From: Guenter Roeck Date: Mon, 20 Mar 2017 18:16:11 +0000 (-0700) Subject: usb: hub: Fix error loop seen after hub communication errors X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=245b2eecee2aac6fdc77dcafaa73c33f9644c3c7;p=openwrt%2Fstaging%2Fblogic.git usb: hub: Fix error loop seen after hub communication errors While stress testing a usb controller using a bind/unbind looop, the following error loop was observed. usb 7-1.2: new low-speed USB device number 3 using xhci-hcd usb 7-1.2: hub failed to enable device, error -108 usb 7-1-port2: cannot disable (err = -22) usb 7-1-port2: couldn't allocate usb_device usb 7-1-port2: cannot disable (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: activate --> -22 hub 7-1:1.0: hub_ext_port_status failed (err = -22) hub 7-1:1.0: hub_ext_port_status failed (err = -22) ** 57 printk messages dropped ** hub 7-1:1.0: activate --> -22 ** 82 printk messages dropped ** hub 7-1:1.0: hub_ext_port_status failed (err = -22) This continues forever. After adding tracebacks into the code, the call sequence leading to this is found to be as follows. [] hub_activate+0x368/0x7b8 [] hub_resume+0x2c/0x3c [] usb_resume_interface.isra.6+0x128/0x158 [] usb_suspend_both+0x1e8/0x288 [] usb_runtime_suspend+0x3c/0x98 [] __rpm_callback+0x48/0x7c [] rpm_callback+0xa8/0xd4 [] rpm_suspend+0x84/0x758 [] rpm_idle+0x2c8/0x498 [] __pm_runtime_idle+0x60/0xac [] usb_autopm_put_interface+0x6c/0x7c [] hub_event+0x10ac/0x12ac [] process_one_work+0x390/0x6b8 [] worker_thread+0x480/0x610 [] kthread+0x164/0x178 [] ret_from_fork+0x10/0x40 kick_hub_wq() is called from hub_activate() even after failures to communicate with the hub. This results in an endless sequence of hub event -> hub activate -> wq trigger -> hub event -> ... Provide two solutions for the problem. - Only trigger the hub event queue if communication with the hub is successful. - After a suspend failure, only resume already suspended interfaces if the communication with the device is still possible. Each of the changes fixes the observed problem. Use both to improve robustness. Acked-by: Alan Stern Signed-off-by: Guenter Roeck Cc: stable Signed-off-by: Greg Kroah-Hartman --- diff --git a/drivers/usb/core/driver.c b/drivers/usb/core/driver.c index cdee5130638b..7ebdf2a4e8fe 100644 --- a/drivers/usb/core/driver.c +++ b/drivers/usb/core/driver.c @@ -1331,6 +1331,24 @@ static int usb_suspend_both(struct usb_device *udev, pm_message_t msg) */ if (udev->parent && !PMSG_IS_AUTO(msg)) status = 0; + + /* + * If the device is inaccessible, don't try to resume + * suspended interfaces and just return the error. + */ + if (status && status != -EBUSY) { + int err; + u16 devstat; + + err = usb_get_status(udev, USB_RECIP_DEVICE, 0, + &devstat); + if (err) { + dev_err(&udev->dev, + "Failed to suspend device, error %d\n", + status); + goto done; + } + } } /* If the suspend failed, resume interfaces that did get suspended */ diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index f0dd08198d74..735e8ab2cc1f 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -1066,6 +1066,9 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type) portstatus = portchange = 0; status = hub_port_status(hub, port1, &portstatus, &portchange); + if (status) + goto abort; + if (udev || (portstatus & USB_PORT_STAT_CONNECTION)) dev_dbg(&port_dev->dev, "status %04x change %04x\n", portstatus, portchange); @@ -1198,7 +1201,7 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type) /* Scan all ports that need attention */ kick_hub_wq(hub); - + abort: if (type == HUB_INIT2 || type == HUB_INIT3) { /* Allow autosuspend if it was suppressed */ disconnected: