From: Robert Hancock Date: Thu, 6 Jun 2019 22:28:09 +0000 (-0600) Subject: net: axienet: Use clock framework to get device clock rate X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=09a0354cadec267be7f5249c89eb998b3474263a;p=openwrt%2Fstaging%2Fblogic.git net: axienet: Use clock framework to get device clock rate This driver was previously always calculating the MDIO clock divisor (from AXI bus clock to MDIO bus clock) based on the CPU clock frequency, assuming that it is the same as the AXI bus frequency, but that simplistic method only works on the MicroBlaze platform. Add support for specifying the clock used for the device in the device tree using the clock framework. If the clock is specified then it will be used when calculating the clock divisor. The previous CPU clock detection method is left for backward compatibility if no clock is specified. Signed-off-by: Robert Hancock Signed-off-by: David S. Miller --- diff --git a/Documentation/devicetree/bindings/net/xilinx_axienet.txt b/Documentation/devicetree/bindings/net/xilinx_axienet.txt index 38f9ec076743..2dea90332ebb 100644 --- a/Documentation/devicetree/bindings/net/xilinx_axienet.txt +++ b/Documentation/devicetree/bindings/net/xilinx_axienet.txt @@ -31,6 +31,11 @@ Optional properties: 1 to enable partial TX checksum offload, 2 to enable full TX checksum offload - xlnx,rxcsum : Same values as xlnx,txcsum but for RX checksum offload +- clocks : AXI bus clock for the device. Refer to common clock bindings. + Used to calculate MDIO clock divisor. If not specified, it is + auto-detected from the CPU clock (but only on platforms where + this is possible). New device trees should specify this - the + auto detection is only for backward compatibility. Example: axi_ethernet_eth: ethernet@40c00000 { @@ -38,6 +43,7 @@ Example: device_type = "network"; interrupt-parent = <µblaze_0_axi_intc>; interrupts = <2 0>; + clocks = <&axi_clk>; phy-mode = "mii"; reg = <0x40c00000 0x40000>; xlnx,rxcsum = <0x2>; diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet.h b/drivers/net/ethernet/xilinx/xilinx_axienet.h index f9078bd7f86f..f240ff1b7296 100644 --- a/drivers/net/ethernet/xilinx/xilinx_axienet.h +++ b/drivers/net/ethernet/xilinx/xilinx_axienet.h @@ -418,6 +418,9 @@ struct axienet_local { /* Connection to PHY device */ struct device_node *phy_node; + /* Clock for AXI bus */ + struct clk *clk; + /* MDIO bus data */ struct mii_bus *mii_bus; /* MII bus reference */ @@ -502,7 +505,7 @@ static inline void axienet_iow(struct axienet_local *lp, off_t offset, } /* Function prototypes visible in xilinx_axienet_mdio.c for other files */ -int axienet_mdio_setup(struct axienet_local *lp, struct device_node *np); +int axienet_mdio_setup(struct axienet_local *lp); int axienet_mdio_wait_until_ready(struct axienet_local *lp); void axienet_mdio_teardown(struct axienet_local *lp); diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c index ffbd4d762534..42b343cb3e2b 100644 --- a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c +++ b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c @@ -21,6 +21,7 @@ * - Add support for extended VLAN support. */ +#include #include #include #include @@ -1611,9 +1612,24 @@ static int axienet_probe(struct platform_device *pdev) lp->phy_node = of_parse_phandle(pdev->dev.of_node, "phy-handle", 0); if (lp->phy_node) { - ret = axienet_mdio_setup(lp, pdev->dev.of_node); + lp->clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(lp->clk)) { + dev_warn(&pdev->dev, "Failed to get clock: %ld\n", + PTR_ERR(lp->clk)); + lp->clk = NULL; + } else { + ret = clk_prepare_enable(lp->clk); + if (ret) { + dev_err(&pdev->dev, "Unable to enable clock: %d\n", + ret); + goto free_netdev; + } + } + + ret = axienet_mdio_setup(lp); if (ret) - dev_warn(&pdev->dev, "error registering MDIO bus\n"); + dev_warn(&pdev->dev, + "error registering MDIO bus: %d\n", ret); } ret = register_netdev(lp->ndev); @@ -1638,6 +1654,9 @@ static int axienet_remove(struct platform_device *pdev) axienet_mdio_teardown(lp); unregister_netdev(ndev); + if (lp->clk) + clk_disable_unprepare(lp->clk); + of_node_put(lp->phy_node); lp->phy_node = NULL; diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet_mdio.c b/drivers/net/ethernet/xilinx/xilinx_axienet_mdio.c index 665ae1d16f1e..cce0dc42583e 100644 --- a/drivers/net/ethernet/xilinx/xilinx_axienet_mdio.c +++ b/drivers/net/ethernet/xilinx/xilinx_axienet_mdio.c @@ -8,6 +8,7 @@ * Copyright (c) 2010 - 2012 Xilinx, Inc. All rights reserved. */ +#include #include #include #include @@ -16,7 +17,7 @@ #include "xilinx_axienet.h" #define MAX_MDIO_FREQ 2500000 /* 2.5 MHz */ -#define DEFAULT_CLOCK_DIVISOR XAE_MDIO_DIV_DFT +#define DEFAULT_HOST_CLOCK 150000000 /* 150 MHz */ /* Wait till MDIO interface is ready to accept a new transaction.*/ int axienet_mdio_wait_until_ready(struct axienet_local *lp) @@ -114,7 +115,6 @@ static int axienet_mdio_write(struct mii_bus *bus, int phy_id, int reg, /** * axienet_mdio_setup - MDIO setup function * @lp: Pointer to axienet local data structure. - * @np: Pointer to device node * * Return: 0 on success, -ETIMEDOUT on a timeout, -ENOMEM when * mdiobus_alloc (to allocate memory for mii bus structure) fails. @@ -122,13 +122,37 @@ static int axienet_mdio_write(struct mii_bus *bus, int phy_id, int reg, * Sets up the MDIO interface by initializing the MDIO clock and enabling the * MDIO interface in hardware. Register the MDIO interface. **/ -int axienet_mdio_setup(struct axienet_local *lp, struct device_node *np) +int axienet_mdio_setup(struct axienet_local *lp) { int ret; u32 clk_div, host_clock; struct mii_bus *bus; struct device_node *mdio_node; - struct device_node *np1; + + if (lp->clk) { + host_clock = clk_get_rate(lp->clk); + } else { + struct device_node *np1; + + /* Legacy fallback: detect CPU clock frequency and use as AXI + * bus clock frequency. This only works on certain platforms. + */ + np1 = of_find_node_by_name(NULL, "cpu"); + if (!np1) { + netdev_warn(lp->ndev, "Could not find CPU device node.\n"); + host_clock = DEFAULT_HOST_CLOCK; + } else { + ret = of_property_read_u32(np1, "clock-frequency", + &host_clock); + if (ret) { + netdev_warn(lp->ndev, "CPU clock-frequency property not found.\n"); + host_clock = DEFAULT_HOST_CLOCK; + } + of_node_put(np1); + } + netdev_info(lp->ndev, "Setting assumed host clock to %u\n", + host_clock); + } /* clk_div can be calculated by deriving it from the equation: * fMDIO = fHOST / ((1 + clk_div) * 2) @@ -155,25 +179,6 @@ int axienet_mdio_setup(struct axienet_local *lp, struct device_node *np) * "clock-frequency" from the CPU */ - np1 = of_find_node_by_name(NULL, "cpu"); - if (!np1) { - netdev_warn(lp->ndev, "Could not find CPU device node.\n"); - netdev_warn(lp->ndev, - "Setting MDIO clock divisor to default %d\n", - DEFAULT_CLOCK_DIVISOR); - clk_div = DEFAULT_CLOCK_DIVISOR; - goto issue; - } - if (of_property_read_u32(np1, "clock-frequency", &host_clock)) { - netdev_warn(lp->ndev, "clock-frequency property not found.\n"); - netdev_warn(lp->ndev, - "Setting MDIO clock divisor to default %d\n", - DEFAULT_CLOCK_DIVISOR); - clk_div = DEFAULT_CLOCK_DIVISOR; - of_node_put(np1); - goto issue; - } - clk_div = (host_clock / (MAX_MDIO_FREQ * 2)) - 1; /* If there is any remainder from the division of * fHOST / (MAX_MDIO_FREQ * 2), then we need to add @@ -186,8 +191,6 @@ int axienet_mdio_setup(struct axienet_local *lp, struct device_node *np) "Setting MDIO clock divisor to %u/%u Hz host clock.\n", clk_div, host_clock); - of_node_put(np1); -issue: axienet_iow(lp, XAE_MDIO_MC_OFFSET, (((u32) clk_div) | XAE_MDIO_MC_MDIOEN_MASK));