From: Adrian Schmutzler Date: Mon, 19 Oct 2020 13:37:54 +0000 (+0200) Subject: ipq806x: remove support for kernel 4.19 X-Git-Tag: v21.02.0-rc1~1321 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=29ca10e537ee;p=openwrt%2Fstaging%2Fchunkeey.git ipq806x: remove support for kernel 4.19 The target uses 5.4 as default kernel since 04/2020. Kernel 4.19 support is not really maintained anymore, and there has been a lot of changes between 4.19 and 5.4 on this target. Despite, new devices are typically added for 5.4 only anyway. Thus, make maintaining of old stuff and reviewing of new stuff easier by removing support for kernel 4.19. Signed-off-by: Adrian Schmutzler --- diff --git a/target/linux/ipq806x/config-4.19 b/target/linux/ipq806x/config-4.19 deleted file mode 100644 index b21254ed08..0000000000 --- a/target/linux/ipq806x/config-4.19 +++ /dev/null @@ -1,506 +0,0 @@ -CONFIG_ALIGNMENT_TRAP=y -# CONFIG_APQ_GCC_8084 is not set -# CONFIG_APQ_MMCC_8084 is not set -CONFIG_AR8216_PHY=y -CONFIG_ARCH_CLOCKSOURCE_DATA=y -CONFIG_ARCH_HAS_DEBUG_VIRTUAL=y -CONFIG_ARCH_HAS_ELF_RANDOMIZE=y -CONFIG_ARCH_HAS_FORTIFY_SOURCE=y -CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y -CONFIG_ARCH_HAS_KCOV=y -CONFIG_ARCH_HAS_MEMBARRIER_SYNC_CORE=y -CONFIG_ARCH_HAS_PHYS_TO_DMA=y -CONFIG_ARCH_HAS_SET_MEMORY=y -CONFIG_ARCH_HAS_SG_CHAIN=y -CONFIG_ARCH_HAS_STRICT_KERNEL_RWX=y -CONFIG_ARCH_HAS_STRICT_MODULE_RWX=y -CONFIG_ARCH_HAS_TICK_BROADCAST=y -CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y -CONFIG_ARCH_HIBERNATION_POSSIBLE=y -# CONFIG_ARCH_MDM9615 is not set -CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y -CONFIG_ARCH_MSM8960=y -CONFIG_ARCH_MSM8974=y -CONFIG_ARCH_MSM8X60=y -CONFIG_ARCH_MULTIPLATFORM=y -CONFIG_ARCH_MULTI_V6_V7=y -CONFIG_ARCH_MULTI_V7=y -CONFIG_ARCH_NR_GPIO=0 -CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y -CONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT=y -CONFIG_ARCH_QCOM=y -CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y -CONFIG_ARCH_SUPPORTS_BIG_ENDIAN=y -CONFIG_ARCH_SUPPORTS_UPROBES=y -CONFIG_ARCH_SUSPEND_POSSIBLE=y -CONFIG_ARCH_USE_BUILTIN_BSWAP=y -CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y -CONFIG_ARCH_WANT_GENERAL_HUGETLB=y -CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y -CONFIG_ARM=y -CONFIG_ARM_AMBA=y -CONFIG_ARM_APPENDED_DTB=y -CONFIG_ARM_ARCH_TIMER=y -CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y -CONFIG_ARM_ATAG_DTB_COMPAT=y -# CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND is not set -# CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER is not set -CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE=y -CONFIG_ARM_CPUIDLE=y -CONFIG_ARM_CPU_SUSPEND=y -# CONFIG_ARM_CPU_TOPOLOGY is not set -CONFIG_ARM_GIC=y -CONFIG_ARM_HAS_SG_CHAIN=y -CONFIG_ARM_L1_CACHE_SHIFT=6 -CONFIG_ARM_L1_CACHE_SHIFT_6=y -# CONFIG_ARM_LPAE is not set -CONFIG_ARM_PATCH_IDIV=y -CONFIG_ARM_PATCH_PHYS_VIRT=y -CONFIG_ARM_QCOM_CPUFREQ_NVMEM=y -CONFIG_ARM_QCOM_CPUIDLE=y -# CONFIG_ARM_SMMU is not set -# CONFIG_ARM_SP805_WATCHDOG is not set -CONFIG_ARM_THUMB=y -# CONFIG_ARM_THUMBEE is not set -CONFIG_ARM_UNWIND=y -CONFIG_ARM_VIRT_EXT=y -CONFIG_ARM_MODULE_PLTS=y -CONFIG_BLK_DEV_LOOP=y -CONFIG_BLK_MQ_PCI=y -CONFIG_BOUNCE=y -# CONFIG_CACHE_L2X0 is not set -CONFIG_CLKDEV_LOOKUP=y -CONFIG_CLKSRC_QCOM=y -CONFIG_CLONE_BACKWARDS=y -CONFIG_COMMON_CLK=y -CONFIG_COMMON_CLK_QCOM=y -CONFIG_CPUFREQ_DT=y -CONFIG_CPUFREQ_DT_PLATDEV=y -CONFIG_CPU_32v6K=y -CONFIG_CPU_32v7=y -CONFIG_CPU_ABRT_EV7=y -# CONFIG_CPU_BIG_ENDIAN is not set -# CONFIG_CPU_BPREDICT_DISABLE is not set -CONFIG_CPU_CACHE_V7=y -CONFIG_CPU_CACHE_VIPT=y -CONFIG_CPU_COPY_V6=y -CONFIG_CPU_CP15=y -CONFIG_CPU_CP15_MMU=y -CONFIG_CPU_FREQ=y -CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y -# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set -CONFIG_CPU_FREQ_GOV_ATTR_SET=y -CONFIG_CPU_FREQ_GOV_COMMON=y -# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set -CONFIG_CPU_FREQ_GOV_ONDEMAND=y -CONFIG_CPU_FREQ_GOV_PERFORMANCE=y -# CONFIG_CPU_FREQ_GOV_POWERSAVE is not set -# CONFIG_CPU_FREQ_GOV_USERSPACE is not set -CONFIG_CPU_FREQ_STAT=y -CONFIG_CPU_HAS_ASID=y -# CONFIG_CPU_ICACHE_DISABLE is not set -CONFIG_CPU_IDLE=y -CONFIG_CPU_IDLE_GOV_LADDER=y -CONFIG_CPU_IDLE_GOV_MENU=y -CONFIG_CPU_IDLE_MULTIPLE_DRIVERS=y -CONFIG_CPU_PABRT_V7=y -CONFIG_CPU_PM=y -CONFIG_CPU_RMAP=y -CONFIG_CPU_SPECTRE=y -CONFIG_CPU_THERMAL=y -CONFIG_CPU_THUMB_CAPABLE=y -CONFIG_CPU_TLB_V7=y -CONFIG_CPU_V7=y -CONFIG_CRC16=y -# CONFIG_CRC32_SARWATE is not set -CONFIG_CRC32_SLICEBY8=y -CONFIG_CRYPTO_ACOMP2=y -CONFIG_CRYPTO_AEAD=y -CONFIG_CRYPTO_AEAD2=y -CONFIG_CRYPTO_DEFLATE=y -CONFIG_CRYPTO_DEV_QCOM_RNG=y -CONFIG_CRYPTO_DRBG=y -CONFIG_CRYPTO_DRBG_HMAC=y -CONFIG_CRYPTO_DRBG_MENU=y -CONFIG_CRYPTO_HASH=y -CONFIG_CRYPTO_HASH2=y -CONFIG_CRYPTO_HMAC=y -CONFIG_CRYPTO_HW=y -CONFIG_CRYPTO_JITTERENTROPY=y -CONFIG_CRYPTO_LZO=y -CONFIG_CRYPTO_MANAGER=y -CONFIG_CRYPTO_MANAGER2=y -CONFIG_CRYPTO_NULL2=y -CONFIG_CRYPTO_RNG=y -CONFIG_CRYPTO_RNG2=y -CONFIG_CRYPTO_RNG_DEFAULT=y -CONFIG_CRYPTO_SHA256=y -CONFIG_CRYPTO_WORKQUEUE=y -CONFIG_DCACHE_WORD_ACCESS=y -CONFIG_DEBUG_GPIO=y -CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S" -# CONFIG_DEBUG_USER is not set -CONFIG_DMADEVICES=y -CONFIG_DMA_ENGINE=y -CONFIG_DMA_OF=y -CONFIG_DMA_VIRTUAL_CHANNELS=y -CONFIG_DTC=y -CONFIG_DT_IDLE_STATES=y -# CONFIG_DWMAC_DWC_QOS_ETH is not set -# CONFIG_DWMAC_GENERIC is not set -CONFIG_DWMAC_IPQ806X=y -CONFIG_DYNAMIC_DEBUG=y -CONFIG_EDAC_ATOMIC_SCRUB=y -CONFIG_EDAC_SUPPORT=y -CONFIG_ETHERNET_PACKET_MANGLE=y -CONFIG_FIXED_PHY=y -CONFIG_FIX_EARLYCON_MEM=y -CONFIG_GENERIC_ALLOCATOR=y -CONFIG_GENERIC_BUG=y -CONFIG_GENERIC_CLOCKEVENTS=y -CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y -CONFIG_GENERIC_CPU_AUTOPROBE=y -CONFIG_GENERIC_EARLY_IOREMAP=y -CONFIG_GENERIC_IDLE_POLL_SETUP=y -CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y -CONFIG_GENERIC_IRQ_MULTI_HANDLER=y -CONFIG_GENERIC_IRQ_SHOW=y -CONFIG_GENERIC_IRQ_SHOW_LEVEL=y -CONFIG_GENERIC_MSI_IRQ=y -CONFIG_GENERIC_MSI_IRQ_DOMAIN=y -CONFIG_GENERIC_PCI_IOMAP=y -CONFIG_GENERIC_PHY=y -CONFIG_GENERIC_PINCONF=y -CONFIG_GENERIC_PINCTRL_GROUPS=y -CONFIG_GENERIC_PINMUX_FUNCTIONS=y -CONFIG_GENERIC_SCHED_CLOCK=y -CONFIG_GENERIC_SMP_IDLE_THREAD=y -CONFIG_GENERIC_STRNCPY_FROM_USER=y -CONFIG_GENERIC_STRNLEN_USER=y -CONFIG_GENERIC_TIME_VSYSCALL=y -CONFIG_GPIOLIB=y -CONFIG_GPIOLIB_IRQCHIP=y -CONFIG_HANDLE_DOMAIN_IRQ=y -CONFIG_HARDEN_BRANCH_PREDICTOR=y -CONFIG_HARDIRQS_SW_RESEND=y -CONFIG_HAS_DMA=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT_MAP=y -CONFIG_HAVE_ARCH_AUDITSYSCALL=y -CONFIG_HAVE_ARCH_BITREVERSE=y -CONFIG_HAVE_ARCH_JUMP_LABEL=y -CONFIG_HAVE_ARCH_KGDB=y -CONFIG_HAVE_ARCH_PFN_VALID=y -CONFIG_HAVE_ARCH_SECCOMP_FILTER=y -CONFIG_HAVE_ARCH_THREAD_STRUCT_WHITELIST=y -CONFIG_HAVE_ARCH_TRACEHOOK=y -CONFIG_HAVE_ARM_ARCH_TIMER=y -CONFIG_HAVE_ARM_SMCCC=y -CONFIG_HAVE_CLK=y -CONFIG_HAVE_CLK_PREPARE=y -CONFIG_HAVE_CONTEXT_TRACKING=y -CONFIG_HAVE_C_RECORDMCOUNT=y -CONFIG_HAVE_DEBUG_KMEMLEAK=y -CONFIG_HAVE_DMA_CONTIGUOUS=y -CONFIG_HAVE_DYNAMIC_FTRACE=y -CONFIG_HAVE_DYNAMIC_FTRACE_WITH_REGS=y -CONFIG_HAVE_EBPF_JIT=y -CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y -CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y -CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y -CONFIG_HAVE_FUNCTION_TRACER=y -CONFIG_HAVE_GENERIC_DMA_COHERENT=y -CONFIG_HAVE_IDE=y -CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y -CONFIG_HAVE_LD_DEAD_CODE_DATA_ELIMINATION=y -CONFIG_HAVE_MEMBLOCK=y -CONFIG_HAVE_MOD_ARCH_SPECIFIC=y -CONFIG_HAVE_NET_DSA=y -CONFIG_HAVE_OPROFILE=y -CONFIG_HAVE_OPTPROBES=y -CONFIG_HAVE_PERF_EVENTS=y -CONFIG_HAVE_PERF_REGS=y -CONFIG_HAVE_PERF_USER_STACK_DUMP=y -CONFIG_HAVE_PROC_CPU=y -CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y -CONFIG_HAVE_RSEQ=y -CONFIG_HAVE_SMP=y -CONFIG_HAVE_SYSCALL_TRACEPOINTS=y -CONFIG_HAVE_UID16=y -CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y -CONFIG_HIGHMEM=y -# CONFIG_HIGHPTE is not set -CONFIG_HWMON=y -CONFIG_HWSPINLOCK=y -CONFIG_HWSPINLOCK_QCOM=y -CONFIG_HW_RANDOM=y -CONFIG_HZ_FIXED=0 -CONFIG_I2C=y -CONFIG_I2C_BOARDINFO=y -CONFIG_I2C_CHARDEV=y -CONFIG_I2C_HELPER_AUTO=y -CONFIG_I2C_QUP=y -CONFIG_INITRAMFS_SOURCE="" -# CONFIG_IOMMU_DEBUGFS is not set -# CONFIG_IOMMU_IO_PGTABLE_ARMV7S is not set -# CONFIG_IOMMU_IO_PGTABLE_LPAE is not set -CONFIG_IOMMU_SUPPORT=y -# CONFIG_IPQ_GCC_4019 is not set -CONFIG_IPQ_GCC_806X=y -# CONFIG_IPQ_GCC_8074 is not set -# CONFIG_IPQ_LCC_806X is not set -CONFIG_IRQCHIP=y -CONFIG_IRQ_DOMAIN=y -CONFIG_IRQ_DOMAIN_HIERARCHY=y -CONFIG_IRQ_FORCED_THREADING=y -CONFIG_IRQ_WORK=y -CONFIG_KPSS_XCC=y -CONFIG_KRAITCC=y -CONFIG_KRAIT_CLOCKS=y -CONFIG_KRAIT_L2_ACCESSORS=y -CONFIG_LEDS_TRIGGER_DISK=y -CONFIG_LIBFDT=y -CONFIG_LOCK_DEBUGGING_SUPPORT=y -CONFIG_LOCK_SPIN_ON_OWNER=y -CONFIG_LZO_COMPRESS=y -CONFIG_LZO_DECOMPRESS=y -CONFIG_MDIO_BITBANG=y -CONFIG_MDIO_BUS=y -CONFIG_MDIO_DEVICE=y -CONFIG_MDIO_GPIO=y -# CONFIG_MDM_GCC_9615 is not set -# CONFIG_MDM_LCC_9615 is not set -CONFIG_MEMFD_CREATE=y -CONFIG_MFD_QCOM_RPM=y -# CONFIG_MFD_SPMI_PMIC is not set -CONFIG_MFD_SYSCON=y -CONFIG_MIGHT_HAVE_CACHE_L2X0=y -CONFIG_MIGHT_HAVE_PCI=y -CONFIG_MIGRATION=y -CONFIG_MMC=y -CONFIG_MMC_ARMMMCI=y -CONFIG_MMC_BLOCK=y -CONFIG_MMC_BLOCK_MINORS=16 -CONFIG_MMC_QCOM_DML=y -CONFIG_MMC_SDHCI=y -CONFIG_MMC_SDHCI_IO_ACCESSORS=y -CONFIG_MMC_SDHCI_MSM=y -# CONFIG_MMC_SDHCI_PCI is not set -CONFIG_MMC_SDHCI_PLTFM=y -# CONFIG_MMC_TIFM_SD is not set -CONFIG_MODULES_USE_ELF_REL=y -# CONFIG_MSCC_OCELOT_SWITCH is not set -CONFIG_MSM_GCC_8660=y -# CONFIG_MSM_GCC_8916 is not set -# CONFIG_MSM_GCC_8960 is not set -# CONFIG_MSM_GCC_8974 is not set -# CONFIG_MSM_GCC_8994 is not set -# CONFIG_MSM_GCC_8996 is not set -# CONFIG_MSM_GCC_8998 is not set -# CONFIG_MSM_IOMMU is not set -# CONFIG_MSM_LCC_8960 is not set -# CONFIG_MSM_MMCC_8960 is not set -# CONFIG_MSM_MMCC_8974 is not set -# CONFIG_MSM_MMCC_8996 is not set -CONFIG_MTD_CMDLINE_PARTS=y -CONFIG_MTD_M25P80=y -CONFIG_MTD_NAND=y -CONFIG_MTD_NAND_ECC=y -CONFIG_MTD_NAND_QCOM=y -CONFIG_MTD_QCOM_SMEM_PARTS=y -CONFIG_MTD_SPI_NOR=y -CONFIG_MTD_SPLIT_FIRMWARE=y -CONFIG_MTD_SPLIT_FIT_FW=y -CONFIG_MTD_SPLIT_UIMAGE_FW=y -CONFIG_MTD_UBI=y -CONFIG_MTD_UBI_BEB_LIMIT=20 -CONFIG_MTD_UBI_BLOCK=y -# CONFIG_MTD_UBI_FASTMAP is not set -# CONFIG_MTD_UBI_GLUEBI is not set -CONFIG_MTD_UBI_WL_THRESHOLD=4096 -CONFIG_MUTEX_SPIN_ON_OWNER=y -CONFIG_NEED_DMA_MAP_STATE=y -CONFIG_NEON=y -CONFIG_NET_DSA=y -CONFIG_NET_DSA_HWMON=y -CONFIG_NET_DSA_QCA8K=y -CONFIG_NET_DSA_TAG_QCA=y -# CONFIG_NET_DSA_VITESSE_VSC73XX is not set -CONFIG_NET_FLOW_LIMIT=y -CONFIG_NET_PTP_CLASSIFY=y -CONFIG_NET_SWITCHDEV=y -CONFIG_NLS=y -CONFIG_NO_BOOTMEM=y -CONFIG_NO_HZ=y -CONFIG_NO_HZ_COMMON=y -CONFIG_NO_HZ_IDLE=y -CONFIG_NR_CPUS=2 -CONFIG_NVMEM=y -CONFIG_OF=y -CONFIG_OF_ADDRESS=y -CONFIG_OF_EARLY_FLATTREE=y -CONFIG_OF_FLATTREE=y -CONFIG_OF_GPIO=y -CONFIG_OF_IRQ=y -CONFIG_OF_KOBJ=y -CONFIG_OF_MDIO=y -CONFIG_OF_NET=y -CONFIG_OF_RESERVED_MEM=y -CONFIG_OLD_SIGACTION=y -CONFIG_OLD_SIGSUSPEND3=y -CONFIG_PADATA=y -CONFIG_PAGE_OFFSET=0xC0000000 -CONFIG_PCI=y -# CONFIG_PCI_V3_SEMI is not set -CONFIG_PCIEAER=y -CONFIG_PCIEPORTBUS=y -CONFIG_PCIE_DW=y -CONFIG_PCIE_DW_HOST=y -CONFIG_PCIE_QCOM=y -CONFIG_PCI_DEBUG=y -CONFIG_PCI_DISABLE_COMMON_QUIRKS=y -CONFIG_PCI_DOMAINS=y -CONFIG_PCI_DOMAINS_GENERIC=y -CONFIG_PCI_MSI=y -CONFIG_PCI_MSI_IRQ_DOMAIN=y -CONFIG_PERF_USE_VMALLOC=y -CONFIG_PGTABLE_LEVELS=2 -CONFIG_PHYLIB=y -CONFIG_PHYLINK=y -# CONFIG_PHY_QCOM_APQ8064_SATA is not set -# CONFIG_PHY_QCOM_DWC3 is not set -CONFIG_PHY_QCOM_IPQ806X_SATA=y -# CONFIG_PHY_QCOM_QMP is not set -# CONFIG_PHY_QCOM_QUSB2 is not set -# CONFIG_PHY_QCOM_UFS is not set -CONFIG_PINCTRL=y -# CONFIG_PINCTRL_APQ8064 is not set -# CONFIG_PINCTRL_APQ8084 is not set -# CONFIG_PINCTRL_IPQ4019 is not set -CONFIG_PINCTRL_IPQ8064=y -# CONFIG_PINCTRL_IPQ8074 is not set -# CONFIG_PINCTRL_MDM9615 is not set -CONFIG_PINCTRL_MSM=y -# CONFIG_PINCTRL_MSM8660 is not set -# CONFIG_PINCTRL_MSM8916 is not set -# CONFIG_PINCTRL_MSM8960 is not set -# CONFIG_PINCTRL_MSM8994 is not set -# CONFIG_PINCTRL_MSM8996 is not set -# CONFIG_PINCTRL_MSM8998 is not set -# CONFIG_PINCTRL_QCOM_SPMI_PMIC is not set -# CONFIG_PINCTRL_QCOM_SSBI_PMIC is not set -# CONFIG_PINCTRL_SDM845 is not set -CONFIG_PLUGIN_HOSTCC="g++" -CONFIG_PM_OPP=y -CONFIG_POWER_RESET=y -CONFIG_POWER_RESET_MSM=y -CONFIG_POWER_SUPPLY=y -CONFIG_PPS=y -CONFIG_PRINTK_TIME=y -CONFIG_PTP_1588_CLOCK=y -# CONFIG_QCOM_A53PLL is not set -CONFIG_QCOM_ADM=y -CONFIG_QCOM_BAM_DMA=y -CONFIG_QCOM_CLK_RPM=y -# CONFIG_QCOM_COMMAND_DB is not set -# CONFIG_QCOM_EBI2 is not set -# CONFIG_QCOM_GENI_SE is not set -CONFIG_QCOM_GSBI=y -CONFIG_QCOM_HFPLL=y -# CONFIG_QCOM_IOMMU is not set -# CONFIG_QCOM_LLCC is not set -# CONFIG_QCOM_PDC is not set -CONFIG_QCOM_PM=y -CONFIG_QCOM_QFPROM=y -# CONFIG_QCOM_RMTFS_MEM is not set -CONFIG_QCOM_RPMCC=y -CONFIG_QCOM_SCM=y -CONFIG_QCOM_SCM_32=y -# CONFIG_QCOM_SCM_DOWNLOAD_MODE_DEFAULT is not set -CONFIG_QCOM_SMEM=y -# CONFIG_QCOM_SMSM is not set -CONFIG_QCOM_TCSR=y -CONFIG_QCOM_TSENS=y -CONFIG_QCOM_WDT=y -# CONFIG_QRTR is not set -CONFIG_RAS=y -CONFIG_RATIONAL=y -CONFIG_RCU_CPU_STALL_TIMEOUT=21 -CONFIG_RCU_NEED_SEGCBLIST=y -CONFIG_RCU_STALL_COMMON=y -CONFIG_REFCOUNT_FULL=y -CONFIG_REGMAP=y -CONFIG_REGMAP_I2C=y -CONFIG_REGMAP_MMIO=y -CONFIG_REGMAP_SPI=y -CONFIG_REGULATOR=y -CONFIG_REGULATOR_FIXED_VOLTAGE=y -CONFIG_REGULATOR_QCOM_RPM=y -# CONFIG_REGULATOR_QCOM_SPMI is not set -CONFIG_RESET_CONTROLLER=y -# CONFIG_RESET_QCOM_AOSS is not set -CONFIG_RFS_ACCEL=y -CONFIG_RPS=y -CONFIG_RTC_CLASS=y -# CONFIG_RTC_DRV_CMOS is not set -CONFIG_RTC_I2C_AND_SPI=y -CONFIG_RWSEM_SPIN_ON_OWNER=y -CONFIG_RWSEM_XCHGADD_ALGORITHM=y -# CONFIG_SDM_DISPCC_845 is not set -# CONFIG_SDM_GCC_845 is not set -# CONFIG_SDM_VIDEOCC_845 is not set -CONFIG_SERIAL_8250_FSL=y -# CONFIG_SERIAL_AMBA_PL011 is not set -CONFIG_SERIAL_MSM=y -CONFIG_SERIAL_MSM_CONSOLE=y -CONFIG_SGL_ALLOC=y -CONFIG_SMP=y -CONFIG_SMP_ON_UP=y -CONFIG_SPARSE_IRQ=y -CONFIG_SPI=y -CONFIG_SPI_MASTER=y -CONFIG_SPI_MEM=y -CONFIG_SPI_QUP=y -CONFIG_SPMI=y -CONFIG_SPMI_MSM_PMIC_ARB=y -# CONFIG_SPMI_PMIC_CLKDIV is not set -CONFIG_SRCU=y -CONFIG_STMMAC_ETH=y -CONFIG_STMMAC_PLATFORM=y -CONFIG_SWCONFIG=y -CONFIG_SWCONFIG_LEDS=y -CONFIG_SWPHY=y -CONFIG_SWP_EMULATE=y -CONFIG_SYS_SUPPORTS_APM_EMULATION=y -CONFIG_THERMAL=y -CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y -CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0 -CONFIG_THERMAL_GOV_STEP_WISE=y -CONFIG_THERMAL_HWMON=y -CONFIG_THERMAL_OF=y -# CONFIG_THUMB2_KERNEL is not set -CONFIG_TICK_CPU_ACCOUNTING=y -CONFIG_TIMER_OF=y -CONFIG_TIMER_PROBE=y -CONFIG_TREE_RCU=y -CONFIG_TREE_SRCU=y -CONFIG_UBIFS_FS=y -CONFIG_UBIFS_FS_ADVANCED_COMPR=y -CONFIG_UBIFS_FS_LZO=y -CONFIG_UBIFS_FS_ZLIB=y -CONFIG_UEVENT_HELPER_PATH="" -CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h" -CONFIG_USB=y -CONFIG_USB_COMMON=y -CONFIG_USB_SUPPORT=y -CONFIG_USE_OF=y -CONFIG_VFP=y -CONFIG_VFPv3=y -CONFIG_WATCHDOG_CORE=y -CONFIG_XPS=y -CONFIG_XZ_DEC_ARM=y -CONFIG_XZ_DEC_BCJ=y -CONFIG_ZBOOT_ROM_BSS=0 -CONFIG_ZBOOT_ROM_TEXT=0 -CONFIG_ZLIB_DEFLATE=y -CONFIG_ZLIB_INFLATE=y diff --git a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-ap148.dts b/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-ap148.dts deleted file mode 100644 index 02f60c90ee..0000000000 --- a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-ap148.dts +++ /dev/null @@ -1,229 +0,0 @@ -#include "qcom-ipq8064-v1.0.dtsi" - -/ { - model = "Qualcomm Technologies, Inc. IPQ8064/AP-148"; - compatible = "qcom,ipq8064-ap148", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - mdio-gpio0 = &mdio0; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - soc { - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, - <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - }; - }; - }; -}; - -&qcom_pinmux { - i2c4_pins: i2c4_pinmux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - bias-disable; - }; - - nand_pins: nand_pins { - disable { - pins = "gpio34", "gpio35", "gpio36", - "gpio37", "gpio38"; - function = "nand"; - drive-strength = <10>; - bias-disable; - }; - - pullups { - pins = "gpio39"; - function = "nand"; - drive-strength = <10>; - bias-pull-up; - }; - - hold { - pins = "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - function = "nand"; - drive-strength = <10>; - bias-bus-hold; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - }; -}; - -&adm_dma { - status = "okay"; -}; - -&gsbi4 { - qcom,mode = ; - status = "okay"; - - serial@16340000 { - status = "okay"; - }; - - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ -}; - -&gsbi5 { - qcom,mode = ; - status = "okay"; - - spi4: spi@1a280000 { - status = "okay"; - spi-max-frequency = <50000000>; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 0>; - - flash: m25p80@0 { - compatible = "s25fl256s1"; - #address-cells = <1>; - #size-cells = <1>; - spi-max-frequency = <50000000>; - reg = <0>; - - partitions { - compatible = "qcom,smem"; - }; - }; - }; -}; - -&usb3_0 { - status = "okay"; -}; - -&usb3_1 { - status = "okay"; -}; - -&pcie0 { - status = "okay"; -}; - -&pcie1 { - status = "okay"; - force_gen1 = <1>; -}; - -&nand { - status = "okay"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - cs0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "qcom,smem"; - }; - }; -}; - -&gmac1 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gmac2 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&sata_phy { - status = "okay"; -}; - -&sata { - status = "okay"; -}; diff --git a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-ap161.dts b/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-ap161.dts deleted file mode 100644 index de347643dc..0000000000 --- a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-ap161.dts +++ /dev/null @@ -1,264 +0,0 @@ -#include "qcom-ipq8064-v1.0.dtsi" - -/ { - model = "Qualcomm IPQ8064/AP161"; - compatible = "qcom,ipq8064-ap161", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - mdio-gpio0 = &mdio0; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - soc { - pinmux@800000 { - i2c4_pins: i2c4_pinmux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - bias-disable; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - drive-strength = <10>; - bias-none; - }; - }; - nand_pins: nand_pins { - disable { - pins = "gpio34", "gpio35", "gpio36", - "gpio37", "gpio38"; - function = "nand"; - drive-strength = <10>; - bias-disable; - }; - - pullups { - pins = "gpio39"; - function = "nand"; - drive-strength = <10>; - bias-pull-up; - }; - - hold { - pins = "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - function = "nand"; - drive-strength = <10>; - bias-bus-hold; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio2", "gpio27", "gpio28", - "gpio29", "gpio30", "gpio31", - "gpio32", "gpio51", "gpio52", - "gpio59", "gpio60", "gpio61", - "gpio62" , "gpio66"; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - }; - }; - - gsbi@16300000 { - qcom,mode = ; - status = "okay"; - serial@16340000 { - status = "okay"; - }; - - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ - }; - - gsbi5: gsbi@1a200000 { - qcom,mode = ; - status = "okay"; - - spi4: spi@1a280000 { - status = "okay"; - spi-max-frequency = <50000000>; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 0>; - - flash: m25p80@0 { - compatible = "s25fl256s1"; - #address-cells = <1>; - #size-cells = <1>; - spi-max-frequency = <50000000>; - reg = <0>; - - partitions { - compatible = "qcom,smem"; - }; - }; - }; - }; - - sata-phy@1b400000 { - status = "okay"; - }; - - sata@29000000 { - status = "okay"; - }; - - usb3_0: usb3@110f8800 { - status = "okay"; - }; - - usb3_1: usb3@100f8800 { - status = "okay"; - }; - - pcie0: pci@1b500000 { - status = "okay"; - }; - - pcie1: pci@1b700000 { - status = "okay"; - force_gen1 = <1>; - }; - - pcie2: pci@1b900000 { - status = "okay"; - }; - - nand@1ac00000 { - status = "okay"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - cs0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "qcom,smem"; - }; - }; - }; - - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x20080 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - qca,phy-rgmii-en; - qca,txclk-delay-en; - qca,rxclk-delay-en; - }; - - phy3: ethernet-phy@3 { - device_type = "ethernet-phy"; - reg = <3>; - }; - }; - - gmac0: ethernet@37000000 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <0>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - mdiobus = <&mdio0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - gmac1: ethernet@37200000 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <1>; - mdiobus = <&mdio0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - gmac2: ethernet@37400000 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - mdiobus = <&mdio0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; -}; - -&adm_dma { - status = "okay"; -}; diff --git a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-c2600.dts b/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-c2600.dts deleted file mode 100644 index 027500f038..0000000000 --- a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-c2600.dts +++ /dev/null @@ -1,479 +0,0 @@ -#include "qcom-ipq8064-v2.0.dtsi" - -#include - -/ { - model = "TP-Link Archer C2600"; - compatible = "tplink,c2600", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - mdio-gpio0 = &mdio0; - - led-boot = &power; - led-failsafe = &general; - led-running = &power; - led-upgrade = &general; - label-mac-device = &gmac2; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - soc { - pinmux@800000 { - button_pins: button_pins { - mux { - pins = "gpio16", "gpio54", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - i2c4_pins: i2c4_pinmux { - mux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - drive-strength = <12>; - bias-disable; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio26", "gpio33", - "gpio53", "gpio66"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - bias-pull-down; - }; - - data { - pins = "gpio18", "gpio19"; - drive-strength = <10>; - }; - - cs { - pins = "gpio20"; - function = "gpio"; - drive-strength = <10>; - bias-pull-up; - }; - - clk { - pins = "gpio21"; - drive-strength = <12>; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - }; - - usb0_pwr_en_pin: usb0_pwr_en_pin { - mux { - pins = "gpio25"; - function = "gpio"; - drive-strength = <10>; - bias-pull-up; - output-high; - }; - }; - - usb1_pwr_en_pin: usb1_pwr_en_pin { - mux { - pins = "gpio23"; - function = "gpio"; - drive-strength = <10>; - bias-pull-up; - output-high; - }; - }; - }; - - gsbi@16300000 { - qcom,mode = ; - status = "okay"; - serial@16340000 { - status = "okay"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ - }; - - gsbi5: gsbi@1a200000 { - qcom,mode = ; - status = "okay"; - - spi5: spi@1a280000 { - status = "okay"; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; - - flash: m25p80@0 { - compatible = "jedec,spi-nor"; - #address-cells = <1>; - #size-cells = <1>; - spi-max-frequency = <50000000>; - reg = <0>; - - SBL1@0 { - label = "SBL1"; - reg = <0x0 0x20000>; - read-only; - }; - - MIBIB@20000 { - label = "MIBIB"; - reg = <0x20000 0x20000>; - read-only; - }; - - SBL2@40000 { - label = "SBL2"; - reg = <0x40000 0x20000>; - read-only; - }; - - SBL3@60000 { - label = "SBL3"; - reg = <0x60000 0x30000>; - read-only; - }; - - DDRCONFIG@90000 { - label = "DDRCONFIG"; - reg = <0x90000 0x10000>; - read-only; - }; - - SSD@a0000 { - label = "SSD"; - reg = <0xa0000 0x10000>; - read-only; - }; - - TZ@b0000 { - label = "TZ"; - reg = <0xb0000 0x30000>; - read-only; - }; - - RPM@e0000 { - label = "RPM"; - reg = <0xe0000 0x20000>; - read-only; - }; - - fs-uboot@100000 { - label = "fs-uboot"; - reg = <0x100000 0x70000>; - read-only; - }; - - uboot-env@170000 { - label = "uboot-env"; - reg = <0x170000 0x40000>; - read-only; - }; - - radio@1b0000 { - label = "radio"; - reg = <0x1b0000 0x40000>; - read-only; - }; - - os-image@1f0000 { - label = "os-image"; - reg = <0x1f0000 0x400000>; - }; - - rootfs@5f0000 { - label = "rootfs"; - reg = <0x5f0000 0x1900000>; - }; - - defaultmac: default-mac@1ef0000 { - label = "default-mac"; - reg = <0x1ef0000 0x00200>; - read-only; - }; - - pin@1ef0200 { - label = "pin"; - reg = <0x1ef0200 0x00200>; - read-only; - }; - - product-info@1ef0400 { - label = "product-info"; - reg = <0x1ef0400 0x0fc00>; - read-only; - }; - - partition-table@1f00000 { - label = "partition-table"; - reg = <0x1f00000 0x10000>; - read-only; - }; - - soft-version@1f10000 { - label = "soft-version"; - reg = <0x1f10000 0x10000>; - read-only; - }; - - support-list@1f20000 { - label = "support-list"; - reg = <0x1f20000 0x10000>; - read-only; - }; - - profile@1f30000 { - label = "profile"; - reg = <0x1f30000 0x10000>; - read-only; - }; - - default-config@1f40000 { - label = "default-config"; - reg = <0x1f40000 0x10000>; - read-only; - }; - - user-config@1f50000 { - label = "user-config"; - reg = <0x1f50000 0x40000>; - read-only; - }; - - qos-db@1f90000 { - label = "qos-db"; - reg = <0x1f90000 0x40000>; - read-only; - }; - - usb-config@1fd0000 { - label = "usb-config"; - reg = <0x1fd0000 0x10000>; - read-only; - }; - - log@1fe0000 { - label = "log"; - reg = <0x1fe0000 0x20000>; - read-only; - }; - }; - }; - }; - - usb3_0: usb3@110f8800 { - status = "okay"; - - pinctrl-0 = <&usb0_pwr_en_pin>; - pinctrl-names = "default"; - }; - - usb3_1: usb3@100f8800 { - status = "okay"; - - pinctrl-0 = <&usb1_pwr_en_pin>; - pinctrl-names = "default"; - }; - - pcie0: pci@1b500000 { - status = "okay"; - }; - - pcie1: pci@1b700000 { - status = "okay"; - force_gen1 = <1>; - }; - - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, - <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - }; - }; - - gmac1: ethernet@37200000 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&defaultmac 0x8>; - mtd-mac-address-increment = <1>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - gmac2: ethernet@37400000 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - - mtd-mac-address = <&defaultmac 0x8>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 49 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - ledswitch { - label = "ledswitch"; - gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - lan { - label = "white:lan"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_HIGH>; - }; - - usb4 { - label = "white:usb_4"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - usb2 { - label = "white:usb_2"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - wps { - label = "white:wps"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - wan_amber { - label = "amber:wan"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>; - }; - - wan_white { - label = "white:wan"; - gpios = <&qcom_pinmux 33 GPIO_ACTIVE_LOW>; - }; - - power: power { - label = "white:power"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - general: general { - label = "white:general"; - gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&adm_dma { - status = "okay"; -}; diff --git a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-d7800.dts b/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-d7800.dts deleted file mode 100644 index ba4bb9022d..0000000000 --- a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-d7800.dts +++ /dev/null @@ -1,396 +0,0 @@ -#include "qcom-ipq8064-v2.0.dtsi" - -#include - -/ { - model = "Netgear Nighthawk X4 D7800"; - compatible = "netgear,d7800", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0xe000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - mdio-gpio0 = &mdio0; - - led-boot = &power_white; - led-failsafe = &power_amber; - led-running = &power_white; - led-upgrade = &power_amber; - }; - - chosen { - bootargs = "rootfstype=squashfs noinitrd"; - stdout-path = "serial0:115200n8"; - }; - - soc { - pinmux@800000 { - button_pins: button_pins { - mux { - pins = "gpio6", "gpio54", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - i2c4_pins: i2c4_pinmux { - mux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - drive-strength = <12>; - bias-disable; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23", - "gpio24","gpio26", "gpio53", "gpio64"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - nand_pins: nand_pins { - disable { - pins = "gpio34", "gpio35", "gpio36", - "gpio37", "gpio38"; - function = "nand"; - drive-strength = <10>; - bias-disable; - }; - - pullups { - pins = "gpio39"; - function = "nand"; - drive-strength = <10>; - bias-pull-up; - }; - - hold { - pins = "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - function = "nand"; - drive-strength = <10>; - bias-bus-hold; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - }; - - usb0_pwr_en_pins: usb0_pwr_en_pins { - mux { - pins = "gpio15"; - function = "gpio"; - drive-strength = <12>; - bias-pull-down; - output-high; - }; - }; - - usb1_pwr_en_pins: usb1_pwr_en_pins { - mux { - pins = "gpio16", "gpio68"; - function = "gpio"; - drive-strength = <12>; - bias-pull-down; - output-high; - }; - }; - }; - - gsbi@16300000 { - qcom,mode = ; - status = "okay"; - serial@16340000 { - status = "okay"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ - }; - - sata-phy@1b400000 { - status = "okay"; - }; - - sata@29000000 { - ports-implemented = <0x1>; - status = "okay"; - }; - - usb3_0: usb3@110f8800 { - status = "okay"; - - pinctrl-0 = <&usb0_pwr_en_pins>; - pinctrl-names = "default"; - }; - - usb3_1: usb3@100f8800 { - status = "okay"; - - pinctrl-0 = <&usb1_pwr_en_pins>; - pinctrl-names = "default"; - }; - - pcie0: pci@1b500000 { - status = "okay"; - reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&pcie0_pins>; - pinctrl-names = "default"; - }; - - pcie1: pci@1b700000 { - status = "okay"; - reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&pcie1_pins>; - pinctrl-names = "default"; - force_gen1 = <1>; - }; - - nand@1ac00000 { - status = "okay"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - #address-cells = <1>; - #size-cells = <0>; - - cs0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - qcadata@0 { - label = "qcadata"; - reg = <0x0000000 0x0c80000>; - read-only; - }; - - APPSBL@c80000 { - label = "APPSBL"; - reg = <0x0c80000 0x0500000>; - read-only; - }; - - APPSBLENV@1180000 { - label = "APPSBLENV"; - reg = <0x1180000 0x0080000>; - read-only; - }; - - art: art@1200000 { - label = "art"; - reg = <0x1200000 0x0140000>; - read-only; - }; - - artbak: art@1340000 { - label = "artbak"; - reg = <0x1340000 0x0140000>; - read-only; - }; - - kernel@1480000 { - label = "kernel"; - reg = <0x1480000 0x0400000>; - }; - - ubi@1880000 { - label = "ubi"; - reg = <0x1880000 0x1C00000>; - }; - - netgear@3480000 { - label = "netgear"; - reg = <0x3480000 0x4480000>; - read-only; - }; - - reserve@7900000 { - label = "reserve"; - reg = <0x7900000 0x0700000>; - read-only; - }; - }; - }; - }; - - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, - <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - }; - }; - - gmac1: ethernet@37200000 { - status = "okay"; - phy-mode = "rgmii"; - phy-handle = <&phy4>; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&art 6>; - }; - - gmac2: ethernet@37400000 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - - mtd-mac-address = <&art 0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - usb1 { - label = "white:usb1"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - usb2 { - label = "white:usb2"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - power_amber: power_amber { - label = "amber:power"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - wan_white { - label = "white:wan"; - gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; - }; - - wan_amber { - label = "amber:wan"; - gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; - }; - - wps { - label = "white:wps"; - gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; - }; - - esata { - label = "white:esata"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; - }; - - power_white: power_white { - label = "white:power"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - wifi { - label = "white:wifi"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&adm_dma { - status = "okay"; -}; diff --git a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-db149.dts b/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-db149.dts deleted file mode 100644 index 35b7e0ea37..0000000000 --- a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-db149.dts +++ /dev/null @@ -1,216 +0,0 @@ -#include "qcom-ipq8064-v1.0.dtsi" - -/ { - model = "Qualcomm IPQ8064/DB149"; - compatible = "qcom,ipq8064-db149", "qcom,ipq8064"; - - aliases { - serial0 = &gsbi2_serial; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - soc { - pinmux@800000 { - i2c4_pins: i2c4_pinmux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - bias-disable; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - drive-strength = <10>; - bias-none; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - rgmii0_pins: rgmii0_pins { - mux { - pins = "gpio2", "gpio66"; - drive-strength = <8>; - bias-disable; - }; - }; - }; - - gsbi2: gsbi@12480000 { - qcom,mode = ; - status = "okay"; - - gsbi2_serial: serial@12490000 { - status = "okay"; - }; - }; - - gsbi5: gsbi@1a200000 { - qcom,mode = ; - status = "okay"; - - spi4: spi@1a280000 { - status = "okay"; - spi-max-frequency = <50000000>; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 0>; - - flash: m25p80@0 { - compatible = "s25fl256s1"; - #address-cells = <1>; - #size-cells = <1>; - spi-max-frequency = <50000000>; - reg = <0>; - m25p,fast-read; - - partition@0 { - label = "lowlevel_init"; - reg = <0x0 0x1b0000>; - }; - - partition@1 { - label = "u-boot"; - reg = <0x1b0000 0x80000>; - }; - - partition@2 { - label = "u-boot-env"; - reg = <0x230000 0x40000>; - }; - - partition@3 { - label = "caldata"; - reg = <0x270000 0x40000>; - }; - - partition@4 { - label = "firmware"; - reg = <0x2b0000 0x1d50000>; - }; - }; - }; - }; - - sata-phy@1b400000 { - status = "okay"; - }; - - sata@29000000 { - status = "okay"; - }; - - usb3_0: usb3@110f8800 { - status = "okay"; - }; - - usb3_1: usb3@100f8800 { - status = "okay"; - }; - - pcie0: pci@1b500000 { - status = "okay"; - }; - - pcie1: pci@1b700000 { - status = "okay"; - }; - - pcie2: pci@1b900000 { - status = "okay"; - }; - - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>; - - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - }; - - phy6: ethernet-phy@6 { - reg = <6>; - }; - - phy7: ethernet-phy@7 { - reg = <7>; - }; - }; - - gmac0: ethernet@37000000 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <0>; - phy-handle = <&phy4>; - - pinctrl-0 = <&rgmii0_pins>; - pinctrl-names = "default"; - }; - - gmac1: ethernet@37200000 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <1>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - gmac2: ethernet@37400000 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - phy-handle = <&phy6>; - }; - - gmac3: ethernet@37600000 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <3>; - phy-handle = <&phy7>; - }; - }; -}; diff --git a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts b/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts deleted file mode 100644 index 1b8ab36c4f..0000000000 --- a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts +++ /dev/null @@ -1,389 +0,0 @@ -#include "qcom-ipq8064-v2.0.dtsi" - -#include - -/ { - model = "Linksys EA8500 WiFi Router"; - compatible = "linksys,ea8500", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - mdio-gpio0 = &mdio0; - - led-boot = &power; - led-failsafe = &power; - led-running = &power; - led-upgrade = &power; - }; - - chosen { - bootargs = "console=ttyMSM0,115200n8"; - stdout-path = "serial0:115200n8"; - append-rootblock = "ubi.mtd="; /* append to bootargs adding the root deviceblock nbr from bootloader */ - }; - - soc { - pinmux@800000 { - button_pins: button_pins { - mux { - pins = "gpio65", "gpio67", "gpio68"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - i2c4_pins: i2c4_pinmux { - mux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - drive-strength = <12>; - bias-disable; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio6", "gpio53", "gpio54"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - nand_pins: nand_pins { - disable { - pins = "gpio34", "gpio35", "gpio36", - "gpio37", "gpio38"; - function = "nand"; - drive-strength = <10>; - bias-disable; - }; - - pullups { - pins = "gpio39"; - function = "nand"; - drive-strength = <10>; - bias-pull-up; - }; - - hold { - pins = "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - function = "nand"; - drive-strength = <10>; - bias-bus-hold; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - }; - }; - - gsbi@16300000 { - qcom,mode = ; - status = "okay"; - serial@16340000 { - status = "okay"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ - }; - - sata-phy@1b400000 { - status = "okay"; - }; - - sata@29000000 { - status = "okay"; - }; - - usb3_0: usb3@110f8800 { - status = "okay"; - }; - - usb3_1: usb3@100f8800 { - status = "okay"; - }; - - pcie0: pci@1b500000 { - status = "okay"; - force_gen1 = <1>; - }; - - pcie1: pci@1b700000 { - status = "okay"; - }; - - pcie2: pci@1b900000 { - status = "okay"; - }; - - nand@1ac00000 { - status = "okay"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - cs0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - SBL1@0 { - label = "SBL1"; - reg = <0x0000000 0x0040000>; - read-only; - }; - - MIBIB@40000 { - label = "MIBIB"; - reg = <0x0040000 0x0140000>; - read-only; - }; - - SBL2@180000 { - label = "SBL2"; - reg = <0x0180000 0x0140000>; - read-only; - }; - - SBL3@2c0000 { - label = "SBL3"; - reg = <0x02c0000 0x0280000>; - read-only; - }; - - DDRCONFIG@540000 { - label = "DDRCONFIG"; - reg = <0x0540000 0x0120000>; - read-only; - }; - - SSD@660000 { - label = "SSD"; - reg = <0x0660000 0x0120000>; - read-only; - }; - - TZ@780000 { - label = "TZ"; - reg = <0x0780000 0x0280000>; - read-only; - }; - - RPM@a00000 { - label = "RPM"; - reg = <0x0a00000 0x0280000>; - read-only; - }; - - art: art@c80000 { - label = "art"; - reg = <0x0c80000 0x0140000>; - read-only; - }; - - APPSBL@dc0000 { - label = "APPSBL"; - reg = <0x0dc0000 0x0100000>; - read-only; - }; - - u_env@ec0000 { - label = "u_env"; - reg = <0x0ec0000 0x0040000>; - }; - - s_env@f00000 { - label = "s_env"; - reg = <0x0f00000 0x0040000>; - }; - - devinfo@f40000 { - label = "devinfo"; - reg = <0x0f40000 0x0040000>; - }; - - linux@f80000 { - label = "kernel1"; - reg = <0x0f80000 0x2800000>; /* 3 MB spill to rootfs*/ - }; - - rootfs@1280000 { - label = "rootfs1"; - reg = <0x1280000 0x2500000>; - }; - - linux2@3780000 { - label = "kernel2"; - reg = <0x3780000 0x2800000>; - }; - - rootfs2@3a80000 { - label = "rootfs2"; - reg = <0x3a80000 0x2500000>; - }; - - syscfg@5f80000 { - label = "syscfg"; - reg = <0x5f80000 0x2080000>; - }; - }; - }; - }; - - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, - <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x00010 0x2613a0 /* PWS_REG */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - }; - }; - - gmac1: ethernet@37200000 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <1>; - qcom,phy_mdio_addr = <4>; - qcom,poll_required = <1>; - qcom,rgmii_delay = <0>; - qcom,emulation = <0>; - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - //lan - gmac2: ethernet@37400000 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - qcom,phy_mdio_addr = <0>; /* none */ - qcom,poll_required = <0>; /* no polling */ - qcom,rgmii_delay = <0>; - qcom,emulation = <0>; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - adm_dma: dma@18300000 { - status = "okay"; - }; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - wps { - label = "green:wps"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - }; - - power: power { - label = "white:power"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - - wifi { - label = "green:wifi"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_HIGH>; - }; - }; -}; - diff --git a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-r7500.dts b/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-r7500.dts deleted file mode 100644 index 1d6be1288a..0000000000 --- a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-r7500.dts +++ /dev/null @@ -1,366 +0,0 @@ -#include "qcom-ipq8064-v1.0.dtsi" - -#include -#include - -/ { - model = "Netgear Nighthawk X4 R7500"; - compatible = "netgear,r7500", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0xe000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - mdio-gpio0 = &mdio0; - - led-boot = &power_white; - led-failsafe = &power_amber; - led-running = &power_white; - led-upgrade = &power_amber; - }; - - chosen { - bootargs = "rootfstype=squashfs noinitrd"; - stdout-path = "serial0:115200n8"; - }; - - soc { - pinmux@800000 { - button_pins: button_pins { - mux { - pins = "gpio6", "gpio54", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - i2c4_pins: i2c4_pinmux { - mux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - drive-strength = <12>; - bias-disable; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23", - "gpio24","gpio26", "gpio53", "gpio64"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - nand_pins: nand_pins { - disable { - pins = "gpio34", "gpio35", "gpio36", - "gpio37", "gpio38"; - function = "nand"; - drive-strength = <10>; - bias-disable; - }; - - pullups { - pins = "gpio39"; - function = "nand"; - drive-strength = <10>; - bias-pull-up; - }; - - hold { - pins = "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - function = "nand"; - drive-strength = <10>; - bias-bus-hold; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - }; - }; - - gsbi@16300000 { - qcom,mode = ; - status = "okay"; - serial@16340000 { - status = "okay"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ - }; - - sata-phy@1b400000 { - status = "okay"; - }; - - sata@29000000 { - status = "okay"; - }; - - usb3_0: usb3@110f8800 { - clocks = <&gcc USB30_1_MASTER_CLK>; - status = "okay"; - }; - - usb3_1: usb3@100f8800 { - clocks = <&gcc USB30_0_MASTER_CLK>; - status = "okay"; - }; - - pcie0: pci@1b500000 { - status = "okay"; - }; - - pcie1: pci@1b700000 { - status = "okay"; - force_gen1 = <1>; - }; - - nand@1ac00000 { - status = "okay"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - cs0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - qcadata@0 { - label = "qcadata"; - reg = <0x0000000 0x0c80000>; - read-only; - }; - - APPSBL@c80000 { - label = "APPSBL"; - reg = <0x0c80000 0x0500000>; - read-only; - }; - - APPSBLENV@1180000 { - label = "APPSBLENV"; - reg = <0x1180000 0x0080000>; - read-only; - }; - - art: art@1200000 { - label = "art"; - reg = <0x1200000 0x0140000>; - read-only; - }; - - kernel@1340000 { - label = "kernel"; - reg = <0x1340000 0x0400000>; - }; - - ubi@1740000 { - label = "ubi"; - reg = <0x1740000 0x1600000>; - }; - - netgear@2d40000 { - label = "netgear"; - reg = <0x2d40000 0x0c00000>; - read-only; - }; - - reserve@3940000 { - label = "reserve"; - reg = <0x3940000 0x46c0000>; - read-only; - }; - }; - }; - }; - - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, - <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - }; - }; - - gmac1: ethernet@37200000 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&art 6>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - gmac2: ethernet@37400000 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - - mtd-mac-address = <&art 0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - usb1 { - label = "white:usb1"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - usb2 { - label = "white:usb2"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - power_amber: power_amber { - label = "amber:power"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - wan_white { - label = "white:wan"; - gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; - }; - - wan_amber { - label = "amber:wan"; - gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; - }; - - wps { - label = "white:wps"; - gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; - }; - - esata { - label = "white:esata"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; - }; - - power_white: power_white { - label = "white:power"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - wifi { - label = "white:wifi"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&tcsr { - qcom,usb-ctrl-select = ; - compatible = "qcom,tcsr"; -}; - -&adm_dma { - status = "okay"; -}; diff --git a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts b/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts deleted file mode 100644 index e9d183a8eb..0000000000 --- a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts +++ /dev/null @@ -1,395 +0,0 @@ -#include "qcom-ipq8064-v2.0.dtsi" - -#include - -/ { - model = "Netgear Nighthawk X4 R7500v2"; - compatible = "netgear,r7500v2", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - - rsvd@5fe00000 { - reg = <0x5fe00000 0x200000>; - reusable; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - mdio-gpio0 = &mdio0; - - led-boot = &power; - led-failsafe = &power; - led-running = &power; - led-upgrade = &power; - }; - - chosen { - bootargs = "rootfstype=squashfs noinitrd"; - stdout-path = "serial0:115200n8"; - }; - - soc { - pinmux@800000 { - button_pins: button_pins { - mux { - pins = "gpio6", "gpio54", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - i2c4_pins: i2c4_pinmux { - mux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - drive-strength = <12>; - bias-disable; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23", - "gpio24","gpio26", "gpio53", "gpio64"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - nand_pins: nand_pins { - disable { - pins = "gpio34", "gpio35", "gpio36", - "gpio37", "gpio38"; - function = "nand"; - drive-strength = <10>; - bias-disable; - }; - - pullups { - pins = "gpio39"; - function = "nand"; - drive-strength = <10>; - bias-pull-up; - }; - - hold { - pins = "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - function = "nand"; - drive-strength = <10>; - bias-bus-hold; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - }; - - usb0_pwr_en_pins: usb0_pwr_en_pins { - mux { - pins = "gpio15"; - function = "gpio"; - drive-strength = <12>; - bias-pull-down; - output-high; - }; - }; - - usb1_pwr_en_pins: usb1_pwr_en_pins { - mux { - pins = "gpio16", "gpio68"; - function = "gpio"; - drive-strength = <12>; - bias-pull-down; - output-high; - }; - }; - }; - - gsbi@16300000 { - qcom,mode = ; - status = "okay"; - serial@16340000 { - status = "okay"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ - }; - - sata-phy@1b400000 { - status = "okay"; - }; - - sata@29000000 { - status = "okay"; - }; - - usb3_0: usb3@110f8800 { - status = "okay"; - - pinctrl-0 = <&usb0_pwr_en_pins>; - pinctrl-names = "default"; - }; - - usb3_1: usb3@100f8800 { - status = "okay"; - - pinctrl-0 = <&usb1_pwr_en_pins>; - pinctrl-names = "default"; - }; - - pcie0: pci@1b500000 { - status = "okay"; - reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>; - pinctrl-0 = <&pcie0_pins>; - pinctrl-names = "default"; - }; - - pcie1: pci@1b700000 { - status = "okay"; - reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>; - pinctrl-0 = <&pcie1_pins>; - pinctrl-names = "default"; - force_gen1 = <1>; - }; - - nand@1ac00000 { - status = "okay"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - cs0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - qcadata@0 { - label = "qcadata"; - reg = <0x0000000 0x0c80000>; - read-only; - }; - - APPSBL@c80000 { - label = "APPSBL"; - reg = <0x0c80000 0x0500000>; - read-only; - }; - - APPSBLENV@1180000 { - label = "APPSBLENV"; - reg = <0x1180000 0x0080000>; - read-only; - }; - - art: art@1200000 { - label = "art"; - reg = <0x1200000 0x0140000>; - read-only; - }; - - artbak: art@1340000 { - label = "artbak"; - reg = <0x1340000 0x0140000>; - read-only; - }; - - kernel@1480000 { - label = "kernel"; - reg = <0x1480000 0x0400000>; - }; - - ubi@1880000 { - label = "ubi"; - reg = <0x1880000 0x6080000>; - }; - - reserve@7900000 { - label = "reserve"; - reg = <0x7900000 0x0700000>; - read-only; - }; - }; - }; - }; - - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, - <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0xaa545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - }; - }; - - gmac1: ethernet@37200000 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&art 6>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - gmac2: ethernet@37400000 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - - mtd-mac-address = <&art 0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - usb1 { - label = "amber:usb1"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - usb3 { - label = "amber:usb3"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - status { - label = "amber:status"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - internet { - label = "white:internet"; - gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; - }; - - wan { - label = "white:wan"; - gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; - }; - - wps { - label = "white:wps"; - gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; - }; - - esata { - label = "white:esata"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; - }; - - power: power { - label = "white:power"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - wifi { - label = "white:wifi"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&adm_dma { - status = "okay"; -}; diff --git a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi b/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi deleted file mode 100644 index dd272c7fc7..0000000000 --- a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi +++ /dev/null @@ -1,30 +0,0 @@ -#include "qcom-ipq8064-v1.0.dtsi" - -/ { - soc: soc { - - pcie0: pci@1b500000 { - phy-tx0-term-offset = <0>; - }; - - pcie1: pci@1b700000 { - phy-tx0-term-offset = <0>; - }; - - pcie2: pci@1b900000 { - phy-tx0-term-offset = <0>; - }; - }; -}; - -&ss_phy_0 { - rx_eq = <2>; - tx_deamp_3_5db = <32>; - mpll = <0xa0>; -}; - -&ss_phy_1 { - rx_eq = <2>; - tx_deamp_3_5db = <32>; - mpll = <0xa0>; -}; diff --git a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts b/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts deleted file mode 100644 index 8c171bc2e3..0000000000 --- a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts +++ /dev/null @@ -1,402 +0,0 @@ -#include "qcom-ipq8064-v2.0.dtsi" - -#include - -/ { - model = "TP-Link Archer VR2600v"; - compatible = "tplink,vr2600v", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - mdio-gpio0 = &mdio0; - - led-boot = &power; - led-failsafe = &general; - led-running = &power; - led-upgrade = &general; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - soc { - pinmux@800000 { - led_pins: led_pins { - mux { - pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio17", - "gpio26", "gpio53", "gpio56", "gpio66"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - i2c4_pins: i2c4_pinmux { - mux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - drive-strength = <12>; - bias-disable; - }; - }; - - button_pins: button_pins { - mux { - pins = "gpio54", "gpio64", "gpio65", "gpio67", "gpio68"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - bias-pull-down; - }; - - data { - pins = "gpio18", "gpio19"; - drive-strength = <10>; - }; - - cs { - pins = "gpio20"; - drive-strength = <10>; - bias-pull-up; - }; - - clk { - pins = "gpio21"; - drive-strength = <12>; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - }; - }; - - gsbi@16300000 { - qcom,mode = ; - status = "okay"; - serial@16340000 { - status = "okay"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ - }; - - gsbi5: gsbi@1a200000 { - qcom,mode = ; - status = "okay"; - - spi4: spi@1a280000 { - status = "okay"; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; - - flash: W25Q128@0 { - compatible = "jedec,spi-nor"; - #address-cells = <1>; - #size-cells = <1>; - spi-max-frequency = <50000000>; - reg = <0>; - - SBL1@0 { - label = "SBL1"; - reg = <0x0 0x20000>; - read-only; - }; - - MIBIB@20000 { - label = "MIBIB"; - reg = <0x20000 0x20000>; - read-only; - }; - - SBL2@40000 { - label = "SBL2"; - reg = <0x40000 0x40000>; - read-only; - }; - - SBL3@80000 { - label = "SBL3"; - reg = <0x80000 0x80000>; - read-only; - }; - - DDRCONFIG@100000 { - label = "DDRCONFIG"; - reg = <0x100000 0x10000>; - read-only; - }; - - SSD@110000 { - label = "SSD"; - reg = <0x110000 0x10000>; - read-only; - }; - - TZ@120000 { - label = "TZ"; - reg = <0x120000 0x80000>; - read-only; - }; - - RPM@1a0000 { - label = "RPM"; - reg = <0x1a0000 0x80000>; - read-only; - }; - - APPSBL@220000 { - label = "APPSBL"; - reg = <0x220000 0x80000>; - read-only; - }; - - APPSBLENV@2a0000 { - label = "APPSBLENV"; - reg = <0x2a0000 0x40000>; - read-only; - }; - - OLDART@2e0000 { - label = "OLDART"; - reg = <0x2e0000 0x40000>; - read-only; - }; - - kernel@320000 { - label = "kernel"; - reg = <0x320000 0x300000>; - }; - - rootfs@620000 { - label = "rootfs"; - reg = <0x620000 0x960000>; - }; - - defaultmac: default-mac@0xfaf100 { - label = "default-mac"; - reg = <0xfaf100 0x00200>; - read-only; - }; - - ART@fc0000 { - label = "ART"; - reg = <0xfc0000 0x40000>; - read-only; - }; - }; - }; - }; - - usb3_0: usb3@110f8800 { - status = "okay"; - }; - - usb3_1: usb3@100f8800 { - status = "okay"; - }; - - pcie0: pci@1b500000 { - status = "okay"; - }; - - pcie1: pci@1b700000 { - status = "okay"; - force_gen1 = <1>; - }; - - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, - <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - }; - }; - - gmac1: ethernet@37200000 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&defaultmac 0>; - mtd-mac-address-increment = <1>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - gmac2: ethernet@37400000 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - - mtd-mac-address = <&defaultmac 0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - dect { - label = "dect"; - gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - ledswitch { - label = "ledswitch"; - gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - dsl { - label = "white:dsl"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - usb { - label = "white:usb"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - lan { - label = "white:lan"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - wlan2g { - label = "white:wlan2g"; - gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>; - }; - - wlan5g { - label = "white:wlan5g"; - gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>; - }; - - power: power { - label = "white:power"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - phone { - label = "white:phone"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - }; - - wan { - label = "white:wan"; - gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>; - }; - - general: general { - label = "white:general"; - gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&adm_dma { - status = "okay"; -}; diff --git a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts b/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts deleted file mode 100644 index 58b5296878..0000000000 --- a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts +++ /dev/null @@ -1,427 +0,0 @@ -#include "qcom-ipq8064-v2.0.dtsi" - -#include - -/ { - model = "NEC Aterm WG2600HP"; - compatible = "nec,wg2600hp", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - mdio-gpio0 = &mdio0; - - led-boot = &power_green; - led-failsafe = &power_red; - led-running = &power_green; - led-upgrade = &power_green; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - soc { - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, - <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x06000000 /* PAD0_MODE */ - 0x0000c 0x00080080 /* PAD6_MODE */ - 0x000e4 0x0006a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x0000004e /* PORT0_STATUS */ - 0x00094 0x0000004e /* PORT6_STATUS */ - >; - }; - - ethernet-phy@4 { - reg = <4>; - }; - }; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - bridge { - label = "bridge"; - gpios = <&qcom_pinmux 24 GPIO_ACTIVE_LOW>; - linux,code = ; - linux,input-type = ; - }; - - converter { - label = "converter"; - gpios = <&qcom_pinmux 25 GPIO_ACTIVE_LOW>; - linux,code = ; - linux,input-type = ; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - converter_green { - label = "green:converter"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_HIGH>; - }; - - power_red: power_red { - label = "red:power"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - active_green { - label = "green:active"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - active_red { - label = "red:active"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - power_green: power_green { - label = "green:power"; - gpios = <&qcom_pinmux 14 GPIO_ACTIVE_HIGH>; - }; - - converter_red { - label = "red:converter"; - gpios = <&qcom_pinmux 15 GPIO_ACTIVE_HIGH>; - }; - - wlan2g_green { - label = "green:wlan2g"; - gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>; - }; - - wlan2g_red { - label = "red:wlan2g"; - gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>; - }; - - wlan5g_green { - label = "green:wlan5g"; - gpios = <&qcom_pinmux 57 GPIO_ACTIVE_HIGH>; - }; - - wlan5g_red { - label = "red:wlan5g"; - gpios = <&qcom_pinmux 58 GPIO_ACTIVE_HIGH>; - }; - - tv_green { - label = "green:tv"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; - }; - - tv_red { - label = "red:tv"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&adm_dma { - status = "okay"; -}; - -&gmac1 { - status = "okay"; - - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&PRODUCTDATA 6>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gmac2 { - status = "okay"; - - phy-mode = "sgmii"; - qcom,id = <2>; - - mtd-mac-address = <&PRODUCTDATA 0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gsbi4 { - status = "okay"; - qcom,mode = ; -}; - -&gsbi4_serial { - status = "okay"; -}; - -&gsbi5 { - status = "okay"; - - qcom,mode = ; - - spi@1a280000 { - status = "okay"; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; - - flash@0 { - compatible = "jedec,spi-nor"; - spi-max-frequency = <50000000>; - reg = <0>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - SBL1@0 { - label = "SBL1"; - reg = <0x0 0x20000>; - read-only; - }; - - MIBIB@20000 { - label = "MIBIB"; - reg = <0x20000 0x20000>; - read-only; - }; - - SBL2@40000 { - label = "SBL2"; - reg = <0x40000 0x40000>; - read-only; - }; - - SBL3@80000 { - label = "SBL3"; - reg = <0x80000 0x80000>; - read-only; - }; - - DDRCONFIG@100000 { - label = "DDRCONFIG"; - reg = <0x100000 0x10000>; - read-only; - }; - - SSD@110000 { - label = "SSD"; - reg = <0x110000 0x10000>; - read-only; - }; - - TZ@120000 { - label = "TZ"; - reg = <0x120000 0x80000>; - read-only; - }; - - RPM@1a0000 { - label = "RPM"; - reg = <0x1a0000 0x80000>; - read-only; - }; - - APPSBL@220000 { - label = "APPSBL"; - reg = <0x220000 0x80000>; - read-only; - }; - - APPSBLENV@2a0000 { - label = "APPSBLENV"; - reg = <0x2a0000 0x10000>; - }; - - PRODUCTDATA: PRODUCTDATA@2b0000 { - label = "PRODUCTDATA"; - reg = <0x2b0000 0x30000>; - read-only; - }; - - ART@2e0000 { - label = "ART"; - reg = <0x2e0000 0x40000>; - read-only; - }; - - TP@320000 { - label = "TP"; - reg = <0x320000 0x40000>; - read-only; - }; - - TINY@360000 { - label = "TINY"; - reg = <0x360000 0x500000>; - read-only; - }; - - firmware@860000 { - compatible = "denx,uimage"; - label = "firmware"; - reg = <0x860000 0x17a0000>; - }; - }; - }; - }; -}; - -&usb3_0 { - status = "okay"; - - pinctrl-0 = <&usb_pwr_en_pins>; - pinctrl-names = "default"; -}; - -&usb3_1 { - status = "okay"; -}; - -&pcie0 { - status = "okay"; -}; - -&pcie1 { - status = "okay"; - force_gen1 = <1>; -}; - -&qcom_pinmux { - button_pins: button_pins { - mux { - pins = "gpio16", "gpio54", "gpio24", "gpio25"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - i2c4_pins: i2c4_pinmux { - mux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - drive-strength = <12>; - bias-disable; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio14", - "gpio15", "gpio55", "gpio56", "gpio57", "gpio58", - "gpio64", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-down; - }; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - bias-pull-down; - }; - - data { - pins = "gpio18", "gpio19"; - drive-strength = <10>; - }; - - cs { - pins = "gpio20"; - drive-strength = <10>; - bias-pull-up; - }; - - clk { - pins = "gpio21"; - drive-strength = <12>; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - }; - - usb_pwr_en_pins: usb_pwr_en_pins { - mux { - pins = "gpio22"; - function = "gpio"; - drive-strength = <2>; - bias-pull-down; - output-high; - }; - }; -}; diff --git a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-wpq864.dts b/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-wpq864.dts deleted file mode 100644 index 0347cac430..0000000000 --- a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-wpq864.dts +++ /dev/null @@ -1,563 +0,0 @@ -/* - * BSD LICENSE - * - * Copyright (C) 2017 Christian Mehlis - * Copyright (C) 2018 Mathias Kresin - * All rights reserved. - * - * Redistribution and use in source and binary forms, with or without - * modification, are permitted provided that the following conditions - * are met: - * - * 1. Redistributions of source code must retain the above copyright - * notice, this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright - * notice, this list of conditions and the following disclaimer in the - * documentation and/or other materials provided with the distribution. - * 3. Neither the names of the copyright holders nor the names of any - * contributors may be used to endorse or promote products derived - * from this software without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS - * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT - * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR - * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT - * HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, - * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT - * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, - * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY - * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - */ - -#include "qcom-ipq8064-v1.0.dtsi" - -#include -#include - -/ { - compatible = "compex,wpq864", "qcom,ipq8064"; - model = "Compex WPQ864"; - - aliases { - mdio-gpio0 = &mdio0; - serial0 = &gsbi4_serial; - ethernet0 = &gmac1; - ethernet1 = &gmac0; - - led-boot = &led_pass; - led-failsafe = &led_fail; - led-running = &led_pass; - led-upgrade = &led_pass; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - soc { - rpm@108000 { - pinctrl-0 = <&rpm_pins>; - pinctrl-names = "default"; - }; - - nand@1ac00000 { - status = "okay"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - mt29f2g08abbeah4@0 { - compatible = "qcom,nandcs"; - - reg = <0>; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - SBL1@0 { - label = "SBL1"; - reg = <0x0000000 0x0040000>; - read-only; - }; - - MIBIB@40000 { - label = "MIBIB"; - reg = <0x0040000 0x0140000>; - read-only; - }; - - SBL2@180000 { - label = "SBL2"; - reg = <0x0180000 0x0140000>; - read-only; - }; - - SBL3@2c0000 { - label = "SBL3"; - reg = <0x02c0000 0x0280000>; - read-only; - }; - - DDRCONFIG@540000 { - label = "DDRCONFIG"; - reg = <0x0540000 0x0120000>; - read-only; - }; - - SSD@660000 { - label = "SSD"; - reg = <0x0660000 0x0120000>; - read-only; - }; - - TZ@780000 { - label = "TZ"; - reg = <0x0780000 0x0280000>; - read-only; - }; - - RPM@a00000 { - label = "RPM"; - reg = <0x0a00000 0x0280000>; - read-only; - }; - - APPSBL@c80000 { - label = "APPSBL"; - reg = <0x0c80000 0x0500000>; - read-only; - }; - - APPSBLENV@1180000 { - label = "APPSBLENV"; - reg = <0x1180000 0x0080000>; - }; - - ART@1200000 { - label = "ART"; - reg = <0x1200000 0x0140000>; - }; - - ubi@1340000 { - label = "ubi"; - reg = <0x1340000 0x4000000>; - }; - - BOOTCONFIG@5340000 { - label = "BOOTCONFIG"; - reg = <0x5340000 0x0060000>; - }; - - SBL2-1@53a0000- { - label = "SBL2_1"; - reg = <0x53a0000 0x0140000>; - read-only; - }; - - SBL3-1@54e0000 { - label = "SBL3_1"; - reg = <0x54e0000 0x0280000>; - read-only; - }; - - DDRCONFIG-1@5760000 { - label = "DDRCONFIG_1"; - reg = <0x5760000 0x0120000>; - read-only; - }; - - SSD-1@5880000 { - label = "SSD_1"; - reg = <0x5880000 0x0120000>; - read-only; - }; - - TZ-1@59a0000 { - label = "TZ_1"; - reg = <0x59a0000 0x0280000>; - read-only; - }; - - RPM-1@5c20000 { - label = "RPM_1"; - reg = <0x5c20000 0x0280000>; - read-only; - }; - - BOOTCONFIG1@5ea0000 { - label = "BOOTCONFIG1"; - reg = <0x5ea0000 0x0060000>; - }; - - APPSBL-1@5f00000 { - label = "APPSBL_1"; - reg = <0x5f00000 0x0500000>; - read-only; - }; - - ubi-1@6400000 { - label = "ubi_1"; - reg = <0x6400000 0x4000000>; - }; - - unused@a400000 { - label = "unused"; - reg = <0xa400000 0x5c00000>; - }; - }; - }; - }; - }; - - mdio0: mdio { - #address-cells = <1>; - #size-cells = <0>; - - compatible = "virtual,mdio-gpio"; - - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, - <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - - ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - ethernet-phy@4 { - reg = <4>; - }; - }; - - leds { - compatible = "gpio-leds"; - - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - rss4 { - label = "green:rss4"; - gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; - }; - - rss3 { - label = "green:rss3"; - gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - rss2 { - label = "orange:rss2"; - gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>; - }; - - rss1 { - label = "red:rss1"; - gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; - }; - - led_pass: pass { - label = "green:pass"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - }; - - led_fail: fail { - label = "green:fail"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - usb { - label = "green:usb"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - usb-pcie { - label = "green:usb-pcie"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - }; - - keys { - compatible = "gpio-keys"; - - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - beeper { - compatible = "gpio-beeper"; - - pinctrl-0 = <&beeper_pins>; - pinctrl-names = "default"; - - gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>; - }; -}; - -&adm_dma { - status = "okay"; -}; - -&gmac1 { - status = "okay"; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - phy-mode = "rgmii"; - qcom,id = <1>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gmac2 { - status = "okay"; - - phy-mode = "sgmii"; - qcom,id = <2>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gsbi4 { - status = "okay"; - qcom,mode = ; -}; - -&gsbi4_serial { - status = "okay"; - - pinctrl-0 = <&uart0_pins>; - pinctrl-names = "default"; -}; - -&gsbi5 { - status = "okay"; - - qcom,mode = ; - - spi@1a280000 { - status = "okay"; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; - - s25fl256s1@0 { - compatible = "jedec,spi-nor"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0>; - spi-max-frequency = <50000000>; - }; - }; -}; - -&ss_phy_0 { /* USB3 port 0 SS phy */ - status = "okay"; - - rx_eq = <2>; - tx_deamp_3_5db = <32>; - mpll = <160>; -}; - -&ss_phy_1 { /* USB3 port 1 SS phy */ - status = "okay"; - - rx_eq = <2>; - tx_deamp_3_5db = <32>; - mpll = <160>; -}; - -&pcie0 { - status = "okay"; - - /delete-property/ pinctrl-0; - /delete-property/ pinctrl-names; - /delete-property/ perst-gpios; -}; - -&pcie1 { - status = "okay"; -}; - -&pcie2 { - status = "okay"; - - /delete-property/ pinctrl-0; - /delete-property/ pinctrl-names; - /delete-property/ perst-gpios; -}; - -&qcom_pinmux { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinctrl0 { - pcie0_pcie2_perst { - pins = "gpio3"; - function = "gpio"; - drive-strength = <2>; - bias-disable; - output-high; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio7", "gpio8", "gpio9", "gpio22", - "gpio23", "gpio24", "gpio25", "gpio53"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - button_pins: button_pins { - mux { - pins = "gpio54"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - beeper_pins: beeper_pins { - mux { - pins = "gpio55"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - rpm_pins: rpm_pins { - mux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - drive-strength = <10>; - bias-disable; - }; - }; - - uart0_pins: uart0_pins { - mux { - pins = "gpio10", "gpio11"; - function = "gsbi4"; - drive-strength = <10>; - bias-disable; - }; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19"; - function = "gsbi5"; - drive-strength = <10>; - bias-pull-down; - }; - - clk { - pins = "gpio21"; - function = "gsbi5"; - drive-strength = <12>; - bias-pull-down; - }; - - cs { - pins = "gpio20"; - function = "gpio"; - drive-strength = <10>; - bias-pull-up; - }; - }; - - nand_pins: nand_pins { - disable { - pins = "gpio34", "gpio35", "gpio36", "gpio37", - "gpio38"; - function = "nand"; - drive-strength = <10>; - bias-disable; - }; - - pullups { - pins = "gpio39"; - function = "nand"; - drive-strength = <10>; - bias-pull-up; - }; - - hold { - pins = "gpio40", "gpio41", "gpio42", "gpio43", - "gpio44", "gpio45", "gpio46", "gpio47"; - function = "nand"; - drive-strength = <10>; - bias-bus-hold; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", - "gpio31", "gpio32", "gpio51", "gpio52", - "gpio59", "gpio60", "gpio61", "gpio62"; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - }; -}; - -&usb3_0 { - status = "okay"; -}; - - -&usb3_1 { - status = "okay"; -}; - -&tcsr { - qcom,usb-ctrl-select = ; -}; diff --git a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts b/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts deleted file mode 100644 index 874e54b4a1..0000000000 --- a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts +++ /dev/null @@ -1,520 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT -#include "qcom-ipq8064-v2.0.dtsi" - -#include - -/ { - model = "Buffalo WXR-2533DHP"; - compatible = "buffalo,wxr-2533dhp", "qcom,ipq8064"; - - memory@42000000 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - - led-boot = &power; - led-failsafe = &diag; - led-running = &power; - led-upgrade = &power; - }; - - chosen { - /* use "ubi_rootfs" volume in "ubi" partition as rootfs */ - bootargs = "ubi.block=0,1 root=/dev/ubiblock0_1 rootfstype=squashfs"; - stdout-path = "serial0:115200n8"; - }; - - soc { - nand@1ac00000 { - status = "okay"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - cs@0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - ubi@0 { - label = "ubi"; - reg = <0x0000000 0x4000000>; - }; - - rootfs_1@4000000 { - label = "rootfs_1"; - reg = <0x4000000 0x4000000>; - }; - }; - }; - }; - - mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, - <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x07600000 /* PAD0_MODE */ - 0x00008 0x01000000 /* PAD5_MODE */ - 0x0000c 0x00000080 /* PAD6_MODE */ - 0x00050 0xcc35cc35 /* LED_CTRL0 */ - 0x00054 0xca35ca35 /* LED_CTRL1 */ - 0x00058 0xc935c935 /* LED_CTRL2 */ - 0x0005c 0x03ffff00 /* LED_CTRL3 */ - 0x000e4 0x0006a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x0000007e /* PORT0_STATUS */ - 0x00094 0x0000007e /* PORT6_STATUS */ - >; - }; - - ethernet-phy@4 { - reg = <4>; - }; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - usb { - label = "green:usb"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "usbport"; - trigger-sources = <&hub_port0 &hub_port1>; - }; - - guestport { - label = "green:guestport"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - diag: diag { - label = "orange:diag"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - internet_orange { - label = "orange:internet"; - gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>; - }; - - internet_white { - label = "white:internet"; - gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; - }; - - wireless_orange { - label = "orange:wireless"; - gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; - }; - - wireless_white { - label = "white:wireless"; - gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; - }; - - router_orange { - label = "orange:router"; - gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>; - }; - - router_white { - label = "white:router"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>; - }; - - power: power { - label = "white:power"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - }; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - power { - label = "power"; - gpios = <&qcom_pinmux 58 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - eject { - label = "eject"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - guest { - label = "guest"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - ap { - label = "ap"; - gpios = <&qcom_pinmux 55 GPIO_ACTIVE_LOW>; - linux,code = ; - linux,input-type = ; - }; - - router { - label = "router"; - gpios = <&qcom_pinmux 56 GPIO_ACTIVE_LOW>; - linux,code = ; - linux,input-type = ; - }; - - auto { - label = "auto"; - gpios = <&qcom_pinmux 57 GPIO_ACTIVE_LOW>; - linux,code = ; - linux,input-type = ; - }; - }; -}; - -&adm_dma { - status = "okay"; -}; - -&gmac1 { - status = "okay"; - - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&ART 6>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gmac2 { - status = "okay"; - - phy-mode = "sgmii"; - qcom,id = <2>; - - mtd-mac-address = <&ART 0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gsbi4 { - status = "okay"; - qcom,mode = ; -}; - -&gsbi4_serial { - status = "okay"; - - pinctrl-0 = <&uart0_pins>; - pinctrl-names = "default"; -}; - -&gsbi5 { - status = "okay"; - qcom,mode = ; - - spi@1a280000 { - status = "okay"; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; - - flash@0 { - compatible = "jedec,spi-nor"; - spi-max-frequency = <50000000>; - reg = <0>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - SBL1@0 { - label = "SBL1"; - reg = <0x0 0x10000>; - read-only; - }; - - MIBIB@10000 { - label = "MIBIB"; - reg = <0x10000 0x20000>; - read-only; - }; - - SBL2@30000 { - label = "SBL2"; - reg = <0x30000 0x30000>; - read-only; - }; - - SBL3@60000 { - label = "SBL3"; - reg = <0x60000 0x30000>; - read-only; - }; - - DDRCONFIG@90000 { - label = "DDRCONFIG"; - reg = <0x90000 0x10000>; - read-only; - }; - - SSD@a0000 { - label = "SSD"; - reg = <0xa0000 0x10000>; - read-only; - }; - - TZ@b0000 { - label = "TZ"; - reg = <0xb0000 0x30000>; - read-only; - }; - - RPM@e0000 { - label = "RPM"; - reg = <0xe0000 0x20000>; - read-only; - }; - - APPSBL@100000 { - label = "APPSBL"; - reg = <0x100000 0x70000>; - read-only; - }; - - APPSBLENV@170000 { - label = "APPSBLENV"; - reg = <0x170000 0x10000>; - read-only; - }; - - ART: ART@180000 { - label = "ART"; - reg = <0x180000 0x40000>; - read-only; - }; - - BOOTCONFIG@1c0000 { - label = "BOOTCONFIG"; - reg = <0x1c0000 0x10000>; - read-only; - }; - - APPSBL_1@1d0000 { - label = "APPSBL_1"; - reg = <0x1d0000 0x70000>; - read-only; - }; - }; - }; - }; -}; - -&usb3_0 { - status = "okay"; - - pinctrl-0 = <&usb_pwr_en_pins>; - pinctrl-names = "default"; -}; - -&usb3_1 { - status = "okay"; -}; - -&dwc3_0 { - #address-cells = <1>; - #size-cells = <0>; - - hub_port0: port@1 { - reg = <1>; - #trigger-source-cells = <0>; - }; -}; - -&dwc3_1 { - #address-cells = <1>; - #size-cells = <0>; - - hub_port1: port@1 { - reg = <1>; - #trigger-source-cells = <0>; - }; -}; - -&pcie0 { - status = "okay"; -}; - -&pcie1 { - status = "okay"; - force_gen1 = <1>; -}; - -&qcom_pinmux { - button_pins: button_pins { - mux { - pins = "gpio6", "gpio54", "gpio55", "gpio56", "gpio57", - "gpio58", "gpio64", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio22", - "gpio23", "gpio24", "gpio25", "gpio26", "gpio53"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - uart0_pins: uart0_pins { - mux { - pins = "gpio10", "gpio11"; - function = "gsbi4"; - drive-strength = <12>; - bias-disable; - }; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - bias-pull-down; - }; - - data { - pins = "gpio18", "gpio19"; - drive-strength = <10>; - }; - - cs{ - pins = "gpio20"; - drive-strength = <10>; - bias-pull-up; - }; - - clk { - pins = "gpio21"; - drive-strength = <12>; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - - nand_pins: nand_pins { - disable { - pins = "gpio34", "gpio35", "gpio36", - "gpio37", "gpio38"; - function = "nand"; - drive-strength = <10>; - bias-disable; - }; - - pullups { - pins = "gpio39"; - function = "nand"; - drive-strength = <10>; - bias-pull-up; - }; - - hold { - pins = "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - function = "nand"; - drive-strength = <10>; - bias-bus-hold; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - }; - - usb_pwr_en_pins: usb_pwr_en_pins { - mux{ - pins = "gpio68"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - output-high; - }; - }; -}; \ No newline at end of file diff --git a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064.dtsi b/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064.dtsi deleted file mode 100644 index a542af7866..0000000000 --- a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064.dtsi +++ /dev/null @@ -1,1512 +0,0 @@ -/dts-v1/; - -#include "skeleton.dtsi" -#include -#include -#include -#include -#include -#include -#include -#include - -/ { - model = "Qualcomm IPQ8064"; - compatible = "qcom,ipq8064"; - interrupt-parent = <&intc>; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - - cpu0: cpu@0 { - compatible = "qcom,krait"; - enable-method = "qcom,kpss-acc-v1"; - device_type = "cpu"; - reg = <0>; - next-level-cache = <&L2>; - qcom,acc = <&acpu0_aux>; - qcom,saw = <&saw0>; - clocks = <&kraitcc 0>, <&kraitcc 4>; - clock-names = "cpu", "l2"; - clock-latency = <100000>; - cpu-supply = <&smb208_s2a>; - operating-points-v2 = <&opp_table0>; - voltage-tolerance = <5>; - cooling-min-state = <0>; - cooling-max-state = <10>; - #cooling-cells = <2>; - cpu-idle-states = <&CPU_SPC>; - }; - - cpu1: cpu@1 { - compatible = "qcom,krait"; - enable-method = "qcom,kpss-acc-v1"; - device_type = "cpu"; - reg = <1>; - next-level-cache = <&L2>; - qcom,acc = <&acpu1_aux>; - qcom,saw = <&saw1>; - clocks = <&kraitcc 1>, <&kraitcc 4>; - clock-names = "cpu", "l2"; - clock-latency = <100000>; - cpu-supply = <&smb208_s2b>; - operating-points-v2 = <&opp_table0>; - voltage-tolerance = <5>; - cooling-min-state = <0>; - cooling-max-state = <10>; - #cooling-cells = <2>; - cpu-idle-states = <&CPU_SPC>; - }; - - L2: l2-cache { - compatible = "cache"; - cache-level = <2>; - qcom,saw = <&saw_l2>; - }; - - qcom,l2 { - qcom,l2-rates = <384000000 1000000000 1200000000>; - qcom,l2-cpufreq = <384000000 600000000 1200000000>; - qcom,l2-volt = <1100000 1100000 1150000>; - qcom,l2-supply = <&smb208_s1a>; - }; - - idle-states { - CPU_SPC: spc { - compatible = "qcom,idle-state-spc", - "arm,idle-state"; - status = "okay"; - entry-latency-us = <400>; - exit-latency-us = <900>; - min-residency-us = <3000>; - }; - }; - }; - - opp_table0: opp_table0 { - compatible = "operating-points-v2-qcom-cpu"; - nvmem-cells = <&speedbin_efuse>; - - opp-384000000 { - opp-hz = /bits/ 64 <384000000>; - opp-microvolt-speed0-pvs0-v0 = <1000000>; - opp-microvolt-speed0-pvs1-v0 = <925000>; - opp-microvolt-speed0-pvs2-v0 = <875000>; - opp-microvolt-speed0-pvs3-v0 = <800000>; - opp-supported-hw = <0x1>; - clock-latency-ns = <100000>; - }; - - opp-600000000 { - opp-hz = /bits/ 64 <600000000>; - opp-microvolt-speed0-pvs0-v0 = <1050000>; - opp-microvolt-speed0-pvs1-v0 = <975000>; - opp-microvolt-speed0-pvs2-v0 = <925000>; - opp-microvolt-speed0-pvs3-v0 = <850000>; - opp-supported-hw = <0x1>; - clock-latency-ns = <100000>; - }; - - opp-800000000 { - opp-hz = /bits/ 64 <800000000>; - opp-microvolt-speed0-pvs0-v0 = <1100000>; - opp-microvolt-speed0-pvs1-v0 = <1025000>; - opp-microvolt-speed0-pvs2-v0 = <995000>; - opp-microvolt-speed0-pvs3-v0 = <900000>; - opp-supported-hw = <0x1>; - clock-latency-ns = <100000>; - }; - - opp-1000000000 { - opp-hz = /bits/ 64 <1000000000>; - opp-microvolt-speed0-pvs0-v0 = <1150000>; - opp-microvolt-speed0-pvs1-v0 = <1075000>; - opp-microvolt-speed0-pvs2-v0 = <1025000>; - opp-microvolt-speed0-pvs3-v0 = <950000>; - opp-supported-hw = <0x1>; - clock-latency-ns = <100000>; - }; - - opp-1200000000 { - opp-hz = /bits/ 64 <1200000000>; - opp-microvolt-speed0-pvs0-v0 = <1200000>; - opp-microvolt-speed0-pvs1-v0 = <1125000>; - opp-microvolt-speed0-pvs2-v0 = <1075000>; - opp-microvolt-speed0-pvs3-v0 = <1000000>; - opp-supported-hw = <0x1>; - clock-latency-ns = <100000>; - }; - - opp-1400000000 { - opp-hz = /bits/ 64 <1400000000>; - opp-microvolt-speed0-pvs0-v0 = <1250000>; - opp-microvolt-speed0-pvs1-v0 = <1175000>; - opp-microvolt-speed0-pvs2-v0 = <1125000>; - opp-microvolt-speed0-pvs3-v0 = <1050000>; - opp-supported-hw = <0x1>; - clock-latency-ns = <100000>; - }; - - }; - - thermal-zones { - tsens_tz_sensor0 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 0>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - - tsens_tz_sensor1 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 1>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - - tsens_tz_sensor2 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 2>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - - tsens_tz_sensor3 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 3>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - - tsens_tz_sensor4 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 4>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - - tsens_tz_sensor5 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 5>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - - tsens_tz_sensor6 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 6>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - - tsens_tz_sensor7 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 7>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - - tsens_tz_sensor8 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 8>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - - tsens_tz_sensor9 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 9>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - - tsens_tz_sensor10 { - polling-delay-passive = <0>; - polling-delay = <0>; - thermal-sensors = <&tsens 10>; - - trips { - cpu-critical-hi { - temperature = <125000>; - hysteresis = <2000>; - type = "critical_high"; - }; - - cpu-config-hi { - temperature = <105000>; - hysteresis = <2000>; - type = "configurable_hi"; - }; - - cpu-config-lo { - temperature = <95000>; - hysteresis = <2000>; - type = "configurable_lo"; - }; - - cpu-critical-low { - temperature = <0>; - hysteresis = <2000>; - type = "critical_low"; - }; - }; - }; - }; - - cpu-pmu { - compatible = "qcom,krait-pmu"; - interrupts = ; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - - nss@40000000 { - reg = <0x40000000 0x1000000>; - no-map; - }; - - smem: smem@41000000 { - reg = <0x41000000 0x200000>; - no-map; - }; - }; - - clocks { - cxo_board { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <25000000>; - }; - - pxo_board { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <25000000>; - }; - - sleep_clk: sleep_clk { - compatible = "fixed-clock"; - clock-frequency = <32768>; - #clock-cells = <0>; - }; - }; - - fab-scaling { - compatible = "qcom,fab-scaling"; - clocks = <&rpmcc RPM_APPS_FABRIC_A_CLK>, <&rpmcc RPM_EBI1_A_CLK>; - clock-names = "apps-fab-clk", "ddr-fab-clk"; - fab_freq_high = <533000000>; - fab_freq_nominal = <400000000>; - cpu_freq_threshold = <1000000000>; - }; - - firmware { - scm { - compatible = "qcom,scm-ipq806x"; - }; - }; - - soc: soc { - #address-cells = <1>; - #size-cells = <1>; - ranges; - compatible = "simple-bus"; - - lpass@28100000 { - compatible = "qcom,lpass-cpu"; - status = "disabled"; - clocks = <&lcc AHBIX_CLK>, - <&lcc MI2S_OSR_CLK>, - <&lcc MI2S_BIT_CLK>; - clock-names = "ahbix-clk", - "mi2s-osr-clk", - "mi2s-bit-clk"; - interrupts = ; - interrupt-names = "lpass-irq-lpaif"; - reg = <0x28100000 0x10000>; - reg-names = "lpass-lpaif"; - }; - - qfprom: qfprom@700000 { - compatible = "qcom,qfprom", "syscon"; - reg = <0x700000 0x1000>; - #address-cells = <1>; - #size-cells = <1>; - status = "okay"; - tsens_calib: calib@400 { - reg = <0x400 0xb>; - }; - tsens_backup: backup@410 { - reg = <0x410 0xb>; - }; - speedbin_efuse: speedbin@0c0 { - reg = <0x0c0 0x4>; - }; - }; - - rpm@108000 { - compatible = "qcom,rpm-ipq8064"; - reg = <0x108000 0x1000>; - qcom,ipc = <&l2cc 0x8 2>; - - interrupts = , - , - ; - interrupt-names = "ack", - "err", - "wakeup"; - - clocks = <&gcc RPM_MSG_RAM_H_CLK>; - clock-names = "ram"; - - #address-cells = <1>; - #size-cells = <0>; - - rpmcc: clock-controller { - compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc"; - #clock-cells = <1>; - }; - - regulators { - compatible = "qcom,rpm-smb208-regulators"; - - smb208_s1a: s1a { - regulator-min-microvolt = <1050000>; - regulator-max-microvolt = <1150000>; - - qcom,switch-mode-frequency = <1200000>; - - }; - - smb208_s1b: s1b { - regulator-min-microvolt = <1050000>; - regulator-max-microvolt = <1150000>; - - qcom,switch-mode-frequency = <1200000>; - }; - - smb208_s2a: s2a { - regulator-min-microvolt = < 800000>; - regulator-max-microvolt = <1250000>; - - qcom,switch-mode-frequency = <1200000>; - }; - - smb208_s2b: s2b { - regulator-min-microvolt = < 800000>; - regulator-max-microvolt = <1250000>; - - qcom,switch-mode-frequency = <1200000>; - }; - }; - }; - - rng@1a500000 { - compatible = "qcom,prng"; - reg = <0x1a500000 0x200>; - clocks = <&gcc PRNG_CLK>; - clock-names = "core"; - }; - - qcom_pinmux: pinmux@800000 { - compatible = "qcom,ipq8064-pinctrl"; - reg = <0x800000 0x4000>; - - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - interrupts = ; - - pcie0_pins: pcie0_pinmux { - mux { - pins = "gpio3"; - function = "pcie1_rst"; - drive-strength = <12>; - bias-disable; - }; - }; - - pcie1_pins: pcie1_pinmux { - mux { - pins = "gpio48"; - function = "pcie2_rst"; - drive-strength = <12>; - bias-disable; - }; - }; - - pcie2_pins: pcie2_pinmux { - mux { - pins = "gpio63"; - function = "pcie3_rst"; - drive-strength = <12>; - bias-disable; - output-low; - }; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - drive-strength = <10>; - bias-none; - }; - }; - - leds_pins: leds_pins { - mux { - pins = "gpio7", "gpio8", "gpio9", - "gpio26", "gpio53"; - function = "gpio"; - drive-strength = <2>; - bias-pull-down; - output-low; - }; - }; - - buttons_pins: buttons_pins { - mux { - pins = "gpio54"; - drive-strength = <2>; - bias-pull-up; - }; - }; - }; - - intc: interrupt-controller@2000000 { - compatible = "qcom,msm-qgic2"; - interrupt-controller; - #interrupt-cells = <3>; - reg = <0x02000000 0x1000>, - <0x02002000 0x1000>; - }; - - timer@200a000 { - compatible = "qcom,kpss-timer", - "qcom,kpss-wdt-ipq8064", "qcom,msm-timer"; - interrupts = , - , - , - , - ; - reg = <0x0200a000 0x100>; - clock-frequency = <25000000>, - <32768>; - clocks = <&sleep_clk>; - clock-names = "sleep"; - cpu-offset = <0x80000>; - }; - - acpu0_aux: clock-controller@2088000 { - compatible = "qcom,kpss-acc-v1"; - reg = <0x02088000 0x1000>, <0x02008000 0x1000>; - clock-output-names = "acpu0_aux"; - }; - - acpu1_aux: clock-controller@2098000 { - compatible = "qcom,kpss-acc-v1"; - reg = <0x02098000 0x1000>, <0x02008000 0x1000>; - clock-output-names = "acpu1_aux"; - }; - - l2cc: clock-controller@2011000 { - compatible = "qcom,kpss-gcc", "syscon"; - reg = <0x2011000 0x1000>; - clock-output-names = "acpu_l2_aux"; - }; - - kraitcc: clock-controller { - compatible = "qcom,krait-cc-v1"; - #clock-cells = <1>; - }; - - saw0: regulator@2089000 { - compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon"; - reg = <0x02089000 0x1000>, <0x02009000 0x1000>; - regulator; - }; - - saw1: regulator@2099000 { - compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon"; - reg = <0x02099000 0x1000>, <0x02009000 0x1000>; - regulator; - }; - - saw_l2: regulator@02012000 { - compatible = "qcom,saw2", "syscon"; - reg = <0x02012000 0x1000>; - regulator; - }; - - sic_non_secure: sic-non-secure@12100000 { - compatible = "syscon"; - reg = <0x12100000 0x10000>; - }; - - gsbi2: gsbi@12480000 { - compatible = "qcom,gsbi-v1.0.0"; - cell-index = <2>; - reg = <0x12480000 0x100>; - clocks = <&gcc GSBI2_H_CLK>; - clock-names = "iface"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - status = "disabled"; - - syscon-tcsr = <&tcsr>; - - gsbi2_serial: serial@12490000 { - compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; - reg = <0x12490000 0x1000>, - <0x12480000 0x1000>; - interrupts = ; - clocks = <&gcc GSBI2_UART_CLK>, <&gcc GSBI2_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - }; - - i2c@124a0000 { - compatible = "qcom,i2c-qup-v1.1.1"; - reg = <0x124a0000 0x1000>; - interrupts = ; - - clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - - #address-cells = <1>; - #size-cells = <0>; - }; - - }; - - gsbi4: gsbi@16300000 { - compatible = "qcom,gsbi-v1.0.0"; - cell-index = <4>; - reg = <0x16300000 0x100>; - clocks = <&gcc GSBI4_H_CLK>; - clock-names = "iface"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - status = "disabled"; - - syscon-tcsr = <&tcsr>; - - gsbi4_serial: serial@16340000 { - compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; - reg = <0x16340000 0x1000>, - <0x16300000 0x1000>; - interrupts = ; - clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - }; - - i2c@16380000 { - compatible = "qcom,i2c-qup-v1.1.1"; - reg = <0x16380000 0x1000>; - interrupts = ; - - clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - - #address-cells = <1>; - #size-cells = <0>; - }; - }; - - gsbi5: gsbi@1a200000 { - compatible = "qcom,gsbi-v1.0.0"; - cell-index = <5>; - reg = <0x1a200000 0x100>; - clocks = <&gcc GSBI5_H_CLK>; - clock-names = "iface"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - status = "disabled"; - - syscon-tcsr = <&tcsr>; - - gsbi5_serial: serial@1a240000 { - compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; - reg = <0x1a240000 0x1000>, - <0x1a200000 0x1000>; - interrupts = ; - clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - }; - - i2c@1a280000 { - compatible = "qcom,i2c-qup-v1.1.1"; - reg = <0x1a280000 0x1000>; - interrupts = ; - - clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - - #address-cells = <1>; - #size-cells = <0>; - }; - - spi@1a280000 { - compatible = "qcom,spi-qup-v1.1.1"; - reg = <0x1a280000 0x1000>; - interrupts = ; - - clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - - #address-cells = <1>; - #size-cells = <0>; - }; - }; - - gsbi7: gsbi@16600000 { - status = "disabled"; - compatible = "qcom,gsbi-v1.0.0"; - cell-index = <7>; - reg = <0x16600000 0x100>; - clocks = <&gcc GSBI7_H_CLK>; - clock-names = "iface"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - syscon-tcsr = <&tcsr>; - - gsbi7_serial: serial@16640000 { - compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; - reg = <0x16640000 0x1000>, - <0x16600000 0x1000>; - interrupts = ; - clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - }; - }; - - sata_phy: sata-phy@1b400000 { - compatible = "qcom,ipq806x-sata-phy"; - reg = <0x1b400000 0x200>; - - clocks = <&gcc SATA_PHY_CFG_CLK>; - clock-names = "cfg"; - - #phy-cells = <0>; - status = "disabled"; - }; - - sata: sata@29000000 { - compatible = "qcom,ipq806x-ahci", "generic-ahci"; - reg = <0x29000000 0x180>; - - ports-implemented = <0x1>; - - interrupts = ; - - clocks = <&gcc SFAB_SATA_S_H_CLK>, - <&gcc SATA_H_CLK>, - <&gcc SATA_A_CLK>, - <&gcc SATA_RXOOB_CLK>, - <&gcc SATA_PMALIVE_CLK>; - clock-names = "slave_face", "iface", "core", - "rxoob", "pmalive"; - - assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>; - assigned-clock-rates = <100000000>, <100000000>; - - phys = <&sata_phy>; - phy-names = "sata-phy"; - status = "disabled"; - }; - - qcom,ssbi@500000 { - compatible = "qcom,ssbi"; - reg = <0x00500000 0x1000>; - qcom,controller-type = "pmic-arbiter"; - }; - - gcc: clock-controller@900000 { - compatible = "qcom,gcc-ipq8064"; - reg = <0x00900000 0x4000>; - #clock-cells = <1>; - #reset-cells = <1>; - #power-domain-cells = <1>; - }; - - tsens: thermal-sensor@900000 { - compatible = "qcom,ipq8064-tsens"; - reg = <0x900000 0x3680>; - nvmem-cells = <&tsens_calib>, <&tsens_backup>; - nvmem-cell-names = "calib", "calib_backup"; - interrupts = ; - #thermal-sensor-cells = <1>; - }; - - tcsr: syscon@1a400000 { - compatible = "qcom,tcsr-ipq8064", "syscon"; - reg = <0x1a400000 0x100>; - }; - - lcc: clock-controller@28000000 { - compatible = "qcom,lcc-ipq8064"; - reg = <0x28000000 0x1000>; - #clock-cells = <1>; - #reset-cells = <1>; - }; - - sfpb_mutex_block: syscon@1200600 { - compatible = "syscon"; - reg = <0x01200600 0x100>; - }; - - hs_phy_0: hs_phy_0 { - compatible = "qcom,dwc3-hs-usb-phy"; - regmap = <&usb3_0>; - clocks = <&gcc USB30_0_UTMI_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - }; - - ss_phy_0: ss_phy_0 { - compatible = "qcom,dwc3-ss-usb-phy"; - regmap = <&usb3_0>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - }; - - usb3_0: usb3@110f8800 { - compatible = "qcom,dwc3", "syscon"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0x110f8800 0x8000>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "core"; - - ranges; - - resets = <&gcc USB30_0_MASTER_RESET>; - reset-names = "master"; - - status = "disabled"; - - dwc3_0: dwc3@11000000 { - compatible = "snps,dwc3"; - reg = <0x11000000 0xcd00>; - interrupts = ; - phys = <&hs_phy_0>, <&ss_phy_0>; - phy-names = "usb2-phy", "usb3-phy"; - dr_mode = "host"; - snps,dis_u3_susphy_quirk; - }; - }; - - hs_phy_1: hs_phy_1 { - compatible = "qcom,dwc3-hs-usb-phy"; - regmap = <&usb3_1>; - clocks = <&gcc USB30_1_UTMI_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - }; - - ss_phy_1: ss_phy_1 { - compatible = "qcom,dwc3-ss-usb-phy"; - regmap = <&usb3_1>; - clocks = <&gcc USB30_1_MASTER_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - }; - - usb3_1: usb3@100f8800 { - compatible = "qcom,dwc3", "syscon"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0x100f8800 0x8000>; - clocks = <&gcc USB30_1_MASTER_CLK>; - clock-names = "core"; - - ranges; - - resets = <&gcc USB30_1_MASTER_RESET>; - reset-names = "master"; - - status = "disabled"; - - dwc3_1: dwc3@10000000 { - compatible = "snps,dwc3"; - reg = <0x10000000 0xcd00>; - interrupts = ; - phys = <&hs_phy_1>, <&ss_phy_1>; - phy-names = "usb2-phy", "usb3-phy"; - dr_mode = "host"; - snps,dis_u3_susphy_quirk; - }; - }; - - pcie0: pci@1b500000 { - compatible = "qcom,pcie-ipq8064"; - reg = <0x1b500000 0x1000 - 0x1b502000 0x80 - 0x1b600000 0x100 - 0x0ff00000 0x100000>; - reg-names = "dbi", "elbi", "parf", "config"; - device_type = "pci"; - linux,pci-domain = <0>; - bus-range = <0x00 0xff>; - num-lanes = <1>; - #address-cells = <3>; - #size-cells = <2>; - - ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000 /* downstream I/O */ - 0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */ - - interrupts = ; - interrupt-names = "msi"; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0x7>; - interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ - <0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ - <0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ - <0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ - - clocks = <&gcc PCIE_A_CLK>, - <&gcc PCIE_H_CLK>, - <&gcc PCIE_PHY_CLK>, - <&gcc PCIE_AUX_CLK>, - <&gcc PCIE_ALT_REF_CLK>; - clock-names = "core", "iface", "phy", "aux", "ref"; - - assigned-clocks = <&gcc PCIE_ALT_REF_CLK>; - assigned-clock-rates = <100000000>; - - resets = <&gcc PCIE_ACLK_RESET>, - <&gcc PCIE_HCLK_RESET>, - <&gcc PCIE_POR_RESET>, - <&gcc PCIE_PCI_RESET>, - <&gcc PCIE_PHY_RESET>, - <&gcc PCIE_EXT_RESET>; - reset-names = "axi", "ahb", "por", "pci", "phy", "ext"; - - pinctrl-0 = <&pcie0_pins>; - pinctrl-names = "default"; - - perst-gpios = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>; - - phy-tx0-term-offset = <7>; - - status = "disabled"; - }; - - pcie1: pci@1b700000 { - compatible = "qcom,pcie-ipq8064"; - reg = <0x1b700000 0x1000 - 0x1b702000 0x80 - 0x1b800000 0x100 - 0x31f00000 0x100000>; - reg-names = "dbi", "elbi", "parf", "config"; - device_type = "pci"; - linux,pci-domain = <1>; - bus-range = <0x00 0xff>; - num-lanes = <1>; - #address-cells = <3>; - #size-cells = <2>; - - ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000 /* downstream I/O */ - 0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */ - - interrupts = ; - interrupt-names = "msi"; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0x7>; - interrupt-map = <0 0 0 1 &intc 0 58 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ - <0 0 0 2 &intc 0 59 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ - <0 0 0 3 &intc 0 60 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ - <0 0 0 4 &intc 0 61 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ - - clocks = <&gcc PCIE_1_A_CLK>, - <&gcc PCIE_1_H_CLK>, - <&gcc PCIE_1_PHY_CLK>, - <&gcc PCIE_1_AUX_CLK>, - <&gcc PCIE_1_ALT_REF_CLK>; - clock-names = "core", "iface", "phy", "aux", "ref"; - - assigned-clocks = <&gcc PCIE_1_ALT_REF_CLK>; - assigned-clock-rates = <100000000>; - - resets = <&gcc PCIE_1_ACLK_RESET>, - <&gcc PCIE_1_HCLK_RESET>, - <&gcc PCIE_1_POR_RESET>, - <&gcc PCIE_1_PCI_RESET>, - <&gcc PCIE_1_PHY_RESET>, - <&gcc PCIE_1_EXT_RESET>; - reset-names = "axi", "ahb", "por", "pci", "phy", "ext"; - - pinctrl-0 = <&pcie1_pins>; - pinctrl-names = "default"; - - perst-gpios = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>; - - phy-tx0-term-offset = <7>; - - status = "disabled"; - }; - - pcie2: pci@1b900000 { - compatible = "qcom,pcie-ipq8064"; - reg = <0x1b900000 0x1000 - 0x1b902000 0x80 - 0x1ba00000 0x100 - 0x35f00000 0x100000>; - reg-names = "dbi", "elbi", "parf", "config"; - device_type = "pci"; - linux,pci-domain = <2>; - bus-range = <0x00 0xff>; - num-lanes = <1>; - #address-cells = <3>; - #size-cells = <2>; - - ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000 /* downstream I/O */ - 0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */ - - interrupts = ; - interrupt-names = "msi"; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0x7>; - interrupt-map = <0 0 0 1 &intc 0 72 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ - <0 0 0 2 &intc 0 73 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ - <0 0 0 3 &intc 0 74 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ - <0 0 0 4 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ - - clocks = <&gcc PCIE_2_A_CLK>, - <&gcc PCIE_2_H_CLK>, - <&gcc PCIE_2_PHY_CLK>, - <&gcc PCIE_2_AUX_CLK>, - <&gcc PCIE_2_ALT_REF_CLK>; - clock-names = "core", "iface", "phy", "aux", "ref"; - - assigned-clocks = <&gcc PCIE_2_ALT_REF_CLK>; - assigned-clock-rates = <100000000>; - - resets = <&gcc PCIE_2_ACLK_RESET>, - <&gcc PCIE_2_HCLK_RESET>, - <&gcc PCIE_2_POR_RESET>, - <&gcc PCIE_2_PCI_RESET>, - <&gcc PCIE_2_PHY_RESET>, - <&gcc PCIE_2_EXT_RESET>; - reset-names = "axi", "ahb", "por", "pci", "phy", "ext"; - - pinctrl-0 = <&pcie2_pins>; - pinctrl-names = "default"; - - perst-gpios = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>; - - phy-tx0-term-offset = <7>; - - status = "disabled"; - }; - - adm_dma: dma@18300000 { - compatible = "qcom,adm"; - reg = <0x18300000 0x100000>; - interrupts = ; - #dma-cells = <1>; - - clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>; - clock-names = "core", "iface"; - - resets = <&gcc ADM0_RESET>, - <&gcc ADM0_PBUS_RESET>, - <&gcc ADM0_C0_RESET>, - <&gcc ADM0_C1_RESET>, - <&gcc ADM0_C2_RESET>; - reset-names = "clk", "pbus", "c0", "c1", "c2"; - qcom,ee = <0>; - - status = "disabled"; - }; - - nand: nand@1ac00000 { - compatible = "qcom,ipq806x-nand"; - reg = <0x1ac00000 0x800>; - - clocks = <&gcc EBI2_CLK>, - <&gcc EBI2_AON_CLK>; - clock-names = "core", "aon"; - - dmas = <&adm_dma 3>; - dma-names = "rxtx"; - qcom,cmd-crci = <15>; - qcom,data-crci = <3>; - - status = "disabled"; - - #address-cells = <1>; - #size-cells = <0>; - }; - - nss_common: syscon@03000000 { - compatible = "syscon"; - reg = <0x03000000 0x0000FFFF>; - }; - - qsgmii_csr: syscon@1bb00000 { - compatible = "syscon"; - reg = <0x1bb00000 0x000001FF>; - }; - - stmmac_axi_setup: stmmac-axi-config { - snps,wr_osr_lmt = <7>; - snps,rd_osr_lmt = <7>; - snps,blen = <16 0 0 0 0 0 0>; - }; - - gmac0: ethernet@37000000 { - device_type = "network"; - compatible = "qcom,ipq806x-gmac"; - reg = <0x37000000 0x200000>; - interrupts = ; - interrupt-names = "macirq"; - - snps,axi-config = <&stmmac_axi_setup>; - snps,pbl = <32>; - snps,aal = <1>; - - qcom,nss-common = <&nss_common>; - qcom,qsgmii-csr = <&qsgmii_csr>; - - clocks = <&gcc GMAC_CORE1_CLK>; - clock-names = "stmmaceth"; - - resets = <&gcc GMAC_CORE1_RESET>; - reset-names = "stmmaceth"; - - status = "disabled"; - }; - - gmac1: ethernet@37200000 { - device_type = "network"; - compatible = "qcom,ipq806x-gmac"; - reg = <0x37200000 0x200000>; - interrupts = ; - interrupt-names = "macirq"; - - snps,axi-config = <&stmmac_axi_setup>; - snps,pbl = <32>; - snps,aal = <1>; - - qcom,nss-common = <&nss_common>; - qcom,qsgmii-csr = <&qsgmii_csr>; - - clocks = <&gcc GMAC_CORE2_CLK>; - clock-names = "stmmaceth"; - - resets = <&gcc GMAC_CORE2_RESET>; - reset-names = "stmmaceth"; - - status = "disabled"; - }; - - gmac2: ethernet@37400000 { - device_type = "network"; - compatible = "qcom,ipq806x-gmac"; - reg = <0x37400000 0x200000>; - interrupts = ; - interrupt-names = "macirq"; - - snps,axi-config = <&stmmac_axi_setup>; - snps,pbl = <32>; - snps,aal = <1>; - - qcom,nss-common = <&nss_common>; - qcom,qsgmii-csr = <&qsgmii_csr>; - - clocks = <&gcc GMAC_CORE3_CLK>; - clock-names = "stmmaceth"; - - resets = <&gcc GMAC_CORE3_RESET>; - reset-names = "stmmaceth"; - - status = "disabled"; - }; - - gmac3: ethernet@37600000 { - device_type = "network"; - compatible = "qcom,ipq806x-gmac"; - reg = <0x37600000 0x200000>; - interrupts = ; - interrupt-names = "macirq"; - - snps,axi-config = <&stmmac_axi_setup>; - snps,pbl = <32>; - snps,aal = <1>; - - qcom,nss-common = <&nss_common>; - qcom,qsgmii-csr = <&qsgmii_csr>; - - clocks = <&gcc GMAC_CORE4_CLK>; - clock-names = "stmmaceth"; - - resets = <&gcc GMAC_CORE4_RESET>; - reset-names = "stmmaceth"; - - status = "disabled"; - }; - - /* Temporary fixed regulator */ - vsdcc_fixed: vsdcc-regulator { - compatible = "regulator-fixed"; - regulator-name = "SDCC Power"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - sdcc1bam:dma@12402000 { - compatible = "qcom,bam-v1.3.0"; - reg = <0x12402000 0x8000>; - interrupts = ; - clocks = <&gcc SDC1_H_CLK>; - clock-names = "bam_clk"; - #dma-cells = <1>; - qcom,ee = <0>; - }; - - sdcc3bam:dma@12182000 { - compatible = "qcom,bam-v1.3.0"; - reg = <0x12182000 0x8000>; - interrupts = ; - clocks = <&gcc SDC3_H_CLK>; - clock-names = "bam_clk"; - #dma-cells = <1>; - qcom,ee = <0>; - }; - - amba { - compatible = "arm,amba-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - sdcc1: sdcc@12400000 { - status = "disabled"; - compatible = "arm,pl18x", "arm,primecell"; - arm,primecell-periphid = <0x00051180>; - reg = <0x12400000 0x2000>; - interrupts = ; - interrupt-names = "cmd_irq"; - clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>; - clock-names = "mclk", "apb_pclk"; - bus-width = <8>; - max-frequency = <96000000>; - non-removable; - cap-sd-highspeed; - cap-mmc-highspeed; - vmmc-supply = <&vsdcc_fixed>; - dmas = <&sdcc1bam 2>, <&sdcc1bam 1>; - dma-names = "tx", "rx"; - }; - - sdcc3: sdcc@12180000 { - compatible = "arm,pl18x", "arm,primecell"; - arm,primecell-periphid = <0x00051180>; - status = "disabled"; - reg = <0x12180000 0x2000>; - interrupts = ; - interrupt-names = "cmd_irq"; - clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>; - clock-names = "mclk", "apb_pclk"; - bus-width = <8>; - cap-sd-highspeed; - cap-mmc-highspeed; - max-frequency = <192000000>; - #mmc-ddr-1_8v; - sd-uhs-sdr104; - sd-uhs-ddr50; - vqmmc-supply = <&vsdcc_fixed>; - dmas = <&sdcc3bam 2>, <&sdcc3bam 1>; - dma-names = "tx", "rx"; - }; - }; - }; - - sfpb_mutex: sfpb-mutex { - compatible = "qcom,sfpb-mutex"; - syscon = <&sfpb_mutex_block 4 4>; - - #hwlock-cells = <1>; - }; - - smem { - compatible = "qcom,smem"; - memory-region = <&smem>; - hwlocks = <&sfpb_mutex 3>; - }; -}; diff --git a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts b/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts deleted file mode 100644 index 2cff2f65bc..0000000000 --- a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts +++ /dev/null @@ -1,371 +0,0 @@ -#include "qcom-ipq8065.dtsi" - -#include - -/ { - model = "ZyXEL NBG6817"; - compatible = "zyxel,nbg6817", "qcom,ipq8065", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - mdio-gpio0 = &mdio0; - sdcc1 = &sdcc1; - - led-boot = &power; - led-failsafe = &power; - led-running = &power; - led-upgrade = &power; - }; - - chosen { - bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd"; - stdout-path = "serial0:115200n8"; - append-rootblock = "root=/dev/mmcblk0p"; - }; - - soc { - pinmux@800000 { - button_pins: button_pins { - mux { - pins = "gpio53", "gpio54", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - i2c4_pins: i2c4_pinmux { - mux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - drive-strength = <12>; - bias-disable; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio9", "gpio26", "gpio33", "gpio64"; - function = "gpio"; - drive-strength = <2>; - bias-pull-down; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - - clk { - pins = "gpio1"; - input-disable; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - - tx { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ; - input-disable; - }; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - drive-strength = <10>; - bias-none; - }; - - cs { - pins = "gpio20"; - drive-strength = <12>; - }; - }; - - usb0_pwr_en_pins: usb0_pwr_en_pins { - mux { - pins = "gpio16", "gpio17"; - function = "gpio"; - drive-strength = <12>; - }; - - pwr { - pins = "gpio17"; - bias-pull-down; - output-high; - }; - - ovc { - pins = "gpio16"; - bias-pull-up; - }; - }; - - usb1_pwr_en_pins: usb1_pwr_en_pins { - mux { - pins = "gpio14", "gpio15"; - function = "gpio"; - drive-strength = <12>; - }; - - pwr { - pins = "gpio14"; - bias-pull-down; - output-high; - }; - - ovc { - pins = "gpio15"; - bias-pull-up; - }; - }; - }; - - gsbi@16300000 { - qcom,mode = ; - status = "okay"; - serial@16340000 { - status = "okay"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ - }; - - gsbi5: gsbi@1a200000 { - qcom,mode = ; - status = "okay"; - - spi4: spi@1a280000 { - status = "okay"; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; - - flash: m25p80@0 { - compatible = "jedec,spi-nor"; - #address-cells = <1>; - #size-cells = <1>; - spi-max-frequency = <51200000>; - reg = <0>; - - partitions { - compatible = "qcom,smem"; - }; - }; - }; - }; - - usb3_0: usb3@110f8800 { - status = "okay"; - - pinctrl-0 = <&usb0_pwr_en_pins>; - pinctrl-names = "default"; - }; - - usb3_1: usb3@100f8800 { - status = "okay"; - - pinctrl-0 = <&usb1_pwr_en_pins>; - pinctrl-names = "default"; - }; - - pcie0: pci@1b500000 { - status = "okay"; - reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>; - pinctrl-0 = <&pcie0_pins>; - pinctrl-names = "default"; - }; - - pcie1: pci@1b700000 { - status = "okay"; - reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>; - pinctrl-0 = <&pcie1_pins>; - pinctrl-names = "default"; - force_gen1 = <1>; - }; - - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, - <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0xaa545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - 0x00970 0x1e864443 /* QM_PORT0_CTRL0 */ - 0x00974 0x000001c6 /* QM_PORT0_CTRL1 */ - 0x00978 0x19008643 /* QM_PORT1_CTRL0 */ - 0x0097c 0x000001c6 /* QM_PORT1_CTRL1 */ - 0x00980 0x19008643 /* QM_PORT2_CTRL0 */ - 0x00984 0x000001c6 /* QM_PORT2_CTRL1 */ - 0x00988 0x19008643 /* QM_PORT3_CTRL0 */ - 0x0098c 0x000001c6 /* QM_PORT3_CTRL1 */ - 0x00990 0x19008643 /* QM_PORT4_CTRL0 */ - 0x00994 0x000001c6 /* QM_PORT4_CTRL1 */ - 0x00998 0x1e864443 /* QM_PORT5_CTRL0 */ - 0x0099c 0x000001c6 /* QM_PORT5_CTRL1 */ - 0x009a0 0x1e864443 /* QM_PORT6_CTRL0 */ - 0x009a4 0x000001c6 /* QM_PORT6_CTRL1 */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - qca,ar8327-initvals = < - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x0000c 0x80 /* PAD6_MODE */ - >; - }; - }; - - gmac1: ethernet@37200000 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <1>; - qcom,phy_mdio_addr = <4>; - qcom,poll_required = <0>; - qcom,rgmii_delay = <1>; - qcom,phy_mii_type = <0>; - qcom,emulation = <0>; - qcom,irq = <255>; - mdiobus = <&mdio0>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - gmac2: ethernet@37400000 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - qcom,phy_mdio_addr = <0>; /* none */ - qcom,poll_required = <0>; /* no polling */ - qcom,rgmii_delay = <0>; - qcom,phy_mii_type = <1>; - qcom,emulation = <0>; - qcom,irq = <258>; - mdiobus = <&mdio0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - amba { - sdcc1: sdcc@12400000 { - status = "okay"; - }; - }; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_LOW>; - linux,code = ; - linux,input-type = ; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - internet { - label = "white:internet"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; - }; - - power: power { - label = "white:power"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - wifi2g { - label = "amber:wifi2g"; - gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>; - }; - - /* wifi2g amber from the manual is missing */ - - wifi5g { - label = "amber:wifi5g"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; - }; - - /* wifi5g amber from the manual is missing */ - }; -}; - -&adm_dma { - status = "okay"; -}; diff --git a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8065-r7800.dts b/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8065-r7800.dts deleted file mode 100644 index 50ffcdab07..0000000000 --- a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8065-r7800.dts +++ /dev/null @@ -1,531 +0,0 @@ -#include "qcom-ipq8065.dtsi" - -#include - -/ { - model = "Netgear Nighthawk X4S R7800"; - compatible = "netgear,r7800", "qcom,ipq8065", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - - rsvd@5fe00000 { - reg = <0x5fe00000 0x200000>; - reusable; - }; - }; - - aliases { - serial0 = &gsbi4_serial; - mdio-gpio0 = &mdio0; - - led-boot = &power_white; - led-failsafe = &power_amber; - led-running = &power_white; - led-upgrade = &power_amber; - label-mac-device = &gmac2; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - soc { - pinmux@800000 { - button_pins: button_pins { - mux { - pins = "gpio6", "gpio54", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - i2c4_pins: i2c4_pinmux { - mux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - drive-strength = <12>; - bias-disable; - }; - }; - - led_pins: led_pins { - pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23", - "gpio24","gpio26", "gpio53", "gpio64"; - function = "gpio"; - drive-strength = <2>; - bias-pull-down; - }; - - nand_pins: nand_pins { - disable { - pins = "gpio34", "gpio35", "gpio36", - "gpio37", "gpio38"; - function = "nand"; - drive-strength = <10>; - bias-disable; - }; - - pullups { - pins = "gpio39"; - function = "nand"; - drive-strength = <10>; - bias-pull-up; - }; - - hold { - pins = "gpio40", "gpio41", "gpio42", - "gpio43", "gpio44", "gpio45", - "gpio46", "gpio47"; - function = "nand"; - drive-strength = <10>; - bias-bus-hold; - }; - }; - - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - - clk { - pins = "gpio1"; - input-disable; - }; - }; - - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; - function = "rgmii2"; - drive-strength = <8>; - bias-disable; - }; - - tx { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ; - input-disable; - }; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - bias-pull-down; - }; - - data { - pins = "gpio18", "gpio19"; - drive-strength = <10>; - }; - - cs { - pins = "gpio20"; - drive-strength = <10>; - bias-pull-up; - }; - - clk { - pins = "gpio21"; - drive-strength = <12>; - }; - }; - - spi6_pins: spi6_pins { - mux { - pins = "gpio55", "gpio56", "gpio58"; - function = "gsbi6"; - bias-pull-down; - }; - - mosi { - pins = "gpio55"; - drive-strength = <12>; - }; - - miso { - pins = "gpio56"; - drive-strength = <14>; - }; - - cs { - pins = "gpio57"; - drive-strength = <12>; - bias-pull-up; - }; - - clk { - pins = "gpio58"; - drive-strength = <12>; - }; - - reset { - pins = "gpio33"; - drive-strength = <10>; - bias-pull-down; - output-high; - }; - }; - - usb0_pwr_en_pins: usb0_pwr_en_pins { - mux { - pins = "gpio15"; - function = "gpio"; - drive-strength = <12>; - bias-pull-down; - output-high; - }; - }; - - usb1_pwr_en_pins: usb1_pwr_en_pins { - mux { - pins = "gpio16", "gpio68"; - function = "gpio"; - drive-strength = <12>; - bias-pull-down; - output-high; - }; - }; - }; - - gsbi@16300000 { - qcom,mode = ; - status = "okay"; - serial@16340000 { - status = "okay"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ - }; - - sata-phy@1b400000 { - status = "okay"; - }; - - sata@29000000 { - ports-implemented = <0x1>; - status = "okay"; - }; - - usb3_0: usb3@110f8800 { - status = "okay"; - - pinctrl-0 = <&usb0_pwr_en_pins>; - pinctrl-names = "default"; - }; - - usb3_1: usb3@100f8800 { - status = "okay"; - - pinctrl-0 = <&usb1_pwr_en_pins>; - pinctrl-names = "default"; - }; - - pcie0: pci@1b500000 { - status = "okay"; - - bridge@0,0 { - reg = <0x00000000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - ranges; - - wifi@1,0 { - compatible = "pci168c,0046"; - reg = <0x00010000 0 0 0 0>; - - mtd-mac-address = <&art 6>; - mtd-mac-address-increment = <(1)>; - }; - }; - }; - - pcie1: pci@1b700000 { - status = "okay"; - force_gen1 = <1>; - - bridge@0,0 { - reg = <0x00000000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - ranges; - - wifi@1,0 { - compatible = "pci168c,0046"; - reg = <0x00010000 0 0 0 0>; - - mtd-mac-address = <&art 6>; - mtd-mac-address-increment = <(2)>; - }; - }; - }; - - nand@1ac00000 { - status = "okay"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - cs0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - qcadata@0 { - label = "qcadata"; - reg = <0x0000000 0x0c80000>; - read-only; - }; - - APPSBL@c80000 { - label = "APPSBL"; - reg = <0x0c80000 0x0500000>; - read-only; - }; - - APPSBLENV@1180000 { - label = "APPSBLENV"; - reg = <0x1180000 0x0080000>; - read-only; - }; - - art: art@1200000 { - label = "art"; - reg = <0x1200000 0x0140000>; - read-only; - }; - - artbak: art@1340000 { - label = "artbak"; - reg = <0x1340000 0x0140000>; - read-only; - }; - - kernel@1480000 { - label = "kernel"; - reg = <0x1480000 0x0400000>; - }; - - ubi@1880000 { - label = "ubi"; - reg = <0x1880000 0x6080000>; - }; - - reserve@7900000 { - label = "reserve"; - reg = <0x7900000 0x0700000>; - read-only; - }; - }; - }; - }; - - mdio0: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, - <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0xaa545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - 0x00970 0x1e864443 /* QM_PORT0_CTRL0 */ - 0x00974 0x000001c6 /* QM_PORT0_CTRL1 */ - 0x00978 0x19008643 /* QM_PORT1_CTRL0 */ - 0x0097c 0x000001c6 /* QM_PORT1_CTRL1 */ - 0x00980 0x19008643 /* QM_PORT2_CTRL0 */ - 0x00984 0x000001c6 /* QM_PORT2_CTRL1 */ - 0x00988 0x19008643 /* QM_PORT3_CTRL0 */ - 0x0098c 0x000001c6 /* QM_PORT3_CTRL1 */ - 0x00990 0x19008643 /* QM_PORT4_CTRL0 */ - 0x00994 0x000001c6 /* QM_PORT4_CTRL1 */ - 0x00998 0x1e864443 /* QM_PORT5_CTRL0 */ - 0x0099c 0x000001c6 /* QM_PORT5_CTRL1 */ - 0x009a0 0x1e864443 /* QM_PORT6_CTRL0 */ - 0x009a4 0x000001c6 /* QM_PORT6_CTRL1 */ - >; - qca,ar8327-vlans = < - 0x1 0x5e /* VLAN1 Ports 1/2/3/4/6 */ - 0x2 0x21 /* VLAN2 Ports 0/5 */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - qca,ar8327-initvals = < - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x0000c 0x80 /* PAD6_MODE */ - >; - }; - }; - - gmac1: ethernet@37200000 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <1>; - qcom,phy_mdio_addr = <4>; - qcom,poll_required = <0>; - qcom,rgmii_delay = <1>; - qcom,phy_mii_type = <0>; - qcom,emulation = <0>; - qcom,irq = <255>; - mdiobus = <&mdio0>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&art 6>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - gmac2: ethernet@37400000 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - qcom,phy_mdio_addr = <0>; /* none */ - qcom,poll_required = <0>; /* no polling */ - qcom,rgmii_delay = <0>; - qcom,phy_mii_type = <1>; - qcom,emulation = <0>; - qcom,irq = <258>; - mdiobus = <&mdio0>; - - mtd-mac-address = <&art 0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; - linux,code = ; - debounce-interval = <60>; - wakeup-source; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = ; - debounce-interval = <60>; - wakeup-source; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = ; - debounce-interval = <60>; - wakeup-source; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - power_white: power_white { - label = "white:power"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - power_amber: power_amber { - label = "amber:power"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - wan_white { - label = "white:wan"; - gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; - }; - - wan_amber { - label = "amber:wan"; - gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; - }; - - usb1 { - label = "white:usb1"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - usb2 { - label = "white:usb2"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - esata { - label = "white:esata"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; - }; - - wifi { - label = "white:wifi"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; - }; - - wps { - label = "white:wps"; - gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&adm_dma { - status = "okay"; -}; diff --git a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8065.dtsi b/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8065.dtsi deleted file mode 100644 index fdd4697887..0000000000 --- a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8065.dtsi +++ /dev/null @@ -1,128 +0,0 @@ -#include "qcom-ipq8064-v2.0.dtsi" - -/ { - model = "Qualcomm IPQ8065"; - compatible = "qcom,ipq8065", "qcom,ipq8064"; - - soc: soc { - - rpm@108000 { - - regulators { - - smb208_s2a: s2a { - regulator-min-microvolt = <775000>; - regulator-max-microvolt = <1275000>; - }; - - smb208_s2b: s2b { - regulator-min-microvolt = <775000>; - regulator-max-microvolt = <1275000>; - }; - }; - }; - }; - - cpus { - qcom,l2 { - qcom,l2-cpufreq = <384000000 600000000 1400000000>; - }; - - idle-states { - CPU_SPC: spc { - status = "disabled"; - }; - }; - }; -}; - -&opp_table0 { - compatible = "operating-points-v2-qcom-cpu"; - nvmem-cells = <&speedbin_efuse>; - - /* - * On ipq8065 1.2 ghz freq is not present - * Remove it to make cpufreq work and not - * complain for missing definition - */ - - /delete-node/opp-1200000000; - - opp-384000000 { - opp-hz = /bits/ 64 <384000000>; - opp-microvolt-speed0-pvs0-v0 = <975000>; - opp-microvolt-speed0-pvs1-v0 = <950000>; - opp-microvolt-speed0-pvs2-v0 = <925000>; - opp-microvolt-speed0-pvs3-v0 = <900000>; - opp-microvolt-speed0-pvs4-v0 = <875000>; - opp-microvolt-speed0-pvs5-v0 = <825000>; - opp-microvolt-speed0-pvs6-v0 = <775000>; - opp-supported-hw = <0x1>; - clock-latency-ns = <100000>; - }; - - opp-600000000 { - opp-hz = /bits/ 64 <600000000>; - opp-microvolt-speed0-pvs0-v0 = <1000000>; - opp-microvolt-speed0-pvs1-v0 = <975000>; - opp-microvolt-speed0-pvs2-v0 = <950000>; - opp-microvolt-speed0-pvs3-v0 = <925000>; - opp-microvolt-speed0-pvs4-v0 = <900000>; - opp-microvolt-speed0-pvs5-v0 = <850000>; - opp-microvolt-speed0-pvs6-v0 = <800000>; - opp-supported-hw = <0x1>; - clock-latency-ns = <100000>; - }; - - opp-800000000 { - opp-hz = /bits/ 64 <800000000>; - opp-microvolt-speed0-pvs0-v0 = <1050000>; - opp-microvolt-speed0-pvs1-v0 = <1025000>; - opp-microvolt-speed0-pvs2-v0 = <1000000>; - opp-microvolt-speed0-pvs3-v0 = <975000>; - opp-microvolt-speed0-pvs4-v0 = <950000>; - opp-microvolt-speed0-pvs5-v0 = <900000>; - opp-microvolt-speed0-pvs6-v0 = <850000>; - opp-supported-hw = <0x1>; - clock-latency-ns = <100000>; - }; - - opp-1000000000 { - opp-hz = /bits/ 64 <1000000000>; - opp-microvolt-speed0-pvs0-v0 = <1100000>; - opp-microvolt-speed0-pvs1-v0 = <1075000>; - opp-microvolt-speed0-pvs2-v0 = <1050000>; - opp-microvolt-speed0-pvs3-v0 = <1025000>; - opp-microvolt-speed0-pvs4-v0 = <1000000>; - opp-microvolt-speed0-pvs5-v0 = <950000>; - opp-microvolt-speed0-pvs6-v0 = <900000>; - opp-supported-hw = <0x1>; - clock-latency-ns = <100000>; - }; - - opp-1400000000 { - opp-hz = /bits/ 64 <1400000000>; - opp-microvolt-speed0-pvs0-v0 = <1175000>; - opp-microvolt-speed0-pvs1-v0 = <1150000>; - opp-microvolt-speed0-pvs2-v0 = <1125000>; - opp-microvolt-speed0-pvs3-v0 = <1100000>; - opp-microvolt-speed0-pvs4-v0 = <1075000>; - opp-microvolt-speed0-pvs5-v0 = <1025000>; - opp-microvolt-speed0-pvs6-v0 = <975000>; - opp-supported-hw = <0x1>; - clock-latency-ns = <100000>; - }; - - opp-1725000000 { - opp-hz = /bits/ 64 <1725000000>; - opp-microvolt-speed0-pvs0-v0 = <1262500>; - opp-microvolt-speed0-pvs1-v0 = <1225000>; - opp-microvolt-speed0-pvs2-v0 = <1200000>; - opp-microvolt-speed0-pvs3-v0 = <1175000>; - opp-microvolt-speed0-pvs4-v0 = <1150000>; - opp-microvolt-speed0-pvs5-v0 = <1100000>; - opp-microvolt-speed0-pvs6-v0 = <1050000>; - opp-supported-hw = <0x1>; - clock-latency-ns = <100000>; - }; -}; diff --git a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-ap148.dts b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-ap148.dts deleted file mode 100644 index b2fdc427e2..0000000000 --- a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-ap148.dts +++ /dev/null @@ -1,121 +0,0 @@ -#include "qcom-ipq8064-v1.0.dtsi" - -/ { - model = "Qualcomm Technologies, Inc. IPQ8064/AP-148"; - compatible = "qcom,ipq8064-ap148", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - aliases { - mdio-gpio0 = &mdio0; - }; -}; - -&adm_dma { - status = "okay"; -}; - -&flash { - partitions { - compatible = "qcom,smem"; - }; -}; - -&usb3_0 { - status = "okay"; -}; - -&usb3_1 { - status = "okay"; -}; - -&pcie0 { - status = "okay"; -}; - -&pcie1 { - status = "okay"; - max-link-speed = <1>; -}; - -&nand_controller { - status = "okay"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - nand@0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "qcom,smem"; - }; - }; -}; - -&mdio0 { - status = "okay"; - - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - }; -}; - -&gmac1 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gmac2 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; diff --git a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-ap161.dts b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-ap161.dts deleted file mode 100644 index 6ba3d70808..0000000000 --- a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-ap161.dts +++ /dev/null @@ -1,159 +0,0 @@ -#include "qcom-ipq8064-v1.0.dtsi" - -/ { - model = "Qualcomm IPQ8064/AP161"; - compatible = "qcom,ipq8064-ap161", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - aliases { - mdio-gpio0 = &mdio0; - }; -}; - -&qcom_pinmux { - rgmii2_pins: rgmii2_pins { - mux { - pins = "gpio27", "gpio28", "gpio29", - "gpio30", "gpio31", "gpio32", - "gpio51", "gpio52", "gpio59", - "gpio60", "gpio61", "gpio62", - "gpio2", "gpio66"; - }; - }; -}; - -&flash { - partitions { - compatible = "qcom,smem"; - }; -}; - -&usb3_0 { - status = "okay"; -}; - -&usb3_1 { - status = "okay"; -}; - -&pcie0 { - status = "okay"; -}; - -&pcie1 { - status = "okay"; - max-link-speed = <1>; -}; - -&pcie2 { - status = "okay"; -}; - -&nand_controller { - status = "okay"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - nand@0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "qcom,smem"; - }; - }; -}; - -&mdio0 { - status = "okay"; - - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x20080 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - qca,phy-rgmii-en; - qca,txclk-delay-en; - qca,rxclk-delay-en; - }; - - phy3: ethernet-phy@3 { - device_type = "ethernet-phy"; - reg = <3>; - }; -}; - -&gmac0 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <0>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - mdiobus = <&mdio0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gmac1 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <1>; - mdiobus = <&mdio0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gmac2 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - mdiobus = <&mdio0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&adm_dma { - status = "okay"; -}; diff --git a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-c2600.dts b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-c2600.dts deleted file mode 100644 index 4ae7de604b..0000000000 --- a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-c2600.dts +++ /dev/null @@ -1,417 +0,0 @@ -#include "qcom-ipq8064-v2.0.dtsi" - -#include - -/ { - model = "TP-Link Archer C2600"; - compatible = "tplink,c2600", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - aliases { - mdio-gpio0 = &mdio0; - - led-boot = &power; - led-failsafe = &general; - led-running = &power; - led-upgrade = &general; - label-mac-device = &gmac2; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 49 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - ledswitch { - label = "ledswitch"; - gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - lan { - label = "white:lan"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_HIGH>; - }; - - usb4 { - label = "white:usb_4"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - usb2 { - label = "white:usb_2"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - wps { - label = "white:wps"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - wan_amber { - label = "amber:wan"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>; - }; - - wan_white { - label = "white:wan"; - gpios = <&qcom_pinmux 33 GPIO_ACTIVE_LOW>; - }; - - power: power { - label = "white:power"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - general: general { - label = "white:general"; - gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&qcom_pinmux { - button_pins: button_pins { - mux { - pins = "gpio16", "gpio54", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio26", "gpio33", - "gpio53", "gpio66"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - bias-pull-down; - }; - - data { - pins = "gpio18", "gpio19"; - drive-strength = <10>; - }; - - cs { - pins = "gpio20"; - function = "gpio"; - drive-strength = <10>; - bias-pull-up; - }; - - clk { - pins = "gpio21"; - drive-strength = <12>; - }; - }; - - usb0_pwr_en_pin: usb0_pwr_en_pin { - mux { - pins = "gpio25"; - function = "gpio"; - drive-strength = <10>; - bias-pull-up; - output-high; - }; - }; - - usb1_pwr_en_pin: usb1_pwr_en_pin { - mux { - pins = "gpio23"; - function = "gpio"; - drive-strength = <10>; - bias-pull-up; - output-high; - }; - }; -}; - -&gsbi5 { - qcom,mode = ; - status = "okay"; - - spi5: spi@1a280000 { - status = "okay"; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; - - m25p80@0 { - compatible = "jedec,spi-nor"; - #address-cells = <1>; - #size-cells = <1>; - spi-max-frequency = <50000000>; - reg = <0>; - - SBL1@0 { - label = "SBL1"; - reg = <0x0 0x20000>; - read-only; - }; - - MIBIB@20000 { - label = "MIBIB"; - reg = <0x20000 0x20000>; - read-only; - }; - - SBL2@40000 { - label = "SBL2"; - reg = <0x40000 0x20000>; - read-only; - }; - - SBL3@60000 { - label = "SBL3"; - reg = <0x60000 0x30000>; - read-only; - }; - - DDRCONFIG@90000 { - label = "DDRCONFIG"; - reg = <0x90000 0x10000>; - read-only; - }; - - SSD@a0000 { - label = "SSD"; - reg = <0xa0000 0x10000>; - read-only; - }; - - TZ@b0000 { - label = "TZ"; - reg = <0xb0000 0x30000>; - read-only; - }; - - RPM@e0000 { - label = "RPM"; - reg = <0xe0000 0x20000>; - read-only; - }; - - fs-uboot@100000 { - label = "fs-uboot"; - reg = <0x100000 0x70000>; - read-only; - }; - - uboot-env@170000 { - label = "uboot-env"; - reg = <0x170000 0x40000>; - read-only; - }; - - radio@1b0000 { - label = "radio"; - reg = <0x1b0000 0x40000>; - read-only; - }; - - os-image@1f0000 { - label = "os-image"; - reg = <0x1f0000 0x400000>; - }; - - rootfs@5f0000 { - label = "rootfs"; - reg = <0x5f0000 0x1900000>; - }; - - defaultmac: default-mac@1ef0000 { - label = "default-mac"; - reg = <0x1ef0000 0x00200>; - read-only; - }; - - pin@1ef0200 { - label = "pin"; - reg = <0x1ef0200 0x00200>; - read-only; - }; - - product-info@1ef0400 { - label = "product-info"; - reg = <0x1ef0400 0x0fc00>; - read-only; - }; - - partition-table@1f00000 { - label = "partition-table"; - reg = <0x1f00000 0x10000>; - read-only; - }; - - soft-version@1f10000 { - label = "soft-version"; - reg = <0x1f10000 0x10000>; - read-only; - }; - - support-list@1f20000 { - label = "support-list"; - reg = <0x1f20000 0x10000>; - read-only; - }; - - profile@1f30000 { - label = "profile"; - reg = <0x1f30000 0x10000>; - read-only; - }; - - default-config@1f40000 { - label = "default-config"; - reg = <0x1f40000 0x10000>; - read-only; - }; - - user-config@1f50000 { - label = "user-config"; - reg = <0x1f50000 0x40000>; - read-only; - }; - - qos-db@1f90000 { - label = "qos-db"; - reg = <0x1f90000 0x40000>; - read-only; - }; - - usb-config@1fd0000 { - label = "usb-config"; - reg = <0x1fd0000 0x10000>; - read-only; - }; - - log@1fe0000 { - label = "log"; - reg = <0x1fe0000 0x20000>; - read-only; - }; - }; - }; -}; - -&usb3_0 { - status = "okay"; - - pinctrl-0 = <&usb0_pwr_en_pin>; - pinctrl-names = "default"; -}; - -&usb3_1 { - status = "okay"; - - pinctrl-0 = <&usb1_pwr_en_pin>; - pinctrl-names = "default"; -}; - -&pcie0 { - status = "okay"; -}; - -&pcie1 { - status = "okay"; - max-link-speed = <1>; -}; - -&mdio0 { - status = "okay"; - - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - }; -}; - -&gmac1 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&defaultmac 0x8>; - mtd-mac-address-increment = <1>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gmac2 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - - mtd-mac-address = <&defaultmac 0x8>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&adm_dma { - status = "okay"; -}; diff --git a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-d7800.dts b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-d7800.dts deleted file mode 100644 index 7fb871be78..0000000000 --- a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-d7800.dts +++ /dev/null @@ -1,310 +0,0 @@ -#include "qcom-ipq8064-v2.0.dtsi" - -#include - -/ { - model = "Netgear Nighthawk X4 D7800"; - compatible = "netgear,d7800", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0xe000000>; - device_type = "memory"; - }; - - aliases { - mdio-gpio0 = &mdio0; - - led-boot = &power_white; - led-failsafe = &power_amber; - led-running = &power_white; - led-upgrade = &power_amber; - }; - - chosen { - bootargs = "rootfstype=squashfs noinitrd"; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - usb1 { - label = "white:usb1"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - usb2 { - label = "white:usb2"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - power_amber: power_amber { - label = "amber:power"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - wan_white { - label = "white:wan"; - gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; - }; - - wan_amber { - label = "amber:wan"; - gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; - }; - - wps { - label = "white:wps"; - gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; - }; - - esata { - label = "white:esata"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; - }; - - power_white: power_white { - label = "white:power"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - wifi { - label = "white:wifi"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&qcom_pinmux { - button_pins: button_pins { - mux { - pins = "gpio6", "gpio54", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23", - "gpio24","gpio26", "gpio53", "gpio64"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - usb0_pwr_en_pins: usb0_pwr_en_pins { - mux { - pins = "gpio15"; - function = "gpio"; - drive-strength = <12>; - bias-pull-down; - output-high; - }; - }; - - usb1_pwr_en_pins: usb1_pwr_en_pins { - mux { - pins = "gpio16", "gpio68"; - function = "gpio"; - drive-strength = <12>; - bias-pull-down; - output-high; - }; - }; -}; - -&sata_phy { - status = "okay"; -}; - -&sata { - status = "okay"; -}; - -&usb3_0 { - status = "okay"; - - pinctrl-0 = <&usb0_pwr_en_pins>; - pinctrl-names = "default"; -}; - -&usb3_1 { - status = "okay"; - - pinctrl-0 = <&usb1_pwr_en_pins>; - pinctrl-names = "default"; -}; - -&pcie0 { - status = "okay"; - reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&pcie0_pins>; - pinctrl-names = "default"; -}; - -&pcie1 { - status = "okay"; - reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&pcie1_pins>; - pinctrl-names = "default"; - max-link-speed = <1>; -}; - -&nand_controller { - status = "okay"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - #address-cells = <1>; - #size-cells = <0>; - - nand@0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - qcadata@0 { - label = "qcadata"; - reg = <0x0000000 0x0c80000>; - read-only; - }; - - APPSBL@c80000 { - label = "APPSBL"; - reg = <0x0c80000 0x0500000>; - read-only; - }; - - APPSBLENV@1180000 { - label = "APPSBLENV"; - reg = <0x1180000 0x0080000>; - read-only; - }; - - art: art@1200000 { - label = "art"; - reg = <0x1200000 0x0140000>; - read-only; - }; - - artbak: art@1340000 { - label = "artbak"; - reg = <0x1340000 0x0140000>; - read-only; - }; - - kernel@1480000 { - label = "kernel"; - reg = <0x1480000 0x0400000>; - }; - - ubi@1880000 { - label = "ubi"; - reg = <0x1880000 0x1C00000>; - }; - - netgear@3480000 { - label = "netgear"; - reg = <0x3480000 0x4480000>; - read-only; - }; - - reserve@7900000 { - label = "reserve"; - reg = <0x7900000 0x0700000>; - read-only; - }; - }; - }; -}; - -&mdio0 { - status = "okay"; - - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - }; -}; - -&gmac1 { - status = "okay"; - phy-mode = "rgmii"; - phy-handle = <&phy4>; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&art 6>; -}; - -&gmac2 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - - mtd-mac-address = <&art 0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&adm_dma { - status = "okay"; -}; diff --git a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-db149.dts b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-db149.dts deleted file mode 100644 index 8e8d942fbd..0000000000 --- a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-db149.dts +++ /dev/null @@ -1,163 +0,0 @@ -#include "qcom-ipq8064-v1.0.dtsi" - -/ { - model = "Qualcomm IPQ8064/DB149"; - compatible = "qcom,ipq8064-db149", "qcom,ipq8064"; - - aliases { - serial0 = &gsbi2_serial; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; -}; - -&qcom_pinmux { - rgmii0_pins: rgmii0_pins { - mux { - pins = "gpio2", "gpio66"; - drive-strength = <8>; - bias-disable; - }; - }; -}; - -&gsbi2 { - qcom,mode = ; - status = "okay"; - - gsbi2_serial: serial@12490000 { - status = "okay"; - }; -}; - -&gsbi4 { - status = "disabled"; -}; - -&gsbi4_serial { - status = "disabled"; -}; - -&flash { - m25p,fast-read; - - partition@0 { - label = "lowlevel_init"; - reg = <0x0 0x1b0000>; - }; - - partition@1 { - label = "u-boot"; - reg = <0x1b0000 0x80000>; - }; - - partition@2 { - label = "u-boot-env"; - reg = <0x230000 0x40000>; - }; - - partition@3 { - label = "caldata"; - reg = <0x270000 0x40000>; - }; - - partition@4 { - label = "firmware"; - reg = <0x2b0000 0x1d50000>; - }; -}; - -&usb3_0 { - status = "okay"; -}; - -&usb3_1 { - status = "okay"; -}; - -&pcie0 { - status = "okay"; -}; - -&pcie1 { - status = "okay"; -}; - -&pcie2 { - status = "okay"; -}; - -&mdio0 { - status = "okay"; - - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - }; - - phy6: ethernet-phy@6 { - reg = <6>; - }; - - phy7: ethernet-phy@7 { - reg = <7>; - }; -}; - -&gmac0 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <0>; - phy-handle = <&phy4>; - - pinctrl-0 = <&rgmii0_pins>; - pinctrl-names = "default"; -}; - -&gmac1 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <1>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gmac2 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - phy-handle = <&phy6>; -}; - -&gmac3 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <3>; - phy-handle = <&phy7>; -}; diff --git a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-ea7500-v1.dts b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-ea7500-v1.dts deleted file mode 100644 index 176807163e..0000000000 --- a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-ea7500-v1.dts +++ /dev/null @@ -1,87 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT - -#include "qcom-ipq8064-eax500.dtsi" - -/ { - model = "Linksys EA7500 V1 WiFi Router"; - compatible = "linksys,ea7500-v1", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0xe000000>; - device_type = "memory"; - }; - - aliases { - led-boot = &led_power; - led-failsafe = &led_power; - led-running = &led_power; - led-upgrade = &led_power; - }; - - chosen { - /* look for root deviceblock nbr in this bootarg */ - find-rootblock = "ubi.mtd="; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - led_power: power { - label = "white:power"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - }; -}; - -&qcom_pinmux { - button_pins: button_pins { - mux { - pins = "gpio65", "gpio68"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio6"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; -}; - -&partitions { - partition@5f80000 { - label = "sysdiag"; - reg = <0x5f80000 0x100000>; - }; - - partition@6080000 { - label = "syscfg"; - reg = <0x6080000 0x1f80000>; - }; -}; diff --git a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts deleted file mode 100644 index 9b01ae0328..0000000000 --- a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts +++ /dev/null @@ -1,122 +0,0 @@ -#include "qcom-ipq8064-eax500.dtsi" - -/ { - model = "Linksys EA8500 WiFi Router"; - compatible = "linksys,ea8500", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - aliases { - mdio-gpio0 = &mdio0; - - led-boot = &led_power; - led-failsafe = &led_power; - led-running = &led_power; - led-upgrade = &led_power; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - wps { - label = "green:wps"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - }; - - led_power: power { - label = "white:power"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - - wifi { - label = "green:wifi"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&qcom_pinmux { - button_pins: button_pins { - mux { - pins = "gpio65", "gpio67", "gpio68"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio6", "gpio53", "gpio54"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; -}; - -&sata_phy { - status = "okay"; -}; - -&sata { - status = "okay"; -}; - -&partitions { - partition@5f80000 { - label = "syscfg"; - reg = <0x5f80000 0x2080000>; - }; -}; - -&mdio0 { - phy4: ethernet-phy@4 { - reg = <4>; - }; -}; - -&gmac1 { - qcom,phy_mdio_addr = <4>; - qcom,poll_required = <1>; - qcom,rgmii_delay = <0>; - qcom,emulation = <0>; -}; - -/* LAN */ -&gmac2 { - qcom,phy_mdio_addr = <0>; /* none */ - qcom,poll_required = <0>; /* no polling */ - qcom,rgmii_delay = <0>; - qcom,emulation = <0>; -}; diff --git a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-eax500.dtsi b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-eax500.dtsi deleted file mode 100644 index 3e6732e9df..0000000000 --- a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-eax500.dtsi +++ /dev/null @@ -1,204 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT - -#include "qcom-ipq8064-v2.0.dtsi" - -#include - -/ { - chosen { - bootargs = "console=ttyMSM0,115200n8"; - /* append to bootargs adding the root deviceblock nbr from bootloader */ - append-rootblock = "ubi.mtd="; - }; -}; - -&usb3_0 { - status = "okay"; -}; - -&usb3_1 { - status = "okay"; -}; - -&pcie0 { - status = "okay"; - - max-link-speed = <1>; -}; - -&pcie1 { - status = "okay"; -}; - -&pcie2 { - status = "okay"; -}; - -&nand_controller { - status = "okay"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - nand@0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions: partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "SBL1"; - reg = <0x0000000 0x0040000>; - read-only; - }; - - partition@40000 { - label = "MIBIB"; - reg = <0x0040000 0x0140000>; - read-only; - }; - - partition@180000 { - label = "SBL2"; - reg = <0x0180000 0x0140000>; - read-only; - }; - - partition@2c0000 { - label = "SBL3"; - reg = <0x02c0000 0x0280000>; - read-only; - }; - - partition@540000 { - label = "DDRCONFIG"; - reg = <0x0540000 0x0120000>; - read-only; - }; - - partition@660000 { - label = "SSD"; - reg = <0x0660000 0x0120000>; - read-only; - }; - - partition@780000 { - label = "TZ"; - reg = <0x0780000 0x0280000>; - read-only; - }; - - partition@a00000 { - label = "RPM"; - reg = <0x0a00000 0x0280000>; - read-only; - }; - - art: partition@c80000 { - label = "art"; - reg = <0x0c80000 0x0140000>; - read-only; - }; - - partition@dc0000 { - label = "APPSBL"; - reg = <0x0dc0000 0x0100000>; - read-only; - }; - - partition@ec0000 { - label = "u_env"; - reg = <0x0ec0000 0x0040000>; - }; - - partition@f00000 { - label = "s_env"; - reg = <0x0f00000 0x0040000>; - }; - - partition@f40000 { - label = "devinfo"; - reg = <0x0f40000 0x0040000>; - }; - - partition@f80000 { - label = "kernel1"; - reg = <0x0f80000 0x2800000>; /* 3 MB spill to rootfs */ - }; - - partition@1280000 { - label = "rootfs1"; - reg = <0x1280000 0x2500000>; - }; - - partition@3780000 { - label = "kernel2"; - reg = <0x3780000 0x2800000>; - }; - - partition@3a80000 { - label = "rootfs2"; - reg = <0x3a80000 0x2500000>; - }; - }; - }; -}; - -&mdio0 { - status = "okay"; - - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x00010 0x2613a0 /* PWS_REG */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; -}; - -&gmac1 { - status = "okay"; - - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gmac2 { - status = "okay"; - - phy-mode = "sgmii"; - qcom,id = <2>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&adm_dma { - status = "okay"; -}; diff --git a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-r7500.dts b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-r7500.dts deleted file mode 100644 index ed8ab3dbfa..0000000000 --- a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-r7500.dts +++ /dev/null @@ -1,291 +0,0 @@ -#include "qcom-ipq8064-v1.0.dtsi" - -#include -#include - -/ { - model = "Netgear Nighthawk X4 R7500"; - compatible = "netgear,r7500", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0xe000000>; - device_type = "memory"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; - - aliases { - mdio-gpio0 = &mdio0; - - led-boot = &power_white; - led-failsafe = &power_amber; - led-running = &power_white; - led-upgrade = &power_amber; - }; - - chosen { - bootargs = "rootfstype=squashfs noinitrd"; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - usb1 { - label = "white:usb1"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - usb2 { - label = "white:usb2"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - power_amber: power_amber { - label = "amber:power"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - wan_white { - label = "white:wan"; - gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; - }; - - wan_amber { - label = "amber:wan"; - gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; - }; - - wps { - label = "white:wps"; - gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; - }; - - esata { - label = "white:esata"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; - }; - - power_white: power_white { - label = "white:power"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - wifi { - label = "white:wifi"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&qcom_pinmux { - button_pins: button_pins { - mux { - pins = "gpio6", "gpio54", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23", - "gpio24","gpio26", "gpio53", "gpio64"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; -}; - -&gsbi5 { - status = "disabled"; - - spi@1a280000 { - status = "disabled"; - }; -}; - -&usb3_0 { - clocks = <&gcc USB30_1_MASTER_CLK>; - status = "okay"; -}; - -&usb3_1 { - clocks = <&gcc USB30_0_MASTER_CLK>; - status = "okay"; -}; - -&pcie0 { - status = "okay"; -}; - -&pcie1 { - status = "okay"; - max-link-speed = <1>; -}; - -&nand_controller { - status = "okay"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - nand@0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - qcadata@0 { - label = "qcadata"; - reg = <0x0000000 0x0c80000>; - read-only; - }; - - APPSBL@c80000 { - label = "APPSBL"; - reg = <0x0c80000 0x0500000>; - read-only; - }; - - APPSBLENV@1180000 { - label = "APPSBLENV"; - reg = <0x1180000 0x0080000>; - read-only; - }; - - art: art@1200000 { - label = "art"; - reg = <0x1200000 0x0140000>; - read-only; - }; - - kernel@1340000 { - label = "kernel"; - reg = <0x1340000 0x0400000>; - }; - - ubi@1740000 { - label = "ubi"; - reg = <0x1740000 0x1600000>; - }; - - netgear@2d40000 { - label = "netgear"; - reg = <0x2d40000 0x0c00000>; - read-only; - }; - - reserve@3940000 { - label = "reserve"; - reg = <0x3940000 0x46c0000>; - read-only; - }; - }; - }; -}; - -&mdio0 { - status = "okay"; - - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - }; -}; - -&gmac1 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&art 6>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gmac2 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - - mtd-mac-address = <&art 0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&tcsr { - qcom,usb-ctrl-select = ; - compatible = "qcom,tcsr"; -}; - -&adm_dma { - status = "okay"; -}; diff --git a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts deleted file mode 100644 index 20a1fad7b2..0000000000 --- a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts +++ /dev/null @@ -1,312 +0,0 @@ -#include "qcom-ipq8064-v2.0.dtsi" - -#include - -/ { - model = "Netgear Nighthawk X4 R7500v2"; - compatible = "netgear,r7500v2", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - rsvd@5fe00000 { - reg = <0x5fe00000 0x200000>; - reusable; - }; - }; - - aliases { - mdio-gpio0 = &mdio0; - - led-boot = &power; - led-failsafe = &power; - led-running = &power; - led-upgrade = &power; - }; - - chosen { - bootargs = "rootfstype=squashfs noinitrd"; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - usb1 { - label = "amber:usb1"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - usb3 { - label = "amber:usb3"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - status { - label = "amber:status"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - internet { - label = "white:internet"; - gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; - }; - - wan { - label = "white:wan"; - gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; - }; - - wps { - label = "white:wps"; - gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; - }; - - esata { - label = "white:esata"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; - }; - - power: power { - label = "white:power"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - wifi { - label = "white:wifi"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&adm_dma { - status = "okay"; -}; - -&qcom_pinmux { - button_pins: button_pins { - mux { - pins = "gpio6", "gpio54", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23", - "gpio24","gpio26", "gpio53", "gpio64"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - usb0_pwr_en_pins: usb0_pwr_en_pins { - mux { - pins = "gpio15"; - function = "gpio"; - drive-strength = <12>; - bias-pull-down; - output-high; - }; - }; - - usb1_pwr_en_pins: usb1_pwr_en_pins { - mux { - pins = "gpio16", "gpio68"; - function = "gpio"; - drive-strength = <12>; - bias-pull-down; - output-high; - }; - }; -}; - -&sata_phy { - status = "okay"; -}; - -&sata { - status = "okay"; -}; - -&usb3_0 { - status = "okay"; - - pinctrl-0 = <&usb0_pwr_en_pins>; - pinctrl-names = "default"; -}; - -&usb3_1 { - status = "okay"; - - pinctrl-0 = <&usb1_pwr_en_pins>; - pinctrl-names = "default"; -}; - -&pcie0 { - status = "okay"; - reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>; - pinctrl-0 = <&pcie0_pins>; - pinctrl-names = "default"; -}; - -&pcie1 { - status = "okay"; - reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>; - pinctrl-0 = <&pcie1_pins>; - pinctrl-names = "default"; - max-link-speed = <1>; -}; - -&nand_controller { - status = "okay"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - nand@0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - qcadata@0 { - label = "qcadata"; - reg = <0x0000000 0x0c80000>; - read-only; - }; - - APPSBL@c80000 { - label = "APPSBL"; - reg = <0x0c80000 0x0500000>; - read-only; - }; - - APPSBLENV@1180000 { - label = "APPSBLENV"; - reg = <0x1180000 0x0080000>; - read-only; - }; - - art: art@1200000 { - label = "art"; - reg = <0x1200000 0x0140000>; - read-only; - }; - - artbak: art@1340000 { - label = "artbak"; - reg = <0x1340000 0x0140000>; - read-only; - }; - - kernel@1480000 { - label = "kernel"; - reg = <0x1480000 0x0400000>; - }; - - ubi@1880000 { - label = "ubi"; - reg = <0x1880000 0x6080000>; - }; - - reserve@7900000 { - label = "reserve"; - reg = <0x7900000 0x0700000>; - read-only; - }; - }; - }; -}; - -&mdio0 { - status = "okay"; - - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0xaa545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - }; -}; - -&gmac1 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&art 6>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gmac2 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - - mtd-mac-address = <&art 0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; \ No newline at end of file diff --git a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi deleted file mode 100644 index b9ee86a891..0000000000 --- a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi +++ /dev/null @@ -1,69 +0,0 @@ -#include "qcom-ipq8064.dtsi" - -/ { - aliases { - serial0 = &gsbi4_serial; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; -}; - -&gsbi4 { - qcom,mode = ; - status = "okay"; - - serial@16340000 { - status = "okay"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ -}; - -&CPU_SPC { - status = "okay"; -}; - -&pcie0 { - compatible = "qcom,pcie-ipq8064-v2"; -}; - -&pcie1 { - compatible = "qcom,pcie-ipq8064-v2"; -}; - -&pcie2 { - compatible = "qcom,pcie-ipq8064-v2"; -}; - -&sata { - ports-implemented = <0x1>; -}; - -&ss_phy_0 { - qcom,rx-eq = <2>; - qcom,tx-deamp_3_5db = <32>; - qcom,mpll = <5>; -}; - -&ss_phy_1 { - qcom,rx-eq = <2>; - qcom,tx-deamp_3_5db = <32>; - qcom,mpll = <5>; -}; diff --git a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts deleted file mode 100644 index ea7d0235ce..0000000000 --- a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts +++ /dev/null @@ -1,340 +0,0 @@ -#include "qcom-ipq8064-v2.0.dtsi" - -#include - -/ { - model = "TP-Link Archer VR2600v"; - compatible = "tplink,vr2600v", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - aliases { - mdio-gpio0 = &mdio0; - - led-boot = &power; - led-failsafe = &general; - led-running = &power; - led-upgrade = &general; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - dect { - label = "dect"; - gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - ledswitch { - label = "ledswitch"; - gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - dsl { - label = "white:dsl"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - usb { - label = "white:usb"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - lan { - label = "white:lan"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - wlan2g { - label = "white:wlan2g"; - gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>; - }; - - wlan5g { - label = "white:wlan5g"; - gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>; - }; - - power: power { - label = "white:power"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - phone { - label = "white:phone"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - }; - - wan { - label = "white:wan"; - gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>; - }; - - general: general { - label = "white:general"; - gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&qcom_pinmux { - led_pins: led_pins { - mux { - pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio17", - "gpio26", "gpio53", "gpio56", "gpio66"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - button_pins: button_pins { - mux { - pins = "gpio54", "gpio64", "gpio65", "gpio67", "gpio68"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - bias-pull-down; - }; - - data { - pins = "gpio18", "gpio19"; - drive-strength = <10>; - }; - - cs { - pins = "gpio20"; - drive-strength = <10>; - bias-pull-up; - }; - - clk { - pins = "gpio21"; - drive-strength = <12>; - }; - }; -}; - -&gsbi5 { - qcom,mode = ; - status = "okay"; - - spi4: spi@1a280000 { - status = "okay"; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; - - W25Q128@0 { - compatible = "jedec,spi-nor"; - #address-cells = <1>; - #size-cells = <1>; - spi-max-frequency = <50000000>; - reg = <0>; - - SBL1@0 { - label = "SBL1"; - reg = <0x0 0x20000>; - read-only; - }; - - MIBIB@20000 { - label = "MIBIB"; - reg = <0x20000 0x20000>; - read-only; - }; - - SBL2@40000 { - label = "SBL2"; - reg = <0x40000 0x40000>; - read-only; - }; - - SBL3@80000 { - label = "SBL3"; - reg = <0x80000 0x80000>; - read-only; - }; - - DDRCONFIG@100000 { - label = "DDRCONFIG"; - reg = <0x100000 0x10000>; - read-only; - }; - - SSD@110000 { - label = "SSD"; - reg = <0x110000 0x10000>; - read-only; - }; - - TZ@120000 { - label = "TZ"; - reg = <0x120000 0x80000>; - read-only; - }; - - RPM@1a0000 { - label = "RPM"; - reg = <0x1a0000 0x80000>; - read-only; - }; - - APPSBL@220000 { - label = "APPSBL"; - reg = <0x220000 0x80000>; - read-only; - }; - - APPSBLENV@2a0000 { - label = "APPSBLENV"; - reg = <0x2a0000 0x40000>; - read-only; - }; - - OLDART@2e0000 { - label = "OLDART"; - reg = <0x2e0000 0x40000>; - read-only; - }; - - kernel@320000 { - label = "kernel"; - reg = <0x320000 0x300000>; - }; - - rootfs@620000 { - label = "rootfs"; - reg = <0x620000 0x960000>; - }; - - defaultmac: default-mac@0xfaf100 { - label = "default-mac"; - reg = <0xfaf100 0x00200>; - read-only; - }; - - ART@fc0000 { - label = "ART"; - reg = <0xfc0000 0x40000>; - read-only; - }; - }; - }; -}; - -&usb3_0 { - status = "okay"; -}; - -&usb3_1 { - status = "okay"; -}; - -&pcie0 { - status = "okay"; -}; - -&pcie1 { - status = "okay"; - max-link-speed = <1>; -}; - -&mdio0 { - status = "okay"; - - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - }; -}; - -&gmac1 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&defaultmac 0>; - mtd-mac-address-increment = <1>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gmac2 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - - mtd-mac-address = <&defaultmac 0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&adm_dma { - status = "okay"; -}; diff --git a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts deleted file mode 100644 index 1a6b7eb4d6..0000000000 --- a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts +++ /dev/null @@ -1,370 +0,0 @@ -#include "qcom-ipq8064-v2.0.dtsi" - -#include - -/ { - model = "NEC Aterm WG2600HP"; - compatible = "nec,wg2600hp", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - aliases { - mdio-gpio0 = &mdio0; - - led-boot = &power_green; - led-failsafe = &power_red; - led-running = &power_green; - led-upgrade = &power_green; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - bridge { - label = "bridge"; - gpios = <&qcom_pinmux 24 GPIO_ACTIVE_LOW>; - linux,code = ; - linux,input-type = ; - }; - - converter { - label = "converter"; - gpios = <&qcom_pinmux 25 GPIO_ACTIVE_LOW>; - linux,code = ; - linux,input-type = ; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - converter_green { - label = "green:converter"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_HIGH>; - }; - - power_red: power_red { - label = "red:power"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - active_green { - label = "green:active"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - active_red { - label = "red:active"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - power_green: power_green { - label = "green:power"; - gpios = <&qcom_pinmux 14 GPIO_ACTIVE_HIGH>; - }; - - converter_red { - label = "red:converter"; - gpios = <&qcom_pinmux 15 GPIO_ACTIVE_HIGH>; - }; - - wlan2g_green { - label = "green:wlan2g"; - gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>; - }; - - wlan2g_red { - label = "red:wlan2g"; - gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>; - }; - - wlan5g_green { - label = "green:wlan5g"; - gpios = <&qcom_pinmux 57 GPIO_ACTIVE_HIGH>; - }; - - wlan5g_red { - label = "red:wlan5g"; - gpios = <&qcom_pinmux 58 GPIO_ACTIVE_HIGH>; - }; - - tv_green { - label = "green:tv"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; - }; - - tv_red { - label = "red:tv"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&adm_dma { - status = "okay"; -}; - -&mdio0 { - status = "okay"; - - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x06000000 /* PAD0_MODE */ - 0x0000c 0x00080080 /* PAD6_MODE */ - 0x000e4 0x0006a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x0000004e /* PORT0_STATUS */ - 0x00094 0x0000004e /* PORT6_STATUS */ - >; - }; - - ethernet-phy@4 { - reg = <4>; - }; -}; - -&gmac1 { - status = "okay"; - - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&PRODUCTDATA 6>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gmac2 { - status = "okay"; - - phy-mode = "sgmii"; - qcom,id = <2>; - - mtd-mac-address = <&PRODUCTDATA 0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gsbi5 { - status = "okay"; - - qcom,mode = ; - - spi@1a280000 { - status = "okay"; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; - - flash@0 { - compatible = "jedec,spi-nor"; - spi-max-frequency = <50000000>; - reg = <0>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - SBL1@0 { - label = "SBL1"; - reg = <0x0 0x20000>; - read-only; - }; - - MIBIB@20000 { - label = "MIBIB"; - reg = <0x20000 0x20000>; - read-only; - }; - - SBL2@40000 { - label = "SBL2"; - reg = <0x40000 0x40000>; - read-only; - }; - - SBL3@80000 { - label = "SBL3"; - reg = <0x80000 0x80000>; - read-only; - }; - - DDRCONFIG@100000 { - label = "DDRCONFIG"; - reg = <0x100000 0x10000>; - read-only; - }; - - SSD@110000 { - label = "SSD"; - reg = <0x110000 0x10000>; - read-only; - }; - - TZ@120000 { - label = "TZ"; - reg = <0x120000 0x80000>; - read-only; - }; - - RPM@1a0000 { - label = "RPM"; - reg = <0x1a0000 0x80000>; - read-only; - }; - - APPSBL@220000 { - label = "APPSBL"; - reg = <0x220000 0x80000>; - read-only; - }; - - APPSBLENV@2a0000 { - label = "APPSBLENV"; - reg = <0x2a0000 0x10000>; - }; - - PRODUCTDATA: PRODUCTDATA@2b0000 { - label = "PRODUCTDATA"; - reg = <0x2b0000 0x30000>; - read-only; - }; - - ART@2e0000 { - label = "ART"; - reg = <0x2e0000 0x40000>; - read-only; - }; - - TP@320000 { - label = "TP"; - reg = <0x320000 0x40000>; - read-only; - }; - - TINY@360000 { - label = "TINY"; - reg = <0x360000 0x500000>; - read-only; - }; - - firmware@860000 { - compatible = "denx,uimage"; - label = "firmware"; - reg = <0x860000 0x17a0000>; - }; - }; - }; - }; -}; - -&usb3_0 { - status = "okay"; - - pinctrl-0 = <&usb_pwr_en_pins>; - pinctrl-names = "default"; -}; - -&usb3_1 { - status = "okay"; -}; - -&pcie0 { - status = "okay"; -}; - -&pcie1 { - status = "okay"; - max-link-speed = <1>; -}; - -&qcom_pinmux { - button_pins: button_pins { - mux { - pins = "gpio16", "gpio54", "gpio24", "gpio25"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio14", - "gpio15", "gpio55", "gpio56", "gpio57", "gpio58", - "gpio64", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-down; - }; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - bias-pull-down; - }; - - data { - pins = "gpio18", "gpio19"; - drive-strength = <10>; - }; - - cs { - pins = "gpio20"; - drive-strength = <10>; - bias-pull-up; - }; - - clk { - pins = "gpio21"; - drive-strength = <12>; - }; - }; - - usb_pwr_en_pins: usb_pwr_en_pins { - mux { - pins = "gpio22"; - function = "gpio"; - drive-strength = <2>; - bias-pull-down; - output-high; - }; - }; -}; diff --git a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-wpq864.dts b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-wpq864.dts deleted file mode 100644 index 739b7261a3..0000000000 --- a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-wpq864.dts +++ /dev/null @@ -1,486 +0,0 @@ -/* - * BSD LICENSE - * - * Copyright (C) 2017 Christian Mehlis - * Copyright (C) 2018 Mathias Kresin - * All rights reserved. - * - * Redistribution and use in source and binary forms, with or without - * modification, are permitted provided that the following conditions - * are met: - * - * 1. Redistributions of source code must retain the above copyright - * notice, this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright - * notice, this list of conditions and the following disclaimer in the - * documentation and/or other materials provided with the distribution. - * 3. Neither the names of the copyright holders nor the names of any - * contributors may be used to endorse or promote products derived - * from this software without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS - * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT - * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR - * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT - * HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, - * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT - * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, - * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY - * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - */ - -#include "qcom-ipq8064-v1.0.dtsi" - -#include -#include - -/ { - compatible = "compex,wpq864", "qcom,ipq8064"; - model = "Compex WPQ864"; - - aliases { - mdio-gpio0 = &mdio0; - ethernet0 = &gmac1; - ethernet1 = &gmac0; - - led-boot = &led_pass; - led-failsafe = &led_fail; - led-running = &led_pass; - led-upgrade = &led_pass; - }; - - leds { - compatible = "gpio-leds"; - - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - rss4 { - label = "green:rss4"; - gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; - }; - - rss3 { - label = "green:rss3"; - gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - rss2 { - label = "orange:rss2"; - gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>; - }; - - rss1 { - label = "red:rss1"; - gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; - }; - - led_pass: pass { - label = "green:pass"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - }; - - led_fail: fail { - label = "green:fail"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - usb { - label = "green:usb"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - usb-pcie { - label = "green:usb-pcie"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - }; - - keys { - compatible = "gpio-keys"; - - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - beeper { - compatible = "gpio-beeper"; - - pinctrl-0 = <&beeper_pins>; - pinctrl-names = "default"; - - gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>; - }; -}; - -&rpm { - pinctrl-0 = <&rpm_pins>; - pinctrl-names = "default"; -}; - -&nand_controller { - status = "okay"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - mt29f2g08abbeah4@0 { - compatible = "qcom,nandcs"; - - reg = <0>; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - SBL1@0 { - label = "SBL1"; - reg = <0x0000000 0x0040000>; - read-only; - }; - - MIBIB@40000 { - label = "MIBIB"; - reg = <0x0040000 0x0140000>; - read-only; - }; - - SBL2@180000 { - label = "SBL2"; - reg = <0x0180000 0x0140000>; - read-only; - }; - - SBL3@2c0000 { - label = "SBL3"; - reg = <0x02c0000 0x0280000>; - read-only; - }; - - DDRCONFIG@540000 { - label = "DDRCONFIG"; - reg = <0x0540000 0x0120000>; - read-only; - }; - - SSD@660000 { - label = "SSD"; - reg = <0x0660000 0x0120000>; - read-only; - }; - - TZ@780000 { - label = "TZ"; - reg = <0x0780000 0x0280000>; - read-only; - }; - - RPM@a00000 { - label = "RPM"; - reg = <0x0a00000 0x0280000>; - read-only; - }; - - APPSBL@c80000 { - label = "APPSBL"; - reg = <0x0c80000 0x0500000>; - read-only; - }; - - APPSBLENV@1180000 { - label = "APPSBLENV"; - reg = <0x1180000 0x0080000>; - }; - - ART@1200000 { - label = "ART"; - reg = <0x1200000 0x0140000>; - }; - - ubi@1340000 { - label = "ubi"; - reg = <0x1340000 0x4000000>; - }; - - BOOTCONFIG@5340000 { - label = "BOOTCONFIG"; - reg = <0x5340000 0x0060000>; - }; - - SBL2-1@53a0000- { - label = "SBL2_1"; - reg = <0x53a0000 0x0140000>; - read-only; - }; - - SBL3-1@54e0000 { - label = "SBL3_1"; - reg = <0x54e0000 0x0280000>; - read-only; - }; - - DDRCONFIG-1@5760000 { - label = "DDRCONFIG_1"; - reg = <0x5760000 0x0120000>; - read-only; - }; - - SSD-1@5880000 { - label = "SSD_1"; - reg = <0x5880000 0x0120000>; - read-only; - }; - - TZ-1@59a0000 { - label = "TZ_1"; - reg = <0x59a0000 0x0280000>; - read-only; - }; - - RPM-1@5c20000 { - label = "RPM_1"; - reg = <0x5c20000 0x0280000>; - read-only; - }; - - BOOTCONFIG1@5ea0000 { - label = "BOOTCONFIG1"; - reg = <0x5ea0000 0x0060000>; - }; - - APPSBL-1@5f00000 { - label = "APPSBL_1"; - reg = <0x5f00000 0x0500000>; - read-only; - }; - - ubi-1@6400000 { - label = "ubi_1"; - reg = <0x6400000 0x4000000>; - }; - - unused@a400000 { - label = "unused"; - reg = <0xa400000 0x5c00000>; - }; - }; - }; -}; - -&adm_dma { - status = "okay"; -}; - -&mdio0 { - status = "okay"; - - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - >; - }; - - ethernet-phy@4 { - reg = <4>; - }; -}; - -&gmac1 { - status = "okay"; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - phy-mode = "rgmii"; - qcom,id = <1>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gmac2 { - status = "okay"; - - phy-mode = "sgmii"; - qcom,id = <2>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gsbi4_serial { - pinctrl-0 = <&uart0_pins>; - pinctrl-names = "default"; -}; - -&flash { - compatible = "jedec,spi-nor"; -}; - -&sata_phy { - status = "disabled"; -}; - -&sata { - status = "disabled"; -}; - -&ss_phy_0 { /* USB3 port 0 SS phy */ - status = "okay"; - - rx_eq = <2>; - tx_deamp_3_5db = <32>; - mpll = <160>; -}; - -&ss_phy_1 { /* USB3 port 1 SS phy */ - status = "okay"; - - rx_eq = <2>; - tx_deamp_3_5db = <32>; - mpll = <160>; -}; - -&pcie0 { - status = "okay"; - - /delete-property/ pinctrl-0; - /delete-property/ pinctrl-names; - /delete-property/ perst-gpios; -}; - -&pcie1 { - status = "okay"; -}; - -&pcie2 { - status = "okay"; - - /delete-property/ pinctrl-0; - /delete-property/ pinctrl-names; - /delete-property/ perst-gpios; -}; - -&qcom_pinmux { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinctrl0 { - pcie0_pcie2_perst { - pins = "gpio3"; - function = "gpio"; - drive-strength = <2>; - bias-disable; - output-high; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio7", "gpio8", "gpio9", "gpio22", - "gpio23", "gpio24", "gpio25", "gpio53"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - button_pins: button_pins { - mux { - pins = "gpio54"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - beeper_pins: beeper_pins { - mux { - pins = "gpio55"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - rpm_pins: rpm_pins { - mux { - pins = "gpio12", "gpio13"; - function = "gsbi4"; - drive-strength = <10>; - bias-disable; - }; - }; - - uart0_pins: uart0_pins { - mux { - pins = "gpio10", "gpio11"; - function = "gsbi4"; - drive-strength = <10>; - bias-disable; - }; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19"; - function = "gsbi5"; - drive-strength = <10>; - bias-pull-down; - }; - - clk { - pins = "gpio21"; - function = "gsbi5"; - drive-strength = <12>; - bias-pull-down; - }; - - cs { - pins = "gpio20"; - function = "gpio"; - drive-strength = <10>; - bias-pull-up; - }; - }; -}; - -&usb3_0 { - status = "okay"; -}; - -&usb3_1 { - status = "okay"; -}; - -&tcsr { - qcom,usb-ctrl-select = ; -}; diff --git a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts deleted file mode 100644 index d80bfa204d..0000000000 --- a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts +++ /dev/null @@ -1,450 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT -#include "qcom-ipq8064-v2.0.dtsi" - -#include - -/ { - model = "Buffalo WXR-2533DHP"; - compatible = "buffalo,wxr-2533dhp", "qcom,ipq8064"; - - memory@42000000 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - aliases { - led-boot = &power; - led-failsafe = &diag; - led-running = &power; - led-upgrade = &power; - }; - - chosen { - /* use "ubi_rootfs" volume in "ubi" partition as rootfs */ - bootargs = "ubi.block=0,1 root=/dev/ubiblock0_1 rootfstype=squashfs"; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - usb { - label = "green:usb"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "usbport"; - trigger-sources = <&hub_port0 &hub_port1>; - }; - - guestport { - label = "green:guestport"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - diag: diag { - label = "orange:diag"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - internet_orange { - label = "orange:internet"; - gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>; - }; - - internet_white { - label = "white:internet"; - gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; - }; - - wireless_orange { - label = "orange:wireless"; - gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; - }; - - wireless_white { - label = "white:wireless"; - gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; - }; - - router_orange { - label = "orange:router"; - gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>; - }; - - router_white { - label = "white:router"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>; - }; - - power: power { - label = "white:power"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - }; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - power { - label = "power"; - gpios = <&qcom_pinmux 58 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - eject { - label = "eject"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - guest { - label = "guest"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - ap { - label = "ap"; - gpios = <&qcom_pinmux 55 GPIO_ACTIVE_LOW>; - linux,code = ; - linux,input-type = ; - }; - - router { - label = "router"; - gpios = <&qcom_pinmux 56 GPIO_ACTIVE_LOW>; - linux,code = ; - linux,input-type = ; - }; - - auto { - label = "auto"; - gpios = <&qcom_pinmux 57 GPIO_ACTIVE_LOW>; - linux,code = ; - linux,input-type = ; - }; - }; -}; - -&nand_controller { - status = "okay"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - cs@0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - ubi@0 { - label = "ubi"; - reg = <0x0000000 0x4000000>; - }; - - rootfs_1@4000000 { - label = "rootfs_1"; - reg = <0x4000000 0x4000000>; - }; - }; - }; -}; - -&adm_dma { - status = "okay"; -}; - -&mdio0 { - status = "okay"; - - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x07600000 /* PAD0_MODE */ - 0x00008 0x01000000 /* PAD5_MODE */ - 0x0000c 0x00000080 /* PAD6_MODE */ - 0x00050 0xcc35cc35 /* LED_CTRL0 */ - 0x00054 0xca35ca35 /* LED_CTRL1 */ - 0x00058 0xc935c935 /* LED_CTRL2 */ - 0x0005c 0x03ffff00 /* LED_CTRL3 */ - 0x000e4 0x0006a545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x0000007e /* PORT0_STATUS */ - 0x00094 0x0000007e /* PORT6_STATUS */ - >; - }; - - ethernet-phy@4 { - reg = <4>; - }; -}; - -&gmac1 { - status = "okay"; - - phy-mode = "rgmii"; - qcom,id = <1>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&ART 6>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gmac2 { - status = "okay"; - - phy-mode = "sgmii"; - qcom,id = <2>; - - mtd-mac-address = <&ART 0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gsbi4_serial { - pinctrl-0 = <&uart0_pins>; - pinctrl-names = "default"; -}; - -&gsbi5 { - status = "okay"; - qcom,mode = ; - - spi@1a280000 { - status = "okay"; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; - - flash@0 { - compatible = "jedec,spi-nor"; - spi-max-frequency = <50000000>; - reg = <0>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - SBL1@0 { - label = "SBL1"; - reg = <0x0 0x10000>; - read-only; - }; - - MIBIB@10000 { - label = "MIBIB"; - reg = <0x10000 0x20000>; - read-only; - }; - - SBL2@30000 { - label = "SBL2"; - reg = <0x30000 0x30000>; - read-only; - }; - - SBL3@60000 { - label = "SBL3"; - reg = <0x60000 0x30000>; - read-only; - }; - - DDRCONFIG@90000 { - label = "DDRCONFIG"; - reg = <0x90000 0x10000>; - read-only; - }; - - SSD@a0000 { - label = "SSD"; - reg = <0xa0000 0x10000>; - read-only; - }; - - TZ@b0000 { - label = "TZ"; - reg = <0xb0000 0x30000>; - read-only; - }; - - RPM@e0000 { - label = "RPM"; - reg = <0xe0000 0x20000>; - read-only; - }; - - APPSBL@100000 { - label = "APPSBL"; - reg = <0x100000 0x70000>; - read-only; - }; - - APPSBLENV@170000 { - label = "APPSBLENV"; - reg = <0x170000 0x10000>; - read-only; - }; - - ART: ART@180000 { - label = "ART"; - reg = <0x180000 0x40000>; - read-only; - }; - - BOOTCONFIG@1c0000 { - label = "BOOTCONFIG"; - reg = <0x1c0000 0x10000>; - read-only; - }; - - APPSBL_1@1d0000 { - label = "APPSBL_1"; - reg = <0x1d0000 0x70000>; - read-only; - }; - }; - }; - }; -}; - -&usb3_0 { - status = "okay"; - - pinctrl-0 = <&usb_pwr_en_pins>; - pinctrl-names = "default"; -}; - -&usb3_1 { - status = "okay"; -}; - -&dwc3_0 { - #address-cells = <1>; - #size-cells = <0>; - - hub_port0: port@1 { - reg = <1>; - #trigger-source-cells = <0>; - }; -}; - -&dwc3_1 { - #address-cells = <1>; - #size-cells = <0>; - - hub_port1: port@1 { - reg = <1>; - #trigger-source-cells = <0>; - }; -}; - -&pcie0 { - status = "okay"; -}; - -&pcie1 { - status = "okay"; - max-link-speed = <1>; -}; - -&qcom_pinmux { - button_pins: button_pins { - mux { - pins = "gpio6", "gpio54", "gpio55", "gpio56", "gpio57", - "gpio58", "gpio64", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio22", - "gpio23", "gpio24", "gpio25", "gpio26", "gpio53"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - uart0_pins: uart0_pins { - mux { - pins = "gpio10", "gpio11"; - function = "gsbi4"; - drive-strength = <12>; - bias-disable; - }; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - bias-pull-down; - }; - - data { - pins = "gpio18", "gpio19"; - drive-strength = <10>; - }; - - cs{ - pins = "gpio20"; - drive-strength = <10>; - bias-pull-up; - }; - - clk { - pins = "gpio21"; - drive-strength = <12>; - }; - }; - - usb_pwr_en_pins: usb_pwr_en_pins { - mux{ - pins = "gpio68"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - output-high; - }; - }; -}; \ No newline at end of file diff --git a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts deleted file mode 100644 index 2573349f55..0000000000 --- a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts +++ /dev/null @@ -1,310 +0,0 @@ -#include "qcom-ipq8065.dtsi" - -#include - -/ { - model = "ZyXEL NBG6817"; - compatible = "zyxel,nbg6817", "qcom,ipq8065", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - aliases { - mdio-gpio0 = &mdio0; - sdcc1 = &sdcc1; - - led-boot = &power; - led-failsafe = &power; - led-running = &power; - led-upgrade = &power; - }; - - chosen { - bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd"; - append-rootblock = "root=/dev/mmcblk0p"; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_LOW>; - linux,code = ; - linux,input-type = ; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - internet { - label = "white:internet"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; - }; - - power: power { - label = "white:power"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - wifi2g { - label = "amber:wifi2g"; - gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>; - }; - - /* wifi2g amber from the manual is missing */ - - wifi5g { - label = "amber:wifi5g"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; - }; - - /* wifi5g amber from the manual is missing */ - }; -}; - -&qcom_pinmux { - button_pins: button_pins { - mux { - pins = "gpio53", "gpio54", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio9", "gpio26", "gpio33", "gpio64"; - function = "gpio"; - drive-strength = <2>; - bias-pull-down; - }; - }; - - mdio0_pins: mdio0_pins { - clk { - pins = "gpio1"; - input-disable; - }; - }; - - rgmii2_pins: rgmii2_pins { - tx { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ; - input-disable; - }; - }; - - spi_pins: spi_pins { - cs { - pins = "gpio20"; - drive-strength = <12>; - }; - }; - - usb0_pwr_en_pins: usb0_pwr_en_pins { - mux { - pins = "gpio16", "gpio17"; - function = "gpio"; - drive-strength = <12>; - }; - - pwr { - pins = "gpio17"; - bias-pull-down; - output-high; - }; - - ovc { - pins = "gpio16"; - bias-pull-up; - }; - }; - - usb1_pwr_en_pins: usb1_pwr_en_pins { - mux { - pins = "gpio14", "gpio15"; - function = "gpio"; - drive-strength = <12>; - }; - - pwr { - pins = "gpio14"; - bias-pull-down; - output-high; - }; - - ovc { - pins = "gpio15"; - bias-pull-up; - }; - }; -}; - -&gsbi5 { - qcom,mode = ; - status = "okay"; - - spi4: spi@1a280000 { - status = "okay"; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; - - m25p80@0 { - compatible = "jedec,spi-nor"; - #address-cells = <1>; - #size-cells = <1>; - spi-max-frequency = <51200000>; - reg = <0>; - - partitions { - compatible = "qcom,smem"; - }; - }; - }; -}; - -&usb3_0 { - status = "okay"; - - pinctrl-0 = <&usb0_pwr_en_pins>; - pinctrl-names = "default"; -}; - -&usb3_1 { - status = "okay"; - - pinctrl-0 = <&usb1_pwr_en_pins>; - pinctrl-names = "default"; -}; - -&pcie0 { - status = "okay"; - reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>; - pinctrl-0 = <&pcie0_pins>; - pinctrl-names = "default"; -}; - -&pcie1 { - status = "okay"; - reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>; - pinctrl-0 = <&pcie1_pins>; - pinctrl-names = "default"; - max-link-speed = <1>; -}; - -&mdio0 { - status = "okay"; - - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0xaa545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - 0x00970 0x1e864443 /* QM_PORT0_CTRL0 */ - 0x00974 0x000001c6 /* QM_PORT0_CTRL1 */ - 0x00978 0x19008643 /* QM_PORT1_CTRL0 */ - 0x0097c 0x000001c6 /* QM_PORT1_CTRL1 */ - 0x00980 0x19008643 /* QM_PORT2_CTRL0 */ - 0x00984 0x000001c6 /* QM_PORT2_CTRL1 */ - 0x00988 0x19008643 /* QM_PORT3_CTRL0 */ - 0x0098c 0x000001c6 /* QM_PORT3_CTRL1 */ - 0x00990 0x19008643 /* QM_PORT4_CTRL0 */ - 0x00994 0x000001c6 /* QM_PORT4_CTRL1 */ - 0x00998 0x1e864443 /* QM_PORT5_CTRL0 */ - 0x0099c 0x000001c6 /* QM_PORT5_CTRL1 */ - 0x009a0 0x1e864443 /* QM_PORT6_CTRL0 */ - 0x009a4 0x000001c6 /* QM_PORT6_CTRL1 */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - qca,ar8327-initvals = < - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x0000c 0x80 /* PAD6_MODE */ - >; - }; -}; - -&gmac1 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <1>; - qcom,phy_mdio_addr = <4>; - qcom,poll_required = <0>; - qcom,rgmii_delay = <1>; - qcom,phy_mii_type = <0>; - qcom,emulation = <0>; - qcom,irq = <255>; - mdiobus = <&mdio0>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gmac2 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - qcom,phy_mdio_addr = <0>; /* none */ - qcom,poll_required = <0>; /* no polling */ - qcom,rgmii_delay = <0>; - qcom,phy_mii_type = <1>; - qcom,emulation = <0>; - qcom,irq = <258>; - mdiobus = <&mdio0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&amba { - sdcc1: sdcc@12400000 { - status = "okay"; - }; -}; - -&adm_dma { - status = "okay"; -}; diff --git a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8065-r7800.dts b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8065-r7800.dts deleted file mode 100644 index 181f6d3bde..0000000000 --- a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8065-r7800.dts +++ /dev/null @@ -1,449 +0,0 @@ -#include "qcom-ipq8065.dtsi" - -#include - -/ { - model = "Netgear Nighthawk X4S R7800"; - compatible = "netgear,r7800", "qcom,ipq8065", "qcom,ipq8064"; - - memory@0 { - reg = <0x42000000 0x1e000000>; - device_type = "memory"; - }; - - reserved-memory { - rsvd@5fe00000 { - reg = <0x5fe00000 0x200000>; - reusable; - }; - }; - - aliases { - mdio-gpio0 = &mdio0; - - led-boot = &power_white; - led-failsafe = &power_amber; - led-running = &power_white; - led-upgrade = &power_amber; - label-mac-device = &gmac2; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - wifi { - label = "wifi"; - gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; - linux,code = ; - debounce-interval = <60>; - wakeup-source; - }; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; - linux,code = ; - debounce-interval = <60>; - wakeup-source; - }; - - wps { - label = "wps"; - gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; - linux,code = ; - debounce-interval = <60>; - wakeup-source; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - power_white: power_white { - label = "white:power"; - gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - power_amber: power_amber { - label = "amber:power"; - gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; - }; - - wan_white { - label = "white:wan"; - gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; - }; - - wan_amber { - label = "amber:wan"; - gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; - }; - - usb1 { - label = "white:usb1"; - gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; - }; - - usb2 { - label = "white:usb2"; - gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; - }; - - esata { - label = "white:esata"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; - }; - - wifi { - label = "white:wifi"; - gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; - }; - - wps { - label = "white:wps"; - gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&qcom_pinmux { - button_pins: button_pins { - mux { - pins = "gpio6", "gpio54", "gpio65"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23", - "gpio24","gpio26", "gpio53", "gpio64"; - function = "gpio"; - drive-strength = <2>; - bias-pull-down; - }; - }; - - mdio0_pins: mdio0_pins { - clk { - pins = "gpio1"; - input-disable; - }; - }; - - rgmii2_pins: rgmii2_pins { - tx { - pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ; - input-disable; - }; - }; - - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19", "gpio21"; - function = "gsbi5"; - bias-pull-down; - }; - - data { - pins = "gpio18", "gpio19"; - drive-strength = <10>; - }; - - cs { - pins = "gpio20"; - drive-strength = <10>; - bias-pull-up; - }; - - clk { - pins = "gpio21"; - drive-strength = <12>; - }; - }; - - spi6_pins: spi6_pins { - mux { - pins = "gpio55", "gpio56", "gpio58"; - function = "gsbi6"; - bias-pull-down; - }; - - mosi { - pins = "gpio55"; - drive-strength = <12>; - }; - - miso { - pins = "gpio56"; - drive-strength = <14>; - }; - - cs { - pins = "gpio57"; - drive-strength = <12>; - bias-pull-up; - }; - - clk { - pins = "gpio58"; - drive-strength = <12>; - }; - - reset { - pins = "gpio33"; - drive-strength = <10>; - bias-pull-down; - output-high; - }; - }; - - usb0_pwr_en_pins: usb0_pwr_en_pins { - mux { - pins = "gpio15"; - function = "gpio"; - drive-strength = <12>; - bias-pull-down; - output-high; - }; - }; - - usb1_pwr_en_pins: usb1_pwr_en_pins { - mux { - pins = "gpio16", "gpio68"; - function = "gpio"; - drive-strength = <12>; - bias-pull-down; - output-high; - }; - }; -}; - -&nand_controller { - status = "okay"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - nand@0 { - reg = <0>; - compatible = "qcom,nandcs"; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - qcadata@0 { - label = "qcadata"; - reg = <0x0000000 0x0c80000>; - read-only; - }; - - APPSBL@c80000 { - label = "APPSBL"; - reg = <0x0c80000 0x0500000>; - read-only; - }; - - APPSBLENV@1180000 { - label = "APPSBLENV"; - reg = <0x1180000 0x0080000>; - read-only; - }; - - art: art@1200000 { - label = "art"; - reg = <0x1200000 0x0140000>; - read-only; - }; - - artbak: art@1340000 { - label = "artbak"; - reg = <0x1340000 0x0140000>; - read-only; - }; - - kernel@1480000 { - label = "kernel"; - reg = <0x1480000 0x0400000>; - }; - - ubi@1880000 { - label = "ubi"; - reg = <0x1880000 0x6080000>; - }; - - reserve@7900000 { - label = "reserve"; - reg = <0x7900000 0x0700000>; - read-only; - }; - }; - }; -}; - -&mdio0 { - status = "okay"; - - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,ar8327-initvals = < - 0x00004 0x7600000 /* PAD0_MODE */ - 0x00008 0x1000000 /* PAD5_MODE */ - 0x0000c 0x80 /* PAD6_MODE */ - 0x000e4 0xaa545 /* MAC_POWER_SEL */ - 0x000e0 0xc74164de /* SGMII_CTRL */ - 0x0007c 0x4e /* PORT0_STATUS */ - 0x00094 0x4e /* PORT6_STATUS */ - 0x00970 0x1e864443 /* QM_PORT0_CTRL0 */ - 0x00974 0x000001c6 /* QM_PORT0_CTRL1 */ - 0x00978 0x19008643 /* QM_PORT1_CTRL0 */ - 0x0097c 0x000001c6 /* QM_PORT1_CTRL1 */ - 0x00980 0x19008643 /* QM_PORT2_CTRL0 */ - 0x00984 0x000001c6 /* QM_PORT2_CTRL1 */ - 0x00988 0x19008643 /* QM_PORT3_CTRL0 */ - 0x0098c 0x000001c6 /* QM_PORT3_CTRL1 */ - 0x00990 0x19008643 /* QM_PORT4_CTRL0 */ - 0x00994 0x000001c6 /* QM_PORT4_CTRL1 */ - 0x00998 0x1e864443 /* QM_PORT5_CTRL0 */ - 0x0099c 0x000001c6 /* QM_PORT5_CTRL1 */ - 0x009a0 0x1e864443 /* QM_PORT6_CTRL0 */ - 0x009a4 0x000001c6 /* QM_PORT6_CTRL1 */ - >; - qca,ar8327-vlans = < - 0x1 0x5e /* VLAN1 Ports 1/2/3/4/6 */ - 0x2 0x21 /* VLAN2 Ports 0/5 */ - >; - }; - - phy4: ethernet-phy@4 { - reg = <4>; - qca,ar8327-initvals = < - 0x000e4 0x6a545 /* MAC_POWER_SEL */ - 0x0000c 0x80 /* PAD6_MODE */ - >; - }; -}; - -&gmac1 { - status = "okay"; - phy-mode = "rgmii"; - qcom,id = <1>; - qcom,phy_mdio_addr = <4>; - qcom,poll_required = <0>; - qcom,rgmii_delay = <1>; - qcom,phy_mii_type = <0>; - qcom,emulation = <0>; - qcom,irq = <255>; - mdiobus = <&mdio0>; - - pinctrl-0 = <&rgmii2_pins>; - pinctrl-names = "default"; - - mtd-mac-address = <&art 6>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&gmac2 { - status = "okay"; - phy-mode = "sgmii"; - qcom,id = <2>; - qcom,phy_mdio_addr = <0>; /* none */ - qcom,poll_required = <0>; /* no polling */ - qcom,rgmii_delay = <0>; - qcom,phy_mii_type = <1>; - qcom,emulation = <0>; - qcom,irq = <258>; - mdiobus = <&mdio0>; - - mtd-mac-address = <&art 0>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&adm_dma { - status = "okay"; -}; - -&sata_phy { - status = "okay"; -}; - -&sata { - status = "okay"; -}; - -&usb3_0 { - status = "okay"; - - pinctrl-0 = <&usb0_pwr_en_pins>; - pinctrl-names = "default"; -}; - -&usb3_1 { - status = "okay"; - - pinctrl-0 = <&usb1_pwr_en_pins>; - pinctrl-names = "default"; -}; - -&pcie0 { - status = "okay"; - - bridge@0,0 { - reg = <0x00000000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - ranges; - - wifi@1,0 { - compatible = "pci168c,0046"; - reg = <0x00010000 0 0 0 0>; - - mtd-mac-address = <&art 6>; - mtd-mac-address-increment = <(1)>; - }; - }; -}; - -&pcie1 { - status = "okay"; - max-link-speed = <1>; - - bridge@0,0 { - reg = <0x00000000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - ranges; - - wifi@1,0 { - compatible = "pci168c,0046"; - reg = <0x00010000 0 0 0 0>; - - mtd-mac-address = <&art 6>; - mtd-mac-address-increment = <(2)>; - }; - }; -}; diff --git a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8065.dtsi b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8065.dtsi deleted file mode 100644 index ab67d504e6..0000000000 --- a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8065.dtsi +++ /dev/null @@ -1,157 +0,0 @@ -#include "qcom-ipq8064.dtsi" - -/ { - model = "Qualcomm IPQ8065"; - compatible = "qcom,ipq8065", "qcom,ipq8064"; - - aliases { - serial0 = &gsbi4_serial; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - cpus { - qcom,l2 { - qcom,l2-cpufreq = <384000000 600000000 1400000000>; - }; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - - rsvd@41200000 { - reg = <0x41200000 0x300000>; - no-map; - }; - }; -}; - -&gsbi4 { - qcom,mode = ; - status = "okay"; - - serial@16340000 { - status = "okay"; - }; - /* - * The i2c device on gsbi4 should not be enabled. - * On ipq806x designs gsbi4 i2c is meant for exclusive - * RPM usage. Turning this on in kernel manifests as - * i2c failure for the RPM. - */ -}; - -&pcie0 { - compatible = "qcom,pcie-ipq8064-v2"; -}; - -&pcie1 { - compatible = "qcom,pcie-ipq8064-v2"; -}; - -&pcie2 { - compatible = "qcom,pcie-ipq8064-v2"; -}; - -&sata { - ports-implemented = <0x1>; -}; - -&smb208_s2a { - regulator-min-microvolt = <775000>; - regulator-max-microvolt = <1275000>; -}; - -&smb208_s2b { - regulator-min-microvolt = <775000>; - regulator-max-microvolt = <1275000>; -}; - -&ss_phy_0 { - qcom,rx-eq = <2>; - qcom,tx-deamp_3_5db = <32>; - qcom,mpll = <5>; -}; - -&ss_phy_1 { - qcom,rx-eq = <2>; - qcom,tx-deamp_3_5db = <32>; - qcom,mpll = <5>; -}; - -&opp_table0 { - /* - * On ipq8065 1.2 ghz freq is not present - * Remove it to make cpufreq work and not - * complain for missing definition - */ - - /delete-node/opp-1200000000; - - opp-384000000 { - opp-microvolt-speed0-pvs0-v0 = <975000>; - opp-microvolt-speed0-pvs1-v0 = <950000>; - opp-microvolt-speed0-pvs2-v0 = <925000>; - opp-microvolt-speed0-pvs3-v0 = <900000>; - opp-microvolt-speed0-pvs4-v0 = <875000>; - opp-microvolt-speed0-pvs5-v0 = <825000>; - opp-microvolt-speed0-pvs6-v0 = <775000>; - }; - - opp-600000000 { - opp-microvolt-speed0-pvs0-v0 = <1000000>; - opp-microvolt-speed0-pvs1-v0 = <975000>; - opp-microvolt-speed0-pvs2-v0 = <950000>; - opp-microvolt-speed0-pvs3-v0 = <925000>; - opp-microvolt-speed0-pvs4-v0 = <900000>; - opp-microvolt-speed0-pvs5-v0 = <850000>; - opp-microvolt-speed0-pvs6-v0 = <800000>; - }; - - opp-800000000 { - opp-microvolt-speed0-pvs0-v0 = <1050000>; - opp-microvolt-speed0-pvs1-v0 = <1025000>; - opp-microvolt-speed0-pvs2-v0 = <1000000>; - opp-microvolt-speed0-pvs3-v0 = <975000>; - opp-microvolt-speed0-pvs4-v0 = <950000>; - opp-microvolt-speed0-pvs5-v0 = <900000>; - opp-microvolt-speed0-pvs6-v0 = <850000>; - }; - - opp-1000000000 { - opp-microvolt-speed0-pvs0-v0 = <1100000>; - opp-microvolt-speed0-pvs1-v0 = <1075000>; - opp-microvolt-speed0-pvs2-v0 = <1050000>; - opp-microvolt-speed0-pvs3-v0 = <1025000>; - opp-microvolt-speed0-pvs4-v0 = <1000000>; - opp-microvolt-speed0-pvs5-v0 = <950000>; - opp-microvolt-speed0-pvs6-v0 = <900000>; - }; - - opp-1400000000 { - opp-microvolt-speed0-pvs0-v0 = <1175000>; - opp-microvolt-speed0-pvs1-v0 = <1150000>; - opp-microvolt-speed0-pvs2-v0 = <1125000>; - opp-microvolt-speed0-pvs3-v0 = <1100000>; - opp-microvolt-speed0-pvs4-v0 = <1075000>; - opp-microvolt-speed0-pvs5-v0 = <1025000>; - opp-microvolt-speed0-pvs6-v0 = <975000>; - }; - - opp-1725000000 { - opp-hz = /bits/ 64 <1725000000>; - opp-microvolt-speed0-pvs0-v0 = <1262500>; - opp-microvolt-speed0-pvs1-v0 = <1225000>; - opp-microvolt-speed0-pvs2-v0 = <1200000>; - opp-microvolt-speed0-pvs3-v0 = <1175000>; - opp-microvolt-speed0-pvs4-v0 = <1150000>; - opp-microvolt-speed0-pvs5-v0 = <1100000>; - opp-microvolt-speed0-pvs6-v0 = <1050000>; - opp-supported-hw = <0x1>; - clock-latency-ns = <100000>; - }; -}; diff --git a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8068-ecw5410.dts b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8068-ecw5410.dts deleted file mode 100644 index 712910c261..0000000000 --- a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8068-ecw5410.dts +++ /dev/null @@ -1,339 +0,0 @@ -#include "qcom-ipq8064-v2.0.dtsi" - -#include -#include - -/ { - model = "Edgecore ECW5410"; - compatible = "edgecore,ecw5410", "qcom,ipq8064"; - - reserved-memory { - nss@40000000 { - reg = <0x40000000 0x1000000>; - no-map; - }; - - smem: smem@41000000 { - reg = <0x41000000 0x200000>; - no-map; - }; - - wifi_dump@44000000 { - reg = <0x44000000 0x600000>; - no-map; - }; - }; - - cpus { - idle-states { - CPU_SPC: spc { - status = "disabled"; - }; - }; - }; - - aliases { - serial1 = &gsbi1_serial; - mdio-gpio0 = &mdio0; - ethernet0 = &gmac3; - ethernet1 = &gmac2; - - led-boot = &led_power_green; - led-failsafe = &led_power_red; - led-running = &led_power_green; - led-upgrade = &led_power_green; - }; - - chosen { - bootargs-append = " console=ttyMSM0,115200n8 root=/dev/ubiblock0_1"; - }; - - keys { - compatible = "gpio-keys"; - pinctrl-0 = <&button_pins>; - pinctrl-names = "default"; - - reset { - label = "reset"; - gpios = <&qcom_pinmux 25 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&led_pins>; - pinctrl-names = "default"; - - led_power_green: power_green { - label = "green:power"; - gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>; - }; - - wlan2g_green { - label = "green:wlan2g"; - gpios = <&qcom_pinmux 23 GPIO_ACTIVE_LOW>; - }; - - wlan2g_yellow { - label = "yellow:wlan2g"; - gpios = <&qcom_pinmux 24 GPIO_ACTIVE_LOW>; - }; - - wlan5g_green { - label = "green:wlan5g"; - gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>; - }; - - led_power_red: power_red { - label = "red:power"; - gpios = <&qcom_pinmux 28 GPIO_ACTIVE_LOW>; - }; - - wlan5g_yellow { - label = "yellow:wlan5g"; - gpios = <&qcom_pinmux 59 GPIO_ACTIVE_LOW>; - }; - }; -}; - - -&qcom_pinmux { - spi_pins: spi_pins { - mux { - pins = "gpio18", "gpio19"; - function = "gsbi5"; - drive-strength = <10>; - bias-pull-down; - }; - - clk { - pins = "gpio21"; - function = "gsbi5"; - drive-strength = <12>; - bias-pull-down; - }; - - cs { - pins = "gpio20"; - function = "gpio"; - drive-strength = <10>; - bias-pull-up; - }; - }; - - led_pins: led_pins { - mux { - pins = "gpio16", "gpio23", "gpio24", "gpio26", - "gpio28", "gpio59"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - button_pins: button_pins { - mux { - pins = "gpio25"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; - - uart1_pins: uart1_pins { - mux { - pins = "gpio51", "gpio52", "gpio53", "gpio54"; - function = "gsbi1"; - drive-strength = <12>; - bias-none; - }; - }; -}; - -&gsbi1 { - qcom,mode = ; - status = "okay"; - - serial@12450000 { - status = "okay"; - - pinctrl-0 = <&uart1_pins>; - pinctrl-names = "default"; - }; -}; - -&gsbi5 { - qcom,mode = ; - status = "okay"; - - spi4: spi@1a280000 { - status = "okay"; - spi-max-frequency = <50000000>; - - pinctrl-0 = <&spi_pins>; - pinctrl-names = "default"; - - cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; - - m25p80@0 { - compatible = "jedec,spi-nor"; - #address-cells = <1>; - #size-cells = <1>; - spi-max-frequency = <50000000>; - reg = <0>; - - partitions { - compatible = "qcom,smem"; - }; - }; - }; -}; - -&hs_phy_0 { /* USB3 port 0 HS phy */ - status = "okay"; -}; - -&hs_phy_1 { /* USB3 port 1 HS phy */ - status = "okay"; -}; - -&ss_phy_0 { /* USB3 port 0 SS phy */ - status = "okay"; -}; - -&ss_phy_1 { /* USB3 port 1 SS phy */ - status = "okay"; -}; - -&usb3_0 { - status = "okay"; -}; - -&usb3_1 { - status = "okay"; -}; - -&pcie1 { - status = "okay"; - - /delete-property/ pinctrl-0; - /delete-property/ pinctrl-names; - /delete-property/ perst-gpios; - - bridge@0,0 { - reg = <0x00000000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - ranges; - - wifi@1,0 { - compatible = "qcom,ath10k"; - status = "okay"; - reg = <0x00010000 0 0 0 0>; - qcom,ath10k-calibration-variant = "Edgecore-ECW5410-L"; - }; - }; -}; - -&pcie2 { - status = "okay"; - - /delete-property/ pinctrl-0; - /delete-property/ pinctrl-names; - /delete-property/ perst-gpios; - - bridge@0,0 { - reg = <0x00000000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - ranges; - - wifi@1,0 { - compatible = "qcom,ath10k"; - status = "okay"; - reg = <0x00010000 0 0 0 0>; - qcom,ath10k-calibration-variant = "Edgecore-ECW5410-L"; - }; - }; -}; - -&soc { - nand@1ac00000 { - status = "okay"; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - nand@0 { - compatible = "qcom,nandcs"; - - reg = <0>; - - nand-ecc-strength = <4>; - nand-bus-width = <8>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - rootfs1@0 { - label = "rootfs1"; - reg = <0x0000000 0x4000000>; - }; - - rootfs2@4000000 { - label = "rootfs2"; - reg = <0x4000000 0x4000000>; - }; - }; - }; - }; - - mdio1: mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - - status = "okay"; - - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; - - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>; - - phy0: ethernet-phy@0 { - reg = <0>; - }; - - phy1: ethernet-phy@1 { - reg = <1>; - }; - }; -}; - -&gmac2 { - status = "okay"; - - qcom,id = <2>; - mdiobus = <&mdio0>; - - phy-mode = "sgmii"; - phy-handle = <&phy1>; -}; - -&gmac3 { - status = "okay"; - - qcom,id = <3>; - mdiobus = <&mdio1>; - - phy-mode = "sgmii"; - phy-handle = <&phy0>; -}; - -&adm_dma { - status = "okay"; -}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ap148.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ap148.dts new file mode 100644 index 0000000000..b2fdc427e2 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ap148.dts @@ -0,0 +1,121 @@ +#include "qcom-ipq8064-v1.0.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. IPQ8064/AP-148"; + compatible = "qcom,ipq8064-ap148", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; + + aliases { + mdio-gpio0 = &mdio0; + }; +}; + +&adm_dma { + status = "okay"; +}; + +&flash { + partitions { + compatible = "qcom,smem"; + }; +}; + +&usb3_0 { + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; + +&pcie0 { + status = "okay"; +}; + +&pcie1 { + status = "okay"; + max-link-speed = <1>; +}; + +&nand_controller { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand@0 { + reg = <0>; + compatible = "qcom,nandcs"; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "qcom,smem"; + }; + }; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0x6a545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; + + phy4: ethernet-phy@4 { + reg = <4>; + }; +}; + +&gmac1 { + status = "okay"; + phy-mode = "rgmii"; + qcom,id = <1>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac2 { + status = "okay"; + phy-mode = "sgmii"; + qcom,id = <2>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ap161.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ap161.dts new file mode 100644 index 0000000000..6ba3d70808 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ap161.dts @@ -0,0 +1,159 @@ +#include "qcom-ipq8064-v1.0.dtsi" + +/ { + model = "Qualcomm IPQ8064/AP161"; + compatible = "qcom,ipq8064-ap161", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; + + aliases { + mdio-gpio0 = &mdio0; + }; +}; + +&qcom_pinmux { + rgmii2_pins: rgmii2_pins { + mux { + pins = "gpio27", "gpio28", "gpio29", + "gpio30", "gpio31", "gpio32", + "gpio51", "gpio52", "gpio59", + "gpio60", "gpio61", "gpio62", + "gpio2", "gpio66"; + }; + }; +}; + +&flash { + partitions { + compatible = "qcom,smem"; + }; +}; + +&usb3_0 { + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; + +&pcie0 { + status = "okay"; +}; + +&pcie1 { + status = "okay"; + max-link-speed = <1>; +}; + +&pcie2 { + status = "okay"; +}; + +&nand_controller { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand@0 { + reg = <0>; + compatible = "qcom,nandcs"; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "qcom,smem"; + }; + }; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x20080 /* PAD6_MODE */ + 0x000e4 0x6a545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; + + phy4: ethernet-phy@4 { + reg = <4>; + qca,phy-rgmii-en; + qca,txclk-delay-en; + qca,rxclk-delay-en; + }; + + phy3: ethernet-phy@3 { + device_type = "ethernet-phy"; + reg = <3>; + }; +}; + +&gmac0 { + status = "okay"; + phy-mode = "rgmii"; + qcom,id = <0>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + mdiobus = <&mdio0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac1 { + status = "okay"; + phy-mode = "rgmii"; + qcom,id = <1>; + mdiobus = <&mdio0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac2 { + status = "okay"; + phy-mode = "sgmii"; + qcom,id = <2>; + mdiobus = <&mdio0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&adm_dma { + status = "okay"; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-c2600.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-c2600.dts new file mode 100644 index 0000000000..4ae7de604b --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-c2600.dts @@ -0,0 +1,417 @@ +#include "qcom-ipq8064-v2.0.dtsi" + +#include + +/ { + model = "TP-Link Archer C2600"; + compatible = "tplink,c2600", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + aliases { + mdio-gpio0 = &mdio0; + + led-boot = &power; + led-failsafe = &general; + led-running = &power; + led-upgrade = &general; + label-mac-device = &gmac2; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + wifi { + label = "wifi"; + gpios = <&qcom_pinmux 49 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + ledswitch { + label = "ledswitch"; + gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + lan { + label = "white:lan"; + gpios = <&qcom_pinmux 6 GPIO_ACTIVE_HIGH>; + }; + + usb4 { + label = "white:usb_4"; + gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; + }; + + usb2 { + label = "white:usb_2"; + gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; + }; + + wps { + label = "white:wps"; + gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; + }; + + wan_amber { + label = "amber:wan"; + gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>; + }; + + wan_white { + label = "white:wan"; + gpios = <&qcom_pinmux 33 GPIO_ACTIVE_LOW>; + }; + + power: power { + label = "white:power"; + gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + + general: general { + label = "white:general"; + gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&qcom_pinmux { + button_pins: button_pins { + mux { + pins = "gpio16", "gpio54", "gpio65"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio26", "gpio33", + "gpio53", "gpio66"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19", "gpio21"; + function = "gsbi5"; + bias-pull-down; + }; + + data { + pins = "gpio18", "gpio19"; + drive-strength = <10>; + }; + + cs { + pins = "gpio20"; + function = "gpio"; + drive-strength = <10>; + bias-pull-up; + }; + + clk { + pins = "gpio21"; + drive-strength = <12>; + }; + }; + + usb0_pwr_en_pin: usb0_pwr_en_pin { + mux { + pins = "gpio25"; + function = "gpio"; + drive-strength = <10>; + bias-pull-up; + output-high; + }; + }; + + usb1_pwr_en_pin: usb1_pwr_en_pin { + mux { + pins = "gpio23"; + function = "gpio"; + drive-strength = <10>; + bias-pull-up; + output-high; + }; + }; +}; + +&gsbi5 { + qcom,mode = ; + status = "okay"; + + spi5: spi@1a280000 { + status = "okay"; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; + + m25p80@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <50000000>; + reg = <0>; + + SBL1@0 { + label = "SBL1"; + reg = <0x0 0x20000>; + read-only; + }; + + MIBIB@20000 { + label = "MIBIB"; + reg = <0x20000 0x20000>; + read-only; + }; + + SBL2@40000 { + label = "SBL2"; + reg = <0x40000 0x20000>; + read-only; + }; + + SBL3@60000 { + label = "SBL3"; + reg = <0x60000 0x30000>; + read-only; + }; + + DDRCONFIG@90000 { + label = "DDRCONFIG"; + reg = <0x90000 0x10000>; + read-only; + }; + + SSD@a0000 { + label = "SSD"; + reg = <0xa0000 0x10000>; + read-only; + }; + + TZ@b0000 { + label = "TZ"; + reg = <0xb0000 0x30000>; + read-only; + }; + + RPM@e0000 { + label = "RPM"; + reg = <0xe0000 0x20000>; + read-only; + }; + + fs-uboot@100000 { + label = "fs-uboot"; + reg = <0x100000 0x70000>; + read-only; + }; + + uboot-env@170000 { + label = "uboot-env"; + reg = <0x170000 0x40000>; + read-only; + }; + + radio@1b0000 { + label = "radio"; + reg = <0x1b0000 0x40000>; + read-only; + }; + + os-image@1f0000 { + label = "os-image"; + reg = <0x1f0000 0x400000>; + }; + + rootfs@5f0000 { + label = "rootfs"; + reg = <0x5f0000 0x1900000>; + }; + + defaultmac: default-mac@1ef0000 { + label = "default-mac"; + reg = <0x1ef0000 0x00200>; + read-only; + }; + + pin@1ef0200 { + label = "pin"; + reg = <0x1ef0200 0x00200>; + read-only; + }; + + product-info@1ef0400 { + label = "product-info"; + reg = <0x1ef0400 0x0fc00>; + read-only; + }; + + partition-table@1f00000 { + label = "partition-table"; + reg = <0x1f00000 0x10000>; + read-only; + }; + + soft-version@1f10000 { + label = "soft-version"; + reg = <0x1f10000 0x10000>; + read-only; + }; + + support-list@1f20000 { + label = "support-list"; + reg = <0x1f20000 0x10000>; + read-only; + }; + + profile@1f30000 { + label = "profile"; + reg = <0x1f30000 0x10000>; + read-only; + }; + + default-config@1f40000 { + label = "default-config"; + reg = <0x1f40000 0x10000>; + read-only; + }; + + user-config@1f50000 { + label = "user-config"; + reg = <0x1f50000 0x40000>; + read-only; + }; + + qos-db@1f90000 { + label = "qos-db"; + reg = <0x1f90000 0x40000>; + read-only; + }; + + usb-config@1fd0000 { + label = "usb-config"; + reg = <0x1fd0000 0x10000>; + read-only; + }; + + log@1fe0000 { + label = "log"; + reg = <0x1fe0000 0x20000>; + read-only; + }; + }; + }; +}; + +&usb3_0 { + status = "okay"; + + pinctrl-0 = <&usb0_pwr_en_pin>; + pinctrl-names = "default"; +}; + +&usb3_1 { + status = "okay"; + + pinctrl-0 = <&usb1_pwr_en_pin>; + pinctrl-names = "default"; +}; + +&pcie0 { + status = "okay"; +}; + +&pcie1 { + status = "okay"; + max-link-speed = <1>; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0x6a545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; + + phy4: ethernet-phy@4 { + reg = <4>; + }; +}; + +&gmac1 { + status = "okay"; + phy-mode = "rgmii"; + qcom,id = <1>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + mtd-mac-address = <&defaultmac 0x8>; + mtd-mac-address-increment = <1>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac2 { + status = "okay"; + phy-mode = "sgmii"; + qcom,id = <2>; + + mtd-mac-address = <&defaultmac 0x8>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&adm_dma { + status = "okay"; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-d7800.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-d7800.dts new file mode 100644 index 0000000000..7fb871be78 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-d7800.dts @@ -0,0 +1,310 @@ +#include "qcom-ipq8064-v2.0.dtsi" + +#include + +/ { + model = "Netgear Nighthawk X4 D7800"; + compatible = "netgear,d7800", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0xe000000>; + device_type = "memory"; + }; + + aliases { + mdio-gpio0 = &mdio0; + + led-boot = &power_white; + led-failsafe = &power_amber; + led-running = &power_white; + led-upgrade = &power_amber; + }; + + chosen { + bootargs = "rootfstype=squashfs noinitrd"; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + wifi { + label = "wifi"; + gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + usb1 { + label = "white:usb1"; + gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; + }; + + usb2 { + label = "white:usb2"; + gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; + }; + + power_amber: power_amber { + label = "amber:power"; + gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; + }; + + wan_white { + label = "white:wan"; + gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; + }; + + wan_amber { + label = "amber:wan"; + gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; + }; + + wps { + label = "white:wps"; + gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; + }; + + esata { + label = "white:esata"; + gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; + }; + + power_white: power_white { + label = "white:power"; + gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + + wifi { + label = "white:wifi"; + gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&qcom_pinmux { + button_pins: button_pins { + mux { + pins = "gpio6", "gpio54", "gpio65"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23", + "gpio24","gpio26", "gpio53", "gpio64"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + usb0_pwr_en_pins: usb0_pwr_en_pins { + mux { + pins = "gpio15"; + function = "gpio"; + drive-strength = <12>; + bias-pull-down; + output-high; + }; + }; + + usb1_pwr_en_pins: usb1_pwr_en_pins { + mux { + pins = "gpio16", "gpio68"; + function = "gpio"; + drive-strength = <12>; + bias-pull-down; + output-high; + }; + }; +}; + +&sata_phy { + status = "okay"; +}; + +&sata { + status = "okay"; +}; + +&usb3_0 { + status = "okay"; + + pinctrl-0 = <&usb0_pwr_en_pins>; + pinctrl-names = "default"; +}; + +&usb3_1 { + status = "okay"; + + pinctrl-0 = <&usb1_pwr_en_pins>; + pinctrl-names = "default"; +}; + +&pcie0 { + status = "okay"; + reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&pcie0_pins>; + pinctrl-names = "default"; +}; + +&pcie1 { + status = "okay"; + reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&pcie1_pins>; + pinctrl-names = "default"; + max-link-speed = <1>; +}; + +&nand_controller { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + reg = <0>; + compatible = "qcom,nandcs"; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + qcadata@0 { + label = "qcadata"; + reg = <0x0000000 0x0c80000>; + read-only; + }; + + APPSBL@c80000 { + label = "APPSBL"; + reg = <0x0c80000 0x0500000>; + read-only; + }; + + APPSBLENV@1180000 { + label = "APPSBLENV"; + reg = <0x1180000 0x0080000>; + read-only; + }; + + art: art@1200000 { + label = "art"; + reg = <0x1200000 0x0140000>; + read-only; + }; + + artbak: art@1340000 { + label = "artbak"; + reg = <0x1340000 0x0140000>; + read-only; + }; + + kernel@1480000 { + label = "kernel"; + reg = <0x1480000 0x0400000>; + }; + + ubi@1880000 { + label = "ubi"; + reg = <0x1880000 0x1C00000>; + }; + + netgear@3480000 { + label = "netgear"; + reg = <0x3480000 0x4480000>; + read-only; + }; + + reserve@7900000 { + label = "reserve"; + reg = <0x7900000 0x0700000>; + read-only; + }; + }; + }; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0x6a545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; + + phy4: ethernet-phy@4 { + reg = <4>; + }; +}; + +&gmac1 { + status = "okay"; + phy-mode = "rgmii"; + phy-handle = <&phy4>; + qcom,id = <1>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + mtd-mac-address = <&art 6>; +}; + +&gmac2 { + status = "okay"; + phy-mode = "sgmii"; + qcom,id = <2>; + + mtd-mac-address = <&art 0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&adm_dma { + status = "okay"; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-db149.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-db149.dts new file mode 100644 index 0000000000..8e8d942fbd --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-db149.dts @@ -0,0 +1,163 @@ +#include "qcom-ipq8064-v1.0.dtsi" + +/ { + model = "Qualcomm IPQ8064/DB149"; + compatible = "qcom,ipq8064-db149", "qcom,ipq8064"; + + aliases { + serial0 = &gsbi2_serial; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; +}; + +&qcom_pinmux { + rgmii0_pins: rgmii0_pins { + mux { + pins = "gpio2", "gpio66"; + drive-strength = <8>; + bias-disable; + }; + }; +}; + +&gsbi2 { + qcom,mode = ; + status = "okay"; + + gsbi2_serial: serial@12490000 { + status = "okay"; + }; +}; + +&gsbi4 { + status = "disabled"; +}; + +&gsbi4_serial { + status = "disabled"; +}; + +&flash { + m25p,fast-read; + + partition@0 { + label = "lowlevel_init"; + reg = <0x0 0x1b0000>; + }; + + partition@1 { + label = "u-boot"; + reg = <0x1b0000 0x80000>; + }; + + partition@2 { + label = "u-boot-env"; + reg = <0x230000 0x40000>; + }; + + partition@3 { + label = "caldata"; + reg = <0x270000 0x40000>; + }; + + partition@4 { + label = "firmware"; + reg = <0x2b0000 0x1d50000>; + }; +}; + +&usb3_0 { + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; + +&pcie0 { + status = "okay"; +}; + +&pcie1 { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0x6a545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; + + phy4: ethernet-phy@4 { + reg = <4>; + }; + + phy6: ethernet-phy@6 { + reg = <6>; + }; + + phy7: ethernet-phy@7 { + reg = <7>; + }; +}; + +&gmac0 { + status = "okay"; + phy-mode = "rgmii"; + qcom,id = <0>; + phy-handle = <&phy4>; + + pinctrl-0 = <&rgmii0_pins>; + pinctrl-names = "default"; +}; + +&gmac1 { + status = "okay"; + phy-mode = "sgmii"; + qcom,id = <1>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac2 { + status = "okay"; + phy-mode = "sgmii"; + qcom,id = <2>; + phy-handle = <&phy6>; +}; + +&gmac3 { + status = "okay"; + phy-mode = "sgmii"; + qcom,id = <3>; + phy-handle = <&phy7>; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ea7500-v1.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ea7500-v1.dts new file mode 100644 index 0000000000..176807163e --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ea7500-v1.dts @@ -0,0 +1,87 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq8064-eax500.dtsi" + +/ { + model = "Linksys EA7500 V1 WiFi Router"; + compatible = "linksys,ea7500-v1", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0xe000000>; + device_type = "memory"; + }; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + chosen { + /* look for root deviceblock nbr in this bootarg */ + find-rootblock = "ubi.mtd="; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + led_power: power { + label = "white:power"; + gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + }; +}; + +&qcom_pinmux { + button_pins: button_pins { + mux { + pins = "gpio65", "gpio68"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio6"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; +}; + +&partitions { + partition@5f80000 { + label = "sysdiag"; + reg = <0x5f80000 0x100000>; + }; + + partition@6080000 { + label = "syscfg"; + reg = <0x6080000 0x1f80000>; + }; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts new file mode 100644 index 0000000000..9b01ae0328 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts @@ -0,0 +1,122 @@ +#include "qcom-ipq8064-eax500.dtsi" + +/ { + model = "Linksys EA8500 WiFi Router"; + compatible = "linksys,ea8500", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + aliases { + mdio-gpio0 = &mdio0; + + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + wifi { + label = "wifi"; + gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + wps { + label = "green:wps"; + gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; + }; + + led_power: power { + label = "white:power"; + gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + + wifi { + label = "green:wifi"; + gpios = <&qcom_pinmux 54 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&qcom_pinmux { + button_pins: button_pins { + mux { + pins = "gpio65", "gpio67", "gpio68"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio6", "gpio53", "gpio54"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; +}; + +&sata_phy { + status = "okay"; +}; + +&sata { + status = "okay"; +}; + +&partitions { + partition@5f80000 { + label = "syscfg"; + reg = <0x5f80000 0x2080000>; + }; +}; + +&mdio0 { + phy4: ethernet-phy@4 { + reg = <4>; + }; +}; + +&gmac1 { + qcom,phy_mdio_addr = <4>; + qcom,poll_required = <1>; + qcom,rgmii_delay = <0>; + qcom,emulation = <0>; +}; + +/* LAN */ +&gmac2 { + qcom,phy_mdio_addr = <0>; /* none */ + qcom,poll_required = <0>; /* no polling */ + qcom,rgmii_delay = <0>; + qcom,emulation = <0>; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-eax500.dtsi b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-eax500.dtsi new file mode 100644 index 0000000000..3e6732e9df --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-eax500.dtsi @@ -0,0 +1,204 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq8064-v2.0.dtsi" + +#include + +/ { + chosen { + bootargs = "console=ttyMSM0,115200n8"; + /* append to bootargs adding the root deviceblock nbr from bootloader */ + append-rootblock = "ubi.mtd="; + }; +}; + +&usb3_0 { + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; + +&pcie0 { + status = "okay"; + + max-link-speed = <1>; +}; + +&pcie1 { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; + +&nand_controller { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand@0 { + reg = <0>; + compatible = "qcom,nandcs"; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + nand-ecc-step-size = <512>; + + partitions: partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "SBL1"; + reg = <0x0000000 0x0040000>; + read-only; + }; + + partition@40000 { + label = "MIBIB"; + reg = <0x0040000 0x0140000>; + read-only; + }; + + partition@180000 { + label = "SBL2"; + reg = <0x0180000 0x0140000>; + read-only; + }; + + partition@2c0000 { + label = "SBL3"; + reg = <0x02c0000 0x0280000>; + read-only; + }; + + partition@540000 { + label = "DDRCONFIG"; + reg = <0x0540000 0x0120000>; + read-only; + }; + + partition@660000 { + label = "SSD"; + reg = <0x0660000 0x0120000>; + read-only; + }; + + partition@780000 { + label = "TZ"; + reg = <0x0780000 0x0280000>; + read-only; + }; + + partition@a00000 { + label = "RPM"; + reg = <0x0a00000 0x0280000>; + read-only; + }; + + art: partition@c80000 { + label = "art"; + reg = <0x0c80000 0x0140000>; + read-only; + }; + + partition@dc0000 { + label = "APPSBL"; + reg = <0x0dc0000 0x0100000>; + read-only; + }; + + partition@ec0000 { + label = "u_env"; + reg = <0x0ec0000 0x0040000>; + }; + + partition@f00000 { + label = "s_env"; + reg = <0x0f00000 0x0040000>; + }; + + partition@f40000 { + label = "devinfo"; + reg = <0x0f40000 0x0040000>; + }; + + partition@f80000 { + label = "kernel1"; + reg = <0x0f80000 0x2800000>; /* 3 MB spill to rootfs */ + }; + + partition@1280000 { + label = "rootfs1"; + reg = <0x1280000 0x2500000>; + }; + + partition@3780000 { + label = "kernel2"; + reg = <0x3780000 0x2800000>; + }; + + partition@3a80000 { + label = "rootfs2"; + reg = <0x3a80000 0x2500000>; + }; + }; + }; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x00010 0x2613a0 /* PWS_REG */ + 0x000e4 0x6a545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; +}; + +&gmac1 { + status = "okay"; + + phy-mode = "rgmii"; + qcom,id = <1>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac2 { + status = "okay"; + + phy-mode = "sgmii"; + qcom,id = <2>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&adm_dma { + status = "okay"; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7500.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7500.dts new file mode 100644 index 0000000000..ed8ab3dbfa --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7500.dts @@ -0,0 +1,291 @@ +#include "qcom-ipq8064-v1.0.dtsi" + +#include +#include + +/ { + model = "Netgear Nighthawk X4 R7500"; + compatible = "netgear,r7500", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0xe000000>; + device_type = "memory"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; + + aliases { + mdio-gpio0 = &mdio0; + + led-boot = &power_white; + led-failsafe = &power_amber; + led-running = &power_white; + led-upgrade = &power_amber; + }; + + chosen { + bootargs = "rootfstype=squashfs noinitrd"; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + wifi { + label = "wifi"; + gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + usb1 { + label = "white:usb1"; + gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; + }; + + usb2 { + label = "white:usb2"; + gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; + }; + + power_amber: power_amber { + label = "amber:power"; + gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; + }; + + wan_white { + label = "white:wan"; + gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; + }; + + wan_amber { + label = "amber:wan"; + gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; + }; + + wps { + label = "white:wps"; + gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; + }; + + esata { + label = "white:esata"; + gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; + }; + + power_white: power_white { + label = "white:power"; + gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + + wifi { + label = "white:wifi"; + gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&qcom_pinmux { + button_pins: button_pins { + mux { + pins = "gpio6", "gpio54", "gpio65"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23", + "gpio24","gpio26", "gpio53", "gpio64"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; +}; + +&gsbi5 { + status = "disabled"; + + spi@1a280000 { + status = "disabled"; + }; +}; + +&usb3_0 { + clocks = <&gcc USB30_1_MASTER_CLK>; + status = "okay"; +}; + +&usb3_1 { + clocks = <&gcc USB30_0_MASTER_CLK>; + status = "okay"; +}; + +&pcie0 { + status = "okay"; +}; + +&pcie1 { + status = "okay"; + max-link-speed = <1>; +}; + +&nand_controller { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand@0 { + reg = <0>; + compatible = "qcom,nandcs"; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + qcadata@0 { + label = "qcadata"; + reg = <0x0000000 0x0c80000>; + read-only; + }; + + APPSBL@c80000 { + label = "APPSBL"; + reg = <0x0c80000 0x0500000>; + read-only; + }; + + APPSBLENV@1180000 { + label = "APPSBLENV"; + reg = <0x1180000 0x0080000>; + read-only; + }; + + art: art@1200000 { + label = "art"; + reg = <0x1200000 0x0140000>; + read-only; + }; + + kernel@1340000 { + label = "kernel"; + reg = <0x1340000 0x0400000>; + }; + + ubi@1740000 { + label = "ubi"; + reg = <0x1740000 0x1600000>; + }; + + netgear@2d40000 { + label = "netgear"; + reg = <0x2d40000 0x0c00000>; + read-only; + }; + + reserve@3940000 { + label = "reserve"; + reg = <0x3940000 0x46c0000>; + read-only; + }; + }; + }; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0x6a545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; + + phy4: ethernet-phy@4 { + reg = <4>; + }; +}; + +&gmac1 { + status = "okay"; + phy-mode = "rgmii"; + qcom,id = <1>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + mtd-mac-address = <&art 6>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac2 { + status = "okay"; + phy-mode = "sgmii"; + qcom,id = <2>; + + mtd-mac-address = <&art 0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&tcsr { + qcom,usb-ctrl-select = ; + compatible = "qcom,tcsr"; +}; + +&adm_dma { + status = "okay"; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts new file mode 100644 index 0000000000..20a1fad7b2 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts @@ -0,0 +1,312 @@ +#include "qcom-ipq8064-v2.0.dtsi" + +#include + +/ { + model = "Netgear Nighthawk X4 R7500v2"; + compatible = "netgear,r7500v2", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + reserved-memory { + rsvd@5fe00000 { + reg = <0x5fe00000 0x200000>; + reusable; + }; + }; + + aliases { + mdio-gpio0 = &mdio0; + + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + }; + + chosen { + bootargs = "rootfstype=squashfs noinitrd"; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + wifi { + label = "wifi"; + gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + usb1 { + label = "amber:usb1"; + gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; + }; + + usb3 { + label = "amber:usb3"; + gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; + }; + + status { + label = "amber:status"; + gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; + }; + + internet { + label = "white:internet"; + gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; + }; + + wan { + label = "white:wan"; + gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; + }; + + wps { + label = "white:wps"; + gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; + }; + + esata { + label = "white:esata"; + gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; + }; + + power: power { + label = "white:power"; + gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + + wifi { + label = "white:wifi"; + gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&adm_dma { + status = "okay"; +}; + +&qcom_pinmux { + button_pins: button_pins { + mux { + pins = "gpio6", "gpio54", "gpio65"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23", + "gpio24","gpio26", "gpio53", "gpio64"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + usb0_pwr_en_pins: usb0_pwr_en_pins { + mux { + pins = "gpio15"; + function = "gpio"; + drive-strength = <12>; + bias-pull-down; + output-high; + }; + }; + + usb1_pwr_en_pins: usb1_pwr_en_pins { + mux { + pins = "gpio16", "gpio68"; + function = "gpio"; + drive-strength = <12>; + bias-pull-down; + output-high; + }; + }; +}; + +&sata_phy { + status = "okay"; +}; + +&sata { + status = "okay"; +}; + +&usb3_0 { + status = "okay"; + + pinctrl-0 = <&usb0_pwr_en_pins>; + pinctrl-names = "default"; +}; + +&usb3_1 { + status = "okay"; + + pinctrl-0 = <&usb1_pwr_en_pins>; + pinctrl-names = "default"; +}; + +&pcie0 { + status = "okay"; + reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>; + pinctrl-0 = <&pcie0_pins>; + pinctrl-names = "default"; +}; + +&pcie1 { + status = "okay"; + reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>; + pinctrl-0 = <&pcie1_pins>; + pinctrl-names = "default"; + max-link-speed = <1>; +}; + +&nand_controller { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand@0 { + reg = <0>; + compatible = "qcom,nandcs"; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + qcadata@0 { + label = "qcadata"; + reg = <0x0000000 0x0c80000>; + read-only; + }; + + APPSBL@c80000 { + label = "APPSBL"; + reg = <0x0c80000 0x0500000>; + read-only; + }; + + APPSBLENV@1180000 { + label = "APPSBLENV"; + reg = <0x1180000 0x0080000>; + read-only; + }; + + art: art@1200000 { + label = "art"; + reg = <0x1200000 0x0140000>; + read-only; + }; + + artbak: art@1340000 { + label = "artbak"; + reg = <0x1340000 0x0140000>; + read-only; + }; + + kernel@1480000 { + label = "kernel"; + reg = <0x1480000 0x0400000>; + }; + + ubi@1880000 { + label = "ubi"; + reg = <0x1880000 0x6080000>; + }; + + reserve@7900000 { + label = "reserve"; + reg = <0x7900000 0x0700000>; + read-only; + }; + }; + }; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0xaa545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; + + phy4: ethernet-phy@4 { + reg = <4>; + }; +}; + +&gmac1 { + status = "okay"; + phy-mode = "rgmii"; + qcom,id = <1>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + mtd-mac-address = <&art 6>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac2 { + status = "okay"; + phy-mode = "sgmii"; + qcom,id = <2>; + + mtd-mac-address = <&art 0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; \ No newline at end of file diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi new file mode 100644 index 0000000000..b9ee86a891 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi @@ -0,0 +1,69 @@ +#include "qcom-ipq8064.dtsi" + +/ { + aliases { + serial0 = &gsbi4_serial; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; +}; + +&gsbi4 { + qcom,mode = ; + status = "okay"; + + serial@16340000 { + status = "okay"; + }; + /* + * The i2c device on gsbi4 should not be enabled. + * On ipq806x designs gsbi4 i2c is meant for exclusive + * RPM usage. Turning this on in kernel manifests as + * i2c failure for the RPM. + */ +}; + +&CPU_SPC { + status = "okay"; +}; + +&pcie0 { + compatible = "qcom,pcie-ipq8064-v2"; +}; + +&pcie1 { + compatible = "qcom,pcie-ipq8064-v2"; +}; + +&pcie2 { + compatible = "qcom,pcie-ipq8064-v2"; +}; + +&sata { + ports-implemented = <0x1>; +}; + +&ss_phy_0 { + qcom,rx-eq = <2>; + qcom,tx-deamp_3_5db = <32>; + qcom,mpll = <5>; +}; + +&ss_phy_1 { + qcom,rx-eq = <2>; + qcom,tx-deamp_3_5db = <32>; + qcom,mpll = <5>; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts new file mode 100644 index 0000000000..ea7d0235ce --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-vr2600v.dts @@ -0,0 +1,340 @@ +#include "qcom-ipq8064-v2.0.dtsi" + +#include + +/ { + model = "TP-Link Archer VR2600v"; + compatible = "tplink,vr2600v", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + aliases { + mdio-gpio0 = &mdio0; + + led-boot = &power; + led-failsafe = &general; + led-running = &power; + led-upgrade = &general; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + wifi { + label = "wifi"; + gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + dect { + label = "dect"; + gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + ledswitch { + label = "ledswitch"; + gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + dsl { + label = "white:dsl"; + gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; + }; + + usb { + label = "white:usb"; + gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; + }; + + lan { + label = "white:lan"; + gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; + }; + + wlan2g { + label = "white:wlan2g"; + gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>; + }; + + wlan5g { + label = "white:wlan5g"; + gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>; + }; + + power: power { + label = "white:power"; + gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + + phone { + label = "white:phone"; + gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; + }; + + wan { + label = "white:wan"; + gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>; + }; + + general: general { + label = "white:general"; + gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&qcom_pinmux { + led_pins: led_pins { + mux { + pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio17", + "gpio26", "gpio53", "gpio56", "gpio66"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + button_pins: button_pins { + mux { + pins = "gpio54", "gpio64", "gpio65", "gpio67", "gpio68"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19", "gpio21"; + function = "gsbi5"; + bias-pull-down; + }; + + data { + pins = "gpio18", "gpio19"; + drive-strength = <10>; + }; + + cs { + pins = "gpio20"; + drive-strength = <10>; + bias-pull-up; + }; + + clk { + pins = "gpio21"; + drive-strength = <12>; + }; + }; +}; + +&gsbi5 { + qcom,mode = ; + status = "okay"; + + spi4: spi@1a280000 { + status = "okay"; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; + + W25Q128@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <50000000>; + reg = <0>; + + SBL1@0 { + label = "SBL1"; + reg = <0x0 0x20000>; + read-only; + }; + + MIBIB@20000 { + label = "MIBIB"; + reg = <0x20000 0x20000>; + read-only; + }; + + SBL2@40000 { + label = "SBL2"; + reg = <0x40000 0x40000>; + read-only; + }; + + SBL3@80000 { + label = "SBL3"; + reg = <0x80000 0x80000>; + read-only; + }; + + DDRCONFIG@100000 { + label = "DDRCONFIG"; + reg = <0x100000 0x10000>; + read-only; + }; + + SSD@110000 { + label = "SSD"; + reg = <0x110000 0x10000>; + read-only; + }; + + TZ@120000 { + label = "TZ"; + reg = <0x120000 0x80000>; + read-only; + }; + + RPM@1a0000 { + label = "RPM"; + reg = <0x1a0000 0x80000>; + read-only; + }; + + APPSBL@220000 { + label = "APPSBL"; + reg = <0x220000 0x80000>; + read-only; + }; + + APPSBLENV@2a0000 { + label = "APPSBLENV"; + reg = <0x2a0000 0x40000>; + read-only; + }; + + OLDART@2e0000 { + label = "OLDART"; + reg = <0x2e0000 0x40000>; + read-only; + }; + + kernel@320000 { + label = "kernel"; + reg = <0x320000 0x300000>; + }; + + rootfs@620000 { + label = "rootfs"; + reg = <0x620000 0x960000>; + }; + + defaultmac: default-mac@0xfaf100 { + label = "default-mac"; + reg = <0xfaf100 0x00200>; + read-only; + }; + + ART@fc0000 { + label = "ART"; + reg = <0xfc0000 0x40000>; + read-only; + }; + }; + }; +}; + +&usb3_0 { + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; + +&pcie0 { + status = "okay"; +}; + +&pcie1 { + status = "okay"; + max-link-speed = <1>; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0x6a545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; + + phy4: ethernet-phy@4 { + reg = <4>; + }; +}; + +&gmac1 { + status = "okay"; + phy-mode = "rgmii"; + qcom,id = <1>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + mtd-mac-address = <&defaultmac 0>; + mtd-mac-address-increment = <1>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac2 { + status = "okay"; + phy-mode = "sgmii"; + qcom,id = <2>; + + mtd-mac-address = <&defaultmac 0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&adm_dma { + status = "okay"; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts new file mode 100644 index 0000000000..1a6b7eb4d6 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts @@ -0,0 +1,370 @@ +#include "qcom-ipq8064-v2.0.dtsi" + +#include + +/ { + model = "NEC Aterm WG2600HP"; + compatible = "nec,wg2600hp", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + aliases { + mdio-gpio0 = &mdio0; + + led-boot = &power_green; + led-failsafe = &power_red; + led-running = &power_green; + led-upgrade = &power_green; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + bridge { + label = "bridge"; + gpios = <&qcom_pinmux 24 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + + converter { + label = "converter"; + gpios = <&qcom_pinmux 25 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + converter_green { + label = "green:converter"; + gpios = <&qcom_pinmux 6 GPIO_ACTIVE_HIGH>; + }; + + power_red: power_red { + label = "red:power"; + gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; + }; + + active_green { + label = "green:active"; + gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; + }; + + active_red { + label = "red:active"; + gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; + }; + + power_green: power_green { + label = "green:power"; + gpios = <&qcom_pinmux 14 GPIO_ACTIVE_HIGH>; + }; + + converter_red { + label = "red:converter"; + gpios = <&qcom_pinmux 15 GPIO_ACTIVE_HIGH>; + }; + + wlan2g_green { + label = "green:wlan2g"; + gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>; + }; + + wlan2g_red { + label = "red:wlan2g"; + gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>; + }; + + wlan5g_green { + label = "green:wlan5g"; + gpios = <&qcom_pinmux 57 GPIO_ACTIVE_HIGH>; + }; + + wlan5g_red { + label = "red:wlan5g"; + gpios = <&qcom_pinmux 58 GPIO_ACTIVE_HIGH>; + }; + + tv_green { + label = "green:tv"; + gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; + }; + + tv_red { + label = "red:tv"; + gpios = <&qcom_pinmux 65 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&adm_dma { + status = "okay"; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x06000000 /* PAD0_MODE */ + 0x0000c 0x00080080 /* PAD6_MODE */ + 0x000e4 0x0006a545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x0000004e /* PORT0_STATUS */ + 0x00094 0x0000004e /* PORT6_STATUS */ + >; + }; + + ethernet-phy@4 { + reg = <4>; + }; +}; + +&gmac1 { + status = "okay"; + + phy-mode = "rgmii"; + qcom,id = <1>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + mtd-mac-address = <&PRODUCTDATA 6>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac2 { + status = "okay"; + + phy-mode = "sgmii"; + qcom,id = <2>; + + mtd-mac-address = <&PRODUCTDATA 0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gsbi5 { + status = "okay"; + + qcom,mode = ; + + spi@1a280000 { + status = "okay"; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + spi-max-frequency = <50000000>; + reg = <0>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + SBL1@0 { + label = "SBL1"; + reg = <0x0 0x20000>; + read-only; + }; + + MIBIB@20000 { + label = "MIBIB"; + reg = <0x20000 0x20000>; + read-only; + }; + + SBL2@40000 { + label = "SBL2"; + reg = <0x40000 0x40000>; + read-only; + }; + + SBL3@80000 { + label = "SBL3"; + reg = <0x80000 0x80000>; + read-only; + }; + + DDRCONFIG@100000 { + label = "DDRCONFIG"; + reg = <0x100000 0x10000>; + read-only; + }; + + SSD@110000 { + label = "SSD"; + reg = <0x110000 0x10000>; + read-only; + }; + + TZ@120000 { + label = "TZ"; + reg = <0x120000 0x80000>; + read-only; + }; + + RPM@1a0000 { + label = "RPM"; + reg = <0x1a0000 0x80000>; + read-only; + }; + + APPSBL@220000 { + label = "APPSBL"; + reg = <0x220000 0x80000>; + read-only; + }; + + APPSBLENV@2a0000 { + label = "APPSBLENV"; + reg = <0x2a0000 0x10000>; + }; + + PRODUCTDATA: PRODUCTDATA@2b0000 { + label = "PRODUCTDATA"; + reg = <0x2b0000 0x30000>; + read-only; + }; + + ART@2e0000 { + label = "ART"; + reg = <0x2e0000 0x40000>; + read-only; + }; + + TP@320000 { + label = "TP"; + reg = <0x320000 0x40000>; + read-only; + }; + + TINY@360000 { + label = "TINY"; + reg = <0x360000 0x500000>; + read-only; + }; + + firmware@860000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x860000 0x17a0000>; + }; + }; + }; + }; +}; + +&usb3_0 { + status = "okay"; + + pinctrl-0 = <&usb_pwr_en_pins>; + pinctrl-names = "default"; +}; + +&usb3_1 { + status = "okay"; +}; + +&pcie0 { + status = "okay"; +}; + +&pcie1 { + status = "okay"; + max-link-speed = <1>; +}; + +&qcom_pinmux { + button_pins: button_pins { + mux { + pins = "gpio16", "gpio54", "gpio24", "gpio25"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio14", + "gpio15", "gpio55", "gpio56", "gpio57", "gpio58", + "gpio64", "gpio65"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + }; + + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19", "gpio21"; + function = "gsbi5"; + bias-pull-down; + }; + + data { + pins = "gpio18", "gpio19"; + drive-strength = <10>; + }; + + cs { + pins = "gpio20"; + drive-strength = <10>; + bias-pull-up; + }; + + clk { + pins = "gpio21"; + drive-strength = <12>; + }; + }; + + usb_pwr_en_pins: usb_pwr_en_pins { + mux { + pins = "gpio22"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + output-high; + }; + }; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-wpq864.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-wpq864.dts new file mode 100644 index 0000000000..739b7261a3 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-wpq864.dts @@ -0,0 +1,486 @@ +/* + * BSD LICENSE + * + * Copyright (C) 2017 Christian Mehlis + * Copyright (C) 2018 Mathias Kresin + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * 3. Neither the names of the copyright holders nor the names of any + * contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +#include "qcom-ipq8064-v1.0.dtsi" + +#include +#include + +/ { + compatible = "compex,wpq864", "qcom,ipq8064"; + model = "Compex WPQ864"; + + aliases { + mdio-gpio0 = &mdio0; + ethernet0 = &gmac1; + ethernet1 = &gmac0; + + led-boot = &led_pass; + led-failsafe = &led_fail; + led-running = &led_pass; + led-upgrade = &led_pass; + }; + + leds { + compatible = "gpio-leds"; + + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + rss4 { + label = "green:rss4"; + gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; + }; + + rss3 { + label = "green:rss3"; + gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + + rss2 { + label = "orange:rss2"; + gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>; + }; + + rss1 { + label = "red:rss1"; + gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; + }; + + led_pass: pass { + label = "green:pass"; + gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; + }; + + led_fail: fail { + label = "green:fail"; + gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; + }; + + usb { + label = "green:usb"; + gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; + }; + + usb-pcie { + label = "green:usb-pcie"; + gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; + }; + }; + + keys { + compatible = "gpio-keys"; + + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + beeper { + compatible = "gpio-beeper"; + + pinctrl-0 = <&beeper_pins>; + pinctrl-names = "default"; + + gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>; + }; +}; + +&rpm { + pinctrl-0 = <&rpm_pins>; + pinctrl-names = "default"; +}; + +&nand_controller { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + mt29f2g08abbeah4@0 { + compatible = "qcom,nandcs"; + + reg = <0>; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + SBL1@0 { + label = "SBL1"; + reg = <0x0000000 0x0040000>; + read-only; + }; + + MIBIB@40000 { + label = "MIBIB"; + reg = <0x0040000 0x0140000>; + read-only; + }; + + SBL2@180000 { + label = "SBL2"; + reg = <0x0180000 0x0140000>; + read-only; + }; + + SBL3@2c0000 { + label = "SBL3"; + reg = <0x02c0000 0x0280000>; + read-only; + }; + + DDRCONFIG@540000 { + label = "DDRCONFIG"; + reg = <0x0540000 0x0120000>; + read-only; + }; + + SSD@660000 { + label = "SSD"; + reg = <0x0660000 0x0120000>; + read-only; + }; + + TZ@780000 { + label = "TZ"; + reg = <0x0780000 0x0280000>; + read-only; + }; + + RPM@a00000 { + label = "RPM"; + reg = <0x0a00000 0x0280000>; + read-only; + }; + + APPSBL@c80000 { + label = "APPSBL"; + reg = <0x0c80000 0x0500000>; + read-only; + }; + + APPSBLENV@1180000 { + label = "APPSBLENV"; + reg = <0x1180000 0x0080000>; + }; + + ART@1200000 { + label = "ART"; + reg = <0x1200000 0x0140000>; + }; + + ubi@1340000 { + label = "ubi"; + reg = <0x1340000 0x4000000>; + }; + + BOOTCONFIG@5340000 { + label = "BOOTCONFIG"; + reg = <0x5340000 0x0060000>; + }; + + SBL2-1@53a0000- { + label = "SBL2_1"; + reg = <0x53a0000 0x0140000>; + read-only; + }; + + SBL3-1@54e0000 { + label = "SBL3_1"; + reg = <0x54e0000 0x0280000>; + read-only; + }; + + DDRCONFIG-1@5760000 { + label = "DDRCONFIG_1"; + reg = <0x5760000 0x0120000>; + read-only; + }; + + SSD-1@5880000 { + label = "SSD_1"; + reg = <0x5880000 0x0120000>; + read-only; + }; + + TZ-1@59a0000 { + label = "TZ_1"; + reg = <0x59a0000 0x0280000>; + read-only; + }; + + RPM-1@5c20000 { + label = "RPM_1"; + reg = <0x5c20000 0x0280000>; + read-only; + }; + + BOOTCONFIG1@5ea0000 { + label = "BOOTCONFIG1"; + reg = <0x5ea0000 0x0060000>; + }; + + APPSBL-1@5f00000 { + label = "APPSBL_1"; + reg = <0x5f00000 0x0500000>; + read-only; + }; + + ubi-1@6400000 { + label = "ubi_1"; + reg = <0x6400000 0x4000000>; + }; + + unused@a400000 { + label = "unused"; + reg = <0xa400000 0x5c00000>; + }; + }; + }; +}; + +&adm_dma { + status = "okay"; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0x6a545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; + + ethernet-phy@4 { + reg = <4>; + }; +}; + +&gmac1 { + status = "okay"; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + phy-mode = "rgmii"; + qcom,id = <1>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac2 { + status = "okay"; + + phy-mode = "sgmii"; + qcom,id = <2>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gsbi4_serial { + pinctrl-0 = <&uart0_pins>; + pinctrl-names = "default"; +}; + +&flash { + compatible = "jedec,spi-nor"; +}; + +&sata_phy { + status = "disabled"; +}; + +&sata { + status = "disabled"; +}; + +&ss_phy_0 { /* USB3 port 0 SS phy */ + status = "okay"; + + rx_eq = <2>; + tx_deamp_3_5db = <32>; + mpll = <160>; +}; + +&ss_phy_1 { /* USB3 port 1 SS phy */ + status = "okay"; + + rx_eq = <2>; + tx_deamp_3_5db = <32>; + mpll = <160>; +}; + +&pcie0 { + status = "okay"; + + /delete-property/ pinctrl-0; + /delete-property/ pinctrl-names; + /delete-property/ perst-gpios; +}; + +&pcie1 { + status = "okay"; +}; + +&pcie2 { + status = "okay"; + + /delete-property/ pinctrl-0; + /delete-property/ pinctrl-names; + /delete-property/ perst-gpios; +}; + +&qcom_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinctrl0 { + pcie0_pcie2_perst { + pins = "gpio3"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio7", "gpio8", "gpio9", "gpio22", + "gpio23", "gpio24", "gpio25", "gpio53"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + button_pins: button_pins { + mux { + pins = "gpio54"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + beeper_pins: beeper_pins { + mux { + pins = "gpio55"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + rpm_pins: rpm_pins { + mux { + pins = "gpio12", "gpio13"; + function = "gsbi4"; + drive-strength = <10>; + bias-disable; + }; + }; + + uart0_pins: uart0_pins { + mux { + pins = "gpio10", "gpio11"; + function = "gsbi4"; + drive-strength = <10>; + bias-disable; + }; + }; + + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19"; + function = "gsbi5"; + drive-strength = <10>; + bias-pull-down; + }; + + clk { + pins = "gpio21"; + function = "gsbi5"; + drive-strength = <12>; + bias-pull-down; + }; + + cs { + pins = "gpio20"; + function = "gpio"; + drive-strength = <10>; + bias-pull-up; + }; + }; +}; + +&usb3_0 { + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; + +&tcsr { + qcom,usb-ctrl-select = ; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts new file mode 100644 index 0000000000..d80bfa204d --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-wxr-2533dhp.dts @@ -0,0 +1,450 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +#include "qcom-ipq8064-v2.0.dtsi" + +#include + +/ { + model = "Buffalo WXR-2533DHP"; + compatible = "buffalo,wxr-2533dhp", "qcom,ipq8064"; + + memory@42000000 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + aliases { + led-boot = &power; + led-failsafe = &diag; + led-running = &power; + led-upgrade = &power; + }; + + chosen { + /* use "ubi_rootfs" volume in "ubi" partition as rootfs */ + bootargs = "ubi.block=0,1 root=/dev/ubiblock0_1 rootfstype=squashfs"; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + usb { + label = "green:usb"; + gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "usbport"; + trigger-sources = <&hub_port0 &hub_port1>; + }; + + guestport { + label = "green:guestport"; + gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; + }; + + diag: diag { + label = "orange:diag"; + gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; + }; + + internet_orange { + label = "orange:internet"; + gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>; + }; + + internet_white { + label = "white:internet"; + gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; + }; + + wireless_orange { + label = "orange:wireless"; + gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; + }; + + wireless_white { + label = "white:wireless"; + gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; + }; + + router_orange { + label = "orange:router"; + gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>; + }; + + router_white { + label = "white:router"; + gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>; + }; + + power: power { + label = "white:power"; + gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; + }; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + power { + label = "power"; + gpios = <&qcom_pinmux 58 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + eject { + label = "eject"; + gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + guest { + label = "guest"; + gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + ap { + label = "ap"; + gpios = <&qcom_pinmux 55 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + + router { + label = "router"; + gpios = <&qcom_pinmux 56 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + + auto { + label = "auto"; + gpios = <&qcom_pinmux 57 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + }; +}; + +&nand_controller { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + cs@0 { + reg = <0>; + compatible = "qcom,nandcs"; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + ubi@0 { + label = "ubi"; + reg = <0x0000000 0x4000000>; + }; + + rootfs_1@4000000 { + label = "rootfs_1"; + reg = <0x4000000 0x4000000>; + }; + }; + }; +}; + +&adm_dma { + status = "okay"; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x07600000 /* PAD0_MODE */ + 0x00008 0x01000000 /* PAD5_MODE */ + 0x0000c 0x00000080 /* PAD6_MODE */ + 0x00050 0xcc35cc35 /* LED_CTRL0 */ + 0x00054 0xca35ca35 /* LED_CTRL1 */ + 0x00058 0xc935c935 /* LED_CTRL2 */ + 0x0005c 0x03ffff00 /* LED_CTRL3 */ + 0x000e4 0x0006a545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x0000007e /* PORT0_STATUS */ + 0x00094 0x0000007e /* PORT6_STATUS */ + >; + }; + + ethernet-phy@4 { + reg = <4>; + }; +}; + +&gmac1 { + status = "okay"; + + phy-mode = "rgmii"; + qcom,id = <1>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + mtd-mac-address = <&ART 6>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac2 { + status = "okay"; + + phy-mode = "sgmii"; + qcom,id = <2>; + + mtd-mac-address = <&ART 0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gsbi4_serial { + pinctrl-0 = <&uart0_pins>; + pinctrl-names = "default"; +}; + +&gsbi5 { + status = "okay"; + qcom,mode = ; + + spi@1a280000 { + status = "okay"; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + spi-max-frequency = <50000000>; + reg = <0>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + SBL1@0 { + label = "SBL1"; + reg = <0x0 0x10000>; + read-only; + }; + + MIBIB@10000 { + label = "MIBIB"; + reg = <0x10000 0x20000>; + read-only; + }; + + SBL2@30000 { + label = "SBL2"; + reg = <0x30000 0x30000>; + read-only; + }; + + SBL3@60000 { + label = "SBL3"; + reg = <0x60000 0x30000>; + read-only; + }; + + DDRCONFIG@90000 { + label = "DDRCONFIG"; + reg = <0x90000 0x10000>; + read-only; + }; + + SSD@a0000 { + label = "SSD"; + reg = <0xa0000 0x10000>; + read-only; + }; + + TZ@b0000 { + label = "TZ"; + reg = <0xb0000 0x30000>; + read-only; + }; + + RPM@e0000 { + label = "RPM"; + reg = <0xe0000 0x20000>; + read-only; + }; + + APPSBL@100000 { + label = "APPSBL"; + reg = <0x100000 0x70000>; + read-only; + }; + + APPSBLENV@170000 { + label = "APPSBLENV"; + reg = <0x170000 0x10000>; + read-only; + }; + + ART: ART@180000 { + label = "ART"; + reg = <0x180000 0x40000>; + read-only; + }; + + BOOTCONFIG@1c0000 { + label = "BOOTCONFIG"; + reg = <0x1c0000 0x10000>; + read-only; + }; + + APPSBL_1@1d0000 { + label = "APPSBL_1"; + reg = <0x1d0000 0x70000>; + read-only; + }; + }; + }; + }; +}; + +&usb3_0 { + status = "okay"; + + pinctrl-0 = <&usb_pwr_en_pins>; + pinctrl-names = "default"; +}; + +&usb3_1 { + status = "okay"; +}; + +&dwc3_0 { + #address-cells = <1>; + #size-cells = <0>; + + hub_port0: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; +}; + +&dwc3_1 { + #address-cells = <1>; + #size-cells = <0>; + + hub_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; +}; + +&pcie0 { + status = "okay"; +}; + +&pcie1 { + status = "okay"; + max-link-speed = <1>; +}; + +&qcom_pinmux { + button_pins: button_pins { + mux { + pins = "gpio6", "gpio54", "gpio55", "gpio56", "gpio57", + "gpio58", "gpio64", "gpio65"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio22", + "gpio23", "gpio24", "gpio25", "gpio26", "gpio53"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + uart0_pins: uart0_pins { + mux { + pins = "gpio10", "gpio11"; + function = "gsbi4"; + drive-strength = <12>; + bias-disable; + }; + }; + + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19", "gpio21"; + function = "gsbi5"; + bias-pull-down; + }; + + data { + pins = "gpio18", "gpio19"; + drive-strength = <10>; + }; + + cs{ + pins = "gpio20"; + drive-strength = <10>; + bias-pull-up; + }; + + clk { + pins = "gpio21"; + drive-strength = <12>; + }; + }; + + usb_pwr_en_pins: usb_pwr_en_pins { + mux{ + pins = "gpio68"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + output-high; + }; + }; +}; \ No newline at end of file diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts new file mode 100644 index 0000000000..2573349f55 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts @@ -0,0 +1,310 @@ +#include "qcom-ipq8065.dtsi" + +#include + +/ { + model = "ZyXEL NBG6817"; + compatible = "zyxel,nbg6817", "qcom,ipq8065", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + aliases { + mdio-gpio0 = &mdio0; + sdcc1 = &sdcc1; + + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + }; + + chosen { + bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd"; + append-rootblock = "root=/dev/mmcblk0p"; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + wifi { + label = "wifi"; + gpios = <&qcom_pinmux 53 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + internet { + label = "white:internet"; + gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; + }; + + power: power { + label = "white:power"; + gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + + wifi2g { + label = "amber:wifi2g"; + gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>; + }; + + /* wifi2g amber from the manual is missing */ + + wifi5g { + label = "amber:wifi5g"; + gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; + }; + + /* wifi5g amber from the manual is missing */ + }; +}; + +&qcom_pinmux { + button_pins: button_pins { + mux { + pins = "gpio53", "gpio54", "gpio65"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio9", "gpio26", "gpio33", "gpio64"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + }; + + mdio0_pins: mdio0_pins { + clk { + pins = "gpio1"; + input-disable; + }; + }; + + rgmii2_pins: rgmii2_pins { + tx { + pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ; + input-disable; + }; + }; + + spi_pins: spi_pins { + cs { + pins = "gpio20"; + drive-strength = <12>; + }; + }; + + usb0_pwr_en_pins: usb0_pwr_en_pins { + mux { + pins = "gpio16", "gpio17"; + function = "gpio"; + drive-strength = <12>; + }; + + pwr { + pins = "gpio17"; + bias-pull-down; + output-high; + }; + + ovc { + pins = "gpio16"; + bias-pull-up; + }; + }; + + usb1_pwr_en_pins: usb1_pwr_en_pins { + mux { + pins = "gpio14", "gpio15"; + function = "gpio"; + drive-strength = <12>; + }; + + pwr { + pins = "gpio14"; + bias-pull-down; + output-high; + }; + + ovc { + pins = "gpio15"; + bias-pull-up; + }; + }; +}; + +&gsbi5 { + qcom,mode = ; + status = "okay"; + + spi4: spi@1a280000 { + status = "okay"; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; + + m25p80@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <51200000>; + reg = <0>; + + partitions { + compatible = "qcom,smem"; + }; + }; + }; +}; + +&usb3_0 { + status = "okay"; + + pinctrl-0 = <&usb0_pwr_en_pins>; + pinctrl-names = "default"; +}; + +&usb3_1 { + status = "okay"; + + pinctrl-0 = <&usb1_pwr_en_pins>; + pinctrl-names = "default"; +}; + +&pcie0 { + status = "okay"; + reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>; + pinctrl-0 = <&pcie0_pins>; + pinctrl-names = "default"; +}; + +&pcie1 { + status = "okay"; + reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>; + pinctrl-0 = <&pcie1_pins>; + pinctrl-names = "default"; + max-link-speed = <1>; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + + phy0: ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0xaa545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + 0x00970 0x1e864443 /* QM_PORT0_CTRL0 */ + 0x00974 0x000001c6 /* QM_PORT0_CTRL1 */ + 0x00978 0x19008643 /* QM_PORT1_CTRL0 */ + 0x0097c 0x000001c6 /* QM_PORT1_CTRL1 */ + 0x00980 0x19008643 /* QM_PORT2_CTRL0 */ + 0x00984 0x000001c6 /* QM_PORT2_CTRL1 */ + 0x00988 0x19008643 /* QM_PORT3_CTRL0 */ + 0x0098c 0x000001c6 /* QM_PORT3_CTRL1 */ + 0x00990 0x19008643 /* QM_PORT4_CTRL0 */ + 0x00994 0x000001c6 /* QM_PORT4_CTRL1 */ + 0x00998 0x1e864443 /* QM_PORT5_CTRL0 */ + 0x0099c 0x000001c6 /* QM_PORT5_CTRL1 */ + 0x009a0 0x1e864443 /* QM_PORT6_CTRL0 */ + 0x009a4 0x000001c6 /* QM_PORT6_CTRL1 */ + >; + }; + + phy4: ethernet-phy@4 { + reg = <4>; + qca,ar8327-initvals = < + 0x000e4 0x6a545 /* MAC_POWER_SEL */ + 0x0000c 0x80 /* PAD6_MODE */ + >; + }; +}; + +&gmac1 { + status = "okay"; + phy-mode = "rgmii"; + qcom,id = <1>; + qcom,phy_mdio_addr = <4>; + qcom,poll_required = <0>; + qcom,rgmii_delay = <1>; + qcom,phy_mii_type = <0>; + qcom,emulation = <0>; + qcom,irq = <255>; + mdiobus = <&mdio0>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac2 { + status = "okay"; + phy-mode = "sgmii"; + qcom,id = <2>; + qcom,phy_mdio_addr = <0>; /* none */ + qcom,poll_required = <0>; /* no polling */ + qcom,rgmii_delay = <0>; + qcom,phy_mii_type = <1>; + qcom,emulation = <0>; + qcom,irq = <258>; + mdiobus = <&mdio0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&amba { + sdcc1: sdcc@12400000 { + status = "okay"; + }; +}; + +&adm_dma { + status = "okay"; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-r7800.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-r7800.dts new file mode 100644 index 0000000000..181f6d3bde --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-r7800.dts @@ -0,0 +1,449 @@ +#include "qcom-ipq8065.dtsi" + +#include + +/ { + model = "Netgear Nighthawk X4S R7800"; + compatible = "netgear,r7800", "qcom,ipq8065", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + reserved-memory { + rsvd@5fe00000 { + reg = <0x5fe00000 0x200000>; + reusable; + }; + }; + + aliases { + mdio-gpio0 = &mdio0; + + led-boot = &power_white; + led-failsafe = &power_amber; + led-running = &power_white; + led-upgrade = &power_amber; + label-mac-device = &gmac2; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + wifi { + label = "wifi"; + gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + wakeup-source; + }; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + wakeup-source; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + wakeup-source; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + power_white: power_white { + label = "white:power"; + gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + + power_amber: power_amber { + label = "amber:power"; + gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; + }; + + wan_white { + label = "white:wan"; + gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; + }; + + wan_amber { + label = "amber:wan"; + gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; + }; + + usb1 { + label = "white:usb1"; + gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; + }; + + usb2 { + label = "white:usb2"; + gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; + }; + + esata { + label = "white:esata"; + gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; + }; + + wifi { + label = "white:wifi"; + gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; + }; + + wps { + label = "white:wps"; + gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&qcom_pinmux { + button_pins: button_pins { + mux { + pins = "gpio6", "gpio54", "gpio65"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23", + "gpio24","gpio26", "gpio53", "gpio64"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + }; + + mdio0_pins: mdio0_pins { + clk { + pins = "gpio1"; + input-disable; + }; + }; + + rgmii2_pins: rgmii2_pins { + tx { + pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ; + input-disable; + }; + }; + + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19", "gpio21"; + function = "gsbi5"; + bias-pull-down; + }; + + data { + pins = "gpio18", "gpio19"; + drive-strength = <10>; + }; + + cs { + pins = "gpio20"; + drive-strength = <10>; + bias-pull-up; + }; + + clk { + pins = "gpio21"; + drive-strength = <12>; + }; + }; + + spi6_pins: spi6_pins { + mux { + pins = "gpio55", "gpio56", "gpio58"; + function = "gsbi6"; + bias-pull-down; + }; + + mosi { + pins = "gpio55"; + drive-strength = <12>; + }; + + miso { + pins = "gpio56"; + drive-strength = <14>; + }; + + cs { + pins = "gpio57"; + drive-strength = <12>; + bias-pull-up; + }; + + clk { + pins = "gpio58"; + drive-strength = <12>; + }; + + reset { + pins = "gpio33"; + drive-strength = <10>; + bias-pull-down; + output-high; + }; + }; + + usb0_pwr_en_pins: usb0_pwr_en_pins { + mux { + pins = "gpio15"; + function = "gpio"; + drive-strength = <12>; + bias-pull-down; + output-high; + }; + }; + + usb1_pwr_en_pins: usb1_pwr_en_pins { + mux { + pins = "gpio16", "gpio68"; + function = "gpio"; + drive-strength = <12>; + bias-pull-down; + output-high; + }; + }; +}; + +&nand_controller { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand@0 { + reg = <0>; + compatible = "qcom,nandcs"; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + qcadata@0 { + label = "qcadata"; + reg = <0x0000000 0x0c80000>; + read-only; + }; + + APPSBL@c80000 { + label = "APPSBL"; + reg = <0x0c80000 0x0500000>; + read-only; + }; + + APPSBLENV@1180000 { + label = "APPSBLENV"; + reg = <0x1180000 0x0080000>; + read-only; + }; + + art: art@1200000 { + label = "art"; + reg = <0x1200000 0x0140000>; + read-only; + }; + + artbak: art@1340000 { + label = "artbak"; + reg = <0x1340000 0x0140000>; + read-only; + }; + + kernel@1480000 { + label = "kernel"; + reg = <0x1480000 0x0400000>; + }; + + ubi@1880000 { + label = "ubi"; + reg = <0x1880000 0x6080000>; + }; + + reserve@7900000 { + label = "reserve"; + reg = <0x7900000 0x0700000>; + read-only; + }; + }; + }; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0xaa545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + 0x00970 0x1e864443 /* QM_PORT0_CTRL0 */ + 0x00974 0x000001c6 /* QM_PORT0_CTRL1 */ + 0x00978 0x19008643 /* QM_PORT1_CTRL0 */ + 0x0097c 0x000001c6 /* QM_PORT1_CTRL1 */ + 0x00980 0x19008643 /* QM_PORT2_CTRL0 */ + 0x00984 0x000001c6 /* QM_PORT2_CTRL1 */ + 0x00988 0x19008643 /* QM_PORT3_CTRL0 */ + 0x0098c 0x000001c6 /* QM_PORT3_CTRL1 */ + 0x00990 0x19008643 /* QM_PORT4_CTRL0 */ + 0x00994 0x000001c6 /* QM_PORT4_CTRL1 */ + 0x00998 0x1e864443 /* QM_PORT5_CTRL0 */ + 0x0099c 0x000001c6 /* QM_PORT5_CTRL1 */ + 0x009a0 0x1e864443 /* QM_PORT6_CTRL0 */ + 0x009a4 0x000001c6 /* QM_PORT6_CTRL1 */ + >; + qca,ar8327-vlans = < + 0x1 0x5e /* VLAN1 Ports 1/2/3/4/6 */ + 0x2 0x21 /* VLAN2 Ports 0/5 */ + >; + }; + + phy4: ethernet-phy@4 { + reg = <4>; + qca,ar8327-initvals = < + 0x000e4 0x6a545 /* MAC_POWER_SEL */ + 0x0000c 0x80 /* PAD6_MODE */ + >; + }; +}; + +&gmac1 { + status = "okay"; + phy-mode = "rgmii"; + qcom,id = <1>; + qcom,phy_mdio_addr = <4>; + qcom,poll_required = <0>; + qcom,rgmii_delay = <1>; + qcom,phy_mii_type = <0>; + qcom,emulation = <0>; + qcom,irq = <255>; + mdiobus = <&mdio0>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + mtd-mac-address = <&art 6>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac2 { + status = "okay"; + phy-mode = "sgmii"; + qcom,id = <2>; + qcom,phy_mdio_addr = <0>; /* none */ + qcom,poll_required = <0>; /* no polling */ + qcom,rgmii_delay = <0>; + qcom,phy_mii_type = <1>; + qcom,emulation = <0>; + qcom,irq = <258>; + mdiobus = <&mdio0>; + + mtd-mac-address = <&art 0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&adm_dma { + status = "okay"; +}; + +&sata_phy { + status = "okay"; +}; + +&sata { + status = "okay"; +}; + +&usb3_0 { + status = "okay"; + + pinctrl-0 = <&usb0_pwr_en_pins>; + pinctrl-names = "default"; +}; + +&usb3_1 { + status = "okay"; + + pinctrl-0 = <&usb1_pwr_en_pins>; + pinctrl-names = "default"; +}; + +&pcie0 { + status = "okay"; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi@1,0 { + compatible = "pci168c,0046"; + reg = <0x00010000 0 0 0 0>; + + mtd-mac-address = <&art 6>; + mtd-mac-address-increment = <(1)>; + }; + }; +}; + +&pcie1 { + status = "okay"; + max-link-speed = <1>; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi@1,0 { + compatible = "pci168c,0046"; + reg = <0x00010000 0 0 0 0>; + + mtd-mac-address = <&art 6>; + mtd-mac-address-increment = <(2)>; + }; + }; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065.dtsi b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065.dtsi new file mode 100644 index 0000000000..ab67d504e6 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065.dtsi @@ -0,0 +1,157 @@ +#include "qcom-ipq8064.dtsi" + +/ { + model = "Qualcomm IPQ8065"; + compatible = "qcom,ipq8065", "qcom,ipq8064"; + + aliases { + serial0 = &gsbi4_serial; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + cpus { + qcom,l2 { + qcom,l2-cpufreq = <384000000 600000000 1400000000>; + }; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; +}; + +&gsbi4 { + qcom,mode = ; + status = "okay"; + + serial@16340000 { + status = "okay"; + }; + /* + * The i2c device on gsbi4 should not be enabled. + * On ipq806x designs gsbi4 i2c is meant for exclusive + * RPM usage. Turning this on in kernel manifests as + * i2c failure for the RPM. + */ +}; + +&pcie0 { + compatible = "qcom,pcie-ipq8064-v2"; +}; + +&pcie1 { + compatible = "qcom,pcie-ipq8064-v2"; +}; + +&pcie2 { + compatible = "qcom,pcie-ipq8064-v2"; +}; + +&sata { + ports-implemented = <0x1>; +}; + +&smb208_s2a { + regulator-min-microvolt = <775000>; + regulator-max-microvolt = <1275000>; +}; + +&smb208_s2b { + regulator-min-microvolt = <775000>; + regulator-max-microvolt = <1275000>; +}; + +&ss_phy_0 { + qcom,rx-eq = <2>; + qcom,tx-deamp_3_5db = <32>; + qcom,mpll = <5>; +}; + +&ss_phy_1 { + qcom,rx-eq = <2>; + qcom,tx-deamp_3_5db = <32>; + qcom,mpll = <5>; +}; + +&opp_table0 { + /* + * On ipq8065 1.2 ghz freq is not present + * Remove it to make cpufreq work and not + * complain for missing definition + */ + + /delete-node/opp-1200000000; + + opp-384000000 { + opp-microvolt-speed0-pvs0-v0 = <975000>; + opp-microvolt-speed0-pvs1-v0 = <950000>; + opp-microvolt-speed0-pvs2-v0 = <925000>; + opp-microvolt-speed0-pvs3-v0 = <900000>; + opp-microvolt-speed0-pvs4-v0 = <875000>; + opp-microvolt-speed0-pvs5-v0 = <825000>; + opp-microvolt-speed0-pvs6-v0 = <775000>; + }; + + opp-600000000 { + opp-microvolt-speed0-pvs0-v0 = <1000000>; + opp-microvolt-speed0-pvs1-v0 = <975000>; + opp-microvolt-speed0-pvs2-v0 = <950000>; + opp-microvolt-speed0-pvs3-v0 = <925000>; + opp-microvolt-speed0-pvs4-v0 = <900000>; + opp-microvolt-speed0-pvs5-v0 = <850000>; + opp-microvolt-speed0-pvs6-v0 = <800000>; + }; + + opp-800000000 { + opp-microvolt-speed0-pvs0-v0 = <1050000>; + opp-microvolt-speed0-pvs1-v0 = <1025000>; + opp-microvolt-speed0-pvs2-v0 = <1000000>; + opp-microvolt-speed0-pvs3-v0 = <975000>; + opp-microvolt-speed0-pvs4-v0 = <950000>; + opp-microvolt-speed0-pvs5-v0 = <900000>; + opp-microvolt-speed0-pvs6-v0 = <850000>; + }; + + opp-1000000000 { + opp-microvolt-speed0-pvs0-v0 = <1100000>; + opp-microvolt-speed0-pvs1-v0 = <1075000>; + opp-microvolt-speed0-pvs2-v0 = <1050000>; + opp-microvolt-speed0-pvs3-v0 = <1025000>; + opp-microvolt-speed0-pvs4-v0 = <1000000>; + opp-microvolt-speed0-pvs5-v0 = <950000>; + opp-microvolt-speed0-pvs6-v0 = <900000>; + }; + + opp-1400000000 { + opp-microvolt-speed0-pvs0-v0 = <1175000>; + opp-microvolt-speed0-pvs1-v0 = <1150000>; + opp-microvolt-speed0-pvs2-v0 = <1125000>; + opp-microvolt-speed0-pvs3-v0 = <1100000>; + opp-microvolt-speed0-pvs4-v0 = <1075000>; + opp-microvolt-speed0-pvs5-v0 = <1025000>; + opp-microvolt-speed0-pvs6-v0 = <975000>; + }; + + opp-1725000000 { + opp-hz = /bits/ 64 <1725000000>; + opp-microvolt-speed0-pvs0-v0 = <1262500>; + opp-microvolt-speed0-pvs1-v0 = <1225000>; + opp-microvolt-speed0-pvs2-v0 = <1200000>; + opp-microvolt-speed0-pvs3-v0 = <1175000>; + opp-microvolt-speed0-pvs4-v0 = <1150000>; + opp-microvolt-speed0-pvs5-v0 = <1100000>; + opp-microvolt-speed0-pvs6-v0 = <1050000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <100000>; + }; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8068-ecw5410.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8068-ecw5410.dts new file mode 100644 index 0000000000..712910c261 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8068-ecw5410.dts @@ -0,0 +1,339 @@ +#include "qcom-ipq8064-v2.0.dtsi" + +#include +#include + +/ { + model = "Edgecore ECW5410"; + compatible = "edgecore,ecw5410", "qcom,ipq8064"; + + reserved-memory { + nss@40000000 { + reg = <0x40000000 0x1000000>; + no-map; + }; + + smem: smem@41000000 { + reg = <0x41000000 0x200000>; + no-map; + }; + + wifi_dump@44000000 { + reg = <0x44000000 0x600000>; + no-map; + }; + }; + + cpus { + idle-states { + CPU_SPC: spc { + status = "disabled"; + }; + }; + }; + + aliases { + serial1 = &gsbi1_serial; + mdio-gpio0 = &mdio0; + ethernet0 = &gmac3; + ethernet1 = &gmac2; + + led-boot = &led_power_green; + led-failsafe = &led_power_red; + led-running = &led_power_green; + led-upgrade = &led_power_green; + }; + + chosen { + bootargs-append = " console=ttyMSM0,115200n8 root=/dev/ubiblock0_1"; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 25 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + led_power_green: power_green { + label = "green:power"; + gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>; + }; + + wlan2g_green { + label = "green:wlan2g"; + gpios = <&qcom_pinmux 23 GPIO_ACTIVE_LOW>; + }; + + wlan2g_yellow { + label = "yellow:wlan2g"; + gpios = <&qcom_pinmux 24 GPIO_ACTIVE_LOW>; + }; + + wlan5g_green { + label = "green:wlan5g"; + gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>; + }; + + led_power_red: power_red { + label = "red:power"; + gpios = <&qcom_pinmux 28 GPIO_ACTIVE_LOW>; + }; + + wlan5g_yellow { + label = "yellow:wlan5g"; + gpios = <&qcom_pinmux 59 GPIO_ACTIVE_LOW>; + }; + }; +}; + + +&qcom_pinmux { + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19"; + function = "gsbi5"; + drive-strength = <10>; + bias-pull-down; + }; + + clk { + pins = "gpio21"; + function = "gsbi5"; + drive-strength = <12>; + bias-pull-down; + }; + + cs { + pins = "gpio20"; + function = "gpio"; + drive-strength = <10>; + bias-pull-up; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio16", "gpio23", "gpio24", "gpio26", + "gpio28", "gpio59"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + button_pins: button_pins { + mux { + pins = "gpio25"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + uart1_pins: uart1_pins { + mux { + pins = "gpio51", "gpio52", "gpio53", "gpio54"; + function = "gsbi1"; + drive-strength = <12>; + bias-none; + }; + }; +}; + +&gsbi1 { + qcom,mode = ; + status = "okay"; + + serial@12450000 { + status = "okay"; + + pinctrl-0 = <&uart1_pins>; + pinctrl-names = "default"; + }; +}; + +&gsbi5 { + qcom,mode = ; + status = "okay"; + + spi4: spi@1a280000 { + status = "okay"; + spi-max-frequency = <50000000>; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; + + m25p80@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <50000000>; + reg = <0>; + + partitions { + compatible = "qcom,smem"; + }; + }; + }; +}; + +&hs_phy_0 { /* USB3 port 0 HS phy */ + status = "okay"; +}; + +&hs_phy_1 { /* USB3 port 1 HS phy */ + status = "okay"; +}; + +&ss_phy_0 { /* USB3 port 0 SS phy */ + status = "okay"; +}; + +&ss_phy_1 { /* USB3 port 1 SS phy */ + status = "okay"; +}; + +&usb3_0 { + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; + +&pcie1 { + status = "okay"; + + /delete-property/ pinctrl-0; + /delete-property/ pinctrl-names; + /delete-property/ perst-gpios; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi@1,0 { + compatible = "qcom,ath10k"; + status = "okay"; + reg = <0x00010000 0 0 0 0>; + qcom,ath10k-calibration-variant = "Edgecore-ECW5410-L"; + }; + }; +}; + +&pcie2 { + status = "okay"; + + /delete-property/ pinctrl-0; + /delete-property/ pinctrl-names; + /delete-property/ perst-gpios; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi@1,0 { + compatible = "qcom,ath10k"; + status = "okay"; + reg = <0x00010000 0 0 0 0>; + qcom,ath10k-calibration-variant = "Edgecore-ECW5410-L"; + }; + }; +}; + +&soc { + nand@1ac00000 { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand@0 { + compatible = "qcom,nandcs"; + + reg = <0>; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + rootfs1@0 { + label = "rootfs1"; + reg = <0x0000000 0x4000000>; + }; + + rootfs2@4000000 { + label = "rootfs2"; + reg = <0x4000000 0x4000000>; + }; + }; + }; + }; + + mdio1: mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; +}; + +&gmac2 { + status = "okay"; + + qcom,id = <2>; + mdiobus = <&mdio0>; + + phy-mode = "sgmii"; + phy-handle = <&phy1>; +}; + +&gmac3 { + status = "okay"; + + qcom,id = <3>; + mdiobus = <&mdio1>; + + phy-mode = "sgmii"; + phy-handle = <&phy0>; +}; + +&adm_dma { + status = "okay"; +}; diff --git a/target/linux/ipq806x/patches-4.19/0001-dtbindings-qcom_adm-Fix-channel-specifiers.patch b/target/linux/ipq806x/patches-4.19/0001-dtbindings-qcom_adm-Fix-channel-specifiers.patch deleted file mode 100644 index 83d7bbc6f4..0000000000 --- a/target/linux/ipq806x/patches-4.19/0001-dtbindings-qcom_adm-Fix-channel-specifiers.patch +++ /dev/null @@ -1,71 +0,0 @@ -From 28d0ed88f536dd639adf1b0c7c08e04be3c8f294 Mon Sep 17 00:00:00 2001 -From: Thomas Pedersen -Date: Mon, 16 May 2016 17:58:50 -0700 -Subject: [PATCH 01/69] dtbindings: qcom_adm: Fix channel specifiers - -Original patch from Andy Gross. - -This patch removes the crci information from the dma -channel property. At least one client device requires -using more than one CRCI value for a channel. This does -not match the current binding and the crci information -needs to be removed. - -Instead, the client device will provide this information -via other means. - -Signed-off-by: Andy Gross -Signed-off-by: Thomas Pedersen ---- - Documentation/devicetree/bindings/dma/qcom_adm.txt | 16 ++++++---------- - 1 file changed, 6 insertions(+), 10 deletions(-) - ---- a/Documentation/devicetree/bindings/dma/qcom_adm.txt -+++ b/Documentation/devicetree/bindings/dma/qcom_adm.txt -@@ -4,8 +4,7 @@ Required properties: - - compatible: must contain "qcom,adm" for IPQ/APQ8064 and MSM8960 - - reg: Address range for DMA registers - - interrupts: Should contain one interrupt shared by all channels --- #dma-cells: must be <2>. First cell denotes the channel number. Second cell -- denotes CRCI (client rate control interface) flow control assignment. -+- #dma-cells: must be <1>. First cell denotes the channel number. - - clocks: Should contain the core clock and interface clock. - - clock-names: Must contain "core" for the core clock and "iface" for the - interface clock. -@@ -22,7 +21,7 @@ Example: - compatible = "qcom,adm"; - reg = <0x18300000 0x100000>; - interrupts = <0 170 0>; -- #dma-cells = <2>; -+ #dma-cells = <1>; - - clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>; - clock-names = "core", "iface"; -@@ -35,15 +34,12 @@ Example: - qcom,ee = <0>; - }; - --DMA clients must use the format descripted in the dma.txt file, using a three -+DMA clients must use the format descripted in the dma.txt file, using a two - cell specifier for each channel. - --Each dmas request consists of 3 cells: -+Each dmas request consists of two cells: - 1. phandle pointing to the DMA controller - 2. channel number -- 3. CRCI assignment, if applicable. If no CRCI flow control is required, use 0. -- The CRCI is used for flow control. It identifies the peripheral device that -- is the source/destination for the transferred data. - - Example: - -@@ -55,7 +51,7 @@ Example: - - cs-gpios = <&qcom_pinmux 20 0>; - -- dmas = <&adm_dma 6 9>, -- <&adm_dma 5 10>; -+ dmas = <&adm_dma 6>, -+ <&adm_dma 5>; - dma-names = "rx", "tx"; - }; diff --git a/target/linux/ipq806x/patches-4.19/0002-dmaengine-Add-ADM-driver.patch b/target/linux/ipq806x/patches-4.19/0002-dmaengine-Add-ADM-driver.patch deleted file mode 100644 index fedb8ed798..0000000000 --- a/target/linux/ipq806x/patches-4.19/0002-dmaengine-Add-ADM-driver.patch +++ /dev/null @@ -1,966 +0,0 @@ -From 563fa24db4e529c5a3311928d73a8a90531ee527 Mon Sep 17 00:00:00 2001 -From: Thomas Pedersen -Date: Mon, 16 May 2016 17:58:51 -0700 -Subject: [PATCH 02/69] dmaengine: Add ADM driver - -Original patch by Andy Gross. - -Add the DMA engine driver for the QCOM Application Data Mover (ADM) DMA -controller found in the MSM8x60 and IPQ/APQ8064 platforms. - -The ADM supports both memory to memory transactions and memory -to/from peripheral device transactions. The controller also provides flow -control capabilities for transactions to/from peripheral devices. - -The initial release of this driver supports slave transfers to/from peripherals -and also incorporates CRCI (client rate control interface) flow control. - -Signed-off-by: Andy Gross -Signed-off-by: Thomas Pedersen ---- - drivers/dma/qcom/Kconfig | 10 + - drivers/dma/qcom/Makefile | 1 + - drivers/dma/qcom/qcom_adm.c | 900 ++++++++++++++++++++++++++++++++++++++++++++ - 3 files changed, 911 insertions(+) - create mode 100644 drivers/dma/qcom/qcom_adm.c - ---- a/drivers/dma/qcom/Kconfig -+++ b/drivers/dma/qcom/Kconfig -@@ -27,3 +27,13 @@ config QCOM_HIDMA - (user to kernel, kernel to kernel, etc.). It only supports - memcpy interface. The core is not intended for general - purpose slave DMA. -+ -+config QCOM_ADM -+ tristate "Qualcomm ADM support" -+ depends on ARCH_QCOM || (COMPILE_TEST && OF && ARM) -+ select DMA_ENGINE -+ select DMA_VIRTUAL_CHANNELS -+ ---help--- -+ Enable support for the Qualcomm ADM DMA controller. This controller -+ provides DMA capabilities for both general purpose and on-chip -+ peripheral devices. ---- a/drivers/dma/qcom/Makefile -+++ b/drivers/dma/qcom/Makefile -@@ -4,3 +4,4 @@ obj-$(CONFIG_QCOM_HIDMA_MGMT) += hdma_mg - hdma_mgmt-objs := hidma_mgmt.o hidma_mgmt_sys.o - obj-$(CONFIG_QCOM_HIDMA) += hdma.o - hdma-objs := hidma_ll.o hidma.o hidma_dbg.o -+obj-$(CONFIG_QCOM_ADM) += qcom_adm.o ---- /dev/null -+++ b/drivers/dma/qcom/qcom_adm.c -@@ -0,0 +1,914 @@ -+/* -+ * Copyright (c) 2013-2015, The Linux Foundation. All rights reserved. -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 and -+ * only version 2 as published by the Free Software Foundation. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ */ -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#include "../dmaengine.h" -+#include "../virt-dma.h" -+ -+/* ADM registers - calculated from channel number and security domain */ -+#define ADM_CHAN_MULTI 0x4 -+#define ADM_CI_MULTI 0x4 -+#define ADM_CRCI_MULTI 0x4 -+#define ADM_EE_MULTI 0x800 -+#define ADM_CHAN_OFFS(chan) (ADM_CHAN_MULTI * chan) -+#define ADM_EE_OFFS(ee) (ADM_EE_MULTI * ee) -+#define ADM_CHAN_EE_OFFS(chan, ee) (ADM_CHAN_OFFS(chan) + ADM_EE_OFFS(ee)) -+#define ADM_CHAN_OFFS(chan) (ADM_CHAN_MULTI * chan) -+#define ADM_CI_OFFS(ci) (ADM_CHAN_OFF(ci)) -+#define ADM_CH_CMD_PTR(chan, ee) (ADM_CHAN_EE_OFFS(chan, ee)) -+#define ADM_CH_RSLT(chan, ee) (0x40 + ADM_CHAN_EE_OFFS(chan, ee)) -+#define ADM_CH_FLUSH_STATE0(chan, ee) (0x80 + ADM_CHAN_EE_OFFS(chan, ee)) -+#define ADM_CH_STATUS_SD(chan, ee) (0x200 + ADM_CHAN_EE_OFFS(chan, ee)) -+#define ADM_CH_CONF(chan) (0x240 + ADM_CHAN_OFFS(chan)) -+#define ADM_CH_RSLT_CONF(chan, ee) (0x300 + ADM_CHAN_EE_OFFS(chan, ee)) -+#define ADM_SEC_DOMAIN_IRQ_STATUS(ee) (0x380 + ADM_EE_OFFS(ee)) -+#define ADM_CI_CONF(ci) (0x390 + ci * ADM_CI_MULTI) -+#define ADM_GP_CTL 0x3d8 -+#define ADM_CRCI_CTL(crci, ee) (0x400 + crci * ADM_CRCI_MULTI + \ -+ ADM_EE_OFFS(ee)) -+ -+/* channel status */ -+#define ADM_CH_STATUS_VALID BIT(1) -+ -+/* channel result */ -+#define ADM_CH_RSLT_VALID BIT(31) -+#define ADM_CH_RSLT_ERR BIT(3) -+#define ADM_CH_RSLT_FLUSH BIT(2) -+#define ADM_CH_RSLT_TPD BIT(1) -+ -+/* channel conf */ -+#define ADM_CH_CONF_SHADOW_EN BIT(12) -+#define ADM_CH_CONF_MPU_DISABLE BIT(11) -+#define ADM_CH_CONF_PERM_MPU_CONF BIT(9) -+#define ADM_CH_CONF_FORCE_RSLT_EN BIT(7) -+#define ADM_CH_CONF_SEC_DOMAIN(ee) (((ee & 0x3) << 4) | ((ee & 0x4) << 11)) -+ -+/* channel result conf */ -+#define ADM_CH_RSLT_CONF_FLUSH_EN BIT(1) -+#define ADM_CH_RSLT_CONF_IRQ_EN BIT(0) -+ -+/* CRCI CTL */ -+#define ADM_CRCI_CTL_MUX_SEL BIT(18) -+#define ADM_CRCI_CTL_RST BIT(17) -+ -+/* CI configuration */ -+#define ADM_CI_RANGE_END(x) (x << 24) -+#define ADM_CI_RANGE_START(x) (x << 16) -+#define ADM_CI_BURST_4_WORDS BIT(2) -+#define ADM_CI_BURST_8_WORDS BIT(3) -+ -+/* GP CTL */ -+#define ADM_GP_CTL_LP_EN BIT(12) -+#define ADM_GP_CTL_LP_CNT(x) (x << 8) -+ -+/* Command pointer list entry */ -+#define ADM_CPLE_LP BIT(31) -+#define ADM_CPLE_CMD_PTR_LIST BIT(29) -+ -+/* Command list entry */ -+#define ADM_CMD_LC BIT(31) -+#define ADM_CMD_DST_CRCI(n) (((n) & 0xf) << 7) -+#define ADM_CMD_SRC_CRCI(n) (((n) & 0xf) << 3) -+ -+#define ADM_CMD_TYPE_SINGLE 0x0 -+#define ADM_CMD_TYPE_BOX 0x3 -+ -+#define ADM_CRCI_MUX_SEL BIT(4) -+#define ADM_DESC_ALIGN 8 -+#define ADM_MAX_XFER (SZ_64K-1) -+#define ADM_MAX_ROWS (SZ_64K-1) -+#define ADM_MAX_CHANNELS 16 -+ -+struct adm_desc_hw_box { -+ u32 cmd; -+ u32 src_addr; -+ u32 dst_addr; -+ u32 row_len; -+ u32 num_rows; -+ u32 row_offset; -+}; -+ -+struct adm_desc_hw_single { -+ u32 cmd; -+ u32 src_addr; -+ u32 dst_addr; -+ u32 len; -+}; -+ -+struct adm_async_desc { -+ struct virt_dma_desc vd; -+ struct adm_device *adev; -+ -+ size_t length; -+ enum dma_transfer_direction dir; -+ dma_addr_t dma_addr; -+ size_t dma_len; -+ -+ void *cpl; -+ dma_addr_t cp_addr; -+ u32 crci; -+ u32 mux; -+ u32 blk_size; -+}; -+ -+struct adm_chan { -+ struct virt_dma_chan vc; -+ struct adm_device *adev; -+ -+ /* parsed from DT */ -+ u32 id; /* channel id */ -+ -+ struct adm_async_desc *curr_txd; -+ struct dma_slave_config slave; -+ struct list_head node; -+ -+ int error; -+ int initialized; -+}; -+ -+static inline struct adm_chan *to_adm_chan(struct dma_chan *common) -+{ -+ return container_of(common, struct adm_chan, vc.chan); -+} -+ -+struct adm_device { -+ void __iomem *regs; -+ struct device *dev; -+ struct dma_device common; -+ struct device_dma_parameters dma_parms; -+ struct adm_chan *channels; -+ -+ u32 ee; -+ -+ struct clk *core_clk; -+ struct clk *iface_clk; -+ -+ struct reset_control *clk_reset; -+ struct reset_control *c0_reset; -+ struct reset_control *c1_reset; -+ struct reset_control *c2_reset; -+ int irq; -+}; -+ -+/** -+ * adm_free_chan - Frees dma resources associated with the specific channel -+ * -+ * Free all allocated descriptors associated with this channel -+ * -+ */ -+static void adm_free_chan(struct dma_chan *chan) -+{ -+ /* free all queued descriptors */ -+ vchan_free_chan_resources(to_virt_chan(chan)); -+} -+ -+/** -+ * adm_get_blksize - Get block size from burst value -+ * -+ */ -+static int adm_get_blksize(unsigned int burst) -+{ -+ int ret; -+ -+ switch (burst) { -+ case 16: -+ case 32: -+ case 64: -+ case 128: -+ ret = ffs(burst>>4) - 1; -+ break; -+ case 192: -+ ret = 4; -+ break; -+ case 256: -+ ret = 5; -+ break; -+ default: -+ ret = -EINVAL; -+ break; -+ } -+ -+ return ret; -+} -+ -+/** -+ * adm_process_fc_descriptors - Process descriptors for flow controlled xfers -+ * -+ * @achan: ADM channel -+ * @desc: Descriptor memory pointer -+ * @sg: Scatterlist entry -+ * @crci: CRCI value -+ * @burst: Burst size of transaction -+ * @direction: DMA transfer direction -+ */ -+static void *adm_process_fc_descriptors(struct adm_chan *achan, -+ void *desc, struct scatterlist *sg, u32 crci, u32 burst, -+ enum dma_transfer_direction direction) -+{ -+ struct adm_desc_hw_box *box_desc = NULL; -+ struct adm_desc_hw_single *single_desc; -+ u32 remainder = sg_dma_len(sg); -+ u32 rows, row_offset, crci_cmd; -+ u32 mem_addr = sg_dma_address(sg); -+ u32 *incr_addr = &mem_addr; -+ u32 *src, *dst; -+ -+ if (direction == DMA_DEV_TO_MEM) { -+ crci_cmd = ADM_CMD_SRC_CRCI(crci); -+ row_offset = burst; -+ src = &achan->slave.src_addr; -+ dst = &mem_addr; -+ } else { -+ crci_cmd = ADM_CMD_DST_CRCI(crci); -+ row_offset = burst << 16; -+ src = &mem_addr; -+ dst = &achan->slave.dst_addr; -+ } -+ -+ while (remainder >= burst) { -+ box_desc = desc; -+ box_desc->cmd = ADM_CMD_TYPE_BOX | crci_cmd; -+ box_desc->row_offset = row_offset; -+ box_desc->src_addr = *src; -+ box_desc->dst_addr = *dst; -+ -+ rows = remainder / burst; -+ rows = min_t(u32, rows, ADM_MAX_ROWS); -+ box_desc->num_rows = rows << 16 | rows; -+ box_desc->row_len = burst << 16 | burst; -+ -+ *incr_addr += burst * rows; -+ remainder -= burst * rows; -+ desc += sizeof(*box_desc); -+ } -+ -+ /* if leftover bytes, do one single descriptor */ -+ if (remainder) { -+ single_desc = desc; -+ single_desc->cmd = ADM_CMD_TYPE_SINGLE | crci_cmd; -+ single_desc->len = remainder; -+ single_desc->src_addr = *src; -+ single_desc->dst_addr = *dst; -+ desc += sizeof(*single_desc); -+ -+ if (sg_is_last(sg)) -+ single_desc->cmd |= ADM_CMD_LC; -+ } else { -+ if (box_desc && sg_is_last(sg)) -+ box_desc->cmd |= ADM_CMD_LC; -+ } -+ -+ return desc; -+} -+ -+/** -+ * adm_process_non_fc_descriptors - Process descriptors for non-fc xfers -+ * -+ * @achan: ADM channel -+ * @desc: Descriptor memory pointer -+ * @sg: Scatterlist entry -+ * @direction: DMA transfer direction -+ */ -+static void *adm_process_non_fc_descriptors(struct adm_chan *achan, -+ void *desc, struct scatterlist *sg, -+ enum dma_transfer_direction direction) -+{ -+ struct adm_desc_hw_single *single_desc; -+ u32 remainder = sg_dma_len(sg); -+ u32 mem_addr = sg_dma_address(sg); -+ u32 *incr_addr = &mem_addr; -+ u32 *src, *dst; -+ -+ if (direction == DMA_DEV_TO_MEM) { -+ src = &achan->slave.src_addr; -+ dst = &mem_addr; -+ } else { -+ src = &mem_addr; -+ dst = &achan->slave.dst_addr; -+ } -+ -+ do { -+ single_desc = desc; -+ single_desc->cmd = ADM_CMD_TYPE_SINGLE; -+ single_desc->src_addr = *src; -+ single_desc->dst_addr = *dst; -+ single_desc->len = (remainder > ADM_MAX_XFER) ? -+ ADM_MAX_XFER : remainder; -+ -+ remainder -= single_desc->len; -+ *incr_addr += single_desc->len; -+ desc += sizeof(*single_desc); -+ } while (remainder); -+ -+ /* set last command if this is the end of the whole transaction */ -+ if (sg_is_last(sg)) -+ single_desc->cmd |= ADM_CMD_LC; -+ -+ return desc; -+} -+ -+/** -+ * adm_prep_slave_sg - Prep slave sg transaction -+ * -+ * @chan: dma channel -+ * @sgl: scatter gather list -+ * @sg_len: length of sg -+ * @direction: DMA transfer direction -+ * @flags: DMA flags -+ * @context: transfer context (unused) -+ */ -+static struct dma_async_tx_descriptor *adm_prep_slave_sg(struct dma_chan *chan, -+ struct scatterlist *sgl, unsigned int sg_len, -+ enum dma_transfer_direction direction, unsigned long flags, -+ void *context) -+{ -+ struct adm_chan *achan = to_adm_chan(chan); -+ struct adm_device *adev = achan->adev; -+ struct adm_async_desc *async_desc; -+ struct scatterlist *sg; -+ dma_addr_t cple_addr; -+ u32 i, burst; -+ u32 single_count = 0, box_count = 0, crci = 0; -+ void *desc; -+ u32 *cple; -+ int blk_size = 0; -+ -+ if (!is_slave_direction(direction)) { -+ dev_err(adev->dev, "invalid dma direction\n"); -+ return NULL; -+ } -+ -+ /* -+ * get burst value from slave configuration -+ */ -+ burst = (direction == DMA_MEM_TO_DEV) ? -+ achan->slave.dst_maxburst : -+ achan->slave.src_maxburst; -+ -+ /* if using flow control, validate burst and crci values */ -+ if (achan->slave.device_fc) { -+ -+ blk_size = adm_get_blksize(burst); -+ if (blk_size < 0) { -+ dev_err(adev->dev, "invalid burst value: %d\n", -+ burst); -+ return ERR_PTR(-EINVAL); -+ } -+ -+ crci = achan->slave.slave_id & 0xf; -+ if (!crci || achan->slave.slave_id > 0x1f) { -+ dev_err(adev->dev, "invalid crci value\n"); -+ return ERR_PTR(-EINVAL); -+ } -+ } -+ -+ /* iterate through sgs and compute allocation size of structures */ -+ for_each_sg(sgl, sg, sg_len, i) { -+ if (achan->slave.device_fc) { -+ box_count += DIV_ROUND_UP(sg_dma_len(sg) / burst, -+ ADM_MAX_ROWS); -+ if (sg_dma_len(sg) % burst) -+ single_count++; -+ } else { -+ single_count += DIV_ROUND_UP(sg_dma_len(sg), -+ ADM_MAX_XFER); -+ } -+ } -+ -+ async_desc = kzalloc(sizeof(*async_desc), GFP_ATOMIC); -+ if (!async_desc) -+ return ERR_PTR(-ENOMEM); -+ -+ if (crci) -+ async_desc->mux = achan->slave.slave_id & ADM_CRCI_MUX_SEL ? -+ ADM_CRCI_CTL_MUX_SEL : 0; -+ async_desc->crci = crci; -+ async_desc->blk_size = blk_size; -+ async_desc->dma_len = single_count * sizeof(struct adm_desc_hw_single) + -+ box_count * sizeof(struct adm_desc_hw_box) + -+ sizeof(*cple) + 2 * ADM_DESC_ALIGN; -+ -+ async_desc->cpl = kzalloc(async_desc->dma_len, GFP_ATOMIC); -+ if (!async_desc->cpl) -+ goto free; -+ -+ async_desc->adev = adev; -+ -+ /* both command list entry and descriptors must be 8 byte aligned */ -+ cple = PTR_ALIGN(async_desc->cpl, ADM_DESC_ALIGN); -+ desc = PTR_ALIGN(cple + 1, ADM_DESC_ALIGN); -+ -+ for_each_sg(sgl, sg, sg_len, i) { -+ async_desc->length += sg_dma_len(sg); -+ -+ if (achan->slave.device_fc) -+ desc = adm_process_fc_descriptors(achan, desc, sg, crci, -+ burst, direction); -+ else -+ desc = adm_process_non_fc_descriptors(achan, desc, sg, -+ direction); -+ } -+ -+ async_desc->dma_addr = dma_map_single(adev->dev, async_desc->cpl, -+ async_desc->dma_len, -+ DMA_TO_DEVICE); -+ if (dma_mapping_error(adev->dev, async_desc->dma_addr)) -+ goto free; -+ -+ cple_addr = async_desc->dma_addr + ((void *)cple - async_desc->cpl); -+ -+ /* init cmd list */ -+ dma_sync_single_for_cpu(adev->dev, cple_addr, sizeof(*cple), -+ DMA_TO_DEVICE); -+ *cple = ADM_CPLE_LP; -+ *cple |= (async_desc->dma_addr + ADM_DESC_ALIGN) >> 3; -+ dma_sync_single_for_device(adev->dev, cple_addr, sizeof(*cple), -+ DMA_TO_DEVICE); -+ -+ return vchan_tx_prep(&achan->vc, &async_desc->vd, flags); -+ -+free: -+ kfree(async_desc); -+ return ERR_PTR(-ENOMEM); -+} -+ -+/** -+ * adm_terminate_all - terminate all transactions on a channel -+ * @achan: adm dma channel -+ * -+ * Dequeues and frees all transactions, aborts current transaction -+ * No callbacks are done -+ * -+ */ -+static int adm_terminate_all(struct dma_chan *chan) -+{ -+ struct adm_chan *achan = to_adm_chan(chan); -+ struct adm_device *adev = achan->adev; -+ unsigned long flags; -+ LIST_HEAD(head); -+ -+ spin_lock_irqsave(&achan->vc.lock, flags); -+ vchan_get_all_descriptors(&achan->vc, &head); -+ -+ /* send flush command to terminate current transaction */ -+ writel_relaxed(0x0, -+ adev->regs + ADM_CH_FLUSH_STATE0(achan->id, adev->ee)); -+ -+ spin_unlock_irqrestore(&achan->vc.lock, flags); -+ -+ vchan_dma_desc_free_list(&achan->vc, &head); -+ -+ return 0; -+} -+ -+static int adm_slave_config(struct dma_chan *chan, struct dma_slave_config *cfg) -+{ -+ struct adm_chan *achan = to_adm_chan(chan); -+ unsigned long flag; -+ -+ spin_lock_irqsave(&achan->vc.lock, flag); -+ memcpy(&achan->slave, cfg, sizeof(struct dma_slave_config)); -+ spin_unlock_irqrestore(&achan->vc.lock, flag); -+ -+ return 0; -+} -+ -+/** -+ * adm_start_dma - start next transaction -+ * @achan - ADM dma channel -+ */ -+static void adm_start_dma(struct adm_chan *achan) -+{ -+ struct virt_dma_desc *vd = vchan_next_desc(&achan->vc); -+ struct adm_device *adev = achan->adev; -+ struct adm_async_desc *async_desc; -+ -+ lockdep_assert_held(&achan->vc.lock); -+ -+ if (!vd) -+ return; -+ -+ list_del(&vd->node); -+ -+ /* write next command list out to the CMD FIFO */ -+ async_desc = container_of(vd, struct adm_async_desc, vd); -+ achan->curr_txd = async_desc; -+ -+ /* reset channel error */ -+ achan->error = 0; -+ -+ if (!achan->initialized) { -+ /* enable interrupts */ -+ writel(ADM_CH_CONF_SHADOW_EN | -+ ADM_CH_CONF_PERM_MPU_CONF | -+ ADM_CH_CONF_MPU_DISABLE | -+ ADM_CH_CONF_SEC_DOMAIN(adev->ee), -+ adev->regs + ADM_CH_CONF(achan->id)); -+ -+ writel(ADM_CH_RSLT_CONF_IRQ_EN | ADM_CH_RSLT_CONF_FLUSH_EN, -+ adev->regs + ADM_CH_RSLT_CONF(achan->id, adev->ee)); -+ -+ achan->initialized = 1; -+ } -+ -+ /* set the crci block size if this transaction requires CRCI */ -+ if (async_desc->crci) { -+ writel(async_desc->mux | async_desc->blk_size, -+ adev->regs + ADM_CRCI_CTL(async_desc->crci, adev->ee)); -+ } -+ -+ /* make sure IRQ enable doesn't get reordered */ -+ wmb(); -+ -+ /* write next command list out to the CMD FIFO */ -+ writel(ALIGN(async_desc->dma_addr, ADM_DESC_ALIGN) >> 3, -+ adev->regs + ADM_CH_CMD_PTR(achan->id, adev->ee)); -+} -+ -+/** -+ * adm_dma_irq - irq handler for ADM controller -+ * @irq: IRQ of interrupt -+ * @data: callback data -+ * -+ * IRQ handler for the bam controller -+ */ -+static irqreturn_t adm_dma_irq(int irq, void *data) -+{ -+ struct adm_device *adev = data; -+ u32 srcs, i; -+ struct adm_async_desc *async_desc; -+ unsigned long flags; -+ -+ srcs = readl_relaxed(adev->regs + -+ ADM_SEC_DOMAIN_IRQ_STATUS(adev->ee)); -+ -+ for (i = 0; i < ADM_MAX_CHANNELS; i++) { -+ struct adm_chan *achan = &adev->channels[i]; -+ u32 status, result; -+ -+ if (srcs & BIT(i)) { -+ status = readl_relaxed(adev->regs + -+ ADM_CH_STATUS_SD(i, adev->ee)); -+ -+ /* if no result present, skip */ -+ if (!(status & ADM_CH_STATUS_VALID)) -+ continue; -+ -+ result = readl_relaxed(adev->regs + -+ ADM_CH_RSLT(i, adev->ee)); -+ -+ /* no valid results, skip */ -+ if (!(result & ADM_CH_RSLT_VALID)) -+ continue; -+ -+ /* flag error if transaction was flushed or failed */ -+ if (result & (ADM_CH_RSLT_ERR | ADM_CH_RSLT_FLUSH)) -+ achan->error = 1; -+ -+ spin_lock_irqsave(&achan->vc.lock, flags); -+ async_desc = achan->curr_txd; -+ -+ achan->curr_txd = NULL; -+ -+ if (async_desc) { -+ vchan_cookie_complete(&async_desc->vd); -+ -+ /* kick off next DMA */ -+ adm_start_dma(achan); -+ } -+ -+ spin_unlock_irqrestore(&achan->vc.lock, flags); -+ } -+ } -+ -+ return IRQ_HANDLED; -+} -+ -+/** -+ * adm_tx_status - returns status of transaction -+ * @chan: dma channel -+ * @cookie: transaction cookie -+ * @txstate: DMA transaction state -+ * -+ * Return status of dma transaction -+ */ -+static enum dma_status adm_tx_status(struct dma_chan *chan, dma_cookie_t cookie, -+ struct dma_tx_state *txstate) -+{ -+ struct adm_chan *achan = to_adm_chan(chan); -+ struct virt_dma_desc *vd; -+ enum dma_status ret; -+ unsigned long flags; -+ size_t residue = 0; -+ -+ ret = dma_cookie_status(chan, cookie, txstate); -+ if (ret == DMA_COMPLETE || !txstate) -+ return ret; -+ -+ spin_lock_irqsave(&achan->vc.lock, flags); -+ -+ vd = vchan_find_desc(&achan->vc, cookie); -+ if (vd) -+ residue = container_of(vd, struct adm_async_desc, vd)->length; -+ -+ spin_unlock_irqrestore(&achan->vc.lock, flags); -+ -+ /* -+ * residue is either the full length if it is in the issued list, or 0 -+ * if it is in progress. We have no reliable way of determining -+ * anything inbetween -+ */ -+ dma_set_residue(txstate, residue); -+ -+ if (achan->error) -+ return DMA_ERROR; -+ -+ return ret; -+} -+ -+/** -+ * adm_issue_pending - starts pending transactions -+ * @chan: dma channel -+ * -+ * Issues all pending transactions and starts DMA -+ */ -+static void adm_issue_pending(struct dma_chan *chan) -+{ -+ struct adm_chan *achan = to_adm_chan(chan); -+ unsigned long flags; -+ -+ spin_lock_irqsave(&achan->vc.lock, flags); -+ -+ if (vchan_issue_pending(&achan->vc) && !achan->curr_txd) -+ adm_start_dma(achan); -+ spin_unlock_irqrestore(&achan->vc.lock, flags); -+} -+ -+/** -+ * adm_dma_free_desc - free descriptor memory -+ * @vd: virtual descriptor -+ * -+ */ -+static void adm_dma_free_desc(struct virt_dma_desc *vd) -+{ -+ struct adm_async_desc *async_desc = container_of(vd, -+ struct adm_async_desc, vd); -+ -+ dma_unmap_single(async_desc->adev->dev, async_desc->dma_addr, -+ async_desc->dma_len, DMA_TO_DEVICE); -+ kfree(async_desc->cpl); -+ kfree(async_desc); -+} -+ -+static void adm_channel_init(struct adm_device *adev, struct adm_chan *achan, -+ u32 index) -+{ -+ achan->id = index; -+ achan->adev = adev; -+ -+ vchan_init(&achan->vc, &adev->common); -+ achan->vc.desc_free = adm_dma_free_desc; -+} -+ -+static int adm_dma_probe(struct platform_device *pdev) -+{ -+ struct adm_device *adev; -+ struct resource *iores; -+ int ret; -+ u32 i; -+ -+ adev = devm_kzalloc(&pdev->dev, sizeof(*adev), GFP_KERNEL); -+ if (!adev) -+ return -ENOMEM; -+ -+ adev->dev = &pdev->dev; -+ -+ iores = platform_get_resource(pdev, IORESOURCE_MEM, 0); -+ adev->regs = devm_ioremap_resource(&pdev->dev, iores); -+ if (IS_ERR(adev->regs)) -+ return PTR_ERR(adev->regs); -+ -+ adev->irq = platform_get_irq(pdev, 0); -+ if (adev->irq < 0) -+ return adev->irq; -+ -+ ret = of_property_read_u32(pdev->dev.of_node, "qcom,ee", &adev->ee); -+ if (ret) { -+ dev_err(adev->dev, "Execution environment unspecified\n"); -+ return ret; -+ } -+ -+ adev->core_clk = devm_clk_get(adev->dev, "core"); -+ if (IS_ERR(adev->core_clk)) -+ return PTR_ERR(adev->core_clk); -+ -+ ret = clk_prepare_enable(adev->core_clk); -+ if (ret) { -+ dev_err(adev->dev, "failed to prepare/enable core clock\n"); -+ return ret; -+ } -+ -+ adev->iface_clk = devm_clk_get(adev->dev, "iface"); -+ if (IS_ERR(adev->iface_clk)) { -+ ret = PTR_ERR(adev->iface_clk); -+ goto err_disable_core_clk; -+ } -+ -+ ret = clk_prepare_enable(adev->iface_clk); -+ if (ret) { -+ dev_err(adev->dev, "failed to prepare/enable iface clock\n"); -+ goto err_disable_core_clk; -+ } -+ -+ adev->clk_reset = devm_reset_control_get(&pdev->dev, "clk"); -+ if (IS_ERR(adev->clk_reset)) { -+ dev_err(adev->dev, "failed to get ADM0 reset\n"); -+ ret = PTR_ERR(adev->clk_reset); -+ goto err_disable_clks; -+ } -+ -+ adev->c0_reset = devm_reset_control_get(&pdev->dev, "c0"); -+ if (IS_ERR(adev->c0_reset)) { -+ dev_err(adev->dev, "failed to get ADM0 C0 reset\n"); -+ ret = PTR_ERR(adev->c0_reset); -+ goto err_disable_clks; -+ } -+ -+ adev->c1_reset = devm_reset_control_get(&pdev->dev, "c1"); -+ if (IS_ERR(adev->c1_reset)) { -+ dev_err(adev->dev, "failed to get ADM0 C1 reset\n"); -+ ret = PTR_ERR(adev->c1_reset); -+ goto err_disable_clks; -+ } -+ -+ adev->c2_reset = devm_reset_control_get(&pdev->dev, "c2"); -+ if (IS_ERR(adev->c2_reset)) { -+ dev_err(adev->dev, "failed to get ADM0 C2 reset\n"); -+ ret = PTR_ERR(adev->c2_reset); -+ goto err_disable_clks; -+ } -+ -+ reset_control_assert(adev->clk_reset); -+ reset_control_assert(adev->c0_reset); -+ reset_control_assert(adev->c1_reset); -+ reset_control_assert(adev->c2_reset); -+ -+ reset_control_deassert(adev->clk_reset); -+ reset_control_deassert(adev->c0_reset); -+ reset_control_deassert(adev->c1_reset); -+ reset_control_deassert(adev->c2_reset); -+ -+ adev->channels = devm_kcalloc(adev->dev, ADM_MAX_CHANNELS, -+ sizeof(*adev->channels), GFP_KERNEL); -+ -+ if (!adev->channels) { -+ ret = -ENOMEM; -+ goto err_disable_clks; -+ } -+ -+ /* allocate and initialize channels */ -+ INIT_LIST_HEAD(&adev->common.channels); -+ -+ for (i = 0; i < ADM_MAX_CHANNELS; i++) -+ adm_channel_init(adev, &adev->channels[i], i); -+ -+ /* reset CRCIs */ -+ for (i = 0; i < 16; i++) -+ writel(ADM_CRCI_CTL_RST, adev->regs + -+ ADM_CRCI_CTL(i, adev->ee)); -+ -+ /* configure client interfaces */ -+ writel(ADM_CI_RANGE_START(0x40) | ADM_CI_RANGE_END(0xb0) | -+ ADM_CI_BURST_8_WORDS, adev->regs + ADM_CI_CONF(0)); -+ writel(ADM_CI_RANGE_START(0x2a) | ADM_CI_RANGE_END(0x2c) | -+ ADM_CI_BURST_8_WORDS, adev->regs + ADM_CI_CONF(1)); -+ writel(ADM_CI_RANGE_START(0x12) | ADM_CI_RANGE_END(0x28) | -+ ADM_CI_BURST_8_WORDS, adev->regs + ADM_CI_CONF(2)); -+ writel(ADM_GP_CTL_LP_EN | ADM_GP_CTL_LP_CNT(0xf), -+ adev->regs + ADM_GP_CTL); -+ -+ ret = devm_request_irq(adev->dev, adev->irq, adm_dma_irq, -+ 0, "adm_dma", adev); -+ if (ret) -+ goto err_disable_clks; -+ -+ platform_set_drvdata(pdev, adev); -+ -+ adev->common.dev = adev->dev; -+ adev->common.dev->dma_parms = &adev->dma_parms; -+ -+ /* set capabilities */ -+ dma_cap_zero(adev->common.cap_mask); -+ dma_cap_set(DMA_SLAVE, adev->common.cap_mask); -+ dma_cap_set(DMA_PRIVATE, adev->common.cap_mask); -+ -+ /* initialize dmaengine apis */ -+ adev->common.directions = BIT(DMA_DEV_TO_MEM | DMA_MEM_TO_DEV); -+ adev->common.residue_granularity = DMA_RESIDUE_GRANULARITY_DESCRIPTOR; -+ adev->common.src_addr_widths = DMA_SLAVE_BUSWIDTH_4_BYTES; -+ adev->common.dst_addr_widths = DMA_SLAVE_BUSWIDTH_4_BYTES; -+ adev->common.device_free_chan_resources = adm_free_chan; -+ adev->common.device_prep_slave_sg = adm_prep_slave_sg; -+ adev->common.device_issue_pending = adm_issue_pending; -+ adev->common.device_tx_status = adm_tx_status; -+ adev->common.device_terminate_all = adm_terminate_all; -+ adev->common.device_config = adm_slave_config; -+ -+ ret = dma_async_device_register(&adev->common); -+ if (ret) { -+ dev_err(adev->dev, "failed to register dma async device\n"); -+ goto err_disable_clks; -+ } -+ -+ ret = of_dma_controller_register(pdev->dev.of_node, -+ of_dma_xlate_by_chan_id, -+ &adev->common); -+ if (ret) -+ goto err_unregister_dma; -+ -+ return 0; -+ -+err_unregister_dma: -+ dma_async_device_unregister(&adev->common); -+err_disable_clks: -+ clk_disable_unprepare(adev->iface_clk); -+err_disable_core_clk: -+ clk_disable_unprepare(adev->core_clk); -+ -+ return ret; -+} -+ -+static int adm_dma_remove(struct platform_device *pdev) -+{ -+ struct adm_device *adev = platform_get_drvdata(pdev); -+ struct adm_chan *achan; -+ u32 i; -+ -+ of_dma_controller_free(pdev->dev.of_node); -+ dma_async_device_unregister(&adev->common); -+ -+ for (i = 0; i < ADM_MAX_CHANNELS; i++) { -+ achan = &adev->channels[i]; -+ -+ /* mask IRQs for this channel/EE pair */ -+ writel(0, adev->regs + ADM_CH_RSLT_CONF(achan->id, adev->ee)); -+ -+ adm_terminate_all(&adev->channels[i].vc.chan); -+ } -+ -+ devm_free_irq(adev->dev, adev->irq, adev); -+ -+ clk_disable_unprepare(adev->core_clk); -+ clk_disable_unprepare(adev->iface_clk); -+ -+ return 0; -+} -+ -+static const struct of_device_id adm_of_match[] = { -+ { .compatible = "qcom,adm", }, -+ {} -+}; -+MODULE_DEVICE_TABLE(of, adm_of_match); -+ -+static struct platform_driver adm_dma_driver = { -+ .probe = adm_dma_probe, -+ .remove = adm_dma_remove, -+ .driver = { -+ .name = "adm-dma-engine", -+ .of_match_table = adm_of_match, -+ }, -+}; -+ -+module_platform_driver(adm_dma_driver); -+ -+MODULE_AUTHOR("Andy Gross "); -+MODULE_DESCRIPTION("QCOM ADM DMA engine driver"); -+MODULE_LICENSE("GPL v2"); diff --git a/target/linux/ipq806x/patches-4.19/0030-clk-Disable-i2c-device-on-gsbi4.patch b/target/linux/ipq806x/patches-4.19/0030-clk-Disable-i2c-device-on-gsbi4.patch deleted file mode 100644 index b2a6afe0dd..0000000000 --- a/target/linux/ipq806x/patches-4.19/0030-clk-Disable-i2c-device-on-gsbi4.patch +++ /dev/null @@ -1,40 +0,0 @@ -From 0c974b87829e007dc4fae94e20d488204e20e662 Mon Sep 17 00:00:00 2001 -From: John Crispin -Date: Thu, 9 Mar 2017 08:16:10 +0100 -Subject: [PATCH 30/69] clk: Disable i2c device on gsbi4 - -This patch was not annotated and comes from the v4.4 tree. - -Signed-off-by: John Crispin ---- - drivers/clk/qcom/gcc-ipq806x.c | 5 +++-- - 1 file changed, 3 insertions(+), 2 deletions(-) - ---- a/drivers/clk/qcom/gcc-ipq806x.c -+++ b/drivers/clk/qcom/gcc-ipq806x.c -@@ -294,7 +294,7 @@ static struct clk_rcg gsbi1_uart_src = { - .parent_names = gcc_pxo_pll8, - .num_parents = 2, - .ops = &clk_rcg_ops, -- .flags = CLK_SET_PARENT_GATE, -+ .flags = CLK_SET_PARENT_GATE | CLK_IGNORE_UNUSED, - }, - }, - }; -@@ -312,7 +312,7 @@ static struct clk_branch gsbi1_uart_clk - }, - .num_parents = 1, - .ops = &clk_branch_ops, -- .flags = CLK_SET_RATE_PARENT, -+ .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED, - }, - }, - }; -@@ -890,6 +890,7 @@ static struct clk_branch gsbi1_h_clk = { - .hw.init = &(struct clk_init_data){ - .name = "gsbi1_h_clk", - .ops = &clk_branch_ops, -+ .flags = CLK_IGNORE_UNUSED, - }, - }, - }; diff --git a/target/linux/ipq806x/patches-4.19/0031-mtd-add-SMEM-parser-for-QCOM-platforms.patch b/target/linux/ipq806x/patches-4.19/0031-mtd-add-SMEM-parser-for-QCOM-platforms.patch deleted file mode 100644 index a7e95513fd..0000000000 --- a/target/linux/ipq806x/patches-4.19/0031-mtd-add-SMEM-parser-for-QCOM-platforms.patch +++ /dev/null @@ -1,282 +0,0 @@ -From d8eeb4de90e968ba32d956728c866f20752cf2c3 Mon Sep 17 00:00:00 2001 -From: Mathieu Olivari -Date: Thu, 9 Mar 2017 08:18:08 +0100 -Subject: [PATCH 31/69] mtd: add SMEM parser for QCOM platforms - -On QCOM platforms using MTD devices storage (such as IPQ806x), SMEM is -used to store partition layout. This new parser can now be used to read -SMEM and use it to register an MTD layout according to its content. - -Signed-off-by: Mathieu Olivari -Signed-off-by: Ram Chandra Jangir ---- - drivers/mtd/Kconfig | 7 ++ - drivers/mtd/Makefile | 1 + - drivers/mtd/qcom_smem_part.c | 228 +++++++++++++++++++++++++++++++++++++++++++ - 3 files changed, 236 insertions(+) - create mode 100644 drivers/mtd/qcom_smem_part.c - ---- a/drivers/mtd/Kconfig -+++ b/drivers/mtd/Kconfig -@@ -193,6 +193,13 @@ config MTD_MYLOADER_PARTS - You will still need the parsing functions to be called by the driver - for your particular device. It won't happen automatically. - -+config MTD_QCOM_SMEM_PARTS -+ tristate "QCOM SMEM partitioning support" -+ depends on QCOM_SMEM -+ help -+ This provides partitions parser for QCOM devices using SMEM -+ such as IPQ806x. -+ - comment "User Modules And Translation Layers" - - # ---- /dev/null -+++ b/drivers/mtd/qcom_smem_part.c -@@ -0,0 +1,235 @@ -+/* -+ * Copyright (c) 2015, The Linux Foundation. All rights reserved. -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 and -+ * only version 2 as published by the Free Software Foundation. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ */ -+ -+#include -+#include -+#include -+ -+#include -+#include -+#include -+#include -+ -+#include -+ -+/* Processor/host identifier for the application processor */ -+#define SMEM_HOST_APPS 0 -+ -+/* SMEM items index */ -+#define SMEM_AARM_PARTITION_TABLE 9 -+#define SMEM_BOOT_FLASH_TYPE 421 -+#define SMEM_BOOT_FLASH_BLOCK_SIZE 424 -+ -+/* SMEM Flash types */ -+#define SMEM_FLASH_NAND 2 -+#define SMEM_FLASH_SPI 6 -+ -+#define SMEM_PART_NAME_SZ 16 -+#define SMEM_PARTS_MAX 32 -+ -+struct smem_partition { -+ char name[SMEM_PART_NAME_SZ]; -+ __le32 start; -+ __le32 size; -+ __le32 attr; -+}; -+ -+struct smem_partition_table { -+ u8 magic[8]; -+ __le32 version; -+ __le32 len; -+ struct smem_partition parts[SMEM_PARTS_MAX]; -+}; -+ -+/* SMEM Magic values in partition table */ -+static const u8 SMEM_PTABLE_MAGIC[] = { -+ 0xaa, 0x73, 0xee, 0x55, -+ 0xdb, 0xbd, 0x5e, 0xe3, -+}; -+ -+static int qcom_smem_get_flash_blksz(u64 **smem_blksz) -+{ -+ size_t size; -+ -+ *smem_blksz = qcom_smem_get(SMEM_HOST_APPS, SMEM_BOOT_FLASH_BLOCK_SIZE, -+ &size); -+ -+ if (IS_ERR(*smem_blksz)) { -+ pr_err("Unable to read flash blksz from SMEM\n"); -+ return -ENOENT; -+ } -+ -+ if (size != sizeof(**smem_blksz)) { -+ pr_err("Invalid flash blksz size in SMEM\n"); -+ return -EINVAL; -+ } -+ -+ return 0; -+} -+ -+static int qcom_smem_get_flash_type(u64 **smem_flash_type) -+{ -+ size_t size; -+ -+ *smem_flash_type = qcom_smem_get(SMEM_HOST_APPS, SMEM_BOOT_FLASH_TYPE, -+ &size); -+ -+ if (IS_ERR(*smem_flash_type)) { -+ pr_err("Unable to read flash type from SMEM\n"); -+ return -ENOENT; -+ } -+ -+ if (size != sizeof(**smem_flash_type)) { -+ pr_err("Invalid flash type size in SMEM\n"); -+ return -EINVAL; -+ } -+ -+ return 0; -+} -+ -+static int qcom_smem_get_flash_partitions(struct smem_partition_table **pparts) -+{ -+ size_t size; -+ -+ *pparts = qcom_smem_get(SMEM_HOST_APPS, SMEM_AARM_PARTITION_TABLE, -+ &size); -+ -+ if (IS_ERR(*pparts)) { -+ pr_err("Unable to read partition table from SMEM\n"); -+ return -ENOENT; -+ } -+ -+ return 0; -+} -+ -+static int of_dev_node_match(struct device *dev, void *data) -+{ -+ return dev->of_node == data; -+} -+ -+static bool is_spi_device(struct device_node *np) -+{ -+ struct device *dev; -+ -+ dev = bus_find_device(&spi_bus_type, NULL, np, of_dev_node_match); -+ if (!dev) -+ return false; -+ -+ put_device(dev); -+ return true; -+} -+ -+static int parse_qcom_smem_partitions(struct mtd_info *master, -+ const struct mtd_partition **pparts, -+ struct mtd_part_parser_data *data) -+{ -+ struct smem_partition_table *smem_parts; -+ u64 *smem_flash_type, *smem_blksz; -+ struct mtd_partition *mtd_parts; -+ struct device_node *of_node = master->dev.of_node; -+ int i, ret; -+ -+ /* -+ * SMEM will only store the partition table of the boot device. -+ * If this is not the boot device, do not return any partition. -+ */ -+ ret = qcom_smem_get_flash_type(&smem_flash_type); -+ if (ret < 0) -+ return ret; -+ -+ if ((*smem_flash_type == SMEM_FLASH_NAND && !mtd_type_is_nand(master)) -+ || (*smem_flash_type == SMEM_FLASH_SPI && !is_spi_device(of_node))) -+ return 0; -+ -+ /* -+ * Just for sanity purpose, make sure the block size in SMEM matches the -+ * block size of the MTD device -+ */ -+ ret = qcom_smem_get_flash_blksz(&smem_blksz); -+ if (ret < 0) -+ return ret; -+ -+ if (*smem_blksz != master->erasesize) { -+ pr_err("SMEM block size differs from MTD block size\n"); -+ return -EINVAL; -+ } -+ -+ /* Get partition pointer from SMEM */ -+ ret = qcom_smem_get_flash_partitions(&smem_parts); -+ if (ret < 0) -+ return ret; -+ -+ if (memcmp(SMEM_PTABLE_MAGIC, smem_parts->magic, -+ sizeof(SMEM_PTABLE_MAGIC))) { -+ pr_err("SMEM partition magic invalid\n"); -+ return -EINVAL; -+ } -+ -+ /* Allocate and populate the mtd structures */ -+ mtd_parts = kcalloc(le32_to_cpu(smem_parts->len), sizeof(*mtd_parts), -+ GFP_KERNEL); -+ if (!mtd_parts) -+ return -ENOMEM; -+ -+ for (i = 0; i < smem_parts->len; i++) { -+ struct smem_partition *s_part = &smem_parts->parts[i]; -+ struct mtd_partition *m_part = &mtd_parts[i]; -+ -+ m_part->name = s_part->name; -+ m_part->size = le32_to_cpu(s_part->size) * (*smem_blksz); -+ m_part->offset = le32_to_cpu(s_part->start) * (*smem_blksz); -+ -+ /* -+ * The last SMEM partition may have its size marked as -+ * something like 0xffffffff, which means "until the end of the -+ * flash device". In this case, truncate it. -+ */ -+ if (m_part->offset + m_part->size > master->size) -+ m_part->size = master->size - m_part->offset; -+ } -+ -+ *pparts = mtd_parts; -+ -+ return smem_parts->len; -+} -+ -+static const struct of_device_id qcom_smem_of_match_table[] = { -+ { .compatible = "qcom,smem" }, -+ {}, -+}; -+MODULE_DEVICE_TABLE(of, qcom_smem_of_match_table); -+ -+static struct mtd_part_parser qcom_smem_parser = { -+ .owner = THIS_MODULE, -+ .parse_fn = parse_qcom_smem_partitions, -+ .name = "qcom-smem", -+ .of_match_table = qcom_smem_of_match_table, -+}; -+ -+static int __init qcom_smem_parser_init(void) -+{ -+ register_mtd_parser(&qcom_smem_parser); -+ return 0; -+} -+ -+static void __exit qcom_smem_parser_exit(void) -+{ -+ deregister_mtd_parser(&qcom_smem_parser); -+} -+ -+module_init(qcom_smem_parser_init); -+module_exit(qcom_smem_parser_exit); -+ -+MODULE_LICENSE("GPL"); -+MODULE_AUTHOR("Mathieu Olivari "); -+MODULE_DESCRIPTION("Parsing code for SMEM based partition tables"); ---- a/drivers/mtd/Makefile -+++ b/drivers/mtd/Makefile -@@ -17,6 +17,7 @@ obj-$(CONFIG_MTD_AR7_PARTS) += ar7part.o - obj-$(CONFIG_MTD_BCM63XX_PARTS) += bcm63xxpart.o - obj-$(CONFIG_MTD_BCM47XX_PARTS) += bcm47xxpart.o - obj-$(CONFIG_MTD_MYLOADER_PARTS) += myloader.o -+obj-$(CONFIG_MTD_QCOM_SMEM_PARTS) += qcom_smem_part.o - obj-y += parsers/ - - # 'Users' - code which presents functionality to userspace. diff --git a/target/linux/ipq806x/patches-4.19/0032-phy-add-qcom-dwc3-phy.patch b/target/linux/ipq806x/patches-4.19/0032-phy-add-qcom-dwc3-phy.patch deleted file mode 100644 index 0de0878f86..0000000000 --- a/target/linux/ipq806x/patches-4.19/0032-phy-add-qcom-dwc3-phy.patch +++ /dev/null @@ -1,614 +0,0 @@ -From b9004f4fd23e4c614d71c972f3a9311665480e29 Mon Sep 17 00:00:00 2001 -From: Andy Gross -Date: Thu, 9 Mar 2017 08:19:18 +0100 -Subject: [PATCH 32/69] phy: add qcom dwc3 phy - -Signed-off-by: Andy Gross ---- - ---- a/drivers/phy/qualcomm/Kconfig -+++ b/drivers/phy/qualcomm/Kconfig -@@ -65,3 +65,15 @@ config PHY_QCOM_USB_HSIC - select GENERIC_PHY - help - Support for the USB HSIC ULPI compliant PHY on QCOM chipsets. -+ -+config PHY_QCOM_DWC3 -+ tristate "QCOM DWC3 USB PHY support" -+ depends on ARCH_QCOM -+ depends on HAS_IOMEM -+ depends on OF -+ select GENERIC_PHY -+ help -+ This option enables support for the Synopsis PHYs present inside the -+ Qualcomm USB3.0 DWC3 controller. This driver supports both HS and SS -+ PHY controllers. -+ ---- a/drivers/phy/qualcomm/Makefile -+++ b/drivers/phy/qualcomm/Makefile -@@ -9,3 +9,4 @@ obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom- - obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-20nm.o - obj-$(CONFIG_PHY_QCOM_USB_HS) += phy-qcom-usb-hs.o - obj-$(CONFIG_PHY_QCOM_USB_HSIC) += phy-qcom-usb-hsic.o -+obj-$(CONFIG_PHY_QCOM_DWC3) += phy-qcom-dwc3.o ---- /dev/null -+++ b/drivers/phy/qualcomm/phy-qcom-dwc3.c -@@ -0,0 +1,578 @@ -+/* Copyright (c) 2014-2015, Code Aurora Forum. All rights reserved. -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 and -+ * only version 2 as published by the Free Software Foundation. -+ * -+* This program is distributed in the hope that it will be useful, -+* but WITHOUT ANY WARRANTY; without even the implied warranty of -+* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+* GNU General Public License for more details. -+*/ -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+/** -+ * USB QSCRATCH Hardware registers -+ */ -+#define QSCRATCH_GENERAL_CFG (0x08) -+#define HSUSB_PHY_CTRL_REG (0x10) -+ -+/* PHY_CTRL_REG */ -+#define HSUSB_CTRL_DMSEHV_CLAMP BIT(24) -+#define HSUSB_CTRL_USB2_SUSPEND BIT(23) -+#define HSUSB_CTRL_UTMI_CLK_EN BIT(21) -+#define HSUSB_CTRL_UTMI_OTG_VBUS_VALID BIT(20) -+#define HSUSB_CTRL_USE_CLKCORE BIT(18) -+#define HSUSB_CTRL_DPSEHV_CLAMP BIT(17) -+#define HSUSB_CTRL_COMMONONN BIT(11) -+#define HSUSB_CTRL_ID_HV_CLAMP BIT(9) -+#define HSUSB_CTRL_OTGSESSVLD_CLAMP BIT(8) -+#define HSUSB_CTRL_CLAMP_EN BIT(7) -+#define HSUSB_CTRL_RETENABLEN BIT(1) -+#define HSUSB_CTRL_POR BIT(0) -+ -+/* QSCRATCH_GENERAL_CFG */ -+#define HSUSB_GCFG_XHCI_REV BIT(2) -+ -+/** -+ * USB QSCRATCH Hardware registers -+ */ -+#define SSUSB_PHY_CTRL_REG (0x30) -+#define SSUSB_PHY_PARAM_CTRL_1 (0x34) -+#define SSUSB_PHY_PARAM_CTRL_2 (0x38) -+#define CR_PROTOCOL_DATA_IN_REG (0x3c) -+#define CR_PROTOCOL_DATA_OUT_REG (0x40) -+#define CR_PROTOCOL_CAP_ADDR_REG (0x44) -+#define CR_PROTOCOL_CAP_DATA_REG (0x48) -+#define CR_PROTOCOL_READ_REG (0x4c) -+#define CR_PROTOCOL_WRITE_REG (0x50) -+ -+/* PHY_CTRL_REG */ -+#define SSUSB_CTRL_REF_USE_PAD BIT(28) -+#define SSUSB_CTRL_TEST_POWERDOWN BIT(27) -+#define SSUSB_CTRL_LANE0_PWR_PRESENT BIT(24) -+#define SSUSB_CTRL_SS_PHY_EN BIT(8) -+#define SSUSB_CTRL_SS_PHY_RESET BIT(7) -+ -+/* SSPHY control registers - Does this need 0x30? */ -+#define SSPHY_CTRL_RX_OVRD_IN_HI(lane) (0x1006 + 0x100 * lane) -+#define SSPHY_CTRL_TX_OVRD_DRV_LO(lane) (0x1002 + 0x100 * lane) -+ -+/* SSPHY SoC version specific values */ -+#define SSPHY_RX_EQ_VALUE 4 /* Override value for rx_eq */ -+#define SSPHY_TX_DEEMPH_3_5DB 23 /* Override value for transmit -+ preemphasis */ -+#define SSPHY_MPLL_VALUE 0 /* Override value for mpll */ -+ -+/* QSCRATCH PHY_PARAM_CTRL1 fields */ -+#define PHY_PARAM_CTRL1_TX_FULL_SWING_MASK 0x07f00000u -+#define PHY_PARAM_CTRL1_TX_DEEMPH_6DB_MASK 0x000fc000u -+#define PHY_PARAM_CTRL1_TX_DEEMPH_3_5DB_MASK 0x00003f00u -+#define PHY_PARAM_CTRL1_LOS_BIAS_MASK 0x000000f8u -+ -+#define PHY_PARAM_CTRL1_MASK \ -+ (PHY_PARAM_CTRL1_TX_FULL_SWING_MASK | \ -+ PHY_PARAM_CTRL1_TX_DEEMPH_6DB_MASK | \ -+ PHY_PARAM_CTRL1_TX_DEEMPH_3_5DB_MASK | \ -+ PHY_PARAM_CTRL1_LOS_BIAS_MASK) -+ -+#define PHY_PARAM_CTRL1_TX_FULL_SWING(x) \ -+ (((x) << 20) & PHY_PARAM_CTRL1_TX_FULL_SWING_MASK) -+#define PHY_PARAM_CTRL1_TX_DEEMPH_6DB(x) \ -+ (((x) << 14) & PHY_PARAM_CTRL1_TX_DEEMPH_6DB_MASK) -+#define PHY_PARAM_CTRL1_TX_DEEMPH_3_5DB(x) \ -+ (((x) << 8) & PHY_PARAM_CTRL1_TX_DEEMPH_3_5DB_MASK) -+#define PHY_PARAM_CTRL1_LOS_BIAS(x) \ -+ (((x) << 3) & PHY_PARAM_CTRL1_LOS_BIAS_MASK) -+ -+/* RX OVRD IN HI bits */ -+#define RX_OVRD_IN_HI_RX_RESET_OVRD BIT(13) -+#define RX_OVRD_IN_HI_RX_RX_RESET BIT(12) -+#define RX_OVRD_IN_HI_RX_EQ_OVRD BIT(11) -+#define RX_OVRD_IN_HI_RX_EQ_MASK 0x0700 -+#define RX_OVRD_IN_HI_RX_EQ_SHIFT 8 -+#define RX_OVRD_IN_HI_RX_EQ_EN_OVRD BIT(7) -+#define RX_OVRD_IN_HI_RX_EQ_EN BIT(6) -+#define RX_OVRD_IN_HI_RX_LOS_FILTER_OVRD BIT(5) -+#define RX_OVRD_IN_HI_RX_LOS_FILTER_MASK 0x0018 -+#define RX_OVRD_IN_HI_RX_RATE_OVRD BIT(2) -+#define RX_OVRD_IN_HI_RX_RATE_MASK 0x0003 -+ -+/* TX OVRD DRV LO register bits */ -+#define TX_OVRD_DRV_LO_AMPLITUDE_MASK 0x007F -+#define TX_OVRD_DRV_LO_PREEMPH_MASK 0x3F80 -+#define TX_OVRD_DRV_LO_PREEMPH_SHIFT 7 -+#define TX_OVRD_DRV_LO_EN BIT(14) -+ -+/* SS CAP register bits */ -+#define SS_CR_CAP_ADDR_REG BIT(0) -+#define SS_CR_CAP_DATA_REG BIT(0) -+#define SS_CR_READ_REG BIT(0) -+#define SS_CR_WRITE_REG BIT(0) -+ -+struct qcom_dwc3_usb_phy { -+ struct regmap *base; -+ struct device *dev; -+ struct clk *xo_clk; -+ struct clk *ref_clk; -+ u32 rx_eq; -+ u32 tx_deamp_3_5db; -+ u32 mpll; -+}; -+ -+struct qcom_dwc3_phy_drvdata { -+ struct phy_ops ops; -+ u32 clk_rate; -+}; -+ -+/** -+ * Write register and read back masked value to confirm it is written -+ * -+ * @base - QCOM DWC3 PHY base virtual address. -+ * @offset - register offset. -+ * @mask - register bitmask specifying what should be updated -+ * @val - value to write. -+ */ -+static inline void qcom_dwc3_phy_write_readback( -+ struct qcom_dwc3_usb_phy *phy_dwc3, u32 offset, -+ const u32 mask, u32 val) -+{ -+ u32 write_val, tmp; -+ -+ tmp = regmap_read(phy_dwc3->base, offset, &tmp); -+ tmp &= ~mask; /* retain other bits */ -+ write_val = tmp | val; -+ -+ regmap_write(phy_dwc3->base, offset, write_val); -+ -+ /* Read back to see if val was written */ -+ regmap_read(phy_dwc3->base, offset, &tmp); -+ tmp &= mask; /* clear other bits */ -+ -+ if (tmp != val) -+ dev_err(phy_dwc3->dev, "write: %x to QSCRATCH: %x FAILED\n", -+ val, offset); -+} -+ -+static int wait_for_latch(struct regmap *base, u32 addr) -+{ -+ u32 retry = 10, data; -+ -+ while (true) { -+ regmap_read(base, addr, &data); -+ if (!data) -+ break; -+ -+ if (--retry == 0) -+ return -ETIMEDOUT; -+ -+ usleep_range(10, 20); -+ } -+ -+ return 0; -+} -+ -+/** -+ * Write SSPHY register -+ * -+ * @base - QCOM DWC3 PHY base virtual address. -+ * @addr - SSPHY address to write. -+ * @val - value to write. -+ */ -+static int qcom_dwc3_ss_write_phycreg(struct qcom_dwc3_usb_phy *phy_dwc3, -+ u32 addr, u32 val) -+{ -+ int ret; -+ -+ regmap_write(phy_dwc3->base, CR_PROTOCOL_DATA_IN_REG, addr); -+ regmap_write(phy_dwc3->base, CR_PROTOCOL_CAP_ADDR_REG, SS_CR_CAP_ADDR_REG); -+ -+ ret = wait_for_latch(phy_dwc3->base, CR_PROTOCOL_CAP_ADDR_REG); -+ if (ret) -+ goto err_wait; -+ -+ regmap_write(phy_dwc3->base, CR_PROTOCOL_DATA_IN_REG, val); -+ regmap_write(phy_dwc3->base, CR_PROTOCOL_CAP_DATA_REG, SS_CR_CAP_DATA_REG); -+ -+ ret = wait_for_latch(phy_dwc3->base, CR_PROTOCOL_CAP_DATA_REG); -+ if (ret) -+ goto err_wait; -+ -+ regmap_write(phy_dwc3->base, CR_PROTOCOL_WRITE_REG, SS_CR_WRITE_REG); -+ -+ ret = wait_for_latch(phy_dwc3->base, CR_PROTOCOL_WRITE_REG); -+ -+err_wait: -+ if (ret) -+ dev_err(phy_dwc3->dev, "timeout waiting for latch\n"); -+ return ret; -+} -+ -+/** -+ * Read SSPHY register. -+ * -+ * @base - QCOM DWC3 PHY base virtual address. -+ * @addr - SSPHY address to read. -+ */ -+static int qcom_dwc3_ss_read_phycreg(struct regmap *base, u32 addr, u32 *val) -+{ -+ int ret; -+ -+ regmap_write(base, CR_PROTOCOL_DATA_IN_REG, addr); -+ regmap_write(base, CR_PROTOCOL_CAP_ADDR_REG, SS_CR_CAP_ADDR_REG); -+ -+ ret = wait_for_latch(base, CR_PROTOCOL_CAP_ADDR_REG); -+ if (ret) -+ goto err_wait; -+ -+ /* -+ * Due to hardware bug, first read of SSPHY register might be -+ * incorrect. Hence as workaround, SW should perform SSPHY register -+ * read twice, but use only second read and ignore first read. -+ */ -+ regmap_write(base, CR_PROTOCOL_READ_REG, SS_CR_READ_REG); -+ -+ ret = wait_for_latch(base, CR_PROTOCOL_READ_REG); -+ if (ret) -+ goto err_wait; -+ -+ /* throwaway read */ -+ regmap_read(base, CR_PROTOCOL_DATA_OUT_REG, &ret); -+ -+ regmap_write(base, CR_PROTOCOL_READ_REG, SS_CR_READ_REG); -+ -+ ret = wait_for_latch(base, CR_PROTOCOL_READ_REG); -+ if (ret) -+ goto err_wait; -+ -+ regmap_read(base, CR_PROTOCOL_DATA_OUT_REG, val); -+ -+err_wait: -+ return ret; -+} -+ -+static int qcom_dwc3_hs_phy_init(struct phy *phy) -+{ -+ struct qcom_dwc3_usb_phy *phy_dwc3 = phy_get_drvdata(phy); -+ int ret; -+ u32 val; -+ -+ ret = clk_prepare_enable(phy_dwc3->xo_clk); -+ if (ret) -+ return ret; -+ -+ ret = clk_prepare_enable(phy_dwc3->ref_clk); -+ if (ret) { -+ clk_disable_unprepare(phy_dwc3->xo_clk); -+ return ret; -+ } -+ -+ /* -+ * HSPHY Initialization: Enable UTMI clock, select 19.2MHz fsel -+ * enable clamping, and disable RETENTION (power-on default is ENABLED) -+ */ -+ val = HSUSB_CTRL_DPSEHV_CLAMP | HSUSB_CTRL_DMSEHV_CLAMP | -+ HSUSB_CTRL_RETENABLEN | HSUSB_CTRL_COMMONONN | -+ HSUSB_CTRL_OTGSESSVLD_CLAMP | HSUSB_CTRL_ID_HV_CLAMP | -+ HSUSB_CTRL_DPSEHV_CLAMP | HSUSB_CTRL_UTMI_OTG_VBUS_VALID | -+ HSUSB_CTRL_UTMI_CLK_EN | HSUSB_CTRL_CLAMP_EN | 0x70; -+ -+ /* use core clock if external reference is not present */ -+ if (!phy_dwc3->xo_clk) -+ val |= HSUSB_CTRL_USE_CLKCORE; -+ -+ regmap_write(phy_dwc3->base, HSUSB_PHY_CTRL_REG, val); -+ usleep_range(2000, 2200); -+ -+ /* Disable (bypass) VBUS and ID filters */ -+ regmap_write(phy_dwc3->base, QSCRATCH_GENERAL_CFG, HSUSB_GCFG_XHCI_REV); -+ -+ return 0; -+} -+ -+static int qcom_dwc3_hs_phy_exit(struct phy *phy) -+{ -+ struct qcom_dwc3_usb_phy *phy_dwc3 = phy_get_drvdata(phy); -+ -+ clk_disable_unprepare(phy_dwc3->ref_clk); -+ clk_disable_unprepare(phy_dwc3->xo_clk); -+ -+ return 0; -+} -+ -+static int qcom_dwc3_ss_phy_init(struct phy *phy) -+{ -+ struct qcom_dwc3_usb_phy *phy_dwc3 = phy_get_drvdata(phy); -+ int ret; -+ u32 data = 0; -+ -+ ret = clk_prepare_enable(phy_dwc3->xo_clk); -+ if (ret) -+ return ret; -+ -+ ret = clk_prepare_enable(phy_dwc3->ref_clk); -+ if (ret) { -+ clk_disable_unprepare(phy_dwc3->xo_clk); -+ return ret; -+ } -+ -+ /* reset phy */ -+ regmap_read(phy_dwc3->base, SSUSB_PHY_CTRL_REG, &data); -+ regmap_write(phy_dwc3->base, SSUSB_PHY_CTRL_REG, -+ data | SSUSB_CTRL_SS_PHY_RESET); -+ usleep_range(2000, 2200); -+ regmap_write(phy_dwc3->base, SSUSB_PHY_CTRL_REG, data); -+ -+ /* clear REF_PAD if we don't have XO clk */ -+ if (!phy_dwc3->xo_clk) -+ data &= ~SSUSB_CTRL_REF_USE_PAD; -+ else -+ data |= SSUSB_CTRL_REF_USE_PAD; -+ -+ regmap_write(phy_dwc3->base, SSUSB_PHY_CTRL_REG, data); -+ -+ /* wait for ref clk to become stable, this can take up to 30ms */ -+ msleep(30); -+ -+ data |= SSUSB_CTRL_SS_PHY_EN | SSUSB_CTRL_LANE0_PWR_PRESENT; -+ regmap_write(phy_dwc3->base, SSUSB_PHY_CTRL_REG, data); -+ -+ /* -+ * WORKAROUND: There is SSPHY suspend bug due to which USB enumerates -+ * in HS mode instead of SS mode. Workaround it by asserting -+ * LANE0.TX_ALT_BLOCK.EN_ALT_BUS to enable TX to use alt bus mode -+ */ -+ ret = qcom_dwc3_ss_read_phycreg(phy_dwc3->base, 0x102D, &data); -+ if (ret) -+ goto err_phy_trans; -+ -+ data |= (1 << 7); -+ ret = qcom_dwc3_ss_write_phycreg(phy_dwc3, 0x102D, data); -+ if (ret) -+ goto err_phy_trans; -+ -+ ret = qcom_dwc3_ss_read_phycreg(phy_dwc3->base, 0x1010, &data); -+ if (ret) -+ goto err_phy_trans; -+ -+ data &= ~0xff0; -+ data |= 0x20; -+ ret = qcom_dwc3_ss_write_phycreg(phy_dwc3, 0x1010, data); -+ if (ret) -+ goto err_phy_trans; -+ -+ /* -+ * Fix RX Equalization setting as follows -+ * LANE0.RX_OVRD_IN_HI. RX_EQ_EN set to 0 -+ * LANE0.RX_OVRD_IN_HI.RX_EQ_EN_OVRD set to 1 -+ * LANE0.RX_OVRD_IN_HI.RX_EQ set based on SoC version -+ * LANE0.RX_OVRD_IN_HI.RX_EQ_OVRD set to 1 -+ */ -+ ret = qcom_dwc3_ss_read_phycreg(phy_dwc3->base, -+ SSPHY_CTRL_RX_OVRD_IN_HI(0), &data); -+ if (ret) -+ goto err_phy_trans; -+ -+ data &= ~RX_OVRD_IN_HI_RX_EQ_EN; -+ data |= RX_OVRD_IN_HI_RX_EQ_EN_OVRD; -+ data &= ~RX_OVRD_IN_HI_RX_EQ_MASK; -+ data |= phy_dwc3->rx_eq << RX_OVRD_IN_HI_RX_EQ_SHIFT; -+ data |= RX_OVRD_IN_HI_RX_EQ_OVRD; -+ ret = qcom_dwc3_ss_write_phycreg(phy_dwc3, -+ SSPHY_CTRL_RX_OVRD_IN_HI(0), data); -+ if (ret) -+ goto err_phy_trans; -+ -+ /* -+ * Set EQ and TX launch amplitudes as follows -+ * LANE0.TX_OVRD_DRV_LO.PREEMPH set based on SoC version -+ * LANE0.TX_OVRD_DRV_LO.AMPLITUDE set to 110 -+ * LANE0.TX_OVRD_DRV_LO.EN set to 1. -+ */ -+ ret = qcom_dwc3_ss_read_phycreg(phy_dwc3->base, -+ SSPHY_CTRL_TX_OVRD_DRV_LO(0), &data); -+ if (ret) -+ goto err_phy_trans; -+ -+ data &= ~TX_OVRD_DRV_LO_PREEMPH_MASK; -+ data |= phy_dwc3->tx_deamp_3_5db << TX_OVRD_DRV_LO_PREEMPH_SHIFT; -+ data &= ~TX_OVRD_DRV_LO_AMPLITUDE_MASK; -+ data |= 0x6E; -+ data |= TX_OVRD_DRV_LO_EN; -+ ret = qcom_dwc3_ss_write_phycreg(phy_dwc3, -+ SSPHY_CTRL_TX_OVRD_DRV_LO(0), data); -+ if (ret) -+ goto err_phy_trans; -+ -+ qcom_dwc3_ss_write_phycreg(phy_dwc3, 0x30, phy_dwc3->mpll); -+ -+ /* -+ * Set the QSCRATCH PHY_PARAM_CTRL1 parameters as follows -+ * TX_FULL_SWING [26:20] amplitude to 110 -+ * TX_DEEMPH_6DB [19:14] to 32 -+ * TX_DEEMPH_3_5DB [13:8] set based on SoC version -+ * LOS_BIAS [7:3] to 9 -+ */ -+ regmap_read(phy_dwc3->base, SSUSB_PHY_PARAM_CTRL_1, &data); -+ -+ data &= ~PHY_PARAM_CTRL1_MASK; -+ -+ data |= PHY_PARAM_CTRL1_TX_FULL_SWING(0x6e) | -+ PHY_PARAM_CTRL1_TX_DEEMPH_6DB(0x20) | -+ PHY_PARAM_CTRL1_TX_DEEMPH_3_5DB(phy_dwc3->tx_deamp_3_5db) | -+ PHY_PARAM_CTRL1_LOS_BIAS(0x9); -+ -+ qcom_dwc3_phy_write_readback(phy_dwc3, SSUSB_PHY_PARAM_CTRL_1, -+ PHY_PARAM_CTRL1_MASK, data); -+ -+err_phy_trans: -+ return ret; -+} -+ -+static int qcom_dwc3_ss_phy_exit(struct phy *phy) -+{ -+ struct qcom_dwc3_usb_phy *phy_dwc3 = phy_get_drvdata(phy); -+ -+ /* Sequence to put SSPHY in low power state: -+ * 1. Clear REF_PHY_EN in PHY_CTRL_REG -+ * 2. Clear REF_USE_PAD in PHY_CTRL_REG -+ * 3. Set TEST_POWERED_DOWN in PHY_CTRL_REG to enable PHY retention -+ */ -+ qcom_dwc3_phy_write_readback(phy_dwc3, SSUSB_PHY_CTRL_REG, -+ SSUSB_CTRL_SS_PHY_EN, 0x0); -+ qcom_dwc3_phy_write_readback(phy_dwc3, SSUSB_PHY_CTRL_REG, -+ SSUSB_CTRL_REF_USE_PAD, 0x0); -+ qcom_dwc3_phy_write_readback(phy_dwc3, SSUSB_PHY_CTRL_REG, -+ SSUSB_CTRL_TEST_POWERDOWN, 0x0); -+ -+ clk_disable_unprepare(phy_dwc3->ref_clk); -+ clk_disable_unprepare(phy_dwc3->xo_clk); -+ -+ return 0; -+} -+ -+static const struct qcom_dwc3_phy_drvdata qcom_dwc3_hs_drvdata = { -+ .ops = { -+ .init = qcom_dwc3_hs_phy_init, -+ .exit = qcom_dwc3_hs_phy_exit, -+ .owner = THIS_MODULE, -+ }, -+ .clk_rate = 60000000, -+}; -+ -+static const struct qcom_dwc3_phy_drvdata qcom_dwc3_ss_drvdata = { -+ .ops = { -+ .init = qcom_dwc3_ss_phy_init, -+ .exit = qcom_dwc3_ss_phy_exit, -+ .owner = THIS_MODULE, -+ }, -+ .clk_rate = 125000000, -+}; -+ -+static const struct of_device_id qcom_dwc3_phy_table[] = { -+ { .compatible = "qcom,dwc3-hs-usb-phy", .data = &qcom_dwc3_hs_drvdata }, -+ { .compatible = "qcom,dwc3-ss-usb-phy", .data = &qcom_dwc3_ss_drvdata }, -+ { /* Sentinel */ } -+}; -+MODULE_DEVICE_TABLE(of, qcom_dwc3_phy_table); -+ -+static int qcom_dwc3_phy_probe(struct platform_device *pdev) -+{ -+ struct qcom_dwc3_usb_phy *phy_dwc3; -+ struct phy_provider *phy_provider; -+ struct phy *generic_phy; -+ struct resource *res; -+ const struct of_device_id *match; -+ const struct qcom_dwc3_phy_drvdata *data; -+ struct device_node *np; -+ -+ phy_dwc3 = devm_kzalloc(&pdev->dev, sizeof(*phy_dwc3), GFP_KERNEL); -+ if (!phy_dwc3) -+ return -ENOMEM; -+ -+ match = of_match_node(qcom_dwc3_phy_table, pdev->dev.of_node); -+ data = match->data; -+ -+ phy_dwc3->dev = &pdev->dev; -+ -+ phy_dwc3->base = syscon_regmap_lookup_by_phandle(pdev->dev.of_node, "regmap"); -+ if (IS_ERR_OR_NULL(phy_dwc3->base)) -+ return PTR_ERR_OR_ZERO(phy_dwc3->base) ? : -EINVAL; -+ -+ phy_dwc3->ref_clk = devm_clk_get(phy_dwc3->dev, "ref"); -+ if (IS_ERR(phy_dwc3->ref_clk)) { -+ dev_dbg(phy_dwc3->dev, "cannot get reference clock\n"); -+ return PTR_ERR(phy_dwc3->ref_clk); -+ } -+ -+ clk_set_rate(phy_dwc3->ref_clk, data->clk_rate); -+ -+ phy_dwc3->xo_clk = devm_clk_get(phy_dwc3->dev, "xo"); -+ if (IS_ERR(phy_dwc3->xo_clk)) { -+ dev_dbg(phy_dwc3->dev, "cannot get TCXO clock\n"); -+ phy_dwc3->xo_clk = NULL; -+ } -+ -+ /* Parse device node to probe HSIO settings */ -+ np = of_node_get(pdev->dev.of_node); -+ if (!of_compat_cmp(match->compatible, "qcom,dwc3-ss-usb-phy", -+ strlen(match->compatible))) { -+ -+ if (of_property_read_u32(np, "rx_eq", &phy_dwc3->rx_eq) || -+ of_property_read_u32(np, "tx_deamp_3_5db", -+ &phy_dwc3->tx_deamp_3_5db) || -+ of_property_read_u32(np, "mpll", &phy_dwc3->mpll)) { -+ -+ dev_err(phy_dwc3->dev, "cannot get HSIO settings from device node, using default values\n"); -+ -+ /* Default HSIO settings */ -+ phy_dwc3->rx_eq = SSPHY_RX_EQ_VALUE; -+ phy_dwc3->tx_deamp_3_5db = SSPHY_TX_DEEMPH_3_5DB; -+ phy_dwc3->mpll = SSPHY_MPLL_VALUE; -+ } -+ } -+ -+ generic_phy = devm_phy_create(phy_dwc3->dev, pdev->dev.of_node, -+ &data->ops); -+ -+ if (IS_ERR(generic_phy)) -+ return PTR_ERR(generic_phy); -+ -+ phy_set_drvdata(generic_phy, phy_dwc3); -+ platform_set_drvdata(pdev, phy_dwc3); -+ -+ phy_provider = devm_of_phy_provider_register(phy_dwc3->dev, -+ of_phy_simple_xlate); -+ -+ if (IS_ERR(phy_provider)) -+ return PTR_ERR(phy_provider); -+ -+ return 0; -+} -+ -+static struct platform_driver qcom_dwc3_phy_driver = { -+ .probe = qcom_dwc3_phy_probe, -+ .driver = { -+ .name = "qcom-dwc3-usb-phy", -+ .owner = THIS_MODULE, -+ .of_match_table = qcom_dwc3_phy_table, -+ }, -+}; -+ -+module_platform_driver(qcom_dwc3_phy_driver); -+ -+MODULE_ALIAS("platform:phy-qcom-dwc3"); -+MODULE_LICENSE("GPL v2"); -+MODULE_AUTHOR("Andy Gross "); -+MODULE_AUTHOR("Ivan T. Ivanov "); -+MODULE_DESCRIPTION("DesignWare USB3 QCOM PHY driver"); diff --git a/target/linux/ipq806x/patches-4.19/0033-ARM-qcom-automatically-select-PCI_DOMAINS-if-PCI-is-.patch b/target/linux/ipq806x/patches-4.19/0033-ARM-qcom-automatically-select-PCI_DOMAINS-if-PCI-is-.patch deleted file mode 100644 index a6c7953aaa..0000000000 --- a/target/linux/ipq806x/patches-4.19/0033-ARM-qcom-automatically-select-PCI_DOMAINS-if-PCI-is-.patch +++ /dev/null @@ -1,29 +0,0 @@ -From 48051ece78136e4235a2415a52797db56f8a4478 Mon Sep 17 00:00:00 2001 -From: Mathieu Olivari -Date: Tue, 21 Apr 2015 19:09:07 -0700 -Subject: [PATCH 33/69] ARM: qcom: automatically select PCI_DOMAINS if PCI is - enabled - -If multiple PCIe devices are present in the system, the kernel will -panic at boot time when trying to scan the PCI buses. This happens on -IPQ806x based platforms, which has 3 PCIe ports. - -Enabling this option allows the kernel to assign the pci-domains -according to the device-tree content. This allows multiple PCIe -controllers to coexist in the system. - -Signed-off-by: Mathieu Olivari ---- - arch/arm/mach-qcom/Kconfig | 1 + - 1 file changed, 1 insertion(+) - ---- a/arch/arm/mach-qcom/Kconfig -+++ b/arch/arm/mach-qcom/Kconfig -@@ -6,6 +6,7 @@ menuconfig ARCH_QCOM - select ARM_AMBA - select PINCTRL - select QCOM_SCM if SMP -+ select PCI_DOMAINS if PCI - help - Support for Qualcomm's devicetree based systems. - diff --git a/target/linux/ipq806x/patches-4.19/0034-0001-ARM-Add-Krait-L2-register-accessor-functions.patch b/target/linux/ipq806x/patches-4.19/0034-0001-ARM-Add-Krait-L2-register-accessor-functions.patch deleted file mode 100644 index 68acbeeec2..0000000000 --- a/target/linux/ipq806x/patches-4.19/0034-0001-ARM-Add-Krait-L2-register-accessor-functions.patch +++ /dev/null @@ -1,115 +0,0 @@ -From 36d68f64c411e09788687d5919886aadeb92adca Mon Sep 17 00:00:00 2001 -From: Stephen Boyd -Date: Tue, 14 Aug 2018 17:42:20 +0530 -Subject: [PATCH 01/12] ARM: Add Krait L2 register accessor functions - -Krait CPUs have a handful of L2 cache controller registers that -live behind a cp15 based indirection register. First you program -the indirection register (l2cpselr) to point the L2 'window' -register (l2cpdr) at what you want to read/write. Then you -read/write the 'window' register to do what you want. The -l2cpselr register is not banked per-cpu so we must lock around -accesses to it to prevent other CPUs from re-pointing l2cpdr -underneath us. - -Cc: Mark Rutland -Cc: Russell King -Acked-by: Bjorn Andersson -Signed-off-by: Stephen Boyd -Signed-off-by: Sricharan R -Tested-by: Craig Tatlor -Signed-off-by: Stephen Boyd ---- - arch/arm/common/Kconfig | 3 ++ - arch/arm/common/Makefile | 1 + - arch/arm/common/krait-l2-accessors.c | 48 +++++++++++++++++++++++ - arch/arm/include/asm/krait-l2-accessors.h | 9 +++++ - 4 files changed, 61 insertions(+) - create mode 100644 arch/arm/common/krait-l2-accessors.c - create mode 100644 arch/arm/include/asm/krait-l2-accessors.h - ---- a/arch/arm/common/Kconfig -+++ b/arch/arm/common/Kconfig -@@ -7,6 +7,9 @@ config DMABOUNCE - bool - select ZONE_DMA - -+config KRAIT_L2_ACCESSORS -+ bool -+ - config SHARP_LOCOMO - bool - ---- a/arch/arm/common/Makefile -+++ b/arch/arm/common/Makefile -@@ -7,6 +7,7 @@ obj-y += firmware.o - - obj-$(CONFIG_SA1111) += sa1111.o - obj-$(CONFIG_DMABOUNCE) += dmabounce.o -+obj-$(CONFIG_KRAIT_L2_ACCESSORS) += krait-l2-accessors.o - obj-$(CONFIG_SHARP_LOCOMO) += locomo.o - obj-$(CONFIG_SHARP_PARAM) += sharpsl_param.o - obj-$(CONFIG_SHARP_SCOOP) += scoop.o ---- /dev/null -+++ b/arch/arm/common/krait-l2-accessors.c -@@ -0,0 +1,48 @@ -+// SPDX-License-Identifier: GPL-2.0 -+// Copyright (c) 2018, The Linux Foundation. All rights reserved. -+ -+#include -+#include -+ -+#include -+#include -+ -+static DEFINE_RAW_SPINLOCK(krait_l2_lock); -+ -+void krait_set_l2_indirect_reg(u32 addr, u32 val) -+{ -+ unsigned long flags; -+ -+ raw_spin_lock_irqsave(&krait_l2_lock, flags); -+ /* -+ * Select the L2 window by poking l2cpselr, then write to the window -+ * via l2cpdr. -+ */ -+ asm volatile ("mcr p15, 3, %0, c15, c0, 6 @ l2cpselr" : : "r" (addr)); -+ isb(); -+ asm volatile ("mcr p15, 3, %0, c15, c0, 7 @ l2cpdr" : : "r" (val)); -+ isb(); -+ -+ raw_spin_unlock_irqrestore(&krait_l2_lock, flags); -+} -+EXPORT_SYMBOL(krait_set_l2_indirect_reg); -+ -+u32 krait_get_l2_indirect_reg(u32 addr) -+{ -+ u32 val; -+ unsigned long flags; -+ -+ raw_spin_lock_irqsave(&krait_l2_lock, flags); -+ /* -+ * Select the L2 window by poking l2cpselr, then read from the window -+ * via l2cpdr. -+ */ -+ asm volatile ("mcr p15, 3, %0, c15, c0, 6 @ l2cpselr" : : "r" (addr)); -+ isb(); -+ asm volatile ("mrc p15, 3, %0, c15, c0, 7 @ l2cpdr" : "=r" (val)); -+ -+ raw_spin_unlock_irqrestore(&krait_l2_lock, flags); -+ -+ return val; -+} -+EXPORT_SYMBOL(krait_get_l2_indirect_reg); ---- /dev/null -+++ b/arch/arm/include/asm/krait-l2-accessors.h -@@ -0,0 +1,9 @@ -+/* SPDX-License-Identifier: GPL-2.0 */ -+ -+#ifndef __ASMARM_KRAIT_L2_ACCESSORS_H -+#define __ASMARM_KRAIT_L2_ACCESSORS_H -+ -+extern void krait_set_l2_indirect_reg(u32 addr, u32 val); -+extern u32 krait_get_l2_indirect_reg(u32 addr); -+ -+#endif diff --git a/target/linux/ipq806x/patches-4.19/0034-0002-clk-qcom-Add-support-for-High-Frequency-PLLs-HFPLLs.patch b/target/linux/ipq806x/patches-4.19/0034-0002-clk-qcom-Add-support-for-High-Frequency-PLLs-HFPLLs.patch deleted file mode 100644 index d43d0c89b5..0000000000 --- a/target/linux/ipq806x/patches-4.19/0034-0002-clk-qcom-Add-support-for-High-Frequency-PLLs-HFPLLs.patch +++ /dev/null @@ -1,324 +0,0 @@ -From b3f2f10693aadeacf83ab5be03810941a4b77612 Mon Sep 17 00:00:00 2001 -From: Stephen Boyd -Date: Tue, 14 Aug 2018 17:42:21 +0530 -Subject: [PATCH 02/12] clk: qcom: Add support for High-Frequency PLLs (HFPLLs) - -HFPLLs are the main frequency source for Krait CPU clocks. Add -support for changing the rate of these PLLs. - -Signed-off-by: Stephen Boyd -Signed-off-by: Sricharan R -Tested-by: Craig Tatlor -Signed-off-by: Stephen Boyd ---- - drivers/clk/qcom/Makefile | 1 + - drivers/clk/qcom/clk-hfpll.c | 244 +++++++++++++++++++++++++++++++++++ - drivers/clk/qcom/clk-hfpll.h | 44 +++++++ - 3 files changed, 289 insertions(+) - create mode 100644 drivers/clk/qcom/clk-hfpll.c - create mode 100644 drivers/clk/qcom/clk-hfpll.h - ---- a/drivers/clk/qcom/Makefile -+++ b/drivers/clk/qcom/Makefile -@@ -11,6 +11,7 @@ clk-qcom-y += clk-branch.o - clk-qcom-y += clk-regmap-divider.o - clk-qcom-y += clk-regmap-mux.o - clk-qcom-y += clk-regmap-mux-div.o -+clk-qcom-y += clk-hfpll.o - clk-qcom-y += reset.o - clk-qcom-$(CONFIG_QCOM_GDSC) += gdsc.o - ---- /dev/null -+++ b/drivers/clk/qcom/clk-hfpll.c -@@ -0,0 +1,244 @@ -+// SPDX-License-Identifier: GPL-2.0 -+// Copyright (c) 2018, The Linux Foundation. All rights reserved. -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#include "clk-regmap.h" -+#include "clk-hfpll.h" -+ -+#define PLL_OUTCTRL BIT(0) -+#define PLL_BYPASSNL BIT(1) -+#define PLL_RESET_N BIT(2) -+ -+/* Initialize a HFPLL at a given rate and enable it. */ -+static void __clk_hfpll_init_once(struct clk_hw *hw) -+{ -+ struct clk_hfpll *h = to_clk_hfpll(hw); -+ struct hfpll_data const *hd = h->d; -+ struct regmap *regmap = h->clkr.regmap; -+ -+ if (likely(h->init_done)) -+ return; -+ -+ /* Configure PLL parameters for integer mode. */ -+ if (hd->config_val) -+ regmap_write(regmap, hd->config_reg, hd->config_val); -+ regmap_write(regmap, hd->m_reg, 0); -+ regmap_write(regmap, hd->n_reg, 1); -+ -+ if (hd->user_reg) { -+ u32 regval = hd->user_val; -+ unsigned long rate; -+ -+ rate = clk_hw_get_rate(hw); -+ -+ /* Pick the right VCO. */ -+ if (hd->user_vco_mask && rate > hd->low_vco_max_rate) -+ regval |= hd->user_vco_mask; -+ regmap_write(regmap, hd->user_reg, regval); -+ } -+ -+ if (hd->droop_reg) -+ regmap_write(regmap, hd->droop_reg, hd->droop_val); -+ -+ h->init_done = true; -+} -+ -+static void __clk_hfpll_enable(struct clk_hw *hw) -+{ -+ struct clk_hfpll *h = to_clk_hfpll(hw); -+ struct hfpll_data const *hd = h->d; -+ struct regmap *regmap = h->clkr.regmap; -+ u32 val; -+ -+ __clk_hfpll_init_once(hw); -+ -+ /* Disable PLL bypass mode. */ -+ regmap_update_bits(regmap, hd->mode_reg, PLL_BYPASSNL, PLL_BYPASSNL); -+ -+ /* -+ * H/W requires a 5us delay between disabling the bypass and -+ * de-asserting the reset. Delay 10us just to be safe. -+ */ -+ udelay(10); -+ -+ /* De-assert active-low PLL reset. */ -+ regmap_update_bits(regmap, hd->mode_reg, PLL_RESET_N, PLL_RESET_N); -+ -+ /* Wait for PLL to lock. */ -+ if (hd->status_reg) { -+ do { -+ regmap_read(regmap, hd->status_reg, &val); -+ } while (!(val & BIT(hd->lock_bit))); -+ } else { -+ udelay(60); -+ } -+ -+ /* Enable PLL output. */ -+ regmap_update_bits(regmap, hd->mode_reg, PLL_OUTCTRL, PLL_OUTCTRL); -+} -+ -+/* Enable an already-configured HFPLL. */ -+static int clk_hfpll_enable(struct clk_hw *hw) -+{ -+ unsigned long flags; -+ struct clk_hfpll *h = to_clk_hfpll(hw); -+ struct hfpll_data const *hd = h->d; -+ struct regmap *regmap = h->clkr.regmap; -+ u32 mode; -+ -+ spin_lock_irqsave(&h->lock, flags); -+ regmap_read(regmap, hd->mode_reg, &mode); -+ if (!(mode & (PLL_BYPASSNL | PLL_RESET_N | PLL_OUTCTRL))) -+ __clk_hfpll_enable(hw); -+ spin_unlock_irqrestore(&h->lock, flags); -+ -+ return 0; -+} -+ -+static void __clk_hfpll_disable(struct clk_hfpll *h) -+{ -+ struct hfpll_data const *hd = h->d; -+ struct regmap *regmap = h->clkr.regmap; -+ -+ /* -+ * Disable the PLL output, disable test mode, enable the bypass mode, -+ * and assert the reset. -+ */ -+ regmap_update_bits(regmap, hd->mode_reg, -+ PLL_BYPASSNL | PLL_RESET_N | PLL_OUTCTRL, 0); -+} -+ -+static void clk_hfpll_disable(struct clk_hw *hw) -+{ -+ struct clk_hfpll *h = to_clk_hfpll(hw); -+ unsigned long flags; -+ -+ spin_lock_irqsave(&h->lock, flags); -+ __clk_hfpll_disable(h); -+ spin_unlock_irqrestore(&h->lock, flags); -+} -+ -+static long clk_hfpll_round_rate(struct clk_hw *hw, unsigned long rate, -+ unsigned long *parent_rate) -+{ -+ struct clk_hfpll *h = to_clk_hfpll(hw); -+ struct hfpll_data const *hd = h->d; -+ unsigned long rrate; -+ -+ rate = clamp(rate, hd->min_rate, hd->max_rate); -+ -+ rrate = DIV_ROUND_UP(rate, *parent_rate) * *parent_rate; -+ if (rrate > hd->max_rate) -+ rrate -= *parent_rate; -+ -+ return rrate; -+} -+ -+/* -+ * For optimization reasons, assumes no downstream clocks are actively using -+ * it. -+ */ -+static int clk_hfpll_set_rate(struct clk_hw *hw, unsigned long rate, -+ unsigned long parent_rate) -+{ -+ struct clk_hfpll *h = to_clk_hfpll(hw); -+ struct hfpll_data const *hd = h->d; -+ struct regmap *regmap = h->clkr.regmap; -+ unsigned long flags; -+ u32 l_val, val; -+ bool enabled; -+ -+ l_val = rate / parent_rate; -+ -+ spin_lock_irqsave(&h->lock, flags); -+ -+ enabled = __clk_is_enabled(hw->clk); -+ if (enabled) -+ __clk_hfpll_disable(h); -+ -+ /* Pick the right VCO. */ -+ if (hd->user_reg && hd->user_vco_mask) { -+ regmap_read(regmap, hd->user_reg, &val); -+ if (rate <= hd->low_vco_max_rate) -+ val &= ~hd->user_vco_mask; -+ else -+ val |= hd->user_vco_mask; -+ regmap_write(regmap, hd->user_reg, val); -+ } -+ -+ regmap_write(regmap, hd->l_reg, l_val); -+ -+ if (enabled) -+ __clk_hfpll_enable(hw); -+ -+ spin_unlock_irqrestore(&h->lock, flags); -+ -+ return 0; -+} -+ -+static unsigned long clk_hfpll_recalc_rate(struct clk_hw *hw, -+ unsigned long parent_rate) -+{ -+ struct clk_hfpll *h = to_clk_hfpll(hw); -+ struct hfpll_data const *hd = h->d; -+ struct regmap *regmap = h->clkr.regmap; -+ u32 l_val; -+ -+ regmap_read(regmap, hd->l_reg, &l_val); -+ -+ return l_val * parent_rate; -+} -+ -+static void clk_hfpll_init(struct clk_hw *hw) -+{ -+ struct clk_hfpll *h = to_clk_hfpll(hw); -+ struct hfpll_data const *hd = h->d; -+ struct regmap *regmap = h->clkr.regmap; -+ u32 mode, status; -+ -+ regmap_read(regmap, hd->mode_reg, &mode); -+ if (mode != (PLL_BYPASSNL | PLL_RESET_N | PLL_OUTCTRL)) { -+ __clk_hfpll_init_once(hw); -+ return; -+ } -+ -+ if (hd->status_reg) { -+ regmap_read(regmap, hd->status_reg, &status); -+ if (!(status & BIT(hd->lock_bit))) { -+ WARN(1, "HFPLL %s is ON, but not locked!\n", -+ __clk_get_name(hw->clk)); -+ clk_hfpll_disable(hw); -+ __clk_hfpll_init_once(hw); -+ } -+ } -+} -+ -+static int hfpll_is_enabled(struct clk_hw *hw) -+{ -+ struct clk_hfpll *h = to_clk_hfpll(hw); -+ struct hfpll_data const *hd = h->d; -+ struct regmap *regmap = h->clkr.regmap; -+ u32 mode; -+ -+ regmap_read(regmap, hd->mode_reg, &mode); -+ mode &= 0x7; -+ return mode == (PLL_BYPASSNL | PLL_RESET_N | PLL_OUTCTRL); -+} -+ -+const struct clk_ops clk_ops_hfpll = { -+ .enable = clk_hfpll_enable, -+ .disable = clk_hfpll_disable, -+ .is_enabled = hfpll_is_enabled, -+ .round_rate = clk_hfpll_round_rate, -+ .set_rate = clk_hfpll_set_rate, -+ .recalc_rate = clk_hfpll_recalc_rate, -+ .init = clk_hfpll_init, -+}; -+EXPORT_SYMBOL_GPL(clk_ops_hfpll); ---- /dev/null -+++ b/drivers/clk/qcom/clk-hfpll.h -@@ -0,0 +1,44 @@ -+/* SPDX-License-Identifier: GPL-2.0 */ -+ -+#ifndef __QCOM_CLK_HFPLL_H__ -+#define __QCOM_CLK_HFPLL_H__ -+ -+#include -+#include -+#include "clk-regmap.h" -+ -+struct hfpll_data { -+ u32 mode_reg; -+ u32 l_reg; -+ u32 m_reg; -+ u32 n_reg; -+ u32 user_reg; -+ u32 droop_reg; -+ u32 config_reg; -+ u32 status_reg; -+ u8 lock_bit; -+ -+ u32 droop_val; -+ u32 config_val; -+ u32 user_val; -+ u32 user_vco_mask; -+ unsigned long low_vco_max_rate; -+ -+ unsigned long min_rate; -+ unsigned long max_rate; -+}; -+ -+struct clk_hfpll { -+ struct hfpll_data const *d; -+ int init_done; -+ -+ struct clk_regmap clkr; -+ spinlock_t lock; -+}; -+ -+#define to_clk_hfpll(_hw) \ -+ container_of(to_clk_regmap(_hw), struct clk_hfpll, clkr) -+ -+extern const struct clk_ops clk_ops_hfpll; -+ -+#endif diff --git a/target/linux/ipq806x/patches-4.19/0034-0003-clk-qcom-Add-HFPLL-driver.patch b/target/linux/ipq806x/patches-4.19/0034-0003-clk-qcom-Add-HFPLL-driver.patch deleted file mode 100644 index 292eb66d67..0000000000 --- a/target/linux/ipq806x/patches-4.19/0034-0003-clk-qcom-Add-HFPLL-driver.patch +++ /dev/null @@ -1,142 +0,0 @@ -From cb546b797a0da4dbb1a0c76a2a357921887b6189 Mon Sep 17 00:00:00 2001 -From: Stephen Boyd -Date: Tue, 14 Aug 2018 17:42:22 +0530 -Subject: [PATCH 03/12] clk: qcom: Add HFPLL driver - -On some devices (MSM8974 for example), the HFPLLs are -instantiated within the Krait processor subsystem as separate -register regions. Add a driver for these PLLs so that we can -provide HFPLL clocks for use by the system. - -Cc: -Signed-off-by: Stephen Boyd -Signed-off-by: Sricharan R -Tested-by: Craig Tatlor -Signed-off-by: Stephen Boyd ---- - drivers/clk/qcom/Kconfig | 8 ++++ - drivers/clk/qcom/Makefile | 1 + - drivers/clk/qcom/hfpll.c | 96 +++++++++++++++++++++++++++++++++++++++ - 3 files changed, 105 insertions(+) - create mode 100644 drivers/clk/qcom/hfpll.c - ---- a/drivers/clk/qcom/Kconfig -+++ b/drivers/clk/qcom/Kconfig -@@ -272,3 +272,11 @@ config SPMI_PMIC_CLKDIV - Technologies, Inc. SPMI PMIC. It configures the frequency of - clkdiv outputs of the PMIC. These clocks are typically wired - through alternate functions on GPIO pins. -+ -+config QCOM_HFPLL -+ tristate "High-Frequency PLL (HFPLL) Clock Controller" -+ depends on COMMON_CLK_QCOM -+ help -+ Support for the high-frequency PLLs present on Qualcomm devices. -+ Say Y if you want to support CPU frequency scaling on devices -+ such as MSM8974, APQ8084, etc. ---- a/drivers/clk/qcom/Makefile -+++ b/drivers/clk/qcom/Makefile -@@ -44,3 +44,4 @@ obj-$(CONFIG_SDM_DISPCC_845) += dispcc-s - obj-$(CONFIG_SDM_GCC_845) += gcc-sdm845.o - obj-$(CONFIG_SDM_VIDEOCC_845) += videocc-sdm845.o - obj-$(CONFIG_SPMI_PMIC_CLKDIV) += clk-spmi-pmic-div.o -+obj-$(CONFIG_QCOM_HFPLL) += hfpll.o ---- /dev/null -+++ b/drivers/clk/qcom/hfpll.c -@@ -0,0 +1,96 @@ -+// SPDX-License-Identifier: GPL-2.0 -+// Copyright (c) 2018, The Linux Foundation. All rights reserved. -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#include "clk-regmap.h" -+#include "clk-hfpll.h" -+ -+static const struct hfpll_data hdata = { -+ .mode_reg = 0x00, -+ .l_reg = 0x04, -+ .m_reg = 0x08, -+ .n_reg = 0x0c, -+ .user_reg = 0x10, -+ .config_reg = 0x14, -+ .config_val = 0x430405d, -+ .status_reg = 0x1c, -+ .lock_bit = 16, -+ -+ .user_val = 0x8, -+ .user_vco_mask = 0x100000, -+ .low_vco_max_rate = 1248000000, -+ .min_rate = 537600000UL, -+ .max_rate = 2900000000UL, -+}; -+ -+static const struct of_device_id qcom_hfpll_match_table[] = { -+ { .compatible = "qcom,hfpll" }, -+ { } -+}; -+MODULE_DEVICE_TABLE(of, qcom_hfpll_match_table); -+ -+static const struct regmap_config hfpll_regmap_config = { -+ .reg_bits = 32, -+ .reg_stride = 4, -+ .val_bits = 32, -+ .max_register = 0x30, -+ .fast_io = true, -+}; -+ -+static int qcom_hfpll_probe(struct platform_device *pdev) -+{ -+ struct resource *res; -+ struct device *dev = &pdev->dev; -+ void __iomem *base; -+ struct regmap *regmap; -+ struct clk_hfpll *h; -+ struct clk_init_data init = { -+ .parent_names = (const char *[]){ "xo" }, -+ .num_parents = 1, -+ .ops = &clk_ops_hfpll, -+ }; -+ -+ h = devm_kzalloc(dev, sizeof(*h), GFP_KERNEL); -+ if (!h) -+ return -ENOMEM; -+ -+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); -+ base = devm_ioremap_resource(dev, res); -+ if (IS_ERR(base)) -+ return PTR_ERR(base); -+ -+ regmap = devm_regmap_init_mmio(&pdev->dev, base, &hfpll_regmap_config); -+ if (IS_ERR(regmap)) -+ return PTR_ERR(regmap); -+ -+ if (of_property_read_string_index(dev->of_node, "clock-output-names", -+ 0, &init.name)) -+ return -ENODEV; -+ -+ h->d = &hdata; -+ h->clkr.hw.init = &init; -+ spin_lock_init(&h->lock); -+ -+ return devm_clk_register_regmap(&pdev->dev, &h->clkr); -+} -+ -+static struct platform_driver qcom_hfpll_driver = { -+ .probe = qcom_hfpll_probe, -+ .driver = { -+ .name = "qcom-hfpll", -+ .of_match_table = qcom_hfpll_match_table, -+ }, -+}; -+module_platform_driver(qcom_hfpll_driver); -+ -+MODULE_DESCRIPTION("QCOM HFPLL Clock Driver"); -+MODULE_LICENSE("GPL v2"); -+MODULE_ALIAS("platform:qcom-hfpll"); diff --git a/target/linux/ipq806x/patches-4.19/0034-0004-dt-bindings-clock-Document-qcom-hfpll.patch b/target/linux/ipq806x/patches-4.19/0034-0004-dt-bindings-clock-Document-qcom-hfpll.patch deleted file mode 100644 index 1db989f6d9..0000000000 --- a/target/linux/ipq806x/patches-4.19/0034-0004-dt-bindings-clock-Document-qcom-hfpll.patch +++ /dev/null @@ -1,81 +0,0 @@ -From 1f924faa8b1e4789ecc06ed0dd58ca3487c89012 Mon Sep 17 00:00:00 2001 -From: Stephen Boyd -Date: Tue, 14 Aug 2018 17:42:23 +0530 -Subject: [PATCH 04/12] dt-bindings: clock: Document qcom,hfpll - -Adds bindings document for qcom,hfpll instantiated within -the Krait processor subsystem as separate register region. - -Reviewed-by: Rob Herring -Signed-off-by: Stephen Boyd -Signed-off-by: Sricharan R -Tested-by: Craig Tatlor -Signed-off-by: Stephen Boyd ---- - .../devicetree/bindings/clock/qcom,hfpll.txt | 60 +++++++++++++++++++ - 1 file changed, 60 insertions(+) - create mode 100644 Documentation/devicetree/bindings/clock/qcom,hfpll.txt - ---- /dev/null -+++ b/Documentation/devicetree/bindings/clock/qcom,hfpll.txt -@@ -0,0 +1,60 @@ -+High-Frequency PLL (HFPLL) -+ -+PROPERTIES -+ -+- compatible: -+ Usage: required -+ Value type: : -+ shall contain only one of the following. The generic -+ compatible "qcom,hfpll" should be also included. -+ -+ "qcom,hfpll-ipq8064", "qcom,hfpll" -+ "qcom,hfpll-apq8064", "qcom,hfpll" -+ "qcom,hfpll-msm8974", "qcom,hfpll" -+ "qcom,hfpll-msm8960", "qcom,hfpll" -+ -+- reg: -+ Usage: required -+ Value type: -+ Definition: address and size of HPLL registers. An optional second -+ element specifies the address and size of the alias -+ register region. -+ -+- clocks: -+ Usage: required -+ Value type: -+ Definition: reference to the xo clock. -+ -+- clock-names: -+ Usage: required -+ Value type: -+ Definition: must be "xo". -+ -+- clock-output-names: -+ Usage: required -+ Value type: -+ Definition: Name of the PLL. Typically hfpllX where X is a CPU number -+ starting at 0. Otherwise hfpll_Y where Y is more specific -+ such as "l2". -+ -+Example: -+ -+1) An HFPLL for the L2 cache. -+ -+ clock-controller@f9016000 { -+ compatible = "qcom,hfpll-ipq8064", "qcom,hfpll"; -+ reg = <0xf9016000 0x30>; -+ clocks = <&xo_board>; -+ clock-names = "xo"; -+ clock-output-names = "hfpll_l2"; -+ }; -+ -+2) An HFPLL for CPU0. This HFPLL has the alias register region. -+ -+ clock-controller@f908a000 { -+ compatible = "qcom,hfpll-ipq8064", "qcom,hfpll"; -+ reg = <0xf908a000 0x30>, <0xf900a000 0x30>; -+ clocks = <&xo_board>; -+ clock-names = "xo"; -+ clock-output-names = "hfpll0"; -+ }; diff --git a/target/linux/ipq806x/patches-4.19/0034-0005-clk-qcom-Add-MSM8960-APQ8064-s-HFPLLs.patch b/target/linux/ipq806x/patches-4.19/0034-0005-clk-qcom-Add-MSM8960-APQ8064-s-HFPLLs.patch deleted file mode 100644 index 5ed5625f2e..0000000000 --- a/target/linux/ipq806x/patches-4.19/0034-0005-clk-qcom-Add-MSM8960-APQ8064-s-HFPLLs.patch +++ /dev/null @@ -1,236 +0,0 @@ -From 72ad7207954dd622a662ba884dc6c30a820123f2 Mon Sep 17 00:00:00 2001 -From: Stephen Boyd -Date: Tue, 14 Aug 2018 17:42:24 +0530 -Subject: [PATCH 05/12] clk: qcom: Add MSM8960/APQ8064's HFPLLs - -Describe the HFPLLs present on MSM8960 and APQ8064 devices. - -Acked-by: Rob Herring (bindings) -Signed-off-by: Stephen Boyd -Signed-off-by: Sricharan R -Tested-by: Craig Tatlor -Signed-off-by: Stephen Boyd ---- - drivers/clk/qcom/gcc-msm8960.c | 172 +++++++++++++++++++ - include/dt-bindings/clock/qcom,gcc-msm8960.h | 2 + - 2 files changed, 174 insertions(+) - ---- a/drivers/clk/qcom/gcc-msm8960.c -+++ b/drivers/clk/qcom/gcc-msm8960.c -@@ -30,6 +30,7 @@ - #include "clk-pll.h" - #include "clk-rcg.h" - #include "clk-branch.h" -+#include "clk-hfpll.h" - #include "reset.h" - - static struct clk_pll pll3 = { -@@ -86,6 +87,164 @@ static struct clk_regmap pll8_vote = { - }, - }; - -+static struct hfpll_data hfpll0_data = { -+ .mode_reg = 0x3200, -+ .l_reg = 0x3208, -+ .m_reg = 0x320c, -+ .n_reg = 0x3210, -+ .config_reg = 0x3204, -+ .status_reg = 0x321c, -+ .config_val = 0x7845c665, -+ .droop_reg = 0x3214, -+ .droop_val = 0x0108c000, -+ .min_rate = 600000000UL, -+ .max_rate = 1800000000UL, -+}; -+ -+static struct clk_hfpll hfpll0 = { -+ .d = &hfpll0_data, -+ .clkr.hw.init = &(struct clk_init_data){ -+ .parent_names = (const char *[]){ "pxo" }, -+ .num_parents = 1, -+ .name = "hfpll0", -+ .ops = &clk_ops_hfpll, -+ .flags = CLK_IGNORE_UNUSED, -+ }, -+ .lock = __SPIN_LOCK_UNLOCKED(hfpll0.lock), -+}; -+ -+static struct hfpll_data hfpll1_8064_data = { -+ .mode_reg = 0x3240, -+ .l_reg = 0x3248, -+ .m_reg = 0x324c, -+ .n_reg = 0x3250, -+ .config_reg = 0x3244, -+ .status_reg = 0x325c, -+ .config_val = 0x7845c665, -+ .droop_reg = 0x3254, -+ .droop_val = 0x0108c000, -+ .min_rate = 600000000UL, -+ .max_rate = 1800000000UL, -+}; -+ -+static struct hfpll_data hfpll1_data = { -+ .mode_reg = 0x3300, -+ .l_reg = 0x3308, -+ .m_reg = 0x330c, -+ .n_reg = 0x3310, -+ .config_reg = 0x3304, -+ .status_reg = 0x331c, -+ .config_val = 0x7845c665, -+ .droop_reg = 0x3314, -+ .droop_val = 0x0108c000, -+ .min_rate = 600000000UL, -+ .max_rate = 1800000000UL, -+}; -+ -+static struct clk_hfpll hfpll1 = { -+ .d = &hfpll1_data, -+ .clkr.hw.init = &(struct clk_init_data){ -+ .parent_names = (const char *[]){ "pxo" }, -+ .num_parents = 1, -+ .name = "hfpll1", -+ .ops = &clk_ops_hfpll, -+ .flags = CLK_IGNORE_UNUSED, -+ }, -+ .lock = __SPIN_LOCK_UNLOCKED(hfpll1.lock), -+}; -+ -+static struct hfpll_data hfpll2_data = { -+ .mode_reg = 0x3280, -+ .l_reg = 0x3288, -+ .m_reg = 0x328c, -+ .n_reg = 0x3290, -+ .config_reg = 0x3284, -+ .status_reg = 0x329c, -+ .config_val = 0x7845c665, -+ .droop_reg = 0x3294, -+ .droop_val = 0x0108c000, -+ .min_rate = 600000000UL, -+ .max_rate = 1800000000UL, -+}; -+ -+static struct clk_hfpll hfpll2 = { -+ .d = &hfpll2_data, -+ .clkr.hw.init = &(struct clk_init_data){ -+ .parent_names = (const char *[]){ "pxo" }, -+ .num_parents = 1, -+ .name = "hfpll2", -+ .ops = &clk_ops_hfpll, -+ .flags = CLK_IGNORE_UNUSED, -+ }, -+ .lock = __SPIN_LOCK_UNLOCKED(hfpll2.lock), -+}; -+ -+static struct hfpll_data hfpll3_data = { -+ .mode_reg = 0x32c0, -+ .l_reg = 0x32c8, -+ .m_reg = 0x32cc, -+ .n_reg = 0x32d0, -+ .config_reg = 0x32c4, -+ .status_reg = 0x32dc, -+ .config_val = 0x7845c665, -+ .droop_reg = 0x32d4, -+ .droop_val = 0x0108c000, -+ .min_rate = 600000000UL, -+ .max_rate = 1800000000UL, -+}; -+ -+static struct clk_hfpll hfpll3 = { -+ .d = &hfpll3_data, -+ .clkr.hw.init = &(struct clk_init_data){ -+ .parent_names = (const char *[]){ "pxo" }, -+ .num_parents = 1, -+ .name = "hfpll3", -+ .ops = &clk_ops_hfpll, -+ .flags = CLK_IGNORE_UNUSED, -+ }, -+ .lock = __SPIN_LOCK_UNLOCKED(hfpll3.lock), -+}; -+ -+static struct hfpll_data hfpll_l2_8064_data = { -+ .mode_reg = 0x3300, -+ .l_reg = 0x3308, -+ .m_reg = 0x330c, -+ .n_reg = 0x3310, -+ .config_reg = 0x3304, -+ .status_reg = 0x331c, -+ .config_val = 0x7845c665, -+ .droop_reg = 0x3314, -+ .droop_val = 0x0108c000, -+ .min_rate = 600000000UL, -+ .max_rate = 1800000000UL, -+}; -+ -+static struct hfpll_data hfpll_l2_data = { -+ .mode_reg = 0x3400, -+ .l_reg = 0x3408, -+ .m_reg = 0x340c, -+ .n_reg = 0x3410, -+ .config_reg = 0x3404, -+ .status_reg = 0x341c, -+ .config_val = 0x7845c665, -+ .droop_reg = 0x3414, -+ .droop_val = 0x0108c000, -+ .min_rate = 600000000UL, -+ .max_rate = 1800000000UL, -+}; -+ -+static struct clk_hfpll hfpll_l2 = { -+ .d = &hfpll_l2_data, -+ .clkr.hw.init = &(struct clk_init_data){ -+ .parent_names = (const char *[]){ "pxo" }, -+ .num_parents = 1, -+ .name = "hfpll_l2", -+ .ops = &clk_ops_hfpll, -+ .flags = CLK_IGNORE_UNUSED, -+ }, -+ .lock = __SPIN_LOCK_UNLOCKED(hfpll_l2.lock), -+}; -+ - static struct clk_pll pll14 = { - .l_reg = 0x31c4, - .m_reg = 0x31c8, -@@ -3107,6 +3266,9 @@ static struct clk_regmap *gcc_msm8960_cl - [PMIC_ARB1_H_CLK] = &pmic_arb1_h_clk.clkr, - [PMIC_SSBI2_CLK] = &pmic_ssbi2_clk.clkr, - [RPM_MSG_RAM_H_CLK] = &rpm_msg_ram_h_clk.clkr, -+ [PLL9] = &hfpll0.clkr, -+ [PLL10] = &hfpll1.clkr, -+ [PLL12] = &hfpll_l2.clkr, - }; - - static const struct qcom_reset_map gcc_msm8960_resets[] = { -@@ -3318,6 +3480,11 @@ static struct clk_regmap *gcc_apq8064_cl - [PMIC_ARB1_H_CLK] = &pmic_arb1_h_clk.clkr, - [PMIC_SSBI2_CLK] = &pmic_ssbi2_clk.clkr, - [RPM_MSG_RAM_H_CLK] = &rpm_msg_ram_h_clk.clkr, -+ [PLL9] = &hfpll0.clkr, -+ [PLL10] = &hfpll1.clkr, -+ [PLL12] = &hfpll_l2.clkr, -+ [PLL16] = &hfpll2.clkr, -+ [PLL17] = &hfpll3.clkr, - }; - - static const struct qcom_reset_map gcc_apq8064_resets[] = { -@@ -3477,6 +3644,11 @@ static int gcc_msm8960_probe(struct plat - if (ret) - return ret; - -+ if (match->data == &gcc_apq8064_desc) { -+ hfpll1.d = &hfpll1_8064_data; -+ hfpll_l2.d = &hfpll_l2_8064_data; -+ } -+ - tsens = platform_device_register_data(&pdev->dev, "qcom-tsens", -1, - NULL, 0); - if (IS_ERR(tsens)) ---- a/include/dt-bindings/clock/qcom,gcc-msm8960.h -+++ b/include/dt-bindings/clock/qcom,gcc-msm8960.h -@@ -319,5 +319,7 @@ - #define CE3_SRC 303 - #define CE3_CORE_CLK 304 - #define CE3_H_CLK 305 -+#define PLL16 306 -+#define PLL17 307 - - #endif diff --git a/target/linux/ipq806x/patches-4.19/0034-0006-clk-qcom-Add-IPQ806X-s-HFPLLs.patch b/target/linux/ipq806x/patches-4.19/0034-0006-clk-qcom-Add-IPQ806X-s-HFPLLs.patch deleted file mode 100644 index 74c66178a8..0000000000 --- a/target/linux/ipq806x/patches-4.19/0034-0006-clk-qcom-Add-IPQ806X-s-HFPLLs.patch +++ /dev/null @@ -1,120 +0,0 @@ -From 1f79131bfd512f322c16b58dca581ce39beafab9 Mon Sep 17 00:00:00 2001 -From: Stephen Boyd -Date: Tue, 14 Aug 2018 17:42:25 +0530 -Subject: [PATCH 06/12] clk: qcom: Add IPQ806X's HFPLLs - -Describe the HFPLLs present on IPQ806X devices. - -Signed-off-by: Stephen Boyd -Signed-off-by: Sricharan R -Tested-by: Craig Tatlor -Signed-off-by: Stephen Boyd ---- - drivers/clk/qcom/gcc-ipq806x.c | 82 ++++++++++++++++++++++++++++++++++ - 1 file changed, 82 insertions(+) - ---- a/drivers/clk/qcom/gcc-ipq806x.c -+++ b/drivers/clk/qcom/gcc-ipq806x.c -@@ -30,6 +30,7 @@ - #include "clk-pll.h" - #include "clk-rcg.h" - #include "clk-branch.h" -+#include "clk-hfpll.h" - #include "reset.h" - - static struct clk_pll pll0 = { -@@ -113,6 +114,84 @@ static struct clk_regmap pll8_vote = { - }, - }; - -+static struct hfpll_data hfpll0_data = { -+ .mode_reg = 0x3200, -+ .l_reg = 0x3208, -+ .m_reg = 0x320c, -+ .n_reg = 0x3210, -+ .config_reg = 0x3204, -+ .status_reg = 0x321c, -+ .config_val = 0x7845c665, -+ .droop_reg = 0x3214, -+ .droop_val = 0x0108c000, -+ .min_rate = 600000000UL, -+ .max_rate = 1800000000UL, -+}; -+ -+static struct clk_hfpll hfpll0 = { -+ .d = &hfpll0_data, -+ .clkr.hw.init = &(struct clk_init_data){ -+ .parent_names = (const char *[]){ "pxo" }, -+ .num_parents = 1, -+ .name = "hfpll0", -+ .ops = &clk_ops_hfpll, -+ .flags = CLK_IGNORE_UNUSED, -+ }, -+ .lock = __SPIN_LOCK_UNLOCKED(hfpll0.lock), -+}; -+ -+static struct hfpll_data hfpll1_data = { -+ .mode_reg = 0x3240, -+ .l_reg = 0x3248, -+ .m_reg = 0x324c, -+ .n_reg = 0x3250, -+ .config_reg = 0x3244, -+ .status_reg = 0x325c, -+ .config_val = 0x7845c665, -+ .droop_reg = 0x3314, -+ .droop_val = 0x0108c000, -+ .min_rate = 600000000UL, -+ .max_rate = 1800000000UL, -+}; -+ -+static struct clk_hfpll hfpll1 = { -+ .d = &hfpll1_data, -+ .clkr.hw.init = &(struct clk_init_data){ -+ .parent_names = (const char *[]){ "pxo" }, -+ .num_parents = 1, -+ .name = "hfpll1", -+ .ops = &clk_ops_hfpll, -+ .flags = CLK_IGNORE_UNUSED, -+ }, -+ .lock = __SPIN_LOCK_UNLOCKED(hfpll1.lock), -+}; -+ -+static struct hfpll_data hfpll_l2_data = { -+ .mode_reg = 0x3300, -+ .l_reg = 0x3308, -+ .m_reg = 0x330c, -+ .n_reg = 0x3310, -+ .config_reg = 0x3304, -+ .status_reg = 0x331c, -+ .config_val = 0x7845c665, -+ .droop_reg = 0x3314, -+ .droop_val = 0x0108c000, -+ .min_rate = 600000000UL, -+ .max_rate = 1800000000UL, -+}; -+ -+static struct clk_hfpll hfpll_l2 = { -+ .d = &hfpll_l2_data, -+ .clkr.hw.init = &(struct clk_init_data){ -+ .parent_names = (const char *[]){ "pxo" }, -+ .num_parents = 1, -+ .name = "hfpll_l2", -+ .ops = &clk_ops_hfpll, -+ .flags = CLK_IGNORE_UNUSED, -+ }, -+ .lock = __SPIN_LOCK_UNLOCKED(hfpll_l2.lock), -+}; -+ - static struct clk_pll pll14 = { - .l_reg = 0x31c4, - .m_reg = 0x31c8, -@@ -2798,6 +2877,9 @@ static struct clk_regmap *gcc_ipq806x_cl - [UBI32_CORE2_CLK_SRC] = &ubi32_core2_src_clk.clkr, - [NSSTCM_CLK_SRC] = &nss_tcm_src.clkr, - [NSSTCM_CLK] = &nss_tcm_clk.clkr, -+ [PLL9] = &hfpll0.clkr, -+ [PLL10] = &hfpll1.clkr, -+ [PLL12] = &hfpll_l2.clkr, - }; - - static const struct qcom_reset_map gcc_ipq806x_resets[] = { diff --git a/target/linux/ipq806x/patches-4.19/0034-0007-clk-qcom-Add-support-for-Krait-clocks.patch b/target/linux/ipq806x/patches-4.19/0034-0007-clk-qcom-Add-support-for-Krait-clocks.patch deleted file mode 100644 index 181b91f6eb..0000000000 --- a/target/linux/ipq806x/patches-4.19/0034-0007-clk-qcom-Add-support-for-Krait-clocks.patch +++ /dev/null @@ -1,213 +0,0 @@ -From 4d7dc77babfef1d6cb8fd825e2f17dc3384c3272 Mon Sep 17 00:00:00 2001 -From: Stephen Boyd -Date: Tue, 14 Aug 2018 17:42:26 +0530 -Subject: [PATCH 07/12] clk: qcom: Add support for Krait clocks - -The Krait clocks are made up of a series of muxes and a divider -that choose between a fixed rate clock and dedicated HFPLLs for -each CPU. Instead of using mmio accesses to remux parents, the -Krait implementation exposes the remux control via cp15 -registers. Support these clocks. - -Signed-off-by: Stephen Boyd -Signed-off-by: Sricharan R -Tested-by: Craig Tatlor -[sboyd@kernel.org: Move hidden config to top outside of the visible qcom -config zone so that menuconfig looks nice] -Signed-off-by: Stephen Boyd ---- - drivers/clk/qcom/Kconfig | 4 ++ - drivers/clk/qcom/Makefile | 1 + - drivers/clk/qcom/clk-krait.c | 124 +++++++++++++++++++++++++++++++++++ - drivers/clk/qcom/clk-krait.h | 37 +++++++++++ - 4 files changed, 166 insertions(+) - create mode 100644 drivers/clk/qcom/clk-krait.c - create mode 100644 drivers/clk/qcom/clk-krait.h - ---- a/drivers/clk/qcom/Kconfig -+++ b/drivers/clk/qcom/Kconfig -@@ -1,3 +1,7 @@ -+config KRAIT_CLOCKS -+ bool -+ select KRAIT_L2_ACCESSORS -+ - config QCOM_GDSC - bool - select PM_GENERIC_DOMAINS if PM ---- a/drivers/clk/qcom/Makefile -+++ b/drivers/clk/qcom/Makefile -@@ -11,6 +11,7 @@ clk-qcom-y += clk-branch.o - clk-qcom-y += clk-regmap-divider.o - clk-qcom-y += clk-regmap-mux.o - clk-qcom-y += clk-regmap-mux-div.o -+clk-qcom-$(CONFIG_KRAIT_CLOCKS) += clk-krait.o - clk-qcom-y += clk-hfpll.o - clk-qcom-y += reset.o - clk-qcom-$(CONFIG_QCOM_GDSC) += gdsc.o ---- /dev/null -+++ b/drivers/clk/qcom/clk-krait.c -@@ -0,0 +1,124 @@ -+// SPDX-License-Identifier: GPL-2.0 -+// Copyright (c) 2018, The Linux Foundation. All rights reserved. -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#include -+ -+#include "clk-krait.h" -+ -+/* Secondary and primary muxes share the same cp15 register */ -+static DEFINE_SPINLOCK(krait_clock_reg_lock); -+ -+#define LPL_SHIFT 8 -+static void __krait_mux_set_sel(struct krait_mux_clk *mux, int sel) -+{ -+ unsigned long flags; -+ u32 regval; -+ -+ spin_lock_irqsave(&krait_clock_reg_lock, flags); -+ regval = krait_get_l2_indirect_reg(mux->offset); -+ regval &= ~(mux->mask << mux->shift); -+ regval |= (sel & mux->mask) << mux->shift; -+ if (mux->lpl) { -+ regval &= ~(mux->mask << (mux->shift + LPL_SHIFT)); -+ regval |= (sel & mux->mask) << (mux->shift + LPL_SHIFT); -+ } -+ krait_set_l2_indirect_reg(mux->offset, regval); -+ spin_unlock_irqrestore(&krait_clock_reg_lock, flags); -+ -+ /* Wait for switch to complete. */ -+ mb(); -+ udelay(1); -+} -+ -+static int krait_mux_set_parent(struct clk_hw *hw, u8 index) -+{ -+ struct krait_mux_clk *mux = to_krait_mux_clk(hw); -+ u32 sel; -+ -+ sel = clk_mux_reindex(index, mux->parent_map, 0); -+ mux->en_mask = sel; -+ /* Don't touch mux if CPU is off as it won't work */ -+ if (__clk_is_enabled(hw->clk)) -+ __krait_mux_set_sel(mux, sel); -+ -+ return 0; -+} -+ -+static u8 krait_mux_get_parent(struct clk_hw *hw) -+{ -+ struct krait_mux_clk *mux = to_krait_mux_clk(hw); -+ u32 sel; -+ -+ sel = krait_get_l2_indirect_reg(mux->offset); -+ sel >>= mux->shift; -+ sel &= mux->mask; -+ mux->en_mask = sel; -+ -+ return clk_mux_get_parent(hw, sel, mux->parent_map, 0); -+} -+ -+const struct clk_ops krait_mux_clk_ops = { -+ .set_parent = krait_mux_set_parent, -+ .get_parent = krait_mux_get_parent, -+ .determine_rate = __clk_mux_determine_rate_closest, -+}; -+EXPORT_SYMBOL_GPL(krait_mux_clk_ops); -+ -+/* The divider can divide by 2, 4, 6 and 8. But we only really need div-2. */ -+static long krait_div2_round_rate(struct clk_hw *hw, unsigned long rate, -+ unsigned long *parent_rate) -+{ -+ *parent_rate = clk_hw_round_rate(clk_hw_get_parent(hw), rate * 2); -+ return DIV_ROUND_UP(*parent_rate, 2); -+} -+ -+static int krait_div2_set_rate(struct clk_hw *hw, unsigned long rate, -+ unsigned long parent_rate) -+{ -+ struct krait_div2_clk *d = to_krait_div2_clk(hw); -+ unsigned long flags; -+ u32 val; -+ u32 mask = BIT(d->width) - 1; -+ -+ if (d->lpl) -+ mask = mask << (d->shift + LPL_SHIFT) | mask << d->shift; -+ -+ spin_lock_irqsave(&krait_clock_reg_lock, flags); -+ val = krait_get_l2_indirect_reg(d->offset); -+ val &= ~mask; -+ krait_set_l2_indirect_reg(d->offset, val); -+ spin_unlock_irqrestore(&krait_clock_reg_lock, flags); -+ -+ return 0; -+} -+ -+static unsigned long -+krait_div2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) -+{ -+ struct krait_div2_clk *d = to_krait_div2_clk(hw); -+ u32 mask = BIT(d->width) - 1; -+ u32 div; -+ -+ div = krait_get_l2_indirect_reg(d->offset); -+ div >>= d->shift; -+ div &= mask; -+ div = (div + 1) * 2; -+ -+ return DIV_ROUND_UP(parent_rate, div); -+} -+ -+const struct clk_ops krait_div2_clk_ops = { -+ .round_rate = krait_div2_round_rate, -+ .set_rate = krait_div2_set_rate, -+ .recalc_rate = krait_div2_recalc_rate, -+}; -+EXPORT_SYMBOL_GPL(krait_div2_clk_ops); ---- /dev/null -+++ b/drivers/clk/qcom/clk-krait.h -@@ -0,0 +1,37 @@ -+/* SPDX-License-Identifier: GPL-2.0 */ -+ -+#ifndef __QCOM_CLK_KRAIT_H -+#define __QCOM_CLK_KRAIT_H -+ -+#include -+ -+struct krait_mux_clk { -+ unsigned int *parent_map; -+ u32 offset; -+ u32 mask; -+ u32 shift; -+ u32 en_mask; -+ bool lpl; -+ -+ struct clk_hw hw; -+ struct notifier_block clk_nb; -+}; -+ -+#define to_krait_mux_clk(_hw) container_of(_hw, struct krait_mux_clk, hw) -+ -+extern const struct clk_ops krait_mux_clk_ops; -+ -+struct krait_div2_clk { -+ u32 offset; -+ u8 width; -+ u32 shift; -+ bool lpl; -+ -+ struct clk_hw hw; -+}; -+ -+#define to_krait_div2_clk(_hw) container_of(_hw, struct krait_div2_clk, hw) -+ -+extern const struct clk_ops krait_div2_clk_ops; -+ -+#endif diff --git a/target/linux/ipq806x/patches-4.19/0034-0008-clk-qcom-Add-KPSS-ACC-GCC-driver.patch b/target/linux/ipq806x/patches-4.19/0034-0008-clk-qcom-Add-KPSS-ACC-GCC-driver.patch deleted file mode 100644 index aa19ea2e3f..0000000000 --- a/target/linux/ipq806x/patches-4.19/0034-0008-clk-qcom-Add-KPSS-ACC-GCC-driver.patch +++ /dev/null @@ -1,134 +0,0 @@ -From 3ddc3564d3c9f097986bd4ccbe34152413811335 Mon Sep 17 00:00:00 2001 -From: Stephen Boyd -Date: Tue, 14 Aug 2018 17:42:27 +0530 -Subject: [PATCH 08/12] clk: qcom: Add KPSS ACC/GCC driver - -The ACC and GCC regions present in KPSSv1 contain registers to -control clocks and power to each Krait CPU and L2. For CPUfreq -purposes probe these devices and expose a mux clock that chooses -between PXO and PLL8. - -Cc: -Signed-off-by: Stephen Boyd -Signed-off-by: Sricharan R -Tested-by: Craig Tatlor -Signed-off-by: Stephen Boyd ---- - drivers/clk/qcom/Kconfig | 8 ++++ - drivers/clk/qcom/Makefile | 1 + - drivers/clk/qcom/kpss-xcc.c | 87 +++++++++++++++++++++++++++++++++++++ - 3 files changed, 96 insertions(+) - create mode 100644 drivers/clk/qcom/kpss-xcc.c - ---- a/drivers/clk/qcom/Kconfig -+++ b/drivers/clk/qcom/Kconfig -@@ -284,3 +284,11 @@ config QCOM_HFPLL - Support for the high-frequency PLLs present on Qualcomm devices. - Say Y if you want to support CPU frequency scaling on devices - such as MSM8974, APQ8084, etc. -+ -+config KPSS_XCC -+ tristate "KPSS Clock Controller" -+ depends on COMMON_CLK_QCOM -+ help -+ Support for the Krait ACC and GCC clock controllers. Say Y -+ if you want to support CPU frequency scaling on devices such -+ as MSM8960, APQ8064, etc. ---- a/drivers/clk/qcom/Makefile -+++ b/drivers/clk/qcom/Makefile -@@ -45,4 +45,5 @@ obj-$(CONFIG_SDM_DISPCC_845) += dispcc-s - obj-$(CONFIG_SDM_GCC_845) += gcc-sdm845.o - obj-$(CONFIG_SDM_VIDEOCC_845) += videocc-sdm845.o - obj-$(CONFIG_SPMI_PMIC_CLKDIV) += clk-spmi-pmic-div.o -+obj-$(CONFIG_KPSS_XCC) += kpss-xcc.o - obj-$(CONFIG_QCOM_HFPLL) += hfpll.o ---- /dev/null -+++ b/drivers/clk/qcom/kpss-xcc.c -@@ -0,0 +1,87 @@ -+// SPDX-License-Identifier: GPL-2.0 -+// Copyright (c) 2018, The Linux Foundation. All rights reserved. -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+static const char *aux_parents[] = { -+ "pll8_vote", -+ "pxo", -+}; -+ -+static unsigned int aux_parent_map[] = { -+ 3, -+ 0, -+}; -+ -+static const struct of_device_id kpss_xcc_match_table[] = { -+ { .compatible = "qcom,kpss-acc-v1", .data = (void *)1UL }, -+ { .compatible = "qcom,kpss-gcc" }, -+ {} -+}; -+MODULE_DEVICE_TABLE(of, kpss_xcc_match_table); -+ -+static int kpss_xcc_driver_probe(struct platform_device *pdev) -+{ -+ const struct of_device_id *id; -+ struct clk *clk; -+ struct resource *res; -+ void __iomem *base; -+ const char *name; -+ -+ id = of_match_device(kpss_xcc_match_table, &pdev->dev); -+ if (!id) -+ return -ENODEV; -+ -+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); -+ base = devm_ioremap_resource(&pdev->dev, res); -+ if (IS_ERR(base)) -+ return PTR_ERR(base); -+ -+ if (id->data) { -+ if (of_property_read_string_index(pdev->dev.of_node, -+ "clock-output-names", -+ 0, &name)) -+ return -ENODEV; -+ base += 0x14; -+ } else { -+ name = "acpu_l2_aux"; -+ base += 0x28; -+ } -+ -+ clk = clk_register_mux_table(&pdev->dev, name, aux_parents, -+ ARRAY_SIZE(aux_parents), 0, base, 0, 0x3, -+ 0, aux_parent_map, NULL); -+ -+ platform_set_drvdata(pdev, clk); -+ -+ return PTR_ERR_OR_ZERO(clk); -+} -+ -+static int kpss_xcc_driver_remove(struct platform_device *pdev) -+{ -+ clk_unregister_mux(platform_get_drvdata(pdev)); -+ return 0; -+} -+ -+static struct platform_driver kpss_xcc_driver = { -+ .probe = kpss_xcc_driver_probe, -+ .remove = kpss_xcc_driver_remove, -+ .driver = { -+ .name = "kpss-xcc", -+ .of_match_table = kpss_xcc_match_table, -+ }, -+}; -+module_platform_driver(kpss_xcc_driver); -+ -+MODULE_DESCRIPTION("Krait Processor Sub System (KPSS) Clock Driver"); -+MODULE_LICENSE("GPL v2"); -+MODULE_ALIAS("platform:kpss-xcc"); diff --git a/target/linux/ipq806x/patches-4.19/0034-0009-dt-bindings-arm-Document-qcom-kpss-gcc.patch b/target/linux/ipq806x/patches-4.19/0034-0009-dt-bindings-arm-Document-qcom-kpss-gcc.patch deleted file mode 100644 index 6af40895bc..0000000000 --- a/target/linux/ipq806x/patches-4.19/0034-0009-dt-bindings-arm-Document-qcom-kpss-gcc.patch +++ /dev/null @@ -1,99 +0,0 @@ -From 40e5ddf4f84869815129551f4a8cfc2c223ebeae Mon Sep 17 00:00:00 2001 -From: Stephen Boyd -Date: Tue, 14 Aug 2018 17:42:28 +0530 -Subject: [PATCH 09/12] dt-bindings: arm: Document qcom,kpss-gcc - -The ACC and GCC regions present in KPSSv1 contain registers to -control clocks and power to each Krait CPU and L2. Documenting -the bindings here. - -Reviewed-by: Rob Herring -Signed-off-by: Stephen Boyd -Signed-off-by: Sricharan R -Tested-by: Craig Tatlor -Signed-off-by: Stephen Boyd ---- - .../bindings/arm/msm/qcom,kpss-acc.txt | 19 ++++++++ - .../bindings/arm/msm/qcom,kpss-gcc.txt | 44 +++++++++++++++++++ - 2 files changed, 63 insertions(+) - create mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt - ---- a/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt -+++ b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt -@@ -21,10 +21,29 @@ PROPERTIES - the register region. An optional second element specifies - the base address and size of the alias register region. - -+- clocks: -+ Usage: required -+ Value type: -+ Definition: reference to the pll parents. -+ -+- clock-names: -+ Usage: required -+ Value type: -+ Definition: must be "pll8_vote", "pxo". -+ -+- clock-output-names: -+ Usage: optional -+ Value type: -+ Definition: Name of the output clock. Typically acpuX_aux where X is a -+ CPU number starting at 0. -+ - Example: - - clock-controller@2088000 { - compatible = "qcom,kpss-acc-v2"; - reg = <0x02088000 0x1000>, - <0x02008000 0x1000>; -+ clocks = <&gcc PLL8_VOTE>, <&gcc PXO_SRC>; -+ clock-names = "pll8_vote", "pxo"; -+ clock-output-names = "acpu0_aux"; - }; ---- /dev/null -+++ b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt -@@ -0,0 +1,44 @@ -+Krait Processor Sub-system (KPSS) Global Clock Controller (GCC) -+ -+PROPERTIES -+ -+- compatible: -+ Usage: required -+ Value type: -+ Definition: should be one of the following. The generic compatible -+ "qcom,kpss-gcc" should also be included. -+ "qcom,kpss-gcc-ipq8064", "qcom,kpss-gcc" -+ "qcom,kpss-gcc-apq8064", "qcom,kpss-gcc" -+ "qcom,kpss-gcc-msm8974", "qcom,kpss-gcc" -+ "qcom,kpss-gcc-msm8960", "qcom,kpss-gcc" -+ -+- reg: -+ Usage: required -+ Value type: -+ Definition: base address and size of the register region -+ -+- clocks: -+ Usage: required -+ Value type: -+ Definition: reference to the pll parents. -+ -+- clock-names: -+ Usage: required -+ Value type: -+ Definition: must be "pll8_vote", "pxo". -+ -+- clock-output-names: -+ Usage: required -+ Value type: -+ Definition: Name of the output clock. Typically acpu_l2_aux indicating -+ an L2 cache auxiliary clock. -+ -+Example: -+ -+ l2cc: clock-controller@2011000 { -+ compatible = "qcom,kpss-gcc-ipq8064", "qcom,kpss-gcc"; -+ reg = <0x2011000 0x1000>; -+ clocks = <&gcc PLL8_VOTE>, <&gcc PXO_SRC>; -+ clock-names = "pll8_vote", "pxo"; -+ clock-output-names = "acpu_l2_aux"; -+ }; diff --git a/target/linux/ipq806x/patches-4.19/0034-0010-clk-qcom-Add-Krait-clock-controller-driver.patch b/target/linux/ipq806x/patches-4.19/0034-0010-clk-qcom-Add-Krait-clock-controller-driver.patch deleted file mode 100644 index 7ee1f50f41..0000000000 --- a/target/linux/ipq806x/patches-4.19/0034-0010-clk-qcom-Add-Krait-clock-controller-driver.patch +++ /dev/null @@ -1,409 +0,0 @@ -From bb5c4a85051e5e0be39c775b6df85521f2ae807d Mon Sep 17 00:00:00 2001 -From: Stephen Boyd -Date: Tue, 14 Aug 2018 17:42:29 +0530 -Subject: [PATCH 10/12] clk: qcom: Add Krait clock controller driver - -The Krait CPU clocks are made up of a primary mux and secondary -mux for each CPU and the L2, controlled via cp15 accessors. For -Kraits within KPSSv1 each secondary mux accepts a different aux -source, but on KPSSv2 each secondary mux accepts the same aux -source. - -Cc: -Signed-off-by: Stephen Boyd -Signed-off-by: Sricharan R -Tested-by: Craig Tatlor -Signed-off-by: Stephen Boyd ---- - drivers/clk/qcom/Kconfig | 8 + - drivers/clk/qcom/Makefile | 1 + - drivers/clk/qcom/clk-krait.c | 4 +- - drivers/clk/qcom/krait-cc.c | 341 +++++++++++++++++++++++++++++++++++ - 4 files changed, 352 insertions(+), 2 deletions(-) - create mode 100644 drivers/clk/qcom/krait-cc.c - ---- a/drivers/clk/qcom/Kconfig -+++ b/drivers/clk/qcom/Kconfig -@@ -292,3 +292,11 @@ config KPSS_XCC - Support for the Krait ACC and GCC clock controllers. Say Y - if you want to support CPU frequency scaling on devices such - as MSM8960, APQ8064, etc. -+ -+config KRAITCC -+ tristate "Krait Clock Controller" -+ depends on COMMON_CLK_QCOM && ARM -+ select KRAIT_CLOCKS -+ help -+ Support for the Krait CPU clocks on Qualcomm devices. -+ Say Y if you want to support CPU frequency scaling. ---- a/drivers/clk/qcom/Makefile -+++ b/drivers/clk/qcom/Makefile -@@ -47,3 +47,4 @@ obj-$(CONFIG_SDM_VIDEOCC_845) += videocc - obj-$(CONFIG_SPMI_PMIC_CLKDIV) += clk-spmi-pmic-div.o - obj-$(CONFIG_KPSS_XCC) += kpss-xcc.o - obj-$(CONFIG_QCOM_HFPLL) += hfpll.o -+obj-$(CONFIG_KRAITCC) += krait-cc.o ---- a/drivers/clk/qcom/clk-krait.c -+++ b/drivers/clk/qcom/clk-krait.c -@@ -44,7 +44,7 @@ static int krait_mux_set_parent(struct c - struct krait_mux_clk *mux = to_krait_mux_clk(hw); - u32 sel; - -- sel = clk_mux_reindex(index, mux->parent_map, 0); -+ sel = clk_mux_index_to_val(mux->parent_map, 0, index); - mux->en_mask = sel; - /* Don't touch mux if CPU is off as it won't work */ - if (__clk_is_enabled(hw->clk)) -@@ -63,7 +63,7 @@ static u8 krait_mux_get_parent(struct cl - sel &= mux->mask; - mux->en_mask = sel; - -- return clk_mux_get_parent(hw, sel, mux->parent_map, 0); -+ return clk_mux_val_to_index(hw, mux->parent_map, 0, sel); - } - - const struct clk_ops krait_mux_clk_ops = { ---- /dev/null -+++ b/drivers/clk/qcom/krait-cc.c -@@ -0,0 +1,341 @@ -+// SPDX-License-Identifier: GPL-2.0 -+// Copyright (c) 2018, The Linux Foundation. All rights reserved. -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#include "clk-krait.h" -+ -+static unsigned int sec_mux_map[] = { -+ 2, -+ 0, -+}; -+ -+static unsigned int pri_mux_map[] = { -+ 1, -+ 2, -+ 0, -+}; -+ -+static int -+krait_add_div(struct device *dev, int id, const char *s, unsigned int offset) -+{ -+ struct krait_div2_clk *div; -+ struct clk_init_data init = { -+ .num_parents = 1, -+ .ops = &krait_div2_clk_ops, -+ .flags = CLK_SET_RATE_PARENT, -+ }; -+ const char *p_names[1]; -+ struct clk *clk; -+ -+ div = devm_kzalloc(dev, sizeof(*div), GFP_KERNEL); -+ if (!div) -+ return -ENOMEM; -+ -+ div->width = 2; -+ div->shift = 6; -+ div->lpl = id >= 0; -+ div->offset = offset; -+ div->hw.init = &init; -+ -+ init.name = kasprintf(GFP_KERNEL, "hfpll%s_div", s); -+ if (!init.name) -+ return -ENOMEM; -+ -+ init.parent_names = p_names; -+ p_names[0] = kasprintf(GFP_KERNEL, "hfpll%s", s); -+ if (!p_names[0]) { -+ kfree(init.name); -+ return -ENOMEM; -+ } -+ -+ clk = devm_clk_register(dev, &div->hw); -+ kfree(p_names[0]); -+ kfree(init.name); -+ -+ return PTR_ERR_OR_ZERO(clk); -+} -+ -+static int -+krait_add_sec_mux(struct device *dev, int id, const char *s, -+ unsigned int offset, bool unique_aux) -+{ -+ struct krait_mux_clk *mux; -+ static const char *sec_mux_list[] = { -+ "acpu_aux", -+ "qsb", -+ }; -+ struct clk_init_data init = { -+ .parent_names = sec_mux_list, -+ .num_parents = ARRAY_SIZE(sec_mux_list), -+ .ops = &krait_mux_clk_ops, -+ .flags = CLK_SET_RATE_PARENT, -+ }; -+ struct clk *clk; -+ -+ mux = devm_kzalloc(dev, sizeof(*mux), GFP_KERNEL); -+ if (!mux) -+ return -ENOMEM; -+ -+ mux->offset = offset; -+ mux->lpl = id >= 0; -+ mux->mask = 0x3; -+ mux->shift = 2; -+ mux->parent_map = sec_mux_map; -+ mux->hw.init = &init; -+ -+ init.name = kasprintf(GFP_KERNEL, "krait%s_sec_mux", s); -+ if (!init.name) -+ return -ENOMEM; -+ -+ if (unique_aux) { -+ sec_mux_list[0] = kasprintf(GFP_KERNEL, "acpu%s_aux", s); -+ if (!sec_mux_list[0]) { -+ clk = ERR_PTR(-ENOMEM); -+ goto err_aux; -+ } -+ } -+ -+ clk = devm_clk_register(dev, &mux->hw); -+ -+ if (unique_aux) -+ kfree(sec_mux_list[0]); -+err_aux: -+ kfree(init.name); -+ return PTR_ERR_OR_ZERO(clk); -+} -+ -+static struct clk * -+krait_add_pri_mux(struct device *dev, int id, const char *s, -+ unsigned int offset) -+{ -+ struct krait_mux_clk *mux; -+ const char *p_names[3]; -+ struct clk_init_data init = { -+ .parent_names = p_names, -+ .num_parents = ARRAY_SIZE(p_names), -+ .ops = &krait_mux_clk_ops, -+ .flags = CLK_SET_RATE_PARENT, -+ }; -+ struct clk *clk; -+ -+ mux = devm_kzalloc(dev, sizeof(*mux), GFP_KERNEL); -+ if (!mux) -+ return ERR_PTR(-ENOMEM); -+ -+ mux->mask = 0x3; -+ mux->shift = 0; -+ mux->offset = offset; -+ mux->lpl = id >= 0; -+ mux->parent_map = pri_mux_map; -+ mux->hw.init = &init; -+ -+ init.name = kasprintf(GFP_KERNEL, "krait%s_pri_mux", s); -+ if (!init.name) -+ return ERR_PTR(-ENOMEM); -+ -+ p_names[0] = kasprintf(GFP_KERNEL, "hfpll%s", s); -+ if (!p_names[0]) { -+ clk = ERR_PTR(-ENOMEM); -+ goto err_p0; -+ } -+ -+ p_names[1] = kasprintf(GFP_KERNEL, "hfpll%s_div", s); -+ if (!p_names[1]) { -+ clk = ERR_PTR(-ENOMEM); -+ goto err_p1; -+ } -+ -+ p_names[2] = kasprintf(GFP_KERNEL, "krait%s_sec_mux", s); -+ if (!p_names[2]) { -+ clk = ERR_PTR(-ENOMEM); -+ goto err_p2; -+ } -+ -+ clk = devm_clk_register(dev, &mux->hw); -+ -+ kfree(p_names[2]); -+err_p2: -+ kfree(p_names[1]); -+err_p1: -+ kfree(p_names[0]); -+err_p0: -+ kfree(init.name); -+ return clk; -+} -+ -+/* id < 0 for L2, otherwise id == physical CPU number */ -+static struct clk *krait_add_clks(struct device *dev, int id, bool unique_aux) -+{ -+ int ret; -+ unsigned int offset; -+ void *p = NULL; -+ const char *s; -+ struct clk *clk; -+ -+ if (id >= 0) { -+ offset = 0x4501 + (0x1000 * id); -+ s = p = kasprintf(GFP_KERNEL, "%d", id); -+ if (!s) -+ return ERR_PTR(-ENOMEM); -+ } else { -+ offset = 0x500; -+ s = "_l2"; -+ } -+ -+ ret = krait_add_div(dev, id, s, offset); -+ if (ret) { -+ clk = ERR_PTR(ret); -+ goto err; -+ } -+ -+ ret = krait_add_sec_mux(dev, id, s, offset, unique_aux); -+ if (ret) { -+ clk = ERR_PTR(ret); -+ goto err; -+ } -+ -+ clk = krait_add_pri_mux(dev, id, s, offset); -+err: -+ kfree(p); -+ return clk; -+} -+ -+static struct clk *krait_of_get(struct of_phandle_args *clkspec, void *data) -+{ -+ unsigned int idx = clkspec->args[0]; -+ struct clk **clks = data; -+ -+ if (idx >= 5) { -+ pr_err("%s: invalid clock index %d\n", __func__, idx); -+ return ERR_PTR(-EINVAL); -+ } -+ -+ return clks[idx] ? : ERR_PTR(-ENODEV); -+} -+ -+static const struct of_device_id krait_cc_match_table[] = { -+ { .compatible = "qcom,krait-cc-v1", (void *)1UL }, -+ { .compatible = "qcom,krait-cc-v2" }, -+ {} -+}; -+MODULE_DEVICE_TABLE(of, krait_cc_match_table); -+ -+static int krait_cc_probe(struct platform_device *pdev) -+{ -+ struct device *dev = &pdev->dev; -+ const struct of_device_id *id; -+ unsigned long cur_rate, aux_rate; -+ int cpu; -+ struct clk *clk; -+ struct clk **clks; -+ struct clk *l2_pri_mux_clk; -+ -+ id = of_match_device(krait_cc_match_table, dev); -+ if (!id) -+ return -ENODEV; -+ -+ /* Rate is 1 because 0 causes problems for __clk_mux_determine_rate */ -+ clk = clk_register_fixed_rate(dev, "qsb", NULL, 0, 1); -+ if (IS_ERR(clk)) -+ return PTR_ERR(clk); -+ -+ if (!id->data) { -+ clk = clk_register_fixed_factor(dev, "acpu_aux", -+ "gpll0_vote", 0, 1, 2); -+ if (IS_ERR(clk)) -+ return PTR_ERR(clk); -+ } -+ -+ /* Krait configurations have at most 4 CPUs and one L2 */ -+ clks = devm_kcalloc(dev, 5, sizeof(*clks), GFP_KERNEL); -+ if (!clks) -+ return -ENOMEM; -+ -+ for_each_possible_cpu(cpu) { -+ clk = krait_add_clks(dev, cpu, id->data); -+ if (IS_ERR(clk)) -+ return PTR_ERR(clk); -+ clks[cpu] = clk; -+ } -+ -+ l2_pri_mux_clk = krait_add_clks(dev, -1, id->data); -+ if (IS_ERR(l2_pri_mux_clk)) -+ return PTR_ERR(l2_pri_mux_clk); -+ clks[4] = l2_pri_mux_clk; -+ -+ /* -+ * We don't want the CPU or L2 clocks to be turned off at late init -+ * if CPUFREQ or HOTPLUG configs are disabled. So, bump up the -+ * refcount of these clocks. Any cpufreq/hotplug manager can assume -+ * that the clocks have already been prepared and enabled by the time -+ * they take over. -+ */ -+ for_each_online_cpu(cpu) { -+ clk_prepare_enable(l2_pri_mux_clk); -+ WARN(clk_prepare_enable(clks[cpu]), -+ "Unable to turn on CPU%d clock", cpu); -+ } -+ -+ /* -+ * Force reinit of HFPLLs and muxes to overwrite any potential -+ * incorrect configuration of HFPLLs and muxes by the bootloader. -+ * While at it, also make sure the cores are running at known rates -+ * and print the current rate. -+ * -+ * The clocks are set to aux clock rate first to make sure the -+ * secondary mux is not sourcing off of QSB. The rate is then set to -+ * two different rates to force a HFPLL reinit under all -+ * circumstances. -+ */ -+ cur_rate = clk_get_rate(l2_pri_mux_clk); -+ aux_rate = 384000000; -+ if (cur_rate == 1) { -+ pr_info("L2 @ QSB rate. Forcing new rate.\n"); -+ cur_rate = aux_rate; -+ } -+ clk_set_rate(l2_pri_mux_clk, aux_rate); -+ clk_set_rate(l2_pri_mux_clk, 2); -+ clk_set_rate(l2_pri_mux_clk, cur_rate); -+ pr_info("L2 @ %lu KHz\n", clk_get_rate(l2_pri_mux_clk) / 1000); -+ for_each_possible_cpu(cpu) { -+ clk = clks[cpu]; -+ cur_rate = clk_get_rate(clk); -+ if (cur_rate == 1) { -+ pr_info("CPU%d @ QSB rate. Forcing new rate.\n", cpu); -+ cur_rate = aux_rate; -+ } -+ -+ clk_set_rate(clk, aux_rate); -+ clk_set_rate(clk, 2); -+ clk_set_rate(clk, cur_rate); -+ pr_info("CPU%d @ %lu KHz\n", cpu, clk_get_rate(clk) / 1000); -+ } -+ -+ of_clk_add_provider(dev->of_node, krait_of_get, clks); -+ -+ return 0; -+} -+ -+static struct platform_driver krait_cc_driver = { -+ .probe = krait_cc_probe, -+ .driver = { -+ .name = "krait-cc", -+ .of_match_table = krait_cc_match_table, -+ }, -+}; -+module_platform_driver(krait_cc_driver); -+ -+MODULE_DESCRIPTION("Krait CPU Clock Driver"); -+MODULE_LICENSE("GPL v2"); -+MODULE_ALIAS("platform:krait-cc"); diff --git a/target/linux/ipq806x/patches-4.19/0034-0011-dt-bindings-clock-Document-qcom-krait-cc.patch b/target/linux/ipq806x/patches-4.19/0034-0011-dt-bindings-clock-Document-qcom-krait-cc.patch deleted file mode 100644 index 13e05c425a..0000000000 --- a/target/linux/ipq806x/patches-4.19/0034-0011-dt-bindings-clock-Document-qcom-krait-cc.patch +++ /dev/null @@ -1,55 +0,0 @@ -From bf4503ccf321811192cb07f9711556237c3cf668 Mon Sep 17 00:00:00 2001 -From: Stephen Boyd -Date: Tue, 14 Aug 2018 17:42:30 +0530 -Subject: [PATCH 11/12] dt-bindings: clock: Document qcom,krait-cc - -The Krait clock controller controls the krait CPU and the L2 clocks -consisting a primary mux and secondary mux. Add document for that. - -Reviewed-by: Rob Herring -Signed-off-by: Stephen Boyd -Signed-off-by: Sricharan R -Tested-by: Craig Tatlor -Signed-off-by: Stephen Boyd ---- - .../bindings/clock/qcom,krait-cc.txt | 34 +++++++++++++++++++ - 1 file changed, 34 insertions(+) - create mode 100644 Documentation/devicetree/bindings/clock/qcom,krait-cc.txt - ---- /dev/null -+++ b/Documentation/devicetree/bindings/clock/qcom,krait-cc.txt -@@ -0,0 +1,34 @@ -+Krait Clock Controller -+ -+PROPERTIES -+ -+- compatible: -+ Usage: required -+ Value type: -+ Definition: must be one of: -+ "qcom,krait-cc-v1" -+ "qcom,krait-cc-v2" -+ -+- #clock-cells: -+ Usage: required -+ Value type: -+ Definition: must be 1 -+ -+- clocks: -+ Usage: required -+ Value type: -+ Definition: reference to the clock parents of hfpll, secondary muxes. -+ -+- clock-names: -+ Usage: required -+ Value type: -+ Definition: must be "hfpll0", "hfpll1", "acpu0_aux", "acpu1_aux", "qsb". -+ -+Example: -+ -+ kraitcc: clock-controller { -+ compatible = "qcom,krait-cc-v1"; -+ clocks = <&hfpll0>, <&hfpll1>, <&acpu0_aux>, <&acpu1_aux>, ; -+ clock-names = "hfpll0", "hfpll1", "acpu0_aux", "acpu1_aux", "qsb"; -+ #clock-cells = <1>; -+ }; diff --git a/target/linux/ipq806x/patches-4.19/0034-0012-clk-qcom-Add-safe-switch-hook-for-krait-mux-clocks.patch b/target/linux/ipq806x/patches-4.19/0034-0012-clk-qcom-Add-safe-switch-hook-for-krait-mux-clocks.patch deleted file mode 100644 index 847b4809a3..0000000000 --- a/target/linux/ipq806x/patches-4.19/0034-0012-clk-qcom-Add-safe-switch-hook-for-krait-mux-clocks.patch +++ /dev/null @@ -1,152 +0,0 @@ -From 77612720a2362230af726baa4149c40ec7a7fb05 Mon Sep 17 00:00:00 2001 -From: Sricharan R -Date: Tue, 14 Aug 2018 17:42:31 +0530 -Subject: [PATCH 12/12] clk: qcom: Add safe switch hook for krait mux clocks - -When the Hfplls are reprogrammed during the rate change, -the primary muxes which are sourced from the same hfpll -for higher frequencies, needs to be switched to the 'safe -secondary mux' as the parent for that small window. This -is done by registering a clk notifier for the muxes and -switching to the safe parent in the PRE_RATE_CHANGE notifier -and back to the original parent in the POST_RATE_CHANGE notifier. - -Signed-off-by: Sricharan R -Tested-by: Craig Tatlor -Signed-off-by: Stephen Boyd ---- - drivers/clk/qcom/clk-krait.c | 2 ++ - drivers/clk/qcom/clk-krait.h | 3 ++ - drivers/clk/qcom/krait-cc.c | 56 ++++++++++++++++++++++++++++++++++++ - 3 files changed, 61 insertions(+) - ---- a/drivers/clk/qcom/clk-krait.c -+++ b/drivers/clk/qcom/clk-krait.c -@@ -50,6 +50,8 @@ static int krait_mux_set_parent(struct c - if (__clk_is_enabled(hw->clk)) - __krait_mux_set_sel(mux, sel); - -+ mux->reparent = true; -+ - return 0; - } - ---- a/drivers/clk/qcom/clk-krait.h -+++ b/drivers/clk/qcom/clk-krait.h -@@ -12,6 +12,9 @@ struct krait_mux_clk { - u32 shift; - u32 en_mask; - bool lpl; -+ u8 safe_sel; -+ u8 old_index; -+ bool reparent; - - struct clk_hw hw; - struct notifier_block clk_nb; ---- a/drivers/clk/qcom/krait-cc.c -+++ b/drivers/clk/qcom/krait-cc.c -@@ -26,6 +26,49 @@ static unsigned int pri_mux_map[] = { - 0, - }; - -+/* -+ * Notifier function for switching the muxes to safe parent -+ * while the hfpll is getting reprogrammed. -+ */ -+static int krait_notifier_cb(struct notifier_block *nb, -+ unsigned long event, -+ void *data) -+{ -+ int ret = 0; -+ struct krait_mux_clk *mux = container_of(nb, struct krait_mux_clk, -+ clk_nb); -+ /* Switch to safe parent */ -+ if (event == PRE_RATE_CHANGE) { -+ mux->old_index = krait_mux_clk_ops.get_parent(&mux->hw); -+ ret = krait_mux_clk_ops.set_parent(&mux->hw, mux->safe_sel); -+ mux->reparent = false; -+ /* -+ * By the time POST_RATE_CHANGE notifier is called, -+ * clk framework itself would have changed the parent for the new rate. -+ * Only otherwise, put back to the old parent. -+ */ -+ } else if (event == POST_RATE_CHANGE) { -+ if (!mux->reparent) -+ ret = krait_mux_clk_ops.set_parent(&mux->hw, -+ mux->old_index); -+ } -+ -+ return notifier_from_errno(ret); -+} -+ -+static int krait_notifier_register(struct device *dev, struct clk *clk, -+ struct krait_mux_clk *mux) -+{ -+ int ret = 0; -+ -+ mux->clk_nb.notifier_call = krait_notifier_cb; -+ ret = clk_notifier_register(clk, &mux->clk_nb); -+ if (ret) -+ dev_err(dev, "failed to register clock notifier: %d\n", ret); -+ -+ return ret; -+} -+ - static int - krait_add_div(struct device *dev, int id, const char *s, unsigned int offset) - { -@@ -70,6 +113,7 @@ static int - krait_add_sec_mux(struct device *dev, int id, const char *s, - unsigned int offset, bool unique_aux) - { -+ int ret; - struct krait_mux_clk *mux; - static const char *sec_mux_list[] = { - "acpu_aux", -@@ -93,6 +137,7 @@ krait_add_sec_mux(struct device *dev, in - mux->shift = 2; - mux->parent_map = sec_mux_map; - mux->hw.init = &init; -+ mux->safe_sel = 0; - - init.name = kasprintf(GFP_KERNEL, "krait%s_sec_mux", s); - if (!init.name) -@@ -108,6 +153,11 @@ krait_add_sec_mux(struct device *dev, in - - clk = devm_clk_register(dev, &mux->hw); - -+ ret = krait_notifier_register(dev, clk, mux); -+ if (ret) -+ goto unique_aux; -+ -+unique_aux: - if (unique_aux) - kfree(sec_mux_list[0]); - err_aux: -@@ -119,6 +169,7 @@ static struct clk * - krait_add_pri_mux(struct device *dev, int id, const char *s, - unsigned int offset) - { -+ int ret; - struct krait_mux_clk *mux; - const char *p_names[3]; - struct clk_init_data init = { -@@ -139,6 +190,7 @@ krait_add_pri_mux(struct device *dev, in - mux->lpl = id >= 0; - mux->parent_map = pri_mux_map; - mux->hw.init = &init; -+ mux->safe_sel = 2; - - init.name = kasprintf(GFP_KERNEL, "krait%s_pri_mux", s); - if (!init.name) -@@ -164,6 +216,10 @@ krait_add_pri_mux(struct device *dev, in - - clk = devm_clk_register(dev, &mux->hw); - -+ ret = krait_notifier_register(dev, clk, mux); -+ if (ret) -+ goto err_p3; -+err_p3: - kfree(p_names[2]); - err_p2: - kfree(p_names[1]); diff --git a/target/linux/ipq806x/patches-4.19/0035-qcom-cpufreq-nvmem-qcm-kyrp_make_Some_variables_static.patch b/target/linux/ipq806x/patches-4.19/0035-qcom-cpufreq-nvmem-qcm-kyrp_make_Some_variables_static.patch deleted file mode 100644 index a51153b2aa..0000000000 --- a/target/linux/ipq806x/patches-4.19/0035-qcom-cpufreq-nvmem-qcm-kyrp_make_Some_variables_static.patch +++ /dev/null @@ -1,25 +0,0 @@ -From 50c0b12f098fb3cfac7abcc0f2b5409f6bac5fa2 Mon Sep 17 00:00:00 2001 -From: Yangtao Li -Date: Mon, 4 Feb 2019 01:13:10 -0500 -Subject: [PATCH] cpufreq: qcom-kryo: make some variables static - -The variables are local to the source and do not -need to be in global scope, so make them static. - -Signed-off-by: Yangtao Li -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/qcom-cpufreq-kryo.c | 2 +- - 1 file changed, 1 insertion(+), 1 deletion(-) - ---- a/drivers/cpufreq/qcom-cpufreq-kryo.c -+++ b/drivers/cpufreq/qcom-cpufreq-kryo.c -@@ -42,7 +42,7 @@ enum _msm8996_version { - NUM_OF_MSM8996_VERSIONS, - }; - --struct platform_device *cpufreq_dt_pdev, *kryo_cpufreq_pdev; -+static struct platform_device *cpufreq_dt_pdev, *kryo_cpufreq_pdev; - - static enum _msm8996_version qcom_cpufreq_kryo_get_msm_id(void) - { diff --git a/target/linux/ipq806x/patches-4.19/0036-qcom-cpufreq-nvmem-Re-organise-kryo-cpufreq-driver.patch b/target/linux/ipq806x/patches-4.19/0036-qcom-cpufreq-nvmem-Re-organise-kryo-cpufreq-driver.patch deleted file mode 100644 index c7e4569616..0000000000 --- a/target/linux/ipq806x/patches-4.19/0036-qcom-cpufreq-nvmem-Re-organise-kryo-cpufreq-driver.patch +++ /dev/null @@ -1,579 +0,0 @@ -From 7d12709544b8b3fb9727a34a664b8380e1e3493a Mon Sep 17 00:00:00 2001 -From: Sricharan R -Date: Thu, 25 Jul 2019 12:41:31 +0200 -Subject: [PATCH] cpufreq: qcom: Re-organise kryo cpufreq to use it for other - nvmem based qcom socs - -The kryo cpufreq driver reads the nvmem cell and uses that data to -populate the opps. There are other qcom cpufreq socs like krait which -does similar thing. Except for the interpretation of the read data, -rest of the driver is same for both the cases. So pull the common things -out for reuse. - -Signed-off-by: Sricharan R -[niklas.cassel@linaro.org: split dt-binding into a separate patch and -do not rename the compatible string. Update MAINTAINERS file.] -Signed-off-by: Niklas Cassel -Reviewed-by: Ilia Lin -Reviewed-by: Stephen Boyd -Signed-off-by: Viresh Kumar ---- - MAINTAINERS | 4 +- - drivers/cpufreq/Kconfig.arm | 4 +- - drivers/cpufreq/Makefile | 2 +- - ...om-cpufreq-kryo.c => qcom-cpufreq-nvmem.c} | 122 +++++++++++------- - 4 files changed, 78 insertions(+), 54 deletions(-) - rename drivers/cpufreq/{qcom-cpufreq-kryo.c => qcom-cpufreq-nvmem.c} (69%) - ---- a/drivers/cpufreq/Kconfig.arm -+++ b/drivers/cpufreq/Kconfig.arm -@@ -110,8 +110,8 @@ config ARM_OMAP2PLUS_CPUFREQ - depends on ARCH_OMAP2PLUS - default ARCH_OMAP2PLUS - --config ARM_QCOM_CPUFREQ_KRYO -- tristate "Qualcomm Kryo based CPUFreq" -+config ARM_QCOM_CPUFREQ_NVMEM -+ tristate "Qualcomm nvmem based CPUFreq" - depends on ARM64 - depends on QCOM_QFPROM - depends on QCOM_SMEM ---- a/drivers/cpufreq/Makefile -+++ b/drivers/cpufreq/Makefile -@@ -64,7 +64,7 @@ obj-$(CONFIG_MACH_MVEBU_V7) += mvebu-cp - obj-$(CONFIG_ARM_OMAP2PLUS_CPUFREQ) += omap-cpufreq.o - obj-$(CONFIG_ARM_PXA2xx_CPUFREQ) += pxa2xx-cpufreq.o - obj-$(CONFIG_PXA3xx) += pxa3xx-cpufreq.o --obj-$(CONFIG_ARM_QCOM_CPUFREQ_KRYO) += qcom-cpufreq-kryo.o -+obj-$(CONFIG_ARM_QCOM_CPUFREQ_NVMEM) += qcom-cpufreq-nvmem.o - obj-$(CONFIG_ARM_S3C2410_CPUFREQ) += s3c2410-cpufreq.o - obj-$(CONFIG_ARM_S3C2412_CPUFREQ) += s3c2412-cpufreq.o - obj-$(CONFIG_ARM_S3C2416_CPUFREQ) += s3c2416-cpufreq.o ---- a/drivers/cpufreq/qcom-cpufreq-kryo.c -+++ /dev/null -@@ -1,249 +0,0 @@ --// SPDX-License-Identifier: GPL-2.0 --/* -- * Copyright (c) 2018, The Linux Foundation. All rights reserved. -- */ -- --/* -- * In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO processors, -- * the CPU frequency subset and voltage value of each OPP varies -- * based on the silicon variant in use. Qualcomm Process Voltage Scaling Tables -- * defines the voltage and frequency value based on the msm-id in SMEM -- * and speedbin blown in the efuse combination. -- * The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC -- * to provide the OPP framework with required information. -- * This is used to determine the voltage and frequency value for each OPP of -- * operating-points-v2 table when it is parsed by the OPP framework. -- */ -- --#include --#include --#include --#include --#include --#include --#include --#include --#include --#include --#include -- --#define MSM_ID_SMEM 137 -- --enum _msm_id { -- MSM8996V3 = 0xF6ul, -- APQ8096V3 = 0x123ul, -- MSM8996SG = 0x131ul, -- APQ8096SG = 0x138ul, --}; -- --enum _msm8996_version { -- MSM8996_V3, -- MSM8996_SG, -- NUM_OF_MSM8996_VERSIONS, --}; -- --static struct platform_device *cpufreq_dt_pdev, *kryo_cpufreq_pdev; -- --static enum _msm8996_version qcom_cpufreq_kryo_get_msm_id(void) --{ -- size_t len; -- u32 *msm_id; -- enum _msm8996_version version; -- -- msm_id = qcom_smem_get(QCOM_SMEM_HOST_ANY, MSM_ID_SMEM, &len); -- if (IS_ERR(msm_id)) -- return NUM_OF_MSM8996_VERSIONS; -- -- /* The first 4 bytes are format, next to them is the actual msm-id */ -- msm_id++; -- -- switch ((enum _msm_id)*msm_id) { -- case MSM8996V3: -- case APQ8096V3: -- version = MSM8996_V3; -- break; -- case MSM8996SG: -- case APQ8096SG: -- version = MSM8996_SG; -- break; -- default: -- version = NUM_OF_MSM8996_VERSIONS; -- } -- -- return version; --} -- --static int qcom_cpufreq_kryo_probe(struct platform_device *pdev) --{ -- struct opp_table **opp_tables; -- enum _msm8996_version msm8996_version; -- struct nvmem_cell *speedbin_nvmem; -- struct device_node *np; -- struct device *cpu_dev; -- unsigned cpu; -- u8 *speedbin; -- u32 versions; -- size_t len; -- int ret; -- -- cpu_dev = get_cpu_device(0); -- if (!cpu_dev) -- return -ENODEV; -- -- msm8996_version = qcom_cpufreq_kryo_get_msm_id(); -- if (NUM_OF_MSM8996_VERSIONS == msm8996_version) { -- dev_err(cpu_dev, "Not Snapdragon 820/821!"); -- return -ENODEV; -- } -- -- np = dev_pm_opp_of_get_opp_desc_node(cpu_dev); -- if (!np) -- return -ENOENT; -- -- ret = of_device_is_compatible(np, "operating-points-v2-kryo-cpu"); -- if (!ret) { -- of_node_put(np); -- return -ENOENT; -- } -- -- speedbin_nvmem = of_nvmem_cell_get(np, NULL); -- of_node_put(np); -- if (IS_ERR(speedbin_nvmem)) { -- if (PTR_ERR(speedbin_nvmem) != -EPROBE_DEFER) -- dev_err(cpu_dev, "Could not get nvmem cell: %ld\n", -- PTR_ERR(speedbin_nvmem)); -- return PTR_ERR(speedbin_nvmem); -- } -- -- speedbin = nvmem_cell_read(speedbin_nvmem, &len); -- nvmem_cell_put(speedbin_nvmem); -- if (IS_ERR(speedbin)) -- return PTR_ERR(speedbin); -- -- switch (msm8996_version) { -- case MSM8996_V3: -- versions = 1 << (unsigned int)(*speedbin); -- break; -- case MSM8996_SG: -- versions = 1 << ((unsigned int)(*speedbin) + 4); -- break; -- default: -- BUG(); -- break; -- } -- kfree(speedbin); -- -- opp_tables = kcalloc(num_possible_cpus(), sizeof(*opp_tables), GFP_KERNEL); -- if (!opp_tables) -- return -ENOMEM; -- -- for_each_possible_cpu(cpu) { -- cpu_dev = get_cpu_device(cpu); -- if (NULL == cpu_dev) { -- ret = -ENODEV; -- goto free_opp; -- } -- -- opp_tables[cpu] = dev_pm_opp_set_supported_hw(cpu_dev, -- &versions, 1); -- if (IS_ERR(opp_tables[cpu])) { -- ret = PTR_ERR(opp_tables[cpu]); -- dev_err(cpu_dev, "Failed to set supported hardware\n"); -- goto free_opp; -- } -- } -- -- cpufreq_dt_pdev = platform_device_register_simple("cpufreq-dt", -1, -- NULL, 0); -- if (!IS_ERR(cpufreq_dt_pdev)) { -- platform_set_drvdata(pdev, opp_tables); -- return 0; -- } -- -- ret = PTR_ERR(cpufreq_dt_pdev); -- dev_err(cpu_dev, "Failed to register platform device\n"); -- --free_opp: -- for_each_possible_cpu(cpu) { -- if (IS_ERR_OR_NULL(opp_tables[cpu])) -- break; -- dev_pm_opp_put_supported_hw(opp_tables[cpu]); -- } -- kfree(opp_tables); -- -- return ret; --} -- --static int qcom_cpufreq_kryo_remove(struct platform_device *pdev) --{ -- struct opp_table **opp_tables = platform_get_drvdata(pdev); -- unsigned int cpu; -- -- platform_device_unregister(cpufreq_dt_pdev); -- -- for_each_possible_cpu(cpu) -- dev_pm_opp_put_supported_hw(opp_tables[cpu]); -- -- kfree(opp_tables); -- -- return 0; --} -- --static struct platform_driver qcom_cpufreq_kryo_driver = { -- .probe = qcom_cpufreq_kryo_probe, -- .remove = qcom_cpufreq_kryo_remove, -- .driver = { -- .name = "qcom-cpufreq-kryo", -- }, --}; -- --static const struct of_device_id qcom_cpufreq_kryo_match_list[] __initconst = { -- { .compatible = "qcom,apq8096", }, -- { .compatible = "qcom,msm8996", }, -- {} --}; -- --/* -- * Since the driver depends on smem and nvmem drivers, which may -- * return EPROBE_DEFER, all the real activity is done in the probe, -- * which may be defered as well. The init here is only registering -- * the driver and the platform device. -- */ --static int __init qcom_cpufreq_kryo_init(void) --{ -- struct device_node *np = of_find_node_by_path("/"); -- const struct of_device_id *match; -- int ret; -- -- if (!np) -- return -ENODEV; -- -- match = of_match_node(qcom_cpufreq_kryo_match_list, np); -- of_node_put(np); -- if (!match) -- return -ENODEV; -- -- ret = platform_driver_register(&qcom_cpufreq_kryo_driver); -- if (unlikely(ret < 0)) -- return ret; -- -- kryo_cpufreq_pdev = platform_device_register_simple( -- "qcom-cpufreq-kryo", -1, NULL, 0); -- ret = PTR_ERR_OR_ZERO(kryo_cpufreq_pdev); -- if (0 == ret) -- return 0; -- -- platform_driver_unregister(&qcom_cpufreq_kryo_driver); -- return ret; --} --module_init(qcom_cpufreq_kryo_init); -- --static void __exit qcom_cpufreq_kryo_exit(void) --{ -- platform_device_unregister(kryo_cpufreq_pdev); -- platform_driver_unregister(&qcom_cpufreq_kryo_driver); --} --module_exit(qcom_cpufreq_kryo_exit); -- --MODULE_DESCRIPTION("Qualcomm Technologies, Inc. Kryo CPUfreq driver"); --MODULE_LICENSE("GPL v2"); ---- /dev/null -+++ b/drivers/cpufreq/qcom-cpufreq-nvmem.c -@@ -0,0 +1,273 @@ -+// SPDX-License-Identifier: GPL-2.0 -+/* -+ * Copyright (c) 2018, The Linux Foundation. All rights reserved. -+ */ -+ -+/* -+ * In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO processors, -+ * the CPU frequency subset and voltage value of each OPP varies -+ * based on the silicon variant in use. Qualcomm Process Voltage Scaling Tables -+ * defines the voltage and frequency value based on the msm-id in SMEM -+ * and speedbin blown in the efuse combination. -+ * The qcom-cpufreq-nvmem driver reads the msm-id and efuse value from the SoC -+ * to provide the OPP framework with required information. -+ * This is used to determine the voltage and frequency value for each OPP of -+ * operating-points-v2 table when it is parsed by the OPP framework. -+ */ -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#define MSM_ID_SMEM 137 -+ -+enum _msm_id { -+ MSM8996V3 = 0xF6ul, -+ APQ8096V3 = 0x123ul, -+ MSM8996SG = 0x131ul, -+ APQ8096SG = 0x138ul, -+}; -+ -+enum _msm8996_version { -+ MSM8996_V3, -+ MSM8996_SG, -+ NUM_OF_MSM8996_VERSIONS, -+}; -+ -+static struct platform_device *cpufreq_dt_pdev, *cpufreq_pdev; -+ -+static enum _msm8996_version qcom_cpufreq_get_msm_id(void) -+{ -+ size_t len; -+ u32 *msm_id; -+ enum _msm8996_version version; -+ -+ msm_id = qcom_smem_get(QCOM_SMEM_HOST_ANY, MSM_ID_SMEM, &len); -+ if (IS_ERR(msm_id)) -+ return NUM_OF_MSM8996_VERSIONS; -+ -+ /* The first 4 bytes are format, next to them is the actual msm-id */ -+ msm_id++; -+ -+ switch ((enum _msm_id)*msm_id) { -+ case MSM8996V3: -+ case APQ8096V3: -+ version = MSM8996_V3; -+ break; -+ case MSM8996SG: -+ case APQ8096SG: -+ version = MSM8996_SG; -+ break; -+ default: -+ version = NUM_OF_MSM8996_VERSIONS; -+ } -+ -+ return version; -+} -+ -+static int qcom_cpufreq_kryo_name_version(struct device *cpu_dev, -+ struct nvmem_cell *speedbin_nvmem, -+ u32 *versions) -+{ -+ size_t len; -+ u8 *speedbin; -+ enum _msm8996_version msm8996_version; -+ -+ msm8996_version = qcom_cpufreq_get_msm_id(); -+ if (NUM_OF_MSM8996_VERSIONS == msm8996_version) { -+ dev_err(cpu_dev, "Not Snapdragon 820/821!"); -+ return -ENODEV; -+ } -+ -+ speedbin = nvmem_cell_read(speedbin_nvmem, &len); -+ if (IS_ERR(speedbin)) -+ return PTR_ERR(speedbin); -+ -+ switch (msm8996_version) { -+ case MSM8996_V3: -+ *versions = 1 << (unsigned int)(*speedbin); -+ break; -+ case MSM8996_SG: -+ *versions = 1 << ((unsigned int)(*speedbin) + 4); -+ break; -+ default: -+ BUG(); -+ break; -+ } -+ -+ kfree(speedbin); -+ return 0; -+} -+ -+static int qcom_cpufreq_probe(struct platform_device *pdev) -+{ -+ struct opp_table **opp_tables; -+ int (*get_version)(struct device *cpu_dev, -+ struct nvmem_cell *speedbin_nvmem, -+ u32 *versions); -+ struct nvmem_cell *speedbin_nvmem; -+ struct device_node *np; -+ struct device *cpu_dev; -+ unsigned cpu; -+ u32 versions; -+ const struct of_device_id *match; -+ int ret; -+ -+ cpu_dev = get_cpu_device(0); -+ if (!cpu_dev) -+ return -ENODEV; -+ -+ match = pdev->dev.platform_data; -+ get_version = match->data; -+ if (!get_version) -+ return -ENODEV; -+ -+ np = dev_pm_opp_of_get_opp_desc_node(cpu_dev); -+ if (!np) -+ return -ENOENT; -+ -+ ret = of_device_is_compatible(np, "operating-points-v2-kryo-cpu"); -+ if (!ret) { -+ of_node_put(np); -+ return -ENOENT; -+ } -+ -+ speedbin_nvmem = of_nvmem_cell_get(np, NULL); -+ of_node_put(np); -+ if (IS_ERR(speedbin_nvmem)) { -+ if (PTR_ERR(speedbin_nvmem) != -EPROBE_DEFER) -+ dev_err(cpu_dev, "Could not get nvmem cell: %ld\n", -+ PTR_ERR(speedbin_nvmem)); -+ return PTR_ERR(speedbin_nvmem); -+ } -+ -+ ret = get_version(cpu_dev, speedbin_nvmem, &versions); -+ nvmem_cell_put(speedbin_nvmem); -+ if (ret) -+ return ret; -+ -+ opp_tables = kcalloc(num_possible_cpus(), sizeof(*opp_tables), GFP_KERNEL); -+ if (!opp_tables) -+ return -ENOMEM; -+ -+ for_each_possible_cpu(cpu) { -+ cpu_dev = get_cpu_device(cpu); -+ if (NULL == cpu_dev) { -+ ret = -ENODEV; -+ goto free_opp; -+ } -+ -+ opp_tables[cpu] = dev_pm_opp_set_supported_hw(cpu_dev, -+ &versions, 1); -+ if (IS_ERR(opp_tables[cpu])) { -+ ret = PTR_ERR(opp_tables[cpu]); -+ dev_err(cpu_dev, "Failed to set supported hardware\n"); -+ goto free_opp; -+ } -+ } -+ -+ cpufreq_dt_pdev = platform_device_register_simple("cpufreq-dt", -1, -+ NULL, 0); -+ if (!IS_ERR(cpufreq_dt_pdev)) { -+ platform_set_drvdata(pdev, opp_tables); -+ return 0; -+ } -+ -+ ret = PTR_ERR(cpufreq_dt_pdev); -+ dev_err(cpu_dev, "Failed to register platform device\n"); -+ -+free_opp: -+ for_each_possible_cpu(cpu) { -+ if (IS_ERR_OR_NULL(opp_tables[cpu])) -+ break; -+ dev_pm_opp_put_supported_hw(opp_tables[cpu]); -+ } -+ kfree(opp_tables); -+ -+ return ret; -+} -+ -+static int qcom_cpufreq_remove(struct platform_device *pdev) -+{ -+ struct opp_table **opp_tables = platform_get_drvdata(pdev); -+ unsigned int cpu; -+ -+ platform_device_unregister(cpufreq_dt_pdev); -+ -+ for_each_possible_cpu(cpu) -+ dev_pm_opp_put_supported_hw(opp_tables[cpu]); -+ -+ kfree(opp_tables); -+ -+ return 0; -+} -+ -+static struct platform_driver qcom_cpufreq_driver = { -+ .probe = qcom_cpufreq_probe, -+ .remove = qcom_cpufreq_remove, -+ .driver = { -+ .name = "qcom-cpufreq-nvmem", -+ }, -+}; -+ -+static const struct of_device_id qcom_cpufreq_match_list[] __initconst = { -+ { .compatible = "qcom,apq8096", -+ .data = qcom_cpufreq_kryo_name_version }, -+ { .compatible = "qcom,msm8996", -+ .data = qcom_cpufreq_kryo_name_version }, -+ {}, -+}; -+ -+/* -+ * Since the driver depends on smem and nvmem drivers, which may -+ * return EPROBE_DEFER, all the real activity is done in the probe, -+ * which may be defered as well. The init here is only registering -+ * the driver and the platform device. -+ */ -+static int __init qcom_cpufreq_init(void) -+{ -+ struct device_node *np = of_find_node_by_path("/"); -+ const struct of_device_id *match; -+ int ret; -+ -+ if (!np) -+ return -ENODEV; -+ -+ match = of_match_node(qcom_cpufreq_match_list, np); -+ of_node_put(np); -+ if (!match) -+ return -ENODEV; -+ -+ ret = platform_driver_register(&qcom_cpufreq_driver); -+ if (unlikely(ret < 0)) -+ return ret; -+ -+ cpufreq_pdev = platform_device_register_data(NULL, "qcom-cpufreq-nvmem", -+ -1, match, sizeof(*match)); -+ ret = PTR_ERR_OR_ZERO(cpufreq_pdev); -+ if (0 == ret) -+ return 0; -+ -+ platform_driver_unregister(&qcom_cpufreq_driver); -+ return ret; -+} -+module_init(qcom_cpufreq_init); -+ -+static void __exit qcom_cpufreq_exit(void) -+{ -+ platform_device_unregister(cpufreq_pdev); -+ platform_driver_unregister(&qcom_cpufreq_driver); -+} -+module_exit(qcom_cpufreq_exit); -+ -+MODULE_DESCRIPTION("Qualcomm Technologies, Inc. CPUfreq driver"); -+MODULE_LICENSE("GPL v2"); diff --git a/target/linux/ipq806x/patches-4.19/0037-qcom-cpufreq-nvmem-Refactor-the-driver.patch b/target/linux/ipq806x/patches-4.19/0037-qcom-cpufreq-nvmem-Refactor-the-driver.patch deleted file mode 100644 index d00b2ccfcb..0000000000 --- a/target/linux/ipq806x/patches-4.19/0037-qcom-cpufreq-nvmem-Refactor-the-driver.patch +++ /dev/null @@ -1,241 +0,0 @@ -From 57f2f8b4aa0c6b41a284da82bfa40dc3b2abe9a5 Mon Sep 17 00:00:00 2001 -From: Niklas Cassel -Date: Thu, 25 Jul 2019 12:41:33 +0200 -Subject: [PATCH] cpufreq: qcom: Refactor the driver to make it easier to - extend - -Refactor the driver to make it easier to extend in a later commit. - -Create a driver struct to collect all common resources, in order to make -it easier to free up all common resources. -Create a driver match_data struct to make it easier to extend the driver -with support for new features that might only be supported on certain SoCs. - -Co-developed-by: Jorge Ramirez-Ortiz -Signed-off-by: Jorge Ramirez-Ortiz -Signed-off-by: Niklas Cassel -Reviewed-by: Ilia Lin -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/qcom-cpufreq-nvmem.c | 123 +++++++++++++++++---------- - 1 file changed, 79 insertions(+), 44 deletions(-) - ---- a/drivers/cpufreq/qcom-cpufreq-nvmem.c -+++ b/drivers/cpufreq/qcom-cpufreq-nvmem.c -@@ -43,6 +43,20 @@ enum _msm8996_version { - NUM_OF_MSM8996_VERSIONS, - }; - -+struct qcom_cpufreq_drv; -+ -+struct qcom_cpufreq_match_data { -+ int (*get_version)(struct device *cpu_dev, -+ struct nvmem_cell *speedbin_nvmem, -+ struct qcom_cpufreq_drv *drv); -+}; -+ -+struct qcom_cpufreq_drv { -+ struct opp_table **opp_tables; -+ u32 versions; -+ const struct qcom_cpufreq_match_data *data; -+}; -+ - static struct platform_device *cpufreq_dt_pdev, *cpufreq_pdev; - - static enum _msm8996_version qcom_cpufreq_get_msm_id(void) -@@ -76,7 +90,7 @@ static enum _msm8996_version qcom_cpufre - - static int qcom_cpufreq_kryo_name_version(struct device *cpu_dev, - struct nvmem_cell *speedbin_nvmem, -- u32 *versions) -+ struct qcom_cpufreq_drv *drv) - { - size_t len; - u8 *speedbin; -@@ -94,10 +108,10 @@ static int qcom_cpufreq_kryo_name_versio - - switch (msm8996_version) { - case MSM8996_V3: -- *versions = 1 << (unsigned int)(*speedbin); -+ drv->versions = 1 << (unsigned int)(*speedbin); - break; - case MSM8996_SG: -- *versions = 1 << ((unsigned int)(*speedbin) + 4); -+ drv->versions = 1 << ((unsigned int)(*speedbin) + 4); - break; - default: - BUG(); -@@ -108,17 +122,17 @@ static int qcom_cpufreq_kryo_name_versio - return 0; - } - -+static const struct qcom_cpufreq_match_data match_data_kryo = { -+ .get_version = qcom_cpufreq_kryo_name_version, -+}; -+ - static int qcom_cpufreq_probe(struct platform_device *pdev) - { -- struct opp_table **opp_tables; -- int (*get_version)(struct device *cpu_dev, -- struct nvmem_cell *speedbin_nvmem, -- u32 *versions); -+ struct qcom_cpufreq_drv *drv; - struct nvmem_cell *speedbin_nvmem; - struct device_node *np; - struct device *cpu_dev; - unsigned cpu; -- u32 versions; - const struct of_device_id *match; - int ret; - -@@ -126,11 +140,6 @@ static int qcom_cpufreq_probe(struct pla - if (!cpu_dev) - return -ENODEV; - -- match = pdev->dev.platform_data; -- get_version = match->data; -- if (!get_version) -- return -ENODEV; -- - np = dev_pm_opp_of_get_opp_desc_node(cpu_dev); - if (!np) - return -ENOENT; -@@ -141,23 +150,43 @@ static int qcom_cpufreq_probe(struct pla - return -ENOENT; - } - -- speedbin_nvmem = of_nvmem_cell_get(np, NULL); -- of_node_put(np); -- if (IS_ERR(speedbin_nvmem)) { -- if (PTR_ERR(speedbin_nvmem) != -EPROBE_DEFER) -- dev_err(cpu_dev, "Could not get nvmem cell: %ld\n", -- PTR_ERR(speedbin_nvmem)); -- return PTR_ERR(speedbin_nvmem); -+ drv = kzalloc(sizeof(*drv), GFP_KERNEL); -+ if (!drv) -+ return -ENOMEM; -+ -+ match = pdev->dev.platform_data; -+ drv->data = match->data; -+ if (!drv->data) { -+ ret = -ENODEV; -+ goto free_drv; - } - -- ret = get_version(cpu_dev, speedbin_nvmem, &versions); -- nvmem_cell_put(speedbin_nvmem); -- if (ret) -- return ret; -+ if (drv->data->get_version) { -+ speedbin_nvmem = of_nvmem_cell_get(np, NULL); -+ if (IS_ERR(speedbin_nvmem)) { -+ if (PTR_ERR(speedbin_nvmem) != -EPROBE_DEFER) -+ dev_err(cpu_dev, -+ "Could not get nvmem cell: %ld\n", -+ PTR_ERR(speedbin_nvmem)); -+ ret = PTR_ERR(speedbin_nvmem); -+ goto free_drv; -+ } - -- opp_tables = kcalloc(num_possible_cpus(), sizeof(*opp_tables), GFP_KERNEL); -- if (!opp_tables) -- return -ENOMEM; -+ ret = drv->data->get_version(cpu_dev, speedbin_nvmem, drv); -+ if (ret) { -+ nvmem_cell_put(speedbin_nvmem); -+ goto free_drv; -+ } -+ nvmem_cell_put(speedbin_nvmem); -+ } -+ of_node_put(np); -+ -+ drv->opp_tables = kcalloc(num_possible_cpus(), sizeof(*drv->opp_tables), -+ GFP_KERNEL); -+ if (!drv->opp_tables) { -+ ret = -ENOMEM; -+ goto free_drv; -+ } - - for_each_possible_cpu(cpu) { - cpu_dev = get_cpu_device(cpu); -@@ -166,19 +195,23 @@ static int qcom_cpufreq_probe(struct pla - goto free_opp; - } - -- opp_tables[cpu] = dev_pm_opp_set_supported_hw(cpu_dev, -- &versions, 1); -- if (IS_ERR(opp_tables[cpu])) { -- ret = PTR_ERR(opp_tables[cpu]); -- dev_err(cpu_dev, "Failed to set supported hardware\n"); -- goto free_opp; -+ if (drv->data->get_version) { -+ drv->opp_tables[cpu] = -+ dev_pm_opp_set_supported_hw(cpu_dev, -+ &drv->versions, 1); -+ if (IS_ERR(drv->opp_tables[cpu])) { -+ ret = PTR_ERR(drv->opp_tables[cpu]); -+ dev_err(cpu_dev, -+ "Failed to set supported hardware\n"); -+ goto free_opp; -+ } - } - } - - cpufreq_dt_pdev = platform_device_register_simple("cpufreq-dt", -1, - NULL, 0); - if (!IS_ERR(cpufreq_dt_pdev)) { -- platform_set_drvdata(pdev, opp_tables); -+ platform_set_drvdata(pdev, drv); - return 0; - } - -@@ -187,26 +220,30 @@ static int qcom_cpufreq_probe(struct pla - - free_opp: - for_each_possible_cpu(cpu) { -- if (IS_ERR_OR_NULL(opp_tables[cpu])) -+ if (IS_ERR_OR_NULL(drv->opp_tables[cpu])) - break; -- dev_pm_opp_put_supported_hw(opp_tables[cpu]); -+ dev_pm_opp_put_supported_hw(drv->opp_tables[cpu]); - } -- kfree(opp_tables); -+ kfree(drv->opp_tables); -+free_drv: -+ kfree(drv); - - return ret; - } - - static int qcom_cpufreq_remove(struct platform_device *pdev) - { -- struct opp_table **opp_tables = platform_get_drvdata(pdev); -+ struct qcom_cpufreq_drv *drv = platform_get_drvdata(pdev); - unsigned int cpu; - - platform_device_unregister(cpufreq_dt_pdev); - - for_each_possible_cpu(cpu) -- dev_pm_opp_put_supported_hw(opp_tables[cpu]); -+ if (drv->opp_tables[cpu]) -+ dev_pm_opp_put_supported_hw(drv->opp_tables[cpu]); - -- kfree(opp_tables); -+ kfree(drv->opp_tables); -+ kfree(drv); - - return 0; - } -@@ -220,10 +257,8 @@ static struct platform_driver qcom_cpufr - }; - - static const struct of_device_id qcom_cpufreq_match_list[] __initconst = { -- { .compatible = "qcom,apq8096", -- .data = qcom_cpufreq_kryo_name_version }, -- { .compatible = "qcom,msm8996", -- .data = qcom_cpufreq_kryo_name_version }, -+ { .compatible = "qcom,apq8096", .data = &match_data_kryo }, -+ { .compatible = "qcom,msm8996", .data = &match_data_kryo }, - {}, - }; - diff --git a/target/linux/ipq806x/patches-4.19/0038-qcom-cpufreq-nvmem-Add-support-for-krait-based-socs.patch b/target/linux/ipq806x/patches-4.19/0038-qcom-cpufreq-nvmem-Add-support-for-krait-based-socs.patch deleted file mode 100644 index b8895231d8..0000000000 --- a/target/linux/ipq806x/patches-4.19/0038-qcom-cpufreq-nvmem-Add-support-for-krait-based-socs.patch +++ /dev/null @@ -1,345 +0,0 @@ -Subject: [PATCH v12 14/14] cpufreq: qcom: Add support for krait based socs -Date: Tue, 14 Aug 2018 17:42:33 +0530 -Message-Id: <1534248753-2440-15-git-send-email-sricharan@codeaurora.org> -X-Mailer: git-send-email 1.9.1 -In-Reply-To: <1534248753-2440-1-git-send-email-sricharan@codeaurora.org> -References: <1534248753-2440-1-git-send-email-sricharan@codeaurora.org> -Sender: linux-kernel-owner@vger.kernel.org -Precedence: bulk -List-ID: -X-Mailing-List: linux-kernel@vger.kernel.org - -In Certain QCOM SoCs like ipq8064, apq8064, msm8960, msm8974 -that has KRAIT processors the voltage/current value of each OPP -varies based on the silicon variant in use. - -The required OPP related data is determined based on -the efuse value. This is similar to the existing code for -kryo cores. So adding support for krait cores here. - -Signed-off-by: Sricharan R ---- - .../devicetree/bindings/opp/qcom-nvmem-cpufreq.txt | 3 +- - drivers/cpufreq/Kconfig.arm | 2 +- - drivers/cpufreq/cpufreq-dt-platdev.c | 5 + - drivers/cpufreq/qcom-cpufreq-nvmem.c | 151 +++++++++++++++++++-- - 4 files changed, 149 insertions(+), 12 deletions(-) - -# diff --git a/Documentation/devicetree/bindings/opp/qcom-nvmem-cpufreq.txt b/Documentation/devicetree/bindings/opp/qcom-nvmem-cpufreq.txt -# index 6dcdfcd..7bc0f1a 100644 -# --- a/Documentation/devicetree/bindings/opp/qcom-nvmem-cpufreq.txt -# +++ b/Documentation/devicetree/bindings/opp/qcom-nvmem-cpufreq.txt -# @@ -19,7 +19,8 @@ In 'cpus' nodes: - -# In 'operating-points-v2' table: -# - compatible: Should be -# - - 'operating-points-v2-qcom-cpu' for apq8096 and msm8996. -# + - 'operating-points-v2-qcom-cpu' for apq8096, msm8996, msm8974, -# + apq8064, msm8960 and ipq8074. -# - nvmem-cells: A phandle pointing to a nvmem-cells node representing the -# efuse registers that has information about the -# speedbin that is used to select the right frequency/voltage ---- a/drivers/cpufreq/Kconfig.arm -+++ b/drivers/cpufreq/Kconfig.arm -@@ -112,7 +112,7 @@ config ARM_OMAP2PLUS_CPUFREQ - - config ARM_QCOM_CPUFREQ_NVMEM - tristate "Qualcomm nvmem based CPUFreq" -- depends on ARM64 -+ depends on ARCH_QCOM - depends on QCOM_QFPROM - depends on QCOM_SMEM - select PM_OPP ---- a/drivers/cpufreq/cpufreq-dt-platdev.c -+++ b/drivers/cpufreq/cpufreq-dt-platdev.c -@@ -128,6 +128,11 @@ static const struct of_device_id blackli - { .compatible = "ti,am43", }, - { .compatible = "ti,dra7", }, - -+ { .compatible = "qcom,ipq8064", }, -+ { .compatible = "qcom,apq8064", }, -+ { .compatible = "qcom,msm8974", }, -+ { .compatible = "qcom,msm8960", }, -+ - { } - }; - ---- a/drivers/cpufreq/qcom-cpufreq-nvmem.c -+++ b/drivers/cpufreq/qcom-cpufreq-nvmem.c -@@ -48,17 +48,92 @@ struct qcom_cpufreq_drv; - struct qcom_cpufreq_match_data { - int (*get_version)(struct device *cpu_dev, - struct nvmem_cell *speedbin_nvmem, -+ char **pvs_name, - struct qcom_cpufreq_drv *drv); - }; - - struct qcom_cpufreq_drv { -- struct opp_table **opp_tables; -+ struct opp_table **opp_tables1; -+ struct opp_table **opp_tables2; - u32 versions; - const struct qcom_cpufreq_match_data *data; - }; - - static struct platform_device *cpufreq_dt_pdev, *cpufreq_pdev; - -+static void get_krait_bin_format_a(int *speed, int *pvs, int *pvs_ver, -+ struct nvmem_cell *pvs_nvmem, u8 *buf) -+{ -+ u32 pte_efuse; -+ -+ pte_efuse = *((u32 *)buf); -+ -+ *speed = pte_efuse & 0xf; -+ if (*speed == 0xf) -+ *speed = (pte_efuse >> 4) & 0xf; -+ -+ if (*speed == 0xf) { -+ *speed = 0; -+ pr_warn("Speed bin: Defaulting to %d\n", *speed); -+ } else { -+ pr_info("Speed bin: %d\n", *speed); -+ } -+ -+ *pvs = (pte_efuse >> 10) & 0x7; -+ if (*pvs == 0x7) -+ *pvs = (pte_efuse >> 13) & 0x7; -+ -+ if (*pvs == 0x7) { -+ *pvs = 0; -+ pr_warn("PVS bin: Defaulting to %d\n", *pvs); -+ } else { -+ pr_info("PVS bin: %d\n", *pvs); -+ } -+} -+ -+static void get_krait_bin_format_b(int *speed, int *pvs, int *pvs_ver, -+ struct nvmem_cell *pvs_nvmem, u8 *buf) -+{ -+ u32 pte_efuse, redundant_sel; -+ -+ pte_efuse = *((u32 *)buf); -+ redundant_sel = (pte_efuse >> 24) & 0x7; -+ *speed = pte_efuse & 0x7; -+ -+ /* 4 bits of PVS are in efuse register bits 31, 8-6. */ -+ *pvs = ((pte_efuse >> 28) & 0x8) | ((pte_efuse >> 6) & 0x7); -+ *pvs_ver = (pte_efuse >> 4) & 0x3; -+ -+ switch (redundant_sel) { -+ case 1: -+ *speed = (pte_efuse >> 27) & 0xf; -+ break; -+ case 2: -+ *pvs = (pte_efuse >> 27) & 0xf; -+ break; -+ } -+ -+ /* Check SPEED_BIN_BLOW_STATUS */ -+ if (pte_efuse & BIT(3)) { -+ pr_info("Speed bin: %d\n", *speed); -+ } else { -+ pr_warn("Speed bin not set. Defaulting to 0!\n"); -+ *speed = 0; -+ } -+ -+ /* Check PVS_BLOW_STATUS */ -+ pte_efuse = *(((u32 *)buf) + 4); -+ pte_efuse &= BIT(21); -+ if (pte_efuse) { -+ pr_info("PVS bin: %d\n", *pvs); -+ } else { -+ pr_warn("PVS bin not set. Defaulting to 0!\n"); -+ *pvs = 0; -+ } -+ -+ pr_info("PVS version: %d\n", *pvs_ver); -+} -+ - static enum _msm8996_version qcom_cpufreq_get_msm_id(void) - { - size_t len; -@@ -90,11 +165,13 @@ static enum _msm8996_version qcom_cpufre - - static int qcom_cpufreq_kryo_name_version(struct device *cpu_dev, - struct nvmem_cell *speedbin_nvmem, -+ char **pvs_name, - struct qcom_cpufreq_drv *drv) - { - size_t len; - u8 *speedbin; - enum _msm8996_version msm8996_version; -+ *pvs_name = NULL; - - msm8996_version = qcom_cpufreq_get_msm_id(); - if (NUM_OF_MSM8996_VERSIONS == msm8996_version) { -@@ -122,16 +199,51 @@ static int qcom_cpufreq_kryo_name_versio - return 0; - } - -+static int qcom_cpufreq_krait_name_version(struct device *cpu_dev, -+ struct nvmem_cell *speedbin_nvmem, -+ char **pvs_name, -+ struct qcom_cpufreq_drv *drv) -+{ -+ int speed = 0, pvs = 0, pvs_ver = 0; -+ u8 *speedbin; -+ size_t len; -+ -+ speedbin = nvmem_cell_read(speedbin_nvmem, &len); -+ if (len == 4) { -+ get_krait_bin_format_a(&speed, &pvs, &pvs_ver, -+ speedbin_nvmem, speedbin); -+ } else if (len == 8) { -+ get_krait_bin_format_b(&speed, &pvs, &pvs_ver, -+ speedbin_nvmem, speedbin); -+ } else { -+ dev_err(cpu_dev, "Unable to read nvmem data. Defaulting to 0!\n"); -+ return -ENODEV; -+ } -+ -+ snprintf(*pvs_name, sizeof("speedXX-pvsXX-vXX"), "speed%d-pvs%d-v%d", -+ speed, pvs, pvs_ver); -+ -+ drv->versions = (1 << speed); -+ -+ kfree(speedbin); -+ return 0; -+} -+ - static const struct qcom_cpufreq_match_data match_data_kryo = { - .get_version = qcom_cpufreq_kryo_name_version, - }; - -+static const struct qcom_cpufreq_match_data match_data_krait = { -+ .get_version = qcom_cpufreq_krait_name_version, -+}; -+ - static int qcom_cpufreq_probe(struct platform_device *pdev) - { - struct qcom_cpufreq_drv *drv; - struct nvmem_cell *speedbin_nvmem; - struct device_node *np; - struct device *cpu_dev; -+ char *pvs_name = "speedXX-pvsXX-vXX"; - unsigned cpu; - const struct of_device_id *match; - int ret; -@@ -144,7 +256,7 @@ static int qcom_cpufreq_probe(struct pla - if (!np) - return -ENOENT; - -- ret = of_device_is_compatible(np, "operating-points-v2-kryo-cpu"); -+ ret = of_device_is_compatible(np, "operating-points-v2-qcom-cpu"); - if (!ret) { - of_node_put(np); - return -ENOENT; -@@ -172,7 +284,7 @@ static int qcom_cpufreq_probe(struct pla - goto free_drv; - } - -- ret = drv->data->get_version(cpu_dev, speedbin_nvmem, drv); -+ ret = drv->data->get_version(cpu_dev, speedbin_nvmem, &pvs_name, drv); - if (ret) { - nvmem_cell_put(speedbin_nvmem); - goto free_drv; -@@ -181,12 +293,18 @@ static int qcom_cpufreq_probe(struct pla - } - of_node_put(np); - -- drv->opp_tables = kcalloc(num_possible_cpus(), sizeof(*drv->opp_tables), -+ drv->opp_tables1 = kcalloc(num_possible_cpus(), sizeof(*drv->opp_tables1), - GFP_KERNEL); -- if (!drv->opp_tables) { -+ if (!drv->opp_tables1) { - ret = -ENOMEM; - goto free_drv; - } -+ drv->opp_tables2 = kcalloc(num_possible_cpus(), sizeof(*drv->opp_tables2), -+ GFP_KERNEL); -+ if (!drv->opp_tables2) { -+ ret = -ENOMEM; -+ goto free_opp1; -+ } - - for_each_possible_cpu(cpu) { - cpu_dev = get_cpu_device(cpu); -@@ -196,11 +314,22 @@ static int qcom_cpufreq_probe(struct pla - } - - if (drv->data->get_version) { -- drv->opp_tables[cpu] = -- dev_pm_opp_set_supported_hw(cpu_dev, -+ -+ if (pvs_name) { -+ drv->opp_tables1[cpu] = dev_pm_opp_set_prop_name(cpu_dev, -+ pvs_name); -+ if (IS_ERR(drv->opp_tables1[cpu])) { -+ ret = PTR_ERR(drv->opp_tables1[cpu]); -+ dev_err(cpu_dev, "Failed to add OPP name %s\n", -+ pvs_name); -+ goto free_opp; -+ } -+ } -+ -+ drv->opp_tables2[cpu] = dev_pm_opp_set_supported_hw(cpu_dev, - &drv->versions, 1); -- if (IS_ERR(drv->opp_tables[cpu])) { -- ret = PTR_ERR(drv->opp_tables[cpu]); -+ if (IS_ERR(drv->opp_tables2[cpu])) { -+ ret = PTR_ERR(drv->opp_tables2[cpu]); - dev_err(cpu_dev, - "Failed to set supported hardware\n"); - goto free_opp; -@@ -220,11 +349,18 @@ static int qcom_cpufreq_probe(struct pla - - free_opp: - for_each_possible_cpu(cpu) { -- if (IS_ERR_OR_NULL(drv->opp_tables[cpu])) -+ if (IS_ERR_OR_NULL(drv->opp_tables1[cpu])) - break; -- dev_pm_opp_put_supported_hw(drv->opp_tables[cpu]); -+ dev_pm_opp_put_prop_name(drv->opp_tables1[cpu]); - } -- kfree(drv->opp_tables); -+ for_each_possible_cpu(cpu) { -+ if (IS_ERR_OR_NULL(drv->opp_tables2[cpu])) -+ break; -+ dev_pm_opp_put_supported_hw(drv->opp_tables2[cpu]); -+ } -+ kfree(drv->opp_tables2); -+free_opp1: -+ kfree(drv->opp_tables1); - free_drv: - kfree(drv); - -@@ -239,10 +375,14 @@ static int qcom_cpufreq_remove(struct pl - platform_device_unregister(cpufreq_dt_pdev); - - for_each_possible_cpu(cpu) -- if (drv->opp_tables[cpu]) -- dev_pm_opp_put_supported_hw(drv->opp_tables[cpu]); -+ if (drv->opp_tables1[cpu]) -+ dev_pm_opp_put_prop_name(drv->opp_tables1[cpu]); -+ for_each_possible_cpu(cpu) -+ if (drv->opp_tables2[cpu]) -+ dev_pm_opp_put_supported_hw(drv->opp_tables2[cpu]); - -- kfree(drv->opp_tables); -+ kfree(drv->opp_tables1); -+ kfree(drv->opp_tables2); - kfree(drv); - - return 0; -@@ -259,6 +399,10 @@ static struct platform_driver qcom_cpufr - static const struct of_device_id qcom_cpufreq_match_list[] __initconst = { - { .compatible = "qcom,apq8096", .data = &match_data_kryo }, - { .compatible = "qcom,msm8996", .data = &match_data_kryo }, -+ { .compatible = "qcom,ipq8064", .data = &match_data_krait }, -+ { .compatible = "qcom,apq8064", .data = &match_data_krait }, -+ { .compatible = "qcom,msm8974", .data = &match_data_krait }, -+ { .compatible = "qcom,msm8960", .data = &match_data_krait }, - {}, - }; - diff --git a/target/linux/ipq806x/patches-4.19/0049-PM-OPP-Support-adjusting-OPP-voltages-at-runtime.patch b/target/linux/ipq806x/patches-4.19/0049-PM-OPP-Support-adjusting-OPP-voltages-at-runtime.patch deleted file mode 100644 index c1cf02e747..0000000000 --- a/target/linux/ipq806x/patches-4.19/0049-PM-OPP-Support-adjusting-OPP-voltages-at-runtime.patch +++ /dev/null @@ -1,153 +0,0 @@ -From: Sylwester Nawrocki -To: krzk@kernel.org, vireshk@kernel.org, robh+dt@kernel.org -Cc: sboyd@kernel.org, roger.lu@mediatek.com, - linux-pm@vger.kernel.org, linux-arm-kernel@lists.infradead.org, - linux-samsung-soc@vger.kernel.org, devicetree@vger.kernel.org, - b.zolnierkie@samsung.com, m.szyprowski@samsung.com, - Stephen Boyd , - Sylwester Nawrocki -Subject: [PATCH v5 1/4] PM / OPP: Support adjusting OPP voltages at runtime -Date: Wed, 16 Oct 2019 16:57:53 +0200 -Message-ID: <20191016145756.16004-2-s.nawrocki@samsung.com> (raw) -In-Reply-To: <20191016145756.16004-1-s.nawrocki@samsung.com> - -From: Stephen Boyd - -On some SoCs the Adaptive Voltage Scaling (AVS) technique is -employed to optimize the operating voltage of a device. At a -given frequency, the hardware monitors dynamic factors and either -makes a suggestion for how much to adjust a voltage for the -current frequency, or it automatically adjusts the voltage -without software intervention. Add an API to the OPP library for -the former case, so that AVS type devices can update the voltages -for an OPP when the hardware determines the voltage should -change. The assumption is that drivers like CPUfreq or devfreq -will register for the OPP notifiers and adjust the voltage -according to suggestions that AVS makes. - -This patch is derived from [1] submitted by Stephen. -[1] https://lore.kernel.org/patchwork/patch/599279/ - -Signed-off-by: Stephen Boyd -Signed-off-by: Roger Lu -[s.nawrocki@samsung.com: added handling of OPP min/max voltage] -Signed-off-by: Sylwester Nawrocki ---- - drivers/opp/core.c | 69 ++++++++++++++++++++++++++++++++++++++++++ - include/linux/pm_opp.h | 13 ++++++++ - 2 files changed, 82 insertions(+) - ---- a/drivers/opp/core.c -+++ b/drivers/opp/core.c -@@ -1629,6 +1629,75 @@ put_table: - } - - /** -+ * dev_pm_opp_adjust_voltage() - helper to change the voltage of an OPP -+ * @dev: device for which we do this operation -+ * @freq: OPP frequency to adjust voltage of -+ * @u_volt: new OPP target voltage -+ * @u_volt_min: new OPP min voltage -+ * @u_volt_max: new OPP max voltage -+ * -+ * Return: -EINVAL for bad pointers, -ENOMEM if no memory available for the -+ * copy operation, returns 0 if no modifcation was done OR modification was -+ * successful. -+ */ -+int dev_pm_opp_adjust_voltage(struct device *dev, unsigned long freq, -+ unsigned long u_volt, unsigned long u_volt_min, -+ unsigned long u_volt_max) -+ -+{ -+ struct opp_table *opp_table; -+ struct dev_pm_opp *tmp_opp, *opp = ERR_PTR(-ENODEV); -+ int r = 0; -+ -+ /* Find the opp_table */ -+ opp_table = _find_opp_table(dev); -+ if (IS_ERR(opp_table)) { -+ r = PTR_ERR(opp_table); -+ dev_warn(dev, "%s: Device OPP not found (%d)\n", __func__, r); -+ return r; -+ } -+ -+ mutex_lock(&opp_table->lock); -+ -+ /* Do we have the frequency? */ -+ list_for_each_entry(tmp_opp, &opp_table->opp_list, node) { -+ if (tmp_opp->rate == freq) { -+ opp = tmp_opp; -+ break; -+ } -+ } -+ -+ if (IS_ERR(opp)) { -+ r = PTR_ERR(opp); -+ goto adjust_unlock; -+ } -+ -+ /* Is update really needed? */ -+ if (opp->supplies->u_volt == u_volt) -+ goto adjust_unlock; -+ -+ opp->supplies->u_volt = u_volt; -+ opp->supplies->u_volt_min = u_volt_min; -+ opp->supplies->u_volt_max = u_volt_max; -+ -+ dev_pm_opp_get(opp); -+ mutex_unlock(&opp_table->lock); -+ -+ /* Notify the voltage change of the OPP */ -+ blocking_notifier_call_chain(&opp_table->head, OPP_EVENT_ADJUST_VOLTAGE, -+ opp); -+ -+ dev_pm_opp_put(opp); -+ goto adjust_put_table; -+ -+adjust_unlock: -+ mutex_unlock(&opp_table->lock); -+adjust_put_table: -+ dev_pm_opp_put_opp_table(opp_table); -+ return r; -+} -+ -+/** - * dev_pm_opp_enable() - Enable a specific OPP - * @dev: device for which we do this operation - * @freq: OPP frequency to enable ---- a/include/linux/pm_opp.h -+++ b/include/linux/pm_opp.h -@@ -25,6 +25,7 @@ struct opp_table; - - enum dev_pm_opp_event { - OPP_EVENT_ADD, OPP_EVENT_REMOVE, OPP_EVENT_ENABLE, OPP_EVENT_DISABLE, -+ OPP_EVENT_ADJUST_VOLTAGE, - }; - - /** -@@ -108,6 +109,10 @@ int dev_pm_opp_add(struct device *dev, u - unsigned long u_volt); - void dev_pm_opp_remove(struct device *dev, unsigned long freq); - -+int dev_pm_opp_adjust_voltage(struct device *dev, unsigned long freq, -+ unsigned long u_volt, unsigned long u_volt_min, -+ unsigned long u_volt_max); -+ - int dev_pm_opp_enable(struct device *dev, unsigned long freq); - - int dev_pm_opp_disable(struct device *dev, unsigned long freq); -@@ -208,6 +213,14 @@ static inline void dev_pm_opp_remove(str - { - } - -+static inline int -+dev_pm_opp_adjust_voltage(struct device *dev, unsigned long freq, -+ unsigned long u_volt, unsigned long u_volt_min, -+ unsigned long u_volt_max) -+{ -+ return 0; -+} -+ - static inline int dev_pm_opp_enable(struct device *dev, unsigned long freq) - { - return 0; diff --git a/target/linux/ipq806x/patches-4.19/0051-PM-OPP-Add-a-helper-to-get-an-opp-regulator-for-devi.patch b/target/linux/ipq806x/patches-4.19/0051-PM-OPP-Add-a-helper-to-get-an-opp-regulator-for-devi.patch deleted file mode 100644 index 4312db905a..0000000000 --- a/target/linux/ipq806x/patches-4.19/0051-PM-OPP-Add-a-helper-to-get-an-opp-regulator-for-devi.patch +++ /dev/null @@ -1,52 +0,0 @@ -From d06ca5e7a3cf726f5be5ffd96e93ccd798b8c09a Mon Sep 17 00:00:00 2001 -From: Georgi Djakov -Date: Thu, 12 May 2016 14:41:33 +0300 -Subject: [PATCH 51/69] PM / OPP: Add a helper to get an opp regulator for - device - -Signed-off-by: Georgi Djakov ---- - drivers/opp/core.c | 21 +++++++++++++++++++++ - include/linux/pm_opp.h | 1 + - 2 files changed, 22 insertions(+) - ---- a/drivers/opp/core.c -+++ b/drivers/opp/core.c -@@ -125,6 +125,27 @@ unsigned long dev_pm_opp_get_freq(struct - } - EXPORT_SYMBOL_GPL(dev_pm_opp_get_freq); - -+struct regulator *dev_pm_opp_get_regulator(struct device *dev) -+{ -+ struct opp_table *opp_table; -+ struct regulator *reg; -+ -+ rcu_read_lock(); -+ -+ opp_table = _find_opp_table(dev); -+ if (IS_ERR(opp_table)) { -+ rcu_read_unlock(); -+ return ERR_CAST(opp_table); -+ } -+ -+ reg = opp_table->regulators[0]; -+ -+ rcu_read_unlock(); -+ -+ return reg; -+} -+EXPORT_SYMBOL_GPL(dev_pm_opp_get_regulator); -+ - /** - * dev_pm_opp_is_turbo() - Returns if opp is turbo OPP or not - * @opp: opp for which turbo mode is being verified ---- a/include/linux/pm_opp.h -+++ b/include/linux/pm_opp.h -@@ -85,6 +85,7 @@ void dev_pm_opp_put_opp_table(struct opp - unsigned long dev_pm_opp_get_voltage(struct dev_pm_opp *opp); - - unsigned long dev_pm_opp_get_freq(struct dev_pm_opp *opp); -+struct regulator *dev_pm_opp_get_regulator(struct device *dev); - - bool dev_pm_opp_is_turbo(struct dev_pm_opp *opp); - diff --git a/target/linux/ipq806x/patches-4.19/0052-PM-OPP-Update-the-voltage-tolerance-when-adjusting-t.patch b/target/linux/ipq806x/patches-4.19/0052-PM-OPP-Update-the-voltage-tolerance-when-adjusting-t.patch deleted file mode 100644 index 9f0b9ec6d3..0000000000 --- a/target/linux/ipq806x/patches-4.19/0052-PM-OPP-Update-the-voltage-tolerance-when-adjusting-t.patch +++ /dev/null @@ -1,47 +0,0 @@ -From 4533c285c2aedce6d4434d7b877066de3b1ecb33 Mon Sep 17 00:00:00 2001 -From: Georgi Djakov -Date: Thu, 25 Aug 2016 18:43:35 +0300 -Subject: [PATCH 52/69] PM / OPP: Update the voltage tolerance when adjusting - the OPP - -When the voltage is adjusted, the voltage tolerance is not updated. -This can lead to situations where the voltage min value is greater -than the voltage max value. The final result is triggering a BUG() -in the regulator core. -Fix this by updating the voltage tolerance values too. - -Signed-off-by: Georgi Djakov ---- - drivers/opp/core.c | 5 +++++ - 1 file changed, 5 insertions(+) - ---- a/drivers/opp/core.c -+++ b/drivers/opp/core.c -@@ -1669,6 +1669,7 @@ int dev_pm_opp_adjust_voltage(struct dev - struct opp_table *opp_table; - struct dev_pm_opp *tmp_opp, *opp = ERR_PTR(-ENODEV); - int r = 0; -+ unsigned long tol; - - /* Find the opp_table */ - opp_table = _find_opp_table(dev); -@@ -1698,8 +1699,17 @@ int dev_pm_opp_adjust_voltage(struct dev - goto adjust_unlock; - - opp->supplies->u_volt = u_volt; -- opp->supplies->u_volt_min = u_volt_min; -- opp->supplies->u_volt_max = u_volt_max; -+ -+ tol = u_volt * opp_table->voltage_tolerance_v1 / 100; -+ if ( u_volt_min == u_volt ) -+ opp->supplies->u_volt_min = u_volt - tol; -+ else -+ opp->supplies->u_volt_min = u_volt_min; -+ -+ if ( u_volt_max == u_volt ) -+ opp->supplies->u_volt_max = u_volt + tol; -+ else -+ opp->supplies->u_volt_max = u_volt_max; - - dev_pm_opp_get(opp); - mutex_unlock(&opp_table->lock); diff --git a/target/linux/ipq806x/patches-4.19/0053-regulator-add-smb208-support.patch b/target/linux/ipq806x/patches-4.19/0053-regulator-add-smb208-support.patch deleted file mode 100644 index 0d2862c609..0000000000 --- a/target/linux/ipq806x/patches-4.19/0053-regulator-add-smb208-support.patch +++ /dev/null @@ -1,55 +0,0 @@ -From ef10381ca4d01848ebedb4afb2c78feb8052f103 Mon Sep 17 00:00:00 2001 -From: Adrian Panella -Date: Thu, 9 Mar 2017 08:26:54 +0100 -Subject: [PATCH 53/69] regulator: add smb208 support - -Signed-off-by: Adrian Panella ---- - Documentation/devicetree/bindings/mfd/qcom-rpm.txt | 4 ++++ - drivers/regulator/qcom_rpm-regulator.c | 9 +++++++++ - 2 files changed, 13 insertions(+) - ---- a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt -+++ b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt -@@ -61,6 +61,7 @@ Regulator nodes are identified by their - "qcom,rpm-pm8901-regulators" - "qcom,rpm-pm8921-regulators" - "qcom,rpm-pm8018-regulators" -+ "qcom,rpm-smb208-regulators" - - - vdd_l0_l1_lvs-supply: - - vdd_l2_l11_l12-supply: -@@ -171,6 +172,9 @@ pm8018: - s1, s2, s3, s4, s5, , l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, - l12, l14, lvs1 - -+smb208: -+ s1a, s1b, s2a, s2b -+ - The content of each sub-node is defined by the standard binding for regulators - - see regulator.txt - with additional custom properties described below: - ---- a/drivers/regulator/qcom_rpm-regulator.c -+++ b/drivers/regulator/qcom_rpm-regulator.c -@@ -933,12 +933,21 @@ static const struct rpm_regulator_data r - { } - }; - -+static const struct rpm_regulator_data rpm_smb208_regulators[] = { -+ { "s1a", QCOM_RPM_SMB208_S1a, &smb208_smps, "vin_s1a" }, -+ { "s1b", QCOM_RPM_SMB208_S1b, &smb208_smps, "vin_s1b" }, -+ { "s2a", QCOM_RPM_SMB208_S2a, &smb208_smps, "vin_s2a" }, -+ { "s2b", QCOM_RPM_SMB208_S2b, &smb208_smps, "vin_s2b" }, -+ { } -+}; -+ - static const struct of_device_id rpm_of_match[] = { - { .compatible = "qcom,rpm-pm8018-regulators", - .data = &rpm_pm8018_regulators }, - { .compatible = "qcom,rpm-pm8058-regulators", .data = &rpm_pm8058_regulators }, - { .compatible = "qcom,rpm-pm8901-regulators", .data = &rpm_pm8901_regulators }, - { .compatible = "qcom,rpm-pm8921-regulators", .data = &rpm_pm8921_regulators }, -+ { .compatible = "qcom,rpm-smb208-regulators", .data = &rpm_smb208_regulators }, - { } - }; - MODULE_DEVICE_TABLE(of, rpm_of_match); diff --git a/target/linux/ipq806x/patches-4.19/0054-cpufreq-dt-Handle-OPP-voltage-adjust-events.patch b/target/linux/ipq806x/patches-4.19/0054-cpufreq-dt-Handle-OPP-voltage-adjust-events.patch deleted file mode 100644 index 9620891194..0000000000 --- a/target/linux/ipq806x/patches-4.19/0054-cpufreq-dt-Handle-OPP-voltage-adjust-events.patch +++ /dev/null @@ -1,118 +0,0 @@ -From 10577f74c35bd395951d1b2382c8d821089b5745 Mon Sep 17 00:00:00 2001 -From: Stephen Boyd -Date: Fri, 18 Sep 2015 17:52:08 -0700 -Subject: [PATCH 54/69] cpufreq-dt: Handle OPP voltage adjust events - -On some SoCs the Adaptive Voltage Scaling (AVS) technique is -employed to optimize the operating voltage of a device. At a -given frequency, the hardware monitors dynamic factors and either -makes a suggestion for how much to adjust a voltage for the -current frequency, or it automatically adjusts the voltage -without software intervention. - -In the former case, an AVS driver will call -dev_pm_opp_modify_voltage() and update the voltage for the -particular OPP the CPUs are using. Add an OPP notifier to -cpufreq-dt so that we can adjust the voltage of the CPU when AVS -updates the OPP. - -Signed-off-by: Stephen Boyd -Acked-by: Viresh Kumar -Signed-off-by: Georgi Djakov ---- - drivers/cpufreq/cpufreq-dt.c | 68 ++++++++++++++++++++++++++++++++++++++++++-- - 1 file changed, 65 insertions(+), 3 deletions(-) - ---- a/drivers/cpufreq/cpufreq-dt.c -+++ b/drivers/cpufreq/cpufreq-dt.c -@@ -32,6 +32,9 @@ struct private_data { - struct device *cpu_dev; - struct thermal_cooling_device *cdev; - const char *reg_name; -+ struct notifier_block opp_nb; -+ struct mutex lock; -+ unsigned long opp_freq; - bool have_static_opps; - }; - -@@ -47,12 +50,15 @@ static int set_target(struct cpufreq_pol - unsigned long freq = policy->freq_table[index].frequency; - int ret; - -+ mutex_lock(&priv->lock); - ret = dev_pm_opp_set_rate(priv->cpu_dev, freq * 1000); - - if (!ret) { -+ priv->opp_freq = freq * 1000; - arch_set_freq_scale(policy->related_cpus, freq, - policy->cpuinfo.max_freq); - } -+ mutex_unlock(&priv->lock); - - return ret; - } -@@ -95,6 +101,39 @@ node_put: - return name; - } - -+static int opp_notifier(struct notifier_block *nb, unsigned long event, -+ void *data) -+{ -+ struct dev_pm_opp *opp = data; -+ struct private_data *priv = container_of(nb, struct private_data, -+ opp_nb); -+ struct device *cpu_dev = priv->cpu_dev; -+ struct regulator *cpu_reg; -+ unsigned long volt, freq; -+ int ret = 0; -+ -+ if (event == OPP_EVENT_ADJUST_VOLTAGE) { -+ cpu_reg = dev_pm_opp_get_regulator(cpu_dev); -+ if (IS_ERR(cpu_reg)) { -+ ret = PTR_ERR(cpu_reg); -+ goto out; -+ } -+ volt = dev_pm_opp_get_voltage(opp); -+ freq = dev_pm_opp_get_freq(opp); -+ -+ mutex_lock(&priv->lock); -+ if (freq == priv->opp_freq) { -+ ret = regulator_set_voltage_triplet(cpu_reg, volt, volt, volt); -+ } -+ mutex_unlock(&priv->lock); -+ if (ret) -+ dev_err(cpu_dev, "failed to scale voltage: %d\n", ret); -+ } -+ -+out: -+ return notifier_from_errno(ret); -+} -+ - static int resources_available(void) - { - struct device *cpu_dev; -@@ -251,10 +290,14 @@ static int cpufreq_init(struct cpufreq_p - __func__, ret); - } - -+ mutex_init(&priv->lock); -+ priv->opp_nb.notifier_call = opp_notifier; -+ dev_pm_opp_register_notifier(cpu_dev, &priv->opp_nb); -+ - ret = dev_pm_opp_init_cpufreq_table(cpu_dev, &freq_table); - if (ret) { - dev_err(cpu_dev, "failed to init cpufreq table: %d\n", ret); -- goto out_free_opp; -+ goto out_unregister_nb; - } - - priv->cpu_dev = cpu_dev; -@@ -284,6 +327,8 @@ static int cpufreq_init(struct cpufreq_p - - out_free_cpufreq_table: - dev_pm_opp_free_cpufreq_table(cpu_dev, &freq_table); -+out_unregister_nb: -+ dev_pm_opp_unregister_notifier(cpu_dev, &priv->opp_nb); - out_free_opp: - if (priv->have_static_opps) - dev_pm_opp_of_cpumask_remove_table(policy->cpus); diff --git a/target/linux/ipq806x/patches-4.19/0055-cpufreq-dt-Add-L2-frequency-scaling-support.patch b/target/linux/ipq806x/patches-4.19/0055-cpufreq-dt-Add-L2-frequency-scaling-support.patch deleted file mode 100644 index 5f54120b3a..0000000000 --- a/target/linux/ipq806x/patches-4.19/0055-cpufreq-dt-Add-L2-frequency-scaling-support.patch +++ /dev/null @@ -1,161 +0,0 @@ ---- a/drivers/cpufreq/cpufreq-dt.c -+++ b/drivers/cpufreq/cpufreq-dt.c -@@ -48,16 +48,71 @@ static int set_target(struct cpufreq_pol - { - struct private_data *priv = policy->driver_data; - unsigned long freq = policy->freq_table[index].frequency; -+ struct clk *l2_clk = policy->l2_clk; -+ struct regulator *l2_regulator = policy->l2_regulator; -+ unsigned long l2_freq, target_l2_freq; -+ unsigned long l2_vol, target_l2_vol; -+ unsigned long target_freq; - int ret; - - mutex_lock(&priv->lock); - ret = dev_pm_opp_set_rate(priv->cpu_dev, freq * 1000); - - if (!ret) { -+ if (policy->l2_rate_set) { -+ static unsigned long krait_l2[CONFIG_NR_CPUS] = { }; -+ int cpu, l2_index, tol = 0; -+ -+ target_freq = freq * 1000; -+ -+ krait_l2[policy->cpu] = target_freq; -+ for_each_present_cpu(cpu) -+ target_freq = max(target_freq, krait_l2[cpu]); -+ -+ for (l2_index = 2; l2_index >= 0; l2_index--) -+ if (target_freq >= policy->l2_cpufreq[l2_index]) -+ break; -+ -+ l2_freq = clk_get_rate(l2_clk); -+ target_l2_freq = policy->l2_rate[l2_index]; -+ -+ if (l2_freq != target_l2_freq) { -+ -+ /* -+ * Set to idle bin if switching from normal to high bin -+ * or vice versa -+ */ -+ if ( (l2_index == 2 && l2_freq == policy->l2_rate[1]) || -+ (l2_index == 1 && l2_freq == policy->l2_rate[2]) ) { -+ ret = clk_set_rate(l2_clk, policy->l2_rate[0]); -+ if (ret) -+ goto exit; -+ } -+ /* scale l2 with the core */ -+ ret = clk_set_rate(l2_clk, target_l2_freq); -+ if (ret) -+ goto exit; -+ -+ if (policy->l2_volt_set) { -+ -+ l2_vol = regulator_get_voltage(l2_regulator); -+ target_l2_vol = policy->l2_volt[l2_index]; -+ -+ if (l2_vol != target_l2_vol) { -+ tol = target_l2_vol * policy->l2_volt_tol / 100; -+ ret = regulator_set_voltage_tol(l2_regulator,target_l2_vol,tol); -+ if (ret) -+ goto exit; -+ } -+ } -+ } -+ } - priv->opp_freq = freq * 1000; - arch_set_freq_scale(policy->related_cpus, freq, - policy->cpuinfo.max_freq); - } -+ -+exit: - mutex_unlock(&priv->lock); - - return ret; -@@ -200,6 +255,9 @@ static int cpufreq_init(struct cpufreq_p - bool fallback = false; - const char *name; - int ret; -+ struct device_node *np, *l2_np; -+ struct clk *l2_clk = NULL; -+ struct regulator *l2_regulator = NULL; - - cpu_dev = get_cpu_device(policy->cpu); - if (!cpu_dev) { -@@ -307,6 +365,57 @@ static int cpufreq_init(struct cpufreq_p - - policy->suspend_freq = dev_pm_opp_get_suspend_opp_freq(cpu_dev) / 1000; - -+ policy->l2_rate_set = false; -+ policy->l2_volt_set = false; -+ -+ l2_clk = clk_get(cpu_dev, "l2"); -+ if (!IS_ERR(l2_clk)) -+ policy->l2_clk = l2_clk; -+ -+ l2_np = of_find_node_by_name(NULL, "qcom,l2"); -+ if (l2_np) { -+ struct device_node *vdd; -+ np = of_node_get(priv->cpu_dev->of_node); -+ -+ if (np) -+ of_property_read_u32(np, "voltage-tolerance", &policy->l2_volt_tol); -+ -+ of_property_read_u32_array(l2_np, "qcom,l2-rates", policy->l2_rate, 3); -+ if (policy->l2_rate[0] && policy->l2_rate[1] && policy->l2_rate[2]) { -+ policy->l2_rate_set = true; -+ of_property_read_u32_array(l2_np, "qcom,l2-cpufreq", policy->l2_cpufreq, 3); -+ of_property_read_u32_array(l2_np, "qcom,l2-volt", policy->l2_volt, 3); -+ } else -+ pr_warn("L2: failed to parse L2 rates\n"); -+ -+ if (!policy->l2_cpufreq[0] && !policy->l2_cpufreq[1] && -+ !policy->l2_cpufreq[2] && policy->l2_rate_set) { -+ int i; -+ -+ pr_warn("L2: failed to parse target cpu freq, using defaults\n"); -+ for (i = 0; i < 3; i++) -+ policy->l2_cpufreq[i] = policy->l2_rate[i]; -+ } -+ -+ if (policy->l2_volt[0] && policy->l2_volt[1] && policy->l2_volt[2] && -+ policy->l2_volt_tol && policy->l2_rate_set) { -+ vdd = of_parse_phandle(l2_np, "qcom,l2-supply", 0); -+ -+ if (vdd) { -+ l2_regulator = devm_regulator_get(cpu_dev, vdd->name); -+ if (!IS_ERR(l2_regulator)) { -+ policy->l2_regulator = l2_regulator; -+ policy->l2_volt_set = true; -+ } else { -+ pr_warn("failed to get l2 supply\n"); -+ l2_regulator = NULL; -+ } -+ -+ of_node_put(vdd); -+ } -+ } -+ } -+ - /* Support turbo/boost mode */ - if (policy_has_boost_freq(policy)) { - /* This gets disabled by core on driver unregister */ ---- a/include/linux/cpufreq.h -+++ b/include/linux/cpufreq.h -@@ -72,7 +72,15 @@ struct cpufreq_policy { - should set cpufreq */ - unsigned int cpu; /* cpu managing this policy, must be online */ - -- struct clk *clk; -+ struct clk *clk; -+ struct clk *l2_clk; /* L2 clock */ -+ struct regulator *l2_regulator; /* L2 supply */ -+ unsigned int l2_rate[3]; /* L2 bus clock rate */ -+ bool l2_rate_set; -+ unsigned int l2_cpufreq[3]; /* L2 target CPU frequency */ -+ unsigned int l2_volt[3]; /* L2 voltage array */ -+ bool l2_volt_set; -+ unsigned int l2_volt_tol; /* L2 voltage tolerance */ - struct cpufreq_cpuinfo cpuinfo;/* see above */ - - unsigned int min; /* in kHz */ diff --git a/target/linux/ipq806x/patches-4.19/0056-cpufreq-dt-Add-missing-rcu-locks.patch b/target/linux/ipq806x/patches-4.19/0056-cpufreq-dt-Add-missing-rcu-locks.patch deleted file mode 100644 index ef03ba4de8..0000000000 --- a/target/linux/ipq806x/patches-4.19/0056-cpufreq-dt-Add-missing-rcu-locks.patch +++ /dev/null @@ -1,23 +0,0 @@ -From 001a8dcb56ced58c518aaa10a4f0ba5e878705b6 Mon Sep 17 00:00:00 2001 -From: Georgi Djakov -Date: Tue, 17 May 2016 16:15:43 +0300 -Subject: [PATCH 56/69] cpufreq-dt: Add missing rcu locks - -Signed-off-by: Georgi Djakov ---- - drivers/cpufreq/cpufreq-dt.c | 2 ++ - 1 file changed, 2 insertions(+) - ---- a/drivers/cpufreq/cpufreq-dt.c -+++ b/drivers/cpufreq/cpufreq-dt.c -@@ -173,8 +173,10 @@ static int opp_notifier(struct notifier_ - ret = PTR_ERR(cpu_reg); - goto out; - } -+ rcu_read_lock(); - volt = dev_pm_opp_get_voltage(opp); - freq = dev_pm_opp_get_freq(opp); -+ rcu_read_unlock(); - - mutex_lock(&priv->lock); - if (freq == priv->opp_freq) { diff --git a/target/linux/ipq806x/patches-4.19/0057-add-fab-scaling-support-with-cpufreq.patch b/target/linux/ipq806x/patches-4.19/0057-add-fab-scaling-support-with-cpufreq.patch deleted file mode 100644 index dc65230f47..0000000000 --- a/target/linux/ipq806x/patches-4.19/0057-add-fab-scaling-support-with-cpufreq.patch +++ /dev/null @@ -1,243 +0,0 @@ ---- a/drivers/clk/qcom/Makefile -+++ b/drivers/clk/qcom/Makefile -@@ -15,6 +15,7 @@ clk-qcom-$(CONFIG_KRAIT_CLOCKS) += clk-k - clk-qcom-y += clk-hfpll.o - clk-qcom-y += reset.o - clk-qcom-$(CONFIG_QCOM_GDSC) += gdsc.o -+clk-qcom-y += fab_scaling.o - - # Keep alphabetically sorted by config - obj-$(CONFIG_APQ_GCC_8084) += gcc-apq8084.o ---- /dev/null -+++ b/drivers/clk/qcom/fab_scaling.c -@@ -0,0 +1,172 @@ -+/* -+ * Copyright (c) 2015, The Linux Foundation. All rights reserved. -+ * -+ * Permission to use, copy, modify, and/or distribute this software for any -+ * purpose with or without fee is hereby granted, provided that the above -+ * copyright notice and this permission notice appear in all copies. -+ * -+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES -+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF -+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR -+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES -+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN -+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF -+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. -+ */ -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+struct qcom_fab_scaling_data { -+ u32 fab_freq_high; -+ u32 fab_freq_nominal; -+ u32 cpu_freq_threshold; -+ struct clk *apps_fab_clk; -+ struct clk *ddr_fab_clk; -+}; -+ -+static struct qcom_fab_scaling_data *drv_data; -+ -+int scale_fabrics(unsigned long max_cpu_freq) -+{ -+ struct clk *apps_fab_clk = drv_data->apps_fab_clk, -+ *ddr_fab_clk = drv_data->ddr_fab_clk; -+ unsigned long target_freq, cur_freq; -+ int ret; -+ -+ /* Skip fab scaling if the driver is not ready */ -+ if (!apps_fab_clk || !ddr_fab_clk) -+ return 0; -+ -+ if (max_cpu_freq > drv_data->cpu_freq_threshold) -+ target_freq = drv_data->fab_freq_high; -+ else -+ target_freq = drv_data->fab_freq_nominal; -+ -+ cur_freq = clk_get_rate(ddr_fab_clk); -+ -+ if (target_freq != cur_freq) { -+ ret = clk_set_rate(apps_fab_clk, target_freq); -+ if (ret) -+ return ret; -+ ret = clk_set_rate(ddr_fab_clk, target_freq); -+ if (ret) -+ return ret; -+ } -+ -+ return 0; -+} -+EXPORT_SYMBOL(scale_fabrics); -+ -+static int ipq806x_fab_scaling_probe(struct platform_device *pdev) -+{ -+ struct device_node *np = pdev->dev.of_node; -+ struct clk *apps_fab_clk, *ddr_fab_clk; -+ int ret; -+ -+ if (!np) -+ return -ENODEV; -+ -+ drv_data = kzalloc(sizeof(*drv_data), GFP_KERNEL); -+ if (!drv_data) -+ return -ENOMEM; -+ -+ if (of_property_read_u32(np, "fab_freq_high", &drv_data->fab_freq_high)) { -+ pr_err("FABRICS turbo freq not found. Using defaults...\n"); -+ drv_data->fab_freq_high = 533000000; -+ } -+ -+ if (of_property_read_u32(np, "fab_freq_nominal", &drv_data->fab_freq_nominal)) { -+ pr_err("FABRICS nominal freq not found. Using defaults...\n"); -+ drv_data->fab_freq_nominal = 400000000; -+ } -+ -+ if (of_property_read_u32(np, "cpu_freq_threshold", &drv_data->cpu_freq_threshold)) { -+ pr_err("FABRICS cpu freq threshold not found. Using defaults...\n"); -+ drv_data->cpu_freq_threshold = 1000000000; -+ } -+ -+ drv_data->apps_fab_clk = devm_clk_get(&pdev->dev, "apps-fab-clk"); -+ apps_fab_clk = drv_data->apps_fab_clk; -+ ret = PTR_ERR_OR_ZERO(apps_fab_clk); -+ if (ret) { -+ /* -+ * If apps fab clk node is present, but clock is not yet -+ * registered, we should try defering probe. -+ */ -+ if (ret != -EPROBE_DEFER) { -+ pr_err("Failed to get APPS FABRIC clock: %d\n", ret); -+ ret = -ENODEV; -+ } -+ goto err; -+ } -+ -+ clk_set_rate(apps_fab_clk, drv_data->fab_freq_high); -+ clk_prepare_enable(apps_fab_clk); -+ -+ drv_data->ddr_fab_clk = devm_clk_get(&pdev->dev, "ddr-fab-clk"); -+ ddr_fab_clk = drv_data->ddr_fab_clk; -+ ret = PTR_ERR_OR_ZERO(ddr_fab_clk); -+ if (ret) { -+ /* -+ * If ddr fab clk node is present, but clock is not yet -+ * registered, we should try defering probe. -+ */ -+ if (ret != -EPROBE_DEFER) { -+ pr_err("Failed to get DDR FABRIC clock: %d\n", ret); -+ ddr_fab_clk = NULL; -+ ret = -ENODEV; -+ } -+ goto err; -+ } -+ -+ clk_set_rate(ddr_fab_clk, drv_data->fab_freq_high); -+ clk_prepare_enable(ddr_fab_clk); -+ -+ return 0; -+err: -+ kfree(drv_data); -+ return ret; -+} -+ -+static int ipq806x_fab_scaling_remove(struct platform_device *pdev) -+{ -+ kfree(drv_data); -+ return 0; -+} -+ -+static const struct of_device_id fab_scaling_ipq806x_match_table[] = { -+ { .compatible = "qcom,fab-scaling" }, -+ { } -+}; -+ -+static struct platform_driver fab_scaling_ipq806x_driver = { -+ .probe = ipq806x_fab_scaling_probe, -+ .remove = ipq806x_fab_scaling_remove, -+ .driver = { -+ .name = "fab-scaling", -+ .of_match_table = fab_scaling_ipq806x_match_table, -+ }, -+}; -+ -+static int __init fab_scaling_ipq806x_init(void) -+{ -+ return platform_driver_register(&fab_scaling_ipq806x_driver); -+} -+late_initcall(fab_scaling_ipq806x_init); -+ -+static void __exit fab_scaling_ipq806x_exit(void) -+{ -+ platform_driver_unregister(&fab_scaling_ipq806x_driver); -+} -+module_exit(fab_scaling_ipq806x_exit); ---- /dev/null -+++ b/include/linux/fab_scaling.h -@@ -0,0 +1,31 @@ -+/* -+ * Copyright (c) 2015, The Linux Foundation. All rights reserved. -+ * -+ * Permission to use, copy, modify, and/or distribute this software for any -+ * purpose with or without fee is hereby granted, provided that the above -+ * copyright notice and this permission notice appear in all copies. -+ * -+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES -+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF -+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR -+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES -+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN -+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF -+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. -+ */ -+ -+ -+#ifndef __FAB_SCALING_H -+#define __FAB_SCALING_H -+ -+/** -+ * scale_fabrics - Scale DDR and APPS FABRICS -+ * -+ * This function monitors all the registered clocks and does APPS -+ * and DDR FABRIC scaling based on the idle frequencies with which -+ * it was registered. -+ * -+ */ -+int scale_fabrics(unsigned long max_cpu_freq); -+ -+#endif ---- a/drivers/cpufreq/cpufreq-dt.c -+++ b/drivers/cpufreq/cpufreq-dt.c -@@ -24,6 +24,7 @@ - #include - #include - #include -+#include - - #include "cpufreq-dt.h" - -@@ -106,6 +107,13 @@ static int set_target(struct cpufreq_pol - } - } - } -+ -+ /* -+ * Scale fabrics with max freq across all cores -+ */ -+ ret = scale_fabrics(target_freq); -+ if (ret) -+ goto exit; - } - priv->opp_freq = freq * 1000; - arch_set_freq_scale(policy->related_cpus, freq, diff --git a/target/linux/ipq806x/patches-4.19/0059-ARM-cpuidle-Add-cpuidle-support-for-QCOM-cpus.patch b/target/linux/ipq806x/patches-4.19/0059-ARM-cpuidle-Add-cpuidle-support-for-QCOM-cpus.patch deleted file mode 100644 index 5bd58c8137..0000000000 --- a/target/linux/ipq806x/patches-4.19/0059-ARM-cpuidle-Add-cpuidle-support-for-QCOM-cpus.patch +++ /dev/null @@ -1,29 +0,0 @@ -From 04ca10340f1b4d92e849724d322a7ca225d11539 Mon Sep 17 00:00:00 2001 -From: Lina Iyer -Date: Wed, 25 Mar 2015 14:25:29 -0600 -Subject: [PATCH 59/69] ARM: cpuidle: Add cpuidle support for QCOM cpus - -Define ARM_QCOM_CPUIDLE config item to enable cpuidle support. - -Cc: Stephen Boyd -Cc: Arnd Bergmann -Cc: Kevin Hilman -Cc: Daniel Lezcano -Signed-off-by: Lina Iyer ---- - drivers/cpuidle/Kconfig.arm | 7 +++++++ - 1 file changed, 7 insertions(+) - ---- a/drivers/cpuidle/Kconfig.arm -+++ b/drivers/cpuidle/Kconfig.arm -@@ -75,3 +75,10 @@ config ARM_MVEBU_V7_CPUIDLE - depends on ARCH_MVEBU && !ARM64 - help - Select this to enable cpuidle on Armada 370, 38x and XP processors. -+ -+config ARM_QCOM_CPUIDLE -+ bool "CPU Idle Driver for QCOM processors" -+ depends on ARCH_QCOM -+ select ARM_CPUIDLE -+ help -+ Select this to enable cpuidle on QCOM processors. diff --git a/target/linux/ipq806x/patches-4.19/0060-HACK-arch-arm-force-ZRELADDR-on-arch-qcom.patch b/target/linux/ipq806x/patches-4.19/0060-HACK-arch-arm-force-ZRELADDR-on-arch-qcom.patch deleted file mode 100644 index 543f18ce4d..0000000000 --- a/target/linux/ipq806x/patches-4.19/0060-HACK-arch-arm-force-ZRELADDR-on-arch-qcom.patch +++ /dev/null @@ -1,62 +0,0 @@ -From fa71139b55e114aa8c3c4823ff8ee7d49ee810d4 Mon Sep 17 00:00:00 2001 -From: Mathieu Olivari -Date: Wed, 29 Apr 2015 15:21:46 -0700 -Subject: [PATCH 60/69] HACK: arch: arm: force ZRELADDR on arch-qcom - -ARCH_QCOM is using the ARCH_MULTIPLATFORM option, as now recommended -on most ARM architectures. This automatically calculate ZRELADDR by -masking PHYS_OFFSET with 0xf8000000. - -However, on IPQ806x, the first ~20MB of RAM is reserved for the hardware -network accelerators, and the bootloader removes this section from the -layout passed from the ATAGS (when used). - -For newer bootloader, when DT is used, this is not a problem, we just -reserve this memory in the device tree. But if the bootloader doesn't -have DT support, then ATAGS have to be used. In this case, the ARM -decompressor will position the kernel in this low mem, which will not be -in the RAM section mapped by the bootloader, which means the kernel will -freeze in the middle of the boot process trying to map the memory. - -As a work around, this patch allows disabling AUTO_ZRELADDR when -ARCH_QCOM is selected. It makes the zImage usage possible on bootloaders -which don't support device-tree, which is the case on certain early -IPQ806x based designs. - -Signed-off-by: Mathieu Olivari ---- - arch/arm/Kconfig | 2 +- - arch/arm/Makefile | 2 ++ - arch/arm/mach-qcom/Makefile.boot | 1 + - 3 files changed, 4 insertions(+), 1 deletion(-) - create mode 100644 arch/arm/mach-qcom/Makefile.boot - ---- a/arch/arm/Kconfig -+++ b/arch/arm/Kconfig -@@ -331,7 +331,7 @@ config ARCH_MULTIPLATFORM - depends on MMU - select ARM_HAS_SG_CHAIN - select ARM_PATCH_PHYS_VIRT -- select AUTO_ZRELADDR -+ select AUTO_ZRELADDR if !ARCH_QCOM - select TIMER_OF - select COMMON_CLK - select GENERIC_CLOCKEVENTS ---- a/arch/arm/Makefile -+++ b/arch/arm/Makefile -@@ -255,9 +255,11 @@ MACHINE := arch/arm/mach-$(word 1,$(mac - else - MACHINE := - endif -+ifeq ($(CONFIG_ARCH_QCOM),) - ifeq ($(CONFIG_ARCH_MULTIPLATFORM),y) - MACHINE := - endif -+endif - - machdirs := $(patsubst %,arch/arm/mach-%/,$(machine-y)) - platdirs := $(patsubst %,arch/arm/plat-%/,$(sort $(plat-y))) ---- /dev/null -+++ b/arch/arm/mach-qcom/Makefile.boot -@@ -0,0 +1 @@ -+zreladdr-y+= 0x42208000 diff --git a/target/linux/ipq806x/patches-4.19/0061-mtd-rootfs-conflicts-with-OpenWrt-auto-mounting.patch b/target/linux/ipq806x/patches-4.19/0061-mtd-rootfs-conflicts-with-OpenWrt-auto-mounting.patch deleted file mode 100644 index a4a957545b..0000000000 --- a/target/linux/ipq806x/patches-4.19/0061-mtd-rootfs-conflicts-with-OpenWrt-auto-mounting.patch +++ /dev/null @@ -1,23 +0,0 @@ -From 5001f2e1a325b68dbf225bd17f69a4d3d975cca5 Mon Sep 17 00:00:00 2001 -From: John Crispin -Date: Thu, 9 Mar 2017 09:31:44 +0100 -Subject: [PATCH 61/69] mtd: "rootfs" conflicts with OpenWrt auto mounting - -Signed-off-by: John Crispin ---- - drivers/mtd/qcom_smem_part.c | 4 ++++ - 1 file changed, 4 insertions(+) - ---- a/drivers/mtd/qcom_smem_part.c -+++ b/drivers/mtd/qcom_smem_part.c -@@ -189,6 +189,10 @@ static int parse_qcom_smem_partitions(st - m_part->size = le32_to_cpu(s_part->size) * (*smem_blksz); - m_part->offset = le32_to_cpu(s_part->start) * (*smem_blksz); - -+ /* "rootfs" conflicts with OpenWrt auto mounting */ -+ if (mtd_type_is_nand(master) && !strcmp(m_part->name, "rootfs")) -+ m_part->name = "ubi"; -+ - /* - * The last SMEM partition may have its size marked as - * something like 0xffffffff, which means "until the end of the diff --git a/target/linux/ipq806x/patches-4.19/0062-ipq806x-gcc-Added-the-enable-regs-and-mask-for-PRNG.patch b/target/linux/ipq806x/patches-4.19/0062-ipq806x-gcc-Added-the-enable-regs-and-mask-for-PRNG.patch deleted file mode 100644 index 717934315a..0000000000 --- a/target/linux/ipq806x/patches-4.19/0062-ipq806x-gcc-Added-the-enable-regs-and-mask-for-PRNG.patch +++ /dev/null @@ -1,25 +0,0 @@ -From a16fcf911a020e46439a3bb3e702463fc3159831 Mon Sep 17 00:00:00 2001 -From: Abhishek Sahu -Date: Wed, 18 Nov 2015 12:38:56 +0530 -Subject: [PATCH 62/69] ipq806x: gcc: Added the enable regs and mask for PRNG - -kernel got hanged while reading from /dev/hwrng at the -time of PRNG clock enable - -Change-Id: I89856c7e19e6639508e6a2774304583a3ec91172 -Signed-off-by: Abhishek Sahu ---- - drivers/clk/qcom/gcc-ipq806x.c | 2 ++ - 1 file changed, 2 insertions(+) - ---- a/drivers/clk/qcom/gcc-ipq806x.c -+++ b/drivers/clk/qcom/gcc-ipq806x.c -@@ -1233,6 +1233,8 @@ static struct clk_rcg prng_src = { - .parent_map = gcc_pxo_pll8_map, - }, - .clkr = { -+ .enable_reg = 0x2e80, -+ .enable_mask = BIT(11), - .hw.init = &(struct clk_init_data){ - .name = "prng_src", - .parent_names = gcc_pxo_pll8, diff --git a/target/linux/ipq806x/patches-4.19/0063-1-ipq806x-tsens-driver.patch b/target/linux/ipq806x/patches-4.19/0063-1-ipq806x-tsens-driver.patch deleted file mode 100644 index 9ee88533aa..0000000000 --- a/target/linux/ipq806x/patches-4.19/0063-1-ipq806x-tsens-driver.patch +++ /dev/null @@ -1,614 +0,0 @@ -From 3302e1e1a3cfa4e67fda2a61d6f0c42205d40932 Mon Sep 17 00:00:00 2001 -From: Rajith Cherian -Date: Tue, 14 Feb 2017 18:30:43 +0530 -Subject: [PATCH] ipq8064: tsens: Base tsens driver for IPQ8064 - -Add TSENS driver template to support IPQ8064. -This is a base file copied from tsens-8960.c - -Change-Id: I47c573fdfa2d898243c6a6ba952d1632f91391f7 -Signed-off-by: Rajith Cherian - -ipq8064: tsens: TSENS driver support for IPQ8064 - -Support for IPQ8064 tsens driver. The driver works -with the thermal framework. The driver overrides the -following fucntionalities: - -1. Get current temperature. -2. Get/Set trip temperatures. -3. Enabled/Disable trip points. -4. ISR for threshold generated interrupt. -5. Notify userspace when trip points are hit. - -Change-Id: I8bc7204fd627d10875ab13fc1de8cb6c2ed7a918 -Signed-off-by: Rajith Cherian ---- - ---- a/drivers/thermal/qcom/Makefile -+++ b/drivers/thermal/qcom/Makefile -@@ -1,2 +1,3 @@ - obj-$(CONFIG_QCOM_TSENS) += qcom_tsens.o --qcom_tsens-y += tsens.o tsens-common.o tsens-8916.o tsens-8974.o tsens-8960.o tsens-v2.o -+qcom_tsens-y += tsens.o tsens-common.o tsens-8916.o tsens-8974.o tsens-8960.o tsens-v2.o \ -+ tsens-ipq8064.o ---- /dev/null -+++ b/drivers/thermal/qcom/tsens-ipq8064.c -@@ -0,0 +1,551 @@ -+/* -+ * Copyright (c) 2015, The Linux Foundation. All rights reserved. -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 and -+ * only version 2 as published by the Free Software Foundation. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ */ -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include "tsens.h" -+ -+#define CAL_MDEGC 30000 -+ -+#define CONFIG_ADDR 0x3640 -+/* CONFIG_ADDR bitmasks */ -+#define CONFIG 0x9b -+#define CONFIG_MASK 0xf -+#define CONFIG_SHIFT 0 -+ -+#define STATUS_CNTL_8064 0x3660 -+#define CNTL_ADDR 0x3620 -+/* CNTL_ADDR bitmasks */ -+#define EN BIT(0) -+#define SW_RST BIT(1) -+#define SENSOR0_EN BIT(3) -+#define SLP_CLK_ENA BIT(26) -+#define MEASURE_PERIOD 1 -+#define SENSOR0_SHIFT 3 -+ -+/* INT_STATUS_ADDR bitmasks */ -+#define MIN_STATUS_MASK BIT(0) -+#define LOWER_STATUS_CLR BIT(1) -+#define UPPER_STATUS_CLR BIT(2) -+#define MAX_STATUS_MASK BIT(3) -+ -+#define THRESHOLD_ADDR 0x3624 -+/* THRESHOLD_ADDR bitmasks */ -+#define THRESHOLD_MAX_CODE 0x20000 -+#define THRESHOLD_MIN_CODE 0 -+#define THRESHOLD_MAX_LIMIT_SHIFT 24 -+#define THRESHOLD_MIN_LIMIT_SHIFT 16 -+#define THRESHOLD_UPPER_LIMIT_SHIFT 8 -+#define THRESHOLD_LOWER_LIMIT_SHIFT 0 -+#define THRESHOLD_MAX_LIMIT_MASK (THRESHOLD_MAX_CODE << \ -+ THRESHOLD_MAX_LIMIT_SHIFT) -+#define THRESHOLD_MIN_LIMIT_MASK (THRESHOLD_MAX_CODE << \ -+ THRESHOLD_MIN_LIMIT_SHIFT) -+#define THRESHOLD_UPPER_LIMIT_MASK (THRESHOLD_MAX_CODE << \ -+ THRESHOLD_UPPER_LIMIT_SHIFT) -+#define THRESHOLD_LOWER_LIMIT_MASK (THRESHOLD_MAX_CODE << \ -+ THRESHOLD_LOWER_LIMIT_SHIFT) -+ -+/* Initial temperature threshold values */ -+#define LOWER_LIMIT_TH 0x9d /* 95C */ -+#define UPPER_LIMIT_TH 0xa6 /* 105C */ -+#define MIN_LIMIT_TH 0x0 -+#define MAX_LIMIT_TH 0xff -+ -+#define S0_STATUS_ADDR 0x3628 -+#define STATUS_ADDR_OFFSET 2 -+#define SENSOR_STATUS_SIZE 4 -+#define INT_STATUS_ADDR 0x363c -+#define TRDY_MASK BIT(7) -+#define TIMEOUT_US 100 -+ -+#define TSENS_EN BIT(0) -+#define TSENS_SW_RST BIT(1) -+#define TSENS_ADC_CLK_SEL BIT(2) -+#define SENSOR0_EN BIT(3) -+#define SENSOR1_EN BIT(4) -+#define SENSOR2_EN BIT(5) -+#define SENSOR3_EN BIT(6) -+#define SENSOR4_EN BIT(7) -+#define SENSORS_EN (SENSOR0_EN | SENSOR1_EN | \ -+ SENSOR2_EN | SENSOR3_EN | SENSOR4_EN) -+#define TSENS_8064_SENSOR5_EN BIT(8) -+#define TSENS_8064_SENSOR6_EN BIT(9) -+#define TSENS_8064_SENSOR7_EN BIT(10) -+#define TSENS_8064_SENSOR8_EN BIT(11) -+#define TSENS_8064_SENSOR9_EN BIT(12) -+#define TSENS_8064_SENSOR10_EN BIT(13) -+#define TSENS_8064_SENSORS_EN (SENSORS_EN | \ -+ TSENS_8064_SENSOR5_EN | \ -+ TSENS_8064_SENSOR6_EN | \ -+ TSENS_8064_SENSOR7_EN | \ -+ TSENS_8064_SENSOR8_EN | \ -+ TSENS_8064_SENSOR9_EN | \ -+ TSENS_8064_SENSOR10_EN) -+ -+#define TSENS_8064_SEQ_SENSORS 5 -+#define TSENS_8064_S4_S5_OFFSET 40 -+#define TSENS_FACTOR 1 -+ -+/* Trips: from very hot to very cold */ -+enum tsens_trip_type { -+ TSENS_TRIP_STAGE3 = 0, -+ TSENS_TRIP_STAGE2, -+ TSENS_TRIP_STAGE1, -+ TSENS_TRIP_STAGE0, -+ TSENS_TRIP_NUM, -+}; -+ -+u32 tsens_8064_slope[] = { -+ 1176, 1176, 1154, 1176, -+ 1111, 1132, 1132, 1199, -+ 1132, 1199, 1132 -+ }; -+ -+/* Temperature on y axis and ADC-code on x-axis */ -+static inline int code_to_degC(u32 adc_code, const struct tsens_sensor *s) -+{ -+ int degcbeforefactor, degc; -+ -+ degcbeforefactor = (adc_code * s->slope) + s->offset; -+ -+ if (degcbeforefactor == 0) -+ degc = degcbeforefactor; -+ else if (degcbeforefactor > 0) -+ degc = (degcbeforefactor + TSENS_FACTOR/2) -+ / TSENS_FACTOR; -+ else -+ degc = (degcbeforefactor - TSENS_FACTOR/2) -+ / TSENS_FACTOR; -+ -+ return degc; -+} -+ -+static int degC_to_code(int degC, const struct tsens_sensor *s) -+{ -+ int code = ((degC * TSENS_FACTOR - s->offset) + (s->slope/2)) -+ / s->slope; -+ -+ if (code > THRESHOLD_MAX_CODE) -+ code = THRESHOLD_MAX_CODE; -+ else if (code < THRESHOLD_MIN_CODE) -+ code = THRESHOLD_MIN_CODE; -+ return code; -+} -+ -+static int suspend_ipq8064(struct tsens_device *tmdev) -+{ -+ int ret; -+ unsigned int mask; -+ struct regmap *map = tmdev->map; -+ -+ ret = regmap_read(map, THRESHOLD_ADDR, &tmdev->ctx.threshold); -+ if (ret) -+ return ret; -+ -+ ret = regmap_read(map, CNTL_ADDR, &tmdev->ctx.control); -+ if (ret) -+ return ret; -+ -+ mask = SLP_CLK_ENA | EN; -+ -+ ret = regmap_update_bits(map, CNTL_ADDR, mask, 0); -+ if (ret) -+ return ret; -+ -+ return 0; -+} -+ -+static int resume_ipq8064(struct tsens_device *tmdev) -+{ -+ int ret; -+ struct regmap *map = tmdev->map; -+ -+ ret = regmap_update_bits(map, CNTL_ADDR, SW_RST, SW_RST); -+ if (ret) -+ return ret; -+ -+ ret = regmap_update_bits(map, CONFIG_ADDR, CONFIG_MASK, CONFIG); -+ if (ret) -+ return ret; -+ -+ ret = regmap_write(map, THRESHOLD_ADDR, tmdev->ctx.threshold); -+ if (ret) -+ return ret; -+ -+ ret = regmap_write(map, CNTL_ADDR, tmdev->ctx.control); -+ if (ret) -+ return ret; -+ -+ return 0; -+} -+ -+static void notify_uspace_tsens_fn(struct work_struct *work) -+{ -+ struct tsens_sensor *s = container_of(work, struct tsens_sensor, -+ notify_work); -+ -+ sysfs_notify(&s->tzd->device.kobj, NULL, "type"); -+} -+ -+static void tsens_scheduler_fn(struct work_struct *work) -+{ -+ struct tsens_device *tmdev = container_of(work, struct tsens_device, -+ tsens_work); -+ unsigned int threshold, threshold_low, code, reg, sensor, mask; -+ unsigned int sensor_addr; -+ bool upper_th_x, lower_th_x; -+ int adc_code, ret; -+ -+ ret = regmap_read(tmdev->map, STATUS_CNTL_8064, ®); -+ if (ret) -+ return; -+ reg = reg | LOWER_STATUS_CLR | UPPER_STATUS_CLR; -+ ret = regmap_write(tmdev->map, STATUS_CNTL_8064, reg); -+ if (ret) -+ return; -+ -+ mask = ~(LOWER_STATUS_CLR | UPPER_STATUS_CLR); -+ ret = regmap_read(tmdev->map, THRESHOLD_ADDR, &threshold); -+ if (ret) -+ return; -+ threshold_low = (threshold & THRESHOLD_LOWER_LIMIT_MASK) -+ >> THRESHOLD_LOWER_LIMIT_SHIFT; -+ threshold = (threshold & THRESHOLD_UPPER_LIMIT_MASK) -+ >> THRESHOLD_UPPER_LIMIT_SHIFT; -+ -+ ret = regmap_read(tmdev->map, STATUS_CNTL_8064, ®); -+ if (ret) -+ return; -+ -+ ret = regmap_read(tmdev->map, CNTL_ADDR, &sensor); -+ if (ret) -+ return; -+ sensor &= (uint32_t) TSENS_8064_SENSORS_EN; -+ sensor >>= SENSOR0_SHIFT; -+ -+ /* Constraint: There is only 1 interrupt control register for all -+ * 11 temperature sensor. So monitoring more than 1 sensor based -+ * on interrupts will yield inconsistent result. To overcome this -+ * issue we will monitor only sensor 0 which is the master sensor. -+ */ -+ -+ /* Skip if the sensor is disabled */ -+ if (sensor & 1) { -+ ret = regmap_read(tmdev->map, tmdev->sensor[0].status, &code); -+ if (ret) -+ return; -+ upper_th_x = code >= threshold; -+ lower_th_x = code <= threshold_low; -+ if (upper_th_x) -+ mask |= UPPER_STATUS_CLR; -+ if (lower_th_x) -+ mask |= LOWER_STATUS_CLR; -+ if (upper_th_x || lower_th_x) { -+ /* Notify user space */ -+ schedule_work(&tmdev->sensor[0].notify_work); -+ regmap_read(tmdev->map, sensor_addr, &adc_code); -+ pr_debug("Trigger (%d degrees) for sensor %d\n", -+ code_to_degC(adc_code, &tmdev->sensor[0]), 0); -+ } -+ } -+ regmap_write(tmdev->map, STATUS_CNTL_8064, reg & mask); -+ -+ /* force memory to sync */ -+ mb(); -+} -+ -+static irqreturn_t tsens_isr(int irq, void *data) -+{ -+ struct tsens_device *tmdev = data; -+ -+ schedule_work(&tmdev->tsens_work); -+ return IRQ_HANDLED; -+} -+ -+static void hw_init(struct tsens_device *tmdev) -+{ -+ int ret; -+ unsigned int reg_cntl = 0, reg_cfg = 0, reg_thr = 0; -+ unsigned int reg_status_cntl = 0; -+ -+ regmap_read(tmdev->map, CNTL_ADDR, ®_cntl); -+ regmap_write(tmdev->map, CNTL_ADDR, reg_cntl | TSENS_SW_RST); -+ -+ reg_cntl |= SLP_CLK_ENA | (MEASURE_PERIOD << 18) -+ | (((1 << tmdev->num_sensors) - 1) << SENSOR0_SHIFT); -+ regmap_write(tmdev->map, CNTL_ADDR, reg_cntl); -+ regmap_read(tmdev->map, STATUS_CNTL_8064, ®_status_cntl); -+ reg_status_cntl |= LOWER_STATUS_CLR | UPPER_STATUS_CLR -+ | MIN_STATUS_MASK | MAX_STATUS_MASK; -+ regmap_write(tmdev->map, STATUS_CNTL_8064, reg_status_cntl); -+ reg_cntl |= TSENS_EN; -+ regmap_write(tmdev->map, CNTL_ADDR, reg_cntl); -+ -+ regmap_read(tmdev->map, CONFIG_ADDR, ®_cfg); -+ reg_cfg = (reg_cfg & ~CONFIG_MASK) | (CONFIG << CONFIG_SHIFT); -+ regmap_write(tmdev->map, CONFIG_ADDR, reg_cfg); -+ -+ reg_thr |= (LOWER_LIMIT_TH << THRESHOLD_LOWER_LIMIT_SHIFT) -+ | (UPPER_LIMIT_TH << THRESHOLD_UPPER_LIMIT_SHIFT) -+ | (MIN_LIMIT_TH << THRESHOLD_MIN_LIMIT_SHIFT) -+ | (MAX_LIMIT_TH << THRESHOLD_MAX_LIMIT_SHIFT); -+ -+ regmap_write(tmdev->map, THRESHOLD_ADDR, reg_thr); -+ -+ ret = devm_request_irq(tmdev->dev, tmdev->tsens_irq, tsens_isr, -+ IRQF_TRIGGER_RISING, "tsens_interrupt", tmdev); -+ if (ret < 0) { -+ pr_err("%s: request_irq FAIL: %d\n", __func__, ret); -+ return; -+ } -+ -+ INIT_WORK(&tmdev->tsens_work, tsens_scheduler_fn); -+} -+ -+static int init_ipq8064(struct tsens_device *tmdev) -+{ -+ int ret, i; -+ u32 reg_cntl, offset = 0; -+ -+ init_common(tmdev); -+ if (!tmdev->map) -+ return -ENODEV; -+ -+ /* -+ * The status registers for each sensor are discontiguous -+ * because some SoCs have 5 sensors while others have more -+ * but the control registers stay in the same place, i.e -+ * directly after the first 5 status registers. -+ */ -+ for (i = 0; i < tmdev->num_sensors; i++) { -+ if (i >= TSENS_8064_SEQ_SENSORS) -+ offset = TSENS_8064_S4_S5_OFFSET; -+ -+ tmdev->sensor[i].status = S0_STATUS_ADDR + offset -+ + (i << STATUS_ADDR_OFFSET); -+ tmdev->sensor[i].slope = tsens_8064_slope[i]; -+ INIT_WORK(&tmdev->sensor[i].notify_work, -+ notify_uspace_tsens_fn); -+ } -+ -+ reg_cntl = SW_RST; -+ ret = regmap_update_bits(tmdev->map, CNTL_ADDR, SW_RST, reg_cntl); -+ if (ret) -+ return ret; -+ -+ reg_cntl |= SLP_CLK_ENA | (MEASURE_PERIOD << 18); -+ reg_cntl &= ~SW_RST; -+ ret = regmap_update_bits(tmdev->map, CONFIG_ADDR, -+ CONFIG_MASK, CONFIG); -+ -+ reg_cntl |= GENMASK(tmdev->num_sensors - 1, 0) << SENSOR0_SHIFT; -+ ret = regmap_write(tmdev->map, CNTL_ADDR, reg_cntl); -+ if (ret) -+ return ret; -+ -+ reg_cntl |= EN; -+ ret = regmap_write(tmdev->map, CNTL_ADDR, reg_cntl); -+ if (ret) -+ return ret; -+ -+ return 0; -+} -+ -+static int calibrate_ipq8064(struct tsens_device *tmdev) -+{ -+ int i; -+ char *data, *data_backup; -+ -+ ssize_t num_read = tmdev->num_sensors; -+ struct tsens_sensor *s = tmdev->sensor; -+ -+ data = qfprom_read(tmdev->dev, "calib"); -+ if (IS_ERR(data)) { -+ pr_err("Calibration not found.\n"); -+ return PTR_ERR(data); -+ } -+ -+ data_backup = qfprom_read(tmdev->dev, "calib_backup"); -+ if (IS_ERR(data_backup)) { -+ pr_err("Backup calibration not found.\n"); -+ return PTR_ERR(data_backup); -+ } -+ -+ for (i = 0; i < num_read; i++) { -+ s[i].calib_data = readb_relaxed(data + i); -+ s[i].calib_data_backup = readb_relaxed(data_backup + i); -+ -+ if (s[i].calib_data_backup) -+ s[i].calib_data = s[i].calib_data_backup; -+ if (!s[i].calib_data) { -+ pr_err("QFPROM TSENS calibration data not present\n"); -+ return -ENODEV; -+ } -+ s[i].slope = tsens_8064_slope[i]; -+ s[i].offset = CAL_MDEGC - (s[i].calib_data * s[i].slope); -+ } -+ -+ hw_init(tmdev); -+ -+ return 0; -+} -+ -+static int get_temp_ipq8064(struct tsens_device *tmdev, int id, int *temp) -+{ -+ int ret; -+ u32 code, trdy; -+ const struct tsens_sensor *s = &tmdev->sensor[id]; -+ unsigned long timeout; -+ -+ timeout = jiffies + usecs_to_jiffies(TIMEOUT_US); -+ do { -+ ret = regmap_read(tmdev->map, INT_STATUS_ADDR, &trdy); -+ if (ret) -+ return ret; -+ if (!(trdy & TRDY_MASK)) -+ continue; -+ ret = regmap_read(tmdev->map, s->status, &code); -+ if (ret) -+ return ret; -+ *temp = code_to_degC(code, s); -+ return 0; -+ } while (time_before(jiffies, timeout)); -+ -+ return -ETIMEDOUT; -+} -+ -+static int set_trip_temp_ipq8064(void *data, int trip, int temp) -+{ -+ unsigned int reg_th, reg_cntl; -+ int ret, code, code_chk, hi_code, lo_code; -+ const struct tsens_sensor *s = data; -+ struct tsens_device *tmdev = s->tmdev; -+ -+ code_chk = code = degC_to_code(temp, s); -+ -+ if (code < THRESHOLD_MIN_CODE || code > THRESHOLD_MAX_CODE) -+ return -EINVAL; -+ -+ ret = regmap_read(tmdev->map, STATUS_CNTL_8064, ®_cntl); -+ if (ret) -+ return ret; -+ -+ ret = regmap_read(tmdev->map, THRESHOLD_ADDR, ®_th); -+ if (ret) -+ return ret; -+ -+ hi_code = (reg_th & THRESHOLD_UPPER_LIMIT_MASK) -+ >> THRESHOLD_UPPER_LIMIT_SHIFT; -+ lo_code = (reg_th & THRESHOLD_LOWER_LIMIT_MASK) -+ >> THRESHOLD_LOWER_LIMIT_SHIFT; -+ -+ switch (trip) { -+ case TSENS_TRIP_STAGE3: -+ code <<= THRESHOLD_MAX_LIMIT_SHIFT; -+ reg_th &= ~THRESHOLD_MAX_LIMIT_MASK; -+ break; -+ case TSENS_TRIP_STAGE2: -+ if (code_chk <= lo_code) -+ return -EINVAL; -+ code <<= THRESHOLD_UPPER_LIMIT_SHIFT; -+ reg_th &= ~THRESHOLD_UPPER_LIMIT_MASK; -+ break; -+ case TSENS_TRIP_STAGE1: -+ if (code_chk >= hi_code) -+ return -EINVAL; -+ code <<= THRESHOLD_LOWER_LIMIT_SHIFT; -+ reg_th &= ~THRESHOLD_LOWER_LIMIT_MASK; -+ break; -+ case TSENS_TRIP_STAGE0: -+ code <<= THRESHOLD_MIN_LIMIT_SHIFT; -+ reg_th &= ~THRESHOLD_MIN_LIMIT_MASK; -+ break; -+ default: -+ return -EINVAL; -+ } -+ -+ ret = regmap_write(tmdev->map, THRESHOLD_ADDR, reg_th | code); -+ if (ret) -+ return ret; -+ -+ return 0; -+} -+ -+static int set_trip_activate_ipq8064(void *data, int trip, -+ enum thermal_trip_activation_mode mode) -+{ -+ unsigned int reg_cntl, mask, val; -+ const struct tsens_sensor *s = data; -+ struct tsens_device *tmdev = s->tmdev; -+ int ret; -+ -+ if (!tmdev || trip < 0) -+ return -EINVAL; -+ -+ ret = regmap_read(tmdev->map, STATUS_CNTL_8064, ®_cntl); -+ if (ret) -+ return ret; -+ -+ switch (trip) { -+ case TSENS_TRIP_STAGE3: -+ mask = MAX_STATUS_MASK; -+ break; -+ case TSENS_TRIP_STAGE2: -+ mask = UPPER_STATUS_CLR; -+ break; -+ case TSENS_TRIP_STAGE1: -+ mask = LOWER_STATUS_CLR; -+ break; -+ case TSENS_TRIP_STAGE0: -+ mask = MIN_STATUS_MASK; -+ break; -+ default: -+ return -EINVAL; -+ } -+ -+ if (mode == THERMAL_TRIP_ACTIVATION_DISABLED) -+ val = reg_cntl | mask; -+ else -+ val = reg_cntl & ~mask; -+ -+ ret = regmap_write(tmdev->map, STATUS_CNTL_8064, val); -+ if (ret) -+ return ret; -+ -+ /* force memory to sync */ -+ mb(); -+ return 0; -+} -+ -+const struct tsens_ops ops_ipq8064 = { -+ .init = init_ipq8064, -+ .calibrate = calibrate_ipq8064, -+ .get_temp = get_temp_ipq8064, -+ .suspend = suspend_ipq8064, -+ .resume = resume_ipq8064, -+ .set_trip_temp = set_trip_temp_ipq8064, -+ .set_trip_activate = set_trip_activate_ipq8064, -+}; -+ -+const struct tsens_data data_ipq8064 = { -+ .num_sensors = 11, -+ .ops = &ops_ipq8064, -+}; ---- a/drivers/thermal/qcom/tsens.c -+++ b/drivers/thermal/qcom/tsens.c -@@ -75,8 +75,11 @@ static const struct of_device_id tsens_t - }, { - .compatible = "qcom,tsens-v2", - .data = &data_tsens_v2, -+ }, { -+ .compatible = "qcom,ipq8064-tsens", -+ .data = &data_ipq8064, - }, -- {} -+ {} - }; - MODULE_DEVICE_TABLE(of, tsens_table); - ---- a/drivers/thermal/qcom/tsens.h -+++ b/drivers/thermal/qcom/tsens.h -@@ -89,7 +89,7 @@ int init_common(struct tsens_device *); - int get_temp_common(struct tsens_device *, int, int *); - - /* TSENS v1 targets */ --extern const struct tsens_data data_8916, data_8974, data_8960; -+extern const struct tsens_data data_8916, data_8974, data_8960, data_ipq8064; - /* TSENS v2 targets */ - extern const struct tsens_data data_8996, data_tsens_v2; - diff --git a/target/linux/ipq806x/patches-4.19/0063-2-tsens-support-configurable-interrupts.patch b/target/linux/ipq806x/patches-4.19/0063-2-tsens-support-configurable-interrupts.patch deleted file mode 100644 index 62e26cbee4..0000000000 --- a/target/linux/ipq806x/patches-4.19/0063-2-tsens-support-configurable-interrupts.patch +++ /dev/null @@ -1,434 +0,0 @@ -From 4e87400732c77765afae2ea89ed43837457aa604 Mon Sep 17 00:00:00 2001 -From: Rajith Cherian -Date: Wed, 1 Feb 2017 19:00:26 +0530 -Subject: [PATCH] ipq8064: tsens: Support for configurable interrupts - -Provide support for adding configurable high and -configurable low trip temperatures. An interrupts is -also triggerred when these trip points are hit. The -interrupts can be activated or deactivated from sysfs. -This functionality is made available only if -CONFIG_THERMAL_WRITABLE_TRIPS is defined. - -Change-Id: Ib73f3f9459de4fffce7bb985a0312a88291f4934 -Signed-off-by: Rajith Cherian ---- - .../devicetree/bindings/thermal/qcom-tsens.txt | 4 ++ - drivers/thermal/of-thermal.c | 63 ++++++++++++++++++---- - drivers/thermal/qcom/tsens.c | 43 ++++++++++++--- - drivers/thermal/qcom/tsens.h | 11 ++++ - drivers/thermal/thermal_core.c | 44 ++++++++++++++- - include/linux/thermal.h | 14 +++++ - 6 files changed, 162 insertions(+), 17 deletions(-) - ---- a/drivers/thermal/of-thermal.c -+++ b/drivers/thermal/of-thermal.c -@@ -77,7 +77,7 @@ static int of_thermal_get_temp(struct th - { - struct __thermal_zone *data = tz->devdata; - -- if (!data->ops->get_temp) -+ if (!data->ops->get_temp || (data->mode == THERMAL_DEVICE_DISABLED)) - return -EINVAL; - - return data->ops->get_temp(data->sensor_data, temp); -@@ -88,7 +88,8 @@ static int of_thermal_set_trips(struct t - { - struct __thermal_zone *data = tz->devdata; - -- if (!data->ops || !data->ops->set_trips) -+ if (!data->ops || !data->ops->set_trips -+ || (data->mode == THERMAL_DEVICE_DISABLED)) - return -EINVAL; - - return data->ops->set_trips(data->sensor_data, low, high); -@@ -174,6 +175,9 @@ static int of_thermal_set_emul_temp(stru - { - struct __thermal_zone *data = tz->devdata; - -+ if (data->mode == THERMAL_DEVICE_DISABLED) -+ return -EINVAL; -+ - return data->ops->set_emul_temp(data->sensor_data, temp); - } - -@@ -182,7 +186,7 @@ static int of_thermal_get_trend(struct t - { - struct __thermal_zone *data = tz->devdata; - -- if (!data->ops->get_trend) -+ if (!data->ops->get_trend || (data->mode == THERMAL_DEVICE_DISABLED)) - return -EINVAL; - - return data->ops->get_trend(data->sensor_data, trip, trend); -@@ -271,7 +275,9 @@ static int of_thermal_set_mode(struct th - mutex_unlock(&tz->lock); - - data->mode = mode; -- thermal_zone_device_update(tz, THERMAL_EVENT_UNSPECIFIED); -+ -+ if (mode == THERMAL_DEVICE_ENABLED) -+ thermal_zone_device_update(tz, THERMAL_EVENT_UNSPECIFIED); - - return 0; - } -@@ -281,7 +287,8 @@ static int of_thermal_get_trip_type(stru - { - struct __thermal_zone *data = tz->devdata; - -- if (trip >= data->ntrips || trip < 0) -+ if (trip >= data->ntrips || trip < 0 -+ || (data->mode == THERMAL_DEVICE_DISABLED)) - return -EDOM; - - *type = data->trips[trip].type; -@@ -289,12 +296,39 @@ static int of_thermal_get_trip_type(stru - return 0; - } - -+static int of_thermal_activate_trip_type(struct thermal_zone_device *tz, -+ int trip, enum thermal_trip_activation_mode mode) -+{ -+ struct __thermal_zone *data = tz->devdata; -+ -+ if (trip >= data->ntrips || trip < 0 -+ || (data->mode == THERMAL_DEVICE_DISABLED)) -+ return -EDOM; -+ -+ /* -+ * The configurable_hi and configurable_lo trip points can be -+ * activated and deactivated. -+ */ -+ -+ if (data->ops->set_trip_activate) { -+ int ret; -+ -+ ret = data->ops->set_trip_activate(data->sensor_data, -+ trip, mode); -+ if (ret) -+ return ret; -+ } -+ -+ return 0; -+} -+ - static int of_thermal_get_trip_temp(struct thermal_zone_device *tz, int trip, - int *temp) - { - struct __thermal_zone *data = tz->devdata; - -- if (trip >= data->ntrips || trip < 0) -+ if (trip >= data->ntrips || trip < 0 -+ || (data->mode == THERMAL_DEVICE_DISABLED)) - return -EDOM; - - *temp = data->trips[trip].temperature; -@@ -307,7 +341,8 @@ static int of_thermal_set_trip_temp(stru - { - struct __thermal_zone *data = tz->devdata; - -- if (trip >= data->ntrips || trip < 0) -+ if (trip >= data->ntrips || trip < 0 -+ || (data->mode == THERMAL_DEVICE_DISABLED)) - return -EDOM; - - if (data->ops->set_trip_temp) { -@@ -329,7 +364,8 @@ static int of_thermal_get_trip_hyst(stru - { - struct __thermal_zone *data = tz->devdata; - -- if (trip >= data->ntrips || trip < 0) -+ if (trip >= data->ntrips || trip < 0 -+ || (data->mode == THERMAL_DEVICE_DISABLED)) - return -EDOM; - - *hyst = data->trips[trip].hysteresis; -@@ -342,7 +378,8 @@ static int of_thermal_set_trip_hyst(stru - { - struct __thermal_zone *data = tz->devdata; - -- if (trip >= data->ntrips || trip < 0) -+ if (trip >= data->ntrips || trip < 0 -+ || (data->mode == THERMAL_DEVICE_DISABLED)) - return -EDOM; - - /* thermal framework should take care of data->mask & (1 << trip) */ -@@ -417,6 +454,9 @@ thermal_zone_of_add_sensor(struct device - if (ops->set_emul_temp) - tzd->ops->set_emul_temp = of_thermal_set_emul_temp; - -+ if (ops->set_trip_activate) -+ tzd->ops->set_trip_activate = of_thermal_activate_trip_type; -+ - mutex_unlock(&tzd->lock); - - return tzd; -@@ -711,7 +751,10 @@ static const char * const trip_types[] = - [THERMAL_TRIP_ACTIVE] = "active", - [THERMAL_TRIP_PASSIVE] = "passive", - [THERMAL_TRIP_HOT] = "hot", -- [THERMAL_TRIP_CRITICAL] = "critical", -+ [THERMAL_TRIP_CRITICAL] = "critical_high", -+ [THERMAL_TRIP_CONFIGURABLE_HI] = "configurable_hi", -+ [THERMAL_TRIP_CONFIGURABLE_LOW] = "configurable_lo", -+ [THERMAL_TRIP_CRITICAL_LOW] = "critical_low", - }; - - /** ---- a/drivers/thermal/qcom/tsens.c -+++ b/drivers/thermal/qcom/tsens.c -@@ -31,7 +31,7 @@ static int tsens_get_temp(void *data, in - - static int tsens_get_trend(void *p, int trip, enum thermal_trend *trend) - { -- const struct tsens_sensor *s = p; -+ struct tsens_sensor *s = p; - struct tsens_device *tmdev = s->tmdev; - - if (tmdev->ops->get_trend) -@@ -40,9 +40,10 @@ static int tsens_get_trend(void *p, int - return -ENOTSUPP; - } - --static int __maybe_unused tsens_suspend(struct device *dev) -+static int __maybe_unused tsens_suspend(void *data) - { -- struct tsens_device *tmdev = dev_get_drvdata(dev); -+ struct tsens_sensor *s = data; -+ struct tsens_device *tmdev = s->tmdev; - - if (tmdev->ops && tmdev->ops->suspend) - return tmdev->ops->suspend(tmdev); -@@ -50,9 +51,10 @@ static int __maybe_unused tsens_suspend - return 0; - } - --static int __maybe_unused tsens_resume(struct device *dev) -+static int __maybe_unused tsens_resume(void *data) - { -- struct tsens_device *tmdev = dev_get_drvdata(dev); -+ struct tsens_sensor *s = data; -+ struct tsens_device *tmdev = s->tmdev; - - if (tmdev->ops && tmdev->ops->resume) - return tmdev->ops->resume(tmdev); -@@ -60,6 +62,30 @@ static int __maybe_unused tsens_resume(s - return 0; - } - -+static int __maybe_unused tsens_set_trip_temp(void *data, int trip, int temp) -+{ -+ struct tsens_sensor *s = data; -+ struct tsens_device *tmdev = s->tmdev; -+ -+ if (tmdev->ops && tmdev->ops->set_trip_temp) -+ return tmdev->ops->set_trip_temp(s, trip, temp); -+ -+ return 0; -+} -+ -+static int __maybe_unused tsens_activate_trip_type(void *data, int trip, -+ enum thermal_trip_activation_mode mode) -+{ -+ struct tsens_sensor *s = data; -+ struct tsens_device *tmdev = s->tmdev; -+ -+ if (tmdev->ops && tmdev->ops->set_trip_activate) -+ return tmdev->ops->set_trip_activate(s, trip, mode); -+ -+ return 0; -+} -+ -+ - static SIMPLE_DEV_PM_OPS(tsens_pm_ops, tsens_suspend, tsens_resume); - - static const struct of_device_id tsens_table[] = { -@@ -86,6 +112,8 @@ MODULE_DEVICE_TABLE(of, tsens_table); - static const struct thermal_zone_of_device_ops tsens_of_ops = { - .get_temp = tsens_get_temp, - .get_trend = tsens_get_trend, -+ .set_trip_temp = tsens_set_trip_temp, -+ .set_trip_activate = tsens_activate_trip_type, - }; - - static int tsens_register(struct tsens_device *tmdev) -@@ -134,7 +162,7 @@ static int tsens_probe(struct platform_d - if (id) - data = id->data; - else -- data = &data_8960; -+ return -EINVAL; - - num_sensors = data->num_sensors; - -@@ -155,6 +183,9 @@ static int tsens_probe(struct platform_d - tmdev->dev = dev; - tmdev->num_sensors = num_sensors; - tmdev->ops = data->ops; -+ -+ tmdev->tsens_irq = platform_get_irq(pdev, 0); -+ - for (i = 0; i < tmdev->num_sensors; i++) { - if (data->hw_ids) - tmdev->sensor[i].hw_id = data->hw_ids[i]; ---- a/drivers/thermal/qcom/tsens.h -+++ b/drivers/thermal/qcom/tsens.h -@@ -24,9 +24,12 @@ struct tsens_device; - struct tsens_sensor { - struct tsens_device *tmdev; - struct thermal_zone_device *tzd; -+ struct work_struct notify_work; - int offset; - int id; - int hw_id; -+ int calib_data; -+ int calib_data_backup; - int slope; - u32 status; - }; -@@ -41,6 +44,9 @@ struct tsens_sensor { - * @suspend: Function to suspend the tsens device - * @resume: Function to resume the tsens device - * @get_trend: Function to get the thermal/temp trend -+ * @set_trip_temp: Function to set trip temp -+ * @get_trip_temp: Function to get trip temp -+ * @set_trip_activate: Function to activate trip points - */ - struct tsens_ops { - /* mandatory callbacks */ -@@ -53,6 +59,9 @@ struct tsens_ops { - int (*suspend)(struct tsens_device *); - int (*resume)(struct tsens_device *); - int (*get_trend)(struct tsens_device *, int, enum thermal_trend *); -+ int (*set_trip_temp)(void *, int, int); -+ int (*set_trip_activate)(void *, int, -+ enum thermal_trip_activation_mode); - }; - - /** -@@ -76,10 +85,12 @@ struct tsens_context { - struct tsens_device { - struct device *dev; - u32 num_sensors; -+ u32 tsens_irq; - struct regmap *map; - u32 tm_offset; - struct tsens_context ctx; - const struct tsens_ops *ops; -+ struct work_struct tsens_work; - struct tsens_sensor sensor[0]; - }; - ---- a/drivers/thermal/thermal_sysfs.c -+++ b/drivers/thermal/thermal_sysfs.c -@@ -113,12 +113,48 @@ trip_point_type_show(struct device *dev, - return sprintf(buf, "passive\n"); - case THERMAL_TRIP_ACTIVE: - return sprintf(buf, "active\n"); -+ case THERMAL_TRIP_CONFIGURABLE_HI: -+ return sprintf(buf, "configurable_hi\n"); -+ case THERMAL_TRIP_CONFIGURABLE_LOW: -+ return sprintf(buf, "configurable_low\n"); -+ case THERMAL_TRIP_CRITICAL_LOW: -+ return sprintf(buf, "critical_low\n"); - default: - return sprintf(buf, "unknown\n"); - } - } - - static ssize_t -+trip_point_type_activate(struct device *dev, struct device_attribute *attr, -+ const char *buf, size_t count) -+{ -+ struct thermal_zone_device *tz = to_thermal_zone(dev); -+ int trip, ret; -+ char *enabled = "enabled"; -+ char *disabled = "disabled"; -+ -+ if (!tz->ops->set_trip_activate) -+ return -EPERM; -+ -+ if (!sscanf(attr->attr.name, "trip_point_%d_type", &trip)) -+ return -EINVAL; -+ -+ if (!strncmp(buf, enabled, strlen(enabled))) -+ ret = tz->ops->set_trip_activate(tz, trip, -+ THERMAL_TRIP_ACTIVATION_ENABLED); -+ else if (!strncmp(buf, disabled, strlen(disabled))) -+ ret = tz->ops->set_trip_activate(tz, trip, -+ THERMAL_TRIP_ACTIVATION_DISABLED); -+ else -+ ret = -EINVAL; -+ -+ if (ret) -+ return ret; -+ -+ return count; -+} -+ -+static ssize_t - trip_point_temp_store(struct device *dev, struct device_attribute *attr, - const char *buf, size_t count) - { -@@ -559,6 +595,12 @@ static int create_trip_attrs(struct ther - tz->trip_type_attrs[indx].attr.show = trip_point_type_show; - attrs[indx] = &tz->trip_type_attrs[indx].attr.attr; - -+ if (IS_ENABLED(CONFIG_THERMAL_WRITABLE_TRIPS)) { -+ tz->trip_type_attrs[indx].attr.store -+ = trip_point_type_activate; -+ tz->trip_type_attrs[indx].attr.attr.mode |= S_IWUSR; -+ } -+ - /* create trip temp attribute */ - snprintf(tz->trip_temp_attrs[indx].name, THERMAL_NAME_LENGTH, - "trip_point_%d_temp", indx); ---- a/include/linux/thermal.h -+++ b/include/linux/thermal.h -@@ -63,11 +63,19 @@ enum thermal_device_mode { - THERMAL_DEVICE_ENABLED, - }; - -+enum thermal_trip_activation_mode { -+ THERMAL_TRIP_ACTIVATION_DISABLED = 0, -+ THERMAL_TRIP_ACTIVATION_ENABLED, -+}; -+ - enum thermal_trip_type { - THERMAL_TRIP_ACTIVE = 0, - THERMAL_TRIP_PASSIVE, - THERMAL_TRIP_HOT, - THERMAL_TRIP_CRITICAL, -+ THERMAL_TRIP_CONFIGURABLE_HI, -+ THERMAL_TRIP_CONFIGURABLE_LOW, -+ THERMAL_TRIP_CRITICAL_LOW, - }; - - enum thermal_trend { -@@ -105,6 +113,8 @@ struct thermal_zone_device_ops { - enum thermal_trip_type *); - int (*get_trip_temp) (struct thermal_zone_device *, int, int *); - int (*set_trip_temp) (struct thermal_zone_device *, int, int); -+ int (*set_trip_activate) (struct thermal_zone_device *, int, -+ enum thermal_trip_activation_mode); - int (*get_trip_hyst) (struct thermal_zone_device *, int, int *); - int (*set_trip_hyst) (struct thermal_zone_device *, int, int); - int (*get_crit_temp) (struct thermal_zone_device *, int *); -@@ -349,6 +359,8 @@ struct thermal_genl_event { - * temperature. - * @set_trip_temp: a pointer to a function that sets the trip temperature on - * hardware. -+ * @activate_trip_type: a pointer to a function to enable/disable trip -+ * temperature interrupts - */ - struct thermal_zone_of_device_ops { - int (*get_temp)(void *, int *); -@@ -356,6 +368,8 @@ struct thermal_zone_of_device_ops { - int (*set_trips)(void *, int, int); - int (*set_emul_temp)(void *, int); - int (*set_trip_temp)(void *, int, int); -+ int (*set_trip_activate)(void *, int, -+ enum thermal_trip_activation_mode); - }; - - /** diff --git a/target/linux/ipq806x/patches-4.19/0063-3-tsens-fix-kernel-4_19.patch b/target/linux/ipq806x/patches-4.19/0063-3-tsens-fix-kernel-4_19.patch deleted file mode 100644 index a870692906..0000000000 --- a/target/linux/ipq806x/patches-4.19/0063-3-tsens-fix-kernel-4_19.patch +++ /dev/null @@ -1,20 +0,0 @@ ---- a/drivers/thermal/qcom/tsens-common.c -+++ b/drivers/thermal/qcom/tsens-common.c -@@ -128,6 +128,7 @@ int __init init_common(struct tsens_devi - { - void __iomem *base; - struct resource *res; -+ resource_size_t size; - struct platform_device *op = of_find_device_by_node(tmdev->dev->of_node); - - if (!op) -@@ -142,7 +143,8 @@ int __init init_common(struct tsens_devi - } - - res = platform_get_resource(op, IORESOURCE_MEM, 0); -- base = devm_ioremap_resource(&op->dev, res); -+ size = resource_size(res); -+ base = devm_ioremap(&op->dev, res->start, size); - if (IS_ERR(base)) - return PTR_ERR(base); - diff --git a/target/linux/ipq806x/patches-4.19/0063-4-ip806x-tsense-rework-driver.patch b/target/linux/ipq806x/patches-4.19/0063-4-ip806x-tsense-rework-driver.patch deleted file mode 100644 index 951145b3de..0000000000 --- a/target/linux/ipq806x/patches-4.19/0063-4-ip806x-tsense-rework-driver.patch +++ /dev/null @@ -1,107 +0,0 @@ ---- a/drivers/thermal/qcom/tsens-ipq8064.c -+++ b/drivers/thermal/qcom/tsens-ipq8064.c -@@ -13,10 +13,12 @@ - */ - - #include -+#include - #include - #include - #include - #include -+#include - #include - #include - #include -@@ -210,9 +212,8 @@ static void tsens_scheduler_fn(struct wo - struct tsens_device *tmdev = container_of(work, struct tsens_device, - tsens_work); - unsigned int threshold, threshold_low, code, reg, sensor, mask; -- unsigned int sensor_addr; - bool upper_th_x, lower_th_x; -- int adc_code, ret; -+ int ret; - - ret = regmap_read(tmdev->map, STATUS_CNTL_8064, ®); - if (ret) -@@ -261,9 +262,8 @@ static void tsens_scheduler_fn(struct wo - if (upper_th_x || lower_th_x) { - /* Notify user space */ - schedule_work(&tmdev->sensor[0].notify_work); -- regmap_read(tmdev->map, sensor_addr, &adc_code); - pr_debug("Trigger (%d degrees) for sensor %d\n", -- code_to_degC(adc_code, &tmdev->sensor[0]), 0); -+ code_to_degC(code, &tmdev->sensor[0]), 0); - } - } - regmap_write(tmdev->map, STATUS_CNTL_8064, reg & mask); -@@ -372,40 +372,55 @@ static int init_ipq8064(struct tsens_dev - static int calibrate_ipq8064(struct tsens_device *tmdev) - { - int i; -- char *data, *data_backup; -- -+ int ret = 0; -+ u8 *data, *data_backup; -+ struct device *dev = tmdev->dev; - ssize_t num_read = tmdev->num_sensors; - struct tsens_sensor *s = tmdev->sensor; - -- data = qfprom_read(tmdev->dev, "calib"); -+ data = qfprom_read(dev, "calib"); - if (IS_ERR(data)) { -- pr_err("Calibration not found.\n"); -- return PTR_ERR(data); -+ ret = PTR_ERR(data); -+ if (ret != -EPROBE_DEFER) -+ dev_err(dev, "Calibration not found."); -+ goto exit; - } - -- data_backup = qfprom_read(tmdev->dev, "calib_backup"); -+ data_backup = qfprom_read(dev, "calib_backup"); - if (IS_ERR(data_backup)) { -- pr_err("Backup calibration not found.\n"); -- return PTR_ERR(data_backup); -+ ret = PTR_ERR(data_backup); -+ if (ret != -EPROBE_DEFER) -+ dev_err(dev, "Backup Calibration not found."); -+ goto free_data; - } - - for (i = 0; i < num_read; i++) { - s[i].calib_data = readb_relaxed(data + i); -- s[i].calib_data_backup = readb_relaxed(data_backup + i); -+ -+ if (!s[i].calib_data) { -+ s[i].calib_data_backup = readb_relaxed(data_backup + i); -+ -+ if (!s[i].calib_data_backup) { -+ dev_err(dev, "QFPROM TSENS calibration data not present"); -+ ret = -ENODEV; -+ goto free_backup; -+ } - -- if (s[i].calib_data_backup) - s[i].calib_data = s[i].calib_data_backup; -- if (!s[i].calib_data) { -- pr_err("QFPROM TSENS calibration data not present\n"); -- return -ENODEV; - } -+ - s[i].slope = tsens_8064_slope[i]; - s[i].offset = CAL_MDEGC - (s[i].calib_data * s[i].slope); - } - - hw_init(tmdev); - -- return 0; -+free_backup: -+ kfree(data_backup); -+free_data: -+ kfree(data); -+exit: -+ return ret; - } - - static int get_temp_ipq8064(struct tsens_device *tmdev, int id, int *temp) diff --git a/target/linux/ipq806x/patches-4.19/0064-clk-clk-rpm-fixes.patch b/target/linux/ipq806x/patches-4.19/0064-clk-clk-rpm-fixes.patch deleted file mode 100644 index 72217de12e..0000000000 --- a/target/linux/ipq806x/patches-4.19/0064-clk-clk-rpm-fixes.patch +++ /dev/null @@ -1,95 +0,0 @@ -From d30840e2b1cf79d90392e6051b0c0b6006d29d8b Mon Sep 17 00:00:00 2001 -From: John Crispin -Date: Thu, 9 Mar 2017 09:32:40 +0100 -Subject: [PATCH 64/69] clk: clk-rpm fixes - -Signed-off-by: John Crispin ---- - .../devicetree/bindings/clock/qcom,rpmcc.txt | 1 + - drivers/clk/qcom/clk-rpm.c | 35 ++++++++++++++++++++++ - include/dt-bindings/clock/qcom,rpmcc.h | 4 +++ - 3 files changed, 40 insertions(+) - ---- a/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt -+++ b/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt -@@ -16,6 +16,7 @@ Required properties : - "qcom,rpmcc-msm8974", "qcom,rpmcc" - "qcom,rpmcc-apq8064", "qcom,rpmcc" - "qcom,rpmcc-msm8996", "qcom,rpmcc" -+ "qcom,rpmcc-ipq806x", "qcom,rpmcc" - - - #clock-cells : shall contain 1 - ---- a/include/dt-bindings/clock/qcom,rpmcc.h -+++ b/include/dt-bindings/clock/qcom,rpmcc.h -@@ -45,6 +45,10 @@ - #define RPM_XO_A0 27 - #define RPM_XO_A1 28 - #define RPM_XO_A2 29 -+#define RPM_NSS_FABRIC_0_CLK 30 -+#define RPM_NSS_FABRIC_0_A_CLK 31 -+#define RPM_NSS_FABRIC_1_CLK 32 -+#define RPM_NSS_FABRIC_1_A_CLK 33 - - /* SMD RPM clocks */ - #define RPM_SMD_XO_CLK_SRC 0 ---- a/drivers/clk/qcom/clk-rpm.c -+++ b/drivers/clk/qcom/clk-rpm.c -@@ -520,6 +520,16 @@ DEFINE_CLK_RPM_XO_BUFFER(apq8064, xo_a0_ - DEFINE_CLK_RPM_XO_BUFFER(apq8064, xo_a1_clk, xo_a1_a_clk, 24); - DEFINE_CLK_RPM_XO_BUFFER(apq8064, xo_a2_clk, xo_a2_a_clk, 28); - -+/* ipq806x */ -+DEFINE_CLK_RPM(ipq806x, afab_clk, afab_a_clk, QCOM_RPM_APPS_FABRIC_CLK); -+DEFINE_CLK_RPM(ipq806x, cfpb_clk, cfpb_a_clk, QCOM_RPM_CFPB_CLK); -+DEFINE_CLK_RPM(ipq806x, daytona_clk, daytona_a_clk, QCOM_RPM_DAYTONA_FABRIC_CLK); -+DEFINE_CLK_RPM(ipq806x, ebi1_clk, ebi1_a_clk, QCOM_RPM_EBI1_CLK); -+DEFINE_CLK_RPM(ipq806x, sfab_clk, sfab_a_clk, QCOM_RPM_SYS_FABRIC_CLK); -+DEFINE_CLK_RPM(ipq806x, sfpb_clk, sfpb_a_clk, QCOM_RPM_SFPB_CLK); -+DEFINE_CLK_RPM(ipq806x, nss_fabric_0_clk, nss_fabric_0_a_clk, QCOM_RPM_NSS_FABRIC_0_CLK); -+DEFINE_CLK_RPM(ipq806x, nss_fabric_1_clk, nss_fabric_1_a_clk, QCOM_RPM_NSS_FABRIC_1_CLK); -+ - static struct clk_rpm *apq8064_clks[] = { - [RPM_APPS_FABRIC_CLK] = &apq8064_afab_clk, - [RPM_APPS_FABRIC_A_CLK] = &apq8064_afab_a_clk, -@@ -546,15 +556,40 @@ static struct clk_rpm *apq8064_clks[] = - [RPM_XO_A2] = &apq8064_xo_a2_clk, - }; - -+static struct clk_rpm *ipq806x_clks[] = { -+ [RPM_APPS_FABRIC_CLK] = &ipq806x_afab_clk, -+ [RPM_APPS_FABRIC_A_CLK] = &ipq806x_afab_a_clk, -+ [RPM_CFPB_CLK] = &ipq806x_cfpb_clk, -+ [RPM_CFPB_A_CLK] = &ipq806x_cfpb_a_clk, -+ [RPM_DAYTONA_FABRIC_CLK] = &ipq806x_daytona_clk, -+ [RPM_DAYTONA_FABRIC_A_CLK] = &ipq806x_daytona_a_clk, -+ [RPM_EBI1_CLK] = &ipq806x_ebi1_clk, -+ [RPM_EBI1_A_CLK] = &ipq806x_ebi1_a_clk, -+ [RPM_SYS_FABRIC_CLK] = &ipq806x_sfab_clk, -+ [RPM_SYS_FABRIC_A_CLK] = &ipq806x_sfab_a_clk, -+ [RPM_SFPB_CLK] = &ipq806x_sfpb_clk, -+ [RPM_SFPB_A_CLK] = &ipq806x_sfpb_a_clk, -+ [RPM_NSS_FABRIC_0_CLK] = &ipq806x_nss_fabric_0_clk, -+ [RPM_NSS_FABRIC_0_A_CLK] = &ipq806x_nss_fabric_0_a_clk, -+ [RPM_NSS_FABRIC_1_CLK] = &ipq806x_nss_fabric_1_clk, -+ [RPM_NSS_FABRIC_1_A_CLK] = &ipq806x_nss_fabric_1_a_clk, -+}; -+ - static const struct rpm_clk_desc rpm_clk_apq8064 = { - .clks = apq8064_clks, - .num_clks = ARRAY_SIZE(apq8064_clks), - }; - -+static const struct rpm_clk_desc rpm_clk_ipq806x = { -+ .clks = ipq806x_clks, -+ .num_clks = ARRAY_SIZE(ipq806x_clks), -+}; -+ - static const struct of_device_id rpm_clk_match_table[] = { - { .compatible = "qcom,rpmcc-msm8660", .data = &rpm_clk_msm8660 }, - { .compatible = "qcom,rpmcc-apq8060", .data = &rpm_clk_msm8660 }, - { .compatible = "qcom,rpmcc-apq8064", .data = &rpm_clk_apq8064 }, -+ { .compatible = "qcom,rpmcc-ipq806x", .data = &rpm_clk_ipq806x }, - { } - }; - MODULE_DEVICE_TABLE(of, rpm_clk_match_table); diff --git a/target/linux/ipq806x/patches-4.19/0065-arm-override-compiler-flags.patch b/target/linux/ipq806x/patches-4.19/0065-arm-override-compiler-flags.patch deleted file mode 100644 index 6f1cdcf4d6..0000000000 --- a/target/linux/ipq806x/patches-4.19/0065-arm-override-compiler-flags.patch +++ /dev/null @@ -1,21 +0,0 @@ -From 4d8e29642661397a339ac3485f212c6360445421 Mon Sep 17 00:00:00 2001 -From: John Crispin -Date: Thu, 9 Mar 2017 09:33:32 +0100 -Subject: [PATCH 65/69] arm: override compiler flags - -Signed-off-by: John Crispin ---- - arch/arm/Makefile | 2 +- - 1 file changed, 1 insertion(+), 1 deletion(-) - ---- a/arch/arm/Makefile -+++ b/arch/arm/Makefile -@@ -64,7 +64,7 @@ KBUILD_CFLAGS += $(call cc-option,-fno-i - # macro, but instead defines a whole series of macros which makes - # testing for a specific architecture or later rather impossible. - arch-$(CONFIG_CPU_32v7M) =-D__LINUX_ARM_ARCH__=7 -march=armv7-m -Wa,-march=armv7-m --arch-$(CONFIG_CPU_32v7) =-D__LINUX_ARM_ARCH__=7 $(call cc-option,-march=armv7-a,-march=armv5t -Wa$(comma)-march=armv7-a) -+arch-$(CONFIG_CPU_32v7) =-D__LINUX_ARM_ARCH__=7 -mcpu=cortex-a15 - arch-$(CONFIG_CPU_32v6) =-D__LINUX_ARM_ARCH__=6 $(call cc-option,-march=armv6,-march=armv5t -Wa$(comma)-march=armv6) - # Only override the compiler option if ARMv6. The ARMv6K extensions are - # always available in ARMv7 diff --git a/target/linux/ipq806x/patches-4.19/0067-generic-Mangle-bootloader-s-kernel-arguments.patch b/target/linux/ipq806x/patches-4.19/0067-generic-Mangle-bootloader-s-kernel-arguments.patch deleted file mode 100644 index b7b9c991e0..0000000000 --- a/target/linux/ipq806x/patches-4.19/0067-generic-Mangle-bootloader-s-kernel-arguments.patch +++ /dev/null @@ -1,189 +0,0 @@ -From 71270226b14733a4b1f2cde58ea9265caa50b38d Mon Sep 17 00:00:00 2001 -From: Adrian Panella -Date: Thu, 9 Mar 2017 09:37:17 +0100 -Subject: [PATCH 67/69] generic: Mangle bootloader's kernel arguments - -The command-line arguments provided by the boot loader will be -appended to a new device tree property: bootloader-args. -If there is a property "append-rootblock" in DT under /chosen -and a root= option in bootloaders command line it will be parsed -and added to DT bootargs with the form: XX. -Only command line ATAG will be processed, the rest of the ATAGs -sent by bootloader will be ignored. -This is usefull in dual boot systems, to get the current root partition -without afecting the rest of the system. - -Signed-off-by: Adrian Panella ---- - arch/arm/Kconfig | 11 +++++ - arch/arm/boot/compressed/atags_to_fdt.c | 72 ++++++++++++++++++++++++++++++++- - init/main.c | 16 ++++++++ - 3 files changed, 98 insertions(+), 1 deletion(-) - ---- a/arch/arm/Kconfig -+++ b/arch/arm/Kconfig -@@ -1926,6 +1926,17 @@ config ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEN - The command-line arguments provided by the boot loader will be - appended to the the device tree bootargs property. - -+config ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE -+ bool "Append rootblock parsing bootloader's kernel arguments" -+ help -+ The command-line arguments provided by the boot loader will be -+ appended to a new device tree property: bootloader-args. -+ If there is a property "append-rootblock" in DT under /chosen -+ and a root= option in bootloaders command line it will be parsed -+ and added to DT bootargs with the form: XX. -+ Only command line ATAG will be processed, the rest of the ATAGs -+ sent by bootloader will be ignored. -+ - endchoice - - config CMDLINE ---- a/arch/arm/boot/compressed/atags_to_fdt.c -+++ b/arch/arm/boot/compressed/atags_to_fdt.c -@@ -4,6 +4,8 @@ - - #if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND) - #define do_extend_cmdline 1 -+#elif defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE) -+#define do_extend_cmdline 1 - #else - #define do_extend_cmdline 0 - #endif -@@ -67,6 +69,59 @@ static uint32_t get_cell_size(const void - return cell_size; - } - -+#if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE) -+ -+static char *append_rootblock(char *dest, const char *str, int len, void *fdt) -+{ -+ char *ptr, *end; -+ char *root="root="; -+ int i, l; -+ const char *rootblock; -+ -+ //ARM doesn't have __HAVE_ARCH_STRSTR, so search manually -+ ptr = str - 1; -+ -+ do { -+ //first find an 'r' at the begining or after a space -+ do { -+ ptr++; -+ ptr = strchr(ptr, 'r'); -+ if(!ptr) return dest; -+ -+ } while (ptr != str && *(ptr-1) != ' '); -+ -+ //then check for the rest -+ for(i = 1; i <= 4; i++) -+ if(*(ptr+i) != *(root+i)) break; -+ -+ } while (i != 5); -+ -+ end = strchr(ptr, ' '); -+ end = end ? (end - 1) : (strchr(ptr, 0) - 1); -+ -+ //find partition number (assumes format root=/dev/mtdXX | /dev/mtdblockXX | yy:XX ) -+ for( i = 0; end >= ptr && *end >= '0' && *end <= '9'; end--, i++); -+ ptr = end + 1; -+ -+ /* if append-rootblock property is set use it to append to command line */ -+ rootblock = getprop(fdt, "/chosen", "append-rootblock", &l); -+ if(rootblock != NULL) { -+ if(*dest != ' ') { -+ *dest = ' '; -+ dest++; -+ len++; -+ } -+ if (len + l + i <= COMMAND_LINE_SIZE) { -+ memcpy(dest, rootblock, l); -+ dest += l - 1; -+ memcpy(dest, ptr, i); -+ dest += i; -+ } -+ } -+ return dest; -+} -+#endif -+ - static void merge_fdt_bootargs(void *fdt, const char *fdt_cmdline) - { - char cmdline[COMMAND_LINE_SIZE]; -@@ -86,12 +141,21 @@ static void merge_fdt_bootargs(void *fdt - - /* and append the ATAG_CMDLINE */ - if (fdt_cmdline) { -+ -+#if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE) -+ //save original bootloader args -+ //and append ubi.mtd with root partition number to current cmdline -+ setprop_string(fdt, "/chosen", "bootloader-args", fdt_cmdline); -+ ptr = append_rootblock(ptr, fdt_cmdline, len, fdt); -+ -+#else - len = strlen(fdt_cmdline); - if (ptr - cmdline + len + 2 < COMMAND_LINE_SIZE) { - *ptr++ = ' '; - memcpy(ptr, fdt_cmdline, len); - ptr += len; - } -+#endif - } - *ptr = '\0'; - -@@ -148,7 +212,9 @@ int atags_to_fdt(void *atag_list, void * - else - setprop_string(fdt, "/chosen", "bootargs", - atag->u.cmdline.cmdline); -- } else if (atag->hdr.tag == ATAG_MEM) { -+ } -+#ifndef CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE -+ else if (atag->hdr.tag == ATAG_MEM) { - if (memcount >= sizeof(mem_reg_property)/4) - continue; - if (!atag->u.mem.size) -@@ -187,6 +253,10 @@ int atags_to_fdt(void *atag_list, void * - setprop(fdt, "/memory", "reg", mem_reg_property, - 4 * memcount * memsize); - } -+#else -+ -+ } -+#endif - - return fdt_pack(fdt); - } ---- a/init/main.c -+++ b/init/main.c -@@ -102,6 +102,10 @@ - #define CREATE_TRACE_POINTS - #include - -+#if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE) -+#include -+#endif -+ - static int kernel_init(void *); - - extern void init_IRQ(void); -@@ -593,6 +597,18 @@ asmlinkage __visible void __init start_k - pr_notice("Kernel command line: %s\n", boot_command_line); - /* parameters may set static keys */ - jump_label_init(); -+ -+#if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE) -+ //Show bootloader's original command line for reference -+ if(of_chosen) { -+ const char *prop = of_get_property(of_chosen, "bootloader-args", NULL); -+ if(prop) -+ pr_notice("Bootloader command line (ignored): %s\n", prop); -+ else -+ pr_notice("Bootloader command line not present\n"); -+ } -+#endif -+ - parse_early_param(); - after_dashes = parse_args("Booting kernel", - static_command_line, __start___param, diff --git a/target/linux/ipq806x/patches-4.19/0069-arm-boot-add-dts-files.patch b/target/linux/ipq806x/patches-4.19/0069-arm-boot-add-dts-files.patch deleted file mode 100644 index 77ce4c4245..0000000000 --- a/target/linux/ipq806x/patches-4.19/0069-arm-boot-add-dts-files.patch +++ /dev/null @@ -1,31 +0,0 @@ -From 8f68331e14dff9a101f2d0e1d6bec84a031f27ee Mon Sep 17 00:00:00 2001 -From: John Crispin -Date: Thu, 9 Mar 2017 11:03:18 +0100 -Subject: [PATCH 69/69] arm: boot: add dts files - -Signed-off-by: John Crispin ---- - arch/arm/boot/dts/Makefile | 8 ++++++++ - 1 file changed, 8 insertions(+) - ---- a/arch/arm/boot/dts/Makefile -+++ b/arch/arm/boot/dts/Makefile -@@ -791,6 +791,18 @@ dtb-$(CONFIG_ARCH_QCOM) += \ - qcom-ipq4019-ap.dk07.1-c1.dtb \ - qcom-ipq4019-ap.dk07.1-c2.dtb \ - qcom-ipq8064-ap148.dtb \ -+ qcom-ipq8064-c2600.dtb \ -+ qcom-ipq8064-d7800.dtb \ -+ qcom-ipq8064-db149.dtb \ -+ qcom-ipq8064-ap161.dtb \ -+ qcom-ipq8064-ea8500.dtb \ -+ qcom-ipq8064-r7500.dtb \ -+ qcom-ipq8064-r7500v2.dtb \ -+ qcom-ipq8064-wg2600hp.dtb \ -+ qcom-ipq8064-wpq864.dtb \ -+ qcom-ipq8064-wxr-2533dhp.dtb \ -+ qcom-ipq8065-nbg6817.dtb \ -+ qcom-ipq8065-r7800.dtb \ - qcom-msm8660-surf.dtb \ - qcom-msm8960-cdp.dtb \ - qcom-msm8974-fairphone-fp2.dtb \ diff --git a/target/linux/ipq806x/patches-4.19/0070-qcom-spm-fix-probe-order.patch b/target/linux/ipq806x/patches-4.19/0070-qcom-spm-fix-probe-order.patch deleted file mode 100644 index b7e375dfb2..0000000000 --- a/target/linux/ipq806x/patches-4.19/0070-qcom-spm-fix-probe-order.patch +++ /dev/null @@ -1,16 +0,0 @@ -Check for SCM availability before attempting to use SPM - -Signed-off-by: Felix Fietkau - ---- a/drivers/soc/qcom/spm.c -+++ b/drivers/soc/qcom/spm.c -@@ -219,6 +219,9 @@ static int __init qcom_cpuidle_init(stru - cpumask_t mask; - bool use_scm_power_down = false; - -+ if (!qcom_scm_is_available()) -+ return -EPROBE_DEFER; -+ - for (i = 0; ; i++) { - state_node = of_parse_phandle(cpu_node, "cpu-idle-states", i); - if (!state_node) diff --git a/target/linux/ipq806x/patches-4.19/0071-1-PCI-qcom-Fixed-IPQ806x-specific-clocks.patch b/target/linux/ipq806x/patches-4.19/0071-1-PCI-qcom-Fixed-IPQ806x-specific-clocks.patch deleted file mode 100644 index 3a3e0a0000..0000000000 --- a/target/linux/ipq806x/patches-4.19/0071-1-PCI-qcom-Fixed-IPQ806x-specific-clocks.patch +++ /dev/null @@ -1,93 +0,0 @@ -From 86655aa14304ca88a8ce8847276147dbc1a83238 Mon Sep 17 00:00:00 2001 -From: Sham Muthayyan -Date: Tue, 19 Jul 2016 18:44:49 +0530 -Subject: PCI: qcom: Fixed IPQ806x specific clocks - -Change-Id: I488e1bc707d6a22b37a338f41935e3922009ba5e -Signed-off-by: Sham Muthayyan ---- - ---- a/drivers/pci/controller/dwc/pcie-qcom.c -+++ b/drivers/pci/controller/dwc/pcie-qcom.c -@@ -85,6 +85,8 @@ struct qcom_pcie_resources_2_1_0 { - struct clk *iface_clk; - struct clk *core_clk; - struct clk *phy_clk; -+ struct clk *aux_clk; -+ struct clk *ref_clk; - struct reset_control *pci_reset; - struct reset_control *axi_reset; - struct reset_control *ahb_reset; -@@ -235,6 +237,14 @@ static int qcom_pcie_get_resources_2_1_0 - if (IS_ERR(res->phy_clk)) - return PTR_ERR(res->phy_clk); - -+ res->aux_clk = devm_clk_get(dev, "aux"); -+ if (IS_ERR(res->aux_clk)) -+ return PTR_ERR(res->aux_clk); -+ -+ res->ref_clk = devm_clk_get(dev, "ref"); -+ if (IS_ERR(res->ref_clk)) -+ return PTR_ERR(res->ref_clk); -+ - res->pci_reset = devm_reset_control_get_exclusive(dev, "pci"); - if (IS_ERR(res->pci_reset)) - return PTR_ERR(res->pci_reset); -@@ -267,6 +277,8 @@ static void qcom_pcie_deinit_2_1_0(struc - clk_disable_unprepare(res->iface_clk); - clk_disable_unprepare(res->core_clk); - clk_disable_unprepare(res->phy_clk); -+ clk_disable_unprepare(res->aux_clk); -+ clk_disable_unprepare(res->ref_clk); - regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies); - } - -@@ -296,16 +308,28 @@ static int qcom_pcie_init_2_1_0(struct q - goto err_assert_ahb; - } - -+ ret = clk_prepare_enable(res->core_clk); -+ if (ret) { -+ dev_err(dev, "cannot prepare/enable core clock\n"); -+ goto err_clk_core; -+ } -+ - ret = clk_prepare_enable(res->phy_clk); - if (ret) { - dev_err(dev, "cannot prepare/enable phy clock\n"); - goto err_clk_phy; - } - -- ret = clk_prepare_enable(res->core_clk); -+ ret = clk_prepare_enable(res->aux_clk); - if (ret) { -- dev_err(dev, "cannot prepare/enable core clock\n"); -- goto err_clk_core; -+ dev_err(dev, "cannot prepare/enable aux clock\n"); -+ goto err_clk_aux; -+ } -+ -+ ret = clk_prepare_enable(res->ref_clk); -+ if (ret) { -+ dev_err(dev, "cannot prepare/enable ref clock\n"); -+ goto err_clk_ref; - } - - ret = reset_control_deassert(res->ahb_reset); -@@ -361,10 +385,14 @@ static int qcom_pcie_init_2_1_0(struct q - return 0; - - err_deassert_ahb: -- clk_disable_unprepare(res->core_clk); --err_clk_core: -+ clk_disable_unprepare(res->ref_clk); -+err_clk_ref: -+ clk_disable_unprepare(res->aux_clk); -+err_clk_aux: - clk_disable_unprepare(res->phy_clk); - err_clk_phy: -+ clk_disable_unprepare(res->core_clk); -+err_clk_core: - clk_disable_unprepare(res->iface_clk); - err_assert_ahb: - regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies); diff --git a/target/linux/ipq806x/patches-4.19/0071-2-PCI-qcom-Fixed-IPQ806x-PCIE-reset-changes.patch b/target/linux/ipq806x/patches-4.19/0071-2-PCI-qcom-Fixed-IPQ806x-PCIE-reset-changes.patch deleted file mode 100644 index 5bd865a42e..0000000000 --- a/target/linux/ipq806x/patches-4.19/0071-2-PCI-qcom-Fixed-IPQ806x-PCIE-reset-changes.patch +++ /dev/null @@ -1,62 +0,0 @@ -From 490d103232287eb51c92c49a4ef8865fd0a9d59e Mon Sep 17 00:00:00 2001 -From: Sham Muthayyan -Date: Tue, 19 Jul 2016 18:58:18 +0530 -Subject: PCI: qcom: Fixed IPQ806x PCIE reset changes - -Change-Id: Ia6590e960b9754b1e8b7a51f318788cd63e9e321 -Signed-off-by: Sham Muthayyan ---- - ---- a/drivers/pci/controller/dwc/pcie-qcom.c -+++ b/drivers/pci/controller/dwc/pcie-qcom.c -@@ -92,6 +92,7 @@ struct qcom_pcie_resources_2_1_0 { - struct reset_control *ahb_reset; - struct reset_control *por_reset; - struct reset_control *phy_reset; -+ struct reset_control *ext_reset; - struct regulator_bulk_data supplies[QCOM_PCIE_2_1_0_MAX_SUPPLY]; - }; - -@@ -261,6 +262,10 @@ static int qcom_pcie_get_resources_2_1_0 - if (IS_ERR(res->por_reset)) - return PTR_ERR(res->por_reset); - -+ res->ext_reset = devm_reset_control_get(dev, "ext"); -+ if (IS_ERR(res->ext_reset)) -+ return PTR_ERR(res->ext_reset); -+ - res->phy_reset = devm_reset_control_get_exclusive(dev, "phy"); - return PTR_ERR_OR_ZERO(res->phy_reset); - } -@@ -274,6 +279,7 @@ static void qcom_pcie_deinit_2_1_0(struc - reset_control_assert(res->ahb_reset); - reset_control_assert(res->por_reset); - reset_control_assert(res->pci_reset); -+ reset_control_assert(res->ext_reset); - clk_disable_unprepare(res->iface_clk); - clk_disable_unprepare(res->core_clk); - clk_disable_unprepare(res->phy_clk); -@@ -290,15 +296,21 @@ static int qcom_pcie_init_2_1_0(struct q - u32 val; - int ret; - -+ ret = reset_control_assert(res->ahb_reset); -+ if (ret) { -+ dev_err(dev, "cannot assert ahb reset\n"); -+ return ret; -+ } -+ - ret = regulator_bulk_enable(ARRAY_SIZE(res->supplies), res->supplies); - if (ret < 0) { - dev_err(dev, "cannot enable regulators\n"); - return ret; - } - -- ret = reset_control_assert(res->ahb_reset); -+ ret = reset_control_deassert(res->ext_reset); - if (ret) { -- dev_err(dev, "cannot assert ahb reset\n"); -+ dev_err(dev, "cannot assert ext reset\n"); - goto err_assert_ahb; - } - diff --git a/target/linux/ipq806x/patches-4.19/0071-3-PCI-qcom-Fixed-IPQ806x-PCIE-init-changes.patch b/target/linux/ipq806x/patches-4.19/0071-3-PCI-qcom-Fixed-IPQ806x-PCIE-init-changes.patch deleted file mode 100644 index dde8fbaa7b..0000000000 --- a/target/linux/ipq806x/patches-4.19/0071-3-PCI-qcom-Fixed-IPQ806x-PCIE-init-changes.patch +++ /dev/null @@ -1,124 +0,0 @@ -From eddd13215d0f2b549ebc5f0e8796d5b1231f90a0 Mon Sep 17 00:00:00 2001 -From: Sham Muthayyan -Date: Tue, 19 Jul 2016 19:58:22 +0530 -Subject: PCI: qcom: Fixed IPQ806x PCIE init changes - -Change-Id: Ic319b1aec27a47809284759f8fcb6a8815b7cf7e -Signed-off-by: Sham Muthayyan ---- - ---- a/drivers/pci/controller/dwc/pcie-qcom.c -+++ b/drivers/pci/controller/dwc/pcie-qcom.c -@@ -45,7 +45,13 @@ - #define PCIE_CAP_CPL_TIMEOUT_DISABLE 0x10 - - #define PCIE20_PARF_PHY_CTRL 0x40 -+#define PHY_CTRL_PHY_TX0_TERM_OFFSET_MASK (0x1f << 16) -+#define PHY_CTRL_PHY_TX0_TERM_OFFSET(x) (x << 16) -+ - #define PCIE20_PARF_PHY_REFCLK 0x4C -+#define REF_SSP_EN BIT(16) -+#define REF_USE_PAD BIT(12) -+ - #define PCIE20_PARF_DBI_BASE_ADDR 0x168 - #define PCIE20_PARF_SLV_ADDR_SPACE_SIZE 0x16C - #define PCIE20_PARF_MHI_CLOCK_RESET_CTRL 0x174 -@@ -76,6 +82,18 @@ - #define DBI_RO_WR_EN 1 - - #define PERST_DELAY_US 1000 -+/* PARF registers */ -+#define PCIE20_PARF_PCS_DEEMPH 0x34 -+#define PCS_DEEMPH_TX_DEEMPH_GEN1(x) (x << 16) -+#define PCS_DEEMPH_TX_DEEMPH_GEN2_3_5DB(x) (x << 8) -+#define PCS_DEEMPH_TX_DEEMPH_GEN2_6DB(x) (x << 0) -+ -+#define PCIE20_PARF_PCS_SWING 0x38 -+#define PCS_SWING_TX_SWING_FULL(x) (x << 8) -+#define PCS_SWING_TX_SWING_LOW(x) (x << 0) -+ -+#define PCIE20_PARF_CONFIG_BITS 0x50 -+#define PHY_RX0_EQ(x) (x << 24) - - #define PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE 0x358 - #define SLV_ADDR_SPACE_SZ 0x10000000 -@@ -94,6 +112,7 @@ struct qcom_pcie_resources_2_1_0 { - struct reset_control *phy_reset; - struct reset_control *ext_reset; - struct regulator_bulk_data supplies[QCOM_PCIE_2_1_0_MAX_SUPPLY]; -+ uint8_t phy_tx0_term_offset; - }; - - struct qcom_pcie_resources_1_0_0 { -@@ -173,6 +192,16 @@ struct qcom_pcie { - - #define to_qcom_pcie(x) dev_get_drvdata((x)->dev) - -+static inline void -+writel_masked(void __iomem *addr, u32 clear_mask, u32 set_mask) -+{ -+ u32 val = readl(addr); -+ -+ val &= ~clear_mask; -+ val |= set_mask; -+ writel(val, addr); -+} -+ - static void qcom_ep_reset_assert(struct qcom_pcie *pcie) - { - gpiod_set_value_cansleep(pcie->reset, 1); -@@ -266,6 +295,10 @@ static int qcom_pcie_get_resources_2_1_0 - if (IS_ERR(res->ext_reset)) - return PTR_ERR(res->ext_reset); - -+ if (of_property_read_u8(dev->of_node, "phy-tx0-term-offset", -+ &res->phy_tx0_term_offset)) -+ res->phy_tx0_term_offset = 0; -+ - res->phy_reset = devm_reset_control_get_exclusive(dev, "phy"); - return PTR_ERR_OR_ZERO(res->phy_reset); - } -@@ -293,7 +326,6 @@ static int qcom_pcie_init_2_1_0(struct q - struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0; - struct dw_pcie *pci = pcie->pci; - struct device *dev = pci->dev; -- u32 val; - int ret; - - ret = reset_control_assert(res->ahb_reset); -@@ -350,15 +382,26 @@ static int qcom_pcie_init_2_1_0(struct q - goto err_deassert_ahb; - } - -- /* enable PCIe clocks and resets */ -- val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL); -- val &= ~BIT(0); -- writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL); -- -- /* enable external reference clock */ -- val = readl(pcie->parf + PCIE20_PARF_PHY_REFCLK); -- val |= BIT(16); -- writel(val, pcie->parf + PCIE20_PARF_PHY_REFCLK); -+ writel_masked(pcie->parf + PCIE20_PARF_PHY_CTRL, BIT(0), 0); -+ -+ /* Set Tx termination offset */ -+ writel_masked(pcie->parf + PCIE20_PARF_PHY_CTRL, -+ PHY_CTRL_PHY_TX0_TERM_OFFSET_MASK, -+ PHY_CTRL_PHY_TX0_TERM_OFFSET(res->phy_tx0_term_offset)); -+ -+ /* PARF programming */ -+ writel(PCS_DEEMPH_TX_DEEMPH_GEN1(0x18) | -+ PCS_DEEMPH_TX_DEEMPH_GEN2_3_5DB(0x18) | -+ PCS_DEEMPH_TX_DEEMPH_GEN2_6DB(0x22), -+ pcie->parf + PCIE20_PARF_PCS_DEEMPH); -+ writel(PCS_SWING_TX_SWING_FULL(0x78) | -+ PCS_SWING_TX_SWING_LOW(0x78), -+ pcie->parf + PCIE20_PARF_PCS_SWING); -+ writel(PHY_RX0_EQ(0x4), pcie->parf + PCIE20_PARF_CONFIG_BITS); -+ -+ /* Enable reference clock */ -+ writel_masked(pcie->parf + PCIE20_PARF_PHY_REFCLK, -+ REF_USE_PAD, REF_SSP_EN); - - ret = reset_control_deassert(res->phy_reset); - if (ret) { diff --git a/target/linux/ipq806x/patches-4.19/0071-5-PCI-qcom-Programming-the-PCIE-iATU-for-IPQ806x.patch b/target/linux/ipq806x/patches-4.19/0071-5-PCI-qcom-Programming-the-PCIE-iATU-for-IPQ806x.patch deleted file mode 100644 index f6ebe0c0af..0000000000 --- a/target/linux/ipq806x/patches-4.19/0071-5-PCI-qcom-Programming-the-PCIE-iATU-for-IPQ806x.patch +++ /dev/null @@ -1,112 +0,0 @@ -From d27c303e828d7e42f339a459d2abfe30c51698e9 Mon Sep 17 00:00:00 2001 -From: Sham Muthayyan -Date: Tue, 26 Jul 2016 12:28:31 +0530 -Subject: PCI: qcom: Programming the PCIE iATU for IPQ806x - -Resolved PCIE EP detection errors caused due to missing iATU programming. - -Change-Id: Ie95c0f8cb940abc0192a8a3c4e825ddba54b72fe -Signed-off-by: Sham Muthayyan ---- - ---- a/drivers/pci/controller/dwc/pcie-qcom.c -+++ b/drivers/pci/controller/dwc/pcie-qcom.c -@@ -76,6 +76,30 @@ - #define PCIE20_CAP_LINK_1 (PCIE20_CAP + 0x14) - #define PCIE_CAP_LINK1_VAL 0x2FD7F - -+#define PCIE20_CAP_LINKCTRLSTATUS (PCIE20_CAP + 0x10) -+ -+#define PCIE20_AXI_MSTR_RESP_COMP_CTRL0 0x818 -+#define PCIE20_AXI_MSTR_RESP_COMP_CTRL1 0x81c -+ -+#define PCIE20_PLR_IATU_VIEWPORT 0x900 -+#define PCIE20_PLR_IATU_REGION_OUTBOUND (0x0 << 31) -+#define PCIE20_PLR_IATU_REGION_INDEX(x) (x << 0) -+ -+#define PCIE20_PLR_IATU_CTRL1 0x904 -+#define PCIE20_PLR_IATU_TYPE_CFG0 (0x4 << 0) -+#define PCIE20_PLR_IATU_TYPE_MEM (0x0 << 0) -+ -+#define PCIE20_PLR_IATU_CTRL2 0x908 -+#define PCIE20_PLR_IATU_ENABLE BIT(31) -+ -+#define PCIE20_PLR_IATU_LBAR 0x90C -+#define PCIE20_PLR_IATU_UBAR 0x910 -+#define PCIE20_PLR_IATU_LAR 0x914 -+#define PCIE20_PLR_IATU_LTAR 0x918 -+#define PCIE20_PLR_IATU_UTAR 0x91c -+ -+#define MSM_PCIE_DEV_CFG_ADDR 0x01000000 -+ - #define PCIE20_PARF_Q2A_FLUSH 0x1AC - - #define PCIE20_MISC_CONTROL_1_REG 0x8BC -@@ -240,6 +264,57 @@ static void qcom_pcie_2_1_0_ltssm_enable - writel(val, pcie->elbi + PCIE20_ELBI_SYS_CTRL); - } - -+static void qcom_pcie_prog_viewport_cfg0(struct qcom_pcie *pcie, u32 busdev) -+{ -+ struct pcie_port *pp = &pcie->pci->pp; -+ -+ /* -+ * program and enable address translation region 0 (device config -+ * address space); region type config; -+ * axi config address range to device config address range -+ */ -+ writel(PCIE20_PLR_IATU_REGION_OUTBOUND | -+ PCIE20_PLR_IATU_REGION_INDEX(0), -+ pcie->pci->dbi_base + PCIE20_PLR_IATU_VIEWPORT); -+ -+ writel(PCIE20_PLR_IATU_TYPE_CFG0, pcie->pci->dbi_base + PCIE20_PLR_IATU_CTRL1); -+ writel(PCIE20_PLR_IATU_ENABLE, pcie->pci->dbi_base + PCIE20_PLR_IATU_CTRL2); -+ writel(pp->cfg0_base, pcie->pci->dbi_base + PCIE20_PLR_IATU_LBAR); -+ writel((pp->cfg0_base >> 32), pcie->pci->dbi_base + PCIE20_PLR_IATU_UBAR); -+ writel((pp->cfg0_base + pp->cfg0_size - 1), -+ pcie->pci->dbi_base + PCIE20_PLR_IATU_LAR); -+ writel(busdev, pcie->pci->dbi_base + PCIE20_PLR_IATU_LTAR); -+ writel(0, pcie->pci->dbi_base + PCIE20_PLR_IATU_UTAR); -+} -+ -+static void qcom_pcie_prog_viewport_mem2_outbound(struct qcom_pcie *pcie) -+{ -+ struct pcie_port *pp = &pcie->pci->pp; -+ -+ /* -+ * program and enable address translation region 2 (device resource -+ * address space); region type memory; -+ * axi device bar address range to device bar address range -+ */ -+ writel(PCIE20_PLR_IATU_REGION_OUTBOUND | -+ PCIE20_PLR_IATU_REGION_INDEX(2), -+ pcie->pci->dbi_base + PCIE20_PLR_IATU_VIEWPORT); -+ -+ writel(PCIE20_PLR_IATU_TYPE_MEM, pcie->pci->dbi_base + PCIE20_PLR_IATU_CTRL1); -+ writel(PCIE20_PLR_IATU_ENABLE, pcie->pci->dbi_base + PCIE20_PLR_IATU_CTRL2); -+ writel(pp->mem_base, pcie->pci->dbi_base + PCIE20_PLR_IATU_LBAR); -+ writel((pp->mem_base >> 32), pcie->pci->dbi_base + PCIE20_PLR_IATU_UBAR); -+ writel(pp->mem_base + pp->mem_size - 1, -+ pcie->pci->dbi_base + PCIE20_PLR_IATU_LAR); -+ writel(pp->mem_bus_addr, pcie->pci->dbi_base + PCIE20_PLR_IATU_LTAR); -+ writel(upper_32_bits(pp->mem_bus_addr), -+ pcie->pci->dbi_base + PCIE20_PLR_IATU_UTAR); -+ -+ /* 256B PCIE buffer setting */ -+ writel(0x1, pcie->pci->dbi_base + PCIE20_AXI_MSTR_RESP_COMP_CTRL0); -+ writel(0x1, pcie->pci->dbi_base + PCIE20_AXI_MSTR_RESP_COMP_CTRL1); -+} -+ - static int qcom_pcie_get_resources_2_1_0(struct qcom_pcie *pcie) - { - struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0; -@@ -437,6 +512,9 @@ static int qcom_pcie_init_2_1_0(struct q - writel(CFG_BRIDGE_SB_INIT, - pci->dbi_base + PCIE20_AXI_MSTR_RESP_COMP_CTRL1); - -+ qcom_pcie_prog_viewport_cfg0(pcie, MSM_PCIE_DEV_CFG_ADDR); -+ qcom_pcie_prog_viewport_mem2_outbound(pcie); -+ - return 0; - - err_deassert_ahb: diff --git a/target/linux/ipq806x/patches-4.19/0071-6-PCI-qcom-Force-GEN1-support.patch b/target/linux/ipq806x/patches-4.19/0071-6-PCI-qcom-Force-GEN1-support.patch deleted file mode 100644 index c1461e68c2..0000000000 --- a/target/linux/ipq806x/patches-4.19/0071-6-PCI-qcom-Force-GEN1-support.patch +++ /dev/null @@ -1,59 +0,0 @@ -From 4910cfd150342ec7b038892262923c725a9c4001 Mon Sep 17 00:00:00 2001 -From: Sham Muthayyan -Date: Wed, 7 Sep 2016 16:44:28 +0530 -Subject: PCI: qcom: Force GEN1 support - -Change-Id: Ica54ddb737d7b851469deab1745f54bf431bd3f0 -Signed-off-by: Sham Muthayyan ---- - ---- a/drivers/pci/controller/dwc/pcie-qcom.c -+++ b/drivers/pci/controller/dwc/pcie-qcom.c -@@ -122,6 +122,8 @@ - #define PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE 0x358 - #define SLV_ADDR_SPACE_SZ 0x10000000 - -+#define PCIE20_LNK_CONTROL2_LINK_STATUS2 0xA0 -+ - #define QCOM_PCIE_2_1_0_MAX_SUPPLY 3 - struct qcom_pcie_resources_2_1_0 { - struct clk *iface_clk; -@@ -212,6 +214,7 @@ struct qcom_pcie { - struct phy *phy; - struct gpio_desc *reset; - const struct qcom_pcie_ops *ops; -+ uint32_t force_gen1; - }; - - #define to_qcom_pcie(x) dev_get_drvdata((x)->dev) -@@ -504,6 +507,11 @@ static int qcom_pcie_init_2_1_0(struct q - - /* wait for clock acquisition */ - usleep_range(1000, 1500); -+ if (pcie->force_gen1) { -+ writel_relaxed((readl_relaxed( -+ pcie->pci->dbi_base + PCIE20_LNK_CONTROL2_LINK_STATUS2) | 1), -+ pcie->pci->dbi_base + PCIE20_LNK_CONTROL2_LINK_STATUS2); -+ } - - - /* Set the Max TLP size to 2K, instead of using default of 4K */ -@@ -1367,6 +1375,8 @@ static int qcom_pcie_probe(struct platfo - struct dw_pcie *pci; - struct qcom_pcie *pcie; - int ret; -+ uint32_t force_gen1 = 0; -+ struct device_node *np = pdev->dev.of_node; - - pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL); - if (!pcie) -@@ -1397,6 +1407,9 @@ static int qcom_pcie_probe(struct platfo - goto err_pm_runtime_put; - } - -+ of_property_read_u32(np, "force_gen1", &force_gen1); -+ pcie->force_gen1 = force_gen1; -+ - res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "parf"); - pcie->parf = devm_ioremap_resource(dev, res); - if (IS_ERR(pcie->parf)) { diff --git a/target/linux/ipq806x/patches-4.19/0071-7-pcie-Set-PCIE-MRRS-and-MPS-to-256B.patch b/target/linux/ipq806x/patches-4.19/0071-7-pcie-Set-PCIE-MRRS-and-MPS-to-256B.patch deleted file mode 100644 index e7b5b6f9af..0000000000 --- a/target/linux/ipq806x/patches-4.19/0071-7-pcie-Set-PCIE-MRRS-and-MPS-to-256B.patch +++ /dev/null @@ -1,69 +0,0 @@ -From edff8f777c6321ca89bb950a382f409c4a126e28 Mon Sep 17 00:00:00 2001 -From: Gokul Sriram Palanisamy -Date: Thu, 15 Dec 2016 17:38:18 +0530 -Subject: pcie: Set PCIE MRRS and MPS to 256B - -Set Max Read Request Size and Max Payload Size to 256 bytes, -per chip team recommendation. - -Change-Id: I097004be2ced1b3096ffc10c318aae0b2bb155e8 -Signed-off-by: Gokul Sriram Palanisamy ---- - drivers/pci/host/pcie-qcom.c | 37 +++++++++++++++++++++++++++++++++++++ - 1 file changed, 37 insertions(+) - -(limited to 'drivers/pci/host/pcie-qcom.c') - ---- a/drivers/pci/controller/dwc/pcie-qcom.c -+++ b/drivers/pci/controller/dwc/pcie-qcom.c -@@ -124,6 +124,14 @@ - - #define PCIE20_LNK_CONTROL2_LINK_STATUS2 0xA0 - -+#define __set(v, a, b) (((v) << (b)) & GENMASK(a, b)) -+#define __mask(a, b) (((1 << ((a) + 1)) - 1) & ~((1 << (b)) - 1)) -+#define PCIE20_DEV_CAS 0x78 -+#define PCIE20_MRRS_MASK __mask(14, 12) -+#define PCIE20_MRRS(x) __set(x, 14, 12) -+#define PCIE20_MPS_MASK __mask(7, 5) -+#define PCIE20_MPS(x) __set(x, 7, 5) -+ - #define QCOM_PCIE_2_1_0_MAX_SUPPLY 3 - struct qcom_pcie_resources_2_1_0 { - struct clk *iface_clk; -@@ -1475,6 +1483,35 @@ err_pm_runtime_put: - return ret; - } - -+static void qcom_pcie_fixup_final(struct pci_dev *dev) -+{ -+ int cap, err; -+ u16 ctl, reg_val; -+ -+ cap = pci_pcie_cap(dev); -+ if (!cap) -+ return; -+ -+ err = pci_read_config_word(dev, cap + PCI_EXP_DEVCTL, &ctl); -+ -+ if (err) -+ return; -+ -+ reg_val = ctl; -+ -+ if (((reg_val & PCIE20_MRRS_MASK) >> 12) > 1) -+ reg_val = (reg_val & ~(PCIE20_MRRS_MASK)) | PCIE20_MRRS(0x1); -+ -+ if (((ctl & PCIE20_MPS_MASK) >> 5) > 1) -+ reg_val = (reg_val & ~(PCIE20_MPS_MASK)) | PCIE20_MPS(0x1); -+ -+ err = pci_write_config_word(dev, cap + PCI_EXP_DEVCTL, reg_val); -+ -+ if (err) -+ pr_err("pcie config write failed %d\n", err); -+} -+DECLARE_PCI_FIXUP_FINAL(PCI_ANY_ID, PCI_ANY_ID, qcom_pcie_fixup_final); -+ - static const struct of_device_id qcom_pcie_match[] = { - { .compatible = "qcom,pcie-apq8084", .data = &ops_1_0_0 }, - { .compatible = "qcom,pcie-ipq8064", .data = &ops_2_1_0 }, diff --git a/target/linux/ipq806x/patches-4.19/0071-8-pcie-qcom-Fixed-pcie_phy_clk-branch-issue.patch b/target/linux/ipq806x/patches-4.19/0071-8-pcie-qcom-Fixed-pcie_phy_clk-branch-issue.patch deleted file mode 100644 index 7cbeb3bed7..0000000000 --- a/target/linux/ipq806x/patches-4.19/0071-8-pcie-qcom-Fixed-pcie_phy_clk-branch-issue.patch +++ /dev/null @@ -1,91 +0,0 @@ -From b74bab6186131eea09459eedf5d737645a3559c9 Mon Sep 17 00:00:00 2001 -From: Abhishek Sahu -Date: Thu, 22 Dec 2016 11:18:45 +0530 -Subject: pcie: qcom: Fixed pcie_phy_clk branch issue - -Following backtraces are observed in PCIe deinit operation. - - Hardware name: Qualcomm (Flattened Device Tree) - (unwind_backtrace) from [] (show_stack+0x10/0x14) - (show_stack) from [] (dump_stack+0x84/0x98) - (dump_stack) from [] (warn_slowpath_common+0x9c/0xb8) - (warn_slowpath_common) from [] (warn_slowpath_fmt+0x30/0x40) - (warn_slowpath_fmt) from [] (clk_branch_wait+0x114/0x120) - (clk_branch_wait) from [] (clk_core_disable+0xd0/0x1f4) - (clk_core_disable) from [] (clk_disable+0x24/0x30) - (clk_disable) from [] (qcom_pcie_deinit_v0+0x6c/0xb8) - (qcom_pcie_deinit_v0) from [] (qcom_pcie_host_init+0xe0/0xe8) - (qcom_pcie_host_init) from [] (dw_pcie_host_init+0x3b0/0x538) - (dw_pcie_host_init) from [] (qcom_pcie_probe+0x20c/0x2e4) - -pcie_phy_clk is generated for PCIe controller itself and the -GCC controls its branch operation. This error is coming since -the assert operations turn off the parent clock before branch -clock. Now this patch moves clk_disable_unprepare before assert -operations. - -Similarly, during probe function, the clock branch operation -should be done after dessert operation. Currently, it does not -generate any error since bootloader enables the pcie_phy_clk -but the same error is coming during probe, if bootloader -disables pcie_phy_clk. - -Change-Id: Ib29c154d10eb64363d9cc982ce5fd8107af5627d -Signed-off-by: Abhishek Sahu ---- - drivers/pci/host/pcie-qcom.c | 16 +++++++--------- - 1 file changed, 7 insertions(+), 9 deletions(-) - ---- a/drivers/pci/controller/dwc/pcie-qcom.c -+++ b/drivers/pci/controller/dwc/pcie-qcom.c -@@ -393,6 +393,7 @@ static void qcom_pcie_deinit_2_1_0(struc - { - struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0; - -+ clk_disable_unprepare(res->phy_clk); - reset_control_assert(res->pci_reset); - reset_control_assert(res->axi_reset); - reset_control_assert(res->ahb_reset); -@@ -401,7 +402,6 @@ static void qcom_pcie_deinit_2_1_0(struc - reset_control_assert(res->ext_reset); - clk_disable_unprepare(res->iface_clk); - clk_disable_unprepare(res->core_clk); -- clk_disable_unprepare(res->phy_clk); - clk_disable_unprepare(res->aux_clk); - clk_disable_unprepare(res->ref_clk); - regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies); -@@ -444,12 +444,6 @@ static int qcom_pcie_init_2_1_0(struct q - goto err_clk_core; - } - -- ret = clk_prepare_enable(res->phy_clk); -- if (ret) { -- dev_err(dev, "cannot prepare/enable phy clock\n"); -- goto err_clk_phy; -- } -- - ret = clk_prepare_enable(res->aux_clk); - if (ret) { - dev_err(dev, "cannot prepare/enable aux clock\n"); -@@ -513,6 +507,12 @@ static int qcom_pcie_init_2_1_0(struct q - return ret; - } - -+ ret = clk_prepare_enable(res->phy_clk); -+ if (ret) { -+ dev_err(dev, "cannot prepare/enable phy clock\n"); -+ goto err_deassert_ahb; -+ } -+ - /* wait for clock acquisition */ - usleep_range(1000, 1500); - if (pcie->force_gen1) { -@@ -538,8 +538,6 @@ err_deassert_ahb: - err_clk_ref: - clk_disable_unprepare(res->aux_clk); - err_clk_aux: -- clk_disable_unprepare(res->phy_clk); --err_clk_phy: - clk_disable_unprepare(res->core_clk); - err_clk_core: - clk_disable_unprepare(res->iface_clk); diff --git a/target/linux/ipq806x/patches-4.19/0071-9-pcie-qcom-change-duplicate-pci-reset-to-phy-reset.patch b/target/linux/ipq806x/patches-4.19/0071-9-pcie-qcom-change-duplicate-pci-reset-to-phy-reset.patch deleted file mode 100644 index 3fff78bfd4..0000000000 --- a/target/linux/ipq806x/patches-4.19/0071-9-pcie-qcom-change-duplicate-pci-reset-to-phy-reset.patch +++ /dev/null @@ -1,25 +0,0 @@ -From 1a9c48123bd09f75562b6a2ee0f0a7b2d533cd45 Mon Sep 17 00:00:00 2001 -From: Abhishek Sahu -Date: Thu, 22 Dec 2016 11:50:49 +0530 -Subject: pcie: qcom: change duplicate pci reset to phy reset - -The deinit issues reset_control_assert for pci twice and -does not contain phy reset. - -Change-Id: Iba849963c7e5f9a2a1063f0e2e89635df70b8a99 -Signed-off-by: Abhishek Sahu ---- - drivers/pci/host/pcie-qcom.c | 2 +- - 1 file changed, 1 insertion(+), 1 deletion(-) - ---- a/drivers/pci/controller/dwc/pcie-qcom.c -+++ b/drivers/pci/controller/dwc/pcie-qcom.c -@@ -394,7 +394,7 @@ static void qcom_pcie_deinit_2_1_0(struc - struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0; - - clk_disable_unprepare(res->phy_clk); -- reset_control_assert(res->pci_reset); -+ reset_control_assert(res->phy_reset); - reset_control_assert(res->axi_reset); - reset_control_assert(res->ahb_reset); - reset_control_assert(res->por_reset); diff --git a/target/linux/ipq806x/patches-4.19/0072-add-ipq806x-with-no-clocks.patch b/target/linux/ipq806x/patches-4.19/0072-add-ipq806x-with-no-clocks.patch deleted file mode 100644 index ecd9672d1b..0000000000 --- a/target/linux/ipq806x/patches-4.19/0072-add-ipq806x-with-no-clocks.patch +++ /dev/null @@ -1,12 +0,0 @@ ---- a/drivers/firmware/qcom_scm.c -+++ b/drivers/firmware/qcom_scm.c -@@ -606,6 +606,9 @@ static const struct of_device_id qcom_sc - { .compatible = "qcom,scm-ipq4019", - .data = NULL, /* no clocks */ - }, -+ { .compatible = "qcom,scm-ipq806x", -+ .data = NULL, /* no clocks */ -+ }, - { .compatible = "qcom,scm", - .data = (void *)(SCM_HAS_CORE_CLK - | SCM_HAS_IFACE_CLK diff --git a/target/linux/ipq806x/patches-4.19/0073-pinctrl-qom-use-scm_call-to-route-GPIO-irq-to-Apps.patch b/target/linux/ipq806x/patches-4.19/0073-pinctrl-qom-use-scm_call-to-route-GPIO-irq-to-Apps.patch deleted file mode 100644 index 78a5bb4173..0000000000 --- a/target/linux/ipq806x/patches-4.19/0073-pinctrl-qom-use-scm_call-to-route-GPIO-irq-to-Apps.patch +++ /dev/null @@ -1,71 +0,0 @@ -From 2034addc7e193dc81d7ca60d8884832751b76758 Mon Sep 17 00:00:00 2001 -From: Ajay Kishore -Date: Tue, 24 Jan 2017 14:14:16 +0530 -Subject: pinctrl: qcom: use scm_call to route GPIO irq to Apps - -For IPQ806x targets, TZ protects the registers that are used to -configure the routing of interrupts to a target processor. -To resolve this, this patch uses scm call to route GPIO interrupts -to application processor. Also the scm call interface is changed. - -Change-Id: Ib6c06829d04bc8c20483c36e63da92e26cdef9ce -Signed-off-by: Ajay Kishore ---- - ---- a/drivers/pinctrl/qcom/pinctrl-msm.c -+++ b/drivers/pinctrl/qcom/pinctrl-msm.c -@@ -30,7 +30,8 @@ - #include - #include - #include -- -+#include -+#include - #include "../core.h" - #include "../pinconf.h" - #include "pinctrl-msm.h" -@@ -628,6 +629,9 @@ static void msm_gpio_irq_mask(struct irq - const struct msm_pingroup *g; - unsigned long flags; - u32 val; -+ u32 addr; -+ int ret; -+ const __be32 *reg; - - g = &pctrl->soc->groups[d->hwirq]; - -@@ -732,11 +736,30 @@ static int msm_gpio_irq_set_type(struct - else - clear_bit(d->hwirq, pctrl->dual_edge_irqs); - -+ int ret = of_device_is_compatible(pctrl->dev->of_node, -+ "qcom,ipq8064-pinctrl"); - /* Route interrupts to application cpu */ -- val = readl(pctrl->regs + g->intr_target_reg); -- val &= ~(7 << g->intr_target_bit); -- val |= g->intr_target_kpss_val << g->intr_target_bit; -- writel(val, pctrl->regs + g->intr_target_reg); -+ if (!ret) { -+ val = readl(pctrl->regs + g->intr_target_reg); -+ val &= ~(7 << g->intr_target_bit); -+ val |= g->intr_target_kpss_val << g->intr_target_bit; -+ writel(val, pctrl->regs + g->intr_target_reg); -+ } else { -+ const __be32 *reg = of_get_property(pctrl->dev->of_node, "reg", NULL); -+ if (reg) { -+ u32 addr = be32_to_cpup(reg) + g->intr_target_reg; -+ qcom_scm_io_readl(addr, &val); -+ __iormb(); -+ -+ val &= ~(7 << g->intr_target_bit); -+ val |= g->intr_target_kpss_val << g->intr_target_bit; -+ -+ __iowmb(); -+ ret = qcom_scm_io_writel(addr, val); -+ if (ret) -+ pr_err("\n Routing interrupts to Apps proc failed"); -+ } -+ } - - /* Update configuration for gpio. - * RAW_STATUS_EN is left on for all gpio irqs. Due to the diff --git a/target/linux/ipq806x/patches-4.19/0075-ipq8064-pinctrl-Fixed-missing-RGMII-pincontrol-defin.patch b/target/linux/ipq806x/patches-4.19/0075-ipq8064-pinctrl-Fixed-missing-RGMII-pincontrol-defin.patch deleted file mode 100644 index 2867239d1c..0000000000 --- a/target/linux/ipq806x/patches-4.19/0075-ipq8064-pinctrl-Fixed-missing-RGMII-pincontrol-defin.patch +++ /dev/null @@ -1,50 +0,0 @@ -From a3488aa9bed37c56e405967d44e821c484b5d6b9 Mon Sep 17 00:00:00 2001 -From: Ram Chandra Jangir -Date: Fri, 28 Sep 2018 15:19:50 +0530 -Subject: [PATCH] ipq8064: pinctrl: Fixed missing RGMII pincontrol definitions - -Signed-off-by: Ram Chandra Jangir ---- - drivers/pinctrl/qcom/pinctrl-ipq8064.c | 10 +++++----- - 1 file changed, 5 insertions(+), 5 deletions(-) - ---- a/drivers/pinctrl/qcom/pinctrl-ipq8064.c -+++ b/drivers/pinctrl/qcom/pinctrl-ipq8064.c -@@ -308,7 +308,7 @@ static const char * const gpio_groups[] - }; - - static const char * const mdio_groups[] = { -- "gpio0", "gpio1", "gpio10", "gpio11", -+ "gpio0", "gpio1", "gpio2", "gpio10", "gpio11", "gpio66", - }; - - static const char * const mi2s_groups[] = { -@@ -412,8 +412,8 @@ static const char * const usb2_hsic_grou - }; - - static const char * const rgmii2_groups[] = { -- "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", -- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62", -+ "gpio2", "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", -+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62", "gpio66", - }; - - static const char * const sata_groups[] = { -@@ -548,7 +548,7 @@ static const struct msm_function ipq8064 - static const struct msm_pingroup ipq8064_groups[] = { - PINGROUP(0, mdio, NA, NA, NA, NA, NA, NA, NA, NA, NA), - PINGROUP(1, mdio, NA, NA, NA, NA, NA, NA, NA, NA, NA), -- PINGROUP(2, gsbi5_spi_cs3, NA, NA, NA, NA, NA, NA, NA, NA, NA), -+ PINGROUP(2, gsbi5_spi_cs3, rgmii2, mdio, NA, NA, NA, NA, NA, NA, NA), - PINGROUP(3, pcie1_rst, pcie1_prsnt, pdm, NA, NA, NA, NA, NA, NA, NA), - PINGROUP(4, pcie1_pwren_n, pcie1_pwren, NA, NA, NA, NA, NA, NA, NA, NA), - PINGROUP(5, pcie1_clk_req, pcie1_pwrflt, NA, NA, NA, NA, NA, NA, NA, NA), -@@ -612,7 +612,7 @@ static const struct msm_pingroup ipq8064 - PINGROUP(63, pcie3_rst, NA, NA, NA, NA, NA, NA, NA, NA, NA), - PINGROUP(64, NA, NA, NA, NA, NA, NA, NA, NA, NA, NA), - PINGROUP(65, pcie3_clk_req, NA, NA, NA, NA, NA, NA, NA, NA, NA), -- PINGROUP(66, NA, NA, NA, NA, NA, NA, NA, NA, NA, NA), -+ PINGROUP(66, rgmii2, mdio, NA, NA, NA, NA, NA, NA, NA, NA), - PINGROUP(67, usb2_hsic, NA, NA, NA, NA, NA, NA, NA, NA, NA), - PINGROUP(68, usb2_hsic, NA, NA, NA, NA, NA, NA, NA, NA, NA), - SDC_PINGROUP(sdc3_clk, 0x204a, 14, 6), diff --git a/target/linux/ipq806x/patches-4.19/080-ARM-dts-qcom-add-gpio-ranges-property.patch b/target/linux/ipq806x/patches-4.19/080-ARM-dts-qcom-add-gpio-ranges-property.patch deleted file mode 100644 index 1ab070bdab..0000000000 --- a/target/linux/ipq806x/patches-4.19/080-ARM-dts-qcom-add-gpio-ranges-property.patch +++ /dev/null @@ -1,70 +0,0 @@ -From patchwork Mon May 21 20:57:38 2018 -Content-Type: text/plain; charset="utf-8" -MIME-Version: 1.0 -Content-Transfer-Encoding: 7bit -Subject: [v5,3/4] ARM: dts: qcom: add gpio-ranges property -X-Patchwork-Submitter: Christian Lamparter -X-Patchwork-Id: 917856 -Message-Id: <0ae3376606a89bcdf3fe753a5c967f7103699e09.1526935804.git.chunkeey@gmail.com> -To: linux-gpio@vger.kernel.org, linux-arm-kernel@lists.infradead.org, - linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org -Cc: Bjorn Andersson , - Linus Walleij , - Stephen Boyd , David Brown , - Rob Herring , Mark Rutland , - Andy Gross , - Sven Eckelmann -Date: Mon, 21 May 2018 22:57:38 +0200 -From: Christian Lamparter -List-Id: - -This patch adds the gpio-ranges property to almost all of -the Qualcomm ARM platforms that utilize the pinctrl-msm -framework. - -The gpio-ranges property is part of the gpiolib subsystem. -As a result, the binding text is available in section -"2.1 gpio- and pin-controller interaction" of -Documentation/devicetree/bindings/gpio/gpio.txt - -For more information please see the patch titled: -"pinctrl: msm: fix gpio-hog related boot issues" from -this series. - -Reported-by: Sven Eckelmann -Tested-by: Sven Eckelmann [ipq4019] -Reviewed-by: Bjorn Andersson -Signed-off-by: Christian Lamparter -Reviewed-by: Linus Walleij ---- -To help with git bisect, the DT update patch has been intentionally -placed after the "pinctrl: msm: fix gpio-hog related boot issues". -Otherwise - if the order was reveresed - and bisect decides to split -between these two patches, the gpiochip_add_pin_ranges() function -will be executed twice with the same parameters for the same pinctrl. ---- - arch/arm/boot/dts/qcom-apq8064.dtsi | 1 + - arch/arm/boot/dts/qcom-apq8084.dtsi | 1 + - arch/arm/boot/dts/qcom-ipq4019.dtsi | 1 + - arch/arm/boot/dts/qcom-ipq8064.dtsi | 1 + - arch/arm/boot/dts/qcom-mdm9615.dtsi | 1 + - arch/arm/boot/dts/qcom-msm8660.dtsi | 1 + - arch/arm/boot/dts/qcom-msm8960.dtsi | 1 + - arch/arm/boot/dts/qcom-msm8974.dtsi | 1 + - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 3 ++- - arch/arm64/boot/dts/qcom/msm8916.dtsi | 1 + - arch/arm64/boot/dts/qcom/msm8992.dtsi | 1 + - arch/arm64/boot/dts/qcom/msm8994.dtsi | 1 + - arch/arm64/boot/dts/qcom/msm8996.dtsi | 1 + - 13 files changed, 14 insertions(+), 1 deletion(-) - ---- a/arch/arm/boot/dts/qcom-ipq8064.dtsi -+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi -@@ -668,6 +668,7 @@ - reg = <0x800000 0x4000>; - - gpio-controller; -+ gpio-ranges = <&qcom_pinmux 0 0 69>; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; diff --git a/target/linux/ipq806x/patches-4.19/850-soc-add-qualcomm-syscon.patch b/target/linux/ipq806x/patches-4.19/850-soc-add-qualcomm-syscon.patch deleted file mode 100644 index 50414596d9..0000000000 --- a/target/linux/ipq806x/patches-4.19/850-soc-add-qualcomm-syscon.patch +++ /dev/null @@ -1,121 +0,0 @@ -From: Christian Lamparter -Subject: SoC: add qualcomm syscon ---- a/drivers/soc/qcom/Makefile -+++ b/drivers/soc/qcom/Makefile -@@ -18,6 +18,7 @@ obj-$(CONFIG_QCOM_SMEM_STATE) += smem_st - obj-$(CONFIG_QCOM_SMP2P) += smp2p.o - obj-$(CONFIG_QCOM_SMSM) += smsm.o - obj-$(CONFIG_QCOM_WCNSS_CTRL) += wcnss_ctrl.o -+obj-$(CONFIG_QCOM_TCSR) += qcom_tcsr.o - obj-$(CONFIG_QCOM_APR) += apr.o - obj-$(CONFIG_QCOM_LLCC) += llcc-slice.o - obj-$(CONFIG_QCOM_SDM845_LLCC) += llcc-sdm845.o ---- a/drivers/soc/qcom/Kconfig -+++ b/drivers/soc/qcom/Kconfig -@@ -146,6 +146,13 @@ config QCOM_SMSM - Say yes here to support the Qualcomm Shared Memory State Machine. - The state machine is represented by bits in shared memory. - -+config QCOM_TCSR -+ tristate "QCOM Top Control and Status Registers" -+ depends on ARCH_QCOM -+ help -+ Say y here to enable TCSR support. The TCSR provides control -+ functions for various peripherals. -+ - config QCOM_WCNSS_CTRL - tristate "Qualcomm WCNSS control driver" - depends on ARCH_QCOM ---- /dev/null -+++ b/drivers/soc/qcom/qcom_tcsr.c -@@ -0,0 +1,64 @@ -+/* -+ * Copyright (c) 2014, The Linux foundation. All rights reserved. -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License rev 2 and -+ * only rev 2 as published by the free Software foundation. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or fITNESS fOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ */ -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#define TCSR_USB_PORT_SEL 0xb0 -+ -+static int tcsr_probe(struct platform_device *pdev) -+{ -+ struct resource *res; -+ const struct device_node *node = pdev->dev.of_node; -+ void __iomem *base; -+ u32 val; -+ -+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); -+ base = devm_ioremap_resource(&pdev->dev, res); -+ if (IS_ERR(base)) -+ return PTR_ERR(base); -+ -+ if (!of_property_read_u32(node, "qcom,usb-ctrl-select", &val)) { -+ dev_err(&pdev->dev, "setting usb port select = %d\n", val); -+ writel(val, base + TCSR_USB_PORT_SEL); -+ } -+ -+ return 0; -+} -+ -+static const struct of_device_id tcsr_dt_match[] = { -+ { .compatible = "qcom,tcsr", }, -+ { }, -+}; -+ -+MODULE_DEVICE_TABLE(of, tcsr_dt_match); -+ -+static struct platform_driver tcsr_driver = { -+ .driver = { -+ .name = "tcsr", -+ .owner = THIS_MODULE, -+ .of_match_table = tcsr_dt_match, -+ }, -+ .probe = tcsr_probe, -+}; -+ -+module_platform_driver(tcsr_driver); -+ -+MODULE_AUTHOR("Andy Gross "); -+MODULE_DESCRIPTION("QCOM TCSR driver"); -+MODULE_LICENSE("GPL v2"); ---- /dev/null -+++ b/include/dt-bindings/soc/qcom,tcsr.h -@@ -0,0 +1,23 @@ -+/* Copyright (c) 2014, The Linux Foundation. All rights reserved. -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 and -+ * only version 2 as published by the Free Software Foundation. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ */ -+#ifndef __DT_BINDINGS_QCOM_TCSR_H -+#define __DT_BINDINGS_QCOM_TCSR_H -+ -+#define TCSR_USB_SELECT_USB3_P0 0x1 -+#define TCSR_USB_SELECT_USB3_P1 0x2 -+#define TCSR_USB_SELECT_USB3_DUAL 0x3 -+ -+/* TCSR A/B REG */ -+#define IPQ806X_TCSR_REG_A_ADM_CRCI_MUX_SEL 0 -+#define IPQ806X_TCSR_REG_B_ADM_CRCI_MUX_SEL 1 -+ -+#endif