From: Felix Fietkau Date: Thu, 20 Jul 2017 10:57:44 +0000 (+0200) Subject: ramips: add support for switching between 3-byte and 4-byte addressing on w25q256... X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=22d982ea003360d86ff1fef5114fb41dfa09ce9b;p=openwrt%2Fstaging%2Fansuel.git ramips: add support for switching between 3-byte and 4-byte addressing on w25q256 flash On some devices the flash chip needs to be in 3-byte addressing mode during reboot, otherwise the boot loader will fail to start. This mode however does not allow regular reads/writes onto the upper 16M half. W25Q256 has separate read commands for reading from >16M, however it does not have any separate write commands. This patch changes the code to leave the chip in 3-byte mode most of the time and only switch during erase/write cycles that go to >16M addresses. Signed-off-by: Felix Fietkau --- diff --git a/target/linux/ramips/patches-4.9/0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch b/target/linux/ramips/patches-4.9/0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch new file mode 100644 index 0000000000..e1e2bae461 --- /dev/null +++ b/target/linux/ramips/patches-4.9/0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch @@ -0,0 +1,214 @@ +mtd: spi-nor: add support for switching between 3-byte and 4-byte addressing on w25q256 flash + +On some devices the flash chip needs to be in 3-byte addressing mode during +reboot, otherwise the boot loader will fail to start. +This mode however does not allow regular reads/writes onto the upper 16M +half. W25Q256 has separate read commands for reading from >16M, however +it does not have any separate write commands. +This patch changes the code to leave the chip in 3-byte mode most of the +time and only switch during erase/write cycles that go to >16M +addresses. + +Signed-off-by: Felix Fietkau +--- +--- a/drivers/mtd/spi-nor/spi-nor.c ++++ b/drivers/mtd/spi-nor/spi-nor.c +@@ -85,6 +85,10 @@ struct flash_info { + * Use dedicated 4byte address op codes + * to support memory size above 128Mib. + */ ++#define SPI_NOR_4B_READ_OP BIT(12) /* ++ * Like SPI_NOR_4B_OPCODES, but for read ++ * op code only. ++ */ + }; + + #define JEDEC_MFR(info) ((info)->id[0]) +@@ -250,6 +254,15 @@ static inline u8 spi_nor_convert_3to4_er + ARRAY_SIZE(spi_nor_3to4_erase)); + } + ++static void spi_nor_set_4byte_read(struct spi_nor *nor, ++ const struct flash_info *info) ++{ ++ nor->addr_width = 3; ++ nor->ext_addr = 0; ++ nor->read_opcode = spi_nor_convert_3to4_read(nor->read_opcode); ++ nor->flags |= SNOR_F_4B_EXT_ADDR; ++} ++ + static void spi_nor_set_4byte_opcodes(struct spi_nor *nor, + const struct flash_info *info) + { +@@ -467,6 +480,36 @@ static int spi_nor_erase_sector(struct s + return nor->write_reg(nor, nor->erase_opcode, buf, nor->addr_width); + } + ++static int spi_nor_check_ext_addr(struct spi_nor *nor, u32 addr) ++{ ++ bool ext_addr; ++ int ret; ++ u8 cmd; ++ ++ if (!(nor->flags & SNOR_F_4B_EXT_ADDR)) ++ return 0; ++ ++ ext_addr = !!(addr & 0xff000000); ++ if (nor->ext_addr == ext_addr) ++ return 0; ++ ++ cmd = ext_addr ? SPINOR_OP_EN4B : SPINOR_OP_EX4B; ++ write_enable(nor); ++ ret = nor->write_reg(nor, cmd, NULL, 0); ++ if (ret) ++ return ret; ++ ++ cmd = 0; ++ ret = nor->write_reg(nor, SPINOR_OP_WREAR, &cmd, 1); ++ if (ret) ++ return ret; ++ ++ nor->addr_width = 3 + ext_addr; ++ nor->ext_addr = ext_addr; ++ write_disable(nor); ++ return 0; ++} ++ + /* + * Erase an address range on the nor chip. The address range may extend + * one or more erase sectors. Return an error is there is a problem erasing. +@@ -492,6 +535,10 @@ static int spi_nor_erase(struct mtd_info + if (ret) + return ret; + ++ ret = spi_nor_check_ext_addr(nor, addr + len); ++ if (ret) ++ return ret; ++ + /* whole-chip erase? */ + if (len == mtd->size && !(nor->flags & SNOR_F_NO_OP_CHIP_ERASE)) { + unsigned long timeout; +@@ -542,6 +589,7 @@ static int spi_nor_erase(struct mtd_info + write_disable(nor); + + erase_err: ++ spi_nor_check_ext_addr(nor, 0); + spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_ERASE); + + instr->state = ret ? MTD_ERASE_FAILED : MTD_ERASE_DONE; +@@ -834,7 +882,9 @@ static int spi_nor_lock(struct mtd_info + if (ret) + return ret; + ++ spi_nor_check_ext_addr(nor, ofs + len); + ret = nor->flash_lock(nor, ofs, len); ++ spi_nor_check_ext_addr(nor, 0); + + spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_UNLOCK); + return ret; +@@ -849,7 +899,9 @@ static int spi_nor_unlock(struct mtd_inf + if (ret) + return ret; + ++ spi_nor_check_ext_addr(nor, ofs + len); + ret = nor->flash_unlock(nor, ofs, len); ++ spi_nor_check_ext_addr(nor, 0); + + spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_LOCK); + return ret; +@@ -1151,7 +1203,7 @@ static const struct flash_info spi_nor_i + { "w25q80", INFO(0xef5014, 0, 64 * 1024, 16, SECT_4K) }, + { "w25q80bl", INFO(0xef4014, 0, 64 * 1024, 16, SECT_4K) }, + { "w25q128", INFO(0xef4018, 0, 64 * 1024, 256, SECT_4K) }, +- { "w25q256", INFO(0xef4019, 0, 64 * 1024, 512, SECT_4K) }, ++ { "w25q256", INFO(0xef4019, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_4B_READ_OP) }, + + /* Catalyst / On Semiconductor -- non-JEDEC */ + { "cat25c11", CAT25_INFO( 16, 8, 16, 1, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) }, +@@ -1205,6 +1257,9 @@ static int spi_nor_read(struct mtd_info + if (ret) + return ret; + ++ if (nor->flags & SNOR_F_4B_EXT_ADDR) ++ nor->addr_width = 4; ++ + while (len) { + loff_t addr = from; + +@@ -1229,6 +1284,18 @@ static int spi_nor_read(struct mtd_info + ret = 0; + + read_err: ++ if (nor->flags & SNOR_F_4B_EXT_ADDR) { ++ u8 val = 0; ++ ++ if ((from + len) & 0xff000000) { ++ write_enable(nor); ++ nor->write_reg(nor, SPINOR_OP_WREAR, &val, 1); ++ write_disable(nor); ++ } ++ ++ nor->addr_width = 3; ++ } ++ + spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_READ); + return ret; + } +@@ -1330,6 +1397,10 @@ static int spi_nor_write(struct mtd_info + if (ret) + return ret; + ++ ret = spi_nor_check_ext_addr(nor, to + len); ++ if (ret < 0) ++ return ret; ++ + for (i = 0; i < len; ) { + ssize_t written; + loff_t addr = to + i; +@@ -1377,6 +1448,7 @@ static int spi_nor_write(struct mtd_info + } + + write_err: ++ spi_nor_check_ext_addr(nor, 0); + spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_WRITE); + return ret; + } +@@ -1715,8 +1787,10 @@ int spi_nor_scan(struct spi_nor *nor, co + else if (mtd->size > 0x1000000) { + /* enable 4-byte addressing if the device exceeds 16MiB */ + nor->addr_width = 4; +- if (JEDEC_MFR(info) == SNOR_MFR_SPANSION || +- info->flags & SPI_NOR_4B_OPCODES) ++ if (info->flags & SPI_NOR_4B_READ_OP) ++ spi_nor_set_4byte_read(nor, info); ++ else if (JEDEC_MFR(info) == SNOR_MFR_SPANSION || ++ info->flags & SPI_NOR_4B_OPCODES) + spi_nor_set_4byte_opcodes(nor, info); + else + set_4byte(nor, info, 1); +--- a/include/linux/mtd/spi-nor.h ++++ b/include/linux/mtd/spi-nor.h +@@ -90,6 +90,7 @@ + /* Used for Macronix and Winbond flashes. */ + #define SPINOR_OP_EN4B 0xb7 /* Enter 4-byte mode */ + #define SPINOR_OP_EX4B 0xe9 /* Exit 4-byte mode */ ++#define SPINOR_OP_WREAR 0xc5 /* Write extended address register */ + + /* Used for Spansion flashes only. */ + #define SPINOR_OP_BRWR 0x17 /* Bank register write */ +@@ -141,6 +142,7 @@ enum spi_nor_option_flags { + SNOR_F_NO_OP_CHIP_ERASE = BIT(2), + SNOR_F_S3AN_ADDR_DEFAULT = BIT(3), + SNOR_F_READY_XSR_RDY = BIT(4), ++ SNOR_F_4B_EXT_ADDR = BIT(5), + }; + + /** +@@ -188,6 +190,7 @@ struct spi_nor { + enum read_mode flash_read; + bool sst_write_second; + u32 flags; ++ u8 ext_addr; + u8 cmd_buf[SPI_NOR_MAX_CMD_SIZE]; + + int (*prepare)(struct spi_nor *nor, enum spi_nor_ops ops); diff --git a/target/linux/ramips/patches-4.9/0054-mtd-add-chunked-read-io-to-m25p80.patch b/target/linux/ramips/patches-4.9/0054-mtd-add-chunked-read-io-to-m25p80.patch index 40994fb8d3..7f88ec52a7 100644 --- a/target/linux/ramips/patches-4.9/0054-mtd-add-chunked-read-io-to-m25p80.patch +++ b/target/linux/ramips/patches-4.9/0054-mtd-add-chunked-read-io-to-m25p80.patch @@ -1,6 +1,6 @@ --- a/drivers/mtd/spi-nor/spi-nor.c +++ b/drivers/mtd/spi-nor/spi-nor.c -@@ -1381,6 +1381,66 @@ write_err: +@@ -1453,6 +1453,67 @@ write_err: return ret; } @@ -8,6 +8,7 @@ + size_t *_retlen, const u_char *_buf) +{ + struct spi_nor *nor = mtd_to_spi_nor(mtd); ++ u32 addr_width = nor->addr_width + !!(nor->flags & SNOR_F_4B_EXT_ADDR); + int chunk_size; + int retlen = 0; + int ret; @@ -16,8 +17,8 @@ + if (!chunk_size) + chunk_size = _len; + -+ if (nor->addr_width > 3) -+ chunk_size -= nor->addr_width - 3; ++ if (addr_width > 3) ++ chunk_size -= addr_width - 3; + + while (retlen < _len) { + size_t len = min_t(int, chunk_size, _len - retlen); @@ -67,7 +68,7 @@ static int macronix_quad_enable(struct spi_nor *nor) { int ret, val; -@@ -1630,10 +1690,12 @@ int spi_nor_scan(struct spi_nor *nor, co +@@ -1702,10 +1763,12 @@ int spi_nor_scan(struct spi_nor *nor, co } /* sst nor chips use AAI word program */ @@ -82,7 +83,7 @@ if (info->flags & USE_FSR) nor->flags |= SNOR_F_USE_FSR; -@@ -1663,11 +1725,20 @@ int spi_nor_scan(struct spi_nor *nor, co +@@ -1735,11 +1798,20 @@ int spi_nor_scan(struct spi_nor *nor, co mtd->writebufsize = nor->page_size; if (np) { @@ -105,15 +106,15 @@ nor->flash_read = SPI_NOR_FAST; --- a/include/linux/mtd/spi-nor.h +++ b/include/linux/mtd/spi-nor.h -@@ -141,6 +141,7 @@ enum spi_nor_option_flags { - SNOR_F_NO_OP_CHIP_ERASE = BIT(2), +@@ -143,6 +143,7 @@ enum spi_nor_option_flags { SNOR_F_S3AN_ADDR_DEFAULT = BIT(3), SNOR_F_READY_XSR_RDY = BIT(4), -+ SNOR_F_SST = BIT(5), + SNOR_F_4B_EXT_ADDR = BIT(5), ++ SNOR_F_SST = BIT(6), }; /** -@@ -180,6 +181,7 @@ struct spi_nor { +@@ -182,6 +183,7 @@ struct spi_nor { struct mutex lock; struct device *dev; u32 page_size;