From: Jackson Lim Date: Sat, 20 Jul 2019 07:37:12 +0000 (+0800) Subject: ath79: add support for D-Link DIR-842 C2 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=209b36825458a439fb9f0edd36f11e6528400f87;p=openwrt%2Fstaging%2Faparcar.git ath79: add support for D-Link DIR-842 C2 Hardware spec of DIR-842 C2: SoC: QCA9563 DRAM: 128MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337N WiFi 5.8GHz: QCA9888 WiFi 2.4Ghz: QCA9563 USB: 2.0 Flash instructions: 1. Upgrade the factory.bin through the factory web interface or the u-boot failsafe interface. The firmware will boot up correctly for the first time. Do not power off the device after OpenWrt has booted. Otherwise the u-boot will enter failsafe mode as the checksum of the firmware has been changed. 2. Upgrade the sysupgrade.bin in OpenWrt. After upgrading completes the u-boot won't complain about the firmware checksum and it's OK to use now. 3. If you powered off the device before upgrading the sysupgrade.bin, just upgrade the factory.bin through the u-boot failsafe interface and then goto step 2. Signed-off-by: Jackson Lim [Reword reset-hog comment, fix formatting] Signed-off-by: David Bauer --- diff --git a/target/linux/ath79/base-files/etc/board.d/01_leds b/target/linux/ath79/base-files/etc/board.d/01_leds index 16eb2d01e3..d24a42d239 100755 --- a/target/linux/ath79/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/base-files/etc/board.d/01_leds @@ -59,6 +59,7 @@ comfast,cf-e5) ucidef_set_led_rssi "rssimedium" "RSSIMEDIUM" "$boardname:blue:rssi1" "wlan0" "33" "100" ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "$boardname:blue:rssi2" "wlan0" "66" "100" ;; +dlink,dir-842-c2|\ dlink,dir-859-a1) ucidef_set_led_switch "internet" "WAN" "$boardname:green:internet" "switch0" "0x20" ;; diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index ed33ff5aad..41ceb12ee5 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -112,6 +112,7 @@ ath79_setup_interfaces() ;; dlink,dir-825-c1|\ dlink,dir-835-a1|\ + dlink,dir-842-c2|\ dlink,dir-859-a1|\ engenius,epg5000|\ tplink,archer-c2-v3|\ @@ -303,6 +304,7 @@ ath79_setup_macs() lan_mac=$(mtd_get_mac_text "mac" 4) wan_mac=$(mtd_get_mac_text "mac" 24) ;; + dlink,dir-842-c2|\ dlink,dir-859-a1|\ nec,wg1200cr|\ wd,mynet-n750) diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom index f049dbd46a..7850c689b8 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom @@ -105,6 +105,7 @@ case "$FIRMWARE" in ath9k_eeprom_extract "art" 4096 1088 ath9k_patch_fw_mac_crc $(mtd_get_mac_text "mac" 4) 2 ;; + dlink,dir-842-c2|\ dlink,dir-859-a1|\ nec,wg1200cr|\ wd,mynet-n750) diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index d45003c837..41186853ef 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -189,6 +189,7 @@ case "$FIRMWARE" in ;; "ath10k/pre-cal-pci-0000:00:00.0.bin") case $board in + dlink,dir-842-c2|\ nec,wg1200cr) ath10kcal_extract "art" 20480 12064 ath10kcal_patch_mac_crc $(mtd_get_mac_ascii devdata wlan5mac) diff --git a/target/linux/ath79/dts/qca9563_dlink_dir-842-c2.dts b/target/linux/ath79/dts/qca9563_dlink_dir-842-c2.dts new file mode 100644 index 0000000000..49e3855268 --- /dev/null +++ b/target/linux/ath79/dts/qca9563_dlink_dir-842-c2.dts @@ -0,0 +1,188 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "qca956x.dtsi" + +/ { + model = "D-Link DIR-842 C2"; + compatible = "dlink,dir-842-c2", "qca,qca9563"; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + wps { + label = "dir-842-c2:green:wps"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + + power: power { + label = "dir-842-c2:green:power"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + internet { + label = "dir-842-c2:green:internet"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + }; + + wlan { + label = "dir-842-c2:green:wlan"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + }; + + keys { + compatible = "gpio-keys"; + + wps { + linux,code = ; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + reset { + linux,code = ; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; + + // Pull up on boot - otherwise the reset button won't work + reset-button { + gpio-hog; + output-high; + gpios = <11 GPIO_ACTIVE_LOW>; + line-name = "reset-button"; + }; +}; + +&uart { + status = "okay"; +}; + +&pcie { + status = "okay"; +}; + +&spi { + status = "okay"; + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <30000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x40000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x040000 0x10000>; + read-only; + }; + + partition@50000 { + label = "devdata"; + reg = <0x050000 0x10000>; + read-only; + }; + + partition@60000 { + label = "devconf"; + reg = <0x060000 0x10000>; + read-only; + }; + + partition@70000 { + label = "misc"; + reg = <0x070000 0x10000>; + read-only; + }; + + partition@80000 { + compatible = "seama"; + label = "firmware"; + reg = <0x080000 0xf50000>; + }; + + art: partition@fd0000 { + label = "art"; + reg = <0xfd0000 0x010000>; + read-only; + }; + + partition@fe0000 { + label = "reserved"; + reg = <0xfe0000 0x20000>; + read-only; + }; + }; + }; +}; + +&mdio0 { + status = "okay"; + + phy-mask = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + qca,mib-poll-interval = <500>; + + qca,ar8327-initvals = < + 0x04 0x00080080 /* PORT0 PAD MODE CTRL */ + 0x10 0x81000080 /* POWER_ON_STRIP */ + 0x50 0xcc35cc35 /* LED_CTRL0 */ + 0x54 0xcb37cb37 /* LED_CTRL1 */ + 0x58 0x00000000 /* LED_CTRL2 */ + 0x5c 0x00f3cf00 /* LED_CTRL3 */ + 0x7c 0x0000007e /* PORT0_STATUS */ + >; + }; +}; + +ð0 { + status = "okay"; + + pll-data = <0x03000101 0x00000101 0x00001919>; + + phy-mode = "sgmii"; + phy-handle = <&phy0>; +}; + +&wmac { + status = "okay"; + qca,no-eeprom; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index 64c92c89dc..c5807f2c78 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -355,6 +355,29 @@ define Device/dlink_dir-859-a1 endef TARGET_DEVICES += dlink_dir-859-a1 +define Device/dlink_dir-842-c2 + ATH_SOC := qca9563 + DEVICE_VENDOR := D-Link + DEVICE_MODEL := DIR-842 + DEVICE_VARIANT := C2 + KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma + KERNEL_INITRAMFS := $$(KERNEL) | seama + IMAGES += factory.bin + SEAMA_MTDBLOCK := 5 + SEAMA_SIGNATURE := wrgac65_dlink.2015_dir842 + # 64 bytes offset: + # - 28 bytes seama_header + # - 36 bytes of META data (4-bytes aligned) + IMAGE/default := append-kernel | uImage lzma | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs + IMAGE/sysupgrade.bin := \ + $$(IMAGE/default) | seama | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE) + IMAGE/factory.bin := \ + $$(IMAGE/default) | pad-rootfs -x 64 | seama | seama-seal | check-size $$$$(IMAGE_SIZE) + IMAGE_SIZE := 15680k + DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct +endef +TARGET_DEVICES += dlink_dir-842-c2 + define Device/elecom_wrc-1750ghbk2-i ATH_SOC := qca9563 DEVICE_VENDOR := ELECOM