From: Stijn Tintel Date: Fri, 12 Apr 2019 17:21:58 +0000 (+0300) Subject: ath79: add support for Ubiquiti LiteBeam AC Gen2 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=157e17e985ea494f7f0a870df0afa0a837eccb8c;p=openwrt%2Fstaging%2Fwigyori.git ath79: add support for Ubiquiti LiteBeam AC Gen2 Hardware: * SoC: Atheros AR9342-BL1A * RAM: 64MB DDR2 (Winbond W9751G6KB-25) * Flash: 16MB SPI NOR (Macronix MX25L12835FZ2I-10G) * Ethernet: 1x 10/100/1000 Mbps (Atheros AR8035-A) with 24V PoE support * Wifi 2.4GHz: Atheros AR9340 v2 * WiFi 5GHz: Ubiquiti U-AME-G1-BR4A (rebranded QCA988X v2) * LEDs: 1x Power, 1x Ethernet * Buttons: 1x Reset * UART: 1x TTL 115200n8, 3.3V RX TX GND, 3.3V pin closest to RJ45 port The LEDs do not seem to be connected to any GPIO, so there is currently no way to control them. Installation via U-Boot, TFTP and serial console: * Configure your TFTP server with IP 192.168.1.254 * Connect serial console and power up the device * Hit any key to stop autoboot * tftpboot 0x81000000 openwrt-ath79-generic-ubnt_litebeam-ac-gen2-initramfs-kernel.bin * bootm 0x81000000 * copy openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin to /tmp * sysupgrade /tmp/openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin Signed-off-by: Stijn Tintel Acked-by: Petr Štetiar Acked-by: Adrian Schmutzler --- diff --git a/target/linux/ath79/dts/ar9342_ubnt_litebeam-ac-gen2.dts b/target/linux/ath79/dts/ar9342_ubnt_litebeam-ac-gen2.dts new file mode 100644 index 0000000000..d7eacf44d0 --- /dev/null +++ b/target/linux/ath79/dts/ar9342_ubnt_litebeam-ac-gen2.dts @@ -0,0 +1,39 @@ +// SPDX-License-Identifier: GPL-2.0 +/dts-v1/; + +#include +#include + +#include "ar9342_ubnt_wa.dtsi" + +/ { + compatible = "ubnt,litebeam-ac-gen2", "ubnt,wa", "qca,ar9342"; + model = "Ubiquiti LiteBeam AC Gen2"; +}; + +&mdio0 { + status = "okay"; + + phy-mask = <4>; + phy4: ethernet-phy@4 { + reg = <4>; + }; +}; + +ð0 { + status = "okay"; + + /* default for ar934x, except for 1000M and 10M */ + pll-data = <0x02000000 0x00000101 0x00001313>; + + mtd-mac-address = <&art 0x0>; + + phy-mode = "rgmii-id"; + phy-handle = <&phy4>; + + gmac-config { + device = <&gmac>; + rxd-delay = <3>; + rxdv-delay = <3>; + }; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 05ee1aa016..938213eadc 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -40,6 +40,7 @@ ath79_setup_interfaces() ubnt,bullet-m|\ ubnt,bullet-m-xw|\ ubnt,lap-120|\ + ubnt,litebeam-ac-gen2|\ ubnt,nanobeam-ac|\ ubnt,nanostation-ac-loco|\ ubnt,rocket-m|\ @@ -399,6 +400,9 @@ ath79_setup_macs() ubnt,unifi) label_mac=$(cat /sys/class/ieee80211/phy0/macaddress) ;; + ubnt,litebeam-ac-gen2) + label_mac=$(mtd_get_mac_binary art 0x5006) + ;; ubnt,routerstation|\ ubnt,routerstation-pro) wan_mac=$(fconfig -s -r -d $(find_mtd_part "RedBoot config") -n ar7100_esa) diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 062caf6ad5..55c6b74e74 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -17,6 +17,7 @@ case "$FIRMWARE" in ubnt,unifiac-mesh|\ ubnt,unifiac-mesh-pro|\ ubnt,lap-120|\ + ubnt,litebeam-ac-gen2|\ ubnt,nanobeam-ac|\ ubnt,nanostation-ac|\ ubnt,nanostation-ac-loco|\ diff --git a/target/linux/ath79/image/generic-ubnt.mk b/target/linux/ath79/image/generic-ubnt.mk index 9f55a89d27..e75b9ea770 100644 --- a/target/linux/ath79/image/generic-ubnt.mk +++ b/target/linux/ath79/image/generic-ubnt.mk @@ -127,6 +127,14 @@ define Device/ubnt_lap-120 endef TARGET_DEVICES += ubnt_lap-120 +define Device/ubnt_litebeam-ac-gen2 + $(Device/ubnt-wa) + DEVICE_MODEL := LiteBeam AC + DEVICE_VARIANT := Gen2 + DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct +endef +TARGET_DEVICES += ubnt_litebeam-ac-gen2 + define Device/ubnt_nanobeam-ac $(Device/ubnt-wa) DEVICE_MODEL := NanoBeam AC