From: Gary Cooper Date: Mon, 4 Jan 2021 17:27:50 +0000 (+0300) Subject: ipq806x: add support for TP-Link Talon AD7200 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=1a775a4fd0339b485f48a864e2cf9e8794bfe4cb;p=openwrt%2Fstaging%2Fmkresin.git ipq806x: add support for TP-Link Talon AD7200 Device hardware: https://deviwiki.com/wiki/TP-LINK_AD7200_(Talon) The Talon AD7200 is basically an Archer C2600 with a third PCIe lane and an 802.11ad radio. It looks like the Archers C2600/5400 but the housing is slightly larger. Specifications -------------- - IPQ8064 dual-core 1400MHz - QCA9988 2.4GHz WiFi - QCA9990 5GHz WiFi - QCA9500 60GHz WiFi - 32MB SPI Flash - 512MiB RAM - 5 GBit Ports (QCA8337) Installation ------------ Installation is possible from the OEM web interface. Sysupgrade is possible. TFTP recovery is possible. - Image: AD7200_1.0_tp_recovery.bin Notes - This will be the first 802.11ad device supported by mainline. Signed-off-by: Gary Cooper --- diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds index fed821663a..a03a056d83 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/01_leds +++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds @@ -39,6 +39,15 @@ netgear,r7800) ucidef_set_led_switch "wan" "WAN" "white:wan" "switch0" "0x20" ucidef_set_led_ide "esata" "eSATA" "white:esata" ;; +tplink,ad7200) + ucidef_set_led_usbport "usb1" "USB 1" "blue:usb_1" "usb1-port1" "usb2-port1" + ucidef_set_led_usbport "usb2" "USB 2" "blue:usb_3" "usb3-port1" "usb4-port1" + ucidef_set_led_switch "wan" "wan" "blue:wan" "switch0" "0x02" + ucidef_set_led_switch "lan" "lan" "blue:lan" "switch0" "0x3c" + ucidef_set_led_wlan "wlan2g" "wlan2g" "blue:wlan2g" "phy2tpt" + ucidef_set_led_wlan "wlan5g" "wlan5g" "blue:wlan5g" "phy1tpt" + ucidef_set_led_netdev "wlan60g" "wlan60g" "blue:wlan60g" "wlan0" + ;; tplink,c2600) ucidef_set_led_usbport "usb1" "USB 1" "white:usb_2" "usb1-port1" "usb2-port1" ucidef_set_led_usbport "usb2" "USB 2" "white:usb_4" "usb3-port1" "usb4-port1" diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network index 10b2ec0148..fbf56c5e0c 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/02_network +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network @@ -51,6 +51,7 @@ nec,wg2600hp3) "2:lan" "3:lan" "4:lan" "5:lan" "0@eth1" "1:wan" "6@eth0" ;; netgear,r7800 |\ +tplink,ad7200 |\ tplink,c2600) ucidef_add_switch "switch0" \ "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "6@eth1" "5:wan" "0@eth0" diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 8788fc92f6..3befc40630 100644 --- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -35,6 +35,7 @@ case "$FIRMWARE" in caldata_extract "art" 0x1000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x6) +1) ;; + tplink,ad7200 |\ tplink,c2600) caldata_extract "radio" 0x1000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary default-mac 0x8) -1) @@ -74,6 +75,7 @@ case "$FIRMWARE" in caldata_extract "art" 0x5000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x6) +2) ;; + tplink,ad7200 |\ tplink,c2600) caldata_extract "radio" 0x5000 0x2f20 ath10k_patch_mac $(mtd_get_mac_binary default-mac 0x8) diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh index f5d6c5d55d..4dc612492c 100644 --- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh @@ -43,6 +43,7 @@ platform_do_upgrade() { linksys,ea8500) platform_do_upgrade_linksys "$1" ;; + tplink,ad7200 |\ tplink,c2600) PART_NAME="os-image:rootfs" MTD_CONFIG_ARGS="-s 0x200000" diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ad7200.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ad7200.dts new file mode 100644 index 0000000000..e5bdc32114 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ad7200.dts @@ -0,0 +1,440 @@ +//SPDX-License-Identifier: GPL-2.0-or-later OR MIT +#include "qcom-ipq8064-v2.0.dtsi" + +#include + +/ { + model = "TP-Link Talon AD7200"; + compatible = "tplink,ad7200", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + aliases { + mdio-gpio0 = &mdio0; + + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + label-mac-device = &gmac2; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + wifi { + label = "wifi"; + gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 7 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + ledgeneral { + label = "ledswitch"; + gpios = <&qcom_pinmux 53 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + lan { + label = "blue:lan"; + gpios = <&qcom_pinmux 2 GPIO_ACTIVE_HIGH>; + }; + + usb1 { + label = "blue:usb_1"; + gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; + }; + + usb3 { + label = "blue:usb_3"; + gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>; + }; + + wps { + label = "blue:wps"; + gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>; + }; + + wan_orange { + label = "orange:wan"; + gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>; + }; + + wan_blue { + label = "blue:wan"; + gpios = <&qcom_pinmux 33 GPIO_ACTIVE_LOW>; + }; + + power: status { + label = "blue:status"; + gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>; + }; + + wlan2g { + label = "blue:wlan2g"; + gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>; + + }; + + wlan5g { + label = "blue:wlan5g"; + gpios = <&qcom_pinmux 15 GPIO_ACTIVE_HIGH>; + + }; + + wlan60g { + label = "blue:wlan60g"; + gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&qcom_pinmux { + button_pins: button_pins { + mux { + pins = "gpio53", "gpio54", "gpio67"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio2", "gpio8", "gpio15", "gpio16", "gpio17", "gpio26", + "gpio33", "gpio55", "gpio56", "gpio66"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19", "gpio21"; + function = "gsbi5"; + bias-pull-down; + }; + + data { + pins = "gpio18", "gpio19"; + drive-strength = <10>; + }; + + cs { + pins = "gpio20"; + function = "gpio"; + drive-strength = <10>; + bias-pull-up; + }; + + clk { + pins = "gpio21"; + drive-strength = <12>; + }; + }; + + usb0_pwr_en_pin: usb0_pwr_en_pin { + mux { + pins = "gpio25"; + function = "gpio"; + drive-strength = <10>; + bias-pull-up; + output-high; + }; + }; + + usb1_pwr_en_pin: usb1_pwr_en_pin { + mux { + pins = "gpio23"; + function = "gpio"; + drive-strength = <10>; + bias-pull-up; + output-high; + }; + }; +}; + +&gsbi5 { + qcom,mode = ; + status = "okay"; + + spi4: spi@1a280000 { + status = "okay"; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; + + m25p80@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <50000000>; + reg = <0>; + + SBL1@0 { + label = "SBL1"; + reg = <0x0 0x20000>; + read-only; + }; + + MIBIB@20000 { + label = "MIBIB"; + reg = <0x20000 0x20000>; + read-only; + }; + + SBL2@40000 { + label = "SBL2"; + reg = <0x40000 0x20000>; + read-only; + }; + + SBL3@60000 { + label = "SBL3"; + reg = <0x60000 0x30000>; + read-only; + }; + + DDRCONFIG@90000 { + label = "DDRCONFIG"; + reg = <0x90000 0x10000>; + read-only; + }; + + SSD@a0000 { + label = "SSD"; + reg = <0xa0000 0x10000>; + read-only; + }; + + TZ@b0000 { + label = "TZ"; + reg = <0xb0000 0x30000>; + read-only; + }; + + RPM@e0000 { + label = "RPM"; + reg = <0xe0000 0x20000>; + read-only; + }; + + fs-uboot@100000 { + label = "fs-uboot"; + reg = <0x100000 0x70000>; + read-only; + }; + + uboot-env@170000 { + label = "uboot-env"; + reg = <0x170000 0x40000>; + read-only; + }; + + radio@1b0000 { + label = "radio"; + reg = <0x1b0000 0x40000>; + read-only; + }; + + os-image@1f0000 { + label = "os-image"; + reg = <0x1f0000 0x400000>; + }; + + rootfs@5f0000 { + label = "rootfs"; + reg = <0x5f0000 0x1900000>; + }; + + defaultmac: default-mac@1ef0000 { + label = "default-mac"; + reg = <0x1ef0000 0x00200>; + read-only; + }; + + pin@1ef0200 { + label = "pin"; + reg = <0x1ef0200 0x00200>; + read-only; + }; + + device-id@1ef0400 { + label = "device-id"; + reg = <0x1ef0400 0x00200>; + read-only; + }; + + product-info@1ef0600 { + label = "product-info"; + reg = <0x1ef0600 0x0fa00>; + read-only; + }; + + partition-table@1f00000 { + label = "partition-table"; + reg = <0x1f00000 0x10000>; + read-only; + }; + + soft-version@1f10000 { + label = "soft-version"; + reg = <0x1f10000 0x10000>; + read-only; + }; + + support-list@1f20000 { + label = "support-list"; + reg = <0x1f20000 0x10000>; + read-only; + }; + + profile@1f30000 { + label = "profile"; + reg = <0x1f30000 0x10000>; + read-only; + }; + + default-config@1f40000 { + label = "default-config"; + reg = <0x1f40000 0x10000>; + read-only; + }; + + user-config@1f50000 { + label = "user-config"; + reg = <0x1f50000 0x40000>; + read-only; + }; + + qos-db@1f90000 { + label = "qos-db"; + reg = <0x1f90000 0x40000>; + read-only; + }; + + usb-config@1fd0000 { + label = "usb-config"; + reg = <0x1fd0000 0x10000>; + read-only; + }; + + log@1fe0000 { + label = "log"; + reg = <0x1fe0000 0x20000>; + read-only; + }; + }; + }; +}; + +&usb3_0 { + status = "okay"; + + pinctrl-0 = <&usb0_pwr_en_pin>; + pinctrl-names = "default"; +}; + +&usb3_1 { + status = "okay"; + + pinctrl-0 = <&usb1_pwr_en_pin>; + pinctrl-names = "default"; +}; + +&pcie0 { + status = "okay"; +}; + +&pcie1 { + status = "okay"; + max-link-speed = <1>; +}; + +&pcie2 { + status = "okay"; + max-link-speed = <1>; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0x6a545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; + + phy4: ethernet-phy@4 { + reg = <4>; + }; +}; + +&gmac1 { + status = "okay"; + phy-mode = "rgmii"; + qcom,id = <1>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + mtd-mac-address = <&defaultmac 0x8>; + mtd-mac-address-increment = <1>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac2 { + status = "okay"; + phy-mode = "sgmii"; + qcom,id = <2>; + + mtd-mac-address = <&defaultmac 0x8>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&adm_dma { + status = "okay"; +}; diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile index 80bfec5ad9..876f337bba 100644 --- a/target/linux/ipq806x/image/Makefile +++ b/target/linux/ipq806x/image/Makefile @@ -333,6 +333,21 @@ define Device/qcom_ipq8064-db149 endef TARGET_DEVICES += qcom_ipq8064-db149 +define Device/tplink_ad7200 + $(call Device/TpSafeImage) + DEVICE_VENDOR := TP-Link + DEVICE_MODEL := Talon AD7200 + DEVICE_VARIANT := v1 + SOC := qcom-ipq8064 + BLOCKSIZE := 128k + PAGESIZE := 2048 + BOARD_NAME := ad7200 + SUPPORTED_DEVICES += ad7200 + TPLINK_BOARD_ID := AD7200 + DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct kmod-wil6210 +endef +TARGET_DEVICES += tplink_ad7200 + define Device/tplink_c2600 $(call Device/TpSafeImage) DEVICE_VENDOR := TP-Link diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c index deba84c6d1..785ff39642 100644 --- a/tools/firmware-utils/src/tplink-safeloader.c +++ b/tools/firmware-utils/src/tplink-safeloader.c @@ -668,6 +668,50 @@ static struct device_info boards[] = { .last_sysupgrade_partition = "support-list", }, + /** Firmware layout for the AD7200 */ + { + .id = "AD7200", + .vendor = "", + .support_list = + "SupportList:\r\n" + "{product_name:Talon AD7200,product_ver:1.0.0,special_id:00000000}\r\n", + .part_trail = 0x00, + .soft_ver = NULL, + + .partitions = { + {"SBL1", 0x00000, 0x20000}, + {"MIBIB", 0x20000, 0x20000}, + {"SBL2", 0x40000, 0x20000}, + {"SBL3", 0x60000, 0x30000}, + {"DDRCONFIG", 0x90000, 0x10000}, + {"SSD", 0xa0000, 0x10000}, + {"TZ", 0xb0000, 0x30000}, + {"RPM", 0xe0000, 0x20000}, + {"fs-uboot", 0x100000, 0x70000}, + {"uboot-env", 0x170000, 0x40000}, + {"radio", 0x1b0000, 0x40000}, + {"os-image", 0x1f0000, 0x400000}, + {"file-system", 0x5f0000, 0x1900000}, + {"default-mac", 0x1ef0000, 0x00200}, + {"pin", 0x1ef0200, 0x00200}, + {"device-id", 0x1ef0400, 0x00200}, + {"product-info", 0x1ef0600, 0x0fa00}, + {"partition-table", 0x1f00000, 0x10000}, + {"soft-version", 0x1f10000, 0x10000}, + {"support-list", 0x1f20000, 0x10000}, + {"profile", 0x1f30000, 0x10000}, + {"default-config", 0x1f40000, 0x10000}, + {"user-config", 0x1f50000, 0x40000}, + {"qos-db", 0x1f90000, 0x40000}, + {"usb-config", 0x1fd0000, 0x10000}, + {"log", 0x1fe0000, 0x20000}, + {NULL, 0, 0} + }, + + .first_sysupgrade_partition = "os-image", + .last_sysupgrade_partition = "file-system" + }, + /** Firmware layout for the C2600 */ { .id = "C2600",