From: Lea Teuberth Date: Tue, 2 Apr 2024 09:30:32 +0000 (+0200) Subject: ramips: add support for TP-Link Archer MR200v5 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=2a2f53415ed8ed79778edb8135bdbb5e819e587b;p=openwrt%2Fstaging%2Fneocturne.git ramips: add support for TP-Link Archer MR200v5 Specifications: CPU: MT7628AN 580MHz RAM: 64MB DDR2 FLASH: 8MB EN25QH64 NOR SPI WIFI: 2.4GHz 2x2 MT7628 b/g/n internal WIFI: 5GHz 1x1 MT7610E ac/n PCI LTE: Qualcomm MDM9207 ETH: 4xLAN 100base-T integrated SWITCH: RT3050-ESW Port 0,1,2,3: LAN, Port 6: CPU LEDS: LAN, WAN, Power, 3x signal strength, WiFi BTNS: Reset, WiFi toggle UART: Near ETH ports, Vcc-GND-RX-TX, 115200, 8N1 Installation: 1. Update using recovery mode - set your IP to 192.168.0.225, subnet mask: 255.255.255.0 - start tftp server, rename tftp-recovery.bin to tp_recovery.bin and place it into the server's directory - while holdig the "reset" button, power on the device - keep holding "reset" until the file is being transferred Notes: This board has only one MAC address programmed in the "romfile" partition: - MAC for phy0 (2.4GHz) at romfile 0xf100 (0) - MAC for phy1 (5GHz) at romfile 0xf100 (-1) - stock firmware re-uses phy0 MAC for ethernet - stock firmware uses romfile 0xf100 (1) for WWAN; not used since QMI interface is raw IP Signed-off-by: Lea Teuberth --- diff --git a/target/linux/ramips/dts/mt7628an_tplink_archer-mr200-v5.dts b/target/linux/ramips/dts/mt7628an_tplink_archer-mr200-v5.dts new file mode 100644 index 0000000000..177cd4db8a --- /dev/null +++ b/target/linux/ramips/dts/mt7628an_tplink_archer-mr200-v5.dts @@ -0,0 +1,192 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7628an.dtsi" + +#include +#include +#include + +/ { + compatible = "tplink,archer-mr200-v5", "mediatek,mt7628an-soc"; + model = "TP-Link Archer MR200 v5"; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + label-mac-device = ðernet; + }; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + leds { + compatible = "gpio-leds"; + + lan { + function = LED_FUNCTION_LAN; + color = ; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + + wan { + function = LED_FUNCTION_WAN; + color = ; + gpios = <&gpio 40 GPIO_ACTIVE_LOW>; + }; + + led_power: power { + function = LED_FUNCTION_POWER; + color = ; + gpios = <&gpio 39 GPIO_ACTIVE_LOW>; + }; + + signal1 { + label = "white:signal1"; + gpios = <&gpio 41 GPIO_ACTIVE_LOW>; + }; + + signal2 { + label = "white:signal2"; + gpios = <&gpio 42 GPIO_ACTIVE_LOW>; + }; + + signal3 { + label = "white:signal3"; + gpios = <&gpio 43 GPIO_ACTIVE_LOW>; + }; + + wlan { + function = LED_FUNCTION_WLAN; + color = ; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio 38 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + rfkill { + label = "rfkill"; + gpios = <&gpio 46 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <104000000>; + m25p,fast-read; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x20000>; + read-only; + }; + + partition@20000 { + compatible = "tplink,firmware"; + label = "firmware"; + reg = <0x20000 0x7b0000>; + }; + + partition@7d0000 { + label = "config"; + reg = <0x7d0000 0x10000>; + read-only; + }; + + partition@7e0000 { + label = "romfile"; + reg = <0x7e0000 0x10000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_romfile_f100: macaddr@f100 { + compatible = "mac-base"; + reg = <0xf100 0x6>; + #nvmem-cell-cells = <1>; + }; + }; + }; + + partition@7f0000 { + label = "radio"; + reg = <0x7f0000 0x10000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + eeprom_radio_0: eeprom@0 { + reg = <0x0 0x400>; + }; + + eeprom_radio_8000: eeprom@8000 { + reg = <0x8000 0x200>; + }; + }; + }; + }; + }; +}; + +&state_default { + gpio { + groups = "i2c", "p0led_an", "p1led_an", "p2led_an", "p3led_an", "p4led_an", "uart1", "wdt"; + function = "gpio"; + }; +}; + +&wmac { + nvmem-cells = <&eeprom_radio_0>, <&macaddr_romfile_f100 0>; + nvmem-cell-names = "eeprom", "mac-address"; + status = "okay"; +}; + +&esw { + mediatek,portdisable = <0x30>; +}; + +ðernet { + nvmem-cells = <&macaddr_romfile_f100 0>; + nvmem-cell-names = "mac-address"; +}; + +&pcie { + status = "okay"; +}; + +&pcie0 { + mt76@0,0 { + reg = <0x0000 0 0 0 0>; + ieee80211-freq-limit = <5000000 6000000>; + nvmem-cells = <&eeprom_radio_8000>, <&macaddr_romfile_f100 (-1)>; + nvmem-cell-names = "eeprom", "mac-address"; + }; +}; diff --git a/target/linux/ramips/image/mt76x8.mk b/target/linux/ramips/image/mt76x8.mk index fc81266da9..37c5a034c4 100644 --- a/target/linux/ramips/image/mt76x8.mk +++ b/target/linux/ramips/image/mt76x8.mk @@ -606,6 +606,21 @@ define Device/tplink_archer-c50-v6 endef TARGET_DEVICES += tplink_archer-c50-v6 +define Device/tplink_archer-mr200-v5 + $(Device/tplink-v2) + IMAGE_SIZE := 7872k + DEVICE_MODEL := Archer MR200 + DEVICE_VARIANT := v5 + TPLINK_FLASHLAYOUT := 8MLmtk + TPLINK_HWID := 0x20000005 + TPLINK_HWREV := 0x5 + TPLINK_HWREVADD := 0x5 + DEVICE_PACKAGES := kmod-mt76x0e uqmi kmod-usb2 kmod-usb-serial-option + IMAGES := sysupgrade.bin tftp-recovery.bin + IMAGE/tftp-recovery.bin := pad-extra 128k | $$(IMAGE/factory.bin) +endef +TARGET_DEVICES += tplink_archer-mr200-v5 + define Device/tplink_re200-v2 $(Device/tplink-safeloader) IMAGE_SIZE := 7808k diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds index da3ef154c0..324b57124f 100644 --- a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds @@ -83,6 +83,10 @@ tplink,archer-c50-v6) ucidef_set_led_wlan "wlan2g" "wlan2g" "green:wlan2g" "phy0tpt" ucidef_set_led_wlan "wlan5g" "wlan5g" "green:wlan5g" "phy1tpt" ;; +tplink,archer-mr200-v5) + ucidef_set_led_netdev "lan" "lan" "white:lan" "eth0" + ucidef_set_led_netdev "wan" "wan" "white:wan" "wwan0" + ;; tplink,re200-v2|\ tplink,re200-v3|\ tplink,re200-v4|\ diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network index fd8c086a85..9fee26e122 100644 --- a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network @@ -153,6 +153,11 @@ ramips_setup_interfaces() ucidef_add_switch "switch0" \ "0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "6t@eth0" ;; + tplink,archer-mr200-v5) + ucidef_add_switch "switch0" \ + "0:lan" "1:lan" "2:lan" "3:lan" "6t@eth0" + ucidef_set_interface "wan" device "/dev/cdc-wdm0" protocol "qmi" + ;; tplink,tl-mr3020-v3) ucidef_add_switch "switch0" \ "0:lan" "6@eth0"