From: Mikhail Zhilkin Date: Sun, 11 Jun 2023 20:50:23 +0000 (+0000) Subject: ramips: add support for Sercomm S1500 devices X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=2d6784a033a994043759fa3b94c48afd5df81f88;p=openwrt%2Fstaging%2Fblogic.git ramips: add support for Sercomm S1500 devices This commit adds support for following wireless routers: - Beeline SmartBox PRO (Serсomm S1500 AWI) - WiFire S1500.NBN (Serсomm S1500 BUC) This commit is based on this PR: - Link: https://github.com/openwrt/openwrt/pull/4770 - Author: Maximilian Weinmann The opening of this PR was agreed with author. My changes: - Sorting, minor changes and some movings between dts and dtsi - Move leds to dts when possible - Recipes for the factory image - Update of the installation/recovery/return to stock guides - Add reset GPIO for the pcie1 Common specification -------------------- SoC: MediaTek MT7621AT (880 MHz, 2 cores) Switch: MediaTek MT7530 (via SoC MT7621AT) Wireless: 2.4 GHz, MT7602EN, b/g/n, 2x2 Wireless: 5 GHz, MT7612EN, a/n/ac, 2x2 Ethernet: 5 ports - 5×GbE (WAN, LAN1-4) Mini PCIe: via J2 on PCB, not soldered on the board UART: J4 -> GND[], TX, VCC(3.3V), RX BootLoader: U-Boot SerComm/Mediatek Beeline SmartBox PRO specification ---------------------------------- RAM (Nanya NT5CB128M16FP): 256 MiB NAND-Flash (ESMT F59L2G81A): 256 MiB USB ports: 2xUSB2.0 LEDs: Status (white), WPS (blue), 2g (white), 5g (white) + 10 LED Ethernet Buttons: 2 button (reset, wps), 1 switch button (ROUT<->REP) Power: 12 VDC, 1.5 A PCB Sticker: 970AWI0QW00N256SMT Ver. 1.0 CSN: SG15******** MAC LAN: 94:4A:0C:**:**:** Manufacturer's code: 0AWI0500QW1 WiFire S1500.NBN specification ------------------------------ RAM (Nanya NT5CC64M16GP): 128 MiB NAND-Flash (ESMT F59L1G81MA): 128 MiB USB ports: 1xUSB2.0 LEDs: Status (white), WPS (white), 2g (white), 5g (white) + 10 LED Ethernet Buttons: 2 button (RESET, WPS) Power: 12 VDC, 1.0 A PCB Sticker: 970BUC0RW00N128SMT Ver. 1.0 CSN: MH16******** MAC WAN: E0:60:66:**:**:** Manufacturer's code: 0BUC0500RW1 MAC address table (PRO) ----------------------- use address source LAN *:23 factory 0x1000 (label) WAN *:24 factory $label +1 2g *:23 factory $label 5g *:25 factory $label +2 MAC addresses (NBN) ------------------- use address source LAN *:0e factory 0x1000 WAN *:0f LAN +1 (label) 2g *:0f LAN +1 5g *:10 LAN +2 OEM easy installation --------------------- 1. Remove all dots from the factory image filename (except the dot before file extension) 2. Upload and update the firmware via the original web interface 3. Two options are possible after the reboot: a. OpenWrt - that's OK, the mission accomplished b. Stock firmware - install Stock firmware (to switch booflag from Sercomm0 to Sercomm1) and then OpenWrt factory image. Return to Stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2 reboot 2. Install stock firmware via the web OEM firmware interface Recovery -------- Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery Tested-by: Pavel Ivanov Tested-by: Denis Myshaev Tested-by: Oleg Galeev Tested-By: Ivan Pavlov Co-authored-by: Maximilian Weinmann Signed-off-by: Mikhail Zhilkin --- diff --git a/package/boot/uboot-envtools/files/ramips b/package/boot/uboot-envtools/files/ramips index d4154cda499a..c94f8d69c74f 100644 --- a/package/boot/uboot-envtools/files/ramips +++ b/package/boot/uboot-envtools/files/ramips @@ -45,6 +45,13 @@ etisalat,s3|\ rostelecom,rt-sf-1) ubootenv_add_uci_config "/dev/mtd0" "0x80000" "0x1000" "0x20000" ;; +beeline,smartbox-pro|\ +tplink,ec330-g5u-v1|\ +wifire,s1500-nbn) + idx="$(find_mtd_index u-boot-env)" + [ -n "$idx" ] && \ + ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x1000" "0x20000" + ;; buffalo,wsr-1166dhp|\ buffalo,wsr-600dhp|\ kroks,kndrt31r16|\ @@ -98,11 +105,6 @@ snr,cpe-w4n-mt) [ -n "$idx" ] && \ ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x1000" "0x1000" ;; -tplink,ec330-g5u-v1) - idx="$(find_mtd_index u-boot-env)" - [ -n "$idx" ] && \ - ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x1000" "0x20000" - ;; xiaomi,mi-router-3g-v2|\ xiaomi,mi-router-4a-gigabit|\ xiaomi,miwifi-3c) diff --git a/target/linux/ramips/dts/mt7621_beeline_smartbox-pro.dts b/target/linux/ramips/dts/mt7621_beeline_smartbox-pro.dts new file mode 100644 index 000000000000..e3e248d48f96 --- /dev/null +++ b/target/linux/ramips/dts/mt7621_beeline_smartbox-pro.dts @@ -0,0 +1,118 @@ +// SPDX-License-Identifier: GPL-2.0-or-later + +#include "mt7621_sercomm_s1500.dtsi" + +/ { + compatible = "beeline,smartbox-pro", "mediatek,mt7621-soc"; + model = "Beeline SmartBox PRO"; + + aliases { + label-mac-device = &gmac0; + }; + + keys { + switch_bt { + label = "ROUT<->REP Switch_bt"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + linux,input-type = ; + linux,code = ; + debounce-interval = <60>; + }; + }; + + ubi-concat { + compatible = "mtd-concat"; + devices = <&ubiconcat0 &ubiconcat1 &ubiconcat2 &ubiconcat3 \ + &ubiconcat4 &ubiconcat5 &ubiconcat6>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "ubi"; + reg = <0x0 0xd2e0000>; + }; + }; + }; +}; + +&led_wps { + label = "blue:wps"; + color = ; +}; + +&partitions { + partition@0_all { + label = "ALL"; + reg = <0x0 0xff80000>; + read-only; + }; + + partition@200000 { + label = "sys_data"; + reg = <0x200000 0x1400000>; + + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + ubiconcat5: partition@0 { + label = "sys_data_1"; + reg = <0x0 0x600000>; + }; + + /* + * Sercomm U-Boot saves the environment at 0x800000 from + * the start of the NAND, destroying the "sys_data" + * partition. To prevent this, we split "sys_data" into + * two parts with "u-boot-env" partition between them. + */ + partition@600000 { + label = "u-boot-env"; + reg = <0x600000 0x20000>; + }; + + ubiconcat6: partition@620000 { + label = "sys_data_2"; + reg = <0x620000 0xde0000>; + }; + }; + + ubiconcat0: partition@1f00000 { + label = "RootFS_1"; + reg = <0x1f00000 0x1e00000>; + }; + + partition@3d00000 { + label = "RootFS_2"; + reg = <0x3d00000 0x1e00000>; + read-only; + }; + + ubiconcat1: partition@5b00000 { + label = "JVM/OSGI1"; + reg = <0x5b00000 0x3200000>; + }; + + ubiconcat2: partition@8d00000 { + label = "JVM/OSGI2"; + reg = <0x8d00000 0x3200000>; + }; + + ubiconcat3: partition@bf00000 { + label = "OSGI data"; + reg = <0xbf00000 0x3c00000>; + }; + + ubiconcat4: partition@fb00000 { + label = "Ftool"; + reg = <0xfb00000 0x100000>; + }; + + /* + * 4 MiB Reserved for the Bad Blocka + * 0x10000000-0xfc00000=0x400000 + */ +}; diff --git a/target/linux/ramips/dts/mt7621_sercomm_s1500.dtsi b/target/linux/ramips/dts/mt7621_sercomm_s1500.dtsi new file mode 100644 index 000000000000..91053f15bc14 --- /dev/null +++ b/target/linux/ramips/dts/mt7621_sercomm_s1500.dtsi @@ -0,0 +1,281 @@ +// SPDX-License-Identifier: GPL-2.0-or-later + +#include "mt7621.dtsi" + +#include +#include +#include + +/ { + aliases { + led-boot = &led_status; + led-running = &led_status; + led-upgrade = &led_wps; + led-failsafe = &led_wps; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&gpio 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led-0 { + label = "amber:lan4"; + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <0>; + linux,default-trigger = "mt7530-0:00:1Gbps"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + }; + + led-1 { + label = "green:lan4"; + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <1>; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + + led-2 { + label = "amber:lan3"; + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <2>; + linux,default-trigger = "mt7530-0:01:1Gbps"; + gpios = <&gpio 10 GPIO_ACTIVE_LOW>; + }; + + led-3 { + label = "green:lan3"; + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <3>; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + }; + + led-4 { + label = "amber:lan2"; + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <4>; + linux,default-trigger = "mt7530-0:02:1Gbps"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + + led-5 { + label = "amber:lan1"; + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <5>; + linux,default-trigger = "mt7530-0:03:1Gbps"; + gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + }; + + led-6 { + label = "green:lan1"; + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <6>; + gpios = <&gpio 23 GPIO_ACTIVE_LOW>; + }; + + led-7 { + label = "amber:wan"; + color = ; + function = LED_FUNCTION_WAN; + function-enumerator = <0>; + linux,default-trigger = "mt7530-0:04:1Gbps"; + gpios = <&gpio 24 GPIO_ACTIVE_LOW>; + }; + + led-8 { + label = "green:wan"; + color = ; + function = LED_FUNCTION_WAN; + function-enumerator = <1>; + gpios = <&gpio 25 GPIO_ACTIVE_LOW>; + }; + + led-9 { + label = "green:lan2"; + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <7>; + gpios = <&gpio 26 GPIO_ACTIVE_LOW>; + }; + + led-10 { + label = "white:wlan2g"; + color = ; + function = LED_FUNCTION_WLAN; + function-enumerator = <0>; + linux,default-trigger = "phy1radio"; + gpios = <&gpio 28 GPIO_ACTIVE_LOW>; + }; + + led_wps: led-11 { + function = LED_FUNCTION_WPS; + function-enumerator = <0>; + gpios = <&gpio 29 GPIO_ACTIVE_LOW>; + panic-indicator; + }; + + led_status: led-12 { + label = "white:status"; + color = ; + function = LED_FUNCTION_STATUS; + function-enumerator = <0>; + gpios = <&gpio 30 GPIO_ACTIVE_LOW>; + }; + + led-13 { + label = "white:wlan5g"; + color = ; + function = LED_FUNCTION_WLAN; + function-enumerator = <1>; + linux,default-trigger = "phy0radio"; + gpios = <&gpio 32 GPIO_ACTIVE_LOW>; + }; + }; +}; + +ðernet { + pinctrl-0 = <&mdio_pins>, <&rgmii1_pins>; +}; + +&gmac0 { + nvmem-cells = <&macaddr_factory_1000>; + nvmem-cell-names = "mac-address"; +}; + +&nand { + status = "okay"; + + partitions: partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x100000>; + read-only; + }; + + factory: partition@100000 { + label = "Factory"; + reg = <0x100000 0x100000>; + read-only; + + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_factory_1000: macaddr@1000 { + reg = <0x1000 0x6>; + }; + }; + + partition@1600000 { + label = "boot_flag"; + reg = <0x1600000 0x100000>; + }; + + partition@1700000 { + label = "kernel"; + reg = <0x1700000 0x400000>; + }; + + partition@1b00000 { + label = "Kernel_2"; + reg = <0x1b00000 0x400000>; + read-only; + }; + }; +}; + +&pcie { + status = "okay"; + + reset-gpios = <&gpio 8 GPIO_ACTIVE_LOW>, + <&gpio 19 GPIO_ACTIVE_LOW>; +}; + +&pcie0 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + ieee80211-freq-limit = <5000000 6000000>; + mediatek,mtd-eeprom = <&factory 0x8000>; + + nvmem-cells = <&macaddr_factory_1000>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <2>; + }; +}; + +&pcie1 { + wlan_2g: wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + ieee80211-freq-limit = <2400000 2500000>; + mediatek,mtd-eeprom = <&factory 0x0>; + + nvmem-cells = <&macaddr_factory_1000>; + nvmem-cell-names = "mac-address"; + }; +}; + +&state_default { + gpio { + groups = "wdt", "uart3", "jtag", "uart2", "i2c", "rgmii2"; + function = "gpio"; + }; +}; + +&switch0 { + ports { + port@0 { + status = "okay"; + label = "lan4"; + }; + + port@1 { + status = "okay"; + label = "lan3"; + }; + + port@2 { + status = "okay"; + label = "lan2"; + }; + + port@3 { + status = "okay"; + label = "lan1"; + }; + + wan: port@4 { + status = "okay"; + label = "wan"; + + nvmem-cells = <&macaddr_factory_1000>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <1>; + }; + }; +}; diff --git a/target/linux/ramips/dts/mt7621_wifire_s1500-nbn.dts b/target/linux/ramips/dts/mt7621_wifire_s1500-nbn.dts new file mode 100644 index 000000000000..6c0e2965aa0d --- /dev/null +++ b/target/linux/ramips/dts/mt7621_wifire_s1500-nbn.dts @@ -0,0 +1,81 @@ +// SPDX-License-Identifier: GPL-2.0-or-later + +#include "mt7621_sercomm_s1500.dtsi" + +/ { + compatible = "wifire,s1500-nbn", "mediatek,mt7621-soc"; + model = "WiFire S1500.NBN"; + + aliases { + label-mac-device = &wan; + }; + + ubi-concat { + compatible = "mtd-concat"; + devices = <&ubiconcat0 &ubiconcat1 &ubiconcat2 &ubiconcat3>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "ubi"; + reg = <0x0 0x4680000>; + }; + }; + }; +}; + +&led_wps { + label = "white:wps"; + color = ; +}; + +&partitions { + partition@0_all { + label = "ALL"; + reg = <0x0 0x7f80000>; + read-only; + }; + + partition@80000 { + label = "u-boot-env"; + reg = <0x80000 0x20000>; + }; + + ubiconcat1: partition@200000 { + label = "sys_data"; + reg = <0x200000 0x1400000>; + }; + + ubiconcat0: partition@1f00000 { + label = "RootFS_1"; + reg = <0x1f00000 0x2e00000>; + }; + + partition@4d00000 { + label = "RootFS_2"; + reg = <0x4d00000 0x2e00000>; + read-only; + }; + + ubiconcat2: partition@7b00000 { + label = "Ftool"; + reg = <0x7b00000 0x100000>; + }; + + ubiconcat3: partition@7c00000 { + label = "BCT"; + reg = <0x7c00000 0x380000>; + }; + + /* + * 512 KiB reserved for the Bad Blocks + * 0x8000000-0x7f80000=0x80000 + */ +}; + +&wlan_2g { + mac-address-increment = <1>; +}; diff --git a/target/linux/ramips/image/common-sercomm.mk b/target/linux/ramips/image/common-sercomm.mk index b743df440809..4060da092357 100644 --- a/target/linux/ramips/image/common-sercomm.mk +++ b/target/linux/ramips/image/common-sercomm.mk @@ -1,6 +1,12 @@ DEVICE_VARS += SERCOMM_KERNEL_OFFSET SERCOMM_ROOTFS_OFFSET DEVICE_VARS += SERCOMM_KERNEL2_OFFSET SERCOMM_ROOTFS2_OFFSET +define Build/sercomm-append-tail + printf 16 | dd seek=$$((0x90)) of=$@ bs=1 conv=notrunc 2>/dev/null + printf 11223344556677889900112233445566 | \ + sed 's/../\\x&/g' | xargs -d . printf >> $@ +endef + define Build/sercomm-crypto $(TOPDIR)/scripts/sercomm-crypto.py \ --input-file $@ \ @@ -32,6 +38,10 @@ define Build/sercomm-factory-cqr mv $@.fhdr $@ endef +define Build/sercomm-fix-buc-pid + printf 1 | dd seek=$$((0x13)) of=$@ bs=1 conv=notrunc 2>/dev/null +endef + define Build/sercomm-kernel $(TOPDIR)/scripts/sercomm-kernel-header.py \ --kernel-image $@ \ @@ -102,19 +112,28 @@ define Build/sercomm-prepend-tagged-kernel mv $(IMAGE_KERNEL).tagged $@ endef +define Build/sercomm-reset-slot1-chksum + printf "\xff\xff\xff\xff" | \ + dd of=$@ seek=$$((0x118)) bs=1 conv=notrunc 2>/dev/null +endef + define Device/sercomm $(Device/nand) LOADER_TYPE := bin + IMAGES += factory.img +endef + +define Device/sercomm_cxx_dxx + $(Device/sercomm) KERNEL_SIZE := 6144k KERNEL_LOADADDR := 0x81001000 LZMA_TEXT_START := 0x82800000 SERCOMM_KERNEL_OFFSET := 0x400100 SERCOMM_ROOTFS_OFFSET := 0x1000000 - IMAGES += factory.img endef define Device/sercomm_cxx - $(Device/sercomm) + $(Device/sercomm_cxx_dxx) SERCOMM_KERNEL2_OFFSET := 0xa00100 SERCOMM_ROOTFS2_OFFSET := 0x3000000 KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | lzma -a0 | \ @@ -126,7 +145,7 @@ define Device/sercomm_cxx endef define Device/sercomm_dxx - $(Device/sercomm) + $(Device/sercomm_cxx_dxx) KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | lzma -a0 | \ uImage lzma | sercomm-kernel KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | loader-kernel | \ @@ -136,3 +155,17 @@ define Device/sercomm_dxx sercomm-part-tag rootfs | sercomm-prepend-tagged-kernel kernel | \ gzip | sercomm-payload | sercomm-crypto endef + +define Device/sercomm_s1500 + $(Device/sercomm) + SERCOMM_KERNEL_OFFSET := 0x1700100 + SERCOMM_ROOTFS_OFFSET := 0x1f00000 + SERCOMM_KERNEL2_OFFSET := 0x1b00100 + KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | lzma -a0 | \ + uImage lzma + KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | loader-kernel | \ + lzma -a0 | uImage lzma + IMAGE/sysupgrade.bin := append-kernel | sercomm-kernel | \ + sysupgrade-tar kernel=$$$$@ | append-metadata + DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 +endef diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index ef02807ec130..4dc7607126a2 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -398,6 +398,23 @@ define Device/beeline_smartbox-giga endef TARGET_DEVICES += beeline_smartbox-giga +define Device/beeline_smartbox-pro + $(Device/sercomm_s1500) + DEVICE_VENDOR := Beeline + DEVICE_MODEL := SmartBox PRO + DEVICE_ALT0_VENDOR := Sercomm + DEVICE_ALT0_MODEL := S1500 AWI + IMAGE_SIZE := 34816k + IMAGE/factory.img := append-kernel | sercomm-kernel-factory | \ + sercomm-reset-slot1-chksum | append-ubi | check-size | \ + sercomm-factory-cqr | sercomm-append-tail | sercomm-mkhash + SERCOMM_HWID := AWI + SERCOMM_HWVER := 10000 + SERCOMM_ROOTFS2_OFFSET := 0x3d00000 + SERCOMM_SWVER := 2020 +endef +TARGET_DEVICES += beeline_smartbox-pro + define Device/beeline_smartbox-turbo $(Device/sercomm_dxx) IMAGE_SIZE := 32768k @@ -2453,6 +2470,24 @@ define Device/wevo_w2914ns-v2 endef TARGET_DEVICES += wevo_w2914ns-v2 +define Device/wifire_s1500-nbn + $(Device/sercomm_s1500) + DEVICE_VENDOR := WiFire + DEVICE_MODEL := S1500.NBN + DEVICE_ALT0_VENDOR := Sercomm + DEVICE_ALT0_MODEL := S1500 BUC + IMAGE_SIZE := 51200k + IMAGE/factory.img := append-kernel | sercomm-kernel-factory | \ + sercomm-reset-slot1-chksum | append-ubi | check-size | \ + sercomm-factory-cqr | sercomm-fix-buc-pid | sercomm-mkhash | \ + sercomm-crypto + SERCOMM_HWID := BUC + SERCOMM_HWVER := 10000 + SERCOMM_ROOTFS2_OFFSET := 0x4d00000 + SERCOMM_SWVER := 2015 +endef +TARGET_DEVICES += wifire_s1500-nbn + define Device/winstars_ws-wn583a6 $(Device/dsa-migration) $(Device/uimage-lzma-loader) diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds index 188605a6714b..1de35104c325 100644 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds @@ -40,6 +40,14 @@ etisalat,s3|\ rostelecom,rt-sf-1) ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan" ;; +beeline,smartbox-pro|\ +wifire,s1500-nbn) + ucidef_set_led_netdev "lan1" "lan1" "green:lan1" "lan1" "link tx rx" + ucidef_set_led_netdev "lan2" "lan2" "green:lan2" "lan2" "link tx rx" + ucidef_set_led_netdev "lan3" "lan3" "green:lan3" "lan3" "link tx rx" + ucidef_set_led_netdev "lan4" "lan4" "green:lan4" "lan4" "link tx rx" + ucidef_set_led_netdev "wan" "wan" "green:wan" "wan" "link tx rx" + ;; belkin,rt1800) ucidef_set_led_netdev "wan" "wan" "white:wan" "wan" ;; diff --git a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh index fa4b8fcc82ef..3c6d02f4fa6a 100755 --- a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh @@ -59,6 +59,7 @@ platform_do_upgrade() { asus,rt-ax54|\ beeline,smartbox-flash|\ beeline,smartbox-giga|\ + beeline,smartbox-pro|\ beeline,smartbox-turbo|\ beeline,smartbox-turbo-plus|\ belkin,rt1800|\ @@ -107,6 +108,7 @@ platform_do_upgrade() { sercomm,na502s|\ sim,simax1800t|\ tplink,ec330-g5u-v1|\ + wifire,s1500-nbn|\ xiaomi,mi-router-3g|\ xiaomi,mi-router-3-pro|\ xiaomi,mi-router-4|\