From: Daniel Golle Date: Tue, 20 Aug 2024 16:20:29 +0000 (+0100) Subject: mediatek: backport pending Ethernet PHY driver patches X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=1069514978c419cc5bdfc18c5670b46d0443a686;p=openwrt%2Fstaging%2Fthess.git mediatek: backport pending Ethernet PHY driver patches Use pending patchset for 2.5GE PHY driver, unifying LED handling accross all MediaTek Ethernet PHYs. Signed-off-by: Daniel Golle --- diff --git a/target/linux/mediatek/files-6.6/arch/arm64/boot/dts/mediatek/mt7988a.dtsi b/target/linux/mediatek/files-6.6/arch/arm64/boot/dts/mediatek/mt7988a.dtsi index 9ad068fe05..6a15dcff3d 100644 --- a/target/linux/mediatek/files-6.6/arch/arm64/boot/dts/mediatek/mt7988a.dtsi +++ b/target/linux/mediatek/files-6.6/arch/arm64/boot/dts/mediatek/mt7988a.dtsi @@ -1490,6 +1490,23 @@ compatible = "ethernet-phy-ieee802.3-c45"; reg = <15>; phy-mode = "internal"; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + i2p5gbe_led0: i2p5gbe-led0@0 { + reg = <0>; + function = LED_FUNCTION_LAN; + status = "disabled"; + }; + + i2p5gbe_led1: i2p5gbe-led1@1 { + reg = <1>; + function = LED_FUNCTION_LAN; + status = "disabled"; + }; + }; }; }; }; diff --git a/target/linux/mediatek/files-6.6/drivers/net/phy/mediatek-2p5ge.c b/target/linux/mediatek/files-6.6/drivers/net/phy/mediatek-2p5ge.c deleted file mode 100644 index d1d01190ed..0000000000 --- a/target/linux/mediatek/files-6.6/drivers/net/phy/mediatek-2p5ge.c +++ /dev/null @@ -1,321 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#define MT7988_2P5GE_PMB "mediatek/mt7988/i2p5ge-phy-pmb.bin" - -#define MD32_EN BIT(0) -#define PMEM_PRIORITY BIT(8) -#define DMEM_PRIORITY BIT(16) - -#define BASE100T_STATUS_EXTEND 0x10 -#define BASE1000T_STATUS_EXTEND 0x11 -#define EXTEND_CTRL_AND_STATUS 0x16 - -#define PHY_AUX_CTRL_STATUS 0x1d -#define PHY_AUX_DPX_MASK GENMASK(5, 5) -#define PHY_AUX_SPEED_MASK GENMASK(4, 2) - -/* Registers on MDIO_MMD_VEND1 */ -#define MTK_PHY_LINK_STATUS_MISC 0xa2 -#define MTK_PHY_FDX_ENABLE BIT(5) - -#define MTK_PHY_LPI_PCS_DSP_CTRL 0x121 -#define MTK_PHY_LPI_SIG_EN_LO_THRESH100_MASK GENMASK(12, 8) - -/* Registers on MDIO_MMD_VEND2 */ -#define MTK_PHY_LED0_ON_CTRL 0x24 -#define MTK_PHY_LED0_ON_LINK1000 BIT(0) -#define MTK_PHY_LED0_ON_LINK100 BIT(1) -#define MTK_PHY_LED0_ON_LINK10 BIT(2) -#define MTK_PHY_LED0_ON_LINK2500 BIT(7) -#define MTK_PHY_LED0_POLARITY BIT(14) - -#define MTK_PHY_LED1_ON_CTRL 0x26 -#define MTK_PHY_LED1_ON_FDX BIT(4) -#define MTK_PHY_LED1_ON_HDX BIT(5) -#define MTK_PHY_LED1_POLARITY BIT(14) - -#define MTK_EXT_PAGE_ACCESS 0x1f -#define MTK_PHY_PAGE_STANDARD 0x0000 -#define MTK_PHY_PAGE_EXTENDED_52B5 0x52b5 - -struct mtk_i2p5ge_phy_priv { - bool fw_loaded; -}; - -enum { - PHY_AUX_SPD_10 = 0, - PHY_AUX_SPD_100, - PHY_AUX_SPD_1000, - PHY_AUX_SPD_2500, -}; - -static int mtk_2p5ge_phy_read_page(struct phy_device *phydev) -{ - return __phy_read(phydev, MTK_EXT_PAGE_ACCESS); -} - -static int mtk_2p5ge_phy_write_page(struct phy_device *phydev, int page) -{ - return __phy_write(phydev, MTK_EXT_PAGE_ACCESS, page); -} - -static int mt7988_2p5ge_phy_probe(struct phy_device *phydev) -{ - struct mtk_i2p5ge_phy_priv *phy_priv; - - phy_priv = devm_kzalloc(&phydev->mdio.dev, - sizeof(struct mtk_i2p5ge_phy_priv), GFP_KERNEL); - if (!phy_priv) - return -ENOMEM; - - phydev->priv = phy_priv; - - return 0; -} - -static int mt7988_2p5ge_phy_config_init(struct phy_device *phydev) -{ - int ret, i; - const struct firmware *fw; - struct device *dev = &phydev->mdio.dev; - struct device_node *np; - void __iomem *pmb_addr; - void __iomem *md32_en_cfg_base; - struct mtk_i2p5ge_phy_priv *phy_priv = phydev->priv; - u16 reg; - struct pinctrl *pinctrl; - - if (!phy_priv->fw_loaded) { - np = of_find_compatible_node(NULL, NULL, "mediatek,2p5gphy-fw"); - if (!np) - return -ENOENT; - pmb_addr = of_iomap(np, 0); - if (!pmb_addr) - return -ENOMEM; - md32_en_cfg_base = of_iomap(np, 1); - if (!md32_en_cfg_base) - return -ENOMEM; - - ret = request_firmware(&fw, MT7988_2P5GE_PMB, dev); - if (ret) { - dev_err(dev, "failed to load firmware: %s, ret: %d\n", - MT7988_2P5GE_PMB, ret); - return ret; - } - - reg = readw(md32_en_cfg_base); - if (reg & MD32_EN) { - phy_set_bits(phydev, 0, BIT(15)); - usleep_range(10000, 11000); - } - phy_set_bits(phydev, 0, BIT(11)); - - /* Write magic number to safely stall MCU */ - phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x800e, 0x1100); - phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x800f, 0x00df); - - for (i = 0; i < fw->size - 1; i += 4) - writel(*((uint32_t *)(fw->data + i)), pmb_addr + i); - release_firmware(fw); - - writew(reg & ~MD32_EN, md32_en_cfg_base); - writew(reg | MD32_EN, md32_en_cfg_base); - phy_set_bits(phydev, 0, BIT(15)); - dev_info(dev, "Firmware loading/trigger ok.\n"); - - phy_priv->fw_loaded = true; - } - - /* Setup LED */ - - /* Set polarity of led0 to active-high for BPI-R4 */ - phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED0_ON_CTRL, - MTK_PHY_LED0_POLARITY); - - phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED0_ON_CTRL, - MTK_PHY_LED0_ON_LINK10 | - MTK_PHY_LED0_ON_LINK100 | - MTK_PHY_LED0_ON_LINK1000 | - MTK_PHY_LED0_ON_LINK2500); - phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED1_ON_CTRL, - MTK_PHY_LED1_ON_FDX | MTK_PHY_LED1_ON_HDX); - - pinctrl = devm_pinctrl_get_select(&phydev->mdio.dev, "i2p5gbe-led"); - if (IS_ERR(pinctrl)) { - dev_err(&phydev->mdio.dev, "Fail to set LED pins!\n"); - return PTR_ERR(pinctrl); - } - - phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_LPI_PCS_DSP_CTRL, - MTK_PHY_LPI_SIG_EN_LO_THRESH100_MASK, 0); - - /* Enable 16-bit next page exchange bit if 1000-BT isn't advertizing */ - phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); - __phy_write(phydev, 0x11, 0xfbfa); - __phy_write(phydev, 0x12, 0xc3); - __phy_write(phydev, 0x10, 0x87f8); - phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); - - return 0; -} - -static int mt7988_2p5ge_phy_config_aneg(struct phy_device *phydev) -{ - bool changed = false; - u32 adv; - int ret; - - if (phydev->autoneg == AUTONEG_DISABLE) { - /* Configure half duplex with genphy_setup_forced, - * because genphy_c45_pma_setup_forced does not support. - */ - return phydev->duplex != DUPLEX_FULL - ? genphy_setup_forced(phydev) - : genphy_c45_pma_setup_forced(phydev); - } - - ret = genphy_c45_an_config_aneg(phydev); - if (ret < 0) - return ret; - if (ret > 0) - changed = true; - - adv = linkmode_adv_to_mii_ctrl1000_t(phydev->advertising); - ret = phy_modify_changed(phydev, MII_CTRL1000, - ADVERTISE_1000FULL | ADVERTISE_1000HALF, - adv); - if (ret < 0) - return ret; - if (ret > 0) - changed = true; - - return genphy_c45_check_and_restart_aneg(phydev, changed); -} - -static int mt7988_2p5ge_phy_get_features(struct phy_device *phydev) -{ - int ret; - - ret = genphy_read_abilities(phydev); - if (ret) - return ret; - - /* We don't support HDX at MAC layer on mt7988. - * So mask phy's HDX capabilities, too. - */ - linkmode_set_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT, - phydev->supported); - linkmode_set_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT, - phydev->supported); - linkmode_set_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT, - phydev->supported); - linkmode_set_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, - phydev->supported); - linkmode_set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, phydev->supported); - - return 0; -} - -static int mt7988_2p5ge_phy_read_status(struct phy_device *phydev) -{ - int ret; - - ret = genphy_update_link(phydev); - if (ret) - return ret; - - phydev->speed = SPEED_UNKNOWN; - phydev->duplex = DUPLEX_UNKNOWN; - phydev->pause = 0; - phydev->asym_pause = 0; - - if (phydev->autoneg == AUTONEG_ENABLE && phydev->autoneg_complete) { - ret = genphy_c45_read_lpa(phydev); - if (ret < 0) - return ret; - - /* Read the link partner's 1G advertisement */ - ret = phy_read(phydev, MII_STAT1000); - if (ret < 0) - return ret; - mii_stat1000_mod_linkmode_lpa_t(phydev->lp_advertising, ret); - } else if (phydev->autoneg == AUTONEG_DISABLE) { - linkmode_zero(phydev->lp_advertising); - } - - ret = phy_read(phydev, PHY_AUX_CTRL_STATUS); - if (ret < 0) - return ret; - - switch (FIELD_GET(PHY_AUX_SPEED_MASK, ret)) { - case PHY_AUX_SPD_10: - phydev->speed = SPEED_10; - break; - case PHY_AUX_SPD_100: - phydev->speed = SPEED_100; - break; - case PHY_AUX_SPD_1000: - phydev->speed = SPEED_1000; - break; - case PHY_AUX_SPD_2500: - phydev->speed = SPEED_2500; - break; - } - - ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_LINK_STATUS_MISC); - if (ret < 0) - return ret; - - phydev->duplex = (ret & MTK_PHY_FDX_ENABLE) ? DUPLEX_FULL : DUPLEX_HALF; - /* FIXME: The current firmware always enables rate adaptation mode. */ - phydev->rate_matching = RATE_MATCH_PAUSE; - - return 0; -} - -static int mt7988_2p5ge_phy_get_rate_matching(struct phy_device *phydev, - phy_interface_t iface) -{ - return RATE_MATCH_PAUSE; -} - -static struct phy_driver mtk_gephy_driver[] = { - { - PHY_ID_MATCH_MODEL(0x00339c11), - .name = "MediaTek MT798x 2.5GbE PHY", - .probe = mt7988_2p5ge_phy_probe, - .config_init = mt7988_2p5ge_phy_config_init, - .config_aneg = mt7988_2p5ge_phy_config_aneg, - .get_features = mt7988_2p5ge_phy_get_features, - .read_status = mt7988_2p5ge_phy_read_status, - .get_rate_matching = mt7988_2p5ge_phy_get_rate_matching, - .suspend = genphy_suspend, - .resume = genphy_resume, - .read_page = mtk_2p5ge_phy_read_page, - .write_page = mtk_2p5ge_phy_write_page, - }, -}; - -module_phy_driver(mtk_gephy_driver); - -static struct mdio_device_id __maybe_unused mtk_2p5ge_phy_tbl[] = { - { PHY_ID_MATCH_VENDOR(0x00339c00) }, - { } -}; - -MODULE_DESCRIPTION("MediaTek 2.5Gb Ethernet PHY driver"); -MODULE_AUTHOR("SkyLake Huang "); -MODULE_LICENSE("GPL"); - -MODULE_DEVICE_TABLE(mdio, mtk_2p5ge_phy_tbl); -MODULE_FIRMWARE(MT7988_2P5GE_PMB); diff --git a/target/linux/mediatek/filogic/config-6.6 b/target/linux/mediatek/filogic/config-6.6 index 6d9d42853b..cb36d74e1d 100644 --- a/target/linux/mediatek/filogic/config-6.6 +++ b/target/linux/mediatek/filogic/config-6.6 @@ -240,7 +240,7 @@ CONFIG_MAXLINEAR_GPHY=y CONFIG_MDIO_BUS=y CONFIG_MDIO_DEVICE=y CONFIG_MDIO_DEVRES=y -CONFIG_MEDIATEK_2P5G_PHY=y +CONFIG_MEDIATEK_2P5GE_PHY=y CONFIG_MEDIATEK_GE_PHY=y CONFIG_MEDIATEK_GE_SOC_PHY=y CONFIG_MEDIATEK_WATCHDOG=y diff --git a/target/linux/mediatek/patches-6.6/733-01-net-phy-mediatek-Re-organize-MediaTek-ethernet-phy-d.patch b/target/linux/mediatek/patches-6.6/733-01-net-phy-mediatek-Re-organize-MediaTek-ethernet-phy-d.patch new file mode 100644 index 0000000000..3ec756bb4b --- /dev/null +++ b/target/linux/mediatek/patches-6.6/733-01-net-phy-mediatek-Re-organize-MediaTek-ethernet-phy-d.patch @@ -0,0 +1,3513 @@ +From c14e7c954fd752fbb3da17a8bcf65cd9dbf41186 Mon Sep 17 00:00:00 2001 +From: "SkyLake.Huang" +Date: Mon, 1 Jul 2024 18:54:05 +0800 +Subject: [PATCH 01/13] net: phy: mediatek: Re-organize MediaTek ethernet phy + drivers + +Re-organize MediaTek ethernet phy driver files and get ready to integrate +some common functions and add new 2.5G phy driver. +mtk-ge.c: MT7530 Gphy on MT7621 & MT7531 Gphy +mtk-ge-soc.c: Built-in Gphy on MT7981 & Built-in switch Gphy on MT7988 +mtk-2p5ge.c: Planned for built-in 2.5G phy on MT7988 + +Signed-off-by: SkyLake.Huang +--- + drivers/net/phy/Kconfig | 17 +------------- + drivers/net/phy/Makefile | 3 +-- + drivers/net/phy/mediatek/Kconfig | 22 +++++++++++++++++++ + drivers/net/phy/mediatek/Makefile | 3 +++ + .../mtk-ge-soc.c} | 0 + .../phy/{mediatek-ge.c => mediatek/mtk-ge.c} | 0 + 7 files changed, 29 insertions(+), 20 deletions(-) + create mode 100644 drivers/net/phy/mediatek/Kconfig + create mode 100644 drivers/net/phy/mediatek/Makefile + rename drivers/net/phy/{mediatek-ge-soc.c => mediatek/mtk-ge-soc.c} (100%) + rename drivers/net/phy/{mediatek-ge.c => mediatek/mtk-ge.c} (100%) + +--- a/drivers/net/phy/Kconfig ++++ b/drivers/net/phy/Kconfig +@@ -313,22 +313,7 @@ config MAXLINEAR_GPHY + Support for the Maxlinear GPY115, GPY211, GPY212, GPY215, + GPY241, GPY245 PHYs. + +-config MEDIATEK_GE_PHY +- tristate "MediaTek Gigabit Ethernet PHYs" +- help +- Supports the MediaTek Gigabit Ethernet PHYs. +- +-config MEDIATEK_GE_SOC_PHY +- tristate "MediaTek SoC Ethernet PHYs" +- depends on (ARM64 && ARCH_MEDIATEK) || COMPILE_TEST +- depends on NVMEM_MTK_EFUSE +- help +- Supports MediaTek SoC built-in Gigabit Ethernet PHYs. +- +- Include support for built-in Ethernet PHYs which are present in +- the MT7981 and MT7988 SoCs. These PHYs need calibration data +- present in the SoCs efuse and will dynamically calibrate VCM +- (common-mode voltage) during startup. ++source "drivers/net/phy/mediatek/Kconfig" + + config MICREL_PHY + tristate "Micrel PHYs" +--- a/drivers/net/phy/Makefile ++++ b/drivers/net/phy/Makefile +@@ -82,8 +82,7 @@ obj-$(CONFIG_MARVELL_PHY) += marvell.o + obj-$(CONFIG_MARVELL_88Q2XXX_PHY) += marvell-88q2xxx.o + obj-$(CONFIG_MARVELL_88X2222_PHY) += marvell-88x2222.o + obj-$(CONFIG_MAXLINEAR_GPHY) += mxl-gpy.o +-obj-$(CONFIG_MEDIATEK_GE_PHY) += mediatek-ge.o +-obj-$(CONFIG_MEDIATEK_GE_SOC_PHY) += mediatek-ge-soc.o ++obj-y += mediatek/ + obj-$(CONFIG_MESON_GXL_PHY) += meson-gxl.o + obj-$(CONFIG_MICREL_KS8995MA) += spi_ks8995.o + obj-$(CONFIG_MICREL_PHY) += micrel.o +--- /dev/null ++++ b/drivers/net/phy/mediatek/Kconfig +@@ -0,0 +1,22 @@ ++# SPDX-License-Identifier: GPL-2.0-only ++config MEDIATEK_GE_PHY ++ tristate "MediaTek Gigabit Ethernet PHYs" ++ help ++ Supports the MediaTek non-built-in Gigabit Ethernet PHYs. ++ ++ Non-built-in Gigabit Ethernet PHYs include mt7530/mt7531. ++ You may find mt7530 inside mt7621. This driver shares some ++ common operations with MediaTek SoC built-in Gigabit ++ Ethernet PHYs. ++ ++config MEDIATEK_GE_SOC_PHY ++ tristate "MediaTek SoC Ethernet PHYs" ++ depends on (ARM64 && ARCH_MEDIATEK) || COMPILE_TEST ++ select NVMEM_MTK_EFUSE ++ help ++ Supports MediaTek SoC built-in Gigabit Ethernet PHYs. ++ ++ Include support for built-in Ethernet PHYs which are present in ++ the MT7981 and MT7988 SoCs. These PHYs need calibration data ++ present in the SoCs efuse and will dynamically calibrate VCM ++ (common-mode voltage) during startup. +--- /dev/null ++++ b/drivers/net/phy/mediatek/Makefile +@@ -0,0 +1,3 @@ ++# SPDX-License-Identifier: GPL-2.0 ++obj-$(CONFIG_MEDIATEK_GE_PHY) += mtk-ge.o ++obj-$(CONFIG_MEDIATEK_GE_SOC_PHY) += mtk-ge-soc.o +--- a/drivers/net/phy/mediatek-ge-soc.c ++++ /dev/null +@@ -1,1555 +0,0 @@ +-// SPDX-License-Identifier: GPL-2.0+ +-#include +-#include +-#include +-#include +-#include +-#include +-#include +-#include +- +-#define MTK_GPHY_ID_MT7981 0x03a29461 +-#define MTK_GPHY_ID_MT7988 0x03a29481 +- +-#define MTK_EXT_PAGE_ACCESS 0x1f +-#define MTK_PHY_PAGE_STANDARD 0x0000 +-#define MTK_PHY_PAGE_EXTENDED_3 0x0003 +- +-#define MTK_PHY_LPI_REG_14 0x14 +-#define MTK_PHY_LPI_WAKE_TIMER_1000_MASK GENMASK(8, 0) +- +-#define MTK_PHY_LPI_REG_1c 0x1c +-#define MTK_PHY_SMI_DET_ON_THRESH_MASK GENMASK(13, 8) +- +-#define MTK_PHY_PAGE_EXTENDED_2A30 0x2a30 +-#define MTK_PHY_PAGE_EXTENDED_52B5 0x52b5 +- +-#define ANALOG_INTERNAL_OPERATION_MAX_US 20 +-#define TXRESERVE_MIN 0 +-#define TXRESERVE_MAX 7 +- +-#define MTK_PHY_ANARG_RG 0x10 +-#define MTK_PHY_TCLKOFFSET_MASK GENMASK(12, 8) +- +-/* Registers on MDIO_MMD_VEND1 */ +-#define MTK_PHY_TXVLD_DA_RG 0x12 +-#define MTK_PHY_DA_TX_I2MPB_A_GBE_MASK GENMASK(15, 10) +-#define MTK_PHY_DA_TX_I2MPB_A_TBT_MASK GENMASK(5, 0) +- +-#define MTK_PHY_TX_I2MPB_TEST_MODE_A2 0x16 +-#define MTK_PHY_DA_TX_I2MPB_A_HBT_MASK GENMASK(15, 10) +-#define MTK_PHY_DA_TX_I2MPB_A_TST_MASK GENMASK(5, 0) +- +-#define MTK_PHY_TX_I2MPB_TEST_MODE_B1 0x17 +-#define MTK_PHY_DA_TX_I2MPB_B_GBE_MASK GENMASK(13, 8) +-#define MTK_PHY_DA_TX_I2MPB_B_TBT_MASK GENMASK(5, 0) +- +-#define MTK_PHY_TX_I2MPB_TEST_MODE_B2 0x18 +-#define MTK_PHY_DA_TX_I2MPB_B_HBT_MASK GENMASK(13, 8) +-#define MTK_PHY_DA_TX_I2MPB_B_TST_MASK GENMASK(5, 0) +- +-#define MTK_PHY_TX_I2MPB_TEST_MODE_C1 0x19 +-#define MTK_PHY_DA_TX_I2MPB_C_GBE_MASK GENMASK(13, 8) +-#define MTK_PHY_DA_TX_I2MPB_C_TBT_MASK GENMASK(5, 0) +- +-#define MTK_PHY_TX_I2MPB_TEST_MODE_C2 0x20 +-#define MTK_PHY_DA_TX_I2MPB_C_HBT_MASK GENMASK(13, 8) +-#define MTK_PHY_DA_TX_I2MPB_C_TST_MASK GENMASK(5, 0) +- +-#define MTK_PHY_TX_I2MPB_TEST_MODE_D1 0x21 +-#define MTK_PHY_DA_TX_I2MPB_D_GBE_MASK GENMASK(13, 8) +-#define MTK_PHY_DA_TX_I2MPB_D_TBT_MASK GENMASK(5, 0) +- +-#define MTK_PHY_TX_I2MPB_TEST_MODE_D2 0x22 +-#define MTK_PHY_DA_TX_I2MPB_D_HBT_MASK GENMASK(13, 8) +-#define MTK_PHY_DA_TX_I2MPB_D_TST_MASK GENMASK(5, 0) +- +-#define MTK_PHY_RXADC_CTRL_RG7 0xc6 +-#define MTK_PHY_DA_AD_BUF_BIAS_LP_MASK GENMASK(9, 8) +- +-#define MTK_PHY_RXADC_CTRL_RG9 0xc8 +-#define MTK_PHY_DA_RX_PSBN_TBT_MASK GENMASK(14, 12) +-#define MTK_PHY_DA_RX_PSBN_HBT_MASK GENMASK(10, 8) +-#define MTK_PHY_DA_RX_PSBN_GBE_MASK GENMASK(6, 4) +-#define MTK_PHY_DA_RX_PSBN_LP_MASK GENMASK(2, 0) +- +-#define MTK_PHY_LDO_OUTPUT_V 0xd7 +- +-#define MTK_PHY_RG_ANA_CAL_RG0 0xdb +-#define MTK_PHY_RG_CAL_CKINV BIT(12) +-#define MTK_PHY_RG_ANA_CALEN BIT(8) +-#define MTK_PHY_RG_ZCALEN_A BIT(0) +- +-#define MTK_PHY_RG_ANA_CAL_RG1 0xdc +-#define MTK_PHY_RG_ZCALEN_B BIT(12) +-#define MTK_PHY_RG_ZCALEN_C BIT(8) +-#define MTK_PHY_RG_ZCALEN_D BIT(4) +-#define MTK_PHY_RG_TXVOS_CALEN BIT(0) +- +-#define MTK_PHY_RG_ANA_CAL_RG5 0xe0 +-#define MTK_PHY_RG_REXT_TRIM_MASK GENMASK(13, 8) +- +-#define MTK_PHY_RG_TX_FILTER 0xfe +- +-#define MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG120 0x120 +-#define MTK_PHY_LPI_SIG_EN_LO_THRESH1000_MASK GENMASK(12, 8) +-#define MTK_PHY_LPI_SIG_EN_HI_THRESH1000_MASK GENMASK(4, 0) +- +-#define MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG122 0x122 +-#define MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK GENMASK(7, 0) +- +-#define MTK_PHY_RG_TESTMUX_ADC_CTRL 0x144 +-#define MTK_PHY_RG_TXEN_DIG_MASK GENMASK(5, 5) +- +-#define MTK_PHY_RG_CR_TX_AMP_OFFSET_A_B 0x172 +-#define MTK_PHY_CR_TX_AMP_OFFSET_A_MASK GENMASK(13, 8) +-#define MTK_PHY_CR_TX_AMP_OFFSET_B_MASK GENMASK(6, 0) +- +-#define MTK_PHY_RG_CR_TX_AMP_OFFSET_C_D 0x173 +-#define MTK_PHY_CR_TX_AMP_OFFSET_C_MASK GENMASK(13, 8) +-#define MTK_PHY_CR_TX_AMP_OFFSET_D_MASK GENMASK(6, 0) +- +-#define MTK_PHY_RG_AD_CAL_COMP 0x17a +-#define MTK_PHY_AD_CAL_COMP_OUT_SHIFT (8) +- +-#define MTK_PHY_RG_AD_CAL_CLK 0x17b +-#define MTK_PHY_DA_CAL_CLK BIT(0) +- +-#define MTK_PHY_RG_AD_CALIN 0x17c +-#define MTK_PHY_DA_CALIN_FLAG BIT(0) +- +-#define MTK_PHY_RG_DASN_DAC_IN0_A 0x17d +-#define MTK_PHY_DASN_DAC_IN0_A_MASK GENMASK(9, 0) +- +-#define MTK_PHY_RG_DASN_DAC_IN0_B 0x17e +-#define MTK_PHY_DASN_DAC_IN0_B_MASK GENMASK(9, 0) +- +-#define MTK_PHY_RG_DASN_DAC_IN0_C 0x17f +-#define MTK_PHY_DASN_DAC_IN0_C_MASK GENMASK(9, 0) +- +-#define MTK_PHY_RG_DASN_DAC_IN0_D 0x180 +-#define MTK_PHY_DASN_DAC_IN0_D_MASK GENMASK(9, 0) +- +-#define MTK_PHY_RG_DASN_DAC_IN1_A 0x181 +-#define MTK_PHY_DASN_DAC_IN1_A_MASK GENMASK(9, 0) +- +-#define MTK_PHY_RG_DASN_DAC_IN1_B 0x182 +-#define MTK_PHY_DASN_DAC_IN1_B_MASK GENMASK(9, 0) +- +-#define MTK_PHY_RG_DASN_DAC_IN1_C 0x183 +-#define MTK_PHY_DASN_DAC_IN1_C_MASK GENMASK(9, 0) +- +-#define MTK_PHY_RG_DASN_DAC_IN1_D 0x184 +-#define MTK_PHY_DASN_DAC_IN1_D_MASK GENMASK(9, 0) +- +-#define MTK_PHY_RG_DEV1E_REG19b 0x19b +-#define MTK_PHY_BYPASS_DSP_LPI_READY BIT(8) +- +-#define MTK_PHY_RG_LP_IIR2_K1_L 0x22a +-#define MTK_PHY_RG_LP_IIR2_K1_U 0x22b +-#define MTK_PHY_RG_LP_IIR2_K2_L 0x22c +-#define MTK_PHY_RG_LP_IIR2_K2_U 0x22d +-#define MTK_PHY_RG_LP_IIR2_K3_L 0x22e +-#define MTK_PHY_RG_LP_IIR2_K3_U 0x22f +-#define MTK_PHY_RG_LP_IIR2_K4_L 0x230 +-#define MTK_PHY_RG_LP_IIR2_K4_U 0x231 +-#define MTK_PHY_RG_LP_IIR2_K5_L 0x232 +-#define MTK_PHY_RG_LP_IIR2_K5_U 0x233 +- +-#define MTK_PHY_RG_DEV1E_REG234 0x234 +-#define MTK_PHY_TR_OPEN_LOOP_EN_MASK GENMASK(0, 0) +-#define MTK_PHY_LPF_X_AVERAGE_MASK GENMASK(7, 4) +-#define MTK_PHY_TR_LP_IIR_EEE_EN BIT(12) +- +-#define MTK_PHY_RG_LPF_CNT_VAL 0x235 +- +-#define MTK_PHY_RG_DEV1E_REG238 0x238 +-#define MTK_PHY_LPI_SLV_SEND_TX_TIMER_MASK GENMASK(8, 0) +-#define MTK_PHY_LPI_SLV_SEND_TX_EN BIT(12) +- +-#define MTK_PHY_RG_DEV1E_REG239 0x239 +-#define MTK_PHY_LPI_SEND_LOC_TIMER_MASK GENMASK(8, 0) +-#define MTK_PHY_LPI_TXPCS_LOC_RCV BIT(12) +- +-#define MTK_PHY_RG_DEV1E_REG27C 0x27c +-#define MTK_PHY_VGASTATE_FFE_THR_ST1_MASK GENMASK(12, 8) +-#define MTK_PHY_RG_DEV1E_REG27D 0x27d +-#define MTK_PHY_VGASTATE_FFE_THR_ST2_MASK GENMASK(4, 0) +- +-#define MTK_PHY_RG_DEV1E_REG2C7 0x2c7 +-#define MTK_PHY_MAX_GAIN_MASK GENMASK(4, 0) +-#define MTK_PHY_MIN_GAIN_MASK GENMASK(12, 8) +- +-#define MTK_PHY_RG_DEV1E_REG2D1 0x2d1 +-#define MTK_PHY_VCO_SLICER_THRESH_BITS_HIGH_EEE_MASK GENMASK(7, 0) +-#define MTK_PHY_LPI_SKIP_SD_SLV_TR BIT(8) +-#define MTK_PHY_LPI_TR_READY BIT(9) +-#define MTK_PHY_LPI_VCO_EEE_STG0_EN BIT(10) +- +-#define MTK_PHY_RG_DEV1E_REG323 0x323 +-#define MTK_PHY_EEE_WAKE_MAS_INT_DC BIT(0) +-#define MTK_PHY_EEE_WAKE_SLV_INT_DC BIT(4) +- +-#define MTK_PHY_RG_DEV1E_REG324 0x324 +-#define MTK_PHY_SMI_DETCNT_MAX_MASK GENMASK(5, 0) +-#define MTK_PHY_SMI_DET_MAX_EN BIT(8) +- +-#define MTK_PHY_RG_DEV1E_REG326 0x326 +-#define MTK_PHY_LPI_MODE_SD_ON BIT(0) +-#define MTK_PHY_RESET_RANDUPD_CNT BIT(1) +-#define MTK_PHY_TREC_UPDATE_ENAB_CLR BIT(2) +-#define MTK_PHY_LPI_QUIT_WAIT_DFE_SIG_DET_OFF BIT(4) +-#define MTK_PHY_TR_READY_SKIP_AFE_WAKEUP BIT(5) +- +-#define MTK_PHY_LDO_PUMP_EN_PAIRAB 0x502 +-#define MTK_PHY_LDO_PUMP_EN_PAIRCD 0x503 +- +-#define MTK_PHY_DA_TX_R50_PAIR_A 0x53d +-#define MTK_PHY_DA_TX_R50_PAIR_B 0x53e +-#define MTK_PHY_DA_TX_R50_PAIR_C 0x53f +-#define MTK_PHY_DA_TX_R50_PAIR_D 0x540 +- +-/* Registers on MDIO_MMD_VEND2 */ +-#define MTK_PHY_LED0_ON_CTRL 0x24 +-#define MTK_PHY_LED1_ON_CTRL 0x26 +-#define MTK_PHY_LED_ON_MASK GENMASK(6, 0) +-#define MTK_PHY_LED_ON_LINK1000 BIT(0) +-#define MTK_PHY_LED_ON_LINK100 BIT(1) +-#define MTK_PHY_LED_ON_LINK10 BIT(2) +-#define MTK_PHY_LED_ON_LINK (MTK_PHY_LED_ON_LINK10 |\ +- MTK_PHY_LED_ON_LINK100 |\ +- MTK_PHY_LED_ON_LINK1000) +-#define MTK_PHY_LED_ON_LINKDOWN BIT(3) +-#define MTK_PHY_LED_ON_FDX BIT(4) /* Full duplex */ +-#define MTK_PHY_LED_ON_HDX BIT(5) /* Half duplex */ +-#define MTK_PHY_LED_ON_FORCE_ON BIT(6) +-#define MTK_PHY_LED_ON_POLARITY BIT(14) +-#define MTK_PHY_LED_ON_ENABLE BIT(15) +- +-#define MTK_PHY_LED0_BLINK_CTRL 0x25 +-#define MTK_PHY_LED1_BLINK_CTRL 0x27 +-#define MTK_PHY_LED_BLINK_1000TX BIT(0) +-#define MTK_PHY_LED_BLINK_1000RX BIT(1) +-#define MTK_PHY_LED_BLINK_100TX BIT(2) +-#define MTK_PHY_LED_BLINK_100RX BIT(3) +-#define MTK_PHY_LED_BLINK_10TX BIT(4) +-#define MTK_PHY_LED_BLINK_10RX BIT(5) +-#define MTK_PHY_LED_BLINK_RX (MTK_PHY_LED_BLINK_10RX |\ +- MTK_PHY_LED_BLINK_100RX |\ +- MTK_PHY_LED_BLINK_1000RX) +-#define MTK_PHY_LED_BLINK_TX (MTK_PHY_LED_BLINK_10TX |\ +- MTK_PHY_LED_BLINK_100TX |\ +- MTK_PHY_LED_BLINK_1000TX) +-#define MTK_PHY_LED_BLINK_COLLISION BIT(6) +-#define MTK_PHY_LED_BLINK_RX_CRC_ERR BIT(7) +-#define MTK_PHY_LED_BLINK_RX_IDLE_ERR BIT(8) +-#define MTK_PHY_LED_BLINK_FORCE_BLINK BIT(9) +- +-#define MTK_PHY_LED1_DEFAULT_POLARITIES BIT(1) +- +-#define MTK_PHY_RG_BG_RASEL 0x115 +-#define MTK_PHY_RG_BG_RASEL_MASK GENMASK(2, 0) +- +-/* 'boottrap' register reflecting the configuration of the 4 PHY LEDs */ +-#define RG_GPIO_MISC_TPBANK0 0x6f0 +-#define RG_GPIO_MISC_TPBANK0_BOOTMODE GENMASK(11, 8) +- +-/* These macro privides efuse parsing for internal phy. */ +-#define EFS_DA_TX_I2MPB_A(x) (((x) >> 0) & GENMASK(5, 0)) +-#define EFS_DA_TX_I2MPB_B(x) (((x) >> 6) & GENMASK(5, 0)) +-#define EFS_DA_TX_I2MPB_C(x) (((x) >> 12) & GENMASK(5, 0)) +-#define EFS_DA_TX_I2MPB_D(x) (((x) >> 18) & GENMASK(5, 0)) +-#define EFS_DA_TX_AMP_OFFSET_A(x) (((x) >> 24) & GENMASK(5, 0)) +- +-#define EFS_DA_TX_AMP_OFFSET_B(x) (((x) >> 0) & GENMASK(5, 0)) +-#define EFS_DA_TX_AMP_OFFSET_C(x) (((x) >> 6) & GENMASK(5, 0)) +-#define EFS_DA_TX_AMP_OFFSET_D(x) (((x) >> 12) & GENMASK(5, 0)) +-#define EFS_DA_TX_R50_A(x) (((x) >> 18) & GENMASK(5, 0)) +-#define EFS_DA_TX_R50_B(x) (((x) >> 24) & GENMASK(5, 0)) +- +-#define EFS_DA_TX_R50_C(x) (((x) >> 0) & GENMASK(5, 0)) +-#define EFS_DA_TX_R50_D(x) (((x) >> 6) & GENMASK(5, 0)) +- +-#define EFS_RG_BG_RASEL(x) (((x) >> 4) & GENMASK(2, 0)) +-#define EFS_RG_REXT_TRIM(x) (((x) >> 7) & GENMASK(5, 0)) +- +-enum { +- NO_PAIR, +- PAIR_A, +- PAIR_B, +- PAIR_C, +- PAIR_D, +-}; +- +-enum calibration_mode { +- EFUSE_K, +- SW_K +-}; +- +-enum CAL_ITEM { +- REXT, +- TX_OFFSET, +- TX_AMP, +- TX_R50, +- TX_VCM +-}; +- +-enum CAL_MODE { +- EFUSE_M, +- SW_M +-}; +- +-#define MTK_PHY_LED_STATE_FORCE_ON 0 +-#define MTK_PHY_LED_STATE_FORCE_BLINK 1 +-#define MTK_PHY_LED_STATE_NETDEV 2 +- +-struct mtk_socphy_priv { +- unsigned long led_state; +-}; +- +-struct mtk_socphy_shared { +- u32 boottrap; +- struct mtk_socphy_priv priv[4]; +-}; +- +-static int mtk_socphy_read_page(struct phy_device *phydev) +-{ +- return __phy_read(phydev, MTK_EXT_PAGE_ACCESS); +-} +- +-static int mtk_socphy_write_page(struct phy_device *phydev, int page) +-{ +- return __phy_write(phydev, MTK_EXT_PAGE_ACCESS, page); +-} +- +-/* One calibration cycle consists of: +- * 1.Set DA_CALIN_FLAG high to start calibration. Keep it high +- * until AD_CAL_COMP is ready to output calibration result. +- * 2.Wait until DA_CAL_CLK is available. +- * 3.Fetch AD_CAL_COMP_OUT. +- */ +-static int cal_cycle(struct phy_device *phydev, int devad, +- u32 regnum, u16 mask, u16 cal_val) +-{ +- int reg_val; +- int ret; +- +- phy_modify_mmd(phydev, devad, regnum, +- mask, cal_val); +- phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_AD_CALIN, +- MTK_PHY_DA_CALIN_FLAG); +- +- ret = phy_read_mmd_poll_timeout(phydev, MDIO_MMD_VEND1, +- MTK_PHY_RG_AD_CAL_CLK, reg_val, +- reg_val & MTK_PHY_DA_CAL_CLK, 500, +- ANALOG_INTERNAL_OPERATION_MAX_US, false); +- if (ret) { +- phydev_err(phydev, "Calibration cycle timeout\n"); +- return ret; +- } +- +- phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_AD_CALIN, +- MTK_PHY_DA_CALIN_FLAG); +- ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_AD_CAL_COMP) >> +- MTK_PHY_AD_CAL_COMP_OUT_SHIFT; +- phydev_dbg(phydev, "cal_val: 0x%x, ret: %d\n", cal_val, ret); +- +- return ret; +-} +- +-static int rext_fill_result(struct phy_device *phydev, u16 *buf) +-{ +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG5, +- MTK_PHY_RG_REXT_TRIM_MASK, buf[0] << 8); +- phy_modify_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_RG_BG_RASEL, +- MTK_PHY_RG_BG_RASEL_MASK, buf[1]); +- +- return 0; +-} +- +-static int rext_cal_efuse(struct phy_device *phydev, u32 *buf) +-{ +- u16 rext_cal_val[2]; +- +- rext_cal_val[0] = EFS_RG_REXT_TRIM(buf[3]); +- rext_cal_val[1] = EFS_RG_BG_RASEL(buf[3]); +- rext_fill_result(phydev, rext_cal_val); +- +- return 0; +-} +- +-static int tx_offset_fill_result(struct phy_device *phydev, u16 *buf) +-{ +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_CR_TX_AMP_OFFSET_A_B, +- MTK_PHY_CR_TX_AMP_OFFSET_A_MASK, buf[0] << 8); +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_CR_TX_AMP_OFFSET_A_B, +- MTK_PHY_CR_TX_AMP_OFFSET_B_MASK, buf[1]); +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_CR_TX_AMP_OFFSET_C_D, +- MTK_PHY_CR_TX_AMP_OFFSET_C_MASK, buf[2] << 8); +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_CR_TX_AMP_OFFSET_C_D, +- MTK_PHY_CR_TX_AMP_OFFSET_D_MASK, buf[3]); +- +- return 0; +-} +- +-static int tx_offset_cal_efuse(struct phy_device *phydev, u32 *buf) +-{ +- u16 tx_offset_cal_val[4]; +- +- tx_offset_cal_val[0] = EFS_DA_TX_AMP_OFFSET_A(buf[0]); +- tx_offset_cal_val[1] = EFS_DA_TX_AMP_OFFSET_B(buf[1]); +- tx_offset_cal_val[2] = EFS_DA_TX_AMP_OFFSET_C(buf[1]); +- tx_offset_cal_val[3] = EFS_DA_TX_AMP_OFFSET_D(buf[1]); +- +- tx_offset_fill_result(phydev, tx_offset_cal_val); +- +- return 0; +-} +- +-static int tx_amp_fill_result(struct phy_device *phydev, u16 *buf) +-{ +- int i; +- int bias[16] = {}; +- const int vals_9461[16] = { 7, 1, 4, 7, +- 7, 1, 4, 7, +- 7, 1, 4, 7, +- 7, 1, 4, 7 }; +- const int vals_9481[16] = { 10, 6, 6, 10, +- 10, 6, 6, 10, +- 10, 6, 6, 10, +- 10, 6, 6, 10 }; +- switch (phydev->drv->phy_id) { +- case MTK_GPHY_ID_MT7981: +- /* We add some calibration to efuse values +- * due to board level influence. +- * GBE: +7, TBT: +1, HBT: +4, TST: +7 +- */ +- memcpy(bias, (const void *)vals_9461, sizeof(bias)); +- break; +- case MTK_GPHY_ID_MT7988: +- memcpy(bias, (const void *)vals_9481, sizeof(bias)); +- break; +- } +- +- /* Prevent overflow */ +- for (i = 0; i < 12; i++) { +- if (buf[i >> 2] + bias[i] > 63) { +- buf[i >> 2] = 63; +- bias[i] = 0; +- } +- } +- +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TXVLD_DA_RG, +- MTK_PHY_DA_TX_I2MPB_A_GBE_MASK, (buf[0] + bias[0]) << 10); +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TXVLD_DA_RG, +- MTK_PHY_DA_TX_I2MPB_A_TBT_MASK, buf[0] + bias[1]); +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_A2, +- MTK_PHY_DA_TX_I2MPB_A_HBT_MASK, (buf[0] + bias[2]) << 10); +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_A2, +- MTK_PHY_DA_TX_I2MPB_A_TST_MASK, buf[0] + bias[3]); +- +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_B1, +- MTK_PHY_DA_TX_I2MPB_B_GBE_MASK, (buf[1] + bias[4]) << 8); +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_B1, +- MTK_PHY_DA_TX_I2MPB_B_TBT_MASK, buf[1] + bias[5]); +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_B2, +- MTK_PHY_DA_TX_I2MPB_B_HBT_MASK, (buf[1] + bias[6]) << 8); +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_B2, +- MTK_PHY_DA_TX_I2MPB_B_TST_MASK, buf[1] + bias[7]); +- +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_C1, +- MTK_PHY_DA_TX_I2MPB_C_GBE_MASK, (buf[2] + bias[8]) << 8); +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_C1, +- MTK_PHY_DA_TX_I2MPB_C_TBT_MASK, buf[2] + bias[9]); +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_C2, +- MTK_PHY_DA_TX_I2MPB_C_HBT_MASK, (buf[2] + bias[10]) << 8); +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_C2, +- MTK_PHY_DA_TX_I2MPB_C_TST_MASK, buf[2] + bias[11]); +- +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_D1, +- MTK_PHY_DA_TX_I2MPB_D_GBE_MASK, (buf[3] + bias[12]) << 8); +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_D1, +- MTK_PHY_DA_TX_I2MPB_D_TBT_MASK, buf[3] + bias[13]); +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_D2, +- MTK_PHY_DA_TX_I2MPB_D_HBT_MASK, (buf[3] + bias[14]) << 8); +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_D2, +- MTK_PHY_DA_TX_I2MPB_D_TST_MASK, buf[3] + bias[15]); +- +- return 0; +-} +- +-static int tx_amp_cal_efuse(struct phy_device *phydev, u32 *buf) +-{ +- u16 tx_amp_cal_val[4]; +- +- tx_amp_cal_val[0] = EFS_DA_TX_I2MPB_A(buf[0]); +- tx_amp_cal_val[1] = EFS_DA_TX_I2MPB_B(buf[0]); +- tx_amp_cal_val[2] = EFS_DA_TX_I2MPB_C(buf[0]); +- tx_amp_cal_val[3] = EFS_DA_TX_I2MPB_D(buf[0]); +- tx_amp_fill_result(phydev, tx_amp_cal_val); +- +- return 0; +-} +- +-static int tx_r50_fill_result(struct phy_device *phydev, u16 tx_r50_cal_val, +- u8 txg_calen_x) +-{ +- int bias = 0; +- u16 reg, val; +- +- if (phydev->drv->phy_id == MTK_GPHY_ID_MT7988) +- bias = -1; +- +- val = clamp_val(bias + tx_r50_cal_val, 0, 63); +- +- switch (txg_calen_x) { +- case PAIR_A: +- reg = MTK_PHY_DA_TX_R50_PAIR_A; +- break; +- case PAIR_B: +- reg = MTK_PHY_DA_TX_R50_PAIR_B; +- break; +- case PAIR_C: +- reg = MTK_PHY_DA_TX_R50_PAIR_C; +- break; +- case PAIR_D: +- reg = MTK_PHY_DA_TX_R50_PAIR_D; +- break; +- default: +- return -EINVAL; +- } +- +- phy_write_mmd(phydev, MDIO_MMD_VEND1, reg, val | val << 8); +- +- return 0; +-} +- +-static int tx_r50_cal_efuse(struct phy_device *phydev, u32 *buf, +- u8 txg_calen_x) +-{ +- u16 tx_r50_cal_val; +- +- switch (txg_calen_x) { +- case PAIR_A: +- tx_r50_cal_val = EFS_DA_TX_R50_A(buf[1]); +- break; +- case PAIR_B: +- tx_r50_cal_val = EFS_DA_TX_R50_B(buf[1]); +- break; +- case PAIR_C: +- tx_r50_cal_val = EFS_DA_TX_R50_C(buf[2]); +- break; +- case PAIR_D: +- tx_r50_cal_val = EFS_DA_TX_R50_D(buf[2]); +- break; +- default: +- return -EINVAL; +- } +- tx_r50_fill_result(phydev, tx_r50_cal_val, txg_calen_x); +- +- return 0; +-} +- +-static int tx_vcm_cal_sw(struct phy_device *phydev, u8 rg_txreserve_x) +-{ +- u8 lower_idx, upper_idx, txreserve_val; +- u8 lower_ret, upper_ret; +- int ret; +- +- phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG0, +- MTK_PHY_RG_ANA_CALEN); +- phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG0, +- MTK_PHY_RG_CAL_CKINV); +- phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG1, +- MTK_PHY_RG_TXVOS_CALEN); +- +- switch (rg_txreserve_x) { +- case PAIR_A: +- phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, +- MTK_PHY_RG_DASN_DAC_IN0_A, +- MTK_PHY_DASN_DAC_IN0_A_MASK); +- phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, +- MTK_PHY_RG_DASN_DAC_IN1_A, +- MTK_PHY_DASN_DAC_IN1_A_MASK); +- phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, +- MTK_PHY_RG_ANA_CAL_RG0, +- MTK_PHY_RG_ZCALEN_A); +- break; +- case PAIR_B: +- phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, +- MTK_PHY_RG_DASN_DAC_IN0_B, +- MTK_PHY_DASN_DAC_IN0_B_MASK); +- phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, +- MTK_PHY_RG_DASN_DAC_IN1_B, +- MTK_PHY_DASN_DAC_IN1_B_MASK); +- phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, +- MTK_PHY_RG_ANA_CAL_RG1, +- MTK_PHY_RG_ZCALEN_B); +- break; +- case PAIR_C: +- phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, +- MTK_PHY_RG_DASN_DAC_IN0_C, +- MTK_PHY_DASN_DAC_IN0_C_MASK); +- phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, +- MTK_PHY_RG_DASN_DAC_IN1_C, +- MTK_PHY_DASN_DAC_IN1_C_MASK); +- phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, +- MTK_PHY_RG_ANA_CAL_RG1, +- MTK_PHY_RG_ZCALEN_C); +- break; +- case PAIR_D: +- phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, +- MTK_PHY_RG_DASN_DAC_IN0_D, +- MTK_PHY_DASN_DAC_IN0_D_MASK); +- phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, +- MTK_PHY_RG_DASN_DAC_IN1_D, +- MTK_PHY_DASN_DAC_IN1_D_MASK); +- phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, +- MTK_PHY_RG_ANA_CAL_RG1, +- MTK_PHY_RG_ZCALEN_D); +- break; +- default: +- ret = -EINVAL; +- goto restore; +- } +- +- lower_idx = TXRESERVE_MIN; +- upper_idx = TXRESERVE_MAX; +- +- phydev_dbg(phydev, "Start TX-VCM SW cal.\n"); +- while ((upper_idx - lower_idx) > 1) { +- txreserve_val = DIV_ROUND_CLOSEST(lower_idx + upper_idx, 2); +- ret = cal_cycle(phydev, MDIO_MMD_VEND1, MTK_PHY_RXADC_CTRL_RG9, +- MTK_PHY_DA_RX_PSBN_TBT_MASK | +- MTK_PHY_DA_RX_PSBN_HBT_MASK | +- MTK_PHY_DA_RX_PSBN_GBE_MASK | +- MTK_PHY_DA_RX_PSBN_LP_MASK, +- txreserve_val << 12 | txreserve_val << 8 | +- txreserve_val << 4 | txreserve_val); +- if (ret == 1) { +- upper_idx = txreserve_val; +- upper_ret = ret; +- } else if (ret == 0) { +- lower_idx = txreserve_val; +- lower_ret = ret; +- } else { +- goto restore; +- } +- } +- +- if (lower_idx == TXRESERVE_MIN) { +- lower_ret = cal_cycle(phydev, MDIO_MMD_VEND1, +- MTK_PHY_RXADC_CTRL_RG9, +- MTK_PHY_DA_RX_PSBN_TBT_MASK | +- MTK_PHY_DA_RX_PSBN_HBT_MASK | +- MTK_PHY_DA_RX_PSBN_GBE_MASK | +- MTK_PHY_DA_RX_PSBN_LP_MASK, +- lower_idx << 12 | lower_idx << 8 | +- lower_idx << 4 | lower_idx); +- ret = lower_ret; +- } else if (upper_idx == TXRESERVE_MAX) { +- upper_ret = cal_cycle(phydev, MDIO_MMD_VEND1, +- MTK_PHY_RXADC_CTRL_RG9, +- MTK_PHY_DA_RX_PSBN_TBT_MASK | +- MTK_PHY_DA_RX_PSBN_HBT_MASK | +- MTK_PHY_DA_RX_PSBN_GBE_MASK | +- MTK_PHY_DA_RX_PSBN_LP_MASK, +- upper_idx << 12 | upper_idx << 8 | +- upper_idx << 4 | upper_idx); +- ret = upper_ret; +- } +- if (ret < 0) +- goto restore; +- +- /* We calibrate TX-VCM in different logic. Check upper index and then +- * lower index. If this calibration is valid, apply lower index's result. +- */ +- ret = upper_ret - lower_ret; +- if (ret == 1) { +- ret = 0; +- /* Make sure we use upper_idx in our calibration system */ +- cal_cycle(phydev, MDIO_MMD_VEND1, MTK_PHY_RXADC_CTRL_RG9, +- MTK_PHY_DA_RX_PSBN_TBT_MASK | +- MTK_PHY_DA_RX_PSBN_HBT_MASK | +- MTK_PHY_DA_RX_PSBN_GBE_MASK | +- MTK_PHY_DA_RX_PSBN_LP_MASK, +- upper_idx << 12 | upper_idx << 8 | +- upper_idx << 4 | upper_idx); +- phydev_dbg(phydev, "TX-VCM SW cal result: 0x%x\n", upper_idx); +- } else if (lower_idx == TXRESERVE_MIN && upper_ret == 1 && +- lower_ret == 1) { +- ret = 0; +- cal_cycle(phydev, MDIO_MMD_VEND1, MTK_PHY_RXADC_CTRL_RG9, +- MTK_PHY_DA_RX_PSBN_TBT_MASK | +- MTK_PHY_DA_RX_PSBN_HBT_MASK | +- MTK_PHY_DA_RX_PSBN_GBE_MASK | +- MTK_PHY_DA_RX_PSBN_LP_MASK, +- lower_idx << 12 | lower_idx << 8 | +- lower_idx << 4 | lower_idx); +- phydev_warn(phydev, "TX-VCM SW cal result at low margin 0x%x\n", +- lower_idx); +- } else if (upper_idx == TXRESERVE_MAX && upper_ret == 0 && +- lower_ret == 0) { +- ret = 0; +- phydev_warn(phydev, "TX-VCM SW cal result at high margin 0x%x\n", +- upper_idx); +- } else { +- ret = -EINVAL; +- } +- +-restore: +- phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG0, +- MTK_PHY_RG_ANA_CALEN); +- phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG1, +- MTK_PHY_RG_TXVOS_CALEN); +- phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG0, +- MTK_PHY_RG_ZCALEN_A); +- phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG1, +- MTK_PHY_RG_ZCALEN_B | MTK_PHY_RG_ZCALEN_C | +- MTK_PHY_RG_ZCALEN_D); +- +- return ret; +-} +- +-static void mt798x_phy_common_finetune(struct phy_device *phydev) +-{ +- phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); +- /* SlvDSPreadyTime = 24, MasDSPreadyTime = 24 */ +- __phy_write(phydev, 0x11, 0xc71); +- __phy_write(phydev, 0x12, 0xc); +- __phy_write(phydev, 0x10, 0x8fae); +- +- /* EnabRandUpdTrig = 1 */ +- __phy_write(phydev, 0x11, 0x2f00); +- __phy_write(phydev, 0x12, 0xe); +- __phy_write(phydev, 0x10, 0x8fb0); +- +- /* NormMseLoThresh = 85 */ +- __phy_write(phydev, 0x11, 0x55a0); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x83aa); +- +- /* FfeUpdGainForce = 1(Enable), FfeUpdGainForceVal = 4 */ +- __phy_write(phydev, 0x11, 0x240); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x9680); +- +- /* TrFreeze = 0 (mt7988 default) */ +- __phy_write(phydev, 0x11, 0x0); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x9686); +- +- /* SSTrKp100 = 5 */ +- /* SSTrKf100 = 6 */ +- /* SSTrKp1000Mas = 5 */ +- /* SSTrKf1000Mas = 6 */ +- /* SSTrKp1000Slv = 5 */ +- /* SSTrKf1000Slv = 6 */ +- __phy_write(phydev, 0x11, 0xbaef); +- __phy_write(phydev, 0x12, 0x2e); +- __phy_write(phydev, 0x10, 0x968c); +- phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); +-} +- +-static void mt7981_phy_finetune(struct phy_device *phydev) +-{ +- u16 val[8] = { 0x01ce, 0x01c1, +- 0x020f, 0x0202, +- 0x03d0, 0x03c0, +- 0x0013, 0x0005 }; +- int i, k; +- +- /* 100M eye finetune: +- * Keep middle level of TX MLT3 shapper as default. +- * Only change TX MLT3 overshoot level here. +- */ +- for (k = 0, i = 1; i < 12; i++) { +- if (i % 3 == 0) +- continue; +- phy_write_mmd(phydev, MDIO_MMD_VEND1, i, val[k++]); +- } +- +- phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); +- /* ResetSyncOffset = 6 */ +- __phy_write(phydev, 0x11, 0x600); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x8fc0); +- +- /* VgaDecRate = 1 */ +- __phy_write(phydev, 0x11, 0x4c2a); +- __phy_write(phydev, 0x12, 0x3e); +- __phy_write(phydev, 0x10, 0x8fa4); +- +- /* MrvlTrFix100Kp = 3, MrvlTrFix100Kf = 2, +- * MrvlTrFix1000Kp = 3, MrvlTrFix1000Kf = 2 +- */ +- __phy_write(phydev, 0x11, 0xd10a); +- __phy_write(phydev, 0x12, 0x34); +- __phy_write(phydev, 0x10, 0x8f82); +- +- /* VcoSlicerThreshBitsHigh */ +- __phy_write(phydev, 0x11, 0x5555); +- __phy_write(phydev, 0x12, 0x55); +- __phy_write(phydev, 0x10, 0x8ec0); +- phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); +- +- /* TR_OPEN_LOOP_EN = 1, lpf_x_average = 9 */ +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG234, +- MTK_PHY_TR_OPEN_LOOP_EN_MASK | MTK_PHY_LPF_X_AVERAGE_MASK, +- BIT(0) | FIELD_PREP(MTK_PHY_LPF_X_AVERAGE_MASK, 0x9)); +- +- /* rg_tr_lpf_cnt_val = 512 */ +- phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LPF_CNT_VAL, 0x200); +- +- /* IIR2 related */ +- phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K1_L, 0x82); +- phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K1_U, 0x0); +- phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K2_L, 0x103); +- phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K2_U, 0x0); +- phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K3_L, 0x82); +- phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K3_U, 0x0); +- phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K4_L, 0xd177); +- phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K4_U, 0x3); +- phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K5_L, 0x2c82); +- phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K5_U, 0xe); +- +- /* FFE peaking */ +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG27C, +- MTK_PHY_VGASTATE_FFE_THR_ST1_MASK, 0x1b << 8); +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG27D, +- MTK_PHY_VGASTATE_FFE_THR_ST2_MASK, 0x1e); +- +- /* Disable LDO pump */ +- phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_LDO_PUMP_EN_PAIRAB, 0x0); +- phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_LDO_PUMP_EN_PAIRCD, 0x0); +- /* Adjust LDO output voltage */ +- phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_LDO_OUTPUT_V, 0x2222); +-} +- +-static void mt7988_phy_finetune(struct phy_device *phydev) +-{ +- u16 val[12] = { 0x0187, 0x01cd, 0x01c8, 0x0182, +- 0x020d, 0x0206, 0x0384, 0x03d0, +- 0x03c6, 0x030a, 0x0011, 0x0005 }; +- int i; +- +- /* Set default MLT3 shaper first */ +- for (i = 0; i < 12; i++) +- phy_write_mmd(phydev, MDIO_MMD_VEND1, i, val[i]); +- +- /* TCT finetune */ +- phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_TX_FILTER, 0x5); +- +- phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); +- /* ResetSyncOffset = 5 */ +- __phy_write(phydev, 0x11, 0x500); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x8fc0); +- +- /* VgaDecRate is 1 at default on mt7988 */ +- +- /* MrvlTrFix100Kp = 6, MrvlTrFix100Kf = 7, +- * MrvlTrFix1000Kp = 6, MrvlTrFix1000Kf = 7 +- */ +- __phy_write(phydev, 0x11, 0xb90a); +- __phy_write(phydev, 0x12, 0x6f); +- __phy_write(phydev, 0x10, 0x8f82); +- +- /* RemAckCntLimitCtrl = 1 */ +- __phy_write(phydev, 0x11, 0xfbba); +- __phy_write(phydev, 0x12, 0xc3); +- __phy_write(phydev, 0x10, 0x87f8); +- +- phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); +- +- /* TR_OPEN_LOOP_EN = 1, lpf_x_average = 10 */ +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG234, +- MTK_PHY_TR_OPEN_LOOP_EN_MASK | MTK_PHY_LPF_X_AVERAGE_MASK, +- BIT(0) | FIELD_PREP(MTK_PHY_LPF_X_AVERAGE_MASK, 0xa)); +- +- /* rg_tr_lpf_cnt_val = 1023 */ +- phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LPF_CNT_VAL, 0x3ff); +-} +- +-static void mt798x_phy_eee(struct phy_device *phydev) +-{ +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, +- MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG120, +- MTK_PHY_LPI_SIG_EN_LO_THRESH1000_MASK | +- MTK_PHY_LPI_SIG_EN_HI_THRESH1000_MASK, +- FIELD_PREP(MTK_PHY_LPI_SIG_EN_LO_THRESH1000_MASK, 0x0) | +- FIELD_PREP(MTK_PHY_LPI_SIG_EN_HI_THRESH1000_MASK, 0x14)); +- +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, +- MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG122, +- MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK, +- FIELD_PREP(MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK, +- 0xff)); +- +- phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, +- MTK_PHY_RG_TESTMUX_ADC_CTRL, +- MTK_PHY_RG_TXEN_DIG_MASK); +- +- phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, +- MTK_PHY_RG_DEV1E_REG19b, MTK_PHY_BYPASS_DSP_LPI_READY); +- +- phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, +- MTK_PHY_RG_DEV1E_REG234, MTK_PHY_TR_LP_IIR_EEE_EN); +- +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG238, +- MTK_PHY_LPI_SLV_SEND_TX_TIMER_MASK | +- MTK_PHY_LPI_SLV_SEND_TX_EN, +- FIELD_PREP(MTK_PHY_LPI_SLV_SEND_TX_TIMER_MASK, 0x120)); +- +- /* Keep MTK_PHY_LPI_SEND_LOC_TIMER as 375 */ +- phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG239, +- MTK_PHY_LPI_TXPCS_LOC_RCV); +- +- /* This also fixes some IoT issues, such as CH340 */ +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG2C7, +- MTK_PHY_MAX_GAIN_MASK | MTK_PHY_MIN_GAIN_MASK, +- FIELD_PREP(MTK_PHY_MAX_GAIN_MASK, 0x8) | +- FIELD_PREP(MTK_PHY_MIN_GAIN_MASK, 0x13)); +- +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG2D1, +- MTK_PHY_VCO_SLICER_THRESH_BITS_HIGH_EEE_MASK, +- FIELD_PREP(MTK_PHY_VCO_SLICER_THRESH_BITS_HIGH_EEE_MASK, +- 0x33) | +- MTK_PHY_LPI_SKIP_SD_SLV_TR | MTK_PHY_LPI_TR_READY | +- MTK_PHY_LPI_VCO_EEE_STG0_EN); +- +- phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG323, +- MTK_PHY_EEE_WAKE_MAS_INT_DC | +- MTK_PHY_EEE_WAKE_SLV_INT_DC); +- +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG324, +- MTK_PHY_SMI_DETCNT_MAX_MASK, +- FIELD_PREP(MTK_PHY_SMI_DETCNT_MAX_MASK, 0x3f) | +- MTK_PHY_SMI_DET_MAX_EN); +- +- phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG326, +- MTK_PHY_LPI_MODE_SD_ON | MTK_PHY_RESET_RANDUPD_CNT | +- MTK_PHY_TREC_UPDATE_ENAB_CLR | +- MTK_PHY_LPI_QUIT_WAIT_DFE_SIG_DET_OFF | +- MTK_PHY_TR_READY_SKIP_AFE_WAKEUP); +- +- phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); +- /* Regsigdet_sel_1000 = 0 */ +- __phy_write(phydev, 0x11, 0xb); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x9690); +- +- /* REG_EEE_st2TrKf1000 = 2 */ +- __phy_write(phydev, 0x11, 0x114f); +- __phy_write(phydev, 0x12, 0x2); +- __phy_write(phydev, 0x10, 0x969a); +- +- /* RegEEE_slv_wake_tr_timer_tar = 6, RegEEE_slv_remtx_timer_tar = 20 */ +- __phy_write(phydev, 0x11, 0x3028); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x969e); +- +- /* RegEEE_slv_wake_int_timer_tar = 8 */ +- __phy_write(phydev, 0x11, 0x5010); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x96a0); +- +- /* RegEEE_trfreeze_timer2 = 586 */ +- __phy_write(phydev, 0x11, 0x24a); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x96a8); +- +- /* RegEEE100Stg1_tar = 16 */ +- __phy_write(phydev, 0x11, 0x3210); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x96b8); +- +- /* REGEEE_wake_slv_tr_wait_dfesigdet_en = 0 */ +- __phy_write(phydev, 0x11, 0x1463); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x96ca); +- +- /* DfeTailEnableVgaThresh1000 = 27 */ +- __phy_write(phydev, 0x11, 0x36); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x8f80); +- phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); +- +- phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_3); +- __phy_modify(phydev, MTK_PHY_LPI_REG_14, MTK_PHY_LPI_WAKE_TIMER_1000_MASK, +- FIELD_PREP(MTK_PHY_LPI_WAKE_TIMER_1000_MASK, 0x19c)); +- +- __phy_modify(phydev, MTK_PHY_LPI_REG_1c, MTK_PHY_SMI_DET_ON_THRESH_MASK, +- FIELD_PREP(MTK_PHY_SMI_DET_ON_THRESH_MASK, 0xc)); +- phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); +- +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, +- MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG122, +- MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK, +- FIELD_PREP(MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK, 0xff)); +-} +- +-static int cal_sw(struct phy_device *phydev, enum CAL_ITEM cal_item, +- u8 start_pair, u8 end_pair) +-{ +- u8 pair_n; +- int ret; +- +- for (pair_n = start_pair; pair_n <= end_pair; pair_n++) { +- /* TX_OFFSET & TX_AMP have no SW calibration. */ +- switch (cal_item) { +- case TX_VCM: +- ret = tx_vcm_cal_sw(phydev, pair_n); +- break; +- default: +- return -EINVAL; +- } +- if (ret) +- return ret; +- } +- return 0; +-} +- +-static int cal_efuse(struct phy_device *phydev, enum CAL_ITEM cal_item, +- u8 start_pair, u8 end_pair, u32 *buf) +-{ +- u8 pair_n; +- int ret; +- +- for (pair_n = start_pair; pair_n <= end_pair; pair_n++) { +- /* TX_VCM has no efuse calibration. */ +- switch (cal_item) { +- case REXT: +- ret = rext_cal_efuse(phydev, buf); +- break; +- case TX_OFFSET: +- ret = tx_offset_cal_efuse(phydev, buf); +- break; +- case TX_AMP: +- ret = tx_amp_cal_efuse(phydev, buf); +- break; +- case TX_R50: +- ret = tx_r50_cal_efuse(phydev, buf, pair_n); +- break; +- default: +- return -EINVAL; +- } +- if (ret) +- return ret; +- } +- +- return 0; +-} +- +-static int start_cal(struct phy_device *phydev, enum CAL_ITEM cal_item, +- enum CAL_MODE cal_mode, u8 start_pair, +- u8 end_pair, u32 *buf) +-{ +- int ret; +- +- switch (cal_mode) { +- case EFUSE_M: +- ret = cal_efuse(phydev, cal_item, start_pair, +- end_pair, buf); +- break; +- case SW_M: +- ret = cal_sw(phydev, cal_item, start_pair, end_pair); +- break; +- default: +- return -EINVAL; +- } +- +- if (ret) { +- phydev_err(phydev, "cal %d failed\n", cal_item); +- return -EIO; +- } +- +- return 0; +-} +- +-static int mt798x_phy_calibration(struct phy_device *phydev) +-{ +- int ret = 0; +- u32 *buf; +- size_t len; +- struct nvmem_cell *cell; +- +- cell = nvmem_cell_get(&phydev->mdio.dev, "phy-cal-data"); +- if (IS_ERR(cell)) { +- if (PTR_ERR(cell) == -EPROBE_DEFER) +- return PTR_ERR(cell); +- return 0; +- } +- +- buf = (u32 *)nvmem_cell_read(cell, &len); +- if (IS_ERR(buf)) +- return PTR_ERR(buf); +- nvmem_cell_put(cell); +- +- if (!buf[0] || !buf[1] || !buf[2] || !buf[3] || len < 4 * sizeof(u32)) { +- phydev_err(phydev, "invalid efuse data\n"); +- ret = -EINVAL; +- goto out; +- } +- +- ret = start_cal(phydev, REXT, EFUSE_M, NO_PAIR, NO_PAIR, buf); +- if (ret) +- goto out; +- ret = start_cal(phydev, TX_OFFSET, EFUSE_M, NO_PAIR, NO_PAIR, buf); +- if (ret) +- goto out; +- ret = start_cal(phydev, TX_AMP, EFUSE_M, NO_PAIR, NO_PAIR, buf); +- if (ret) +- goto out; +- ret = start_cal(phydev, TX_R50, EFUSE_M, PAIR_A, PAIR_D, buf); +- if (ret) +- goto out; +- ret = start_cal(phydev, TX_VCM, SW_M, PAIR_A, PAIR_A, buf); +- if (ret) +- goto out; +- +-out: +- kfree(buf); +- return ret; +-} +- +-static int mt798x_phy_config_init(struct phy_device *phydev) +-{ +- switch (phydev->drv->phy_id) { +- case MTK_GPHY_ID_MT7981: +- mt7981_phy_finetune(phydev); +- break; +- case MTK_GPHY_ID_MT7988: +- mt7988_phy_finetune(phydev); +- break; +- } +- +- mt798x_phy_common_finetune(phydev); +- mt798x_phy_eee(phydev); +- +- return mt798x_phy_calibration(phydev); +-} +- +-static int mt798x_phy_hw_led_on_set(struct phy_device *phydev, u8 index, +- bool on) +-{ +- unsigned int bit_on = MTK_PHY_LED_STATE_FORCE_ON + (index ? 16 : 0); +- struct mtk_socphy_priv *priv = phydev->priv; +- bool changed; +- +- if (on) +- changed = !test_and_set_bit(bit_on, &priv->led_state); +- else +- changed = !!test_and_clear_bit(bit_on, &priv->led_state); +- +- changed |= !!test_and_clear_bit(MTK_PHY_LED_STATE_NETDEV + +- (index ? 16 : 0), &priv->led_state); +- if (changed) +- return phy_modify_mmd(phydev, MDIO_MMD_VEND2, index ? +- MTK_PHY_LED1_ON_CTRL : MTK_PHY_LED0_ON_CTRL, +- MTK_PHY_LED_ON_MASK, +- on ? MTK_PHY_LED_ON_FORCE_ON : 0); +- else +- return 0; +-} +- +-static int mt798x_phy_hw_led_blink_set(struct phy_device *phydev, u8 index, +- bool blinking) +-{ +- unsigned int bit_blink = MTK_PHY_LED_STATE_FORCE_BLINK + (index ? 16 : 0); +- struct mtk_socphy_priv *priv = phydev->priv; +- bool changed; +- +- if (blinking) +- changed = !test_and_set_bit(bit_blink, &priv->led_state); +- else +- changed = !!test_and_clear_bit(bit_blink, &priv->led_state); +- +- changed |= !!test_bit(MTK_PHY_LED_STATE_NETDEV + +- (index ? 16 : 0), &priv->led_state); +- if (changed) +- return phy_write_mmd(phydev, MDIO_MMD_VEND2, index ? +- MTK_PHY_LED1_BLINK_CTRL : MTK_PHY_LED0_BLINK_CTRL, +- blinking ? MTK_PHY_LED_BLINK_FORCE_BLINK : 0); +- else +- return 0; +-} +- +-static int mt798x_phy_led_blink_set(struct phy_device *phydev, u8 index, +- unsigned long *delay_on, +- unsigned long *delay_off) +-{ +- bool blinking = false; +- int err = 0; +- +- if (index > 1) +- return -EINVAL; +- +- if (delay_on && delay_off && (*delay_on > 0) && (*delay_off > 0)) { +- blinking = true; +- *delay_on = 50; +- *delay_off = 50; +- } +- +- err = mt798x_phy_hw_led_blink_set(phydev, index, blinking); +- if (err) +- return err; +- +- return mt798x_phy_hw_led_on_set(phydev, index, false); +-} +- +-static int mt798x_phy_led_brightness_set(struct phy_device *phydev, +- u8 index, enum led_brightness value) +-{ +- int err; +- +- err = mt798x_phy_hw_led_blink_set(phydev, index, false); +- if (err) +- return err; +- +- return mt798x_phy_hw_led_on_set(phydev, index, (value != LED_OFF)); +-} +- +-static const unsigned long supported_triggers = (BIT(TRIGGER_NETDEV_FULL_DUPLEX) | +- BIT(TRIGGER_NETDEV_HALF_DUPLEX) | +- BIT(TRIGGER_NETDEV_LINK) | +- BIT(TRIGGER_NETDEV_LINK_10) | +- BIT(TRIGGER_NETDEV_LINK_100) | +- BIT(TRIGGER_NETDEV_LINK_1000) | +- BIT(TRIGGER_NETDEV_RX) | +- BIT(TRIGGER_NETDEV_TX)); +- +-static int mt798x_phy_led_hw_is_supported(struct phy_device *phydev, u8 index, +- unsigned long rules) +-{ +- if (index > 1) +- return -EINVAL; +- +- /* All combinations of the supported triggers are allowed */ +- if (rules & ~supported_triggers) +- return -EOPNOTSUPP; +- +- return 0; +-}; +- +-static int mt798x_phy_led_hw_control_get(struct phy_device *phydev, u8 index, +- unsigned long *rules) +-{ +- unsigned int bit_blink = MTK_PHY_LED_STATE_FORCE_BLINK + (index ? 16 : 0); +- unsigned int bit_netdev = MTK_PHY_LED_STATE_NETDEV + (index ? 16 : 0); +- unsigned int bit_on = MTK_PHY_LED_STATE_FORCE_ON + (index ? 16 : 0); +- struct mtk_socphy_priv *priv = phydev->priv; +- int on, blink; +- +- if (index > 1) +- return -EINVAL; +- +- on = phy_read_mmd(phydev, MDIO_MMD_VEND2, +- index ? MTK_PHY_LED1_ON_CTRL : MTK_PHY_LED0_ON_CTRL); +- +- if (on < 0) +- return -EIO; +- +- blink = phy_read_mmd(phydev, MDIO_MMD_VEND2, +- index ? MTK_PHY_LED1_BLINK_CTRL : +- MTK_PHY_LED0_BLINK_CTRL); +- if (blink < 0) +- return -EIO; +- +- if ((on & (MTK_PHY_LED_ON_LINK | MTK_PHY_LED_ON_FDX | MTK_PHY_LED_ON_HDX | +- MTK_PHY_LED_ON_LINKDOWN)) || +- (blink & (MTK_PHY_LED_BLINK_RX | MTK_PHY_LED_BLINK_TX))) +- set_bit(bit_netdev, &priv->led_state); +- else +- clear_bit(bit_netdev, &priv->led_state); +- +- if (on & MTK_PHY_LED_ON_FORCE_ON) +- set_bit(bit_on, &priv->led_state); +- else +- clear_bit(bit_on, &priv->led_state); +- +- if (blink & MTK_PHY_LED_BLINK_FORCE_BLINK) +- set_bit(bit_blink, &priv->led_state); +- else +- clear_bit(bit_blink, &priv->led_state); +- +- if (!rules) +- return 0; +- +- if (on & MTK_PHY_LED_ON_LINK) +- *rules |= BIT(TRIGGER_NETDEV_LINK); +- +- if (on & MTK_PHY_LED_ON_LINK10) +- *rules |= BIT(TRIGGER_NETDEV_LINK_10); +- +- if (on & MTK_PHY_LED_ON_LINK100) +- *rules |= BIT(TRIGGER_NETDEV_LINK_100); +- +- if (on & MTK_PHY_LED_ON_LINK1000) +- *rules |= BIT(TRIGGER_NETDEV_LINK_1000); +- +- if (on & MTK_PHY_LED_ON_FDX) +- *rules |= BIT(TRIGGER_NETDEV_FULL_DUPLEX); +- +- if (on & MTK_PHY_LED_ON_HDX) +- *rules |= BIT(TRIGGER_NETDEV_HALF_DUPLEX); +- +- if (blink & MTK_PHY_LED_BLINK_RX) +- *rules |= BIT(TRIGGER_NETDEV_RX); +- +- if (blink & MTK_PHY_LED_BLINK_TX) +- *rules |= BIT(TRIGGER_NETDEV_TX); +- +- return 0; +-}; +- +-static int mt798x_phy_led_hw_control_set(struct phy_device *phydev, u8 index, +- unsigned long rules) +-{ +- unsigned int bit_netdev = MTK_PHY_LED_STATE_NETDEV + (index ? 16 : 0); +- struct mtk_socphy_priv *priv = phydev->priv; +- u16 on = 0, blink = 0; +- int ret; +- +- if (index > 1) +- return -EINVAL; +- +- if (rules & BIT(TRIGGER_NETDEV_FULL_DUPLEX)) +- on |= MTK_PHY_LED_ON_FDX; +- +- if (rules & BIT(TRIGGER_NETDEV_HALF_DUPLEX)) +- on |= MTK_PHY_LED_ON_HDX; +- +- if (rules & (BIT(TRIGGER_NETDEV_LINK_10) | BIT(TRIGGER_NETDEV_LINK))) +- on |= MTK_PHY_LED_ON_LINK10; +- +- if (rules & (BIT(TRIGGER_NETDEV_LINK_100) | BIT(TRIGGER_NETDEV_LINK))) +- on |= MTK_PHY_LED_ON_LINK100; +- +- if (rules & (BIT(TRIGGER_NETDEV_LINK_1000) | BIT(TRIGGER_NETDEV_LINK))) +- on |= MTK_PHY_LED_ON_LINK1000; +- +- if (rules & BIT(TRIGGER_NETDEV_RX)) { +- blink |= (on & MTK_PHY_LED_ON_LINK) ? +- (((on & MTK_PHY_LED_ON_LINK10) ? MTK_PHY_LED_BLINK_10RX : 0) | +- ((on & MTK_PHY_LED_ON_LINK100) ? MTK_PHY_LED_BLINK_100RX : 0) | +- ((on & MTK_PHY_LED_ON_LINK1000) ? MTK_PHY_LED_BLINK_1000RX : 0)) : +- MTK_PHY_LED_BLINK_RX; +- } +- +- if (rules & BIT(TRIGGER_NETDEV_TX)) { +- blink |= (on & MTK_PHY_LED_ON_LINK) ? +- (((on & MTK_PHY_LED_ON_LINK10) ? MTK_PHY_LED_BLINK_10TX : 0) | +- ((on & MTK_PHY_LED_ON_LINK100) ? MTK_PHY_LED_BLINK_100TX : 0) | +- ((on & MTK_PHY_LED_ON_LINK1000) ? MTK_PHY_LED_BLINK_1000TX : 0)) : +- MTK_PHY_LED_BLINK_TX; +- } +- +- if (blink || on) +- set_bit(bit_netdev, &priv->led_state); +- else +- clear_bit(bit_netdev, &priv->led_state); +- +- ret = phy_modify_mmd(phydev, MDIO_MMD_VEND2, index ? +- MTK_PHY_LED1_ON_CTRL : +- MTK_PHY_LED0_ON_CTRL, +- MTK_PHY_LED_ON_FDX | +- MTK_PHY_LED_ON_HDX | +- MTK_PHY_LED_ON_LINK, +- on); +- +- if (ret) +- return ret; +- +- return phy_write_mmd(phydev, MDIO_MMD_VEND2, index ? +- MTK_PHY_LED1_BLINK_CTRL : +- MTK_PHY_LED0_BLINK_CTRL, blink); +-}; +- +-static bool mt7988_phy_led_get_polarity(struct phy_device *phydev, int led_num) +-{ +- struct mtk_socphy_shared *priv = phydev->shared->priv; +- u32 polarities; +- +- if (led_num == 0) +- polarities = ~(priv->boottrap); +- else +- polarities = MTK_PHY_LED1_DEFAULT_POLARITIES; +- +- if (polarities & BIT(phydev->mdio.addr)) +- return true; +- +- return false; +-} +- +-static int mt7988_phy_fix_leds_polarities(struct phy_device *phydev) +-{ +- struct pinctrl *pinctrl; +- int index; +- +- /* Setup LED polarity according to bootstrap use of LED pins */ +- for (index = 0; index < 2; ++index) +- phy_modify_mmd(phydev, MDIO_MMD_VEND2, index ? +- MTK_PHY_LED1_ON_CTRL : MTK_PHY_LED0_ON_CTRL, +- MTK_PHY_LED_ON_POLARITY, +- mt7988_phy_led_get_polarity(phydev, index) ? +- MTK_PHY_LED_ON_POLARITY : 0); +- +- /* Only now setup pinctrl to avoid bogus blinking */ +- pinctrl = devm_pinctrl_get_select(&phydev->mdio.dev, "gbe-led"); +- if (IS_ERR(pinctrl)) +- dev_err(&phydev->mdio.bus->dev, "Failed to setup PHY LED pinctrl\n"); +- +- return 0; +-} +- +-static int mt7988_phy_probe_shared(struct phy_device *phydev) +-{ +- struct device_node *np = dev_of_node(&phydev->mdio.bus->dev); +- struct mtk_socphy_shared *shared = phydev->shared->priv; +- struct regmap *regmap; +- u32 reg; +- int ret; +- +- /* The LED0 of the 4 PHYs in MT7988 are wired to SoC pins LED_A, LED_B, +- * LED_C and LED_D respectively. At the same time those pins are used to +- * bootstrap configuration of the reference clock source (LED_A), +- * DRAM DDRx16b x2/x1 (LED_B) and boot device (LED_C, LED_D). +- * In practise this is done using a LED and a resistor pulling the pin +- * either to GND or to VIO. +- * The detected value at boot time is accessible at run-time using the +- * TPBANK0 register located in the gpio base of the pinctrl, in order +- * to read it here it needs to be referenced by a phandle called +- * 'mediatek,pio' in the MDIO bus hosting the PHY. +- * The 4 bits in TPBANK0 are kept as package shared data and are used to +- * set LED polarity for each of the LED0. +- */ +- regmap = syscon_regmap_lookup_by_phandle(np, "mediatek,pio"); +- if (IS_ERR(regmap)) +- return PTR_ERR(regmap); +- +- ret = regmap_read(regmap, RG_GPIO_MISC_TPBANK0, ®); +- if (ret) +- return ret; +- +- shared->boottrap = FIELD_GET(RG_GPIO_MISC_TPBANK0_BOOTMODE, reg); +- +- return 0; +-} +- +-static void mt798x_phy_leds_state_init(struct phy_device *phydev) +-{ +- int i; +- +- for (i = 0; i < 2; ++i) +- mt798x_phy_led_hw_control_get(phydev, i, NULL); +-} +- +-static int mt7988_phy_probe(struct phy_device *phydev) +-{ +- struct mtk_socphy_shared *shared; +- struct mtk_socphy_priv *priv; +- int err; +- +- if (phydev->mdio.addr > 3) +- return -EINVAL; +- +- err = devm_phy_package_join(&phydev->mdio.dev, phydev, 0, +- sizeof(struct mtk_socphy_shared)); +- if (err) +- return err; +- +- if (phy_package_probe_once(phydev)) { +- err = mt7988_phy_probe_shared(phydev); +- if (err) +- return err; +- } +- +- shared = phydev->shared->priv; +- priv = &shared->priv[phydev->mdio.addr]; +- +- phydev->priv = priv; +- +- mt798x_phy_leds_state_init(phydev); +- +- err = mt7988_phy_fix_leds_polarities(phydev); +- if (err) +- return err; +- +- /* Disable TX power saving at probing to: +- * 1. Meet common mode compliance test criteria +- * 2. Make sure that TX-VCM calibration works fine +- */ +- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RXADC_CTRL_RG7, +- MTK_PHY_DA_AD_BUF_BIAS_LP_MASK, 0x3 << 8); +- +- return mt798x_phy_calibration(phydev); +-} +- +-static int mt7981_phy_probe(struct phy_device *phydev) +-{ +- struct mtk_socphy_priv *priv; +- +- priv = devm_kzalloc(&phydev->mdio.dev, sizeof(struct mtk_socphy_priv), +- GFP_KERNEL); +- if (!priv) +- return -ENOMEM; +- +- phydev->priv = priv; +- +- mt798x_phy_leds_state_init(phydev); +- +- return mt798x_phy_calibration(phydev); +-} +- +-static struct phy_driver mtk_socphy_driver[] = { +- { +- PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7981), +- .name = "MediaTek MT7981 PHY", +- .config_init = mt798x_phy_config_init, +- .config_intr = genphy_no_config_intr, +- .handle_interrupt = genphy_handle_interrupt_no_ack, +- .probe = mt7981_phy_probe, +- .suspend = genphy_suspend, +- .resume = genphy_resume, +- .read_page = mtk_socphy_read_page, +- .write_page = mtk_socphy_write_page, +- .led_blink_set = mt798x_phy_led_blink_set, +- .led_brightness_set = mt798x_phy_led_brightness_set, +- .led_hw_is_supported = mt798x_phy_led_hw_is_supported, +- .led_hw_control_set = mt798x_phy_led_hw_control_set, +- .led_hw_control_get = mt798x_phy_led_hw_control_get, +- }, +- { +- PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7988), +- .name = "MediaTek MT7988 PHY", +- .config_init = mt798x_phy_config_init, +- .config_intr = genphy_no_config_intr, +- .handle_interrupt = genphy_handle_interrupt_no_ack, +- .probe = mt7988_phy_probe, +- .suspend = genphy_suspend, +- .resume = genphy_resume, +- .read_page = mtk_socphy_read_page, +- .write_page = mtk_socphy_write_page, +- .led_blink_set = mt798x_phy_led_blink_set, +- .led_brightness_set = mt798x_phy_led_brightness_set, +- .led_hw_is_supported = mt798x_phy_led_hw_is_supported, +- .led_hw_control_set = mt798x_phy_led_hw_control_set, +- .led_hw_control_get = mt798x_phy_led_hw_control_get, +- }, +-}; +- +-module_phy_driver(mtk_socphy_driver); +- +-static struct mdio_device_id __maybe_unused mtk_socphy_tbl[] = { +- { PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7981) }, +- { PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7988) }, +- { } +-}; +- +-MODULE_DESCRIPTION("MediaTek SoC Gigabit Ethernet PHY driver"); +-MODULE_AUTHOR("Daniel Golle "); +-MODULE_AUTHOR("SkyLake Huang "); +-MODULE_LICENSE("GPL"); +- +-MODULE_DEVICE_TABLE(mdio, mtk_socphy_tbl); +--- a/drivers/net/phy/mediatek-ge.c ++++ /dev/null +@@ -1,148 +0,0 @@ +-// SPDX-License-Identifier: GPL-2.0+ +-#include +-#include +-#include +-#include +- +-#define MTK_EXT_PAGE_ACCESS 0x1f +-#define MTK_PHY_PAGE_STANDARD 0x0000 +-#define MTK_PHY_PAGE_EXTENDED 0x0001 +-#define MTK_PHY_PAGE_EXTENDED_2 0x0002 +-#define MTK_PHY_PAGE_EXTENDED_3 0x0003 +-#define MTK_PHY_PAGE_EXTENDED_2A30 0x2a30 +-#define MTK_PHY_PAGE_EXTENDED_52B5 0x52b5 +- +-static int mtk_gephy_read_page(struct phy_device *phydev) +-{ +- return __phy_read(phydev, MTK_EXT_PAGE_ACCESS); +-} +- +-static int mtk_gephy_write_page(struct phy_device *phydev, int page) +-{ +- return __phy_write(phydev, MTK_EXT_PAGE_ACCESS, page); +-} +- +-static void mtk_gephy_config_init(struct phy_device *phydev) +-{ +- /* Disable EEE */ +- phy_write_mmd(phydev, MDIO_MMD_AN, MDIO_AN_EEE_ADV, 0); +- +- /* Enable HW auto downshift */ +- phy_modify_paged(phydev, MTK_PHY_PAGE_EXTENDED, 0x14, 0, BIT(4)); +- +- /* Increase SlvDPSready time */ +- phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); +- __phy_write(phydev, 0x10, 0xafae); +- __phy_write(phydev, 0x12, 0x2f); +- __phy_write(phydev, 0x10, 0x8fae); +- phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); +- +- /* Adjust 100_mse_threshold */ +- phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x123, 0xffff); +- +- /* Disable mcc */ +- phy_write_mmd(phydev, MDIO_MMD_VEND1, 0xa6, 0x300); +-} +- +-static int mt7530_phy_config_init(struct phy_device *phydev) +-{ +- mtk_gephy_config_init(phydev); +- +- /* Increase post_update_timer */ +- phy_write_paged(phydev, MTK_PHY_PAGE_EXTENDED_3, 0x11, 0x4b); +- +- return 0; +-} +- +-static int mt7530_led_config_of(struct phy_device *phydev) +-{ +- struct device_node *np = phydev->mdio.dev.of_node; +- const __be32 *paddr; +- int len; +- int i; +- +- paddr = of_get_property(np, "mediatek,led-config", &len); +- if (!paddr) +- return 0; +- +- if (len < (2 * sizeof(*paddr))) +- return -EINVAL; +- +- len /= sizeof(*paddr); +- +- phydev_warn(phydev, "Configure LED registers (num=%d)\n", len); +- for (i = 0; i < len - 1; i += 2) { +- u32 reg; +- u32 val; +- +- reg = be32_to_cpup(paddr + i); +- val = be32_to_cpup(paddr + i + 1); +- +- phy_write_mmd(phydev, MDIO_MMD_VEND2, reg, val); +- } +- +- return 0; +-} +- +-static int mt7531_phy_config_init(struct phy_device *phydev) +-{ +- mtk_gephy_config_init(phydev); +- +- /* PHY link down power saving enable */ +- phy_set_bits(phydev, 0x17, BIT(4)); +- phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, 0xc6, 0x300); +- +- /* Set TX Pair delay selection */ +- phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x13, 0x404); +- phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x14, 0x404); +- +- /* LED Config*/ +- mt7530_led_config_of(phydev); +- +- return 0; +-} +- +-static struct phy_driver mtk_gephy_driver[] = { +- { +- PHY_ID_MATCH_EXACT(0x03a29412), +- .name = "MediaTek MT7530 PHY", +- .config_init = mt7530_phy_config_init, +- /* Interrupts are handled by the switch, not the PHY +- * itself. +- */ +- .config_intr = genphy_no_config_intr, +- .handle_interrupt = genphy_handle_interrupt_no_ack, +- .suspend = genphy_suspend, +- .resume = genphy_resume, +- .read_page = mtk_gephy_read_page, +- .write_page = mtk_gephy_write_page, +- }, +- { +- PHY_ID_MATCH_EXACT(0x03a29441), +- .name = "MediaTek MT7531 PHY", +- .config_init = mt7531_phy_config_init, +- /* Interrupts are handled by the switch, not the PHY +- * itself. +- */ +- .config_intr = genphy_no_config_intr, +- .handle_interrupt = genphy_handle_interrupt_no_ack, +- .suspend = genphy_suspend, +- .resume = genphy_resume, +- .read_page = mtk_gephy_read_page, +- .write_page = mtk_gephy_write_page, +- }, +-}; +- +-module_phy_driver(mtk_gephy_driver); +- +-static struct mdio_device_id __maybe_unused mtk_gephy_tbl[] = { +- { PHY_ID_MATCH_EXACT(0x03a29441) }, +- { PHY_ID_MATCH_EXACT(0x03a29412) }, +- { } +-}; +- +-MODULE_DESCRIPTION("MediaTek Gigabit Ethernet PHY driver"); +-MODULE_AUTHOR("DENG, Qingfang "); +-MODULE_LICENSE("GPL"); +- +-MODULE_DEVICE_TABLE(mdio, mtk_gephy_tbl); +--- /dev/null ++++ b/drivers/net/phy/mediatek/mtk-ge-soc.c +@@ -0,0 +1,1555 @@ ++// SPDX-License-Identifier: GPL-2.0+ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define MTK_GPHY_ID_MT7981 0x03a29461 ++#define MTK_GPHY_ID_MT7988 0x03a29481 ++ ++#define MTK_EXT_PAGE_ACCESS 0x1f ++#define MTK_PHY_PAGE_STANDARD 0x0000 ++#define MTK_PHY_PAGE_EXTENDED_3 0x0003 ++ ++#define MTK_PHY_LPI_REG_14 0x14 ++#define MTK_PHY_LPI_WAKE_TIMER_1000_MASK GENMASK(8, 0) ++ ++#define MTK_PHY_LPI_REG_1c 0x1c ++#define MTK_PHY_SMI_DET_ON_THRESH_MASK GENMASK(13, 8) ++ ++#define MTK_PHY_PAGE_EXTENDED_2A30 0x2a30 ++#define MTK_PHY_PAGE_EXTENDED_52B5 0x52b5 ++ ++#define ANALOG_INTERNAL_OPERATION_MAX_US 20 ++#define TXRESERVE_MIN 0 ++#define TXRESERVE_MAX 7 ++ ++#define MTK_PHY_ANARG_RG 0x10 ++#define MTK_PHY_TCLKOFFSET_MASK GENMASK(12, 8) ++ ++/* Registers on MDIO_MMD_VEND1 */ ++#define MTK_PHY_TXVLD_DA_RG 0x12 ++#define MTK_PHY_DA_TX_I2MPB_A_GBE_MASK GENMASK(15, 10) ++#define MTK_PHY_DA_TX_I2MPB_A_TBT_MASK GENMASK(5, 0) ++ ++#define MTK_PHY_TX_I2MPB_TEST_MODE_A2 0x16 ++#define MTK_PHY_DA_TX_I2MPB_A_HBT_MASK GENMASK(15, 10) ++#define MTK_PHY_DA_TX_I2MPB_A_TST_MASK GENMASK(5, 0) ++ ++#define MTK_PHY_TX_I2MPB_TEST_MODE_B1 0x17 ++#define MTK_PHY_DA_TX_I2MPB_B_GBE_MASK GENMASK(13, 8) ++#define MTK_PHY_DA_TX_I2MPB_B_TBT_MASK GENMASK(5, 0) ++ ++#define MTK_PHY_TX_I2MPB_TEST_MODE_B2 0x18 ++#define MTK_PHY_DA_TX_I2MPB_B_HBT_MASK GENMASK(13, 8) ++#define MTK_PHY_DA_TX_I2MPB_B_TST_MASK GENMASK(5, 0) ++ ++#define MTK_PHY_TX_I2MPB_TEST_MODE_C1 0x19 ++#define MTK_PHY_DA_TX_I2MPB_C_GBE_MASK GENMASK(13, 8) ++#define MTK_PHY_DA_TX_I2MPB_C_TBT_MASK GENMASK(5, 0) ++ ++#define MTK_PHY_TX_I2MPB_TEST_MODE_C2 0x20 ++#define MTK_PHY_DA_TX_I2MPB_C_HBT_MASK GENMASK(13, 8) ++#define MTK_PHY_DA_TX_I2MPB_C_TST_MASK GENMASK(5, 0) ++ ++#define MTK_PHY_TX_I2MPB_TEST_MODE_D1 0x21 ++#define MTK_PHY_DA_TX_I2MPB_D_GBE_MASK GENMASK(13, 8) ++#define MTK_PHY_DA_TX_I2MPB_D_TBT_MASK GENMASK(5, 0) ++ ++#define MTK_PHY_TX_I2MPB_TEST_MODE_D2 0x22 ++#define MTK_PHY_DA_TX_I2MPB_D_HBT_MASK GENMASK(13, 8) ++#define MTK_PHY_DA_TX_I2MPB_D_TST_MASK GENMASK(5, 0) ++ ++#define MTK_PHY_RXADC_CTRL_RG7 0xc6 ++#define MTK_PHY_DA_AD_BUF_BIAS_LP_MASK GENMASK(9, 8) ++ ++#define MTK_PHY_RXADC_CTRL_RG9 0xc8 ++#define MTK_PHY_DA_RX_PSBN_TBT_MASK GENMASK(14, 12) ++#define MTK_PHY_DA_RX_PSBN_HBT_MASK GENMASK(10, 8) ++#define MTK_PHY_DA_RX_PSBN_GBE_MASK GENMASK(6, 4) ++#define MTK_PHY_DA_RX_PSBN_LP_MASK GENMASK(2, 0) ++ ++#define MTK_PHY_LDO_OUTPUT_V 0xd7 ++ ++#define MTK_PHY_RG_ANA_CAL_RG0 0xdb ++#define MTK_PHY_RG_CAL_CKINV BIT(12) ++#define MTK_PHY_RG_ANA_CALEN BIT(8) ++#define MTK_PHY_RG_ZCALEN_A BIT(0) ++ ++#define MTK_PHY_RG_ANA_CAL_RG1 0xdc ++#define MTK_PHY_RG_ZCALEN_B BIT(12) ++#define MTK_PHY_RG_ZCALEN_C BIT(8) ++#define MTK_PHY_RG_ZCALEN_D BIT(4) ++#define MTK_PHY_RG_TXVOS_CALEN BIT(0) ++ ++#define MTK_PHY_RG_ANA_CAL_RG5 0xe0 ++#define MTK_PHY_RG_REXT_TRIM_MASK GENMASK(13, 8) ++ ++#define MTK_PHY_RG_TX_FILTER 0xfe ++ ++#define MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG120 0x120 ++#define MTK_PHY_LPI_SIG_EN_LO_THRESH1000_MASK GENMASK(12, 8) ++#define MTK_PHY_LPI_SIG_EN_HI_THRESH1000_MASK GENMASK(4, 0) ++ ++#define MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG122 0x122 ++#define MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK GENMASK(7, 0) ++ ++#define MTK_PHY_RG_TESTMUX_ADC_CTRL 0x144 ++#define MTK_PHY_RG_TXEN_DIG_MASK GENMASK(5, 5) ++ ++#define MTK_PHY_RG_CR_TX_AMP_OFFSET_A_B 0x172 ++#define MTK_PHY_CR_TX_AMP_OFFSET_A_MASK GENMASK(13, 8) ++#define MTK_PHY_CR_TX_AMP_OFFSET_B_MASK GENMASK(6, 0) ++ ++#define MTK_PHY_RG_CR_TX_AMP_OFFSET_C_D 0x173 ++#define MTK_PHY_CR_TX_AMP_OFFSET_C_MASK GENMASK(13, 8) ++#define MTK_PHY_CR_TX_AMP_OFFSET_D_MASK GENMASK(6, 0) ++ ++#define MTK_PHY_RG_AD_CAL_COMP 0x17a ++#define MTK_PHY_AD_CAL_COMP_OUT_SHIFT (8) ++ ++#define MTK_PHY_RG_AD_CAL_CLK 0x17b ++#define MTK_PHY_DA_CAL_CLK BIT(0) ++ ++#define MTK_PHY_RG_AD_CALIN 0x17c ++#define MTK_PHY_DA_CALIN_FLAG BIT(0) ++ ++#define MTK_PHY_RG_DASN_DAC_IN0_A 0x17d ++#define MTK_PHY_DASN_DAC_IN0_A_MASK GENMASK(9, 0) ++ ++#define MTK_PHY_RG_DASN_DAC_IN0_B 0x17e ++#define MTK_PHY_DASN_DAC_IN0_B_MASK GENMASK(9, 0) ++ ++#define MTK_PHY_RG_DASN_DAC_IN0_C 0x17f ++#define MTK_PHY_DASN_DAC_IN0_C_MASK GENMASK(9, 0) ++ ++#define MTK_PHY_RG_DASN_DAC_IN0_D 0x180 ++#define MTK_PHY_DASN_DAC_IN0_D_MASK GENMASK(9, 0) ++ ++#define MTK_PHY_RG_DASN_DAC_IN1_A 0x181 ++#define MTK_PHY_DASN_DAC_IN1_A_MASK GENMASK(9, 0) ++ ++#define MTK_PHY_RG_DASN_DAC_IN1_B 0x182 ++#define MTK_PHY_DASN_DAC_IN1_B_MASK GENMASK(9, 0) ++ ++#define MTK_PHY_RG_DASN_DAC_IN1_C 0x183 ++#define MTK_PHY_DASN_DAC_IN1_C_MASK GENMASK(9, 0) ++ ++#define MTK_PHY_RG_DASN_DAC_IN1_D 0x184 ++#define MTK_PHY_DASN_DAC_IN1_D_MASK GENMASK(9, 0) ++ ++#define MTK_PHY_RG_DEV1E_REG19b 0x19b ++#define MTK_PHY_BYPASS_DSP_LPI_READY BIT(8) ++ ++#define MTK_PHY_RG_LP_IIR2_K1_L 0x22a ++#define MTK_PHY_RG_LP_IIR2_K1_U 0x22b ++#define MTK_PHY_RG_LP_IIR2_K2_L 0x22c ++#define MTK_PHY_RG_LP_IIR2_K2_U 0x22d ++#define MTK_PHY_RG_LP_IIR2_K3_L 0x22e ++#define MTK_PHY_RG_LP_IIR2_K3_U 0x22f ++#define MTK_PHY_RG_LP_IIR2_K4_L 0x230 ++#define MTK_PHY_RG_LP_IIR2_K4_U 0x231 ++#define MTK_PHY_RG_LP_IIR2_K5_L 0x232 ++#define MTK_PHY_RG_LP_IIR2_K5_U 0x233 ++ ++#define MTK_PHY_RG_DEV1E_REG234 0x234 ++#define MTK_PHY_TR_OPEN_LOOP_EN_MASK GENMASK(0, 0) ++#define MTK_PHY_LPF_X_AVERAGE_MASK GENMASK(7, 4) ++#define MTK_PHY_TR_LP_IIR_EEE_EN BIT(12) ++ ++#define MTK_PHY_RG_LPF_CNT_VAL 0x235 ++ ++#define MTK_PHY_RG_DEV1E_REG238 0x238 ++#define MTK_PHY_LPI_SLV_SEND_TX_TIMER_MASK GENMASK(8, 0) ++#define MTK_PHY_LPI_SLV_SEND_TX_EN BIT(12) ++ ++#define MTK_PHY_RG_DEV1E_REG239 0x239 ++#define MTK_PHY_LPI_SEND_LOC_TIMER_MASK GENMASK(8, 0) ++#define MTK_PHY_LPI_TXPCS_LOC_RCV BIT(12) ++ ++#define MTK_PHY_RG_DEV1E_REG27C 0x27c ++#define MTK_PHY_VGASTATE_FFE_THR_ST1_MASK GENMASK(12, 8) ++#define MTK_PHY_RG_DEV1E_REG27D 0x27d ++#define MTK_PHY_VGASTATE_FFE_THR_ST2_MASK GENMASK(4, 0) ++ ++#define MTK_PHY_RG_DEV1E_REG2C7 0x2c7 ++#define MTK_PHY_MAX_GAIN_MASK GENMASK(4, 0) ++#define MTK_PHY_MIN_GAIN_MASK GENMASK(12, 8) ++ ++#define MTK_PHY_RG_DEV1E_REG2D1 0x2d1 ++#define MTK_PHY_VCO_SLICER_THRESH_BITS_HIGH_EEE_MASK GENMASK(7, 0) ++#define MTK_PHY_LPI_SKIP_SD_SLV_TR BIT(8) ++#define MTK_PHY_LPI_TR_READY BIT(9) ++#define MTK_PHY_LPI_VCO_EEE_STG0_EN BIT(10) ++ ++#define MTK_PHY_RG_DEV1E_REG323 0x323 ++#define MTK_PHY_EEE_WAKE_MAS_INT_DC BIT(0) ++#define MTK_PHY_EEE_WAKE_SLV_INT_DC BIT(4) ++ ++#define MTK_PHY_RG_DEV1E_REG324 0x324 ++#define MTK_PHY_SMI_DETCNT_MAX_MASK GENMASK(5, 0) ++#define MTK_PHY_SMI_DET_MAX_EN BIT(8) ++ ++#define MTK_PHY_RG_DEV1E_REG326 0x326 ++#define MTK_PHY_LPI_MODE_SD_ON BIT(0) ++#define MTK_PHY_RESET_RANDUPD_CNT BIT(1) ++#define MTK_PHY_TREC_UPDATE_ENAB_CLR BIT(2) ++#define MTK_PHY_LPI_QUIT_WAIT_DFE_SIG_DET_OFF BIT(4) ++#define MTK_PHY_TR_READY_SKIP_AFE_WAKEUP BIT(5) ++ ++#define MTK_PHY_LDO_PUMP_EN_PAIRAB 0x502 ++#define MTK_PHY_LDO_PUMP_EN_PAIRCD 0x503 ++ ++#define MTK_PHY_DA_TX_R50_PAIR_A 0x53d ++#define MTK_PHY_DA_TX_R50_PAIR_B 0x53e ++#define MTK_PHY_DA_TX_R50_PAIR_C 0x53f ++#define MTK_PHY_DA_TX_R50_PAIR_D 0x540 ++ ++/* Registers on MDIO_MMD_VEND2 */ ++#define MTK_PHY_LED0_ON_CTRL 0x24 ++#define MTK_PHY_LED1_ON_CTRL 0x26 ++#define MTK_PHY_LED_ON_MASK GENMASK(6, 0) ++#define MTK_PHY_LED_ON_LINK1000 BIT(0) ++#define MTK_PHY_LED_ON_LINK100 BIT(1) ++#define MTK_PHY_LED_ON_LINK10 BIT(2) ++#define MTK_PHY_LED_ON_LINK (MTK_PHY_LED_ON_LINK10 |\ ++ MTK_PHY_LED_ON_LINK100 |\ ++ MTK_PHY_LED_ON_LINK1000) ++#define MTK_PHY_LED_ON_LINKDOWN BIT(3) ++#define MTK_PHY_LED_ON_FDX BIT(4) /* Full duplex */ ++#define MTK_PHY_LED_ON_HDX BIT(5) /* Half duplex */ ++#define MTK_PHY_LED_ON_FORCE_ON BIT(6) ++#define MTK_PHY_LED_ON_POLARITY BIT(14) ++#define MTK_PHY_LED_ON_ENABLE BIT(15) ++ ++#define MTK_PHY_LED0_BLINK_CTRL 0x25 ++#define MTK_PHY_LED1_BLINK_CTRL 0x27 ++#define MTK_PHY_LED_BLINK_1000TX BIT(0) ++#define MTK_PHY_LED_BLINK_1000RX BIT(1) ++#define MTK_PHY_LED_BLINK_100TX BIT(2) ++#define MTK_PHY_LED_BLINK_100RX BIT(3) ++#define MTK_PHY_LED_BLINK_10TX BIT(4) ++#define MTK_PHY_LED_BLINK_10RX BIT(5) ++#define MTK_PHY_LED_BLINK_RX (MTK_PHY_LED_BLINK_10RX |\ ++ MTK_PHY_LED_BLINK_100RX |\ ++ MTK_PHY_LED_BLINK_1000RX) ++#define MTK_PHY_LED_BLINK_TX (MTK_PHY_LED_BLINK_10TX |\ ++ MTK_PHY_LED_BLINK_100TX |\ ++ MTK_PHY_LED_BLINK_1000TX) ++#define MTK_PHY_LED_BLINK_COLLISION BIT(6) ++#define MTK_PHY_LED_BLINK_RX_CRC_ERR BIT(7) ++#define MTK_PHY_LED_BLINK_RX_IDLE_ERR BIT(8) ++#define MTK_PHY_LED_BLINK_FORCE_BLINK BIT(9) ++ ++#define MTK_PHY_LED1_DEFAULT_POLARITIES BIT(1) ++ ++#define MTK_PHY_RG_BG_RASEL 0x115 ++#define MTK_PHY_RG_BG_RASEL_MASK GENMASK(2, 0) ++ ++/* 'boottrap' register reflecting the configuration of the 4 PHY LEDs */ ++#define RG_GPIO_MISC_TPBANK0 0x6f0 ++#define RG_GPIO_MISC_TPBANK0_BOOTMODE GENMASK(11, 8) ++ ++/* These macro privides efuse parsing for internal phy. */ ++#define EFS_DA_TX_I2MPB_A(x) (((x) >> 0) & GENMASK(5, 0)) ++#define EFS_DA_TX_I2MPB_B(x) (((x) >> 6) & GENMASK(5, 0)) ++#define EFS_DA_TX_I2MPB_C(x) (((x) >> 12) & GENMASK(5, 0)) ++#define EFS_DA_TX_I2MPB_D(x) (((x) >> 18) & GENMASK(5, 0)) ++#define EFS_DA_TX_AMP_OFFSET_A(x) (((x) >> 24) & GENMASK(5, 0)) ++ ++#define EFS_DA_TX_AMP_OFFSET_B(x) (((x) >> 0) & GENMASK(5, 0)) ++#define EFS_DA_TX_AMP_OFFSET_C(x) (((x) >> 6) & GENMASK(5, 0)) ++#define EFS_DA_TX_AMP_OFFSET_D(x) (((x) >> 12) & GENMASK(5, 0)) ++#define EFS_DA_TX_R50_A(x) (((x) >> 18) & GENMASK(5, 0)) ++#define EFS_DA_TX_R50_B(x) (((x) >> 24) & GENMASK(5, 0)) ++ ++#define EFS_DA_TX_R50_C(x) (((x) >> 0) & GENMASK(5, 0)) ++#define EFS_DA_TX_R50_D(x) (((x) >> 6) & GENMASK(5, 0)) ++ ++#define EFS_RG_BG_RASEL(x) (((x) >> 4) & GENMASK(2, 0)) ++#define EFS_RG_REXT_TRIM(x) (((x) >> 7) & GENMASK(5, 0)) ++ ++enum { ++ NO_PAIR, ++ PAIR_A, ++ PAIR_B, ++ PAIR_C, ++ PAIR_D, ++}; ++ ++enum calibration_mode { ++ EFUSE_K, ++ SW_K ++}; ++ ++enum CAL_ITEM { ++ REXT, ++ TX_OFFSET, ++ TX_AMP, ++ TX_R50, ++ TX_VCM ++}; ++ ++enum CAL_MODE { ++ EFUSE_M, ++ SW_M ++}; ++ ++#define MTK_PHY_LED_STATE_FORCE_ON 0 ++#define MTK_PHY_LED_STATE_FORCE_BLINK 1 ++#define MTK_PHY_LED_STATE_NETDEV 2 ++ ++struct mtk_socphy_priv { ++ unsigned long led_state; ++}; ++ ++struct mtk_socphy_shared { ++ u32 boottrap; ++ struct mtk_socphy_priv priv[4]; ++}; ++ ++static int mtk_socphy_read_page(struct phy_device *phydev) ++{ ++ return __phy_read(phydev, MTK_EXT_PAGE_ACCESS); ++} ++ ++static int mtk_socphy_write_page(struct phy_device *phydev, int page) ++{ ++ return __phy_write(phydev, MTK_EXT_PAGE_ACCESS, page); ++} ++ ++/* One calibration cycle consists of: ++ * 1.Set DA_CALIN_FLAG high to start calibration. Keep it high ++ * until AD_CAL_COMP is ready to output calibration result. ++ * 2.Wait until DA_CAL_CLK is available. ++ * 3.Fetch AD_CAL_COMP_OUT. ++ */ ++static int cal_cycle(struct phy_device *phydev, int devad, ++ u32 regnum, u16 mask, u16 cal_val) ++{ ++ int reg_val; ++ int ret; ++ ++ phy_modify_mmd(phydev, devad, regnum, ++ mask, cal_val); ++ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_AD_CALIN, ++ MTK_PHY_DA_CALIN_FLAG); ++ ++ ret = phy_read_mmd_poll_timeout(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RG_AD_CAL_CLK, reg_val, ++ reg_val & MTK_PHY_DA_CAL_CLK, 500, ++ ANALOG_INTERNAL_OPERATION_MAX_US, false); ++ if (ret) { ++ phydev_err(phydev, "Calibration cycle timeout\n"); ++ return ret; ++ } ++ ++ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_AD_CALIN, ++ MTK_PHY_DA_CALIN_FLAG); ++ ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_AD_CAL_COMP) >> ++ MTK_PHY_AD_CAL_COMP_OUT_SHIFT; ++ phydev_dbg(phydev, "cal_val: 0x%x, ret: %d\n", cal_val, ret); ++ ++ return ret; ++} ++ ++static int rext_fill_result(struct phy_device *phydev, u16 *buf) ++{ ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG5, ++ MTK_PHY_RG_REXT_TRIM_MASK, buf[0] << 8); ++ phy_modify_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_RG_BG_RASEL, ++ MTK_PHY_RG_BG_RASEL_MASK, buf[1]); ++ ++ return 0; ++} ++ ++static int rext_cal_efuse(struct phy_device *phydev, u32 *buf) ++{ ++ u16 rext_cal_val[2]; ++ ++ rext_cal_val[0] = EFS_RG_REXT_TRIM(buf[3]); ++ rext_cal_val[1] = EFS_RG_BG_RASEL(buf[3]); ++ rext_fill_result(phydev, rext_cal_val); ++ ++ return 0; ++} ++ ++static int tx_offset_fill_result(struct phy_device *phydev, u16 *buf) ++{ ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_CR_TX_AMP_OFFSET_A_B, ++ MTK_PHY_CR_TX_AMP_OFFSET_A_MASK, buf[0] << 8); ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_CR_TX_AMP_OFFSET_A_B, ++ MTK_PHY_CR_TX_AMP_OFFSET_B_MASK, buf[1]); ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_CR_TX_AMP_OFFSET_C_D, ++ MTK_PHY_CR_TX_AMP_OFFSET_C_MASK, buf[2] << 8); ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_CR_TX_AMP_OFFSET_C_D, ++ MTK_PHY_CR_TX_AMP_OFFSET_D_MASK, buf[3]); ++ ++ return 0; ++} ++ ++static int tx_offset_cal_efuse(struct phy_device *phydev, u32 *buf) ++{ ++ u16 tx_offset_cal_val[4]; ++ ++ tx_offset_cal_val[0] = EFS_DA_TX_AMP_OFFSET_A(buf[0]); ++ tx_offset_cal_val[1] = EFS_DA_TX_AMP_OFFSET_B(buf[1]); ++ tx_offset_cal_val[2] = EFS_DA_TX_AMP_OFFSET_C(buf[1]); ++ tx_offset_cal_val[3] = EFS_DA_TX_AMP_OFFSET_D(buf[1]); ++ ++ tx_offset_fill_result(phydev, tx_offset_cal_val); ++ ++ return 0; ++} ++ ++static int tx_amp_fill_result(struct phy_device *phydev, u16 *buf) ++{ ++ int i; ++ int bias[16] = {}; ++ const int vals_9461[16] = { 7, 1, 4, 7, ++ 7, 1, 4, 7, ++ 7, 1, 4, 7, ++ 7, 1, 4, 7 }; ++ const int vals_9481[16] = { 10, 6, 6, 10, ++ 10, 6, 6, 10, ++ 10, 6, 6, 10, ++ 10, 6, 6, 10 }; ++ switch (phydev->drv->phy_id) { ++ case MTK_GPHY_ID_MT7981: ++ /* We add some calibration to efuse values ++ * due to board level influence. ++ * GBE: +7, TBT: +1, HBT: +4, TST: +7 ++ */ ++ memcpy(bias, (const void *)vals_9461, sizeof(bias)); ++ break; ++ case MTK_GPHY_ID_MT7988: ++ memcpy(bias, (const void *)vals_9481, sizeof(bias)); ++ break; ++ } ++ ++ /* Prevent overflow */ ++ for (i = 0; i < 12; i++) { ++ if (buf[i >> 2] + bias[i] > 63) { ++ buf[i >> 2] = 63; ++ bias[i] = 0; ++ } ++ } ++ ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TXVLD_DA_RG, ++ MTK_PHY_DA_TX_I2MPB_A_GBE_MASK, (buf[0] + bias[0]) << 10); ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TXVLD_DA_RG, ++ MTK_PHY_DA_TX_I2MPB_A_TBT_MASK, buf[0] + bias[1]); ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_A2, ++ MTK_PHY_DA_TX_I2MPB_A_HBT_MASK, (buf[0] + bias[2]) << 10); ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_A2, ++ MTK_PHY_DA_TX_I2MPB_A_TST_MASK, buf[0] + bias[3]); ++ ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_B1, ++ MTK_PHY_DA_TX_I2MPB_B_GBE_MASK, (buf[1] + bias[4]) << 8); ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_B1, ++ MTK_PHY_DA_TX_I2MPB_B_TBT_MASK, buf[1] + bias[5]); ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_B2, ++ MTK_PHY_DA_TX_I2MPB_B_HBT_MASK, (buf[1] + bias[6]) << 8); ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_B2, ++ MTK_PHY_DA_TX_I2MPB_B_TST_MASK, buf[1] + bias[7]); ++ ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_C1, ++ MTK_PHY_DA_TX_I2MPB_C_GBE_MASK, (buf[2] + bias[8]) << 8); ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_C1, ++ MTK_PHY_DA_TX_I2MPB_C_TBT_MASK, buf[2] + bias[9]); ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_C2, ++ MTK_PHY_DA_TX_I2MPB_C_HBT_MASK, (buf[2] + bias[10]) << 8); ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_C2, ++ MTK_PHY_DA_TX_I2MPB_C_TST_MASK, buf[2] + bias[11]); ++ ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_D1, ++ MTK_PHY_DA_TX_I2MPB_D_GBE_MASK, (buf[3] + bias[12]) << 8); ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_D1, ++ MTK_PHY_DA_TX_I2MPB_D_TBT_MASK, buf[3] + bias[13]); ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_D2, ++ MTK_PHY_DA_TX_I2MPB_D_HBT_MASK, (buf[3] + bias[14]) << 8); ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_D2, ++ MTK_PHY_DA_TX_I2MPB_D_TST_MASK, buf[3] + bias[15]); ++ ++ return 0; ++} ++ ++static int tx_amp_cal_efuse(struct phy_device *phydev, u32 *buf) ++{ ++ u16 tx_amp_cal_val[4]; ++ ++ tx_amp_cal_val[0] = EFS_DA_TX_I2MPB_A(buf[0]); ++ tx_amp_cal_val[1] = EFS_DA_TX_I2MPB_B(buf[0]); ++ tx_amp_cal_val[2] = EFS_DA_TX_I2MPB_C(buf[0]); ++ tx_amp_cal_val[3] = EFS_DA_TX_I2MPB_D(buf[0]); ++ tx_amp_fill_result(phydev, tx_amp_cal_val); ++ ++ return 0; ++} ++ ++static int tx_r50_fill_result(struct phy_device *phydev, u16 tx_r50_cal_val, ++ u8 txg_calen_x) ++{ ++ int bias = 0; ++ u16 reg, val; ++ ++ if (phydev->drv->phy_id == MTK_GPHY_ID_MT7988) ++ bias = -1; ++ ++ val = clamp_val(bias + tx_r50_cal_val, 0, 63); ++ ++ switch (txg_calen_x) { ++ case PAIR_A: ++ reg = MTK_PHY_DA_TX_R50_PAIR_A; ++ break; ++ case PAIR_B: ++ reg = MTK_PHY_DA_TX_R50_PAIR_B; ++ break; ++ case PAIR_C: ++ reg = MTK_PHY_DA_TX_R50_PAIR_C; ++ break; ++ case PAIR_D: ++ reg = MTK_PHY_DA_TX_R50_PAIR_D; ++ break; ++ default: ++ return -EINVAL; ++ } ++ ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, reg, val | val << 8); ++ ++ return 0; ++} ++ ++static int tx_r50_cal_efuse(struct phy_device *phydev, u32 *buf, ++ u8 txg_calen_x) ++{ ++ u16 tx_r50_cal_val; ++ ++ switch (txg_calen_x) { ++ case PAIR_A: ++ tx_r50_cal_val = EFS_DA_TX_R50_A(buf[1]); ++ break; ++ case PAIR_B: ++ tx_r50_cal_val = EFS_DA_TX_R50_B(buf[1]); ++ break; ++ case PAIR_C: ++ tx_r50_cal_val = EFS_DA_TX_R50_C(buf[2]); ++ break; ++ case PAIR_D: ++ tx_r50_cal_val = EFS_DA_TX_R50_D(buf[2]); ++ break; ++ default: ++ return -EINVAL; ++ } ++ tx_r50_fill_result(phydev, tx_r50_cal_val, txg_calen_x); ++ ++ return 0; ++} ++ ++static int tx_vcm_cal_sw(struct phy_device *phydev, u8 rg_txreserve_x) ++{ ++ u8 lower_idx, upper_idx, txreserve_val; ++ u8 lower_ret, upper_ret; ++ int ret; ++ ++ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG0, ++ MTK_PHY_RG_ANA_CALEN); ++ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG0, ++ MTK_PHY_RG_CAL_CKINV); ++ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG1, ++ MTK_PHY_RG_TXVOS_CALEN); ++ ++ switch (rg_txreserve_x) { ++ case PAIR_A: ++ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RG_DASN_DAC_IN0_A, ++ MTK_PHY_DASN_DAC_IN0_A_MASK); ++ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RG_DASN_DAC_IN1_A, ++ MTK_PHY_DASN_DAC_IN1_A_MASK); ++ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RG_ANA_CAL_RG0, ++ MTK_PHY_RG_ZCALEN_A); ++ break; ++ case PAIR_B: ++ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RG_DASN_DAC_IN0_B, ++ MTK_PHY_DASN_DAC_IN0_B_MASK); ++ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RG_DASN_DAC_IN1_B, ++ MTK_PHY_DASN_DAC_IN1_B_MASK); ++ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RG_ANA_CAL_RG1, ++ MTK_PHY_RG_ZCALEN_B); ++ break; ++ case PAIR_C: ++ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RG_DASN_DAC_IN0_C, ++ MTK_PHY_DASN_DAC_IN0_C_MASK); ++ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RG_DASN_DAC_IN1_C, ++ MTK_PHY_DASN_DAC_IN1_C_MASK); ++ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RG_ANA_CAL_RG1, ++ MTK_PHY_RG_ZCALEN_C); ++ break; ++ case PAIR_D: ++ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RG_DASN_DAC_IN0_D, ++ MTK_PHY_DASN_DAC_IN0_D_MASK); ++ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RG_DASN_DAC_IN1_D, ++ MTK_PHY_DASN_DAC_IN1_D_MASK); ++ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RG_ANA_CAL_RG1, ++ MTK_PHY_RG_ZCALEN_D); ++ break; ++ default: ++ ret = -EINVAL; ++ goto restore; ++ } ++ ++ lower_idx = TXRESERVE_MIN; ++ upper_idx = TXRESERVE_MAX; ++ ++ phydev_dbg(phydev, "Start TX-VCM SW cal.\n"); ++ while ((upper_idx - lower_idx) > 1) { ++ txreserve_val = DIV_ROUND_CLOSEST(lower_idx + upper_idx, 2); ++ ret = cal_cycle(phydev, MDIO_MMD_VEND1, MTK_PHY_RXADC_CTRL_RG9, ++ MTK_PHY_DA_RX_PSBN_TBT_MASK | ++ MTK_PHY_DA_RX_PSBN_HBT_MASK | ++ MTK_PHY_DA_RX_PSBN_GBE_MASK | ++ MTK_PHY_DA_RX_PSBN_LP_MASK, ++ txreserve_val << 12 | txreserve_val << 8 | ++ txreserve_val << 4 | txreserve_val); ++ if (ret == 1) { ++ upper_idx = txreserve_val; ++ upper_ret = ret; ++ } else if (ret == 0) { ++ lower_idx = txreserve_val; ++ lower_ret = ret; ++ } else { ++ goto restore; ++ } ++ } ++ ++ if (lower_idx == TXRESERVE_MIN) { ++ lower_ret = cal_cycle(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RXADC_CTRL_RG9, ++ MTK_PHY_DA_RX_PSBN_TBT_MASK | ++ MTK_PHY_DA_RX_PSBN_HBT_MASK | ++ MTK_PHY_DA_RX_PSBN_GBE_MASK | ++ MTK_PHY_DA_RX_PSBN_LP_MASK, ++ lower_idx << 12 | lower_idx << 8 | ++ lower_idx << 4 | lower_idx); ++ ret = lower_ret; ++ } else if (upper_idx == TXRESERVE_MAX) { ++ upper_ret = cal_cycle(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RXADC_CTRL_RG9, ++ MTK_PHY_DA_RX_PSBN_TBT_MASK | ++ MTK_PHY_DA_RX_PSBN_HBT_MASK | ++ MTK_PHY_DA_RX_PSBN_GBE_MASK | ++ MTK_PHY_DA_RX_PSBN_LP_MASK, ++ upper_idx << 12 | upper_idx << 8 | ++ upper_idx << 4 | upper_idx); ++ ret = upper_ret; ++ } ++ if (ret < 0) ++ goto restore; ++ ++ /* We calibrate TX-VCM in different logic. Check upper index and then ++ * lower index. If this calibration is valid, apply lower index's result. ++ */ ++ ret = upper_ret - lower_ret; ++ if (ret == 1) { ++ ret = 0; ++ /* Make sure we use upper_idx in our calibration system */ ++ cal_cycle(phydev, MDIO_MMD_VEND1, MTK_PHY_RXADC_CTRL_RG9, ++ MTK_PHY_DA_RX_PSBN_TBT_MASK | ++ MTK_PHY_DA_RX_PSBN_HBT_MASK | ++ MTK_PHY_DA_RX_PSBN_GBE_MASK | ++ MTK_PHY_DA_RX_PSBN_LP_MASK, ++ upper_idx << 12 | upper_idx << 8 | ++ upper_idx << 4 | upper_idx); ++ phydev_dbg(phydev, "TX-VCM SW cal result: 0x%x\n", upper_idx); ++ } else if (lower_idx == TXRESERVE_MIN && upper_ret == 1 && ++ lower_ret == 1) { ++ ret = 0; ++ cal_cycle(phydev, MDIO_MMD_VEND1, MTK_PHY_RXADC_CTRL_RG9, ++ MTK_PHY_DA_RX_PSBN_TBT_MASK | ++ MTK_PHY_DA_RX_PSBN_HBT_MASK | ++ MTK_PHY_DA_RX_PSBN_GBE_MASK | ++ MTK_PHY_DA_RX_PSBN_LP_MASK, ++ lower_idx << 12 | lower_idx << 8 | ++ lower_idx << 4 | lower_idx); ++ phydev_warn(phydev, "TX-VCM SW cal result at low margin 0x%x\n", ++ lower_idx); ++ } else if (upper_idx == TXRESERVE_MAX && upper_ret == 0 && ++ lower_ret == 0) { ++ ret = 0; ++ phydev_warn(phydev, "TX-VCM SW cal result at high margin 0x%x\n", ++ upper_idx); ++ } else { ++ ret = -EINVAL; ++ } ++ ++restore: ++ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG0, ++ MTK_PHY_RG_ANA_CALEN); ++ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG1, ++ MTK_PHY_RG_TXVOS_CALEN); ++ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG0, ++ MTK_PHY_RG_ZCALEN_A); ++ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG1, ++ MTK_PHY_RG_ZCALEN_B | MTK_PHY_RG_ZCALEN_C | ++ MTK_PHY_RG_ZCALEN_D); ++ ++ return ret; ++} ++ ++static void mt798x_phy_common_finetune(struct phy_device *phydev) ++{ ++ phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); ++ /* SlvDSPreadyTime = 24, MasDSPreadyTime = 24 */ ++ __phy_write(phydev, 0x11, 0xc71); ++ __phy_write(phydev, 0x12, 0xc); ++ __phy_write(phydev, 0x10, 0x8fae); ++ ++ /* EnabRandUpdTrig = 1 */ ++ __phy_write(phydev, 0x11, 0x2f00); ++ __phy_write(phydev, 0x12, 0xe); ++ __phy_write(phydev, 0x10, 0x8fb0); ++ ++ /* NormMseLoThresh = 85 */ ++ __phy_write(phydev, 0x11, 0x55a0); ++ __phy_write(phydev, 0x12, 0x0); ++ __phy_write(phydev, 0x10, 0x83aa); ++ ++ /* FfeUpdGainForce = 1(Enable), FfeUpdGainForceVal = 4 */ ++ __phy_write(phydev, 0x11, 0x240); ++ __phy_write(phydev, 0x12, 0x0); ++ __phy_write(phydev, 0x10, 0x9680); ++ ++ /* TrFreeze = 0 (mt7988 default) */ ++ __phy_write(phydev, 0x11, 0x0); ++ __phy_write(phydev, 0x12, 0x0); ++ __phy_write(phydev, 0x10, 0x9686); ++ ++ /* SSTrKp100 = 5 */ ++ /* SSTrKf100 = 6 */ ++ /* SSTrKp1000Mas = 5 */ ++ /* SSTrKf1000Mas = 6 */ ++ /* SSTrKp1000Slv = 5 */ ++ /* SSTrKf1000Slv = 6 */ ++ __phy_write(phydev, 0x11, 0xbaef); ++ __phy_write(phydev, 0x12, 0x2e); ++ __phy_write(phydev, 0x10, 0x968c); ++ phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); ++} ++ ++static void mt7981_phy_finetune(struct phy_device *phydev) ++{ ++ u16 val[8] = { 0x01ce, 0x01c1, ++ 0x020f, 0x0202, ++ 0x03d0, 0x03c0, ++ 0x0013, 0x0005 }; ++ int i, k; ++ ++ /* 100M eye finetune: ++ * Keep middle level of TX MLT3 shapper as default. ++ * Only change TX MLT3 overshoot level here. ++ */ ++ for (k = 0, i = 1; i < 12; i++) { ++ if (i % 3 == 0) ++ continue; ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, i, val[k++]); ++ } ++ ++ phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); ++ /* ResetSyncOffset = 6 */ ++ __phy_write(phydev, 0x11, 0x600); ++ __phy_write(phydev, 0x12, 0x0); ++ __phy_write(phydev, 0x10, 0x8fc0); ++ ++ /* VgaDecRate = 1 */ ++ __phy_write(phydev, 0x11, 0x4c2a); ++ __phy_write(phydev, 0x12, 0x3e); ++ __phy_write(phydev, 0x10, 0x8fa4); ++ ++ /* MrvlTrFix100Kp = 3, MrvlTrFix100Kf = 2, ++ * MrvlTrFix1000Kp = 3, MrvlTrFix1000Kf = 2 ++ */ ++ __phy_write(phydev, 0x11, 0xd10a); ++ __phy_write(phydev, 0x12, 0x34); ++ __phy_write(phydev, 0x10, 0x8f82); ++ ++ /* VcoSlicerThreshBitsHigh */ ++ __phy_write(phydev, 0x11, 0x5555); ++ __phy_write(phydev, 0x12, 0x55); ++ __phy_write(phydev, 0x10, 0x8ec0); ++ phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); ++ ++ /* TR_OPEN_LOOP_EN = 1, lpf_x_average = 9 */ ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG234, ++ MTK_PHY_TR_OPEN_LOOP_EN_MASK | MTK_PHY_LPF_X_AVERAGE_MASK, ++ BIT(0) | FIELD_PREP(MTK_PHY_LPF_X_AVERAGE_MASK, 0x9)); ++ ++ /* rg_tr_lpf_cnt_val = 512 */ ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LPF_CNT_VAL, 0x200); ++ ++ /* IIR2 related */ ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K1_L, 0x82); ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K1_U, 0x0); ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K2_L, 0x103); ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K2_U, 0x0); ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K3_L, 0x82); ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K3_U, 0x0); ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K4_L, 0xd177); ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K4_U, 0x3); ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K5_L, 0x2c82); ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K5_U, 0xe); ++ ++ /* FFE peaking */ ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG27C, ++ MTK_PHY_VGASTATE_FFE_THR_ST1_MASK, 0x1b << 8); ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG27D, ++ MTK_PHY_VGASTATE_FFE_THR_ST2_MASK, 0x1e); ++ ++ /* Disable LDO pump */ ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_LDO_PUMP_EN_PAIRAB, 0x0); ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_LDO_PUMP_EN_PAIRCD, 0x0); ++ /* Adjust LDO output voltage */ ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_LDO_OUTPUT_V, 0x2222); ++} ++ ++static void mt7988_phy_finetune(struct phy_device *phydev) ++{ ++ u16 val[12] = { 0x0187, 0x01cd, 0x01c8, 0x0182, ++ 0x020d, 0x0206, 0x0384, 0x03d0, ++ 0x03c6, 0x030a, 0x0011, 0x0005 }; ++ int i; ++ ++ /* Set default MLT3 shaper first */ ++ for (i = 0; i < 12; i++) ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, i, val[i]); ++ ++ /* TCT finetune */ ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_TX_FILTER, 0x5); ++ ++ phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); ++ /* ResetSyncOffset = 5 */ ++ __phy_write(phydev, 0x11, 0x500); ++ __phy_write(phydev, 0x12, 0x0); ++ __phy_write(phydev, 0x10, 0x8fc0); ++ ++ /* VgaDecRate is 1 at default on mt7988 */ ++ ++ /* MrvlTrFix100Kp = 6, MrvlTrFix100Kf = 7, ++ * MrvlTrFix1000Kp = 6, MrvlTrFix1000Kf = 7 ++ */ ++ __phy_write(phydev, 0x11, 0xb90a); ++ __phy_write(phydev, 0x12, 0x6f); ++ __phy_write(phydev, 0x10, 0x8f82); ++ ++ /* RemAckCntLimitCtrl = 1 */ ++ __phy_write(phydev, 0x11, 0xfbba); ++ __phy_write(phydev, 0x12, 0xc3); ++ __phy_write(phydev, 0x10, 0x87f8); ++ ++ phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); ++ ++ /* TR_OPEN_LOOP_EN = 1, lpf_x_average = 10 */ ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG234, ++ MTK_PHY_TR_OPEN_LOOP_EN_MASK | MTK_PHY_LPF_X_AVERAGE_MASK, ++ BIT(0) | FIELD_PREP(MTK_PHY_LPF_X_AVERAGE_MASK, 0xa)); ++ ++ /* rg_tr_lpf_cnt_val = 1023 */ ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LPF_CNT_VAL, 0x3ff); ++} ++ ++static void mt798x_phy_eee(struct phy_device *phydev) ++{ ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG120, ++ MTK_PHY_LPI_SIG_EN_LO_THRESH1000_MASK | ++ MTK_PHY_LPI_SIG_EN_HI_THRESH1000_MASK, ++ FIELD_PREP(MTK_PHY_LPI_SIG_EN_LO_THRESH1000_MASK, 0x0) | ++ FIELD_PREP(MTK_PHY_LPI_SIG_EN_HI_THRESH1000_MASK, 0x14)); ++ ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG122, ++ MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK, ++ FIELD_PREP(MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK, ++ 0xff)); ++ ++ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RG_TESTMUX_ADC_CTRL, ++ MTK_PHY_RG_TXEN_DIG_MASK); ++ ++ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RG_DEV1E_REG19b, MTK_PHY_BYPASS_DSP_LPI_READY); ++ ++ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RG_DEV1E_REG234, MTK_PHY_TR_LP_IIR_EEE_EN); ++ ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG238, ++ MTK_PHY_LPI_SLV_SEND_TX_TIMER_MASK | ++ MTK_PHY_LPI_SLV_SEND_TX_EN, ++ FIELD_PREP(MTK_PHY_LPI_SLV_SEND_TX_TIMER_MASK, 0x120)); ++ ++ /* Keep MTK_PHY_LPI_SEND_LOC_TIMER as 375 */ ++ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG239, ++ MTK_PHY_LPI_TXPCS_LOC_RCV); ++ ++ /* This also fixes some IoT issues, such as CH340 */ ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG2C7, ++ MTK_PHY_MAX_GAIN_MASK | MTK_PHY_MIN_GAIN_MASK, ++ FIELD_PREP(MTK_PHY_MAX_GAIN_MASK, 0x8) | ++ FIELD_PREP(MTK_PHY_MIN_GAIN_MASK, 0x13)); ++ ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG2D1, ++ MTK_PHY_VCO_SLICER_THRESH_BITS_HIGH_EEE_MASK, ++ FIELD_PREP(MTK_PHY_VCO_SLICER_THRESH_BITS_HIGH_EEE_MASK, ++ 0x33) | ++ MTK_PHY_LPI_SKIP_SD_SLV_TR | MTK_PHY_LPI_TR_READY | ++ MTK_PHY_LPI_VCO_EEE_STG0_EN); ++ ++ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG323, ++ MTK_PHY_EEE_WAKE_MAS_INT_DC | ++ MTK_PHY_EEE_WAKE_SLV_INT_DC); ++ ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG324, ++ MTK_PHY_SMI_DETCNT_MAX_MASK, ++ FIELD_PREP(MTK_PHY_SMI_DETCNT_MAX_MASK, 0x3f) | ++ MTK_PHY_SMI_DET_MAX_EN); ++ ++ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG326, ++ MTK_PHY_LPI_MODE_SD_ON | MTK_PHY_RESET_RANDUPD_CNT | ++ MTK_PHY_TREC_UPDATE_ENAB_CLR | ++ MTK_PHY_LPI_QUIT_WAIT_DFE_SIG_DET_OFF | ++ MTK_PHY_TR_READY_SKIP_AFE_WAKEUP); ++ ++ phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); ++ /* Regsigdet_sel_1000 = 0 */ ++ __phy_write(phydev, 0x11, 0xb); ++ __phy_write(phydev, 0x12, 0x0); ++ __phy_write(phydev, 0x10, 0x9690); ++ ++ /* REG_EEE_st2TrKf1000 = 2 */ ++ __phy_write(phydev, 0x11, 0x114f); ++ __phy_write(phydev, 0x12, 0x2); ++ __phy_write(phydev, 0x10, 0x969a); ++ ++ /* RegEEE_slv_wake_tr_timer_tar = 6, RegEEE_slv_remtx_timer_tar = 20 */ ++ __phy_write(phydev, 0x11, 0x3028); ++ __phy_write(phydev, 0x12, 0x0); ++ __phy_write(phydev, 0x10, 0x969e); ++ ++ /* RegEEE_slv_wake_int_timer_tar = 8 */ ++ __phy_write(phydev, 0x11, 0x5010); ++ __phy_write(phydev, 0x12, 0x0); ++ __phy_write(phydev, 0x10, 0x96a0); ++ ++ /* RegEEE_trfreeze_timer2 = 586 */ ++ __phy_write(phydev, 0x11, 0x24a); ++ __phy_write(phydev, 0x12, 0x0); ++ __phy_write(phydev, 0x10, 0x96a8); ++ ++ /* RegEEE100Stg1_tar = 16 */ ++ __phy_write(phydev, 0x11, 0x3210); ++ __phy_write(phydev, 0x12, 0x0); ++ __phy_write(phydev, 0x10, 0x96b8); ++ ++ /* REGEEE_wake_slv_tr_wait_dfesigdet_en = 0 */ ++ __phy_write(phydev, 0x11, 0x1463); ++ __phy_write(phydev, 0x12, 0x0); ++ __phy_write(phydev, 0x10, 0x96ca); ++ ++ /* DfeTailEnableVgaThresh1000 = 27 */ ++ __phy_write(phydev, 0x11, 0x36); ++ __phy_write(phydev, 0x12, 0x0); ++ __phy_write(phydev, 0x10, 0x8f80); ++ phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); ++ ++ phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_3); ++ __phy_modify(phydev, MTK_PHY_LPI_REG_14, MTK_PHY_LPI_WAKE_TIMER_1000_MASK, ++ FIELD_PREP(MTK_PHY_LPI_WAKE_TIMER_1000_MASK, 0x19c)); ++ ++ __phy_modify(phydev, MTK_PHY_LPI_REG_1c, MTK_PHY_SMI_DET_ON_THRESH_MASK, ++ FIELD_PREP(MTK_PHY_SMI_DET_ON_THRESH_MASK, 0xc)); ++ phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); ++ ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG122, ++ MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK, ++ FIELD_PREP(MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK, 0xff)); ++} ++ ++static int cal_sw(struct phy_device *phydev, enum CAL_ITEM cal_item, ++ u8 start_pair, u8 end_pair) ++{ ++ u8 pair_n; ++ int ret; ++ ++ for (pair_n = start_pair; pair_n <= end_pair; pair_n++) { ++ /* TX_OFFSET & TX_AMP have no SW calibration. */ ++ switch (cal_item) { ++ case TX_VCM: ++ ret = tx_vcm_cal_sw(phydev, pair_n); ++ break; ++ default: ++ return -EINVAL; ++ } ++ if (ret) ++ return ret; ++ } ++ return 0; ++} ++ ++static int cal_efuse(struct phy_device *phydev, enum CAL_ITEM cal_item, ++ u8 start_pair, u8 end_pair, u32 *buf) ++{ ++ u8 pair_n; ++ int ret; ++ ++ for (pair_n = start_pair; pair_n <= end_pair; pair_n++) { ++ /* TX_VCM has no efuse calibration. */ ++ switch (cal_item) { ++ case REXT: ++ ret = rext_cal_efuse(phydev, buf); ++ break; ++ case TX_OFFSET: ++ ret = tx_offset_cal_efuse(phydev, buf); ++ break; ++ case TX_AMP: ++ ret = tx_amp_cal_efuse(phydev, buf); ++ break; ++ case TX_R50: ++ ret = tx_r50_cal_efuse(phydev, buf, pair_n); ++ break; ++ default: ++ return -EINVAL; ++ } ++ if (ret) ++ return ret; ++ } ++ ++ return 0; ++} ++ ++static int start_cal(struct phy_device *phydev, enum CAL_ITEM cal_item, ++ enum CAL_MODE cal_mode, u8 start_pair, ++ u8 end_pair, u32 *buf) ++{ ++ int ret; ++ ++ switch (cal_mode) { ++ case EFUSE_M: ++ ret = cal_efuse(phydev, cal_item, start_pair, ++ end_pair, buf); ++ break; ++ case SW_M: ++ ret = cal_sw(phydev, cal_item, start_pair, end_pair); ++ break; ++ default: ++ return -EINVAL; ++ } ++ ++ if (ret) { ++ phydev_err(phydev, "cal %d failed\n", cal_item); ++ return -EIO; ++ } ++ ++ return 0; ++} ++ ++static int mt798x_phy_calibration(struct phy_device *phydev) ++{ ++ int ret = 0; ++ u32 *buf; ++ size_t len; ++ struct nvmem_cell *cell; ++ ++ cell = nvmem_cell_get(&phydev->mdio.dev, "phy-cal-data"); ++ if (IS_ERR(cell)) { ++ if (PTR_ERR(cell) == -EPROBE_DEFER) ++ return PTR_ERR(cell); ++ return 0; ++ } ++ ++ buf = (u32 *)nvmem_cell_read(cell, &len); ++ if (IS_ERR(buf)) ++ return PTR_ERR(buf); ++ nvmem_cell_put(cell); ++ ++ if (!buf[0] || !buf[1] || !buf[2] || !buf[3] || len < 4 * sizeof(u32)) { ++ phydev_err(phydev, "invalid efuse data\n"); ++ ret = -EINVAL; ++ goto out; ++ } ++ ++ ret = start_cal(phydev, REXT, EFUSE_M, NO_PAIR, NO_PAIR, buf); ++ if (ret) ++ goto out; ++ ret = start_cal(phydev, TX_OFFSET, EFUSE_M, NO_PAIR, NO_PAIR, buf); ++ if (ret) ++ goto out; ++ ret = start_cal(phydev, TX_AMP, EFUSE_M, NO_PAIR, NO_PAIR, buf); ++ if (ret) ++ goto out; ++ ret = start_cal(phydev, TX_R50, EFUSE_M, PAIR_A, PAIR_D, buf); ++ if (ret) ++ goto out; ++ ret = start_cal(phydev, TX_VCM, SW_M, PAIR_A, PAIR_A, buf); ++ if (ret) ++ goto out; ++ ++out: ++ kfree(buf); ++ return ret; ++} ++ ++static int mt798x_phy_config_init(struct phy_device *phydev) ++{ ++ switch (phydev->drv->phy_id) { ++ case MTK_GPHY_ID_MT7981: ++ mt7981_phy_finetune(phydev); ++ break; ++ case MTK_GPHY_ID_MT7988: ++ mt7988_phy_finetune(phydev); ++ break; ++ } ++ ++ mt798x_phy_common_finetune(phydev); ++ mt798x_phy_eee(phydev); ++ ++ return mt798x_phy_calibration(phydev); ++} ++ ++static int mt798x_phy_hw_led_on_set(struct phy_device *phydev, u8 index, ++ bool on) ++{ ++ unsigned int bit_on = MTK_PHY_LED_STATE_FORCE_ON + (index ? 16 : 0); ++ struct mtk_socphy_priv *priv = phydev->priv; ++ bool changed; ++ ++ if (on) ++ changed = !test_and_set_bit(bit_on, &priv->led_state); ++ else ++ changed = !!test_and_clear_bit(bit_on, &priv->led_state); ++ ++ changed |= !!test_and_clear_bit(MTK_PHY_LED_STATE_NETDEV + ++ (index ? 16 : 0), &priv->led_state); ++ if (changed) ++ return phy_modify_mmd(phydev, MDIO_MMD_VEND2, index ? ++ MTK_PHY_LED1_ON_CTRL : MTK_PHY_LED0_ON_CTRL, ++ MTK_PHY_LED_ON_MASK, ++ on ? MTK_PHY_LED_ON_FORCE_ON : 0); ++ else ++ return 0; ++} ++ ++static int mt798x_phy_hw_led_blink_set(struct phy_device *phydev, u8 index, ++ bool blinking) ++{ ++ unsigned int bit_blink = MTK_PHY_LED_STATE_FORCE_BLINK + (index ? 16 : 0); ++ struct mtk_socphy_priv *priv = phydev->priv; ++ bool changed; ++ ++ if (blinking) ++ changed = !test_and_set_bit(bit_blink, &priv->led_state); ++ else ++ changed = !!test_and_clear_bit(bit_blink, &priv->led_state); ++ ++ changed |= !!test_bit(MTK_PHY_LED_STATE_NETDEV + ++ (index ? 16 : 0), &priv->led_state); ++ if (changed) ++ return phy_write_mmd(phydev, MDIO_MMD_VEND2, index ? ++ MTK_PHY_LED1_BLINK_CTRL : MTK_PHY_LED0_BLINK_CTRL, ++ blinking ? MTK_PHY_LED_BLINK_FORCE_BLINK : 0); ++ else ++ return 0; ++} ++ ++static int mt798x_phy_led_blink_set(struct phy_device *phydev, u8 index, ++ unsigned long *delay_on, ++ unsigned long *delay_off) ++{ ++ bool blinking = false; ++ int err = 0; ++ ++ if (index > 1) ++ return -EINVAL; ++ ++ if (delay_on && delay_off && (*delay_on > 0) && (*delay_off > 0)) { ++ blinking = true; ++ *delay_on = 50; ++ *delay_off = 50; ++ } ++ ++ err = mt798x_phy_hw_led_blink_set(phydev, index, blinking); ++ if (err) ++ return err; ++ ++ return mt798x_phy_hw_led_on_set(phydev, index, false); ++} ++ ++static int mt798x_phy_led_brightness_set(struct phy_device *phydev, ++ u8 index, enum led_brightness value) ++{ ++ int err; ++ ++ err = mt798x_phy_hw_led_blink_set(phydev, index, false); ++ if (err) ++ return err; ++ ++ return mt798x_phy_hw_led_on_set(phydev, index, (value != LED_OFF)); ++} ++ ++static const unsigned long supported_triggers = (BIT(TRIGGER_NETDEV_FULL_DUPLEX) | ++ BIT(TRIGGER_NETDEV_HALF_DUPLEX) | ++ BIT(TRIGGER_NETDEV_LINK) | ++ BIT(TRIGGER_NETDEV_LINK_10) | ++ BIT(TRIGGER_NETDEV_LINK_100) | ++ BIT(TRIGGER_NETDEV_LINK_1000) | ++ BIT(TRIGGER_NETDEV_RX) | ++ BIT(TRIGGER_NETDEV_TX)); ++ ++static int mt798x_phy_led_hw_is_supported(struct phy_device *phydev, u8 index, ++ unsigned long rules) ++{ ++ if (index > 1) ++ return -EINVAL; ++ ++ /* All combinations of the supported triggers are allowed */ ++ if (rules & ~supported_triggers) ++ return -EOPNOTSUPP; ++ ++ return 0; ++}; ++ ++static int mt798x_phy_led_hw_control_get(struct phy_device *phydev, u8 index, ++ unsigned long *rules) ++{ ++ unsigned int bit_blink = MTK_PHY_LED_STATE_FORCE_BLINK + (index ? 16 : 0); ++ unsigned int bit_netdev = MTK_PHY_LED_STATE_NETDEV + (index ? 16 : 0); ++ unsigned int bit_on = MTK_PHY_LED_STATE_FORCE_ON + (index ? 16 : 0); ++ struct mtk_socphy_priv *priv = phydev->priv; ++ int on, blink; ++ ++ if (index > 1) ++ return -EINVAL; ++ ++ on = phy_read_mmd(phydev, MDIO_MMD_VEND2, ++ index ? MTK_PHY_LED1_ON_CTRL : MTK_PHY_LED0_ON_CTRL); ++ ++ if (on < 0) ++ return -EIO; ++ ++ blink = phy_read_mmd(phydev, MDIO_MMD_VEND2, ++ index ? MTK_PHY_LED1_BLINK_CTRL : ++ MTK_PHY_LED0_BLINK_CTRL); ++ if (blink < 0) ++ return -EIO; ++ ++ if ((on & (MTK_PHY_LED_ON_LINK | MTK_PHY_LED_ON_FDX | MTK_PHY_LED_ON_HDX | ++ MTK_PHY_LED_ON_LINKDOWN)) || ++ (blink & (MTK_PHY_LED_BLINK_RX | MTK_PHY_LED_BLINK_TX))) ++ set_bit(bit_netdev, &priv->led_state); ++ else ++ clear_bit(bit_netdev, &priv->led_state); ++ ++ if (on & MTK_PHY_LED_ON_FORCE_ON) ++ set_bit(bit_on, &priv->led_state); ++ else ++ clear_bit(bit_on, &priv->led_state); ++ ++ if (blink & MTK_PHY_LED_BLINK_FORCE_BLINK) ++ set_bit(bit_blink, &priv->led_state); ++ else ++ clear_bit(bit_blink, &priv->led_state); ++ ++ if (!rules) ++ return 0; ++ ++ if (on & MTK_PHY_LED_ON_LINK) ++ *rules |= BIT(TRIGGER_NETDEV_LINK); ++ ++ if (on & MTK_PHY_LED_ON_LINK10) ++ *rules |= BIT(TRIGGER_NETDEV_LINK_10); ++ ++ if (on & MTK_PHY_LED_ON_LINK100) ++ *rules |= BIT(TRIGGER_NETDEV_LINK_100); ++ ++ if (on & MTK_PHY_LED_ON_LINK1000) ++ *rules |= BIT(TRIGGER_NETDEV_LINK_1000); ++ ++ if (on & MTK_PHY_LED_ON_FDX) ++ *rules |= BIT(TRIGGER_NETDEV_FULL_DUPLEX); ++ ++ if (on & MTK_PHY_LED_ON_HDX) ++ *rules |= BIT(TRIGGER_NETDEV_HALF_DUPLEX); ++ ++ if (blink & MTK_PHY_LED_BLINK_RX) ++ *rules |= BIT(TRIGGER_NETDEV_RX); ++ ++ if (blink & MTK_PHY_LED_BLINK_TX) ++ *rules |= BIT(TRIGGER_NETDEV_TX); ++ ++ return 0; ++}; ++ ++static int mt798x_phy_led_hw_control_set(struct phy_device *phydev, u8 index, ++ unsigned long rules) ++{ ++ unsigned int bit_netdev = MTK_PHY_LED_STATE_NETDEV + (index ? 16 : 0); ++ struct mtk_socphy_priv *priv = phydev->priv; ++ u16 on = 0, blink = 0; ++ int ret; ++ ++ if (index > 1) ++ return -EINVAL; ++ ++ if (rules & BIT(TRIGGER_NETDEV_FULL_DUPLEX)) ++ on |= MTK_PHY_LED_ON_FDX; ++ ++ if (rules & BIT(TRIGGER_NETDEV_HALF_DUPLEX)) ++ on |= MTK_PHY_LED_ON_HDX; ++ ++ if (rules & (BIT(TRIGGER_NETDEV_LINK_10) | BIT(TRIGGER_NETDEV_LINK))) ++ on |= MTK_PHY_LED_ON_LINK10; ++ ++ if (rules & (BIT(TRIGGER_NETDEV_LINK_100) | BIT(TRIGGER_NETDEV_LINK))) ++ on |= MTK_PHY_LED_ON_LINK100; ++ ++ if (rules & (BIT(TRIGGER_NETDEV_LINK_1000) | BIT(TRIGGER_NETDEV_LINK))) ++ on |= MTK_PHY_LED_ON_LINK1000; ++ ++ if (rules & BIT(TRIGGER_NETDEV_RX)) { ++ blink |= (on & MTK_PHY_LED_ON_LINK) ? ++ (((on & MTK_PHY_LED_ON_LINK10) ? MTK_PHY_LED_BLINK_10RX : 0) | ++ ((on & MTK_PHY_LED_ON_LINK100) ? MTK_PHY_LED_BLINK_100RX : 0) | ++ ((on & MTK_PHY_LED_ON_LINK1000) ? MTK_PHY_LED_BLINK_1000RX : 0)) : ++ MTK_PHY_LED_BLINK_RX; ++ } ++ ++ if (rules & BIT(TRIGGER_NETDEV_TX)) { ++ blink |= (on & MTK_PHY_LED_ON_LINK) ? ++ (((on & MTK_PHY_LED_ON_LINK10) ? MTK_PHY_LED_BLINK_10TX : 0) | ++ ((on & MTK_PHY_LED_ON_LINK100) ? MTK_PHY_LED_BLINK_100TX : 0) | ++ ((on & MTK_PHY_LED_ON_LINK1000) ? MTK_PHY_LED_BLINK_1000TX : 0)) : ++ MTK_PHY_LED_BLINK_TX; ++ } ++ ++ if (blink || on) ++ set_bit(bit_netdev, &priv->led_state); ++ else ++ clear_bit(bit_netdev, &priv->led_state); ++ ++ ret = phy_modify_mmd(phydev, MDIO_MMD_VEND2, index ? ++ MTK_PHY_LED1_ON_CTRL : ++ MTK_PHY_LED0_ON_CTRL, ++ MTK_PHY_LED_ON_FDX | ++ MTK_PHY_LED_ON_HDX | ++ MTK_PHY_LED_ON_LINK, ++ on); ++ ++ if (ret) ++ return ret; ++ ++ return phy_write_mmd(phydev, MDIO_MMD_VEND2, index ? ++ MTK_PHY_LED1_BLINK_CTRL : ++ MTK_PHY_LED0_BLINK_CTRL, blink); ++}; ++ ++static bool mt7988_phy_led_get_polarity(struct phy_device *phydev, int led_num) ++{ ++ struct mtk_socphy_shared *priv = phydev->shared->priv; ++ u32 polarities; ++ ++ if (led_num == 0) ++ polarities = ~(priv->boottrap); ++ else ++ polarities = MTK_PHY_LED1_DEFAULT_POLARITIES; ++ ++ if (polarities & BIT(phydev->mdio.addr)) ++ return true; ++ ++ return false; ++} ++ ++static int mt7988_phy_fix_leds_polarities(struct phy_device *phydev) ++{ ++ struct pinctrl *pinctrl; ++ int index; ++ ++ /* Setup LED polarity according to bootstrap use of LED pins */ ++ for (index = 0; index < 2; ++index) ++ phy_modify_mmd(phydev, MDIO_MMD_VEND2, index ? ++ MTK_PHY_LED1_ON_CTRL : MTK_PHY_LED0_ON_CTRL, ++ MTK_PHY_LED_ON_POLARITY, ++ mt7988_phy_led_get_polarity(phydev, index) ? ++ MTK_PHY_LED_ON_POLARITY : 0); ++ ++ /* Only now setup pinctrl to avoid bogus blinking */ ++ pinctrl = devm_pinctrl_get_select(&phydev->mdio.dev, "gbe-led"); ++ if (IS_ERR(pinctrl)) ++ dev_err(&phydev->mdio.bus->dev, "Failed to setup PHY LED pinctrl\n"); ++ ++ return 0; ++} ++ ++static int mt7988_phy_probe_shared(struct phy_device *phydev) ++{ ++ struct device_node *np = dev_of_node(&phydev->mdio.bus->dev); ++ struct mtk_socphy_shared *shared = phydev->shared->priv; ++ struct regmap *regmap; ++ u32 reg; ++ int ret; ++ ++ /* The LED0 of the 4 PHYs in MT7988 are wired to SoC pins LED_A, LED_B, ++ * LED_C and LED_D respectively. At the same time those pins are used to ++ * bootstrap configuration of the reference clock source (LED_A), ++ * DRAM DDRx16b x2/x1 (LED_B) and boot device (LED_C, LED_D). ++ * In practise this is done using a LED and a resistor pulling the pin ++ * either to GND or to VIO. ++ * The detected value at boot time is accessible at run-time using the ++ * TPBANK0 register located in the gpio base of the pinctrl, in order ++ * to read it here it needs to be referenced by a phandle called ++ * 'mediatek,pio' in the MDIO bus hosting the PHY. ++ * The 4 bits in TPBANK0 are kept as package shared data and are used to ++ * set LED polarity for each of the LED0. ++ */ ++ regmap = syscon_regmap_lookup_by_phandle(np, "mediatek,pio"); ++ if (IS_ERR(regmap)) ++ return PTR_ERR(regmap); ++ ++ ret = regmap_read(regmap, RG_GPIO_MISC_TPBANK0, ®); ++ if (ret) ++ return ret; ++ ++ shared->boottrap = FIELD_GET(RG_GPIO_MISC_TPBANK0_BOOTMODE, reg); ++ ++ return 0; ++} ++ ++static void mt798x_phy_leds_state_init(struct phy_device *phydev) ++{ ++ int i; ++ ++ for (i = 0; i < 2; ++i) ++ mt798x_phy_led_hw_control_get(phydev, i, NULL); ++} ++ ++static int mt7988_phy_probe(struct phy_device *phydev) ++{ ++ struct mtk_socphy_shared *shared; ++ struct mtk_socphy_priv *priv; ++ int err; ++ ++ if (phydev->mdio.addr > 3) ++ return -EINVAL; ++ ++ err = devm_phy_package_join(&phydev->mdio.dev, phydev, 0, ++ sizeof(struct mtk_socphy_shared)); ++ if (err) ++ return err; ++ ++ if (phy_package_probe_once(phydev)) { ++ err = mt7988_phy_probe_shared(phydev); ++ if (err) ++ return err; ++ } ++ ++ shared = phydev->shared->priv; ++ priv = &shared->priv[phydev->mdio.addr]; ++ ++ phydev->priv = priv; ++ ++ mt798x_phy_leds_state_init(phydev); ++ ++ err = mt7988_phy_fix_leds_polarities(phydev); ++ if (err) ++ return err; ++ ++ /* Disable TX power saving at probing to: ++ * 1. Meet common mode compliance test criteria ++ * 2. Make sure that TX-VCM calibration works fine ++ */ ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RXADC_CTRL_RG7, ++ MTK_PHY_DA_AD_BUF_BIAS_LP_MASK, 0x3 << 8); ++ ++ return mt798x_phy_calibration(phydev); ++} ++ ++static int mt7981_phy_probe(struct phy_device *phydev) ++{ ++ struct mtk_socphy_priv *priv; ++ ++ priv = devm_kzalloc(&phydev->mdio.dev, sizeof(struct mtk_socphy_priv), ++ GFP_KERNEL); ++ if (!priv) ++ return -ENOMEM; ++ ++ phydev->priv = priv; ++ ++ mt798x_phy_leds_state_init(phydev); ++ ++ return mt798x_phy_calibration(phydev); ++} ++ ++static struct phy_driver mtk_socphy_driver[] = { ++ { ++ PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7981), ++ .name = "MediaTek MT7981 PHY", ++ .config_init = mt798x_phy_config_init, ++ .config_intr = genphy_no_config_intr, ++ .handle_interrupt = genphy_handle_interrupt_no_ack, ++ .probe = mt7981_phy_probe, ++ .suspend = genphy_suspend, ++ .resume = genphy_resume, ++ .read_page = mtk_socphy_read_page, ++ .write_page = mtk_socphy_write_page, ++ .led_blink_set = mt798x_phy_led_blink_set, ++ .led_brightness_set = mt798x_phy_led_brightness_set, ++ .led_hw_is_supported = mt798x_phy_led_hw_is_supported, ++ .led_hw_control_set = mt798x_phy_led_hw_control_set, ++ .led_hw_control_get = mt798x_phy_led_hw_control_get, ++ }, ++ { ++ PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7988), ++ .name = "MediaTek MT7988 PHY", ++ .config_init = mt798x_phy_config_init, ++ .config_intr = genphy_no_config_intr, ++ .handle_interrupt = genphy_handle_interrupt_no_ack, ++ .probe = mt7988_phy_probe, ++ .suspend = genphy_suspend, ++ .resume = genphy_resume, ++ .read_page = mtk_socphy_read_page, ++ .write_page = mtk_socphy_write_page, ++ .led_blink_set = mt798x_phy_led_blink_set, ++ .led_brightness_set = mt798x_phy_led_brightness_set, ++ .led_hw_is_supported = mt798x_phy_led_hw_is_supported, ++ .led_hw_control_set = mt798x_phy_led_hw_control_set, ++ .led_hw_control_get = mt798x_phy_led_hw_control_get, ++ }, ++}; ++ ++module_phy_driver(mtk_socphy_driver); ++ ++static struct mdio_device_id __maybe_unused mtk_socphy_tbl[] = { ++ { PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7981) }, ++ { PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7988) }, ++ { } ++}; ++ ++MODULE_DESCRIPTION("MediaTek SoC Gigabit Ethernet PHY driver"); ++MODULE_AUTHOR("Daniel Golle "); ++MODULE_AUTHOR("SkyLake Huang "); ++MODULE_LICENSE("GPL"); ++ ++MODULE_DEVICE_TABLE(mdio, mtk_socphy_tbl); +--- /dev/null ++++ b/drivers/net/phy/mediatek/mtk-ge.c +@@ -0,0 +1,148 @@ ++// SPDX-License-Identifier: GPL-2.0+ ++#include ++#include ++#include ++#include ++ ++#define MTK_EXT_PAGE_ACCESS 0x1f ++#define MTK_PHY_PAGE_STANDARD 0x0000 ++#define MTK_PHY_PAGE_EXTENDED 0x0001 ++#define MTK_PHY_PAGE_EXTENDED_2 0x0002 ++#define MTK_PHY_PAGE_EXTENDED_3 0x0003 ++#define MTK_PHY_PAGE_EXTENDED_2A30 0x2a30 ++#define MTK_PHY_PAGE_EXTENDED_52B5 0x52b5 ++ ++static int mtk_gephy_read_page(struct phy_device *phydev) ++{ ++ return __phy_read(phydev, MTK_EXT_PAGE_ACCESS); ++} ++ ++static int mtk_gephy_write_page(struct phy_device *phydev, int page) ++{ ++ return __phy_write(phydev, MTK_EXT_PAGE_ACCESS, page); ++} ++ ++static void mtk_gephy_config_init(struct phy_device *phydev) ++{ ++ /* Disable EEE */ ++ phy_write_mmd(phydev, MDIO_MMD_AN, MDIO_AN_EEE_ADV, 0); ++ ++ /* Enable HW auto downshift */ ++ phy_modify_paged(phydev, MTK_PHY_PAGE_EXTENDED, 0x14, 0, BIT(4)); ++ ++ /* Increase SlvDPSready time */ ++ phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); ++ __phy_write(phydev, 0x10, 0xafae); ++ __phy_write(phydev, 0x12, 0x2f); ++ __phy_write(phydev, 0x10, 0x8fae); ++ phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); ++ ++ /* Adjust 100_mse_threshold */ ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x123, 0xffff); ++ ++ /* Disable mcc */ ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, 0xa6, 0x300); ++} ++ ++static int mt7530_phy_config_init(struct phy_device *phydev) ++{ ++ mtk_gephy_config_init(phydev); ++ ++ /* Increase post_update_timer */ ++ phy_write_paged(phydev, MTK_PHY_PAGE_EXTENDED_3, 0x11, 0x4b); ++ ++ return 0; ++} ++ ++static int mt7530_led_config_of(struct phy_device *phydev) ++{ ++ struct device_node *np = phydev->mdio.dev.of_node; ++ const __be32 *paddr; ++ int len; ++ int i; ++ ++ paddr = of_get_property(np, "mediatek,led-config", &len); ++ if (!paddr) ++ return 0; ++ ++ if (len < (2 * sizeof(*paddr))) ++ return -EINVAL; ++ ++ len /= sizeof(*paddr); ++ ++ phydev_warn(phydev, "Configure LED registers (num=%d)\n", len); ++ for (i = 0; i < len - 1; i += 2) { ++ u32 reg; ++ u32 val; ++ ++ reg = be32_to_cpup(paddr + i); ++ val = be32_to_cpup(paddr + i + 1); ++ ++ phy_write_mmd(phydev, MDIO_MMD_VEND2, reg, val); ++ } ++ ++ return 0; ++} ++ ++static int mt7531_phy_config_init(struct phy_device *phydev) ++{ ++ mtk_gephy_config_init(phydev); ++ ++ /* PHY link down power saving enable */ ++ phy_set_bits(phydev, 0x17, BIT(4)); ++ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, 0xc6, 0x300); ++ ++ /* Set TX Pair delay selection */ ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x13, 0x404); ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x14, 0x404); ++ ++ /* LED Config*/ ++ mt7530_led_config_of(phydev); ++ ++ return 0; ++} ++ ++static struct phy_driver mtk_gephy_driver[] = { ++ { ++ PHY_ID_MATCH_EXACT(0x03a29412), ++ .name = "MediaTek MT7530 PHY", ++ .config_init = mt7530_phy_config_init, ++ /* Interrupts are handled by the switch, not the PHY ++ * itself. ++ */ ++ .config_intr = genphy_no_config_intr, ++ .handle_interrupt = genphy_handle_interrupt_no_ack, ++ .suspend = genphy_suspend, ++ .resume = genphy_resume, ++ .read_page = mtk_gephy_read_page, ++ .write_page = mtk_gephy_write_page, ++ }, ++ { ++ PHY_ID_MATCH_EXACT(0x03a29441), ++ .name = "MediaTek MT7531 PHY", ++ .config_init = mt7531_phy_config_init, ++ /* Interrupts are handled by the switch, not the PHY ++ * itself. ++ */ ++ .config_intr = genphy_no_config_intr, ++ .handle_interrupt = genphy_handle_interrupt_no_ack, ++ .suspend = genphy_suspend, ++ .resume = genphy_resume, ++ .read_page = mtk_gephy_read_page, ++ .write_page = mtk_gephy_write_page, ++ }, ++}; ++ ++module_phy_driver(mtk_gephy_driver); ++ ++static struct mdio_device_id __maybe_unused mtk_gephy_tbl[] = { ++ { PHY_ID_MATCH_EXACT(0x03a29441) }, ++ { PHY_ID_MATCH_EXACT(0x03a29412) }, ++ { } ++}; ++ ++MODULE_DESCRIPTION("MediaTek Gigabit Ethernet PHY driver"); ++MODULE_AUTHOR("DENG, Qingfang "); ++MODULE_LICENSE("GPL"); ++ ++MODULE_DEVICE_TABLE(mdio, mtk_gephy_tbl); diff --git a/target/linux/mediatek/patches-6.6/733-02-net-phy-mediatek-Fix-spelling-errors-and-rearrange-v.patch b/target/linux/mediatek/patches-6.6/733-02-net-phy-mediatek-Fix-spelling-errors-and-rearrange-v.patch new file mode 100644 index 0000000000..901949fe9f --- /dev/null +++ b/target/linux/mediatek/patches-6.6/733-02-net-phy-mediatek-Fix-spelling-errors-and-rearrange-v.patch @@ -0,0 +1,62 @@ +From 12054d38fc55adbfa2b40299ad8af3449d882ee2 Mon Sep 17 00:00:00 2001 +From: "SkyLake.Huang" +Date: Mon, 1 Jul 2024 18:54:06 +0800 +Subject: [PATCH 02/13] net: phy: mediatek: Fix spelling errors and rearrange + variables + +This patch fixes spelling errors which comes from mediatek-ge-soc.c and +rearrange variables with reverse Xmas tree order. + +Signed-off-by: SkyLake.Huang +--- + drivers/net/phy/mediatek/mtk-ge-soc.c | 19 ++++++++++--------- + 1 file changed, 10 insertions(+), 9 deletions(-) + +--- a/drivers/net/phy/mediatek/mtk-ge-soc.c ++++ b/drivers/net/phy/mediatek/mtk-ge-soc.c +@@ -408,16 +408,17 @@ static int tx_offset_cal_efuse(struct ph + + static int tx_amp_fill_result(struct phy_device *phydev, u16 *buf) + { +- int i; +- int bias[16] = {}; +- const int vals_9461[16] = { 7, 1, 4, 7, +- 7, 1, 4, 7, +- 7, 1, 4, 7, +- 7, 1, 4, 7 }; + const int vals_9481[16] = { 10, 6, 6, 10, + 10, 6, 6, 10, + 10, 6, 6, 10, + 10, 6, 6, 10 }; ++ const int vals_9461[16] = { 7, 1, 4, 7, ++ 7, 1, 4, 7, ++ 7, 1, 4, 7, ++ 7, 1, 4, 7 }; ++ int bias[16] = {}; ++ int i; ++ + switch (phydev->drv->phy_id) { + case MTK_GPHY_ID_MT7981: + /* We add some calibration to efuse values +@@ -1069,10 +1070,10 @@ static int start_cal(struct phy_device * + + static int mt798x_phy_calibration(struct phy_device *phydev) + { ++ struct nvmem_cell *cell; + int ret = 0; +- u32 *buf; + size_t len; +- struct nvmem_cell *cell; ++ u32 *buf; + + cell = nvmem_cell_get(&phydev->mdio.dev, "phy-cal-data"); + if (IS_ERR(cell)) { +@@ -1415,7 +1416,7 @@ static int mt7988_phy_probe_shared(struc + * LED_C and LED_D respectively. At the same time those pins are used to + * bootstrap configuration of the reference clock source (LED_A), + * DRAM DDRx16b x2/x1 (LED_B) and boot device (LED_C, LED_D). +- * In practise this is done using a LED and a resistor pulling the pin ++ * In practice this is done using a LED and a resistor pulling the pin + * either to GND or to VIO. + * The detected value at boot time is accessible at run-time using the + * TPBANK0 register located in the gpio base of the pinctrl, in order diff --git a/target/linux/mediatek/patches-6.6/733-03-net-phy-mediatek-Move-LED-helper-functions-into-mtk-.patch b/target/linux/mediatek/patches-6.6/733-03-net-phy-mediatek-Move-LED-helper-functions-into-mtk-.patch new file mode 100644 index 0000000000..9e6ae4b136 --- /dev/null +++ b/target/linux/mediatek/patches-6.6/733-03-net-phy-mediatek-Move-LED-helper-functions-into-mtk-.patch @@ -0,0 +1,742 @@ +From 434e41555c45ec10b19320024163bb009da168bc Mon Sep 17 00:00:00 2001 +From: "SkyLake.Huang" +Date: Mon, 1 Jul 2024 18:54:07 +0800 +Subject: [PATCH 03/13] net: phy: mediatek: Move LED helper functions into mtk + phy lib + +This patch creates mtk-phy-lib.c & mtk-phy.h and integrates mtk-ge-soc.c's +LED helper functions so that we can use those helper functions in other +MTK's ethernet phy driver. + +Signed-off-by: SkyLake.Huang +--- + drivers/net/phy/mediatek/Kconfig | 5 + + drivers/net/phy/mediatek/Makefile | 1 + + drivers/net/phy/mediatek/mtk-ge-soc.c | 262 +++---------------------- + drivers/net/phy/mediatek/mtk-phy-lib.c | 251 +++++++++++++++++++++++ + drivers/net/phy/mediatek/mtk.h | 82 ++++++++ + 6 files changed, 368 insertions(+), 235 deletions(-) + create mode 100644 drivers/net/phy/mediatek/mtk-phy-lib.c + create mode 100644 drivers/net/phy/mediatek/mtk.h + +--- a/drivers/net/phy/mediatek/Kconfig ++++ b/drivers/net/phy/mediatek/Kconfig +@@ -1,6 +1,10 @@ + # SPDX-License-Identifier: GPL-2.0-only ++config MTK_NET_PHYLIB ++ tristate ++ + config MEDIATEK_GE_PHY + tristate "MediaTek Gigabit Ethernet PHYs" ++ select MTK_NET_PHYLIB + help + Supports the MediaTek non-built-in Gigabit Ethernet PHYs. + +@@ -13,6 +17,7 @@ config MEDIATEK_GE_SOC_PHY + tristate "MediaTek SoC Ethernet PHYs" + depends on (ARM64 && ARCH_MEDIATEK) || COMPILE_TEST + select NVMEM_MTK_EFUSE ++ select MTK_NET_PHYLIB + help + Supports MediaTek SoC built-in Gigabit Ethernet PHYs. + +--- a/drivers/net/phy/mediatek/Makefile ++++ b/drivers/net/phy/mediatek/Makefile +@@ -1,3 +1,4 @@ + # SPDX-License-Identifier: GPL-2.0 ++obj-$(CONFIG_MTK_NET_PHYLIB) += mtk-phy-lib.o + obj-$(CONFIG_MEDIATEK_GE_PHY) += mtk-ge.o + obj-$(CONFIG_MEDIATEK_GE_SOC_PHY) += mtk-ge-soc.o +--- a/drivers/net/phy/mediatek/mtk-ge-soc.c ++++ b/drivers/net/phy/mediatek/mtk-ge-soc.c +@@ -8,6 +8,8 @@ + #include + #include + ++#include "mtk.h" ++ + #define MTK_GPHY_ID_MT7981 0x03a29461 + #define MTK_GPHY_ID_MT7988 0x03a29481 + +@@ -210,41 +212,6 @@ + #define MTK_PHY_DA_TX_R50_PAIR_D 0x540 + + /* Registers on MDIO_MMD_VEND2 */ +-#define MTK_PHY_LED0_ON_CTRL 0x24 +-#define MTK_PHY_LED1_ON_CTRL 0x26 +-#define MTK_PHY_LED_ON_MASK GENMASK(6, 0) +-#define MTK_PHY_LED_ON_LINK1000 BIT(0) +-#define MTK_PHY_LED_ON_LINK100 BIT(1) +-#define MTK_PHY_LED_ON_LINK10 BIT(2) +-#define MTK_PHY_LED_ON_LINK (MTK_PHY_LED_ON_LINK10 |\ +- MTK_PHY_LED_ON_LINK100 |\ +- MTK_PHY_LED_ON_LINK1000) +-#define MTK_PHY_LED_ON_LINKDOWN BIT(3) +-#define MTK_PHY_LED_ON_FDX BIT(4) /* Full duplex */ +-#define MTK_PHY_LED_ON_HDX BIT(5) /* Half duplex */ +-#define MTK_PHY_LED_ON_FORCE_ON BIT(6) +-#define MTK_PHY_LED_ON_POLARITY BIT(14) +-#define MTK_PHY_LED_ON_ENABLE BIT(15) +- +-#define MTK_PHY_LED0_BLINK_CTRL 0x25 +-#define MTK_PHY_LED1_BLINK_CTRL 0x27 +-#define MTK_PHY_LED_BLINK_1000TX BIT(0) +-#define MTK_PHY_LED_BLINK_1000RX BIT(1) +-#define MTK_PHY_LED_BLINK_100TX BIT(2) +-#define MTK_PHY_LED_BLINK_100RX BIT(3) +-#define MTK_PHY_LED_BLINK_10TX BIT(4) +-#define MTK_PHY_LED_BLINK_10RX BIT(5) +-#define MTK_PHY_LED_BLINK_RX (MTK_PHY_LED_BLINK_10RX |\ +- MTK_PHY_LED_BLINK_100RX |\ +- MTK_PHY_LED_BLINK_1000RX) +-#define MTK_PHY_LED_BLINK_TX (MTK_PHY_LED_BLINK_10TX |\ +- MTK_PHY_LED_BLINK_100TX |\ +- MTK_PHY_LED_BLINK_1000TX) +-#define MTK_PHY_LED_BLINK_COLLISION BIT(6) +-#define MTK_PHY_LED_BLINK_RX_CRC_ERR BIT(7) +-#define MTK_PHY_LED_BLINK_RX_IDLE_ERR BIT(8) +-#define MTK_PHY_LED_BLINK_FORCE_BLINK BIT(9) +- + #define MTK_PHY_LED1_DEFAULT_POLARITIES BIT(1) + + #define MTK_PHY_RG_BG_RASEL 0x115 +@@ -299,10 +266,6 @@ enum CAL_MODE { + SW_M + }; + +-#define MTK_PHY_LED_STATE_FORCE_ON 0 +-#define MTK_PHY_LED_STATE_FORCE_BLINK 1 +-#define MTK_PHY_LED_STATE_NETDEV 2 +- + struct mtk_socphy_priv { + unsigned long led_state; + }; +@@ -1131,84 +1094,39 @@ static int mt798x_phy_config_init(struct + return mt798x_phy_calibration(phydev); + } + +-static int mt798x_phy_hw_led_on_set(struct phy_device *phydev, u8 index, +- bool on) +-{ +- unsigned int bit_on = MTK_PHY_LED_STATE_FORCE_ON + (index ? 16 : 0); +- struct mtk_socphy_priv *priv = phydev->priv; +- bool changed; +- +- if (on) +- changed = !test_and_set_bit(bit_on, &priv->led_state); +- else +- changed = !!test_and_clear_bit(bit_on, &priv->led_state); +- +- changed |= !!test_and_clear_bit(MTK_PHY_LED_STATE_NETDEV + +- (index ? 16 : 0), &priv->led_state); +- if (changed) +- return phy_modify_mmd(phydev, MDIO_MMD_VEND2, index ? +- MTK_PHY_LED1_ON_CTRL : MTK_PHY_LED0_ON_CTRL, +- MTK_PHY_LED_ON_MASK, +- on ? MTK_PHY_LED_ON_FORCE_ON : 0); +- else +- return 0; +-} +- +-static int mt798x_phy_hw_led_blink_set(struct phy_device *phydev, u8 index, +- bool blinking) +-{ +- unsigned int bit_blink = MTK_PHY_LED_STATE_FORCE_BLINK + (index ? 16 : 0); +- struct mtk_socphy_priv *priv = phydev->priv; +- bool changed; +- +- if (blinking) +- changed = !test_and_set_bit(bit_blink, &priv->led_state); +- else +- changed = !!test_and_clear_bit(bit_blink, &priv->led_state); +- +- changed |= !!test_bit(MTK_PHY_LED_STATE_NETDEV + +- (index ? 16 : 0), &priv->led_state); +- if (changed) +- return phy_write_mmd(phydev, MDIO_MMD_VEND2, index ? +- MTK_PHY_LED1_BLINK_CTRL : MTK_PHY_LED0_BLINK_CTRL, +- blinking ? MTK_PHY_LED_BLINK_FORCE_BLINK : 0); +- else +- return 0; +-} +- + static int mt798x_phy_led_blink_set(struct phy_device *phydev, u8 index, + unsigned long *delay_on, + unsigned long *delay_off) + { ++ struct mtk_socphy_priv *priv = phydev->priv; + bool blinking = false; + int err = 0; + +- if (index > 1) +- return -EINVAL; +- +- if (delay_on && delay_off && (*delay_on > 0) && (*delay_off > 0)) { +- blinking = true; +- *delay_on = 50; +- *delay_off = 50; +- } ++ err = mtk_phy_led_num_dly_cfg(index, delay_on, delay_off, &blinking); ++ if (err < 0) ++ return err; + +- err = mt798x_phy_hw_led_blink_set(phydev, index, blinking); ++ err = mtk_phy_hw_led_blink_set(phydev, index, &priv->led_state, ++ blinking); + if (err) + return err; + +- return mt798x_phy_hw_led_on_set(phydev, index, false); ++ return mtk_phy_hw_led_on_set(phydev, index, &priv->led_state, ++ MTK_GPHY_LED_ON_MASK, false); + } + + static int mt798x_phy_led_brightness_set(struct phy_device *phydev, + u8 index, enum led_brightness value) + { ++ struct mtk_socphy_priv *priv = phydev->priv; + int err; + +- err = mt798x_phy_hw_led_blink_set(phydev, index, false); ++ err = mtk_phy_hw_led_blink_set(phydev, index, &priv->led_state, false); + if (err) + return err; + +- return mt798x_phy_hw_led_on_set(phydev, index, (value != LED_OFF)); ++ return mtk_phy_hw_led_on_set(phydev, index, &priv->led_state, ++ MTK_GPHY_LED_ON_MASK, (value != LED_OFF)); + } + + static const unsigned long supported_triggers = (BIT(TRIGGER_NETDEV_FULL_DUPLEX) | +@@ -1223,148 +1141,30 @@ static const unsigned long supported_tri + static int mt798x_phy_led_hw_is_supported(struct phy_device *phydev, u8 index, + unsigned long rules) + { +- if (index > 1) +- return -EINVAL; +- +- /* All combinations of the supported triggers are allowed */ +- if (rules & ~supported_triggers) +- return -EOPNOTSUPP; +- +- return 0; +-}; ++ return mtk_phy_led_hw_is_supported(phydev, index, rules, ++ supported_triggers); ++} + + static int mt798x_phy_led_hw_control_get(struct phy_device *phydev, u8 index, + unsigned long *rules) + { +- unsigned int bit_blink = MTK_PHY_LED_STATE_FORCE_BLINK + (index ? 16 : 0); +- unsigned int bit_netdev = MTK_PHY_LED_STATE_NETDEV + (index ? 16 : 0); +- unsigned int bit_on = MTK_PHY_LED_STATE_FORCE_ON + (index ? 16 : 0); + struct mtk_socphy_priv *priv = phydev->priv; +- int on, blink; +- +- if (index > 1) +- return -EINVAL; +- +- on = phy_read_mmd(phydev, MDIO_MMD_VEND2, +- index ? MTK_PHY_LED1_ON_CTRL : MTK_PHY_LED0_ON_CTRL); +- +- if (on < 0) +- return -EIO; +- +- blink = phy_read_mmd(phydev, MDIO_MMD_VEND2, +- index ? MTK_PHY_LED1_BLINK_CTRL : +- MTK_PHY_LED0_BLINK_CTRL); +- if (blink < 0) +- return -EIO; +- +- if ((on & (MTK_PHY_LED_ON_LINK | MTK_PHY_LED_ON_FDX | MTK_PHY_LED_ON_HDX | +- MTK_PHY_LED_ON_LINKDOWN)) || +- (blink & (MTK_PHY_LED_BLINK_RX | MTK_PHY_LED_BLINK_TX))) +- set_bit(bit_netdev, &priv->led_state); +- else +- clear_bit(bit_netdev, &priv->led_state); +- +- if (on & MTK_PHY_LED_ON_FORCE_ON) +- set_bit(bit_on, &priv->led_state); +- else +- clear_bit(bit_on, &priv->led_state); +- +- if (blink & MTK_PHY_LED_BLINK_FORCE_BLINK) +- set_bit(bit_blink, &priv->led_state); +- else +- clear_bit(bit_blink, &priv->led_state); +- +- if (!rules) +- return 0; +- +- if (on & MTK_PHY_LED_ON_LINK) +- *rules |= BIT(TRIGGER_NETDEV_LINK); + +- if (on & MTK_PHY_LED_ON_LINK10) +- *rules |= BIT(TRIGGER_NETDEV_LINK_10); +- +- if (on & MTK_PHY_LED_ON_LINK100) +- *rules |= BIT(TRIGGER_NETDEV_LINK_100); +- +- if (on & MTK_PHY_LED_ON_LINK1000) +- *rules |= BIT(TRIGGER_NETDEV_LINK_1000); +- +- if (on & MTK_PHY_LED_ON_FDX) +- *rules |= BIT(TRIGGER_NETDEV_FULL_DUPLEX); +- +- if (on & MTK_PHY_LED_ON_HDX) +- *rules |= BIT(TRIGGER_NETDEV_HALF_DUPLEX); +- +- if (blink & MTK_PHY_LED_BLINK_RX) +- *rules |= BIT(TRIGGER_NETDEV_RX); +- +- if (blink & MTK_PHY_LED_BLINK_TX) +- *rules |= BIT(TRIGGER_NETDEV_TX); +- +- return 0; ++ return mtk_phy_led_hw_ctrl_get(phydev, index, rules, &priv->led_state, ++ MTK_GPHY_LED_ON_SET, ++ MTK_GPHY_LED_RX_BLINK_SET, ++ MTK_GPHY_LED_TX_BLINK_SET); + }; + + static int mt798x_phy_led_hw_control_set(struct phy_device *phydev, u8 index, + unsigned long rules) + { +- unsigned int bit_netdev = MTK_PHY_LED_STATE_NETDEV + (index ? 16 : 0); + struct mtk_socphy_priv *priv = phydev->priv; +- u16 on = 0, blink = 0; +- int ret; + +- if (index > 1) +- return -EINVAL; +- +- if (rules & BIT(TRIGGER_NETDEV_FULL_DUPLEX)) +- on |= MTK_PHY_LED_ON_FDX; +- +- if (rules & BIT(TRIGGER_NETDEV_HALF_DUPLEX)) +- on |= MTK_PHY_LED_ON_HDX; +- +- if (rules & (BIT(TRIGGER_NETDEV_LINK_10) | BIT(TRIGGER_NETDEV_LINK))) +- on |= MTK_PHY_LED_ON_LINK10; +- +- if (rules & (BIT(TRIGGER_NETDEV_LINK_100) | BIT(TRIGGER_NETDEV_LINK))) +- on |= MTK_PHY_LED_ON_LINK100; +- +- if (rules & (BIT(TRIGGER_NETDEV_LINK_1000) | BIT(TRIGGER_NETDEV_LINK))) +- on |= MTK_PHY_LED_ON_LINK1000; +- +- if (rules & BIT(TRIGGER_NETDEV_RX)) { +- blink |= (on & MTK_PHY_LED_ON_LINK) ? +- (((on & MTK_PHY_LED_ON_LINK10) ? MTK_PHY_LED_BLINK_10RX : 0) | +- ((on & MTK_PHY_LED_ON_LINK100) ? MTK_PHY_LED_BLINK_100RX : 0) | +- ((on & MTK_PHY_LED_ON_LINK1000) ? MTK_PHY_LED_BLINK_1000RX : 0)) : +- MTK_PHY_LED_BLINK_RX; +- } +- +- if (rules & BIT(TRIGGER_NETDEV_TX)) { +- blink |= (on & MTK_PHY_LED_ON_LINK) ? +- (((on & MTK_PHY_LED_ON_LINK10) ? MTK_PHY_LED_BLINK_10TX : 0) | +- ((on & MTK_PHY_LED_ON_LINK100) ? MTK_PHY_LED_BLINK_100TX : 0) | +- ((on & MTK_PHY_LED_ON_LINK1000) ? MTK_PHY_LED_BLINK_1000TX : 0)) : +- MTK_PHY_LED_BLINK_TX; +- } +- +- if (blink || on) +- set_bit(bit_netdev, &priv->led_state); +- else +- clear_bit(bit_netdev, &priv->led_state); +- +- ret = phy_modify_mmd(phydev, MDIO_MMD_VEND2, index ? +- MTK_PHY_LED1_ON_CTRL : +- MTK_PHY_LED0_ON_CTRL, +- MTK_PHY_LED_ON_FDX | +- MTK_PHY_LED_ON_HDX | +- MTK_PHY_LED_ON_LINK, +- on); +- +- if (ret) +- return ret; +- +- return phy_write_mmd(phydev, MDIO_MMD_VEND2, index ? +- MTK_PHY_LED1_BLINK_CTRL : +- MTK_PHY_LED0_BLINK_CTRL, blink); ++ return mtk_phy_led_hw_ctrl_set(phydev, index, rules, &priv->led_state, ++ MTK_GPHY_LED_ON_SET, ++ MTK_GPHY_LED_RX_BLINK_SET, ++ MTK_GPHY_LED_TX_BLINK_SET); + }; + + static bool mt7988_phy_led_get_polarity(struct phy_device *phydev, int led_num) +@@ -1438,14 +1238,6 @@ static int mt7988_phy_probe_shared(struc + return 0; + } + +-static void mt798x_phy_leds_state_init(struct phy_device *phydev) +-{ +- int i; +- +- for (i = 0; i < 2; ++i) +- mt798x_phy_led_hw_control_get(phydev, i, NULL); +-} +- + static int mt7988_phy_probe(struct phy_device *phydev) + { + struct mtk_socphy_shared *shared; +@@ -1471,7 +1263,7 @@ static int mt7988_phy_probe(struct phy_d + + phydev->priv = priv; + +- mt798x_phy_leds_state_init(phydev); ++ mtk_phy_leds_state_init(phydev); + + err = mt7988_phy_fix_leds_polarities(phydev); + if (err) +@@ -1498,7 +1290,7 @@ static int mt7981_phy_probe(struct phy_d + + phydev->priv = priv; + +- mt798x_phy_leds_state_init(phydev); ++ mtk_phy_leds_state_init(phydev); + + return mt798x_phy_calibration(phydev); + } +--- /dev/null ++++ b/drivers/net/phy/mediatek/mtk-phy-lib.c +@@ -0,0 +1,251 @@ ++// SPDX-License-Identifier: GPL-2.0 ++#include ++#include ++ ++#include ++ ++#include "mtk.h" ++ ++int mtk_phy_led_hw_is_supported(struct phy_device *phydev, u8 index, ++ unsigned long rules, ++ unsigned long supported_triggers) ++{ ++ if (index > 1) ++ return -EINVAL; ++ ++ /* All combinations of the supported triggers are allowed */ ++ if (rules & ~supported_triggers) ++ return -EOPNOTSUPP; ++ ++ return 0; ++} ++EXPORT_SYMBOL_GPL(mtk_phy_led_hw_is_supported); ++ ++int mtk_phy_led_hw_ctrl_get(struct phy_device *phydev, u8 index, ++ unsigned long *rules, unsigned long *led_state, ++ u16 on_set, u16 rx_blink_set, u16 tx_blink_set) ++{ ++ unsigned int bit_blink = MTK_PHY_LED_STATE_FORCE_BLINK + ++ (index ? 16 : 0); ++ unsigned int bit_netdev = MTK_PHY_LED_STATE_NETDEV + (index ? 16 : 0); ++ unsigned int bit_on = MTK_PHY_LED_STATE_FORCE_ON + (index ? 16 : 0); ++ int on, blink; ++ ++ if (index > 1) ++ return -EINVAL; ++ ++ on = phy_read_mmd(phydev, MDIO_MMD_VEND2, ++ index ? MTK_PHY_LED1_ON_CTRL : MTK_PHY_LED0_ON_CTRL); ++ ++ if (on < 0) ++ return -EIO; ++ ++ blink = phy_read_mmd(phydev, MDIO_MMD_VEND2, ++ index ? MTK_PHY_LED1_BLINK_CTRL : ++ MTK_PHY_LED0_BLINK_CTRL); ++ if (blink < 0) ++ return -EIO; ++ ++ if ((on & (on_set | MTK_PHY_LED_ON_FDX | ++ MTK_PHY_LED_ON_HDX | MTK_PHY_LED_ON_LINKDOWN)) || ++ (blink & (rx_blink_set | tx_blink_set))) ++ set_bit(bit_netdev, led_state); ++ else ++ clear_bit(bit_netdev, led_state); ++ ++ if (on & MTK_PHY_LED_ON_FORCE_ON) ++ set_bit(bit_on, led_state); ++ else ++ clear_bit(bit_on, led_state); ++ ++ if (blink & MTK_PHY_LED_BLINK_FORCE_BLINK) ++ set_bit(bit_blink, led_state); ++ else ++ clear_bit(bit_blink, led_state); ++ ++ if (!rules) ++ return 0; ++ ++ if (on & on_set) ++ *rules |= BIT(TRIGGER_NETDEV_LINK); ++ ++ if (on & MTK_PHY_LED_ON_LINK10) ++ *rules |= BIT(TRIGGER_NETDEV_LINK_10); ++ ++ if (on & MTK_PHY_LED_ON_LINK100) ++ *rules |= BIT(TRIGGER_NETDEV_LINK_100); ++ ++ if (on & MTK_PHY_LED_ON_LINK1000) ++ *rules |= BIT(TRIGGER_NETDEV_LINK_1000); ++ ++ if (on & MTK_PHY_LED_ON_LINK2500) ++ *rules |= BIT(TRIGGER_NETDEV_LINK_2500); ++ ++ if (on & MTK_PHY_LED_ON_FDX) ++ *rules |= BIT(TRIGGER_NETDEV_FULL_DUPLEX); ++ ++ if (on & MTK_PHY_LED_ON_HDX) ++ *rules |= BIT(TRIGGER_NETDEV_HALF_DUPLEX); ++ ++ if (blink & rx_blink_set) ++ *rules |= BIT(TRIGGER_NETDEV_RX); ++ ++ if (blink & tx_blink_set) ++ *rules |= BIT(TRIGGER_NETDEV_TX); ++ ++ return 0; ++} ++EXPORT_SYMBOL_GPL(mtk_phy_led_hw_ctrl_get); ++ ++int mtk_phy_led_hw_ctrl_set(struct phy_device *phydev, u8 index, ++ unsigned long rules, unsigned long *led_state, ++ u16 on_set, u16 rx_blink_set, u16 tx_blink_set) ++{ ++ unsigned int bit_netdev = MTK_PHY_LED_STATE_NETDEV + (index ? 16 : 0); ++ u16 on = 0, blink = 0; ++ int ret; ++ ++ if (index > 1) ++ return -EINVAL; ++ ++ if (rules & BIT(TRIGGER_NETDEV_FULL_DUPLEX)) ++ on |= MTK_PHY_LED_ON_FDX; ++ ++ if (rules & BIT(TRIGGER_NETDEV_HALF_DUPLEX)) ++ on |= MTK_PHY_LED_ON_HDX; ++ ++ if (rules & (BIT(TRIGGER_NETDEV_LINK_10) | BIT(TRIGGER_NETDEV_LINK))) ++ on |= MTK_PHY_LED_ON_LINK10; ++ ++ if (rules & (BIT(TRIGGER_NETDEV_LINK_100) | BIT(TRIGGER_NETDEV_LINK))) ++ on |= MTK_PHY_LED_ON_LINK100; ++ ++ if (rules & (BIT(TRIGGER_NETDEV_LINK_1000) | BIT(TRIGGER_NETDEV_LINK))) ++ on |= MTK_PHY_LED_ON_LINK1000; ++ ++ if (rules & (BIT(TRIGGER_NETDEV_LINK_2500) | BIT(TRIGGER_NETDEV_LINK))) ++ on |= MTK_PHY_LED_ON_LINK2500; ++ ++ if (rules & BIT(TRIGGER_NETDEV_RX)) { ++ blink |= (on & on_set) ? ++ (((on & MTK_PHY_LED_ON_LINK10) ? ++ MTK_PHY_LED_BLINK_10RX : 0) | ++ ((on & MTK_PHY_LED_ON_LINK100) ? ++ MTK_PHY_LED_BLINK_100RX : 0) | ++ ((on & MTK_PHY_LED_ON_LINK1000) ? ++ MTK_PHY_LED_BLINK_1000RX : 0) | ++ ((on & MTK_PHY_LED_ON_LINK2500) ? ++ MTK_PHY_LED_BLINK_2500RX : 0)) : ++ rx_blink_set; ++ } ++ ++ if (rules & BIT(TRIGGER_NETDEV_TX)) { ++ blink |= (on & on_set) ? ++ (((on & MTK_PHY_LED_ON_LINK10) ? ++ MTK_PHY_LED_BLINK_10TX : 0) | ++ ((on & MTK_PHY_LED_ON_LINK100) ? ++ MTK_PHY_LED_BLINK_100TX : 0) | ++ ((on & MTK_PHY_LED_ON_LINK1000) ? ++ MTK_PHY_LED_BLINK_1000TX : 0) | ++ ((on & MTK_PHY_LED_ON_LINK2500) ? ++ MTK_PHY_LED_BLINK_2500TX : 0)) : ++ tx_blink_set; ++ } ++ ++ if (blink || on) ++ set_bit(bit_netdev, led_state); ++ else ++ clear_bit(bit_netdev, led_state); ++ ++ ret = phy_modify_mmd(phydev, MDIO_MMD_VEND2, index ? ++ MTK_PHY_LED1_ON_CTRL : MTK_PHY_LED0_ON_CTRL, ++ MTK_PHY_LED_ON_FDX | MTK_PHY_LED_ON_HDX | on_set, ++ on); ++ ++ if (ret) ++ return ret; ++ ++ return phy_write_mmd(phydev, MDIO_MMD_VEND2, index ? ++ MTK_PHY_LED1_BLINK_CTRL : ++ MTK_PHY_LED0_BLINK_CTRL, blink); ++} ++EXPORT_SYMBOL_GPL(mtk_phy_led_hw_ctrl_set); ++ ++int mtk_phy_led_num_dly_cfg(u8 index, unsigned long *delay_on, ++ unsigned long *delay_off, bool *blinking) ++{ ++ if (index > 1) ++ return -EINVAL; ++ ++ if (delay_on && delay_off && (*delay_on > 0) && (*delay_off > 0)) { ++ *blinking = true; ++ *delay_on = 50; ++ *delay_off = 50; ++ } ++ ++ return 0; ++} ++EXPORT_SYMBOL_GPL(mtk_phy_led_num_dly_cfg); ++ ++int mtk_phy_hw_led_on_set(struct phy_device *phydev, u8 index, ++ unsigned long *led_state, u16 led_on_mask, bool on) ++{ ++ unsigned int bit_on = MTK_PHY_LED_STATE_FORCE_ON + (index ? 16 : 0); ++ bool changed; ++ ++ if (on) ++ changed = !test_and_set_bit(bit_on, led_state); ++ else ++ changed = !!test_and_clear_bit(bit_on, led_state); ++ ++ changed |= !!test_and_clear_bit(MTK_PHY_LED_STATE_NETDEV + ++ (index ? 16 : 0), led_state); ++ if (changed) ++ return phy_modify_mmd(phydev, MDIO_MMD_VEND2, index ? ++ MTK_PHY_LED1_ON_CTRL : ++ MTK_PHY_LED0_ON_CTRL, ++ led_on_mask, ++ on ? MTK_PHY_LED_ON_FORCE_ON : 0); ++ else ++ return 0; ++} ++EXPORT_SYMBOL_GPL(mtk_phy_hw_led_on_set); ++ ++int mtk_phy_hw_led_blink_set(struct phy_device *phydev, u8 index, ++ unsigned long *led_state, bool blinking) ++{ ++ unsigned int bit_blink = MTK_PHY_LED_STATE_FORCE_BLINK + ++ (index ? 16 : 0); ++ bool changed; ++ ++ if (blinking) ++ changed = !test_and_set_bit(bit_blink, led_state); ++ else ++ changed = !!test_and_clear_bit(bit_blink, led_state); ++ ++ changed |= !!test_bit(MTK_PHY_LED_STATE_NETDEV + ++ (index ? 16 : 0), led_state); ++ if (changed) ++ return phy_write_mmd(phydev, MDIO_MMD_VEND2, index ? ++ MTK_PHY_LED1_BLINK_CTRL : ++ MTK_PHY_LED0_BLINK_CTRL, ++ blinking ? ++ MTK_PHY_LED_BLINK_FORCE_BLINK : 0); ++ else ++ return 0; ++} ++EXPORT_SYMBOL_GPL(mtk_phy_hw_led_blink_set); ++ ++void mtk_phy_leds_state_init(struct phy_device *phydev) ++{ ++ int i; ++ ++ for (i = 0; i < 2; ++i) ++ phydev->drv->led_hw_control_get(phydev, i, NULL); ++} ++EXPORT_SYMBOL_GPL(mtk_phy_leds_state_init); ++ ++MODULE_DESCRIPTION("MediaTek Ethernet PHY driver common"); ++MODULE_AUTHOR("Sky Huang "); ++MODULE_AUTHOR("Daniel Golle "); ++MODULE_LICENSE("GPL"); +--- /dev/null ++++ b/drivers/net/phy/mediatek/mtk.h +@@ -0,0 +1,82 @@ ++/* SPDX-License-Identifier: GPL-2.0 ++ * ++ * Common definition for Mediatek Ethernet PHYs ++ * Author: SkyLake Huang ++ * Copyright (c) 2024 MediaTek Inc. ++ */ ++ ++#ifndef _MTK_EPHY_H_ ++#define _MTK_EPHY_H_ ++ ++#define MTK_EXT_PAGE_ACCESS 0x1f ++ ++/* Registers on MDIO_MMD_VEND2 */ ++#define MTK_PHY_LED0_ON_CTRL 0x24 ++#define MTK_PHY_LED1_ON_CTRL 0x26 ++#define MTK_GPHY_LED_ON_MASK GENMASK(6, 0) ++#define MTK_2P5GPHY_LED_ON_MASK GENMASK(7, 0) ++#define MTK_PHY_LED_ON_LINK1000 BIT(0) ++#define MTK_PHY_LED_ON_LINK100 BIT(1) ++#define MTK_PHY_LED_ON_LINK10 BIT(2) ++#define MTK_PHY_LED_ON_LINKDOWN BIT(3) ++#define MTK_PHY_LED_ON_FDX BIT(4) /* Full duplex */ ++#define MTK_PHY_LED_ON_HDX BIT(5) /* Half duplex */ ++#define MTK_PHY_LED_ON_FORCE_ON BIT(6) ++#define MTK_PHY_LED_ON_LINK2500 BIT(7) ++#define MTK_PHY_LED_ON_POLARITY BIT(14) ++#define MTK_PHY_LED_ON_ENABLE BIT(15) ++ ++#define MTK_PHY_LED0_BLINK_CTRL 0x25 ++#define MTK_PHY_LED1_BLINK_CTRL 0x27 ++#define MTK_PHY_LED_BLINK_1000TX BIT(0) ++#define MTK_PHY_LED_BLINK_1000RX BIT(1) ++#define MTK_PHY_LED_BLINK_100TX BIT(2) ++#define MTK_PHY_LED_BLINK_100RX BIT(3) ++#define MTK_PHY_LED_BLINK_10TX BIT(4) ++#define MTK_PHY_LED_BLINK_10RX BIT(5) ++#define MTK_PHY_LED_BLINK_COLLISION BIT(6) ++#define MTK_PHY_LED_BLINK_RX_CRC_ERR BIT(7) ++#define MTK_PHY_LED_BLINK_RX_IDLE_ERR BIT(8) ++#define MTK_PHY_LED_BLINK_FORCE_BLINK BIT(9) ++#define MTK_PHY_LED_BLINK_2500TX BIT(10) ++#define MTK_PHY_LED_BLINK_2500RX BIT(11) ++ ++#define MTK_GPHY_LED_ON_SET (MTK_PHY_LED_ON_LINK1000 | \ ++ MTK_PHY_LED_ON_LINK100 | \ ++ MTK_PHY_LED_ON_LINK10) ++#define MTK_GPHY_LED_RX_BLINK_SET (MTK_PHY_LED_BLINK_1000RX | \ ++ MTK_PHY_LED_BLINK_100RX | \ ++ MTK_PHY_LED_BLINK_10RX) ++#define MTK_GPHY_LED_TX_BLINK_SET (MTK_PHY_LED_BLINK_1000RX | \ ++ MTK_PHY_LED_BLINK_100RX | \ ++ MTK_PHY_LED_BLINK_10RX) ++ ++#define MTK_2P5GPHY_LED_ON_SET (MTK_PHY_LED_ON_LINK2500 | \ ++ MTK_GPHY_LED_ON_SET) ++#define MTK_2P5GPHY_LED_RX_BLINK_SET (MTK_PHY_LED_BLINK_2500RX | \ ++ MTK_GPHY_LED_RX_BLINK_SET) ++#define MTK_2P5GPHY_LED_TX_BLINK_SET (MTK_PHY_LED_BLINK_2500RX | \ ++ MTK_GPHY_LED_TX_BLINK_SET) ++ ++#define MTK_PHY_LED_STATE_FORCE_ON 0 ++#define MTK_PHY_LED_STATE_FORCE_BLINK 1 ++#define MTK_PHY_LED_STATE_NETDEV 2 ++ ++int mtk_phy_led_hw_is_supported(struct phy_device *phydev, u8 index, ++ unsigned long rules, ++ unsigned long supported_triggers); ++int mtk_phy_led_hw_ctrl_set(struct phy_device *phydev, u8 index, ++ unsigned long rules, unsigned long *led_state, ++ u16 on_set, u16 rx_blink_set, u16 tx_blink_set); ++int mtk_phy_led_hw_ctrl_get(struct phy_device *phydev, u8 index, ++ unsigned long *rules, unsigned long *led_state, ++ u16 on_set, u16 rx_blink_set, u16 tx_blink_set); ++int mtk_phy_led_num_dly_cfg(u8 index, unsigned long *delay_on, ++ unsigned long *delay_off, bool *blinking); ++int mtk_phy_hw_led_on_set(struct phy_device *phydev, u8 index, ++ unsigned long *led_state, u16 led_on_mask, bool on); ++int mtk_phy_hw_led_blink_set(struct phy_device *phydev, u8 index, ++ unsigned long *led_state, bool blinking); ++void mtk_phy_leds_state_init(struct phy_device *phydev); ++ ++#endif /* _MTK_EPHY_H_ */ diff --git a/target/linux/mediatek/patches-6.6/733-04-net-phy-mediatek-Improve-readability-of-mtk-phy-lib..patch b/target/linux/mediatek/patches-6.6/733-04-net-phy-mediatek-Improve-readability-of-mtk-phy-lib..patch new file mode 100644 index 0000000000..717dc890e3 --- /dev/null +++ b/target/linux/mediatek/patches-6.6/733-04-net-phy-mediatek-Improve-readability-of-mtk-phy-lib..patch @@ -0,0 +1,70 @@ +From 2783929879854d5750ba82e2e203663313362abb Mon Sep 17 00:00:00 2001 +From: "SkyLake.Huang" +Date: Mon, 1 Jul 2024 18:54:08 +0800 +Subject: [PATCH 04/13] net: phy: mediatek: Improve readability of + mtk-phy-lib.c's mtk_phy_led_hw_ctrl_set() + +This patch removes parens around TRIGGER_NETDEV_RX/TRIGGER_NETDEV_TX in +mtk_phy_led_hw_ctrl_set(), which improves readability. + +Signed-off-by: SkyLake.Huang +--- + drivers/net/phy/mediatek/mtk-phy-lib.c | 44 ++++++++++++++------------ + 1 file changed, 24 insertions(+), 20 deletions(-) + +--- a/drivers/net/phy/mediatek/mtk-phy-lib.c ++++ b/drivers/net/phy/mediatek/mtk-phy-lib.c +@@ -127,29 +127,33 @@ int mtk_phy_led_hw_ctrl_set(struct phy_d + on |= MTK_PHY_LED_ON_LINK2500; + + if (rules & BIT(TRIGGER_NETDEV_RX)) { +- blink |= (on & on_set) ? +- (((on & MTK_PHY_LED_ON_LINK10) ? +- MTK_PHY_LED_BLINK_10RX : 0) | +- ((on & MTK_PHY_LED_ON_LINK100) ? +- MTK_PHY_LED_BLINK_100RX : 0) | +- ((on & MTK_PHY_LED_ON_LINK1000) ? +- MTK_PHY_LED_BLINK_1000RX : 0) | +- ((on & MTK_PHY_LED_ON_LINK2500) ? +- MTK_PHY_LED_BLINK_2500RX : 0)) : +- rx_blink_set; ++ if (on & on_set) { ++ if (on & MTK_PHY_LED_ON_LINK10) ++ blink |= MTK_PHY_LED_BLINK_10RX; ++ if (on & MTK_PHY_LED_ON_LINK100) ++ blink |= MTK_PHY_LED_BLINK_100RX; ++ if (on & MTK_PHY_LED_ON_LINK1000) ++ blink |= MTK_PHY_LED_BLINK_1000RX; ++ if (on & MTK_PHY_LED_ON_LINK2500) ++ blink |= MTK_PHY_LED_BLINK_2500RX; ++ } else { ++ blink |= rx_blink_set; ++ } + } + + if (rules & BIT(TRIGGER_NETDEV_TX)) { +- blink |= (on & on_set) ? +- (((on & MTK_PHY_LED_ON_LINK10) ? +- MTK_PHY_LED_BLINK_10TX : 0) | +- ((on & MTK_PHY_LED_ON_LINK100) ? +- MTK_PHY_LED_BLINK_100TX : 0) | +- ((on & MTK_PHY_LED_ON_LINK1000) ? +- MTK_PHY_LED_BLINK_1000TX : 0) | +- ((on & MTK_PHY_LED_ON_LINK2500) ? +- MTK_PHY_LED_BLINK_2500TX : 0)) : +- tx_blink_set; ++ if (on & on_set) { ++ if (on & MTK_PHY_LED_ON_LINK10) ++ blink |= MTK_PHY_LED_BLINK_10TX; ++ if (on & MTK_PHY_LED_ON_LINK100) ++ blink |= MTK_PHY_LED_BLINK_100TX; ++ if (on & MTK_PHY_LED_ON_LINK1000) ++ blink |= MTK_PHY_LED_BLINK_1000TX; ++ if (on & MTK_PHY_LED_ON_LINK2500) ++ blink |= MTK_PHY_LED_BLINK_2500TX; ++ } else { ++ blink |= tx_blink_set; ++ } + } + + if (blink || on) diff --git a/target/linux/mediatek/patches-6.6/733-05-net-phy-mediatek-Integrate-read-write-page-helper-fu.patch b/target/linux/mediatek/patches-6.6/733-05-net-phy-mediatek-Integrate-read-write-page-helper-fu.patch new file mode 100644 index 0000000000..4a112a202c --- /dev/null +++ b/target/linux/mediatek/patches-6.6/733-05-net-phy-mediatek-Integrate-read-write-page-helper-fu.patch @@ -0,0 +1,141 @@ +From 58c1270423ab48464cdc31ef71ffe7f5b2441961 Mon Sep 17 00:00:00 2001 +From: "SkyLake.Huang" +Date: Mon, 1 Jul 2024 18:54:09 +0800 +Subject: [PATCH 05/13] net: phy: mediatek: Integrate read/write page helper + functions + +This patch integrates read/write page helper functions as MTK phy lib. +They are basically the same in mtk-ge.c & mtk-ge-soc.c. + +Signed-off-by: SkyLake.Huang +--- + drivers/net/phy/mediatek/mtk-ge-soc.c | 18 ++++-------------- + drivers/net/phy/mediatek/mtk-ge.c | 20 ++++++-------------- + drivers/net/phy/mediatek/mtk-phy-lib.c | 12 ++++++++++++ + drivers/net/phy/mediatek/mtk.h | 3 +++ + 4 files changed, 25 insertions(+), 28 deletions(-) + +--- a/drivers/net/phy/mediatek/mtk-ge-soc.c ++++ b/drivers/net/phy/mediatek/mtk-ge-soc.c +@@ -275,16 +275,6 @@ struct mtk_socphy_shared { + struct mtk_socphy_priv priv[4]; + }; + +-static int mtk_socphy_read_page(struct phy_device *phydev) +-{ +- return __phy_read(phydev, MTK_EXT_PAGE_ACCESS); +-} +- +-static int mtk_socphy_write_page(struct phy_device *phydev, int page) +-{ +- return __phy_write(phydev, MTK_EXT_PAGE_ACCESS, page); +-} +- + /* One calibration cycle consists of: + * 1.Set DA_CALIN_FLAG high to start calibration. Keep it high + * until AD_CAL_COMP is ready to output calibration result. +@@ -1305,8 +1295,8 @@ static struct phy_driver mtk_socphy_driv + .probe = mt7981_phy_probe, + .suspend = genphy_suspend, + .resume = genphy_resume, +- .read_page = mtk_socphy_read_page, +- .write_page = mtk_socphy_write_page, ++ .read_page = mtk_phy_read_page, ++ .write_page = mtk_phy_write_page, + .led_blink_set = mt798x_phy_led_blink_set, + .led_brightness_set = mt798x_phy_led_brightness_set, + .led_hw_is_supported = mt798x_phy_led_hw_is_supported, +@@ -1322,8 +1312,8 @@ static struct phy_driver mtk_socphy_driv + .probe = mt7988_phy_probe, + .suspend = genphy_suspend, + .resume = genphy_resume, +- .read_page = mtk_socphy_read_page, +- .write_page = mtk_socphy_write_page, ++ .read_page = mtk_phy_read_page, ++ .write_page = mtk_phy_write_page, + .led_blink_set = mt798x_phy_led_blink_set, + .led_brightness_set = mt798x_phy_led_brightness_set, + .led_hw_is_supported = mt798x_phy_led_hw_is_supported, +--- a/drivers/net/phy/mediatek/mtk-ge.c ++++ b/drivers/net/phy/mediatek/mtk-ge.c +@@ -4,6 +4,8 @@ + #include + #include + ++#include "mtk.h" ++ + #define MTK_EXT_PAGE_ACCESS 0x1f + #define MTK_PHY_PAGE_STANDARD 0x0000 + #define MTK_PHY_PAGE_EXTENDED 0x0001 +@@ -12,16 +14,6 @@ + #define MTK_PHY_PAGE_EXTENDED_2A30 0x2a30 + #define MTK_PHY_PAGE_EXTENDED_52B5 0x52b5 + +-static int mtk_gephy_read_page(struct phy_device *phydev) +-{ +- return __phy_read(phydev, MTK_EXT_PAGE_ACCESS); +-} +- +-static int mtk_gephy_write_page(struct phy_device *phydev, int page) +-{ +- return __phy_write(phydev, MTK_EXT_PAGE_ACCESS, page); +-} +- + static void mtk_gephy_config_init(struct phy_device *phydev) + { + /* Disable EEE */ +@@ -114,8 +106,8 @@ static struct phy_driver mtk_gephy_drive + .handle_interrupt = genphy_handle_interrupt_no_ack, + .suspend = genphy_suspend, + .resume = genphy_resume, +- .read_page = mtk_gephy_read_page, +- .write_page = mtk_gephy_write_page, ++ .read_page = mtk_phy_read_page, ++ .write_page = mtk_phy_write_page, + }, + { + PHY_ID_MATCH_EXACT(0x03a29441), +@@ -128,8 +120,8 @@ static struct phy_driver mtk_gephy_drive + .handle_interrupt = genphy_handle_interrupt_no_ack, + .suspend = genphy_suspend, + .resume = genphy_resume, +- .read_page = mtk_gephy_read_page, +- .write_page = mtk_gephy_write_page, ++ .read_page = mtk_phy_read_page, ++ .write_page = mtk_phy_write_page, + }, + }; + +--- a/drivers/net/phy/mediatek/mtk-phy-lib.c ++++ b/drivers/net/phy/mediatek/mtk-phy-lib.c +@@ -6,6 +6,18 @@ + + #include "mtk.h" + ++int mtk_phy_read_page(struct phy_device *phydev) ++{ ++ return __phy_read(phydev, MTK_EXT_PAGE_ACCESS); ++} ++EXPORT_SYMBOL_GPL(mtk_phy_read_page); ++ ++int mtk_phy_write_page(struct phy_device *phydev, int page) ++{ ++ return __phy_write(phydev, MTK_EXT_PAGE_ACCESS, page); ++} ++EXPORT_SYMBOL_GPL(mtk_phy_write_page); ++ + int mtk_phy_led_hw_is_supported(struct phy_device *phydev, u8 index, + unsigned long rules, + unsigned long supported_triggers) +--- a/drivers/net/phy/mediatek/mtk.h ++++ b/drivers/net/phy/mediatek/mtk.h +@@ -62,6 +62,9 @@ + #define MTK_PHY_LED_STATE_FORCE_BLINK 1 + #define MTK_PHY_LED_STATE_NETDEV 2 + ++int mtk_phy_read_page(struct phy_device *phydev); ++int mtk_phy_write_page(struct phy_device *phydev, int page); ++ + int mtk_phy_led_hw_is_supported(struct phy_device *phydev, u8 index, + unsigned long rules, + unsigned long supported_triggers); diff --git a/target/linux/mediatek/patches-6.6/733-06-net-phy-mediatek-Hook-LED-helper-functions-in-mtk-ge.patch b/target/linux/mediatek/patches-6.6/733-06-net-phy-mediatek-Hook-LED-helper-functions-in-mtk-ge.patch new file mode 100644 index 0000000000..485e262134 --- /dev/null +++ b/target/linux/mediatek/patches-6.6/733-06-net-phy-mediatek-Hook-LED-helper-functions-in-mtk-ge.patch @@ -0,0 +1,146 @@ +From 9403f1d54598ae56386a8bf47a5b6b34c884e4f5 Mon Sep 17 00:00:00 2001 +From: "SkyLake.Huang" +Date: Mon, 1 Jul 2024 18:54:10 +0800 +Subject: [PATCH 06/13] net: phy: mediatek: Hook LED helper functions in + mtk-ge.c + +We have mtk-phy-lib.c now so that we can use LED helper functions in +mtk-ge.c(mt7531 part). It also means that mt7531/mt7981/mt7988's +Giga ethernet phys share almost the same HW LED controller design. +Also, add probe function for mt7531 so that it can initialize LED state. + +Signed-off-by: SkyLake.Huang +--- + drivers/net/phy/mediatek/mtk-ge.c | 100 ++++++++++++++++++++++++++++++ + 1 file changed, 100 insertions(+) + +--- a/drivers/net/phy/mediatek/mtk-ge.c ++++ b/drivers/net/phy/mediatek/mtk-ge.c +@@ -14,6 +14,10 @@ + #define MTK_PHY_PAGE_EXTENDED_2A30 0x2a30 + #define MTK_PHY_PAGE_EXTENDED_52B5 0x52b5 + ++struct mtk_gephy_priv { ++ unsigned long led_state; ++}; ++ + static void mtk_gephy_config_init(struct phy_device *phydev) + { + /* Disable EEE */ +@@ -94,6 +98,96 @@ static int mt7531_phy_config_init(struct + return 0; + } + ++static int mt7531_phy_probe(struct phy_device *phydev) ++{ ++ struct mtk_gephy_priv *priv; ++ ++ priv = devm_kzalloc(&phydev->mdio.dev, sizeof(struct mtk_gephy_priv), ++ GFP_KERNEL); ++ if (!priv) ++ return -ENOMEM; ++ ++ phydev->priv = priv; ++ ++ mtk_phy_leds_state_init(phydev); ++ ++ return 0; ++} ++ ++static int mt753x_phy_led_blink_set(struct phy_device *phydev, u8 index, ++ unsigned long *delay_on, ++ unsigned long *delay_off) ++{ ++ struct mtk_gephy_priv *priv = phydev->priv; ++ bool blinking = false; ++ int err = 0; ++ ++ err = mtk_phy_led_num_dly_cfg(index, delay_on, delay_off, &blinking); ++ if (err < 0) ++ return err; ++ ++ err = mtk_phy_hw_led_blink_set(phydev, index, &priv->led_state, ++ blinking); ++ if (err) ++ return err; ++ ++ return mtk_phy_hw_led_on_set(phydev, index, &priv->led_state, ++ MTK_GPHY_LED_ON_MASK, false); ++} ++ ++static int mt753x_phy_led_brightness_set(struct phy_device *phydev, ++ u8 index, enum led_brightness value) ++{ ++ struct mtk_gephy_priv *priv = phydev->priv; ++ int err; ++ ++ err = mtk_phy_hw_led_blink_set(phydev, index, &priv->led_state, false); ++ if (err) ++ return err; ++ ++ return mtk_phy_hw_led_on_set(phydev, index, &priv->led_state, ++ MTK_GPHY_LED_ON_MASK, (value != LED_OFF)); ++} ++ ++static const unsigned long supported_triggers = ++ (BIT(TRIGGER_NETDEV_FULL_DUPLEX) | ++ BIT(TRIGGER_NETDEV_HALF_DUPLEX) | ++ BIT(TRIGGER_NETDEV_LINK) | ++ BIT(TRIGGER_NETDEV_LINK_10) | ++ BIT(TRIGGER_NETDEV_LINK_100) | ++ BIT(TRIGGER_NETDEV_LINK_1000) | ++ BIT(TRIGGER_NETDEV_RX) | ++ BIT(TRIGGER_NETDEV_TX)); ++ ++static int mt753x_phy_led_hw_is_supported(struct phy_device *phydev, u8 index, ++ unsigned long rules) ++{ ++ return mtk_phy_led_hw_is_supported(phydev, index, rules, ++ supported_triggers); ++} ++ ++static int mt753x_phy_led_hw_control_get(struct phy_device *phydev, u8 index, ++ unsigned long *rules) ++{ ++ struct mtk_gephy_priv *priv = phydev->priv; ++ ++ return mtk_phy_led_hw_ctrl_get(phydev, index, rules, &priv->led_state, ++ MTK_GPHY_LED_ON_SET, ++ MTK_GPHY_LED_RX_BLINK_SET, ++ MTK_GPHY_LED_TX_BLINK_SET); ++}; ++ ++static int mt753x_phy_led_hw_control_set(struct phy_device *phydev, u8 index, ++ unsigned long rules) ++{ ++ struct mtk_gephy_priv *priv = phydev->priv; ++ ++ return mtk_phy_led_hw_ctrl_set(phydev, index, rules, &priv->led_state, ++ MTK_GPHY_LED_ON_SET, ++ MTK_GPHY_LED_RX_BLINK_SET, ++ MTK_GPHY_LED_TX_BLINK_SET); ++}; ++ + static struct phy_driver mtk_gephy_driver[] = { + { + PHY_ID_MATCH_EXACT(0x03a29412), +@@ -112,6 +206,7 @@ static struct phy_driver mtk_gephy_drive + { + PHY_ID_MATCH_EXACT(0x03a29441), + .name = "MediaTek MT7531 PHY", ++ .probe = mt7531_phy_probe, + .config_init = mt7531_phy_config_init, + /* Interrupts are handled by the switch, not the PHY + * itself. +@@ -122,6 +217,11 @@ static struct phy_driver mtk_gephy_drive + .resume = genphy_resume, + .read_page = mtk_phy_read_page, + .write_page = mtk_phy_write_page, ++ .led_blink_set = mt753x_phy_led_blink_set, ++ .led_brightness_set = mt753x_phy_led_brightness_set, ++ .led_hw_is_supported = mt753x_phy_led_hw_is_supported, ++ .led_hw_control_set = mt753x_phy_led_hw_control_set, ++ .led_hw_control_get = mt753x_phy_led_hw_control_get, + }, + }; + diff --git a/target/linux/mediatek/patches-6.6/733-07-net-phy-mediatek-add-MT7530-MT7531-s-PHY-ID-macros.patch b/target/linux/mediatek/patches-6.6/733-07-net-phy-mediatek-add-MT7530-MT7531-s-PHY-ID-macros.patch new file mode 100644 index 0000000000..bfdf864f8d --- /dev/null +++ b/target/linux/mediatek/patches-6.6/733-07-net-phy-mediatek-add-MT7530-MT7531-s-PHY-ID-macros.patch @@ -0,0 +1,54 @@ +From 51ee83602dbb84716180d9b6e43f6bebb0c2d7bd Mon Sep 17 00:00:00 2001 +From: "SkyLake.Huang" +Date: Mon, 1 Jul 2024 18:54:11 +0800 +Subject: [PATCH 07/13] net: phy: mediatek: add MT7530 & MT7531's PHY ID macros + +This patch adds MT7530 & MT7531's PHY ID macros in mtk-ge.c so that +it follows the same rule of mtk-ge-soc.c. + +Signed-off-by: SkyLake.Huang +--- + drivers/net/phy/mediatek/mtk-ge.c | 11 +++++++---- + 1 file changed, 7 insertions(+), 4 deletions(-) + +--- a/drivers/net/phy/mediatek/mtk-ge.c ++++ b/drivers/net/phy/mediatek/mtk-ge.c +@@ -6,6 +6,9 @@ + + #include "mtk.h" + ++#define MTK_GPHY_ID_MT7530 0x03a29412 ++#define MTK_GPHY_ID_MT7531 0x03a29441 ++ + #define MTK_EXT_PAGE_ACCESS 0x1f + #define MTK_PHY_PAGE_STANDARD 0x0000 + #define MTK_PHY_PAGE_EXTENDED 0x0001 +@@ -190,7 +193,7 @@ static int mt753x_phy_led_hw_control_set + + static struct phy_driver mtk_gephy_driver[] = { + { +- PHY_ID_MATCH_EXACT(0x03a29412), ++ PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7530), + .name = "MediaTek MT7530 PHY", + .config_init = mt7530_phy_config_init, + /* Interrupts are handled by the switch, not the PHY +@@ -204,7 +207,7 @@ static struct phy_driver mtk_gephy_drive + .write_page = mtk_phy_write_page, + }, + { +- PHY_ID_MATCH_EXACT(0x03a29441), ++ PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7531), + .name = "MediaTek MT7531 PHY", + .probe = mt7531_phy_probe, + .config_init = mt7531_phy_config_init, +@@ -228,8 +231,8 @@ static struct phy_driver mtk_gephy_drive + module_phy_driver(mtk_gephy_driver); + + static struct mdio_device_id __maybe_unused mtk_gephy_tbl[] = { +- { PHY_ID_MATCH_EXACT(0x03a29441) }, +- { PHY_ID_MATCH_EXACT(0x03a29412) }, ++ { PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7530) }, ++ { PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7531) }, + { } + }; + diff --git a/target/linux/mediatek/patches-6.6/733-08-net-phy-mediatek-Change-mtk-ge-soc.c-line-wrapping.patch b/target/linux/mediatek/patches-6.6/733-08-net-phy-mediatek-Change-mtk-ge-soc.c-line-wrapping.patch new file mode 100644 index 0000000000..ca155e5012 --- /dev/null +++ b/target/linux/mediatek/patches-6.6/733-08-net-phy-mediatek-Change-mtk-ge-soc.c-line-wrapping.patch @@ -0,0 +1,182 @@ +From e73df692396b0d6bdcb2317299fa1e8e547f3446 Mon Sep 17 00:00:00 2001 +From: "SkyLake.Huang" +Date: Mon, 1 Jul 2024 18:54:12 +0800 +Subject: [PATCH 08/13] net: phy: mediatek: Change mtk-ge-soc.c line wrapping + +This patch shrinks mtk-ge-soc.c line wrapping to 80 characters. + +Signed-off-by: SkyLake.Huang +--- + drivers/net/phy/mediatek/mtk-ge-soc.c | 67 +++++++++++++++++---------- + 1 file changed, 42 insertions(+), 25 deletions(-) + +--- a/drivers/net/phy/mediatek/mtk-ge-soc.c ++++ b/drivers/net/phy/mediatek/mtk-ge-soc.c +@@ -295,7 +295,8 @@ static int cal_cycle(struct phy_device * + ret = phy_read_mmd_poll_timeout(phydev, MDIO_MMD_VEND1, + MTK_PHY_RG_AD_CAL_CLK, reg_val, + reg_val & MTK_PHY_DA_CAL_CLK, 500, +- ANALOG_INTERNAL_OPERATION_MAX_US, false); ++ ANALOG_INTERNAL_OPERATION_MAX_US, ++ false); + if (ret) { + phydev_err(phydev, "Calibration cycle timeout\n"); + return ret; +@@ -304,7 +305,7 @@ static int cal_cycle(struct phy_device * + phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_AD_CALIN, + MTK_PHY_DA_CALIN_FLAG); + ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_AD_CAL_COMP) >> +- MTK_PHY_AD_CAL_COMP_OUT_SHIFT; ++ MTK_PHY_AD_CAL_COMP_OUT_SHIFT; + phydev_dbg(phydev, "cal_val: 0x%x, ret: %d\n", cal_val, ret); + + return ret; +@@ -394,38 +395,46 @@ static int tx_amp_fill_result(struct phy + } + + phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TXVLD_DA_RG, +- MTK_PHY_DA_TX_I2MPB_A_GBE_MASK, (buf[0] + bias[0]) << 10); ++ MTK_PHY_DA_TX_I2MPB_A_GBE_MASK, ++ (buf[0] + bias[0]) << 10); + phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TXVLD_DA_RG, + MTK_PHY_DA_TX_I2MPB_A_TBT_MASK, buf[0] + bias[1]); + phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_A2, +- MTK_PHY_DA_TX_I2MPB_A_HBT_MASK, (buf[0] + bias[2]) << 10); ++ MTK_PHY_DA_TX_I2MPB_A_HBT_MASK, ++ (buf[0] + bias[2]) << 10); + phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_A2, + MTK_PHY_DA_TX_I2MPB_A_TST_MASK, buf[0] + bias[3]); + + phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_B1, +- MTK_PHY_DA_TX_I2MPB_B_GBE_MASK, (buf[1] + bias[4]) << 8); ++ MTK_PHY_DA_TX_I2MPB_B_GBE_MASK, ++ (buf[1] + bias[4]) << 8); + phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_B1, + MTK_PHY_DA_TX_I2MPB_B_TBT_MASK, buf[1] + bias[5]); + phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_B2, +- MTK_PHY_DA_TX_I2MPB_B_HBT_MASK, (buf[1] + bias[6]) << 8); ++ MTK_PHY_DA_TX_I2MPB_B_HBT_MASK, ++ (buf[1] + bias[6]) << 8); + phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_B2, + MTK_PHY_DA_TX_I2MPB_B_TST_MASK, buf[1] + bias[7]); + + phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_C1, +- MTK_PHY_DA_TX_I2MPB_C_GBE_MASK, (buf[2] + bias[8]) << 8); ++ MTK_PHY_DA_TX_I2MPB_C_GBE_MASK, ++ (buf[2] + bias[8]) << 8); + phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_C1, + MTK_PHY_DA_TX_I2MPB_C_TBT_MASK, buf[2] + bias[9]); + phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_C2, +- MTK_PHY_DA_TX_I2MPB_C_HBT_MASK, (buf[2] + bias[10]) << 8); ++ MTK_PHY_DA_TX_I2MPB_C_HBT_MASK, ++ (buf[2] + bias[10]) << 8); + phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_C2, + MTK_PHY_DA_TX_I2MPB_C_TST_MASK, buf[2] + bias[11]); + + phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_D1, +- MTK_PHY_DA_TX_I2MPB_D_GBE_MASK, (buf[3] + bias[12]) << 8); ++ MTK_PHY_DA_TX_I2MPB_D_GBE_MASK, ++ (buf[3] + bias[12]) << 8); + phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_D1, + MTK_PHY_DA_TX_I2MPB_D_TBT_MASK, buf[3] + bias[13]); + phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_D2, +- MTK_PHY_DA_TX_I2MPB_D_HBT_MASK, (buf[3] + bias[14]) << 8); ++ MTK_PHY_DA_TX_I2MPB_D_HBT_MASK, ++ (buf[3] + bias[14]) << 8); + phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_D2, + MTK_PHY_DA_TX_I2MPB_D_TST_MASK, buf[3] + bias[15]); + +@@ -616,7 +625,8 @@ static int tx_vcm_cal_sw(struct phy_devi + goto restore; + + /* We calibrate TX-VCM in different logic. Check upper index and then +- * lower index. If this calibration is valid, apply lower index's result. ++ * lower index. If this calibration is valid, apply lower index's ++ * result. + */ + ret = upper_ret - lower_ret; + if (ret == 1) { +@@ -645,7 +655,8 @@ static int tx_vcm_cal_sw(struct phy_devi + } else if (upper_idx == TXRESERVE_MAX && upper_ret == 0 && + lower_ret == 0) { + ret = 0; +- phydev_warn(phydev, "TX-VCM SW cal result at high margin 0x%x\n", ++ phydev_warn(phydev, ++ "TX-VCM SW cal result at high margin 0x%x\n", + upper_idx); + } else { + ret = -EINVAL; +@@ -749,7 +760,8 @@ static void mt7981_phy_finetune(struct p + + /* TR_OPEN_LOOP_EN = 1, lpf_x_average = 9 */ + phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG234, +- MTK_PHY_TR_OPEN_LOOP_EN_MASK | MTK_PHY_LPF_X_AVERAGE_MASK, ++ MTK_PHY_TR_OPEN_LOOP_EN_MASK | ++ MTK_PHY_LPF_X_AVERAGE_MASK, + BIT(0) | FIELD_PREP(MTK_PHY_LPF_X_AVERAGE_MASK, 0x9)); + + /* rg_tr_lpf_cnt_val = 512 */ +@@ -818,7 +830,8 @@ static void mt7988_phy_finetune(struct p + + /* TR_OPEN_LOOP_EN = 1, lpf_x_average = 10 */ + phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG234, +- MTK_PHY_TR_OPEN_LOOP_EN_MASK | MTK_PHY_LPF_X_AVERAGE_MASK, ++ MTK_PHY_TR_OPEN_LOOP_EN_MASK | ++ MTK_PHY_LPF_X_AVERAGE_MASK, + BIT(0) | FIELD_PREP(MTK_PHY_LPF_X_AVERAGE_MASK, 0xa)); + + /* rg_tr_lpf_cnt_val = 1023 */ +@@ -930,7 +943,8 @@ static void mt798x_phy_eee(struct phy_de + phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); + + phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_3); +- __phy_modify(phydev, MTK_PHY_LPI_REG_14, MTK_PHY_LPI_WAKE_TIMER_1000_MASK, ++ __phy_modify(phydev, MTK_PHY_LPI_REG_14, ++ MTK_PHY_LPI_WAKE_TIMER_1000_MASK, + FIELD_PREP(MTK_PHY_LPI_WAKE_TIMER_1000_MASK, 0x19c)); + + __phy_modify(phydev, MTK_PHY_LPI_REG_1c, MTK_PHY_SMI_DET_ON_THRESH_MASK, +@@ -940,7 +954,8 @@ static void mt798x_phy_eee(struct phy_de + phy_modify_mmd(phydev, MDIO_MMD_VEND1, + MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG122, + MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK, +- FIELD_PREP(MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK, 0xff)); ++ FIELD_PREP(MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK, ++ 0xff)); + } + + static int cal_sw(struct phy_device *phydev, enum CAL_ITEM cal_item, +@@ -1119,14 +1134,15 @@ static int mt798x_phy_led_brightness_set + MTK_GPHY_LED_ON_MASK, (value != LED_OFF)); + } + +-static const unsigned long supported_triggers = (BIT(TRIGGER_NETDEV_FULL_DUPLEX) | +- BIT(TRIGGER_NETDEV_HALF_DUPLEX) | +- BIT(TRIGGER_NETDEV_LINK) | +- BIT(TRIGGER_NETDEV_LINK_10) | +- BIT(TRIGGER_NETDEV_LINK_100) | +- BIT(TRIGGER_NETDEV_LINK_1000) | +- BIT(TRIGGER_NETDEV_RX) | +- BIT(TRIGGER_NETDEV_TX)); ++static const unsigned long supported_triggers = ++ (BIT(TRIGGER_NETDEV_FULL_DUPLEX) | ++ BIT(TRIGGER_NETDEV_HALF_DUPLEX) | ++ BIT(TRIGGER_NETDEV_LINK) | ++ BIT(TRIGGER_NETDEV_LINK_10) | ++ BIT(TRIGGER_NETDEV_LINK_100) | ++ BIT(TRIGGER_NETDEV_LINK_1000) | ++ BIT(TRIGGER_NETDEV_RX) | ++ BIT(TRIGGER_NETDEV_TX)); + + static int mt798x_phy_led_hw_is_supported(struct phy_device *phydev, u8 index, + unsigned long rules) +@@ -1189,7 +1205,8 @@ static int mt7988_phy_fix_leds_polaritie + /* Only now setup pinctrl to avoid bogus blinking */ + pinctrl = devm_pinctrl_get_select(&phydev->mdio.dev, "gbe-led"); + if (IS_ERR(pinctrl)) +- dev_err(&phydev->mdio.bus->dev, "Failed to setup PHY LED pinctrl\n"); ++ dev_err(&phydev->mdio.bus->dev, ++ "Failed to setup PHY LED pinctrl\n"); + + return 0; + } diff --git a/target/linux/mediatek/patches-6.6/733-09-net-phy-mediatek-Add-token-ring-access-helper-functi.patch b/target/linux/mediatek/patches-6.6/733-09-net-phy-mediatek-Add-token-ring-access-helper-functi.patch new file mode 100644 index 0000000000..49e4c2057f --- /dev/null +++ b/target/linux/mediatek/patches-6.6/733-09-net-phy-mediatek-Add-token-ring-access-helper-functi.patch @@ -0,0 +1,614 @@ +From 60228de48d8bfde62b4db5945314e6a62079f091 Mon Sep 17 00:00:00 2001 +From: "SkyLake.Huang" +Date: Mon, 1 Jul 2024 18:54:13 +0800 +Subject: [PATCH 09/13] net: phy: mediatek: Add token ring access helper + functions in mtk-phy-lib + +This patch adds TR(token ring) manipulations and adds correct +macro names for those magic numbers. TR is a way to access +proprietary registers on page 52b5. Use these helper functions +so we can see which fields we're going to modify/set/clear. + +This patch doesn't really change registers' settings but just +enhances readability and maintainability. + +Signed-off-by: SkyLake.Huang +--- + drivers/net/phy/mediatek/mtk-ge-soc.c | 297 ++++++++++++++++--------- + drivers/net/phy/mediatek/mtk-ge.c | 82 +++++-- + drivers/net/phy/mediatek/mtk-phy-lib.c | 91 ++++++++ + drivers/net/phy/mediatek/mtk.h | 13 ++ + 4 files changed, 358 insertions(+), 125 deletions(-) + +--- a/drivers/net/phy/mediatek/mtk-ge-soc.c ++++ b/drivers/net/phy/mediatek/mtk-ge-soc.c +@@ -24,7 +24,108 @@ + #define MTK_PHY_SMI_DET_ON_THRESH_MASK GENMASK(13, 8) + + #define MTK_PHY_PAGE_EXTENDED_2A30 0x2a30 +-#define MTK_PHY_PAGE_EXTENDED_52B5 0x52b5 ++ ++/* Registers on Token Ring debug nodes */ ++/* ch_addr = 0x0, node_addr = 0x7, data_addr = 0x15 */ ++/* NormMseLoThresh */ ++#define NORMAL_MSE_LO_THRESH_MASK GENMASK(15, 8) ++ ++/* ch_addr = 0x0, node_addr = 0xf, data_addr = 0x3c */ ++/* RemAckCntLimitCtrl */ ++#define REMOTE_ACK_COUNT_LIMIT_CTRL_MASK GENMASK(2, 1) ++ ++/* ch_addr = 0x1, node_addr = 0xd, data_addr = 0x20 */ ++/* VcoSlicerThreshBitsHigh */ ++#define VCO_SLICER_THRESH_HIGH_MASK GENMASK(23, 0) ++ ++/* ch_addr = 0x1, node_addr = 0xf, data_addr = 0x0 */ ++/* DfeTailEnableVgaThresh1000 */ ++#define DFE_TAIL_EANBLE_VGA_TRHESH_1000 GENMASK(5, 1) ++ ++/* ch_addr = 0x1, node_addr = 0xf, data_addr = 0x1 */ ++/* MrvlTrFix100Kp */ ++#define MRVL_TR_FIX_100KP_MASK GENMASK(22, 20) ++/* MrvlTrFix100Kf */ ++#define MRVL_TR_FIX_100KF_MASK GENMASK(19, 17) ++/* MrvlTrFix1000Kp */ ++#define MRVL_TR_FIX_1000KP_MASK GENMASK(16, 14) ++/* MrvlTrFix1000Kf */ ++#define MRVL_TR_FIX_1000KF_MASK GENMASK(13, 11) ++ ++/* ch_addr = 0x1, node_addr = 0xf, data_addr = 0x12 */ ++/* VgaDecRate */ ++#define VGA_DECIMATION_RATE_MASK GENMASK(8, 5) ++ ++/* ch_addr = 0x1, node_addr = 0xf, data_addr = 0x17 */ ++/* SlvDSPreadyTime */ ++#define SLAVE_DSP_READY_TIME_MASK GENMASK(22, 15) ++/* MasDSPreadyTime */ ++#define MASTER_DSP_READY_TIME_MASK GENMASK(14, 7) ++ ++/* ch_addr = 0x1, node_addr = 0xf, data_addr = 0x18 */ ++/* EnabRandUpdTrig */ ++#define ENABLE_RANDOM_UPDOWN_COUNTER_TRIGGER BIT(8) ++ ++/* ch_addr = 0x1, node_addr = 0xf, data_addr = 0x20 */ ++/* ResetSyncOffset */ ++#define RESET_SYNC_OFFSET_MASK GENMASK(11, 8) ++ ++/* ch_addr = 0x2, node_addr = 0xd, data_addr = 0x0 */ ++/* FfeUpdGainForceVal */ ++#define FFE_UPDATE_GAIN_FORCE_VAL_MASK GENMASK(9, 7) ++/* FfeUpdGainForce */ ++#define FFE_UPDATE_GAIN_FORCE BIT(6) ++ ++/* ch_addr = 0x2, node_addr = 0xd, data_addr = 0x3 */ ++/* TrFreeze */ ++#define TR_FREEZE_MASK GENMASK(11, 0) ++ ++/* ch_addr = 0x2, node_addr = 0xd, data_addr = 0x6 */ ++/* SS: Steady-state, KP: Proportional Gain */ ++/* SSTrKp100 */ ++#define SS_TR_KP100_MASK GENMASK(21, 19) ++/* SSTrKf100 */ ++#define SS_TR_KF100_MASK GENMASK(18, 16) ++/* SSTrKp1000Mas */ ++#define SS_TR_KP1000_MASTER_MASK GENMASK(15, 13) ++/* SSTrKf1000Mas */ ++#define SS_TR_KF1000_MASTER_MASK GENMASK(12, 10) ++/* SSTrKp1000Slv */ ++#define SS_TR_KP1000_SLAVE_MASK GENMASK(9, 7) ++/* SSTrKf1000Slv */ ++#define SS_TR_KF1000_SLAVE_MASK GENMASK(6, 4) ++ ++/* ch_addr = 0x2, node_addr = 0xd, data_addr = 0x8 */ ++/* clear this bit if wanna select from AFE */ ++/* Regsigdet_sel_1000 */ ++#define EEE1000_SELECT_SIGNAL_DETECTION_FROM_DFE BIT(4) ++ ++/* ch_addr = 0x2, node_addr = 0xd, data_addr = 0xd */ ++/* RegEEE_st2TrKf1000 */ ++#define EEE1000_STAGE2_TR_KF_MASK GENMASK(13, 11) ++ ++/* ch_addr = 0x2, node_addr = 0xd, data_addr = 0xf */ ++/* RegEEE_slv_waketr_timer_tar */ ++#define SLAVE_WAKETR_TIMER_MASK GENMASK(20, 11) ++/* RegEEE_slv_remtx_timer_tar */ ++#define SLAVE_REMTX_TIMER_MASK GENMASK(10, 1) ++ ++/* ch_addr = 0x2, node_addr = 0xd, data_addr = 0x10 */ ++/* RegEEE_slv_wake_int_timer_tar */ ++#define SLAVE_WAKEINT_TIMER_MASK GENMASK(10, 1) ++ ++/* ch_addr = 0x2, node_addr = 0xd, data_addr = 0x14 */ ++/* RegEEE_trfreeze_timer2 */ ++#define TR_FREEZE_TIMER2_MASK GENMASK(9, 0) ++ ++/* ch_addr = 0x2, node_addr = 0xd, data_addr = 0x1c */ ++/* RegEEE100Stg1_tar */ ++#define EEE100_LPSYNC_STAGE1_UPDATE_TIMER_MASK GENMASK(8, 0) ++ ++/* ch_addr = 0x2, node_addr = 0xd, data_addr = 0x25 */ ++/* REGEEE_wake_slv_tr_wait_dfesigdet_en */ ++#define WAKE_SLAVE_TR_WAIT_DFE_DETECTION_EN BIT(11) ++ + + #define ANALOG_INTERNAL_OPERATION_MAX_US 20 + #define TXRESERVE_MIN 0 +@@ -679,40 +780,36 @@ restore: + static void mt798x_phy_common_finetune(struct phy_device *phydev) + { + phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); +- /* SlvDSPreadyTime = 24, MasDSPreadyTime = 24 */ +- __phy_write(phydev, 0x11, 0xc71); +- __phy_write(phydev, 0x12, 0xc); +- __phy_write(phydev, 0x10, 0x8fae); +- +- /* EnabRandUpdTrig = 1 */ +- __phy_write(phydev, 0x11, 0x2f00); +- __phy_write(phydev, 0x12, 0xe); +- __phy_write(phydev, 0x10, 0x8fb0); +- +- /* NormMseLoThresh = 85 */ +- __phy_write(phydev, 0x11, 0x55a0); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x83aa); +- +- /* FfeUpdGainForce = 1(Enable), FfeUpdGainForceVal = 4 */ +- __phy_write(phydev, 0x11, 0x240); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x9680); +- +- /* TrFreeze = 0 (mt7988 default) */ +- __phy_write(phydev, 0x11, 0x0); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x9686); +- +- /* SSTrKp100 = 5 */ +- /* SSTrKf100 = 6 */ +- /* SSTrKp1000Mas = 5 */ +- /* SSTrKf1000Mas = 6 */ +- /* SSTrKp1000Slv = 5 */ +- /* SSTrKf1000Slv = 6 */ +- __phy_write(phydev, 0x11, 0xbaef); +- __phy_write(phydev, 0x12, 0x2e); +- __phy_write(phydev, 0x10, 0x968c); ++ __mtk_tr_modify(phydev, 0x1, 0xf, 0x17, ++ SLAVE_DSP_READY_TIME_MASK | MASTER_DSP_READY_TIME_MASK, ++ FIELD_PREP(SLAVE_DSP_READY_TIME_MASK, 0x18) | ++ FIELD_PREP(MASTER_DSP_READY_TIME_MASK, 0x18)); ++ ++ __mtk_tr_set_bits(phydev, 0x1, 0xf, 0x18, ++ ENABLE_RANDOM_UPDOWN_COUNTER_TRIGGER); ++ ++ __mtk_tr_modify(phydev, 0x0, 0x7, 0x15, ++ NORMAL_MSE_LO_THRESH_MASK, ++ FIELD_PREP(NORMAL_MSE_LO_THRESH_MASK, 0x55)); ++ ++ __mtk_tr_modify(phydev, 0x2, 0xd, 0x0, ++ FFE_UPDATE_GAIN_FORCE_VAL_MASK, ++ FIELD_PREP(FFE_UPDATE_GAIN_FORCE_VAL_MASK, 0x4) | ++ FFE_UPDATE_GAIN_FORCE); ++ ++ __mtk_tr_clr_bits(phydev, 0x2, 0xd, 0x3, TR_FREEZE_MASK); ++ ++ __mtk_tr_modify(phydev, 0x2, 0xd, 0x6, ++ SS_TR_KP100_MASK | SS_TR_KF100_MASK | ++ SS_TR_KP1000_MASTER_MASK | SS_TR_KF1000_MASTER_MASK | ++ SS_TR_KP1000_SLAVE_MASK | SS_TR_KF1000_SLAVE_MASK, ++ FIELD_PREP(SS_TR_KP100_MASK, 0x5) | ++ FIELD_PREP(SS_TR_KF100_MASK, 0x6) | ++ FIELD_PREP(SS_TR_KP1000_MASTER_MASK, 0x5) | ++ FIELD_PREP(SS_TR_KF1000_MASTER_MASK, 0x6) | ++ FIELD_PREP(SS_TR_KP1000_SLAVE_MASK, 0x5) | ++ FIELD_PREP(SS_TR_KF1000_SLAVE_MASK, 0x6)); ++ + phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); + } + +@@ -735,27 +832,29 @@ static void mt7981_phy_finetune(struct p + } + + phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); +- /* ResetSyncOffset = 6 */ +- __phy_write(phydev, 0x11, 0x600); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x8fc0); +- +- /* VgaDecRate = 1 */ +- __phy_write(phydev, 0x11, 0x4c2a); +- __phy_write(phydev, 0x12, 0x3e); +- __phy_write(phydev, 0x10, 0x8fa4); ++ __mtk_tr_modify(phydev, 0x1, 0xf, 0x20, ++ RESET_SYNC_OFFSET_MASK, ++ FIELD_PREP(RESET_SYNC_OFFSET_MASK, 0x6)); ++ ++ __mtk_tr_modify(phydev, 0x1, 0xf, 0x12, ++ VGA_DECIMATION_RATE_MASK, ++ FIELD_PREP(VGA_DECIMATION_RATE_MASK, 0x1)); + + /* MrvlTrFix100Kp = 3, MrvlTrFix100Kf = 2, + * MrvlTrFix1000Kp = 3, MrvlTrFix1000Kf = 2 + */ +- __phy_write(phydev, 0x11, 0xd10a); +- __phy_write(phydev, 0x12, 0x34); +- __phy_write(phydev, 0x10, 0x8f82); ++ __mtk_tr_modify(phydev, 0x1, 0xf, 0x1, ++ MRVL_TR_FIX_100KP_MASK | MRVL_TR_FIX_100KF_MASK | ++ MRVL_TR_FIX_1000KP_MASK | MRVL_TR_FIX_1000KF_MASK, ++ FIELD_PREP(MRVL_TR_FIX_100KP_MASK, 0x3) | ++ FIELD_PREP(MRVL_TR_FIX_100KF_MASK, 0x2) | ++ FIELD_PREP(MRVL_TR_FIX_1000KP_MASK, 0x3) | ++ FIELD_PREP(MRVL_TR_FIX_1000KF_MASK, 0x2)); + + /* VcoSlicerThreshBitsHigh */ +- __phy_write(phydev, 0x11, 0x5555); +- __phy_write(phydev, 0x12, 0x55); +- __phy_write(phydev, 0x10, 0x8ec0); ++ __mtk_tr_modify(phydev, 0x1, 0xd, 0x20, ++ VCO_SLICER_THRESH_HIGH_MASK, ++ FIELD_PREP(VCO_SLICER_THRESH_HIGH_MASK, 0x555555)); + phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); + + /* TR_OPEN_LOOP_EN = 1, lpf_x_average = 9 */ +@@ -807,25 +906,23 @@ static void mt7988_phy_finetune(struct p + phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_TX_FILTER, 0x5); + + phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); +- /* ResetSyncOffset = 5 */ +- __phy_write(phydev, 0x11, 0x500); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x8fc0); ++ __mtk_tr_modify(phydev, 0x1, 0xf, 0x20, ++ RESET_SYNC_OFFSET_MASK, ++ FIELD_PREP(RESET_SYNC_OFFSET_MASK, 0x5)); + + /* VgaDecRate is 1 at default on mt7988 */ + +- /* MrvlTrFix100Kp = 6, MrvlTrFix100Kf = 7, +- * MrvlTrFix1000Kp = 6, MrvlTrFix1000Kf = 7 +- */ +- __phy_write(phydev, 0x11, 0xb90a); +- __phy_write(phydev, 0x12, 0x6f); +- __phy_write(phydev, 0x10, 0x8f82); +- +- /* RemAckCntLimitCtrl = 1 */ +- __phy_write(phydev, 0x11, 0xfbba); +- __phy_write(phydev, 0x12, 0xc3); +- __phy_write(phydev, 0x10, 0x87f8); +- ++ __mtk_tr_modify(phydev, 0x1, 0xf, 0x1, ++ MRVL_TR_FIX_100KP_MASK | MRVL_TR_FIX_100KF_MASK | ++ MRVL_TR_FIX_1000KP_MASK | MRVL_TR_FIX_1000KF_MASK, ++ FIELD_PREP(MRVL_TR_FIX_100KP_MASK, 0x6) | ++ FIELD_PREP(MRVL_TR_FIX_100KF_MASK, 0x7) | ++ FIELD_PREP(MRVL_TR_FIX_1000KP_MASK, 0x6) | ++ FIELD_PREP(MRVL_TR_FIX_1000KF_MASK, 0x7)); ++ ++ __mtk_tr_modify(phydev, 0x0, 0xf, 0x3c, ++ REMOTE_ACK_COUNT_LIMIT_CTRL_MASK, ++ FIELD_PREP(REMOTE_ACK_COUNT_LIMIT_CTRL_MASK, 0x1)); + phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); + + /* TR_OPEN_LOOP_EN = 1, lpf_x_average = 10 */ +@@ -901,45 +998,37 @@ static void mt798x_phy_eee(struct phy_de + MTK_PHY_TR_READY_SKIP_AFE_WAKEUP); + + phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); +- /* Regsigdet_sel_1000 = 0 */ +- __phy_write(phydev, 0x11, 0xb); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x9690); +- +- /* REG_EEE_st2TrKf1000 = 2 */ +- __phy_write(phydev, 0x11, 0x114f); +- __phy_write(phydev, 0x12, 0x2); +- __phy_write(phydev, 0x10, 0x969a); +- +- /* RegEEE_slv_wake_tr_timer_tar = 6, RegEEE_slv_remtx_timer_tar = 20 */ +- __phy_write(phydev, 0x11, 0x3028); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x969e); +- +- /* RegEEE_slv_wake_int_timer_tar = 8 */ +- __phy_write(phydev, 0x11, 0x5010); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x96a0); +- +- /* RegEEE_trfreeze_timer2 = 586 */ +- __phy_write(phydev, 0x11, 0x24a); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x96a8); +- +- /* RegEEE100Stg1_tar = 16 */ +- __phy_write(phydev, 0x11, 0x3210); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x96b8); +- +- /* REGEEE_wake_slv_tr_wait_dfesigdet_en = 0 */ +- __phy_write(phydev, 0x11, 0x1463); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x96ca); +- +- /* DfeTailEnableVgaThresh1000 = 27 */ +- __phy_write(phydev, 0x11, 0x36); +- __phy_write(phydev, 0x12, 0x0); +- __phy_write(phydev, 0x10, 0x8f80); ++ __mtk_tr_clr_bits(phydev, 0x2, 0xd, 0x8, ++ EEE1000_SELECT_SIGNAL_DETECTION_FROM_DFE); ++ ++ __mtk_tr_modify(phydev, 0x2, 0xd, 0xd, ++ EEE1000_STAGE2_TR_KF_MASK, ++ FIELD_PREP(EEE1000_STAGE2_TR_KF_MASK, 0x2)); ++ ++ __mtk_tr_modify(phydev, 0x2, 0xd, 0xf, ++ SLAVE_WAKETR_TIMER_MASK | SLAVE_REMTX_TIMER_MASK, ++ FIELD_PREP(SLAVE_WAKETR_TIMER_MASK, 0x6) | ++ FIELD_PREP(SLAVE_REMTX_TIMER_MASK, 0x14)); ++ ++ __mtk_tr_modify(phydev, 0x2, 0xd, 0x10, ++ SLAVE_WAKEINT_TIMER_MASK, ++ FIELD_PREP(SLAVE_WAKEINT_TIMER_MASK, 0x8)); ++ ++ __mtk_tr_modify(phydev, 0x2, 0xd, 0x14, ++ TR_FREEZE_TIMER2_MASK, ++ FIELD_PREP(TR_FREEZE_TIMER2_MASK, 0x24a)); ++ ++ __mtk_tr_modify(phydev, 0x2, 0xd, 0x1c, ++ EEE100_LPSYNC_STAGE1_UPDATE_TIMER_MASK, ++ FIELD_PREP(EEE100_LPSYNC_STAGE1_UPDATE_TIMER_MASK, ++ 0x10)); ++ ++ __mtk_tr_clr_bits(phydev, 0x2, 0xd, 0x25, ++ WAKE_SLAVE_TR_WAIT_DFE_DETECTION_EN); ++ ++ __mtk_tr_modify(phydev, 0x1, 0xf, 0x0, ++ DFE_TAIL_EANBLE_VGA_TRHESH_1000, ++ FIELD_PREP(DFE_TAIL_EANBLE_VGA_TRHESH_1000, 0x1b)); + phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); + + phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_3); +--- a/drivers/net/phy/mediatek/mtk-ge.c ++++ b/drivers/net/phy/mediatek/mtk-ge.c +@@ -9,13 +9,35 @@ + #define MTK_GPHY_ID_MT7530 0x03a29412 + #define MTK_GPHY_ID_MT7531 0x03a29441 + +-#define MTK_EXT_PAGE_ACCESS 0x1f +-#define MTK_PHY_PAGE_STANDARD 0x0000 +-#define MTK_PHY_PAGE_EXTENDED 0x0001 +-#define MTK_PHY_PAGE_EXTENDED_2 0x0002 +-#define MTK_PHY_PAGE_EXTENDED_3 0x0003 +-#define MTK_PHY_PAGE_EXTENDED_2A30 0x2a30 +-#define MTK_PHY_PAGE_EXTENDED_52B5 0x52b5 ++#define MTK_PHY_PAGE_EXTENDED_1 0x0001 ++#define MTK_PHY_AUX_CTRL_AND_STATUS 0x14 ++#define MTK_PHY_ENABLE_DOWNSHIFT BIT(4) ++ ++#define MTK_PHY_PAGE_EXTENDED_2 0x0002 ++#define MTK_PHY_PAGE_EXTENDED_3 0x0003 ++#define MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG11 0x11 ++ ++#define MTK_PHY_PAGE_EXTENDED_2A30 0x2a30 ++ ++/* Registers on Token Ring debug nodes */ ++/* ch_addr = 0x1, node_addr = 0xf, data_addr = 0x17 */ ++#define SLAVE_DSP_READY_TIME_MASK GENMASK(22, 15) ++ ++/* Registers on MDIO_MMD_VEND1 */ ++#define MTK_PHY_GBE_MODE_TX_DELAY_SEL 0x13 ++#define MTK_PHY_TEST_MODE_TX_DELAY_SEL 0x14 ++#define MTK_TX_DELAY_PAIR_B_MASK GENMASK(10, 8) ++#define MTK_TX_DELAY_PAIR_D_MASK GENMASK(2, 0) ++ ++#define MTK_PHY_MCC_CTRL_AND_TX_POWER_CTRL 0xa6 ++#define MTK_MCC_NEARECHO_OFFSET_MASK GENMASK(15, 8) ++ ++#define MTK_PHY_RXADC_CTRL_RG7 0xc6 ++#define MTK_PHY_DA_AD_BUF_BIAS_LP_MASK GENMASK(9, 8) ++ ++#define MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG123 0x123 ++#define MTK_PHY_LPI_NORM_MSE_LO_THRESH100_MASK GENMASK(15, 8) ++#define MTK_PHY_LPI_NORM_MSE_HI_THRESH100_MASK GENMASK(7, 0) + + struct mtk_gephy_priv { + unsigned long led_state; +@@ -27,20 +49,29 @@ static void mtk_gephy_config_init(struct + phy_write_mmd(phydev, MDIO_MMD_AN, MDIO_AN_EEE_ADV, 0); + + /* Enable HW auto downshift */ +- phy_modify_paged(phydev, MTK_PHY_PAGE_EXTENDED, 0x14, 0, BIT(4)); ++ phy_modify_paged(phydev, MTK_PHY_PAGE_EXTENDED_1, ++ MTK_PHY_AUX_CTRL_AND_STATUS, ++ 0, MTK_PHY_ENABLE_DOWNSHIFT); + + /* Increase SlvDPSready time */ +- phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); +- __phy_write(phydev, 0x10, 0xafae); +- __phy_write(phydev, 0x12, 0x2f); +- __phy_write(phydev, 0x10, 0x8fae); +- phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); ++ mtk_tr_modify(phydev, 0x1, 0xf, 0x17, SLAVE_DSP_READY_TIME_MASK, ++ FIELD_PREP(SLAVE_DSP_READY_TIME_MASK, 0x5e)); + + /* Adjust 100_mse_threshold */ +- phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x123, 0xffff); +- +- /* Disable mcc */ +- phy_write_mmd(phydev, MDIO_MMD_VEND1, 0xa6, 0x300); ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG123, ++ MTK_PHY_LPI_NORM_MSE_LO_THRESH100_MASK | ++ MTK_PHY_LPI_NORM_MSE_HI_THRESH100_MASK, ++ FIELD_PREP(MTK_PHY_LPI_NORM_MSE_LO_THRESH100_MASK, ++ 0xff) | ++ FIELD_PREP(MTK_PHY_LPI_NORM_MSE_HI_THRESH100_MASK, ++ 0xff)); ++ ++ /* If echo time is narrower than 0x3, it will be regarded as noise */ ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, ++ MTK_PHY_MCC_CTRL_AND_TX_POWER_CTRL, ++ MTK_MCC_NEARECHO_OFFSET_MASK, ++ FIELD_PREP(MTK_MCC_NEARECHO_OFFSET_MASK, 0x3)); + } + + static int mt7530_phy_config_init(struct phy_device *phydev) +@@ -48,7 +79,8 @@ static int mt7530_phy_config_init(struct + mtk_gephy_config_init(phydev); + + /* Increase post_update_timer */ +- phy_write_paged(phydev, MTK_PHY_PAGE_EXTENDED_3, 0x11, 0x4b); ++ phy_write_paged(phydev, MTK_PHY_PAGE_EXTENDED_3, ++ MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG11, 0x4b); + + return 0; + } +@@ -89,11 +121,19 @@ static int mt7531_phy_config_init(struct + + /* PHY link down power saving enable */ + phy_set_bits(phydev, 0x17, BIT(4)); +- phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, 0xc6, 0x300); ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RXADC_CTRL_RG7, ++ MTK_PHY_DA_AD_BUF_BIAS_LP_MASK, ++ FIELD_PREP(MTK_PHY_DA_AD_BUF_BIAS_LP_MASK, 0x3)); + + /* Set TX Pair delay selection */ +- phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x13, 0x404); +- phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x14, 0x404); ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_GBE_MODE_TX_DELAY_SEL, ++ MTK_TX_DELAY_PAIR_B_MASK | MTK_TX_DELAY_PAIR_D_MASK, ++ FIELD_PREP(MTK_TX_DELAY_PAIR_B_MASK, 0x4) | ++ FIELD_PREP(MTK_TX_DELAY_PAIR_D_MASK, 0x4)); ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TEST_MODE_TX_DELAY_SEL, ++ MTK_TX_DELAY_PAIR_B_MASK | MTK_TX_DELAY_PAIR_D_MASK, ++ FIELD_PREP(MTK_TX_DELAY_PAIR_B_MASK, 0x4) | ++ FIELD_PREP(MTK_TX_DELAY_PAIR_D_MASK, 0x4)); + + /* LED Config*/ + mt7530_led_config_of(phydev); +--- a/drivers/net/phy/mediatek/mtk-phy-lib.c ++++ b/drivers/net/phy/mediatek/mtk-phy-lib.c +@@ -6,6 +6,97 @@ + + #include "mtk.h" + ++/* Difference between functions with mtk_tr* and __mtk_tr* prefixes is ++ * mtk_tr* functions: wrapped by page switching operations ++ * __mtk_tr* functions: no page switching operations ++ */ ++ ++static void __mtk_tr_access(struct phy_device *phydev, bool read, u8 ch_addr, ++ u8 node_addr, u8 data_addr) ++{ ++ u16 tr_cmd = BIT(15); /* bit 14 & 0 are reserved */ ++ ++ if (read) ++ tr_cmd |= BIT(13); ++ ++ tr_cmd |= (((ch_addr & 0x3) << 11) | ++ ((node_addr & 0xf) << 7) | ++ ((data_addr & 0x3f) << 1)); ++ dev_dbg(&phydev->mdio.dev, "tr_cmd: 0x%x\n", tr_cmd); ++ __phy_write(phydev, 0x10, tr_cmd); ++} ++ ++static void __mtk_tr_read(struct phy_device *phydev, u8 ch_addr, u8 node_addr, ++ u8 data_addr, u16 *tr_high, u16 *tr_low) ++{ ++ __mtk_tr_access(phydev, true, ch_addr, node_addr, data_addr); ++ *tr_low = __phy_read(phydev, 0x11); ++ *tr_high = __phy_read(phydev, 0x12); ++ dev_dbg(&phydev->mdio.dev, "tr_high read: 0x%x, tr_low read: 0x%x\n", ++ *tr_high, *tr_low); ++} ++ ++u32 mtk_tr_read(struct phy_device *phydev, u8 ch_addr, u8 node_addr, ++ u8 data_addr) ++{ ++ u16 tr_high; ++ u16 tr_low; ++ ++ phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); ++ __mtk_tr_read(phydev, ch_addr, node_addr, data_addr, &tr_high, &tr_low); ++ phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); ++ ++ return (tr_high << 16) | tr_low; ++} ++EXPORT_SYMBOL_GPL(mtk_tr_read); ++ ++static void __mtk_tr_write(struct phy_device *phydev, u8 ch_addr, u8 node_addr, ++ u8 data_addr, u32 tr_data) ++{ ++ __phy_write(phydev, 0x11, tr_data & 0xffff); ++ __phy_write(phydev, 0x12, tr_data >> 16); ++ dev_dbg(&phydev->mdio.dev, "tr_high write: 0x%x, tr_low write: 0x%x\n", ++ tr_data >> 16, tr_data & 0xffff); ++ __mtk_tr_access(phydev, false, ch_addr, node_addr, data_addr); ++} ++ ++void __mtk_tr_modify(struct phy_device *phydev, u8 ch_addr, u8 node_addr, ++ u8 data_addr, u32 mask, u32 set) ++{ ++ u32 tr_data; ++ u16 tr_high; ++ u16 tr_low; ++ ++ __mtk_tr_read(phydev, ch_addr, node_addr, data_addr, &tr_high, &tr_low); ++ tr_data = (tr_high << 16) | tr_low; ++ tr_data = (tr_data & ~mask) | set; ++ __mtk_tr_write(phydev, ch_addr, node_addr, data_addr, tr_data); ++} ++EXPORT_SYMBOL_GPL(__mtk_tr_modify); ++ ++void mtk_tr_modify(struct phy_device *phydev, u8 ch_addr, u8 node_addr, ++ u8 data_addr, u32 mask, u32 set) ++{ ++ phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); ++ __mtk_tr_modify(phydev, ch_addr, node_addr, data_addr, mask, set); ++ phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); ++} ++EXPORT_SYMBOL_GPL(mtk_tr_modify); ++ ++void __mtk_tr_set_bits(struct phy_device *phydev, u8 ch_addr, u8 node_addr, ++ u8 data_addr, u32 set) ++{ ++ __mtk_tr_modify(phydev, ch_addr, node_addr, data_addr, 0, set); ++} ++EXPORT_SYMBOL_GPL(__mtk_tr_set_bits); ++ ++void __mtk_tr_clr_bits(struct phy_device *phydev, u8 ch_addr, u8 node_addr, ++ u8 data_addr, u32 clr) ++{ ++ __mtk_tr_modify(phydev, ch_addr, node_addr, data_addr, clr, 0); ++} ++EXPORT_SYMBOL_GPL(__mtk_tr_clr_bits); ++ + int mtk_phy_read_page(struct phy_device *phydev) + { + return __phy_read(phydev, MTK_EXT_PAGE_ACCESS); +--- a/drivers/net/phy/mediatek/mtk.h ++++ b/drivers/net/phy/mediatek/mtk.h +@@ -9,6 +9,8 @@ + #define _MTK_EPHY_H_ + + #define MTK_EXT_PAGE_ACCESS 0x1f ++#define MTK_PHY_PAGE_STANDARD 0x0000 ++#define MTK_PHY_PAGE_EXTENDED_52B5 0x52b5 + + /* Registers on MDIO_MMD_VEND2 */ + #define MTK_PHY_LED0_ON_CTRL 0x24 +@@ -62,6 +64,17 @@ + #define MTK_PHY_LED_STATE_FORCE_BLINK 1 + #define MTK_PHY_LED_STATE_NETDEV 2 + ++u32 mtk_tr_read(struct phy_device *phydev, u8 ch_addr, u8 node_addr, ++ u8 data_addr); ++void __mtk_tr_modify(struct phy_device *phydev, u8 ch_addr, u8 node_addr, ++ u8 data_addr, u32 mask, u32 set); ++void mtk_tr_modify(struct phy_device *phydev, u8 ch_addr, u8 node_addr, ++ u8 data_addr, u32 mask, u32 set); ++void __mtk_tr_set_bits(struct phy_device *phydev, u8 ch_addr, u8 node_addr, ++ u8 data_addr, u32 set); ++void __mtk_tr_clr_bits(struct phy_device *phydev, u8 ch_addr, u8 node_addr, ++ u8 data_addr, u32 clr); ++ + int mtk_phy_read_page(struct phy_device *phydev); + int mtk_phy_write_page(struct phy_device *phydev, int page); + diff --git a/target/linux/mediatek/patches-6.6/733-10-net-phy-mediatek-Extend-1G-TX-RX-link-pulse-time.patch b/target/linux/mediatek/patches-6.6/733-10-net-phy-mediatek-Extend-1G-TX-RX-link-pulse-time.patch new file mode 100644 index 0000000000..dcbe957836 --- /dev/null +++ b/target/linux/mediatek/patches-6.6/733-10-net-phy-mediatek-Extend-1G-TX-RX-link-pulse-time.patch @@ -0,0 +1,209 @@ +From 3c05195fc2c232cd853fc8cebf55310c4605111d Mon Sep 17 00:00:00 2001 +From: "SkyLake.Huang" +Date: Mon, 1 Jul 2024 18:54:14 +0800 +Subject: [PATCH 10/13] net: phy: mediatek: Extend 1G TX/RX link pulse time + +We observe that some 10G devices' (mostly Marvell's chips inside) 1G +training time violates specification, which may last 2230ms and affect +later TX/RX link pulse time. This will invalidate MediaTek series +gigabit Ethernet PHYs' hardware auto downshift mechanism. + +Without this patch, if someone is trying to use "4-wire" cable to +connect above devices, MediaTek' gigabit Ethernet PHYs may fail +to downshift to 100Mbps. (If partner 10G devices' downshift mechanism +stops at 1G) + +This patch extends our 1G TX/RX link pulse time so that we can still +link up with those 10G devices. + +Tested device: +- Netgear GS110EMX's 10G port (Marvell 88X3340P) +- QNAP QSW-M408-4C + +Signed-off-by: SkyLake.Huang +--- + drivers/net/phy/mediatek/mtk-ge-soc.c | 2 + + drivers/net/phy/mediatek/mtk-ge.c | 5 +- + drivers/net/phy/mediatek/mtk-phy-lib.c | 92 ++++++++++++++++++++++++++ + drivers/net/phy/mediatek/mtk.h | 21 ++++++ + 4 files changed, 116 insertions(+), 4 deletions(-) + +--- a/drivers/net/phy/mediatek/mtk-ge-soc.c ++++ b/drivers/net/phy/mediatek/mtk-ge-soc.c +@@ -1396,6 +1396,7 @@ static struct phy_driver mtk_socphy_driv + PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7981), + .name = "MediaTek MT7981 PHY", + .config_init = mt798x_phy_config_init, ++ .read_status = mtk_gphy_cl22_read_status, + .config_intr = genphy_no_config_intr, + .handle_interrupt = genphy_handle_interrupt_no_ack, + .probe = mt7981_phy_probe, +@@ -1413,6 +1414,7 @@ static struct phy_driver mtk_socphy_driv + PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7988), + .name = "MediaTek MT7988 PHY", + .config_init = mt798x_phy_config_init, ++ .read_status = mtk_gphy_cl22_read_status, + .config_intr = genphy_no_config_intr, + .handle_interrupt = genphy_handle_interrupt_no_ack, + .probe = mt7988_phy_probe, +--- a/drivers/net/phy/mediatek/mtk-ge.c ++++ b/drivers/net/phy/mediatek/mtk-ge.c +@@ -9,10 +9,6 @@ + #define MTK_GPHY_ID_MT7530 0x03a29412 + #define MTK_GPHY_ID_MT7531 0x03a29441 + +-#define MTK_PHY_PAGE_EXTENDED_1 0x0001 +-#define MTK_PHY_AUX_CTRL_AND_STATUS 0x14 +-#define MTK_PHY_ENABLE_DOWNSHIFT BIT(4) +- + #define MTK_PHY_PAGE_EXTENDED_2 0x0002 + #define MTK_PHY_PAGE_EXTENDED_3 0x0003 + #define MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG11 0x11 +@@ -251,6 +247,7 @@ static struct phy_driver mtk_gephy_drive + .name = "MediaTek MT7531 PHY", + .probe = mt7531_phy_probe, + .config_init = mt7531_phy_config_init, ++ .read_status = mtk_gphy_cl22_read_status, + /* Interrupts are handled by the switch, not the PHY + * itself. + */ +--- a/drivers/net/phy/mediatek/mtk-phy-lib.c ++++ b/drivers/net/phy/mediatek/mtk-phy-lib.c +@@ -109,6 +109,98 @@ int mtk_phy_write_page(struct phy_device + } + EXPORT_SYMBOL_GPL(mtk_phy_write_page); + ++/* This function deals with the case that 1G AN starts but isn't completed. We ++ * set AN_NEW_LP_CNT_LIMIT with different values time after time to let our ++ * 1G->100Mbps hardware automatic downshift to fit more partner devices. ++ */ ++static int extend_an_new_lp_cnt_limit(struct phy_device *phydev) ++{ ++ int mmd_read_ret; ++ u32 reg_val; ++ int timeout; ++ ++ /* According to table 28-9 & Figure 28-18 in IEEE 802.3, ++ * link_fail_inhibit_timer of 10/100/1000 Mbps devices ranges from 750 ++ * to "1000ms". Once MTK_PHY_FINAL_SPEED_1000 is set, it means that we ++ * enter "FLP LINK GOOD CHECK" state, link_fail_inhibit_timer starts and ++ * this PHY's 1G training starts. If 1G training never starts, we do ++ * nothing but leave. ++ */ ++ timeout = read_poll_timeout(mmd_read_ret = phy_read_mmd, reg_val, ++ (mmd_read_ret < 0) || ++ reg_val & MTK_PHY_FINAL_SPEED_1000, ++ 10000, 1000000, false, phydev, ++ MDIO_MMD_VEND1, MTK_PHY_LINK_STATUS_MISC); ++ if (mmd_read_ret < 0) ++ return mmd_read_ret; ++ ++ if (!timeout) { ++ /* Once we found MTK_PHY_FINAL_SPEED_1000 is set, no matter 1G ++ * AN is completed or not, we'll set AN_NEW_LP_CNT_LIMIT again ++ * and again. ++ */ ++ mtk_tr_modify(phydev, 0x0, 0xf, 0x3c, AN_NEW_LP_CNT_LIMIT_MASK, ++ FIELD_PREP(AN_NEW_LP_CNT_LIMIT_MASK, 0xf)); ++ mdelay(1500); ++ ++ timeout = read_poll_timeout(mtk_tr_read, reg_val, ++ (reg_val & AN_STATE_MASK) != ++ (AN_STATE_TX_DISABLE << ++ AN_STATE_SHIFT), ++ 10000, 1000000, false, phydev, ++ 0x0, 0xf, 0x2); ++ if (!timeout) { ++ mdelay(625); ++ mtk_tr_modify(phydev, 0x0, 0xf, 0x3c, ++ AN_NEW_LP_CNT_LIMIT_MASK, ++ FIELD_PREP(AN_NEW_LP_CNT_LIMIT_MASK, ++ 0x8)); ++ mdelay(500); ++ mtk_tr_modify(phydev, 0x0, 0xf, 0x3c, ++ AN_NEW_LP_CNT_LIMIT_MASK, ++ FIELD_PREP(AN_NEW_LP_CNT_LIMIT_MASK, ++ 0xf)); ++ } else { ++ return -ETIMEDOUT; ++ } ++ } ++ ++ return 0; ++} ++ ++int mtk_gphy_cl22_read_status(struct phy_device *phydev) ++{ ++ int ret; ++ ++ ret = genphy_read_status(phydev); ++ if (ret) ++ return ret; ++ ++ if (phydev->autoneg == AUTONEG_ENABLE && !phydev->autoneg_complete) { ++ ret = phy_read_paged(phydev, MTK_PHY_PAGE_EXTENDED_1, ++ MTK_PHY_AUX_CTRL_AND_STATUS); ++ if (ret < 0) ++ return ret; ++ ++ /* Once LP_DETECTED is set, it means that"ability_match" in ++ * IEEE 802.3 Figure 28-18 is set. This happens after we plug in ++ * cable. Also, LP_DETECTED will be cleared after AN complete. ++ */ ++ if (!FIELD_GET(MTK_PHY_LP_DETECTED_MASK, ret)) ++ return 0; ++ ++ ret = phy_read(phydev, MII_CTRL1000); ++ if (ret & (ADVERTISE_1000FULL | ADVERTISE_1000HALF)) { ++ ret = extend_an_new_lp_cnt_limit(phydev); ++ if (ret < 0) ++ return ret; ++ } ++ } ++ ++ return 0; ++} ++EXPORT_SYMBOL_GPL(mtk_gphy_cl22_read_status); ++ + int mtk_phy_led_hw_is_supported(struct phy_device *phydev, u8 index, + unsigned long rules, + unsigned long supported_triggers) +--- a/drivers/net/phy/mediatek/mtk.h ++++ b/drivers/net/phy/mediatek/mtk.h +@@ -10,8 +10,28 @@ + + #define MTK_EXT_PAGE_ACCESS 0x1f + #define MTK_PHY_PAGE_STANDARD 0x0000 ++#define MTK_PHY_PAGE_EXTENDED_1 0x0001 ++#define MTK_PHY_AUX_CTRL_AND_STATUS 0x14 ++/* suprv_media_select_RefClk */ ++#define MTK_PHY_LP_DETECTED_MASK GENMASK(7, 6) ++#define MTK_PHY_ENABLE_DOWNSHIFT BIT(4) ++ + #define MTK_PHY_PAGE_EXTENDED_52B5 0x52b5 + ++/* Registers on Token Ring debug nodes */ ++/* ch_addr = 0x0, node_addr = 0xf, data_addr = 0x2 */ ++#define AN_STATE_MASK GENMASK(22, 19) ++#define AN_STATE_SHIFT 19 ++#define AN_STATE_TX_DISABLE 1 ++ ++/* ch_addr = 0x0, node_addr = 0xf, data_addr = 0x3c */ ++#define AN_NEW_LP_CNT_LIMIT_MASK GENMASK(23, 20) ++#define AUTO_NP_10XEN BIT(6) ++ ++/* Registers on MDIO_MMD_VEND1 */ ++#define MTK_PHY_LINK_STATUS_MISC (0xa2) ++#define MTK_PHY_FINAL_SPEED_1000 BIT(3) ++ + /* Registers on MDIO_MMD_VEND2 */ + #define MTK_PHY_LED0_ON_CTRL 0x24 + #define MTK_PHY_LED1_ON_CTRL 0x26 +@@ -78,6 +98,7 @@ void __mtk_tr_clr_bits(struct phy_device + int mtk_phy_read_page(struct phy_device *phydev); + int mtk_phy_write_page(struct phy_device *phydev, int page); + ++int mtk_gphy_cl22_read_status(struct phy_device *phydev); + int mtk_phy_led_hw_is_supported(struct phy_device *phydev, u8 index, + unsigned long rules, + unsigned long supported_triggers); diff --git a/target/linux/mediatek/patches-6.6/733-11-net-phy-add-driver-for-built-in-2.5G-ethernet-PHY-on.patch b/target/linux/mediatek/patches-6.6/733-11-net-phy-add-driver-for-built-in-2.5G-ethernet-PHY-on.patch new file mode 100644 index 0000000000..a9595157ff --- /dev/null +++ b/target/linux/mediatek/patches-6.6/733-11-net-phy-add-driver-for-built-in-2.5G-ethernet-PHY-on.patch @@ -0,0 +1,477 @@ +From 69ca89165e39e6b6f4c79e6b4c03559e0fac7051 Mon Sep 17 00:00:00 2001 +From: "SkyLake.Huang" +Date: Mon, 1 Jul 2024 18:54:15 +0800 +Subject: [PATCH 11/13] net: phy: add driver for built-in 2.5G ethernet PHY on + MT7988 + +Add support for internal 2.5Gphy on MT7988. This driver will load +necessary firmware, add appropriate time delay and figure out LED. +Also, certain control registers will be set to fix link-up issues. + +Signed-off-by: SkyLake.Huang +--- + drivers/net/phy/mediatek/Kconfig | 11 + + drivers/net/phy/mediatek/Makefile | 1 + + drivers/net/phy/mediatek/mtk-2p5ge.c | 432 +++++++++++++++++++++++++++ + 4 files changed, 445 insertions(+) + create mode 100644 drivers/net/phy/mediatek/mtk-2p5ge.c + +--- a/drivers/net/phy/mediatek/Kconfig ++++ b/drivers/net/phy/mediatek/Kconfig +@@ -25,3 +25,14 @@ config MEDIATEK_GE_SOC_PHY + the MT7981 and MT7988 SoCs. These PHYs need calibration data + present in the SoCs efuse and will dynamically calibrate VCM + (common-mode voltage) during startup. ++ ++config MEDIATEK_2P5GE_PHY ++ tristate "MediaTek 2.5Gb Ethernet PHYs" ++ depends on (ARM64 && ARCH_MEDIATEK) || COMPILE_TEST ++ select MTK_NET_PHYLIB ++ help ++ Supports MediaTek SoC built-in 2.5Gb Ethernet PHYs. ++ ++ This will load necessary firmware and add appropriate time delay. ++ Accelerate this procedure through internal pbus instead of MDIO ++ bus. Certain link-up issues will also be fixed here. +--- a/drivers/net/phy/mediatek/Makefile ++++ b/drivers/net/phy/mediatek/Makefile +@@ -2,3 +2,4 @@ + obj-$(CONFIG_MTK_NET_PHYLIB) += mtk-phy-lib.o + obj-$(CONFIG_MEDIATEK_GE_PHY) += mtk-ge.o + obj-$(CONFIG_MEDIATEK_GE_SOC_PHY) += mtk-ge-soc.o ++obj-$(CONFIG_MEDIATEK_2P5GE_PHY) += mtk-2p5ge.o +--- /dev/null ++++ b/drivers/net/phy/mediatek/mtk-2p5ge.c +@@ -0,0 +1,432 @@ ++// SPDX-License-Identifier: GPL-2.0+ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include "mtk.h" ++ ++#define MTK_2P5GPHY_ID_MT7988 (0x00339c11) ++ ++#define MT7988_2P5GE_PMB_FW "mediatek/mt7988/i2p5ge-phy-pmb.bin" ++#define MT7988_2P5GE_PMB_FW_SIZE (0x20000) ++#define MT7988_2P5GE_PMB_FW_BASE (0x0f100000) ++#define MT7988_2P5GE_PMB_FW_LEN (0x20000) ++#define MT7988_2P5GE_MD32_EN_CFG_BASE (0x0f0f0018) ++#define MT7988_2P5GE_MD32_EN_CFG_LEN (0x20) ++#define MD32_EN BIT(0) ++ ++#define BASE100T_STATUS_EXTEND (0x10) ++#define BASE1000T_STATUS_EXTEND (0x11) ++#define EXTEND_CTRL_AND_STATUS (0x16) ++ ++#define PHY_AUX_CTRL_STATUS (0x1d) ++#define PHY_AUX_DPX_MASK GENMASK(5, 5) ++#define PHY_AUX_SPEED_MASK GENMASK(4, 2) ++ ++#define MTK_PHY_LPI_PCS_DSP_CTRL (0x121) ++#define MTK_PHY_LPI_SIG_EN_LO_THRESH100_MASK GENMASK(12, 8) ++ ++/* Registers on Token Ring debug nodes */ ++/* ch_addr = 0x0, node_addr = 0xf, data_addr = 0x3c */ ++#define AUTO_NP_10XEN BIT(6) ++ ++struct mtk_i2p5ge_phy_priv { ++ bool fw_loaded; ++ unsigned long led_state; ++}; ++ ++enum { ++ PHY_AUX_SPD_10 = 0, ++ PHY_AUX_SPD_100, ++ PHY_AUX_SPD_1000, ++ PHY_AUX_SPD_2500, ++}; ++ ++static int mt798x_2p5ge_phy_load_fw(struct phy_device *phydev) ++{ ++ struct mtk_i2p5ge_phy_priv *priv = phydev->priv; ++ void __iomem *md32_en_cfg_base, *pmb_addr; ++ struct device *dev = &phydev->mdio.dev; ++ const struct firmware *fw; ++ int ret, i; ++ u16 reg; ++ ++ if (priv->fw_loaded) ++ return 0; ++ ++ pmb_addr = ioremap(MT7988_2P5GE_PMB_FW_BASE, MT7988_2P5GE_PMB_FW_LEN); ++ if (!pmb_addr) ++ return -ENOMEM; ++ md32_en_cfg_base = ioremap(MT7988_2P5GE_MD32_EN_CFG_BASE, ++ MT7988_2P5GE_MD32_EN_CFG_LEN); ++ if (!md32_en_cfg_base) { ++ ret = -ENOMEM; ++ goto free_pmb; ++ } ++ ++ ret = request_firmware(&fw, MT7988_2P5GE_PMB_FW, dev); ++ if (ret) { ++ dev_err(dev, "failed to load firmware: %s, ret: %d\n", ++ MT7988_2P5GE_PMB_FW, ret); ++ goto free; ++ } ++ ++ if (fw->size != MT7988_2P5GE_PMB_FW_SIZE) { ++ dev_err(dev, "Firmware size 0x%zx != 0x%x\n", ++ fw->size, MT7988_2P5GE_PMB_FW_SIZE); ++ ret = -EINVAL; ++ goto release_fw; ++ } ++ ++ reg = readw(md32_en_cfg_base); ++ if (reg & MD32_EN) { ++ phy_set_bits(phydev, MII_BMCR, BMCR_RESET); ++ usleep_range(10000, 11000); ++ } ++ phy_set_bits(phydev, MII_BMCR, BMCR_PDOWN); ++ ++ /* Write magic number to safely stall MCU */ ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x800e, 0x1100); ++ phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x800f, 0x00df); ++ ++ for (i = 0; i < MT7988_2P5GE_PMB_FW_SIZE - 1; i += 4) ++ writel(*((uint32_t *)(fw->data + i)), pmb_addr + i); ++ dev_info(dev, "Firmware date code: %x/%x/%x, version: %x.%x\n", ++ be16_to_cpu(*((__be16 *)(fw->data + ++ MT7988_2P5GE_PMB_FW_SIZE - 8))), ++ *(fw->data + MT7988_2P5GE_PMB_FW_SIZE - 6), ++ *(fw->data + MT7988_2P5GE_PMB_FW_SIZE - 5), ++ *(fw->data + MT7988_2P5GE_PMB_FW_SIZE - 2), ++ *(fw->data + MT7988_2P5GE_PMB_FW_SIZE - 1)); ++ ++ writew(reg & ~MD32_EN, md32_en_cfg_base); ++ writew(reg | MD32_EN, md32_en_cfg_base); ++ phy_set_bits(phydev, MII_BMCR, BMCR_RESET); ++ /* We need a delay here to stabilize initialization of MCU */ ++ usleep_range(7000, 8000); ++ dev_info(dev, "Firmware loading/trigger ok.\n"); ++ ++ priv->fw_loaded = true; ++ ++release_fw: ++ release_firmware(fw); ++free: ++ iounmap(md32_en_cfg_base); ++free_pmb: ++ iounmap(pmb_addr); ++ ++ return ret; ++} ++ ++static int mt798x_2p5ge_phy_config_init(struct phy_device *phydev) ++{ ++ struct pinctrl *pinctrl; ++ int ret; ++ ++ /* Check if PHY interface type is compatible */ ++ if (phydev->interface != PHY_INTERFACE_MODE_INTERNAL) ++ return -ENODEV; ++ ++ ret = mt798x_2p5ge_phy_load_fw(phydev); ++ if (ret < 0) ++ return ret; ++ ++ /* Setup LED */ ++ phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED0_ON_CTRL, ++ MTK_PHY_LED_ON_POLARITY | MTK_PHY_LED_ON_LINK10 | ++ MTK_PHY_LED_ON_LINK100 | MTK_PHY_LED_ON_LINK1000 | ++ MTK_PHY_LED_ON_LINK2500); ++ phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED1_ON_CTRL, ++ MTK_PHY_LED_ON_FDX | MTK_PHY_LED_ON_HDX); ++ ++ /* Switch pinctrl after setting polarity to avoid bogus blinking */ ++ pinctrl = devm_pinctrl_get_select(&phydev->mdio.dev, "i2p5gbe-led"); ++ if (IS_ERR(pinctrl)) ++ dev_err(&phydev->mdio.dev, "Fail to set LED pins!\n"); ++ ++ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_LPI_PCS_DSP_CTRL, ++ MTK_PHY_LPI_SIG_EN_LO_THRESH100_MASK, 0); ++ ++ /* Enable 16-bit next page exchange bit if 1000-BT isn't advertising */ ++ mtk_tr_modify(phydev, 0x0, 0xf, 0x3c, AUTO_NP_10XEN, ++ FIELD_PREP(AUTO_NP_10XEN, 0x1)); ++ ++ /* Enable HW auto downshift */ ++ phy_modify_paged(phydev, MTK_PHY_PAGE_EXTENDED_1, ++ MTK_PHY_AUX_CTRL_AND_STATUS, ++ 0, MTK_PHY_ENABLE_DOWNSHIFT); ++ ++ return 0; ++} ++ ++static int mt798x_2p5ge_phy_config_aneg(struct phy_device *phydev) ++{ ++ bool changed = false; ++ u32 adv; ++ int ret; ++ ++ /* In fact, if we disable autoneg, we can't link up correctly: ++ * 2.5G/1G: Need AN to exchange master/slave information. ++ * 100M/10M: Without AN, link starts at half duplex (According to ++ * IEEE 802.3-2018), which this phy doesn't support. ++ */ ++ if (phydev->autoneg == AUTONEG_DISABLE) ++ return -EOPNOTSUPP; ++ ++ ret = genphy_c45_an_config_aneg(phydev); ++ if (ret < 0) ++ return ret; ++ if (ret > 0) ++ changed = true; ++ ++ /* Clause 45 doesn't define 1000BaseT support. Use Clause 22 instead in ++ * our design. ++ */ ++ adv = linkmode_adv_to_mii_ctrl1000_t(phydev->advertising); ++ ret = phy_modify_changed(phydev, MII_CTRL1000, ADVERTISE_1000FULL, adv); ++ if (ret < 0) ++ return ret; ++ if (ret > 0) ++ changed = true; ++ ++ return genphy_c45_check_and_restart_aneg(phydev, changed); ++} ++ ++static int mt798x_2p5ge_phy_get_features(struct phy_device *phydev) ++{ ++ int ret; ++ ++ ret = genphy_c45_pma_read_abilities(phydev); ++ if (ret) ++ return ret; ++ ++ /* This phy can't handle collision, and neither can (XFI)MAC it's ++ * connected to. Although it can do HDX handshake, it doesn't support ++ * CSMA/CD that HDX requires. ++ */ ++ linkmode_clear_bit(ETHTOOL_LINK_MODE_100baseT_Half_BIT, ++ phydev->supported); ++ ++ return 0; ++} ++ ++static int mt798x_2p5ge_phy_read_status(struct phy_device *phydev) ++{ ++ int ret; ++ ++ /* When MDIO_STAT1_LSTATUS is raised genphy_c45_read_link(), this phy ++ * actually hasn't finished AN. So use CL22's link update function ++ * instead. ++ */ ++ ret = genphy_update_link(phydev); ++ if (ret) ++ return ret; ++ ++ phydev->speed = SPEED_UNKNOWN; ++ phydev->duplex = DUPLEX_UNKNOWN; ++ phydev->pause = 0; ++ phydev->asym_pause = 0; ++ ++ /* We'll read link speed through vendor specific registers down below. ++ * So remove phy_resolve_aneg_linkmode (AN on) & genphy_c45_read_pma ++ * (AN off). ++ */ ++ if (phydev->autoneg == AUTONEG_ENABLE && phydev->autoneg_complete) { ++ ret = genphy_c45_read_lpa(phydev); ++ if (ret < 0) ++ return ret; ++ ++ /* Clause 45 doesn't define 1000BaseT support. Read the link ++ * partner's 1G advertisement via Clause 22. ++ */ ++ ret = phy_read(phydev, MII_STAT1000); ++ if (ret < 0) ++ return ret; ++ mii_stat1000_mod_linkmode_lpa_t(phydev->lp_advertising, ret); ++ } else if (phydev->autoneg == AUTONEG_DISABLE) { ++ linkmode_zero(phydev->lp_advertising); ++ } ++ ++ if (phydev->link) { ++ ret = phy_read(phydev, PHY_AUX_CTRL_STATUS); ++ if (ret < 0) ++ return ret; ++ ++ switch (FIELD_GET(PHY_AUX_SPEED_MASK, ret)) { ++ case PHY_AUX_SPD_10: ++ phydev->speed = SPEED_10; ++ break; ++ case PHY_AUX_SPD_100: ++ phydev->speed = SPEED_100; ++ break; ++ case PHY_AUX_SPD_1000: ++ phydev->speed = SPEED_1000; ++ break; ++ case PHY_AUX_SPD_2500: ++ phydev->speed = SPEED_2500; ++ break; ++ } ++ ++ phydev->duplex = DUPLEX_FULL; ++ /* FIXME: ++ * The current firmware always enables rate adaptation mode. ++ */ ++ phydev->rate_matching = RATE_MATCH_PAUSE; ++ } ++ ++ return 0; ++} ++ ++static int mt798x_2p5ge_phy_get_rate_matching(struct phy_device *phydev, ++ phy_interface_t iface) ++{ ++ return RATE_MATCH_PAUSE; ++} ++ ++static const unsigned long supported_triggers = ++ BIT(TRIGGER_NETDEV_FULL_DUPLEX) | ++ BIT(TRIGGER_NETDEV_LINK) | ++ BIT(TRIGGER_NETDEV_LINK_10) | ++ BIT(TRIGGER_NETDEV_LINK_100) | ++ BIT(TRIGGER_NETDEV_LINK_1000) | ++ BIT(TRIGGER_NETDEV_LINK_2500) | ++ BIT(TRIGGER_NETDEV_RX) | ++ BIT(TRIGGER_NETDEV_TX); ++ ++static int mt798x_2p5ge_phy_led_blink_set(struct phy_device *phydev, u8 index, ++ unsigned long *delay_on, ++ unsigned long *delay_off) ++{ ++ struct mtk_i2p5ge_phy_priv *priv = phydev->priv; ++ bool blinking = false; ++ int err = 0; ++ ++ err = mtk_phy_led_num_dly_cfg(index, delay_on, delay_off, &blinking); ++ if (err < 0) ++ return err; ++ ++ err = mtk_phy_hw_led_blink_set(phydev, index, &priv->led_state, ++ blinking); ++ if (err) ++ return err; ++ ++ return mtk_phy_hw_led_on_set(phydev, index, &priv->led_state, ++ MTK_2P5GPHY_LED_ON_MASK, false); ++} ++ ++static int mt798x_2p5ge_phy_led_brightness_set(struct phy_device *phydev, ++ u8 index, ++ enum led_brightness value) ++{ ++ struct mtk_i2p5ge_phy_priv *priv = phydev->priv; ++ int err; ++ ++ err = mtk_phy_hw_led_blink_set(phydev, index, &priv->led_state, false); ++ if (err) ++ return err; ++ ++ return mtk_phy_hw_led_on_set(phydev, index, &priv->led_state, ++ MTK_2P5GPHY_LED_ON_MASK, ++ (value != LED_OFF)); ++} ++ ++static int mt798x_2p5ge_phy_led_hw_is_supported(struct phy_device *phydev, ++ u8 index, unsigned long rules) ++{ ++ return mtk_phy_led_hw_is_supported(phydev, index, rules, ++ supported_triggers); ++} ++ ++static int mt798x_2p5ge_phy_led_hw_control_get(struct phy_device *phydev, ++ u8 index, unsigned long *rules) ++{ ++ struct mtk_i2p5ge_phy_priv *priv = phydev->priv; ++ ++ return mtk_phy_led_hw_ctrl_get(phydev, index, rules, &priv->led_state, ++ MTK_2P5GPHY_LED_ON_SET, ++ MTK_2P5GPHY_LED_RX_BLINK_SET, ++ MTK_2P5GPHY_LED_TX_BLINK_SET); ++}; ++ ++static int mt798x_2p5ge_phy_led_hw_control_set(struct phy_device *phydev, ++ u8 index, unsigned long rules) ++{ ++ struct mtk_i2p5ge_phy_priv *priv = phydev->priv; ++ ++ return mtk_phy_led_hw_ctrl_set(phydev, index, rules, &priv->led_state, ++ MTK_2P5GPHY_LED_ON_SET, ++ MTK_2P5GPHY_LED_RX_BLINK_SET, ++ MTK_2P5GPHY_LED_TX_BLINK_SET); ++}; ++ ++static int mt798x_2p5ge_phy_probe(struct phy_device *phydev) ++{ ++ struct mtk_i2p5ge_phy_priv *priv; ++ ++ priv = devm_kzalloc(&phydev->mdio.dev, ++ sizeof(struct mtk_i2p5ge_phy_priv), GFP_KERNEL); ++ if (!priv) ++ return -ENOMEM; ++ ++ switch (phydev->drv->phy_id) { ++ case MTK_2P5GPHY_ID_MT7988: ++ /* The original hardware only sets MDIO_DEVS_PMAPMD */ ++ phydev->c45_ids.mmds_present |= MDIO_DEVS_PCS | ++ MDIO_DEVS_AN | ++ MDIO_DEVS_VEND1 | ++ MDIO_DEVS_VEND2; ++ break; ++ default: ++ return -EINVAL; ++ } ++ ++ priv->fw_loaded = false; ++ phydev->priv = priv; ++ ++ mtk_phy_leds_state_init(phydev); ++ ++ return 0; ++} ++ ++static struct phy_driver mtk_2p5gephy_driver[] = { ++ { ++ PHY_ID_MATCH_MODEL(MTK_2P5GPHY_ID_MT7988), ++ .name = "MediaTek MT7988 2.5GbE PHY", ++ .probe = mt798x_2p5ge_phy_probe, ++ .config_init = mt798x_2p5ge_phy_config_init, ++ .config_aneg = mt798x_2p5ge_phy_config_aneg, ++ .get_features = mt798x_2p5ge_phy_get_features, ++ .read_status = mt798x_2p5ge_phy_read_status, ++ .get_rate_matching = mt798x_2p5ge_phy_get_rate_matching, ++ .suspend = genphy_suspend, ++ .resume = genphy_resume, ++ .read_page = mtk_phy_read_page, ++ .write_page = mtk_phy_write_page, ++ .led_blink_set = mt798x_2p5ge_phy_led_blink_set, ++ .led_brightness_set = mt798x_2p5ge_phy_led_brightness_set, ++ .led_hw_is_supported = mt798x_2p5ge_phy_led_hw_is_supported, ++ .led_hw_control_get = mt798x_2p5ge_phy_led_hw_control_get, ++ .led_hw_control_set = mt798x_2p5ge_phy_led_hw_control_set, ++ }, ++}; ++ ++module_phy_driver(mtk_2p5gephy_driver); ++ ++static struct mdio_device_id __maybe_unused mtk_2p5ge_phy_tbl[] = { ++ { PHY_ID_MATCH_VENDOR(0x00339c00) }, ++ { } ++}; ++ ++MODULE_DESCRIPTION("MediaTek 2.5Gb Ethernet PHY driver"); ++MODULE_AUTHOR("SkyLake Huang "); ++MODULE_LICENSE("GPL"); ++ ++MODULE_DEVICE_TABLE(mdio, mtk_2p5ge_phy_tbl); ++MODULE_FIRMWARE(MT7988_2P5GE_PMB_FW); diff --git a/target/linux/mediatek/patches-6.6/733-12-net-phy-mediatek-Fix-alignment-in-callback-functions.patch b/target/linux/mediatek/patches-6.6/733-12-net-phy-mediatek-Fix-alignment-in-callback-functions.patch new file mode 100644 index 0000000000..8657886138 --- /dev/null +++ b/target/linux/mediatek/patches-6.6/733-12-net-phy-mediatek-Fix-alignment-in-callback-functions.patch @@ -0,0 +1,130 @@ +From 07e90eb1819319a0c34b0cf3a57a4a3878e96e4d Mon Sep 17 00:00:00 2001 +From: "SkyLake.Huang" +Date: Mon, 1 Jul 2024 18:54:16 +0800 +Subject: [PATCH 12/13] net: phy: mediatek: Fix alignment in callback + functions' hook + +Align declarations in mtk_gephy_driver(mtk-ge.c) and +mtk_socphy_driver(mtk-ge-soc.c). At first, some of them are +".foo= method_foo", and others are ".bar= method_bar". +Use space instead for all of them here in case line is longer than +80 chars. + +Signed-off-by: SkyLake.Huang +--- + drivers/net/phy/mediatek/mtk-ge-soc.c | 40 +++++++++++++-------------- + drivers/net/phy/mediatek/mtk-ge.c | 34 +++++++++++------------ + 2 files changed, 37 insertions(+), 37 deletions(-) + +--- a/drivers/net/phy/mediatek/mtk-ge-soc.c ++++ b/drivers/net/phy/mediatek/mtk-ge-soc.c +@@ -1394,17 +1394,17 @@ static int mt7981_phy_probe(struct phy_d + static struct phy_driver mtk_socphy_driver[] = { + { + PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7981), +- .name = "MediaTek MT7981 PHY", +- .config_init = mt798x_phy_config_init, +- .read_status = mtk_gphy_cl22_read_status, +- .config_intr = genphy_no_config_intr, ++ .name = "MediaTek MT7981 PHY", ++ .config_init = mt798x_phy_config_init, ++ .read_status = mtk_gphy_cl22_read_status, ++ .config_intr = genphy_no_config_intr, + .handle_interrupt = genphy_handle_interrupt_no_ack, +- .probe = mt7981_phy_probe, +- .suspend = genphy_suspend, +- .resume = genphy_resume, +- .read_page = mtk_phy_read_page, +- .write_page = mtk_phy_write_page, +- .led_blink_set = mt798x_phy_led_blink_set, ++ .probe = mt7981_phy_probe, ++ .suspend = genphy_suspend, ++ .resume = genphy_resume, ++ .read_page = mtk_phy_read_page, ++ .write_page = mtk_phy_write_page, ++ .led_blink_set = mt798x_phy_led_blink_set, + .led_brightness_set = mt798x_phy_led_brightness_set, + .led_hw_is_supported = mt798x_phy_led_hw_is_supported, + .led_hw_control_set = mt798x_phy_led_hw_control_set, +@@ -1412,17 +1412,17 @@ static struct phy_driver mtk_socphy_driv + }, + { + PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7988), +- .name = "MediaTek MT7988 PHY", +- .config_init = mt798x_phy_config_init, +- .read_status = mtk_gphy_cl22_read_status, +- .config_intr = genphy_no_config_intr, ++ .name = "MediaTek MT7988 PHY", ++ .config_init = mt798x_phy_config_init, ++ .read_status = mtk_gphy_cl22_read_status, ++ .config_intr = genphy_no_config_intr, + .handle_interrupt = genphy_handle_interrupt_no_ack, +- .probe = mt7988_phy_probe, +- .suspend = genphy_suspend, +- .resume = genphy_resume, +- .read_page = mtk_phy_read_page, +- .write_page = mtk_phy_write_page, +- .led_blink_set = mt798x_phy_led_blink_set, ++ .probe = mt7988_phy_probe, ++ .suspend = genphy_suspend, ++ .resume = genphy_resume, ++ .read_page = mtk_phy_read_page, ++ .write_page = mtk_phy_write_page, ++ .led_blink_set = mt798x_phy_led_blink_set, + .led_brightness_set = mt798x_phy_led_brightness_set, + .led_hw_is_supported = mt798x_phy_led_hw_is_supported, + .led_hw_control_set = mt798x_phy_led_hw_control_set, +--- a/drivers/net/phy/mediatek/mtk-ge.c ++++ b/drivers/net/phy/mediatek/mtk-ge.c +@@ -230,34 +230,34 @@ static int mt753x_phy_led_hw_control_set + static struct phy_driver mtk_gephy_driver[] = { + { + PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7530), +- .name = "MediaTek MT7530 PHY", +- .config_init = mt7530_phy_config_init, ++ .name = "MediaTek MT7530 PHY", ++ .config_init = mt7530_phy_config_init, + /* Interrupts are handled by the switch, not the PHY + * itself. + */ +- .config_intr = genphy_no_config_intr, ++ .config_intr = genphy_no_config_intr, + .handle_interrupt = genphy_handle_interrupt_no_ack, +- .suspend = genphy_suspend, +- .resume = genphy_resume, +- .read_page = mtk_phy_read_page, +- .write_page = mtk_phy_write_page, ++ .suspend = genphy_suspend, ++ .resume = genphy_resume, ++ .read_page = mtk_phy_read_page, ++ .write_page = mtk_phy_write_page, + }, + { + PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7531), +- .name = "MediaTek MT7531 PHY", +- .probe = mt7531_phy_probe, +- .config_init = mt7531_phy_config_init, +- .read_status = mtk_gphy_cl22_read_status, ++ .name = "MediaTek MT7531 PHY", ++ .probe = mt7531_phy_probe, ++ .config_init = mt7531_phy_config_init, ++ .read_status = mtk_gphy_cl22_read_status, + /* Interrupts are handled by the switch, not the PHY + * itself. + */ +- .config_intr = genphy_no_config_intr, ++ .config_intr = genphy_no_config_intr, + .handle_interrupt = genphy_handle_interrupt_no_ack, +- .suspend = genphy_suspend, +- .resume = genphy_resume, +- .read_page = mtk_phy_read_page, +- .write_page = mtk_phy_write_page, +- .led_blink_set = mt753x_phy_led_blink_set, ++ .suspend = genphy_suspend, ++ .resume = genphy_resume, ++ .read_page = mtk_phy_read_page, ++ .write_page = mtk_phy_write_page, ++ .led_blink_set = mt753x_phy_led_blink_set, + .led_brightness_set = mt753x_phy_led_brightness_set, + .led_hw_is_supported = mt753x_phy_led_hw_is_supported, + .led_hw_control_set = mt753x_phy_led_hw_control_set, diff --git a/target/linux/mediatek/patches-6.6/733-13-net-phy-mediatek-Remove-unnecessary-outer-parens-of-.patch b/target/linux/mediatek/patches-6.6/733-13-net-phy-mediatek-Remove-unnecessary-outer-parens-of-.patch new file mode 100644 index 0000000000..dd99bbba9a --- /dev/null +++ b/target/linux/mediatek/patches-6.6/733-13-net-phy-mediatek-Remove-unnecessary-outer-parens-of-.patch @@ -0,0 +1,65 @@ +From e59883b637ae317c2ac275b542e8a50670d76e7c Mon Sep 17 00:00:00 2001 +From: "SkyLake.Huang" +Date: Mon, 1 Jul 2024 18:54:17 +0800 +Subject: [PATCH 13/13] net: phy: mediatek: Remove unnecessary outer parens of + "supported_triggers" var + +This patch removes unnecessary outer parens of "supported_triggers" vars +in mtk-ge.c & mtk-ge-soc.c to improve readability. + +Signed-off-by: SkyLake.Huang +--- + drivers/net/phy/mediatek/mtk-ge-soc.c | 16 ++++++++-------- + drivers/net/phy/mediatek/mtk-ge.c | 16 ++++++++-------- + 2 files changed, 16 insertions(+), 16 deletions(-) + +--- a/drivers/net/phy/mediatek/mtk-ge-soc.c ++++ b/drivers/net/phy/mediatek/mtk-ge-soc.c +@@ -1224,14 +1224,14 @@ static int mt798x_phy_led_brightness_set + } + + static const unsigned long supported_triggers = +- (BIT(TRIGGER_NETDEV_FULL_DUPLEX) | +- BIT(TRIGGER_NETDEV_HALF_DUPLEX) | +- BIT(TRIGGER_NETDEV_LINK) | +- BIT(TRIGGER_NETDEV_LINK_10) | +- BIT(TRIGGER_NETDEV_LINK_100) | +- BIT(TRIGGER_NETDEV_LINK_1000) | +- BIT(TRIGGER_NETDEV_RX) | +- BIT(TRIGGER_NETDEV_TX)); ++ BIT(TRIGGER_NETDEV_FULL_DUPLEX) | ++ BIT(TRIGGER_NETDEV_HALF_DUPLEX) | ++ BIT(TRIGGER_NETDEV_LINK) | ++ BIT(TRIGGER_NETDEV_LINK_10) | ++ BIT(TRIGGER_NETDEV_LINK_100) | ++ BIT(TRIGGER_NETDEV_LINK_1000) | ++ BIT(TRIGGER_NETDEV_RX) | ++ BIT(TRIGGER_NETDEV_TX); + + static int mt798x_phy_led_hw_is_supported(struct phy_device *phydev, u8 index, + unsigned long rules) +--- a/drivers/net/phy/mediatek/mtk-ge.c ++++ b/drivers/net/phy/mediatek/mtk-ge.c +@@ -189,14 +189,14 @@ static int mt753x_phy_led_brightness_set + } + + static const unsigned long supported_triggers = +- (BIT(TRIGGER_NETDEV_FULL_DUPLEX) | +- BIT(TRIGGER_NETDEV_HALF_DUPLEX) | +- BIT(TRIGGER_NETDEV_LINK) | +- BIT(TRIGGER_NETDEV_LINK_10) | +- BIT(TRIGGER_NETDEV_LINK_100) | +- BIT(TRIGGER_NETDEV_LINK_1000) | +- BIT(TRIGGER_NETDEV_RX) | +- BIT(TRIGGER_NETDEV_TX)); ++ BIT(TRIGGER_NETDEV_FULL_DUPLEX) | ++ BIT(TRIGGER_NETDEV_HALF_DUPLEX) | ++ BIT(TRIGGER_NETDEV_LINK) | ++ BIT(TRIGGER_NETDEV_LINK_10) | ++ BIT(TRIGGER_NETDEV_LINK_100) | ++ BIT(TRIGGER_NETDEV_LINK_1000) | ++ BIT(TRIGGER_NETDEV_RX) | ++ BIT(TRIGGER_NETDEV_TX); + + static int mt753x_phy_led_hw_is_supported(struct phy_device *phydev, u8 index, + unsigned long rules) diff --git a/target/linux/mediatek/patches-6.6/733-net-phy-add-driver-for-MediaTek-2.5G-PHY.patch b/target/linux/mediatek/patches-6.6/733-net-phy-add-driver-for-MediaTek-2.5G-PHY.patch deleted file mode 100644 index 74b16be152..0000000000 --- a/target/linux/mediatek/patches-6.6/733-net-phy-add-driver-for-MediaTek-2.5G-PHY.patch +++ /dev/null @@ -1,39 +0,0 @@ -From 128dc09b0af36772062142ce9e85b19c84ac789a Mon Sep 17 00:00:00 2001 -From: Daniel Golle -Date: Tue, 28 Feb 2023 17:53:37 +0000 -Subject: [PATCH] net: phy: add driver for MediaTek 2.5G PHY - -Signed-off-by: Daniel Golle ---- - drivers/net/phy/Kconfig | 7 ++ - drivers/net/phy/Makefile | 1 + - drivers/net/phy/mediatek-2p5ge.c | 220 +++++++++++++++++++++++++++++++ - 3 files changed, 226 insertions(+) - create mode 100644 drivers/net/phy/mediatek-2p5ge.c - ---- a/drivers/net/phy/Kconfig -+++ b/drivers/net/phy/Kconfig -@@ -330,6 +330,13 @@ config MEDIATEK_GE_SOC_PHY - present in the SoCs efuse and will dynamically calibrate VCM - (common-mode voltage) during startup. - -+config MEDIATEK_2P5G_PHY -+ tristate "MediaTek 2.5G Ethernet PHY" -+ depends on (ARCH_MEDIATEK && ARM64) || COMPILE_TEST -+ default NET_MEDIATEK_SOC -+ help -+ Supports the MediaTek 2.5G Ethernet PHY. -+ - config MICREL_PHY - tristate "Micrel PHYs" - depends on PTP_1588_CLOCK_OPTIONAL ---- a/drivers/net/phy/Makefile -+++ b/drivers/net/phy/Makefile -@@ -82,6 +82,7 @@ obj-$(CONFIG_MARVELL_PHY) += marvell.o - obj-$(CONFIG_MARVELL_88Q2XXX_PHY) += marvell-88q2xxx.o - obj-$(CONFIG_MARVELL_88X2222_PHY) += marvell-88x2222.o - obj-$(CONFIG_MAXLINEAR_GPHY) += mxl-gpy.o -+obj-$(CONFIG_MEDIATEK_2P5G_PHY) += mediatek-2p5ge.o - obj-$(CONFIG_MEDIATEK_GE_PHY) += mediatek-ge.o - obj-$(CONFIG_MEDIATEK_GE_SOC_PHY) += mediatek-ge-soc.o - obj-$(CONFIG_MESON_GXL_PHY) += meson-gxl.o