From: WonJung Kim Date: Wed, 22 Dec 2021 06:59:00 +0000 (+0900) Subject: ramips: add support for ipTIME A3004T X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=2dde2416e1a2f7a3208095e29c20132ed9910889;p=openwrt%2Fstaging%2Flynxis.git ramips: add support for ipTIME A3004T ipTIME A3004T is a 2.4/5GHz band router, based on Mediatek MT7621. Specifications: - SoC: MT7621 (880MHz) - RAM: DDR3 256M - Flash: NAND 128MB (Macronix NAND 128MiB 3,3V 8-bit) - WiFi: - 2.4GHz: MT7615E - 5GHz : MT7615E - Ethernet: - 4x LAN - 1x WAN - USB: 1 * USB3.0 port - UART: - 3.3V, TX, RX, GND / 57600 8N1 Installation via web interface: 1. Flash initramfs image using OEM's Recovery mode 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: - Flash stock firmware via OEM's Recovery mode How to use OEM's Recovery mode: 1. Power up with holding down the reset key until CPU LED stop blinking. 2. Set fixed ip with `192.168.0.2` with subnet mask `255.255.255.0` 3. Flash image via tftp to `192.168.0.1` Additional Notes: This router shares one MT7915E chip for both 2.4Ghz/5Ghz. radio0 will not working on 5Ghz as it's not connected to the antenna. Signed-off-by: WonJung Kim (added led dt-bindings) Signed-off-by: Christian Lamparter --- diff --git a/target/linux/ramips/dts/mt7621_iptime_a3004t.dts b/target/linux/ramips/dts/mt7621_iptime_a3004t.dts new file mode 100644 index 0000000000..704ecac721 --- /dev/null +++ b/target/linux/ramips/dts/mt7621_iptime_a3004t.dts @@ -0,0 +1,172 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7621.dtsi" + +#include +#include +#include + +/ { + compatible = "iptime,a3004t", "mediatek,mt7621-soc"; + model = "ipTIME A3004T"; + + aliases { + led-boot = &led_cpu; + led-failsafe = &led_cpu; + led-running = &led_cpu; + led-upgrade = &led_cpu; + }; + + leds { + compatible = "gpio-leds"; + + led_cpu: led-0 { + label = "amber:cpu"; + color = ; + function = LED_FUNCTION_CPU; + gpios = <&gpio 18 GPIO_ACTIVE_LOW>; + }; + + led-1 { + color = ; + function = LED_FUNCTION_WLAN; + function-enumerator = <0>; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0radio"; + }; + + led-2 { + color = ; + function = LED_FUNCTION_WLAN; + function-enumerator = <1>; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1radio"; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; +}; + +&nand { + status = "okay"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x80000>; + read-only; + }; + + partition@80000 { + label = "config"; + reg = <0x80000 0x20000>; + read-only; + }; + + factory: partition@a0000 { + label = "factory"; + reg = <0xa0000 0x20000>; + read-only; + + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_factory_4: macaddr@4 { + reg = <0x4 0x6>; + }; + + macaddr_factory_8004: macaddr@8004 { + reg = <0x8004 0x6>; + }; + }; + + partition@140000 { + label = "firmware"; + reg = <0x140000 0x7e40000>; + + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "kernel"; + reg = <0x0 0x400000>; + }; + + partition@400000 { + label = "ubi"; + reg = <0x400000 0x7a40000>; + }; + }; + }; +}; + +&gmac0 { + nvmem-cells = <&macaddr_factory_4>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <(3)>; +}; + +&switch0 { + ports { + port@0 { + status = "okay"; + label = "wan"; + nvmem-cells = <&macaddr_factory_4>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <(1)>; + }; + + port@1 { + status = "okay"; + label = "lan4"; + }; + + port@2 { + status = "okay"; + label = "lan3"; + }; + + port@3 { + status = "okay"; + label = "lan2"; + }; + + port@4 { + status = "okay"; + label = "lan1"; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pcie0 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x0>; + }; +}; + +&state_default { + gpio { + groups = "i2c", "jtag", "wdt"; + function = "gpio"; + }; +}; diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index 35c5627264..e1cb0195b0 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -766,6 +766,23 @@ define Device/iptime_a3004ns-dual endef TARGET_DEVICES += iptime_a3004ns-dual +define Device/iptime_a3004t + $(Device/dsa-migration) + $(Device/uimage-lzma-loader) + BLOCKSIZE := 128k + PAGESIZE := 2048 + FILESYSTEMS := squashfs + KERNEL_SIZE := 4096k + IMAGE_SIZE := 129280k + UIMAGE_NAME := a3004t + UBINIZE_OPTS := -E 5 + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata + DEVICE_VENDOR := ipTIME + DEVICE_MODEL := A3004T + DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 +endef +TARGET_DEVICES += iptime_a3004t + define Device/iptime_a6ns-m $(Device/dsa-migration) IMAGE_SIZE := 16128k diff --git a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh index 6e8e205403..790de22f40 100755 --- a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh @@ -58,6 +58,7 @@ platform_do_upgrade() { dlink,dir-2660-a1|\ dlink,dir-853-a3|\ hiwifi,hc5962|\ + iptime,a3004t|\ jcg,q20|\ linksys,e5600|\ linksys,ea7300-v1|\