From: Sander Vanheule Date: Sat, 24 Jun 2023 20:18:35 +0000 (+0200) Subject: ramips: mt7621: add TP-Link EAP613 v1 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=11588c52b47c2c3b2cdc7849ce9e4804bfdb8bb5;p=openwrt%2Fstaging%2Fpepe2k.git ramips: mt7621: add TP-Link EAP613 v1 The TP-Link EAP613 v1 is a ceiling-mount 802.11ax access point. It can be powered via PoE or a DC barrel connector (12V). Connecting to the UART requires fine soldering and careful manipulation of any soldered wires. Device details: * SoC: MT7621AT * Flash: 16 MiB SPI NOR * RAM: 256 MiB DDR3L * Wi-Fi: * MT7905DA + MT7975D: 2.4 GHz + 5 GHz (DBDC), 2x2:2 * Two stamped metal antennas (ANT1, ANT2) * One PCB antenna (ANT3) * One unpopulated antenna (ANT4) * Ethernet: * 1× 10/100/1000 Mbps port with PoE * LEDs: * Array of four blue LEDs with one control line * Buttons: * Reset * Board test points: * UART: next to CPU RF-shield and power circuits * JTAG: under CPU RF-shield (untested) * Watchdog: 3PEAK TPV706 (not implemented) Althought three antennas are populated, the MT7905DA does not support the additional Rx chain for background DFS detection (or Bluetooth) according to commit 6cbcc34f50a3 ("ramips: disable unsupported background radar detection"). MAC addresses: * LAN: 48:22:54:xx:xx:a2 (device label) * WLAN 2.4 GHz: 48:22:54:xx:xx:a2 * WLAN 5 GHz: 48:22:54:xx:xx:a3 The radio calibration blob stored in flash also contains valid MAC addresses for both radio bands (OUI 00:0c:43). Factory install: 1. Enable SSH on the device via web interface 2. Log in with SSH, and run `cliclientd stopcs` 3. Upload -factory.bin image via web interface. It may be necessary to shorten the filename of the image to e.g. 'factory.bin'. Recovery: 1. Open the device by unscrewing four screws from the backside 2. Carefully remove board from the housing 3. Connect to UART (3.3V): * Find test points labelled "VCC", "GND", "UART_TX", "UART_RX" * Solder wires to test points or connect otherwise. Be careful not to damage the PCB e.g. by pulling on soldered wires. * Open console with 115200n8 settings 4. Interrupt bootloader and use tftpboot to start an initramfs: setenv ipaddr $DEVICE_IP setenv serverip $SERVER_IP tftpboot 84000000 openwrt-initramfs-kernel.bin bootm DO NOT use saveenv to store modified u-boot environment variables. The environment is saved at flash offset 0x30000, which erases part of the (secondary) bootloader. The device uses two bootloader stages. The first stage will load the second stage from a uImage stored at flash offset 0x10000. In case of a damaged second stage, the first stage should allow uploading a new image via y-modem (untested). Signed-off-by: Sander Vanheule --- diff --git a/target/linux/ramips/dts/mt7621_tplink_eap613-v1.dts b/target/linux/ramips/dts/mt7621_tplink_eap613-v1.dts new file mode 100644 index 0000000000..d25bf57560 --- /dev/null +++ b/target/linux/ramips/dts/mt7621_tplink_eap613-v1.dts @@ -0,0 +1,151 @@ +// SPDX-License-Identifier: GPL-2.0-or-later + +#include "mt7621.dtsi" + +#include +#include +#include + +/ { + compatible = "tplink,eap613-v1", "mediatek,mt7621-soc"; + model = "TP-Link EAP613 v1"; + + aliases { + label-mac-device = &gmac0; + led-boot = &led_status; + led-failsafe = &led_status; + led-running = &led_status; + led-upgrade = &led_status; + }; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + leds { + compatible = "gpio-leds"; + + led_status: status { + label = "blue:status"; + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&gpio 7 GPIO_ACTIVE_HIGH>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <20000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x80000>; + read-only; + }; + + partition@80000 { + label = "partition-table"; + reg = <0x80000 0x10000>; + read-only; + }; + + partition@90000 { + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + label = "product-info"; + reg = <0x90000 0x10000>; + read-only; + + macaddr: macaddr@8 { + reg = <0x8 0x6>; + }; + }; + + partition@a0000 { + compatible = "denx,fit"; + label = "firmware"; + reg = <0xa0000 0xcf0000>; + }; + + partition@d90000 { + label = "user-config"; + reg = <0xd90000 0x60000>; + read-only; + }; + + partition@f30000 { + label = "mutil-log"; + reg = <0xf30000 0x80000>; + read-only; + }; + + partition@fb0000 { + label = "oops"; + reg = <0xfb0000 0x40000>; + read-only; + }; + + radio: partition@ff0000 { + label = "radio"; + reg = <0xff0000 0x10000>; + read-only; + }; + }; + }; +}; + +&state_default { + gpio { + groups = "uart3"; + function = "gpio"; + }; +}; + +&pcie { + status = "okay"; +}; + +&pcie1 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&radio 0x0>; + mediatek,disable-radar-background; + }; +}; + +&gmac0 { + nvmem-cells = <&macaddr>; + nvmem-cell-names = "mac-address"; +}; + +&switch0 { + ports { + port@0 { + status = "okay"; + label = "lan"; + }; + }; +}; diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index 92053e087c..0d25fc1eb3 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -2172,6 +2172,19 @@ define Device/tplink_eap235-wall-v1 endef TARGET_DEVICES += tplink_eap235-wall-v1 +define Device/tplink_eap613-v1 + $(Device/dsa-migration) + $(Device/tplink-safeloader) + DEVICE_MODEL := EAP613 + DEVICE_VARIANT := v1 + DEVICE_PACKAGES := kmod-mt7915-firmware -uboot-envtools + TPLINK_BOARD_ID := EAP610-V3 + KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | pad-to 64k + KERNEL_INITRAMFS := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd + IMAGE_SIZE := 13248k +endef +TARGET_DEVICES += tplink_eap613-v1 + define Device/tplink_eap615-wall-v1 $(Device/dsa-migration) $(Device/tplink-safeloader) diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network index a5671af82f..38655ef746 100644 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network @@ -25,6 +25,7 @@ ramips_setup_interfaces() sercomm,na502|\ sercomm,na502s|\ thunder,timecloud|\ + tplink,eap613-v1|\ tplink,re350-v1|\ tplink,re500-v1|\ tplink,re650-v1|\ diff --git a/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac index 351aa396e9..a15b4a225f 100644 --- a/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac +++ b/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac @@ -167,6 +167,7 @@ case "$board" in hw_mac_addr="$(mtd_get_mac_binary factory 0x4)" [ "$PHYNBR" = "1" ] && macaddr_add $hw_mac_addr 4 > /sys${DEVPATH}/macaddress ;; + tplink,eap613-v1|\ tplink,eap615-wall-v1) hw_mac_addr="$(mtd_get_mac_binary product-info 0x8)" macaddr_add "$hw_mac_addr" "$PHYNBR" > "/sys${DEVPATH}/macaddress"