From: Santiago Piccinini Date: Sat, 9 Mar 2019 01:10:25 +0000 (-0300) Subject: ath79: add support for LibreRouter v1 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=24463d0d9479bf701e3aaa122f539a43cc97402b;p=openwrt%2Fstaging%2Fthess.git ath79: add support for LibreRouter v1 Hardware -------- SOC: QCA9558 RAM: 128M DDR2 Flash: 16MiB SPI-NOR ETH: QCA8337N: 2x 10/100/1000 PoE and PoE pass-through WiFi2: QCA9558 (bgn) 2T2R WiFi5: 2x mPCIE with AR9582 (an) 2T2R BTN: 1x Reset GPIO: multiple GPIO on header, PoE passthrough enable UART: 3.3V 115200 8N1 header on the board WDG: ATTiny13 watchdog JTAG: header on the board USB: 1x connector and 1x header on the board PoE: 10-32V input in ETH port 1, passthrough in port 2 mPCIE: 2x populated with radios (but replaceable) OpenWrt is preinstalled from factory. To install use -sysupgade.bin using the web interface or with sysupgrade -n. Flash from bootloader (in case failsafe does not work) 1. Connect the LibreRouter with a serial adapter (TTL voltage) to the UART header in the board. 2. Connect an ETH cable and configure static ip addres 192.168.1.10/24 3. Turn on the device and stop the bootloader sending any key through the serial interface. 4. Use a TFTP server to serve -sysupgrade.bin file. 5. Execute the following commands at the bootloader prompt: ath> tftp 82000000 -sysupgrade.bin ath> erase 0x9f050000 +$filesize ath> cp.b 0x82000000 0x9f050000 $filesize ath> bootm 0x9f050000 More docs * Bootloader https://github.com/librerouterorg/u-boot * Board details (schematics, gerbers): https://github.com/librerouterorg/board Signed-off-by: Santiago Piccinini --- diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79 index 262b54d3cc..495392b69a 100644 --- a/package/boot/uboot-envtools/files/ath79 +++ b/package/boot/uboot-envtools/files/ath79 @@ -19,6 +19,7 @@ buffalo,wzr-hp-ag300h) buffalo,bhr-4grv2|\ glinet,gl-ar300m-nand|\ glinet,gl-ar300m-nor|\ +librerouter,librerouter-v1|\ ocedo,koala|\ ocedo,raccoon|\ openmesh,om5p-ac-v2|\ diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index e66eb938fd..037e5777ed 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -118,6 +118,10 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan" ;; + librerouter,librerouter-v1) + ucidef_add_switch "switch0" \ + "0@eth0" "5:wan" "6@eth1" "4:lan" + ;; nec,wg800hp) ucidef_add_switch "switch0" \ "0@eth0" "2:lan" "3:lan" "4:lan" "1:wan" diff --git a/target/linux/ath79/base-files/etc/board.d/03_gpio_switches b/target/linux/ath79/base-files/etc/board.d/03_gpio_switches index 4f08fab525..dc5cbf6e9c 100755 --- a/target/linux/ath79/base-files/etc/board.d/03_gpio_switches +++ b/target/linux/ath79/base-files/etc/board.d/03_gpio_switches @@ -14,6 +14,9 @@ dlink,dir-825-c1|\ dlink,dir-835-a1) ucidef_add_gpio_switch "wan_led_auto" "WAN LED Auto" "20" "0" ;; +librerouter,librerouter-v1) + ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "1" "0" + ;; ubnt,nanostation-ac) ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "3" ;; diff --git a/target/linux/ath79/dts/qca9558_librerouter_librerouter-v1.dts b/target/linux/ath79/dts/qca9558_librerouter_librerouter-v1.dts new file mode 100644 index 0000000000..9e2f67977a --- /dev/null +++ b/target/linux/ath79/dts/qca9558_librerouter_librerouter-v1.dts @@ -0,0 +1,211 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "qca9557.dtsi" + +/ { + compatible = "librerouter,librerouter-v1", "qca,qca9558"; + model = "LibreRouter v1"; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + aliases { + led-boot = &system; + led-failsafe = &system; + led-running = &system; + led-upgrade = &system; + }; + + leds { + compatible = "gpio-leds"; + + system: system { + label = "librerouter-v1:green:system"; + gpios = <&gpio 23 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + wifi_green { + label = "librerouter-v1:green:wlan2g"; + gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + status_blue { + label = "librerouter-v1:blue:status"; + gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + }; + + }; + + button { + compatible = "gpio-keys"; + + reset { + label = "Reset"; + linux,code = ; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + }; + + watchdog { + compatible = "linux,wdt-gpio"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + hw_algo = "toggle"; + hw_margin_ms = <1000>; + always-running; + }; + +}; + +&pcie0 { + status = "okay"; + + wifi@0,0 { + compatible = "pci168c,0033"; + reg = <0x0000 0 0 0 0>; + }; +}; + +&pcie1 { + status = "okay"; + + wifi@0,0 { + compatible = "pci168c,0033"; + reg = <0x0000 0 0 0 0>; + }; +}; + +&uart { + status = "okay"; +}; + +&gpio { + status = "okay"; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb0 { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; +}; + +&usb_phy1 { + status = "okay"; +}; + +&usb1 { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; +}; + +&spi { + status = "okay"; + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x040000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x040000 0x010000>; + }; + + partition@50000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x050000 0x7c0000>; + }; + + partition@810000 { + label = "fw2"; + reg = <0x810000 0x7d0000>; + }; + + partition@fd0000 { + label = "res"; + reg = <0xfd0000 0x20000>; + }; + + ART: partition@ff0000 { + label = "ART"; + reg = <0xff0000 0x010000>; + read-only; + }; + }; + }; +}; + +&mdio0 { + status = "okay"; + + phy0: ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x04 0x87600000 /* PORT0: RGMII, MAC0/6 exchage, tx_delay 01, rx_delay 10 */ + 0x0c 0x00000080 /* PORT6: SGMII */ + 0x10 0x81000080 /* POWER_ON_STRAP: LED open drain, SerDes auto-neg disabled */ + 0x50 0xcf37cf37 /* LED_CTRL0 */ + 0x54 0xcf37cf37 /* LED_CTRL1 */ + 0x58 0xcf37cf37 /* LED_CTRL2 */ + 0x5c 0x0 /* LED_CTRL3 */ + 0x7c 0x0000007e /* PORT0_STATUS */ + 0x94 0x0000007e /* PORT6 STATUS */ + >; + }; +}; + +ð0 { + status = "okay"; + + pll-data = <0xa6000000 0x00000101 0x00001616>; + mtd-mac-address = <&ART 0x0>; + + phy-handle = <&phy0>; + +}; + +ð1 { + status = "okay"; + + phy-mode = "sgmii"; + pll-data = <0x03000101 0x00000101 0x00001616>; + mtd-mac-address = <&ART 0x6>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&wmac { + status = "okay"; + + mtd-cal-data = <&ART 0x1000>; + mtd-mac-address = <&ART 0xc>; +}; diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index c68e6a4a90..6e3dcf0bd8 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -394,6 +394,14 @@ define Device/iodata_wn-ag300dgr endef TARGET_DEVICES += iodata_wn-ag300dgr +define Device/librerouter_librerouter-v1 + ATH_SOC := qca9558 + DEVICE_TITLE := LibreRouter v1 + IMAGE_SIZE := 7936k + DEVICE_PACKAGES := kmod-usb-core kmod-usb2 +endef +TARGET_DEVICES += librerouter_librerouter-v1 + define Device/nec_wg800hp ATH_SOC := qca9563 DEVICE_TITLE := NEC Aterm WG800HP