From: INAGAKI Hiroshi Date: Fri, 15 Jun 2018 15:27:51 +0000 (+0900) Subject: ramips: add support for ELECOM WRC-1167GHBK2-S X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=189815462cda469f6bba2609d65a4591f83418e1;p=openwrt%2Fstaging%2Fstintel.git ramips: add support for ELECOM WRC-1167GHBK2-S ELECOM WRC-1167GHBK2-S is a 2.4/5 GHz band 11ac router, based on MediaTek MT7621A. Specification: - MT7621A (2-Cores, 4-Threads) - 128 MB of RAM (DDR3) - 16 MB of Flash (SPI) - 2T2R 2.4/5 GHz - MediaTek MT7615D - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 2x keys - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - baudrate: 57600 bps Flash instruction using factory image: 1. Rename the factory image to "wrc-1167ghbk2-s_v0.00.bin" 2. Connect the computer to the LAN port of WRC-1167GHBK2-S 3. Connect power cable to WRC-1167GHBK2-S and turn on it 4. Access to "http://192.168.2.1/details.html" and open firmware update page ("手動更新（アップデート）") 5. Select the factory image and click apply ("適用") button 6. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi --- diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds index a9a68f6eef..54504c6ee8 100755 --- a/target/linux/ramips/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/base-files/etc/board.d/01_leds @@ -168,6 +168,7 @@ dlink,dwr-921-c1) ucidef_set_led_default "sigstrength" "Signal Strength" "$boardname:green:sigstrength" "0" ;; dir-810l|\ +elecom,wrc-1167ghbk2-s|\ iodata,wn-gx300gr|\ mzk-750dhp|\ mzk-dp150n|\ diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 49d7f9220a..de086cf248 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -226,7 +226,8 @@ ramips_setup_interfaces() ucidef_add_switch "switch0" \ "1:lan:3" "2:lan:4" "3:lan:1" "4:lan:2" "0:wan" "6@eth0" ;; - dir-860l-b1) + dir-860l-b1|\ + elecom,wrc-1167ghbk2-s) ucidef_add_switch "switch0" \ "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "0:wan" "6@eth0" ;; @@ -450,6 +451,10 @@ ramips_setup_macs() e1700) wan_mac=$(mtd_get_mac_ascii config WAN_MAC_ADDR) ;; + elecom,wrc-1167ghbk2-s|\ + sk-wb8) + wan_mac=$(mtd_get_mac_binary factory 57350) + ;; gl-mt300n-v2|\ whr-g300n) wan_mac=$(mtd_get_mac_binary factory 4) @@ -514,9 +519,6 @@ ramips_setup_macs() lan_mac=$(macaddr_setbit_la "$lan_mac") wan_mac=$(mtd_get_mac_binary factory 32772) ;; - sk-wb8) - wan_mac=$(mtd_get_mac_binary factory 57350) - ;; tew-691gr) wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 4)" 3) ;; diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh index e5373a80d1..eb06442979 100644 --- a/target/linux/ramips/base-files/etc/diag.sh +++ b/target/linux/ramips/base-files/etc/diag.sh @@ -22,6 +22,7 @@ get_status_led() { dch-m225|\ dir-860l-b1|\ e1700|\ + elecom,wrc-1167ghbk2-s|\ ex2700|\ ex3700|\ fonera20n|\ diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh index 9b17ecbebb..c094e41935 100755 --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh @@ -54,6 +54,7 @@ platform_check_image() { dir-810l|\ duzun-dm06|\ e1700|\ + elecom,wrc-1167ghbk2-s|\ esr-9753|\ ew1200|\ ex2700|\ diff --git a/target/linux/ramips/dts/WRC-1167GHBK2-S.dts b/target/linux/ramips/dts/WRC-1167GHBK2-S.dts new file mode 100644 index 0000000000..7b1cfd7304 --- /dev/null +++ b/target/linux/ramips/dts/WRC-1167GHBK2-S.dts @@ -0,0 +1,144 @@ +/dts-v1/; + +#include "mt7621.dtsi" + +#include +#include + +/ { + compatible = "elecom,wrc-1167ghbk2-s", "mediatek,mt7621-soc"; + model = "ELECOM WRC-1167GHBK2-S"; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,57600"; + }; + + gpio-leds { + compatible = "gpio-leds"; + + wlan2g { + label = "wrc-1167ghbk2-s:white:wlan2g"; + gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; + }; + + wlan5g { + label = "wrc-1167ghbk2-s:white:wlan5g"; + gpios = <&gpio0 4 GPIO_ACTIVE_LOW>; + }; + + power_green { + label = "wrc-1167ghbk2-s:green:power"; + gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; + }; + + power_blue { + label = "wrc-1167ghbk2-s:blue:power"; + gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>; + }; + + wps { + label = "wrc-1167ghbk2-s:red:wps"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; + }; + + power_red { + label = "wrc-1167ghbk2-s:red:power"; + gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <20>; + + reset { + label = "reset"; + gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&gpio0 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; +}; + +ðernet { + mtd-mac-address = <&factory 0xe000>; +}; + +&spi0 { + status = "okay"; + + m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <10000000>; + m25p,chunked-io = <32>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "u-boot-env"; + reg = <0x30000 0x10000>; + read-only; + }; + + factory: partition@40000 { + label = "factory"; + reg = <0x40000 0x10000>; + read-only; + }; + + partition@50000 { + label = "firmware"; + reg = <0x50000 0xf20000>; + }; + + partition@f70000 { + label = "user_data"; + reg = <0xf70000 0x80000>; + read-only; + }; + + partition@ff0000 { + label = "NVRAM"; + reg = <0xff0000 0x10000>; + read-only; + }; + }; +}; + +&pinctrl { + state_default: pinctrl0 { + gpio { + ralink,group = "i2c", "uart3", "jtag", "wdt"; + ralink,function = "gpio"; + }; + }; +}; + +&pcie { + status = "okay"; + // WRC-1167GHBK2-S has MT7615D for 2.4/5 GHz wifi, + // but it's not supported in OpenWrt. +}; + +&xhci { + status = "disabled"; +}; diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index f8fb28196b..f6f8ea065b 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -4,6 +4,18 @@ DEVICE_VARS += TPLINK_BOARD_ID TPLINK_HEADER_VERSION TPLINK_HWID TPLINK_HWREV +define Build/elecom-wrc-factory + $(eval product=$(word 1,$(1))) + $(eval version=$(word 2,$(1))) + $(STAGING_DIR_HOST)/bin/mkhash md5 $@ >> $@ + ( \ + echo -n "ELECOM $(product) v$(version)" | \ + dd bs=32 count=1 conv=sync; \ + dd if=$@; \ + ) > $@.new + mv $@.new $@ +endef + define Build/ubnt-erx-factory-image if [ -e $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) -a "$$(stat -c%s $@)" -lt "$(KERNEL_SIZE)" ]; then \ echo '21001:6' > $(1).compat; \ @@ -65,6 +77,16 @@ define Device/mediatek_ap-mt7621a-v60 endef TARGET_DEVICES += mediatek_ap-mt7621a-v60 +define Device/elecom_wrc-1167ghbk2-s + DTS := WRC-1167GHBK2-S + IMAGE_SIZE := 15488k + DEVICE_TITLE := ELECOM WRC-1167GHBK2-S + IMAGES += factory.bin + IMAGE/factory.bin := $$(sysupgrade_bin) | check-size $$$$(IMAGE_SIZE) |\ + elecom-wrc-factory WRC-1167GHBK2-S 0.00 +endef +TARGET_DEVICES += elecom_wrc-1167ghbk2-s + define Device/ew1200 DTS := EW1200 IMAGE_SIZE := $(ralink_default_fw_size_16M)