From: Shiji Yang Date: Sun, 20 Mar 2022 15:42:37 +0000 (+0800) Subject: ramips: add support for H3C TX1800 Plus / TX1801 Plus / TX1806 X-Git-Tag: v23.05.0-rc1~2859 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=13308161788c98ae6cd48c22b13339fdb8c77130;p=openwrt%2Fopenwrt.git ramips: add support for H3C TX1800 Plus / TX1801 Plus / TX1806 H3C TX180x series WiFi6 routers are customized by different carrier. While these three devices look different, they use the same motherboard inside. Another minor difference comes from the model name definition in the u-boot environment variable. Specifications: SOC: MT7621 + MT7915 ROM: 128 MiB RAM: 256 MiB LED: status *2 Button: reset *1 + wps/mesh *1 Ethernet: lan *3 + wan *1 (10/100/1000Mbps) TTL Baudrate: 115200 TFTP server IP: 192.168.124.99 MAC Address: use address(sample 1) address(sample 2) source label 88:xx:xx:98:xx:12 88:xx:xx:a2:xx:a5 u-boot-env@ethaddr lan 88:xx:xx:98:xx:13 88:xx:xx:a2:xx:a6 $label +1 wan 88:xx:xx:98:xx:12 88:xx:xx:a2:xx:a5 $label WiFi4_2G 8a:xx:xx:58:xx:14 8a:xx:xx:52:xx:a7 (Compatibility mode) WiFi5_5G 8a:xx:xx:b8:xx:14 8a:xx:xx:b2:xx:a7 (Compatibility mode) WiFi6_2G 8a:xx:xx:18:xx:14 8a:xx:xx:12:xx:a7 WiFi6_5G 8a:xx:xx:78:xx:14 8a:xx:xx:72:xx:a7 Compatibility mode is used to guarantee the connection of old devices that only support WiFi4 or WiFi5. TFTP + TTL Installation: Although a TTL connection is required for installation, we do not need to tear down it. We can find the TTL port from the cooling hole at the bottom. It is located below LAN3 and the pins are defined as follows: |LAN1|LAN2|LAN3|----|WAN| -------------------- |GND|TX|RX|VCC| 1. Set tftp server IP to 192.168.124.99 and put initramfs firmware in server's root directory, rename it to a simple name "initramfs.bin". 2. Plug in the power supply and wait for power on, connect the TTL cable and open a TTL session, enter "reboot", then enter "Y" to confirm. Finally push "0" to interruput boot while booting. 3. Execute command to install a initramfs system: # tftp 0x80010000 192.168.124.99:initramfs.bin # bootm 0x80010000 4. Backup nand flash by OpenWrt LuCI or dd instruction. We need those partitions if we want to back to stock firmwre due to official website does not provide download link. # dd if=/dev/mtd1 of=/tmp/u-boot-env.bin # dd if=/dev/mtd4 of=/tmp/firmware.bin 5. Edit u-boot env to ensure use default bootargs and first image slot: # fw_setenv bootargs # fw_setenv bootflag 0 6. Upgrade sysupgrade firmware. 7. About restore stock firmware: flash the "firmware" and "u-boot-env" partitions that we backed up in step 4. # mtd write /tmp/u-boot-env.bin u-boot-env # mtd write /tmp/firmware.bin firmware Additional Info: The H3C stock firmware has a 160-byte firmware header that appears to use a non-standard CRC32 verification algorithm. For this part of the data, the u-boot does not check it so we can just directly replace it with a placeholder. Signed-off-by: Shiji Yang --- diff --git a/package/boot/uboot-envtools/files/ramips b/package/boot/uboot-envtools/files/ramips index 7514bf65fb..738d983af2 100644 --- a/package/boot/uboot-envtools/files/ramips +++ b/package/boot/uboot-envtools/files/ramips @@ -44,15 +44,18 @@ zbtlink,zbt-wg2626|\ zte,mf283plus) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x1000" "0x10000" ;; +h3c,tx1800-plus|\ +h3c,tx1801-plus|\ +h3c,tx1806|\ +jcg,q20) + ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000" + ;; hootoo,ht-tm05|\ ravpower,rp-wd03) idx="$(find_mtd_index u-boot-env)" [ -n "$idx" ] && \ ubootenv_add_uci_config "/dev/mtd$idx" "0x4000" "0x1000" "0x1000" ;; -jcg,q20) - ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000" - ;; beeline,smartbox-flash|\ linksys,ea6350-v4|\ linksys,ea7300-v1|\ diff --git a/target/linux/ramips/dts/mt7621_h3c_tx1800-plus.dts b/target/linux/ramips/dts/mt7621_h3c_tx1800-plus.dts new file mode 100644 index 0000000000..f763dd14dd --- /dev/null +++ b/target/linux/ramips/dts/mt7621_h3c_tx1800-plus.dts @@ -0,0 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7621_h3c_tx180x.dtsi" + +/ { + compatible = "h3c,tx1800-plus", "mediatek,mt7621-soc"; + model = "H3C TX1800 Plus"; +}; diff --git a/target/linux/ramips/dts/mt7621_h3c_tx1801-plus.dts b/target/linux/ramips/dts/mt7621_h3c_tx1801-plus.dts new file mode 100644 index 0000000000..4588b142c4 --- /dev/null +++ b/target/linux/ramips/dts/mt7621_h3c_tx1801-plus.dts @@ -0,0 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7621_h3c_tx180x.dtsi" + +/ { + compatible = "h3c,tx1801-plus", "mediatek,mt7621-soc"; + model = "H3C TX1801 Plus"; +}; diff --git a/target/linux/ramips/dts/mt7621_h3c_tx1806.dts b/target/linux/ramips/dts/mt7621_h3c_tx1806.dts new file mode 100644 index 0000000000..1e9b6456ee --- /dev/null +++ b/target/linux/ramips/dts/mt7621_h3c_tx1806.dts @@ -0,0 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7621_h3c_tx180x.dtsi" + +/ { + compatible = "h3c,tx1806", "mediatek,mt7621-soc"; + model = "H3C TX1806"; +}; diff --git a/target/linux/ramips/dts/mt7621_h3c_tx180x.dtsi b/target/linux/ramips/dts/mt7621_h3c_tx180x.dtsi new file mode 100644 index 0000000000..61f2f8cc98 --- /dev/null +++ b/target/linux/ramips/dts/mt7621_h3c_tx180x.dtsi @@ -0,0 +1,165 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7621.dtsi" + +#include +#include +#include + +/ { + aliases { + led-boot = &led_status_amber; + led-failsafe = &led_status_green; + led-running = &led_status_green; + led-upgrade = &led_status_amber; + }; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_status_amber: led-0 { + label = "amber:status"; + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + led_status_green: led-1 { + label = "green:status"; + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&gmac1 { + status = "okay"; + label = "wan"; + phy-handle = <ðphy4>; +}; + +&mdio { + ethphy4: ethernet-phy@4 { + reg = <4>; + }; +}; + +&nand { + status = "okay"; + + mediatek,nmbm; + mediatek,bmt-max-ratio = <1>; + mediatek,bmt-max-reserved-blocks = <64>; + mediatek,bmt-remap-range = <0x0000000 0x0a00000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x0080000>; + read-only; + }; + + partition@80000 { + label = "u-boot-env"; + reg = <0x0080000 0x0080000>; + }; + + partition@100000 { + label = "exp"; + reg = <0x0100000 0x0080000>; + read-only; + }; + + factory: partition@180000 { + label = "factory"; + reg = <0x0180000 0x0080000>; + read-only; + }; + + partition@200000 { + label = "firmware"; + reg = <0x0200000 0x7600000>; + + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "kernel"; + reg = <0x0000000 0x0800000>; + }; + + partition@800000 { + label = "ubi"; + reg = <0x0800000 0x6e00000>; + }; + }; + + /* last 8 MiB is reserved for NMBM bad block table */ + }; +}; + +&pcie { + status = "okay"; +}; + +&pcie1 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x0>; + mediatek,disable-radar-background; + }; +}; + +&pcie2 { + status = "disabled"; +}; + +&switch0 { + ports { + port@1 { + status = "okay"; + label = "lan1"; + }; + + port@2 { + status = "okay"; + label = "lan2"; + }; + + port@3 { + status = "okay"; + label = "lan3"; + }; + }; +}; + +&xhci { + status = "disabled"; +}; diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index 34eac32112..b560ce3d95 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -31,6 +31,12 @@ define Build/gemtek-trailer printf "%s%08X" ".GEMTEK." "$$(cksum $@ | cut -d ' ' -f1)" >> $@ endef +define Build/h3c-blank-header + dd if=/dev/zero of=$@.blank bs=160 count=1 + cat $@ >> $@.blank + mv $@.blank $@ +endef + define Build/iodata-factory $(eval fw_size=$(word 1,$(1))) $(eval fw_type=$(word 2,$(1))) @@ -752,6 +758,40 @@ define Device/gnubee_gb-pc2 endef TARGET_DEVICES += gnubee_gb-pc2 +define Device/h3c_tx180x + $(Device/dsa-migration) + BLOCKSIZE := 128k + PAGESIZE := 2048 + KERNEL_SIZE := 8192k + IMAGE_SIZE := 120832k + UBINIZE_OPTS := -E 5 + KERNEL_LOADADDR := 0x82000000 + KERNEL_INITRAMFS := kernel-bin | relocate-kernel 0x80001000 | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb + KERNEL := $$(KERNEL_INITRAMFS) | h3c-blank-header + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata + DEVICE_VENDOR := H3C + DEVICE_PACKAGES := kmod-mt7915e uboot-envtools +endef + +define Device/h3c_tx1800-plus + $(Device/h3c_tx180x) + DEVICE_MODEL := TX1800 Plus +endef +TARGET_DEVICES += h3c_tx1800-plus + +define Device/h3c_tx1801-plus + $(Device/h3c_tx180x) + DEVICE_MODEL := TX1801 Plus +endef +TARGET_DEVICES += h3c_tx1801-plus + +define Device/h3c_tx1806 + $(Device/h3c_tx180x) + DEVICE_MODEL := TX1806 +endef +TARGET_DEVICES += h3c_tx1806 + define Device/hilink_hlk-7621a-evb $(Device/dsa-migration) $(Device/uimage-lzma-loader) diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network index 320325f487..400b03133e 100644 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network @@ -28,6 +28,9 @@ ramips_setup_interfaces() ;; ampedwireless,ally-r1900k|\ gehua,ghl-r-001|\ + h3c,tx1800-plus|\ + h3c,tx1801-plus|\ + h3c,tx1806|\ hiwifi,hc5962|\ netgear,wax202|\ xiaomi,mi-router-3-pro|\ @@ -158,6 +161,13 @@ ramips_setup_macs() wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr) label_mac=$wan_mac ;; + h3c,tx1800-plus|\ + h3c,tx1801-plus|\ + h3c,tx1806) + label_mac=$(mtd_get_mac_ascii u-boot-env ethaddr) + lan_mac=$(macaddr_add "$label_mac" 1) + wan_mac=$label_mac + ;; hiwifi,hc5962) lan_mac=$(mtd_get_mac_ascii bdinfo "Vfac_mac ") label_mac=$lan_mac diff --git a/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac index bced044234..0ace1933e3 100644 --- a/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac +++ b/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac @@ -37,6 +37,13 @@ case "$board" in [ "$PHYNBR" = "1" ] && \ macaddr_add "$(mtd_get_mac_binary factory 0x4)" 1 > /sys${DEVPATH}/macaddress ;; + h3c,tx1800-plus|\ + h3c,tx1801-plus|\ + h3c,tx1806) + addr=$(macaddr_setbit $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) 2) 7) + [ "$PHYNBR" = "0" ] && echo -n ${addr:0:9}'1'${addr:10:7} > /sys${DEVPATH}/macaddress + [ "$PHYNBR" = "1" ] && echo -n ${addr:0:9}'7'${addr:10:7} > /sys${DEVPATH}/macaddress + ;; hiwifi,hc5962) label_mac=$(mtd_get_mac_ascii bdinfo "Vfac_mac ") [ "$PHYNBR" = "0" ] && [ -n "$label_mac" ] && \ diff --git a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh index 8a84130ab5..9af46202ba 100755 --- a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh @@ -60,6 +60,9 @@ platform_do_upgrade() { dlink,dir-2640-a1|\ dlink,dir-2660-a1|\ dlink,dir-853-a3|\ + h3c,tx1800-plus|\ + h3c,tx1801-plus|\ + h3c,tx1806|\ hiwifi,hc5962|\ iptime,a3004t|\ iptime,ax2004m|\