS have to be used. In this case, the ARM +decompressor will position the kernel in this low mem, which will not be +in the RAM section mapped by the bootloader, which means the kernel will +freeze in the middle of the boot process trying to map the memory. + +As a work around, this patch allows disabling AUTO_ZRELADDR when +ARCH_QCOM is selected. It makes the zImage usage possible on bootloaders +which don't support device-tree, which is the case on certain early +IPQ806x based designs. + +Signed-off-by: Mathieu Olivari +--- + arch/arm/Kconfig | 2 +- + arch/arm/Makefile | 2 ++ + arch/arm/mach-qcom/Makefile.boot | 1 + + 3 files changed, 4 insertions(+), 1 deletion(-) + create mode 100644 arch/arm/mach-qcom/Makefile.boot + +--- a/arch/arm/Kconfig ++++ b/arch/arm/Kconfig +@@ -322,7 +322,7 @@ config ARCH_MULTIPLATFORM + select ARCH_SELECT_MEMORY_MODEL + select ARM_HAS_SG_CHAIN + select ARM_PATCH_PHYS_VIRT +- select AUTO_ZRELADDR ++ select AUTO_ZRELADDR if !ARCH_QCOM + select TIMER_OF + select COMMON_CLK + select GENERIC_CLOCKEVENTS +--- a/arch/arm/Makefile ++++ b/arch/arm/Makefile +@@ -251,9 +251,11 @@ MACHINE := arch/arm/mach-$(word 1,$(mac + else + MACHINE := + endif ++ifeq ($(CONFIG_ARCH_QCOM),) + ifeq ($(CONFIG_ARCH_MULTIPLATFORM),y) + MACHINE := + endif ++endif + + machdirs := $(patsubst %,arch/arm/mach-%/,$(machine-y)) + platdirs := $(patsubst %,arch/arm/plat-%/,$(sort $(plat-y))) +--- /dev/null ++++ b/arch/arm/mach-qcom/Makefile.boot +@@ -0,0 +1 @@ ++zreladdr-y+= 0x42208000 diff --git a/target/linux/ipq806x/patches-5.15/0065-arm-override-compiler-flags.patch b/target/linux/ipq806x/patches-5.15/0065-arm-override-compiler-flags.patch new file mode 100644 index 0000000000..a1a0371fbc --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/0065-arm-override-compiler-flags.patch @@ -0,0 +1,21 @@ +From 4d8e29642661397a339ac3485f212c6360445421 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Thu, 9 Mar 2017 09:33:32 +0100 +Subject: [PATCH 65/69] arm: override compiler flags + +Signed-off-by: John Crispin +--- + arch/arm/Makefile | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/arch/arm/Makefile ++++ b/arch/arm/Makefile +@@ -61,7 +61,7 @@ KBUILD_CFLAGS += $(call cc-option,-fno-i + # macro, but instead defines a whole series of macros which makes + # testing for a specific architecture or later rather impossible. + arch-$(CONFIG_CPU_32v7M) =-D__LINUX_ARM_ARCH__=7 -march=armv7-m +-arch-$(CONFIG_CPU_32v7) =-D__LINUX_ARM_ARCH__=7 -march=armv7-a ++arch-$(CONFIG_CPU_32v7) =-D__LINUX_ARM_ARCH__=7 -mcpu=cortex-a15 + arch-$(CONFIG_CPU_32v6) =-D__LINUX_ARM_ARCH__=6 -march=armv6 + # Only override the compiler option if ARMv6. The ARMv6K extensions are + # always available in ARMv7 diff --git a/target/linux/ipq806x/patches-5.15/0067-generic-Mangle-bootloader-s-kernel-arguments.patch b/target/linux/ipq806x/patches-5.15/0067-generic-Mangle-bootloader-s-kernel-arguments.patch new file mode 100644 index 0000000000..8f669319ed --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/0067-generic-Mangle-bootloader-s-kernel-arguments.patch @@ -0,0 +1,210 @@ +From 71270226b14733a4b1f2cde58ea9265caa50b38d Mon Sep 17 00:00:00 2001 +From: Adrian Panella +Date: Thu, 9 Mar 2017 09:37:17 +0100 +Subject: [PATCH 67/69] generic: Mangle bootloader's kernel arguments + +The command-line arguments provided by the boot loader will be +appended to a new device tree property: bootloader-args. +If there is a property "append-rootblock" in DT under /chosen +and a root= option in bootloaders command line it will be parsed +and added to DT bootargs with the form: XX. +Only command line ATAG will be processed, the rest of the ATAGs +sent by bootloader will be ignored. +This is usefull in dual boot systems, to get the current root partition +without afecting the rest of the system. + +Signed-off-by: Adrian Panella +--- + arch/arm/Kconfig | 11 +++++ + arch/arm/boot/compressed/atags_to_fdt.c | 72 ++++++++++++++++++++++++++++++++- + init/main.c | 16 ++++++++ + 3 files changed, 98 insertions(+), 1 deletion(-) + +--- a/arch/arm/Kconfig ++++ b/arch/arm/Kconfig +@@ -1781,6 +1781,17 @@ config ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEN + The command-line arguments provided by the boot loader will be + appended to the the device tree bootargs property. + ++config ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE ++ bool "Append rootblock parsing bootloader's kernel arguments" ++ help ++ The command-line arguments provided by the boot loader will be ++ appended to a new device tree property: bootloader-args. ++ If there is a property "append-rootblock" in DT under /chosen ++ and a root= option in bootloaders command line it will be parsed ++ and added to DT bootargs with the form: XX. ++ Only command line ATAG will be processed, the rest of the ATAGs ++ sent by bootloader will be ignored. ++ + endchoice + + config CMDLINE +--- a/arch/arm/boot/compressed/atags_to_fdt.c ++++ b/arch/arm/boot/compressed/atags_to_fdt.c +@@ -5,6 +5,8 @@ + + #if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND) + #define do_extend_cmdline 1 ++#elif defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE) ++#define do_extend_cmdline 1 + #else + #define do_extend_cmdline 0 + #endif +@@ -69,6 +71,80 @@ static uint32_t get_cell_size(const void + return cell_size; + } + ++#if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE) ++/** ++ * taken from arch/x86/boot/string.c ++ * local_strstr - Find the first substring in a %NUL terminated string ++ * @s1: The string to be searched ++ * @s2: The string to search for ++ */ ++static char *local_strstr(const char *s1, const char *s2) ++{ ++ size_t l1, l2; ++ ++ l2 = strlen(s2); ++ if (!l2) ++ return (char *)s1; ++ l1 = strlen(s1); ++ while (l1 >= l2) { ++ l1--; ++ if (!memcmp(s1, s2, l2)) ++ return (char *)s1; ++ s1++; ++ } ++ return NULL; ++} ++ ++static char *append_rootblock(char *dest, const char *str, int len, void *fdt) ++{ ++ char *ptr, *end, *tmp; ++ char *root="root="; ++ char *find_rootblock; ++ int i, l; ++ const char *rootblock; ++ ++ find_rootblock = getprop(fdt, "/chosen", "find-rootblock", &l); ++ if(!find_rootblock) ++ find_rootblock = root; ++ ++ //ARM doesn't have __HAVE_ARCH_STRSTR, so it was copied from x86 ++ ptr = local_strstr(str, find_rootblock); ++ ++ if(!ptr) ++ return dest; ++ ++ end = strchr(ptr, ' '); ++ end = end ? (end - 1) : (strchr(ptr, 0) - 1); ++ ++ // Some boards ubi.mtd=XX,ZZZZ, so let's check for '," too. ++ tmp = strchr(ptr, ','); ++ ++ if(tmp) ++ end = end < tmp ? end : tmp - 1; ++ ++ //find partition number (assumes format root=/dev/mtdXX | /dev/mtdblockXX | yy:XX | ubi.mtd=XX,ZZZZ ) ++ for( i = 0; end >= ptr && *end >= '0' && *end <= '9'; end--, i++); ++ ptr = end + 1; ++ ++ /* if append-rootblock property is set use it to append to command line */ ++ rootblock = getprop(fdt, "/chosen", "append-rootblock", &l); ++ if(rootblock != NULL) { ++ if(*dest != ' ') { ++ *dest = ' '; ++ dest++; ++ len++; ++ } ++ if (len + l + i <= COMMAND_LINE_SIZE) { ++ memcpy(dest, rootblock, l); ++ dest += l - 1; ++ memcpy(dest, ptr, i); ++ dest += i; ++ } ++ } ++ return dest; ++} ++#endif ++ + static void merge_fdt_bootargs(void *fdt, const char *fdt_cmdline) + { + char cmdline[COMMAND_LINE_SIZE]; +@@ -88,12 +164,21 @@ static void merge_fdt_bootargs(void *fdt + + /* and append the ATAG_CMDLINE */ + if (fdt_cmdline) { ++ ++#if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE) ++ //save original bootloader args ++ //and append ubi.mtd with root partition number to current cmdline ++ setprop_string(fdt, "/chosen", "bootloader-args", fdt_cmdline); ++ ptr = append_rootblock(ptr, fdt_cmdline, len, fdt); ++ ++#else + len = strlen(fdt_cmdline); + if (ptr - cmdline + len + 2 < COMMAND_LINE_SIZE) { + *ptr++ = ' '; + memcpy(ptr, fdt_cmdline, len); + ptr += len; + } ++#endif + } + *ptr = '\0'; + +@@ -168,7 +253,9 @@ int atags_to_fdt(void *atag_list, void * + else + setprop_string(fdt, "/chosen", "bootargs", + atag->u.cmdline.cmdline); +- } else if (atag->hdr.tag == ATAG_MEM) { ++ } ++#ifndef CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE ++ else if (atag->hdr.tag == ATAG_MEM) { + if (memcount >= sizeof(mem_reg_property)/4) + continue; + if (!atag->u.mem.size) +@@ -212,6 +299,10 @@ int atags_to_fdt(void *atag_list, void * + setprop(fdt, "/memory", "reg", mem_reg_property, + 4 * memcount * memsize); + } ++#else ++ ++ } ++#endif + + return fdt_pack(fdt); + } +--- a/init/main.c ++++ b/init/main.c +@@ -110,6 +110,10 @@ + + #include + ++#if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE) ++#include ++#endif ++ + static int kernel_init(void *); + + extern void init_IRQ(void); +@@ -906,6 +910,18 @@ asmlinkage __visible void __init __no_sa + pr_notice("Kernel command line: %s\n", saved_command_line); + /* parameters may set static keys */ + jump_label_init(); ++ ++#if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE) ++ //Show bootloader's original command line for reference ++ if(of_chosen) { ++ const char *prop = of_get_property(of_chosen, "bootloader-args", NULL); ++ if(prop) ++ pr_notice("Bootloader command line (ignored): %s\n", prop); ++ else ++ pr_notice("Bootloader command line not present\n"); ++ } ++#endif ++ + parse_early_param(); + after_dashes = parse_args("Booting kernel", + static_command_line, __start___param, diff --git a/target/linux/ipq806x/patches-5.15/0069-arm-boot-add-dts-files.patch b/target/linux/ipq806x/patches-5.15/0069-arm-boot-add-dts-files.patch new file mode 100644 index 0000000000..49ff218040 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/0069-arm-boot-add-dts-files.patch @@ -0,0 +1,42 @@ +From 8f68331e14dff9a101f2d0e1d6bec84a031f27ee Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Thu, 9 Mar 2017 11:03:18 +0100 +Subject: [PATCH 69/69] arm: boot: add dts files + +Signed-off-by: John Crispin +--- + arch/arm/boot/dts/Makefile | 8 ++++++++ + 1 file changed, 8 insertions(+) + +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -907,8 +907,29 @@ dtb-$(CONFIG_ARCH_QCOM) += \ + qcom-ipq4019-ap.dk04.1-c3.dtb \ + qcom-ipq4019-ap.dk07.1-c1.dtb \ + qcom-ipq4019-ap.dk07.1-c2.dtb \ ++ qcom-ipq8062-wg2600hp3.dtb \ + qcom-ipq8064-ap148.dtb \ + qcom-ipq8064-rb3011.dtb \ ++ qcom-ipq8064-c2600.dtb \ ++ qcom-ipq8064-d7800.dtb \ ++ qcom-ipq8064-db149.dtb \ ++ qcom-ipq8064-ap161.dtb \ ++ qcom-ipq8064-ea7500-v1.dtb \ ++ qcom-ipq8064-ea8500.dtb \ ++ qcom-ipq8064-g10.dtb \ ++ qcom-ipq8064-r7500.dtb \ ++ qcom-ipq8064-r7500v2.dtb \ ++ qcom-ipq8064-unifi-ac-hd.dtb \ ++ qcom-ipq8064-wg2600hp.dtb \ ++ qcom-ipq8064-wpq864.dtb \ ++ qcom-ipq8064-wxr-2533dhp.dtb \ ++ qcom-ipq8065-nbg6817.dtb \ ++ qcom-ipq8065-r7800.dtb \ ++ qcom-ipq8065-rt4230w-rev6.dtb \ ++ qcom-ipq8065-xr500.dtb \ ++ qcom-ipq8068-ecw5410.dtb \ ++ qcom-ipq8068-mr42.dtb \ ++ qcom-ipq8068-mr52.dtb \ + qcom-msm8660-surf.dtb \ + qcom-msm8960-cdp.dtb \ + qcom-msm8974-fairphone-fp2.dtb \ diff --git a/target/linux/ipq806x/patches-5.15/0072-add-ipq806x-with-no-clocks.patch b/target/linux/ipq806x/patches-5.15/0072-add-ipq806x-with-no-clocks.patch new file mode 100644 index 0000000000..62bba1d72a --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/0072-add-ipq806x-with-no-clocks.patch @@ -0,0 +1,10 @@ +--- a/drivers/firmware/qcom_scm.c ++++ b/drivers/firmware/qcom_scm.c +@@ -1275,6 +1275,7 @@ static const struct of_device_id qcom_sc + SCM_HAS_BUS_CLK) + }, + { .compatible = "qcom,scm-ipq4019" }, ++ { .compatible = "qcom,scm-ipq806x" }, + { .compatible = "qcom,scm-msm8660", .data = (void *) SCM_HAS_CORE_CLK }, + { .compatible = "qcom,scm-msm8960", .data = (void *) SCM_HAS_CORE_CLK }, + { .compatible = "qcom,scm-msm8916", .data = (void *)(SCM_HAS_CORE_CLK | diff --git a/target/linux/ipq806x/patches-5.15/082-ipq8064-dtsi-tweaks.patch b/target/linux/ipq806x/patches-5.15/082-ipq8064-dtsi-tweaks.patch new file mode 100644 index 0000000000..d6a4593749 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/082-ipq8064-dtsi-tweaks.patch @@ -0,0 +1,220 @@ +--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi +@@ -20,7 +20,7 @@ + #address-cells = <1>; + #size-cells = <0>; + +- cpu@0 { ++ cpu0: cpu@0 { + compatible = "qcom,krait"; + enable-method = "qcom,kpss-acc-v1"; + device_type = "cpu"; +@@ -30,7 +30,7 @@ + qcom,saw = <&saw0>; + }; + +- cpu@1 { ++ cpu1: cpu@1 { + compatible = "qcom,krait"; + enable-method = "qcom,kpss-acc-v1"; + device_type = "cpu"; +@@ -67,7 +67,7 @@ + no-map; + }; + +- smem@41000000 { ++ smem: smem@41000000 { + reg = <0x41000000 0x200000>; + no-map; + }; +@@ -128,6 +128,7 @@ + gpio-ranges = <&qcom_pinmux 0 0 69>; + #gpio-cells = <2>; + interrupt-controller; ++ #address-cells = <0>; + #interrupt-cells = <2>; + interrupts = ; + +@@ -155,6 +156,7 @@ + function = "pcie3_rst"; + drive-strength = <12>; + bias-disable; ++ output-low; + }; + }; + +@@ -190,6 +192,7 @@ + intc: interrupt-controller@2000000 { + compatible = "qcom,msm-qgic2"; + interrupt-controller; ++ #address-cells = <0>; + #interrupt-cells = <3>; + reg = <0x02000000 0x1000>, + <0x02002000 0x1000>; +@@ -219,21 +222,23 @@ + acc0: clock-controller@2088000 { + compatible = "qcom,kpss-acc-v1"; + reg = <0x02088000 0x1000>, <0x02008000 0x1000>; ++ clock-output-names = "acpu0_aux"; + }; + + acc1: clock-controller@2098000 { + compatible = "qcom,kpss-acc-v1"; + reg = <0x02098000 0x1000>, <0x02008000 0x1000>; ++ clock-output-names = "acpu1_aux"; + }; + + saw0: regulator@2089000 { +- compatible = "qcom,saw2"; ++ compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon"; + reg = <0x02089000 0x1000>, <0x02009000 0x1000>; + regulator; + }; + + saw1: regulator@2099000 { +- compatible = "qcom,saw2"; ++ compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon"; + reg = <0x02099000 0x1000>, <0x02009000 0x1000>; + regulator; + }; +@@ -251,7 +256,7 @@ + + syscon-tcsr = <&tcsr>; + +- serial@12490000 { ++ gsbi2_serial: serial@12490000 { + compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; + reg = <0x12490000 0x1000>, + <0x12480000 0x1000>; +@@ -261,7 +266,7 @@ + status = "disabled"; + }; + +- i2c@124a0000 { ++ gsbi2_i2c: i2c@124a0000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x124a0000 0x1000>; + interrupts = ; +@@ -326,7 +331,7 @@ + + syscon-tcsr = <&tcsr>; + +- serial@1a240000 { ++ gsbi5_serial: serial@1a240000 { + compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; + reg = <0x1a240000 0x1000>, + <0x1a200000 0x1000>; +@@ -397,7 +402,7 @@ + status = "disabled"; + }; + +- sata@29000000 { ++ sata: sata@29000000 { + compatible = "qcom,ipq806x-ahci", "generic-ahci"; + reg = <0x29000000 0x180>; + +@@ -430,13 +435,35 @@ + reg = <0x00700000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; ++ ++ tsens_calib: calib@400 { ++ reg = <0x400 0xb>; ++ }; ++ tsens_backup: backup@410 { ++ reg = <0x410 0xb>; ++ }; ++ speedbin_efuse: speedbin@0c0 { ++ reg = <0x0c0 0x4>; ++ }; + }; + + gcc: clock-controller@900000 { +- compatible = "qcom,gcc-ipq8064"; ++ compatible = "qcom,gcc-ipq8064", "syscon"; + reg = <0x00900000 0x4000>; + #clock-cells = <1>; + #reset-cells = <1>; ++ #power-domain-cells = <1>; ++ ++ tsens: thermal-sensor@900000 { ++ compatible = "qcom,ipq8064-tsens"; ++ ++ nvmem-cells = <&tsens_calib>, <&tsens_backup>; ++ nvmem-cell-names = "calib", "calib_backup"; ++ interrupts = ; ++ interrupt-names = "uplow"; ++ #thermal-sensor-cells = <1>; ++ #qcom,sensors = <11>; ++ }; + }; + + tcsr: syscon@1a400000 { +@@ -622,7 +649,7 @@ + + gmac0: ethernet@37000000 { + device_type = "network"; +- compatible = "qcom,ipq806x-gmac"; ++ compatible = "qcom,ipq806x-gmac", "snps,dwmac"; + reg = <0x37000000 0x200000>; + interrupts = ; + interrupt-names = "macirq"; +@@ -645,7 +672,7 @@ + + gmac1: ethernet@37200000 { + device_type = "network"; +- compatible = "qcom,ipq806x-gmac"; ++ compatible = "qcom,ipq806x-gmac", "snps,dwmac"; + reg = <0x37200000 0x200000>; + interrupts = ; + interrupt-names = "macirq"; +@@ -668,7 +695,7 @@ + + gmac2: ethernet@37400000 { + device_type = "network"; +- compatible = "qcom,ipq806x-gmac"; ++ compatible = "qcom,ipq806x-gmac", "snps,dwmac"; + reg = <0x37400000 0x200000>; + interrupts = ; + interrupt-names = "macirq"; +@@ -691,7 +718,7 @@ + + gmac3: ethernet@37600000 { + device_type = "network"; +- compatible = "qcom,ipq806x-gmac"; ++ compatible = "qcom,ipq806x-gmac", "snps,dwmac"; + reg = <0x37600000 0x200000>; + interrupts = ; + interrupt-names = "macirq"; +@@ -740,13 +767,13 @@ + qcom,ee = <0>; + }; + +- amba { +- compatible = "simple-bus"; ++ amba: amba { ++ compatible = "arm,amba-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + +- sdcc@12400000 { ++ sdcc1: sdcc@12400000 { + status = "disabled"; + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00051180>; +@@ -760,13 +787,12 @@ + non-removable; + cap-sd-highspeed; + cap-mmc-highspeed; +- mmc-ddr-1_8v; + vmmc-supply = <&vsdcc_fixed>; + dmas = <&sdcc1bam 2>, <&sdcc1bam 1>; + dma-names = "tx", "rx"; + }; + +- sdcc@12180000 { ++ sdcc3: sdcc@12180000 { + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00051180>; + status = "disabled"; diff --git a/target/linux/ipq806x/patches-5.15/083-ipq8064-dtsi-additions.patch b/target/linux/ipq806x/patches-5.15/083-ipq8064-dtsi-additions.patch new file mode 100644 index 0000000000..2667bd636e --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/083-ipq8064-dtsi-additions.patch @@ -0,0 +1,846 @@ +--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi +@@ -8,6 +8,8 @@ + #include + #include + #include ++#include ++#include + + / { + #address-cells = <1>; +@@ -28,6 +30,16 @@ + next-level-cache = <&L2>; + qcom,acc = <&acc0>; + qcom,saw = <&saw0>; ++ clocks = <&kraitcc 0>, <&kraitcc 4>; ++ clock-names = "cpu", "l2"; ++ clock-latency = <100000>; ++ cpu-supply = <&smb208_s2a>; ++ operating-points-v2 = <&opp_table0>; ++ voltage-tolerance = <5>; ++ cooling-min-state = <0>; ++ cooling-max-state = <10>; ++ #cooling-cells = <2>; ++ cpu-idle-states = <&CPU_SPC>; + }; + + cpu1: cpu@1 { +@@ -38,14 +50,350 @@ + next-level-cache = <&L2>; + qcom,acc = <&acc1>; + qcom,saw = <&saw1>; ++ clocks = <&kraitcc 1>, <&kraitcc 4>; ++ clock-names = "cpu", "l2"; ++ clock-latency = <100000>; ++ cpu-supply = <&smb208_s2b>; ++ operating-points-v2 = <&opp_table0>; ++ voltage-tolerance = <5>; ++ cooling-min-state = <0>; ++ cooling-max-state = <10>; ++ #cooling-cells = <2>; ++ cpu-idle-states = <&CPU_SPC>; ++ }; ++ ++ idle-states { ++ CPU_SPC: spc { ++ compatible = "qcom,idle-state-spc"; ++ status = "disabled"; ++ entry-latency-us = <400>; ++ exit-latency-us = <900>; ++ min-residency-us = <3000>; ++ }; + }; ++ }; + +- L2: l2-cache { +- compatible = "cache"; +- cache-level = <2>; ++ opp_table_l2: opp_table_l2 { ++ compatible = "operating-points-v2"; ++ ++ opp-384000000 { ++ opp-hz = /bits/ 64 <384000000>; ++ opp-microvolt = <1100000>; ++ clock-latency-ns = <100000>; ++ opp-level = <0>; ++ }; ++ ++ opp-1000000000 { ++ opp-hz = /bits/ 64 <1000000000>; ++ opp-microvolt = <1100000>; ++ clock-latency-ns = <100000>; ++ opp-level = <1>; ++ }; ++ ++ opp-1200000000 { ++ opp-hz = /bits/ 64 <1200000000>; ++ opp-microvolt = <1150000>; ++ clock-latency-ns = <100000>; ++ opp-level = <2>; ++ }; ++ }; ++ ++ opp_table0: opp_table0 { ++ compatible = "operating-points-v2-kryo-cpu"; ++ nvmem-cells = <&speedbin_efuse>; ++ ++ /* ++ * Voltage thresholds are ++ */ ++ opp-384000000 { ++ opp-hz = /bits/ 64 <384000000>; ++ opp-microvolt-speed0-pvs0-v0 = <1000000 950000 1050000>; ++ opp-microvolt-speed0-pvs1-v0 = <925000 878750 971250>; ++ opp-microvolt-speed0-pvs2-v0 = <875000 831250 918750>; ++ opp-microvolt-speed0-pvs3-v0 = <800000 760000 840000>; ++ opp-supported-hw = <0x1>; ++ clock-latency-ns = <100000>; ++ opp-level = <0>; ++ }; ++ ++ opp-600000000 { ++ opp-hz = /bits/ 64 <600000000>; ++ opp-microvolt-speed0-pvs0-v0 = <1050000 997500 1102500>; ++ opp-microvolt-speed0-pvs1-v0 = <975000 926250 1023750>; ++ opp-microvolt-speed0-pvs2-v0 = <925000 878750 971250>; ++ opp-microvolt-speed0-pvs3-v0 = <850000 807500 892500>; ++ opp-supported-hw = <0x1>; ++ clock-latency-ns = <100000>; ++ opp-level = <1>; ++ }; ++ ++ opp-800000000 { ++ opp-hz = /bits/ 64 <800000000>; ++ opp-microvolt-speed0-pvs0-v0 = <1100000 1045000 1155000>; ++ opp-microvolt-speed0-pvs1-v0 = <1025000 973750 1076250>; ++ opp-microvolt-speed0-pvs2-v0 = <995000 945250 1044750>; ++ opp-microvolt-speed0-pvs3-v0 = <900000 855000 945000>; ++ opp-supported-hw = <0x1>; ++ clock-latency-ns = <100000>; ++ opp-level = <1>; ++ }; ++ ++ opp-1000000000 { ++ opp-hz = /bits/ 64 <1000000000>; ++ opp-microvolt-speed0-pvs0-v0 = <1150000 1092500 1207500>; ++ opp-microvolt-speed0-pvs1-v0 = <1075000 1021250 1128750>; ++ opp-microvolt-speed0-pvs2-v0 = <1025000 973750 1076250>; ++ opp-microvolt-speed0-pvs3-v0 = <950000 902500 997500>; ++ opp-supported-hw = <0x1>; ++ clock-latency-ns = <100000>; ++ opp-level = <1>; ++ }; ++ ++ opp-1200000000 { ++ opp-hz = /bits/ 64 <1200000000>; ++ opp-microvolt-speed0-pvs0-v0 = <1200000 1140000 1260000>; ++ opp-microvolt-speed0-pvs1-v0 = <1125000 1068750 1181250>; ++ opp-microvolt-speed0-pvs2-v0 = <1075000 1021250 1128750>; ++ opp-microvolt-speed0-pvs3-v0 = <1000000 950000 1050000>; ++ opp-supported-hw = <0x1>; ++ clock-latency-ns = <100000>; ++ opp-level = <2>; ++ }; ++ ++ opp-1400000000 { ++ opp-hz = /bits/ 64 <1400000000>; ++ opp-microvolt-speed0-pvs0-v0 = <1250000 1187500 1312500>; ++ opp-microvolt-speed0-pvs1-v0 = <1175000 1116250 1233750>; ++ opp-microvolt-speed0-pvs2-v0 = <1125000 1068750 1181250>; ++ opp-microvolt-speed0-pvs3-v0 = <1050000 997500 1102500>; ++ opp-supported-hw = <0x1>; ++ clock-latency-ns = <100000>; ++ opp-level = <2>; + }; + }; + ++ thermal-zones { ++ tsens_tz_sensor0 { ++ polling-delay-passive = <0>; ++ polling-delay = <0>; ++ thermal-sensors = <&tsens 0>; ++ ++ trips { ++ cpu-critical { ++ temperature = <105000>; ++ hysteresis = <2000>; ++ type = "critical"; ++ }; ++ ++ cpu-hot { ++ temperature = <95000>; ++ hysteresis = <2000>; ++ type = "hot"; ++ }; ++ }; ++ }; ++ ++ tsens_tz_sensor1 { ++ polling-delay-passive = <0>; ++ polling-delay = <0>; ++ thermal-sensors = <&tsens 1>; ++ ++ trips { ++ cpu-critical { ++ temperature = <105000>; ++ hysteresis = <2000>; ++ type = "critical"; ++ }; ++ ++ cpu-hot { ++ temperature = <95000>; ++ hysteresis = <2000>; ++ type = "hot"; ++ }; ++ }; ++ }; ++ ++ tsens_tz_sensor2 { ++ polling-delay-passive = <0>; ++ polling-delay = <0>; ++ thermal-sensors = <&tsens 2>; ++ ++ trips { ++ cpu-critical { ++ temperature = <105000>; ++ hysteresis = <2000>; ++ type = "critical"; ++ }; ++ ++ cpu-hot { ++ temperature = <95000>; ++ hysteresis = <2000>; ++ type = "hot"; ++ }; ++ }; ++ }; ++ ++ tsens_tz_sensor3 { ++ polling-delay-passive = <0>; ++ polling-delay = <0>; ++ thermal-sensors = <&tsens 3>; ++ ++ trips { ++ cpu-critical { ++ temperature = <105000>; ++ hysteresis = <2000>; ++ type = "critical"; ++ }; ++ ++ cpu-hot { ++ temperature = <95000>; ++ hysteresis = <2000>; ++ type = "hot"; ++ }; ++ }; ++ }; ++ ++ tsens_tz_sensor4 { ++ polling-delay-passive = <0>; ++ polling-delay = <0>; ++ thermal-sensors = <&tsens 4>; ++ ++ trips { ++ cpu-critical { ++ temperature = <105000>; ++ hysteresis = <2000>; ++ type = "critical"; ++ }; ++ ++ cpu-hot { ++ temperature = <95000>; ++ hysteresis = <2000>; ++ type = "hot"; ++ }; ++ }; ++ }; ++ ++ tsens_tz_sensor5 { ++ polling-delay-passive = <0>; ++ polling-delay = <0>; ++ thermal-sensors = <&tsens 5>; ++ ++ trips { ++ cpu-critical { ++ temperature = <105000>; ++ hysteresis = <2000>; ++ type = "critical"; ++ }; ++ ++ cpu-hot { ++ temperature = <95000>; ++ hysteresis = <2000>; ++ type = "hot"; ++ }; ++ }; ++ }; ++ ++ tsens_tz_sensor6 { ++ polling-delay-passive = <0>; ++ polling-delay = <0>; ++ thermal-sensors = <&tsens 6>; ++ ++ trips { ++ cpu-critical { ++ temperature = <105000>; ++ hysteresis = <2000>; ++ type = "critical"; ++ }; ++ ++ cpu-hot { ++ temperature = <95000>; ++ hysteresis = <2000>; ++ type = "hot"; ++ }; ++ }; ++ }; ++ ++ tsens_tz_sensor7 { ++ polling-delay-passive = <0>; ++ polling-delay = <0>; ++ thermal-sensors = <&tsens 7>; ++ ++ trips { ++ cpu-critical { ++ temperature = <105000>; ++ hysteresis = <2000>; ++ type = "critical"; ++ }; ++ ++ cpu-hot { ++ temperature = <95000>; ++ hysteresis = <2000>; ++ type = "hot"; ++ }; ++ }; ++ }; ++ ++ tsens_tz_sensor8 { ++ polling-delay-passive = <0>; ++ polling-delay = <0>; ++ thermal-sensors = <&tsens 8>; ++ ++ trips { ++ cpu-critical { ++ temperature = <105000>; ++ hysteresis = <2000>; ++ type = "critical"; ++ }; ++ ++ cpu-hot { ++ temperature = <95000>; ++ hysteresis = <2000>; ++ type = "hot"; ++ }; ++ }; ++ }; ++ ++ tsens_tz_sensor9 { ++ polling-delay-passive = <0>; ++ polling-delay = <0>; ++ thermal-sensors = <&tsens 9>; ++ ++ trips { ++ cpu-critical { ++ temperature = <105000>; ++ hysteresis = <2000>; ++ type = "critical"; ++ }; ++ ++ cpu-hot { ++ temperature = <95000>; ++ hysteresis = <2000>; ++ type = "hot"; ++ }; ++ }; ++ }; ++ ++ tsens_tz_sensor10 { ++ polling-delay-passive = <0>; ++ polling-delay = <0>; ++ thermal-sensors = <&tsens 10>; ++ ++ trips { ++ cpu-critical { ++ temperature = <105000>; ++ hysteresis = <2000>; ++ type = "critical"; ++ }; ++ ++ cpu-hot { ++ temperature = <95000>; ++ hysteresis = <2000>; ++ type = "hot"; ++ }; ++ }; ++ }; ++ }; ++ + memory { + device_type = "memory"; + reg = <0x0 0x0>; +@@ -93,6 +441,15 @@ + }; + }; + ++ fab-scaling { ++ compatible = "qcom,fab-scaling"; ++ clocks = <&rpmcc RPM_APPS_FABRIC_A_CLK>, <&rpmcc RPM_EBI1_A_CLK>; ++ clock-names = "apps-fab-clk", "ddr-fab-clk"; ++ fab_freq_high = <533000000>; ++ fab_freq_nominal = <400000000>; ++ cpu_freq_threshold = <1000000000>; ++ }; ++ + firmware { + scm { + compatible = "qcom,scm-ipq806x", "qcom,scm"; +@@ -120,6 +477,78 @@ + reg-names = "lpass-lpaif"; + }; + ++ L2: l2-cache { ++ compatible = "qcom,krait-cache", "cache"; ++ cache-level = <2>; ++ qcom,saw = <&saw_l2>; ++ ++ clocks = <&kraitcc 4>; ++ clock-names = "l2"; ++ l2-supply = <&smb208_s1a>; ++ operating-points-v2 = <&opp_table_l2>; ++ }; ++ ++ rpm: rpm@108000 { ++ compatible = "qcom,rpm-ipq8064"; ++ reg = <0x108000 0x1000>; ++ qcom,ipc = <&l2cc 0x8 2>; ++ ++ interrupts = , ++ , ++ ; ++ interrupt-names = "ack", "err", "wakeup"; ++ ++ clocks = <&gcc RPM_MSG_RAM_H_CLK>; ++ clock-names = "ram"; ++ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ rpmcc: clock-controller { ++ compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc"; ++ #clock-cells = <1>; ++ }; ++ ++ regulators { ++ compatible = "qcom,rpm-smb208-regulators"; ++ ++ smb208_s1a: s1a { ++ regulator-min-microvolt = <1050000>; ++ regulator-max-microvolt = <1150000>; ++ ++ qcom,switch-mode-frequency = <1200000>; ++ }; ++ ++ smb208_s1b: s1b { ++ regulator-min-microvolt = <1050000>; ++ regulator-max-microvolt = <1150000>; ++ ++ qcom,switch-mode-frequency = <1200000>; ++ }; ++ ++ smb208_s2a: s2a { ++ regulator-min-microvolt = < 800000>; ++ regulator-max-microvolt = <1250000>; ++ ++ qcom,switch-mode-frequency = <1200000>; ++ }; ++ ++ smb208_s2b: s2b { ++ regulator-min-microvolt = < 800000>; ++ regulator-max-microvolt = <1250000>; ++ ++ qcom,switch-mode-frequency = <1200000>; ++ }; ++ }; ++ }; ++ ++ rng@1a500000 { ++ compatible = "qcom,prng"; ++ reg = <0x1a500000 0x200>; ++ clocks = <&gcc PRNG_CLK>; ++ clock-names = "core"; ++ }; ++ + qcom_pinmux: pinmux@800000 { + compatible = "qcom,ipq8064-pinctrl"; + reg = <0x800000 0x4000>; +@@ -160,6 +589,15 @@ + }; + }; + ++ i2c4_pins: i2c4_pinmux { ++ mux { ++ pins = "gpio12", "gpio13"; ++ function = "gsbi4"; ++ drive-strength = <12>; ++ bias-disable; ++ }; ++ }; ++ + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19", "gpio21"; +@@ -169,6 +607,53 @@ + }; + }; + ++ nand_pins: nand_pins { ++ disable { ++ pins = "gpio34", "gpio35", "gpio36", ++ "gpio37", "gpio38"; ++ function = "nand"; ++ drive-strength = <10>; ++ bias-disable; ++ }; ++ ++ pullups { ++ pins = "gpio39"; ++ function = "nand"; ++ drive-strength = <10>; ++ bias-pull-up; ++ }; ++ ++ hold { ++ pins = "gpio40", "gpio41", "gpio42", ++ "gpio43", "gpio44", "gpio45", ++ "gpio46", "gpio47"; ++ function = "nand"; ++ drive-strength = <10>; ++ bias-bus-hold; ++ }; ++ }; ++ ++ mdio0_pins: mdio0_pins { ++ mux { ++ pins = "gpio0", "gpio1"; ++ function = "mdio"; ++ drive-strength = <8>; ++ bias-disable; ++ }; ++ }; ++ ++ rgmii2_pins: rgmii2_pins { ++ mux { ++ pins = "gpio27", "gpio28", "gpio29", ++ "gpio30", "gpio31", "gpio32", ++ "gpio51", "gpio52", "gpio59", ++ "gpio60", "gpio61", "gpio62"; ++ function = "rgmii2"; ++ drive-strength = <8>; ++ bias-disable; ++ }; ++ }; ++ + leds_pins: leds_pins { + mux { + pins = "gpio7", "gpio8", "gpio9", +@@ -231,6 +716,17 @@ + clock-output-names = "acpu1_aux"; + }; + ++ l2cc: clock-controller@2011000 { ++ compatible = "qcom,kpss-gcc", "syscon"; ++ reg = <0x2011000 0x1000>; ++ clock-output-names = "acpu_l2_aux"; ++ }; ++ ++ kraitcc: clock-controller { ++ compatible = "qcom,krait-cc-v1"; ++ #clock-cells = <1>; ++ }; ++ + saw0: regulator@2089000 { + compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon"; + reg = <0x02089000 0x1000>, <0x02009000 0x1000>; +@@ -243,6 +739,52 @@ + regulator; + }; + ++ saw_l2: regulator@02012000 { ++ compatible = "qcom,saw2", "syscon"; ++ reg = <0x02012000 0x1000>; ++ regulator; ++ }; ++ ++ sic_non_secure: sic-non-secure@12100000 { ++ compatible = "syscon"; ++ reg = <0x12100000 0x10000>; ++ }; ++ ++ gsbi1: gsbi@12440000 { ++ compatible = "qcom,gsbi-v1.0.0"; ++ cell-index = <1>; ++ reg = <0x12440000 0x100>; ++ clocks = <&gcc GSBI1_H_CLK>; ++ clock-names = "iface"; ++ #address-cells = <1>; ++ #size-cells = <1>; ++ ranges; ++ status = "disabled"; ++ ++ syscon-tcsr = <&tcsr>; ++ ++ gsbi1_serial: serial@12450000 { ++ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; ++ reg = <0x12450000 0x100>, ++ <0x12400000 0x03>; ++ interrupts = ; ++ clocks = <&gcc GSBI1_UART_CLK>, <&gcc GSBI1_H_CLK>; ++ clock-names = "core", "iface"; ++ status = "disabled"; ++ }; ++ ++ gsbi1_i2c: i2c@12460000 { ++ compatible = "qcom,i2c-qup-v1.1.1"; ++ reg = <0x12460000 0x1000>; ++ interrupts = ; ++ clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>; ++ clock-names = "core", "iface"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "disabled"; ++ }; ++ }; ++ + gsbi2: gsbi@12480000 { + compatible = "qcom,gsbi-v1.0.0"; + cell-index = <2>; +@@ -368,6 +910,33 @@ + }; + }; + ++ gsbi6: gsbi@16500000 { ++ status = "disabled"; ++ compatible = "qcom,gsbi-v1.0.0"; ++ cell-index = <6>; ++ reg = <0x16500000 0x100>; ++ clocks = <&gcc GSBI6_H_CLK>; ++ clock-names = "iface"; ++ #address-cells = <1>; ++ #size-cells = <1>; ++ ranges; ++ ++ syscon-tcsr = <&tcsr>; ++ ++ gsbi6_i2c: i2c@16580000 { ++ compatible = "qcom,i2c-qup-v1.1.1"; ++ reg = <0x16580000 0x1000>; ++ interrupts = ; ++ ++ clocks = <&gcc GSBI6_QUP_CLK>, <&gcc GSBI6_H_CLK>; ++ clock-names = "core", "iface"; ++ status = "disabled"; ++ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ }; ++ }; ++ + gsbi7: gsbi@16600000 { + status = "disabled"; + compatible = "qcom,gsbi-v1.0.0"; +@@ -389,6 +958,19 @@ + clock-names = "core", "iface"; + status = "disabled"; + }; ++ ++ gsbi7_i2c: i2c@16680000 { ++ compatible = "qcom,i2c-qup-v1.1.1"; ++ reg = <0x16680000 0x1000>; ++ interrupts = ; ++ ++ clocks = <&gcc GSBI7_QUP_CLK>, <&gcc GSBI7_H_CLK>; ++ clock-names = "core", "iface"; ++ status = "disabled"; ++ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ }; + }; + + sata_phy: sata-phy@1b400000 { +@@ -478,6 +1060,95 @@ + #reset-cells = <1>; + }; + ++ sfpb_mutex_block: syscon@1200600 { ++ compatible = "syscon"; ++ reg = <0x01200600 0x100>; ++ }; ++ ++ hs_phy_0: hs_phy_0 { ++ compatible = "qcom,ipq806x-usb-phy-hs"; ++ reg = <0x110f8800 0x30>; ++ clocks = <&gcc USB30_0_UTMI_CLK>; ++ clock-names = "ref"; ++ #phy-cells = <0>; ++ }; ++ ++ ss_phy_0: ss_phy_0 { ++ compatible = "qcom,ipq806x-usb-phy-ss"; ++ reg = <0x110f8830 0x30>; ++ clocks = <&gcc USB30_0_MASTER_CLK>; ++ clock-names = "ref"; ++ #phy-cells = <0>; ++ }; ++ ++ usb3_0: usb3@110f8800 { ++ compatible = "qcom,dwc3", "syscon"; ++ #address-cells = <1>; ++ #size-cells = <1>; ++ reg = <0x110f8800 0x8000>; ++ clocks = <&gcc USB30_0_MASTER_CLK>; ++ clock-names = "core"; ++ ++ ranges; ++ ++ resets = <&gcc USB30_0_MASTER_RESET>; ++ reset-names = "master"; ++ ++ status = "disabled"; ++ ++ dwc3_0: dwc3@11000000 { ++ compatible = "snps,dwc3"; ++ reg = <0x11000000 0xcd00>; ++ interrupts = ; ++ phys = <&hs_phy_0>, <&ss_phy_0>; ++ phy-names = "usb2-phy", "usb3-phy"; ++ dr_mode = "host"; ++ snps,dis_u3_susphy_quirk; ++ }; ++ }; ++ ++ hs_phy_1: hs_phy_1 { ++ compatible = "qcom,ipq806x-usb-phy-hs"; ++ reg = <0x100f8800 0x30>; ++ clocks = <&gcc USB30_1_UTMI_CLK>; ++ clock-names = "ref"; ++ #phy-cells = <0>; ++ }; ++ ++ ss_phy_1: ss_phy_1 { ++ compatible = "qcom,ipq806x-usb-phy-ss"; ++ reg = <0x100f8830 0x30>; ++ clocks = <&gcc USB30_1_MASTER_CLK>; ++ clock-names = "ref"; ++ #phy-cells = <0>; ++ }; ++ ++ usb3_1: usb3@100f8800 { ++ compatible = "qcom,dwc3", "syscon"; ++ #address-cells = <1>; ++ #size-cells = <1>; ++ reg = <0x100f8800 0x8000>; ++ clocks = <&gcc USB30_1_MASTER_CLK>; ++ clock-names = "core"; ++ ++ ranges; ++ ++ resets = <&gcc USB30_1_MASTER_RESET>; ++ reset-names = "master"; ++ ++ status = "disabled"; ++ ++ dwc3_1: dwc3@10000000 { ++ compatible = "snps,dwc3"; ++ reg = <0x10000000 0xcd00>; ++ interrupts = ; ++ phys = <&hs_phy_1>, <&ss_phy_1>; ++ phy-names = "usb2-phy", "usb3-phy"; ++ dr_mode = "host"; ++ snps,dis_u3_susphy_quirk; ++ }; ++ }; ++ + pcie0: pci@1b500000 { + compatible = "qcom,pcie-ipq8064"; + reg = <0x1b500000 0x1000 +@@ -739,6 +1410,59 @@ + status = "disabled"; + }; + ++ adm_dma: dma@18300000 { ++ compatible = "qcom,adm"; ++ reg = <0x18300000 0x100000>; ++ interrupts = ; ++ #dma-cells = <1>; ++ ++ clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>; ++ clock-names = "core", "iface"; ++ ++ resets = <&gcc ADM0_RESET>, ++ <&gcc ADM0_PBUS_RESET>, ++ <&gcc ADM0_C0_RESET>, ++ <&gcc ADM0_C1_RESET>, ++ <&gcc ADM0_C2_RESET>; ++ reset-names = "clk", "pbus", "c0", "c1", "c2"; ++ qcom,ee = <0>; ++ ++ status = "disabled"; ++ }; ++ ++ nand_controller: nand-controller@1ac00000 { ++ compatible = "qcom,ipq806x-nand"; ++ reg = <0x1ac00000 0x800>; ++ ++ clocks = <&gcc EBI2_CLK>, ++ <&gcc EBI2_AON_CLK>; ++ clock-names = "core", "aon"; ++ ++ dmas = <&adm_dma 3>; ++ dma-names = "rxtx"; ++ qcom,cmd-crci = <15>; ++ qcom,data-crci = <3>; ++ ++ status = "disabled"; ++ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ }; ++ ++ mdio0: mdio@37000000 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ compatible = "qcom,ipq8064-mdio", "syscon"; ++ reg = <0x37000000 0x200000>; ++ resets = <&gcc GMAC_CORE1_RESET>; ++ reset-names = "stmmaceth"; ++ clocks = <&gcc GMAC_CORE1_CLK>; ++ clock-names = "stmmaceth"; ++ ++ status = "disabled"; ++ }; ++ + vsdcc_fixed: vsdcc-regulator { + compatible = "regulator-fixed"; + regulator-name = "SDCC Power"; +@@ -814,4 +1538,17 @@ + }; + }; + }; ++ ++ sfpb_mutex: sfpb-mutex { ++ compatible = "qcom,sfpb-mutex"; ++ syscon = <&sfpb_mutex_block 4 4>; ++ ++ #hwlock-cells = <1>; ++ }; ++ ++ smem { ++ compatible = "qcom,smem"; ++ memory-region = <&smem>; ++ hwlocks = <&sfpb_mutex 3>; ++ }; + }; diff --git a/target/linux/ipq806x/patches-5.15/084-ipq8064-v1.0-dtsi-cleanup.patch b/target/linux/ipq806x/patches-5.15/084-ipq8064-v1.0-dtsi-cleanup.patch new file mode 100644 index 0000000000..e5ea8e6393 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/084-ipq8064-v1.0-dtsi-cleanup.patch @@ -0,0 +1,89 @@ +This uses upstream qcom-ipq8064-v1.0.dtsi and modifies it by patches +instead of keeping a local version. +We drop partitions, LEDs and keys from the file as we will implement +them differently anyway. + +--- a/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi +@@ -42,16 +42,6 @@ + #size-cells = <1>; + spi-max-frequency = <50000000>; + reg = <0>; +- +- partition@0 { +- label = "rootfs"; +- reg = <0x0 0x1000000>; +- }; +- +- partition@1 { +- label = "scratch"; +- reg = <0x1000000 0x1000000>; +- }; + }; + }; + }; +@@ -64,64 +54,5 @@ + ports-implemented = <0x1>; + status = "ok"; + }; +- +- gpio_keys { +- compatible = "gpio-keys"; +- pinctrl-0 = <&buttons_pins>; +- pinctrl-names = "default"; +- +- button@1 { +- label = "reset"; +- linux,code = ; +- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; +- linux,input-type = <1>; +- debounce-interval = <60>; +- }; +- button@2 { +- label = "wps"; +- linux,code = ; +- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; +- linux,input-type = <1>; +- debounce-interval = <60>; +- }; +- }; +- +- leds { +- compatible = "gpio-leds"; +- pinctrl-0 = <&leds_pins>; +- pinctrl-names = "default"; +- +- led@7 { +- label = "led_usb1"; +- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; +- linux,default-trigger = "usbdev"; +- default-state = "off"; +- }; +- +- led@8 { +- label = "led_usb3"; +- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; +- linux,default-trigger = "usbdev"; +- default-state = "off"; +- }; +- +- led@9 { +- label = "status_led_fail"; +- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; +- default-state = "off"; +- }; +- +- led@26 { +- label = "sata_led"; +- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; +- default-state = "off"; +- }; +- +- led@53 { +- label = "status_led_pass"; +- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; +- default-state = "off"; +- }; +- }; + }; + }; diff --git a/target/linux/ipq806x/patches-5.15/085-ipq8064-v1.0-dtsi-additions.patch b/target/linux/ipq806x/patches-5.15/085-ipq8064-v1.0-dtsi-additions.patch new file mode 100644 index 0000000000..58f6a46e4f --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/085-ipq8064-v1.0-dtsi-additions.patch @@ -0,0 +1,14 @@ +This uses upstream qcom-ipq8064-v1.0.dtsi and modifies it by patches +instead of keeping a local version. This patch adds our local adjustments +for the (local) additional contents of qcom-ipq8064.dtsi + +--- a/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi +@@ -56,3 +56,7 @@ + }; + }; + }; ++ ++&CPU_SPC { ++ status = "okay"; ++}; diff --git a/target/linux/ipq806x/patches-5.15/086-ipq8064-fix-duplicate-node.patch b/target/linux/ipq806x/patches-5.15/086-ipq8064-fix-duplicate-node.patch new file mode 100644 index 0000000000..747fa8c019 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/086-ipq8064-fix-duplicate-node.patch @@ -0,0 +1,145 @@ +--- a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts ++++ b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts +@@ -24,73 +24,6 @@ + device_type = "memory"; + }; + +- mdio0: mdio-0 { +- status = "okay"; +- compatible = "virtual,mdio-gpio"; +- gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, +- <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; +- #address-cells = <1>; +- #size-cells = <0>; +- +- pinctrl-0 = <&mdio0_pins>; +- pinctrl-names = "default"; +- +- switch0: switch@10 { +- compatible = "qca,qca8337"; +- #address-cells = <1>; +- #size-cells = <0>; +- +- dsa,member = <0 0>; +- +- pinctrl-0 = <&sw0_reset_pin>; +- pinctrl-names = "default"; +- +- reset-gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>; +- reg = <0x10>; +- +- ports { +- #address-cells = <1>; +- #size-cells = <0>; +- +- switch0cpu: port@0 { +- reg = <0>; +- label = "cpu"; +- ethernet = <&gmac0>; +- phy-mode = "rgmii-id"; +- fixed-link { +- speed = <1000>; +- full-duplex; +- }; +- }; +- +- port@1 { +- reg = <1>; +- label = "sw1"; +- }; +- +- port@2 { +- reg = <2>; +- label = "sw2"; +- }; +- +- port@3 { +- reg = <3>; +- label = "sw3"; +- }; +- +- port@4 { +- reg = <4>; +- label = "sw4"; +- }; +- +- port@5 { +- reg = <5>; +- label = "sw5"; +- }; +- }; +- }; +- }; +- + mdio1: mdio-1 { + status = "okay"; + compatible = "virtual,mdio-gpio"; +@@ -216,6 +149,68 @@ + }; + }; + ++&mdio0 { ++ status = "okay"; ++ ++ pinctrl-0 = <&mdio0_pins>; ++ pinctrl-names = "default"; ++ ++ switch0: switch@10 { ++ compatible = "qca,qca8337"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ dsa,member = <0 0>; ++ ++ pinctrl-0 = <&sw0_reset_pin>; ++ pinctrl-names = "default"; ++ ++ reset-gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>; ++ reg = <0x10>; ++ ++ ports { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ switch0cpu: port@0 { ++ reg = <0>; ++ label = "cpu"; ++ ethernet = <&gmac0>; ++ phy-mode = "rgmii-id"; ++ fixed-link { ++ speed = <1000>; ++ full-duplex; ++ }; ++ }; ++ ++ port@1 { ++ reg = <1>; ++ label = "sw1"; ++ }; ++ ++ port@2 { ++ reg = <2>; ++ label = "sw2"; ++ }; ++ ++ port@3 { ++ reg = <3>; ++ label = "sw3"; ++ }; ++ ++ port@4 { ++ reg = <4>; ++ label = "sw4"; ++ }; ++ ++ port@5 { ++ reg = <5>; ++ label = "sw5"; ++ }; ++ }; ++ }; ++}; ++ + &gmac0 { + status = "okay"; + diff --git a/target/linux/ipq806x/patches-5.15/093-drivers-cpufreq-qcom-cpufreq-nvmem-support-specific-.patch b/target/linux/ipq806x/patches-5.15/093-drivers-cpufreq-qcom-cpufreq-nvmem-support-specific-.patch new file mode 100644 index 0000000000..19c3d096c4 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/093-drivers-cpufreq-qcom-cpufreq-nvmem-support-specific-.patch @@ -0,0 +1,51 @@ +From a206d4061f1cc2c5cd17ee45c53a0ba711e48e6d Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Sun, 7 Feb 2021 16:42:52 +0100 +Subject: [PATCH 3/3] drivers: cpufreq: qcom-cpufreq-nvmem: support specific + cpufreq driver + +Add support for specific cpufreq driver for qcom-cpufreq-nvmem driver. + +Signed-off-by: Ansuel Smith +--- + drivers/cpufreq/qcom-cpufreq-nvmem.c | 15 +++++++++++++++ + 1 file changed, 15 insertions(+) + +--- a/drivers/cpufreq/qcom-cpufreq-nvmem.c ++++ b/drivers/cpufreq/qcom-cpufreq-nvmem.c +@@ -52,6 +52,7 @@ struct qcom_cpufreq_match_data { + char **pvs_name, + struct qcom_cpufreq_drv *drv); + const char **genpd_names; ++ const char *cpufreq_driver; + }; + + struct qcom_cpufreq_drv { +@@ -250,6 +251,7 @@ static const struct qcom_cpufreq_match_d + + static const struct qcom_cpufreq_match_data match_data_krait = { + .get_version = qcom_cpufreq_krait_name_version, ++ .cpufreq_driver = "krait-cpufreq", + }; + + static const char *qcs404_genpd_names[] = { "cpr", NULL }; +@@ -385,6 +387,19 @@ static int qcom_cpufreq_probe(struct pla + } + } + ++ if (drv->data->cpufreq_driver) { ++ cpufreq_dt_pdev = platform_device_register_simple( ++ drv->data->cpufreq_driver, -1, NULL, 0); ++ if (!IS_ERR(cpufreq_dt_pdev)) { ++ platform_set_drvdata(pdev, drv); ++ return 0; ++ } else { ++ dev_err(cpu_dev, ++ "Failed to register dedicated %s cpufreq\n", ++ drv->data->cpufreq_driver); ++ } ++ } ++ + cpufreq_dt_pdev = platform_device_register_simple("cpufreq-dt", -1, + NULL, 0); + if (!IS_ERR(cpufreq_dt_pdev)) { diff --git a/target/linux/ipq806x/patches-5.15/097-1-ipq806x-gcc-add-missing-clk-flag.patch b/target/linux/ipq806x/patches-5.15/097-1-ipq806x-gcc-add-missing-clk-flag.patch new file mode 100644 index 0000000000..3b4900fafb --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/097-1-ipq806x-gcc-add-missing-clk-flag.patch @@ -0,0 +1,99 @@ +From 0af44917941cbfecdc86bb9bf05ff01d22a88973 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Sun, 7 Feb 2021 16:52:56 +0100 +Subject: [PATCH 1/4] ipq806x: gcc: add missing clk flag + +Some flag are missing from the original code. +These clk can't be set using the protected-clock proprities as they +cause the malfunction of the serial interface. +These clks are needed for the rpm interface to work proprely or the +cpu regulators starts to fail as soon as they are disabled by the +kernel. + +Signed-off-by: Ansuel Smith +--- + drivers/clk/qcom/gcc-ipq806x.c | 19 +++++++++++++------ + 1 file changed, 13 insertions(+), 6 deletions(-) + +--- a/drivers/clk/qcom/gcc-ipq806x.c ++++ b/drivers/clk/qcom/gcc-ipq806x.c +@@ -65,6 +65,7 @@ static struct clk_pll pll3 = { + .parent_names = (const char *[]){ "pxo" }, + .num_parents = 1, + .ops = &clk_pll_ops, ++ .flags = CLK_IS_CRITICAL, + }, + }; + +@@ -782,7 +783,7 @@ static struct clk_rcg gsbi4_qup_src = { + .parent_names = gcc_pxo_pll8, + .num_parents = 2, + .ops = &clk_rcg_ops, +- .flags = CLK_SET_PARENT_GATE, ++ .flags = CLK_SET_PARENT_GATE | CLK_IGNORE_UNUSED, + }, + }, + }; +@@ -798,7 +799,7 @@ static struct clk_branch gsbi4_qup_clk = + .parent_names = (const char *[]){ "gsbi4_qup_src" }, + .num_parents = 1, + .ops = &clk_branch_ops, +- .flags = CLK_SET_RATE_PARENT, ++ .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED, + }, + }, + }; +@@ -880,7 +881,7 @@ static struct clk_rcg gsbi6_qup_src = { + .parent_names = gcc_pxo_pll8, + .num_parents = 2, + .ops = &clk_rcg_ops, +- .flags = CLK_SET_PARENT_GATE, ++ .flags = CLK_SET_PARENT_GATE | CLK_IGNORE_UNUSED, + }, + }, + }; +@@ -945,7 +946,7 @@ static struct clk_branch gsbi7_qup_clk = + .parent_names = (const char *[]){ "gsbi7_qup_src" }, + .num_parents = 1, + .ops = &clk_branch_ops, +- .flags = CLK_SET_RATE_PARENT, ++ .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED, + }, + }, + }; +@@ -991,6 +992,7 @@ static struct clk_branch gsbi4_h_clk = { + .hw.init = &(struct clk_init_data){ + .name = "gsbi4_h_clk", + .ops = &clk_branch_ops, ++ .flags = CLK_IGNORE_UNUSED, + }, + }, + }; +@@ -1424,6 +1426,7 @@ static struct clk_rcg tsif_ref_src = { + .parent_names = gcc_pxo_pll8, + .num_parents = 2, + .ops = &clk_rcg_ops, ++ .flags = CLK_SET_RATE_GATE, + }, + } + }; +@@ -2694,7 +2697,8 @@ static struct clk_dyn_rcg ubi32_core1_sr + .parent_names = gcc_pxo_pll8_pll14_pll18_pll0, + .num_parents = 5, + .ops = &clk_dyn_rcg_ops, +- .flags = CLK_SET_RATE_PARENT | CLK_GET_RATE_NOCACHE, ++ .flags = CLK_SET_RATE_PARENT | CLK_GET_RATE_NOCACHE | ++ CLK_IGNORE_UNUSED, + }, + }, + }; +@@ -2747,7 +2751,8 @@ static struct clk_dyn_rcg ubi32_core2_sr + .parent_names = gcc_pxo_pll8_pll14_pll18_pll0, + .num_parents = 5, + .ops = &clk_dyn_rcg_ops, +- .flags = CLK_SET_RATE_PARENT | CLK_GET_RATE_NOCACHE, ++ .flags = CLK_SET_RATE_PARENT | CLK_GET_RATE_NOCACHE | ++ CLK_IGNORE_UNUSED, + }, + }, + }; diff --git a/target/linux/ipq806x/patches-5.15/097-2-ipq806x-lcc-add-missing-reset.patch b/target/linux/ipq806x/patches-5.15/097-2-ipq806x-lcc-add-missing-reset.patch new file mode 100644 index 0000000000..cd2cb33356 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/097-2-ipq806x-lcc-add-missing-reset.patch @@ -0,0 +1,59 @@ +From 3a5f1793c0bf4a6b536751886b0a44589fe05f35 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Sun, 7 Feb 2021 17:00:07 +0100 +Subject: [PATCH 2/4] ipq806x: lcc: add missing reset + +Add missing reset for ipq806x lcc clk + +Signed-off-by: Ansuel Smith +--- + drivers/clk/qcom/lcc-ipq806x.c | 8 ++++++++ + include/dt-bindings/clock/qcom,lcc-ipq806x.h | 1 + + 2 files changed, 9 insertions(+) + +--- a/drivers/clk/qcom/lcc-ipq806x.c ++++ b/drivers/clk/qcom/lcc-ipq806x.c +@@ -12,6 +12,7 @@ + #include + #include + #include ++#include + + #include + +@@ -22,6 +23,7 @@ + #include "clk-branch.h" + #include "clk-regmap-divider.h" + #include "clk-regmap-mux.h" ++#include "reset.h" + + static struct clk_pll pll4 = { + .l_reg = 0x4, +@@ -39,6 +41,10 @@ static struct clk_pll pll4 = { + }, + }; + ++static const struct qcom_reset_map lcc_ipq806x_resets[] = { ++ [LCC_PCM_RESET] = { 0x54, 13 }, ++}; ++ + static const struct pll_config pll4_config = { + .l = 0xf, + .m = 0x91, +@@ -417,6 +423,8 @@ static const struct qcom_cc_desc lcc_ipq + .config = &lcc_ipq806x_regmap_config, + .clks = lcc_ipq806x_clks, + .num_clks = ARRAY_SIZE(lcc_ipq806x_clks), ++ .resets = lcc_ipq806x_resets, ++ .num_resets = ARRAY_SIZE(lcc_ipq806x_resets), + }; + + static const struct of_device_id lcc_ipq806x_match_table[] = { +--- a/include/dt-bindings/clock/qcom,lcc-ipq806x.h ++++ b/include/dt-bindings/clock/qcom,lcc-ipq806x.h +@@ -19,4 +19,5 @@ + #define SPDIF_CLK 10 + #define AHBIX_CLK 11 + ++#define LCC_PCM_RESET 0 + #endif diff --git a/target/linux/ipq806x/patches-5.15/097-3-clk-qcom-krait-add-missing-enable-disable.patch b/target/linux/ipq806x/patches-5.15/097-3-clk-qcom-krait-add-missing-enable-disable.patch new file mode 100644 index 0000000000..bf1c1a4a2f --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/097-3-clk-qcom-krait-add-missing-enable-disable.patch @@ -0,0 +1,57 @@ +From f8fdbecdaca97f0f2eebd77256e2eca4a8da6c39 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Sun, 7 Feb 2021 17:08:16 +0100 +Subject: [PATCH 3/4] clk: qcom: krait: add missing enable disable + +Add missing enable disable mux function. Add extra check to +div2_round_rate. + +Signed-off-by: Ansuel Smith +--- + drivers/clk/qcom/clk-krait.c | 27 +++++++++++++++++++++++++-- + 1 file changed, 25 insertions(+), 2 deletions(-) + +--- a/drivers/clk/qcom/clk-krait.c ++++ b/drivers/clk/qcom/clk-krait.c +@@ -68,7 +68,25 @@ static u8 krait_mux_get_parent(struct cl + return clk_mux_val_to_index(hw, mux->parent_map, 0, sel); + } + ++static int krait_mux_enable(struct clk_hw *hw) ++{ ++ struct krait_mux_clk *mux = to_krait_mux_clk(hw); ++ ++ __krait_mux_set_sel(mux, mux->en_mask); ++ ++ return 0; ++} ++ ++static void krait_mux_disable(struct clk_hw *hw) ++{ ++ struct krait_mux_clk *mux = to_krait_mux_clk(hw); ++ ++ __krait_mux_set_sel(mux, mux->safe_sel); ++} ++ + const struct clk_ops krait_mux_clk_ops = { ++ .enable = krait_mux_enable, ++ .disable = krait_mux_disable, + .set_parent = krait_mux_set_parent, + .get_parent = krait_mux_get_parent, + .determine_rate = __clk_mux_determine_rate_closest, +@@ -79,8 +97,13 @@ EXPORT_SYMBOL_GPL(krait_mux_clk_ops); + static long krait_div2_round_rate(struct clk_hw *hw, unsigned long rate, + unsigned long *parent_rate) + { +- *parent_rate = clk_hw_round_rate(clk_hw_get_parent(hw), rate * 2); +- return DIV_ROUND_UP(*parent_rate, 2); ++ struct clk_hw *hw_parent = clk_hw_get_parent(hw); ++ ++ if (hw_parent) { ++ *parent_rate = clk_hw_round_rate(hw_parent, rate * 2); ++ return DIV_ROUND_UP(*parent_rate, 2); ++ } else ++ return -1; + } + + static int krait_div2_set_rate(struct clk_hw *hw, unsigned long rate, diff --git a/target/linux/ipq806x/patches-5.15/097-4-ipq806x-gcc-add-missing-clk-and-reset-for-crypto-eng.patch b/target/linux/ipq806x/patches-5.15/097-4-ipq806x-gcc-add-missing-clk-and-reset-for-crypto-eng.patch new file mode 100644 index 0000000000..d1e047cabf --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/097-4-ipq806x-gcc-add-missing-clk-and-reset-for-crypto-eng.patch @@ -0,0 +1,372 @@ +From 22a0f55b0e505fbbbb680e451a62878bc97f7ff1 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Sun, 7 Feb 2021 17:23:38 +0100 +Subject: [PATCH 4/4] ipq806x: gcc: add missing clk and reset for crypto engine + +Add missing clk and reset needed for nss additional core and crypto +engine. + +Signed-off-by: Ansuel Smith +--- + drivers/clk/qcom/gcc-ipq806x.c | 250 +++++++++++++++++++ + include/dt-bindings/clock/qcom,gcc-ipq806x.h | 5 +- + include/dt-bindings/reset/qcom,gcc-ipq806x.h | 5 + + 3 files changed, 259 insertions(+), 1 deletion(-) + +--- a/drivers/clk/qcom/gcc-ipq806x.c ++++ b/drivers/clk/qcom/gcc-ipq806x.c +@@ -223,7 +223,9 @@ static struct clk_regmap pll14_vote = { + + static struct pll_freq_tbl pll18_freq_tbl[] = { + NSS_PLL_RATE(550000000, 44, 0, 1, 0x01495625), ++ NSS_PLL_RATE(600000000, 48, 0, 1, 0x01495625), + NSS_PLL_RATE(733000000, 58, 16, 25, 0x014b5625), ++ NSS_PLL_RATE(800000000, 64, 0, 1, 0x01495625), + }; + + static struct clk_pll pll18 = { +@@ -245,6 +247,22 @@ static struct clk_pll pll18 = { + }, + }; + ++static struct clk_pll pll11 = { ++ .l_reg = 0x3184, ++ .m_reg = 0x3188, ++ .n_reg = 0x318c, ++ .config_reg = 0x3194, ++ .mode_reg = 0x3180, ++ .status_reg = 0x3198, ++ .status_bit = 16, ++ .clkr.hw.init = &(struct clk_init_data){ ++ .name = "pll11", ++ .parent_names = (const char *[]){ "pxo" }, ++ .num_parents = 1, ++ .ops = &clk_pll_ops, ++ }, ++}; ++ + enum { + P_PXO, + P_PLL8, +@@ -253,6 +271,7 @@ enum { + P_CXO, + P_PLL14, + P_PLL18, ++ P_PLL11, + }; + + static const struct parent_map gcc_pxo_pll8_map[] = { +@@ -320,6 +339,42 @@ static const char * const gcc_pxo_pll8_p + "pll18", + }; + ++static const struct parent_map gcc_pxo_pll8_pll0_pll14_pll18_pll11_map[] = { ++ { P_PXO, 0 }, ++ { P_PLL8, 4 }, ++ { P_PLL0, 2 }, ++ { P_PLL14, 5 }, ++ { P_PLL18, 1 }, ++ { P_PLL11, 3 }, ++}; ++ ++static const char *gcc_pxo_pll8_pll0_pll14_pll18_pll11[] = { ++ "pxo", ++ "pll8_vote", ++ "pll0_vote", ++ "pll14", ++ "pll18", ++ "pll11" ++}; ++ ++static const struct parent_map gcc_pxo_pll3_pll0_pll14_pll18_pll11_map[] = { ++ { P_PXO, 0 }, ++ { P_PLL3, 6 }, ++ { P_PLL0, 2 }, ++ { P_PLL14, 5 }, ++ { P_PLL18, 1 }, ++ { P_PLL11, 3 }, ++}; ++ ++static const char *gcc_pxo_pll3_pll0_pll14_pll18_pll11[] = { ++ "pxo", ++ "pll3", ++ "pll0_vote", ++ "pll14", ++ "pll18", ++ "pll11" ++}; ++ + static struct freq_tbl clk_tbl_gsbi_uart[] = { + { 1843200, P_PLL8, 2, 6, 625 }, + { 3686400, P_PLL8, 2, 12, 625 }, +@@ -1261,6 +1316,7 @@ static const struct freq_tbl clk_tbl_sdc + { 20210000, P_PLL8, 1, 1, 19 }, + { 24000000, P_PLL8, 4, 1, 4 }, + { 48000000, P_PLL8, 4, 1, 2 }, ++ { 52000000, P_PLL8, 1, 2, 15 }, /* 51.2 Mhz */ + { 64000000, P_PLL8, 3, 1, 2 }, + { 96000000, P_PLL8, 4, 0, 0 }, + { 192000000, P_PLL8, 2, 0, 0 }, +@@ -2645,7 +2701,9 @@ static const struct freq_tbl clk_tbl_nss + { 110000000, P_PLL18, 1, 1, 5 }, + { 275000000, P_PLL18, 2, 0, 0 }, + { 550000000, P_PLL18, 1, 0, 0 }, ++ { 600000000, P_PLL18, 1, 0, 0 }, + { 733000000, P_PLL18, 1, 0, 0 }, ++ { 800000000, P_PLL18, 1, 0, 0 }, + { } + }; + +@@ -2757,6 +2815,186 @@ static struct clk_dyn_rcg ubi32_core2_sr + }, + }; + ++static const struct freq_tbl clk_tbl_ce5_core[] = { ++ { 150000000, P_PLL3, 8, 1, 1 }, ++ { 213200000, P_PLL11, 5, 1, 1 }, ++ { } ++}; ++ ++static struct clk_dyn_rcg ce5_core_src = { ++ .ns_reg[0] = 0x36C4, ++ .ns_reg[1] = 0x36C8, ++ .bank_reg = 0x36C0, ++ .s[0] = { ++ .src_sel_shift = 0, ++ .parent_map = gcc_pxo_pll3_pll0_pll14_pll18_pll11_map, ++ }, ++ .s[1] = { ++ .src_sel_shift = 0, ++ .parent_map = gcc_pxo_pll3_pll0_pll14_pll18_pll11_map, ++ }, ++ .p[0] = { ++ .pre_div_shift = 3, ++ .pre_div_width = 4, ++ }, ++ .p[1] = { ++ .pre_div_shift = 3, ++ .pre_div_width = 4, ++ }, ++ .mux_sel_bit = 0, ++ .freq_tbl = clk_tbl_ce5_core, ++ .clkr = { ++ .enable_reg = 0x36C0, ++ .enable_mask = BIT(1), ++ .hw.init = &(struct clk_init_data){ ++ .name = "ce5_core_src", ++ .parent_names = gcc_pxo_pll3_pll0_pll14_pll18_pll11, ++ .num_parents = 6, ++ .ops = &clk_dyn_rcg_ops, ++ }, ++ }, ++}; ++ ++static struct clk_branch ce5_core_clk = { ++ .halt_reg = 0x2FDC, ++ .halt_bit = 5, ++ .hwcg_reg = 0x36CC, ++ .hwcg_bit = 6, ++ .clkr = { ++ .enable_reg = 0x36CC, ++ .enable_mask = BIT(4), ++ .hw.init = &(struct clk_init_data){ ++ .name = "ce5_core_clk", ++ .parent_names = (const char *[]){ ++ "ce5_core_src", ++ }, ++ .num_parents = 1, ++ .ops = &clk_branch_ops, ++ .flags = CLK_SET_RATE_PARENT, ++ }, ++ }, ++}; ++ ++static const struct freq_tbl clk_tbl_ce5_a_clk[] = { ++ { 160000000, P_PLL0, 5, 1, 1 }, ++ { 213200000, P_PLL11, 5, 1, 1 }, ++ { } ++}; ++ ++static struct clk_dyn_rcg ce5_a_clk_src = { ++ .ns_reg[0] = 0x3d84, ++ .ns_reg[1] = 0x3d88, ++ .bank_reg = 0x3d80, ++ .s[0] = { ++ .src_sel_shift = 0, ++ .parent_map = gcc_pxo_pll8_pll0_pll14_pll18_pll11_map, ++ }, ++ .s[1] = { ++ .src_sel_shift = 0, ++ .parent_map = gcc_pxo_pll8_pll0_pll14_pll18_pll11_map, ++ }, ++ .p[0] = { ++ .pre_div_shift = 3, ++ .pre_div_width = 4, ++ }, ++ .p[1] = { ++ .pre_div_shift = 3, ++ .pre_div_width = 4, ++ }, ++ .mux_sel_bit = 0, ++ .freq_tbl = clk_tbl_ce5_a_clk, ++ .clkr = { ++ .enable_reg = 0x3d80, ++ .enable_mask = BIT(1), ++ .hw.init = &(struct clk_init_data){ ++ .name = "ce5_a_clk_src", ++ .parent_names = gcc_pxo_pll8_pll0_pll14_pll18_pll11, ++ .num_parents = 6, ++ .ops = &clk_dyn_rcg_ops, ++ }, ++ }, ++}; ++ ++static struct clk_branch ce5_a_clk = { ++ .halt_reg = 0x3c20, ++ .halt_bit = 12, ++ .hwcg_reg = 0x3d8c, ++ .hwcg_bit = 6, ++ .clkr = { ++ .enable_reg = 0x3d8c, ++ .enable_mask = BIT(4), ++ .hw.init = &(struct clk_init_data){ ++ .name = "ce5_a_clk", ++ .parent_names = (const char *[]){ ++ "ce5_a_clk_src", ++ }, ++ .num_parents = 1, ++ .ops = &clk_branch_ops, ++ .flags = CLK_SET_RATE_PARENT, ++ }, ++ }, ++}; ++ ++static const struct freq_tbl clk_tbl_ce5_h_clk[] = { ++ { 160000000, P_PLL0, 5, 1, 1 }, ++ { 213200000, P_PLL11, 5, 1, 1 }, ++ { } ++}; ++ ++static struct clk_dyn_rcg ce5_h_clk_src = { ++ .ns_reg[0] = 0x3c64, ++ .ns_reg[1] = 0x3c68, ++ .bank_reg = 0x3c60, ++ .s[0] = { ++ .src_sel_shift = 0, ++ .parent_map = gcc_pxo_pll8_pll0_pll14_pll18_pll11_map, ++ }, ++ .s[1] = { ++ .src_sel_shift = 0, ++ .parent_map = gcc_pxo_pll8_pll0_pll14_pll18_pll11_map, ++ }, ++ .p[0] = { ++ .pre_div_shift = 3, ++ .pre_div_width = 4, ++ }, ++ .p[1] = { ++ .pre_div_shift = 3, ++ .pre_div_width = 4, ++ }, ++ .mux_sel_bit = 0, ++ .freq_tbl = clk_tbl_ce5_h_clk, ++ .clkr = { ++ .enable_reg = 0x3c60, ++ .enable_mask = BIT(1), ++ .hw.init = &(struct clk_init_data){ ++ .name = "ce5_h_clk_src", ++ .parent_names = gcc_pxo_pll8_pll0_pll14_pll18_pll11, ++ .num_parents = 6, ++ .ops = &clk_dyn_rcg_ops, ++ }, ++ }, ++}; ++ ++static struct clk_branch ce5_h_clk = { ++ .halt_reg = 0x3c20, ++ .halt_bit = 11, ++ .hwcg_reg = 0x3c6c, ++ .hwcg_bit = 6, ++ .clkr = { ++ .enable_reg = 0x3c6c, ++ .enable_mask = BIT(4), ++ .hw.init = &(struct clk_init_data){ ++ .name = "ce5_h_clk", ++ .parent_names = (const char *[]){ ++ "ce5_h_clk_src", ++ }, ++ .num_parents = 1, ++ .ops = &clk_branch_ops, ++ .flags = CLK_SET_RATE_PARENT, ++ }, ++ }, ++}; ++ + static struct clk_regmap *gcc_ipq806x_clks[] = { + [PLL0] = &pll0.clkr, + [PLL0_VOTE] = &pll0_vote, +@@ -2764,6 +3002,7 @@ static struct clk_regmap *gcc_ipq806x_cl + [PLL4_VOTE] = &pll4_vote, + [PLL8] = &pll8.clkr, + [PLL8_VOTE] = &pll8_vote, ++ [PLL11] = &pll11.clkr, + [PLL14] = &pll14.clkr, + [PLL14_VOTE] = &pll14_vote, + [PLL18] = &pll18.clkr, +@@ -2878,6 +3117,12 @@ static struct clk_regmap *gcc_ipq806x_cl + [PLL9] = &hfpll0.clkr, + [PLL10] = &hfpll1.clkr, + [PLL12] = &hfpll_l2.clkr, ++ [CE5_A_CLK_SRC] = &ce5_a_clk_src.clkr, ++ [CE5_A_CLK] = &ce5_a_clk.clkr, ++ [CE5_H_CLK_SRC] = &ce5_h_clk_src.clkr, ++ [CE5_H_CLK] = &ce5_h_clk.clkr, ++ [CE5_CORE_CLK_SRC] = &ce5_core_src.clkr, ++ [CE5_CORE_CLK] = &ce5_core_clk.clkr, + }; + + static const struct qcom_reset_map gcc_ipq806x_resets[] = { +@@ -3009,6 +3254,11 @@ static const struct qcom_reset_map gcc_i + [GMAC_CORE3_RESET] = { 0x3cfc, 0 }, + [GMAC_CORE4_RESET] = { 0x3d1c, 0 }, + [GMAC_AHB_RESET] = { 0x3e24, 0 }, ++ [CRYPTO_ENG1_RESET] = { 0x3e00, 0}, ++ [CRYPTO_ENG2_RESET] = { 0x3e04, 0}, ++ [CRYPTO_ENG3_RESET] = { 0x3e08, 0}, ++ [CRYPTO_ENG4_RESET] = { 0x3e0c, 0}, ++ [CRYPTO_AHB_RESET] = { 0x3e10, 0}, + [NSS_CH0_RST_RX_CLK_N_RESET] = { 0x3b60, 0 }, + [NSS_CH0_RST_TX_CLK_N_RESET] = { 0x3b60, 1 }, + [NSS_CH0_RST_RX_125M_N_RESET] = { 0x3b60, 2 }, +--- a/include/dt-bindings/clock/qcom,gcc-ipq806x.h ++++ b/include/dt-bindings/clock/qcom,gcc-ipq806x.h +@@ -240,7 +240,7 @@ + #define PLL14 232 + #define PLL14_VOTE 233 + #define PLL18 234 +-#define CE5_SRC 235 ++#define CE5_A_CLK 235 + #define CE5_H_CLK 236 + #define CE5_CORE_CLK 237 + #define CE3_SLEEP_CLK 238 +@@ -283,5 +283,8 @@ + #define EBI2_AON_CLK 281 + #define NSSTCM_CLK_SRC 282 + #define NSSTCM_CLK 283 ++#define CE5_A_CLK_SRC 285 ++#define CE5_H_CLK_SRC 286 ++#define CE5_CORE_CLK_SRC 287 + + #endif +--- a/include/dt-bindings/reset/qcom,gcc-ipq806x.h ++++ b/include/dt-bindings/reset/qcom,gcc-ipq806x.h +@@ -163,5 +163,10 @@ + #define NSS_CAL_PRBS_RST_N_RESET 154 + #define NSS_LCKDT_RST_N_RESET 155 + #define NSS_SRDS_N_RESET 156 ++#define CRYPTO_ENG1_RESET 157 ++#define CRYPTO_ENG2_RESET 158 ++#define CRYPTO_ENG3_RESET 159 ++#define CRYPTO_ENG4_RESET 160 ++#define CRYPTO_AHB_RESET 161 + + #endif diff --git a/target/linux/ipq806x/patches-5.15/098-1-cpufreq-add-Krait-dedicated-scaling-driver.patch b/target/linux/ipq806x/patches-5.15/098-1-cpufreq-add-Krait-dedicated-scaling-driver.patch new file mode 100644 index 0000000000..769686220b --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/098-1-cpufreq-add-Krait-dedicated-scaling-driver.patch @@ -0,0 +1,681 @@ +From cc41a266280cad0b55319e614167c88dff344248 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Sat, 22 Feb 2020 16:33:10 +0100 +Subject: [PATCH 1/8] cpufreq: add Krait dedicated scaling driver + +This new driver is based on generic cpufreq-dt driver. +Krait SoCs have 2-4 cpu and one shared L2 cache that can +operate at different frequency based on the maximum cpu clk +across all core. +L2 frequency and voltage are scaled on every frequency change +if needed. On Krait SoCs is present a bug that can cause +transition problem between frequency bin, to workaround this +on more than one transition, the L2 frequency is first set to the +base rate and then to the target rate. +The L2 frequency use the OPP framework and use the opp-level +bindings to link the l2 freq to different cpu freq. This is needed +as the Krait l2 clk are note mapped 1:1 to the core clks and some +of the l2 clk is set based on a range of the cpu clks. If the driver +find a broken config (for example no opp-level set) the l2 scaling is +skipped. + +Signed-off-by: Ansuel Smith +--- + drivers/cpufreq/Kconfig.arm | 14 +- + drivers/cpufreq/Makefile | 2 + + drivers/cpufreq/qcom-cpufreq-krait.c | 589 +++++++++++++++++++++++++++ + 3 files changed, 604 insertions(+), 1 deletion(-) + create mode 100644 drivers/cpufreq/qcom-cpufreq-krait.c + +--- a/drivers/cpufreq/Kconfig.arm ++++ b/drivers/cpufreq/Kconfig.arm +@@ -150,6 +150,18 @@ config ARM_QCOM_CPUFREQ_HW + The driver implements the cpufreq interface for this HW engine. + Say Y if you want to support CPUFreq HW. + ++config ARM_QCOM_CPUFREQ_KRAIT ++ tristate "CPU Frequency scaling support for Krait SoCs" ++ depends on ARCH_QCOM || COMPILE_TEST ++ select PM_OPP ++ select ARM_QCOM_CPUFREQ_NVMEM ++ help ++ This adds the CPUFreq driver for Qualcomm Krait SoC based boards. ++ This scale the cache clk and regulator based on the different cpu ++ clks when scaling the different cores clk. ++ ++ If in doubt, say N. ++ + config ARM_RASPBERRYPI_CPUFREQ + tristate "Raspberry Pi cpufreq support" + depends on CLK_RASPBERRYPI || COMPILE_TEST +@@ -339,4 +351,4 @@ config ARM_PXA2xx_CPUFREQ + help + This add the CPUFreq driver support for Intel PXA2xx SOCs. + +- If in doubt, say N. ++ If in doubt, say N. +\ No newline at end of file +--- a/drivers/cpufreq/Makefile ++++ b/drivers/cpufreq/Makefile +@@ -63,6 +63,7 @@ obj-$(CONFIG_ARM_PXA2xx_CPUFREQ) += pxa2 + obj-$(CONFIG_PXA3xx) += pxa3xx-cpufreq.o + obj-$(CONFIG_ARM_QCOM_CPUFREQ_HW) += qcom-cpufreq-hw.o + obj-$(CONFIG_ARM_QCOM_CPUFREQ_NVMEM) += qcom-cpufreq-nvmem.o ++obj-$(CONFIG_ARM_QCOM_CPUFREQ_KRAIT) += qcom-cpufreq-krait.o + obj-$(CONFIG_ARM_RASPBERRYPI_CPUFREQ) += raspberrypi-cpufreq.o + obj-$(CONFIG_ARM_S3C2410_CPUFREQ) += s3c2410-cpufreq.o + obj-$(CONFIG_ARM_S3C2412_CPUFREQ) += s3c2412-cpufreq.o +@@ -86,6 +87,7 @@ obj-$(CONFIG_ARM_TEGRA186_CPUFREQ) += te + obj-$(CONFIG_ARM_TEGRA194_CPUFREQ) += tegra194-cpufreq.o + obj-$(CONFIG_ARM_TI_CPUFREQ) += ti-cpufreq.o + obj-$(CONFIG_ARM_VEXPRESS_SPC_CPUFREQ) += vexpress-spc-cpufreq.o ++obj-$(CONFIG_ARM_KRAIT_CPUFREQ) += krait-cpufreq.o + + + ################################################################################## +--- /dev/null ++++ b/drivers/cpufreq/qcom-cpufreq-krait.c +@@ -0,0 +1,603 @@ ++// SPDX-License-Identifier: GPL-2.0 ++ ++#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include "cpufreq-dt.h" ++ ++static struct platform_device *l2_pdev; ++ ++struct private_data { ++ struct opp_table *opp_table; ++ struct device *cpu_dev; ++ const char *reg_name; ++ bool have_static_opps; ++}; ++ ++static int set_target(struct cpufreq_policy *policy, unsigned int index) ++{ ++ struct private_data *priv = policy->driver_data; ++ unsigned long freq = policy->freq_table[index].frequency; ++ unsigned long target_freq = freq * 1000; ++ struct dev_pm_opp *opp; ++ unsigned int level; ++ int cpu, ret; ++ ++ if (l2_pdev) { ++ int policy_cpu = policy->cpu; ++ ++ /* find the max freq across all core */ ++ for_each_present_cpu(cpu) ++ if (cpu != policy_cpu) ++ target_freq = max( ++ target_freq, ++ (unsigned long)cpufreq_quick_get(cpu)); ++ ++ opp = dev_pm_opp_find_freq_exact(priv->cpu_dev, target_freq, ++ true); ++ if (IS_ERR(opp)) { ++ dev_err(&l2_pdev->dev, "failed to find OPP for %ld\n", ++ target_freq); ++ return PTR_ERR(opp); ++ } ++ level = dev_pm_opp_get_level(opp); ++ dev_pm_opp_put(opp); ++ ++ /* ++ * Hardware constraint: ++ * Krait CPU cannot operate at 384MHz with L2 at 1Ghz. ++ * Assume index 0 with the idle freq and level > 0 as ++ * any L2 freq > 384MHz. ++ * Skip CPU freq change in this corner case. ++ */ ++ if (unlikely(index == 0 && level != 0)) { ++ dev_err(priv->cpu_dev, "Krait CPU can't operate at idle freq with L2 at 1GHz"); ++ return -EINVAL; ++ } ++ ++ opp = dev_pm_opp_find_level_exact(&l2_pdev->dev, level); ++ if (IS_ERR(opp)) { ++ dev_err(&l2_pdev->dev, ++ "failed to find level OPP for %d\n", level); ++ return PTR_ERR(opp); ++ } ++ target_freq = dev_pm_opp_get_freq(opp); ++ dev_pm_opp_put(opp); ++ ++ ret = dev_pm_opp_set_rate(&l2_pdev->dev, target_freq); ++ if (ret) ++ return ret; ++ } ++ ++ ret = dev_pm_opp_set_rate(priv->cpu_dev, freq * 1000); ++ if (ret) ++ return ret; ++ ++ arch_set_freq_scale(policy->related_cpus, freq, ++ policy->cpuinfo.max_freq); ++ ++ return 0; ++} ++ ++/* ++ * An earlier version of opp-v1 bindings used to name the regulator ++ * "cpu0-supply", we still need to handle that for backwards compatibility. ++ */ ++static const char *find_supply_name(struct device *dev) ++{ ++ struct device_node *np; ++ struct property *pp; ++ int cpu = dev->id; ++ const char *name = NULL; ++ ++ np = of_node_get(dev->of_node); ++ ++ /* This must be valid for sure */ ++ if (WARN_ON(!np)) ++ return NULL; ++ ++ /* Try "cpu0" for older DTs */ ++ if (!cpu) { ++ pp = of_find_property(np, "cpu0-supply", NULL); ++ if (pp) { ++ name = "cpu0"; ++ goto node_put; ++ } ++ } ++ ++ pp = of_find_property(np, "cpu-supply", NULL); ++ if (pp) { ++ name = "cpu"; ++ goto node_put; ++ } ++ ++ dev_dbg(dev, "no regulator for cpu%d\n", cpu); ++node_put: ++ of_node_put(np); ++ return name; ++} ++ ++static int resources_available(void) ++{ ++ struct device *cpu_dev; ++ struct regulator *cpu_reg; ++ struct clk *cpu_clk; ++ int ret = 0; ++ const char *name; ++ ++ cpu_dev = get_cpu_device(0); ++ if (!cpu_dev) { ++ pr_err("failed to get cpu0 device\n"); ++ return -ENODEV; ++ } ++ ++ cpu_clk = clk_get(cpu_dev, NULL); ++ ret = PTR_ERR_OR_ZERO(cpu_clk); ++ if (ret) { ++ /* ++ * If cpu's clk node is present, but clock is not yet ++ * registered, we should try defering probe. ++ */ ++ if (ret == -EPROBE_DEFER) ++ dev_dbg(cpu_dev, "clock not ready, retry\n"); ++ else ++ dev_err(cpu_dev, "failed to get clock: %d\n", ret); ++ ++ return ret; ++ } ++ ++ clk_put(cpu_clk); ++ ++ name = find_supply_name(cpu_dev); ++ /* Platform doesn't require regulator */ ++ if (!name) ++ return 0; ++ ++ cpu_reg = regulator_get_optional(cpu_dev, name); ++ ret = PTR_ERR_OR_ZERO(cpu_reg); ++ if (ret) { ++ /* ++ * If cpu's regulator supply node is present, but regulator is ++ * not yet registered, we should try defering probe. ++ */ ++ if (ret == -EPROBE_DEFER) ++ dev_dbg(cpu_dev, "cpu0 regulator not ready, retry\n"); ++ else ++ dev_dbg(cpu_dev, "no regulator for cpu0: %d\n", ret); ++ ++ return ret; ++ } ++ ++ regulator_put(cpu_reg); ++ return 0; ++} ++ ++static int cpufreq_init(struct cpufreq_policy *policy) ++{ ++ struct cpufreq_frequency_table *freq_table; ++ struct opp_table *opp_table = NULL; ++ unsigned int transition_latency; ++ struct private_data *priv; ++ struct device *cpu_dev; ++ bool fallback = false; ++ struct clk *cpu_clk; ++ const char *name; ++ int ret; ++ ++ cpu_dev = get_cpu_device(policy->cpu); ++ if (!cpu_dev) { ++ pr_err("failed to get cpu%d device\n", policy->cpu); ++ return -ENODEV; ++ } ++ ++ cpu_clk = clk_get(cpu_dev, NULL); ++ if (IS_ERR(cpu_clk)) { ++ ret = PTR_ERR(cpu_clk); ++ dev_err(cpu_dev, "%s: failed to get clk: %d\n", __func__, ret); ++ return ret; ++ } ++ ++ /* Get OPP-sharing information from "operating-points-v2" bindings */ ++ ret = dev_pm_opp_of_get_sharing_cpus(cpu_dev, policy->cpus); ++ if (ret) { ++ if (ret != -ENOENT) ++ goto out_put_clk; ++ ++ /* ++ * operating-points-v2 not supported, fallback to old method of ++ * finding shared-OPPs for backward compatibility if the ++ * platform hasn't set sharing CPUs. ++ */ ++ if (dev_pm_opp_get_sharing_cpus(cpu_dev, policy->cpus)) ++ fallback = true; ++ } ++ ++ /* ++ * OPP layer will be taking care of regulators now, but it needs to know ++ * the name of the regulator first. ++ */ ++ name = find_supply_name(cpu_dev); ++ if (name) { ++ opp_table = dev_pm_opp_set_regulators(cpu_dev, &name, 1); ++ if (IS_ERR(opp_table)) { ++ ret = PTR_ERR(opp_table); ++ dev_err(cpu_dev, ++ "Failed to set regulator for cpu%d: %d\n", ++ policy->cpu, ret); ++ goto out_put_clk; ++ } ++ } ++ ++ priv = kzalloc(sizeof(*priv), GFP_KERNEL); ++ if (!priv) { ++ ret = -ENOMEM; ++ goto out_put_regulator; ++ } ++ ++ priv->reg_name = name; ++ priv->opp_table = opp_table; ++ ++ /* ++ * Initialize OPP tables for all policy->cpus. They will be shared by ++ * all CPUs which have marked their CPUs shared with OPP bindings. ++ * ++ * For platforms not using operating-points-v2 bindings, we do this ++ * before updating policy->cpus. Otherwise, we will end up creating ++ * duplicate OPPs for policy->cpus. ++ * ++ * OPPs might be populated at runtime, don't check for error here ++ */ ++ if (!dev_pm_opp_of_cpumask_add_table(policy->cpus)) ++ priv->have_static_opps = true; ++ ++ /* ++ * But we need OPP table to function so if it is not there let's ++ * give platform code chance to provide it for us. ++ */ ++ ret = dev_pm_opp_get_opp_count(cpu_dev); ++ if (ret <= 0) { ++ dev_dbg(cpu_dev, "OPP table is not ready, deferring probe\n"); ++ ret = -EPROBE_DEFER; ++ goto out_free_opp; ++ } ++ ++ if (fallback) { ++ cpumask_setall(policy->cpus); ++ ++ /* ++ * OPP tables are initialized only for policy->cpu, do it for ++ * others as well. ++ */ ++ ret = dev_pm_opp_set_sharing_cpus(cpu_dev, policy->cpus); ++ if (ret) ++ dev_err(cpu_dev, ++ "%s: failed to mark OPPs as shared: %d\n", ++ __func__, ret); ++ } ++ ++ ret = dev_pm_opp_init_cpufreq_table(cpu_dev, &freq_table); ++ if (ret) { ++ dev_err(cpu_dev, "failed to init cpufreq table: %d\n", ret); ++ goto out_free_opp; ++ } ++ ++ priv->cpu_dev = cpu_dev; ++ ++ policy->driver_data = priv; ++ policy->clk = cpu_clk; ++ policy->freq_table = freq_table; ++ ++ policy->suspend_freq = dev_pm_opp_get_suspend_opp_freq(cpu_dev) / 1000; ++ ++ transition_latency = dev_pm_opp_get_max_transition_latency(cpu_dev); ++ if (!transition_latency) ++ transition_latency = CPUFREQ_ETERNAL; ++ ++ policy->cpuinfo.transition_latency = transition_latency; ++ policy->dvfs_possible_from_any_cpu = true; ++ ++ dev_pm_opp_of_register_em(cpu_dev, policy->cpus); ++ ++ return 0; ++ ++out_free_opp: ++ if (priv->have_static_opps) ++ dev_pm_opp_of_cpumask_remove_table(policy->cpus); ++ kfree(priv); ++out_put_regulator: ++ if (name) ++ dev_pm_opp_put_regulators(opp_table); ++out_put_clk: ++ clk_put(cpu_clk); ++ ++ return ret; ++} ++ ++static int cpufreq_online(struct cpufreq_policy *policy) ++{ ++ /* We did light-weight tear down earlier, nothing to do here */ ++ return 0; ++} ++ ++static int cpufreq_offline(struct cpufreq_policy *policy) ++{ ++ /* ++ * Preserve policy->driver_data and don't free resources on light-weight ++ * tear down. ++ */ ++ return 0; ++} ++ ++static int cpufreq_exit(struct cpufreq_policy *policy) ++{ ++ struct private_data *priv = policy->driver_data; ++ ++ dev_pm_opp_free_cpufreq_table(priv->cpu_dev, &policy->freq_table); ++ if (priv->have_static_opps) ++ dev_pm_opp_of_cpumask_remove_table(policy->related_cpus); ++ if (priv->reg_name) ++ dev_pm_opp_put_regulators(priv->opp_table); ++ ++ clk_put(policy->clk); ++ kfree(priv); ++ ++ return 0; ++} ++ ++static struct cpufreq_driver krait_cpufreq_driver = { ++ .flags = CPUFREQ_STICKY | CPUFREQ_NEED_INITIAL_FREQ_CHECK | ++ CPUFREQ_IS_COOLING_DEV, ++ .verify = cpufreq_generic_frequency_table_verify, ++ .target_index = set_target, ++ .get = cpufreq_generic_get, ++ .init = cpufreq_init, ++ .exit = cpufreq_exit, ++ .online = cpufreq_online, ++ .offline = cpufreq_offline, ++ .name = "krait-cpufreq", ++ .suspend = cpufreq_generic_suspend, ++}; ++ ++struct krait_data { ++ unsigned long idle_freq; ++ bool regulator_enabled; ++}; ++ ++static int krait_cache_set_opp(struct dev_pm_set_opp_data *data) ++{ ++ unsigned long old_freq = data->old_opp.rate, freq = data->new_opp.rate; ++ struct dev_pm_opp_supply *supply = &data->new_opp.supplies[0]; ++ struct regulator *reg = data->regulators[0]; ++ struct clk *clk = data->clk; ++ struct krait_data *kdata; ++ unsigned long idle_freq; ++ int ret; ++ ++ kdata = (struct krait_data *)dev_get_drvdata(data->dev); ++ idle_freq = kdata->idle_freq; ++ ++ /* Scaling up? Scale voltage before frequency */ ++ if (freq >= old_freq) { ++ ret = regulator_set_voltage_triplet(reg, supply->u_volt_min, ++ supply->u_volt, ++ supply->u_volt_max); ++ if (ret) ++ goto exit; ++ } ++ ++ /* ++ * Set to idle bin if switching from normal to high bin ++ * or vice versa. It has been notice that a bug is triggered ++ * in cache scaling when more than one bin is scaled, to fix ++ * this we first need to transition to the base rate and then ++ * to target rate ++ */ ++ if (likely(freq != idle_freq && old_freq != idle_freq)) { ++ ret = clk_set_rate(clk, idle_freq); ++ if (ret) ++ goto exit; ++ } ++ ++ ret = clk_set_rate(clk, freq); ++ if (ret) ++ goto exit; ++ ++ /* Scaling down? Scale voltage after frequency */ ++ if (freq < old_freq) { ++ ret = regulator_set_voltage_triplet(reg, supply->u_volt_min, ++ supply->u_volt, ++ supply->u_volt_max); ++ } ++ ++ if (unlikely(!kdata->regulator_enabled)) { ++ ret = regulator_enable(reg); ++ if (ret < 0) ++ dev_warn(data->dev, "Failed to enable regulator: %d", ret); ++ else ++ kdata->regulator_enabled = true; ++ } ++ ++exit: ++ return ret; ++}; ++ ++static int krait_cache_probe(struct platform_device *pdev) ++{ ++ struct device *dev = &pdev->dev; ++ struct krait_data *data; ++ struct opp_table *table; ++ struct dev_pm_opp *opp; ++ struct device *cpu_dev; ++ int ret; ++ ++ data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL); ++ if (!data) ++ return -ENOMEM; ++ ++ table = dev_pm_opp_set_regulators(dev, (const char *[]){ "l2" }, 1); ++ if (IS_ERR(table)) { ++ ret = PTR_ERR(table); ++ if (ret != -EPROBE_DEFER) ++ dev_err(dev, "failed to set regulators %d\n", ret); ++ ++ return ret; ++ } ++ ++ ret = PTR_ERR_OR_ZERO( ++ dev_pm_opp_register_set_opp_helper(dev, krait_cache_set_opp)); ++ if (ret) ++ return ret; ++ ++ ret = dev_pm_opp_of_add_table(dev); ++ if (ret) { ++ dev_err(dev, "failed to parse L2 freq thresholds\n"); ++ return ret; ++ } ++ ++ opp = dev_pm_opp_find_freq_ceil(dev, &data->idle_freq); ++ dev_pm_opp_put(opp); ++ ++ /* ++ * Check opp-level configuration ++ * At least 2 level must be set or the cache will always be scaled ++ * the idle freq causing some performance problem ++ * ++ * In case of invalid configuration, the l2 scaling is skipped ++ */ ++ cpu_dev = get_cpu_device(0); ++ if (!cpu_dev) { ++ pr_err("failed to get cpu0 device\n"); ++ return -ENODEV; ++ } ++ ++ /* ++ * Check if we have at least opp-level 1, 0 should always be set to ++ * the idle freq ++ */ ++ opp = dev_pm_opp_find_level_exact(dev, 1); ++ if (IS_ERR(opp)) { ++ dev_err(dev, ++ "Invalid configuration found of l2 opp. Can't find opp-level 1"); ++ goto invalid_conf; ++ } ++ dev_pm_opp_put(opp); ++ ++ /* ++ * Check if we have at least opp-level 1 in the cpu opp, 0 should always ++ * be set to the idle freq ++ */ ++ opp = dev_pm_opp_find_level_exact(cpu_dev, 1); ++ if (IS_ERR(opp)) { ++ dev_err(dev, ++ "Invalid configuration found of cpu opp. Can't find opp-level 1"); ++ goto invalid_conf; ++ } ++ dev_pm_opp_put(opp); ++ ++ platform_set_drvdata(pdev, data); ++ ++ /* The l2 scaling is enabled by linking the cpufreq driver */ ++ l2_pdev = pdev; ++ ++ return 0; ++ ++invalid_conf: ++ dev_pm_opp_remove_table(dev); ++ dev_pm_opp_put_regulators(table); ++ dev_pm_opp_unregister_set_opp_helper(table); ++ ++ return -EINVAL; ++}; ++ ++static int krait_cache_remove(struct platform_device *pdev) ++{ ++ struct device *dev = &pdev->dev; ++ struct opp_table *table = dev_pm_opp_get_opp_table(dev); ++ ++ dev_pm_opp_remove_table(dev); ++ dev_pm_opp_put_regulators(table); ++ dev_pm_opp_unregister_set_opp_helper(table); ++ ++ return 0; ++}; ++ ++static const struct of_device_id krait_cache_match_table[] = { ++ { .compatible = "qcom,krait-cache" }, ++ {} ++}; ++ ++static struct platform_driver krait_cache_driver = { ++ .driver = { ++ .name = "krait-cache", ++ .of_match_table = krait_cache_match_table, ++ }, ++ .probe = krait_cache_probe, ++ .remove = krait_cache_remove, ++}; ++module_platform_driver(krait_cache_driver); ++ ++static int krait_cpufreq_probe(struct platform_device *pdev) ++{ ++ struct cpufreq_dt_platform_data *data = dev_get_platdata(&pdev->dev); ++ int ret; ++ ++ /* ++ * All per-cluster (CPUs sharing clock/voltages) initialization is done ++ * from ->init(). In probe(), we just need to make sure that clk and ++ * regulators are available. Else defer probe and retry. ++ * ++ * FIXME: Is checking this only for CPU0 sufficient ? ++ */ ++ ret = resources_available(); ++ if (ret) ++ return ret; ++ ++ if (data) { ++ if (data->have_governor_per_policy) ++ krait_cpufreq_driver.flags |= ++ CPUFREQ_HAVE_GOVERNOR_PER_POLICY; ++ ++ krait_cpufreq_driver.resume = data->resume; ++ if (data->suspend) ++ krait_cpufreq_driver.suspend = data->suspend; ++ } ++ ++ ret = cpufreq_register_driver(&krait_cpufreq_driver); ++ if (ret) ++ dev_err(&pdev->dev, "failed register driver: %d\n", ret); ++ ++ return ret; ++} ++ ++static int krait_cpufreq_remove(struct platform_device *pdev) ++{ ++ cpufreq_unregister_driver(&krait_cpufreq_driver); ++ return 0; ++} ++ ++static struct platform_driver krait_cpufreq_platdrv = { ++ .driver = { ++ .name = "krait-cpufreq", ++ }, ++ .probe = krait_cpufreq_probe, ++ .remove = krait_cpufreq_remove, ++}; ++module_platform_driver(krait_cpufreq_platdrv); ++ ++MODULE_ALIAS("platform:krait-cpufreq"); ++MODULE_AUTHOR("Ansuel Smith "); ++MODULE_DESCRIPTION("Dedicated Krait SoC cpufreq driver"); ++MODULE_LICENSE("GPL"); diff --git a/target/linux/ipq806x/patches-5.15/098-2-Documentation-cpufreq-add-qcom-krait-cpufreq-binding.patch b/target/linux/ipq806x/patches-5.15/098-2-Documentation-cpufreq-add-qcom-krait-cpufreq-binding.patch new file mode 100644 index 0000000000..316e18b790 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/098-2-Documentation-cpufreq-add-qcom-krait-cpufreq-binding.patch @@ -0,0 +1,237 @@ +From c9ecd920324a647bf1f2b47f771c8f599cc7b551 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Sat, 22 Feb 2020 18:02:17 +0100 +Subject: [PATCH 2/8] Documentation: cpufreq: add qcom,krait-cache bindings + +Document dedicated cpufreq for Krait CPUs. + +Signed-off-by: Ansuel Smith +--- + .../bindings/cpufreq/qcom-cpufreq-krait.yaml | 221 ++++++++++++++++++ + 1 file changed, 221 insertions(+) + create mode 100644 Documentation/devicetree/bindings/cpufreq/qcom-cpufreq-krait.yaml + +--- /dev/null ++++ b/Documentation/devicetree/bindings/cpufreq/qcom-cpufreq-krait.yaml +@@ -0,0 +1,221 @@ ++# SPDX-License-Identifier: GPL-2.0 ++%YAML 1.2 ++--- ++$id: http://devicetree.org/schemas/cpufreq/qcom-cpufreq-krait.yaml# ++$schema: http://devicetree.org/meta-schemas/core.yaml# ++ ++title: CPU Frequency scaling driver for Krait SoCs ++ ++maintainers: ++ - Ansuel Smith ++ ++description: | ++ The krait cpufreq driver is a dedicated frequency scaling driver ++ based on cpufreq-dt generic driver that scale L2 cache and the ++ cores. TEST ++ ++ The L2 cache is scaled based on the max clk across all cores and ++ the clock is decided based on the opp-level set in the device tree. ++ ++ Different core freq can be linked to a specific l2 freq and the driver ++ on frequency change will scale the core and the l2 clk based of the ++ linked freq. ++ ++ On Krait SoC is present a bug and on every L2 clk change the driver ++ needs to set the clk to the idle freq before changing it to the new value. ++ ++ This requires the qcom cpufreq nvmem driver to parse the different opp ++ core clk and an additional opp table for the l2 scaling. ++ ++ If the driver detect broken config (for example missing opp-level) the ++ cpufreq driver skips the l2 scaling ++ ++ Referring to this example opp-level can be used to link a range of cpu freq ++ to a specific l2 freq: ++ cpu opp freq 384000000 has opp-level 0 ++ l2 opp freq 384000000 has opp-level 0 ++ The driver will scale l2 to 384000000 ++ ++ cpu opp freq 600000000-1000000000 has opp-level 1 ++ l2 opp freq 1000000000 has opp-level 1 ++ The driver will scale l2 to 1000000000 ++ ++allOf: ++ - $ref: /schemas/cache-controller.yaml# ++ ++select: ++ properties: ++ compatible: ++ items: ++ - enum: ++ - qcom,krait-cache ++ ++ required: ++ - compatible ++ ++properties: ++ compatible: ++ items: ++ - const: qcom,krait-cache ++ - const: cache ++ ++ cache-level: ++ const: 2 ++ ++ clocks: ++ maxItems: 1 ++ ++ clock-names: ++ const: l2 ++ ++ l2-supply: true ++ ++ operating-points-v2: true ++ ++required: ++ - compatible ++ - cache-level ++ - clocks ++ - clock-names ++ - l2-supply ++ - operating-points-v2 ++ ++additionalProperties: false ++ ++examples: ++ - | ++ cpus { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ cpu0: cpu@0 { ++ compatible = "qcom,krait"; ++ enable-method = "qcom,kpss-acc-v1"; ++ device_type = "cpu"; ++ reg = <0>; ++ next-level-cache = <&L2>; ++ qcom,acc = <&acc0>; ++ qcom,saw = <&saw0>; ++ clocks = <&kraitcc 0>, <&kraitcc 4>; ++ clock-names = "cpu", "l2"; ++ clock-latency = <100000>; ++ cpu-supply = <&smb208_s2a>; ++ operating-points-v2 = <&opp_table0>; ++ voltage-tolerance = <5>; ++ cooling-min-state = <0>; ++ cooling-max-state = <10>; ++ #cooling-cells = <2>; ++ cpu-idle-states = <&CPU_SPC>; ++ }; ++ ++ /* ... */ ++ ++ }; ++ ++ opp_table0: opp_table0 { ++ compatible = "operating-points-v2-kryo-cpu"; ++ nvmem-cells = <&speedbin_efuse>; ++ ++ opp-384000000 { ++ opp-hz = /bits/ 64 <384000000>; ++ opp-microvolt-speed0-pvs0-v0 = <1000000>; ++ opp-microvolt-speed0-pvs1-v0 = <925000>; ++ opp-microvolt-speed0-pvs2-v0 = <875000>; ++ opp-microvolt-speed0-pvs3-v0 = <800000>; ++ opp-supported-hw = <0x1>; ++ clock-latency-ns = <100000>; ++ opp-level = <0>; ++ }; ++ ++ opp-600000000 { ++ opp-hz = /bits/ 64 <600000000>; ++ opp-microvolt-speed0-pvs0-v0 = <1050000>; ++ opp-microvolt-speed0-pvs1-v0 = <975000>; ++ opp-microvolt-speed0-pvs2-v0 = <925000>; ++ opp-microvolt-speed0-pvs3-v0 = <850000>; ++ opp-supported-hw = <0x1>; ++ clock-latency-ns = <100000>; ++ opp-level = <1>; ++ }; ++ ++ opp-800000000 { ++ opp-hz = /bits/ 64 <800000000>; ++ opp-microvolt-speed0-pvs0-v0 = <1100000>; ++ opp-microvolt-speed0-pvs1-v0 = <1025000>; ++ opp-microvolt-speed0-pvs2-v0 = <995000>; ++ opp-microvolt-speed0-pvs3-v0 = <900000>; ++ opp-supported-hw = <0x1>; ++ clock-latency-ns = <100000>; ++ opp-level = <1>; ++ }; ++ ++ opp-1000000000 { ++ opp-hz = /bits/ 64 <1000000000>; ++ opp-microvolt-speed0-pvs0-v0 = <1150000>; ++ opp-microvolt-speed0-pvs1-v0 = <1075000>; ++ opp-microvolt-speed0-pvs2-v0 = <1025000>; ++ opp-microvolt-speed0-pvs3-v0 = <950000>; ++ opp-supported-hw = <0x1>; ++ clock-latency-ns = <100000>; ++ opp-level = <1>; ++ }; ++ ++ opp-1200000000 { ++ opp-hz = /bits/ 64 <1200000000>; ++ opp-microvolt-speed0-pvs0-v0 = <1200000>; ++ opp-microvolt-speed0-pvs1-v0 = <1125000>; ++ opp-microvolt-speed0-pvs2-v0 = <1075000>; ++ opp-microvolt-speed0-pvs3-v0 = <1000000>; ++ opp-supported-hw = <0x1>; ++ clock-latency-ns = <100000>; ++ opp-level = <2>; ++ }; ++ ++ opp-1400000000 { ++ opp-hz = /bits/ 64 <1400000000>; ++ opp-microvolt-speed0-pvs0-v0 = <1250000>; ++ opp-microvolt-speed0-pvs1-v0 = <1175000>; ++ opp-microvolt-speed0-pvs2-v0 = <1125000>; ++ opp-microvolt-speed0-pvs3-v0 = <1050000>; ++ opp-supported-hw = <0x1>; ++ clock-latency-ns = <100000>; ++ opp-level = <2>; ++ }; ++ }; ++ ++ opp_table_l2: opp_table_l2 { ++ compatible = "operating-points-v2"; ++ ++ opp-384000000 { ++ opp-hz = /bits/ 64 <384000000>; ++ opp-microvolt = <1100000>; ++ clock-latency-ns = <100000>; ++ opp-level = <0>; ++ }; ++ opp-1000000000 { ++ opp-hz = /bits/ 64 <1000000000>; ++ opp-microvolt = <1100000>; ++ clock-latency-ns = <100000>; ++ opp-level = <1>; ++ }; ++ opp-1200000000 { ++ opp-hz = /bits/ 64 <1200000000>; ++ opp-microvolt = <1150000>; ++ clock-latency-ns = <100000>; ++ opp-level = <2>; ++ }; ++ }; ++ ++ soc { ++ L2: l2-cache { ++ compatible = "qcom,krait-cache", "cache"; ++ cache-level = <2>; ++ ++ clocks = <&kraitcc 4>; ++ clock-names = "l2"; ++ l2-supply = <&smb208_s1a>; ++ operating-points-v2 = <&opp_table_l2>; ++ }; ++ }; ++ ++... diff --git a/target/linux/ipq806x/patches-5.15/098-3-add-fab-scaling-support-with-cpufreq.patch b/target/linux/ipq806x/patches-5.15/098-3-add-fab-scaling-support-with-cpufreq.patch new file mode 100644 index 0000000000..8ce3f062cf --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/098-3-add-fab-scaling-support-with-cpufreq.patch @@ -0,0 +1,243 @@ +--- a/drivers/clk/qcom/Makefile ++++ b/drivers/clk/qcom/Makefile +@@ -15,6 +15,7 @@ clk-qcom-$(CONFIG_KRAIT_CLOCKS) += clk-k + clk-qcom-y += clk-hfpll.o + clk-qcom-y += reset.o + clk-qcom-$(CONFIG_QCOM_GDSC) += gdsc.o ++clk-qcom-y += fab_scaling.o + + # Keep alphabetically sorted by config + obj-$(CONFIG_APQ_GCC_8084) += gcc-apq8084.o +--- /dev/null ++++ b/drivers/clk/qcom/fab_scaling.c +@@ -0,0 +1,172 @@ ++/* ++ * Copyright (c) 2015, The Linux Foundation. All rights reserved. ++ * ++ * Permission to use, copy, modify, and/or distribute this software for any ++ * purpose with or without fee is hereby granted, provided that the above ++ * copyright notice and this permission notice appear in all copies. ++ * ++ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES ++ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF ++ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ++ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES ++ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ++ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF ++ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++struct qcom_fab_scaling_data { ++ u32 fab_freq_high; ++ u32 fab_freq_nominal; ++ u32 cpu_freq_threshold; ++ struct clk *apps_fab_clk; ++ struct clk *ddr_fab_clk; ++}; ++ ++static struct qcom_fab_scaling_data *drv_data; ++ ++int scale_fabrics(unsigned long max_cpu_freq) ++{ ++ struct clk *apps_fab_clk = drv_data->apps_fab_clk, ++ *ddr_fab_clk = drv_data->ddr_fab_clk; ++ unsigned long target_freq, cur_freq; ++ int ret; ++ ++ /* Skip fab scaling if the driver is not ready */ ++ if (!apps_fab_clk || !ddr_fab_clk) ++ return 0; ++ ++ if (max_cpu_freq > drv_data->cpu_freq_threshold) ++ target_freq = drv_data->fab_freq_high; ++ else ++ target_freq = drv_data->fab_freq_nominal; ++ ++ cur_freq = clk_get_rate(ddr_fab_clk); ++ ++ if (target_freq != cur_freq) { ++ ret = clk_set_rate(apps_fab_clk, target_freq); ++ if (ret) ++ return ret; ++ ret = clk_set_rate(ddr_fab_clk, target_freq); ++ if (ret) ++ return ret; ++ } ++ ++ return 0; ++} ++EXPORT_SYMBOL(scale_fabrics); ++ ++static int ipq806x_fab_scaling_probe(struct platform_device *pdev) ++{ ++ struct device_node *np = pdev->dev.of_node; ++ struct clk *apps_fab_clk, *ddr_fab_clk; ++ int ret; ++ ++ if (!np) ++ return -ENODEV; ++ ++ drv_data = kzalloc(sizeof(*drv_data), GFP_KERNEL); ++ if (!drv_data) ++ return -ENOMEM; ++ ++ if (of_property_read_u32(np, "fab_freq_high", &drv_data->fab_freq_high)) { ++ pr_err("FABRICS turbo freq not found. Using defaults...\n"); ++ drv_data->fab_freq_high = 533000000; ++ } ++ ++ if (of_property_read_u32(np, "fab_freq_nominal", &drv_data->fab_freq_nominal)) { ++ pr_err("FABRICS nominal freq not found. Using defaults...\n"); ++ drv_data->fab_freq_nominal = 400000000; ++ } ++ ++ if (of_property_read_u32(np, "cpu_freq_threshold", &drv_data->cpu_freq_threshold)) { ++ pr_err("FABRICS cpu freq threshold not found. Using defaults...\n"); ++ drv_data->cpu_freq_threshold = 1000000000; ++ } ++ ++ apps_fab_clk = devm_clk_get(&pdev->dev, "apps-fab-clk"); ++ ret = PTR_ERR_OR_ZERO(apps_fab_clk); ++ if (ret) { ++ /* ++ * If apps fab clk node is present, but clock is not yet ++ * registered, we should try defering probe. ++ */ ++ if (ret != -EPROBE_DEFER) { ++ pr_err("Failed to get APPS FABRIC clock: %d\n", ret); ++ ret = -ENODEV; ++ } ++ goto err; ++ } ++ ++ clk_prepare_enable(apps_fab_clk); ++ clk_set_rate(apps_fab_clk, drv_data->fab_freq_high); ++ drv_data->apps_fab_clk = apps_fab_clk; ++ ++ ddr_fab_clk = devm_clk_get(&pdev->dev, "ddr-fab-clk"); ++ ret = PTR_ERR_OR_ZERO(ddr_fab_clk); ++ if (ret) { ++ /* ++ * If ddr fab clk node is present, but clock is not yet ++ * registered, we should try defering probe. ++ */ ++ if (ret != -EPROBE_DEFER) { ++ pr_err("Failed to get DDR FABRIC clock: %d\n", ret); ++ ddr_fab_clk = NULL; ++ ret = -ENODEV; ++ } ++ goto err; ++ } ++ ++ clk_prepare_enable(ddr_fab_clk); ++ clk_set_rate(ddr_fab_clk, drv_data->fab_freq_high); ++ drv_data->ddr_fab_clk = ddr_fab_clk; ++ ++ return 0; ++err: ++ kfree(drv_data); ++ return ret; ++} ++ ++static int ipq806x_fab_scaling_remove(struct platform_device *pdev) ++{ ++ kfree(drv_data); ++ return 0; ++} ++ ++static const struct of_device_id fab_scaling_ipq806x_match_table[] = { ++ { .compatible = "qcom,fab-scaling" }, ++ { } ++}; ++ ++static struct platform_driver fab_scaling_ipq806x_driver = { ++ .probe = ipq806x_fab_scaling_probe, ++ .remove = ipq806x_fab_scaling_remove, ++ .driver = { ++ .name = "fab-scaling", ++ .of_match_table = fab_scaling_ipq806x_match_table, ++ }, ++}; ++ ++static int __init fab_scaling_ipq806x_init(void) ++{ ++ return platform_driver_register(&fab_scaling_ipq806x_driver); ++} ++late_initcall(fab_scaling_ipq806x_init); ++ ++static void __exit fab_scaling_ipq806x_exit(void) ++{ ++ platform_driver_unregister(&fab_scaling_ipq806x_driver); ++} ++module_exit(fab_scaling_ipq806x_exit); +--- /dev/null ++++ b/include/linux/fab_scaling.h +@@ -0,0 +1,31 @@ ++/* ++ * Copyright (c) 2015, The Linux Foundation. All rights reserved. ++ * ++ * Permission to use, copy, modify, and/or distribute this software for any ++ * purpose with or without fee is hereby granted, provided that the above ++ * copyright notice and this permission notice appear in all copies. ++ * ++ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES ++ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF ++ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ++ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES ++ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ++ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF ++ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. ++ */ ++ ++ ++#ifndef __FAB_SCALING_H ++#define __FAB_SCALING_H ++ ++/** ++ * scale_fabrics - Scale DDR and APPS FABRICS ++ * ++ * This function monitors all the registered clocks and does APPS ++ * and DDR FABRIC scaling based on the idle frequencies with which ++ * it was registered. ++ * ++ */ ++int scale_fabrics(unsigned long max_cpu_freq); ++ ++#endif +--- a/drivers/cpufreq/qcom-cpufreq-krait.c ++++ b/drivers/cpufreq/qcom-cpufreq-krait.c +@@ -15,6 +15,7 @@ + #include + #include + #include ++#include + + #include "cpufreq-dt.h" + +@@ -68,6 +69,13 @@ static int set_target(struct cpufreq_pol + return -EINVAL; + } + ++ /* ++ * Scale fabrics with max freq across all cores ++ */ ++ ret = scale_fabrics(target_freq); ++ if (ret) ++ return ret; ++ + opp = dev_pm_opp_find_level_exact(&l2_pdev->dev, level); + if (IS_ERR(opp)) { + dev_err(&l2_pdev->dev, diff --git a/target/linux/ipq806x/patches-5.15/099-1-mtd-nand-raw-qcom_nandc-add-boot_layout_mode-support.patch b/target/linux/ipq806x/patches-5.15/099-1-mtd-nand-raw-qcom_nandc-add-boot_layout_mode-support.patch new file mode 100644 index 0000000000..6106dfb8dc --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/099-1-mtd-nand-raw-qcom_nandc-add-boot_layout_mode-support.patch @@ -0,0 +1,239 @@ +From 6949d651e3be3ebbfedb6bbd5b541cfda6ee58a9 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Wed, 10 Feb 2021 10:40:17 +0100 +Subject: [PATCH 1/2] mtd: nand: raw: qcom_nandc: add boot_layout_mode support + +ipq806x nand have a special ecc configuration for the boot pages. The +use of the non-boot pages configuration on boot pages cause I/O error +and can cause broken data written to the nand. Add support for this +special configuration if the page to be read/write is in the size of the +boot pages set by the dts. + +Signed-off-by: Ansuel Smith +--- + drivers/mtd/nand/raw/qcom_nandc.c | 82 +++++++++++++++++++++++++++++-- + 1 file changed, 77 insertions(+), 5 deletions(-) + +--- a/drivers/mtd/nand/raw/qcom_nandc.c ++++ b/drivers/mtd/nand/raw/qcom_nandc.c +@@ -159,6 +159,11 @@ + /* NAND_CTRL bits */ + #define BAM_MODE_EN BIT(0) + ++ ++#define UD_SIZE_BYTES_MASK (0x3ff << UD_SIZE_BYTES) ++#define SPARE_SIZE_BYTES_MASK (0xf << SPARE_SIZE_BYTES) ++#define ECC_NUM_DATA_BYTES_MASK (0x3ff << ECC_NUM_DATA_BYTES) ++ + /* + * the NAND controller performs reads/writes with ECC in 516 byte chunks. + * the driver calls the chunks 'step' or 'codeword' interchangeably +@@ -430,6 +435,13 @@ struct qcom_nand_controller { + * @cfg0, cfg1, cfg0_raw..: NANDc register configurations needed for + * ecc/non-ecc mode for the current nand flash + * device ++ * ++ * @boot_pages_conf: keep track of the current ecc configuration used by ++ * the driver for read/write operation. (boot pages ++ * have different configuration than normal page) ++ * @boot_pages: number of pages starting from 0 used as boot pages ++ * where the driver will use the boot pages ecc ++ * configuration for read/write operation + */ + struct qcom_nand_host { + struct nand_chip chip; +@@ -452,6 +464,9 @@ struct qcom_nand_host { + u32 ecc_bch_cfg; + u32 clrflashstatus; + u32 clrreadstatus; ++ ++ bool boot_pages_conf; ++ u32 boot_pages; + }; + + /* +@@ -460,12 +475,14 @@ struct qcom_nand_host { + * @ecc_modes - ecc mode for NAND + * @is_bam - whether NAND controller is using BAM + * @is_qpic - whether NAND CTRL is part of qpic IP ++ * @has_boot_pages - whether NAND has different ecc settings for boot pages + * @dev_cmd_reg_start - NAND_DEV_CMD_* registers starting offset + */ + struct qcom_nandc_props { + u32 ecc_modes; + bool is_bam; + bool is_qpic; ++ bool has_boot_pages; + u32 dev_cmd_reg_start; + }; + +@@ -1604,7 +1621,7 @@ qcom_nandc_read_cw_raw(struct mtd_info * + data_size1 = mtd->writesize - host->cw_size * (ecc->steps - 1); + oob_size1 = host->bbm_size; + +- if (cw == (ecc->steps - 1)) { ++ if (cw == (ecc->steps - 1) && !host->boot_pages_conf) { + data_size2 = ecc->size - data_size1 - + ((ecc->steps - 1) * 4); + oob_size2 = (ecc->steps * 4) + host->ecc_bytes_hw + +@@ -1685,7 +1702,7 @@ check_for_erased_page(struct qcom_nand_h + } + + for_each_set_bit(cw, &uncorrectable_cws, ecc->steps) { +- if (cw == (ecc->steps - 1)) { ++ if (cw == (ecc->steps - 1) && !host->boot_pages_conf) { + data_size = ecc->size - ((ecc->steps - 1) * 4); + oob_size = (ecc->steps * 4) + host->ecc_bytes_hw; + } else { +@@ -1844,7 +1861,7 @@ static int read_page_ecc(struct qcom_nan + for (i = 0; i < ecc->steps; i++) { + int data_size, oob_size; + +- if (i == (ecc->steps - 1)) { ++ if (i == (ecc->steps - 1) && !host->boot_pages_conf) { + data_size = ecc->size - ((ecc->steps - 1) << 2); + oob_size = (ecc->steps << 2) + host->ecc_bytes_hw + + host->spare_bytes; +@@ -1941,6 +1958,30 @@ static int copy_last_cw(struct qcom_nand + return ret; + } + ++static void ++check_boot_pages_conf(struct qcom_nand_host *host, int page) ++{ ++ bool boot_pages_conf = page < host->boot_pages; ++ ++ /* Skip conf write if we are already in the correct mode */ ++ if (boot_pages_conf != host->boot_pages_conf) { ++ host->boot_pages_conf = boot_pages_conf; ++ ++ host->cw_data = boot_pages_conf ? 512 : 516; ++ host->spare_bytes = host->cw_size - host->ecc_bytes_hw - ++ host->bbm_size - host->cw_data; ++ ++ host->cfg0 &= ~(SPARE_SIZE_BYTES_MASK | UD_SIZE_BYTES_MASK); ++ host->cfg0 |= host->spare_bytes << SPARE_SIZE_BYTES | ++ host->cw_data << UD_SIZE_BYTES; ++ ++ host->ecc_bch_cfg &= ~ECC_NUM_DATA_BYTES_MASK; ++ host->ecc_bch_cfg |= host->cw_data << ECC_NUM_DATA_BYTES; ++ host->ecc_buf_cfg = (boot_pages_conf ? 0x1ff : 0x203) << ++ NUM_STEPS; ++ } ++} ++ + /* implements ecc->read_page() */ + static int qcom_nandc_read_page(struct nand_chip *chip, uint8_t *buf, + int oob_required, int page) +@@ -1949,6 +1990,9 @@ static int qcom_nandc_read_page(struct n + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + u8 *data_buf, *oob_buf = NULL; + ++ if (host->boot_pages) ++ check_boot_pages_conf(host, page); ++ + nand_read_page_op(chip, page, 0, NULL, 0); + data_buf = buf; + oob_buf = oob_required ? chip->oob_poi : NULL; +@@ -1968,6 +2012,9 @@ static int qcom_nandc_read_page_raw(stru + int cw, ret; + u8 *data_buf = buf, *oob_buf = chip->oob_poi; + ++ if (host->boot_pages) ++ check_boot_pages_conf(host, page); ++ + for (cw = 0; cw < ecc->steps; cw++) { + ret = qcom_nandc_read_cw_raw(mtd, chip, data_buf, oob_buf, + page, cw); +@@ -1988,6 +2035,9 @@ static int qcom_nandc_read_oob(struct na + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + struct nand_ecc_ctrl *ecc = &chip->ecc; + ++ if (host->boot_pages) ++ check_boot_pages_conf(host, page); ++ + clear_read_regs(nandc); + clear_bam_transaction(nandc); + +@@ -2008,6 +2058,9 @@ static int qcom_nandc_write_page(struct + u8 *data_buf, *oob_buf; + int i, ret; + ++ if (host->boot_pages) ++ check_boot_pages_conf(host, page); ++ + nand_prog_page_begin_op(chip, page, 0, NULL, 0); + + clear_read_regs(nandc); +@@ -2023,7 +2076,7 @@ static int qcom_nandc_write_page(struct + for (i = 0; i < ecc->steps; i++) { + int data_size, oob_size; + +- if (i == (ecc->steps - 1)) { ++ if (i == (ecc->steps - 1) && !host->boot_pages_conf) { + data_size = ecc->size - ((ecc->steps - 1) << 2); + oob_size = (ecc->steps << 2) + host->ecc_bytes_hw + + host->spare_bytes; +@@ -2080,6 +2133,9 @@ static int qcom_nandc_write_page_raw(str + u8 *data_buf, *oob_buf; + int i, ret; + ++ if (host->boot_pages) ++ check_boot_pages_conf(host, page); ++ + nand_prog_page_begin_op(chip, page, 0, NULL, 0); + clear_read_regs(nandc); + clear_bam_transaction(nandc); +@@ -2098,7 +2154,7 @@ static int qcom_nandc_write_page_raw(str + data_size1 = mtd->writesize - host->cw_size * (ecc->steps - 1); + oob_size1 = host->bbm_size; + +- if (i == (ecc->steps - 1)) { ++ if (i == (ecc->steps - 1) && !host->boot_pages_conf) { + data_size2 = ecc->size - data_size1 - + ((ecc->steps - 1) << 2); + oob_size2 = (ecc->steps << 2) + host->ecc_bytes_hw + +@@ -2158,6 +2214,9 @@ static int qcom_nandc_write_oob(struct n + int data_size, oob_size; + int ret; + ++ if (host->boot_pages) ++ check_boot_pages_conf(host, page); ++ + host->use_ecc = true; + clear_bam_transaction(nandc); + +@@ -2806,6 +2865,7 @@ static int qcom_nand_host_init_and_regis + struct nand_chip *chip = &host->chip; + struct mtd_info *mtd = nand_to_mtd(chip); + struct device *dev = nandc->dev; ++ u32 boot_pages_size; + int ret; + + ret = of_property_read_u32(dn, "reg", &host->cs); +@@ -2866,6 +2926,17 @@ static int qcom_nand_host_init_and_regis + if (ret) + nand_cleanup(chip); + ++ if (nandc->props->has_boot_pages && ++ of_property_read_bool(dn, "nand-is-boot-medium")) { ++ ret = of_property_read_u32(dn, "qcom,boot_pages_size", ++ &boot_pages_size); ++ if (ret) ++ dev_warn(dev, "can't get boot pages size"); ++ else ++ /* Convert size to nand pages */ ++ host->boot_pages = boot_pages_size / mtd->writesize; ++ } ++ + return ret; + } + +@@ -3032,6 +3103,7 @@ static int qcom_nandc_remove(struct plat + static const struct qcom_nandc_props ipq806x_nandc_props = { + .ecc_modes = (ECC_RS_4BIT | ECC_BCH_8BIT), + .is_bam = false, ++ .has_boot_pages = true, + .dev_cmd_reg_start = 0x0, + }; + diff --git a/target/linux/ipq806x/patches-5.15/099-2-Documentation-devicetree-mtd-qcom_nandc-document-qco.patch b/target/linux/ipq806x/patches-5.15/099-2-Documentation-devicetree-mtd-qcom_nandc-document-qco.patch new file mode 100644 index 0000000000..79036cb057 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/099-2-Documentation-devicetree-mtd-qcom_nandc-document-qco.patch @@ -0,0 +1,42 @@ +From 6fb003a7a117f97a35b078ba726c84adeae29c4c Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Wed, 10 Feb 2021 10:54:19 +0100 +Subject: [PATCH 2/2] Documentation: devicetree: mtd: qcom_nandc: document + qcom,boot_layout_size binding + +Document new qcom,boot_layout_size binding used to apply special +read/write confituation to boots partitions. + +Signed-off-by: Ansuel Smith +--- + Documentation/devicetree/bindings/mtd/qcom_nandc.txt | 11 +++++++++++ + 1 file changed, 11 insertions(+) + +--- a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt ++++ b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt +@@ -52,6 +52,15 @@ Optional properties: + be used according to chip requirement and available + OOB size. + ++EBI2 specific properties: ++- nand-is-boot-medium: nand contains boot partitions and different ecc configuration ++ should be used for these partitions. ++- qcom,boot_pages_size: should contain the size of the total boot partitions ++ where the boot layout read/write specific configuration ++ should be used. The boot layout is considered from the ++ start of the nand to the value set in this binding. ++ Only used in combination with 'nand-is-boot-medium'. ++ + Each nandcs device node may optionally contain a 'partitions' sub-node, which + further contains sub-nodes describing the flash partition mapping. See + partition.txt for more detail. +@@ -80,6 +89,9 @@ nand-controller@1ac00000 { + nand-ecc-strength = <4>; + nand-bus-width = <8>; + ++ nand-is-boot-medium; ++ qcom,boot_pages_size: <0x58a0000>; ++ + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; diff --git a/target/linux/ipq806x/patches-5.15/100-v5.11-dmaengine-qcom-add_ADM_driver.patch b/target/linux/ipq806x/patches-5.15/100-v5.11-dmaengine-qcom-add_ADM_driver.patch new file mode 100644 index 0000000000..2d24da01e4 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/100-v5.11-dmaengine-qcom-add_ADM_driver.patch @@ -0,0 +1,965 @@ +From 5c9f8c2dbdbe53818bcde6aa6695e1331e5f841f Mon Sep 17 00:00:00 2001 +From: Jonathan McDowell +Date: Sat, 14 Nov 2020 14:02:33 +0000 +Subject: dmaengine: qcom: Add ADM driver + +Add the DMA engine driver for the QCOM Application Data Mover (ADM) DMA +controller found in the MSM8x60 and IPQ/APQ8064 platforms. + +The ADM supports both memory to memory transactions and memory +to/from peripheral device transactions. The controller also provides +flow control capabilities for transactions to/from peripheral devices. + +The initial release of this driver supports slave transfers to/from +peripherals and also incorporates CRCI (client rate control interface) +flow control. + +The hardware only supports a 32 bit physical address, so specifying +!PHYS_ADDR_T_64BIT gives maximum COMPILE_TEST coverage without having to +spend effort on kludging things in the code that will never actually be +needed on real hardware. + +Signed-off-by: Andy Gross +Signed-off-by: Thomas Pedersen +Signed-off-by: Jonathan McDowell +Link: https://lore.kernel.org/r/20201114140233.GM32650@earth.li +Signed-off-by: Vinod Koul +--- + drivers/dma/qcom/Kconfig | 11 + + drivers/dma/qcom/Makefile | 1 + + drivers/dma/qcom/qcom_adm.c | 903 ++++++++++++++++++++++++++++++++++++++++++++ + 3 files changed, 915 insertions(+) + create mode 100644 drivers/dma/qcom/qcom_adm.c + +--- a/drivers/dma/qcom/Kconfig ++++ b/drivers/dma/qcom/Kconfig +@@ -1,4 +1,15 @@ + # SPDX-License-Identifier: GPL-2.0-only ++config QCOM_ADM ++ tristate "Qualcomm ADM support" ++ depends on (ARCH_QCOM || COMPILE_TEST) && !PHYS_ADDR_T_64BIT ++ select DMA_ENGINE ++ select DMA_VIRTUAL_CHANNELS ++ help ++ Enable support for the Qualcomm Application Data Mover (ADM) DMA ++ controller, as present on MSM8x60, APQ8064, and IPQ8064 devices. ++ This controller provides DMA capabilities for both general purpose ++ and on-chip peripheral devices. ++ + config QCOM_BAM_DMA + tristate "QCOM BAM DMA support" + depends on ARCH_QCOM || (COMPILE_TEST && OF && ARM) +--- a/drivers/dma/qcom/Makefile ++++ b/drivers/dma/qcom/Makefile +@@ -1,4 +1,5 @@ + # SPDX-License-Identifier: GPL-2.0 ++obj-$(CONFIG_QCOM_ADM) += qcom_adm.o + obj-$(CONFIG_QCOM_BAM_DMA) += bam_dma.o + obj-$(CONFIG_QCOM_HIDMA_MGMT) += hdma_mgmt.o + hdma_mgmt-objs := hidma_mgmt.o hidma_mgmt_sys.o +--- /dev/null ++++ b/drivers/dma/qcom/qcom_adm.c +@@ -0,0 +1,903 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++/* ++ * Copyright (c) 2013-2015, The Linux Foundation. All rights reserved. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include "../dmaengine.h" ++#include "../virt-dma.h" ++ ++/* ADM registers - calculated from channel number and security domain */ ++#define ADM_CHAN_MULTI 0x4 ++#define ADM_CI_MULTI 0x4 ++#define ADM_CRCI_MULTI 0x4 ++#define ADM_EE_MULTI 0x800 ++#define ADM_CHAN_OFFS(chan) (ADM_CHAN_MULTI * (chan)) ++#define ADM_EE_OFFS(ee) (ADM_EE_MULTI * (ee)) ++#define ADM_CHAN_EE_OFFS(chan, ee) (ADM_CHAN_OFFS(chan) + ADM_EE_OFFS(ee)) ++#define ADM_CHAN_OFFS(chan) (ADM_CHAN_MULTI * (chan)) ++#define ADM_CI_OFFS(ci) (ADM_CHAN_OFF(ci)) ++#define ADM_CH_CMD_PTR(chan, ee) (ADM_CHAN_EE_OFFS(chan, ee)) ++#define ADM_CH_RSLT(chan, ee) (0x40 + ADM_CHAN_EE_OFFS(chan, ee)) ++#define ADM_CH_FLUSH_STATE0(chan, ee) (0x80 + ADM_CHAN_EE_OFFS(chan, ee)) ++#define ADM_CH_STATUS_SD(chan, ee) (0x200 + ADM_CHAN_EE_OFFS(chan, ee)) ++#define ADM_CH_CONF(chan) (0x240 + ADM_CHAN_OFFS(chan)) ++#define ADM_CH_RSLT_CONF(chan, ee) (0x300 + ADM_CHAN_EE_OFFS(chan, ee)) ++#define ADM_SEC_DOMAIN_IRQ_STATUS(ee) (0x380 + ADM_EE_OFFS(ee)) ++#define ADM_CI_CONF(ci) (0x390 + (ci) * ADM_CI_MULTI) ++#define ADM_GP_CTL 0x3d8 ++#define ADM_CRCI_CTL(crci, ee) (0x400 + (crci) * ADM_CRCI_MULTI + \ ++ ADM_EE_OFFS(ee)) ++ ++/* channel status */ ++#define ADM_CH_STATUS_VALID BIT(1) ++ ++/* channel result */ ++#define ADM_CH_RSLT_VALID BIT(31) ++#define ADM_CH_RSLT_ERR BIT(3) ++#define ADM_CH_RSLT_FLUSH BIT(2) ++#define ADM_CH_RSLT_TPD BIT(1) ++ ++/* channel conf */ ++#define ADM_CH_CONF_SHADOW_EN BIT(12) ++#define ADM_CH_CONF_MPU_DISABLE BIT(11) ++#define ADM_CH_CONF_PERM_MPU_CONF BIT(9) ++#define ADM_CH_CONF_FORCE_RSLT_EN BIT(7) ++#define ADM_CH_CONF_SEC_DOMAIN(ee) ((((ee) & 0x3) << 4) | (((ee) & 0x4) << 11)) ++ ++/* channel result conf */ ++#define ADM_CH_RSLT_CONF_FLUSH_EN BIT(1) ++#define ADM_CH_RSLT_CONF_IRQ_EN BIT(0) ++ ++/* CRCI CTL */ ++#define ADM_CRCI_CTL_MUX_SEL BIT(18) ++#define ADM_CRCI_CTL_RST BIT(17) ++ ++/* CI configuration */ ++#define ADM_CI_RANGE_END(x) ((x) << 24) ++#define ADM_CI_RANGE_START(x) ((x) << 16) ++#define ADM_CI_BURST_4_WORDS BIT(2) ++#define ADM_CI_BURST_8_WORDS BIT(3) ++ ++/* GP CTL */ ++#define ADM_GP_CTL_LP_EN BIT(12) ++#define ADM_GP_CTL_LP_CNT(x) ((x) << 8) ++ ++/* Command pointer list entry */ ++#define ADM_CPLE_LP BIT(31) ++#define ADM_CPLE_CMD_PTR_LIST BIT(29) ++ ++/* Command list entry */ ++#define ADM_CMD_LC BIT(31) ++#define ADM_CMD_DST_CRCI(n) (((n) & 0xf) << 7) ++#define ADM_CMD_SRC_CRCI(n) (((n) & 0xf) << 3) ++ ++#define ADM_CMD_TYPE_SINGLE 0x0 ++#define ADM_CMD_TYPE_BOX 0x3 ++ ++#define ADM_CRCI_MUX_SEL BIT(4) ++#define ADM_DESC_ALIGN 8 ++#define ADM_MAX_XFER (SZ_64K - 1) ++#define ADM_MAX_ROWS (SZ_64K - 1) ++#define ADM_MAX_CHANNELS 16 ++ ++struct adm_desc_hw_box { ++ u32 cmd; ++ u32 src_addr; ++ u32 dst_addr; ++ u32 row_len; ++ u32 num_rows; ++ u32 row_offset; ++}; ++ ++struct adm_desc_hw_single { ++ u32 cmd; ++ u32 src_addr; ++ u32 dst_addr; ++ u32 len; ++}; ++ ++struct adm_async_desc { ++ struct virt_dma_desc vd; ++ struct adm_device *adev; ++ ++ size_t length; ++ enum dma_transfer_direction dir; ++ dma_addr_t dma_addr; ++ size_t dma_len; ++ ++ void *cpl; ++ dma_addr_t cp_addr; ++ u32 crci; ++ u32 mux; ++ u32 blk_size; ++}; ++ ++struct adm_chan { ++ struct virt_dma_chan vc; ++ struct adm_device *adev; ++ ++ /* parsed from DT */ ++ u32 id; /* channel id */ ++ ++ struct adm_async_desc *curr_txd; ++ struct dma_slave_config slave; ++ struct list_head node; ++ ++ int error; ++ int initialized; ++}; ++ ++static inline struct adm_chan *to_adm_chan(struct dma_chan *common) ++{ ++ return container_of(common, struct adm_chan, vc.chan); ++} ++ ++struct adm_device { ++ void __iomem *regs; ++ struct device *dev; ++ struct dma_device common; ++ struct device_dma_parameters dma_parms; ++ struct adm_chan *channels; ++ ++ u32 ee; ++ ++ struct clk *core_clk; ++ struct clk *iface_clk; ++ ++ struct reset_control *clk_reset; ++ struct reset_control *c0_reset; ++ struct reset_control *c1_reset; ++ struct reset_control *c2_reset; ++ int irq; ++}; ++ ++/** ++ * adm_free_chan - Frees dma resources associated with the specific channel ++ * ++ * Free all allocated descriptors associated with this channel ++ * ++ */ ++static void adm_free_chan(struct dma_chan *chan) ++{ ++ /* free all queued descriptors */ ++ vchan_free_chan_resources(to_virt_chan(chan)); ++} ++ ++/** ++ * adm_get_blksize - Get block size from burst value ++ * ++ */ ++static int adm_get_blksize(unsigned int burst) ++{ ++ int ret; ++ ++ switch (burst) { ++ case 16: ++ case 32: ++ case 64: ++ case 128: ++ ret = ffs(burst >> 4) - 1; ++ break; ++ case 192: ++ ret = 4; ++ break; ++ case 256: ++ ret = 5; ++ break; ++ default: ++ ret = -EINVAL; ++ break; ++ } ++ ++ return ret; ++} ++ ++/** ++ * adm_process_fc_descriptors - Process descriptors for flow controlled xfers ++ * ++ * @achan: ADM channel ++ * @desc: Descriptor memory pointer ++ * @sg: Scatterlist entry ++ * @crci: CRCI value ++ * @burst: Burst size of transaction ++ * @direction: DMA transfer direction ++ */ ++static void *adm_process_fc_descriptors(struct adm_chan *achan, void *desc, ++ struct scatterlist *sg, u32 crci, ++ u32 burst, ++ enum dma_transfer_direction direction) ++{ ++ struct adm_desc_hw_box *box_desc = NULL; ++ struct adm_desc_hw_single *single_desc; ++ u32 remainder = sg_dma_len(sg); ++ u32 rows, row_offset, crci_cmd; ++ u32 mem_addr = sg_dma_address(sg); ++ u32 *incr_addr = &mem_addr; ++ u32 *src, *dst; ++ ++ if (direction == DMA_DEV_TO_MEM) { ++ crci_cmd = ADM_CMD_SRC_CRCI(crci); ++ row_offset = burst; ++ src = &achan->slave.src_addr; ++ dst = &mem_addr; ++ } else { ++ crci_cmd = ADM_CMD_DST_CRCI(crci); ++ row_offset = burst << 16; ++ src = &mem_addr; ++ dst = &achan->slave.dst_addr; ++ } ++ ++ while (remainder >= burst) { ++ box_desc = desc; ++ box_desc->cmd = ADM_CMD_TYPE_BOX | crci_cmd; ++ box_desc->row_offset = row_offset; ++ box_desc->src_addr = *src; ++ box_desc->dst_addr = *dst; ++ ++ rows = remainder / burst; ++ rows = min_t(u32, rows, ADM_MAX_ROWS); ++ box_desc->num_rows = rows << 16 | rows; ++ box_desc->row_len = burst << 16 | burst; ++ ++ *incr_addr += burst * rows; ++ remainder -= burst * rows; ++ desc += sizeof(*box_desc); ++ } ++ ++ /* if leftover bytes, do one single descriptor */ ++ if (remainder) { ++ single_desc = desc; ++ single_desc->cmd = ADM_CMD_TYPE_SINGLE | crci_cmd; ++ single_desc->len = remainder; ++ single_desc->src_addr = *src; ++ single_desc->dst_addr = *dst; ++ desc += sizeof(*single_desc); ++ ++ if (sg_is_last(sg)) ++ single_desc->cmd |= ADM_CMD_LC; ++ } else { ++ if (box_desc && sg_is_last(sg)) ++ box_desc->cmd |= ADM_CMD_LC; ++ } ++ ++ return desc; ++} ++ ++/** ++ * adm_process_non_fc_descriptors - Process descriptors for non-fc xfers ++ * ++ * @achan: ADM channel ++ * @desc: Descriptor memory pointer ++ * @sg: Scatterlist entry ++ * @direction: DMA transfer direction ++ */ ++static void *adm_process_non_fc_descriptors(struct adm_chan *achan, void *desc, ++ struct scatterlist *sg, ++ enum dma_transfer_direction direction) ++{ ++ struct adm_desc_hw_single *single_desc; ++ u32 remainder = sg_dma_len(sg); ++ u32 mem_addr = sg_dma_address(sg); ++ u32 *incr_addr = &mem_addr; ++ u32 *src, *dst; ++ ++ if (direction == DMA_DEV_TO_MEM) { ++ src = &achan->slave.src_addr; ++ dst = &mem_addr; ++ } else { ++ src = &mem_addr; ++ dst = &achan->slave.dst_addr; ++ } ++ ++ do { ++ single_desc = desc; ++ single_desc->cmd = ADM_CMD_TYPE_SINGLE; ++ single_desc->src_addr = *src; ++ single_desc->dst_addr = *dst; ++ single_desc->len = (remainder > ADM_MAX_XFER) ? ++ ADM_MAX_XFER : remainder; ++ ++ remainder -= single_desc->len; ++ *incr_addr += single_desc->len; ++ desc += sizeof(*single_desc); ++ } while (remainder); ++ ++ /* set last command if this is the end of the whole transaction */ ++ if (sg_is_last(sg)) ++ single_desc->cmd |= ADM_CMD_LC; ++ ++ return desc; ++} ++ ++/** ++ * adm_prep_slave_sg - Prep slave sg transaction ++ * ++ * @chan: dma channel ++ * @sgl: scatter gather list ++ * @sg_len: length of sg ++ * @direction: DMA transfer direction ++ * @flags: DMA flags ++ * @context: transfer context (unused) ++ */ ++static struct dma_async_tx_descriptor *adm_prep_slave_sg(struct dma_chan *chan, ++ struct scatterlist *sgl, ++ unsigned int sg_len, ++ enum dma_transfer_direction direction, ++ unsigned long flags, ++ void *context) ++{ ++ struct adm_chan *achan = to_adm_chan(chan); ++ struct adm_device *adev = achan->adev; ++ struct adm_async_desc *async_desc; ++ struct scatterlist *sg; ++ dma_addr_t cple_addr; ++ u32 i, burst; ++ u32 single_count = 0, box_count = 0, crci = 0; ++ void *desc; ++ u32 *cple; ++ int blk_size = 0; ++ ++ if (!is_slave_direction(direction)) { ++ dev_err(adev->dev, "invalid dma direction\n"); ++ return NULL; ++ } ++ ++ /* ++ * get burst value from slave configuration ++ */ ++ burst = (direction == DMA_MEM_TO_DEV) ? ++ achan->slave.dst_maxburst : ++ achan->slave.src_maxburst; ++ ++ /* if using flow control, validate burst and crci values */ ++ if (achan->slave.device_fc) { ++ blk_size = adm_get_blksize(burst); ++ if (blk_size < 0) { ++ dev_err(adev->dev, "invalid burst value: %d\n", ++ burst); ++ return ERR_PTR(-EINVAL); ++ } ++ ++ crci = achan->slave.slave_id & 0xf; ++ if (!crci || achan->slave.slave_id > 0x1f) { ++ dev_err(adev->dev, "invalid crci value\n"); ++ return ERR_PTR(-EINVAL); ++ } ++ } ++ ++ /* iterate through sgs and compute allocation size of structures */ ++ for_each_sg(sgl, sg, sg_len, i) { ++ if (achan->slave.device_fc) { ++ box_count += DIV_ROUND_UP(sg_dma_len(sg) / burst, ++ ADM_MAX_ROWS); ++ if (sg_dma_len(sg) % burst) ++ single_count++; ++ } else { ++ single_count += DIV_ROUND_UP(sg_dma_len(sg), ++ ADM_MAX_XFER); ++ } ++ } ++ ++ async_desc = kzalloc(sizeof(*async_desc), GFP_NOWAIT); ++ if (!async_desc) ++ return ERR_PTR(-ENOMEM); ++ ++ if (crci) ++ async_desc->mux = achan->slave.slave_id & ADM_CRCI_MUX_SEL ? ++ ADM_CRCI_CTL_MUX_SEL : 0; ++ async_desc->crci = crci; ++ async_desc->blk_size = blk_size; ++ async_desc->dma_len = single_count * sizeof(struct adm_desc_hw_single) + ++ box_count * sizeof(struct adm_desc_hw_box) + ++ sizeof(*cple) + 2 * ADM_DESC_ALIGN; ++ ++ async_desc->cpl = kzalloc(async_desc->dma_len, GFP_NOWAIT); ++ if (!async_desc->cpl) ++ goto free; ++ ++ async_desc->adev = adev; ++ ++ /* both command list entry and descriptors must be 8 byte aligned */ ++ cple = PTR_ALIGN(async_desc->cpl, ADM_DESC_ALIGN); ++ desc = PTR_ALIGN(cple + 1, ADM_DESC_ALIGN); ++ ++ for_each_sg(sgl, sg, sg_len, i) { ++ async_desc->length += sg_dma_len(sg); ++ ++ if (achan->slave.device_fc) ++ desc = adm_process_fc_descriptors(achan, desc, sg, crci, ++ burst, direction); ++ else ++ desc = adm_process_non_fc_descriptors(achan, desc, sg, ++ direction); ++ } ++ ++ async_desc->dma_addr = dma_map_single(adev->dev, async_desc->cpl, ++ async_desc->dma_len, ++ DMA_TO_DEVICE); ++ if (dma_mapping_error(adev->dev, async_desc->dma_addr)) ++ goto free; ++ ++ cple_addr = async_desc->dma_addr + ((void *)cple - async_desc->cpl); ++ ++ /* init cmd list */ ++ dma_sync_single_for_cpu(adev->dev, cple_addr, sizeof(*cple), ++ DMA_TO_DEVICE); ++ *cple = ADM_CPLE_LP; ++ *cple |= (async_desc->dma_addr + ADM_DESC_ALIGN) >> 3; ++ dma_sync_single_for_device(adev->dev, cple_addr, sizeof(*cple), ++ DMA_TO_DEVICE); ++ ++ return vchan_tx_prep(&achan->vc, &async_desc->vd, flags); ++ ++free: ++ kfree(async_desc); ++ return ERR_PTR(-ENOMEM); ++} ++ ++/** ++ * adm_terminate_all - terminate all transactions on a channel ++ * @achan: adm dma channel ++ * ++ * Dequeues and frees all transactions, aborts current transaction ++ * No callbacks are done ++ * ++ */ ++static int adm_terminate_all(struct dma_chan *chan) ++{ ++ struct adm_chan *achan = to_adm_chan(chan); ++ struct adm_device *adev = achan->adev; ++ unsigned long flags; ++ LIST_HEAD(head); ++ ++ spin_lock_irqsave(&achan->vc.lock, flags); ++ vchan_get_all_descriptors(&achan->vc, &head); ++ ++ /* send flush command to terminate current transaction */ ++ writel_relaxed(0x0, ++ adev->regs + ADM_CH_FLUSH_STATE0(achan->id, adev->ee)); ++ ++ spin_unlock_irqrestore(&achan->vc.lock, flags); ++ ++ vchan_dma_desc_free_list(&achan->vc, &head); ++ ++ return 0; ++} ++ ++static int adm_slave_config(struct dma_chan *chan, struct dma_slave_config *cfg) ++{ ++ struct adm_chan *achan = to_adm_chan(chan); ++ unsigned long flag; ++ ++ spin_lock_irqsave(&achan->vc.lock, flag); ++ memcpy(&achan->slave, cfg, sizeof(struct dma_slave_config)); ++ spin_unlock_irqrestore(&achan->vc.lock, flag); ++ ++ return 0; ++} ++ ++/** ++ * adm_start_dma - start next transaction ++ * @achan - ADM dma channel ++ */ ++static void adm_start_dma(struct adm_chan *achan) ++{ ++ struct virt_dma_desc *vd = vchan_next_desc(&achan->vc); ++ struct adm_device *adev = achan->adev; ++ struct adm_async_desc *async_desc; ++ ++ lockdep_assert_held(&achan->vc.lock); ++ ++ if (!vd) ++ return; ++ ++ list_del(&vd->node); ++ ++ /* write next command list out to the CMD FIFO */ ++ async_desc = container_of(vd, struct adm_async_desc, vd); ++ achan->curr_txd = async_desc; ++ ++ /* reset channel error */ ++ achan->error = 0; ++ ++ if (!achan->initialized) { ++ /* enable interrupts */ ++ writel(ADM_CH_CONF_SHADOW_EN | ++ ADM_CH_CONF_PERM_MPU_CONF | ++ ADM_CH_CONF_MPU_DISABLE | ++ ADM_CH_CONF_SEC_DOMAIN(adev->ee), ++ adev->regs + ADM_CH_CONF(achan->id)); ++ ++ writel(ADM_CH_RSLT_CONF_IRQ_EN | ADM_CH_RSLT_CONF_FLUSH_EN, ++ adev->regs + ADM_CH_RSLT_CONF(achan->id, adev->ee)); ++ ++ achan->initialized = 1; ++ } ++ ++ /* set the crci block size if this transaction requires CRCI */ ++ if (async_desc->crci) { ++ writel(async_desc->mux | async_desc->blk_size, ++ adev->regs + ADM_CRCI_CTL(async_desc->crci, adev->ee)); ++ } ++ ++ /* make sure IRQ enable doesn't get reordered */ ++ wmb(); ++ ++ /* write next command list out to the CMD FIFO */ ++ writel(ALIGN(async_desc->dma_addr, ADM_DESC_ALIGN) >> 3, ++ adev->regs + ADM_CH_CMD_PTR(achan->id, adev->ee)); ++} ++ ++/** ++ * adm_dma_irq - irq handler for ADM controller ++ * @irq: IRQ of interrupt ++ * @data: callback data ++ * ++ * IRQ handler for the bam controller ++ */ ++static irqreturn_t adm_dma_irq(int irq, void *data) ++{ ++ struct adm_device *adev = data; ++ u32 srcs, i; ++ struct adm_async_desc *async_desc; ++ unsigned long flags; ++ ++ srcs = readl_relaxed(adev->regs + ++ ADM_SEC_DOMAIN_IRQ_STATUS(adev->ee)); ++ ++ for (i = 0; i < ADM_MAX_CHANNELS; i++) { ++ struct adm_chan *achan = &adev->channels[i]; ++ u32 status, result; ++ ++ if (srcs & BIT(i)) { ++ status = readl_relaxed(adev->regs + ++ ADM_CH_STATUS_SD(i, adev->ee)); ++ ++ /* if no result present, skip */ ++ if (!(status & ADM_CH_STATUS_VALID)) ++ continue; ++ ++ result = readl_relaxed(adev->regs + ++ ADM_CH_RSLT(i, adev->ee)); ++ ++ /* no valid results, skip */ ++ if (!(result & ADM_CH_RSLT_VALID)) ++ continue; ++ ++ /* flag error if transaction was flushed or failed */ ++ if (result & (ADM_CH_RSLT_ERR | ADM_CH_RSLT_FLUSH)) ++ achan->error = 1; ++ ++ spin_lock_irqsave(&achan->vc.lock, flags); ++ async_desc = achan->curr_txd; ++ ++ achan->curr_txd = NULL; ++ ++ if (async_desc) { ++ vchan_cookie_complete(&async_desc->vd); ++ ++ /* kick off next DMA */ ++ adm_start_dma(achan); ++ } ++ ++ spin_unlock_irqrestore(&achan->vc.lock, flags); ++ } ++ } ++ ++ return IRQ_HANDLED; ++} ++ ++/** ++ * adm_tx_status - returns status of transaction ++ * @chan: dma channel ++ * @cookie: transaction cookie ++ * @txstate: DMA transaction state ++ * ++ * Return status of dma transaction ++ */ ++static enum dma_status adm_tx_status(struct dma_chan *chan, dma_cookie_t cookie, ++ struct dma_tx_state *txstate) ++{ ++ struct adm_chan *achan = to_adm_chan(chan); ++ struct virt_dma_desc *vd; ++ enum dma_status ret; ++ unsigned long flags; ++ size_t residue = 0; ++ ++ ret = dma_cookie_status(chan, cookie, txstate); ++ if (ret == DMA_COMPLETE || !txstate) ++ return ret; ++ ++ spin_lock_irqsave(&achan->vc.lock, flags); ++ ++ vd = vchan_find_desc(&achan->vc, cookie); ++ if (vd) ++ residue = container_of(vd, struct adm_async_desc, vd)->length; ++ ++ spin_unlock_irqrestore(&achan->vc.lock, flags); ++ ++ /* ++ * residue is either the full length if it is in the issued list, or 0 ++ * if it is in progress. We have no reliable way of determining ++ * anything inbetween ++ */ ++ dma_set_residue(txstate, residue); ++ ++ if (achan->error) ++ return DMA_ERROR; ++ ++ return ret; ++} ++ ++/** ++ * adm_issue_pending - starts pending transactions ++ * @chan: dma channel ++ * ++ * Issues all pending transactions and starts DMA ++ */ ++static void adm_issue_pending(struct dma_chan *chan) ++{ ++ struct adm_chan *achan = to_adm_chan(chan); ++ unsigned long flags; ++ ++ spin_lock_irqsave(&achan->vc.lock, flags); ++ ++ if (vchan_issue_pending(&achan->vc) && !achan->curr_txd) ++ adm_start_dma(achan); ++ spin_unlock_irqrestore(&achan->vc.lock, flags); ++} ++ ++/** ++ * adm_dma_free_desc - free descriptor memory ++ * @vd: virtual descriptor ++ * ++ */ ++static void adm_dma_free_desc(struct virt_dma_desc *vd) ++{ ++ struct adm_async_desc *async_desc = container_of(vd, ++ struct adm_async_desc, vd); ++ ++ dma_unmap_single(async_desc->adev->dev, async_desc->dma_addr, ++ async_desc->dma_len, DMA_TO_DEVICE); ++ kfree(async_desc->cpl); ++ kfree(async_desc); ++} ++ ++static void adm_channel_init(struct adm_device *adev, struct adm_chan *achan, ++ u32 index) ++{ ++ achan->id = index; ++ achan->adev = adev; ++ ++ vchan_init(&achan->vc, &adev->common); ++ achan->vc.desc_free = adm_dma_free_desc; ++} ++ ++static int adm_dma_probe(struct platform_device *pdev) ++{ ++ struct adm_device *adev; ++ int ret; ++ u32 i; ++ ++ adev = devm_kzalloc(&pdev->dev, sizeof(*adev), GFP_KERNEL); ++ if (!adev) ++ return -ENOMEM; ++ ++ adev->dev = &pdev->dev; ++ ++ adev->regs = devm_platform_ioremap_resource(pdev, 0); ++ if (IS_ERR(adev->regs)) ++ return PTR_ERR(adev->regs); ++ ++ adev->irq = platform_get_irq(pdev, 0); ++ if (adev->irq < 0) ++ return adev->irq; ++ ++ ret = of_property_read_u32(pdev->dev.of_node, "qcom,ee", &adev->ee); ++ if (ret) { ++ dev_err(adev->dev, "Execution environment unspecified\n"); ++ return ret; ++ } ++ ++ adev->core_clk = devm_clk_get(adev->dev, "core"); ++ if (IS_ERR(adev->core_clk)) ++ return PTR_ERR(adev->core_clk); ++ ++ adev->iface_clk = devm_clk_get(adev->dev, "iface"); ++ if (IS_ERR(adev->iface_clk)) ++ return PTR_ERR(adev->iface_clk); ++ ++ adev->clk_reset = devm_reset_control_get_exclusive(&pdev->dev, "clk"); ++ if (IS_ERR(adev->clk_reset)) { ++ dev_err(adev->dev, "failed to get ADM0 reset\n"); ++ return PTR_ERR(adev->clk_reset); ++ } ++ ++ adev->c0_reset = devm_reset_control_get_exclusive(&pdev->dev, "c0"); ++ if (IS_ERR(adev->c0_reset)) { ++ dev_err(adev->dev, "failed to get ADM0 C0 reset\n"); ++ return PTR_ERR(adev->c0_reset); ++ } ++ ++ adev->c1_reset = devm_reset_control_get_exclusive(&pdev->dev, "c1"); ++ if (IS_ERR(adev->c1_reset)) { ++ dev_err(adev->dev, "failed to get ADM0 C1 reset\n"); ++ return PTR_ERR(adev->c1_reset); ++ } ++ ++ adev->c2_reset = devm_reset_control_get_exclusive(&pdev->dev, "c2"); ++ if (IS_ERR(adev->c2_reset)) { ++ dev_err(adev->dev, "failed to get ADM0 C2 reset\n"); ++ return PTR_ERR(adev->c2_reset); ++ } ++ ++ ret = clk_prepare_enable(adev->core_clk); ++ if (ret) { ++ dev_err(adev->dev, "failed to prepare/enable core clock\n"); ++ return ret; ++ } ++ ++ ret = clk_prepare_enable(adev->iface_clk); ++ if (ret) { ++ dev_err(adev->dev, "failed to prepare/enable iface clock\n"); ++ goto err_disable_core_clk; ++ } ++ ++ reset_control_assert(adev->clk_reset); ++ reset_control_assert(adev->c0_reset); ++ reset_control_assert(adev->c1_reset); ++ reset_control_assert(adev->c2_reset); ++ ++ udelay(2); ++ ++ reset_control_deassert(adev->clk_reset); ++ reset_control_deassert(adev->c0_reset); ++ reset_control_deassert(adev->c1_reset); ++ reset_control_deassert(adev->c2_reset); ++ ++ adev->channels = devm_kcalloc(adev->dev, ADM_MAX_CHANNELS, ++ sizeof(*adev->channels), GFP_KERNEL); ++ ++ if (!adev->channels) { ++ ret = -ENOMEM; ++ goto err_disable_clks; ++ } ++ ++ /* allocate and initialize channels */ ++ INIT_LIST_HEAD(&adev->common.channels); ++ ++ for (i = 0; i < ADM_MAX_CHANNELS; i++) ++ adm_channel_init(adev, &adev->channels[i], i); ++ ++ /* reset CRCIs */ ++ for (i = 0; i < 16; i++) ++ writel(ADM_CRCI_CTL_RST, adev->regs + ++ ADM_CRCI_CTL(i, adev->ee)); ++ ++ /* configure client interfaces */ ++ writel(ADM_CI_RANGE_START(0x40) | ADM_CI_RANGE_END(0xb0) | ++ ADM_CI_BURST_8_WORDS, adev->regs + ADM_CI_CONF(0)); ++ writel(ADM_CI_RANGE_START(0x2a) | ADM_CI_RANGE_END(0x2c) | ++ ADM_CI_BURST_8_WORDS, adev->regs + ADM_CI_CONF(1)); ++ writel(ADM_CI_RANGE_START(0x12) | ADM_CI_RANGE_END(0x28) | ++ ADM_CI_BURST_8_WORDS, adev->regs + ADM_CI_CONF(2)); ++ writel(ADM_GP_CTL_LP_EN | ADM_GP_CTL_LP_CNT(0xf), ++ adev->regs + ADM_GP_CTL); ++ ++ ret = devm_request_irq(adev->dev, adev->irq, adm_dma_irq, ++ 0, "adm_dma", adev); ++ if (ret) ++ goto err_disable_clks; ++ ++ platform_set_drvdata(pdev, adev); ++ ++ adev->common.dev = adev->dev; ++ adev->common.dev->dma_parms = &adev->dma_parms; ++ ++ /* set capabilities */ ++ dma_cap_zero(adev->common.cap_mask); ++ dma_cap_set(DMA_SLAVE, adev->common.cap_mask); ++ dma_cap_set(DMA_PRIVATE, adev->common.cap_mask); ++ ++ /* initialize dmaengine apis */ ++ adev->common.directions = BIT(DMA_DEV_TO_MEM | DMA_MEM_TO_DEV); ++ adev->common.residue_granularity = DMA_RESIDUE_GRANULARITY_DESCRIPTOR; ++ adev->common.src_addr_widths = DMA_SLAVE_BUSWIDTH_4_BYTES; ++ adev->common.dst_addr_widths = DMA_SLAVE_BUSWIDTH_4_BYTES; ++ adev->common.device_free_chan_resources = adm_free_chan; ++ adev->common.device_prep_slave_sg = adm_prep_slave_sg; ++ adev->common.device_issue_pending = adm_issue_pending; ++ adev->common.device_tx_status = adm_tx_status; ++ adev->common.device_terminate_all = adm_terminate_all; ++ adev->common.device_config = adm_slave_config; ++ ++ ret = dma_async_device_register(&adev->common); ++ if (ret) { ++ dev_err(adev->dev, "failed to register dma async device\n"); ++ goto err_disable_clks; ++ } ++ ++ ret = of_dma_controller_register(pdev->dev.of_node, ++ of_dma_xlate_by_chan_id, ++ &adev->common); ++ if (ret) ++ goto err_unregister_dma; ++ ++ return 0; ++ ++err_unregister_dma: ++ dma_async_device_unregister(&adev->common); ++err_disable_clks: ++ clk_disable_unprepare(adev->iface_clk); ++err_disable_core_clk: ++ clk_disable_unprepare(adev->core_clk); ++ ++ return ret; ++} ++ ++static int adm_dma_remove(struct platform_device *pdev) ++{ ++ struct adm_device *adev = platform_get_drvdata(pdev); ++ struct adm_chan *achan; ++ u32 i; ++ ++ of_dma_controller_free(pdev->dev.of_node); ++ dma_async_device_unregister(&adev->common); ++ ++ for (i = 0; i < ADM_MAX_CHANNELS; i++) { ++ achan = &adev->channels[i]; ++ ++ /* mask IRQs for this channel/EE pair */ ++ writel(0, adev->regs + ADM_CH_RSLT_CONF(achan->id, adev->ee)); ++ ++ tasklet_kill(&adev->channels[i].vc.task); ++ adm_terminate_all(&adev->channels[i].vc.chan); ++ } ++ ++ devm_free_irq(adev->dev, adev->irq, adev); ++ ++ clk_disable_unprepare(adev->core_clk); ++ clk_disable_unprepare(adev->iface_clk); ++ ++ return 0; ++} ++ ++static const struct of_device_id adm_of_match[] = { ++ { .compatible = "qcom,adm", }, ++ {} ++}; ++MODULE_DEVICE_TABLE(of, adm_of_match); ++ ++static struct platform_driver adm_dma_driver = { ++ .probe = adm_dma_probe, ++ .remove = adm_dma_remove, ++ .driver = { ++ .name = "adm-dma-engine", ++ .of_match_table = adm_of_match, ++ }, ++}; ++ ++module_platform_driver(adm_dma_driver); ++ ++MODULE_AUTHOR("Andy Gross "); ++MODULE_DESCRIPTION("QCOM ADM DMA engine driver"); ++MODULE_LICENSE("GPL v2"); diff --git a/target/linux/ipq806x/patches-5.15/101-5.12-mtd-parsers-Add-Qcom-SMEM-parser.patch b/target/linux/ipq806x/patches-5.15/101-5.12-mtd-parsers-Add-Qcom-SMEM-parser.patch new file mode 100644 index 0000000000..a78dc82a47 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/101-5.12-mtd-parsers-Add-Qcom-SMEM-parser.patch @@ -0,0 +1,217 @@ +From 803eb124e1a64e42888542c3444bfe6dac412c7f Mon Sep 17 00:00:00 2001 +From: Manivannan Sadhasivam +Date: Mon, 4 Jan 2021 09:41:35 +0530 +Subject: mtd: parsers: Add Qcom SMEM parser + +NAND based Qualcomm platforms have the partition table populated in the +Shared Memory (SMEM). Hence, add a parser for parsing the partitions +from it. + +Signed-off-by: Manivannan Sadhasivam +Signed-off-by: Miquel Raynal +Link: https://lore.kernel.org/linux-mtd/20210104041137.113075-3-manivannan.sadhasivam@linaro.org +--- + drivers/mtd/parsers/Kconfig | 8 ++ + drivers/mtd/parsers/Makefile | 1 + + drivers/mtd/parsers/qcomsmempart.c | 170 +++++++++++++++++++++++++++++++++++++ + 3 files changed, 179 insertions(+) + create mode 100644 drivers/mtd/parsers/qcomsmempart.c + +--- a/drivers/mtd/parsers/Kconfig ++++ b/drivers/mtd/parsers/Kconfig +@@ -196,6 +196,14 @@ config MTD_REDBOOT_PARTS_READONLY + + endif # MTD_REDBOOT_PARTS + ++config MTD_QCOMSMEM_PARTS ++ tristate "Qualcomm SMEM NAND flash partition parser" ++ depends on MTD_NAND_QCOM || COMPILE_TEST ++ depends on QCOM_SMEM ++ help ++ This provides support for parsing partitions from Shared Memory (SMEM) ++ for NAND flash on Qualcomm platforms. ++ + config MTD_ROUTERBOOT_PARTS + tristate "RouterBoot flash partition parser" + depends on MTD && OF +--- a/drivers/mtd/parsers/Makefile ++++ b/drivers/mtd/parsers/Makefile +@@ -13,4 +13,5 @@ obj-$(CONFIG_MTD_AFS_PARTS) += afs.o + obj-$(CONFIG_MTD_PARSER_TRX) += parser_trx.o + obj-$(CONFIG_MTD_SHARPSL_PARTS) += sharpslpart.o + obj-$(CONFIG_MTD_REDBOOT_PARTS) += redboot.o ++obj-$(CONFIG_MTD_QCOMSMEM_PARTS) += qcomsmempart.o + obj-$(CONFIG_MTD_ROUTERBOOT_PARTS) += routerbootpart.o +--- /dev/null ++++ b/drivers/mtd/parsers/qcomsmempart.c +@@ -0,0 +1,170 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++/* ++ * Qualcomm SMEM NAND flash partition parser ++ * ++ * Copyright (C) 2020, Linaro Ltd. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define SMEM_AARM_PARTITION_TABLE 9 ++#define SMEM_APPS 0 ++ ++#define SMEM_FLASH_PART_MAGIC1 0x55ee73aa ++#define SMEM_FLASH_PART_MAGIC2 0xe35ebddb ++#define SMEM_FLASH_PTABLE_V3 3 ++#define SMEM_FLASH_PTABLE_V4 4 ++#define SMEM_FLASH_PTABLE_MAX_PARTS_V3 16 ++#define SMEM_FLASH_PTABLE_MAX_PARTS_V4 48 ++#define SMEM_FLASH_PTABLE_HDR_LEN (4 * sizeof(u32)) ++#define SMEM_FLASH_PTABLE_NAME_SIZE 16 ++ ++/** ++ * struct smem_flash_pentry - SMEM Flash partition entry ++ * @name: Name of the partition ++ * @offset: Offset in blocks ++ * @length: Length of the partition in blocks ++ * @attr: Flags for this partition ++ */ ++struct smem_flash_pentry { ++ char name[SMEM_FLASH_PTABLE_NAME_SIZE]; ++ __le32 offset; ++ __le32 length; ++ u8 attr; ++} __packed __aligned(4); ++ ++/** ++ * struct smem_flash_ptable - SMEM Flash partition table ++ * @magic1: Partition table Magic 1 ++ * @magic2: Partition table Magic 2 ++ * @version: Partition table version ++ * @numparts: Number of partitions in this ptable ++ * @pentry: Flash partition entries belonging to this ptable ++ */ ++struct smem_flash_ptable { ++ __le32 magic1; ++ __le32 magic2; ++ __le32 version; ++ __le32 numparts; ++ struct smem_flash_pentry pentry[SMEM_FLASH_PTABLE_MAX_PARTS_V4]; ++} __packed __aligned(4); ++ ++static int parse_qcomsmem_part(struct mtd_info *mtd, ++ const struct mtd_partition **pparts, ++ struct mtd_part_parser_data *data) ++{ ++ struct smem_flash_pentry *pentry; ++ struct smem_flash_ptable *ptable; ++ size_t len = SMEM_FLASH_PTABLE_HDR_LEN; ++ struct mtd_partition *parts; ++ int ret, i, numparts; ++ char *name, *c; ++ ++ pr_debug("Parsing partition table info from SMEM\n"); ++ ptable = qcom_smem_get(SMEM_APPS, SMEM_AARM_PARTITION_TABLE, &len); ++ if (IS_ERR(ptable)) { ++ pr_err("Error reading partition table header\n"); ++ return PTR_ERR(ptable); ++ } ++ ++ /* Verify ptable magic */ ++ if (le32_to_cpu(ptable->magic1) != SMEM_FLASH_PART_MAGIC1 || ++ le32_to_cpu(ptable->magic2) != SMEM_FLASH_PART_MAGIC2) { ++ pr_err("Partition table magic verification failed\n"); ++ return -EINVAL; ++ } ++ ++ /* Ensure that # of partitions is less than the max we have allocated */ ++ numparts = le32_to_cpu(ptable->numparts); ++ if (numparts > SMEM_FLASH_PTABLE_MAX_PARTS_V4) { ++ pr_err("Partition numbers exceed the max limit\n"); ++ return -EINVAL; ++ } ++ ++ /* Find out length of partition data based on table version */ ++ if (le32_to_cpu(ptable->version) <= SMEM_FLASH_PTABLE_V3) { ++ len = SMEM_FLASH_PTABLE_HDR_LEN + SMEM_FLASH_PTABLE_MAX_PARTS_V3 * ++ sizeof(struct smem_flash_pentry); ++ } else if (le32_to_cpu(ptable->version) == SMEM_FLASH_PTABLE_V4) { ++ len = SMEM_FLASH_PTABLE_HDR_LEN + SMEM_FLASH_PTABLE_MAX_PARTS_V4 * ++ sizeof(struct smem_flash_pentry); ++ } else { ++ pr_err("Unknown ptable version (%d)", le32_to_cpu(ptable->version)); ++ return -EINVAL; ++ } ++ ++ /* ++ * Now that the partition table header has been parsed, verified ++ * and the length of the partition table calculated, read the ++ * complete partition table ++ */ ++ ptable = qcom_smem_get(SMEM_APPS, SMEM_AARM_PARTITION_TABLE, &len); ++ if (IS_ERR_OR_NULL(ptable)) { ++ pr_err("Error reading partition table\n"); ++ return PTR_ERR(ptable); ++ } ++ ++ parts = kcalloc(numparts, sizeof(*parts), GFP_KERNEL); ++ if (!parts) ++ return -ENOMEM; ++ ++ for (i = 0; i < numparts; i++) { ++ pentry = &ptable->pentry[i]; ++ if (pentry->name[0] == '\0') ++ continue; ++ ++ name = kstrdup(pentry->name, GFP_KERNEL); ++ if (!name) { ++ ret = -ENOMEM; ++ goto out_free_parts; ++ } ++ ++ /* Convert name to lower case */ ++ for (c = name; *c != '\0'; c++) ++ *c = tolower(*c); ++ ++ parts[i].name = name; ++ parts[i].offset = le32_to_cpu(pentry->offset) * mtd->erasesize; ++ parts[i].mask_flags = pentry->attr; ++ parts[i].size = le32_to_cpu(pentry->length) * mtd->erasesize; ++ pr_debug("%d: %s offs=0x%08x size=0x%08x attr:0x%08x\n", ++ i, pentry->name, le32_to_cpu(pentry->offset), ++ le32_to_cpu(pentry->length), pentry->attr); ++ } ++ ++ pr_debug("SMEM partition table found: ver: %d len: %d\n", ++ le32_to_cpu(ptable->version), numparts); ++ *pparts = parts; ++ ++ return numparts; ++ ++out_free_parts: ++ while (--i >= 0) ++ kfree(parts[i].name); ++ kfree(parts); ++ *pparts = NULL; ++ ++ return ret; ++} ++ ++static const struct of_device_id qcomsmem_of_match_table[] = { ++ { .compatible = "qcom,smem-part" }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, qcomsmem_of_match_table); ++ ++static struct mtd_part_parser mtd_parser_qcomsmem = { ++ .parse_fn = parse_qcomsmem_part, ++ .name = "qcomsmem", ++ .of_match_table = qcomsmem_of_match_table, ++}; ++module_mtd_part_parser(mtd_parser_qcomsmem); ++ ++MODULE_LICENSE("GPL v2"); ++MODULE_AUTHOR("Manivannan Sadhasivam "); ++MODULE_DESCRIPTION("Qualcomm SMEM NAND flash partition parser"); diff --git a/target/linux/ipq806x/patches-5.15/101-dwmac-ipq806x-qsgmii-pcs-all-ch-ctl.patch b/target/linux/ipq806x/patches-5.15/101-dwmac-ipq806x-qsgmii-pcs-all-ch-ctl.patch new file mode 100644 index 0000000000..2210f4e249 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/101-dwmac-ipq806x-qsgmii-pcs-all-ch-ctl.patch @@ -0,0 +1,83 @@ +--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c ++++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c +@@ -64,6 +64,17 @@ + #define NSS_COMMON_CLK_DIV_SGMII_100 4 + #define NSS_COMMON_CLK_DIV_SGMII_10 49 + ++#define QSGMII_PCS_ALL_CH_CTL 0x80 ++#define QSGMII_PCS_CH_SPEED_FORCE 0x2 ++#define QSGMII_PCS_CH_SPEED_10 0x0 ++#define QSGMII_PCS_CH_SPEED_100 0x4 ++#define QSGMII_PCS_CH_SPEED_1000 0x8 ++#define QSGMII_PCS_CH_SPEED_MASK (QSGMII_PCS_CH_SPEED_FORCE | \ ++ QSGMII_PCS_CH_SPEED_10 | \ ++ QSGMII_PCS_CH_SPEED_100 | \ ++ QSGMII_PCS_CH_SPEED_1000) ++#define QSGMII_PCS_CH_SPEED_SHIFT(x) (x * 4) ++ + #define QSGMII_PCS_CAL_LCKDT_CTL 0x120 + #define QSGMII_PCS_CAL_LCKDT_CTL_RST BIT(19) + +@@ -242,6 +253,36 @@ static void ipq806x_gmac_fix_mac_speed(v + ipq806x_gmac_set_speed(gmac, speed); + } + ++static int ++ipq806x_gmac_get_qsgmii_pcs_speed_val(struct platform_device *pdev) { ++ struct device_node *fixed_link_node; ++ int rv; ++ int fixed_link_speed; ++ ++ if (!of_phy_is_fixed_link(pdev->dev.of_node)) ++ return 0; ++ ++ fixed_link_node = of_get_child_by_name(pdev->dev.of_node, "fixed-link"); ++ if (!fixed_link_node) ++ return -1; ++ ++ rv = of_property_read_u32(fixed_link_node, "speed", &fixed_link_speed); ++ of_node_put(fixed_link_node); ++ if (rv) ++ return -1; ++ ++ switch (fixed_link_speed) { ++ case SPEED_1000: ++ return QSGMII_PCS_CH_SPEED_FORCE | QSGMII_PCS_CH_SPEED_1000; ++ case SPEED_100: ++ return QSGMII_PCS_CH_SPEED_FORCE | QSGMII_PCS_CH_SPEED_100; ++ case SPEED_10: ++ return QSGMII_PCS_CH_SPEED_FORCE | QSGMII_PCS_CH_SPEED_10; ++ } ++ ++ return -1; ++} ++ + static int ipq806x_gmac_probe(struct platform_device *pdev) + { + struct plat_stmmacenet_data *plat_dat; +@@ -250,6 +291,7 @@ static int ipq806x_gmac_probe(struct pla + struct ipq806x_gmac *gmac; + int val; + int err; ++ int qsgmii_pcs_speed; + + val = stmmac_get_platform_resources(pdev, &stmmac_res); + if (val) +@@ -339,6 +381,17 @@ static int ipq806x_gmac_probe(struct pla + 0x1ul << QSGMII_PHY_RX_INPUT_EQU_OFFSET | + 0x2ul << QSGMII_PHY_CDR_PI_SLEW_OFFSET | + 0xCul << QSGMII_PHY_TX_DRV_AMP_OFFSET); ++ ++ qsgmii_pcs_speed = ipq806x_gmac_get_qsgmii_pcs_speed_val(pdev); ++ if (qsgmii_pcs_speed != -1) { ++ regmap_update_bits( ++ gmac->qsgmii_csr, ++ QSGMII_PCS_ALL_CH_CTL, ++ QSGMII_PCS_CH_SPEED_MASK << ++ QSGMII_PCS_CH_SPEED_SHIFT(gmac->id), ++ qsgmii_pcs_speed << ++ QSGMII_PCS_CH_SPEED_SHIFT(gmac->id)); ++ } + } + + plat_dat->has_gmac = true; diff --git a/target/linux/ipq806x/patches-5.15/102-mtd-rootfs-conflicts-with-OpenWrt-auto-mounting.patch b/target/linux/ipq806x/patches-5.15/102-mtd-rootfs-conflicts-with-OpenWrt-auto-mounting.patch new file mode 100644 index 0000000000..e83872935f --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/102-mtd-rootfs-conflicts-with-OpenWrt-auto-mounting.patch @@ -0,0 +1,24 @@ +From 5001f2e1a325b68dbf225bd17f69a4d3d975cca5 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Thu, 9 Mar 2017 09:31:44 +0100 +Subject: [PATCH 61/69] mtd: "rootfs" conflicts with OpenWrt auto mounting + +Signed-off-by: John Crispin +--- + drivers/mtd/parsers/qcomsmempart.c | 4 ++++ + 1 file changed, 4 insertions(+) + +--- a/drivers/mtd/parsers/qcomsmempart.c ++++ b/drivers/mtd/parsers/qcomsmempart.c +@@ -132,6 +132,11 @@ static int parse_qcomsmem_part(struct mt + parts[i].offset = le32_to_cpu(pentry->offset) * mtd->erasesize; + parts[i].mask_flags = pentry->attr; + parts[i].size = le32_to_cpu(pentry->length) * mtd->erasesize; ++ ++ /* "rootfs" conflicts with OpenWrt auto mounting */ ++ if (mtd_type_is_nand(mtd) && !strcmp(name, "rootfs")) ++ parts[i].name = "ubi"; ++ + pr_debug("%d: %s offs=0x%08x size=0x%08x attr:0x%08x\n", + i, pentry->name, le32_to_cpu(pentry->offset), + le32_to_cpu(pentry->length), pentry->attr); diff --git a/target/linux/ipq806x/patches-5.15/103-ARM-dts-qcom-reduce-pci-IO-size-to-64K.patch b/target/linux/ipq806x/patches-5.15/103-ARM-dts-qcom-reduce-pci-IO-size-to-64K.patch new file mode 100644 index 0000000000..75b53234ab --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/103-ARM-dts-qcom-reduce-pci-IO-size-to-64K.patch @@ -0,0 +1,46 @@ +From 84909e85881d67244240c9f40974ce12a51e3886 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Tue, 11 May 2021 23:09:45 +0200 +Subject: [PATCH] ARM: dts: qcom: reduce pci IO size to 64K + +The current value is probably a typo and is actually uncommon to find +1MB IO space even on a x86 arch. Also with recent changes to the pci +driver, pci1 and pci2 now fails to function as any connected device +fails any reg read/write. Reduce this to 64K as it should be more than +enough and 3 * 64K of total IO space doesn't exceed the IO_SPACE_LIMIT +hardcoded for the ARM arch. + +Signed-off-by: Ansuel Smith +--- + arch/arm/boot/dts/qcom-ipq8064.dtsi | 6 +++--- + 1 file changed, 3 insertions(+), 3 deletions(-) + +--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi +@@ -1163,7 +1163,7 @@ + #address-cells = <3>; + #size-cells = <2>; + +- ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000 /* downstream I/O */ ++ ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */ + + interrupts = ; +@@ -1214,7 +1214,7 @@ + #address-cells = <3>; + #size-cells = <2>; + +- ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000 /* downstream I/O */ ++ ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */ + + interrupts = ; +@@ -1265,7 +1265,7 @@ + #address-cells = <3>; + #size-cells = <2>; + +- ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000 /* downstream I/O */ ++ ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */ + + interrupts = ; diff --git a/target/linux/ipq806x/patches-5.15/104-1-drivers-thermal-tsens-Add-VER_0-tsens-version.patch b/target/linux/ipq806x/patches-5.15/104-1-drivers-thermal-tsens-Add-VER_0-tsens-version.patch new file mode 100644 index 0000000000..8627244c59 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/104-1-drivers-thermal-tsens-Add-VER_0-tsens-version.patch @@ -0,0 +1,285 @@ +From 5c7d1181056feef0b58fb2f556f55e170ba5b479 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Sat, 25 Jul 2020 19:14:59 +0200 +Subject: [PATCH 01/10] drivers: thermal: tsens: Add VER_0 tsens version + +VER_0 is used to describe device based on tsens version before v0.1. +These device are devices based on msm8960 for example apq8064 or +ipq806x. + +Signed-off-by: Ansuel Smith +Reviewed-by: Thara Gopinath +Reported-by: kernel test robot +Reported-by: Dan Carpenter +--- + drivers/thermal/qcom/tsens.c | 150 ++++++++++++++++++++++++++++------- + drivers/thermal/qcom/tsens.h | 4 +- + 2 files changed, 124 insertions(+), 30 deletions(-) + +--- a/drivers/thermal/qcom/tsens.c ++++ b/drivers/thermal/qcom/tsens.c +@@ -12,6 +12,7 @@ + #include + #include + #include ++#include + #include + #include + #include +@@ -515,6 +516,15 @@ static irqreturn_t tsens_irq_thread(int + dev_dbg(priv->dev, "[%u] %s: no violation: %d\n", + hw_id, __func__, temp); + } ++ ++ if (tsens_version(priv) < VER_0_1) { ++ /* Constraint: There is only 1 interrupt control register for all ++ * 11 temperature sensor. So monitoring more than 1 sensor based ++ * on interrupts will yield inconsistent result. To overcome this ++ * issue we will monitor only sensor 0 which is the master sensor. ++ */ ++ break; ++ } + } + + return IRQ_HANDLED; +@@ -530,6 +540,13 @@ static int tsens_set_trips(void *_sensor + int high_val, low_val, cl_high, cl_low; + u32 hw_id = s->hw_id; + ++ if (tsens_version(priv) < VER_0_1) { ++ /* Pre v0.1 IP had a single register for each type of interrupt ++ * and thresholds ++ */ ++ hw_id = 0; ++ } ++ + dev_dbg(dev, "[%u] %s: proposed thresholds: (%d:%d)\n", + hw_id, __func__, low, high); + +@@ -584,18 +601,21 @@ int get_temp_tsens_valid(const struct ts + u32 valid; + int ret; + +- ret = regmap_field_read(priv->rf[valid_idx], &valid); +- if (ret) +- return ret; +- while (!valid) { +- /* Valid bit is 0 for 6 AHB clock cycles. +- * At 19.2MHz, 1 AHB clock is ~60ns. +- * We should enter this loop very, very rarely. +- */ +- ndelay(400); ++ /* VER_0 doesn't have VALID bit */ ++ if (tsens_version(priv) >= VER_0_1) { + ret = regmap_field_read(priv->rf[valid_idx], &valid); + if (ret) + return ret; ++ while (!valid) { ++ /* Valid bit is 0 for 6 AHB clock cycles. ++ * At 19.2MHz, 1 AHB clock is ~60ns. ++ * We should enter this loop very, very rarely. ++ */ ++ ndelay(400); ++ ret = regmap_field_read(priv->rf[valid_idx], &valid); ++ if (ret) ++ return ret; ++ } + } + + /* Valid bit is set, OK to read the temperature */ +@@ -608,15 +628,29 @@ int get_temp_common(const struct tsens_s + { + struct tsens_priv *priv = s->priv; + int hw_id = s->hw_id; +- int last_temp = 0, ret; ++ int last_temp = 0, ret, trdy; ++ unsigned long timeout; + +- ret = regmap_field_read(priv->rf[LAST_TEMP_0 + hw_id], &last_temp); +- if (ret) +- return ret; ++ timeout = jiffies + usecs_to_jiffies(TIMEOUT_US); ++ do { ++ if (tsens_version(priv) == VER_0) { ++ ret = regmap_field_read(priv->rf[TRDY], &trdy); ++ if (ret) ++ return ret; ++ if (!trdy) ++ continue; ++ } + +- *temp = code_to_degc(last_temp, s) * 1000; ++ ret = regmap_field_read(priv->rf[LAST_TEMP_0 + hw_id], &last_temp); ++ if (ret) ++ return ret; + +- return 0; ++ *temp = code_to_degc(last_temp, s) * 1000; ++ ++ return 0; ++ } while (time_before(jiffies, timeout)); ++ ++ return -ETIMEDOUT; + } + + #ifdef CONFIG_DEBUG_FS +@@ -738,19 +772,34 @@ int __init init_common(struct tsens_priv + priv->tm_offset = 0x1000; + } + +- res = platform_get_resource(op, IORESOURCE_MEM, 0); +- tm_base = devm_ioremap_resource(dev, res); +- if (IS_ERR(tm_base)) { +- ret = PTR_ERR(tm_base); +- goto err_put_device; ++ if (tsens_version(priv) >= VER_0_1) { ++ res = platform_get_resource(op, IORESOURCE_MEM, 0); ++ tm_base = devm_ioremap_resource(dev, res); ++ if (IS_ERR(tm_base)) { ++ ret = PTR_ERR(tm_base); ++ goto err_put_device; ++ } ++ ++ priv->tm_map = devm_regmap_init_mmio(dev, tm_base, &tsens_config); ++ } else { /* VER_0 share the same gcc regs using a syscon */ ++ struct device *parent = priv->dev->parent; ++ ++ if (parent) ++ priv->tm_map = syscon_node_to_regmap(parent->of_node); + } + +- priv->tm_map = devm_regmap_init_mmio(dev, tm_base, &tsens_config); +- if (IS_ERR(priv->tm_map)) { +- ret = PTR_ERR(priv->tm_map); ++ if (IS_ERR_OR_NULL(priv->tm_map)) { ++ if (!priv->tm_map) ++ ret = -ENODEV; ++ else ++ ret = PTR_ERR(priv->tm_map); + goto err_put_device; + } + ++ /* VER_0 have only tm_map */ ++ if (!priv->srot_map) ++ priv->srot_map = priv->tm_map; ++ + if (tsens_version(priv) > VER_0_1) { + for (i = VER_MAJOR; i <= VER_STEP; i++) { + priv->rf[i] = devm_regmap_field_alloc(dev, priv->srot_map, +@@ -771,6 +820,10 @@ int __init init_common(struct tsens_priv + ret = PTR_ERR(priv->rf[TSENS_EN]); + goto err_put_device; + } ++ /* in VER_0 TSENS need to be explicitly enabled */ ++ if (tsens_version(priv) == VER_0) ++ regmap_field_write(priv->rf[TSENS_EN], 1); ++ + ret = regmap_field_read(priv->rf[TSENS_EN], &enabled); + if (ret) + goto err_put_device; +@@ -793,6 +846,19 @@ int __init init_common(struct tsens_priv + goto err_put_device; + } + ++ priv->rf[TSENS_SW_RST] = ++ devm_regmap_field_alloc(dev, priv->srot_map, priv->fields[TSENS_SW_RST]); ++ if (IS_ERR(priv->rf[TSENS_SW_RST])) { ++ ret = PTR_ERR(priv->rf[TSENS_SW_RST]); ++ goto err_put_device; ++ } ++ ++ priv->rf[TRDY] = devm_regmap_field_alloc(dev, priv->tm_map, priv->fields[TRDY]); ++ if (IS_ERR(priv->rf[TRDY])) { ++ ret = PTR_ERR(priv->rf[TRDY]); ++ goto err_put_device; ++ } ++ + /* This loop might need changes if enum regfield_ids is reordered */ + for (j = LAST_TEMP_0; j <= UP_THRESH_15; j += 16) { + for (i = 0; i < priv->feat->max_sensors; i++) { +@@ -808,7 +874,7 @@ int __init init_common(struct tsens_priv + } + } + +- if (priv->feat->crit_int) { ++ if (priv->feat->crit_int || tsens_version(priv) < VER_0_1) { + /* Loop might need changes if enum regfield_ids is reordered */ + for (j = CRITICAL_STATUS_0; j <= CRIT_THRESH_15; j += 16) { + for (i = 0; i < priv->feat->max_sensors; i++) { +@@ -846,7 +912,11 @@ int __init init_common(struct tsens_priv + } + + spin_lock_init(&priv->ul_lock); +- tsens_enable_irq(priv); ++ ++ /* VER_0 interrupt doesn't need to be enabled */ ++ if (tsens_version(priv) >= VER_0_1) ++ tsens_enable_irq(priv); ++ + tsens_debug_init(op); + + err_put_device: +@@ -945,10 +1015,19 @@ static int tsens_register_irq(struct tse + if (irq == -ENXIO) + ret = 0; + } else { +- ret = devm_request_threaded_irq(&pdev->dev, irq, +- NULL, thread_fn, +- IRQF_ONESHOT, +- dev_name(&pdev->dev), priv); ++ /* VER_0 interrupt is TRIGGER_RISING, VER_0_1 and up is ONESHOT */ ++ if (tsens_version(priv) == VER_0) ++ ret = devm_request_threaded_irq(&pdev->dev, irq, ++ thread_fn, NULL, ++ IRQF_TRIGGER_RISING, ++ dev_name(&pdev->dev), ++ priv); ++ else ++ ret = devm_request_threaded_irq(&pdev->dev, irq, NULL, ++ thread_fn, IRQF_ONESHOT, ++ dev_name(&pdev->dev), ++ priv); ++ + if (ret) + dev_err(&pdev->dev, "%s: failed to get irq\n", + __func__); +@@ -977,6 +1056,19 @@ static int tsens_register(struct tsens_p + priv->ops->enable(priv, i); + } + ++ /* VER_0 require to set MIN and MAX THRESH ++ * These 2 regs are set using the: ++ * - CRIT_THRESH_0 for MAX THRESH hardcoded to 120°C ++ * - CRIT_THRESH_1 for MIN THRESH hardcoded to 0°C ++ */ ++ if (tsens_version(priv) < VER_0_1) { ++ regmap_field_write(priv->rf[CRIT_THRESH_0], ++ tsens_mC_to_hw(priv->sensor, 120000)); ++ ++ regmap_field_write(priv->rf[CRIT_THRESH_1], ++ tsens_mC_to_hw(priv->sensor, 0)); ++ } ++ + ret = tsens_register_irq(priv, "uplow", tsens_irq_thread); + if (ret < 0) + return ret; +--- a/drivers/thermal/qcom/tsens.h ++++ b/drivers/thermal/qcom/tsens.h +@@ -13,6 +13,7 @@ + #define CAL_DEGC_PT2 120 + #define SLOPE_FACTOR 1000 + #define SLOPE_DEFAULT 3200 ++#define TIMEOUT_US 100 + #define THRESHOLD_MAX_ADC_CODE 0x3ff + #define THRESHOLD_MIN_ADC_CODE 0x0 + +@@ -25,7 +26,8 @@ struct tsens_priv; + + /* IP version numbers in ascending order */ + enum tsens_ver { +- VER_0_1 = 0, ++ VER_0 = 0, ++ VER_0_1, + VER_1_X, + VER_2_X, + }; diff --git a/target/linux/ipq806x/patches-5.15/104-2-drivers-thermal-tsens-Don-t-hardcode-sensor-slope.patch b/target/linux/ipq806x/patches-5.15/104-2-drivers-thermal-tsens-Don-t-hardcode-sensor-slope.patch new file mode 100644 index 0000000000..109f524bbd --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/104-2-drivers-thermal-tsens-Don-t-hardcode-sensor-slope.patch @@ -0,0 +1,28 @@ +From efa0d50a6c5ec7619371dfe4d3e6ca54b73787d5 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Wed, 25 Nov 2020 16:47:21 +0100 +Subject: [PATCH 02/10] drivers: thermal: tsens: Don't hardcode sensor slope + +Function compute_intercept_slope hardcode the sensor slope to +SLOPE_DEFAULT. Change this and use the default value only if a slope is +not defined. This is needed for tsens VER_0 that has a hardcoded slope +table. + +Signed-off-by: Ansuel Smith +Reviewed-by: Thara Gopinath +--- + drivers/thermal/qcom/tsens.c | 3 ++- + 1 file changed, 2 insertions(+), 1 deletion(-) + +--- a/drivers/thermal/qcom/tsens.c ++++ b/drivers/thermal/qcom/tsens.c +@@ -86,7 +86,8 @@ void compute_intercept_slope(struct tsen + "%s: sensor%d - data_point1:%#x data_point2:%#x\n", + __func__, i, p1[i], p2[i]); + +- priv->sensor[i].slope = SLOPE_DEFAULT; ++ if (!priv->sensor[i].slope) ++ priv->sensor[i].slope = SLOPE_DEFAULT; + if (mode == TWO_PT_CALIB) { + /* + * slope (m) = adc_code2 - adc_code1 (y2 - y1)/ diff --git a/target/linux/ipq806x/patches-5.15/104-3-drivers-thermal-tsens-Convert-msm8960-to-reg_field.patch b/target/linux/ipq806x/patches-5.15/104-3-drivers-thermal-tsens-Convert-msm8960-to-reg_field.patch new file mode 100644 index 0000000000..bf378107c6 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/104-3-drivers-thermal-tsens-Convert-msm8960-to-reg_field.patch @@ -0,0 +1,119 @@ +From 6bac2e2fa36c2d7c304768a689d8b73155b90aa2 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Wed, 25 Nov 2020 17:15:51 +0100 +Subject: [PATCH 03/10] drivers: thermal: tsens: Convert msm8960 to reg_field + +Convert msm9860 driver to reg_field to use the init_common +function. + +Signed-off-by: Ansuel Smith +Acked-by: Thara Gopinath +--- + drivers/thermal/qcom/tsens-8960.c | 80 ++++++++++++++++++++++++++++++- + 1 file changed, 79 insertions(+), 1 deletion(-) + +--- a/drivers/thermal/qcom/tsens-8960.c ++++ b/drivers/thermal/qcom/tsens-8960.c +@@ -51,11 +51,22 @@ + #define MIN_LIMIT_TH 0x0 + #define MAX_LIMIT_TH 0xff + +-#define S0_STATUS_ADDR 0x3628 + #define INT_STATUS_ADDR 0x363c + #define TRDY_MASK BIT(7) + #define TIMEOUT_US 100 + ++#define S0_STATUS_OFF 0x3628 ++#define S1_STATUS_OFF 0x362c ++#define S2_STATUS_OFF 0x3630 ++#define S3_STATUS_OFF 0x3634 ++#define S4_STATUS_OFF 0x3638 ++#define S5_STATUS_OFF 0x3664 /* Sensors 5-10 found on apq8064/msm8960 */ ++#define S6_STATUS_OFF 0x3668 ++#define S7_STATUS_OFF 0x366c ++#define S8_STATUS_OFF 0x3670 ++#define S9_STATUS_OFF 0x3674 ++#define S10_STATUS_OFF 0x3678 ++ + static int suspend_8960(struct tsens_priv *priv) + { + int ret; +@@ -269,6 +280,71 @@ static int get_temp_8960(const struct ts + return -ETIMEDOUT; + } + ++static struct tsens_features tsens_8960_feat = { ++ .ver_major = VER_0, ++ .crit_int = 0, ++ .adc = 1, ++ .srot_split = 0, ++ .max_sensors = 11, ++}; ++ ++static const struct reg_field tsens_8960_regfields[MAX_REGFIELDS] = { ++ /* ----- SROT ------ */ ++ /* No VERSION information */ ++ ++ /* CNTL */ ++ [TSENS_EN] = REG_FIELD(CNTL_ADDR, 0, 0), ++ [TSENS_SW_RST] = REG_FIELD(CNTL_ADDR, 1, 1), ++ /* 8960 has 5 sensors, 8660 has 11, we only handle 5 */ ++ [SENSOR_EN] = REG_FIELD(CNTL_ADDR, 3, 7), ++ ++ /* ----- TM ------ */ ++ /* INTERRUPT ENABLE */ ++ /* NO INTERRUPT ENABLE */ ++ ++ /* Single UPPER/LOWER TEMPERATURE THRESHOLD for all sensors */ ++ [LOW_THRESH_0] = REG_FIELD(THRESHOLD_ADDR, 0, 7), ++ [UP_THRESH_0] = REG_FIELD(THRESHOLD_ADDR, 8, 15), ++ /* MIN_THRESH_0 and MAX_THRESH_0 are not present in the regfield ++ * Recycle CRIT_THRESH_0 and 1 to set the required regs to hardcoded temp ++ * MIN_THRESH_0 -> CRIT_THRESH_1 ++ * MAX_THRESH_0 -> CRIT_THRESH_0 ++ */ ++ [CRIT_THRESH_1] = REG_FIELD(THRESHOLD_ADDR, 16, 23), ++ [CRIT_THRESH_0] = REG_FIELD(THRESHOLD_ADDR, 24, 31), ++ ++ /* UPPER/LOWER INTERRUPT [CLEAR/STATUS] */ ++ /* 1 == clear, 0 == normal operation */ ++ [LOW_INT_CLEAR_0] = REG_FIELD(CNTL_ADDR, 9, 9), ++ [UP_INT_CLEAR_0] = REG_FIELD(CNTL_ADDR, 10, 10), ++ ++ /* NO CRITICAL INTERRUPT SUPPORT on 8960 */ ++ ++ /* Sn_STATUS */ ++ [LAST_TEMP_0] = REG_FIELD(S0_STATUS_OFF, 0, 7), ++ [LAST_TEMP_1] = REG_FIELD(S1_STATUS_OFF, 0, 7), ++ [LAST_TEMP_2] = REG_FIELD(S2_STATUS_OFF, 0, 7), ++ [LAST_TEMP_3] = REG_FIELD(S3_STATUS_OFF, 0, 7), ++ [LAST_TEMP_4] = REG_FIELD(S4_STATUS_OFF, 0, 7), ++ [LAST_TEMP_5] = REG_FIELD(S5_STATUS_OFF, 0, 7), ++ [LAST_TEMP_6] = REG_FIELD(S6_STATUS_OFF, 0, 7), ++ [LAST_TEMP_7] = REG_FIELD(S7_STATUS_OFF, 0, 7), ++ [LAST_TEMP_8] = REG_FIELD(S8_STATUS_OFF, 0, 7), ++ [LAST_TEMP_9] = REG_FIELD(S9_STATUS_OFF, 0, 7), ++ [LAST_TEMP_10] = REG_FIELD(S10_STATUS_OFF, 0, 7), ++ ++ /* No VALID field on 8960 */ ++ /* TSENS_INT_STATUS bits: 1 == threshold violated */ ++ [MIN_STATUS_0] = REG_FIELD(INT_STATUS_ADDR, 0, 0), ++ [LOWER_STATUS_0] = REG_FIELD(INT_STATUS_ADDR, 1, 1), ++ [UPPER_STATUS_0] = REG_FIELD(INT_STATUS_ADDR, 2, 2), ++ /* No CRITICAL field on 8960 */ ++ [MAX_STATUS_0] = REG_FIELD(INT_STATUS_ADDR, 3, 3), ++ ++ /* TRDY: 1=ready, 0=in progress */ ++ [TRDY] = REG_FIELD(INT_STATUS_ADDR, 7, 7), ++}; ++ + static const struct tsens_ops ops_8960 = { + .init = init_8960, + .calibrate = calibrate_8960, +@@ -282,4 +358,6 @@ static const struct tsens_ops ops_8960 = + struct tsens_plat_data data_8960 = { + .num_sensors = 11, + .ops = &ops_8960, ++ .feat = &tsens_8960_feat, ++ .fields = tsens_8960_regfields, + }; diff --git a/target/linux/ipq806x/patches-5.15/104-4-drivers-thermal-tsens-Use-init_common-for-msm8960.patch b/target/linux/ipq806x/patches-5.15/104-4-drivers-thermal-tsens-Use-init_common-for-msm8960.patch new file mode 100644 index 0000000000..ae8a52c100 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/104-4-drivers-thermal-tsens-Use-init_common-for-msm8960.patch @@ -0,0 +1,81 @@ +From c04f98a496929f75d75c65115d5717423c3d0634 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Wed, 25 Nov 2020 17:16:36 +0100 +Subject: [PATCH 04/10] drivers: thermal: tsens: Use init_common for msm8960 + +Use init_common and drop custom init for msm8960. + +Signed-off-by: Ansuel Smith +Reviewed-by: Thara Gopinath +--- + drivers/thermal/qcom/tsens-8960.c | 52 +------------------------------ + 1 file changed, 1 insertion(+), 51 deletions(-) + +--- a/drivers/thermal/qcom/tsens-8960.c ++++ b/drivers/thermal/qcom/tsens-8960.c +@@ -173,56 +173,6 @@ static void disable_8960(struct tsens_pr + regmap_write(priv->tm_map, CNTL_ADDR, reg_cntl); + } + +-static int init_8960(struct tsens_priv *priv) +-{ +- int ret, i; +- u32 reg_cntl; +- +- priv->tm_map = dev_get_regmap(priv->dev, NULL); +- if (!priv->tm_map) +- return -ENODEV; +- +- /* +- * The status registers for each sensor are discontiguous +- * because some SoCs have 5 sensors while others have more +- * but the control registers stay in the same place, i.e +- * directly after the first 5 status registers. +- */ +- for (i = 0; i < priv->num_sensors; i++) { +- if (i >= 5) +- priv->sensor[i].status = S0_STATUS_ADDR + 40; +- priv->sensor[i].status += i * 4; +- } +- +- reg_cntl = SW_RST; +- ret = regmap_update_bits(priv->tm_map, CNTL_ADDR, SW_RST, reg_cntl); +- if (ret) +- return ret; +- +- if (priv->num_sensors > 1) { +- reg_cntl |= SLP_CLK_ENA | (MEASURE_PERIOD << 18); +- reg_cntl &= ~SW_RST; +- ret = regmap_update_bits(priv->tm_map, CONFIG_ADDR, +- CONFIG_MASK, CONFIG); +- } else { +- reg_cntl |= SLP_CLK_ENA_8660 | (MEASURE_PERIOD << 16); +- reg_cntl &= ~CONFIG_MASK_8660; +- reg_cntl |= CONFIG_8660 << CONFIG_SHIFT_8660; +- } +- +- reg_cntl |= GENMASK(priv->num_sensors - 1, 0) << SENSOR0_SHIFT; +- ret = regmap_write(priv->tm_map, CNTL_ADDR, reg_cntl); +- if (ret) +- return ret; +- +- reg_cntl |= EN; +- ret = regmap_write(priv->tm_map, CNTL_ADDR, reg_cntl); +- if (ret) +- return ret; +- +- return 0; +-} +- + static int calibrate_8960(struct tsens_priv *priv) + { + int i; +@@ -346,7 +296,7 @@ static const struct reg_field tsens_8960 + }; + + static const struct tsens_ops ops_8960 = { +- .init = init_8960, ++ .init = init_common, + .calibrate = calibrate_8960, + .get_temp = get_temp_8960, + .enable = enable_8960, diff --git a/target/linux/ipq806x/patches-5.15/104-5-drivers-thermal-tsens-Fix-bug-in-sensor-enable-for-m.patch b/target/linux/ipq806x/patches-5.15/104-5-drivers-thermal-tsens-Fix-bug-in-sensor-enable-for-m.patch new file mode 100644 index 0000000000..7b01a67d90 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/104-5-drivers-thermal-tsens-Fix-bug-in-sensor-enable-for-m.patch @@ -0,0 +1,66 @@ +From b3e8bd33b84a6b6c863bd1733bd15b5f1483b8ab Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Wed, 25 Nov 2020 17:06:55 +0100 +Subject: [PATCH 05/10] drivers: thermal: tsens: Fix bug in sensor enable for + msm8960 + +Device based on tsens VER_0 contains a hardware bug that results in some +problem with sensor enablement. Sensor id 6-11 can't be enabled +selectively and all of them must be enabled in one step. + +Signed-off-by: Ansuel Smith +Acked-by: Thara Gopinath +--- + drivers/thermal/qcom/tsens-8960.c | 23 ++++++++++++++++++++--- + 1 file changed, 20 insertions(+), 3 deletions(-) + +--- a/drivers/thermal/qcom/tsens-8960.c ++++ b/drivers/thermal/qcom/tsens-8960.c +@@ -27,9 +27,9 @@ + #define EN BIT(0) + #define SW_RST BIT(1) + #define SENSOR0_EN BIT(3) ++#define MEASURE_PERIOD BIT(18) + #define SLP_CLK_ENA BIT(26) + #define SLP_CLK_ENA_8660 BIT(24) +-#define MEASURE_PERIOD 1 + #define SENSOR0_SHIFT 3 + + /* INT_STATUS_ADDR bitmasks */ +@@ -126,17 +126,34 @@ static int resume_8960(struct tsens_priv + static int enable_8960(struct tsens_priv *priv, int id) + { + int ret; +- u32 reg, mask; ++ u32 reg, mask = BIT(id); + + ret = regmap_read(priv->tm_map, CNTL_ADDR, ®); + if (ret) + return ret; + +- mask = BIT(id + SENSOR0_SHIFT); ++ /* HARDWARE BUG: ++ * On platforms with more than 6 sensors, all remaining sensors ++ * must be enabled together, otherwise undefined results are expected. ++ * (Sensor 6-7 disabled, Sensor 3 disabled...) In the original driver, ++ * all the sensors are enabled in one step hence this bug is not ++ * triggered. ++ */ ++ if (id > 5) ++ mask = GENMASK(10, 6); ++ ++ mask <<= SENSOR0_SHIFT; ++ ++ /* Sensors already enabled. Skip. */ ++ if ((reg & mask) == mask) ++ return 0; ++ + ret = regmap_write(priv->tm_map, CNTL_ADDR, reg | SW_RST); + if (ret) + return ret; + ++ reg |= MEASURE_PERIOD; ++ + if (priv->num_sensors > 1) + reg |= mask | SLP_CLK_ENA | EN; + else diff --git a/target/linux/ipq806x/patches-5.15/104-6-drivers-thermal-tsens-Replace-custom-8960-apis-with-.patch b/target/linux/ipq806x/patches-5.15/104-6-drivers-thermal-tsens-Replace-custom-8960-apis-with-.patch new file mode 100644 index 0000000000..a82f596954 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/104-6-drivers-thermal-tsens-Replace-custom-8960-apis-with-.patch @@ -0,0 +1,109 @@ +From 1ff9f982051759e0387e8c7e793b49c48eae291d Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Wed, 25 Nov 2020 17:11:05 +0100 +Subject: [PATCH 06/10] drivers: thermal: tsens: Replace custom 8960 apis with + generic apis + +Rework calibrate function to use common function. Derive the offset from +a missing hardcoded slope table and the data from the nvmem calib +efuses. +Drop custom get_temp function and use generic api. + +Signed-off-by: Ansuel Smith +Acked-by: Thara Gopinath +--- + drivers/thermal/qcom/tsens-8960.c | 56 +++++++++---------------------- + 1 file changed, 15 insertions(+), 41 deletions(-) + +--- a/drivers/thermal/qcom/tsens-8960.c ++++ b/drivers/thermal/qcom/tsens-8960.c +@@ -67,6 +67,13 @@ + #define S9_STATUS_OFF 0x3674 + #define S10_STATUS_OFF 0x3678 + ++/* Original slope - 200 to compensate mC to C inaccuracy */ ++static u32 tsens_msm8960_slope[] = { ++ 976, 976, 954, 976, ++ 911, 932, 932, 999, ++ 932, 999, 932 ++ }; ++ + static int suspend_8960(struct tsens_priv *priv) + { + int ret; +@@ -194,9 +201,7 @@ static int calibrate_8960(struct tsens_p + { + int i; + char *data; +- +- ssize_t num_read = priv->num_sensors; +- struct tsens_sensor *s = priv->sensor; ++ u32 p1[11]; + + data = qfprom_read(priv->dev, "calib"); + if (IS_ERR(data)) +@@ -204,49 +209,18 @@ static int calibrate_8960(struct tsens_p + if (IS_ERR(data)) + return PTR_ERR(data); + +- for (i = 0; i < num_read; i++, s++) +- s->offset = data[i]; ++ for (i = 0; i < priv->num_sensors; i++) { ++ p1[i] = data[i]; ++ priv->sensor[i].slope = tsens_msm8960_slope[i]; ++ } ++ ++ compute_intercept_slope(priv, p1, NULL, ONE_PT_CALIB); + + kfree(data); + + return 0; + } + +-/* Temperature on y axis and ADC-code on x-axis */ +-static inline int code_to_mdegC(u32 adc_code, const struct tsens_sensor *s) +-{ +- int slope, offset; +- +- slope = thermal_zone_get_slope(s->tzd); +- offset = CAL_MDEGC - slope * s->offset; +- +- return adc_code * slope + offset; +-} +- +-static int get_temp_8960(const struct tsens_sensor *s, int *temp) +-{ +- int ret; +- u32 code, trdy; +- struct tsens_priv *priv = s->priv; +- unsigned long timeout; +- +- timeout = jiffies + usecs_to_jiffies(TIMEOUT_US); +- do { +- ret = regmap_read(priv->tm_map, INT_STATUS_ADDR, &trdy); +- if (ret) +- return ret; +- if (!(trdy & TRDY_MASK)) +- continue; +- ret = regmap_read(priv->tm_map, s->status, &code); +- if (ret) +- return ret; +- *temp = code_to_mdegC(code, s); +- return 0; +- } while (time_before(jiffies, timeout)); +- +- return -ETIMEDOUT; +-} +- + static struct tsens_features tsens_8960_feat = { + .ver_major = VER_0, + .crit_int = 0, +@@ -315,7 +289,7 @@ static const struct reg_field tsens_8960 + static const struct tsens_ops ops_8960 = { + .init = init_common, + .calibrate = calibrate_8960, +- .get_temp = get_temp_8960, ++ .get_temp = get_temp_common, + .enable = enable_8960, + .disable = disable_8960, + .suspend = suspend_8960, diff --git a/target/linux/ipq806x/patches-5.15/104-7-drivers-thermal-tsens-Drop-unused-define-for-msm8960.patch b/target/linux/ipq806x/patches-5.15/104-7-drivers-thermal-tsens-Drop-unused-define-for-msm8960.patch new file mode 100644 index 0000000000..77ca3cfe45 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/104-7-drivers-thermal-tsens-Drop-unused-define-for-msm8960.patch @@ -0,0 +1,65 @@ +From 5716a61239c6ac9ceb137e825e93c3aea06c4634 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 19 Mar 2021 00:48:23 +0100 +Subject: [PATCH 07/10] drivers: thermal: tsens: Drop unused define for msm8960 + +Drop unused define for msm8960 replaced by generic api and reg_field. + +Signed-off-by: Ansuel Smith +Reviewed-by: Thara Gopinath +--- + drivers/thermal/qcom/tsens-8960.c | 24 +----------------------- + 1 file changed, 1 insertion(+), 23 deletions(-) + +--- a/drivers/thermal/qcom/tsens-8960.c ++++ b/drivers/thermal/qcom/tsens-8960.c +@@ -10,8 +10,6 @@ + #include + #include "tsens.h" + +-#define CAL_MDEGC 30000 +- + #define CONFIG_ADDR 0x3640 + #define CONFIG_ADDR_8660 0x3620 + /* CONFIG_ADDR bitmasks */ +@@ -21,39 +19,19 @@ + #define CONFIG_SHIFT_8660 28 + #define CONFIG_MASK_8660 (3 << CONFIG_SHIFT_8660) + +-#define STATUS_CNTL_ADDR_8064 0x3660 + #define CNTL_ADDR 0x3620 + /* CNTL_ADDR bitmasks */ + #define EN BIT(0) + #define SW_RST BIT(1) +-#define SENSOR0_EN BIT(3) ++ + #define MEASURE_PERIOD BIT(18) + #define SLP_CLK_ENA BIT(26) + #define SLP_CLK_ENA_8660 BIT(24) + #define SENSOR0_SHIFT 3 + +-/* INT_STATUS_ADDR bitmasks */ +-#define MIN_STATUS_MASK BIT(0) +-#define LOWER_STATUS_CLR BIT(1) +-#define UPPER_STATUS_CLR BIT(2) +-#define MAX_STATUS_MASK BIT(3) +- + #define THRESHOLD_ADDR 0x3624 +-/* THRESHOLD_ADDR bitmasks */ +-#define THRESHOLD_MAX_LIMIT_SHIFT 24 +-#define THRESHOLD_MIN_LIMIT_SHIFT 16 +-#define THRESHOLD_UPPER_LIMIT_SHIFT 8 +-#define THRESHOLD_LOWER_LIMIT_SHIFT 0 +- +-/* Initial temperature threshold values */ +-#define LOWER_LIMIT_TH 0x50 +-#define UPPER_LIMIT_TH 0xdf +-#define MIN_LIMIT_TH 0x0 +-#define MAX_LIMIT_TH 0xff + + #define INT_STATUS_ADDR 0x363c +-#define TRDY_MASK BIT(7) +-#define TIMEOUT_US 100 + + #define S0_STATUS_OFF 0x3628 + #define S1_STATUS_OFF 0x362c diff --git a/target/linux/ipq806x/patches-5.15/104-8-drivers-thermal-tsens-Add-support-for-ipq8064-tsens.patch b/target/linux/ipq806x/patches-5.15/104-8-drivers-thermal-tsens-Add-support-for-ipq8064-tsens.patch new file mode 100644 index 0000000000..127abaefc3 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/104-8-drivers-thermal-tsens-Add-support-for-ipq8064-tsens.patch @@ -0,0 +1,26 @@ +From 0d0c22a59bf2672b57e23da9a9ea743e91b71f54 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Sat, 25 Jul 2020 19:55:57 +0200 +Subject: [PATCH 08/10] drivers: thermal: tsens: Add support for ipq8064-tsens + +Add support for tsens present in ipq806x SoCs based on generic msm8960 +tsens driver. + +Signed-off-by: Ansuel Smith +Reviewed-by: Thara Gopinath +--- + drivers/thermal/qcom/tsens.c | 3 +++ + 1 file changed, 3 insertions(+) + +--- a/drivers/thermal/qcom/tsens.c ++++ b/drivers/thermal/qcom/tsens.c +@@ -968,6 +968,9 @@ static SIMPLE_DEV_PM_OPS(tsens_pm_ops, t + + static const struct of_device_id tsens_table[] = { + { ++ .compatible = "qcom,ipq8064-tsens", ++ .data = &data_8960, ++ }, { + .compatible = "qcom,msm8916-tsens", + .data = &data_8916, + }, { diff --git a/target/linux/ipq806x/patches-5.15/104-9-dt-bindings-thermal-tsens-Document-ipq8064-bindings.patch b/target/linux/ipq806x/patches-5.15/104-9-dt-bindings-thermal-tsens-Document-ipq8064-bindings.patch new file mode 100644 index 0000000000..382106863f --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/104-9-dt-bindings-thermal-tsens-Document-ipq8064-bindings.patch @@ -0,0 +1,112 @@ +From ac369071920d427dd484cf74cddba2774bba45f5 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Thu, 9 Jul 2020 22:35:54 +0200 +Subject: [PATCH 09/10] dt-bindings: thermal: tsens: Document ipq8064 bindings + +Document the use of bindings used for msm8960 tsens based devices. +msm8960 use the same gcc regs and is set as a child of the qcom gcc. + +Signed-off-by: Ansuel Smith +Reviewed-by: Rob Herring +--- + .../bindings/thermal/qcom-tsens.yaml | 56 ++++++++++++++++--- + 1 file changed, 48 insertions(+), 8 deletions(-) + +--- a/Documentation/devicetree/bindings/thermal/qcom-tsens.yaml ++++ b/Documentation/devicetree/bindings/thermal/qcom-tsens.yaml +@@ -19,6 +19,11 @@ description: | + properties: + compatible: + oneOf: ++ - description: msm9860 TSENS based ++ items: ++ - enum: ++ - qcom,ipq8064-tsens ++ + - description: v0.1 of TSENS + items: + - enum: +@@ -73,7 +78,9 @@ properties: + maxItems: 2 + items: + - const: calib +- - const: calib_sel ++ - enum: ++ - calib_backup ++ - calib_sel + + "#qcom,sensors": + description: +@@ -88,12 +95,20 @@ properties: + Number of cells required to uniquely identify the thermal sensors. Since + we have multiple sensors this is set to 1 + ++required: ++ - compatible ++ - interrupts ++ - interrupt-names ++ - "#thermal-sensor-cells" ++ - "#qcom,sensors" ++ + allOf: + - if: + properties: + compatible: + contains: + enum: ++ - qcom,ipq8064-tsens + - qcom,msm8916-tsens + - qcom,msm8974-tsens + - qcom,msm8976-tsens +@@ -114,19 +129,44 @@ allOf: + interrupt-names: + minItems: 2 + +-required: +- - compatible +- - reg +- - "#qcom,sensors" +- - interrupts +- - interrupt-names +- - "#thermal-sensor-cells" ++ - if: ++ properties: ++ compatible: ++ contains: ++ enum: ++ - qcom,tsens-v0_1 ++ - qcom,tsens-v1 ++ - qcom,tsens-v2 ++ ++ then: ++ required: ++ - reg + + additionalProperties: false + + examples: + - | + #include ++ // Example msm9860 based SoC (ipq8064): ++ gcc: clock-controller { ++ ++ /* ... */ ++ ++ tsens: thermal-sensor { ++ compatible = "qcom,ipq8064-tsens"; ++ ++ nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>; ++ nvmem-cell-names = "calib", "calib_backup"; ++ interrupts = ; ++ interrupt-names = "uplow"; ++ ++ #qcom,sensors = <11>; ++ #thermal-sensor-cells = <1>; ++ }; ++ }; ++ ++ - | ++ #include + // Example 1 (legacy: for pre v1 IP): + tsens1: thermal-sensor@900000 { + compatible = "qcom,msm8916-tsens", "qcom,tsens-v0_1"; diff --git a/target/linux/ipq806x/patches-5.15/105-10-drivers-thermal-tsens-Fix-wrong-slope-on-msm-8960.patch b/target/linux/ipq806x/patches-5.15/105-10-drivers-thermal-tsens-Fix-wrong-slope-on-msm-8960.patch new file mode 100644 index 0000000000..6cdc0b263f --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/105-10-drivers-thermal-tsens-Fix-wrong-slope-on-msm-8960.patch @@ -0,0 +1,32 @@ +From 68e720ed73c8f038c8c500e4c49c1e65a993a448 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Tue, 6 Apr 2021 04:45:31 +0200 +Subject: [PATCH 10/10] drivers: thermal: tsens: Fix wrong slope on msm-8960 + +Some user using some stats with the old legacy implementation and the +new implementation using the compute_intercept_slope reported an offset +of 3C. Fix the slope table to reflect the original temp. + +Signed-off-by: Ansuel Smith +--- + drivers/thermal/qcom/tsens-8960.c | 8 ++++---- + 1 file changed, 4 insertions(+), 4 deletions(-) + +--- a/drivers/thermal/qcom/tsens-8960.c ++++ b/drivers/thermal/qcom/tsens-8960.c +@@ -45,11 +45,11 @@ + #define S9_STATUS_OFF 0x3674 + #define S10_STATUS_OFF 0x3678 + +-/* Original slope - 200 to compensate mC to C inaccuracy */ ++/* Original slope - 350 to compensate mC to C inaccuracy */ + static u32 tsens_msm8960_slope[] = { +- 976, 976, 954, 976, +- 911, 932, 932, 999, +- 932, 999, 932 ++ 826, 826, 804, 826, ++ 761, 782, 782, 849, ++ 782, 849, 782 + }; + + static int suspend_8960(struct tsens_priv *priv) diff --git a/target/linux/ipq806x/patches-5.15/107-1-thermal-qcom-tsens-init-debugfs-only-with-successful.patch b/target/linux/ipq806x/patches-5.15/107-1-thermal-qcom-tsens-init-debugfs-only-with-successful.patch new file mode 100644 index 0000000000..1dc2d2e55e --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/107-1-thermal-qcom-tsens-init-debugfs-only-with-successful.patch @@ -0,0 +1,41 @@ +From 8f32d48a309246a80bdca505968085a484d54408 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Mon, 19 Apr 2021 03:01:53 +0200 +Subject: [thermal-next PATCH v2 1/2] thermal: qcom: tsens: init debugfs only with + successful probe + +calibrate and tsens_register can fail or PROBE_DEFER. This will cause a +double or a wrong init of the debugfs information. Init debugfs only +with successful probe fixing warning about directory already present. + +Signed-off-by: Ansuel Smith +Acked-by: Thara Gopinath +--- + drivers/thermal/qcom/tsens.c | 9 ++++++--- + 1 file changed, 6 insertions(+), 3 deletions(-) + +--- a/drivers/thermal/qcom/tsens.c ++++ b/drivers/thermal/qcom/tsens.c +@@ -918,8 +918,6 @@ int __init init_common(struct tsens_priv + if (tsens_version(priv) >= VER_0_1) + tsens_enable_irq(priv); + +- tsens_debug_init(op); +- + err_put_device: + put_device(&op->dev); + return ret; +@@ -1155,7 +1153,12 @@ static int tsens_probe(struct platform_d + } + } + +- return tsens_register(priv); ++ ret = tsens_register(priv); ++ ++ if (!ret) ++ tsens_debug_init(pdev); ++ ++ return ret; + } + + static int tsens_remove(struct platform_device *pdev) diff --git a/target/linux/ipq806x/patches-5.15/107-2-thermal-qcom-tsens-simplify-debugfs-init-function.patch b/target/linux/ipq806x/patches-5.15/107-2-thermal-qcom-tsens-simplify-debugfs-init-function.patch new file mode 100644 index 0000000000..0fbc4bd8ca --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/107-2-thermal-qcom-tsens-simplify-debugfs-init-function.patch @@ -0,0 +1,54 @@ +From 4204f22060f7a5d42c6ccb4d4c25a6a875571099 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Mon, 19 Apr 2021 03:08:37 +0200 +Subject: [thermal-next PATCH v2 2/2] thermal: qcom: tsens: simplify debugfs init + function + +Simplify debugfs init function. +- Add check for existing dev directory. +- Fix wrong version in dbg_version_show (with version 0.0.0, 0.1.0 was + incorrectly reported) + +Signed-off-by: Ansuel Smith +Reviewed-by: Thara Gopinath +--- + drivers/thermal/qcom/tsens.c | 16 +++++++--------- + 1 file changed, 7 insertions(+), 9 deletions(-) + +--- a/drivers/thermal/qcom/tsens.c ++++ b/drivers/thermal/qcom/tsens.c +@@ -692,7 +692,7 @@ static int dbg_version_show(struct seq_f + return ret; + seq_printf(s, "%d.%d.%d\n", maj_ver, min_ver, step_ver); + } else { +- seq_puts(s, "0.1.0\n"); ++ seq_printf(s, "0.%d.0\n", priv->feat->ver_major); + } + + return 0; +@@ -704,21 +704,17 @@ DEFINE_SHOW_ATTRIBUTE(dbg_sensors); + static void tsens_debug_init(struct platform_device *pdev) + { + struct tsens_priv *priv = platform_get_drvdata(pdev); +- struct dentry *root, *file; + +- root = debugfs_lookup("tsens", NULL); +- if (!root) ++ priv->debug_root = debugfs_lookup("tsens", NULL); ++ if (!priv->debug_root) + priv->debug_root = debugfs_create_dir("tsens", NULL); +- else +- priv->debug_root = root; + +- file = debugfs_lookup("version", priv->debug_root); +- if (!file) ++ if (!debugfs_lookup("version", priv->debug_root)) + debugfs_create_file("version", 0444, priv->debug_root, + pdev, &dbg_version_fops); + + /* A directory for each instance of the TSENS IP */ +- priv->debug = debugfs_create_dir(dev_name(&pdev->dev), priv->debug_root); ++ priv->debug = debugfs_lookup(dev_name(&pdev->dev), priv->debug_root); + debugfs_create_file("sensors", 0444, priv->debug, pdev, &dbg_sensors_fops); + } + #else diff --git a/target/linux/ipq806x/patches-5.15/108-v5.14-net-stmmac-explicitly-deassert-gmac-ahb-reset.patch b/target/linux/ipq806x/patches-5.15/108-v5.14-net-stmmac-explicitly-deassert-gmac-ahb-reset.patch new file mode 100644 index 0000000000..dd1e506e5b --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/108-v5.14-net-stmmac-explicitly-deassert-gmac-ahb-reset.patch @@ -0,0 +1,75 @@ +From e67f325e9cd67562b761e884680c0fec03a6f404 Mon Sep 17 00:00:00 2001 +From: Matthew Hagan +Date: Tue, 8 Jun 2021 19:59:06 +0100 +Subject: net: stmmac: explicitly deassert GMAC_AHB_RESET + +We are currently assuming that GMAC_AHB_RESET will already be deasserted +by the bootloader. However if this has not been done, probing of the GMAC +will fail. To remedy this we must ensure GMAC_AHB_RESET has been deasserted +prior to probing. + +v2 changes: + - remove NULL condition check for stmmac_ahb_rst in stmmac_main.c + - unwrap dev_err() message in stmmac_main.c + - add PTR_ERR() around plat->stmmac_ahb_rst in stmmac_platform.c + +v3 changes: + - add error pointer to dev_err() output + - add reset_control_assert(stmmac_ahb_rst) in stmmac_dvr_remove + - revert PTR_ERR() around plat->stmmac_ahb_rst since this is performed + on the returned value of ret by the calling function + +Signed-off-by: Matthew Hagan +Signed-off-by: David S. Miller +--- + drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 5 +++++ + drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c | 6 ++++++ + include/linux/stmmac.h | 1 + + 3 files changed, 12 insertions(+) + +--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c ++++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +@@ -5021,6 +5021,10 @@ int stmmac_dvr_probe(struct device *devi + reset_control_reset(priv->plat->stmmac_rst); + } + ++ ret = reset_control_deassert(priv->plat->stmmac_ahb_rst); ++ if (ret == -ENOTSUPP) ++ dev_err(priv->device, "unable to bring out of ahb reset\n"); ++ + /* Init MAC and get the capabilities */ + ret = stmmac_hw_init(priv); + if (ret) +@@ -5245,6 +5249,7 @@ int stmmac_dvr_remove(struct device *dev + phylink_destroy(priv->phylink); + if (priv->plat->stmmac_rst) + reset_control_assert(priv->plat->stmmac_rst); ++ reset_control_assert(priv->plat->stmmac_ahb_rst); + pm_runtime_put(dev); + pm_runtime_disable(dev); + if (priv->hw->pcs != STMMAC_PCS_TBI && +--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c ++++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c +@@ -617,6 +617,12 @@ stmmac_probe_config_dt(struct platform_d + plat->stmmac_rst = NULL; + } + ++ plat->stmmac_ahb_rst = devm_reset_control_get_optional_shared( ++ &pdev->dev, "ahb"); ++ if (IS_ERR(plat->stmmac_ahb_rst)) ++ if (PTR_ERR(plat->stmmac_ahb_rst) == -EPROBE_DEFER) ++ goto error_hw_init; ++ + return plat; + + error_hw_init: +--- a/include/linux/stmmac.h ++++ b/include/linux/stmmac.h +@@ -192,6 +192,7 @@ struct plat_stmmacenet_data { + unsigned int clk_ref_rate; + s32 ptp_max_adj; + struct reset_control *stmmac_rst; ++ struct reset_control *stmmac_ahb_rst; + struct stmmac_axi *axi; + int has_gmac4; + bool has_sun8i; diff --git a/target/linux/ipq806x/patches-5.15/109-v5.15-arm-dts-qcom-add-ahb-reset-to-ipq806x-gmac.patch b/target/linux/ipq806x/patches-5.15/109-v5.15-arm-dts-qcom-add-ahb-reset-to-ipq806x-gmac.patch new file mode 100644 index 0000000000..4a047ed6eb --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/109-v5.15-arm-dts-qcom-add-ahb-reset-to-ipq806x-gmac.patch @@ -0,0 +1,64 @@ +From f95c4c56d65225a537a2d88735fde7ec4d37641d Mon Sep 17 00:00:00 2001 +From: Matthew Hagan +Date: Sat, 5 Jun 2021 18:35:38 +0100 +Subject: ARM: dts: qcom: add ahb reset to ipq806x-gmac + +Add GMAC_AHB_RESET to the resets property of each gmac node. + +Signed-off-by: Matthew Hagan +Link: https://lore.kernel.org/r/20210605173546.4102455-2-mnhagan88@gmail.com +Signed-off-by: Bjorn Andersson +--- + arch/arm/boot/dts/qcom-ipq8064.dtsi | 20 ++++++++++++-------- + 1 file changed, 12 insertions(+), 8 deletions(-) + +--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi ++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi +@@ -1335,8 +1335,9 @@ + clocks = <&gcc GMAC_CORE1_CLK>; + clock-names = "stmmaceth"; + +- resets = <&gcc GMAC_CORE1_RESET>; +- reset-names = "stmmaceth"; ++ resets = <&gcc GMAC_CORE1_RESET>, ++ <&gcc GMAC_AHB_RESET>; ++ reset-names = "stmmaceth", "ahb"; + + status = "disabled"; + }; +@@ -1358,8 +1359,9 @@ + clocks = <&gcc GMAC_CORE2_CLK>; + clock-names = "stmmaceth"; + +- resets = <&gcc GMAC_CORE2_RESET>; +- reset-names = "stmmaceth"; ++ resets = <&gcc GMAC_CORE2_RESET>, ++ <&gcc GMAC_AHB_RESET>; ++ reset-names = "stmmaceth", "ahb"; + + status = "disabled"; + }; +@@ -1381,8 +1383,9 @@ + clocks = <&gcc GMAC_CORE3_CLK>; + clock-names = "stmmaceth"; + +- resets = <&gcc GMAC_CORE3_RESET>; +- reset-names = "stmmaceth"; ++ resets = <&gcc GMAC_CORE3_RESET>, ++ <&gcc GMAC_AHB_RESET>; ++ reset-names = "stmmaceth", "ahb"; + + status = "disabled"; + }; +@@ -1404,8 +1407,9 @@ + clocks = <&gcc GMAC_CORE4_CLK>; + clock-names = "stmmaceth"; + +- resets = <&gcc GMAC_CORE4_RESET>; +- reset-names = "stmmaceth"; ++ resets = <&gcc GMAC_CORE4_RESET>, ++ <&gcc GMAC_AHB_RESET>; ++ reset-names = "stmmaceth", "ahb"; + + status = "disabled"; + }; diff --git a/target/linux/ipq806x/patches-5.15/850-soc-add-qualcomm-syscon.patch b/target/linux/ipq806x/patches-5.15/850-soc-add-qualcomm-syscon.patch new file mode 100644 index 0000000000..8325e10389 --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/850-soc-add-qualcomm-syscon.patch @@ -0,0 +1,121 @@ +From: Christian Lamparter +Subject: SoC: add qualcomm syscon +--- a/drivers/soc/qcom/Makefile ++++ b/drivers/soc/qcom/Makefile +@@ -21,6 +21,7 @@ obj-$(CONFIG_QCOM_SMP2P) += smp2p.o + obj-$(CONFIG_QCOM_SMSM) += smsm.o + obj-$(CONFIG_QCOM_SOCINFO) += socinfo.o + obj-$(CONFIG_QCOM_WCNSS_CTRL) += wcnss_ctrl.o ++obj-$(CONFIG_QCOM_TCSR) += qcom_tcsr.o + obj-$(CONFIG_QCOM_APR) += apr.o + obj-$(CONFIG_QCOM_LLCC) += llcc-qcom.o + obj-$(CONFIG_QCOM_RPMHPD) += rpmhpd.o +--- a/drivers/soc/qcom/Kconfig ++++ b/drivers/soc/qcom/Kconfig +@@ -189,6 +189,13 @@ config QCOM_SOCINFO + Say yes here to support the Qualcomm socinfo driver, providing + information about the SoC to user space. + ++config QCOM_TCSR ++ tristate "QCOM Top Control and Status Registers" ++ depends on ARCH_QCOM ++ help ++ Say y here to enable TCSR support. The TCSR provides control ++ functions for various peripherals. ++ + config QCOM_WCNSS_CTRL + tristate "Qualcomm WCNSS control driver" + depends on ARCH_QCOM || COMPILE_TEST +--- /dev/null ++++ b/drivers/soc/qcom/qcom_tcsr.c +@@ -0,0 +1,64 @@ ++/* ++ * Copyright (c) 2014, The Linux foundation. All rights reserved. ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License rev 2 and ++ * only rev 2 as published by the free Software foundation. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or fITNESS fOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define TCSR_USB_PORT_SEL 0xb0 ++ ++static int tcsr_probe(struct platform_device *pdev) ++{ ++ struct resource *res; ++ const struct device_node *node = pdev->dev.of_node; ++ void __iomem *base; ++ u32 val; ++ ++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ base = devm_ioremap_resource(&pdev->dev, res); ++ if (IS_ERR(base)) ++ return PTR_ERR(base); ++ ++ if (!of_property_read_u32(node, "qcom,usb-ctrl-select", &val)) { ++ dev_err(&pdev->dev, "setting usb port select = %d\n", val); ++ writel(val, base + TCSR_USB_PORT_SEL); ++ } ++ ++ return 0; ++} ++ ++static const struct of_device_id tcsr_dt_match[] = { ++ { .compatible = "qcom,tcsr", }, ++ { }, ++}; ++ ++MODULE_DEVICE_TABLE(of, tcsr_dt_match); ++ ++static struct platform_driver tcsr_driver = { ++ .driver = { ++ .name = "tcsr", ++ .owner = THIS_MODULE, ++ .of_match_table = tcsr_dt_match, ++ }, ++ .probe = tcsr_probe, ++}; ++ ++module_platform_driver(tcsr_driver); ++ ++MODULE_AUTHOR("Andy Gross "); ++MODULE_DESCRIPTION("QCOM TCSR driver"); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/include/dt-bindings/soc/qcom,tcsr.h +@@ -0,0 +1,23 @@ ++/* Copyright (c) 2014, The Linux Foundation. All rights reserved. ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 and ++ * only version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ */ ++#ifndef __DT_BINDINGS_QCOM_TCSR_H ++#define __DT_BINDINGS_QCOM_TCSR_H ++ ++#define TCSR_USB_SELECT_USB3_P0 0x1 ++#define TCSR_USB_SELECT_USB3_P1 0x2 ++#define TCSR_USB_SELECT_USB3_DUAL 0x3 ++ ++/* TCSR A/B REG */ ++#define IPQ806X_TCSR_REG_A_ADM_CRCI_MUX_SEL 0 ++#define IPQ806X_TCSR_REG_B_ADM_CRCI_MUX_SEL 1 ++ ++#endif diff --git a/target/linux/ipq806x/patches-5.15/900-arm-add-cmdline-override.patch b/target/linux/ipq806x/patches-5.15/900-arm-add-cmdline-override.patch new file mode 100644 index 0000000000..dba917872c --- /dev/null +++ b/target/linux/ipq806x/patches-5.15/900-arm-add-cmdline-override.patch @@ -0,0 +1,37 @@ +--- a/arch/arm/Kconfig ++++ b/arch/arm/Kconfig +@@ -1794,6 +1794,14 @@ config ARM_ATAG_DTB_COMPAT_CMDLINE_MANGL + + endchoice + ++config CMDLINE_OVERRIDE ++ bool "Use alternative cmdline from device tree" ++ help ++ Some bootloaders may have uneditable bootargs. While CMDLINE_FORCE can ++ be used, this is not a good option for kernels that are shared across ++ devices. This setting enables using "chosen/cmdline-override" as the ++ cmdline if it exists in the device tree. ++ + config CMDLINE + string "Default kernel command string" + default "" +--- a/drivers/of/fdt.c ++++ b/drivers/of/fdt.c +@@ -1059,6 +1059,17 @@ int __init early_init_dt_scan_chosen(uns + if (p != NULL && l > 0) + strlcat(data, p, min_t(int, strlen(data) + (int)l, COMMAND_LINE_SIZE)); + ++ /* CONFIG_CMDLINE_OVERRIDE is used to fallback to a different ++ * device tree option of chosen/bootargs-override. This is ++ * helpful on boards where u-boot sets bootargs, and is unable ++ * to be modified. ++ */ ++#ifdef CONFIG_CMDLINE_OVERRIDE ++ p = of_get_flat_dt_prop(node, "bootargs-override", &l); ++ if (p != NULL && l > 0) ++ strlcpy(data, p, min((int)l, COMMAND_LINE_SIZE)); ++#endif ++ + /* + * CONFIG_CMDLINE is meant to be a default in case nothing else + * managed to set the command line, unless CONFIG_CMDLINE_FORCE