From: INAGAKI Hiroshi Date: Wed, 8 Mar 2023 12:54:14 +0000 (+0900) Subject: mvebu: add support for Fortinet FortiWiFi 50E-2R X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=26a2135c6d2aad07b46ee82ecac4c54900adb151;p=openwrt%2Fstaging%2Fxback.git mvebu: add support for Fortinet FortiWiFi 50E-2R Fortinet FortiWiFi 50E-2R (FWF-50E-2R) is a UTM with 2x WLAN, based on Armada 385 (88F6820). Specification: - SoC : Marvell Armada 385 88F6820 - RAM : DDR3 2 GiB (4x Nanya NT5CC512M8EN-EK) - Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G) - Ethernet : 7x 10/100/1000 Mbps - LAN 1-5 : Marvell 88E6176 - WAN 1, 2 : Marvell 88E1512 (2x) - WLAN : Gemtek WMDQ-177ACN (Qualcomm Atheros QCA9892 (2T2R)) (2x) - interface : MiniPCIe - LEDs/Keys : 18x/1x - UART : "CONSOLE" port (RJ-45, RS-232C level) - port : ttyS0 - settings : 9600bps 8n1 - assignment : 1:NC , 2:NC , 3:TXD, 4:GND, 5:GND, 6:RXD, 7:NC , 8:NC - note : compatible with Cisco console cable - HW Monitoring: nuvoTon NCT7802Y - Power : 12 VDC, 2.5 A - plug : Molex 5557-02R Flash instruction using initramfs image: 1. Power on FWF-50E-2R and interrupt to show bootmenu 2. Call "[I]: System information." -> "[S]: Set serial port baudrate." and set baudrate to 9600 bps 3. Call "[R]: Review TFTP parameters.", check TFTP parameters and connect computer to "Image download port" in the parameters 4. Prepare TFTP server with the parameters obtained above 5. Rename OpenWrt initramfs image to "image.out" and put to TFTP directory 6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs image from TFTP server 7. Type "R" key when the following message is showed, to boot initramfs image without flashing to spi-nor flash "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?" 8. On initramfs image, backup mtd if needed minimum: - "firmware-info" - "kernel" - "rootfs" 9. On initramfs image, upload sysupgrade image to the device and perform sysupgrade 10. Wait ~200 seconds to complete flashing and rebooting. If the device is booted with stock firmware, login to bootmenu and call "[B]: Boot with backup firmware and set as default." to set the first OS image as default and boot it. Notes: - Both colors of Bi-color LEDs on the front panel cannot be turned on at the same time. - "PWR" and "Logo" LEDs are connected to power source directly. - The following partitions are added for OpenWrt. These partitions are contained in "uboot" partition (0x0-0x1fffff) on stock firmware. - "firmware-info" - "dtb" - "u-boot-env" - "board-info" Image header for bootmenu tftp: 0x0 - 0xf : ? 0x10 - 0x2f : Image Name 0x30 - 0x17f: ? 0x180 - 0x183: Kernel Offset* 0x184 - 0x187: Kernel Length* 0x188 - 0x18b: RootFS Offset (ext2)* 0x18c - 0x18f: RootFS Length (ext2)* 0x190 - 0x193: DTB Offset 0x194 - 0x197: DTB Length 0x198 - 0x19b: Data Offset (jffs2) 0x19c - 0x19f: Data Length (jffs2) 0x1a0 - 0x1ff: ? *: required for initramfs image MAC addresses: (eth0): 90:6C:AC:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex)) WAN 1 : 90:6C:AC:xx:xx:99 WAN 2 : 90:6C:AC:xx:xx:9A LAN 1 : 90:6C:AC:xx:xx:9B LAN 2 : 90:6C:AC:xx:xx:9C LAN 3 : 90:6C:AC:xx:xx:9D LAN 4 : 90:6C:AC:xx:xx:9E LAN 5 : 90:6C:AC:xx:xx:9F WLAN 1: 1C:49:7B:xx:xx:xx (MiniPCIe Card) WLAN 2: 1C:49:7B:xx:xx:xx (MiniPCIe Card) Signed-off-by: INAGAKI Hiroshi Tested-by: Raylynn Knight --- diff --git a/target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network b/target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network index b3dbce8542..890c149d30 100644 --- a/target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network +++ b/target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network @@ -30,7 +30,8 @@ mvebu_setup_interfaces() ;; fortinet,fg-50e|\ fortinet,fg-51e|\ - fortinet,fg-52e) + fortinet,fg-52e|\ + fortinet,fwf-50e-2r) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5" "eth1 eth2" ;; iij,sa-w2) diff --git a/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh b/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh index bc39ddcf50..639f08cef6 100755 --- a/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh +++ b/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh @@ -55,7 +55,8 @@ platform_do_upgrade() { fortinet,fg-30e|\ fortinet,fg-50e|\ fortinet,fg-51e|\ - fortinet,fg-52e) + fortinet,fg-52e|\ + fortinet,fwf-50e-2r) fortinet_do_upgrade "$1" ;; iij,sa-w2) diff --git a/target/linux/mvebu/files-6.6/arch/arm/boot/dts/marvell/armada-385-fortinet-fwf-50e-2r.dts b/target/linux/mvebu/files-6.6/arch/arm/boot/dts/marvell/armada-385-fortinet-fwf-50e-2r.dts new file mode 100644 index 0000000000..eee9e6d942 --- /dev/null +++ b/target/linux/mvebu/files-6.6/arch/arm/boot/dts/marvell/armada-385-fortinet-fwf-50e-2r.dts @@ -0,0 +1,20 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "armada-385-fortinet-fg-5xe.dtsi" + +/ { + model = "Fortinet FortiWiFi 50E-2R"; + compatible = "fortinet,fwf-50e-2r", "marvell,armada385", "marvell,armada380"; +}; + +&pciec { + status = "okay"; +}; + +&pcie1 { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; diff --git a/target/linux/mvebu/image/cortexa9.mk b/target/linux/mvebu/image/cortexa9.mk index 00f81dc4fc..5cefdb846a 100644 --- a/target/linux/mvebu/image/cortexa9.mk +++ b/target/linux/mvebu/image/cortexa9.mk @@ -160,6 +160,17 @@ define Device/fortinet_fg-52e endef TARGET_DEVICES += fortinet_fg-52e +define Device/fortinet_fwf-50e-2r + $(Device/fortinet) + DEVICE_MODEL := FortiWiFi 50E-2R + DEVICE_DTS := armada-385-fortinet-fwf-50e-2r + KERNEL_INITRAMFS := kernel-bin | append-dtb | fortigate-header | \ + gzip-filename FW502R + DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct \ + wpad-basic-mbedtls +endef +TARGET_DEVICES += fortinet_fwf-50e-2r + define Device/globalscale_mirabox $(Device/NAND-512K) DEVICE_VENDOR := Globalscale