From: Christian Marangi Date: Sat, 27 Jan 2024 15:31:18 +0000 (+0100) Subject: generic: 6.1: backport qca808x LED support patch X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=2c39269b6e00a9811e7ae54e7358e79b0589de0c;p=openwrt%2Fstaging%2Fstintel.git generic: 6.1: backport qca808x LED support patch Backport qca808x LED support patch merged upstream needed to drop handling of it from the SSDK for ipq807x target. Signed-off-by: Christian Marangi --- diff --git a/target/linux/generic/backport-6.1/712-v6.9-net-phy-at803x-add-LED-support-for-qca808x.patch b/target/linux/generic/backport-6.1/712-v6.9-net-phy-at803x-add-LED-support-for-qca808x.patch new file mode 100644 index 0000000000..36675e7588 --- /dev/null +++ b/target/linux/generic/backport-6.1/712-v6.9-net-phy-at803x-add-LED-support-for-qca808x.patch @@ -0,0 +1,408 @@ +From 7196062b64ee470b91015f3d2e82d225948258ea Mon Sep 17 00:00:00 2001 +From: Christian Marangi +Date: Thu, 25 Jan 2024 21:37:01 +0100 +Subject: [PATCH 5/5] net: phy: at803x: add LED support for qca808x + +Add LED support for QCA8081 PHY. + +Documentation for this LEDs PHY is very scarce even with NDA access +to Documentation for OEMs. Only the blink pattern are documented and are +very confusing most of the time. No documentation is present about +forcing the LED on/off or to always blink. + +Those settings were reversed by poking the regs and trying to find the +correct bits to trigger these modes. Some bits mode are not clear and +maybe the documentation option are not 100% correct. For the sake of LED +support the reversed option are enough to add support for current LED +APIs. + +Supported HW control modes are: +- tx +- rx +- link_10 +- link_100 +- link_1000 +- link_2500 +- half_duplex +- full_duplex + +Also add support for LED polarity set to set LED polarity to active +high or low. QSDK sets this value to high by default but PHY reset value +doesn't have this enabled by default. + +QSDK also sets 2 additional bits but their usage is not clear, info about +this is added in the header. It was verified that for correct function +of the LED if active high is needed, only BIT 6 is needed. + +Signed-off-by: Christian Marangi +Reviewed-by: Andrew Lunn +Link: https://lore.kernel.org/r/20240125203702.4552-6-ansuelsmth@gmail.com +Signed-off-by: Jakub Kicinski +--- + drivers/net/phy/at803x.c | 327 +++++++++++++++++++++++++++++++++++++++ + 1 file changed, 327 insertions(+) + +--- a/drivers/net/phy/at803x.c ++++ b/drivers/net/phy/at803x.c +@@ -301,6 +301,87 @@ + /* Added for reference of existence but should be handled by wait_for_completion already */ + #define QCA808X_CDT_STATUS_STAT_BUSY (BIT(1) | BIT(3)) + ++#define QCA808X_MMD7_LED_GLOBAL 0x8073 ++#define QCA808X_LED_BLINK_1 GENMASK(11, 6) ++#define QCA808X_LED_BLINK_2 GENMASK(5, 0) ++/* Values are the same for both BLINK_1 and BLINK_2 */ ++#define QCA808X_LED_BLINK_FREQ_MASK GENMASK(5, 3) ++#define QCA808X_LED_BLINK_FREQ_2HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x0) ++#define QCA808X_LED_BLINK_FREQ_4HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x1) ++#define QCA808X_LED_BLINK_FREQ_8HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x2) ++#define QCA808X_LED_BLINK_FREQ_16HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x3) ++#define QCA808X_LED_BLINK_FREQ_32HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x4) ++#define QCA808X_LED_BLINK_FREQ_64HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x5) ++#define QCA808X_LED_BLINK_FREQ_128HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x6) ++#define QCA808X_LED_BLINK_FREQ_256HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x7) ++#define QCA808X_LED_BLINK_DUTY_MASK GENMASK(2, 0) ++#define QCA808X_LED_BLINK_DUTY_50_50 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x0) ++#define QCA808X_LED_BLINK_DUTY_75_25 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x1) ++#define QCA808X_LED_BLINK_DUTY_25_75 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x2) ++#define QCA808X_LED_BLINK_DUTY_33_67 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x3) ++#define QCA808X_LED_BLINK_DUTY_67_33 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x4) ++#define QCA808X_LED_BLINK_DUTY_17_83 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x5) ++#define QCA808X_LED_BLINK_DUTY_83_17 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x6) ++#define QCA808X_LED_BLINK_DUTY_8_92 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x7) ++ ++#define QCA808X_MMD7_LED2_CTRL 0x8074 ++#define QCA808X_MMD7_LED2_FORCE_CTRL 0x8075 ++#define QCA808X_MMD7_LED1_CTRL 0x8076 ++#define QCA808X_MMD7_LED1_FORCE_CTRL 0x8077 ++#define QCA808X_MMD7_LED0_CTRL 0x8078 ++#define QCA808X_MMD7_LED_CTRL(x) (0x8078 - ((x) * 2)) ++ ++/* LED hw control pattern is the same for every LED */ ++#define QCA808X_LED_PATTERN_MASK GENMASK(15, 0) ++#define QCA808X_LED_SPEED2500_ON BIT(15) ++#define QCA808X_LED_SPEED2500_BLINK BIT(14) ++/* Follow blink trigger even if duplex or speed condition doesn't match */ ++#define QCA808X_LED_BLINK_CHECK_BYPASS BIT(13) ++#define QCA808X_LED_FULL_DUPLEX_ON BIT(12) ++#define QCA808X_LED_HALF_DUPLEX_ON BIT(11) ++#define QCA808X_LED_TX_BLINK BIT(10) ++#define QCA808X_LED_RX_BLINK BIT(9) ++#define QCA808X_LED_TX_ON_10MS BIT(8) ++#define QCA808X_LED_RX_ON_10MS BIT(7) ++#define QCA808X_LED_SPEED1000_ON BIT(6) ++#define QCA808X_LED_SPEED100_ON BIT(5) ++#define QCA808X_LED_SPEED10_ON BIT(4) ++#define QCA808X_LED_COLLISION_BLINK BIT(3) ++#define QCA808X_LED_SPEED1000_BLINK BIT(2) ++#define QCA808X_LED_SPEED100_BLINK BIT(1) ++#define QCA808X_LED_SPEED10_BLINK BIT(0) ++ ++#define QCA808X_MMD7_LED0_FORCE_CTRL 0x8079 ++#define QCA808X_MMD7_LED_FORCE_CTRL(x) (0x8079 - ((x) * 2)) ++ ++/* LED force ctrl is the same for every LED ++ * No documentation exist for this, not even internal one ++ * with NDA as QCOM gives only info about configuring ++ * hw control pattern rules and doesn't indicate any way ++ * to force the LED to specific mode. ++ * These define comes from reverse and testing and maybe ++ * lack of some info or some info are not entirely correct. ++ * For the basic LED control and hw control these finding ++ * are enough to support LED control in all the required APIs. ++ * ++ * On doing some comparison with implementation with qca807x, ++ * it was found that it's 1:1 equal to it and confirms all the ++ * reverse done. It was also found further specification with the ++ * force mode and the blink modes. ++ */ ++#define QCA808X_LED_FORCE_EN BIT(15) ++#define QCA808X_LED_FORCE_MODE_MASK GENMASK(14, 13) ++#define QCA808X_LED_FORCE_BLINK_1 FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x3) ++#define QCA808X_LED_FORCE_BLINK_2 FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x2) ++#define QCA808X_LED_FORCE_ON FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x1) ++#define QCA808X_LED_FORCE_OFF FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x0) ++ ++#define QCA808X_MMD7_LED_POLARITY_CTRL 0x901a ++/* QSDK sets by default 0x46 to this reg that sets BIT 6 for ++ * LED to active high. It's not clear what BIT 3 and BIT 4 does. ++ */ ++#define QCA808X_LED_ACTIVE_HIGH BIT(6) ++ + /* QCA808X 1G chip type */ + #define QCA808X_PHY_MMD7_CHIP_TYPE 0x901d + #define QCA808X_PHY_CHIP_TYPE_1G BIT(0) +@@ -346,6 +427,7 @@ struct at803x_priv { + struct regulator_dev *vddio_rdev; + struct regulator_dev *vddh_rdev; + u64 stats[ARRAY_SIZE(qca83xx_hw_stats)]; ++ int led_polarity_mode; + }; + + struct at803x_context { +@@ -706,6 +788,9 @@ static int at803x_probe(struct phy_devic + if (!priv) + return -ENOMEM; + ++ /* Init LED polarity mode to -1 */ ++ priv->led_polarity_mode = -1; ++ + phydev->priv = priv; + + ret = at803x_parse_dt(phydev); +@@ -2235,6 +2320,242 @@ static void qca808x_link_change_notify(s + phydev->link ? QCA8081_PHY_FIFO_RSTN : 0); + } + ++static int qca808x_led_parse_netdev(struct phy_device *phydev, unsigned long rules, ++ u16 *offload_trigger) ++{ ++ /* Parsing specific to netdev trigger */ ++ if (test_bit(TRIGGER_NETDEV_TX, &rules)) ++ *offload_trigger |= QCA808X_LED_TX_BLINK; ++ if (test_bit(TRIGGER_NETDEV_RX, &rules)) ++ *offload_trigger |= QCA808X_LED_RX_BLINK; ++ if (test_bit(TRIGGER_NETDEV_LINK_10, &rules)) ++ *offload_trigger |= QCA808X_LED_SPEED10_ON; ++ if (test_bit(TRIGGER_NETDEV_LINK_100, &rules)) ++ *offload_trigger |= QCA808X_LED_SPEED100_ON; ++ if (test_bit(TRIGGER_NETDEV_LINK_1000, &rules)) ++ *offload_trigger |= QCA808X_LED_SPEED1000_ON; ++ if (test_bit(TRIGGER_NETDEV_LINK_2500, &rules)) ++ *offload_trigger |= QCA808X_LED_SPEED2500_ON; ++ if (test_bit(TRIGGER_NETDEV_HALF_DUPLEX, &rules)) ++ *offload_trigger |= QCA808X_LED_HALF_DUPLEX_ON; ++ if (test_bit(TRIGGER_NETDEV_FULL_DUPLEX, &rules)) ++ *offload_trigger |= QCA808X_LED_FULL_DUPLEX_ON; ++ ++ if (rules && !*offload_trigger) ++ return -EOPNOTSUPP; ++ ++ /* Enable BLINK_CHECK_BYPASS by default to make the LED ++ * blink even with duplex or speed mode not enabled. ++ */ ++ *offload_trigger |= QCA808X_LED_BLINK_CHECK_BYPASS; ++ ++ return 0; ++} ++ ++static int qca808x_led_hw_control_enable(struct phy_device *phydev, u8 index) ++{ ++ u16 reg; ++ ++ if (index > 2) ++ return -EINVAL; ++ ++ reg = QCA808X_MMD7_LED_FORCE_CTRL(index); ++ ++ return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg, ++ QCA808X_LED_FORCE_EN); ++} ++ ++static int qca808x_led_hw_is_supported(struct phy_device *phydev, u8 index, ++ unsigned long rules) ++{ ++ u16 offload_trigger = 0; ++ ++ if (index > 2) ++ return -EINVAL; ++ ++ return qca808x_led_parse_netdev(phydev, rules, &offload_trigger); ++} ++ ++static int qca808x_led_hw_control_set(struct phy_device *phydev, u8 index, ++ unsigned long rules) ++{ ++ u16 reg, offload_trigger = 0; ++ int ret; ++ ++ if (index > 2) ++ return -EINVAL; ++ ++ reg = QCA808X_MMD7_LED_CTRL(index); ++ ++ ret = qca808x_led_parse_netdev(phydev, rules, &offload_trigger); ++ if (ret) ++ return ret; ++ ++ ret = qca808x_led_hw_control_enable(phydev, index); ++ if (ret) ++ return ret; ++ ++ return phy_modify_mmd(phydev, MDIO_MMD_AN, reg, ++ QCA808X_LED_PATTERN_MASK, ++ offload_trigger); ++} ++ ++static bool qca808x_led_hw_control_status(struct phy_device *phydev, u8 index) ++{ ++ u16 reg; ++ int val; ++ ++ if (index > 2) ++ return false; ++ ++ reg = QCA808X_MMD7_LED_FORCE_CTRL(index); ++ ++ val = phy_read_mmd(phydev, MDIO_MMD_AN, reg); ++ ++ return !(val & QCA808X_LED_FORCE_EN); ++} ++ ++static int qca808x_led_hw_control_get(struct phy_device *phydev, u8 index, ++ unsigned long *rules) ++{ ++ u16 reg; ++ int val; ++ ++ if (index > 2) ++ return -EINVAL; ++ ++ /* Check if we have hw control enabled */ ++ if (qca808x_led_hw_control_status(phydev, index)) ++ return -EINVAL; ++ ++ reg = QCA808X_MMD7_LED_CTRL(index); ++ ++ val = phy_read_mmd(phydev, MDIO_MMD_AN, reg); ++ if (val & QCA808X_LED_TX_BLINK) ++ set_bit(TRIGGER_NETDEV_TX, rules); ++ if (val & QCA808X_LED_RX_BLINK) ++ set_bit(TRIGGER_NETDEV_RX, rules); ++ if (val & QCA808X_LED_SPEED10_ON) ++ set_bit(TRIGGER_NETDEV_LINK_10, rules); ++ if (val & QCA808X_LED_SPEED100_ON) ++ set_bit(TRIGGER_NETDEV_LINK_100, rules); ++ if (val & QCA808X_LED_SPEED1000_ON) ++ set_bit(TRIGGER_NETDEV_LINK_1000, rules); ++ if (val & QCA808X_LED_SPEED2500_ON) ++ set_bit(TRIGGER_NETDEV_LINK_2500, rules); ++ if (val & QCA808X_LED_HALF_DUPLEX_ON) ++ set_bit(TRIGGER_NETDEV_HALF_DUPLEX, rules); ++ if (val & QCA808X_LED_FULL_DUPLEX_ON) ++ set_bit(TRIGGER_NETDEV_FULL_DUPLEX, rules); ++ ++ return 0; ++} ++ ++static int qca808x_led_hw_control_reset(struct phy_device *phydev, u8 index) ++{ ++ u16 reg; ++ ++ if (index > 2) ++ return -EINVAL; ++ ++ reg = QCA808X_MMD7_LED_CTRL(index); ++ ++ return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg, ++ QCA808X_LED_PATTERN_MASK); ++} ++ ++static int qca808x_led_brightness_set(struct phy_device *phydev, ++ u8 index, enum led_brightness value) ++{ ++ u16 reg; ++ int ret; ++ ++ if (index > 2) ++ return -EINVAL; ++ ++ if (!value) { ++ ret = qca808x_led_hw_control_reset(phydev, index); ++ if (ret) ++ return ret; ++ } ++ ++ reg = QCA808X_MMD7_LED_FORCE_CTRL(index); ++ ++ return phy_modify_mmd(phydev, MDIO_MMD_AN, reg, ++ QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_MODE_MASK, ++ QCA808X_LED_FORCE_EN | value ? QCA808X_LED_FORCE_ON : ++ QCA808X_LED_FORCE_OFF); ++} ++ ++static int qca808x_led_blink_set(struct phy_device *phydev, u8 index, ++ unsigned long *delay_on, ++ unsigned long *delay_off) ++{ ++ int ret; ++ u16 reg; ++ ++ if (index > 2) ++ return -EINVAL; ++ ++ reg = QCA808X_MMD7_LED_FORCE_CTRL(index); ++ ++ /* Set blink to 50% off, 50% on at 4Hz by default */ ++ ret = phy_modify_mmd(phydev, MDIO_MMD_AN, QCA808X_MMD7_LED_GLOBAL, ++ QCA808X_LED_BLINK_FREQ_MASK | QCA808X_LED_BLINK_DUTY_MASK, ++ QCA808X_LED_BLINK_FREQ_4HZ | QCA808X_LED_BLINK_DUTY_50_50); ++ if (ret) ++ return ret; ++ ++ /* We use BLINK_1 for normal blinking */ ++ ret = phy_modify_mmd(phydev, MDIO_MMD_AN, reg, ++ QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_MODE_MASK, ++ QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_BLINK_1); ++ if (ret) ++ return ret; ++ ++ /* We set blink to 4Hz, aka 250ms */ ++ *delay_on = 250 / 2; ++ *delay_off = 250 / 2; ++ ++ return 0; ++} ++ ++static int qca808x_led_polarity_set(struct phy_device *phydev, int index, ++ unsigned long modes) ++{ ++ struct at803x_priv *priv = phydev->priv; ++ bool active_low = false; ++ u32 mode; ++ ++ for_each_set_bit(mode, &modes, __PHY_LED_MODES_NUM) { ++ switch (mode) { ++ case PHY_LED_ACTIVE_LOW: ++ active_low = true; ++ break; ++ default: ++ return -EINVAL; ++ } ++ } ++ ++ /* PHY polarity is global and can't be set per LED. ++ * To detect this, check if last requested polarity mode ++ * match the new one. ++ */ ++ if (priv->led_polarity_mode >= 0 && ++ priv->led_polarity_mode != active_low) { ++ phydev_err(phydev, "PHY polarity is global. Mismatched polarity on different LED\n"); ++ return -EINVAL; ++ } ++ ++ /* Save the last PHY polarity mode */ ++ priv->led_polarity_mode = active_low; ++ ++ return phy_modify_mmd(phydev, MDIO_MMD_AN, ++ QCA808X_MMD7_LED_POLARITY_CTRL, ++ QCA808X_LED_ACTIVE_HIGH, ++ active_low ? 0 : QCA808X_LED_ACTIVE_HIGH); ++} ++ + static struct phy_driver at803x_driver[] = { + { + /* Qualcomm Atheros AR8035 */ +@@ -2411,6 +2732,12 @@ static struct phy_driver at803x_driver[] + .cable_test_start = qca808x_cable_test_start, + .cable_test_get_status = qca808x_cable_test_get_status, + .link_change_notify = qca808x_link_change_notify, ++ .led_brightness_set = qca808x_led_brightness_set, ++ .led_blink_set = qca808x_led_blink_set, ++ .led_hw_is_supported = qca808x_led_hw_is_supported, ++ .led_hw_control_set = qca808x_led_hw_control_set, ++ .led_hw_control_get = qca808x_led_hw_control_get, ++ .led_polarity_set = qca808x_led_polarity_set, + }, }; + + module_phy_driver(at803x_driver); diff --git a/target/linux/generic/backport-6.1/835-v6.9-net-phy-add-support-for-PHY-LEDs-polarity-modes.patch b/target/linux/generic/backport-6.1/835-v6.9-net-phy-add-support-for-PHY-LEDs-polarity-modes.patch new file mode 100644 index 0000000000..604b3db270 --- /dev/null +++ b/target/linux/generic/backport-6.1/835-v6.9-net-phy-add-support-for-PHY-LEDs-polarity-modes.patch @@ -0,0 +1,98 @@ +From 7ae215ee7bb855f13c80565470fc7f67db4ba82f Mon Sep 17 00:00:00 2001 +From: Christian Marangi +Date: Thu, 25 Jan 2024 21:36:59 +0100 +Subject: [PATCH 3/5] net: phy: add support for PHY LEDs polarity modes + +Add support for PHY LEDs polarity modes. Some PHY require LED to be set +to active low to be turned ON. Adds support for this by declaring +active-low property in DT. + +PHY driver needs to declare .led_polarity_set() to configure LED +polarity modes. Function will pass the index with the LED index and a +bitmap with all the required modes to set. + +Current supported modes are: +- active-low with the flag PHY_LED_ACTIVE_LOW. LED is set to active-low + to turn it ON. +- inactive-high-impedance with the flag PHY_LED_INACTIVE_HIGH_IMPEDANCE. + LED is set to high impedance to turn it OFF. + +Signed-off-by: Christian Marangi +Reviewed-by: Andrew Lunn +Link: https://lore.kernel.org/r/20240125203702.4552-4-ansuelsmth@gmail.com +Signed-off-by: Jakub Kicinski +--- + drivers/net/phy/phy_device.c | 16 ++++++++++++++++ + include/linux/phy.h | 22 ++++++++++++++++++++++ + 2 files changed, 38 insertions(+) + +--- a/drivers/net/phy/phy_device.c ++++ b/drivers/net/phy/phy_device.c +@@ -3034,6 +3034,7 @@ static int of_phy_led(struct phy_device + struct device *dev = &phydev->mdio.dev; + struct led_init_data init_data = {}; + struct led_classdev *cdev; ++ unsigned long modes = 0; + struct phy_led *phyled; + u32 index; + int err; +@@ -3051,6 +3052,21 @@ static int of_phy_led(struct phy_device + if (index > U8_MAX) + return -EINVAL; + ++ if (of_property_read_bool(led, "active-low")) ++ set_bit(PHY_LED_ACTIVE_LOW, &modes); ++ if (of_property_read_bool(led, "inactive-high-impedance")) ++ set_bit(PHY_LED_INACTIVE_HIGH_IMPEDANCE, &modes); ++ ++ if (modes) { ++ /* Return error if asked to set polarity modes but not supported */ ++ if (!phydev->drv->led_polarity_set) ++ return -EINVAL; ++ ++ err = phydev->drv->led_polarity_set(phydev, index, modes); ++ if (err) ++ return err; ++ } ++ + phyled->index = index; + if (phydev->drv->led_brightness_set) + cdev->brightness_set_blocking = phy_led_set_brightness; +--- a/include/linux/phy.h ++++ b/include/linux/phy.h +@@ -787,6 +787,15 @@ struct phy_led { + + #define to_phy_led(d) container_of(d, struct phy_led, led_cdev) + ++/* Modes for PHY LED configuration */ ++enum phy_led_modes { ++ PHY_LED_ACTIVE_LOW = 0, ++ PHY_LED_INACTIVE_HIGH_IMPEDANCE = 1, ++ ++ /* keep it last */ ++ __PHY_LED_MODES_NUM, ++}; ++ + /** + * struct phy_driver - Driver structure for a particular PHY type + * +@@ -1055,6 +1064,19 @@ struct phy_driver { + int (*led_hw_control_get)(struct phy_device *dev, u8 index, + unsigned long *rules); + ++ /** ++ * @led_polarity_set: Set the LED polarity modes ++ * @dev: PHY device which has the LED ++ * @index: Which LED of the PHY device ++ * @modes: bitmap of LED polarity modes ++ * ++ * Configure LED with all the required polarity modes in @modes ++ * to make it correctly turn ON or OFF. ++ * ++ * Returns 0, or an error code. ++ */ ++ int (*led_polarity_set)(struct phy_device *dev, int index, ++ unsigned long modes); + }; + #define to_phy_driver(d) container_of(to_mdio_common_driver(d), \ + struct phy_driver, mdiodrv) diff --git a/target/linux/generic/pending-6.1/703-phy-add-detach-callback-to-struct-phy_driver.patch b/target/linux/generic/pending-6.1/703-phy-add-detach-callback-to-struct-phy_driver.patch index 425f82376b..aa852e7fec 100644 --- a/target/linux/generic/pending-6.1/703-phy-add-detach-callback-to-struct-phy_driver.patch +++ b/target/linux/generic/pending-6.1/703-phy-add-detach-callback-to-struct-phy_driver.patch @@ -23,7 +23,7 @@ Signed-off-by: Gabor Juhos sysfs_remove_link(&dev->dev.kobj, "phydev"); --- a/include/linux/phy.h +++ b/include/linux/phy.h -@@ -887,6 +887,12 @@ struct phy_driver { +@@ -896,6 +896,12 @@ struct phy_driver { /** @handle_interrupt: Override default interrupt handling */ irqreturn_t (*handle_interrupt)(struct phy_device *phydev);