From: Kyle Hendry Date: Sun, 18 Feb 2024 20:26:38 +0000 (-0800) Subject: bmips: add support for SmartRG SR505n X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=1a6954337634474e6c42dec6023daa7af1d52432;p=openwrt%2Fstaging%2Fpepe2k.git bmips: add support for SmartRG SR505n Specifications: - SoC: Broadcom BCM63168 dual 400MHz MIPS - Flash: 16MB SPI NOR W25Q128WFG - RAM: 128MB DDR3 W631GG6KB-15 - Ethernet: 1x 1000M, 3x 100M - Wifi: BCM435F - 1x USB 2.0 port - 3x Button - 12x LED Flashing via serial - Connect to the 3.3V TTL UART on the board (J6 pinout Vcc Rx Tx Gnd) at 115200-8-N-1 - Press any key in the serial console when powering up the board to enter the CFE prompt - Configure an interface on your workstation to static IP 192.168.1.100 and connect it to the board - Start a TFTP server with the firmware image - On the CFE prompt, enter the command "f 192.168.1.100:openwrt-bmips-bcm63268-smartrg_sr505n-squashfs-cfe.bin" Signed-off-by: Kyle Hendry [Remove unneeded LED labels] Signed-off-by: Álvaro Fernández Rojas --- diff --git a/target/linux/bmips/bcm63268/base-files/etc/board.d/01_leds b/target/linux/bmips/bcm63268/base-files/etc/board.d/01_leds index d5b65a9c0f..8af1b77504 100644 --- a/target/linux/bmips/bcm63268/base-files/etc/board.d/01_leds +++ b/target/linux/bmips/bcm63268/base-files/etc/board.d/01_leds @@ -9,6 +9,9 @@ case "$(board_name)" in comtrend,vr-3032u) ucidef_set_led_usbport "usb" "USB" "green:usb" "usb1-port1" "usb2-port1" ;; +smartrg,sr505n) + ucidef_set_led_usbport "usb" "USB" "green:usb" "usb1-port1" + ;; sercomm,h500-s-lowi |\ sercomm,h500-s-vfes) ucidef_set_led_netdev "wan" "WAN" "green:internet" "wan" diff --git a/target/linux/bmips/bcm63268/base-files/etc/board.d/02_network b/target/linux/bmips/bcm63268/base-files/etc/board.d/02_network index 7fb9333cc1..74b74691cb 100644 --- a/target/linux/bmips/bcm63268/base-files/etc/board.d/02_network +++ b/target/linux/bmips/bcm63268/base-files/etc/board.d/02_network @@ -5,7 +5,8 @@ board_config_update case "$(board_name)" in -comtrend,vr-3032u) +comtrend,vr-3032u |\ +smartrg,sr505n) ucidef_set_bridge_device switch ucidef_set_interface_lan "lan1 lan2 lan3 lan4" ;; diff --git a/target/linux/bmips/dts/bcm63168-smartrg-sr505n.dts b/target/linux/bmips/dts/bcm63168-smartrg-sr505n.dts new file mode 100644 index 0000000000..571289b4c6 --- /dev/null +++ b/target/linux/bmips/dts/bcm63168-smartrg-sr505n.dts @@ -0,0 +1,238 @@ +// SPDX-License-Identifier: GPL-2.0-or-later + +#include "bcm63268.dtsi" + +/ { + model = "SmartRG SR505n"; + compatible = "smartrg,sr505n", "brcm,bcm63168", "brcm,bcm63268"; + + aliases { + led-boot = &led_power_green; + led-failsafe = &led_power_red; + led-running = &led_power_green; + led-upgrade = &led_power_green; + }; + + keys { + compatible = "gpio-keys-polled"; + poll-interval = <100>; + + reset { + label = "reset"; + gpios = <&gpio 32 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + + wps { + label = "wps"; + gpios = <&gpio 33 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + + wlan { + label = "wlan"; + gpios = <&gpio 34 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + }; +}; + +&ehci { + status = "okay"; +}; + +ðernet { + status = "okay"; + + nvmem-cells = <&macaddr_cfe_6a0>; + nvmem-cell-names = "mac-address"; +}; + +&hsspi { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + spi-max-frequency = <16666667>; + spi-tx-bus-width = <2>; + spi-rx-bus-width = <2>; + reg = <0>; + + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "cfe"; + reg = <0x000000 0x010000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_cfe_6a0: macaddr@6a0 { + reg = <0x6a0 0x6>; + }; + }; + }; + + partition@10000 { + compatible = "brcm,bcm963xx-imagetag"; + label = "firmware"; + reg = <0x010000 0xfd0000>; + }; + + partition@fe0000 { + label = "nvram"; + reg = <0xfe0000 0x020000>; + }; + }; + }; +}; + +&leds { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds>; + + wps_green@1 { + reg = <1>; + active-low; + function = LED_FUNCTION_WPS; + color = ; + }; + + inet_green@8 { + reg = <8>; + active-low; + label = "green:inet"; + }; + + lan2_green@9 { + /* EPHY1 Act */ + reg = <9>; + brcm,hardware-controlled; + }; + + lan3_green@10 { + /* EPHY2 Act */ + reg = <10>; + brcm,hardware-controlled; + }; + + lan4_green@11 { + /* EPHY3 Act */ + reg = <11>; + brcm,hardware-controlled; + }; + + lan1_green@12 { + /* GPHY0 Act */ + reg = <12>; + brcm,hardware-controlled; + }; + + dsl_green@14 { + reg = <14>; + active-low; + label = "green:dsl"; + }; + + inet_red@15 { + reg = <15>; + active-low; + label = "red:inet"; + }; + + usb_green@16 { + reg = <16>; + active-low; + function = LED_FUNCTION_USB; + color = ; + }; + + led_power_green: power_green@20 { + reg = <20>; + active-low; + function = LED_FUNCTION_POWER; + color = ; + }; + + led_power_red: power_red@21 { + reg = <21>; + active-low; + function = LED_FUNCTION_POWER; + color = ; + panic-indicator; + }; +}; + +&pinctrl { + pinctrl_leds: leds { + function = "led"; + pins = "gpio1", "gpio8", + "gpio9", "gpio10", + "gpio11", "gpio12", + "gpio14", "gpio15", + "gpio16", "gpio20", + "gpio21"; + }; +}; + +&ohci { + status = "okay"; +}; + +&switch0 { + ports { + port@0 { + reg = <0>; + label = "lan2"; + + phy-handle = <&phy1>; + phy-mode = "mii"; + }; + + port@1 { + reg = <1>; + label = "lan3"; + + phy-handle = <&phy2>; + phy-mode = "mii"; + }; + + port@2 { + reg = <2>; + label = "lan4"; + + phy-handle = <&phy3>; + phy-mode = "mii"; + }; + + port@3 { + reg = <3>; + label = "lan1"; + + phy-handle = <&phy4>; + phy-mode = "gmii"; + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&usbh { + status = "okay"; +}; diff --git a/target/linux/bmips/image/bcm63268.mk b/target/linux/bmips/image/bcm63268.mk index 941e83f71b..be3403174e 100644 --- a/target/linux/bmips/image/bcm63268.mk +++ b/target/linux/bmips/image/bcm63268.mk @@ -100,3 +100,17 @@ define Device/sercomm_shg2500 SERCOMM_SWVER := 3207 endef TARGET_DEVICES += sercomm_shg2500 + +define Device/smartrg_sr505n + $(Device/bcm63xx-cfe) + DEVICE_VENDOR := SmartRG + DEVICE_MODEL := SR505n + DEVICE_LOADADDR := $(KERNEL_LOADADDR) + CHIP_ID := 63268 + SOC := bcm63168 + CFE_BOARD_ID := 963168MBV_17AZZ + FLASH_MB := 16 + DEVICE_PACKAGES += $(USB2_PACKAGES) \ + kmod-leds-bcm6328 +endef +TARGET_DEVICES += smartrg_sr505n