From: Masahiro Yamada Date: Tue, 17 Mar 2015 03:28:05 +0000 (+0900) Subject: powerpc: ppc4xx: remove JSE board support X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=2da8137b450304070364ec7bb3cf93034f0230c1;p=project%2Fbcm63xx%2Fu-boot.git powerpc: ppc4xx: remove JSE board support This has not been converted to Generic Board, so should be removed. (See doc/README.generic-board for details.) Signed-off-by: Masahiro Yamada Cc: Stephen Williams --- diff --git a/arch/powerpc/cpu/ppc4xx/Kconfig b/arch/powerpc/cpu/ppc4xx/Kconfig index 5db5e34627..e1512001f1 100644 --- a/arch/powerpc/cpu/ppc4xx/Kconfig +++ b/arch/powerpc/cpu/ppc4xx/Kconfig @@ -13,9 +13,6 @@ config TARGET_CSB272 config TARGET_CSB472 bool "Support csb472" -config TARGET_JSE - bool "Support JSE" - config TARGET_KORAT bool "Support korat" @@ -204,7 +201,6 @@ source "board/gdsys/405ex/Kconfig" source "board/gdsys/dlvision/Kconfig" source "board/gdsys/gdppc440etx/Kconfig" source "board/gdsys/intip/Kconfig" -source "board/jse/Kconfig" source "board/korat/Kconfig" source "board/lwmon5/Kconfig" source "board/mosaixtech/icon/Kconfig" diff --git a/board/jse/Kconfig b/board/jse/Kconfig deleted file mode 100644 index 48905fa76f..0000000000 --- a/board/jse/Kconfig +++ /dev/null @@ -1,9 +0,0 @@ -if TARGET_JSE - -config SYS_BOARD - default "jse" - -config SYS_CONFIG_NAME - default "JSE" - -endif diff --git a/board/jse/MAINTAINERS b/board/jse/MAINTAINERS deleted file mode 100644 index 818a5a0be4..0000000000 --- a/board/jse/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -JSE BOARD -M: Stephen Williams -S: Maintained -F: board/jse/ -F: include/configs/JSE.h -F: configs/JSE_defconfig diff --git a/board/jse/Makefile b/board/jse/Makefile deleted file mode 100644 index feac3a8834..0000000000 --- a/board/jse/Makefile +++ /dev/null @@ -1,12 +0,0 @@ -# -# (C) Copyright 2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# Copyright 2004 Picture Elements, Inc. -# Stephen Williams -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y = jse.o sdram.o flash.o host_bridge.o -obj-y += init.o diff --git a/board/jse/README.txt b/board/jse/README.txt deleted file mode 100644 index 84497db70f..0000000000 --- a/board/jse/README.txt +++ /dev/null @@ -1,48 +0,0 @@ -JSE Configuration Details - -Memory Bank 0 -- Flash chip ---------------------------- - -0xfff00000 - 0xffffffff - -The flash chip is really only 512Kbytes, but the high address bit of -the 1Meg region is ignored, so the flash is replicated through the -region. Thus, this is consistent with a flash base address 0xfff80000. - -The placement at the end is to be consistent with reset behavior, -where the processor itself initially uses this bus to load the branch -vector and start running. - -On-Chip Memory --------------- - -0xf4000000 - 0xf4000fff - -The 405GPr includes a 4K on-chip memory that can be placed however -software chooses. I choose to place the memory at this address, to -keep it out of the cachable areas. - - -Memory Bank 1 -- SystemACE Controller -------------------------------------- - -0xf0000000 - 0xf00fffff - -The SystemACE chip is along on peripheral bank CS#1. We don't need -much space, but 1Meg is the smallest we can configure the chip to -allocate. We need it far away from the flash region, because this -region is set to be non-cached. - - -Internal Peripherals --------------------- - -0xef600300 - 0xef6008ff - -These are scattered various peripherals internal to the PPC405GPr -chip. - -SDRAM ------ - -0x00000000 - 0x07ffffff (128 MBytes) diff --git a/board/jse/flash.c b/board/jse/flash.c deleted file mode 100644 index a550f7d03e..0000000000 --- a/board/jse/flash.c +++ /dev/null @@ -1,491 +0,0 @@ -/* - * (C) Copyright 2000-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * Modified 4/5/2001 - * Wait for completion of each sector erase command issued - * 4/5/2001 - * Chris Hallinan - DS4.COM, Inc. - clh@net1plus.com - */ - -#include -#include -#include - -#if CONFIG_SYS_MAX_FLASH_BANKS != 1 -#error "CONFIG_SYS_MAX_FLASH_BANKS must be 1" -#endif -flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */ - -/*----------------------------------------------------------------------- - * Functions - */ -static ulong flash_get_size (vu_long * addr, flash_info_t * info); -static int write_word (flash_info_t * info, ulong dest, ulong data); -static void flash_get_offsets (ulong base, flash_info_t * info); - -#define ADDR0 0x5555 -#define ADDR1 0x2aaa -#define FLASH_WORD_SIZE unsigned char - -/*----------------------------------------------------------------------- - */ - -unsigned long flash_init (void) -{ - unsigned long size_b0; - - /* Init: no FLASHes known */ - flash_info[0].flash_id = FLASH_UNKNOWN; - - /* Static FLASH Bank configuration here - FIXME XXX */ - - size_b0 = flash_get_size ((vu_long *) FLASH_BASE0_PRELIM, &flash_info[0]); - - if (flash_info[0].flash_id == FLASH_UNKNOWN) { - printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n", - size_b0, size_b0 << 20); - } - - /* Only one bank */ - /* Setup offsets */ - flash_get_offsets (FLASH_BASE0_PRELIM, &flash_info[0]); - - /* Monitor protection ON by default */ - (void) flash_protect (FLAG_PROTECT_SET, - FLASH_BASE0_PRELIM, - FLASH_BASE0_PRELIM + monitor_flash_len - 1, - &flash_info[0]); - flash_info[0].size = size_b0; - - return size_b0; -} - - -/*----------------------------------------------------------------------- - */ -/* - * This implementation assumes that the flash chips are uniform sector - * devices. This is true for all likely JSE devices. - */ -static void flash_get_offsets (ulong base, flash_info_t * info) -{ - unsigned idx; - unsigned long sector_size = info->size / info->sector_count; - - for (idx = 0; idx < info->sector_count; idx += 1) { - info->start[idx] = base + (idx * sector_size); - } -} - -/*----------------------------------------------------------------------- - */ -void flash_print_info (flash_info_t * info) -{ - int i; - int k; - int size; - int erased; - volatile unsigned long *flash; - - if (info->flash_id == FLASH_UNKNOWN) { - printf ("missing or unknown FLASH type\n"); - return; - } - - switch (info->flash_id & FLASH_VENDMASK) { - case FLASH_MAN_AMD: - printf ("AMD "); - break; - case FLASH_MAN_FUJ: - printf ("FUJITSU "); - break; - case FLASH_MAN_SST: - printf ("SST "); - break; - case FLASH_MAN_STM: - printf ("ST Micro "); - break; - default: - printf ("Unknown Vendor "); - break; - } - - /* (Reduced table of only parts expected in JSE boards.) */ - switch (info->flash_id) { - case FLASH_MAN_AMD | FLASH_AM040: - printf ("AM29F040 (512 Kbit, uniform sector size)\n"); - break; - case FLASH_MAN_STM | FLASH_AM040: - printf ("MM29W040W (512 Kbit, uniform sector size)\n"); - break; - default: - printf ("Unknown Chip Type\n"); - break; - } - - printf (" Size: %ld KB in %d Sectors\n", - info->size >> 10, info->sector_count); - - printf (" Sector Start Addresses:"); - for (i = 0; i < info->sector_count; ++i) { - /* - * Check if whole sector is erased - */ - if (i != (info->sector_count - 1)) - size = info->start[i + 1] - info->start[i]; - else - size = info->start[0] + info->size - info->start[i]; - erased = 1; - flash = (volatile unsigned long *) info->start[i]; - size = size >> 2; /* divide by 4 for longword access */ - for (k = 0; k < size; k++) { - if (*flash++ != 0xffffffff) { - erased = 0; - break; - } - } - - if ((i % 5) == 0) - printf ("\n "); - printf (" %08lX%s%s", - info->start[i], - erased ? " E" : " ", info->protect[i] ? "RO " : " " - ); - } - printf ("\n"); - return; -} - -/*----------------------------------------------------------------------- - */ - - -/*----------------------------------------------------------------------- - */ - -/* - * The following code cannot be run from FLASH! - */ -static ulong flash_get_size (vu_long * addr, flash_info_t * info) -{ - short i; - FLASH_WORD_SIZE value; - ulong base = (ulong) addr; - volatile FLASH_WORD_SIZE *addr2 = (FLASH_WORD_SIZE *) addr; - - /* Write auto select command: read Manufacturer ID */ - addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA; - addr2[ADDR1] = (FLASH_WORD_SIZE) 0x00550055; - addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00900090; - - value = addr2[0]; - - switch (value) { - case (FLASH_WORD_SIZE) AMD_MANUFACT: - info->flash_id = FLASH_MAN_AMD; - break; - case (FLASH_WORD_SIZE) FUJ_MANUFACT: - info->flash_id = FLASH_MAN_FUJ; - break; - case (FLASH_WORD_SIZE) SST_MANUFACT: - info->flash_id = FLASH_MAN_SST; - break; - case (FLASH_WORD_SIZE)STM_MANUFACT: - info->flash_id = FLASH_MAN_STM; - break; - default: - info->flash_id = FLASH_UNKNOWN; - info->sector_count = 0; - info->size = 0; - printf("Unknown flash manufacturer code: 0x%x\n", value); - return (0); /* no or unknown flash */ - } - - value = addr2[1]; /* device ID */ - - switch (value) { - case (FLASH_WORD_SIZE) AMD_ID_F040B: - info->flash_id += FLASH_AM040; - info->sector_count = 8; - info->size = 0x0080000; /* => 512 ko */ - break; - case (FLASH_WORD_SIZE) AMD_ID_LV040B: - info->flash_id += FLASH_AM040; - info->sector_count = 8; - info->size = 0x0080000; /* => 512 ko */ - break; - case (FLASH_WORD_SIZE)STM_ID_M29W040B: /* most likele JSE chip */ - info->flash_id += FLASH_AM040; - info->sector_count = 8; - info->size = 0x0080000; /* => 512 ko */ - break; - default: - info->flash_id = FLASH_UNKNOWN; - return (0); /* => no or unknown flash */ - - } - - /* Calculate the sector offsets (Use JSE Optimized code). */ - flash_get_offsets(base, info); - - /* check for protected sectors */ - for (i = 0; i < info->sector_count; i++) { - /* read sector protection at sector address, (A7 .. A0) = 0x02 */ - /* D0 = 1 if protected */ - addr2 = (volatile FLASH_WORD_SIZE *) (info->start[i]); - if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) - info->protect[i] = 0; - else - info->protect[i] = addr2[2] & 1; - } - - /* - * Prevent writes to uninitialized FLASH. - */ - if (info->flash_id != FLASH_UNKNOWN) { - addr2 = (FLASH_WORD_SIZE *) info->start[0]; - *addr2 = (FLASH_WORD_SIZE) 0x00F000F0; /* reset bank */ - } - - return (info->size); -} - -int wait_for_DQ7 (flash_info_t * info, int sect) -{ - ulong start, now, last; - volatile FLASH_WORD_SIZE *addr = - (FLASH_WORD_SIZE *) (info->start[sect]); - - start = get_timer (0); - last = start; - while ((addr[0] & (FLASH_WORD_SIZE) 0x00800080) != - (FLASH_WORD_SIZE) 0x00800080) { - if ((now = get_timer (start)) > CONFIG_SYS_FLASH_ERASE_TOUT) { - printf ("Timeout\n"); - return -1; - } - /* show that we're waiting */ - if ((now - last) > 1000) { /* every second */ - putc ('.'); - last = now; - } - } - return 0; -} - -/*----------------------------------------------------------------------- - */ - -int flash_erase (flash_info_t * info, int s_first, int s_last) -{ - volatile FLASH_WORD_SIZE *addr = (FLASH_WORD_SIZE *) (info->start[0]); - volatile FLASH_WORD_SIZE *addr2; - int flag, prot, sect; - int i; - - if ((s_first < 0) || (s_first > s_last)) { - if (info->flash_id == FLASH_UNKNOWN) { - printf ("- missing\n"); - } else { - printf ("- no sectors to erase\n"); - } - return 1; - } - - if (info->flash_id == FLASH_UNKNOWN) { - printf ("Can't erase unknown flash type - aborted\n"); - return 1; - } - - prot = 0; - for (sect = s_first; sect <= s_last; ++sect) { - if (info->protect[sect]) { - prot++; - } - } - - if (prot) { - printf ("- Warning: %d protected sectors will not be erased!\n", prot); - } else { - printf ("\n"); - } - - /* Disable interrupts which might cause a timeout here */ - flag = disable_interrupts (); - - /* Start erase on unprotected sectors */ - for (sect = s_first; sect <= s_last; sect++) { - if (info->protect[sect] == 0) { /* not protected */ - addr2 = (FLASH_WORD_SIZE *) (info->start[sect]); - printf ("Erasing sector %p\n", addr2); /* CLH */ - - if ((info->flash_id & FLASH_VENDMASK) == - FLASH_MAN_SST) { - addr[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA; - addr[ADDR1] = (FLASH_WORD_SIZE) 0x00550055; - addr[ADDR0] = (FLASH_WORD_SIZE) 0x00800080; - addr[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA; - addr[ADDR1] = (FLASH_WORD_SIZE) 0x00550055; - addr2[0] = (FLASH_WORD_SIZE) 0x00500050; /* block erase */ - for (i = 0; i < 50; i++) - udelay (1000); /* wait 1 ms */ - } else { - addr[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA; - addr[ADDR1] = (FLASH_WORD_SIZE) 0x00550055; - addr[ADDR0] = (FLASH_WORD_SIZE) 0x00800080; - addr[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA; - addr[ADDR1] = (FLASH_WORD_SIZE) 0x00550055; - addr2[0] = (FLASH_WORD_SIZE) 0x00300030; /* sector erase */ - } - /* - * Wait for each sector to complete, it's more - * reliable. According to AMD Spec, you must - * issue all erase commands within a specified - * timeout. This has been seen to fail, especially - * if printf()s are included (for debug)!! - */ - wait_for_DQ7 (info, sect); - } - } - - /* re-enable interrupts if necessary */ - if (flag) - enable_interrupts (); - - /* wait at least 80us - let's wait 1 ms */ - udelay (1000); - - /* reset to read mode */ - addr = (FLASH_WORD_SIZE *) info->start[0]; - addr[0] = (FLASH_WORD_SIZE) 0x00F000F0; /* reset bank */ - - printf (" done\n"); - return 0; -} - -/*----------------------------------------------------------------------- - * Copy memory to flash, returns: - * 0 - OK - * 1 - write timeout - * 2 - Flash not erased - */ - -int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt) -{ - ulong cp, wp, data; - int i, l, rc; - - wp = (addr & ~3); /* get lower word aligned address */ - - /* - * handle unaligned start bytes - */ - if ((l = addr - wp) != 0) { - data = 0; - for (i = 0, cp = wp; i < l; ++i, ++cp) { - data = (data << 8) | (*(uchar *) cp); - } - for (; i < 4 && cnt > 0; ++i) { - data = (data << 8) | *src++; - --cnt; - ++cp; - } - for (; cnt == 0 && i < 4; ++i, ++cp) { - data = (data << 8) | (*(uchar *) cp); - } - - if ((rc = write_word (info, wp, data)) != 0) { - return (rc); - } - wp += 4; - } - - /* - * handle word aligned part - */ - while (cnt >= 4) { - data = 0; - for (i = 0; i < 4; ++i) { - data = (data << 8) | *src++; - } - if ((rc = write_word (info, wp, data)) != 0) { - return (rc); - } - wp += 4; - cnt -= 4; - } - - if (cnt == 0) { - return (0); - } - - /* - * handle unaligned tail bytes - */ - data = 0; - for (i = 0, cp = wp; i < 4 && cnt > 0; ++i, ++cp) { - data = (data << 8) | *src++; - --cnt; - } - for (; i < 4; ++i, ++cp) { - data = (data << 8) | (*(uchar *) cp); - } - - return (write_word (info, wp, data)); -} - -/*----------------------------------------------------------------------- - * Write a word to Flash, returns: - * 0 - OK - * 1 - write timeout - * 2 - Flash not erased - */ -static int write_word (flash_info_t * info, ulong dest, ulong data) -{ - volatile FLASH_WORD_SIZE *addr2 = - (FLASH_WORD_SIZE *) (info->start[0]); - volatile FLASH_WORD_SIZE *dest2 = (FLASH_WORD_SIZE *) dest; - volatile FLASH_WORD_SIZE *data2 = (FLASH_WORD_SIZE *) & data; - ulong start; - int i; - - /* Check if Flash is (sufficiently) erased */ - if ((*((volatile FLASH_WORD_SIZE *) dest) & - (FLASH_WORD_SIZE) data) != (FLASH_WORD_SIZE) data) { - return (2); - } - - for (i = 0; i < 4 / sizeof (FLASH_WORD_SIZE); i++) { - int flag; - - /* Disable interrupts which might cause a timeout here */ - flag = disable_interrupts (); - - addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA; - addr2[ADDR1] = (FLASH_WORD_SIZE) 0x00550055; - addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00A000A0; - - dest2[i] = data2[i]; - - /* re-enable interrupts if necessary */ - if (flag) - enable_interrupts (); - - /* data polling for D7 */ - start = get_timer (0); - while ((dest2[i] & (FLASH_WORD_SIZE) 0x00800080) != - (data2[i] & (FLASH_WORD_SIZE) 0x00800080)) { - - if (get_timer (start) > CONFIG_SYS_FLASH_WRITE_TOUT) { - return (1); - } - } - } - - return (0); -} diff --git a/board/jse/host_bridge.c b/board/jse/host_bridge.c deleted file mode 100644 index 76c07b0c35..0000000000 --- a/board/jse/host_bridge.c +++ /dev/null @@ -1,77 +0,0 @@ -/* - * Copyright (c) 2004 Picture Elements, Inc. - * Stephen Williams (steve@icarus.com) - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#ident "$Id:$" - -# include -# include -# include "jse_priv.h" - -/* - * The JSE board has an Intel 21555 non-transparent bridge for - * communication with the host. We need to render it harmless on the - * JSE side, but leave it alone on the host (primary) side. Normally, - * this will all be done before the host BIOS can gain access to the - * board, due to the Primary Access Lockout bit. - * - * The host_bridge_init function is called as a late initialization - * function, after most of the board is set up, including a PCI scan. - */ - -void host_bridge_init (void) -{ - /* The bridge chip is at a fixed location. */ - pci_dev_t dev = PCI_BDF (0, 10, 0); - - /* Set PCI Class code -- - The primary side sees this class code at 0x08 in the - primary config space. This must be something other then a - bridge, or MS Windows starts doing weird stuff to me. */ - pci_write_config_dword (dev, 0x48, 0x04800000); - - /* Set subsystem ID -- - The primary side sees this value at 0x2c. We set it here so - that the host can tell what sort of device this is: - We are a Picture Elements [0x12c5] JSE [0x008a]. */ - pci_write_config_dword (dev, 0x6c, 0x008a12c5); - - /* Downstream (Primary-to-Secondary) BARs are set up mostly - off. We need only the Memory-0 Bar so that the host can get - at the CSR region to set up tables and the lot. */ - - /* Downstream Memory 0 setup (4K for CSR) */ - pci_write_config_dword (dev, 0xac, 0xfffff000); - /* Downstream Memory 1 setup (off) */ - pci_write_config_dword (dev, 0xb0, 0x00000000); - /* Downstream Memory 2 setup (off) */ - pci_write_config_dword (dev, 0xb4, 0x00000000); - /* Downstream Memory 3 setup (off) */ - pci_write_config_dword (dev, 0xb8, 0x00000000); - - /* Upstream (Secondary-to-Primary) BARs are used to get at - host memory from the JSE card. Create two regions: a small - one to manage individual word reads/writes, and a larger - one for doing bulk frame moves. */ - - /* Upstream Memory 0 Setup -- (BAR2) 4K non-prefetchable */ - pci_write_config_dword (dev, 0xc4, 0xfffff000); - /* Upstream Memory 1 setup -- (BAR3) 4K non-prefetchable */ - pci_write_config_dword (dev, 0xc8, 0xfffff000); - - /* Upstream Memory 2 (BAR4) uses page translation, and is set - up in CCR1. Configure for 4K pages. */ - - /* Set CCR1,0 reigsters. This clears the Primary PCI Lockout - bit as well, so we are done configuring after this - point. Therefore, this must be the last step. - - CC1[15:12]= 0 (disable I2O message unit) - CC1[11:8] = 0x5 (4K page size) - CC0[11] = 1 (Secondary Clock Disable: disable clock) - CC0[10] = 0 (Primary Access Lockout: allow primary access) - */ - pci_write_config_dword (dev, 0xcc, 0x05000800); -} diff --git a/board/jse/init.S b/board/jse/init.S deleted file mode 100644 index 4e449fef20..0000000000 --- a/board/jse/init.S +++ /dev/null @@ -1,75 +0,0 @@ -/* - * SPDX-License-Identifier: GPL-2.0 IBM-pibs - */ -/*------------------------------------------------------------------------- */ -/* Function: ext_bus_cntlr_init */ -/* Description: Initializes the External Bus Controller for the external */ -/* peripherals. IMPORTANT: For pass1 this code must run from */ -/* cache since you can not reliably change a peripheral banks */ -/* timing register (pbxap) while running code from that bank. */ -/* For ex., since we are running from ROM on bank 0, we can NOT */ -/* execute the code that modifies bank 0 timings from ROM, so */ -/* we run it from cache. */ -/* */ -/* */ -/* The layout for the PEI JSE board: */ -/* Bank 0 - Flash and SRAM */ -/* Bank 1 - SystemACE */ -/* Bank 2 - not used */ -/* Bank 3 - not used */ -/* Bank 4 - not used */ -/* Bank 5 - not used */ -/* Bank 6 - not used */ -/* Bank 7 - not used */ -/*------------------------------------------------------------------------- */ -#include - -#include -#include - -#include -#include - - .globl ext_bus_cntlr_init -ext_bus_cntlr_init: - mflr r4 /* save link register */ - bl ..getAddr -..getAddr: - mflr r3 /* get address of ..getAddr */ - mtlr r4 /* restore link register */ - addi r4,0,14 /* set ctr to 10; used to prefetch */ - mtctr r4 /* 10 cache lines to fit this function */ - /* in cache (gives us 8x10=80 instrctns) */ -..ebcloop: - icbt r0,r3 /* prefetch cache line for addr in r3 */ - addi r3,r3,32 /* move to next cache line */ - bdnz ..ebcloop /* continue for 10 cache lines */ - - /*----------------------------------------------------------------- */ - /* Delay to ensure all accesses to ROM are complete before changing */ - /* bank 0 timings. 200usec should be enough. */ - /* 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles */ - /*----------------------------------------------------------------- */ - addis r3,0,0x0 - ori r3,r3,0xA000 /* ensure 200usec have passed since reset */ - mtctr r3 -..spinlp: - bdnz ..spinlp /* spin loop */ - - /*----------------------------------------------------------------- */ - /* Memory Bank 0 (Flash) initialization */ - /*----------------------------------------------------------------- */ - - addi r4,0,PB1AP - mtdcr EBC0_CFGADDR,r4 - addis r4,0,0x9B01 - ori r4,r4,0x5480 - mtdcr EBC0_CFGDATA,r4 - - addi r4,0,PB0CR - mtdcr EBC0_CFGADDR,r4 - addis r4,0,0xFFF1 /* BAS=0xFFF,BS=0x0(1MB),BU=0x3(R/W), */ - ori r4,r4,0x8000 /* BW=0x0( 8 bits) */ - mtdcr EBC0_CFGDATA,r4 - - blr diff --git a/board/jse/jse.c b/board/jse/jse.c deleted file mode 100644 index a0913c33f0..0000000000 --- a/board/jse/jse.c +++ /dev/null @@ -1,147 +0,0 @@ -/* - * Copyright (c) 2004 Picture Elements, Inc. - * Stephen Williams (steve@icarus.com) - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -# include -# include -# include -# include -# include "jse_priv.h" - -/* - * This function is run very early, out of flash, and before devices are - * initialized. It is called by arch/powerpc/lib/board.c:board_init_f by virtue - * of being in the init_sequence array. - * - * The SDRAM has been initialized already -- start.S:start called - * init.S:init_sdram early on -- but it is not yet being used for - * anything, not even stack. So be careful. - */ -int board_early_init_f (void) -{ - /*-------------------------------------------------------------------------+ - | Interrupt controller setup for the JSE board. - | Note: IRQ 0-15 405GP internally generated; active high; level sensitive - | IRQ 16 405GP internally generated; active low; level sensitive - | IRQ 17-24 RESERVED/UNUSED - | IRQ 25 (EXT IRQ 0) PCI SLOT 0; active low; level sensitive - | IRQ 26 (EXT IRQ 1) PCI SLOT 1; active low; level sensitive - | IRQ 27 (EXT IRQ 2) JP2C CHIP ; active low; level sensitive - | IRQ 28 (EXT IRQ 3) PCI bridge; active low; level sensitive - | IRQ 29 (EXT IRQ 4) SystemACE IRQ; active high - | IRQ 30 (EXT IRQ 5) SystemACE BRdy (unused) - | IRQ 31 (EXT IRQ 6) (unused) - +-------------------------------------------------------------------------*/ - mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */ - mtdcr (UIC0ER, 0x00000000); /* disable all ints */ - mtdcr (UIC0CR, 0x00000000); /* set all to be non-critical */ - mtdcr (UIC0PR, 0xFFFFFF87); /* set int polarities */ - mtdcr (UIC0TR, 0x10000000); /* set int trigger levels */ - mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */ - - /* Configure the interface to the SystemACE MCU port. - The SystemACE is fast, but there is no reason to have - excessivly tight timings. So the settings are slightly - generous. */ - - /* EBC0_B1AP: BME=1, TWT=2, CSN=0, OEN=1, - WBN=0, WBF=1, TH=0, RE=0, SOR=0, BEM=0, PEN=0 */ - mtdcr (EBC0_CFGADDR, PB1AP); - mtdcr (EBC0_CFGDATA, 0x01011000); - - /* EBC0_B1CR: BAS=x, BS=0(1MB), BU=3(R/W), BW=0(8bits) */ - mtdcr (EBC0_CFGADDR, PB1CR); - mtdcr (EBC0_CFGDATA, CONFIG_SYS_SYSTEMACE_BASE | 0x00018000); - - /* Enable the /PerWE output as /PerWE, instead of /PCIINT. */ - /* CPC0_CR1 |= PCIPW */ - mtdcr (0xb2, mfdcr (0xb2) | 0x00004000); - - return 0; -} - -#ifdef CONFIG_BOARD_PRE_INIT -int board_pre_init (void) -{ - return board_early_init_f (); -} - -#endif - -/* - * This function is also called by arch/powerpc/lib/board.c:board_init_f (it is - * also in the init_sequence array) but later. Many more things are - * configured, but we are still running from flash. - */ -int checkboard (void) -{ - unsigned vers, status; - - /* check that the SystemACE chip is alive. */ - printf ("ACE: "); - vers = readw (CONFIG_SYS_SYSTEMACE_BASE + 0x16); - printf ("SystemACE %u.%u (build %u)", - (vers >> 12) & 0x0f, (vers >> 8) & 0x0f, vers & 0xff); - - status = readl (CONFIG_SYS_SYSTEMACE_BASE + 0x04); -#ifdef DEBUG - printf (" STATUS=0x%08x", status); -#endif - /* If the flash card is present and there is an initial error, - then force a restart of the program. */ - if (status & 0x00000010) { - printf (" CFDETECT"); - - if (status & 0x04) { - /* CONTROLREG = CFGPROG */ - writew (0x1000, CONFIG_SYS_SYSTEMACE_BASE + 0x18); - udelay (500); - /* CONTROLREG = CFGRESET */ - writew (0x0080, CONFIG_SYS_SYSTEMACE_BASE + 0x18); - udelay (500); - writew (0x0000, CONFIG_SYS_SYSTEMACE_BASE + 0x18); - /* CONTROLREG = CFGSTART */ - writew (0x0020, CONFIG_SYS_SYSTEMACE_BASE + 0x18); - - status = readl (CONFIG_SYS_SYSTEMACE_BASE + 0x04); - } - } - - /* Wait for the SystemACE to program its chain of devices. */ - while ((status & 0x84) == 0x00) { - udelay (500); - status = readl (CONFIG_SYS_SYSTEMACE_BASE + 0x04); - } - - if (status & 0x04) - printf (" CFG-ERROR"); - if (status & 0x80) - printf (" CFGDONE"); - - printf ("\n"); - - /* Force /RTS to active. The board it not wired quite - correctly to use cts/rtc flow control, so just force the - /RST active and forget about it. */ - writeb (readb (0xef600404) | 0x03, 0xef600404); - - printf ("JSE: ready\n"); - - return 0; -} - -/* **** No more functions called by board_init_f. **** */ - -/* - * This function is called by arch/powerpc/lib/board.c:board_init_r. At this - * point, basic setup is done, U-Boot has been moved into SDRAM and - * PCI has been set up. From here we done late setup. - */ -int misc_init_r (void) -{ - host_bridge_init (); - return 0; -} diff --git a/board/jse/jse_priv.h b/board/jse/jse_priv.h deleted file mode 100644 index f61204bbae..0000000000 --- a/board/jse/jse_priv.h +++ /dev/null @@ -1,12 +0,0 @@ -#ifndef __jse_priv_H -#define __jse_prov_H -/* - * Copyright (c) 2004 Picture Elements, Inc. - * Stephen Williams (steve@icarus.com) - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -extern void host_bridge_init(void); - -#endif diff --git a/board/jse/sdram.c b/board/jse/sdram.c deleted file mode 100644 index 5639beddce..0000000000 --- a/board/jse/sdram.c +++ /dev/null @@ -1,169 +0,0 @@ -/* - * Copyright (c) 2004 Picture Elements, Inc. - * Stephen Williams (steve@icarus.com) - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include - -# define SDRAM_LEN 0x08000000 - -/* - * this is even after checkboard. It returns the size of the SDRAM - * that we have installed. This function is called by board_init_f - * in arch/powerpc/lib/board.c to initialize the memory and return what I - * found. - */ -phys_size_t initdram (int board_type) -{ - /* Configure the SDRAMS */ - - /* disable memory controller */ - mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG); - mtdcr (SDRAM0_CFGDATA, 0x00000000); - - udelay (500); - - /* Clear SDRAM0_BESR0 (Bus Error Syndrome Register) */ - mtdcr (SDRAM0_CFGADDR, SDRAM0_BESR0); - mtdcr (SDRAM0_CFGDATA, 0xffffffff); - - /* Clear SDRAM0_BESR1 (Bus Error Syndrome Register) */ - mtdcr (SDRAM0_CFGADDR, SDRAM0_BESR1); - mtdcr (SDRAM0_CFGDATA, 0xffffffff); - - /* Clear SDRAM0_ECCCFG (disable ECC) */ - mtdcr (SDRAM0_CFGADDR, SDRAM0_ECCCFG); - mtdcr (SDRAM0_CFGDATA, 0x00000000); - - /* Clear SDRAM0_ECCESR (ECC Error Syndrome Register) */ - mtdcr (SDRAM0_CFGADDR, SDRAM0_ECCESR); - mtdcr (SDRAM0_CFGDATA, 0xffffffff); - - /* Timing register: CASL=2, PTA=2, CTP=2, LDF=1, RFTA=5, RCD=2 */ - mtdcr (SDRAM0_CFGADDR, SDRAM0_TR); - mtdcr (SDRAM0_CFGDATA, 0x010a4016); - - /* Memory Bank 0 Config == BA=0x00000000, SZ=64M, AM=3, BE=1 */ - mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR); - mtdcr (SDRAM0_CFGDATA, 0x00084001); - - /* Memory Bank 1 Config == BA=0x04000000, SZ=64M, AM=3, BE=1 */ - mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR); - mtdcr (SDRAM0_CFGDATA, 0x04084001); - - /* Memory Bank 2 Config == BE=0 */ - mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR); - mtdcr (SDRAM0_CFGDATA, 0x00000000); - - /* Memory Bank 3 Config == BE=0 */ - mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR); - mtdcr (SDRAM0_CFGDATA, 0x00000000); - - /* refresh timer = 0x400 */ - mtdcr (SDRAM0_CFGADDR, SDRAM0_RTR); - mtdcr (SDRAM0_CFGDATA, 0x04000000); - - /* Power management idle timer set to the default. */ - mtdcr (SDRAM0_CFGADDR, SDRAM0_PMIT); - mtdcr (SDRAM0_CFGDATA, 0x07c00000); - - udelay (500); - - /* Enable banks (DCE=1, BPRF=1, ECCDD=1, EMDUL=1) */ - mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG); - mtdcr (SDRAM0_CFGDATA, 0x80e00000); - - return SDRAM_LEN; -} - -/* - * The U-Boot core, as part of the initialization to prepare for - * loading the monitor into SDRAM, requests of this function that the - * memory be tested. Return 0 if the memory tests OK. - */ -int testdram (void) -{ - unsigned long idx; - unsigned val; - unsigned errors; - volatile unsigned long *sdram; - -#ifdef DEBUG - printf ("SDRAM Controller Registers --\n"); - - mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG); - val = mfdcr (SDRAM0_CFGDATA); - printf (" SDRAM0_CFG : 0x%08x\n", val); - - mtdcr (SDRAM0_CFGADDR, 0x24); - val = mfdcr (SDRAM0_CFGDATA); - printf (" SDRAM0_STATUS: 0x%08x\n", val); - - mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR); - val = mfdcr (SDRAM0_CFGDATA); - printf (" SDRAM0_B0CR : 0x%08x\n", val); - - mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR); - val = mfdcr (SDRAM0_CFGDATA); - printf (" SDRAM0_B1CR : 0x%08x\n", val); - - mtdcr (SDRAM0_CFGADDR, SDRAM0_TR); - val = mfdcr (SDRAM0_CFGDATA); - printf (" SDRAM0_TR : 0x%08x\n", val); - - mtdcr (SDRAM0_CFGADDR, SDRAM0_RTR); - val = mfdcr (SDRAM0_CFGDATA); - printf (" SDRAM0_RTR : 0x%08x\n", val); -#endif - - /* Wait for memory to be ready by testing MRSCMPbit - bit. Really, there should already have been plenty of time, - given it was started long ago. But, best to check. */ - for (idx = 0; idx < 1000000; idx += 1) { - mtdcr (SDRAM0_CFGADDR, 0x24); - val = mfdcr (SDRAM0_CFGDATA); - if (val & 0x80000000) - break; - } - - if (!(val & 0x80000000)) { - printf ("SDRAM ERROR: SDRAM0_STATUS never set!\n"); - return 1; - } - - /* Start memory test. */ - printf ("test: %u MB - ", SDRAM_LEN / 1048576); - - sdram = (unsigned long *) CONFIG_SYS_SDRAM_BASE; - - printf ("write - "); - for (idx = 2; idx < SDRAM_LEN / 4; idx += 2) { - sdram[idx + 0] = idx; - sdram[idx + 1] = ~idx; - } - - printf ("read - "); - errors = 0; - for (idx = 2; idx < SDRAM_LEN / 4; idx += 2) { - if (sdram[idx + 0] != idx) - errors += 1; - if (sdram[idx + 1] != ~idx) - errors += 1; - if (errors > 0) - break; - } - - if (errors > 0) { - printf ("NOT OK\n"); - printf ("FIRST ERROR at %p: 0x%08lx:0x%08lx != 0x%08lx:0x%08lx\n", - sdram + idx, sdram[idx + 0], sdram[idx + 1], idx, ~idx); - return 1; - } - - printf ("ok\n"); - return 0; -} diff --git a/configs/JSE_defconfig b/configs/JSE_defconfig deleted file mode 100644 index 14c9c2feea..0000000000 --- a/configs/JSE_defconfig +++ /dev/null @@ -1,3 +0,0 @@ -CONFIG_PPC=y -CONFIG_4xx=y -CONFIG_TARGET_JSE=y diff --git a/doc/README.scrapyard b/doc/README.scrapyard index 481f4d8fdd..668431c57a 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order. Board Arch CPU Commit Removed Last known maintainer/contact ================================================================================================= +JSE powerpc ppc4xx - - Stephen Williams BC3450 powerpc mpc5xxx - - hawkboard arm arm926ejs cb957cda 2015-02-24 Syed Mohammed Khasim :Sughosh Ganu tnetv107x arm arm1176 50b82c4b 2015-02-24 Chan-Taek Park diff --git a/include/configs/JSE.h b/include/configs/JSE.h deleted file mode 100644 index 5cc25576ae..0000000000 --- a/include/configs/JSE.h +++ /dev/null @@ -1,276 +0,0 @@ -/* - * (C) Copyright 2003 Picture Elements, Inc. - * Stephen Williams - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options for the JSE board - * (Theoretically easy to change, but the board is fixed.) - */ - -#define CONFIG_JSE 1 - /* JSE has a PPC405GPr */ -#define CONFIG_405GP 1 - /* ... with a 33MHz OSC. connected to the SysCLK input */ -#define CONFIG_SYS_CLK_FREQ 33333333 - /* ... with on-chip memory here (4KBytes) */ -#define CONFIG_SYS_OCM_DATA_ADDR 0xF4000000 -#define CONFIG_SYS_OCM_DATA_SIZE 0x00001000 - /* Do not set up locked dcache as init ram. */ -#undef CONFIG_SYS_INIT_DCACHE_CS - -#define CONFIG_SYS_TEXT_BASE 0xFFF80000 - - /* Map the SystemACE chip (CS#1) here. (Must be a multiple of 1Meg) */ -#define CONFIG_SYSTEMACE 1 -#define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000 -#define CONFIG_SYS_SYSTEMACE_WIDTH 8 -#define CONFIG_DOS_PARTITION 1 - - /* Use the On-Chip-Memory (OCM) as a temporary stack for the startup code. */ -#define CONFIG_SYS_TEMP_STACK_OCM 1 - /* ... place INIT RAM in the OCM address */ -# define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR - /* ... give it the whole init ram */ -# define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE - /* ... Shave a bit off the end for global data */ -# define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - /* ... and place the stack pointer at the top of what's left. */ -# define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - - /* Enable board_pre_init function */ -#define CONFIG_BOARD_PRE_INIT 1 -#define CONFIG_BOARD_EARLY_INIT_F 1 - /* Disable post-clk setup init function */ -#undef CONFIG_BOARD_POSTCLK_INIT - /* Disable call to post_init_f: late init function. */ -#undef CONFIG_POST - /* Enable DRAM test. */ -#define CONFIG_SYS_DRAM_TEST 1 - /* Enable misc_init_r function. */ -#define CONFIG_MISC_INIT_R 1 - - /* JSE has EEPROM chips that are good for environment. */ -#undef CONFIG_ENV_IS_IN_NVRAM -#undef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_IS_IN_EEPROM 1 -#undef CONFIG_ENV_IS_NOWHERE - - /* This is the 7bit address of the device, not including P. */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 - /* After the device address, need one more address byte. */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - /* The EEPROM is 512 bytes. */ -#define CONFIG_SYS_EEPROM_SIZE 512 - /* The EEPROM can do 16byte ( 1 << 4 ) page writes. */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 - /* Put the environment in the second half. */ -#define CONFIG_ENV_OFFSET 0x00 -#define CONFIG_ENV_SIZE 512 - - /* The JSE connects UART1 to the console tap connector. */ -#define CONFIG_CONS_INDEX 2 -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() - - /* Set console baudrate to 9600 */ -#define CONFIG_BAUDRATE 9600 - -/* - * Configuration related to auto-boot. - * - * CONFIG_BOOTDELAY sets the delay (in seconds) that U-Boot will wait - * before resorting to autoboot. This value can be overridden by the - * bootdelay environment variable. - * - * CONFIG_AUTOBOOT_PROMPT is the string that U-Boot emits to warn the - * user that an autoboot will happen. - * - * CONFIG_BOOTCOMMAND is the sequence of commands that U-Boot will - * execute to boot the JSE. This loads the uimage and initrd.img files - * from CompactFlash into memory, then boots them from memory. - * - * CONFIG_BOOTARGS is the arguments passed to the Linux kernel to get - * it going on the JSE. - */ -#define CONFIG_BOOTDELAY 5 -#define CONFIG_BOOTARGS "root=/dev/ram0 init=/linuxrc rw" -#define CONFIG_BOOTCOMMAND "fatload ace 0 2000000 uimage; fatload ace 0 2100000 initrd.img; bootm 2000000 2100000" - - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_PPC4xx_EMAC -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 1 /* PHY address */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_FAT -#define CONFIG_CMD_FLASH -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_PCI -#define CONFIG_CMD_PING - - - /* watchdog disabled */ -#undef CONFIG_WATCHDOG - /* SPD EEPROM (sdram speed config) disabled */ -#undef CONFIG_SPD_EEPROM -#undef SPD_EEPROM_ADDRESS - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -/* - * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1. - * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31. - * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value. - * The Linux BASE_BAUD define should match this configuration. - * baseBaud = cpuClock/(uartDivisor*16) - * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, - * set Linux BASE_BAUD to 403200. - */ -#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ -#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ -#define CONFIG_SYS_BASE_BAUD 691200 - -/* The following table includes the supported baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F - - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ -#undef CONFIG_PCI_PNP /* do pci plug-and-play */ - /* resource configuration */ - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */ -#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ -#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ - -/*----------------------------------------------------------------------- - * External peripheral base address - *----------------------------------------------------------------------- - */ -#undef CONFIG_IDE_LED /* no led for ide supported */ -#undef CONFIG_IDE_RESET /* no reset for ide supported */ - -#define CONFIG_SYS_KEY_REG_BASE_ADDR 0xF0100000 -#define CONFIG_SYS_IR_REG_BASE_ADDR 0xF0200000 -#define CONFIG_SYS_FPGA_REG_BASE_ADDR 0xF0300000 - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xFFF80000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ - -#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */ -#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */ - - -/* Configuration Port location */ -#define CONFIG_PORT_ADDR 0xF0000500 - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif -#endif /* __CONFIG_H */