From: Robert Marko Date: Thu, 11 Apr 2024 15:26:47 +0000 (+0200) Subject: qualcommax: drop 6.1 support X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=076f945dfbc8afa6ced7c5f67d95ab27383dd1e4;p=openwrt%2Fopenwrt.git qualcommax: drop 6.1 support We have defaulted to 6.6 for a while so its time to completely drop 6.1 so new devices dont have to include patches for 6.1. Signed-off-by: Robert Marko --- diff --git a/target/linux/qualcommax/config-6.1 b/target/linux/qualcommax/config-6.1 deleted file mode 100644 index 55f6a2ba4f..0000000000 --- a/target/linux/qualcommax/config-6.1 +++ /dev/null @@ -1,541 +0,0 @@ -CONFIG_64BIT=y -# CONFIG_APQ_GCC_8084 is not set -# CONFIG_APQ_MMCC_8084 is not set -CONFIG_ARCH_BINFMT_ELF_EXTRA_PHDRS=y -CONFIG_ARCH_CORRECT_STACKTRACE_ON_KRETPROBE=y -CONFIG_ARCH_DMA_ADDR_T_64BIT=y -CONFIG_ARCH_HIBERNATION_POSSIBLE=y -CONFIG_ARCH_KEEP_MEMBLOCK=y -CONFIG_ARCH_MHP_MEMMAP_ON_MEMORY_ENABLE=y -CONFIG_ARCH_MMAP_RND_BITS=18 -CONFIG_ARCH_MMAP_RND_BITS_MAX=24 -CONFIG_ARCH_MMAP_RND_BITS_MIN=18 -CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MIN=11 -CONFIG_ARCH_NR_GPIO=0 -CONFIG_ARCH_PROC_KCORE_TEXT=y -CONFIG_ARCH_QCOM=y -CONFIG_ARCH_SPARSEMEM_ENABLE=y -CONFIG_ARCH_STACKWALK=y -CONFIG_ARCH_SUSPEND_POSSIBLE=y -CONFIG_ARCH_WANTS_NO_INSTR=y -CONFIG_ARCH_WANTS_THP_SWAP=y -CONFIG_ARM64=y -CONFIG_ARM64_4K_PAGES=y -CONFIG_ARM64_ERRATUM_1165522=y -CONFIG_ARM64_ERRATUM_1286807=y -CONFIG_ARM64_ERRATUM_2051678=y -CONFIG_ARM64_ERRATUM_2054223=y -CONFIG_ARM64_ERRATUM_2067961=y -CONFIG_ARM64_ERRATUM_2077057=y -CONFIG_ARM64_ERRATUM_2658417=y -CONFIG_ARM64_LD_HAS_FIX_ERRATUM_843419=y -CONFIG_ARM64_PAGE_SHIFT=12 -CONFIG_ARM64_PA_BITS=48 -CONFIG_ARM64_PA_BITS_48=y -CONFIG_ARM64_PTR_AUTH=y -CONFIG_ARM64_PTR_AUTH_KERNEL=y -CONFIG_ARM64_SME=y -CONFIG_ARM64_SVE=y -CONFIG_ARM64_TAGGED_ADDR_ABI=y -CONFIG_ARM64_VA_BITS=39 -CONFIG_ARM64_VA_BITS_39=y -CONFIG_ARM64_WORKAROUND_REPEAT_TLBI=y -CONFIG_ARM64_WORKAROUND_SPECULATIVE_AT=y -CONFIG_ARM64_WORKAROUND_TSB_FLUSH_FAILURE=y -CONFIG_ARM_AMBA=y -CONFIG_ARM_ARCH_TIMER=y -CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y -CONFIG_ARM_GIC=y -CONFIG_ARM_GIC_V2M=y -CONFIG_ARM_GIC_V3=y -CONFIG_ARM_GIC_V3_ITS=y -CONFIG_ARM_GIC_V3_ITS_PCI=y -# CONFIG_ARM_MHU_V2 is not set -CONFIG_ARM_PSCI_CPUIDLE=y -CONFIG_ARM_PSCI_FW=y -# CONFIG_ARM_QCOM_CPUFREQ_HW is not set -CONFIG_ARM_QCOM_CPUFREQ_NVMEM=y -CONFIG_AT803X_PHY=y -CONFIG_AUDIT_ARCH_COMPAT_GENERIC=y -CONFIG_BLK_DEV_LOOP=y -CONFIG_BLK_DEV_SD=y -CONFIG_BLK_MQ_PCI=y -CONFIG_BLK_MQ_VIRTIO=y -CONFIG_BLK_PM=y -CONFIG_CAVIUM_TX2_ERRATUM_219=y -CONFIG_CC_HAVE_SHADOW_CALL_STACK=y -CONFIG_CC_HAVE_STACKPROTECTOR_SYSREG=y -CONFIG_CC_IMPLICIT_FALLTHROUGH="-Wimplicit-fallthrough=5" -CONFIG_CC_NO_ARRAY_BOUNDS=y -CONFIG_CLONE_BACKWARDS=y -CONFIG_COMMON_CLK=y -CONFIG_COMMON_CLK_QCOM=y -CONFIG_COMPACT_UNEVICTABLE_DEFAULT=1 -# CONFIG_COMPAT_32BIT_TIME is not set -CONFIG_CONTEXT_TRACKING=y -CONFIG_CONTEXT_TRACKING_IDLE=y -CONFIG_COREDUMP=y -CONFIG_CPUFREQ_DT=y -CONFIG_CPUFREQ_DT_PLATDEV=y -CONFIG_CPU_FREQ=y -# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set -CONFIG_CPU_FREQ_DEFAULT_GOV_SCHEDUTIL=y -CONFIG_CPU_FREQ_GOV_ATTR_SET=y -# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set -# CONFIG_CPU_FREQ_GOV_ONDEMAND is not set -CONFIG_CPU_FREQ_GOV_PERFORMANCE=y -# CONFIG_CPU_FREQ_GOV_POWERSAVE is not set -CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y -# CONFIG_CPU_FREQ_GOV_USERSPACE is not set -CONFIG_CPU_FREQ_STAT=y -CONFIG_CPU_FREQ_THERMAL=y -CONFIG_CPU_IDLE=y -CONFIG_CPU_IDLE_GOV_MENU=y -CONFIG_CPU_IDLE_MULTIPLE_DRIVERS=y -CONFIG_CPU_LITTLE_ENDIAN=y -CONFIG_CPU_PM=y -CONFIG_CPU_RMAP=y -CONFIG_CPU_THERMAL=y -CONFIG_CRC16=y -CONFIG_CRC8=y -CONFIG_CRYPTO_AUTHENC=y -CONFIG_CRYPTO_CBC=y -CONFIG_CRYPTO_DEFLATE=y -CONFIG_CRYPTO_DEV_QCE=y -CONFIG_CRYPTO_DEV_QCE_AEAD=y -# CONFIG_CRYPTO_DEV_QCE_ENABLE_AEAD is not set -CONFIG_CRYPTO_DEV_QCE_ENABLE_ALL=y -# CONFIG_CRYPTO_DEV_QCE_ENABLE_SHA is not set -# CONFIG_CRYPTO_DEV_QCE_ENABLE_SKCIPHER is not set -CONFIG_CRYPTO_DEV_QCE_SHA=y -CONFIG_CRYPTO_DEV_QCE_SKCIPHER=y -CONFIG_CRYPTO_DEV_QCE_SW_MAX_LEN=512 -CONFIG_CRYPTO_DEV_QCOM_RNG=y -CONFIG_CRYPTO_ECB=y -CONFIG_CRYPTO_HASH_INFO=y -CONFIG_CRYPTO_HW=y -CONFIG_CRYPTO_LIB_BLAKE2S_GENERIC=y -CONFIG_CRYPTO_LIB_DES=y -CONFIG_CRYPTO_LIB_SHA1=y -CONFIG_CRYPTO_LIB_SHA256=y -CONFIG_CRYPTO_LIB_UTILS=y -CONFIG_CRYPTO_LZO=y -CONFIG_CRYPTO_RNG=y -CONFIG_CRYPTO_RNG2=y -CONFIG_CRYPTO_SHA1=y -CONFIG_CRYPTO_SHA256=y -CONFIG_CRYPTO_XTS=y -CONFIG_CRYPTO_ZSTD=y -CONFIG_DCACHE_WORD_ACCESS=y -CONFIG_DEBUG_BUGVERBOSE=y -CONFIG_DEBUG_INFO=y -CONFIG_DEV_COREDUMP=y -CONFIG_DMADEVICES=y -CONFIG_DMA_DIRECT_REMAP=y -CONFIG_DMA_ENGINE=y -CONFIG_DMA_OF=y -CONFIG_DMA_VIRTUAL_CHANNELS=y -CONFIG_DTC=y -CONFIG_DT_IDLE_STATES=y -CONFIG_EDAC_SUPPORT=y -CONFIG_EXCLUSIVE_SYSTEM_RAM=y -CONFIG_FIXED_PHY=y -CONFIG_FIX_EARLYCON_MEM=y -CONFIG_FRAME_POINTER=y -CONFIG_FUJITSU_ERRATUM_010001=y -CONFIG_FWNODE_MDIO=y -CONFIG_FW_LOADER_PAGED_BUF=y -CONFIG_FW_LOADER_SYSFS=y -CONFIG_GCC11_NO_ARRAY_BOUNDS=y -CONFIG_GCC_ASM_GOTO_OUTPUT_WORKAROUND=y -CONFIG_GCC_SUPPORTS_DYNAMIC_FTRACE_WITH_REGS=y -CONFIG_GENERIC_ALLOCATOR=y -CONFIG_GENERIC_ARCH_TOPOLOGY=y -CONFIG_GENERIC_BUG=y -CONFIG_GENERIC_BUG_RELATIVE_POINTERS=y -CONFIG_GENERIC_CLOCKEVENTS=y -CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y -CONFIG_GENERIC_CPU_AUTOPROBE=y -CONFIG_GENERIC_CPU_VULNERABILITIES=y -CONFIG_GENERIC_CSUM=y -CONFIG_GENERIC_EARLY_IOREMAP=y -CONFIG_GENERIC_GETTIMEOFDAY=y -CONFIG_GENERIC_IDLE_POLL_SETUP=y -CONFIG_GENERIC_IOREMAP=y -CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y -CONFIG_GENERIC_IRQ_SHOW=y -CONFIG_GENERIC_IRQ_SHOW_LEVEL=y -CONFIG_GENERIC_LIB_DEVMEM_IS_ALLOWED=y -CONFIG_GENERIC_MSI_IRQ=y -CONFIG_GENERIC_MSI_IRQ_DOMAIN=y -CONFIG_GENERIC_PCI_IOMAP=y -CONFIG_GENERIC_PHY=y -CONFIG_GENERIC_PINCONF=y -CONFIG_GENERIC_PINCTRL_GROUPS=y -CONFIG_GENERIC_PINMUX_FUNCTIONS=y -CONFIG_GENERIC_SCHED_CLOCK=y -CONFIG_GENERIC_SMP_IDLE_THREAD=y -CONFIG_GENERIC_STRNCPY_FROM_USER=y -CONFIG_GENERIC_STRNLEN_USER=y -CONFIG_GENERIC_TIME_VSYSCALL=y -CONFIG_GLOB=y -CONFIG_GPIOLIB_IRQCHIP=y -CONFIG_GPIO_CDEV=y -CONFIG_HARDIRQS_SW_RESEND=y -CONFIG_HAS_DMA=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT_MAP=y -CONFIG_HWSPINLOCK=y -CONFIG_HWSPINLOCK_QCOM=y -CONFIG_I2C=y -CONFIG_I2C_BOARDINFO=y -CONFIG_I2C_CHARDEV=y -CONFIG_I2C_HELPER_AUTO=y -# CONFIG_I2C_QCOM_CCI is not set -CONFIG_I2C_QUP=y -CONFIG_IIO=y -CONFIG_ILLEGAL_POINTER_VALUE=0xdead000000000000 -CONFIG_INITRAMFS_SOURCE="" -CONFIG_IPQ_APSS_6018=y -CONFIG_IPQ_APSS_PLL=y -# CONFIG_IPQ_GCC_4019 is not set -# CONFIG_IPQ_GCC_6018 is not set -# CONFIG_IPQ_GCC_806X is not set -# CONFIG_IPQ_GCC_8074 is not set -# CONFIG_IPQ_LCC_806X is not set -CONFIG_IRQCHIP=y -CONFIG_IRQ_DOMAIN=y -CONFIG_IRQ_DOMAIN_HIERARCHY=y -CONFIG_IRQ_FASTEOI_HIERARCHY_HANDLERS=y -CONFIG_IRQ_FORCED_THREADING=y -CONFIG_IRQ_WORK=y -# CONFIG_KPSS_XCC is not set -CONFIG_LIBFDT=y -CONFIG_LOCK_DEBUGGING_SUPPORT=y -CONFIG_LOCK_SPIN_ON_OWNER=y -CONFIG_LZO_COMPRESS=y -CONFIG_LZO_DECOMPRESS=y -CONFIG_MAILBOX=y -# CONFIG_MAILBOX_TEST is not set -CONFIG_MDIO_BUS=y -CONFIG_MDIO_DEVICE=y -CONFIG_MDIO_DEVRES=y -CONFIG_MDIO_IPQ4019=y -# CONFIG_MDM_GCC_9615 is not set -# CONFIG_MDM_LCC_9615 is not set -CONFIG_MEMFD_CREATE=y -# CONFIG_MFD_QCOM_RPM is not set -CONFIG_MFD_SYSCON=y -CONFIG_MIGRATION=y -# CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY is not set -CONFIG_MMC=y -CONFIG_MMC_BLOCK=y -CONFIG_MMC_BLOCK_MINORS=32 -CONFIG_MMC_CQHCI=y -CONFIG_MMC_SDHCI=y -CONFIG_MMC_SDHCI_IO_ACCESSORS=y -CONFIG_MMC_SDHCI_MSM=y -# CONFIG_MMC_SDHCI_PCI is not set -CONFIG_MMC_SDHCI_PLTFM=y -CONFIG_MODULES_USE_ELF_RELA=y -# CONFIG_MSM_GCC_8660 is not set -# CONFIG_MSM_GCC_8909 is not set -# CONFIG_MSM_GCC_8916 is not set -# CONFIG_MSM_GCC_8939 is not set -# CONFIG_MSM_GCC_8960 is not set -# CONFIG_MSM_GCC_8974 is not set -# CONFIG_MSM_GCC_8976 is not set -# CONFIG_MSM_GCC_8994 is not set -# CONFIG_MSM_GCC_8996 is not set -# CONFIG_MSM_GCC_8998 is not set -# CONFIG_MSM_GPUCC_8998 is not set -# CONFIG_MSM_LCC_8960 is not set -# CONFIG_MSM_MMCC_8960 is not set -# CONFIG_MSM_MMCC_8974 is not set -# CONFIG_MSM_MMCC_8996 is not set -# CONFIG_MSM_MMCC_8998 is not set -CONFIG_MTD_NAND_CORE=y -CONFIG_MTD_NAND_ECC=y -CONFIG_MTD_NAND_ECC_SW_HAMMING=y -CONFIG_MTD_NAND_QCOM=y -CONFIG_MTD_QCOMSMEM_PARTS=y -CONFIG_MTD_RAW_NAND=y -CONFIG_MTD_SPI_NOR=y -CONFIG_MTD_UBI=y -CONFIG_MTD_UBI_BEB_LIMIT=20 -CONFIG_MTD_UBI_BLOCK=y -CONFIG_MTD_UBI_WL_THRESHOLD=4096 -CONFIG_MUTEX_SPIN_ON_OWNER=y -CONFIG_NEED_DMA_MAP_STATE=y -CONFIG_NEED_SG_DMA_LENGTH=y -CONFIG_NET_FLOW_LIMIT=y -CONFIG_NET_SELFTESTS=y -CONFIG_NET_SWITCHDEV=y -CONFIG_NLS=y -CONFIG_NO_HZ_COMMON=y -CONFIG_NO_HZ_IDLE=y -CONFIG_NR_CPUS=4 -CONFIG_NVIDIA_CARMEL_CNP_ERRATUM=y -CONFIG_NVMEM=y -CONFIG_NVMEM_LAYOUTS=y -CONFIG_NVMEM_QCOM_QFPROM=y -# CONFIG_NVMEM_QCOM_SEC_QFPROM is not set -CONFIG_NVMEM_SYSFS=y -CONFIG_NVMEM_U_BOOT_ENV=y -CONFIG_OF=y -CONFIG_OF_ADDRESS=y -CONFIG_OF_EARLY_FLATTREE=y -CONFIG_OF_FLATTREE=y -CONFIG_OF_GPIO=y -CONFIG_OF_IRQ=y -CONFIG_OF_KOBJ=y -CONFIG_OF_MDIO=y -CONFIG_PADATA=y -CONFIG_PAGE_POOL=y -CONFIG_PAGE_SIZE_LESS_THAN_256KB=y -CONFIG_PAGE_SIZE_LESS_THAN_64KB=y -CONFIG_PAHOLE_HAS_LANG_EXCLUDE=y -CONFIG_PARTITION_PERCPU=y -CONFIG_PCI=y -CONFIG_PCIEAER=y -CONFIG_PCIEASPM=y -CONFIG_PCIEASPM_DEFAULT=y -# CONFIG_PCIEASPM_PERFORMANCE is not set -# CONFIG_PCIEASPM_POWERSAVE is not set -# CONFIG_PCIEASPM_POWER_SUPERSAVE is not set -CONFIG_PCIEPORTBUS=y -CONFIG_PCIE_DW=y -CONFIG_PCIE_DW_HOST=y -CONFIG_PCIE_PME=y -CONFIG_PCIE_QCOM=y -CONFIG_PCI_DOMAINS=y -CONFIG_PCI_DOMAINS_GENERIC=y -CONFIG_PCI_MSI=y -CONFIG_PCI_MSI_IRQ_DOMAIN=y -CONFIG_PGTABLE_LEVELS=3 -CONFIG_PHYLIB=y -CONFIG_PHYLIB_LEDS=y -CONFIG_PHYS_ADDR_T_64BIT=y -# CONFIG_PHY_QCOM_APQ8064_SATA is not set -# CONFIG_PHY_QCOM_EDP is not set -# CONFIG_PHY_QCOM_IPQ4019_USB is not set -# CONFIG_PHY_QCOM_IPQ806X_SATA is not set -# CONFIG_PHY_QCOM_IPQ806X_USB is not set -# CONFIG_PHY_QCOM_PCIE2 is not set -CONFIG_PHY_QCOM_QMP=y -CONFIG_PHY_QCOM_QUSB2=y -# CONFIG_PHY_QCOM_USB_HS_28NM is not set -# CONFIG_PHY_QCOM_USB_SNPS_FEMTO_V2 is not set -# CONFIG_PHY_QCOM_USB_SS is not set -CONFIG_PINCTRL=y -# CONFIG_PINCTRL_IPQ6018 is not set -# CONFIG_PINCTRL_IPQ8074 is not set -CONFIG_PINCTRL_MSM=y -# CONFIG_PINCTRL_MSM8916 is not set -# CONFIG_PINCTRL_MSM8976 is not set -# CONFIG_PINCTRL_MSM8994 is not set -# CONFIG_PINCTRL_MSM8996 is not set -# CONFIG_PINCTRL_MSM8998 is not set -# CONFIG_PINCTRL_QCM2290 is not set -# CONFIG_PINCTRL_QCOM_SSBI_PMIC is not set -# CONFIG_PINCTRL_QCS404 is not set -# CONFIG_PINCTRL_SC7180 is not set -# CONFIG_PINCTRL_SC8280XP is not set -# CONFIG_PINCTRL_SDM660 is not set -# CONFIG_PINCTRL_SDM845 is not set -# CONFIG_PINCTRL_SM6350 is not set -# CONFIG_PINCTRL_SM6375 is not set -# CONFIG_PINCTRL_SM8150 is not set -# CONFIG_PINCTRL_SM8250 is not set -# CONFIG_PINCTRL_SM8450 is not set -CONFIG_PM=y -CONFIG_PM_CLK=y -CONFIG_PM_OPP=y -CONFIG_POSIX_CPU_TIMERS_TASK_WORK=y -CONFIG_POWER_RESET=y -# CONFIG_POWER_RESET_MSM is not set -CONFIG_POWER_SUPPLY=y -CONFIG_PREEMPT_NONE_BUILD=y -CONFIG_PRINTK_TIME=y -CONFIG_PTP_1588_CLOCK_OPTIONAL=y -CONFIG_QCA807X_PHY=y -CONFIG_QCA808X_PHY=y -# CONFIG_QCM_DISPCC_2290 is not set -# CONFIG_QCM_GCC_2290 is not set -# CONFIG_QCOM_A53PLL is not set -# CONFIG_QCOM_AOSS_QMP is not set -CONFIG_QCOM_APCS_IPC=y -# CONFIG_QCOM_APM is not set -# CONFIG_QCOM_APR is not set -CONFIG_QCOM_BAM_DMA=y -# CONFIG_QCOM_CLK_APCC_MSM8996 is not set -# CONFIG_QCOM_CLK_APCS_MSM8916 is not set -# CONFIG_QCOM_CLK_APCS_SDX55 is not set -# CONFIG_QCOM_COMMAND_DB is not set -# CONFIG_QCOM_CPR is not set -# CONFIG_QCOM_EBI2 is not set -# CONFIG_QCOM_FASTRPC is not set -# CONFIG_QCOM_GENI_SE is not set -# CONFIG_QCOM_GSBI is not set -# CONFIG_QCOM_HFPLL is not set -# CONFIG_QCOM_ICC_BWMON is not set -# CONFIG_QCOM_IPCC is not set -# CONFIG_QCOM_LLCC is not set -CONFIG_QCOM_MDT_LOADER=y -# CONFIG_QCOM_MPM is not set -CONFIG_QCOM_NET_PHYLIB=y -# CONFIG_QCOM_OCMEM is not set -# CONFIG_QCOM_PDC is not set -CONFIG_QCOM_PIL_INFO=y -# CONFIG_QCOM_Q6V5_ADSP is not set -CONFIG_QCOM_Q6V5_COMMON=y -# CONFIG_QCOM_Q6V5_MSS is not set -# CONFIG_QCOM_Q6V5_PAS is not set -CONFIG_QCOM_Q6V5_WCSS=y -# CONFIG_QCOM_RMTFS_MEM is not set -# CONFIG_QCOM_RPMH is not set -CONFIG_QCOM_RPROC_COMMON=y -CONFIG_QCOM_SCM=y -# CONFIG_QCOM_SCM_DOWNLOAD_MODE_DEFAULT is not set -# CONFIG_QCOM_SMD_RPM is not set -CONFIG_QCOM_SMEM=y -CONFIG_QCOM_SMEM_STATE=y -CONFIG_QCOM_SMP2P=y -# CONFIG_QCOM_SMSM is not set -CONFIG_QCOM_SOCINFO=y -# CONFIG_QCOM_SPM is not set -# CONFIG_QCOM_STATS is not set -# CONFIG_QCOM_SYSMON is not set -CONFIG_QCOM_TSENS=y -# CONFIG_QCOM_WCNSS_CTRL is not set -# CONFIG_QCOM_WCNSS_PIL is not set -CONFIG_QCOM_WDT=y -# CONFIG_QCS_GCC_404 is not set -# CONFIG_QCS_Q6SSTOP_404 is not set -# CONFIG_QCS_TURING_404 is not set -CONFIG_QUEUED_RWLOCKS=y -CONFIG_QUEUED_SPINLOCKS=y -CONFIG_RANDSTRUCT_NONE=y -CONFIG_RAS=y -CONFIG_RATIONAL=y -CONFIG_REGMAP=y -CONFIG_REGMAP_MMIO=y -CONFIG_REGULATOR=y -# CONFIG_REGULATOR_CPR3 is not set -CONFIG_REGULATOR_FIXED_VOLTAGE=y -# CONFIG_REGULATOR_VQMMC_IPQ4019 is not set -CONFIG_RELOCATABLE=y -CONFIG_REMOTEPROC=y -CONFIG_REMOTEPROC_CDEV=y -CONFIG_RESET_CONTROLLER=y -# CONFIG_RESET_QCOM_AOSS is not set -# CONFIG_RESET_QCOM_PDC is not set -CONFIG_RFS_ACCEL=y -CONFIG_RODATA_FULL_DEFAULT_ENABLED=y -CONFIG_RPMSG=y -CONFIG_RPMSG_CHAR=y -# CONFIG_RPMSG_CTRL is not set -# CONFIG_RPMSG_NS is not set -CONFIG_RPMSG_QCOM_GLINK=y -CONFIG_RPMSG_QCOM_GLINK_RPM=y -CONFIG_RPMSG_QCOM_GLINK_SMEM=y -CONFIG_RPMSG_QCOM_SMD=y -# CONFIG_RPMSG_TTY is not set -CONFIG_RPS=y -CONFIG_RTC_CLASS=y -CONFIG_RTC_I2C_AND_SPI=y -CONFIG_RWSEM_SPIN_ON_OWNER=y -# CONFIG_SCHED_CORE is not set -CONFIG_SCHED_MC=y -CONFIG_SCHED_SMT=y -CONFIG_SCHED_THERMAL_PRESSURE=y -CONFIG_SCSI=y -CONFIG_SCSI_COMMON=y -# CONFIG_SCSI_LOWLEVEL is not set -# CONFIG_SCSI_PROC_FS is not set -# CONFIG_SC_CAMCC_7280 is not set -# CONFIG_SC_DISPCC_7180 is not set -# CONFIG_SC_GCC_7180 is not set -# CONFIG_SC_GCC_8280XP is not set -# CONFIG_SC_GPUCC_7180 is not set -# CONFIG_SC_LPASSCC_7280 is not set -# CONFIG_SC_LPASS_CORECC_7180 is not set -# CONFIG_SC_LPASS_CORECC_7280 is not set -# CONFIG_SC_MSS_7180 is not set -# CONFIG_SC_VIDEOCC_7180 is not set -# CONFIG_SDM_CAMCC_845 is not set -# CONFIG_SDM_DISPCC_845 is not set -# CONFIG_SDM_GCC_660 is not set -# CONFIG_SDM_GCC_845 is not set -# CONFIG_SDM_GPUCC_845 is not set -# CONFIG_SDM_LPASSCC_845 is not set -# CONFIG_SDM_VIDEOCC_845 is not set -# CONFIG_SDX_GCC_65 is not set -CONFIG_SERIAL_8250_FSL=y -CONFIG_SERIAL_MCTRL_GPIO=y -CONFIG_SERIAL_MSM=y -CONFIG_SERIAL_MSM_CONSOLE=y -CONFIG_SGL_ALLOC=y -CONFIG_SG_POOL=y -CONFIG_SMP=y -# CONFIG_SM_CAMCC_8450 is not set -# CONFIG_SM_GCC_8150 is not set -# CONFIG_SM_GCC_8250 is not set -# CONFIG_SM_GCC_8450 is not set -# CONFIG_SM_GPUCC_6350 is not set -# CONFIG_SM_GPUCC_8150 is not set -# CONFIG_SM_GPUCC_8250 is not set -# CONFIG_SM_GPUCC_8350 is not set -# CONFIG_SM_VIDEOCC_8150 is not set -# CONFIG_SM_VIDEOCC_8250 is not set -CONFIG_SOCK_RX_QUEUE_MAPPING=y -CONFIG_SOC_BUS=y -CONFIG_SOFTIRQ_ON_OWN_STACK=y -CONFIG_SPARSEMEM=y -CONFIG_SPARSEMEM_EXTREME=y -CONFIG_SPARSEMEM_VMEMMAP=y -CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y -CONFIG_SPARSE_IRQ=y -CONFIG_SPI=y -CONFIG_SPI_MASTER=y -CONFIG_SPI_MEM=y -CONFIG_SPI_QUP=y -CONFIG_SRCU=y -CONFIG_SWIOTLB=y -CONFIG_SWPHY=y -CONFIG_SYSCTL_EXCEPTION_TRACE=y -CONFIG_THERMAL=y -CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y -CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0 -CONFIG_THERMAL_GOV_STEP_WISE=y -CONFIG_THERMAL_OF=y -CONFIG_THREAD_INFO_IN_TASK=y -CONFIG_TICK_CPU_ACCOUNTING=y -CONFIG_TIMER_OF=y -CONFIG_TIMER_PROBE=y -CONFIG_TRACE_IRQFLAGS_NMI_SUPPORT=y -CONFIG_TREE_RCU=y -CONFIG_TREE_SRCU=y -CONFIG_UBIFS_FS=y -CONFIG_UBIFS_FS_ADVANCED_COMPR=y -# CONFIG_UCLAMP_TASK is not set -CONFIG_UNMAP_KERNEL_AT_EL0=y -CONFIG_USB=y -CONFIG_USB_COMMON=y -CONFIG_USB_SUPPORT=y -CONFIG_VIRTIO=y -CONFIG_VIRTIO_ANCHOR=y -# CONFIG_VIRTIO_BLK is not set -# CONFIG_VIRTIO_NET is not set -CONFIG_VMAP_STACK=y -CONFIG_WANT_DEV_COREDUMP=y -CONFIG_WATCHDOG_CORE=y -CONFIG_WATCHDOG_SYSFS=y -CONFIG_XPS=y -CONFIG_XXHASH=y -CONFIG_ZLIB_DEFLATE=y -CONFIG_ZLIB_INFLATE=y -CONFIG_ZONE_DMA32=y -CONFIG_ZSTD_COMMON=y -CONFIG_ZSTD_COMPRESS=y -CONFIG_ZSTD_DECOMPRESS=y diff --git a/target/linux/qualcommax/patches-6.1/0001-v6.2-arm64-dts-qcom-ipq8074-add-A53-PLL-node.patch b/target/linux/qualcommax/patches-6.1/0001-v6.2-arm64-dts-qcom-ipq8074-add-A53-PLL-node.patch deleted file mode 100644 index 5a4b1bbc99..0000000000 --- a/target/linux/qualcommax/patches-6.1/0001-v6.2-arm64-dts-qcom-ipq8074-add-A53-PLL-node.patch +++ /dev/null @@ -1,32 +0,0 @@ -From 6463c10bfdbd684ec7ecfd408ea541283215a088 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Fri, 19 Aug 2022 00:06:28 +0200 -Subject: [PATCH] arm64: dts: qcom: ipq8074: add A53 PLL node - -Add the required node for A53 PLL which will be used to provide the CPU -clock via APCS for APSS scaling. - -Signed-off-by: Robert Marko -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20220818220628.339366-9-robimarko@gmail.com ---- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 8 ++++++++ - 1 file changed, 8 insertions(+) - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -677,6 +677,14 @@ - #mbox-cells = <1>; - }; - -+ a53pll: clock@b116000 { -+ compatible = "qcom,ipq8074-a53pll"; -+ reg = <0x0b116000 0x40>; -+ #clock-cells = <0>; -+ clocks = <&xo>; -+ clock-names = "xo"; -+ }; -+ - timer@b120000 { - #address-cells = <1>; - #size-cells = <1>; diff --git a/target/linux/qualcommax/patches-6.1/0002-v6.2-thermal-drivers-tsens-Add-support-for-combined-inter.patch b/target/linux/qualcommax/patches-6.1/0002-v6.2-thermal-drivers-tsens-Add-support-for-combined-inter.patch deleted file mode 100644 index 0320725999..0000000000 --- a/target/linux/qualcommax/patches-6.1/0002-v6.2-thermal-drivers-tsens-Add-support-for-combined-inter.patch +++ /dev/null @@ -1,134 +0,0 @@ -From e593e834fe8ba9bf314d8215ac05d8787f81efda Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Fri, 19 Aug 2022 00:02:42 +0200 -Subject: [PATCH] thermal/drivers/tsens: Add support for combined interrupt - -Despite using tsens v2.3 IP, IPQ8074 and IPQ6018 only have one IRQ for -signaling both up/low and critical trips. - -Signed-off-by: Robert Marko -Reviewed-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20220818220245.338396-2-robimarko@gmail.com -Signed-off-by: Daniel Lezcano ---- - drivers/thermal/qcom/tsens-8960.c | 1 + - drivers/thermal/qcom/tsens-v0_1.c | 1 + - drivers/thermal/qcom/tsens-v1.c | 1 + - drivers/thermal/qcom/tsens-v2.c | 1 + - drivers/thermal/qcom/tsens.c | 38 ++++++++++++++++++++++++++----- - drivers/thermal/qcom/tsens.h | 2 ++ - 6 files changed, 38 insertions(+), 6 deletions(-) - ---- a/drivers/thermal/qcom/tsens-8960.c -+++ b/drivers/thermal/qcom/tsens-8960.c -@@ -269,6 +269,7 @@ static const struct tsens_ops ops_8960 = - static struct tsens_features tsens_8960_feat = { - .ver_major = VER_0, - .crit_int = 0, -+ .combo_int = 0, - .adc = 1, - .srot_split = 0, - .max_sensors = 11, ---- a/drivers/thermal/qcom/tsens-v0_1.c -+++ b/drivers/thermal/qcom/tsens-v0_1.c -@@ -549,6 +549,7 @@ static int __init init_8939(struct tsens - static struct tsens_features tsens_v0_1_feat = { - .ver_major = VER_0_1, - .crit_int = 0, -+ .combo_int = 0, - .adc = 1, - .srot_split = 1, - .max_sensors = 11, ---- a/drivers/thermal/qcom/tsens-v1.c -+++ b/drivers/thermal/qcom/tsens-v1.c -@@ -273,6 +273,7 @@ static int calibrate_8976(struct tsens_p - static struct tsens_features tsens_v1_feat = { - .ver_major = VER_1_X, - .crit_int = 0, -+ .combo_int = 0, - .adc = 1, - .srot_split = 1, - .max_sensors = 11, ---- a/drivers/thermal/qcom/tsens-v2.c -+++ b/drivers/thermal/qcom/tsens-v2.c -@@ -31,6 +31,7 @@ - static struct tsens_features tsens_v2_feat = { - .ver_major = VER_2_X, - .crit_int = 1, -+ .combo_int = 0, - .adc = 0, - .srot_split = 1, - .max_sensors = 16, ---- a/drivers/thermal/qcom/tsens.c -+++ b/drivers/thermal/qcom/tsens.c -@@ -532,6 +532,27 @@ static irqreturn_t tsens_irq_thread(int - return IRQ_HANDLED; - } - -+/** -+ * tsens_combined_irq_thread() - Threaded interrupt handler for combined interrupts -+ * @irq: irq number -+ * @data: tsens controller private data -+ * -+ * Handle the combined interrupt as if it were 2 separate interrupts, so call the -+ * critical handler first and then the up/low one. -+ * -+ * Return: IRQ_HANDLED -+ */ -+static irqreturn_t tsens_combined_irq_thread(int irq, void *data) -+{ -+ irqreturn_t ret; -+ -+ ret = tsens_critical_irq_thread(irq, data); -+ if (ret != IRQ_HANDLED) -+ return ret; -+ -+ return tsens_irq_thread(irq, data); -+} -+ - static int tsens_set_trips(struct thermal_zone_device *tz, int low, int high) - { - struct tsens_sensor *s = tz->devdata; -@@ -1074,13 +1095,18 @@ static int tsens_register(struct tsens_p - tsens_mC_to_hw(priv->sensor, 0)); - } - -- ret = tsens_register_irq(priv, "uplow", tsens_irq_thread); -- if (ret < 0) -- return ret; -+ if (priv->feat->combo_int) { -+ ret = tsens_register_irq(priv, "combined", -+ tsens_combined_irq_thread); -+ } else { -+ ret = tsens_register_irq(priv, "uplow", tsens_irq_thread); -+ if (ret < 0) -+ return ret; - -- if (priv->feat->crit_int) -- ret = tsens_register_irq(priv, "critical", -- tsens_critical_irq_thread); -+ if (priv->feat->crit_int) -+ ret = tsens_register_irq(priv, "critical", -+ tsens_critical_irq_thread); -+ } - - return ret; - } ---- a/drivers/thermal/qcom/tsens.h -+++ b/drivers/thermal/qcom/tsens.h -@@ -493,6 +493,7 @@ enum regfield_ids { - * struct tsens_features - Features supported by the IP - * @ver_major: Major number of IP version - * @crit_int: does the IP support critical interrupts? -+ * @combo_int: does the IP use one IRQ for up, low and critical thresholds? - * @adc: do the sensors only output adc code (instead of temperature)? - * @srot_split: does the IP neatly splits the register space into SROT and TM, - * with SROT only being available to secure boot firmware? -@@ -502,6 +503,7 @@ enum regfield_ids { - struct tsens_features { - unsigned int ver_major; - unsigned int crit_int:1; -+ unsigned int combo_int:1; - unsigned int adc:1; - unsigned int srot_split:1; - unsigned int has_watchdog:1; diff --git a/target/linux/qualcommax/patches-6.1/0003-v6.2-thermal-drivers-tsens-Allow-configuring-min-and-max-.patch b/target/linux/qualcommax/patches-6.1/0003-v6.2-thermal-drivers-tsens-Allow-configuring-min-and-max-.patch deleted file mode 100644 index 363061813a..0000000000 --- a/target/linux/qualcommax/patches-6.1/0003-v6.2-thermal-drivers-tsens-Allow-configuring-min-and-max-.patch +++ /dev/null @@ -1,101 +0,0 @@ -From 7805365fee582056b32c69cf35aafbb94b14a8ca Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Fri, 19 Aug 2022 00:02:43 +0200 -Subject: [PATCH] thermal/drivers/tsens: Allow configuring min and max trips - -IPQ8074 and IPQ6018 dont support negative trip temperatures and support -up to 204 degrees C as the max trip temperature. - -So, instead of always setting the -40 as min and 120 degrees C as max -allow it to be configured as part of the features. - -Signed-off-by: Robert Marko -Reviewed-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20220818220245.338396-3-robimarko@gmail.com -Signed-off-by: Daniel Lezcano ---- - drivers/thermal/qcom/tsens-8960.c | 2 ++ - drivers/thermal/qcom/tsens-v0_1.c | 2 ++ - drivers/thermal/qcom/tsens-v1.c | 2 ++ - drivers/thermal/qcom/tsens-v2.c | 2 ++ - drivers/thermal/qcom/tsens.c | 4 ++-- - drivers/thermal/qcom/tsens.h | 4 ++++ - 6 files changed, 14 insertions(+), 2 deletions(-) - ---- a/drivers/thermal/qcom/tsens-8960.c -+++ b/drivers/thermal/qcom/tsens-8960.c -@@ -273,6 +273,8 @@ static struct tsens_features tsens_8960_ - .adc = 1, - .srot_split = 0, - .max_sensors = 11, -+ .trip_min_temp = -40000, -+ .trip_max_temp = 120000, - }; - - struct tsens_plat_data data_8960 = { ---- a/drivers/thermal/qcom/tsens-v0_1.c -+++ b/drivers/thermal/qcom/tsens-v0_1.c -@@ -553,6 +553,8 @@ static struct tsens_features tsens_v0_1_ - .adc = 1, - .srot_split = 1, - .max_sensors = 11, -+ .trip_min_temp = -40000, -+ .trip_max_temp = 120000, - }; - - static const struct reg_field tsens_v0_1_regfields[MAX_REGFIELDS] = { ---- a/drivers/thermal/qcom/tsens-v1.c -+++ b/drivers/thermal/qcom/tsens-v1.c -@@ -277,6 +277,8 @@ static struct tsens_features tsens_v1_fe - .adc = 1, - .srot_split = 1, - .max_sensors = 11, -+ .trip_min_temp = -40000, -+ .trip_max_temp = 120000, - }; - - static const struct reg_field tsens_v1_regfields[MAX_REGFIELDS] = { ---- a/drivers/thermal/qcom/tsens-v2.c -+++ b/drivers/thermal/qcom/tsens-v2.c -@@ -35,6 +35,8 @@ static struct tsens_features tsens_v2_fe - .adc = 0, - .srot_split = 1, - .max_sensors = 16, -+ .trip_min_temp = -40000, -+ .trip_max_temp = 120000, - }; - - static const struct reg_field tsens_v2_regfields[MAX_REGFIELDS] = { ---- a/drivers/thermal/qcom/tsens.c -+++ b/drivers/thermal/qcom/tsens.c -@@ -573,8 +573,8 @@ static int tsens_set_trips(struct therma - dev_dbg(dev, "[%u] %s: proposed thresholds: (%d:%d)\n", - hw_id, __func__, low, high); - -- cl_high = clamp_val(high, -40000, 120000); -- cl_low = clamp_val(low, -40000, 120000); -+ cl_high = clamp_val(high, priv->feat->trip_min_temp, priv->feat->trip_max_temp); -+ cl_low = clamp_val(low, priv->feat->trip_min_temp, priv->feat->trip_max_temp); - - high_val = tsens_mC_to_hw(s, cl_high); - low_val = tsens_mC_to_hw(s, cl_low); ---- a/drivers/thermal/qcom/tsens.h -+++ b/drivers/thermal/qcom/tsens.h -@@ -499,6 +499,8 @@ enum regfield_ids { - * with SROT only being available to secure boot firmware? - * @has_watchdog: does this IP support watchdog functionality? - * @max_sensors: maximum sensors supported by this version of the IP -+ * @trip_min_temp: minimum trip temperature supported by this version of the IP -+ * @trip_max_temp: maximum trip temperature supported by this version of the IP - */ - struct tsens_features { - unsigned int ver_major; -@@ -508,6 +510,8 @@ struct tsens_features { - unsigned int srot_split:1; - unsigned int has_watchdog:1; - unsigned int max_sensors; -+ int trip_min_temp; -+ int trip_max_temp; - }; - - /** diff --git a/target/linux/qualcommax/patches-6.1/0004-v6.2-thermal-drivers-tsens-Add-IPQ8074-support.patch b/target/linux/qualcommax/patches-6.1/0004-v6.2-thermal-drivers-tsens-Add-IPQ8074-support.patch deleted file mode 100644 index eaea693959..0000000000 --- a/target/linux/qualcommax/patches-6.1/0004-v6.2-thermal-drivers-tsens-Add-IPQ8074-support.patch +++ /dev/null @@ -1,74 +0,0 @@ -From 0164d794cbc58488a7321272e95958d10cf103a4 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Fri, 19 Aug 2022 00:02:44 +0200 -Subject: [PATCH] thermal/drivers/tsens: Add IPQ8074 support - -Qualcomm IPQ8074 uses tsens v2.3 IP, however unlike other tsens v2 IP -it only has one IRQ, that is used for up/low as well as critical. -It also does not support negative trip temperatures. - -Signed-off-by: Robert Marko -Reviewed-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20220818220245.338396-4-robimarko@gmail.com -Signed-off-by: Daniel Lezcano ---- - drivers/thermal/qcom/tsens-v2.c | 17 +++++++++++++++++ - drivers/thermal/qcom/tsens.c | 3 +++ - drivers/thermal/qcom/tsens.h | 2 +- - 3 files changed, 21 insertions(+), 1 deletion(-) - ---- a/drivers/thermal/qcom/tsens-v2.c -+++ b/drivers/thermal/qcom/tsens-v2.c -@@ -39,6 +39,17 @@ static struct tsens_features tsens_v2_fe - .trip_max_temp = 120000, - }; - -+static struct tsens_features ipq8074_feat = { -+ .ver_major = VER_2_X, -+ .crit_int = 1, -+ .combo_int = 1, -+ .adc = 0, -+ .srot_split = 1, -+ .max_sensors = 16, -+ .trip_min_temp = 0, -+ .trip_max_temp = 204000, -+}; -+ - static const struct reg_field tsens_v2_regfields[MAX_REGFIELDS] = { - /* ----- SROT ------ */ - /* VERSION */ -@@ -104,6 +115,12 @@ struct tsens_plat_data data_tsens_v2 = { - .fields = tsens_v2_regfields, - }; - -+struct tsens_plat_data data_ipq8074 = { -+ .ops = &ops_generic_v2, -+ .feat = &ipq8074_feat, -+ .fields = tsens_v2_regfields, -+}; -+ - /* Kept around for backward compatibility with old msm8996.dtsi */ - struct tsens_plat_data data_8996 = { - .num_sensors = 13, ---- a/drivers/thermal/qcom/tsens.c -+++ b/drivers/thermal/qcom/tsens.c -@@ -981,6 +981,9 @@ static const struct of_device_id tsens_t - .compatible = "qcom,ipq8064-tsens", - .data = &data_8960, - }, { -+ .compatible = "qcom,ipq8074-tsens", -+ .data = &data_ipq8074, -+ }, { - .compatible = "qcom,mdm9607-tsens", - .data = &data_9607, - }, { ---- a/drivers/thermal/qcom/tsens.h -+++ b/drivers/thermal/qcom/tsens.h -@@ -597,6 +597,6 @@ extern struct tsens_plat_data data_8916, - extern struct tsens_plat_data data_tsens_v1, data_8976, data_8956; - - /* TSENS v2 targets */ --extern struct tsens_plat_data data_8996, data_tsens_v2; -+extern struct tsens_plat_data data_8996, data_ipq8074, data_tsens_v2; - - #endif /* __QCOM_TSENS_H__ */ diff --git a/target/linux/qualcommax/patches-6.1/0005-v6.2-arm64-dts-qcom-ipq8074-add-thermal-nodes.patch b/target/linux/qualcommax/patches-6.1/0005-v6.2-arm64-dts-qcom-ipq8074-add-thermal-nodes.patch deleted file mode 100644 index f5abd27965..0000000000 --- a/target/linux/qualcommax/patches-6.1/0005-v6.2-arm64-dts-qcom-ipq8074-add-thermal-nodes.patch +++ /dev/null @@ -1,130 +0,0 @@ -From c3cc0c2a17f552be2426200e47a9e2c62cf449ce Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Fri, 19 Aug 2022 00:02:45 +0200 -Subject: [PATCH] arm64: dts: qcom: ipq8074: add thermal nodes - -IPQ8074 has a tsens v2.3.0 peripheral which monitors -temperatures around the various subsystems on the -die. - -So lets add the tsens and thermal zone nodes, passive -CPU cooling will come in later patches after CPU frequency -scaling is supported. - -Signed-off-by: Robert Marko -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20220818220245.338396-5-robimarko@gmail.com ---- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 96 +++++++++++++++++++++++++++ - 1 file changed, 96 insertions(+) - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -276,6 +276,16 @@ - status = "disabled"; - }; - -+ tsens: thermal-sensor@4a9000 { -+ compatible = "qcom,ipq8074-tsens"; -+ reg = <0x4a9000 0x1000>, /* TM */ -+ <0x4a8000 0x1000>; /* SROT */ -+ interrupts = ; -+ interrupt-names = "combined"; -+ #qcom,sensors = <16>; -+ #thermal-sensor-cells = <1>; -+ }; -+ - cryptobam: dma-controller@704000 { - compatible = "qcom,bam-v1.7.0"; - reg = <0x00704000 0x20000>; -@@ -876,4 +886,90 @@ - , - ; - }; -+ -+ thermal-zones { -+ nss-top-thermal { -+ polling-delay-passive = <250>; -+ polling-delay = <1000>; -+ -+ thermal-sensors = <&tsens 4>; -+ }; -+ -+ nss0-thermal { -+ polling-delay-passive = <250>; -+ polling-delay = <1000>; -+ -+ thermal-sensors = <&tsens 5>; -+ }; -+ -+ nss1-thermal { -+ polling-delay-passive = <250>; -+ polling-delay = <1000>; -+ -+ thermal-sensors = <&tsens 6>; -+ }; -+ -+ wcss-phya0-thermal { -+ polling-delay-passive = <250>; -+ polling-delay = <1000>; -+ -+ thermal-sensors = <&tsens 7>; -+ }; -+ -+ wcss-phya1-thermal { -+ polling-delay-passive = <250>; -+ polling-delay = <1000>; -+ -+ thermal-sensors = <&tsens 8>; -+ }; -+ -+ cpu0_thermal: cpu0-thermal { -+ polling-delay-passive = <250>; -+ polling-delay = <1000>; -+ -+ thermal-sensors = <&tsens 9>; -+ }; -+ -+ cpu1_thermal: cpu1-thermal { -+ polling-delay-passive = <250>; -+ polling-delay = <1000>; -+ -+ thermal-sensors = <&tsens 10>; -+ }; -+ -+ cpu2_thermal: cpu2-thermal { -+ polling-delay-passive = <250>; -+ polling-delay = <1000>; -+ -+ thermal-sensors = <&tsens 11>; -+ }; -+ -+ cpu3_thermal: cpu3-thermal { -+ polling-delay-passive = <250>; -+ polling-delay = <1000>; -+ -+ thermal-sensors = <&tsens 12>; -+ }; -+ -+ cluster_thermal: cluster-thermal { -+ polling-delay-passive = <250>; -+ polling-delay = <1000>; -+ -+ thermal-sensors = <&tsens 13>; -+ }; -+ -+ wcss-phyb0-thermal { -+ polling-delay-passive = <250>; -+ polling-delay = <1000>; -+ -+ thermal-sensors = <&tsens 14>; -+ }; -+ -+ wcss-phyb1-thermal { -+ polling-delay-passive = <250>; -+ polling-delay = <1000>; -+ -+ thermal-sensors = <&tsens 15>; -+ }; -+ }; - }; diff --git a/target/linux/qualcommax/patches-6.1/0006-v6.2-arm64-dts-qcom-ipq8074-add-clocks-to-APCS.patch b/target/linux/qualcommax/patches-6.1/0006-v6.2-arm64-dts-qcom-ipq8074-add-clocks-to-APCS.patch deleted file mode 100644 index 96b49e60bf..0000000000 --- a/target/linux/qualcommax/patches-6.1/0006-v6.2-arm64-dts-qcom-ipq8074-add-clocks-to-APCS.patch +++ /dev/null @@ -1,29 +0,0 @@ -From 0df592a0a1a3fff9133977192677aa915afc174f Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Fri, 19 Aug 2022 00:08:49 +0200 -Subject: [PATCH] arm64: dts: qcom: ipq8074: add clocks to APCS - -APCS now has support for providing the APSS clocks as the child device -for IPQ8074. - -So, add the A53 PLL and XO clocks in order to use APCS as the CPU -clocksource for APSS scaling. - -Signed-off-by: Robert Marko -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20220818220849.339732-4-robimarko@gmail.com ---- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 2 ++ - 1 file changed, 2 insertions(+) - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -682,6 +682,8 @@ - apcs_glb: mailbox@b111000 { - compatible = "qcom,ipq8074-apcs-apps-global"; - reg = <0x0b111000 0x1000>; -+ clocks = <&a53pll>, <&xo>; -+ clock-names = "pll", "xo"; - - #clock-cells = <1>; - #mbox-cells = <1>; diff --git a/target/linux/qualcommax/patches-6.1/0007-v6.2-clk-qcom-ipq8074-convert-to-parent-data.patch b/target/linux/qualcommax/patches-6.1/0007-v6.2-clk-qcom-ipq8074-convert-to-parent-data.patch deleted file mode 100644 index c209adbc06..0000000000 --- a/target/linux/qualcommax/patches-6.1/0007-v6.2-clk-qcom-ipq8074-convert-to-parent-data.patch +++ /dev/null @@ -1,3601 +0,0 @@ -From e6c5115d6845f25eda7e162dcd783a2044215867 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Sun, 30 Oct 2022 18:57:01 +0100 -Subject: [PATCH] clk: qcom: ipq8074: convert to parent data - -Convert the IPQ8074 GCC driver to use parent data instead of global -name matching. - -Utilize ARRAY_SIZE for num_parents instead of hardcoding the value. - -Signed-off-by: Robert Marko -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20221030175703.1103224-1-robimarko@gmail.com ---- - drivers/clk/qcom/gcc-ipq8074.c | 1781 +++++++++++++++----------------- - 1 file changed, 813 insertions(+), 968 deletions(-) - ---- a/drivers/clk/qcom/gcc-ipq8074.c -+++ b/drivers/clk/qcom/gcc-ipq8074.c -@@ -49,349 +49,6 @@ enum { - P_UNIPHY2_TX, - }; - --static const char * const gcc_xo_gpll0_gpll0_out_main_div2[] = { -- "xo", -- "gpll0", -- "gpll0_out_main_div2", --}; -- --static const struct parent_map gcc_xo_gpll0_gpll0_out_main_div2_map[] = { -- { P_XO, 0 }, -- { P_GPLL0, 1 }, -- { P_GPLL0_DIV2, 4 }, --}; -- --static const struct parent_map gcc_xo_gpll0_map[] = { -- { P_XO, 0 }, -- { P_GPLL0, 1 }, --}; -- --static const char * const gcc_xo_gpll0_gpll2_gpll0_out_main_div2[] = { -- "xo", -- "gpll0", -- "gpll2", -- "gpll0_out_main_div2", --}; -- --static const struct parent_map gcc_xo_gpll0_gpll2_gpll0_out_main_div2_map[] = { -- { P_XO, 0 }, -- { P_GPLL0, 1 }, -- { P_GPLL2, 2 }, -- { P_GPLL0_DIV2, 4 }, --}; -- --static const char * const gcc_xo_gpll0_sleep_clk[] = { -- "xo", -- "gpll0", -- "sleep_clk", --}; -- --static const struct parent_map gcc_xo_gpll0_sleep_clk_map[] = { -- { P_XO, 0 }, -- { P_GPLL0, 2 }, -- { P_SLEEP_CLK, 6 }, --}; -- --static const char * const gcc_xo_gpll6_gpll0_gpll0_out_main_div2[] = { -- "xo", -- "gpll6", -- "gpll0", -- "gpll0_out_main_div2", --}; -- --static const struct parent_map gcc_xo_gpll6_gpll0_gpll0_out_main_div2_map[] = { -- { P_XO, 0 }, -- { P_GPLL6, 1 }, -- { P_GPLL0, 3 }, -- { P_GPLL0_DIV2, 4 }, --}; -- --static const char * const gcc_xo_gpll0_out_main_div2_gpll0[] = { -- "xo", -- "gpll0_out_main_div2", -- "gpll0", --}; -- --static const struct parent_map gcc_xo_gpll0_out_main_div2_gpll0_map[] = { -- { P_XO, 0 }, -- { P_GPLL0_DIV2, 2 }, -- { P_GPLL0, 1 }, --}; -- --static const char * const gcc_usb3phy_0_cc_pipe_clk_xo[] = { -- "usb3phy_0_cc_pipe_clk", -- "xo", --}; -- --static const struct parent_map gcc_usb3phy_0_cc_pipe_clk_xo_map[] = { -- { P_USB3PHY_0_PIPE, 0 }, -- { P_XO, 2 }, --}; -- --static const char * const gcc_usb3phy_1_cc_pipe_clk_xo[] = { -- "usb3phy_1_cc_pipe_clk", -- "xo", --}; -- --static const struct parent_map gcc_usb3phy_1_cc_pipe_clk_xo_map[] = { -- { P_USB3PHY_1_PIPE, 0 }, -- { P_XO, 2 }, --}; -- --static const char * const gcc_pcie20_phy0_pipe_clk_xo[] = { -- "pcie20_phy0_pipe_clk", -- "xo", --}; -- --static const struct parent_map gcc_pcie20_phy0_pipe_clk_xo_map[] = { -- { P_PCIE20_PHY0_PIPE, 0 }, -- { P_XO, 2 }, --}; -- --static const char * const gcc_pcie20_phy1_pipe_clk_xo[] = { -- "pcie20_phy1_pipe_clk", -- "xo", --}; -- --static const struct parent_map gcc_pcie20_phy1_pipe_clk_xo_map[] = { -- { P_PCIE20_PHY1_PIPE, 0 }, -- { P_XO, 2 }, --}; -- --static const char * const gcc_xo_gpll0_gpll6_gpll0_div2[] = { -- "xo", -- "gpll0", -- "gpll6", -- "gpll0_out_main_div2", --}; -- --static const struct parent_map gcc_xo_gpll0_gpll6_gpll0_div2_map[] = { -- { P_XO, 0 }, -- { P_GPLL0, 1 }, -- { P_GPLL6, 2 }, -- { P_GPLL0_DIV2, 4 }, --}; -- --static const char * const gcc_xo_gpll0_gpll6_gpll0_out_main_div2[] = { -- "xo", -- "gpll0", -- "gpll6", -- "gpll0_out_main_div2", --}; -- --static const struct parent_map gcc_xo_gpll0_gpll6_gpll0_out_main_div2_map[] = { -- { P_XO, 0 }, -- { P_GPLL0, 1 }, -- { P_GPLL6, 2 }, -- { P_GPLL0_DIV2, 3 }, --}; -- --static const char * const gcc_xo_bias_pll_nss_noc_clk_gpll0_gpll2[] = { -- "xo", -- "bias_pll_nss_noc_clk", -- "gpll0", -- "gpll2", --}; -- --static const struct parent_map gcc_xo_bias_pll_nss_noc_clk_gpll0_gpll2_map[] = { -- { P_XO, 0 }, -- { P_BIAS_PLL_NSS_NOC, 1 }, -- { P_GPLL0, 2 }, -- { P_GPLL2, 3 }, --}; -- --static const char * const gcc_xo_nss_crypto_pll_gpll0[] = { -- "xo", -- "nss_crypto_pll", -- "gpll0", --}; -- --static const struct parent_map gcc_xo_nss_crypto_pll_gpll0_map[] = { -- { P_XO, 0 }, -- { P_NSS_CRYPTO_PLL, 1 }, -- { P_GPLL0, 2 }, --}; -- --static const char * const gcc_xo_ubi32_pll_gpll0_gpll2_gpll4_gpll6[] = { -- "xo", -- "ubi32_pll", -- "gpll0", -- "gpll2", -- "gpll4", -- "gpll6", --}; -- --static const struct parent_map gcc_xo_ubi32_gpll0_gpll2_gpll4_gpll6_map[] = { -- { P_XO, 0 }, -- { P_UBI32_PLL, 1 }, -- { P_GPLL0, 2 }, -- { P_GPLL2, 3 }, -- { P_GPLL4, 4 }, -- { P_GPLL6, 5 }, --}; -- --static const char * const gcc_xo_gpll0_out_main_div2[] = { -- "xo", -- "gpll0_out_main_div2", --}; -- --static const struct parent_map gcc_xo_gpll0_out_main_div2_map[] = { -- { P_XO, 0 }, -- { P_GPLL0_DIV2, 1 }, --}; -- --static const char * const gcc_xo_bias_gpll0_gpll4_nss_ubi32[] = { -- "xo", -- "bias_pll_cc_clk", -- "gpll0", -- "gpll4", -- "nss_crypto_pll", -- "ubi32_pll", --}; -- --static const struct parent_map gcc_xo_bias_gpll0_gpll4_nss_ubi32_map[] = { -- { P_XO, 0 }, -- { P_BIAS_PLL, 1 }, -- { P_GPLL0, 2 }, -- { P_GPLL4, 3 }, -- { P_NSS_CRYPTO_PLL, 4 }, -- { P_UBI32_PLL, 5 }, --}; -- --static const char * const gcc_xo_gpll0_gpll4[] = { -- "xo", -- "gpll0", -- "gpll4", --}; -- --static const struct parent_map gcc_xo_gpll0_gpll4_map[] = { -- { P_XO, 0 }, -- { P_GPLL0, 1 }, -- { P_GPLL4, 2 }, --}; -- --static const char * const gcc_xo_uniphy0_rx_tx_ubi32_bias[] = { -- "xo", -- "uniphy0_gcc_rx_clk", -- "uniphy0_gcc_tx_clk", -- "ubi32_pll", -- "bias_pll_cc_clk", --}; -- --static const struct parent_map gcc_xo_uniphy0_rx_tx_ubi32_bias_map[] = { -- { P_XO, 0 }, -- { P_UNIPHY0_RX, 1 }, -- { P_UNIPHY0_TX, 2 }, -- { P_UBI32_PLL, 5 }, -- { P_BIAS_PLL, 6 }, --}; -- --static const char * const gcc_xo_uniphy0_tx_rx_ubi32_bias[] = { -- "xo", -- "uniphy0_gcc_tx_clk", -- "uniphy0_gcc_rx_clk", -- "ubi32_pll", -- "bias_pll_cc_clk", --}; -- --static const struct parent_map gcc_xo_uniphy0_tx_rx_ubi32_bias_map[] = { -- { P_XO, 0 }, -- { P_UNIPHY0_TX, 1 }, -- { P_UNIPHY0_RX, 2 }, -- { P_UBI32_PLL, 5 }, -- { P_BIAS_PLL, 6 }, --}; -- --static const char * const gcc_xo_uniphy0_rx_tx_uniphy1_rx_tx_ubi32_bias[] = { -- "xo", -- "uniphy0_gcc_rx_clk", -- "uniphy0_gcc_tx_clk", -- "uniphy1_gcc_rx_clk", -- "uniphy1_gcc_tx_clk", -- "ubi32_pll", -- "bias_pll_cc_clk", --}; -- --static const struct parent_map --gcc_xo_uniphy0_rx_tx_uniphy1_rx_tx_ubi32_bias_map[] = { -- { P_XO, 0 }, -- { P_UNIPHY0_RX, 1 }, -- { P_UNIPHY0_TX, 2 }, -- { P_UNIPHY1_RX, 3 }, -- { P_UNIPHY1_TX, 4 }, -- { P_UBI32_PLL, 5 }, -- { P_BIAS_PLL, 6 }, --}; -- --static const char * const gcc_xo_uniphy0_tx_rx_uniphy1_tx_rx_ubi32_bias[] = { -- "xo", -- "uniphy0_gcc_tx_clk", -- "uniphy0_gcc_rx_clk", -- "uniphy1_gcc_tx_clk", -- "uniphy1_gcc_rx_clk", -- "ubi32_pll", -- "bias_pll_cc_clk", --}; -- --static const struct parent_map --gcc_xo_uniphy0_tx_rx_uniphy1_tx_rx_ubi32_bias_map[] = { -- { P_XO, 0 }, -- { P_UNIPHY0_TX, 1 }, -- { P_UNIPHY0_RX, 2 }, -- { P_UNIPHY1_TX, 3 }, -- { P_UNIPHY1_RX, 4 }, -- { P_UBI32_PLL, 5 }, -- { P_BIAS_PLL, 6 }, --}; -- --static const char * const gcc_xo_uniphy2_rx_tx_ubi32_bias[] = { -- "xo", -- "uniphy2_gcc_rx_clk", -- "uniphy2_gcc_tx_clk", -- "ubi32_pll", -- "bias_pll_cc_clk", --}; -- --static const struct parent_map gcc_xo_uniphy2_rx_tx_ubi32_bias_map[] = { -- { P_XO, 0 }, -- { P_UNIPHY2_RX, 1 }, -- { P_UNIPHY2_TX, 2 }, -- { P_UBI32_PLL, 5 }, -- { P_BIAS_PLL, 6 }, --}; -- --static const char * const gcc_xo_uniphy2_tx_rx_ubi32_bias[] = { -- "xo", -- "uniphy2_gcc_tx_clk", -- "uniphy2_gcc_rx_clk", -- "ubi32_pll", -- "bias_pll_cc_clk", --}; -- --static const struct parent_map gcc_xo_uniphy2_tx_rx_ubi32_bias_map[] = { -- { P_XO, 0 }, -- { P_UNIPHY2_TX, 1 }, -- { P_UNIPHY2_RX, 2 }, -- { P_UBI32_PLL, 5 }, -- { P_BIAS_PLL, 6 }, --}; -- --static const char * const gcc_xo_gpll0_gpll6_gpll0_sleep_clk[] = { -- "xo", -- "gpll0", -- "gpll6", -- "gpll0_out_main_div2", -- "sleep_clk", --}; -- --static const struct parent_map gcc_xo_gpll0_gpll6_gpll0_sleep_clk_map[] = { -- { P_XO, 0 }, -- { P_GPLL0, 1 }, -- { P_GPLL6, 2 }, -- { P_GPLL0_DIV2, 4 }, -- { P_SLEEP_CLK, 6 }, --}; -- - static struct clk_alpha_pll gpll0_main = { - .offset = 0x21000, - .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_DEFAULT], -@@ -400,8 +57,9 @@ static struct clk_alpha_pll gpll0_main = - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gpll0_main", -- .parent_names = (const char *[]){ -- "xo" -+ .parent_data = &(const struct clk_parent_data){ -+ .fw_name = "xo", -+ .name = "xo", - }, - .num_parents = 1, - .ops = &clk_alpha_pll_ops, -@@ -414,9 +72,8 @@ static struct clk_fixed_factor gpll0_out - .div = 2, - .hw.init = &(struct clk_init_data){ - .name = "gpll0_out_main_div2", -- .parent_names = (const char *[]){ -- "gpll0_main" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &gpll0_main.clkr.hw }, - .num_parents = 1, - .ops = &clk_fixed_factor_ops, - }, -@@ -428,9 +85,8 @@ static struct clk_alpha_pll_postdiv gpll - .width = 4, - .clkr.hw.init = &(struct clk_init_data){ - .name = "gpll0", -- .parent_names = (const char *[]){ -- "gpll0_main" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &gpll0_main.clkr.hw }, - .num_parents = 1, - .ops = &clk_alpha_pll_postdiv_ro_ops, - }, -@@ -444,8 +100,9 @@ static struct clk_alpha_pll gpll2_main = - .enable_mask = BIT(2), - .hw.init = &(struct clk_init_data){ - .name = "gpll2_main", -- .parent_names = (const char *[]){ -- "xo" -+ .parent_data = &(const struct clk_parent_data){ -+ .fw_name = "xo", -+ .name = "xo", - }, - .num_parents = 1, - .ops = &clk_alpha_pll_ops, -@@ -460,9 +117,8 @@ static struct clk_alpha_pll_postdiv gpll - .width = 4, - .clkr.hw.init = &(struct clk_init_data){ - .name = "gpll2", -- .parent_names = (const char *[]){ -- "gpll2_main" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &gpll2_main.clkr.hw }, - .num_parents = 1, - .ops = &clk_alpha_pll_postdiv_ro_ops, - }, -@@ -476,8 +132,9 @@ static struct clk_alpha_pll gpll4_main = - .enable_mask = BIT(5), - .hw.init = &(struct clk_init_data){ - .name = "gpll4_main", -- .parent_names = (const char *[]){ -- "xo" -+ .parent_data = &(const struct clk_parent_data){ -+ .fw_name = "xo", -+ .name = "xo", - }, - .num_parents = 1, - .ops = &clk_alpha_pll_ops, -@@ -492,9 +149,8 @@ static struct clk_alpha_pll_postdiv gpll - .width = 4, - .clkr.hw.init = &(struct clk_init_data){ - .name = "gpll4", -- .parent_names = (const char *[]){ -- "gpll4_main" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &gpll4_main.clkr.hw }, - .num_parents = 1, - .ops = &clk_alpha_pll_postdiv_ro_ops, - }, -@@ -509,8 +165,9 @@ static struct clk_alpha_pll gpll6_main = - .enable_mask = BIT(7), - .hw.init = &(struct clk_init_data){ - .name = "gpll6_main", -- .parent_names = (const char *[]){ -- "xo" -+ .parent_data = &(const struct clk_parent_data){ -+ .fw_name = "xo", -+ .name = "xo", - }, - .num_parents = 1, - .ops = &clk_alpha_pll_ops, -@@ -525,9 +182,8 @@ static struct clk_alpha_pll_postdiv gpll - .width = 2, - .clkr.hw.init = &(struct clk_init_data){ - .name = "gpll6", -- .parent_names = (const char *[]){ -- "gpll6_main" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &gpll6_main.clkr.hw }, - .num_parents = 1, - .ops = &clk_alpha_pll_postdiv_ro_ops, - }, -@@ -538,9 +194,8 @@ static struct clk_fixed_factor gpll6_out - .div = 2, - .hw.init = &(struct clk_init_data){ - .name = "gpll6_out_main_div2", -- .parent_names = (const char *[]){ -- "gpll6_main" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &gpll6_main.clkr.hw }, - .num_parents = 1, - .ops = &clk_fixed_factor_ops, - }, -@@ -555,8 +210,9 @@ static struct clk_alpha_pll ubi32_pll_ma - .enable_mask = BIT(6), - .hw.init = &(struct clk_init_data){ - .name = "ubi32_pll_main", -- .parent_names = (const char *[]){ -- "xo" -+ .parent_data = &(const struct clk_parent_data){ -+ .fw_name = "xo", -+ .name = "xo", - }, - .num_parents = 1, - .ops = &clk_alpha_pll_huayra_ops, -@@ -570,9 +226,8 @@ static struct clk_alpha_pll_postdiv ubi3 - .width = 2, - .clkr.hw.init = &(struct clk_init_data){ - .name = "ubi32_pll", -- .parent_names = (const char *[]){ -- "ubi32_pll_main" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &ubi32_pll_main.clkr.hw }, - .num_parents = 1, - .ops = &clk_alpha_pll_postdiv_ro_ops, - .flags = CLK_SET_RATE_PARENT, -@@ -587,8 +242,9 @@ static struct clk_alpha_pll nss_crypto_p - .enable_mask = BIT(4), - .hw.init = &(struct clk_init_data){ - .name = "nss_crypto_pll_main", -- .parent_names = (const char *[]){ -- "xo" -+ .parent_data = &(const struct clk_parent_data){ -+ .fw_name = "xo", -+ .name = "xo", - }, - .num_parents = 1, - .ops = &clk_alpha_pll_ops, -@@ -602,9 +258,8 @@ static struct clk_alpha_pll_postdiv nss_ - .width = 4, - .clkr.hw.init = &(struct clk_init_data){ - .name = "nss_crypto_pll", -- .parent_names = (const char *[]){ -- "nss_crypto_pll_main" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_crypto_pll_main.clkr.hw }, - .num_parents = 1, - .ops = &clk_alpha_pll_postdiv_ro_ops, - }, -@@ -617,6 +272,18 @@ static const struct freq_tbl ftbl_pcnoc_ - { } - }; - -+static const struct clk_parent_data gcc_xo_gpll0_gpll0_out_main_div2[] = { -+ { .fw_name = "xo", .name = "xo" }, -+ { .hw = &gpll0.clkr.hw}, -+ { .hw = &gpll0_out_main_div2.hw}, -+}; -+ -+static const struct parent_map gcc_xo_gpll0_gpll0_out_main_div2_map[] = { -+ { P_XO, 0 }, -+ { P_GPLL0, 1 }, -+ { P_GPLL0_DIV2, 4 }, -+}; -+ - static struct clk_rcg2 pcnoc_bfdcd_clk_src = { - .cmd_rcgr = 0x27000, - .freq_tbl = ftbl_pcnoc_bfdcd_clk_src, -@@ -624,8 +291,8 @@ static struct clk_rcg2 pcnoc_bfdcd_clk_s - .parent_map = gcc_xo_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "pcnoc_bfdcd_clk_src", -- .parent_names = gcc_xo_gpll0_gpll0_out_main_div2, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - .flags = CLK_IS_CRITICAL, - }, -@@ -636,9 +303,8 @@ static struct clk_fixed_factor pcnoc_clk - .div = 1, - .hw.init = &(struct clk_init_data){ - .name = "pcnoc_clk_src", -- .parent_names = (const char *[]){ -- "pcnoc_bfdcd_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcnoc_bfdcd_clk_src.clkr.hw }, - .num_parents = 1, - .ops = &clk_fixed_factor_ops, - .flags = CLK_SET_RATE_PARENT, -@@ -652,8 +318,9 @@ static struct clk_branch gcc_sleep_clk_s - .enable_mask = BIT(1), - .hw.init = &(struct clk_init_data){ - .name = "gcc_sleep_clk_src", -- .parent_names = (const char *[]){ -- "sleep_clk" -+ .parent_data = &(const struct clk_parent_data){ -+ .fw_name = "sleep_clk", -+ .name = "sleep_clk", - }, - .num_parents = 1, - .ops = &clk_branch2_ops, -@@ -676,8 +343,8 @@ static struct clk_rcg2 blsp1_qup1_i2c_ap - .parent_map = gcc_xo_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "blsp1_qup1_i2c_apps_clk_src", -- .parent_names = gcc_xo_gpll0_gpll0_out_main_div2, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -702,8 +369,8 @@ static struct clk_rcg2 blsp1_qup1_spi_ap - .parent_map = gcc_xo_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "blsp1_qup1_spi_apps_clk_src", -- .parent_names = gcc_xo_gpll0_gpll0_out_main_div2, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -715,8 +382,8 @@ static struct clk_rcg2 blsp1_qup2_i2c_ap - .parent_map = gcc_xo_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "blsp1_qup2_i2c_apps_clk_src", -- .parent_names = gcc_xo_gpll0_gpll0_out_main_div2, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -729,8 +396,8 @@ static struct clk_rcg2 blsp1_qup2_spi_ap - .parent_map = gcc_xo_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "blsp1_qup2_spi_apps_clk_src", -- .parent_names = gcc_xo_gpll0_gpll0_out_main_div2, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -742,8 +409,8 @@ static struct clk_rcg2 blsp1_qup3_i2c_ap - .parent_map = gcc_xo_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "blsp1_qup3_i2c_apps_clk_src", -- .parent_names = gcc_xo_gpll0_gpll0_out_main_div2, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -756,8 +423,8 @@ static struct clk_rcg2 blsp1_qup3_spi_ap - .parent_map = gcc_xo_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "blsp1_qup3_spi_apps_clk_src", -- .parent_names = gcc_xo_gpll0_gpll0_out_main_div2, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -769,8 +436,8 @@ static struct clk_rcg2 blsp1_qup4_i2c_ap - .parent_map = gcc_xo_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "blsp1_qup4_i2c_apps_clk_src", -- .parent_names = gcc_xo_gpll0_gpll0_out_main_div2, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -783,8 +450,8 @@ static struct clk_rcg2 blsp1_qup4_spi_ap - .parent_map = gcc_xo_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "blsp1_qup4_spi_apps_clk_src", -- .parent_names = gcc_xo_gpll0_gpll0_out_main_div2, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -796,8 +463,8 @@ static struct clk_rcg2 blsp1_qup5_i2c_ap - .parent_map = gcc_xo_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "blsp1_qup5_i2c_apps_clk_src", -- .parent_names = gcc_xo_gpll0_gpll0_out_main_div2, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -810,8 +477,8 @@ static struct clk_rcg2 blsp1_qup5_spi_ap - .parent_map = gcc_xo_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "blsp1_qup5_spi_apps_clk_src", -- .parent_names = gcc_xo_gpll0_gpll0_out_main_div2, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -823,8 +490,8 @@ static struct clk_rcg2 blsp1_qup6_i2c_ap - .parent_map = gcc_xo_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "blsp1_qup6_i2c_apps_clk_src", -- .parent_names = gcc_xo_gpll0_gpll0_out_main_div2, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -837,8 +504,8 @@ static struct clk_rcg2 blsp1_qup6_spi_ap - .parent_map = gcc_xo_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "blsp1_qup6_spi_apps_clk_src", -- .parent_names = gcc_xo_gpll0_gpll0_out_main_div2, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -871,8 +538,8 @@ static struct clk_rcg2 blsp1_uart1_apps_ - .parent_map = gcc_xo_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "blsp1_uart1_apps_clk_src", -- .parent_names = gcc_xo_gpll0_gpll0_out_main_div2, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -885,8 +552,8 @@ static struct clk_rcg2 blsp1_uart2_apps_ - .parent_map = gcc_xo_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "blsp1_uart2_apps_clk_src", -- .parent_names = gcc_xo_gpll0_gpll0_out_main_div2, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -899,8 +566,8 @@ static struct clk_rcg2 blsp1_uart3_apps_ - .parent_map = gcc_xo_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "blsp1_uart3_apps_clk_src", -- .parent_names = gcc_xo_gpll0_gpll0_out_main_div2, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -913,8 +580,8 @@ static struct clk_rcg2 blsp1_uart4_apps_ - .parent_map = gcc_xo_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "blsp1_uart4_apps_clk_src", -- .parent_names = gcc_xo_gpll0_gpll0_out_main_div2, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -927,8 +594,8 @@ static struct clk_rcg2 blsp1_uart5_apps_ - .parent_map = gcc_xo_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "blsp1_uart5_apps_clk_src", -- .parent_names = gcc_xo_gpll0_gpll0_out_main_div2, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -941,8 +608,8 @@ static struct clk_rcg2 blsp1_uart6_apps_ - .parent_map = gcc_xo_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "blsp1_uart6_apps_clk_src", -- .parent_names = gcc_xo_gpll0_gpll0_out_main_div2, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -952,6 +619,11 @@ static const struct clk_parent_data gcc_ - { .hw = &gpll0.clkr.hw }, - }; - -+static const struct parent_map gcc_xo_gpll0_map[] = { -+ { P_XO, 0 }, -+ { P_GPLL0, 1 }, -+}; -+ - static const struct freq_tbl ftbl_pcie_axi_clk_src[] = { - F(19200000, P_XO, 1, 0, 0), - F(200000000, P_GPLL0, 4, 0, 0), -@@ -966,7 +638,7 @@ static struct clk_rcg2 pcie0_axi_clk_src - .clkr.hw.init = &(struct clk_init_data){ - .name = "pcie0_axi_clk_src", - .parent_data = gcc_xo_gpll0, -- .num_parents = 2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0), - .ops = &clk_rcg2_ops, - }, - }; -@@ -975,6 +647,18 @@ static const struct freq_tbl ftbl_pcie_a - F(19200000, P_XO, 1, 0, 0), - }; - -+static const struct clk_parent_data gcc_xo_gpll0_sleep_clk[] = { -+ { .fw_name = "xo", .name = "xo" }, -+ { .hw = &gpll0.clkr.hw }, -+ { .fw_name = "sleep_clk", .name = "sleep_clk" }, -+}; -+ -+static const struct parent_map gcc_xo_gpll0_sleep_clk_map[] = { -+ { P_XO, 0 }, -+ { P_GPLL0, 2 }, -+ { P_SLEEP_CLK, 6 }, -+}; -+ - static struct clk_rcg2 pcie0_aux_clk_src = { - .cmd_rcgr = 0x75024, - .freq_tbl = ftbl_pcie_aux_clk_src, -@@ -983,12 +667,22 @@ static struct clk_rcg2 pcie0_aux_clk_src - .parent_map = gcc_xo_gpll0_sleep_clk_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "pcie0_aux_clk_src", -- .parent_names = gcc_xo_gpll0_sleep_clk, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_sleep_clk, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_sleep_clk), - .ops = &clk_rcg2_ops, - }, - }; - -+static const struct clk_parent_data gcc_pcie20_phy0_pipe_clk_xo[] = { -+ { .name = "pcie20_phy0_pipe_clk" }, -+ { .fw_name = "xo", .name = "xo" }, -+}; -+ -+static const struct parent_map gcc_pcie20_phy0_pipe_clk_xo_map[] = { -+ { P_PCIE20_PHY0_PIPE, 0 }, -+ { P_XO, 2 }, -+}; -+ - static struct clk_regmap_mux pcie0_pipe_clk_src = { - .reg = 0x7501c, - .shift = 8, -@@ -997,8 +691,8 @@ static struct clk_regmap_mux pcie0_pipe_ - .clkr = { - .hw.init = &(struct clk_init_data){ - .name = "pcie0_pipe_clk_src", -- .parent_names = gcc_pcie20_phy0_pipe_clk_xo, -- .num_parents = 2, -+ .parent_data = gcc_pcie20_phy0_pipe_clk_xo, -+ .num_parents = ARRAY_SIZE(gcc_pcie20_phy0_pipe_clk_xo), - .ops = &clk_regmap_mux_closest_ops, - .flags = CLK_SET_RATE_PARENT, - }, -@@ -1013,7 +707,7 @@ static struct clk_rcg2 pcie1_axi_clk_src - .clkr.hw.init = &(struct clk_init_data){ - .name = "pcie1_axi_clk_src", - .parent_data = gcc_xo_gpll0, -- .num_parents = 2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1026,12 +720,22 @@ static struct clk_rcg2 pcie1_aux_clk_src - .parent_map = gcc_xo_gpll0_sleep_clk_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "pcie1_aux_clk_src", -- .parent_names = gcc_xo_gpll0_sleep_clk, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_sleep_clk, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_sleep_clk), - .ops = &clk_rcg2_ops, - }, - }; - -+static const struct clk_parent_data gcc_pcie20_phy1_pipe_clk_xo[] = { -+ { .name = "pcie20_phy1_pipe_clk" }, -+ { .fw_name = "xo", .name = "xo" }, -+}; -+ -+static const struct parent_map gcc_pcie20_phy1_pipe_clk_xo_map[] = { -+ { P_PCIE20_PHY1_PIPE, 0 }, -+ { P_XO, 2 }, -+}; -+ - static struct clk_regmap_mux pcie1_pipe_clk_src = { - .reg = 0x7601c, - .shift = 8, -@@ -1040,8 +744,8 @@ static struct clk_regmap_mux pcie1_pipe_ - .clkr = { - .hw.init = &(struct clk_init_data){ - .name = "pcie1_pipe_clk_src", -- .parent_names = gcc_pcie20_phy1_pipe_clk_xo, -- .num_parents = 2, -+ .parent_data = gcc_pcie20_phy1_pipe_clk_xo, -+ .num_parents = ARRAY_SIZE(gcc_pcie20_phy1_pipe_clk_xo), - .ops = &clk_regmap_mux_closest_ops, - .flags = CLK_SET_RATE_PARENT, - }, -@@ -1060,6 +764,20 @@ static const struct freq_tbl ftbl_sdcc_a - { } - }; - -+static const struct clk_parent_data gcc_xo_gpll0_gpll2_gpll0_out_main_div2[] = { -+ { .fw_name = "xo", .name = "xo" }, -+ { .hw = &gpll0.clkr.hw }, -+ { .hw = &gpll2.clkr.hw }, -+ { .hw = &gpll0_out_main_div2.hw }, -+}; -+ -+static const struct parent_map gcc_xo_gpll0_gpll2_gpll0_out_main_div2_map[] = { -+ { P_XO, 0 }, -+ { P_GPLL0, 1 }, -+ { P_GPLL2, 2 }, -+ { P_GPLL0_DIV2, 4 }, -+}; -+ - static struct clk_rcg2 sdcc1_apps_clk_src = { - .cmd_rcgr = 0x42004, - .freq_tbl = ftbl_sdcc_apps_clk_src, -@@ -1068,8 +786,8 @@ static struct clk_rcg2 sdcc1_apps_clk_sr - .parent_map = gcc_xo_gpll0_gpll2_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "sdcc1_apps_clk_src", -- .parent_names = gcc_xo_gpll0_gpll2_gpll0_out_main_div2, -- .num_parents = 4, -+ .parent_data = gcc_xo_gpll0_gpll2_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll2_gpll0_out_main_div2), - .ops = &clk_rcg2_floor_ops, - }, - }; -@@ -1080,6 +798,20 @@ static const struct freq_tbl ftbl_sdcc_i - F(308570000, P_GPLL6, 3.5, 0, 0), - }; - -+static const struct clk_parent_data gcc_xo_gpll0_gpll6_gpll0_div2[] = { -+ { .fw_name = "xo", .name = "xo" }, -+ { .hw = &gpll0.clkr.hw }, -+ { .hw = &gpll6.clkr.hw }, -+ { .hw = &gpll0_out_main_div2.hw }, -+}; -+ -+static const struct parent_map gcc_xo_gpll0_gpll6_gpll0_div2_map[] = { -+ { P_XO, 0 }, -+ { P_GPLL0, 1 }, -+ { P_GPLL6, 2 }, -+ { P_GPLL0_DIV2, 4 }, -+}; -+ - static struct clk_rcg2 sdcc1_ice_core_clk_src = { - .cmd_rcgr = 0x5d000, - .freq_tbl = ftbl_sdcc_ice_core_clk_src, -@@ -1088,8 +820,8 @@ static struct clk_rcg2 sdcc1_ice_core_cl - .parent_map = gcc_xo_gpll0_gpll6_gpll0_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "sdcc1_ice_core_clk_src", -- .parent_names = gcc_xo_gpll0_gpll6_gpll0_div2, -- .num_parents = 4, -+ .parent_data = gcc_xo_gpll0_gpll6_gpll0_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll6_gpll0_div2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1102,8 +834,8 @@ static struct clk_rcg2 sdcc2_apps_clk_sr - .parent_map = gcc_xo_gpll0_gpll2_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "sdcc2_apps_clk_src", -- .parent_names = gcc_xo_gpll0_gpll2_gpll0_out_main_div2, -- .num_parents = 4, -+ .parent_data = gcc_xo_gpll0_gpll2_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll2_gpll0_out_main_div2), - .ops = &clk_rcg2_floor_ops, - }, - }; -@@ -1115,6 +847,18 @@ static const struct freq_tbl ftbl_usb_ma - { } - }; - -+static const struct clk_parent_data gcc_xo_gpll0_out_main_div2_gpll0[] = { -+ { .fw_name = "xo", .name = "xo" }, -+ { .hw = &gpll0_out_main_div2.hw }, -+ { .hw = &gpll0.clkr.hw }, -+}; -+ -+static const struct parent_map gcc_xo_gpll0_out_main_div2_gpll0_map[] = { -+ { P_XO, 0 }, -+ { P_GPLL0_DIV2, 2 }, -+ { P_GPLL0, 1 }, -+}; -+ - static struct clk_rcg2 usb0_master_clk_src = { - .cmd_rcgr = 0x3e00c, - .freq_tbl = ftbl_usb_master_clk_src, -@@ -1123,8 +867,8 @@ static struct clk_rcg2 usb0_master_clk_s - .parent_map = gcc_xo_gpll0_out_main_div2_gpll0_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "usb0_master_clk_src", -- .parent_names = gcc_xo_gpll0_out_main_div2_gpll0, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_out_main_div2_gpll0, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_out_main_div2_gpll0), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1142,8 +886,8 @@ static struct clk_rcg2 usb0_aux_clk_src - .parent_map = gcc_xo_gpll0_sleep_clk_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "usb0_aux_clk_src", -- .parent_names = gcc_xo_gpll0_sleep_clk, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_sleep_clk, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_sleep_clk), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1155,6 +899,20 @@ static const struct freq_tbl ftbl_usb_mo - { } - }; - -+static const struct clk_parent_data gcc_xo_gpll6_gpll0_gpll0_out_main_div2[] = { -+ { .fw_name = "xo", .name = "xo" }, -+ { .hw = &gpll6.clkr.hw }, -+ { .hw = &gpll0.clkr.hw }, -+ { .hw = &gpll0_out_main_div2.hw }, -+}; -+ -+static const struct parent_map gcc_xo_gpll6_gpll0_gpll0_out_main_div2_map[] = { -+ { P_XO, 0 }, -+ { P_GPLL6, 1 }, -+ { P_GPLL0, 3 }, -+ { P_GPLL0_DIV2, 4 }, -+}; -+ - static struct clk_rcg2 usb0_mock_utmi_clk_src = { - .cmd_rcgr = 0x3e020, - .freq_tbl = ftbl_usb_mock_utmi_clk_src, -@@ -1163,12 +921,22 @@ static struct clk_rcg2 usb0_mock_utmi_cl - .parent_map = gcc_xo_gpll6_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "usb0_mock_utmi_clk_src", -- .parent_names = gcc_xo_gpll6_gpll0_gpll0_out_main_div2, -- .num_parents = 4, -+ .parent_data = gcc_xo_gpll6_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll6_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; - -+static const struct clk_parent_data gcc_usb3phy_0_cc_pipe_clk_xo[] = { -+ { .name = "usb3phy_0_cc_pipe_clk" }, -+ { .fw_name = "xo", .name = "xo" }, -+}; -+ -+static const struct parent_map gcc_usb3phy_0_cc_pipe_clk_xo_map[] = { -+ { P_USB3PHY_0_PIPE, 0 }, -+ { P_XO, 2 }, -+}; -+ - static struct clk_regmap_mux usb0_pipe_clk_src = { - .reg = 0x3e048, - .shift = 8, -@@ -1177,8 +945,8 @@ static struct clk_regmap_mux usb0_pipe_c - .clkr = { - .hw.init = &(struct clk_init_data){ - .name = "usb0_pipe_clk_src", -- .parent_names = gcc_usb3phy_0_cc_pipe_clk_xo, -- .num_parents = 2, -+ .parent_data = gcc_usb3phy_0_cc_pipe_clk_xo, -+ .num_parents = ARRAY_SIZE(gcc_usb3phy_0_cc_pipe_clk_xo), - .ops = &clk_regmap_mux_closest_ops, - .flags = CLK_SET_RATE_PARENT, - }, -@@ -1193,8 +961,8 @@ static struct clk_rcg2 usb1_master_clk_s - .parent_map = gcc_xo_gpll0_out_main_div2_gpll0_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "usb1_master_clk_src", -- .parent_names = gcc_xo_gpll0_out_main_div2_gpll0, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_out_main_div2_gpll0, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_out_main_div2_gpll0), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1207,8 +975,8 @@ static struct clk_rcg2 usb1_aux_clk_src - .parent_map = gcc_xo_gpll0_sleep_clk_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "usb1_aux_clk_src", -- .parent_names = gcc_xo_gpll0_sleep_clk, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_sleep_clk, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_sleep_clk), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1221,12 +989,22 @@ static struct clk_rcg2 usb1_mock_utmi_cl - .parent_map = gcc_xo_gpll6_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "usb1_mock_utmi_clk_src", -- .parent_names = gcc_xo_gpll6_gpll0_gpll0_out_main_div2, -- .num_parents = 4, -+ .parent_data = gcc_xo_gpll6_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll6_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; - -+static const struct clk_parent_data gcc_usb3phy_1_cc_pipe_clk_xo[] = { -+ { .name = "usb3phy_1_cc_pipe_clk" }, -+ { .fw_name = "xo", .name = "xo" }, -+}; -+ -+static const struct parent_map gcc_usb3phy_1_cc_pipe_clk_xo_map[] = { -+ { P_USB3PHY_1_PIPE, 0 }, -+ { P_XO, 2 }, -+}; -+ - static struct clk_regmap_mux usb1_pipe_clk_src = { - .reg = 0x3f048, - .shift = 8, -@@ -1235,8 +1013,8 @@ static struct clk_regmap_mux usb1_pipe_c - .clkr = { - .hw.init = &(struct clk_init_data){ - .name = "usb1_pipe_clk_src", -- .parent_names = gcc_usb3phy_1_cc_pipe_clk_xo, -- .num_parents = 2, -+ .parent_data = gcc_usb3phy_1_cc_pipe_clk_xo, -+ .num_parents = ARRAY_SIZE(gcc_usb3phy_1_cc_pipe_clk_xo), - .ops = &clk_regmap_mux_closest_ops, - .flags = CLK_SET_RATE_PARENT, - }, -@@ -1250,8 +1028,9 @@ static struct clk_branch gcc_xo_clk_src - .enable_mask = BIT(1), - .hw.init = &(struct clk_init_data){ - .name = "gcc_xo_clk_src", -- .parent_names = (const char *[]){ -- "xo" -+ .parent_data = &(const struct clk_parent_data){ -+ .fw_name = "xo", -+ .name = "xo", - }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT | CLK_IS_CRITICAL, -@@ -1265,9 +1044,8 @@ static struct clk_fixed_factor gcc_xo_di - .div = 4, - .hw.init = &(struct clk_init_data){ - .name = "gcc_xo_div4_clk_src", -- .parent_names = (const char *[]){ -- "gcc_xo_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &gcc_xo_clk_src.clkr.hw }, - .num_parents = 1, - .ops = &clk_fixed_factor_ops, - .flags = CLK_SET_RATE_PARENT, -@@ -1285,6 +1063,20 @@ static const struct freq_tbl ftbl_system - { } - }; - -+static const struct clk_parent_data gcc_xo_gpll0_gpll6_gpll0_out_main_div2[] = { -+ { .fw_name = "xo", .name = "xo" }, -+ { .hw = &gpll0.clkr.hw }, -+ { .hw = &gpll6.clkr.hw }, -+ { .hw = &gpll0_out_main_div2.hw }, -+}; -+ -+static const struct parent_map gcc_xo_gpll0_gpll6_gpll0_out_main_div2_map[] = { -+ { P_XO, 0 }, -+ { P_GPLL0, 1 }, -+ { P_GPLL6, 2 }, -+ { P_GPLL0_DIV2, 3 }, -+}; -+ - static struct clk_rcg2 system_noc_bfdcd_clk_src = { - .cmd_rcgr = 0x26004, - .freq_tbl = ftbl_system_noc_bfdcd_clk_src, -@@ -1292,8 +1084,8 @@ static struct clk_rcg2 system_noc_bfdcd_ - .parent_map = gcc_xo_gpll0_gpll6_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "system_noc_bfdcd_clk_src", -- .parent_names = gcc_xo_gpll0_gpll6_gpll0_out_main_div2, -- .num_parents = 4, -+ .parent_data = gcc_xo_gpll0_gpll6_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll6_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - .flags = CLK_IS_CRITICAL, - }, -@@ -1304,9 +1096,8 @@ static struct clk_fixed_factor system_no - .div = 1, - .hw.init = &(struct clk_init_data){ - .name = "system_noc_clk_src", -- .parent_names = (const char *[]){ -- "system_noc_bfdcd_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &system_noc_bfdcd_clk_src.clkr.hw }, - .num_parents = 1, - .ops = &clk_fixed_factor_ops, - .flags = CLK_SET_RATE_PARENT, -@@ -1327,7 +1118,7 @@ static struct clk_rcg2 nss_ce_clk_src = - .clkr.hw.init = &(struct clk_init_data){ - .name = "nss_ce_clk_src", - .parent_data = gcc_xo_gpll0, -- .num_parents = 2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1338,6 +1129,20 @@ static const struct freq_tbl ftbl_nss_no - { } - }; - -+static const struct clk_parent_data gcc_xo_bias_pll_nss_noc_clk_gpll0_gpll2[] = { -+ { .fw_name = "xo", .name = "xo" }, -+ { .name = "bias_pll_nss_noc_clk" }, -+ { .hw = &gpll0.clkr.hw }, -+ { .hw = &gpll2.clkr.hw }, -+}; -+ -+static const struct parent_map gcc_xo_bias_pll_nss_noc_clk_gpll0_gpll2_map[] = { -+ { P_XO, 0 }, -+ { P_BIAS_PLL_NSS_NOC, 1 }, -+ { P_GPLL0, 2 }, -+ { P_GPLL2, 3 }, -+}; -+ - static struct clk_rcg2 nss_noc_bfdcd_clk_src = { - .cmd_rcgr = 0x68088, - .freq_tbl = ftbl_nss_noc_bfdcd_clk_src, -@@ -1345,8 +1150,8 @@ static struct clk_rcg2 nss_noc_bfdcd_clk - .parent_map = gcc_xo_bias_pll_nss_noc_clk_gpll0_gpll2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "nss_noc_bfdcd_clk_src", -- .parent_names = gcc_xo_bias_pll_nss_noc_clk_gpll0_gpll2, -- .num_parents = 4, -+ .parent_data = gcc_xo_bias_pll_nss_noc_clk_gpll0_gpll2, -+ .num_parents = ARRAY_SIZE(gcc_xo_bias_pll_nss_noc_clk_gpll0_gpll2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1356,9 +1161,8 @@ static struct clk_fixed_factor nss_noc_c - .div = 1, - .hw.init = &(struct clk_init_data){ - .name = "nss_noc_clk_src", -- .parent_names = (const char *[]){ -- "nss_noc_bfdcd_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_noc_bfdcd_clk_src.clkr.hw }, - .num_parents = 1, - .ops = &clk_fixed_factor_ops, - .flags = CLK_SET_RATE_PARENT, -@@ -1371,6 +1175,18 @@ static const struct freq_tbl ftbl_nss_cr - { } - }; - -+static const struct clk_parent_data gcc_xo_nss_crypto_pll_gpll0[] = { -+ { .fw_name = "xo", .name = "xo" }, -+ { .hw = &nss_crypto_pll.clkr.hw }, -+ { .hw = &gpll0.clkr.hw }, -+}; -+ -+static const struct parent_map gcc_xo_nss_crypto_pll_gpll0_map[] = { -+ { P_XO, 0 }, -+ { P_NSS_CRYPTO_PLL, 1 }, -+ { P_GPLL0, 2 }, -+}; -+ - static struct clk_rcg2 nss_crypto_clk_src = { - .cmd_rcgr = 0x68144, - .freq_tbl = ftbl_nss_crypto_clk_src, -@@ -1379,8 +1195,8 @@ static struct clk_rcg2 nss_crypto_clk_sr - .parent_map = gcc_xo_nss_crypto_pll_gpll0_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "nss_crypto_clk_src", -- .parent_names = gcc_xo_nss_crypto_pll_gpll0, -- .num_parents = 3, -+ .parent_data = gcc_xo_nss_crypto_pll_gpll0, -+ .num_parents = ARRAY_SIZE(gcc_xo_nss_crypto_pll_gpll0), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1394,6 +1210,24 @@ static const struct freq_tbl ftbl_nss_ub - { } - }; - -+static const struct clk_parent_data gcc_xo_ubi32_pll_gpll0_gpll2_gpll4_gpll6[] = { -+ { .fw_name = "xo", .name = "xo" }, -+ { .hw = &ubi32_pll.clkr.hw }, -+ { .hw = &gpll0.clkr.hw }, -+ { .hw = &gpll2.clkr.hw }, -+ { .hw = &gpll4.clkr.hw }, -+ { .hw = &gpll6.clkr.hw }, -+}; -+ -+static const struct parent_map gcc_xo_ubi32_gpll0_gpll2_gpll4_gpll6_map[] = { -+ { P_XO, 0 }, -+ { P_UBI32_PLL, 1 }, -+ { P_GPLL0, 2 }, -+ { P_GPLL2, 3 }, -+ { P_GPLL4, 4 }, -+ { P_GPLL6, 5 }, -+}; -+ - static struct clk_rcg2 nss_ubi0_clk_src = { - .cmd_rcgr = 0x68104, - .freq_tbl = ftbl_nss_ubi_clk_src, -@@ -1401,8 +1235,8 @@ static struct clk_rcg2 nss_ubi0_clk_src - .parent_map = gcc_xo_ubi32_gpll0_gpll2_gpll4_gpll6_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "nss_ubi0_clk_src", -- .parent_names = gcc_xo_ubi32_pll_gpll0_gpll2_gpll4_gpll6, -- .num_parents = 6, -+ .parent_data = gcc_xo_ubi32_pll_gpll0_gpll2_gpll4_gpll6, -+ .num_parents = ARRAY_SIZE(gcc_xo_ubi32_pll_gpll0_gpll2_gpll4_gpll6), - .ops = &clk_rcg2_ops, - .flags = CLK_SET_RATE_PARENT, - }, -@@ -1415,9 +1249,8 @@ static struct clk_regmap_div nss_ubi0_di - .clkr = { - .hw.init = &(struct clk_init_data){ - .name = "nss_ubi0_div_clk_src", -- .parent_names = (const char *[]){ -- "nss_ubi0_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ubi0_clk_src.clkr.hw }, - .num_parents = 1, - .ops = &clk_regmap_div_ro_ops, - .flags = CLK_SET_RATE_PARENT, -@@ -1432,8 +1265,8 @@ static struct clk_rcg2 nss_ubi1_clk_src - .parent_map = gcc_xo_ubi32_gpll0_gpll2_gpll4_gpll6_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "nss_ubi1_clk_src", -- .parent_names = gcc_xo_ubi32_pll_gpll0_gpll2_gpll4_gpll6, -- .num_parents = 6, -+ .parent_data = gcc_xo_ubi32_pll_gpll0_gpll2_gpll4_gpll6, -+ .num_parents = ARRAY_SIZE(gcc_xo_ubi32_pll_gpll0_gpll2_gpll4_gpll6), - .ops = &clk_rcg2_ops, - .flags = CLK_SET_RATE_PARENT, - }, -@@ -1446,9 +1279,8 @@ static struct clk_regmap_div nss_ubi1_di - .clkr = { - .hw.init = &(struct clk_init_data){ - .name = "nss_ubi1_div_clk_src", -- .parent_names = (const char *[]){ -- "nss_ubi1_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ubi1_clk_src.clkr.hw }, - .num_parents = 1, - .ops = &clk_regmap_div_ro_ops, - .flags = CLK_SET_RATE_PARENT, -@@ -1462,6 +1294,16 @@ static const struct freq_tbl ftbl_ubi_mp - { } - }; - -+static const struct clk_parent_data gcc_xo_gpll0_out_main_div2[] = { -+ { .fw_name = "xo", .name = "xo" }, -+ { .hw = &gpll0_out_main_div2.hw }, -+}; -+ -+static const struct parent_map gcc_xo_gpll0_out_main_div2_map[] = { -+ { P_XO, 0 }, -+ { P_GPLL0_DIV2, 1 }, -+}; -+ - static struct clk_rcg2 ubi_mpt_clk_src = { - .cmd_rcgr = 0x68090, - .freq_tbl = ftbl_ubi_mpt_clk_src, -@@ -1469,8 +1311,8 @@ static struct clk_rcg2 ubi_mpt_clk_src = - .parent_map = gcc_xo_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "ubi_mpt_clk_src", -- .parent_names = gcc_xo_gpll0_out_main_div2, -- .num_parents = 2, -+ .parent_data = gcc_xo_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1481,6 +1323,18 @@ static const struct freq_tbl ftbl_nss_im - { } - }; - -+static const struct clk_parent_data gcc_xo_gpll0_gpll4[] = { -+ { .fw_name = "xo", .name = "xo" }, -+ { .hw = &gpll0.clkr.hw }, -+ { .hw = &gpll4.clkr.hw }, -+}; -+ -+static const struct parent_map gcc_xo_gpll0_gpll4_map[] = { -+ { P_XO, 0 }, -+ { P_GPLL0, 1 }, -+ { P_GPLL4, 2 }, -+}; -+ - static struct clk_rcg2 nss_imem_clk_src = { - .cmd_rcgr = 0x68158, - .freq_tbl = ftbl_nss_imem_clk_src, -@@ -1488,8 +1342,8 @@ static struct clk_rcg2 nss_imem_clk_src - .parent_map = gcc_xo_gpll0_gpll4_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "nss_imem_clk_src", -- .parent_names = gcc_xo_gpll0_gpll4, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_gpll4, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll4), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1500,6 +1354,24 @@ static const struct freq_tbl ftbl_nss_pp - { } - }; - -+static const struct clk_parent_data gcc_xo_bias_gpll0_gpll4_nss_ubi32[] = { -+ { .fw_name = "xo", .name = "xo" }, -+ { .name = "bias_pll_cc_clk" }, -+ { .hw = &gpll0.clkr.hw }, -+ { .hw = &gpll4.clkr.hw }, -+ { .hw = &nss_crypto_pll.clkr.hw }, -+ { .hw = &ubi32_pll.clkr.hw }, -+}; -+ -+static const struct parent_map gcc_xo_bias_gpll0_gpll4_nss_ubi32_map[] = { -+ { P_XO, 0 }, -+ { P_BIAS_PLL, 1 }, -+ { P_GPLL0, 2 }, -+ { P_GPLL4, 3 }, -+ { P_NSS_CRYPTO_PLL, 4 }, -+ { P_UBI32_PLL, 5 }, -+}; -+ - static struct clk_rcg2 nss_ppe_clk_src = { - .cmd_rcgr = 0x68080, - .freq_tbl = ftbl_nss_ppe_clk_src, -@@ -1507,8 +1379,8 @@ static struct clk_rcg2 nss_ppe_clk_src = - .parent_map = gcc_xo_bias_gpll0_gpll4_nss_ubi32_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "nss_ppe_clk_src", -- .parent_names = gcc_xo_bias_gpll0_gpll4_nss_ubi32, -- .num_parents = 6, -+ .parent_data = gcc_xo_bias_gpll0_gpll4_nss_ubi32, -+ .num_parents = ARRAY_SIZE(gcc_xo_bias_gpll0_gpll4_nss_ubi32), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1518,9 +1390,8 @@ static struct clk_fixed_factor nss_ppe_c - .div = 4, - .hw.init = &(struct clk_init_data){ - .name = "nss_ppe_cdiv_clk_src", -- .parent_names = (const char *[]){ -- "nss_ppe_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ppe_clk_src.clkr.hw }, - .num_parents = 1, - .ops = &clk_fixed_factor_ops, - .flags = CLK_SET_RATE_PARENT, -@@ -1534,6 +1405,22 @@ static const struct freq_tbl ftbl_nss_po - { } - }; - -+static const struct clk_parent_data gcc_xo_uniphy0_rx_tx_ubi32_bias[] = { -+ { .fw_name = "xo", .name = "xo" }, -+ { .name = "uniphy0_gcc_rx_clk" }, -+ { .name = "uniphy0_gcc_tx_clk" }, -+ { .hw = &ubi32_pll.clkr.hw }, -+ { .name = "bias_pll_cc_clk" }, -+}; -+ -+static const struct parent_map gcc_xo_uniphy0_rx_tx_ubi32_bias_map[] = { -+ { P_XO, 0 }, -+ { P_UNIPHY0_RX, 1 }, -+ { P_UNIPHY0_TX, 2 }, -+ { P_UBI32_PLL, 5 }, -+ { P_BIAS_PLL, 6 }, -+}; -+ - static struct clk_rcg2 nss_port1_rx_clk_src = { - .cmd_rcgr = 0x68020, - .freq_tbl = ftbl_nss_port1_rx_clk_src, -@@ -1541,8 +1428,8 @@ static struct clk_rcg2 nss_port1_rx_clk_ - .parent_map = gcc_xo_uniphy0_rx_tx_ubi32_bias_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "nss_port1_rx_clk_src", -- .parent_names = gcc_xo_uniphy0_rx_tx_ubi32_bias, -- .num_parents = 5, -+ .parent_data = gcc_xo_uniphy0_rx_tx_ubi32_bias, -+ .num_parents = ARRAY_SIZE(gcc_xo_uniphy0_rx_tx_ubi32_bias), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1554,9 +1441,8 @@ static struct clk_regmap_div nss_port1_r - .clkr = { - .hw.init = &(struct clk_init_data){ - .name = "nss_port1_rx_div_clk_src", -- .parent_names = (const char *[]){ -- "nss_port1_rx_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port1_rx_clk_src.clkr.hw }, - .num_parents = 1, - .ops = &clk_regmap_div_ops, - .flags = CLK_SET_RATE_PARENT, -@@ -1571,6 +1457,22 @@ static const struct freq_tbl ftbl_nss_po - { } - }; - -+static const struct clk_parent_data gcc_xo_uniphy0_tx_rx_ubi32_bias[] = { -+ { .fw_name = "xo", .name = "xo" }, -+ { .name = "uniphy0_gcc_tx_clk" }, -+ { .name = "uniphy0_gcc_rx_clk" }, -+ { .hw = &ubi32_pll.clkr.hw }, -+ { .name = "bias_pll_cc_clk" }, -+}; -+ -+static const struct parent_map gcc_xo_uniphy0_tx_rx_ubi32_bias_map[] = { -+ { P_XO, 0 }, -+ { P_UNIPHY0_TX, 1 }, -+ { P_UNIPHY0_RX, 2 }, -+ { P_UBI32_PLL, 5 }, -+ { P_BIAS_PLL, 6 }, -+}; -+ - static struct clk_rcg2 nss_port1_tx_clk_src = { - .cmd_rcgr = 0x68028, - .freq_tbl = ftbl_nss_port1_tx_clk_src, -@@ -1578,8 +1480,8 @@ static struct clk_rcg2 nss_port1_tx_clk_ - .parent_map = gcc_xo_uniphy0_tx_rx_ubi32_bias_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "nss_port1_tx_clk_src", -- .parent_names = gcc_xo_uniphy0_tx_rx_ubi32_bias, -- .num_parents = 5, -+ .parent_data = gcc_xo_uniphy0_tx_rx_ubi32_bias, -+ .num_parents = ARRAY_SIZE(gcc_xo_uniphy0_tx_rx_ubi32_bias), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1591,9 +1493,8 @@ static struct clk_regmap_div nss_port1_t - .clkr = { - .hw.init = &(struct clk_init_data){ - .name = "nss_port1_tx_div_clk_src", -- .parent_names = (const char *[]){ -- "nss_port1_tx_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port1_tx_clk_src.clkr.hw }, - .num_parents = 1, - .ops = &clk_regmap_div_ops, - .flags = CLK_SET_RATE_PARENT, -@@ -1608,8 +1509,8 @@ static struct clk_rcg2 nss_port2_rx_clk_ - .parent_map = gcc_xo_uniphy0_rx_tx_ubi32_bias_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "nss_port2_rx_clk_src", -- .parent_names = gcc_xo_uniphy0_rx_tx_ubi32_bias, -- .num_parents = 5, -+ .parent_data = gcc_xo_uniphy0_rx_tx_ubi32_bias, -+ .num_parents = ARRAY_SIZE(gcc_xo_uniphy0_rx_tx_ubi32_bias), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1621,9 +1522,8 @@ static struct clk_regmap_div nss_port2_r - .clkr = { - .hw.init = &(struct clk_init_data){ - .name = "nss_port2_rx_div_clk_src", -- .parent_names = (const char *[]){ -- "nss_port2_rx_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port2_rx_clk_src.clkr.hw }, - .num_parents = 1, - .ops = &clk_regmap_div_ops, - .flags = CLK_SET_RATE_PARENT, -@@ -1638,8 +1538,8 @@ static struct clk_rcg2 nss_port2_tx_clk_ - .parent_map = gcc_xo_uniphy0_tx_rx_ubi32_bias_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "nss_port2_tx_clk_src", -- .parent_names = gcc_xo_uniphy0_tx_rx_ubi32_bias, -- .num_parents = 5, -+ .parent_data = gcc_xo_uniphy0_tx_rx_ubi32_bias, -+ .num_parents = ARRAY_SIZE(gcc_xo_uniphy0_tx_rx_ubi32_bias), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1651,9 +1551,8 @@ static struct clk_regmap_div nss_port2_t - .clkr = { - .hw.init = &(struct clk_init_data){ - .name = "nss_port2_tx_div_clk_src", -- .parent_names = (const char *[]){ -- "nss_port2_tx_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port2_tx_clk_src.clkr.hw }, - .num_parents = 1, - .ops = &clk_regmap_div_ops, - .flags = CLK_SET_RATE_PARENT, -@@ -1668,8 +1567,8 @@ static struct clk_rcg2 nss_port3_rx_clk_ - .parent_map = gcc_xo_uniphy0_rx_tx_ubi32_bias_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "nss_port3_rx_clk_src", -- .parent_names = gcc_xo_uniphy0_rx_tx_ubi32_bias, -- .num_parents = 5, -+ .parent_data = gcc_xo_uniphy0_rx_tx_ubi32_bias, -+ .num_parents = ARRAY_SIZE(gcc_xo_uniphy0_rx_tx_ubi32_bias), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1681,9 +1580,8 @@ static struct clk_regmap_div nss_port3_r - .clkr = { - .hw.init = &(struct clk_init_data){ - .name = "nss_port3_rx_div_clk_src", -- .parent_names = (const char *[]){ -- "nss_port3_rx_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port3_rx_clk_src.clkr.hw }, - .num_parents = 1, - .ops = &clk_regmap_div_ops, - .flags = CLK_SET_RATE_PARENT, -@@ -1698,8 +1596,8 @@ static struct clk_rcg2 nss_port3_tx_clk_ - .parent_map = gcc_xo_uniphy0_tx_rx_ubi32_bias_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "nss_port3_tx_clk_src", -- .parent_names = gcc_xo_uniphy0_tx_rx_ubi32_bias, -- .num_parents = 5, -+ .parent_data = gcc_xo_uniphy0_tx_rx_ubi32_bias, -+ .num_parents = ARRAY_SIZE(gcc_xo_uniphy0_tx_rx_ubi32_bias), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1711,9 +1609,8 @@ static struct clk_regmap_div nss_port3_t - .clkr = { - .hw.init = &(struct clk_init_data){ - .name = "nss_port3_tx_div_clk_src", -- .parent_names = (const char *[]){ -- "nss_port3_tx_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port3_tx_clk_src.clkr.hw }, - .num_parents = 1, - .ops = &clk_regmap_div_ops, - .flags = CLK_SET_RATE_PARENT, -@@ -1728,8 +1625,8 @@ static struct clk_rcg2 nss_port4_rx_clk_ - .parent_map = gcc_xo_uniphy0_rx_tx_ubi32_bias_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "nss_port4_rx_clk_src", -- .parent_names = gcc_xo_uniphy0_rx_tx_ubi32_bias, -- .num_parents = 5, -+ .parent_data = gcc_xo_uniphy0_rx_tx_ubi32_bias, -+ .num_parents = ARRAY_SIZE(gcc_xo_uniphy0_rx_tx_ubi32_bias), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1741,9 +1638,8 @@ static struct clk_regmap_div nss_port4_r - .clkr = { - .hw.init = &(struct clk_init_data){ - .name = "nss_port4_rx_div_clk_src", -- .parent_names = (const char *[]){ -- "nss_port4_rx_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port4_rx_clk_src.clkr.hw }, - .num_parents = 1, - .ops = &clk_regmap_div_ops, - .flags = CLK_SET_RATE_PARENT, -@@ -1758,8 +1654,8 @@ static struct clk_rcg2 nss_port4_tx_clk_ - .parent_map = gcc_xo_uniphy0_tx_rx_ubi32_bias_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "nss_port4_tx_clk_src", -- .parent_names = gcc_xo_uniphy0_tx_rx_ubi32_bias, -- .num_parents = 5, -+ .parent_data = gcc_xo_uniphy0_tx_rx_ubi32_bias, -+ .num_parents = ARRAY_SIZE(gcc_xo_uniphy0_tx_rx_ubi32_bias), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1771,9 +1667,8 @@ static struct clk_regmap_div nss_port4_t - .clkr = { - .hw.init = &(struct clk_init_data){ - .name = "nss_port4_tx_div_clk_src", -- .parent_names = (const char *[]){ -- "nss_port4_tx_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port4_tx_clk_src.clkr.hw }, - .num_parents = 1, - .ops = &clk_regmap_div_ops, - .flags = CLK_SET_RATE_PARENT, -@@ -1793,6 +1688,27 @@ static const struct freq_tbl ftbl_nss_po - { } - }; - -+static const struct clk_parent_data gcc_xo_uniphy0_rx_tx_uniphy1_rx_tx_ubi32_bias[] = { -+ { .fw_name = "xo", .name = "xo" }, -+ { .name = "uniphy0_gcc_rx_clk" }, -+ { .name = "uniphy0_gcc_tx_clk" }, -+ { .name = "uniphy1_gcc_rx_clk" }, -+ { .name = "uniphy1_gcc_tx_clk" }, -+ { .hw = &ubi32_pll.clkr.hw }, -+ { .name = "bias_pll_cc_clk" }, -+}; -+ -+static const struct parent_map -+gcc_xo_uniphy0_rx_tx_uniphy1_rx_tx_ubi32_bias_map[] = { -+ { P_XO, 0 }, -+ { P_UNIPHY0_RX, 1 }, -+ { P_UNIPHY0_TX, 2 }, -+ { P_UNIPHY1_RX, 3 }, -+ { P_UNIPHY1_TX, 4 }, -+ { P_UBI32_PLL, 5 }, -+ { P_BIAS_PLL, 6 }, -+}; -+ - static struct clk_rcg2 nss_port5_rx_clk_src = { - .cmd_rcgr = 0x68060, - .freq_tbl = ftbl_nss_port5_rx_clk_src, -@@ -1800,8 +1716,8 @@ static struct clk_rcg2 nss_port5_rx_clk_ - .parent_map = gcc_xo_uniphy0_rx_tx_uniphy1_rx_tx_ubi32_bias_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "nss_port5_rx_clk_src", -- .parent_names = gcc_xo_uniphy0_rx_tx_uniphy1_rx_tx_ubi32_bias, -- .num_parents = 7, -+ .parent_data = gcc_xo_uniphy0_rx_tx_uniphy1_rx_tx_ubi32_bias, -+ .num_parents = ARRAY_SIZE(gcc_xo_uniphy0_rx_tx_uniphy1_rx_tx_ubi32_bias), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1813,9 +1729,8 @@ static struct clk_regmap_div nss_port5_r - .clkr = { - .hw.init = &(struct clk_init_data){ - .name = "nss_port5_rx_div_clk_src", -- .parent_names = (const char *[]){ -- "nss_port5_rx_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port5_rx_clk_src.clkr.hw }, - .num_parents = 1, - .ops = &clk_regmap_div_ops, - .flags = CLK_SET_RATE_PARENT, -@@ -1835,6 +1750,27 @@ static const struct freq_tbl ftbl_nss_po - { } - }; - -+static const struct clk_parent_data gcc_xo_uniphy0_tx_rx_uniphy1_tx_rx_ubi32_bias[] = { -+ { .fw_name = "xo", .name = "xo" }, -+ { .name = "uniphy0_gcc_tx_clk" }, -+ { .name = "uniphy0_gcc_rx_clk" }, -+ { .name = "uniphy1_gcc_tx_clk" }, -+ { .name = "uniphy1_gcc_rx_clk" }, -+ { .hw = &ubi32_pll.clkr.hw }, -+ { .name = "bias_pll_cc_clk" }, -+}; -+ -+static const struct parent_map -+gcc_xo_uniphy0_tx_rx_uniphy1_tx_rx_ubi32_bias_map[] = { -+ { P_XO, 0 }, -+ { P_UNIPHY0_TX, 1 }, -+ { P_UNIPHY0_RX, 2 }, -+ { P_UNIPHY1_TX, 3 }, -+ { P_UNIPHY1_RX, 4 }, -+ { P_UBI32_PLL, 5 }, -+ { P_BIAS_PLL, 6 }, -+}; -+ - static struct clk_rcg2 nss_port5_tx_clk_src = { - .cmd_rcgr = 0x68068, - .freq_tbl = ftbl_nss_port5_tx_clk_src, -@@ -1842,8 +1778,8 @@ static struct clk_rcg2 nss_port5_tx_clk_ - .parent_map = gcc_xo_uniphy0_tx_rx_uniphy1_tx_rx_ubi32_bias_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "nss_port5_tx_clk_src", -- .parent_names = gcc_xo_uniphy0_tx_rx_uniphy1_tx_rx_ubi32_bias, -- .num_parents = 7, -+ .parent_data = gcc_xo_uniphy0_tx_rx_uniphy1_tx_rx_ubi32_bias, -+ .num_parents = ARRAY_SIZE(gcc_xo_uniphy0_tx_rx_uniphy1_tx_rx_ubi32_bias), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1855,9 +1791,8 @@ static struct clk_regmap_div nss_port5_t - .clkr = { - .hw.init = &(struct clk_init_data){ - .name = "nss_port5_tx_div_clk_src", -- .parent_names = (const char *[]){ -- "nss_port5_tx_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port5_tx_clk_src.clkr.hw }, - .num_parents = 1, - .ops = &clk_regmap_div_ops, - .flags = CLK_SET_RATE_PARENT, -@@ -1877,6 +1812,22 @@ static const struct freq_tbl ftbl_nss_po - { } - }; - -+static const struct clk_parent_data gcc_xo_uniphy2_rx_tx_ubi32_bias[] = { -+ { .fw_name = "xo", .name = "xo" }, -+ { .name = "uniphy2_gcc_rx_clk" }, -+ { .name = "uniphy2_gcc_tx_clk" }, -+ { .hw = &ubi32_pll.clkr.hw }, -+ { .name = "bias_pll_cc_clk" }, -+}; -+ -+static const struct parent_map gcc_xo_uniphy2_rx_tx_ubi32_bias_map[] = { -+ { P_XO, 0 }, -+ { P_UNIPHY2_RX, 1 }, -+ { P_UNIPHY2_TX, 2 }, -+ { P_UBI32_PLL, 5 }, -+ { P_BIAS_PLL, 6 }, -+}; -+ - static struct clk_rcg2 nss_port6_rx_clk_src = { - .cmd_rcgr = 0x68070, - .freq_tbl = ftbl_nss_port6_rx_clk_src, -@@ -1884,8 +1835,8 @@ static struct clk_rcg2 nss_port6_rx_clk_ - .parent_map = gcc_xo_uniphy2_rx_tx_ubi32_bias_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "nss_port6_rx_clk_src", -- .parent_names = gcc_xo_uniphy2_rx_tx_ubi32_bias, -- .num_parents = 5, -+ .parent_data = gcc_xo_uniphy2_rx_tx_ubi32_bias, -+ .num_parents = ARRAY_SIZE(gcc_xo_uniphy2_rx_tx_ubi32_bias), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1897,9 +1848,8 @@ static struct clk_regmap_div nss_port6_r - .clkr = { - .hw.init = &(struct clk_init_data){ - .name = "nss_port6_rx_div_clk_src", -- .parent_names = (const char *[]){ -- "nss_port6_rx_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port6_rx_clk_src.clkr.hw }, - .num_parents = 1, - .ops = &clk_regmap_div_ops, - .flags = CLK_SET_RATE_PARENT, -@@ -1919,6 +1869,22 @@ static const struct freq_tbl ftbl_nss_po - { } - }; - -+static const struct clk_parent_data gcc_xo_uniphy2_tx_rx_ubi32_bias[] = { -+ { .fw_name = "xo", .name = "xo" }, -+ { .name = "uniphy2_gcc_tx_clk" }, -+ { .name = "uniphy2_gcc_rx_clk" }, -+ { .hw = &ubi32_pll.clkr.hw }, -+ { .name = "bias_pll_cc_clk" }, -+}; -+ -+static const struct parent_map gcc_xo_uniphy2_tx_rx_ubi32_bias_map[] = { -+ { P_XO, 0 }, -+ { P_UNIPHY2_TX, 1 }, -+ { P_UNIPHY2_RX, 2 }, -+ { P_UBI32_PLL, 5 }, -+ { P_BIAS_PLL, 6 }, -+}; -+ - static struct clk_rcg2 nss_port6_tx_clk_src = { - .cmd_rcgr = 0x68078, - .freq_tbl = ftbl_nss_port6_tx_clk_src, -@@ -1926,8 +1892,8 @@ static struct clk_rcg2 nss_port6_tx_clk_ - .parent_map = gcc_xo_uniphy2_tx_rx_ubi32_bias_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "nss_port6_tx_clk_src", -- .parent_names = gcc_xo_uniphy2_tx_rx_ubi32_bias, -- .num_parents = 5, -+ .parent_data = gcc_xo_uniphy2_tx_rx_ubi32_bias, -+ .num_parents = ARRAY_SIZE(gcc_xo_uniphy2_tx_rx_ubi32_bias), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1939,9 +1905,8 @@ static struct clk_regmap_div nss_port6_t - .clkr = { - .hw.init = &(struct clk_init_data){ - .name = "nss_port6_tx_div_clk_src", -- .parent_names = (const char *[]){ -- "nss_port6_tx_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port6_tx_clk_src.clkr.hw }, - .num_parents = 1, - .ops = &clk_regmap_div_ops, - .flags = CLK_SET_RATE_PARENT, -@@ -1964,8 +1929,8 @@ static struct clk_rcg2 crypto_clk_src = - .parent_map = gcc_xo_gpll0_gpll0_out_main_div2_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "crypto_clk_src", -- .parent_names = gcc_xo_gpll0_gpll0_out_main_div2, -- .num_parents = 3, -+ .parent_data = gcc_xo_gpll0_gpll0_out_main_div2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll0_out_main_div2), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1975,6 +1940,22 @@ static struct freq_tbl ftbl_gp_clk_src[] - { } - }; - -+static const struct clk_parent_data gcc_xo_gpll0_gpll6_gpll0_sleep_clk[] = { -+ { .fw_name = "xo", .name = "xo" }, -+ { .hw = &gpll0.clkr.hw }, -+ { .hw = &gpll6.clkr.hw }, -+ { .hw = &gpll0_out_main_div2.hw }, -+ { .fw_name = "sleep_clk", .name = "sleep_clk" }, -+}; -+ -+static const struct parent_map gcc_xo_gpll0_gpll6_gpll0_sleep_clk_map[] = { -+ { P_XO, 0 }, -+ { P_GPLL0, 1 }, -+ { P_GPLL6, 2 }, -+ { P_GPLL0_DIV2, 4 }, -+ { P_SLEEP_CLK, 6 }, -+}; -+ - static struct clk_rcg2 gp1_clk_src = { - .cmd_rcgr = 0x08004, - .freq_tbl = ftbl_gp_clk_src, -@@ -1983,8 +1964,8 @@ static struct clk_rcg2 gp1_clk_src = { - .parent_map = gcc_xo_gpll0_gpll6_gpll0_sleep_clk_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "gp1_clk_src", -- .parent_names = gcc_xo_gpll0_gpll6_gpll0_sleep_clk, -- .num_parents = 5, -+ .parent_data = gcc_xo_gpll0_gpll6_gpll0_sleep_clk, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll6_gpll0_sleep_clk), - .ops = &clk_rcg2_ops, - }, - }; -@@ -1997,8 +1978,8 @@ static struct clk_rcg2 gp2_clk_src = { - .parent_map = gcc_xo_gpll0_gpll6_gpll0_sleep_clk_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "gp2_clk_src", -- .parent_names = gcc_xo_gpll0_gpll6_gpll0_sleep_clk, -- .num_parents = 5, -+ .parent_data = gcc_xo_gpll0_gpll6_gpll0_sleep_clk, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll6_gpll0_sleep_clk), - .ops = &clk_rcg2_ops, - }, - }; -@@ -2011,8 +1992,8 @@ static struct clk_rcg2 gp3_clk_src = { - .parent_map = gcc_xo_gpll0_gpll6_gpll0_sleep_clk_map, - .clkr.hw.init = &(struct clk_init_data){ - .name = "gp3_clk_src", -- .parent_names = gcc_xo_gpll0_gpll6_gpll0_sleep_clk, -- .num_parents = 5, -+ .parent_data = gcc_xo_gpll0_gpll6_gpll0_sleep_clk, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0_gpll6_gpll0_sleep_clk), - .ops = &clk_rcg2_ops, - }, - }; -@@ -2024,9 +2005,8 @@ static struct clk_branch gcc_blsp1_ahb_c - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_blsp1_ahb_clk", -- .parent_names = (const char *[]){ -- "pcnoc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcnoc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2041,9 +2021,8 @@ static struct clk_branch gcc_blsp1_qup1_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_blsp1_qup1_i2c_apps_clk", -- .parent_names = (const char *[]){ -- "blsp1_qup1_i2c_apps_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &blsp1_qup1_i2c_apps_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2058,9 +2037,8 @@ static struct clk_branch gcc_blsp1_qup1_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_blsp1_qup1_spi_apps_clk", -- .parent_names = (const char *[]){ -- "blsp1_qup1_spi_apps_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &blsp1_qup1_spi_apps_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2075,9 +2053,8 @@ static struct clk_branch gcc_blsp1_qup2_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_blsp1_qup2_i2c_apps_clk", -- .parent_names = (const char *[]){ -- "blsp1_qup2_i2c_apps_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &blsp1_qup2_i2c_apps_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2092,9 +2069,8 @@ static struct clk_branch gcc_blsp1_qup2_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_blsp1_qup2_spi_apps_clk", -- .parent_names = (const char *[]){ -- "blsp1_qup2_spi_apps_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &blsp1_qup2_spi_apps_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2109,9 +2085,8 @@ static struct clk_branch gcc_blsp1_qup3_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_blsp1_qup3_i2c_apps_clk", -- .parent_names = (const char *[]){ -- "blsp1_qup3_i2c_apps_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &blsp1_qup3_i2c_apps_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2126,9 +2101,8 @@ static struct clk_branch gcc_blsp1_qup3_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_blsp1_qup3_spi_apps_clk", -- .parent_names = (const char *[]){ -- "blsp1_qup3_spi_apps_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &blsp1_qup3_spi_apps_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2143,9 +2117,8 @@ static struct clk_branch gcc_blsp1_qup4_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_blsp1_qup4_i2c_apps_clk", -- .parent_names = (const char *[]){ -- "blsp1_qup4_i2c_apps_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &blsp1_qup4_i2c_apps_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2160,9 +2133,8 @@ static struct clk_branch gcc_blsp1_qup4_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_blsp1_qup4_spi_apps_clk", -- .parent_names = (const char *[]){ -- "blsp1_qup4_spi_apps_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &blsp1_qup4_spi_apps_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2177,9 +2149,8 @@ static struct clk_branch gcc_blsp1_qup5_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_blsp1_qup5_i2c_apps_clk", -- .parent_names = (const char *[]){ -- "blsp1_qup5_i2c_apps_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &blsp1_qup5_i2c_apps_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2194,9 +2165,8 @@ static struct clk_branch gcc_blsp1_qup5_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_blsp1_qup5_spi_apps_clk", -- .parent_names = (const char *[]){ -- "blsp1_qup5_spi_apps_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &blsp1_qup5_spi_apps_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2211,9 +2181,8 @@ static struct clk_branch gcc_blsp1_qup6_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_blsp1_qup6_i2c_apps_clk", -- .parent_names = (const char *[]){ -- "blsp1_qup6_i2c_apps_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &blsp1_qup6_i2c_apps_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2228,9 +2197,8 @@ static struct clk_branch gcc_blsp1_qup6_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_blsp1_qup6_spi_apps_clk", -- .parent_names = (const char *[]){ -- "blsp1_qup6_spi_apps_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &blsp1_qup6_spi_apps_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2245,9 +2213,8 @@ static struct clk_branch gcc_blsp1_uart1 - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_blsp1_uart1_apps_clk", -- .parent_names = (const char *[]){ -- "blsp1_uart1_apps_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &blsp1_uart1_apps_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2262,9 +2229,8 @@ static struct clk_branch gcc_blsp1_uart2 - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_blsp1_uart2_apps_clk", -- .parent_names = (const char *[]){ -- "blsp1_uart2_apps_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &blsp1_uart2_apps_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2279,9 +2245,8 @@ static struct clk_branch gcc_blsp1_uart3 - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_blsp1_uart3_apps_clk", -- .parent_names = (const char *[]){ -- "blsp1_uart3_apps_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &blsp1_uart3_apps_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2296,9 +2261,8 @@ static struct clk_branch gcc_blsp1_uart4 - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_blsp1_uart4_apps_clk", -- .parent_names = (const char *[]){ -- "blsp1_uart4_apps_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &blsp1_uart4_apps_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2313,9 +2277,8 @@ static struct clk_branch gcc_blsp1_uart5 - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_blsp1_uart5_apps_clk", -- .parent_names = (const char *[]){ -- "blsp1_uart5_apps_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &blsp1_uart5_apps_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2330,9 +2293,8 @@ static struct clk_branch gcc_blsp1_uart6 - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_blsp1_uart6_apps_clk", -- .parent_names = (const char *[]){ -- "blsp1_uart6_apps_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &blsp1_uart6_apps_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2348,9 +2310,8 @@ static struct clk_branch gcc_prng_ahb_cl - .enable_mask = BIT(8), - .hw.init = &(struct clk_init_data){ - .name = "gcc_prng_ahb_clk", -- .parent_names = (const char *[]){ -- "pcnoc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcnoc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2365,9 +2326,8 @@ static struct clk_branch gcc_qpic_ahb_cl - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_qpic_ahb_clk", -- .parent_names = (const char *[]){ -- "pcnoc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcnoc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2382,9 +2342,8 @@ static struct clk_branch gcc_qpic_clk = - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_qpic_clk", -- .parent_names = (const char *[]){ -- "pcnoc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcnoc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2399,9 +2358,8 @@ static struct clk_branch gcc_pcie0_ahb_c - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_pcie0_ahb_clk", -- .parent_names = (const char *[]){ -- "pcnoc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcnoc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2416,9 +2374,8 @@ static struct clk_branch gcc_pcie0_aux_c - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_pcie0_aux_clk", -- .parent_names = (const char *[]){ -- "pcie0_aux_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcie0_aux_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2433,9 +2390,8 @@ static struct clk_branch gcc_pcie0_axi_m - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_pcie0_axi_m_clk", -- .parent_names = (const char *[]){ -- "pcie0_axi_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcie0_axi_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2450,9 +2406,8 @@ static struct clk_branch gcc_pcie0_axi_s - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_pcie0_axi_s_clk", -- .parent_names = (const char *[]){ -- "pcie0_axi_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcie0_axi_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2468,9 +2423,8 @@ static struct clk_branch gcc_pcie0_pipe_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_pcie0_pipe_clk", -- .parent_names = (const char *[]){ -- "pcie0_pipe_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcie0_pipe_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2485,9 +2439,8 @@ static struct clk_branch gcc_sys_noc_pci - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_sys_noc_pcie0_axi_clk", -- .parent_names = (const char *[]){ -- "pcie0_axi_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcie0_axi_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2502,9 +2455,8 @@ static struct clk_branch gcc_pcie1_ahb_c - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_pcie1_ahb_clk", -- .parent_names = (const char *[]){ -- "pcnoc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcnoc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2519,9 +2471,8 @@ static struct clk_branch gcc_pcie1_aux_c - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_pcie1_aux_clk", -- .parent_names = (const char *[]){ -- "pcie1_aux_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcie1_aux_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2536,9 +2487,8 @@ static struct clk_branch gcc_pcie1_axi_m - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_pcie1_axi_m_clk", -- .parent_names = (const char *[]){ -- "pcie1_axi_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcie1_axi_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2553,9 +2503,8 @@ static struct clk_branch gcc_pcie1_axi_s - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_pcie1_axi_s_clk", -- .parent_names = (const char *[]){ -- "pcie1_axi_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcie1_axi_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2571,9 +2520,8 @@ static struct clk_branch gcc_pcie1_pipe_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_pcie1_pipe_clk", -- .parent_names = (const char *[]){ -- "pcie1_pipe_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcie1_pipe_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2588,9 +2536,8 @@ static struct clk_branch gcc_sys_noc_pci - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_sys_noc_pcie1_axi_clk", -- .parent_names = (const char *[]){ -- "pcie1_axi_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcie1_axi_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2605,9 +2552,8 @@ static struct clk_branch gcc_usb0_aux_cl - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_usb0_aux_clk", -- .parent_names = (const char *[]){ -- "usb0_aux_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &usb0_aux_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2622,9 +2568,8 @@ static struct clk_branch gcc_sys_noc_usb - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_sys_noc_usb0_axi_clk", -- .parent_names = (const char *[]){ -- "usb0_master_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &usb0_master_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2639,9 +2584,8 @@ static struct clk_branch gcc_usb0_master - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_usb0_master_clk", -- .parent_names = (const char *[]){ -- "usb0_master_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &usb0_master_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2656,9 +2600,8 @@ static struct clk_branch gcc_usb0_mock_u - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_usb0_mock_utmi_clk", -- .parent_names = (const char *[]){ -- "usb0_mock_utmi_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &usb0_mock_utmi_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2673,9 +2616,8 @@ static struct clk_branch gcc_usb0_phy_cf - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_usb0_phy_cfg_ahb_clk", -- .parent_names = (const char *[]){ -- "pcnoc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcnoc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2691,9 +2633,8 @@ static struct clk_branch gcc_usb0_pipe_c - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_usb0_pipe_clk", -- .parent_names = (const char *[]){ -- "usb0_pipe_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &usb0_pipe_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2708,9 +2649,8 @@ static struct clk_branch gcc_usb0_sleep_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_usb0_sleep_clk", -- .parent_names = (const char *[]){ -- "gcc_sleep_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &gcc_sleep_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2725,9 +2665,8 @@ static struct clk_branch gcc_usb1_aux_cl - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_usb1_aux_clk", -- .parent_names = (const char *[]){ -- "usb1_aux_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &usb1_aux_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2742,9 +2681,8 @@ static struct clk_branch gcc_sys_noc_usb - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_sys_noc_usb1_axi_clk", -- .parent_names = (const char *[]){ -- "usb1_master_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &usb1_master_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2759,9 +2697,8 @@ static struct clk_branch gcc_usb1_master - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_usb1_master_clk", -- .parent_names = (const char *[]){ -- "usb1_master_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &usb1_master_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2776,9 +2713,8 @@ static struct clk_branch gcc_usb1_mock_u - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_usb1_mock_utmi_clk", -- .parent_names = (const char *[]){ -- "usb1_mock_utmi_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &usb1_mock_utmi_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2793,9 +2729,8 @@ static struct clk_branch gcc_usb1_phy_cf - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_usb1_phy_cfg_ahb_clk", -- .parent_names = (const char *[]){ -- "pcnoc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcnoc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2811,9 +2746,8 @@ static struct clk_branch gcc_usb1_pipe_c - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_usb1_pipe_clk", -- .parent_names = (const char *[]){ -- "usb1_pipe_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &usb1_pipe_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2828,9 +2762,8 @@ static struct clk_branch gcc_usb1_sleep_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_usb1_sleep_clk", -- .parent_names = (const char *[]){ -- "gcc_sleep_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &gcc_sleep_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2845,9 +2778,8 @@ static struct clk_branch gcc_sdcc1_ahb_c - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_sdcc1_ahb_clk", -- .parent_names = (const char *[]){ -- "pcnoc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcnoc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2862,9 +2794,8 @@ static struct clk_branch gcc_sdcc1_apps_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_sdcc1_apps_clk", -- .parent_names = (const char *[]){ -- "sdcc1_apps_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &sdcc1_apps_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2879,9 +2810,8 @@ static struct clk_branch gcc_sdcc1_ice_c - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_sdcc1_ice_core_clk", -- .parent_names = (const char *[]){ -- "sdcc1_ice_core_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &sdcc1_ice_core_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2896,9 +2826,8 @@ static struct clk_branch gcc_sdcc2_ahb_c - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_sdcc2_ahb_clk", -- .parent_names = (const char *[]){ -- "pcnoc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcnoc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2913,9 +2842,8 @@ static struct clk_branch gcc_sdcc2_apps_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_sdcc2_apps_clk", -- .parent_names = (const char *[]){ -- "sdcc2_apps_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &sdcc2_apps_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2930,9 +2858,8 @@ static struct clk_branch gcc_mem_noc_nss - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_mem_noc_nss_axi_clk", -- .parent_names = (const char *[]){ -- "nss_noc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_noc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2947,9 +2874,8 @@ static struct clk_branch gcc_nss_ce_apb_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_ce_apb_clk", -- .parent_names = (const char *[]){ -- "nss_ce_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ce_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2964,9 +2890,8 @@ static struct clk_branch gcc_nss_ce_axi_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_ce_axi_clk", -- .parent_names = (const char *[]){ -- "nss_ce_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ce_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2981,9 +2906,8 @@ static struct clk_branch gcc_nss_cfg_clk - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_cfg_clk", -- .parent_names = (const char *[]){ -- "pcnoc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcnoc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -2998,9 +2922,8 @@ static struct clk_branch gcc_nss_crypto_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_crypto_clk", -- .parent_names = (const char *[]){ -- "nss_crypto_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_crypto_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3015,9 +2938,8 @@ static struct clk_branch gcc_nss_csr_clk - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_csr_clk", -- .parent_names = (const char *[]){ -- "nss_ce_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ce_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3032,9 +2954,8 @@ static struct clk_branch gcc_nss_edma_cf - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_edma_cfg_clk", -- .parent_names = (const char *[]){ -- "nss_ppe_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ppe_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3049,9 +2970,8 @@ static struct clk_branch gcc_nss_edma_cl - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_edma_clk", -- .parent_names = (const char *[]){ -- "nss_ppe_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ppe_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3066,9 +2986,8 @@ static struct clk_branch gcc_nss_imem_cl - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_imem_clk", -- .parent_names = (const char *[]){ -- "nss_imem_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_imem_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3083,9 +3002,8 @@ static struct clk_branch gcc_nss_noc_clk - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_noc_clk", -- .parent_names = (const char *[]){ -- "nss_noc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_noc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3100,9 +3018,8 @@ static struct clk_branch gcc_nss_ppe_btq - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_ppe_btq_clk", -- .parent_names = (const char *[]){ -- "nss_ppe_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ppe_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3117,9 +3034,8 @@ static struct clk_branch gcc_nss_ppe_cfg - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_ppe_cfg_clk", -- .parent_names = (const char *[]){ -- "nss_ppe_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ppe_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3134,9 +3050,8 @@ static struct clk_branch gcc_nss_ppe_clk - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_ppe_clk", -- .parent_names = (const char *[]){ -- "nss_ppe_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ppe_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3151,9 +3066,8 @@ static struct clk_branch gcc_nss_ppe_ipe - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_ppe_ipe_clk", -- .parent_names = (const char *[]){ -- "nss_ppe_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ppe_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3168,9 +3082,8 @@ static struct clk_branch gcc_nss_ptp_ref - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_ptp_ref_clk", -- .parent_names = (const char *[]){ -- "nss_ppe_cdiv_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ppe_cdiv_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3186,9 +3099,8 @@ static struct clk_branch gcc_crypto_ppe_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_crypto_ppe_clk", -- .parent_names = (const char *[]){ -- "nss_ppe_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ppe_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3203,9 +3115,8 @@ static struct clk_branch gcc_nssnoc_ce_a - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nssnoc_ce_apb_clk", -- .parent_names = (const char *[]){ -- "nss_ce_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ce_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3220,9 +3131,8 @@ static struct clk_branch gcc_nssnoc_ce_a - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nssnoc_ce_axi_clk", -- .parent_names = (const char *[]){ -- "nss_ce_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ce_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3237,9 +3147,8 @@ static struct clk_branch gcc_nssnoc_cryp - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nssnoc_crypto_clk", -- .parent_names = (const char *[]){ -- "nss_crypto_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_crypto_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3254,9 +3163,8 @@ static struct clk_branch gcc_nssnoc_ppe_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nssnoc_ppe_cfg_clk", -- .parent_names = (const char *[]){ -- "nss_ppe_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ppe_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3271,9 +3179,8 @@ static struct clk_branch gcc_nssnoc_ppe_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nssnoc_ppe_clk", -- .parent_names = (const char *[]){ -- "nss_ppe_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ppe_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3288,9 +3195,8 @@ static struct clk_branch gcc_nssnoc_qosg - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nssnoc_qosgen_ref_clk", -- .parent_names = (const char *[]){ -- "gcc_xo_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &gcc_xo_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3305,9 +3211,8 @@ static struct clk_branch gcc_nssnoc_snoc - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nssnoc_snoc_clk", -- .parent_names = (const char *[]){ -- "system_noc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &system_noc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3322,9 +3227,8 @@ static struct clk_branch gcc_nssnoc_time - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nssnoc_timeout_ref_clk", -- .parent_names = (const char *[]){ -- "gcc_xo_div4_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &gcc_xo_div4_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3339,9 +3243,8 @@ static struct clk_branch gcc_nssnoc_ubi0 - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nssnoc_ubi0_ahb_clk", -- .parent_names = (const char *[]){ -- "nss_ce_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ce_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3356,9 +3259,8 @@ static struct clk_branch gcc_nssnoc_ubi1 - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nssnoc_ubi1_ahb_clk", -- .parent_names = (const char *[]){ -- "nss_ce_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ce_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3374,9 +3276,8 @@ static struct clk_branch gcc_ubi0_ahb_cl - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_ubi0_ahb_clk", -- .parent_names = (const char *[]){ -- "nss_ce_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ce_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3392,9 +3293,8 @@ static struct clk_branch gcc_ubi0_axi_cl - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_ubi0_axi_clk", -- .parent_names = (const char *[]){ -- "nss_noc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_noc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3410,9 +3310,8 @@ static struct clk_branch gcc_ubi0_nc_axi - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_ubi0_nc_axi_clk", -- .parent_names = (const char *[]){ -- "nss_noc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_noc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3428,9 +3327,8 @@ static struct clk_branch gcc_ubi0_core_c - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_ubi0_core_clk", -- .parent_names = (const char *[]){ -- "nss_ubi0_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ubi0_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3446,9 +3344,8 @@ static struct clk_branch gcc_ubi0_mpt_cl - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_ubi0_mpt_clk", -- .parent_names = (const char *[]){ -- "ubi_mpt_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &ubi_mpt_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3464,9 +3361,8 @@ static struct clk_branch gcc_ubi1_ahb_cl - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_ubi1_ahb_clk", -- .parent_names = (const char *[]){ -- "nss_ce_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ce_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3482,9 +3378,8 @@ static struct clk_branch gcc_ubi1_axi_cl - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_ubi1_axi_clk", -- .parent_names = (const char *[]){ -- "nss_noc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_noc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3500,9 +3395,8 @@ static struct clk_branch gcc_ubi1_nc_axi - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_ubi1_nc_axi_clk", -- .parent_names = (const char *[]){ -- "nss_noc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_noc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3518,9 +3412,8 @@ static struct clk_branch gcc_ubi1_core_c - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_ubi1_core_clk", -- .parent_names = (const char *[]){ -- "nss_ubi1_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ubi1_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3536,9 +3429,8 @@ static struct clk_branch gcc_ubi1_mpt_cl - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_ubi1_mpt_clk", -- .parent_names = (const char *[]){ -- "ubi_mpt_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &ubi_mpt_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3553,9 +3445,8 @@ static struct clk_branch gcc_cmn_12gpll_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_cmn_12gpll_ahb_clk", -- .parent_names = (const char *[]){ -- "pcnoc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcnoc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3570,9 +3461,8 @@ static struct clk_branch gcc_cmn_12gpll_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_cmn_12gpll_sys_clk", -- .parent_names = (const char *[]){ -- "gcc_xo_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &gcc_xo_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3587,9 +3477,8 @@ static struct clk_branch gcc_mdio_ahb_cl - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_mdio_ahb_clk", -- .parent_names = (const char *[]){ -- "pcnoc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcnoc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3604,9 +3493,8 @@ static struct clk_branch gcc_uniphy0_ahb - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_uniphy0_ahb_clk", -- .parent_names = (const char *[]){ -- "pcnoc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcnoc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3621,9 +3509,8 @@ static struct clk_branch gcc_uniphy0_sys - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_uniphy0_sys_clk", -- .parent_names = (const char *[]){ -- "gcc_xo_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &gcc_xo_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3638,9 +3525,8 @@ static struct clk_branch gcc_uniphy1_ahb - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_uniphy1_ahb_clk", -- .parent_names = (const char *[]){ -- "pcnoc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcnoc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3655,9 +3541,8 @@ static struct clk_branch gcc_uniphy1_sys - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_uniphy1_sys_clk", -- .parent_names = (const char *[]){ -- "gcc_xo_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &gcc_xo_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3672,9 +3557,8 @@ static struct clk_branch gcc_uniphy2_ahb - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_uniphy2_ahb_clk", -- .parent_names = (const char *[]){ -- "pcnoc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcnoc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3689,9 +3573,8 @@ static struct clk_branch gcc_uniphy2_sys - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_uniphy2_sys_clk", -- .parent_names = (const char *[]){ -- "gcc_xo_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &gcc_xo_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3706,9 +3589,8 @@ static struct clk_branch gcc_nss_port1_r - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_port1_rx_clk", -- .parent_names = (const char *[]){ -- "nss_port1_rx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port1_rx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3723,9 +3605,8 @@ static struct clk_branch gcc_nss_port1_t - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_port1_tx_clk", -- .parent_names = (const char *[]){ -- "nss_port1_tx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port1_tx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3740,9 +3621,8 @@ static struct clk_branch gcc_nss_port2_r - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_port2_rx_clk", -- .parent_names = (const char *[]){ -- "nss_port2_rx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port2_rx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3757,9 +3637,8 @@ static struct clk_branch gcc_nss_port2_t - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_port2_tx_clk", -- .parent_names = (const char *[]){ -- "nss_port2_tx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port2_tx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3774,9 +3653,8 @@ static struct clk_branch gcc_nss_port3_r - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_port3_rx_clk", -- .parent_names = (const char *[]){ -- "nss_port3_rx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port3_rx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3791,9 +3669,8 @@ static struct clk_branch gcc_nss_port3_t - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_port3_tx_clk", -- .parent_names = (const char *[]){ -- "nss_port3_tx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port3_tx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3808,9 +3685,8 @@ static struct clk_branch gcc_nss_port4_r - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_port4_rx_clk", -- .parent_names = (const char *[]){ -- "nss_port4_rx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port4_rx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3825,9 +3701,8 @@ static struct clk_branch gcc_nss_port4_t - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_port4_tx_clk", -- .parent_names = (const char *[]){ -- "nss_port4_tx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port4_tx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3842,9 +3717,8 @@ static struct clk_branch gcc_nss_port5_r - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_port5_rx_clk", -- .parent_names = (const char *[]){ -- "nss_port5_rx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port5_rx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3859,9 +3733,8 @@ static struct clk_branch gcc_nss_port5_t - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_port5_tx_clk", -- .parent_names = (const char *[]){ -- "nss_port5_tx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port5_tx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3876,9 +3749,8 @@ static struct clk_branch gcc_nss_port6_r - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_port6_rx_clk", -- .parent_names = (const char *[]){ -- "nss_port6_rx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port6_rx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3893,9 +3765,8 @@ static struct clk_branch gcc_nss_port6_t - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_nss_port6_tx_clk", -- .parent_names = (const char *[]){ -- "nss_port6_tx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port6_tx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3910,9 +3781,8 @@ static struct clk_branch gcc_port1_mac_c - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_port1_mac_clk", -- .parent_names = (const char *[]){ -- "nss_ppe_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ppe_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3927,9 +3797,8 @@ static struct clk_branch gcc_port2_mac_c - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_port2_mac_clk", -- .parent_names = (const char *[]){ -- "nss_ppe_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ppe_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3944,9 +3813,8 @@ static struct clk_branch gcc_port3_mac_c - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_port3_mac_clk", -- .parent_names = (const char *[]){ -- "nss_ppe_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ppe_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3961,9 +3829,8 @@ static struct clk_branch gcc_port4_mac_c - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_port4_mac_clk", -- .parent_names = (const char *[]){ -- "nss_ppe_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ppe_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3978,9 +3845,8 @@ static struct clk_branch gcc_port5_mac_c - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_port5_mac_clk", -- .parent_names = (const char *[]){ -- "nss_ppe_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ppe_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -3995,9 +3861,8 @@ static struct clk_branch gcc_port6_mac_c - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_port6_mac_clk", -- .parent_names = (const char *[]){ -- "nss_ppe_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_ppe_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -4012,9 +3877,8 @@ static struct clk_branch gcc_uniphy0_por - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_uniphy0_port1_rx_clk", -- .parent_names = (const char *[]){ -- "nss_port1_rx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port1_rx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -4029,9 +3893,8 @@ static struct clk_branch gcc_uniphy0_por - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_uniphy0_port1_tx_clk", -- .parent_names = (const char *[]){ -- "nss_port1_tx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port1_tx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -4046,9 +3909,8 @@ static struct clk_branch gcc_uniphy0_por - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_uniphy0_port2_rx_clk", -- .parent_names = (const char *[]){ -- "nss_port2_rx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port2_rx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -4063,9 +3925,8 @@ static struct clk_branch gcc_uniphy0_por - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_uniphy0_port2_tx_clk", -- .parent_names = (const char *[]){ -- "nss_port2_tx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port2_tx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -4080,9 +3941,8 @@ static struct clk_branch gcc_uniphy0_por - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_uniphy0_port3_rx_clk", -- .parent_names = (const char *[]){ -- "nss_port3_rx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port3_rx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -4097,9 +3957,8 @@ static struct clk_branch gcc_uniphy0_por - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_uniphy0_port3_tx_clk", -- .parent_names = (const char *[]){ -- "nss_port3_tx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port3_tx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -4114,9 +3973,8 @@ static struct clk_branch gcc_uniphy0_por - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_uniphy0_port4_rx_clk", -- .parent_names = (const char *[]){ -- "nss_port4_rx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port4_rx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -4131,9 +3989,8 @@ static struct clk_branch gcc_uniphy0_por - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_uniphy0_port4_tx_clk", -- .parent_names = (const char *[]){ -- "nss_port4_tx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port4_tx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -4148,9 +4005,8 @@ static struct clk_branch gcc_uniphy0_por - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_uniphy0_port5_rx_clk", -- .parent_names = (const char *[]){ -- "nss_port5_rx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port5_rx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -4165,9 +4021,8 @@ static struct clk_branch gcc_uniphy0_por - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_uniphy0_port5_tx_clk", -- .parent_names = (const char *[]){ -- "nss_port5_tx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port5_tx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -4182,9 +4037,8 @@ static struct clk_branch gcc_uniphy1_por - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_uniphy1_port5_rx_clk", -- .parent_names = (const char *[]){ -- "nss_port5_rx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port5_rx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -4199,9 +4053,8 @@ static struct clk_branch gcc_uniphy1_por - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_uniphy1_port5_tx_clk", -- .parent_names = (const char *[]){ -- "nss_port5_tx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port5_tx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -4216,9 +4069,8 @@ static struct clk_branch gcc_uniphy2_por - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_uniphy2_port6_rx_clk", -- .parent_names = (const char *[]){ -- "nss_port6_rx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port6_rx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -4233,9 +4085,8 @@ static struct clk_branch gcc_uniphy2_por - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_uniphy2_port6_tx_clk", -- .parent_names = (const char *[]){ -- "nss_port6_tx_div_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &nss_port6_tx_div_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -4251,9 +4102,8 @@ static struct clk_branch gcc_crypto_ahb_ - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_crypto_ahb_clk", -- .parent_names = (const char *[]){ -- "pcnoc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcnoc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -4269,9 +4119,8 @@ static struct clk_branch gcc_crypto_axi_ - .enable_mask = BIT(1), - .hw.init = &(struct clk_init_data){ - .name = "gcc_crypto_axi_clk", -- .parent_names = (const char *[]){ -- "pcnoc_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &pcnoc_clk_src.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -4287,9 +4136,8 @@ static struct clk_branch gcc_crypto_clk - .enable_mask = BIT(2), - .hw.init = &(struct clk_init_data){ - .name = "gcc_crypto_clk", -- .parent_names = (const char *[]){ -- "crypto_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &crypto_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -4304,9 +4152,8 @@ static struct clk_branch gcc_gp1_clk = { - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_gp1_clk", -- .parent_names = (const char *[]){ -- "gp1_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &gp1_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -4321,9 +4168,8 @@ static struct clk_branch gcc_gp2_clk = { - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_gp2_clk", -- .parent_names = (const char *[]){ -- "gp2_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &gp2_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -4338,9 +4184,8 @@ static struct clk_branch gcc_gp3_clk = { - .enable_mask = BIT(0), - .hw.init = &(struct clk_init_data){ - .name = "gcc_gp3_clk", -- .parent_names = (const char *[]){ -- "gp3_clk_src" -- }, -+ .parent_hws = (const struct clk_hw *[]){ -+ &gp3_clk_src.clkr.hw }, - .num_parents = 1, - .flags = CLK_SET_RATE_PARENT, - .ops = &clk_branch2_ops, -@@ -4362,7 +4207,7 @@ static struct clk_rcg2 pcie0_rchng_clk_s - .clkr.hw.init = &(struct clk_init_data){ - .name = "pcie0_rchng_clk_src", - .parent_data = gcc_xo_gpll0, -- .num_parents = 2, -+ .num_parents = ARRAY_SIZE(gcc_xo_gpll0), - .ops = &clk_rcg2_ops, - }, - }; diff --git a/target/linux/qualcommax/patches-6.1/0008-v6.2-arm64-dts-qcom-ipq6018-fix-NAND-node-name.patch b/target/linux/qualcommax/patches-6.1/0008-v6.2-arm64-dts-qcom-ipq6018-fix-NAND-node-name.patch deleted file mode 100644 index a87ae4b8ad..0000000000 --- a/target/linux/qualcommax/patches-6.1/0008-v6.2-arm64-dts-qcom-ipq6018-fix-NAND-node-name.patch +++ /dev/null @@ -1,28 +0,0 @@ -From 8857b0ab6a562c473c5bded0efda9390b82a84d4 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Tue, 27 Sep 2022 22:12:17 +0200 -Subject: [PATCH] arm64: dts: qcom: ipq6018: fix NAND node name - -Per schema it should be nand-controller@79b0000 instead of nand@79b0000. -Fix it to match nand-controller.yaml requirements. - -Signed-off-by: Robert Marko -Reviewed-by: Krzysztof Kozlowski -Reviewed-by: Neil Armstrong -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20220927201218.1264506-1-robimarko@gmail.com ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 2 +- - 1 file changed, 1 insertion(+), 1 deletion(-) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -348,7 +348,7 @@ - status = "disabled"; - }; - -- qpic_nand: nand@79b0000 { -+ qpic_nand: nand-controller@79b0000 { - compatible = "qcom,ipq6018-nand"; - reg = <0x0 0x079b0000 0x0 0x10000>; - #address-cells = <1>; diff --git a/target/linux/qualcommax/patches-6.1/0009-v6.2-dt-bindings-clock-qcom-ipq8074-add-missing-networkin.patch b/target/linux/qualcommax/patches-6.1/0009-v6.2-dt-bindings-clock-qcom-ipq8074-add-missing-networkin.patch deleted file mode 100644 index 75f16a1673..0000000000 --- a/target/linux/qualcommax/patches-6.1/0009-v6.2-dt-bindings-clock-qcom-ipq8074-add-missing-networkin.patch +++ /dev/null @@ -1,39 +0,0 @@ -From e78a40eb24187a8b4f9b89e2181f674df39c2013 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Mon, 7 Nov 2022 14:29:00 +0100 -Subject: [PATCH] dt-bindings: clock: qcom: ipq8074: add missing networking - resets - -Add bindings for the missing networking resets found in IPQ8074 GCC. - -Signed-off-by: Robert Marko -Acked-by: Krzysztof Kozlowski -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20221107132901.489240-2-robimarko@gmail.com ---- - include/dt-bindings/clock/qcom,gcc-ipq8074.h | 14 ++++++++++++++ - 1 file changed, 14 insertions(+) - ---- a/include/dt-bindings/clock/qcom,gcc-ipq8074.h -+++ b/include/dt-bindings/clock/qcom,gcc-ipq8074.h -@@ -367,6 +367,20 @@ - #define GCC_PCIE1_AHB_ARES 129 - #define GCC_PCIE1_AXI_MASTER_STICKY_ARES 130 - #define GCC_PCIE0_AXI_SLAVE_STICKY_ARES 131 -+#define GCC_PPE_FULL_RESET 132 -+#define GCC_UNIPHY0_SOFT_RESET 133 -+#define GCC_UNIPHY0_XPCS_RESET 134 -+#define GCC_UNIPHY1_SOFT_RESET 135 -+#define GCC_UNIPHY1_XPCS_RESET 136 -+#define GCC_UNIPHY2_SOFT_RESET 137 -+#define GCC_UNIPHY2_XPCS_RESET 138 -+#define GCC_EDMA_HW_RESET 139 -+#define GCC_NSSPORT1_RESET 140 -+#define GCC_NSSPORT2_RESET 141 -+#define GCC_NSSPORT3_RESET 142 -+#define GCC_NSSPORT4_RESET 143 -+#define GCC_NSSPORT5_RESET 144 -+#define GCC_NSSPORT6_RESET 145 - - #define USB0_GDSC 0 - #define USB1_GDSC 1 diff --git a/target/linux/qualcommax/patches-6.1/0010-v6.2-clk-qcom-ipq8074-add-missing-networking-resets.patch b/target/linux/qualcommax/patches-6.1/0010-v6.2-clk-qcom-ipq8074-add-missing-networking-resets.patch deleted file mode 100644 index 81014ab24c..0000000000 --- a/target/linux/qualcommax/patches-6.1/0010-v6.2-clk-qcom-ipq8074-add-missing-networking-resets.patch +++ /dev/null @@ -1,41 +0,0 @@ -From da76cb63d04dc22ed32123b8c1d084c006d67bfb Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Mon, 7 Nov 2022 14:29:01 +0100 -Subject: [PATCH] clk: qcom: ipq8074: add missing networking resets - -Downstream QCA 5.4 kernel defines networking resets which are not present -in the mainline kernel but are required for the networking drivers. - -So, port the downstream resets and avoid using magic values for mask, -construct mask for resets which require multiple bits to be set/cleared. - -Signed-off-by: Robert Marko -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20221107132901.489240-3-robimarko@gmail.com ---- - drivers/clk/qcom/gcc-ipq8074.c | 14 ++++++++++++++ - 1 file changed, 14 insertions(+) - ---- a/drivers/clk/qcom/gcc-ipq8074.c -+++ b/drivers/clk/qcom/gcc-ipq8074.c -@@ -4665,6 +4665,20 @@ static const struct qcom_reset_map gcc_i - [GCC_PCIE1_AXI_SLAVE_ARES] = { 0x76040, 4 }, - [GCC_PCIE1_AHB_ARES] = { 0x76040, 5 }, - [GCC_PCIE1_AXI_MASTER_STICKY_ARES] = { 0x76040, 6 }, -+ [GCC_PPE_FULL_RESET] = { .reg = 0x68014, .bitmask = GENMASK(19, 16) }, -+ [GCC_UNIPHY0_SOFT_RESET] = { .reg = 0x56004, .bitmask = GENMASK(13, 4) | BIT(1) }, -+ [GCC_UNIPHY0_XPCS_RESET] = { 0x56004, 2 }, -+ [GCC_UNIPHY1_SOFT_RESET] = { .reg = 0x56104, .bitmask = GENMASK(5, 4) | BIT(1) }, -+ [GCC_UNIPHY1_XPCS_RESET] = { 0x56104, 2 }, -+ [GCC_UNIPHY2_SOFT_RESET] = { .reg = 0x56204, .bitmask = GENMASK(5, 4) | BIT(1) }, -+ [GCC_UNIPHY2_XPCS_RESET] = { 0x56204, 2 }, -+ [GCC_EDMA_HW_RESET] = { .reg = 0x68014, .bitmask = GENMASK(21, 20) }, -+ [GCC_NSSPORT1_RESET] = { .reg = 0x68014, .bitmask = BIT(24) | GENMASK(1, 0) }, -+ [GCC_NSSPORT2_RESET] = { .reg = 0x68014, .bitmask = BIT(25) | GENMASK(3, 2) }, -+ [GCC_NSSPORT3_RESET] = { .reg = 0x68014, .bitmask = BIT(26) | GENMASK(5, 4) }, -+ [GCC_NSSPORT4_RESET] = { .reg = 0x68014, .bitmask = BIT(27) | GENMASK(9, 8) }, -+ [GCC_NSSPORT5_RESET] = { .reg = 0x68014, .bitmask = BIT(28) | GENMASK(11, 10) }, -+ [GCC_NSSPORT6_RESET] = { .reg = 0x68014, .bitmask = BIT(29) | GENMASK(13, 12) }, - }; - - static struct gdsc *gcc_ipq8074_gdscs[] = { diff --git a/target/linux/qualcommax/patches-6.1/0011-v6.2-clk-qcom-ipq8074-populate-fw_name-for-all-parents.patch b/target/linux/qualcommax/patches-6.1/0011-v6.2-clk-qcom-ipq8074-populate-fw_name-for-all-parents.patch deleted file mode 100644 index 35a0a07c70..0000000000 --- a/target/linux/qualcommax/patches-6.1/0011-v6.2-clk-qcom-ipq8074-populate-fw_name-for-all-parents.patch +++ /dev/null @@ -1,152 +0,0 @@ -From 78936d46470938caa9a7ea529deeb36777b4f98e Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Wed, 16 Nov 2022 22:46:55 +0100 -Subject: [PATCH] clk: qcom: ipq8074: populate fw_name for all parents - -It appears that having only .name populated in parent_data for clocks -which are only globally searchable currently will not work as the clk core -won't copy that name if there is no .fw_name present as well. - -So, populate .fw_name for all parent clocks in parent_data. - -Fixes: ae55ad32e273 ("clk: qcom: ipq8074: convert to parent data") - -Co-developed-by: Christian Marangi -Signed-off-by: Christian Marangi -Signed-off-by: Robert Marko -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20221116214655.1116467-1-robimarko@gmail.com ---- - drivers/clk/qcom/gcc-ipq8074.c | 52 +++++++++++++++++----------------- - 1 file changed, 26 insertions(+), 26 deletions(-) - ---- a/drivers/clk/qcom/gcc-ipq8074.c -+++ b/drivers/clk/qcom/gcc-ipq8074.c -@@ -674,7 +674,7 @@ static struct clk_rcg2 pcie0_aux_clk_src - }; - - static const struct clk_parent_data gcc_pcie20_phy0_pipe_clk_xo[] = { -- { .name = "pcie20_phy0_pipe_clk" }, -+ { .fw_name = "pcie0_pipe", .name = "pcie20_phy0_pipe_clk" }, - { .fw_name = "xo", .name = "xo" }, - }; - -@@ -727,7 +727,7 @@ static struct clk_rcg2 pcie1_aux_clk_src - }; - - static const struct clk_parent_data gcc_pcie20_phy1_pipe_clk_xo[] = { -- { .name = "pcie20_phy1_pipe_clk" }, -+ { .fw_name = "pcie1_pipe", .name = "pcie20_phy1_pipe_clk" }, - { .fw_name = "xo", .name = "xo" }, - }; - -@@ -1131,7 +1131,7 @@ static const struct freq_tbl ftbl_nss_no - - static const struct clk_parent_data gcc_xo_bias_pll_nss_noc_clk_gpll0_gpll2[] = { - { .fw_name = "xo", .name = "xo" }, -- { .name = "bias_pll_nss_noc_clk" }, -+ { .fw_name = "bias_pll_nss_noc_clk", .name = "bias_pll_nss_noc_clk" }, - { .hw = &gpll0.clkr.hw }, - { .hw = &gpll2.clkr.hw }, - }; -@@ -1356,7 +1356,7 @@ static const struct freq_tbl ftbl_nss_pp - - static const struct clk_parent_data gcc_xo_bias_gpll0_gpll4_nss_ubi32[] = { - { .fw_name = "xo", .name = "xo" }, -- { .name = "bias_pll_cc_clk" }, -+ { .fw_name = "bias_pll_cc_clk", .name = "bias_pll_cc_clk" }, - { .hw = &gpll0.clkr.hw }, - { .hw = &gpll4.clkr.hw }, - { .hw = &nss_crypto_pll.clkr.hw }, -@@ -1407,10 +1407,10 @@ static const struct freq_tbl ftbl_nss_po - - static const struct clk_parent_data gcc_xo_uniphy0_rx_tx_ubi32_bias[] = { - { .fw_name = "xo", .name = "xo" }, -- { .name = "uniphy0_gcc_rx_clk" }, -- { .name = "uniphy0_gcc_tx_clk" }, -+ { .fw_name = "uniphy0_gcc_rx_clk", .name = "uniphy0_gcc_rx_clk" }, -+ { .fw_name = "uniphy0_gcc_tx_clk", .name = "uniphy0_gcc_tx_clk" }, - { .hw = &ubi32_pll.clkr.hw }, -- { .name = "bias_pll_cc_clk" }, -+ { .fw_name = "bias_pll_cc_clk", .name = "bias_pll_cc_clk" }, - }; - - static const struct parent_map gcc_xo_uniphy0_rx_tx_ubi32_bias_map[] = { -@@ -1459,10 +1459,10 @@ static const struct freq_tbl ftbl_nss_po - - static const struct clk_parent_data gcc_xo_uniphy0_tx_rx_ubi32_bias[] = { - { .fw_name = "xo", .name = "xo" }, -- { .name = "uniphy0_gcc_tx_clk" }, -- { .name = "uniphy0_gcc_rx_clk" }, -+ { .fw_name = "uniphy0_gcc_tx_clk", .name = "uniphy0_gcc_tx_clk" }, -+ { .fw_name = "uniphy0_gcc_rx_clk", .name = "uniphy0_gcc_rx_clk" }, - { .hw = &ubi32_pll.clkr.hw }, -- { .name = "bias_pll_cc_clk" }, -+ { .fw_name = "bias_pll_cc_clk", .name = "bias_pll_cc_clk" }, - }; - - static const struct parent_map gcc_xo_uniphy0_tx_rx_ubi32_bias_map[] = { -@@ -1690,12 +1690,12 @@ static const struct freq_tbl ftbl_nss_po - - static const struct clk_parent_data gcc_xo_uniphy0_rx_tx_uniphy1_rx_tx_ubi32_bias[] = { - { .fw_name = "xo", .name = "xo" }, -- { .name = "uniphy0_gcc_rx_clk" }, -- { .name = "uniphy0_gcc_tx_clk" }, -- { .name = "uniphy1_gcc_rx_clk" }, -- { .name = "uniphy1_gcc_tx_clk" }, -+ { .fw_name = "uniphy0_gcc_rx_clk", .name = "uniphy0_gcc_rx_clk" }, -+ { .fw_name = "uniphy0_gcc_tx_clk", .name = "uniphy0_gcc_tx_clk" }, -+ { .fw_name = "uniphy1_gcc_rx_clk", .name = "uniphy1_gcc_rx_clk" }, -+ { .fw_name = "uniphy1_gcc_tx_clk", .name = "uniphy1_gcc_tx_clk" }, - { .hw = &ubi32_pll.clkr.hw }, -- { .name = "bias_pll_cc_clk" }, -+ { .fw_name = "bias_pll_cc_clk", .name = "bias_pll_cc_clk" }, - }; - - static const struct parent_map -@@ -1752,12 +1752,12 @@ static const struct freq_tbl ftbl_nss_po - - static const struct clk_parent_data gcc_xo_uniphy0_tx_rx_uniphy1_tx_rx_ubi32_bias[] = { - { .fw_name = "xo", .name = "xo" }, -- { .name = "uniphy0_gcc_tx_clk" }, -- { .name = "uniphy0_gcc_rx_clk" }, -- { .name = "uniphy1_gcc_tx_clk" }, -- { .name = "uniphy1_gcc_rx_clk" }, -+ { .fw_name = "uniphy0_gcc_tx_clk", .name = "uniphy0_gcc_tx_clk" }, -+ { .fw_name = "uniphy0_gcc_rx_clk", .name = "uniphy0_gcc_rx_clk" }, -+ { .fw_name = "uniphy1_gcc_tx_clk", .name = "uniphy1_gcc_tx_clk" }, -+ { .fw_name = "uniphy1_gcc_rx_clk", .name = "uniphy1_gcc_rx_clk" }, - { .hw = &ubi32_pll.clkr.hw }, -- { .name = "bias_pll_cc_clk" }, -+ { .fw_name = "bias_pll_cc_clk", .name = "bias_pll_cc_clk" }, - }; - - static const struct parent_map -@@ -1814,10 +1814,10 @@ static const struct freq_tbl ftbl_nss_po - - static const struct clk_parent_data gcc_xo_uniphy2_rx_tx_ubi32_bias[] = { - { .fw_name = "xo", .name = "xo" }, -- { .name = "uniphy2_gcc_rx_clk" }, -- { .name = "uniphy2_gcc_tx_clk" }, -+ { .fw_name = "uniphy2_gcc_rx_clk", .name = "uniphy2_gcc_rx_clk" }, -+ { .fw_name = "uniphy2_gcc_tx_clk", .name = "uniphy2_gcc_tx_clk" }, - { .hw = &ubi32_pll.clkr.hw }, -- { .name = "bias_pll_cc_clk" }, -+ { .fw_name = "bias_pll_cc_clk", .name = "bias_pll_cc_clk" }, - }; - - static const struct parent_map gcc_xo_uniphy2_rx_tx_ubi32_bias_map[] = { -@@ -1871,10 +1871,10 @@ static const struct freq_tbl ftbl_nss_po - - static const struct clk_parent_data gcc_xo_uniphy2_tx_rx_ubi32_bias[] = { - { .fw_name = "xo", .name = "xo" }, -- { .name = "uniphy2_gcc_tx_clk" }, -- { .name = "uniphy2_gcc_rx_clk" }, -+ { .fw_name = "uniphy2_gcc_tx_clk", .name = "uniphy2_gcc_tx_clk" }, -+ { .fw_name = "uniphy2_gcc_rx_clk", .name = "uniphy2_gcc_rx_clk" }, - { .hw = &ubi32_pll.clkr.hw }, -- { .name = "bias_pll_cc_clk" }, -+ { .fw_name = "bias_pll_cc_clk", .name = "bias_pll_cc_clk" }, - }; - - static const struct parent_map gcc_xo_uniphy2_tx_rx_ubi32_bias_map[] = { diff --git a/target/linux/qualcommax/patches-6.1/0012-v6.2-arm64-dts-qcom-ipq8074-pass-XO-and-sleep-clocks-to-G.patch b/target/linux/qualcommax/patches-6.1/0012-v6.2-arm64-dts-qcom-ipq8074-pass-XO-and-sleep-clocks-to-G.patch deleted file mode 100644 index 0f3fdfe4d4..0000000000 --- a/target/linux/qualcommax/patches-6.1/0012-v6.2-arm64-dts-qcom-ipq8074-pass-XO-and-sleep-clocks-to-G.patch +++ /dev/null @@ -1,36 +0,0 @@ -From 9033c3c86ea0dd35bd2ab957317573b755967298 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Sun, 30 Oct 2022 18:57:03 +0100 -Subject: [PATCH] arm64: dts: qcom: ipq8074: pass XO and sleep clocks to GCC - -Pass XO and sleep clocks to the GCC controller so it does not have to -find them by matching globaly by name. - -If not passed directly, driver maintains backwards compatibility by then -falling back to global lookup. - -Since we are here, set cell numbers in decimal instead of hex. - -Signed-off-by: Robert Marko -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20221030175703.1103224-3-robimarko@gmail.com ---- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 6 ++++-- - 1 file changed, 4 insertions(+), 2 deletions(-) - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -363,9 +363,11 @@ - gcc: gcc@1800000 { - compatible = "qcom,gcc-ipq8074"; - reg = <0x01800000 0x80000>; -- #clock-cells = <0x1>; -+ clocks = <&xo>, <&sleep_clk>; -+ clock-names = "xo", "sleep_clk"; -+ #clock-cells = <1>; - #power-domain-cells = <1>; -- #reset-cells = <0x1>; -+ #reset-cells = <1>; - }; - - tcsr_mutex: hwlock@1905000 { diff --git a/target/linux/qualcommax/patches-6.1/0013-v6.2-arm64-dts-qcom-add-PMP8074-DTSI.patch b/target/linux/qualcommax/patches-6.1/0013-v6.2-arm64-dts-qcom-add-PMP8074-DTSI.patch deleted file mode 100644 index cd146420cf..0000000000 --- a/target/linux/qualcommax/patches-6.1/0013-v6.2-arm64-dts-qcom-add-PMP8074-DTSI.patch +++ /dev/null @@ -1,149 +0,0 @@ -From fb76b808f8628215afebaf0f8af0bde635302590 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Fri, 19 Aug 2022 00:18:14 +0200 -Subject: [PATCH] arm64: dts: qcom: add PMP8074 DTSI - -PMP8074 is a companion PMIC to the Qualcomm IPQ8074 series that is -controlled via SPMI. - -Add DTSI for it providing GPIO, regulator, RTC and VADC support. - -RTC is disabled by default as there is no built-in battery so it will -loose time unless board vendor added a battery, so make it optional. - -Signed-off-by: Robert Marko -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20220818221815.346233-4-robimarko@gmail.com ---- - arch/arm64/boot/dts/qcom/pmp8074.dtsi | 125 ++++++++++++++++++++++++++ - 1 file changed, 125 insertions(+) - create mode 100644 arch/arm64/boot/dts/qcom/pmp8074.dtsi - ---- /dev/null -+++ b/arch/arm64/boot/dts/qcom/pmp8074.dtsi -@@ -0,0 +1,125 @@ -+// SPDX-License-Identifier: GPL-2.0-only OR BSD-3-Clause -+ -+#include -+#include -+ -+&spmi_bus { -+ pmic@0 { -+ compatible = "qcom,pmp8074", "qcom,spmi-pmic"; -+ reg = <0x0 SPMI_USID>; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ pmp8074_adc: adc@3100 { -+ compatible = "qcom,spmi-adc-rev2"; -+ reg = <0x3100>; -+ interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ #io-channel-cells = <1>; -+ -+ ref-gnd@0 { -+ reg = ; -+ qcom,pre-scaling = <1 1>; -+ }; -+ -+ vref-1p25@1 { -+ reg = ; -+ qcom,pre-scaling = <1 1>; -+ }; -+ -+ vref-vadc@2 { -+ reg = ; -+ qcom,pre-scaling = <1 1>; -+ }; -+ -+ pmic_die: die-temp@6 { -+ reg = ; -+ qcom,pre-scaling = <1 1>; -+ }; -+ -+ xo_therm: xo-temp@76 { -+ reg = ; -+ qcom,ratiometric; -+ qcom,hw-settle-time = <200>; -+ qcom,pre-scaling = <1 1>; -+ }; -+ -+ pa_therm1: thermistor1@77 { -+ reg = ; -+ qcom,ratiometric; -+ qcom,hw-settle-time = <200>; -+ qcom,pre-scaling = <1 1>; -+ }; -+ -+ pa_therm2: thermistor2@78 { -+ reg = ; -+ qcom,ratiometric; -+ qcom,hw-settle-time = <200>; -+ qcom,pre-scaling = <1 1>; -+ }; -+ -+ pa_therm3: thermistor3@79 { -+ reg = ; -+ qcom,ratiometric; -+ qcom,hw-settle-time = <200>; -+ qcom,pre-scaling = <1 1>; -+ }; -+ -+ vph-pwr@131 { -+ reg = ; -+ qcom,pre-scaling = <1 3>; -+ }; -+ }; -+ -+ pmp8074_rtc: rtc@6000 { -+ compatible = "qcom,pm8941-rtc"; -+ reg = <0x6000>; -+ reg-names = "rtc", "alarm"; -+ interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; -+ allow-set-time; -+ status = "disabled"; -+ }; -+ -+ pmp8074_gpios: gpio@c000 { -+ compatible = "qcom,pmp8074-gpio", "qcom,spmi-gpio"; -+ reg = <0xc000>; -+ gpio-controller; -+ #gpio-cells = <2>; -+ gpio-ranges = <&pmp8074_gpios 0 0 12>; -+ interrupt-controller; -+ #interrupt-cells = <2>; -+ }; -+ }; -+ -+ pmic@1 { -+ compatible = "qcom,pmp8074", "qcom,spmi-pmic"; -+ reg = <0x1 SPMI_USID>; -+ -+ regulators { -+ compatible = "qcom,pmp8074-regulators"; -+ -+ s3: s3 { -+ regulator-name = "vdd_s3"; -+ regulator-min-microvolt = <592000>; -+ regulator-max-microvolt = <1064000>; -+ regulator-always-on; -+ regulator-boot-on; -+ }; -+ -+ s4: s4 { -+ regulator-name = "vdd_s4"; -+ regulator-min-microvolt = <712000>; -+ regulator-max-microvolt = <992000>; -+ regulator-always-on; -+ regulator-boot-on; -+ }; -+ -+ l11: l11 { -+ regulator-name = "l11"; -+ regulator-min-microvolt = <1800000>; -+ regulator-max-microvolt = <3300000>; -+ }; -+ }; -+ }; -+}; diff --git a/target/linux/qualcommax/patches-6.1/0014-v6.2-arm64-dts-qcom-ipq8074-hk01-add-VQMMC-supply.patch b/target/linux/qualcommax/patches-6.1/0014-v6.2-arm64-dts-qcom-ipq8074-hk01-add-VQMMC-supply.patch deleted file mode 100644 index ebd3763a58..0000000000 --- a/target/linux/qualcommax/patches-6.1/0014-v6.2-arm64-dts-qcom-ipq8074-hk01-add-VQMMC-supply.patch +++ /dev/null @@ -1,37 +0,0 @@ -From 2c394cfc1779886048feca7dc7f4075da5f6328c Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Fri, 19 Aug 2022 00:18:15 +0200 -Subject: [PATCH] arm64: dts: qcom: ipq8074-hk01: add VQMMC supply - -Since now we have control over the PMP8074 PMIC providing various system -voltages including L11 which provides the SDIO/eMMC I/O voltage set it as -the SDHCI VQMMC supply. - -This allows SDHCI controller to switch to 1.8V I/O mode and support high -speed modes like HS200 and HS400. - -Signed-off-by: Robert Marko -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20220818221815.346233-5-robimarko@gmail.com ---- - arch/arm64/boot/dts/qcom/ipq8074-hk01.dts | 2 ++ - 1 file changed, 2 insertions(+) - ---- a/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts -+++ b/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts -@@ -3,6 +3,7 @@ - /* Copyright (c) 2017, The Linux Foundation. All rights reserved. - */ - #include "ipq8074.dtsi" -+#include "pmp8074.dtsi" - - / { - model = "Qualcomm Technologies, Inc. IPQ8074-HK01"; -@@ -84,6 +85,7 @@ - - &sdhc_1 { - status = "okay"; -+ vqmmc-supply = <&l11>; - }; - - &qusb_phy_0 { diff --git a/target/linux/qualcommax/patches-6.1/0015-v6.2-arm64-dts-qcom-hk01-use-GPIO-flags-for-tlmm.patch b/target/linux/qualcommax/patches-6.1/0015-v6.2-arm64-dts-qcom-hk01-use-GPIO-flags-for-tlmm.patch deleted file mode 100644 index e08f6d1f3c..0000000000 --- a/target/linux/qualcommax/patches-6.1/0015-v6.2-arm64-dts-qcom-hk01-use-GPIO-flags-for-tlmm.patch +++ /dev/null @@ -1,42 +0,0 @@ -From 82ceb86227b1fc15c76d5fc691b2bf425f1a63b3 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Mon, 7 Nov 2022 10:29:30 +0100 -Subject: [PATCH] arm64: dts: qcom: hk01: use GPIO flags for tlmm - -Use respective GPIO_ACTIVE_LOW/HIGH flags for tlmm GPIOs instead of -harcoding the cell value. - -Signed-off-by: Robert Marko -Reviewed-by: Krzysztof Kozlowski -Reviewed-by: Konrad Dybcio -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20221107092930.33325-3-robimarko@gmail.com ---- - arch/arm64/boot/dts/qcom/ipq8074-hk01.dts | 5 +++-- - 1 file changed, 3 insertions(+), 2 deletions(-) - ---- a/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts -+++ b/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts -@@ -4,6 +4,7 @@ - */ - #include "ipq8074.dtsi" - #include "pmp8074.dtsi" -+#include - - / { - model = "Qualcomm Technologies, Inc. IPQ8074-HK01"; -@@ -52,12 +53,12 @@ - - &pcie0 { - status = "okay"; -- perst-gpios = <&tlmm 61 0x1>; -+ perst-gpios = <&tlmm 61 GPIO_ACTIVE_LOW>; - }; - - &pcie1 { - status = "okay"; -- perst-gpios = <&tlmm 58 0x1>; -+ perst-gpios = <&tlmm 58 GPIO_ACTIVE_LOW>; - }; - - &pcie_qmp0 { diff --git a/target/linux/qualcommax/patches-6.1/0016-v6.2-arm64-dts-qcom-ipq8074-Fix-up-comments.patch b/target/linux/qualcommax/patches-6.1/0016-v6.2-arm64-dts-qcom-ipq8074-Fix-up-comments.patch deleted file mode 100644 index a8bf2492f4..0000000000 --- a/target/linux/qualcommax/patches-6.1/0016-v6.2-arm64-dts-qcom-ipq8074-Fix-up-comments.patch +++ /dev/null @@ -1,82 +0,0 @@ -From 1b1c1423ca3e740984aa883512a72c4ea08fbe28 Mon Sep 17 00:00:00 2001 -From: Konrad Dybcio -Date: Mon, 7 Nov 2022 15:55:17 +0100 -Subject: [PATCH] arm64: dts: qcom: ipq8074-*: Fix up comments - -Make sure all multiline C-style commends begin with just '/*' with -the comment text starting on a new line. - -Also, fix up some whitespace within comments. - -Signed-off-by: Konrad Dybcio -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20221107145522.6706-8-konrad.dybcio@linaro.org ---- - arch/arm64/boot/dts/qcom/ipq8074-hk01.dts | 3 ++- - arch/arm64/boot/dts/qcom/ipq8074-hk10-c1.dts | 3 ++- - arch/arm64/boot/dts/qcom/ipq8074-hk10-c2.dts | 3 ++- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 12 ++++++------ - 4 files changed, 12 insertions(+), 9 deletions(-) - ---- a/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts -+++ b/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts -@@ -1,6 +1,7 @@ - // SPDX-License-Identifier: GPL-2.0-only - /dts-v1/; --/* Copyright (c) 2017, The Linux Foundation. All rights reserved. -+/* -+ * Copyright (c) 2017, The Linux Foundation. All rights reserved. - */ - #include "ipq8074.dtsi" - #include "pmp8074.dtsi" ---- a/arch/arm64/boot/dts/qcom/ipq8074-hk10-c1.dts -+++ b/arch/arm64/boot/dts/qcom/ipq8074-hk10-c1.dts -@@ -1,5 +1,6 @@ - // SPDX-License-Identifier: GPL-2.0-only --/* Copyright (c) 2020 The Linux Foundation. All rights reserved. -+/* -+ * Copyright (c) 2020 The Linux Foundation. All rights reserved. - */ - /dts-v1/; - ---- a/arch/arm64/boot/dts/qcom/ipq8074-hk10-c2.dts -+++ b/arch/arm64/boot/dts/qcom/ipq8074-hk10-c2.dts -@@ -1,6 +1,7 @@ - // SPDX-License-Identifier: GPL-2.0-only - /dts-v1/; --/* Copyright (c) 2020 The Linux Foundation. All rights reserved. -+/* -+ * Copyright (c) 2020 The Linux Foundation. All rights reserved. - */ - #include "ipq8074-hk10.dtsi" - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -129,10 +129,10 @@ - status = "disabled"; - - usb1_ssphy: phy@58200 { -- reg = <0x00058200 0x130>, /* Tx */ -+ reg = <0x00058200 0x130>, /* Tx */ - <0x00058400 0x200>, /* Rx */ -- <0x00058800 0x1f8>, /* PCS */ -- <0x00058600 0x044>; /* PCS misc*/ -+ <0x00058800 0x1f8>, /* PCS */ -+ <0x00058600 0x044>; /* PCS misc */ - #phy-cells = <0>; - #clock-cells = <0>; - clocks = <&gcc GCC_USB1_PIPE_CLK>; -@@ -172,10 +172,10 @@ - status = "disabled"; - - usb0_ssphy: phy@78200 { -- reg = <0x00078200 0x130>, /* Tx */ -+ reg = <0x00078200 0x130>, /* Tx */ - <0x00078400 0x200>, /* Rx */ -- <0x00078800 0x1f8>, /* PCS */ -- <0x00078600 0x044>; /* PCS misc*/ -+ <0x00078800 0x1f8>, /* PCS */ -+ <0x00078600 0x044>; /* PCS misc */ - #phy-cells = <0>; - #clock-cells = <0>; - clocks = <&gcc GCC_USB0_PIPE_CLK>; diff --git a/target/linux/qualcommax/patches-6.1/0017-v6.2-arm64-dts-qcom-ipq8074-align-TLMM-pin-configuration-.patch b/target/linux/qualcommax/patches-6.1/0017-v6.2-arm64-dts-qcom-ipq8074-align-TLMM-pin-configuration-.patch deleted file mode 100644 index c9fef2cab4..0000000000 --- a/target/linux/qualcommax/patches-6.1/0017-v6.2-arm64-dts-qcom-ipq8074-align-TLMM-pin-configuration-.patch +++ /dev/null @@ -1,60 +0,0 @@ -From 5f20690f77878b1ba24ec88df01b92d5131a6780 Mon Sep 17 00:00:00 2001 -From: Krzysztof Kozlowski -Date: Tue, 8 Nov 2022 15:23:57 +0100 -Subject: [PATCH] arm64: dts: qcom: ipq8074: align TLMM pin configuration with - DT schema - -DT schema expects TLMM pin configuration nodes to be named with -'-state' suffix and their optional children with '-pins' suffix. - -Signed-off-by: Krzysztof Kozlowski -Reviewed-by: Konrad Dybcio -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20221108142357.67202-2-krzysztof.kozlowski@linaro.org ---- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 10 +++++----- - 1 file changed, 5 insertions(+), 5 deletions(-) - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -320,35 +320,35 @@ - interrupt-controller; - #interrupt-cells = <0x2>; - -- serial_4_pins: serial4-pinmux { -+ serial_4_pins: serial4-state { - pins = "gpio23", "gpio24"; - function = "blsp4_uart1"; - drive-strength = <8>; - bias-disable; - }; - -- i2c_0_pins: i2c-0-pinmux { -+ i2c_0_pins: i2c-0-state { - pins = "gpio42", "gpio43"; - function = "blsp1_i2c"; - drive-strength = <8>; - bias-disable; - }; - -- spi_0_pins: spi-0-pins { -+ spi_0_pins: spi-0-state { - pins = "gpio38", "gpio39", "gpio40", "gpio41"; - function = "blsp0_spi"; - drive-strength = <8>; - bias-disable; - }; - -- hsuart_pins: hsuart-pins { -+ hsuart_pins: hsuart-state { - pins = "gpio46", "gpio47", "gpio48", "gpio49"; - function = "blsp2_uart"; - drive-strength = <8>; - bias-disable; - }; - -- qpic_pins: qpic-pins { -+ qpic_pins: qpic-state { - pins = "gpio1", "gpio3", "gpio4", - "gpio5", "gpio6", "gpio7", - "gpio8", "gpio10", "gpio11", diff --git a/target/linux/qualcommax/patches-6.1/0018-v6.2-arm64-dts-qcom-ipq6018-align-TLMM-pin-configuration-.patch b/target/linux/qualcommax/patches-6.1/0018-v6.2-arm64-dts-qcom-ipq6018-align-TLMM-pin-configuration-.patch deleted file mode 100644 index ceaf68bf7a..0000000000 --- a/target/linux/qualcommax/patches-6.1/0018-v6.2-arm64-dts-qcom-ipq6018-align-TLMM-pin-configuration-.patch +++ /dev/null @@ -1,56 +0,0 @@ -From 20afb6751739264ea41993877de93923911dfdc3 Mon Sep 17 00:00:00 2001 -From: Krzysztof Kozlowski -Date: Thu, 6 Oct 2022 14:46:27 +0200 -Subject: [PATCH] arm64: dts: qcom: ipq6018: align TLMM pin configuration with - DT schema - -DT schema expects TLMM pin configuration nodes to be named with -'-state' suffix and their optional children with '-pins' suffix. - -Signed-off-by: Krzysztof Kozlowski -Reviewed-by: Bjorn Andersson -Reviewed-by: Konrad Dybcio -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20221006124659.217540-3-krzysztof.kozlowski@linaro.org ---- - arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts | 4 ++-- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 4 ++-- - 2 files changed, 4 insertions(+), 4 deletions(-) - ---- a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts -+++ b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts -@@ -51,13 +51,13 @@ - }; - - &tlmm { -- i2c_1_pins: i2c-1-pins { -+ i2c_1_pins: i2c-1-state { - pins = "gpio42", "gpio43"; - function = "blsp2_i2c"; - drive-strength = <8>; - }; - -- spi_0_pins: spi-0-pins { -+ spi_0_pins: spi-0-state { - pins = "gpio38", "gpio39", "gpio40", "gpio41"; - function = "blsp0_spi"; - drive-strength = <8>; ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -218,14 +218,14 @@ - interrupt-controller; - #interrupt-cells = <2>; - -- serial_3_pins: serial3-pinmux { -+ serial_3_pins: serial3-state { - pins = "gpio44", "gpio45"; - function = "blsp2_uart"; - drive-strength = <8>; - bias-pull-down; - }; - -- qpic_pins: qpic-pins { -+ qpic_pins: qpic-state { - pins = "gpio1", "gpio3", "gpio4", - "gpio5", "gpio6", "gpio7", - "gpio8", "gpio10", "gpio11", diff --git a/target/linux/qualcommax/patches-6.1/0019-v6.3-arm64-dts-qcom-ipq8074-set-Gen2-PCIe-pcie-max-link-s.patch b/target/linux/qualcommax/patches-6.1/0019-v6.3-arm64-dts-qcom-ipq8074-set-Gen2-PCIe-pcie-max-link-s.patch deleted file mode 100644 index 2578aa9343..0000000000 --- a/target/linux/qualcommax/patches-6.1/0019-v6.3-arm64-dts-qcom-ipq8074-set-Gen2-PCIe-pcie-max-link-s.patch +++ /dev/null @@ -1,24 +0,0 @@ -From a4748d2850783d36f77ccf2b5fcc86ccf1800ef1 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Wed, 16 Nov 2022 22:48:36 +0100 -Subject: [PATCH] arm64: dts: qcom: ipq8074: set Gen2 PCIe pcie max-link-speed - -Add the generic 'max-link-speed' property to describe the Gen2 PCIe link -generation limit. -This allows the generic DWC code to configure the link speed correctly. - -Signed-off-by: Robert Marko ---- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 1 + - 1 file changed, 1 insertion(+) - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -768,6 +768,7 @@ - linux,pci-domain = <1>; - bus-range = <0x00 0xff>; - num-lanes = <1>; -+ max-link-speed = <2>; - #address-cells = <3>; - #size-cells = <2>; - diff --git a/target/linux/qualcommax/patches-6.1/0020-v6.3-PCI-qcom-Add-support-for-IPQ8074-Gen3-port.patch b/target/linux/qualcommax/patches-6.1/0020-v6.3-PCI-qcom-Add-support-for-IPQ8074-Gen3-port.patch deleted file mode 100644 index 3d5c2182e9..0000000000 --- a/target/linux/qualcommax/patches-6.1/0020-v6.3-PCI-qcom-Add-support-for-IPQ8074-Gen3-port.patch +++ /dev/null @@ -1,26 +0,0 @@ -From f356132229b18ceef5d5ef9103bbaa9bdeb84c8d Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Fri, 13 Jan 2023 17:44:47 +0100 -Subject: [PATCH] PCI: qcom: Add IPQ8074 Gen3 port support - -IPQ8074 has one Gen2 and one Gen3 port, with Gen2 port already supported. -Add compatible for Gen3 port which uses the same controller as IPQ6018. - -Link: https://lore.kernel.org/r/20230113164449.906002-7-robimarko@gmail.com -Signed-off-by: Robert Marko -Signed-off-by: Lorenzo Pieralisi -Signed-off-by: Bjorn Helgaas ---- - drivers/pci/controller/dwc/pcie-qcom.c | 1 + - 1 file changed, 1 insertion(+) - ---- a/drivers/pci/controller/dwc/pcie-qcom.c -+++ b/drivers/pci/controller/dwc/pcie-qcom.c -@@ -1762,6 +1762,7 @@ static const struct of_device_id qcom_pc - { .compatible = "qcom,pcie-ipq8064", .data = &cfg_2_1_0 }, - { .compatible = "qcom,pcie-ipq8064-v2", .data = &cfg_2_1_0 }, - { .compatible = "qcom,pcie-ipq8074", .data = &cfg_2_3_3 }, -+ { .compatible = "qcom,pcie-ipq8074-gen3", .data = &cfg_2_9_0 }, - { .compatible = "qcom,pcie-msm8996", .data = &cfg_2_3_2 }, - { .compatible = "qcom,pcie-qcs404", .data = &cfg_2_4_0 }, - { .compatible = "qcom,pcie-sa8540p", .data = &cfg_1_9_0 }, diff --git a/target/linux/qualcommax/patches-6.1/0021-v6.3-clk-qcom-ipq8074-populate-fw_name-for-usb3phy-s.patch b/target/linux/qualcommax/patches-6.1/0021-v6.3-clk-qcom-ipq8074-populate-fw_name-for-usb3phy-s.patch deleted file mode 100644 index e0e8125ba6..0000000000 --- a/target/linux/qualcommax/patches-6.1/0021-v6.3-clk-qcom-ipq8074-populate-fw_name-for-usb3phy-s.patch +++ /dev/null @@ -1,38 +0,0 @@ -From 614d31c231c7707322b643f409eeb7e28adc7f8c Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Sun, 8 Jan 2023 13:36:28 +0100 -Subject: [PATCH] clk: qcom: ipq8074: populate fw_name for usb3phy-s - -Having only .name populated in parent_data for clocks which are only -globally searchable currently will not work as the clk core won't copy -that name if there is no .fw_name present as well. - -So, populate .fw_name for usb3phy clocks in parent_data as they were -missed by me in ("clk: qcom: ipq8074: populate fw_name for all parents"). - -Fixes: ae55ad32e273 ("clk: qcom: ipq8074: convert to parent data") -Signed-off-by: Robert Marko ---- - drivers/clk/qcom/gcc-ipq8074.c | 4 ++-- - 1 file changed, 2 insertions(+), 2 deletions(-) - ---- a/drivers/clk/qcom/gcc-ipq8074.c -+++ b/drivers/clk/qcom/gcc-ipq8074.c -@@ -928,7 +928,7 @@ static struct clk_rcg2 usb0_mock_utmi_cl - }; - - static const struct clk_parent_data gcc_usb3phy_0_cc_pipe_clk_xo[] = { -- { .name = "usb3phy_0_cc_pipe_clk" }, -+ { .fw_name = "usb3phy_0_cc_pipe_clk", .name = "usb3phy_0_cc_pipe_clk" }, - { .fw_name = "xo", .name = "xo" }, - }; - -@@ -996,7 +996,7 @@ static struct clk_rcg2 usb1_mock_utmi_cl - }; - - static const struct clk_parent_data gcc_usb3phy_1_cc_pipe_clk_xo[] = { -- { .name = "usb3phy_1_cc_pipe_clk" }, -+ { .fw_name = "usb3phy_1_cc_pipe_clk", .name = "usb3phy_1_cc_pipe_clk" }, - { .fw_name = "xo", .name = "xo" }, - }; - diff --git a/target/linux/qualcommax/patches-6.1/0022-v6.4-arm64-dts-qcom-ipq8074-add-compatible-fallback-to.patch b/target/linux/qualcommax/patches-6.1/0022-v6.4-arm64-dts-qcom-ipq8074-add-compatible-fallback-to.patch deleted file mode 100644 index f85be793cd..0000000000 --- a/target/linux/qualcommax/patches-6.1/0022-v6.4-arm64-dts-qcom-ipq8074-add-compatible-fallback-to.patch +++ /dev/null @@ -1,26 +0,0 @@ -From d93bd4630ce163f3761aedc0b342b072bee6db6b Mon Sep 17 00:00:00 2001 -From: Krzysztof Kozlowski -Date: Wed, 22 Mar 2023 18:41:40 +0100 -Subject: [PATCH] arm64: dts: qcom: ipq8074: add compatible fallback to mailbox - -IPQ8074 mailbox is compatible with IPQ6018. - -Signed-off-by: Krzysztof Kozlowski -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20230322174148.810938-4-krzysztof.kozlowski@linaro.org ---- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 3 ++- - 1 file changed, 2 insertions(+), 1 deletion(-) - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -682,7 +682,8 @@ - }; - - apcs_glb: mailbox@b111000 { -- compatible = "qcom,ipq8074-apcs-apps-global"; -+ compatible = "qcom,ipq8074-apcs-apps-global", -+ "qcom,ipq6018-apcs-apps-global"; - reg = <0x0b111000 0x1000>; - clocks = <&a53pll>, <&xo>; - clock-names = "pll", "xo"; diff --git a/target/linux/qualcommax/patches-6.1/0023-v6.5-arm64-dts-qcom-ipq8074-add-critical-thermal-trips.patch b/target/linux/qualcommax/patches-6.1/0023-v6.5-arm64-dts-qcom-ipq8074-add-critical-thermal-trips.patch deleted file mode 100644 index 737bb06752..0000000000 --- a/target/linux/qualcommax/patches-6.1/0023-v6.5-arm64-dts-qcom-ipq8074-add-critical-thermal-trips.patch +++ /dev/null @@ -1,199 +0,0 @@ -From 56d3067cb694ba60d654e7f5ef231b6fabc4697f Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Wed, 7 Jun 2023 20:44:48 +0200 -Subject: [PATCH] arm64: dts: qcom: ipq8074: add critical thermal trips - -According to bindings, thermal zones must have associated trips as well. -Since we currently dont have CPUFreq support and thus no passive cooling -lets start by defining critical trips to protect the devices against -severe overheating. - -Signed-off-by: Robert Marko -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20230607184448.2512179-1-robimarko@gmail.com ---- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 96 +++++++++++++++++++++++++++ - 1 file changed, 96 insertions(+) - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -899,6 +899,14 @@ - polling-delay = <1000>; - - thermal-sensors = <&tsens 4>; -+ -+ trips { -+ nss-top-crit { -+ temperature = <110000>; -+ hysteresis = <1000>; -+ type = "critical"; -+ }; -+ }; - }; - - nss0-thermal { -@@ -906,6 +914,14 @@ - polling-delay = <1000>; - - thermal-sensors = <&tsens 5>; -+ -+ trips { -+ nss-0-crit { -+ temperature = <110000>; -+ hysteresis = <1000>; -+ type = "critical"; -+ }; -+ }; - }; - - nss1-thermal { -@@ -913,6 +929,14 @@ - polling-delay = <1000>; - - thermal-sensors = <&tsens 6>; -+ -+ trips { -+ nss-1-crit { -+ temperature = <110000>; -+ hysteresis = <1000>; -+ type = "critical"; -+ }; -+ }; - }; - - wcss-phya0-thermal { -@@ -920,6 +944,14 @@ - polling-delay = <1000>; - - thermal-sensors = <&tsens 7>; -+ -+ trips { -+ wcss-phya0-crit { -+ temperature = <110000>; -+ hysteresis = <1000>; -+ type = "critical"; -+ }; -+ }; - }; - - wcss-phya1-thermal { -@@ -927,6 +959,14 @@ - polling-delay = <1000>; - - thermal-sensors = <&tsens 8>; -+ -+ trips { -+ wcss-phya1-crit { -+ temperature = <110000>; -+ hysteresis = <1000>; -+ type = "critical"; -+ }; -+ }; - }; - - cpu0_thermal: cpu0-thermal { -@@ -934,6 +974,14 @@ - polling-delay = <1000>; - - thermal-sensors = <&tsens 9>; -+ -+ trips { -+ cpu0-crit { -+ temperature = <110000>; -+ hysteresis = <1000>; -+ type = "critical"; -+ }; -+ }; - }; - - cpu1_thermal: cpu1-thermal { -@@ -941,6 +989,14 @@ - polling-delay = <1000>; - - thermal-sensors = <&tsens 10>; -+ -+ trips { -+ cpu1-crit { -+ temperature = <110000>; -+ hysteresis = <1000>; -+ type = "critical"; -+ }; -+ }; - }; - - cpu2_thermal: cpu2-thermal { -@@ -948,6 +1004,14 @@ - polling-delay = <1000>; - - thermal-sensors = <&tsens 11>; -+ -+ trips { -+ cpu2-crit { -+ temperature = <110000>; -+ hysteresis = <1000>; -+ type = "critical"; -+ }; -+ }; - }; - - cpu3_thermal: cpu3-thermal { -@@ -955,6 +1019,14 @@ - polling-delay = <1000>; - - thermal-sensors = <&tsens 12>; -+ -+ trips { -+ cpu3-crit { -+ temperature = <110000>; -+ hysteresis = <1000>; -+ type = "critical"; -+ }; -+ }; - }; - - cluster_thermal: cluster-thermal { -@@ -962,6 +1034,14 @@ - polling-delay = <1000>; - - thermal-sensors = <&tsens 13>; -+ -+ trips { -+ cluster-crit { -+ temperature = <110000>; -+ hysteresis = <1000>; -+ type = "critical"; -+ }; -+ }; - }; - - wcss-phyb0-thermal { -@@ -969,6 +1049,14 @@ - polling-delay = <1000>; - - thermal-sensors = <&tsens 14>; -+ -+ trips { -+ wcss-phyb0-crit { -+ temperature = <110000>; -+ hysteresis = <1000>; -+ type = "critical"; -+ }; -+ }; - }; - - wcss-phyb1-thermal { -@@ -976,6 +1064,14 @@ - polling-delay = <1000>; - - thermal-sensors = <&tsens 15>; -+ -+ trips { -+ wcss-phyb1-crit { -+ temperature = <110000>; -+ hysteresis = <1000>; -+ type = "critical"; -+ }; -+ }; - }; - }; - }; diff --git a/target/linux/qualcommax/patches-6.1/0024-v6.7-dt-bindings-arm-qcom-ids-Add-IDs-for-IPQ8174-family.patch b/target/linux/qualcommax/patches-6.1/0024-v6.7-dt-bindings-arm-qcom-ids-Add-IDs-for-IPQ8174-family.patch deleted file mode 100644 index 4eb0f097cc..0000000000 --- a/target/linux/qualcommax/patches-6.1/0024-v6.7-dt-bindings-arm-qcom-ids-Add-IDs-for-IPQ8174-family.patch +++ /dev/null @@ -1,29 +0,0 @@ -From 93e161c8f4b9b051e5e746814138cb5520b4b897 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Fri, 1 Sep 2023 20:10:04 +0200 -Subject: [PATCH] dt-bindings: arm: qcom,ids: Add IDs for IPQ8174 family - -IPQ8174 (Oak) family is part of the IPQ8074 family, but the ID-s for it -are missing so lets add them. - -Signed-off-by: Robert Marko -Reviewed-by: Kathiravan T -Acked-by: Conor Dooley -Link: https://lore.kernel.org/r/20230901181041.1538999-1-robimarko@gmail.com -Signed-off-by: Bjorn Andersson ---- - include/dt-bindings/arm/qcom,ids.h | 3 +++ - 1 file changed, 3 insertions(+) - ---- a/include/dt-bindings/arm/qcom,ids.h -+++ b/include/dt-bindings/arm/qcom,ids.h -@@ -121,6 +121,9 @@ - #define QCOM_ID_SM6125 394 - #define QCOM_ID_IPQ8070A 395 - #define QCOM_ID_IPQ8071A 396 -+#define QCOM_ID_IPQ8172 397 -+#define QCOM_ID_IPQ8173 398 -+#define QCOM_ID_IPQ8174 399 - #define QCOM_ID_IPQ6018 402 - #define QCOM_ID_IPQ6028 403 - #define QCOM_ID_IPQ6000 421 diff --git a/target/linux/qualcommax/patches-6.1/0025-v6.7-cpufreq-qcom-nvmem-add-support-for-IPQ6018.patch b/target/linux/qualcommax/patches-6.1/0025-v6.7-cpufreq-qcom-nvmem-add-support-for-IPQ6018.patch deleted file mode 100644 index 63e2f22db7..0000000000 --- a/target/linux/qualcommax/patches-6.1/0025-v6.7-cpufreq-qcom-nvmem-add-support-for-IPQ6018.patch +++ /dev/null @@ -1,123 +0,0 @@ -From 47e161a7873b0891f4e01a69a839f6161d816ea8 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Wed, 25 Oct 2023 14:57:57 +0530 -Subject: [PATCH] cpufreq: qcom-nvmem: add support for IPQ6018 - -IPQ6018 SoC series comes in multiple SKU-s, and not all of them support -high frequency OPP points. - -SoC itself does however have a single bit in QFPROM to indicate the CPU -speed-bin. -That bit is used to indicate frequency limit of 1.5GHz, but that alone is -not enough as IPQ6000 only goes up to 1.2GHz, but SMEM ID can be used to -limit it further. - -IPQ6018 compatible is blacklisted from DT platdev as the cpufreq device -will get created by NVMEM CPUFreq driver. - -Signed-off-by: Robert Marko -[ Viresh: Fixed rebase conflict. ] -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/cpufreq-dt-platdev.c | 1 + - drivers/cpufreq/qcom-cpufreq-nvmem.c | 58 ++++++++++++++++++++++++++++ - 2 files changed, 59 insertions(+) - ---- a/drivers/cpufreq/cpufreq-dt-platdev.c -+++ b/drivers/cpufreq/cpufreq-dt-platdev.c -@@ -163,6 +163,7 @@ static const struct of_device_id blockli - { .compatible = "ti,dra7", }, - { .compatible = "ti,omap3", }, - -+ { .compatible = "qcom,ipq6018", }, - { .compatible = "qcom,ipq8064", }, - { .compatible = "qcom,apq8064", }, - { .compatible = "qcom,msm8974", }, ---- a/drivers/cpufreq/qcom-cpufreq-nvmem.c -+++ b/drivers/cpufreq/qcom-cpufreq-nvmem.c -@@ -31,6 +31,8 @@ - - #include - -+#define IPQ6000_VERSION BIT(2) -+ - struct qcom_cpufreq_drv; - - struct qcom_cpufreq_match_data { -@@ -204,6 +206,57 @@ len_error: - return ret; - } - -+static int qcom_cpufreq_ipq6018_name_version(struct device *cpu_dev, -+ struct nvmem_cell *speedbin_nvmem, -+ char **pvs_name, -+ struct qcom_cpufreq_drv *drv) -+{ -+ u32 msm_id; -+ int ret; -+ u8 *speedbin; -+ *pvs_name = NULL; -+ -+ ret = qcom_smem_get_soc_id(&msm_id); -+ if (ret) -+ return ret; -+ -+ speedbin = nvmem_cell_read(speedbin_nvmem, NULL); -+ if (IS_ERR(speedbin)) -+ return PTR_ERR(speedbin); -+ -+ switch (msm_id) { -+ case QCOM_ID_IPQ6005: -+ case QCOM_ID_IPQ6010: -+ case QCOM_ID_IPQ6018: -+ case QCOM_ID_IPQ6028: -+ /* Fuse Value Freq BIT to set -+ * --------------------------------- -+ * 2’b0 No Limit BIT(0) -+ * 2’b1 1.5 GHz BIT(1) -+ */ -+ drv->versions = 1 << (unsigned int)(*speedbin); -+ break; -+ case QCOM_ID_IPQ6000: -+ /* -+ * IPQ6018 family only has one bit to advertise the CPU -+ * speed-bin, but that is not enough for IPQ6000 which -+ * is only rated up to 1.2GHz. -+ * So for IPQ6000 manually set BIT(2) based on SMEM ID. -+ */ -+ drv->versions = IPQ6000_VERSION; -+ break; -+ default: -+ dev_err(cpu_dev, -+ "SoC ID %u is not part of IPQ6018 family, limiting to 1.2GHz!\n", -+ msm_id); -+ drv->versions = IPQ6000_VERSION; -+ break; -+ } -+ -+ kfree(speedbin); -+ return 0; -+} -+ - static const struct qcom_cpufreq_match_data match_data_kryo = { - .get_version = qcom_cpufreq_kryo_name_version, - }; -@@ -218,6 +271,10 @@ static const struct qcom_cpufreq_match_d - .genpd_names = qcs404_genpd_names, - }; - -+static const struct qcom_cpufreq_match_data match_data_ipq6018 = { -+ .get_version = qcom_cpufreq_ipq6018_name_version, -+}; -+ - static int qcom_cpufreq_probe(struct platform_device *pdev) - { - struct qcom_cpufreq_drv *drv; -@@ -362,6 +419,7 @@ static const struct of_device_id qcom_cp - { .compatible = "qcom,apq8096", .data = &match_data_kryo }, - { .compatible = "qcom,msm8996", .data = &match_data_kryo }, - { .compatible = "qcom,qcs404", .data = &match_data_qcs404 }, -+ { .compatible = "qcom,ipq6018", .data = &match_data_ipq6018 }, - { .compatible = "qcom,ipq8064", .data = &match_data_krait }, - { .compatible = "qcom,apq8064", .data = &match_data_krait }, - { .compatible = "qcom,msm8974", .data = &match_data_krait }, diff --git a/target/linux/qualcommax/patches-6.1/0026-v6.7-cpufreq-qcom-nvmem-add-support-for-IPQ8074.patch b/target/linux/qualcommax/patches-6.1/0026-v6.7-cpufreq-qcom-nvmem-add-support-for-IPQ8074.patch deleted file mode 100644 index cbd7b770f4..0000000000 --- a/target/linux/qualcommax/patches-6.1/0026-v6.7-cpufreq-qcom-nvmem-add-support-for-IPQ8074.patch +++ /dev/null @@ -1,113 +0,0 @@ -From 0b9cd949136f1b63f7aa9424b6e583a1ab261e36 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Fri, 13 Oct 2023 19:20:02 +0200 -Subject: [PATCH] cpufreq: qcom-nvmem: add support for IPQ8074 - -IPQ8074 comes in 3 families: -* IPQ8070A/IPQ8071A (Acorn) up to 1.4GHz -* IPQ8172/IPQ8173/IPQ8174 (Oak) up to 1.4GHz -* IPQ8072A/IPQ8074A/IPQ8076A/IPQ8078A (Hawkeye) up to 2.2GHz - -So, in order to be able to share one OPP table lets add support for IPQ8074 -family based of SMEM SoC ID-s as speedbin fuse is always 0 on IPQ8074. - -IPQ8074 compatible is blacklisted from DT platdev as the cpufreq device -will get created by NVMEM CPUFreq driver. - -Signed-off-by: Robert Marko -Acked-by: Konrad Dybcio -[ Viresh: Fixed rebase conflict. ] -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/cpufreq-dt-platdev.c | 1 + - drivers/cpufreq/qcom-cpufreq-nvmem.c | 48 ++++++++++++++++++++++++++++ - 2 files changed, 49 insertions(+) - ---- a/drivers/cpufreq/cpufreq-dt-platdev.c -+++ b/drivers/cpufreq/cpufreq-dt-platdev.c -@@ -165,6 +165,7 @@ static const struct of_device_id blockli - - { .compatible = "qcom,ipq6018", }, - { .compatible = "qcom,ipq8064", }, -+ { .compatible = "qcom,ipq8074", }, - { .compatible = "qcom,apq8064", }, - { .compatible = "qcom,msm8974", }, - { .compatible = "qcom,msm8960", }, ---- a/drivers/cpufreq/qcom-cpufreq-nvmem.c -+++ b/drivers/cpufreq/qcom-cpufreq-nvmem.c -@@ -33,6 +33,11 @@ - - #define IPQ6000_VERSION BIT(2) - -+enum ipq8074_versions { -+ IPQ8074_HAWKEYE_VERSION = 0, -+ IPQ8074_ACORN_VERSION, -+}; -+ - struct qcom_cpufreq_drv; - - struct qcom_cpufreq_match_data { -@@ -257,6 +262,44 @@ static int qcom_cpufreq_ipq6018_name_ver - return 0; - } - -+static int qcom_cpufreq_ipq8074_name_version(struct device *cpu_dev, -+ struct nvmem_cell *speedbin_nvmem, -+ char **pvs_name, -+ struct qcom_cpufreq_drv *drv) -+{ -+ u32 msm_id; -+ int ret; -+ *pvs_name = NULL; -+ -+ ret = qcom_smem_get_soc_id(&msm_id); -+ if (ret) -+ return ret; -+ -+ switch (msm_id) { -+ case QCOM_ID_IPQ8070A: -+ case QCOM_ID_IPQ8071A: -+ case QCOM_ID_IPQ8172: -+ case QCOM_ID_IPQ8173: -+ case QCOM_ID_IPQ8174: -+ drv->versions = BIT(IPQ8074_ACORN_VERSION); -+ break; -+ case QCOM_ID_IPQ8072A: -+ case QCOM_ID_IPQ8074A: -+ case QCOM_ID_IPQ8076A: -+ case QCOM_ID_IPQ8078A: -+ drv->versions = BIT(IPQ8074_HAWKEYE_VERSION); -+ break; -+ default: -+ dev_err(cpu_dev, -+ "SoC ID %u is not part of IPQ8074 family, limiting to 1.4GHz!\n", -+ msm_id); -+ drv->versions = BIT(IPQ8074_ACORN_VERSION); -+ break; -+ } -+ -+ return 0; -+} -+ - static const struct qcom_cpufreq_match_data match_data_kryo = { - .get_version = qcom_cpufreq_kryo_name_version, - }; -@@ -275,6 +318,10 @@ static const struct qcom_cpufreq_match_d - .get_version = qcom_cpufreq_ipq6018_name_version, - }; - -+static const struct qcom_cpufreq_match_data match_data_ipq8074 = { -+ .get_version = qcom_cpufreq_ipq8074_name_version, -+}; -+ - static int qcom_cpufreq_probe(struct platform_device *pdev) - { - struct qcom_cpufreq_drv *drv; -@@ -421,6 +468,7 @@ static const struct of_device_id qcom_cp - { .compatible = "qcom,qcs404", .data = &match_data_qcs404 }, - { .compatible = "qcom,ipq6018", .data = &match_data_ipq6018 }, - { .compatible = "qcom,ipq8064", .data = &match_data_krait }, -+ { .compatible = "qcom,ipq8074", .data = &match_data_ipq8074 }, - { .compatible = "qcom,apq8064", .data = &match_data_krait }, - { .compatible = "qcom,msm8974", .data = &match_data_krait }, - { .compatible = "qcom,msm8960", .data = &match_data_krait }, diff --git a/target/linux/qualcommax/patches-6.1/0027-v6.7-clk-qcom-apss-ipq6018-add-the-GPLL0-clock-also-as-cl.patch b/target/linux/qualcommax/patches-6.1/0027-v6.7-clk-qcom-apss-ipq6018-add-the-GPLL0-clock-also-as-cl.patch deleted file mode 100644 index ddd53f9d42..0000000000 --- a/target/linux/qualcommax/patches-6.1/0027-v6.7-clk-qcom-apss-ipq6018-add-the-GPLL0-clock-also-as-cl.patch +++ /dev/null @@ -1,43 +0,0 @@ -From c917237a7cb17b97cc48e073881a9873f3caeaa2 Mon Sep 17 00:00:00 2001 -From: Kathiravan Thirumoorthy -Date: Thu, 14 Sep 2023 12:29:57 +0530 -Subject: [PATCH] clk: qcom: apss-ipq6018: add the GPLL0 clock also as clock - provider - -While the kernel is booting up, APSS PLL will be running at 800MHz with -GPLL0 as source. Once the cpufreq driver is available, APSS PLL will be -configured and select the rate based on the opp table and the source will -be changed to APSS_PLL_EARLY. - -Without this patch, CPU Freq driver reports that CPU is running at 24MHz -instead of the 800MHz. - -Reviewed-by: Konrad Dybcio -Tested-by: Robert Marko -Signed-off-by: Kathiravan Thirumoorthy ---- - drivers/clk/qcom/apss-ipq6018.c | 3 +++ - 1 file changed, 3 insertions(+) - ---- a/drivers/clk/qcom/apss-ipq6018.c -+++ b/drivers/clk/qcom/apss-ipq6018.c -@@ -20,16 +20,19 @@ - - enum { - P_XO, -+ P_GPLL0, - P_APSS_PLL_EARLY, - }; - - static const struct clk_parent_data parents_apcs_alias0_clk_src[] = { - { .fw_name = "xo" }, -+ { .fw_name = "gpll0" }, - { .fw_name = "pll" }, - }; - - static const struct parent_map parents_apcs_alias0_clk_src_map[] = { - { P_XO, 0 }, -+ { P_GPLL0, 4 }, - { P_APSS_PLL_EARLY, 5 }, - }; - diff --git a/target/linux/qualcommax/patches-6.1/0028-v6.7-arm64-dts-qcom-ipq8074-include-the-GPLL0-as-clock-pr.patch b/target/linux/qualcommax/patches-6.1/0028-v6.7-arm64-dts-qcom-ipq8074-include-the-GPLL0-as-clock-pr.patch deleted file mode 100644 index fb7011de95..0000000000 --- a/target/linux/qualcommax/patches-6.1/0028-v6.7-arm64-dts-qcom-ipq8074-include-the-GPLL0-as-clock-pr.patch +++ /dev/null @@ -1,32 +0,0 @@ -From 3b48a7d925a757b3fa53c04baaf68bb8313c3ffb Mon Sep 17 00:00:00 2001 -From: Kathiravan Thirumoorthy -Date: Thu, 14 Sep 2023 12:29:58 +0530 -Subject: [PATCH] arm64: dts: qcom: ipq8074: include the GPLL0 as clock - provider for mailbox - -While the kernel is booting up, APSS PLL will be running at 800MHz with -GPLL0 as source. Once the cpufreq driver is available, APSS PLL will be -configured to the rate based on the opp table and the source also will -be changed to APSS_PLL_EARLY. So allow the mailbox to consume the GPLL0, -with this inclusion, CPU Freq correctly reports that CPU is running at -800MHz rather than 24MHz. - -Signed-off-by: Kathiravan Thirumoorthy -Reviewed-by: Konrad Dybcio ---- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 4 ++-- - 1 file changed, 2 insertions(+), 2 deletions(-) - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -685,8 +685,8 @@ - compatible = "qcom,ipq8074-apcs-apps-global", - "qcom,ipq6018-apcs-apps-global"; - reg = <0x0b111000 0x1000>; -- clocks = <&a53pll>, <&xo>; -- clock-names = "pll", "xo"; -+ clocks = <&a53pll>, <&xo>, <&gcc GPLL0>; -+ clock-names = "pll", "xo", "gpll0"; - - #clock-cells = <1>; - #mbox-cells = <1>; diff --git a/target/linux/qualcommax/patches-6.1/0029-v6.3-dt-bindings-arm-qcom-ids-Add-IDs-for-IPQ5332-and-its.patch b/target/linux/qualcommax/patches-6.1/0029-v6.3-dt-bindings-arm-qcom-ids-Add-IDs-for-IPQ5332-and-its.patch deleted file mode 100644 index 61bb3f6c37..0000000000 --- a/target/linux/qualcommax/patches-6.1/0029-v6.3-dt-bindings-arm-qcom-ids-Add-IDs-for-IPQ5332-and-its.patch +++ /dev/null @@ -1,27 +0,0 @@ -From c0877a26b7ee54ef30d16ffdcdd37f2bcffe518e Mon Sep 17 00:00:00 2001 -From: Kathiravan T -Date: Wed, 8 Feb 2023 11:27:08 +0530 -Subject: [PATCH] dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its - variant - -Add SOC ID for Qualcomm IPQ5332 and IPQ5322 variants. - -Signed-off-by: Kathiravan T -Acked-by: Krzysztof Kozlowski -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20230208055709.13162-2-quic_kathirav@quicinc.com ---- - include/dt-bindings/arm/qcom,ids.h | 2 ++ - 1 file changed, 2 insertions(+) - ---- a/include/dt-bindings/arm/qcom,ids.h -+++ b/include/dt-bindings/arm/qcom,ids.h -@@ -143,6 +143,8 @@ - #define QCOM_ID_SC7280 487 - #define QCOM_ID_SC7180P 495 - #define QCOM_ID_SM6375 507 -+#define QCOM_ID_IPQ5332 592 -+#define QCOM_ID_IPQ5322 593 - - /* - * The board type and revision information, used by Qualcomm bootloaders and diff --git a/target/linux/qualcommax/patches-6.1/0030-v6.4-dt-bindings-arm-qcom-ids-Add-IDs-for-IPQ9574-and-its.patch b/target/linux/qualcommax/patches-6.1/0030-v6.4-dt-bindings-arm-qcom-ids-Add-IDs-for-IPQ9574-and-its.patch deleted file mode 100644 index 7d80e4c1fd..0000000000 --- a/target/linux/qualcommax/patches-6.1/0030-v6.4-dt-bindings-arm-qcom-ids-Add-IDs-for-IPQ9574-and-its.patch +++ /dev/null @@ -1,33 +0,0 @@ -From 725352e15e1d030885611a546eb1f2884851a407 Mon Sep 17 00:00:00 2001 -From: Varadarajan Narayanan -Date: Tue, 14 Mar 2023 11:43:33 +0530 -Subject: [PATCH] dt-bindings: arm: qcom,ids: Add IDs for IPQ9574 and its - variants - -Add SOC ID for Qualcomm IPQ9574, IPQ9570, IPQ9554, IPQ9550, -IPQ9514 and IPQ9510 - -Signed-off-by: Varadarajan Narayanan -Acked-by: Krzysztof Kozlowski -Reviewed-by: Kathiravan T -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/1678774414-14414-2-git-send-email-quic_varada@quicinc.com ---- - include/dt-bindings/arm/qcom,ids.h | 6 ++++++ - 1 file changed, 6 insertions(+) - ---- a/include/dt-bindings/arm/qcom,ids.h -+++ b/include/dt-bindings/arm/qcom,ids.h -@@ -143,6 +143,12 @@ - #define QCOM_ID_SC7280 487 - #define QCOM_ID_SC7180P 495 - #define QCOM_ID_SM6375 507 -+#define QCOM_ID_IPQ9514 510 -+#define QCOM_ID_IPQ9550 511 -+#define QCOM_ID_IPQ9554 512 -+#define QCOM_ID_IPQ9570 513 -+#define QCOM_ID_IPQ9574 514 -+#define QCOM_ID_IPQ9510 521 - #define QCOM_ID_IPQ5332 592 - #define QCOM_ID_IPQ5322 593 - diff --git a/target/linux/qualcommax/patches-6.1/0031-v6.5-dt-bindings-arm-qcom-ids-add-SoC-ID-for-IPQ5312-and-.patch b/target/linux/qualcommax/patches-6.1/0031-v6.5-dt-bindings-arm-qcom-ids-add-SoC-ID-for-IPQ5312-and-.patch deleted file mode 100644 index ad70e7b6c9..0000000000 --- a/target/linux/qualcommax/patches-6.1/0031-v6.5-dt-bindings-arm-qcom-ids-add-SoC-ID-for-IPQ5312-and-.patch +++ /dev/null @@ -1,28 +0,0 @@ -From 614c778cf0d570642c50715adfa0b70930d8cf29 Mon Sep 17 00:00:00 2001 -From: Kathiravan T -Date: Tue, 9 May 2023 09:05:30 +0530 -Subject: [PATCH] dt-bindings: arm: qcom,ids: add SoC ID for IPQ5312 and - IPQ5302 - -Add the SoC ID for IPQ5312 and IPQ5302, which belong to the family of -IPQ5332 SoC. - -Reviewed-by: Krzysztof Kozlowski -Signed-off-by: Kathiravan T -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20230509033531.21468-2-quic_kathirav@quicinc.com ---- - include/dt-bindings/arm/qcom,ids.h | 2 ++ - 1 file changed, 2 insertions(+) - ---- a/include/dt-bindings/arm/qcom,ids.h -+++ b/include/dt-bindings/arm/qcom,ids.h -@@ -151,6 +151,8 @@ - #define QCOM_ID_IPQ9510 521 - #define QCOM_ID_IPQ5332 592 - #define QCOM_ID_IPQ5322 593 -+#define QCOM_ID_IPQ5312 594 -+#define QCOM_ID_IPQ5302 595 - - /* - * The board type and revision information, used by Qualcomm bootloaders and diff --git a/target/linux/qualcommax/patches-6.1/0032-v6.5-dt-bindings-arm-qcom-ids-add-SoC-ID-for-IPQ5300.patch b/target/linux/qualcommax/patches-6.1/0032-v6.5-dt-bindings-arm-qcom-ids-add-SoC-ID-for-IPQ5300.patch deleted file mode 100644 index 7925a0994d..0000000000 --- a/target/linux/qualcommax/patches-6.1/0032-v6.5-dt-bindings-arm-qcom-ids-add-SoC-ID-for-IPQ5300.patch +++ /dev/null @@ -1,25 +0,0 @@ -From b3c72f2795467e3d43ee429b0ebd5f523ec08f60 Mon Sep 17 00:00:00 2001 -From: Kathiravan T -Date: Mon, 5 Jun 2023 13:35:28 +0530 -Subject: [PATCH] dt-bindings: arm: qcom,ids: add SoC ID for IPQ5300 - -Add the SoC ID for IPQ5300, which belong to the family of IPQ5332 SoC. - -Acked-by: Krzysztof Kozlowski -Signed-off-by: Kathiravan T -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20230605080531.3879-2-quic_kathirav@quicinc.com ---- - include/dt-bindings/arm/qcom,ids.h | 1 + - 1 file changed, 1 insertion(+) - ---- a/include/dt-bindings/arm/qcom,ids.h -+++ b/include/dt-bindings/arm/qcom,ids.h -@@ -153,6 +153,7 @@ - #define QCOM_ID_IPQ5322 593 - #define QCOM_ID_IPQ5312 594 - #define QCOM_ID_IPQ5302 595 -+#define QCOM_ID_IPQ5300 624 - - /* - * The board type and revision information, used by Qualcomm bootloaders and diff --git a/target/linux/qualcommax/patches-6.1/0033-v6.2-arm64-dts-qcom-ipq6018-move-ARMv8-timer-out-of-SoC.patch b/target/linux/qualcommax/patches-6.1/0033-v6.2-arm64-dts-qcom-ipq6018-move-ARMv8-timer-out-of-SoC.patch deleted file mode 100644 index c3e94a2ae0..0000000000 --- a/target/linux/qualcommax/patches-6.1/0033-v6.2-arm64-dts-qcom-ipq6018-move-ARMv8-timer-out-of-SoC.patch +++ /dev/null @@ -1,52 +0,0 @@ -From feeef118fda562cf9081edef8ad464d89db070f4 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Tue, 27 Sep 2022 22:12:18 +0200 -Subject: [PATCH] arm64: dts: qcom: ipq6018: move ARMv8 timer out of SoC node - -The ARM timer is usually considered not part of SoC node, just like -other ARM designed blocks (PMU, PSCI). This fixes dtbs_check warning: - -arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dtb: soc: timer: {'compatible': ['arm,armv8-timer'], 'interrupts': [[1, 2, 3848], [1, 3, 3848], [1, 4, 3848], [1, 1, 3848]]} should not be valid under {'type': 'object'} - From schema: dtschema/schemas/simple-bus.yaml - -Signed-off-by: Robert Marko -Reviewed-by: Krzysztof Kozlowski -Reviewed-by: Neil Armstrong -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20220927201218.1264506-2-robimarko@gmail.com ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 16 ++++++++-------- - 1 file changed, 8 insertions(+), 8 deletions(-) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -510,14 +510,6 @@ - clock-names = "xo"; - }; - -- timer { -- compatible = "arm,armv8-timer"; -- interrupts = , -- , -- , -- ; -- }; -- - timer@b120000 { - #address-cells = <1>; - #size-cells = <1>; -@@ -769,6 +761,14 @@ - }; - }; - -+ timer { -+ compatible = "arm,armv8-timer"; -+ interrupts = , -+ , -+ , -+ ; -+ }; -+ - wcss: wcss-smp2p { - compatible = "qcom,smp2p"; - qcom,smem = <435>, <428>; diff --git a/target/linux/qualcommax/patches-6.1/0034-v6.3-arm64-dts-qcom-ipq6018-Sort-nodes-properly.patch b/target/linux/qualcommax/patches-6.1/0034-v6.3-arm64-dts-qcom-ipq6018-Sort-nodes-properly.patch deleted file mode 100644 index ad32e64fe1..0000000000 --- a/target/linux/qualcommax/patches-6.1/0034-v6.3-arm64-dts-qcom-ipq6018-Sort-nodes-properly.patch +++ /dev/null @@ -1,605 +0,0 @@ -From 2c6e322a41c5e1ca45be50b9d5fbcda62dc23a0d Mon Sep 17 00:00:00 2001 -From: Konrad Dybcio -Date: Mon, 2 Jan 2023 10:46:28 +0100 -Subject: [PATCH] arm64: dts: qcom: ipq6018: Sort nodes properly - -Order nodes by unit address if one exists and alphabetically otherwise. - -Signed-off-by: Konrad Dybcio -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20230102094642.74254-4-konrad.dybcio@linaro.org ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 562 +++++++++++++------------- - 1 file changed, 281 insertions(+), 281 deletions(-) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -87,6 +87,12 @@ - }; - }; - -+ firmware { -+ scm { -+ compatible = "qcom,scm-ipq6018", "qcom,scm"; -+ }; -+ }; -+ - cpu_opp_table: opp-table-cpu { - compatible = "operating-points-v2"; - opp-shared; -@@ -123,12 +129,6 @@ - }; - }; - -- firmware { -- scm { -- compatible = "qcom,scm-ipq6018", "qcom,scm"; -- }; -- }; -- - pmuv8: pmu { - compatible = "arm,cortex-a53-pmu"; - interrupts = ; -+ qcom,rpm-msg-ram = <&rpm_msg_ram>; -+ mboxes = <&apcs_glb 0>; -+ -+ rpm_requests: glink-channel { -+ compatible = "qcom,rpm-ipq6018"; -+ qcom,glink-channels = "rpm_requests"; -+ -+ regulators { -+ compatible = "qcom,rpm-mp5496-regulators"; -+ -+ ipq6018_s2: s2 { -+ regulator-min-microvolt = <725000>; -+ regulator-max-microvolt = <1062500>; -+ regulator-always-on; -+ }; -+ }; -+ }; -+ }; -+ - smem { - compatible = "qcom,smem"; - memory-region = <&smem_region>; -@@ -179,6 +201,102 @@ - dma-ranges; - compatible = "simple-bus"; - -+ qusb_phy_1: qusb@59000 { -+ compatible = "qcom,ipq6018-qusb2-phy"; -+ reg = <0x0 0x00059000 0x0 0x180>; -+ #phy-cells = <0>; -+ -+ clocks = <&gcc GCC_USB1_PHY_CFG_AHB_CLK>, -+ <&xo>; -+ clock-names = "cfg_ahb", "ref"; -+ -+ resets = <&gcc GCC_QUSB2_1_PHY_BCR>; -+ status = "disabled"; -+ }; -+ -+ ssphy_0: ssphy@78000 { -+ compatible = "qcom,ipq6018-qmp-usb3-phy"; -+ reg = <0x0 0x00078000 0x0 0x1c4>; -+ #address-cells = <2>; -+ #size-cells = <2>; -+ ranges; -+ -+ clocks = <&gcc GCC_USB0_AUX_CLK>, -+ <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, <&xo>; -+ clock-names = "aux", "cfg_ahb", "ref"; -+ -+ resets = <&gcc GCC_USB0_PHY_BCR>, -+ <&gcc GCC_USB3PHY_0_PHY_BCR>; -+ reset-names = "phy","common"; -+ status = "disabled"; -+ -+ usb0_ssphy: phy@78200 { -+ reg = <0x0 0x00078200 0x0 0x130>, /* Tx */ -+ <0x0 0x00078400 0x0 0x200>, /* Rx */ -+ <0x0 0x00078800 0x0 0x1f8>, /* PCS */ -+ <0x0 0x00078600 0x0 0x044>; /* PCS misc */ -+ #phy-cells = <0>; -+ #clock-cells = <0>; -+ clocks = <&gcc GCC_USB0_PIPE_CLK>; -+ clock-names = "pipe0"; -+ clock-output-names = "gcc_usb0_pipe_clk_src"; -+ }; -+ }; -+ -+ qusb_phy_0: qusb@79000 { -+ compatible = "qcom,ipq6018-qusb2-phy"; -+ reg = <0x0 0x00079000 0x0 0x180>; -+ #phy-cells = <0>; -+ -+ clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, -+ <&xo>; -+ clock-names = "cfg_ahb", "ref"; -+ -+ resets = <&gcc GCC_QUSB2_0_PHY_BCR>; -+ status = "disabled"; -+ }; -+ -+ pcie_phy: phy@84000 { -+ compatible = "qcom,ipq6018-qmp-pcie-phy"; -+ reg = <0x0 0x00084000 0x0 0x1bc>; /* Serdes PLL */ -+ status = "disabled"; -+ #address-cells = <2>; -+ #size-cells = <2>; -+ ranges; -+ -+ clocks = <&gcc GCC_PCIE0_AUX_CLK>, -+ <&gcc GCC_PCIE0_AHB_CLK>; -+ clock-names = "aux", "cfg_ahb"; -+ -+ resets = <&gcc GCC_PCIE0_PHY_BCR>, -+ <&gcc GCC_PCIE0PHY_PHY_BCR>; -+ reset-names = "phy", -+ "common"; -+ -+ pcie_phy0: phy@84200 { -+ reg = <0x0 0x00084200 0x0 0x16c>, /* Serdes Tx */ -+ <0x0 0x00084400 0x0 0x200>, /* Serdes Rx */ -+ <0x0 0x00084800 0x0 0x1f0>, /* PCS: Lane0, COM, PCIE */ -+ <0x0 0x00084c00 0x0 0xf4>; /* pcs_misc */ -+ #phy-cells = <0>; -+ -+ clocks = <&gcc GCC_PCIE0_PIPE_CLK>; -+ clock-names = "pipe0"; -+ clock-output-names = "gcc_pcie0_pipe_clk_src"; -+ #clock-cells = <0>; -+ }; -+ }; -+ -+ mdio: mdio@90000 { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ compatible = "qcom,ipq6018-mdio", "qcom,ipq4019-mdio"; -+ reg = <0x0 0x00090000 0x0 0x64>; -+ clocks = <&gcc GCC_MDIO_AHB_CLK>; -+ clock-names = "gcc_mdio_ahb_clk"; -+ status = "disabled"; -+ }; -+ - prng: qrng@e1000 { - compatible = "qcom,prng-ee"; - reg = <0x0 0x000e3000 0x0 0x1000>; -@@ -257,6 +375,41 @@ - reg = <0x0 0x01937000 0x0 0x21000>; - }; - -+ usb2: usb@70f8800 { -+ compatible = "qcom,ipq6018-dwc3", "qcom,dwc3"; -+ reg = <0x0 0x070F8800 0x0 0x400>; -+ #address-cells = <2>; -+ #size-cells = <2>; -+ ranges; -+ clocks = <&gcc GCC_USB1_MASTER_CLK>, -+ <&gcc GCC_USB1_SLEEP_CLK>, -+ <&gcc GCC_USB1_MOCK_UTMI_CLK>; -+ clock-names = "core", -+ "sleep", -+ "mock_utmi"; -+ -+ assigned-clocks = <&gcc GCC_USB1_MASTER_CLK>, -+ <&gcc GCC_USB1_MOCK_UTMI_CLK>; -+ assigned-clock-rates = <133330000>, -+ <24000000>; -+ resets = <&gcc GCC_USB1_BCR>; -+ status = "disabled"; -+ -+ dwc_1: usb@7000000 { -+ compatible = "snps,dwc3"; -+ reg = <0x0 0x07000000 0x0 0xcd00>; -+ interrupts = ; -+ phys = <&qusb_phy_1>; -+ phy-names = "usb2-phy"; -+ tx-fifo-resize; -+ snps,is-utmi-l1-suspend; -+ snps,hird-threshold = /bits/ 8 <0x0>; -+ snps,dis_u2_susphy_quirk; -+ snps,dis_u3_susphy_quirk; -+ dr_mode = "host"; -+ }; -+ }; -+ - blsp_dma: dma-controller@7884000 { - compatible = "qcom,bam-v1.7.0"; - reg = <0x0 0x07884000 0x0 0x2b000>; -@@ -366,6 +519,49 @@ - status = "disabled"; - }; - -+ usb3: usb@8af8800 { -+ compatible = "qcom,ipq6018-dwc3", "qcom,dwc3"; -+ reg = <0x0 0x08af8800 0x0 0x400>; -+ #address-cells = <2>; -+ #size-cells = <2>; -+ ranges; -+ -+ clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>, -+ <&gcc GCC_USB0_MASTER_CLK>, -+ <&gcc GCC_USB0_SLEEP_CLK>, -+ <&gcc GCC_USB0_MOCK_UTMI_CLK>; -+ clock-names = "cfg_noc", -+ "core", -+ "sleep", -+ "mock_utmi"; -+ -+ assigned-clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>, -+ <&gcc GCC_USB0_MASTER_CLK>, -+ <&gcc GCC_USB0_MOCK_UTMI_CLK>; -+ assigned-clock-rates = <133330000>, -+ <133330000>, -+ <24000000>; -+ -+ resets = <&gcc GCC_USB0_BCR>; -+ status = "disabled"; -+ -+ dwc_0: usb@8a00000 { -+ compatible = "snps,dwc3"; -+ reg = <0x0 0x08a00000 0x0 0xcd00>; -+ interrupts = ; -+ phys = <&qusb_phy_0>, <&usb0_ssphy>; -+ phy-names = "usb2-phy", "usb3-phy"; -+ clocks = <&xo>; -+ clock-names = "ref"; -+ tx-fifo-resize; -+ snps,is-utmi-l1-suspend; -+ snps,hird-threshold = /bits/ 8 <0x0>; -+ snps,dis_u2_susphy_quirk; -+ snps,dis_u3_susphy_quirk; -+ dr_mode = "host"; -+ }; -+ }; -+ - intc: interrupt-controller@b000000 { - compatible = "qcom,msm-qgic2"; - #address-cells = <2>; -@@ -386,105 +582,6 @@ - }; - }; - -- pcie_phy: phy@84000 { -- compatible = "qcom,ipq6018-qmp-pcie-phy"; -- reg = <0x0 0x00084000 0x0 0x1bc>; /* Serdes PLL */ -- status = "disabled"; -- #address-cells = <2>; -- #size-cells = <2>; -- ranges; -- -- clocks = <&gcc GCC_PCIE0_AUX_CLK>, -- <&gcc GCC_PCIE0_AHB_CLK>; -- clock-names = "aux", "cfg_ahb"; -- -- resets = <&gcc GCC_PCIE0_PHY_BCR>, -- <&gcc GCC_PCIE0PHY_PHY_BCR>; -- reset-names = "phy", -- "common"; -- -- pcie_phy0: phy@84200 { -- reg = <0x0 0x00084200 0x0 0x16c>, /* Serdes Tx */ -- <0x0 0x00084400 0x0 0x200>, /* Serdes Rx */ -- <0x0 0x00084800 0x0 0x1f0>, /* PCS: Lane0, COM, PCIE */ -- <0x0 0x00084c00 0x0 0xf4>; /* pcs_misc */ -- #phy-cells = <0>; -- -- clocks = <&gcc GCC_PCIE0_PIPE_CLK>; -- clock-names = "pipe0"; -- clock-output-names = "gcc_pcie0_pipe_clk_src"; -- #clock-cells = <0>; -- }; -- }; -- -- pcie0: pci@20000000 { -- compatible = "qcom,pcie-ipq6018"; -- reg = <0x0 0x20000000 0x0 0xf1d>, -- <0x0 0x20000f20 0x0 0xa8>, -- <0x0 0x20001000 0x0 0x1000>, -- <0x0 0x80000 0x0 0x4000>, -- <0x0 0x20100000 0x0 0x1000>; -- reg-names = "dbi", "elbi", "atu", "parf", "config"; -- -- device_type = "pci"; -- linux,pci-domain = <0>; -- bus-range = <0x00 0xff>; -- num-lanes = <1>; -- max-link-speed = <3>; -- #address-cells = <3>; -- #size-cells = <2>; -- -- phys = <&pcie_phy0>; -- phy-names = "pciephy"; -- -- ranges = <0x81000000 0x0 0x00000000 0x0 0x20200000 0x0 0x10000>, -- <0x82000000 0x0 0x20220000 0x0 0x20220000 0x0 0xfde0000>; -- -- interrupts = ; -- interrupt-names = "msi"; -- -- #interrupt-cells = <1>; -- interrupt-map-mask = <0 0 0 0x7>; -- interrupt-map = <0 0 0 1 &intc 0 75 -- IRQ_TYPE_LEVEL_HIGH>, /* int_a */ -- <0 0 0 2 &intc 0 78 -- IRQ_TYPE_LEVEL_HIGH>, /* int_b */ -- <0 0 0 3 &intc 0 79 -- IRQ_TYPE_LEVEL_HIGH>, /* int_c */ -- <0 0 0 4 &intc 0 83 -- IRQ_TYPE_LEVEL_HIGH>; /* int_d */ -- -- clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>, -- <&gcc GCC_PCIE0_AXI_M_CLK>, -- <&gcc GCC_PCIE0_AXI_S_CLK>, -- <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>, -- <&gcc PCIE0_RCHNG_CLK>; -- clock-names = "iface", -- "axi_m", -- "axi_s", -- "axi_bridge", -- "rchng"; -- -- resets = <&gcc GCC_PCIE0_PIPE_ARES>, -- <&gcc GCC_PCIE0_SLEEP_ARES>, -- <&gcc GCC_PCIE0_CORE_STICKY_ARES>, -- <&gcc GCC_PCIE0_AXI_MASTER_ARES>, -- <&gcc GCC_PCIE0_AXI_SLAVE_ARES>, -- <&gcc GCC_PCIE0_AHB_ARES>, -- <&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>, -- <&gcc GCC_PCIE0_AXI_SLAVE_STICKY_ARES>; -- reset-names = "pipe", -- "sleep", -- "sticky", -- "axi_m", -- "axi_s", -- "ahb", -- "axi_m_sticky", -- "axi_s_sticky"; -- -- status = "disabled"; -- }; -- - watchdog@b017000 { - compatible = "qcom,kpss-wdt"; - interrupts = ; -@@ -617,147 +714,74 @@ - }; - }; - -- mdio: mdio@90000 { -- #address-cells = <1>; -- #size-cells = <0>; -- compatible = "qcom,ipq6018-mdio", "qcom,ipq4019-mdio"; -- reg = <0x0 0x00090000 0x0 0x64>; -- clocks = <&gcc GCC_MDIO_AHB_CLK>; -- clock-names = "gcc_mdio_ahb_clk"; -- status = "disabled"; -- }; -- -- qusb_phy_1: qusb@59000 { -- compatible = "qcom,ipq6018-qusb2-phy"; -- reg = <0x0 0x00059000 0x0 0x180>; -- #phy-cells = <0>; -- -- clocks = <&gcc GCC_USB1_PHY_CFG_AHB_CLK>, -- <&xo>; -- clock-names = "cfg_ahb", "ref"; -- -- resets = <&gcc GCC_QUSB2_1_PHY_BCR>; -- status = "disabled"; -- }; -- -- usb2: usb@70f8800 { -- compatible = "qcom,ipq6018-dwc3", "qcom,dwc3"; -- reg = <0x0 0x070F8800 0x0 0x400>; -- #address-cells = <2>; -- #size-cells = <2>; -- ranges; -- clocks = <&gcc GCC_USB1_MASTER_CLK>, -- <&gcc GCC_USB1_SLEEP_CLK>, -- <&gcc GCC_USB1_MOCK_UTMI_CLK>; -- clock-names = "core", -- "sleep", -- "mock_utmi"; -- -- assigned-clocks = <&gcc GCC_USB1_MASTER_CLK>, -- <&gcc GCC_USB1_MOCK_UTMI_CLK>; -- assigned-clock-rates = <133330000>, -- <24000000>; -- resets = <&gcc GCC_USB1_BCR>; -- status = "disabled"; -- -- dwc_1: usb@7000000 { -- compatible = "snps,dwc3"; -- reg = <0x0 0x07000000 0x0 0xcd00>; -- interrupts = ; -- phys = <&qusb_phy_1>; -- phy-names = "usb2-phy"; -- tx-fifo-resize; -- snps,is-utmi-l1-suspend; -- snps,hird-threshold = /bits/ 8 <0x0>; -- snps,dis_u2_susphy_quirk; -- snps,dis_u3_susphy_quirk; -- dr_mode = "host"; -- }; -- }; -+ pcie0: pci@20000000 { -+ compatible = "qcom,pcie-ipq6018"; -+ reg = <0x0 0x20000000 0x0 0xf1d>, -+ <0x0 0x20000f20 0x0 0xa8>, -+ <0x0 0x20001000 0x0 0x1000>, -+ <0x0 0x80000 0x0 0x4000>, -+ <0x0 0x20100000 0x0 0x1000>; -+ reg-names = "dbi", "elbi", "atu", "parf", "config"; - -- ssphy_0: ssphy@78000 { -- compatible = "qcom,ipq6018-qmp-usb3-phy"; -- reg = <0x0 0x00078000 0x0 0x1c4>; -- #address-cells = <2>; -+ device_type = "pci"; -+ linux,pci-domain = <0>; -+ bus-range = <0x00 0xff>; -+ num-lanes = <1>; -+ max-link-speed = <3>; -+ #address-cells = <3>; - #size-cells = <2>; -- ranges; -- -- clocks = <&gcc GCC_USB0_AUX_CLK>, -- <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, <&xo>; -- clock-names = "aux", "cfg_ahb", "ref"; -- -- resets = <&gcc GCC_USB0_PHY_BCR>, -- <&gcc GCC_USB3PHY_0_PHY_BCR>; -- reset-names = "phy","common"; -- status = "disabled"; -- -- usb0_ssphy: phy@78200 { -- reg = <0x0 0x00078200 0x0 0x130>, /* Tx */ -- <0x0 0x00078400 0x0 0x200>, /* Rx */ -- <0x0 0x00078800 0x0 0x1f8>, /* PCS */ -- <0x0 0x00078600 0x0 0x044>; /* PCS misc */ -- #phy-cells = <0>; -- #clock-cells = <0>; -- clocks = <&gcc GCC_USB0_PIPE_CLK>; -- clock-names = "pipe0"; -- clock-output-names = "gcc_usb0_pipe_clk_src"; -- }; -- }; - -- qusb_phy_0: qusb@79000 { -- compatible = "qcom,ipq6018-qusb2-phy"; -- reg = <0x0 0x00079000 0x0 0x180>; -- #phy-cells = <0>; -+ phys = <&pcie_phy0>; -+ phy-names = "pciephy"; - -- clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, -- <&xo>; -- clock-names = "cfg_ahb", "ref"; -+ ranges = <0x81000000 0 0x20200000 0 0x20200000 -+ 0 0x10000>, /* downstream I/O */ -+ <0x82000000 0 0x20220000 0 0x20220000 -+ 0 0xfde0000>; /* non-prefetchable memory */ - -- resets = <&gcc GCC_QUSB2_0_PHY_BCR>; -- status = "disabled"; -- }; -+ interrupts = ; -+ interrupt-names = "msi"; - -- usb3: usb@8af8800 { -- compatible = "qcom,ipq6018-dwc3", "qcom,dwc3"; -- reg = <0x0 0x8af8800 0x0 0x400>; -- #address-cells = <2>; -- #size-cells = <2>; -- ranges; -+ #interrupt-cells = <1>; -+ interrupt-map-mask = <0 0 0 0x7>; -+ interrupt-map = <0 0 0 1 &intc 0 75 -+ IRQ_TYPE_LEVEL_HIGH>, /* int_a */ -+ <0 0 0 2 &intc 0 78 -+ IRQ_TYPE_LEVEL_HIGH>, /* int_b */ -+ <0 0 0 3 &intc 0 79 -+ IRQ_TYPE_LEVEL_HIGH>, /* int_c */ -+ <0 0 0 4 &intc 0 83 -+ IRQ_TYPE_LEVEL_HIGH>; /* int_d */ - -- clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>, -- <&gcc GCC_USB0_MASTER_CLK>, -- <&gcc GCC_USB0_SLEEP_CLK>, -- <&gcc GCC_USB0_MOCK_UTMI_CLK>; -- clock-names = "cfg_noc", -- "core", -- "sleep", -- "mock_utmi"; -+ clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>, -+ <&gcc GCC_PCIE0_AXI_M_CLK>, -+ <&gcc GCC_PCIE0_AXI_S_CLK>, -+ <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>, -+ <&gcc PCIE0_RCHNG_CLK>; -+ clock-names = "iface", -+ "axi_m", -+ "axi_s", -+ "axi_bridge", -+ "rchng"; - -- assigned-clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>, -- <&gcc GCC_USB0_MASTER_CLK>, -- <&gcc GCC_USB0_MOCK_UTMI_CLK>; -- assigned-clock-rates = <133330000>, -- <133330000>, -- <24000000>; -+ resets = <&gcc GCC_PCIE0_PIPE_ARES>, -+ <&gcc GCC_PCIE0_SLEEP_ARES>, -+ <&gcc GCC_PCIE0_CORE_STICKY_ARES>, -+ <&gcc GCC_PCIE0_AXI_MASTER_ARES>, -+ <&gcc GCC_PCIE0_AXI_SLAVE_ARES>, -+ <&gcc GCC_PCIE0_AHB_ARES>, -+ <&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>, -+ <&gcc GCC_PCIE0_AXI_SLAVE_STICKY_ARES>; -+ reset-names = "pipe", -+ "sleep", -+ "sticky", -+ "axi_m", -+ "axi_s", -+ "ahb", -+ "axi_m_sticky", -+ "axi_s_sticky"; - -- resets = <&gcc GCC_USB0_BCR>; - status = "disabled"; -- -- dwc_0: usb@8a00000 { -- compatible = "snps,dwc3"; -- reg = <0x0 0x8a00000 0x0 0xcd00>; -- interrupts = ; -- phys = <&qusb_phy_0>, <&usb0_ssphy>; -- phy-names = "usb2-phy", "usb3-phy"; -- clocks = <&xo>; -- clock-names = "ref"; -- tx-fifo-resize; -- snps,is-utmi-l1-suspend; -- snps,hird-threshold = /bits/ 8 <0x0>; -- snps,dis_u2_susphy_quirk; -- snps,dis_u3_susphy_quirk; -- dr_mode = "host"; -- }; - }; - }; - -@@ -792,26 +816,4 @@ - #interrupt-cells = <2>; - }; - }; -- -- rpm-glink { -- compatible = "qcom,glink-rpm"; -- interrupts = ; -- qcom,rpm-msg-ram = <&rpm_msg_ram>; -- mboxes = <&apcs_glb 0>; -- -- rpm_requests: glink-channel { -- compatible = "qcom,rpm-ipq6018"; -- qcom,glink-channels = "rpm_requests"; -- -- regulators { -- compatible = "qcom,rpm-mp5496-regulators"; -- -- ipq6018_s2: s2 { -- regulator-min-microvolt = <725000>; -- regulator-max-microvolt = <1062500>; -- regulator-always-on; -- }; -- }; -- }; -- }; - }; diff --git a/target/linux/qualcommax/patches-6.1/0035-v6.3-arm64-dts-qcom-ipq6018-Add-remove-some-newlines.patch b/target/linux/qualcommax/patches-6.1/0035-v6.3-arm64-dts-qcom-ipq6018-Add-remove-some-newlines.patch deleted file mode 100644 index a883e305df..0000000000 --- a/target/linux/qualcommax/patches-6.1/0035-v6.3-arm64-dts-qcom-ipq6018-Add-remove-some-newlines.patch +++ /dev/null @@ -1,92 +0,0 @@ -From 6db9ed9a128cbae1423d043f3debd8bfa77783fd Mon Sep 17 00:00:00 2001 -From: Konrad Dybcio -Date: Mon, 2 Jan 2023 10:46:29 +0100 -Subject: [PATCH] arm64: dts: qcom: ipq6018: Add/remove some newlines - -Some lines were broken very aggresively, presumably to fit under 80 chars -and some places could have used a newline, particularly between subsequent -nodes. Address all that and remove redundant comments near PCIe ranges -while at it so as not to exceed 100 chars needlessly. - -Signed-off-by: Konrad Dybcio -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20230102094642.74254-5-konrad.dybcio@linaro.org ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 26 ++++++++++++-------------- - 1 file changed, 12 insertions(+), 14 deletions(-) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -102,26 +102,31 @@ - opp-microvolt = <725000>; - clock-latency-ns = <200000>; - }; -+ - opp-1056000000 { - opp-hz = /bits/ 64 <1056000000>; - opp-microvolt = <787500>; - clock-latency-ns = <200000>; - }; -+ - opp-1320000000 { - opp-hz = /bits/ 64 <1320000000>; - opp-microvolt = <862500>; - clock-latency-ns = <200000>; - }; -+ - opp-1440000000 { - opp-hz = /bits/ 64 <1440000000>; - opp-microvolt = <925000>; - clock-latency-ns = <200000>; - }; -+ - opp-1608000000 { - opp-hz = /bits/ 64 <1608000000>; - opp-microvolt = <987500>; - clock-latency-ns = <200000>; - }; -+ - opp-1800000000 { - opp-hz = /bits/ 64 <1800000000>; - opp-microvolt = <1062500>; -@@ -131,8 +136,7 @@ - - pmuv8: pmu { - compatible = "arm,cortex-a53-pmu"; -- interrupts = ; -+ interrupts = ; - }; - - psci: psci { -@@ -734,24 +738,18 @@ - phys = <&pcie_phy0>; - phy-names = "pciephy"; - -- ranges = <0x81000000 0 0x20200000 0 0x20200000 -- 0 0x10000>, /* downstream I/O */ -- <0x82000000 0 0x20220000 0 0x20220000 -- 0 0xfde0000>; /* non-prefetchable memory */ -+ ranges = <0x81000000 0 0x20200000 0 0x20200000 0 0x10000>, -+ <0x82000000 0 0x20220000 0 0x20220000 0 0xfde0000>; - - interrupts = ; - interrupt-names = "msi"; - - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0x7>; -- interrupt-map = <0 0 0 1 &intc 0 75 -- IRQ_TYPE_LEVEL_HIGH>, /* int_a */ -- <0 0 0 2 &intc 0 78 -- IRQ_TYPE_LEVEL_HIGH>, /* int_b */ -- <0 0 0 3 &intc 0 79 -- IRQ_TYPE_LEVEL_HIGH>, /* int_c */ -- <0 0 0 4 &intc 0 83 -- IRQ_TYPE_LEVEL_HIGH>; /* int_d */ -+ interrupt-map = <0 0 0 1 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ -+ <0 0 0 2 &intc 0 78 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ -+ <0 0 0 3 &intc 0 79 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ -+ <0 0 0 4 &intc 0 83 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ - - clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>, - <&gcc GCC_PCIE0_AXI_M_CLK>, diff --git a/target/linux/qualcommax/patches-6.1/0036-v6.3-arm64-dts-qcom-ipq6018-Use-lowercase-hex.patch b/target/linux/qualcommax/patches-6.1/0036-v6.3-arm64-dts-qcom-ipq6018-Use-lowercase-hex.patch deleted file mode 100644 index 35aa46bb10..0000000000 --- a/target/linux/qualcommax/patches-6.1/0036-v6.3-arm64-dts-qcom-ipq6018-Use-lowercase-hex.patch +++ /dev/null @@ -1,25 +0,0 @@ -From 7356ae3e10abd1d71f06ff0b8a8e72aa7c955c57 Mon Sep 17 00:00:00 2001 -From: Konrad Dybcio -Date: Mon, 2 Jan 2023 10:46:30 +0100 -Subject: [PATCH] arm64: dts: qcom: ipq6018: Use lowercase hex - -One value escaped my previous lowercase hexification. Take care of it. - -Signed-off-by: Konrad Dybcio -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20230102094642.74254-6-konrad.dybcio@linaro.org ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 2 +- - 1 file changed, 1 insertion(+), 1 deletion(-) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -381,7 +381,7 @@ - - usb2: usb@70f8800 { - compatible = "qcom,ipq6018-dwc3", "qcom,dwc3"; -- reg = <0x0 0x070F8800 0x0 0x400>; -+ reg = <0x0 0x070f8800 0x0 0x400>; - #address-cells = <2>; - #size-cells = <2>; - ranges; diff --git a/target/linux/qualcommax/patches-6.1/0037-v6.3-arm64-dts-qcom-ipq6018-align-RPM-G-Link-node-with.patch b/target/linux/qualcommax/patches-6.1/0037-v6.3-arm64-dts-qcom-ipq6018-align-RPM-G-Link-node-with.patch deleted file mode 100644 index c939d126bf..0000000000 --- a/target/linux/qualcommax/patches-6.1/0037-v6.3-arm64-dts-qcom-ipq6018-align-RPM-G-Link-node-with.patch +++ /dev/null @@ -1,28 +0,0 @@ -From 679ee73bbee28cab441008f8cca38160cc8f3d05 Mon Sep 17 00:00:00 2001 -From: Krzysztof Kozlowski -Date: Wed, 8 Feb 2023 11:15:39 +0100 -Subject: [PATCH] arm64: dts: qcom: ipq6018: align RPM G-Link node with - bindings - -Bindings expect (and most of DTS use) the RPM G-Link node name to be -"rpm-requests". - -Signed-off-by: Krzysztof Kozlowski -Reviewed-by: Dmitry Baryshkov -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20230208101545.45711-1-krzysztof.kozlowski@linaro.org ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 2 +- - 1 file changed, 1 insertion(+), 1 deletion(-) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -176,7 +176,7 @@ - qcom,rpm-msg-ram = <&rpm_msg_ram>; - mboxes = <&apcs_glb 0>; - -- rpm_requests: glink-channel { -+ rpm_requests: rpm-requests { - compatible = "qcom,rpm-ipq6018"; - qcom,glink-channels = "rpm_requests"; - diff --git a/target/linux/qualcommax/patches-6.1/0038-v6.4-arm64-dts-qcom-ipq6018-cp01-c1-drop-SPI-cs-select.patch b/target/linux/qualcommax/patches-6.1/0038-v6.4-arm64-dts-qcom-ipq6018-cp01-c1-drop-SPI-cs-select.patch deleted file mode 100644 index 28688069b8..0000000000 --- a/target/linux/qualcommax/patches-6.1/0038-v6.4-arm64-dts-qcom-ipq6018-cp01-c1-drop-SPI-cs-select.patch +++ /dev/null @@ -1,27 +0,0 @@ -From afa8eb675fc6dd606783ed2350de90927d6fb9d3 Mon Sep 17 00:00:00 2001 -From: Krzysztof Kozlowski -Date: Wed, 8 Mar 2023 13:59:01 +0100 -Subject: [PATCH] arm64: dts: qcom: ipq6018-cp01-c1: drop SPI cs-select - -The SPI controller nodes do not use/allow cs-select property: - - ipq6018-cp01-c1.dtb: spi@78b5000: Unevaluated properties are not allowed ('cs-select' was unexpected) - -Signed-off-by: Krzysztof Kozlowski -Reviewed-by: Konrad Dybcio -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20230308125906.236885-6-krzysztof.kozlowski@linaro.org ---- - arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts | 1 - - 1 file changed, 1 deletion(-) - ---- a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts -+++ b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts -@@ -36,7 +36,6 @@ - }; - - &blsp1_spi1 { -- cs-select = <0>; - pinctrl-0 = <&spi_0_pins>; - pinctrl-names = "default"; - status = "okay"; diff --git a/target/linux/qualcommax/patches-6.1/0039-v6.5-arm64-dts-qcom-add-few-more-reserved-memory-region.patch b/target/linux/qualcommax/patches-6.1/0039-v6.5-arm64-dts-qcom-add-few-more-reserved-memory-region.patch deleted file mode 100644 index d1280b528b..0000000000 --- a/target/linux/qualcommax/patches-6.1/0039-v6.5-arm64-dts-qcom-add-few-more-reserved-memory-region.patch +++ /dev/null @@ -1,92 +0,0 @@ -From 0cd4e90cb2dec02ff859f5c98f744f43a23aea65 Mon Sep 17 00:00:00 2001 -From: Vignesh Viswanathan -Date: Fri, 26 May 2023 16:36:53 +0530 -Subject: [PATCH] arm64: dts: qcom: add few more reserved memory region - -In IPQ SoCs, bootloader will collect the system RAM contents upon crash -for the post morterm analysis. If we don't reserve the memory region used -by bootloader, obviously linux will consume it and upon next boot on -crash, bootloader will be loaded in the same region, which will lead to -loose some of the data, sometimes we may miss out critical information. -So lets reserve the region used by the bootloader. - -Similarly SBL copies some data into the reserved region and it will be -used in the crash scenario. So reserve 1MB for SBL as well. - -While at it, drop the size padding in the reserved memory region, -wherever applicable. - -Signed-off-by: Vignesh Viswanathan -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20230526110653.27777-4-quic_viswanat@quicinc.com ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 16 +++++++++++++--- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 14 ++++++++++++-- - 2 files changed, 25 insertions(+), 5 deletions(-) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -154,18 +154,28 @@ - no-map; - }; - -+ bootloader@4a100000 { -+ reg = <0x0 0x4a100000 0x0 0x400000>; -+ no-map; -+ }; -+ -+ sbl@4a500000 { -+ reg = <0x0 0x4a500000 0x0 0x100000>; -+ no-map; -+ }; -+ - tz: memory@4a600000 { -- reg = <0x0 0x4a600000 0x0 0x00400000>; -+ reg = <0x0 0x4a600000 0x0 0x400000>; - no-map; - }; - - smem_region: memory@4aa00000 { -- reg = <0x0 0x4aa00000 0x0 0x00100000>; -+ reg = <0x0 0x4aa00000 0x0 0x100000>; - no-map; - }; - - q6_region: memory@4ab00000 { -- reg = <0x0 0x4ab00000 0x0 0x05500000>; -+ reg = <0x0 0x4ab00000 0x0 0x5500000>; - no-map; - }; - }; ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -85,17 +85,27 @@ - #size-cells = <2>; - ranges; - -+ bootloader@4a600000 { -+ reg = <0x0 0x4a600000 0x0 0x400000>; -+ no-map; -+ }; -+ -+ sbl@4aa00000 { -+ reg = <0x0 0x4aa00000 0x0 0x100000>; -+ no-map; -+ }; -+ - smem@4ab00000 { - compatible = "qcom,smem"; -- reg = <0x0 0x4ab00000 0x0 0x00100000>; -+ reg = <0x0 0x4ab00000 0x0 0x100000>; - no-map; - - hwlocks = <&tcsr_mutex 3>; - }; - - memory@4ac00000 { -+ reg = <0x0 0x4ac00000 0x0 0x400000>; - no-map; -- reg = <0x0 0x4ac00000 0x0 0x00400000>; - }; - }; - diff --git a/target/linux/qualcommax/patches-6.1/0040-v6.5-arm64-dts-qcom-enable-the-download-mode-support.patch b/target/linux/qualcommax/patches-6.1/0040-v6.5-arm64-dts-qcom-enable-the-download-mode-support.patch deleted file mode 100644 index 6dd185f6e0..0000000000 --- a/target/linux/qualcommax/patches-6.1/0040-v6.5-arm64-dts-qcom-enable-the-download-mode-support.patch +++ /dev/null @@ -1,49 +0,0 @@ -From 9b2406aaba7841863ac041225316c1ec1c86ea36 Mon Sep 17 00:00:00 2001 -From: Vignesh Viswanathan -Date: Fri, 26 May 2023 16:36:52 +0530 -Subject: [PATCH] arm64: dts: qcom: enable the download mode support - -Like any other Qualcomm SoCs, IPQ8074 and IPQ6018 also supports the -download mode to collect the RAM dumps if system crashes, to perform -the post mortem analysis. Add support for the same. - -Signed-off-by: Vignesh Viswanathan -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20230526110653.27777-3-quic_viswanat@quicinc.com ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 1 + - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 6 ++++++ - 2 files changed, 7 insertions(+) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -90,6 +90,7 @@ - firmware { - scm { - compatible = "qcom,scm-ipq6018", "qcom,scm"; -+ qcom,dload-mode = <&tcsr 0x6100>; - }; - }; - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -112,6 +112,7 @@ - firmware { - scm { - compatible = "qcom,scm-ipq8074", "qcom,scm"; -+ qcom,dload-mode = <&tcsr 0x6100>; - }; - }; - -@@ -386,6 +387,11 @@ - #hwlock-cells = <1>; - }; - -+ tcsr: syscon@1937000 { -+ compatible = "qcom,tcsr-ipq8074", "syscon"; -+ reg = <0x01937000 0x21000>; -+ }; -+ - spmi_bus: spmi@200f000 { - compatible = "qcom,spmi-pmic-arb"; - reg = <0x0200f000 0x001000>, diff --git a/target/linux/qualcommax/patches-6.1/0041-v6.5-arm64-dts-qcom-ipq6018-correct-qrng-unit-address.patch b/target/linux/qualcommax/patches-6.1/0041-v6.5-arm64-dts-qcom-ipq6018-correct-qrng-unit-address.patch deleted file mode 100644 index e9b92b596e..0000000000 --- a/target/linux/qualcommax/patches-6.1/0041-v6.5-arm64-dts-qcom-ipq6018-correct-qrng-unit-address.patch +++ /dev/null @@ -1,29 +0,0 @@ -From 085058786a7890dd44ec623fe5ac74db870f6b93 Mon Sep 17 00:00:00 2001 -From: Krzysztof Kozlowski -Date: Wed, 19 Apr 2023 23:18:39 +0200 -Subject: [PATCH] arm64: dts: qcom: ipq6018: correct qrng unit address - -Match unit-address to reg entry to fix dtbs W=1 warnings: - - Warning (simple_bus_reg): /soc/qrng@e1000: simple-bus unit address format error, expected "e3000" - -Fixes: 5bf635621245 ("arm64: dts: ipq6018: Add a few device nodes") -Signed-off-by: Krzysztof Kozlowski -Reviewed-by: Konrad Dybcio -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20230419211856.79332-1-krzysztof.kozlowski@linaro.org ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 2 +- - 1 file changed, 1 insertion(+), 1 deletion(-) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -312,7 +312,7 @@ - status = "disabled"; - }; - -- prng: qrng@e1000 { -+ prng: qrng@e3000 { - compatible = "qcom,prng-ee"; - reg = <0x0 0x000e3000 0x0 0x1000>; - clocks = <&gcc GCC_PRNG_AHB_CLK>; diff --git a/target/linux/qualcommax/patches-6.1/0042-v6.5-arm64-dts-qcom-ipq6018-add-unit-address-to-soc-node.patch b/target/linux/qualcommax/patches-6.1/0042-v6.5-arm64-dts-qcom-ipq6018-add-unit-address-to-soc-node.patch deleted file mode 100644 index 821c9890c6..0000000000 --- a/target/linux/qualcommax/patches-6.1/0042-v6.5-arm64-dts-qcom-ipq6018-add-unit-address-to-soc-node.patch +++ /dev/null @@ -1,28 +0,0 @@ -From 393595d4ffbd0a1fafd5548f8de1b8487a037cf2 Mon Sep 17 00:00:00 2001 -From: Krzysztof Kozlowski -Date: Thu, 20 Apr 2023 08:36:04 +0200 -Subject: [PATCH] arm64: dts: qcom: ipq6018: add unit address to soc node - -"soc" node is supposed to have unit address: - - Warning (unit_address_vs_reg): /soc: node has a reg or ranges property, but no unit name - -Signed-off-by: Krzysztof Kozlowski -Reviewed-by: Konrad Dybcio -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20230420063610.11068-1-krzysztof.kozlowski@linaro.org ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 2 +- - 1 file changed, 1 insertion(+), 1 deletion(-) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -209,7 +209,7 @@ - hwlocks = <&tcsr_mutex 3>; - }; - -- soc: soc { -+ soc: soc@0 { - #address-cells = <2>; - #size-cells = <2>; - ranges = <0 0 0 0 0x0 0xffffffff>; diff --git a/target/linux/qualcommax/patches-6.1/0043-v6.5-arm64-dts-qcom-ipq6018-add-QFPROM-node.patch b/target/linux/qualcommax/patches-6.1/0043-v6.5-arm64-dts-qcom-ipq6018-add-QFPROM-node.patch deleted file mode 100644 index 68895c5c96..0000000000 --- a/target/linux/qualcommax/patches-6.1/0043-v6.5-arm64-dts-qcom-ipq6018-add-QFPROM-node.patch +++ /dev/null @@ -1,34 +0,0 @@ -From 546f0617a22a481f3ca1f7e058aea0c40517c64e Mon Sep 17 00:00:00 2001 -From: Kathiravan T -Date: Fri, 26 May 2023 18:23:04 +0530 -Subject: [PATCH] arm64: dts: qcom: ipq6018: add QFPROM node - -IPQ6018 has efuse region to determine the various HW quirks. Lets -add the initial support and the individual fuses will be added as they -are required. - -Signed-off-by: Kathiravan T -Reviewed-by: Dmitry Baryshkov -Reviewed-by: Konrad Dybcio -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20230526125305.19626-4-quic_kathirav@quicinc.com ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 7 +++++++ - 1 file changed, 7 insertions(+) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -312,6 +312,13 @@ - status = "disabled"; - }; - -+ qfprom: efuse@a4000 { -+ compatible = "qcom,ipq6018-qfprom", "qcom,qfprom"; -+ reg = <0x0 0x000a4000 0x0 0x2000>; -+ #address-cells = <1>; -+ #size-cells = <1>; -+ }; -+ - prng: qrng@e3000 { - compatible = "qcom,prng-ee"; - reg = <0x0 0x000e3000 0x0 0x1000>; diff --git a/target/linux/qualcommax/patches-6.1/0044-v6.5-arm64-dts-qcom-ipq6018-drop-incorrect-SPI-bus.patch b/target/linux/qualcommax/patches-6.1/0044-v6.5-arm64-dts-qcom-ipq6018-drop-incorrect-SPI-bus.patch deleted file mode 100644 index b2057e588e..0000000000 --- a/target/linux/qualcommax/patches-6.1/0044-v6.5-arm64-dts-qcom-ipq6018-drop-incorrect-SPI-bus.patch +++ /dev/null @@ -1,37 +0,0 @@ -From b8420d478aa3fc739fcdba6b4b945850b356cb3b Mon Sep 17 00:00:00 2001 -From: Krzysztof Kozlowski -Date: Sun, 16 Apr 2023 14:37:25 +0200 -Subject: [PATCH] arm64: dts: qcom: ipq6018: drop incorrect SPI bus - spi-max-frequency - -The spi-max-frequency property belongs to SPI devices, not SPI -controller: - - ipq6018-cp01-c1.dtb: spi@78b5000: Unevaluated properties are not allowed ('spi-max-frequency' was unexpected) - -Signed-off-by: Krzysztof Kozlowski -Reviewed-by: Konrad Dybcio -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20230416123730.300863-1-krzysztof.kozlowski@linaro.org ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 2 -- - 1 file changed, 2 deletions(-) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -458,7 +458,6 @@ - #size-cells = <0>; - reg = <0x0 0x078b5000 0x0 0x600>; - interrupts = ; -- spi-max-frequency = <50000000>; - clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>, - <&gcc GCC_BLSP1_AHB_CLK>; - clock-names = "core", "iface"; -@@ -473,7 +472,6 @@ - #size-cells = <0>; - reg = <0x0 0x078b6000 0x0 0x600>; - interrupts = ; -- spi-max-frequency = <50000000>; - clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>, - <&gcc GCC_BLSP1_AHB_CLK>; - clock-names = "core", "iface"; diff --git a/target/linux/qualcommax/patches-6.1/0045-v6.5-arm64-dts-qcom-ipq8074-drop-incorrect-SPI-bus.patch b/target/linux/qualcommax/patches-6.1/0045-v6.5-arm64-dts-qcom-ipq8074-drop-incorrect-SPI-bus.patch deleted file mode 100644 index 52ba16cc9f..0000000000 --- a/target/linux/qualcommax/patches-6.1/0045-v6.5-arm64-dts-qcom-ipq8074-drop-incorrect-SPI-bus.patch +++ /dev/null @@ -1,29 +0,0 @@ -From e6e0e706940b64e3a77e0a4840037692f109bd5f Mon Sep 17 00:00:00 2001 -From: Krzysztof Kozlowski -Date: Sun, 16 Apr 2023 14:37:26 +0200 -Subject: [PATCH] arm64: dts: qcom: ipq8074: drop incorrect SPI bus - spi-max-frequency - -The spi-max-frequency property belongs to SPI devices, not SPI -controller: - - ipq8074-hk01.dtb: spi@78b5000: Unevaluated properties are not allowed ('spi-max-frequency' was unexpected) - -Signed-off-by: Krzysztof Kozlowski -Reviewed-by: Konrad Dybcio -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20230416123730.300863-2-krzysztof.kozlowski@linaro.org ---- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 1 - - 1 file changed, 1 deletion(-) - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -487,7 +487,6 @@ - #size-cells = <0>; - reg = <0x078b5000 0x600>; - interrupts = ; -- spi-max-frequency = <50000000>; - clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>, - <&gcc GCC_BLSP1_AHB_CLK>; - clock-names = "core", "iface"; diff --git a/target/linux/qualcommax/patches-6.1/0046-v6.6-clk-qcom-gcc-ipq6018-Use-floor-ops-for-sdcc-clocks.patch b/target/linux/qualcommax/patches-6.1/0046-v6.6-clk-qcom-gcc-ipq6018-Use-floor-ops-for-sdcc-clocks.patch deleted file mode 100644 index 9ae72730d8..0000000000 --- a/target/linux/qualcommax/patches-6.1/0046-v6.6-clk-qcom-gcc-ipq6018-Use-floor-ops-for-sdcc-clocks.patch +++ /dev/null @@ -1,27 +0,0 @@ -From 56e5ae0116aef87273cf1812d608645b076e4f02 Mon Sep 17 00:00:00 2001 -From: Mantas Pucka -Date: Tue, 25 Apr 2023 12:11:49 +0300 -Subject: [PATCH] clk: qcom: gcc-ipq6018: Use floor ops for sdcc clocks - -SDCC clocks must be rounded down to avoid overclocking the controller. - -Fixes: d9db07f088af ("clk: qcom: Add ipq6018 Global Clock Controller support") -Signed-off-by: Mantas Pucka -Reviewed-by: Konrad Dybcio -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/1682413909-24927-1-git-send-email-mantas@8devices.com ---- - drivers/clk/qcom/gcc-ipq6018.c | 2 +- - 1 file changed, 1 insertion(+), 1 deletion(-) - ---- a/drivers/clk/qcom/gcc-ipq6018.c -+++ b/drivers/clk/qcom/gcc-ipq6018.c -@@ -1702,7 +1702,7 @@ static struct clk_rcg2 usb0_mock_utmi_cl - .name = "usb0_mock_utmi_clk_src", - .parent_data = gcc_xo_gpll6_gpll0_gpll0_out_main_div2, - .num_parents = 4, -- .ops = &clk_rcg2_ops, -+ .ops = &clk_rcg2_floor_ops, - }, - }; - diff --git a/target/linux/qualcommax/patches-6.1/0047-v6.6-clk-qcom-gcc-ipq6018-drop-redundant-F-define.patch b/target/linux/qualcommax/patches-6.1/0047-v6.6-clk-qcom-gcc-ipq6018-drop-redundant-F-define.patch deleted file mode 100644 index 19dc9482e6..0000000000 --- a/target/linux/qualcommax/patches-6.1/0047-v6.6-clk-qcom-gcc-ipq6018-drop-redundant-F-define.patch +++ /dev/null @@ -1,27 +0,0 @@ -From 923f7d678b2ae3d522543058514d5605c185633b Mon Sep 17 00:00:00 2001 -From: Christian Marangi -Date: Mon, 17 Apr 2023 19:44:07 +0200 -Subject: [PATCH] clk: qcom: gcc-ipq6018: drop redundant F define - -The same exact F frequency table entry is defined in clk-rcg.h -Drop the redundant define to cleanup code. - -Signed-off-by: Christian Marangi -Reviewed-by: Konrad Dybcio -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20230417174408.23722-1-ansuelsmth@gmail.com ---- - drivers/clk/qcom/gcc-ipq6018.c | 2 -- - 1 file changed, 2 deletions(-) - ---- a/drivers/clk/qcom/gcc-ipq6018.c -+++ b/drivers/clk/qcom/gcc-ipq6018.c -@@ -26,8 +26,6 @@ - #include "clk-regmap-mux.h" - #include "reset.h" - --#define F(f, s, h, m, n) { (f), (s), (2 * (h) - 1), (m), (n) } -- - enum { - P_XO, - P_BIAS_PLL, diff --git a/target/linux/qualcommax/patches-6.1/0048-v6.6-clk-qcom-gcc-ipq6018-update-UBI32-PLL.patch b/target/linux/qualcommax/patches-6.1/0048-v6.6-clk-qcom-gcc-ipq6018-update-UBI32-PLL.patch deleted file mode 100644 index e38b40278c..0000000000 --- a/target/linux/qualcommax/patches-6.1/0048-v6.6-clk-qcom-gcc-ipq6018-update-UBI32-PLL.patch +++ /dev/null @@ -1,39 +0,0 @@ -From f4f0c8acee0e41c5fbae7a7ad06087668ddce0d6 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Fri, 26 May 2023 21:08:54 +0200 -Subject: [PATCH] clk: qcom: gcc-ipq6018: update UBI32 PLL - -Update the UBI32 alpha PLL config to the latest values from the downstream -QCA 5.4 kernel. - -Signed-off-by: Robert Marko -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20230526190855.2941291-1-robimarko@gmail.com ---- - drivers/clk/qcom/gcc-ipq6018.c | 7 ++++++- - 1 file changed, 6 insertions(+), 1 deletion(-) - ---- a/drivers/clk/qcom/gcc-ipq6018.c -+++ b/drivers/clk/qcom/gcc-ipq6018.c -@@ -4143,15 +4143,20 @@ static struct clk_branch gcc_dcc_clk = { - - static const struct alpha_pll_config ubi32_pll_config = { - .l = 0x3e, -- .alpha = 0x57, -+ .alpha = 0x6667, - .config_ctl_val = 0x240d6aa8, - .config_ctl_hi_val = 0x3c2, -+ .config_ctl_val = 0x240d4828, -+ .config_ctl_hi_val = 0x6, - .main_output_mask = BIT(0), - .aux_output_mask = BIT(1), - .pre_div_val = 0x0, - .pre_div_mask = BIT(12), - .post_div_val = 0x0, - .post_div_mask = GENMASK(9, 8), -+ .alpha_en_mask = BIT(24), -+ .test_ctl_val = 0x1C0000C0, -+ .test_ctl_hi_val = 0x4000, - }; - - static const struct alpha_pll_config nss_crypto_pll_config = { diff --git a/target/linux/qualcommax/patches-6.1/0049-v6.6-clk-qcom-gcc-ipq6018-remove-duplicate-initializers.patch b/target/linux/qualcommax/patches-6.1/0049-v6.6-clk-qcom-gcc-ipq6018-remove-duplicate-initializers.patch deleted file mode 100644 index e4faac1b6e..0000000000 --- a/target/linux/qualcommax/patches-6.1/0049-v6.6-clk-qcom-gcc-ipq6018-remove-duplicate-initializers.patch +++ /dev/null @@ -1,38 +0,0 @@ -From 5ae7899765607e97e5eb34486336898c8d9ec654 Mon Sep 17 00:00:00 2001 -From: Arnd Bergmann -Date: Thu, 1 Jun 2023 23:34:12 +0200 -Subject: [PATCH] clk: qcom: gcc-ipq6018: remove duplicate initializers - -A recent change added new initializers for .config_ctl_val and -.config_ctl_hi_val but left the old values in place: - -drivers/clk/qcom/gcc-ipq6018.c:4155:27: error: initialized field overwritten [-Werror=override-init] - 4155 | .config_ctl_val = 0x240d4828, - | ^~~~~~~~~~ -drivers/clk/qcom/gcc-ipq6018.c:4156:30: error: initialized field overwritten [-Werror=override-init] - 4156 | .config_ctl_hi_val = 0x6, - | ^~~ - -Remove the unused ones now to avoid confusion. - -Fixes: f4f0c8acee0e4 ("clk: qcom: gcc-ipq6018: update UBI32 PLL") -Signed-off-by: Arnd Bergmann -Reviewed-by: Robert Marko -Reviewed-by: Dmitry Baryshkov -Signed-off-by: Bjorn Andersson -Link: https://lore.kernel.org/r/20230601213416.3373599-1-arnd@kernel.org ---- - drivers/clk/qcom/gcc-ipq6018.c | 2 -- - 1 file changed, 2 deletions(-) - ---- a/drivers/clk/qcom/gcc-ipq6018.c -+++ b/drivers/clk/qcom/gcc-ipq6018.c -@@ -4144,8 +4144,6 @@ static struct clk_branch gcc_dcc_clk = { - static const struct alpha_pll_config ubi32_pll_config = { - .l = 0x3e, - .alpha = 0x6667, -- .config_ctl_val = 0x240d6aa8, -- .config_ctl_hi_val = 0x3c2, - .config_ctl_val = 0x240d4828, - .config_ctl_hi_val = 0x6, - .main_output_mask = BIT(0), diff --git a/target/linux/qualcommax/patches-6.1/0050-v6.6-soc-qcom-Add-RPM-processor-subsystem-driver.patch b/target/linux/qualcommax/patches-6.1/0050-v6.6-soc-qcom-Add-RPM-processor-subsystem-driver.patch deleted file mode 100644 index c2c26fb079..0000000000 --- a/target/linux/qualcommax/patches-6.1/0050-v6.6-soc-qcom-Add-RPM-processor-subsystem-driver.patch +++ /dev/null @@ -1,132 +0,0 @@ -From 8ddfa81d090c71fd6cb3cb8ca1d420c0da33a575 Mon Sep 17 00:00:00 2001 -From: Stephan Gerhold -Date: Thu, 15 Jun 2023 18:50:42 +0200 -Subject: [PATCH] soc: qcom: Add RPM processor/subsystem driver - -Add a simple driver for the qcom,rpm-proc compatible that registers the -"smd-edge" and populates other children defined in the device tree. - -Note that the DT schema belongs to the remoteproc subsystem while this -driver is added inside soc/qcom. I argue that the RPM *is* a remoteproc, -but as an implementation detail in Linux it can currently not benefit -from anything provided by the remoteproc subsystem. The RPM firmware is -usually already loaded and started by earlier components in the boot -chain and is not meant to be ever restarted. - -To avoid breaking existing kernel configurations the driver is always -built when smd-rpm.c is also built. They belong closely together anyway. -To avoid build errors CONFIG_RPMSG_QCOM_SMD must be also built-in if -rpm-proc is. - -Reviewed-by: Konrad Dybcio -Signed-off-by: Stephan Gerhold -Link: https://lore.kernel.org/r/20230531-rpm-rproc-v3-9-a07dcdefd918@gerhold.net -Signed-off-by: Bjorn Andersson ---- - drivers/soc/qcom/Kconfig | 1 + - drivers/soc/qcom/Makefile | 2 +- - drivers/soc/qcom/rpm-proc.c | 77 +++++++++++++++++++++++++++++++++++++ - 3 files changed, 79 insertions(+), 1 deletion(-) - create mode 100644 drivers/soc/qcom/rpm-proc.c - ---- a/drivers/soc/qcom/Kconfig -+++ b/drivers/soc/qcom/Kconfig -@@ -153,6 +153,7 @@ config QCOM_SMD_RPM - tristate "Qualcomm Resource Power Manager (RPM) over SMD" - depends on ARCH_QCOM || COMPILE_TEST - depends on RPMSG -+ depends on RPMSG_QCOM_SMD || RPMSG_QCOM_SMD=n - help - If you say yes to this option, support will be included for the - Resource Power Manager system found in the Qualcomm 8974 based ---- a/drivers/soc/qcom/Makefile -+++ b/drivers/soc/qcom/Makefile -@@ -14,7 +14,7 @@ obj-$(CONFIG_QCOM_RMTFS_MEM) += rmtfs_me - obj-$(CONFIG_QCOM_RPMH) += qcom_rpmh.o - qcom_rpmh-y += rpmh-rsc.o - qcom_rpmh-y += rpmh.o --obj-$(CONFIG_QCOM_SMD_RPM) += smd-rpm.o -+obj-$(CONFIG_QCOM_SMD_RPM) += rpm-proc.o smd-rpm.o - obj-$(CONFIG_QCOM_SMEM) += smem.o - obj-$(CONFIG_QCOM_SMEM_STATE) += smem_state.o - obj-$(CONFIG_QCOM_SMP2P) += smp2p.o ---- /dev/null -+++ b/drivers/soc/qcom/rpm-proc.c -@@ -0,0 +1,77 @@ -+// SPDX-License-Identifier: GPL-2.0-only -+/* Copyright (c) 2021-2023, Stephan Gerhold */ -+ -+#include -+#include -+#include -+#include -+#include -+ -+static int rpm_proc_probe(struct platform_device *pdev) -+{ -+ struct qcom_smd_edge *edge = NULL; -+ struct device *dev = &pdev->dev; -+ struct device_node *edge_node; -+ int ret; -+ -+ edge_node = of_get_child_by_name(dev->of_node, "smd-edge"); -+ if (edge_node) { -+ edge = qcom_smd_register_edge(dev, edge_node); -+ of_node_put(edge_node); -+ if (IS_ERR(edge)) -+ return dev_err_probe(dev, PTR_ERR(edge), -+ "Failed to register smd-edge\n"); -+ } -+ -+ ret = devm_of_platform_populate(dev); -+ if (ret) { -+ dev_err(dev, "Failed to populate child devices: %d\n", ret); -+ goto err; -+ } -+ -+ platform_set_drvdata(pdev, edge); -+ return 0; -+err: -+ if (edge) -+ qcom_smd_unregister_edge(edge); -+ return ret; -+} -+ -+static void rpm_proc_remove(struct platform_device *pdev) -+{ -+ struct qcom_smd_edge *edge = platform_get_drvdata(pdev); -+ -+ if (edge) -+ qcom_smd_unregister_edge(edge); -+} -+ -+static const struct of_device_id rpm_proc_of_match[] = { -+ { .compatible = "qcom,rpm-proc", }, -+ { /* sentinel */ } -+}; -+MODULE_DEVICE_TABLE(of, rpm_proc_of_match); -+ -+static struct platform_driver rpm_proc_driver = { -+ .probe = rpm_proc_probe, -+ .remove_new = rpm_proc_remove, -+ .driver = { -+ .name = "qcom-rpm-proc", -+ .of_match_table = rpm_proc_of_match, -+ }, -+}; -+ -+static int __init rpm_proc_init(void) -+{ -+ return platform_driver_register(&rpm_proc_driver); -+} -+arch_initcall(rpm_proc_init); -+ -+static void __exit rpm_proc_exit(void) -+{ -+ platform_driver_unregister(&rpm_proc_driver); -+} -+module_exit(rpm_proc_exit); -+ -+MODULE_DESCRIPTION("Qualcomm RPM processor/subsystem driver"); -+MODULE_AUTHOR("Stephan Gerhold "); -+MODULE_LICENSE("GPL"); diff --git a/target/linux/qualcommax/patches-6.1/0051-v6.6-arm64-dts-qcom-Add-rpm-proc-node-for-GLINK.patch b/target/linux/qualcommax/patches-6.1/0051-v6.6-arm64-dts-qcom-Add-rpm-proc-node-for-GLINK.patch deleted file mode 100644 index 746a391b42..0000000000 --- a/target/linux/qualcommax/patches-6.1/0051-v6.6-arm64-dts-qcom-Add-rpm-proc-node-for-GLINK.patch +++ /dev/null @@ -1,93 +0,0 @@ -From 7e1acc8b92a3b67db1e5255adae2851d58d74434 Mon Sep 17 00:00:00 2001 -From: Stephan Gerhold -Date: Thu, 15 Jun 2023 18:50:44 +0200 -Subject: [PATCH] arm64: dts: qcom: Add rpm-proc node for GLINK gplatforms - -Rather than having the RPM GLINK channels as the only child of a dummy -top-level rpm-glink node, switch to representing the RPM as remoteproc -like all the other remoteprocs (modem DSP, ...). - -This allows assigning additional subdevices to it like the MPM -interrupt-controller or rpm-master-stats. - -Tested-by: Konrad Dybcio # SM6375 -Signed-off-by: Stephan Gerhold -Link: https://lore.kernel.org/r/20230531-rpm-rproc-v3-11-a07dcdefd918@gerhold.net -Signed-off-by: Bjorn Andersson ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 48 ++++---- - arch/arm64/boot/dts/qcom/ipq9574.dtsi | 28 +++-- - arch/arm64/boot/dts/qcom/msm8996.dtsi | 113 +++++++++---------- - arch/arm64/boot/dts/qcom/msm8998.dtsi | 102 ++++++++--------- - arch/arm64/boot/dts/qcom/qcm2290.dtsi | 126 ++++++++++----------- - arch/arm64/boot/dts/qcom/qcs404.dtsi | 152 +++++++++++++------------- - arch/arm64/boot/dts/qcom/sdm630.dtsi | 132 +++++++++++----------- - arch/arm64/boot/dts/qcom/sm6115.dtsi | 128 +++++++++++----------- - arch/arm64/boot/dts/qcom/sm6125.dtsi | 140 ++++++++++++------------ - arch/arm64/boot/dts/qcom/sm6375.dtsi | 126 ++++++++++----------- - 10 files changed, 566 insertions(+), 529 deletions(-) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -145,6 +145,32 @@ - method = "smc"; - }; - -+ rpm: remoteproc { -+ compatible = "qcom,ipq6018-rpm-proc", "qcom,rpm-proc"; -+ -+ glink-edge { -+ compatible = "qcom,glink-rpm"; -+ interrupts = ; -+ qcom,rpm-msg-ram = <&rpm_msg_ram>; -+ mboxes = <&apcs_glb 0>; -+ -+ rpm_requests: rpm-requests { -+ compatible = "qcom,rpm-ipq6018"; -+ qcom,glink-channels = "rpm_requests"; -+ -+ regulators { -+ compatible = "qcom,rpm-mp5496-regulators"; -+ -+ ipq6018_s2: s2 { -+ regulator-min-microvolt = <725000>; -+ regulator-max-microvolt = <1062500>; -+ regulator-always-on; -+ }; -+ }; -+ }; -+ }; -+ }; -+ - reserved-memory { - #address-cells = <2>; - #size-cells = <2>; -@@ -181,28 +207,6 @@ - }; - }; - -- rpm-glink { -- compatible = "qcom,glink-rpm"; -- interrupts = ; -- qcom,rpm-msg-ram = <&rpm_msg_ram>; -- mboxes = <&apcs_glb 0>; -- -- rpm_requests: rpm-requests { -- compatible = "qcom,rpm-ipq6018"; -- qcom,glink-channels = "rpm_requests"; -- -- regulators { -- compatible = "qcom,rpm-mp5496-regulators"; -- -- ipq6018_s2: s2 { -- regulator-min-microvolt = <725000>; -- regulator-max-microvolt = <1062500>; -- regulator-always-on; -- }; -- }; -- }; -- }; -- - smem { - compatible = "qcom,smem"; - memory-region = <&smem_region>; diff --git a/target/linux/qualcommax/patches-6.1/0052-v6.7-arm64-dts-qcom-ipq6018-include-the-GPLL0-as.patch b/target/linux/qualcommax/patches-6.1/0052-v6.7-arm64-dts-qcom-ipq6018-include-the-GPLL0-as.patch deleted file mode 100644 index b70d7bf69c..0000000000 --- a/target/linux/qualcommax/patches-6.1/0052-v6.7-arm64-dts-qcom-ipq6018-include-the-GPLL0-as.patch +++ /dev/null @@ -1,35 +0,0 @@ -From 0133c7af3aa0420778d106cb90db708cfa45f2c6 Mon Sep 17 00:00:00 2001 -From: Kathiravan Thirumoorthy -Date: Thu, 14 Sep 2023 12:29:59 +0530 -Subject: [PATCH] arm64: dts: qcom: ipq6018: include the GPLL0 as clock - provider for mailbox - -While the kernel is booting up, APSS clock / CPU clock will be running -at 800MHz with GPLL0 as source. Once the cpufreq driver is available, -APSS PLL will be configured to the rate based on the opp table and the -source also will be changed to APSS_PLL_EARLY. So allow the mailbox to -consume the GPLL0, with this inclusion, CPU Freq correctly reports that -CPU is running at 800MHz rather than 24MHz. - -Signed-off-by: Kathiravan Thirumoorthy -Reviewed-by: Konrad Dybcio -Link: https://lore.kernel.org/r/20230913-gpll_cleanup-v2-9-c8ceb1a37680@quicinc.com -[bjorn: Updated commit message, as requested by Kathiravan] -Signed-off-by: Bjorn Andersson ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 4 ++-- - 1 file changed, 2 insertions(+), 2 deletions(-) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -618,8 +618,8 @@ - compatible = "qcom,ipq6018-apcs-apps-global"; - reg = <0x0 0x0b111000 0x0 0x1000>; - #clock-cells = <1>; -- clocks = <&a53pll>, <&xo>; -- clock-names = "pll", "xo"; -+ clocks = <&a53pll>, <&xo>, <&gcc GPLL0>; -+ clock-names = "pll", "xo", "gpll0"; - #mbox-cells = <1>; - }; - diff --git a/target/linux/qualcommax/patches-6.1/0053-v6.7-clk-qcom-gcc-ipq6018-add-QUP6-I2C-clock.patch b/target/linux/qualcommax/patches-6.1/0053-v6.7-clk-qcom-gcc-ipq6018-add-QUP6-I2C-clock.patch deleted file mode 100644 index 0858528933..0000000000 --- a/target/linux/qualcommax/patches-6.1/0053-v6.7-clk-qcom-gcc-ipq6018-add-QUP6-I2C-clock.patch +++ /dev/null @@ -1,57 +0,0 @@ -From 3dcf7b59393812a5fbd83f8cd8d34b94afb4c4d1 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Sat, 21 Oct 2023 13:55:18 +0200 -Subject: [PATCH] clk: qcom: gcc-ipq6018: add QUP6 I2C clock - -QUP6 I2C clock is listed in the dt bindings but it was never included in -the GCC driver. -So lets add support for it, it is marked as criticial as it is used by RPM -to communicate to the external PMIC over I2C so this clock must not be -disabled. - -Signed-off-by: Robert Marko -Reviewed-by: Kathiravan Thirumoorthy -Reviewed-by: Konrad Dybcio -Link: https://lore.kernel.org/r/20231021115545.229060-1-robimarko@gmail.com -Signed-off-by: Bjorn Andersson ---- - drivers/clk/qcom/gcc-ipq6018.c | 21 +++++++++++++++++++++ - 1 file changed, 21 insertions(+) - ---- a/drivers/clk/qcom/gcc-ipq6018.c -+++ b/drivers/clk/qcom/gcc-ipq6018.c -@@ -2120,6 +2120,26 @@ static struct clk_branch gcc_blsp1_qup5_ - }, - }; - -+static struct clk_branch gcc_blsp1_qup6_i2c_apps_clk = { -+ .halt_reg = 0x07010, -+ .clkr = { -+ .enable_reg = 0x07010, -+ .enable_mask = BIT(0), -+ .hw.init = &(struct clk_init_data){ -+ .name = "gcc_blsp1_qup6_i2c_apps_clk", -+ .parent_hws = (const struct clk_hw *[]){ -+ &blsp1_qup6_i2c_apps_clk_src.clkr.hw }, -+ .num_parents = 1, -+ /* -+ * RPM uses QUP6 I2C to communicate with the external -+ * PMIC so it must not be disabled. -+ */ -+ .flags = CLK_SET_RATE_PARENT | CLK_IS_CRITICAL, -+ .ops = &clk_branch2_ops, -+ }, -+ }, -+}; -+ - static struct clk_branch gcc_blsp1_qup6_spi_apps_clk = { - .halt_reg = 0x0700c, - .clkr = { -@@ -4276,6 +4296,7 @@ static struct clk_regmap *gcc_ipq6018_cl - [GCC_BLSP1_QUP4_SPI_APPS_CLK] = &gcc_blsp1_qup4_spi_apps_clk.clkr, - [GCC_BLSP1_QUP5_I2C_APPS_CLK] = &gcc_blsp1_qup5_i2c_apps_clk.clkr, - [GCC_BLSP1_QUP5_SPI_APPS_CLK] = &gcc_blsp1_qup5_spi_apps_clk.clkr, -+ [GCC_BLSP1_QUP6_I2C_APPS_CLK] = &gcc_blsp1_qup6_i2c_apps_clk.clkr, - [GCC_BLSP1_QUP6_SPI_APPS_CLK] = &gcc_blsp1_qup6_spi_apps_clk.clkr, - [GCC_BLSP1_UART1_APPS_CLK] = &gcc_blsp1_uart1_apps_clk.clkr, - [GCC_BLSP1_UART2_APPS_CLK] = &gcc_blsp1_uart2_apps_clk.clkr, diff --git a/target/linux/qualcommax/patches-6.1/0054-v6.8-arm64-dts-qcom-ipq6018-use-CPUFreq-NVMEM.patch b/target/linux/qualcommax/patches-6.1/0054-v6.8-arm64-dts-qcom-ipq6018-use-CPUFreq-NVMEM.patch deleted file mode 100644 index 1369a90a8a..0000000000 --- a/target/linux/qualcommax/patches-6.1/0054-v6.8-arm64-dts-qcom-ipq6018-use-CPUFreq-NVMEM.patch +++ /dev/null @@ -1,85 +0,0 @@ -From 83afcf14edb9217e58837eb119da96d734a4b3b1 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Sat, 21 Oct 2023 14:00:07 +0200 -Subject: [PATCH] arm64: dts: qcom: ipq6018: use CPUFreq NVMEM - -IPQ6018 comes in multiple SKU-s and some of them dont support all of the -OPP-s that are current set, so lets utilize CPUFreq NVMEM to allow only -supported OPP-s based on the SoC dynamically. - -As an example, IPQ6018 is generaly rated at 1.8GHz but some silicon only -goes up to 1.5GHz and is marked as such via an eFuse. - -Signed-off-by: Robert Marko -Reviewed-by: Konrad Dybcio -Link: https://lore.kernel.org/r/20231021120048.231239-1-robimarko@gmail.com -Signed-off-by: Bjorn Andersson ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 14 +++++++++++++- - 1 file changed, 13 insertions(+), 1 deletion(-) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -95,42 +95,49 @@ - }; - - cpu_opp_table: opp-table-cpu { -- compatible = "operating-points-v2"; -+ compatible = "operating-points-v2-kryo-cpu"; -+ nvmem-cells = <&cpu_speed_bin>; - opp-shared; - - opp-864000000 { - opp-hz = /bits/ 64 <864000000>; - opp-microvolt = <725000>; -+ opp-supported-hw = <0xf>; - clock-latency-ns = <200000>; - }; - - opp-1056000000 { - opp-hz = /bits/ 64 <1056000000>; - opp-microvolt = <787500>; -+ opp-supported-hw = <0xf>; - clock-latency-ns = <200000>; - }; - - opp-1320000000 { - opp-hz = /bits/ 64 <1320000000>; - opp-microvolt = <862500>; -+ opp-supported-hw = <0x3>; - clock-latency-ns = <200000>; - }; - - opp-1440000000 { - opp-hz = /bits/ 64 <1440000000>; - opp-microvolt = <925000>; -+ opp-supported-hw = <0x3>; - clock-latency-ns = <200000>; - }; - - opp-1608000000 { - opp-hz = /bits/ 64 <1608000000>; - opp-microvolt = <987500>; -+ opp-supported-hw = <0x1>; - clock-latency-ns = <200000>; - }; - - opp-1800000000 { - opp-hz = /bits/ 64 <1800000000>; - opp-microvolt = <1062500>; -+ opp-supported-hw = <0x1>; - clock-latency-ns = <200000>; - }; - }; -@@ -321,6 +328,11 @@ - reg = <0x0 0x000a4000 0x0 0x2000>; - #address-cells = <1>; - #size-cells = <1>; -+ -+ cpu_speed_bin: cpu-speed-bin@135 { -+ reg = <0x135 0x1>; -+ bits = <7 1>; -+ }; - }; - - prng: qrng@e3000 { diff --git a/target/linux/qualcommax/patches-6.1/0055-v6.8-arm64-dts-ipq6018-Add-remaining-QUP-UART-node.patch b/target/linux/qualcommax/patches-6.1/0055-v6.8-arm64-dts-ipq6018-Add-remaining-QUP-UART-node.patch deleted file mode 100644 index ca3c896047..0000000000 --- a/target/linux/qualcommax/patches-6.1/0055-v6.8-arm64-dts-ipq6018-Add-remaining-QUP-UART-node.patch +++ /dev/null @@ -1,81 +0,0 @@ -From e6c32770ef83f3e8cc057f3920b1c06aa9d1c9c2 Mon Sep 17 00:00:00 2001 -From: Chukun Pan -Date: Sun, 3 Dec 2023 23:39:14 +0800 -Subject: [PATCH] arm64: dts: qcom: ipq6018: Add remaining QUP UART node - -Add node to support all the QUP UART node controller inside of IPQ6018. -Some routers use these bus to connect Bluetooth chips. - -Signed-off-by: Chukun Pan -Link: https://lore.kernel.org/r/20231203153914.532654-1-amadeus@jmu.edu.cn -Signed-off-by: Bjorn Andersson ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 50 +++++++++++++++++++++++++++ - 1 file changed, 50 insertions(+) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -458,6 +458,26 @@ - qcom,ee = <0>; - }; - -+ blsp1_uart1: serial@78af000 { -+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; -+ reg = <0x0 0x78af000 0x0 0x200>; -+ interrupts = ; -+ clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, -+ <&gcc GCC_BLSP1_AHB_CLK>; -+ clock-names = "core", "iface"; -+ status = "disabled"; -+ }; -+ -+ blsp1_uart2: serial@78b0000 { -+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; -+ reg = <0x0 0x78b0000 0x0 0x200>; -+ interrupts = ; -+ clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, -+ <&gcc GCC_BLSP1_AHB_CLK>; -+ clock-names = "core", "iface"; -+ status = "disabled"; -+ }; -+ - blsp1_uart3: serial@78b1000 { - compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; - reg = <0x0 0x078b1000 0x0 0x200>; -@@ -466,6 +486,36 @@ - <&gcc GCC_BLSP1_AHB_CLK>; - clock-names = "core", "iface"; - status = "disabled"; -+ }; -+ -+ blsp1_uart4: serial@78b2000 { -+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; -+ reg = <0x0 0x078b2000 0x0 0x200>; -+ interrupts = ; -+ clocks = <&gcc GCC_BLSP1_UART4_APPS_CLK>, -+ <&gcc GCC_BLSP1_AHB_CLK>; -+ clock-names = "core", "iface"; -+ status = "disabled"; -+ }; -+ -+ blsp1_uart5: serial@78b3000 { -+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; -+ reg = <0x0 0x78b3000 0x0 0x200>; -+ interrupts = ; -+ clocks = <&gcc GCC_BLSP1_UART5_APPS_CLK>, -+ <&gcc GCC_BLSP1_AHB_CLK>; -+ clock-names = "core", "iface"; -+ status = "disabled"; -+ }; -+ -+ blsp1_uart6: serial@78b4000 { -+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; -+ reg = <0x0 0x078b4000 0x0 0x200>; -+ interrupts = ; -+ clocks = <&gcc GCC_BLSP1_UART6_APPS_CLK>, -+ <&gcc GCC_BLSP1_AHB_CLK>; -+ clock-names = "core", "iface"; -+ status = "disabled"; - }; - - blsp1_spi1: spi@78b5000 { diff --git a/target/linux/qualcommax/patches-6.1/0056-v6.9-arm64-dts-qcom-Fix-hs_phy_irq-for-QUSB2-targets.patch b/target/linux/qualcommax/patches-6.1/0056-v6.9-arm64-dts-qcom-Fix-hs_phy_irq-for-QUSB2-targets.patch deleted file mode 100644 index 0f1b3e6a38..0000000000 --- a/target/linux/qualcommax/patches-6.1/0056-v6.9-arm64-dts-qcom-Fix-hs_phy_irq-for-QUSB2-targets.patch +++ /dev/null @@ -1,95 +0,0 @@ -From 2c6597c72e9722ac020102d5af40126df0437b82 Mon Sep 17 00:00:00 2001 -From: Krishna Kurapati -Date: Fri, 26 Jan 2024 00:29:18 +0530 -Subject: [PATCH] arm64: dts: qcom: Fix hs_phy_irq for QUSB2 targets - -On several QUSB2 Targets, the hs_phy_irq mentioned is actually -qusb2_phy interrupt specific to QUSB2 PHY's. Rename hs_phy_irq -to qusb2_phy for such targets. - -In actuality, the hs_phy_irq is also present in these targets, but -kept in for debug purposes in hw test environments. This is not -triggered by default and its functionality is mutually exclusive -to that of qusb2_phy interrupt. - -Add missing hs_phy_irq's, pwr_event irq's for QUSB2 PHY targets. -Add missing ss_phy_irq on some targets which allows for remote -wakeup to work on a Super Speed link. - -Also modify order of interrupts in accordance to bindings update. -Since driver looks up for interrupts by name and not by index, it -is safe to modify order of these interrupts in the DT. - -Signed-off-by: Krishna Kurapati -Link: https://lore.kernel.org/r/20240125185921.5062-2-quic_kriskura@quicinc.com -Signed-off-by: Bjorn Andersson ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 13 +++++++++++++ - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 14 ++++++++++++++ - arch/arm64/boot/dts/qcom/msm8953.dtsi | 7 +++++-- - arch/arm64/boot/dts/qcom/msm8996.dtsi | 8 ++++++-- - arch/arm64/boot/dts/qcom/msm8998.dtsi | 7 +++++-- - arch/arm64/boot/dts/qcom/sdm630.dtsi | 17 +++++++++++++---- - arch/arm64/boot/dts/qcom/sm6115.dtsi | 9 +++++++-- - arch/arm64/boot/dts/qcom/sm6125.dtsi | 9 +++++++-- - 8 files changed, 70 insertions(+), 14 deletions(-) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -430,6 +430,12 @@ - <&gcc GCC_USB1_MOCK_UTMI_CLK>; - assigned-clock-rates = <133330000>, - <24000000>; -+ -+ interrupts = , -+ ; -+ interrupt-names = "pwr_event", -+ "qusb2_phy"; -+ - resets = <&gcc GCC_USB1_BCR>; - status = "disabled"; - -@@ -628,6 +634,13 @@ - <133330000>, - <24000000>; - -+ interrupts = , -+ , -+ ; -+ interrupt-names = "pwr_event", -+ "qusb2_phy", -+ "ss_phy_irq"; -+ - resets = <&gcc GCC_USB0_BCR>; - status = "disabled"; - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -611,6 +611,13 @@ - <133330000>, - <19200000>; - -+ interrupts = , -+ , -+ ; -+ interrupt-names = "pwr_event", -+ "qusb2_phy", -+ "ss_phy_irq"; -+ - power-domains = <&gcc USB0_GDSC>; - - resets = <&gcc GCC_USB0_BCR>; -@@ -653,6 +660,13 @@ - <133330000>, - <19200000>; - -+ interrupts = , -+ , -+ ; -+ interrupt-names = "pwr_event", -+ "qusb2_phy", -+ "ss_phy_irq"; -+ - power-domains = <&gcc USB1_GDSC>; - - resets = <&gcc GCC_USB1_BCR>; diff --git a/target/linux/qualcommax/patches-6.1/0057-v6.8-hwspinlock-qcom-Remove-IPQ6018-SOC-specific-.patch b/target/linux/qualcommax/patches-6.1/0057-v6.8-hwspinlock-qcom-Remove-IPQ6018-SOC-specific-.patch deleted file mode 100644 index 25d56870a4..0000000000 --- a/target/linux/qualcommax/patches-6.1/0057-v6.8-hwspinlock-qcom-Remove-IPQ6018-SOC-specific-.patch +++ /dev/null @@ -1,32 +0,0 @@ -From c3dc3d079d191c9149496b3c7fe1ece909386d93 Mon Sep 17 00:00:00 2001 -From: Vignesh Viswanathan -Date: Tue, 5 Sep 2023 15:25:35 +0530 -Subject: [PATCH] hwspinlock: qcom: Remove IPQ6018 SOC specific compatible - -IPQ6018 has 32 tcsr_mutex hwlock registers with stride 0x1000. -The compatible string qcom,ipq6018-tcsr-mutex is mapped to -of_msm8226_tcsr_mutex which has 32 locks configured with stride of 0x80 -and doesn't match the HW present in IPQ6018. - -Remove IPQ6018 specific compatible string so that it fallsback to -of_tcsr_mutex data which maps to the correct configuration for IPQ6018. - -Fixes: 5d4753f741d8 ("hwspinlock: qcom: add support for MMIO on older SoCs") -Signed-off-by: Vignesh Viswanathan -Reviewed-by: Konrad Dybcio -Link: https://lore.kernel.org/r/20230905095535.1263113-3-quic_viswanat@quicinc.com -Signed-off-by: Bjorn Andersson ---- - drivers/hwspinlock/qcom_hwspinlock.c | 1 - - 1 file changed, 1 deletion(-) - ---- a/drivers/hwspinlock/qcom_hwspinlock.c -+++ b/drivers/hwspinlock/qcom_hwspinlock.c -@@ -115,7 +115,6 @@ static const struct of_device_id qcom_hw - { .compatible = "qcom,sfpb-mutex", .data = &of_sfpb_mutex }, - { .compatible = "qcom,tcsr-mutex", .data = &of_tcsr_mutex }, - { .compatible = "qcom,apq8084-tcsr-mutex", .data = &of_msm8226_tcsr_mutex }, -- { .compatible = "qcom,ipq6018-tcsr-mutex", .data = &of_msm8226_tcsr_mutex }, - { .compatible = "qcom,msm8226-tcsr-mutex", .data = &of_msm8226_tcsr_mutex }, - { .compatible = "qcom,msm8974-tcsr-mutex", .data = &of_msm8226_tcsr_mutex }, - { .compatible = "qcom,msm8994-tcsr-mutex", .data = &of_msm8226_tcsr_mutex }, diff --git a/target/linux/qualcommax/patches-6.1/0058-v6.9-arm64-dts-qcom-ipq6018-add-tsens-node.patch b/target/linux/qualcommax/patches-6.1/0058-v6.9-arm64-dts-qcom-ipq6018-add-tsens-node.patch deleted file mode 100644 index 9de90e4da6..0000000000 --- a/target/linux/qualcommax/patches-6.1/0058-v6.9-arm64-dts-qcom-ipq6018-add-tsens-node.patch +++ /dev/null @@ -1,34 +0,0 @@ -From 0b17197055b528da22e9385200e61b847b499d48 Mon Sep 17 00:00:00 2001 -From: Mantas Pucka -Date: Thu, 25 Jan 2024 11:04:11 +0200 -Subject: [PATCH] arm64: dts: qcom: ipq6018: add tsens node - -IPQ6018 has temperature sensing HW block compatible with IPQ8074. Add -node for it. - -Signed-off-by: Mantas Pucka -Link: https://lore.kernel.org/r/1706173452-1017-3-git-send-email-mantas@8devices.com -Signed-off-by: Bjorn Andersson ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 10 ++++++++++ - 1 file changed, 10 insertions(+) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -342,6 +342,16 @@ - clock-names = "core"; - }; - -+ tsens: thermal-sensor@4a9000 { -+ compatible = "qcom,ipq6018-tsens", "qcom,ipq8074-tsens"; -+ reg = <0x0 0x004a9000 0x0 0x1000>, -+ <0x0 0x004a8000 0x0 0x1000>; -+ interrupts = ; -+ interrupt-names = "combined"; -+ #qcom,sensors = <16>; -+ #thermal-sensor-cells = <1>; -+ }; -+ - cryptobam: dma-controller@704000 { - compatible = "qcom,bam-v1.7.0"; - reg = <0x0 0x00704000 0x0 0x20000>; diff --git a/target/linux/qualcommax/patches-6.1/0059-v6.9-arm64-dts-qcom-ipq6018-add-thermal-zones.patch b/target/linux/qualcommax/patches-6.1/0059-v6.9-arm64-dts-qcom-ipq6018-add-thermal-zones.patch deleted file mode 100644 index dab433348a..0000000000 --- a/target/linux/qualcommax/patches-6.1/0059-v6.9-arm64-dts-qcom-ipq6018-add-thermal-zones.patch +++ /dev/null @@ -1,180 +0,0 @@ -From 8f053e5616352943e16966f195f5a7a161e6fe7d Mon Sep 17 00:00:00 2001 -From: Mantas Pucka -Date: Thu, 25 Jan 2024 11:04:12 +0200 -Subject: [PATCH] arm64: dts: qcom: ipq6018: add thermal zones - -Add thermal zones to make use of thermal sensors data. For CPU zone, -add cooling device that uses CPU frequency scaling. - -Signed-off-by: Mantas Pucka -Link: https://lore.kernel.org/r/1706173452-1017-4-git-send-email-mantas@8devices.com -Signed-off-by: Bjorn Andersson ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 121 ++++++++++++++++++++++++++ - 1 file changed, 121 insertions(+) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -9,6 +9,7 @@ - #include - #include - #include -+#include - - / { - #address-cells = <2>; -@@ -43,6 +44,7 @@ - clock-names = "cpu"; - operating-points-v2 = <&cpu_opp_table>; - cpu-supply = <&ipq6018_s2>; -+ #cooling-cells = <2>; - }; - - CPU1: cpu@1 { -@@ -55,6 +57,7 @@ - clock-names = "cpu"; - operating-points-v2 = <&cpu_opp_table>; - cpu-supply = <&ipq6018_s2>; -+ #cooling-cells = <2>; - }; - - CPU2: cpu@2 { -@@ -67,6 +70,7 @@ - clock-names = "cpu"; - operating-points-v2 = <&cpu_opp_table>; - cpu-supply = <&ipq6018_s2>; -+ #cooling-cells = <2>; - }; - - CPU3: cpu@3 { -@@ -79,6 +83,7 @@ - clock-names = "cpu"; - operating-points-v2 = <&cpu_opp_table>; - cpu-supply = <&ipq6018_s2>; -+ #cooling-cells = <2>; - }; - - L2_0: l2-cache { -@@ -888,6 +893,122 @@ - }; - }; - -+ thermal-zones { -+ nss-top-thermal { -+ polling-delay-passive = <250>; -+ polling-delay = <1000>; -+ thermal-sensors = <&tsens 4>; -+ -+ trips { -+ nss-top-critical { -+ temperature = <125000>; -+ hysteresis = <1000>; -+ type = "critical"; -+ }; -+ }; -+ }; -+ -+ nss-thermal { -+ polling-delay-passive = <250>; -+ polling-delay = <1000>; -+ thermal-sensors = <&tsens 5>; -+ -+ trips { -+ nss-critical { -+ temperature = <125000>; -+ hysteresis = <1000>; -+ type = "critical"; -+ }; -+ }; -+ }; -+ -+ wcss-phya0-thermal { -+ polling-delay-passive = <250>; -+ polling-delay = <1000>; -+ thermal-sensors = <&tsens 7>; -+ -+ trips { -+ wcss-phya0-critical { -+ temperature = <125000>; -+ hysteresis = <1000>; -+ type = "critical"; -+ }; -+ }; -+ }; -+ -+ wcss-phya1-thermal { -+ polling-delay-passive = <250>; -+ polling-delay = <1000>; -+ thermal-sensors = <&tsens 8>; -+ -+ trips { -+ wcss-phya1-critical { -+ temperature = <125000>; -+ hysteresis = <1000>; -+ type = "critical"; -+ }; -+ }; -+ }; -+ -+ cpu-thermal { -+ polling-delay-passive = <250>; -+ polling-delay = <1000>; -+ thermal-sensors = <&tsens 13>; -+ -+ trips { -+ cpu-critical { -+ temperature = <125000>; -+ hysteresis = <1000>; -+ type = "critical"; -+ }; -+ -+ cpu_alert: cpu-passive { -+ temperature = <110000>; -+ hysteresis = <1000>; -+ type = "passive"; -+ }; -+ }; -+ -+ cooling-maps { -+ map0 { -+ trip = <&cpu_alert>; -+ cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, -+ <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, -+ <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, -+ <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; -+ }; -+ }; -+ }; -+ -+ lpass-thermal { -+ polling-delay-passive = <250>; -+ polling-delay = <1000>; -+ thermal-sensors = <&tsens 14>; -+ -+ trips { -+ lpass-critical { -+ temperature = <125000>; -+ hysteresis = <1000>; -+ type = "critical"; -+ }; -+ }; -+ }; -+ -+ ddrss-top-thermal { -+ polling-delay-passive = <250>; -+ polling-delay = <1000>; -+ thermal-sensors = <&tsens 15>; -+ -+ trips { -+ ddrss-top-critical { -+ temperature = <125000>; -+ hysteresis = <1000>; -+ type = "critical"; -+ }; -+ }; -+ }; -+ }; -+ - timer { - compatible = "arm,armv8-timer"; - interrupts = , diff --git a/target/linux/qualcommax/patches-6.1/0060-v6.9-clk-qcom-gcc-ipq6018-add-qdss_at-clock-needed-for-wi.patch b/target/linux/qualcommax/patches-6.1/0060-v6.9-clk-qcom-gcc-ipq6018-add-qdss_at-clock-needed-for-wi.patch deleted file mode 100644 index e72d1180c5..0000000000 --- a/target/linux/qualcommax/patches-6.1/0060-v6.9-clk-qcom-gcc-ipq6018-add-qdss_at-clock-needed-for-wi.patch +++ /dev/null @@ -1,50 +0,0 @@ -From fd712118aa1aa758da1fd1546b3f8a1b00e42cbc Mon Sep 17 00:00:00 2001 -From: Mantas Pucka -Date: Tue, 23 Jan 2024 11:26:09 +0200 -Subject: [PATCH] clk: qcom: gcc-ipq6018: add qdss_at clock needed for wifi - operation - -Without it system hangs upon wifi firmware load. It should be enabled by -remoteproc/wifi driver. Bindings already exist for it, so add it based -on vendor code. - -Signed-off-by: Mantas Pucka -Link: https://lore.kernel.org/r/1706001970-26032-1-git-send-email-mantas@8devices.com -Signed-off-by: Bjorn Andersson ---- - drivers/clk/qcom/gcc-ipq6018.c | 17 +++++++++++++++++ - 1 file changed, 17 insertions(+) - ---- a/drivers/clk/qcom/gcc-ipq6018.c -+++ b/drivers/clk/qcom/gcc-ipq6018.c -@@ -3523,6 +3523,22 @@ static struct clk_branch gcc_prng_ahb_cl - }, - }; - -+static struct clk_branch gcc_qdss_at_clk = { -+ .halt_reg = 0x29024, -+ .clkr = { -+ .enable_reg = 0x29024, -+ .enable_mask = BIT(0), -+ .hw.init = &(struct clk_init_data){ -+ .name = "gcc_qdss_at_clk", -+ .parent_hws = (const struct clk_hw *[]){ -+ &qdss_at_clk_src.clkr.hw }, -+ .num_parents = 1, -+ .flags = CLK_SET_RATE_PARENT, -+ .ops = &clk_branch2_ops, -+ }, -+ }, -+}; -+ - static struct clk_branch gcc_qdss_dap_clk = { - .halt_reg = 0x29084, - .clkr = { -@@ -4362,6 +4378,7 @@ static struct clk_regmap *gcc_ipq6018_cl - [GCC_SYS_NOC_PCIE0_AXI_CLK] = &gcc_sys_noc_pcie0_axi_clk.clkr, - [GCC_PCIE0_PIPE_CLK] = &gcc_pcie0_pipe_clk.clkr, - [GCC_PRNG_AHB_CLK] = &gcc_prng_ahb_clk.clkr, -+ [GCC_QDSS_AT_CLK] = &gcc_qdss_at_clk.clkr, - [GCC_QDSS_DAP_CLK] = &gcc_qdss_dap_clk.clkr, - [GCC_QPIC_AHB_CLK] = &gcc_qpic_ahb_clk.clkr, - [GCC_QPIC_CLK] = &gcc_qpic_clk.clkr, diff --git a/target/linux/qualcommax/patches-6.1/0061-v6.8-phy-qcom-qmp-usb-fix-serdes-init-sequence-for-IPQ6018.patch b/target/linux/qualcommax/patches-6.1/0061-v6.8-phy-qcom-qmp-usb-fix-serdes-init-sequence-for-IPQ6018.patch deleted file mode 100644 index 97b46f74ef..0000000000 --- a/target/linux/qualcommax/patches-6.1/0061-v6.8-phy-qcom-qmp-usb-fix-serdes-init-sequence-for-IPQ6018.patch +++ /dev/null @@ -1,102 +0,0 @@ -From 62a5df451ab911421da96655fcc4d1e269ff6e2f Mon Sep 17 00:00:00 2001 -From: Mantas Pucka -Date: Tue, 23 Jan 2024 18:09:20 +0200 -Subject: [PATCH] phy: qcom-qmp-usb: fix serdes init sequence for IPQ6018 - -Commit 23fd679249df ("phy: qcom-qmp: add USB3 PHY support for IPQ6018") -noted that IPQ6018 init is identical to IPQ8074. Yet downstream uses -separate serdes init sequence for IPQ6018. Since already existing IPQ9574 -serdes init sequence is identical, just reuse it and fix failing USB3 mode -in IPQ6018. - -Fixes: 23fd679249df ("phy: qcom-qmp: add USB3 PHY support for IPQ6018") -Signed-off-by: Mantas Pucka -Reviewed-by: Dmitry Baryshkov -Link: https://lore.kernel.org/r/1706026160-17520-3-git-send-email-mantas@8devices.com -Signed-off-by: Vinod Koul ---- - drivers/phy/qualcomm/phy-qcom-qmp-usb.c | 20 +++++++++++++++++++- - 1 file changed, 19 insertions(+), 1 deletion(-) - ---- a/drivers/phy/qualcomm/phy-qcom-qmp-usb.c -+++ b/drivers/phy/qualcomm/phy-qcom-qmp-usb.c -@@ -233,6 +233,43 @@ static const struct qmp_phy_init_tbl ipq - QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V0, 0x0f), - }; - -+static const struct qmp_phy_init_tbl ipq9574_usb3_serdes_tbl[] = { -+ QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0x1a), -+ QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x08), -+ QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x30), -+ QMP_PHY_INIT_CFG(QSERDES_COM_BG_TRIM, 0x0f), -+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_FASTLOCK_FO_GAIN, 0x0b), -+ QMP_PHY_INIT_CFG(QSERDES_COM_SVS_MODE_CLK_SEL, 0x01), -+ QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x00), -+ QMP_PHY_INIT_CFG(QSERDES_COM_CMN_CONFIG, 0x06), -+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_IVCO, 0x0f), -+ QMP_PHY_INIT_CFG(QSERDES_COM_SYS_CLK_CTRL, 0x06), -+ /* PLL and Loop filter settings */ -+ QMP_PHY_INIT_CFG(QSERDES_COM_DEC_START_MODE0, 0x68), -+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START1_MODE0, 0xab), -+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START2_MODE0, 0xaa), -+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x02), -+ QMP_PHY_INIT_CFG(QSERDES_COM_CP_CTRL_MODE0, 0x09), -+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_RCTRL_MODE0, 0x16), -+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_CCTRL_MODE0, 0x28), -+ QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0xa0), -+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP1_MODE0, 0xaa), -+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP2_MODE0, 0x29), -+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP3_MODE0, 0x00), -+ QMP_PHY_INIT_CFG(QSERDES_COM_CORE_CLK_EN, 0x00), -+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP_CFG, 0x00), -+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_MAP, 0x00), -+ QMP_PHY_INIT_CFG(QSERDES_COM_BG_TIMER, 0x0a), -+ /* SSC settings */ -+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_EN_CENTER, 0x01), -+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER1, 0x7d), -+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER2, 0x01), -+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER1, 0x00), -+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER2, 0x00), -+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE1, 0x0a), -+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE2, 0x05), -+}; -+ - static const struct qmp_phy_init_tbl msm8996_usb3_serdes_tbl[] = { - QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0x14), - QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x08), -@@ -1591,6 +1628,26 @@ static const char * const qmp_phy_vreg_l - "vdda-phy", "vdda-pll", - }; - -+static const struct qmp_phy_cfg ipq6018_usb3phy_cfg = { -+ .lanes = 1, -+ -+ .serdes_tbl = ipq9574_usb3_serdes_tbl, -+ .serdes_tbl_num = ARRAY_SIZE(ipq9574_usb3_serdes_tbl), -+ .tx_tbl = msm8996_usb3_tx_tbl, -+ .tx_tbl_num = ARRAY_SIZE(msm8996_usb3_tx_tbl), -+ .rx_tbl = ipq8074_usb3_rx_tbl, -+ .rx_tbl_num = ARRAY_SIZE(ipq8074_usb3_rx_tbl), -+ .pcs_tbl = ipq8074_usb3_pcs_tbl, -+ .pcs_tbl_num = ARRAY_SIZE(ipq8074_usb3_pcs_tbl), -+ .clk_list = msm8996_phy_clk_l, -+ .num_clks = ARRAY_SIZE(msm8996_phy_clk_l), -+ .reset_list = msm8996_usb3phy_reset_l, -+ .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l), -+ .vreg_list = qmp_phy_vreg_l, -+ .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), -+ .regs = qmp_v3_usb3phy_regs_layout, -+}; -+ - static const struct qmp_phy_cfg ipq8074_usb3phy_cfg = { - .lanes = 1, - -@@ -2534,7 +2591,7 @@ static const struct of_device_id qmp_usb - .data = &msm8996_usb3phy_cfg, - }, { - .compatible = "qcom,ipq6018-qmp-usb3-phy", -- .data = &ipq8074_usb3phy_cfg, -+ .data = &ipq6018_usb3phy_cfg, - }, { - .compatible = "qcom,sc7180-qmp-usb3-phy", - .data = &sc7180_usb3phy_cfg, diff --git a/target/linux/qualcommax/patches-6.1/0062-v6.8-arm64-dts-qcom-ipq8074-Add-QUP4-SPI-node.patch b/target/linux/qualcommax/patches-6.1/0062-v6.8-arm64-dts-qcom-ipq8074-Add-QUP4-SPI-node.patch deleted file mode 100644 index 1525726640..0000000000 --- a/target/linux/qualcommax/patches-6.1/0062-v6.8-arm64-dts-qcom-ipq8074-Add-QUP4-SPI-node.patch +++ /dev/null @@ -1,38 +0,0 @@ -From 6a25e70214fde6dcf900271c819c8d7fe7b9a4b0 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Thu, 23 Nov 2023 13:12:54 +0100 -Subject: [PATCH] arm64: dts: qcom: ipq8074: Add QUP4 SPI node - -Add node to support the QUP4 SPI controller inside of IPQ8074. -Some devices use this bus to communicate to a Bluetooth controller. - -Signed-off-by: Robert Marko -Link: https://lore.kernel.org/r/20231123121324.1046164-1-robimarko@gmail.com -Signed-off-by: Bjorn Andersson ---- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 14 ++++++++++++++ - 1 file changed, 14 insertions(+) - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -529,6 +529,20 @@ - status = "disabled"; - }; - -+ blsp1_spi4: spi@78b8000 { -+ compatible = "qcom,spi-qup-v2.2.1"; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ reg = <0x78b8000 0x600>; -+ interrupts = ; -+ clocks = <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>, -+ <&gcc GCC_BLSP1_AHB_CLK>; -+ clock-names = "core", "iface"; -+ dmas = <&blsp_dma 18>, <&blsp_dma 19>; -+ dma-names = "tx", "rx"; -+ status = "disabled"; -+ }; -+ - blsp1_i2c5: i2c@78b9000 { - compatible = "qcom,i2c-qup-v2.2.1"; - #address-cells = <1>; diff --git a/target/linux/qualcommax/patches-6.1/0100-clk-qcom-clk-rcg2-introduce-support-for-multiple-con.patch b/target/linux/qualcommax/patches-6.1/0100-clk-qcom-clk-rcg2-introduce-support-for-multiple-con.patch deleted file mode 100644 index 9aa0a7952c..0000000000 --- a/target/linux/qualcommax/patches-6.1/0100-clk-qcom-clk-rcg2-introduce-support-for-multiple-con.patch +++ /dev/null @@ -1,203 +0,0 @@ -From 032be4f49dda786fea9e1501212f6cd09a7ded96 Mon Sep 17 00:00:00 2001 -From: Christian Marangi -Date: Thu, 3 Nov 2022 14:49:43 +0100 -Subject: [PATCH] clk: qcom: clk-rcg2: introduce support for multiple conf for - same freq - -Some RCG frequency can be reached by multiple configuration. - -We currently declare multiple configuration for the same frequency but -that is not supported and always the first configuration will be taken. - -These multiple configuration are needed as based on the current parent -configuration, it may be needed to use a different configuration to -reach the same frequency. - -To handle this introduce 2 new macro, FM and C. - -- FM is used to declare an empty freq_tbl with just the frequency and an - array of confs to insert all the config for the provided frequency. - -- C is used to declare a fre_conf where src, pre_div, m and n are - provided. - -The driver is changed to handle this special freq_tbl and select the -correct config by calculating the final rate and deciding based on the -one that is less different than the requested one. - -Tested-by: Robert Marko -Signed-off-by: Christian Marangi ---- - drivers/clk/qcom/clk-rcg.h | 14 ++++++- - drivers/clk/qcom/clk-rcg2.c | 84 +++++++++++++++++++++++++++++++++---- - 2 files changed, 88 insertions(+), 10 deletions(-) - ---- a/drivers/clk/qcom/clk-rcg.h -+++ b/drivers/clk/qcom/clk-rcg.h -@@ -7,7 +7,17 @@ - #include - #include "clk-regmap.h" - --#define F(f, s, h, m, n) { (f), (s), (2 * (h) - 1), (m), (n) } -+#define F(f, s, h, m, n) { (f), (s), (2 * (h) - 1), (m), (n), 0, NULL } -+ -+#define FM(_f, _confs) { .freq = (_f), .confs_num = ARRAY_SIZE(_confs), .confs = (_confs) } -+#define C(s, h, m, n) { (s), (2 * (h) - 1), (m), (n) } -+ -+struct freq_conf { -+ u8 src; -+ u8 pre_div; -+ u16 m; -+ u16 n; -+}; - - struct freq_tbl { - unsigned long freq; -@@ -15,6 +25,8 @@ struct freq_tbl { - u8 pre_div; - u16 m; - u16 n; -+ int confs_num; -+ const struct freq_conf *confs; - }; - - /** ---- a/drivers/clk/qcom/clk-rcg2.c -+++ b/drivers/clk/qcom/clk-rcg2.c -@@ -203,11 +203,60 @@ clk_rcg2_recalc_rate(struct clk_hw *hw, - return __clk_rcg2_recalc_rate(hw, parent_rate, cfg); - } - -+static void -+clk_rcg2_select_conf(struct clk_hw *hw, struct freq_tbl *f_tbl, -+ const struct freq_tbl *f, unsigned long req_rate) -+{ -+ unsigned long best_rate = 0, parent_rate, rate; -+ const struct freq_conf *conf, *best_conf; -+ struct clk_rcg2 *rcg = to_clk_rcg2(hw); -+ struct clk_hw *p; -+ int index, i; -+ -+ /* Search in each provided config the one that is near the wanted rate */ -+ for (i = 0, conf = f->confs; i < f->confs_num; i++, conf++) { -+ index = qcom_find_src_index(hw, rcg->parent_map, conf->src); -+ if (index < 0) -+ continue; -+ -+ p = clk_hw_get_parent_by_index(hw, index); -+ if (!p) -+ continue; -+ -+ parent_rate = clk_hw_get_rate(p); -+ rate = calc_rate(parent_rate, conf->n, conf->m, conf->n, conf->pre_div); -+ -+ if (rate == req_rate) { -+ best_conf = conf; -+ break; -+ } -+ -+ if (abs(req_rate - rate) < abs(best_rate - rate)) { -+ best_rate = rate; -+ best_conf = conf; -+ } -+ } -+ -+ /* -+ * Very unlikely. -+ * Force the first conf if we can't find a correct config. -+ */ -+ if (unlikely(i == f->confs_num)) -+ best_conf = f->confs; -+ -+ /* Apply the config */ -+ f_tbl->src = best_conf->src; -+ f_tbl->pre_div = best_conf->pre_div; -+ f_tbl->m = best_conf->m; -+ f_tbl->n = best_conf->n; -+} -+ - static int _freq_tbl_determine_rate(struct clk_hw *hw, const struct freq_tbl *f, - struct clk_rate_request *req, - enum freq_policy policy) - { - unsigned long clk_flags, rate = req->rate; -+ struct freq_tbl f_tbl; - struct clk_hw *p; - struct clk_rcg2 *rcg = to_clk_rcg2(hw); - int index; -@@ -226,7 +275,15 @@ static int _freq_tbl_determine_rate(stru - if (!f) - return -EINVAL; - -- index = qcom_find_src_index(hw, rcg->parent_map, f->src); -+ f_tbl = *f; -+ /* -+ * A single freq may be reached by multiple configuration. -+ * Try to find the bast one if we have this kind of freq_table. -+ */ -+ if (f->confs) -+ clk_rcg2_select_conf(hw, &f_tbl, f, rate); -+ -+ index = qcom_find_src_index(hw, rcg->parent_map, f_tbl.src); - if (index < 0) - return index; - -@@ -236,18 +293,18 @@ static int _freq_tbl_determine_rate(stru - return -EINVAL; - - if (clk_flags & CLK_SET_RATE_PARENT) { -- rate = f->freq; -- if (f->pre_div) { -+ rate = f_tbl.freq; -+ if (f_tbl.pre_div) { - if (!rate) - rate = req->rate; - rate /= 2; -- rate *= f->pre_div + 1; -+ rate *= f_tbl.pre_div + 1; - } - -- if (f->n) { -+ if (f_tbl.n) { - u64 tmp = rate; -- tmp = tmp * f->n; -- do_div(tmp, f->m); -+ tmp = tmp * f_tbl.n; -+ do_div(tmp, f_tbl.m); - rate = tmp; - } - } else { -@@ -255,7 +312,7 @@ static int _freq_tbl_determine_rate(stru - } - req->best_parent_hw = p; - req->best_parent_rate = rate; -- req->rate = f->freq; -+ req->rate = f_tbl.freq; - - return 0; - } -@@ -351,6 +408,7 @@ static int __clk_rcg2_set_rate(struct cl - { - struct clk_rcg2 *rcg = to_clk_rcg2(hw); - const struct freq_tbl *f; -+ struct freq_tbl f_tbl; - - switch (policy) { - case FLOOR: -@@ -366,7 +424,15 @@ static int __clk_rcg2_set_rate(struct cl - if (!f) - return -EINVAL; - -- return clk_rcg2_configure(rcg, f); -+ f_tbl = *f; -+ /* -+ * A single freq may be reached by multiple configuration. -+ * Try to find the best one if we have this kind of freq_table. -+ */ -+ if (f->confs) -+ clk_rcg2_select_conf(hw, &f_tbl, f, rate); -+ -+ return clk_rcg2_configure(rcg, &f_tbl); - } - - static int clk_rcg2_set_rate(struct clk_hw *hw, unsigned long rate, diff --git a/target/linux/qualcommax/patches-6.1/0101-clk-qcom-gcc-ipq8074-rework-nss_port5-6-clock-to-mul.patch b/target/linux/qualcommax/patches-6.1/0101-clk-qcom-gcc-ipq8074-rework-nss_port5-6-clock-to-mul.patch deleted file mode 100644 index 62a30bbb22..0000000000 --- a/target/linux/qualcommax/patches-6.1/0101-clk-qcom-gcc-ipq8074-rework-nss_port5-6-clock-to-mul.patch +++ /dev/null @@ -1,129 +0,0 @@ -From f778553f296792f4d1e8b3552603ad6116ea3eb3 Mon Sep 17 00:00:00 2001 -From: Christian Marangi -Date: Thu, 3 Nov 2022 14:49:44 +0100 -Subject: [PATCH] clk: qcom: gcc-ipq8074: rework nss_port5/6 clock to multiple - conf - -Rework nss_port5/6 to use the new multiple configuration implementation -and correctly fix the clocks for these port under some corner case. - -This is particularly relevant for device that have 2.5G or 10G port -connected to port5 or port 6 on ipq8074. As the parent are shared -across multiple port it may be required to select the correct -configuration to accomplish the desired clock. Without this patch such -port doesn't work in some specific ethernet speed as the clock will be -set to the wrong frequency as we just select the first configuration for -the related frequency instead of selecting the best one. - -Tested-by: Robert Marko # ipq8074 Qnap QHora-301W -Signed-off-by: Christian Marangi ---- - drivers/clk/qcom/gcc-ipq8074.c | 64 +++++++++++++++++++++++++--------- - 1 file changed, 48 insertions(+), 16 deletions(-) - ---- a/drivers/clk/qcom/gcc-ipq8074.c -+++ b/drivers/clk/qcom/gcc-ipq8074.c -@@ -1676,13 +1676,21 @@ static struct clk_regmap_div nss_port4_t - }, - }; - -+static const struct freq_conf ftbl_nss_port5_rx_clk_src_25[] = { -+ C(P_UNIPHY1_RX, 12.5, 0, 0), -+ C(P_UNIPHY0_RX, 5, 0, 0), -+}; -+ -+static const struct freq_conf ftbl_nss_port5_rx_clk_src_125[] = { -+ C(P_UNIPHY1_RX, 2.5, 0, 0), -+ C(P_UNIPHY0_RX, 1, 0, 0), -+}; -+ - static const struct freq_tbl ftbl_nss_port5_rx_clk_src[] = { - F(19200000, P_XO, 1, 0, 0), -- F(25000000, P_UNIPHY1_RX, 12.5, 0, 0), -- F(25000000, P_UNIPHY0_RX, 5, 0, 0), -+ FM(25000000, ftbl_nss_port5_rx_clk_src_25), - F(78125000, P_UNIPHY1_RX, 4, 0, 0), -- F(125000000, P_UNIPHY1_RX, 2.5, 0, 0), -- F(125000000, P_UNIPHY0_RX, 1, 0, 0), -+ FM(125000000, ftbl_nss_port5_rx_clk_src_125), - F(156250000, P_UNIPHY1_RX, 2, 0, 0), - F(312500000, P_UNIPHY1_RX, 1, 0, 0), - { } -@@ -1738,13 +1746,21 @@ static struct clk_regmap_div nss_port5_r - }, - }; - -+static struct freq_conf ftbl_nss_port5_tx_clk_src_25[] = { -+ C(P_UNIPHY1_TX, 12.5, 0, 0), -+ C(P_UNIPHY0_TX, 5, 0, 0), -+}; -+ -+static struct freq_conf ftbl_nss_port5_tx_clk_src_125[] = { -+ C(P_UNIPHY1_TX, 2.5, 0, 0), -+ C(P_UNIPHY0_TX, 1, 0, 0), -+}; -+ - static const struct freq_tbl ftbl_nss_port5_tx_clk_src[] = { - F(19200000, P_XO, 1, 0, 0), -- F(25000000, P_UNIPHY1_TX, 12.5, 0, 0), -- F(25000000, P_UNIPHY0_TX, 5, 0, 0), -+ FM(25000000, ftbl_nss_port5_tx_clk_src_25), - F(78125000, P_UNIPHY1_TX, 4, 0, 0), -- F(125000000, P_UNIPHY1_TX, 2.5, 0, 0), -- F(125000000, P_UNIPHY0_TX, 1, 0, 0), -+ FM(125000000, ftbl_nss_port5_tx_clk_src_125), - F(156250000, P_UNIPHY1_TX, 2, 0, 0), - F(312500000, P_UNIPHY1_TX, 1, 0, 0), - { } -@@ -1800,13 +1816,21 @@ static struct clk_regmap_div nss_port5_t - }, - }; - -+static struct freq_conf ftbl_nss_port6_rx_clk_src_25[] = { -+ C(P_UNIPHY2_RX, 5, 0, 0), -+ C(P_UNIPHY2_RX, 12.5, 0, 0), -+}; -+ -+static struct freq_conf ftbl_nss_port6_rx_clk_src_125[] = { -+ C(P_UNIPHY2_RX, 1, 0, 0), -+ C(P_UNIPHY2_RX, 2.5, 0, 0), -+}; -+ - static const struct freq_tbl ftbl_nss_port6_rx_clk_src[] = { - F(19200000, P_XO, 1, 0, 0), -- F(25000000, P_UNIPHY2_RX, 5, 0, 0), -- F(25000000, P_UNIPHY2_RX, 12.5, 0, 0), -+ FM(25000000, ftbl_nss_port6_rx_clk_src_25), - F(78125000, P_UNIPHY2_RX, 4, 0, 0), -- F(125000000, P_UNIPHY2_RX, 1, 0, 0), -- F(125000000, P_UNIPHY2_RX, 2.5, 0, 0), -+ FM(125000000, ftbl_nss_port6_rx_clk_src_125), - F(156250000, P_UNIPHY2_RX, 2, 0, 0), - F(312500000, P_UNIPHY2_RX, 1, 0, 0), - { } -@@ -1857,13 +1881,21 @@ static struct clk_regmap_div nss_port6_r - }, - }; - -+static struct freq_conf ftbl_nss_port6_tx_clk_src_25[] = { -+ C(P_UNIPHY2_TX, 5, 0, 0), -+ C(P_UNIPHY2_TX, 12.5, 0, 0), -+}; -+ -+static struct freq_conf ftbl_nss_port6_tx_clk_src_125[] = { -+ C(P_UNIPHY2_TX, 1, 0, 0), -+ C(P_UNIPHY2_TX, 2.5, 0, 0), -+}; -+ - static const struct freq_tbl ftbl_nss_port6_tx_clk_src[] = { - F(19200000, P_XO, 1, 0, 0), -- F(25000000, P_UNIPHY2_TX, 5, 0, 0), -- F(25000000, P_UNIPHY2_TX, 12.5, 0, 0), -+ FM(25000000, ftbl_nss_port6_tx_clk_src_25), - F(78125000, P_UNIPHY2_TX, 4, 0, 0), -- F(125000000, P_UNIPHY2_TX, 1, 0, 0), -- F(125000000, P_UNIPHY2_TX, 2.5, 0, 0), -+ FM(125000000, ftbl_nss_port6_tx_clk_src_125), - F(156250000, P_UNIPHY2_TX, 2, 0, 0), - F(312500000, P_UNIPHY2_TX, 1, 0, 0), - { } diff --git a/target/linux/qualcommax/patches-6.1/0102-arm64-dts-ipq8074-add-reserved-memory-nodes.patch b/target/linux/qualcommax/patches-6.1/0102-arm64-dts-ipq8074-add-reserved-memory-nodes.patch deleted file mode 100644 index 3996d15d9d..0000000000 --- a/target/linux/qualcommax/patches-6.1/0102-arm64-dts-ipq8074-add-reserved-memory-nodes.patch +++ /dev/null @@ -1,60 +0,0 @@ -From ad2d07f71739351eeea1d8a120c0918e2c4b265f Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Wed, 22 Dec 2021 12:23:34 +0100 -Subject: [PATCH] arm64: dts: ipq8074: add reserved memory nodes - -IPQ8074 has multiple reserved memory ranges, if they are not defined -then weird things tend to happen, board hangs and resets when PCI or -WLAN is used etc. - -So, to avoid all of that add the reserved memory nodes from the downstream -5.4 kernel from QCA. -This is their default layout meant for devices with 1GB of RAM, but -devices with lower ammounts can override the Q6 node. - -Signed-off-by: Robert Marko ---- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 35 +++++++++++++++++++++++++++ - 1 file changed, 35 insertions(+) - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -85,6 +85,16 @@ - #size-cells = <2>; - ranges; - -+ nss@40000000 { -+ no-map; -+ reg = <0x0 0x40000000 0x0 0x01000000>; -+ }; -+ -+ tzapp_region: tzapp@4a400000 { -+ no-map; -+ reg = <0x0 0x4a400000 0x0 0x00200000>; -+ }; -+ - bootloader@4a600000 { - reg = <0x0 0x4a600000 0x0 0x400000>; - no-map; -@@ -107,6 +117,21 @@ - reg = <0x0 0x4ac00000 0x0 0x400000>; - no-map; - }; -+ -+ q6_region: wcnss@4b000000 { -+ no-map; -+ reg = <0x0 0x4b000000 0x0 0x05f00000>; -+ }; -+ -+ q6_etr_region: q6_etr_dump@50f00000 { -+ no-map; -+ reg = <0x0 0x50f00000 0x0 0x00100000>; -+ }; -+ -+ m3_dump_region: m3_dump@51000000 { -+ no-map; -+ reg = <0x0 0x51000000 0x0 0x100000>; -+ }; - }; - - firmware { diff --git a/target/linux/qualcommax/patches-6.1/0110-arm64-dts-qcom-ipq8074-pass-QMP-PCI-PHY-PIPE-clocks-.patch b/target/linux/qualcommax/patches-6.1/0110-arm64-dts-qcom-ipq8074-pass-QMP-PCI-PHY-PIPE-clocks-.patch deleted file mode 100644 index fd97663513..0000000000 --- a/target/linux/qualcommax/patches-6.1/0110-arm64-dts-qcom-ipq8074-pass-QMP-PCI-PHY-PIPE-clocks-.patch +++ /dev/null @@ -1,30 +0,0 @@ -From 8a576b5bc9f0555d1d970cacabcaa24a3b74fa57 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Wed, 16 Nov 2022 22:15:01 +0100 -Subject: [PATCH] arm64: dts: qcom: ipq8074: pass QMP PCI PHY PIPE clocks to - GCC - -Pass QMP PCI PHY PIPE clocks to the GCC controller so it does not have to -find them by matching globaly by name. - -If not passed directly, driver maintains backwards compatibility by then -falling back to global lookup. - -Signed-off-by: Robert Marko ---- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 4 ++-- - 1 file changed, 2 insertions(+), 2 deletions(-) - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -399,8 +399,8 @@ - gcc: gcc@1800000 { - compatible = "qcom,gcc-ipq8074"; - reg = <0x01800000 0x80000>; -- clocks = <&xo>, <&sleep_clk>; -- clock-names = "xo", "sleep_clk"; -+ clocks = <&xo>, <&sleep_clk>, <&pcie_phy0>, <&pcie_phy1>; -+ clock-names = "xo", "sleep_clk", "pcie0_pipe", "pcie1_pipe"; - #clock-cells = <1>; - #power-domain-cells = <1>; - #reset-cells = <1>; diff --git a/target/linux/qualcommax/patches-6.1/0111-arm64-dts-qcom-ipq8074-use-msi-parent-for-PCIe.patch b/target/linux/qualcommax/patches-6.1/0111-arm64-dts-qcom-ipq8074-use-msi-parent-for-PCIe.patch deleted file mode 100644 index 9163cd76fe..0000000000 --- a/target/linux/qualcommax/patches-6.1/0111-arm64-dts-qcom-ipq8074-use-msi-parent-for-PCIe.patch +++ /dev/null @@ -1,43 +0,0 @@ -From fb1f6850be00d8dd8a54017be4c1336e224069ac Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Wed, 16 Nov 2022 22:26:25 +0100 -Subject: [PATCH] arm64: dts: qcom: ipq8074: use msi-parent for PCIe - -Instead of hardcoding the IRQ, simply use msi-parent instead. - -Signed-off-by: Robert Marko ---- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 8 +++----- - 1 file changed, 3 insertions(+), 5 deletions(-) - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -734,7 +734,7 @@ - reg = <0x0b000000 0x1000>, <0x0b002000 0x1000>; - ranges = <0 0xb00a000 0xffd>; - -- v2m@0 { -+ gic_v2m0: v2m@0 { - compatible = "arm,gic-v2m-frame"; - msi-controller; - reg = <0x0 0xffd>; -@@ -847,8 +847,7 @@ - ranges = <0x81000000 0x0 0x00000000 0x10200000 0x0 0x10000>, /* I/O */ - <0x82000000 0x0 0x10220000 0x10220000 0x0 0xfde0000>; /* MEM */ - -- interrupts = ; -- interrupt-names = "msi"; -+ msi-parent = <&gic_v2m0>; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0x7>; - interrupt-map = <0 0 0 1 &intc 0 142 -@@ -909,8 +908,7 @@ - ranges = <0x81000000 0x0 0x00000000 0x20200000 0x0 0x10000>, /* I/O */ - <0x82000000 0x0 0x20220000 0x20220000 0x0 0xfde0000>; /* MEM */ - -- interrupts = ; -- interrupt-names = "msi"; -+ msi-parent = <&gic_v2m0>; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0x7>; - interrupt-map = <0 0 0 1 &intc 0 75 diff --git a/target/linux/qualcommax/patches-6.1/0112-remoteproc-qcom-Add-PRNG-proxy-clock.patch b/target/linux/qualcommax/patches-6.1/0112-remoteproc-qcom-Add-PRNG-proxy-clock.patch deleted file mode 100644 index 0a984948b5..0000000000 --- a/target/linux/qualcommax/patches-6.1/0112-remoteproc-qcom-Add-PRNG-proxy-clock.patch +++ /dev/null @@ -1,155 +0,0 @@ -From 125681433c8e526356947acf572fe8ca8ad32291 Mon Sep 17 00:00:00 2001 -From: Gokul Sriram Palanisamy -Date: Sat, 30 Jan 2021 10:50:05 +0530 -Subject: [PATCH] remoteproc: qcom: Add PRNG proxy clock - -PRNG clock is needed by the secure PIL, support for the same -is added in subsequent patches. - -Signed-off-by: Gokul Sriram Palanisamy -Signed-off-by: Sricharan R -Signed-off-by: Nikhil Prakash V ---- - drivers/remoteproc/qcom_q6v5_wcss.c | 65 +++++++++++++++++++++-------- - 1 file changed, 47 insertions(+), 18 deletions(-) - ---- a/drivers/remoteproc/qcom_q6v5_wcss.c -+++ b/drivers/remoteproc/qcom_q6v5_wcss.c -@@ -91,19 +91,6 @@ enum { - WCSS_QCS404, - }; - --struct wcss_data { -- const char *firmware_name; -- unsigned int crash_reason_smem; -- u32 version; -- bool aon_reset_required; -- bool wcss_q6_reset_required; -- const char *ssr_name; -- const char *sysmon_name; -- int ssctl_id; -- const struct rproc_ops *ops; -- bool requires_force_stop; --}; -- - struct q6v5_wcss { - struct device *dev; - -@@ -128,6 +115,7 @@ struct q6v5_wcss { - struct clk *qdsp6ss_xo_cbcr; - struct clk *qdsp6ss_core_gfmux; - struct clk *lcc_bcr_sleep; -+ struct clk *prng_clk; - struct regulator *cx_supply; - struct qcom_sysmon *sysmon; - -@@ -151,6 +139,21 @@ struct q6v5_wcss { - struct qcom_rproc_ssr ssr_subdev; - }; - -+struct wcss_data { -+ int (*init_clock)(struct q6v5_wcss *wcss); -+ int (*init_regulator)(struct q6v5_wcss *wcss); -+ const char *firmware_name; -+ unsigned int crash_reason_smem; -+ u32 version; -+ bool aon_reset_required; -+ bool wcss_q6_reset_required; -+ const char *ssr_name; -+ const char *sysmon_name; -+ int ssctl_id; -+ const struct rproc_ops *ops; -+ bool requires_force_stop; -+}; -+ - static int q6v5_wcss_reset(struct q6v5_wcss *wcss) - { - int ret; -@@ -240,6 +243,12 @@ static int q6v5_wcss_start(struct rproc - struct q6v5_wcss *wcss = rproc->priv; - int ret; - -+ ret = clk_prepare_enable(wcss->prng_clk); -+ if (ret) { -+ dev_err(wcss->dev, "prng clock enable failed\n"); -+ return ret; -+ } -+ - qcom_q6v5_prepare(&wcss->q6v5); - - /* Release Q6 and WCSS reset */ -@@ -733,6 +742,7 @@ static int q6v5_wcss_stop(struct rproc * - return ret; - } - -+ clk_disable_unprepare(wcss->prng_clk); - qcom_q6v5_unprepare(&wcss->q6v5); - - return 0; -@@ -900,7 +910,21 @@ static int q6v5_alloc_memory_region(stru - return 0; - } - --static int q6v5_wcss_init_clock(struct q6v5_wcss *wcss) -+static int ipq8074_init_clock(struct q6v5_wcss *wcss) -+{ -+ int ret; -+ -+ wcss->prng_clk = devm_clk_get(wcss->dev, "prng"); -+ if (IS_ERR(wcss->prng_clk)) { -+ ret = PTR_ERR(wcss->prng_clk); -+ if (ret != -EPROBE_DEFER) -+ dev_err(wcss->dev, "Failed to get prng clock\n"); -+ return ret; -+ } -+ return 0; -+} -+ -+static int qcs404_init_clock(struct q6v5_wcss *wcss) - { - int ret; - -@@ -990,7 +1014,7 @@ static int q6v5_wcss_init_clock(struct q - return 0; - } - --static int q6v5_wcss_init_regulator(struct q6v5_wcss *wcss) -+static int qcs404_init_regulator(struct q6v5_wcss *wcss) - { - wcss->cx_supply = devm_regulator_get(wcss->dev, "cx"); - if (IS_ERR(wcss->cx_supply)) -@@ -1034,12 +1058,14 @@ static int q6v5_wcss_probe(struct platfo - if (ret) - goto free_rproc; - -- if (wcss->version == WCSS_QCS404) { -- ret = q6v5_wcss_init_clock(wcss); -+ if (desc->init_clock) { -+ ret = desc->init_clock(wcss); - if (ret) - goto free_rproc; -+ } - -- ret = q6v5_wcss_init_regulator(wcss); -+ if (desc->init_regulator) { -+ ret = desc->init_regulator(wcss); - if (ret) - goto free_rproc; - } -@@ -1087,6 +1113,7 @@ static int q6v5_wcss_remove(struct platf - } - - static const struct wcss_data wcss_ipq8074_res_init = { -+ .init_clock = ipq8074_init_clock, - .firmware_name = "IPQ8074/q6_fw.mdt", - .crash_reason_smem = WCSS_CRASH_REASON, - .aon_reset_required = true, -@@ -1096,6 +1123,8 @@ static const struct wcss_data wcss_ipq80 - }; - - static const struct wcss_data wcss_qcs404_res_init = { -+ .init_clock = qcs404_init_clock, -+ .init_regulator = qcs404_init_regulator, - .crash_reason_smem = WCSS_CRASH_REASON, - .firmware_name = "wcnss.mdt", - .version = WCSS_QCS404, diff --git a/target/linux/qualcommax/patches-6.1/0113-remoteproc-qcom-Add-secure-PIL-support.patch b/target/linux/qualcommax/patches-6.1/0113-remoteproc-qcom-Add-secure-PIL-support.patch deleted file mode 100644 index 0328efc041..0000000000 --- a/target/linux/qualcommax/patches-6.1/0113-remoteproc-qcom-Add-secure-PIL-support.patch +++ /dev/null @@ -1,143 +0,0 @@ -From 7358d42dfbdfdb5d4f1d0d4c2e5c2bb4143a29b0 Mon Sep 17 00:00:00 2001 -From: Gokul Sriram Palanisamy -Date: Sat, 30 Jan 2021 10:50:06 +0530 -Subject: [PATCH] remoteproc: qcom: Add secure PIL support - -IPQ8074 uses secure PIL. Hence, adding the support for the same. - -Signed-off-by: Gokul Sriram Palanisamy -Signed-off-by: Sricharan R -Signed-off-by: Nikhil Prakash V ---- - drivers/remoteproc/qcom_q6v5_wcss.c | 43 +++++++++++++++++++++++++++-- - 1 file changed, 40 insertions(+), 3 deletions(-) - ---- a/drivers/remoteproc/qcom_q6v5_wcss.c -+++ b/drivers/remoteproc/qcom_q6v5_wcss.c -@@ -18,6 +18,7 @@ - #include - #include - #include -+#include - #include "qcom_common.h" - #include "qcom_pil_info.h" - #include "qcom_q6v5.h" -@@ -86,6 +87,9 @@ - #define TCSR_WCSS_CLK_ENABLE 0x14 - - #define MAX_HALT_REG 3 -+ -+#define WCNSS_PAS_ID 6 -+ - enum { - WCSS_IPQ8074, - WCSS_QCS404, -@@ -134,6 +138,7 @@ struct q6v5_wcss { - unsigned int crash_reason_smem; - u32 version; - bool requires_force_stop; -+ bool need_mem_protection; - - struct qcom_rproc_glink glink_subdev; - struct qcom_rproc_ssr ssr_subdev; -@@ -152,6 +157,7 @@ struct wcss_data { - int ssctl_id; - const struct rproc_ops *ops; - bool requires_force_stop; -+ bool need_mem_protection; - }; - - static int q6v5_wcss_reset(struct q6v5_wcss *wcss) -@@ -251,6 +257,15 @@ static int q6v5_wcss_start(struct rproc - - qcom_q6v5_prepare(&wcss->q6v5); - -+ if (wcss->need_mem_protection) { -+ ret = qcom_scm_pas_auth_and_reset(WCNSS_PAS_ID); -+ if (ret) { -+ dev_err(wcss->dev, "wcss_reset failed\n"); -+ return ret; -+ } -+ goto wait_for_reset; -+ } -+ - /* Release Q6 and WCSS reset */ - ret = reset_control_deassert(wcss->wcss_reset); - if (ret) { -@@ -285,6 +300,7 @@ static int q6v5_wcss_start(struct rproc - if (ret) - goto wcss_q6_reset; - -+wait_for_reset: - ret = qcom_q6v5_wait_for_start(&wcss->q6v5, 5 * HZ); - if (ret == -ETIMEDOUT) - dev_err(wcss->dev, "start timed out\n"); -@@ -718,6 +734,15 @@ static int q6v5_wcss_stop(struct rproc * - struct q6v5_wcss *wcss = rproc->priv; - int ret; - -+ if (wcss->need_mem_protection) { -+ ret = qcom_scm_pas_shutdown(WCNSS_PAS_ID); -+ if (ret) { -+ dev_err(wcss->dev, "not able to shutdown\n"); -+ return ret; -+ } -+ goto pas_done; -+ } -+ - /* WCSS powerdown */ - if (wcss->requires_force_stop) { - ret = qcom_q6v5_request_stop(&wcss->q6v5, NULL); -@@ -742,6 +767,7 @@ static int q6v5_wcss_stop(struct rproc * - return ret; - } - -+pas_done: - clk_disable_unprepare(wcss->prng_clk); - qcom_q6v5_unprepare(&wcss->q6v5); - -@@ -765,9 +791,15 @@ static int q6v5_wcss_load(struct rproc * - struct q6v5_wcss *wcss = rproc->priv; - int ret; - -- ret = qcom_mdt_load_no_init(wcss->dev, fw, rproc->firmware, -- 0, wcss->mem_region, wcss->mem_phys, -- wcss->mem_size, &wcss->mem_reloc); -+ if (wcss->need_mem_protection) -+ ret = qcom_mdt_load(wcss->dev, fw, rproc->firmware, -+ WCNSS_PAS_ID, wcss->mem_region, -+ wcss->mem_phys, wcss->mem_size, -+ &wcss->mem_reloc); -+ else -+ ret = qcom_mdt_load_no_init(wcss->dev, fw, rproc->firmware, -+ 0, wcss->mem_region, wcss->mem_phys, -+ wcss->mem_size, &wcss->mem_reloc); - if (ret) - return ret; - -@@ -1036,6 +1068,9 @@ static int q6v5_wcss_probe(struct platfo - if (!desc) - return -EINVAL; - -+ if (desc->need_mem_protection && !qcom_scm_is_available()) -+ return -EPROBE_DEFER; -+ - rproc = rproc_alloc(&pdev->dev, pdev->name, desc->ops, - desc->firmware_name, sizeof(*wcss)); - if (!rproc) { -@@ -1049,6 +1084,7 @@ static int q6v5_wcss_probe(struct platfo - - wcss->version = desc->version; - wcss->requires_force_stop = desc->requires_force_stop; -+ wcss->need_mem_protection = desc->need_mem_protection; - - ret = q6v5_wcss_init_mmio(wcss, pdev); - if (ret) -@@ -1120,6 +1156,7 @@ static const struct wcss_data wcss_ipq80 - .wcss_q6_reset_required = true, - .ops = &q6v5_wcss_ipq8074_ops, - .requires_force_stop = true, -+ .need_mem_protection = true, - }; - - static const struct wcss_data wcss_qcs404_res_init = { diff --git a/target/linux/qualcommax/patches-6.1/0114-remoteproc-qcom-Add-support-for-split-q6-m3-wlan-fir.patch b/target/linux/qualcommax/patches-6.1/0114-remoteproc-qcom-Add-support-for-split-q6-m3-wlan-fir.patch deleted file mode 100644 index e5c9506c89..0000000000 --- a/target/linux/qualcommax/patches-6.1/0114-remoteproc-qcom-Add-support-for-split-q6-m3-wlan-fir.patch +++ /dev/null @@ -1,103 +0,0 @@ -From b422c9d4f048b086ce83f44a7cfcddcce162897f Mon Sep 17 00:00:00 2001 -From: Gokul Sriram Palanisamy -Date: Sat, 30 Jan 2021 10:50:07 +0530 -Subject: [PATCH] remoteproc: qcom: Add support for split q6 + m3 wlan firmware - -IPQ8074 supports split firmware for q6 and m3 as well. -So add support for loading the m3 firmware before q6. -Now the drivers works fine for both split and unified -firmwares. - -Signed-off-by: Gokul Sriram Palanisamy -Signed-off-by: Sricharan R -Signed-off-by: Nikhil Prakash V ---- - drivers/remoteproc/qcom_q6v5_wcss.c | 33 +++++++++++++++++++++++++---- - 1 file changed, 29 insertions(+), 4 deletions(-) - ---- a/drivers/remoteproc/qcom_q6v5_wcss.c -+++ b/drivers/remoteproc/qcom_q6v5_wcss.c -@@ -139,6 +139,7 @@ struct q6v5_wcss { - u32 version; - bool requires_force_stop; - bool need_mem_protection; -+ const char *m3_firmware_name; - - struct qcom_rproc_glink glink_subdev; - struct qcom_rproc_ssr ssr_subdev; -@@ -147,7 +148,8 @@ struct q6v5_wcss { - struct wcss_data { - int (*init_clock)(struct q6v5_wcss *wcss); - int (*init_regulator)(struct q6v5_wcss *wcss); -- const char *firmware_name; -+ const char *q6_firmware_name; -+ const char *m3_firmware_name; - unsigned int crash_reason_smem; - u32 version; - bool aon_reset_required; -@@ -789,8 +791,29 @@ static void *q6v5_wcss_da_to_va(struct r - static int q6v5_wcss_load(struct rproc *rproc, const struct firmware *fw) - { - struct q6v5_wcss *wcss = rproc->priv; -+ const struct firmware *m3_fw; - int ret; - -+ if (wcss->m3_firmware_name) { -+ ret = request_firmware(&m3_fw, wcss->m3_firmware_name, -+ wcss->dev); -+ if (ret) -+ goto skip_m3; -+ -+ ret = qcom_mdt_load_no_init(wcss->dev, m3_fw, -+ wcss->m3_firmware_name, 0, -+ wcss->mem_region, wcss->mem_phys, -+ wcss->mem_size, &wcss->mem_reloc); -+ -+ release_firmware(m3_fw); -+ -+ if (ret) { -+ dev_err(wcss->dev, "can't load m3_fw.bXX\n"); -+ return ret; -+ } -+ } -+ -+skip_m3: - if (wcss->need_mem_protection) - ret = qcom_mdt_load(wcss->dev, fw, rproc->firmware, - WCNSS_PAS_ID, wcss->mem_region, -@@ -1072,7 +1095,7 @@ static int q6v5_wcss_probe(struct platfo - return -EPROBE_DEFER; - - rproc = rproc_alloc(&pdev->dev, pdev->name, desc->ops, -- desc->firmware_name, sizeof(*wcss)); -+ desc->q6_firmware_name, sizeof(*wcss)); - if (!rproc) { - dev_err(&pdev->dev, "failed to allocate rproc\n"); - return -ENOMEM; -@@ -1085,6 +1108,7 @@ static int q6v5_wcss_probe(struct platfo - wcss->version = desc->version; - wcss->requires_force_stop = desc->requires_force_stop; - wcss->need_mem_protection = desc->need_mem_protection; -+ wcss->m3_firmware_name = desc->m3_firmware_name; - - ret = q6v5_wcss_init_mmio(wcss, pdev); - if (ret) -@@ -1150,7 +1174,8 @@ static int q6v5_wcss_remove(struct platf - - static const struct wcss_data wcss_ipq8074_res_init = { - .init_clock = ipq8074_init_clock, -- .firmware_name = "IPQ8074/q6_fw.mdt", -+ .q6_firmware_name = "IPQ8074/q6_fw.mdt", -+ .m3_firmware_name = "IPQ8074/m3_fw.mdt", - .crash_reason_smem = WCSS_CRASH_REASON, - .aon_reset_required = true, - .wcss_q6_reset_required = true, -@@ -1163,7 +1188,7 @@ static const struct wcss_data wcss_qcs40 - .init_clock = qcs404_init_clock, - .init_regulator = qcs404_init_regulator, - .crash_reason_smem = WCSS_CRASH_REASON, -- .firmware_name = "wcnss.mdt", -+ .q6_firmware_name = "wcnss.mdt", - .version = WCSS_QCS404, - .aon_reset_required = false, - .wcss_q6_reset_required = false, diff --git a/target/linux/qualcommax/patches-6.1/0115-remoteproc-qcom-Add-ssr-subdevice-identifier.patch b/target/linux/qualcommax/patches-6.1/0115-remoteproc-qcom-Add-ssr-subdevice-identifier.patch deleted file mode 100644 index be63d46e8e..0000000000 --- a/target/linux/qualcommax/patches-6.1/0115-remoteproc-qcom-Add-ssr-subdevice-identifier.patch +++ /dev/null @@ -1,24 +0,0 @@ -From 3a8f67b4770c817b04794c9a02e3f88f85d86280 Mon Sep 17 00:00:00 2001 -From: Gokul Sriram Palanisamy -Date: Sat, 30 Jan 2021 10:50:08 +0530 -Subject: [PATCH] remoteproc: qcom: Add ssr subdevice identifier - -Add name for ssr subdevice on IPQ8074 SoC. - -Signed-off-by: Gokul Sriram Palanisamy -Signed-off-by: Sricharan R -Signed-off-by: Nikhil Prakash V ---- - drivers/remoteproc/qcom_q6v5_wcss.c | 1 + - 1 file changed, 1 insertion(+) - ---- a/drivers/remoteproc/qcom_q6v5_wcss.c -+++ b/drivers/remoteproc/qcom_q6v5_wcss.c -@@ -1179,6 +1179,7 @@ static const struct wcss_data wcss_ipq80 - .crash_reason_smem = WCSS_CRASH_REASON, - .aon_reset_required = true, - .wcss_q6_reset_required = true, -+ .ssr_name = "q6wcss", - .ops = &q6v5_wcss_ipq8074_ops, - .requires_force_stop = true, - .need_mem_protection = true, diff --git a/target/linux/qualcommax/patches-6.1/0116-remoteproc-qcom-Update-regmap-offsets-for-halt-regis.patch b/target/linux/qualcommax/patches-6.1/0116-remoteproc-qcom-Update-regmap-offsets-for-halt-regis.patch deleted file mode 100644 index f0b717210f..0000000000 --- a/target/linux/qualcommax/patches-6.1/0116-remoteproc-qcom-Update-regmap-offsets-for-halt-regis.patch +++ /dev/null @@ -1,79 +0,0 @@ -From 8c73af6e8d78c66cfef0f551b00d375ec0b67ff3 Mon Sep 17 00:00:00 2001 -From: Gokul Sriram Palanisamy -Date: Sat, 30 Jan 2021 10:50:09 +0530 -Subject: [PATCH] remoteproc: qcom: Update regmap offsets for halt register - -Fixed issue in reading halt-regs parameter from device-tree. - -Signed-off-by: Gokul Sriram Palanisamy -Signed-off-by: Sricharan R ---- - drivers/remoteproc/qcom_q6v5_wcss.c | 22 ++++++++++++++-------- - 1 file changed, 14 insertions(+), 8 deletions(-) - ---- a/drivers/remoteproc/qcom_q6v5_wcss.c -+++ b/drivers/remoteproc/qcom_q6v5_wcss.c -@@ -86,7 +86,7 @@ - #define TCSR_WCSS_CLK_MASK 0x1F - #define TCSR_WCSS_CLK_ENABLE 0x14 - --#define MAX_HALT_REG 3 -+#define MAX_HALT_REG 4 - - #define WCNSS_PAS_ID 6 - -@@ -154,6 +154,7 @@ struct wcss_data { - u32 version; - bool aon_reset_required; - bool wcss_q6_reset_required; -+ bool bcr_reset_required; - const char *ssr_name; - const char *sysmon_name; - int ssctl_id; -@@ -875,10 +876,13 @@ static int q6v5_wcss_init_reset(struct q - } - } - -- wcss->wcss_q6_bcr_reset = devm_reset_control_get_exclusive(dev, "wcss_q6_bcr_reset"); -- if (IS_ERR(wcss->wcss_q6_bcr_reset)) { -- dev_err(wcss->dev, "unable to acquire wcss_q6_bcr_reset\n"); -- return PTR_ERR(wcss->wcss_q6_bcr_reset); -+ if (desc->bcr_reset_required) { -+ wcss->wcss_q6_bcr_reset = devm_reset_control_get_exclusive(dev, -+ "wcss_q6_bcr_reset"); -+ if (IS_ERR(wcss->wcss_q6_bcr_reset)) { -+ dev_err(wcss->dev, "unable to acquire wcss_q6_bcr_reset\n"); -+ return PTR_ERR(wcss->wcss_q6_bcr_reset); -+ } - } - - return 0; -@@ -929,9 +933,9 @@ static int q6v5_wcss_init_mmio(struct q6 - return -EINVAL; - } - -- wcss->halt_q6 = halt_reg[0]; -- wcss->halt_wcss = halt_reg[1]; -- wcss->halt_nc = halt_reg[2]; -+ wcss->halt_q6 = halt_reg[1]; -+ wcss->halt_wcss = halt_reg[2]; -+ wcss->halt_nc = halt_reg[3]; - - return 0; - } -@@ -1179,6 +1183,7 @@ static const struct wcss_data wcss_ipq80 - .crash_reason_smem = WCSS_CRASH_REASON, - .aon_reset_required = true, - .wcss_q6_reset_required = true, -+ .bcr_reset_required = false, - .ssr_name = "q6wcss", - .ops = &q6v5_wcss_ipq8074_ops, - .requires_force_stop = true, -@@ -1193,6 +1198,7 @@ static const struct wcss_data wcss_qcs40 - .version = WCSS_QCS404, - .aon_reset_required = false, - .wcss_q6_reset_required = false, -+ .bcr_reset_required = true, - .ssr_name = "mpss", - .sysmon_name = "wcnss", - .ssctl_id = 0x12, diff --git a/target/linux/qualcommax/patches-6.1/0117-dt-bindings-clock-qcom-Add-reset-for-WCSSAON.patch b/target/linux/qualcommax/patches-6.1/0117-dt-bindings-clock-qcom-Add-reset-for-WCSSAON.patch deleted file mode 100644 index fe0e0f9e0b..0000000000 --- a/target/linux/qualcommax/patches-6.1/0117-dt-bindings-clock-qcom-Add-reset-for-WCSSAON.patch +++ /dev/null @@ -1,26 +0,0 @@ -From ff7c6533ed8c4de58ed6c8aab03ea59c03eb4f31 Mon Sep 17 00:00:00 2001 -From: Gokul Sriram Palanisamy -Date: Sat, 30 Jan 2021 10:50:10 +0530 -Subject: [PATCH] dt-bindings: clock: qcom: Add reset for WCSSAON - -Add binding for WCSSAON reset required for Q6v5 reset on IPQ8074 SoC. - -Signed-off-by: Gokul Sriram Palanisamy -Signed-off-by: Sricharan R -Signed-off-by: Nikhil Prakash V -Acked-by: Rob Herring -Acked-by: Stephen Boyd ---- - include/dt-bindings/clock/qcom,gcc-ipq8074.h | 1 + - 1 file changed, 1 insertion(+) - ---- a/include/dt-bindings/clock/qcom,gcc-ipq8074.h -+++ b/include/dt-bindings/clock/qcom,gcc-ipq8074.h -@@ -381,6 +381,7 @@ - #define GCC_NSSPORT4_RESET 143 - #define GCC_NSSPORT5_RESET 144 - #define GCC_NSSPORT6_RESET 145 -+#define GCC_WCSSAON_RESET 146 - - #define USB0_GDSC 0 - #define USB1_GDSC 1 diff --git a/target/linux/qualcommax/patches-6.1/0118-clk-qcom-Add-WCSSAON-reset.patch b/target/linux/qualcommax/patches-6.1/0118-clk-qcom-Add-WCSSAON-reset.patch deleted file mode 100644 index be0524338d..0000000000 --- a/target/linux/qualcommax/patches-6.1/0118-clk-qcom-Add-WCSSAON-reset.patch +++ /dev/null @@ -1,25 +0,0 @@ -From 43d9788f546d24df22d8ba3fcc2497d7ccc198f3 Mon Sep 17 00:00:00 2001 -From: Gokul Sriram Palanisamy -Date: Sat, 30 Jan 2021 10:50:11 +0530 -Subject: [PATCH] clk: qcom: Add WCSSAON reset - -Add WCSSAON reset required for Q6v5 on IPQ8074 SoC. - -Signed-off-by: Gokul Sriram Palanisamy -Signed-off-by: Sricharan R -Signed-off-by: Nikhil Prakash V -Acked-by: Stephen Boyd ---- - drivers/clk/qcom/gcc-ipq8074.c | 1 + - 1 file changed, 1 insertion(+) - ---- a/drivers/clk/qcom/gcc-ipq8074.c -+++ b/drivers/clk/qcom/gcc-ipq8074.c -@@ -4711,6 +4711,7 @@ static const struct qcom_reset_map gcc_i - [GCC_NSSPORT4_RESET] = { .reg = 0x68014, .bitmask = BIT(27) | GENMASK(9, 8) }, - [GCC_NSSPORT5_RESET] = { .reg = 0x68014, .bitmask = BIT(28) | GENMASK(11, 10) }, - [GCC_NSSPORT6_RESET] = { .reg = 0x68014, .bitmask = BIT(29) | GENMASK(13, 12) }, -+ [GCC_WCSSAON_RESET] = { 0x59010, 0 }, - }; - - static struct gdsc *gcc_ipq8074_gdscs[] = { diff --git a/target/linux/qualcommax/patches-6.1/0119-remoteproc-wcss-disable-auto-boot-for-IPQ8074.patch b/target/linux/qualcommax/patches-6.1/0119-remoteproc-wcss-disable-auto-boot-for-IPQ8074.patch deleted file mode 100644 index 8674522a11..0000000000 --- a/target/linux/qualcommax/patches-6.1/0119-remoteproc-wcss-disable-auto-boot-for-IPQ8074.patch +++ /dev/null @@ -1,48 +0,0 @@ -From 406a332fd1bcc4e18d73cce390f56272fe9111d7 Mon Sep 17 00:00:00 2001 -From: Sivaprakash Murugesan -Date: Fri, 17 Apr 2020 16:37:10 +0530 -Subject: [PATCH] remoteproc: wcss: disable auto boot for IPQ8074 - -There is no need for remoteproc to boot automatically, ath11k will trigger -booting when its probing. - -Signed-off-by: Sivaprakash Murugesan -Signed-off-by: Robert Marko ---- - drivers/remoteproc/qcom_q6v5_wcss.c | 4 ++++ - 1 file changed, 4 insertions(+) - ---- a/drivers/remoteproc/qcom_q6v5_wcss.c -+++ b/drivers/remoteproc/qcom_q6v5_wcss.c -@@ -161,6 +161,7 @@ struct wcss_data { - const struct rproc_ops *ops; - bool requires_force_stop; - bool need_mem_protection; -+ bool need_auto_boot; - }; - - static int q6v5_wcss_reset(struct q6v5_wcss *wcss) -@@ -1150,6 +1151,7 @@ static int q6v5_wcss_probe(struct platfo - desc->sysmon_name, - desc->ssctl_id); - -+ rproc->auto_boot = desc->need_auto_boot; - ret = rproc_add(rproc); - if (ret) - goto free_rproc; -@@ -1188,6 +1190,7 @@ static const struct wcss_data wcss_ipq80 - .ops = &q6v5_wcss_ipq8074_ops, - .requires_force_stop = true, - .need_mem_protection = true, -+ .need_auto_boot = false, - }; - - static const struct wcss_data wcss_qcs404_res_init = { -@@ -1204,6 +1207,7 @@ static const struct wcss_data wcss_qcs40 - .ssctl_id = 0x12, - .ops = &q6v5_wcss_qcs404_ops, - .requires_force_stop = false, -+ .need_auto_boot = true, - }; - - static const struct of_device_id q6v5_wcss_of_match[] = { diff --git a/target/linux/qualcommax/patches-6.1/0120-arm64-dts-qcom-Enable-Q6v5-WCSS-for-ipq8074-SoC.patch b/target/linux/qualcommax/patches-6.1/0120-arm64-dts-qcom-Enable-Q6v5-WCSS-for-ipq8074-SoC.patch deleted file mode 100644 index 17ecd069a6..0000000000 --- a/target/linux/qualcommax/patches-6.1/0120-arm64-dts-qcom-Enable-Q6v5-WCSS-for-ipq8074-SoC.patch +++ /dev/null @@ -1,120 +0,0 @@ -From 7388400b8bd42f71d040dbf2fdbdcb834fcc0ede Mon Sep 17 00:00:00 2001 -From: Gokul Sriram Palanisamy -Date: Sat, 30 Jan 2021 10:50:13 +0530 -Subject: [PATCH] arm64: dts: qcom: Enable Q6v5 WCSS for ipq8074 SoC - -Enable remoteproc WCSS PIL driver with glink and ssr subdevices. -Also enables smp2p and mailboxes required for IPC. - -Signed-off-by: Gokul Sriram Palanisamy -Signed-off-by: Sricharan R -Signed-off-by: Nikhil Prakash V -Signed-off-by: Robert Marko ---- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 81 +++++++++++++++++++++++++++ - 1 file changed, 81 insertions(+) - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -141,6 +141,32 @@ - }; - }; - -+ wcss: smp2p-wcss { -+ compatible = "qcom,smp2p"; -+ qcom,smem = <435>, <428>; -+ -+ interrupt-parent = <&intc>; -+ interrupts = <0 322 1>; -+ -+ mboxes = <&apcs_glb 9>; -+ -+ qcom,local-pid = <0>; -+ qcom,remote-pid = <1>; -+ -+ wcss_smp2p_out: master-kernel { -+ qcom,entry-name = "master-kernel"; -+ qcom,smp2p-feature-ssr-ack; -+ #qcom,smem-state-cells = <1>; -+ }; -+ -+ wcss_smp2p_in: slave-kernel { -+ qcom,entry-name = "slave-kernel"; -+ -+ interrupt-controller; -+ #interrupt-cells = <2>; -+ }; -+ }; -+ - soc: soc { - #address-cells = <0x1>; - #size-cells = <0x1>; -@@ -417,6 +443,11 @@ - reg = <0x01937000 0x21000>; - }; - -+ tcsr_q6: syscon@1945000 { -+ compatible = "syscon"; -+ reg = <0x01945000 0xe000>; -+ }; -+ - spmi_bus: spmi@200f000 { - compatible = "qcom,spmi-pmic-arb"; - reg = <0x0200f000 0x001000>, -@@ -949,6 +980,56 @@ - "axi_s_sticky"; - status = "disabled"; - }; -+ -+ q6v5_wcss: q6v5_wcss@cd00000 { -+ compatible = "qcom,ipq8074-wcss-pil"; -+ reg = <0x0cd00000 0x4040>, -+ <0x004ab000 0x20>; -+ reg-names = "qdsp6", -+ "rmb"; -+ qca,auto-restart; -+ qca,extended-intc; -+ interrupts-extended = <&intc 0 325 1>, -+ <&wcss_smp2p_in 0 0>, -+ <&wcss_smp2p_in 1 0>, -+ <&wcss_smp2p_in 2 0>, -+ <&wcss_smp2p_in 3 0>; -+ interrupt-names = "wdog", -+ "fatal", -+ "ready", -+ "handover", -+ "stop-ack"; -+ -+ resets = <&gcc GCC_WCSSAON_RESET>, -+ <&gcc GCC_WCSS_BCR>, -+ <&gcc GCC_WCSS_Q6_BCR>; -+ -+ reset-names = "wcss_aon_reset", -+ "wcss_reset", -+ "wcss_q6_reset"; -+ -+ clocks = <&gcc GCC_PRNG_AHB_CLK>; -+ clock-names = "prng"; -+ -+ qcom,halt-regs = <&tcsr_q6 0xa000 0xd000 0x0>; -+ -+ qcom,smem-states = <&wcss_smp2p_out 0>, -+ <&wcss_smp2p_out 1>; -+ qcom,smem-state-names = "shutdown", -+ "stop"; -+ -+ memory-region = <&q6_region>; -+ -+ glink-edge { -+ interrupts = ; -+ qcom,remote-pid = <1>; -+ mboxes = <&apcs_glb 8>; -+ -+ rpm_requests { -+ qcom,glink-channels = "IPCRTR"; -+ }; -+ }; -+ }; - }; - - timer { diff --git a/target/linux/qualcommax/patches-6.1/0121-arm64-dts-ipq8074-Add-WLAN-node.patch b/target/linux/qualcommax/patches-6.1/0121-arm64-dts-ipq8074-Add-WLAN-node.patch deleted file mode 100644 index 76d3f35dd2..0000000000 --- a/target/linux/qualcommax/patches-6.1/0121-arm64-dts-ipq8074-Add-WLAN-node.patch +++ /dev/null @@ -1,135 +0,0 @@ -From a67d1901741c162645eda0dbdc3a2c0c2aff5cf4 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Tue, 21 Dec 2021 14:49:36 +0100 -Subject: [PATCH] arm64: dts: ipq8074: Add WLAN node - -IPQ8074 has a AHB based Q6v5 802.11ax radios that are supported -by the ath11k. - -Add the required DT node to enable the built-in radios. - -Signed-off-by: Robert Marko ---- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 111 ++++++++++++++++++++++++++ - 1 file changed, 111 insertions(+) - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -1030,6 +1030,117 @@ - }; - }; - }; -+ -+ wifi: wifi@c0000000 { -+ compatible = "qcom,ipq8074-wifi"; -+ reg = <0xc000000 0x2000000>; -+ -+ interrupts = , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ ; -+ -+ interrupt-names = "misc-pulse1", -+ "misc-latch", -+ "sw-exception", -+ "ce0", -+ "ce1", -+ "ce2", -+ "ce3", -+ "ce4", -+ "ce5", -+ "ce6", -+ "ce7", -+ "ce8", -+ "ce9", -+ "ce10", -+ "ce11", -+ "host2wbm-desc-feed", -+ "host2reo-re-injection", -+ "host2reo-command", -+ "host2rxdma-monitor-ring3", -+ "host2rxdma-monitor-ring2", -+ "host2rxdma-monitor-ring1", -+ "reo2ost-exception", -+ "wbm2host-rx-release", -+ "reo2host-status", -+ "reo2host-destination-ring4", -+ "reo2host-destination-ring3", -+ "reo2host-destination-ring2", -+ "reo2host-destination-ring1", -+ "rxdma2host-monitor-destination-mac3", -+ "rxdma2host-monitor-destination-mac2", -+ "rxdma2host-monitor-destination-mac1", -+ "ppdu-end-interrupts-mac3", -+ "ppdu-end-interrupts-mac2", -+ "ppdu-end-interrupts-mac1", -+ "rxdma2host-monitor-status-ring-mac3", -+ "rxdma2host-monitor-status-ring-mac2", -+ "rxdma2host-monitor-status-ring-mac1", -+ "host2rxdma-host-buf-ring-mac3", -+ "host2rxdma-host-buf-ring-mac2", -+ "host2rxdma-host-buf-ring-mac1", -+ "rxdma2host-destination-ring-mac3", -+ "rxdma2host-destination-ring-mac2", -+ "rxdma2host-destination-ring-mac1", -+ "host2tcl-input-ring4", -+ "host2tcl-input-ring3", -+ "host2tcl-input-ring2", -+ "host2tcl-input-ring1", -+ "wbm2host-tx-completions-ring3", -+ "wbm2host-tx-completions-ring2", -+ "wbm2host-tx-completions-ring1", -+ "tcl2host-status-ring"; -+ qcom,rproc = <&q6v5_wcss>; -+ status = "disabled"; -+ }; - }; - - timer { diff --git a/target/linux/qualcommax/patches-6.1/0122-arm64-dts-ipq8074-add-CPU-clock.patch b/target/linux/qualcommax/patches-6.1/0122-arm64-dts-ipq8074-add-CPU-clock.patch deleted file mode 100644 index a3c5f344ab..0000000000 --- a/target/linux/qualcommax/patches-6.1/0122-arm64-dts-ipq8074-add-CPU-clock.patch +++ /dev/null @@ -1,59 +0,0 @@ -From cb3ef99c1553565e1dc0301ccd5c1c0fa2d15c15 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Fri, 31 Dec 2021 17:56:14 +0100 -Subject: [PATCH] arm64: dts: ipq8074: add CPU clock - -Now that CPU clock is exposed and can be controlled, add the necessary -properties to the CPU nodes. - -Signed-off-by: Robert Marko ---- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 9 +++++++++ - 1 file changed, 9 insertions(+) - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -5,6 +5,7 @@ - - #include - #include -+#include - - / { - #address-cells = <2>; -@@ -38,6 +39,8 @@ - reg = <0x0>; - next-level-cache = <&L2_0>; - enable-method = "psci"; -+ clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>; -+ clock-names = "cpu"; - }; - - CPU1: cpu@1 { -@@ -46,6 +49,8 @@ - enable-method = "psci"; - reg = <0x1>; - next-level-cache = <&L2_0>; -+ clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>; -+ clock-names = "cpu"; - }; - - CPU2: cpu@2 { -@@ -54,6 +59,8 @@ - enable-method = "psci"; - reg = <0x2>; - next-level-cache = <&L2_0>; -+ clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>; -+ clock-names = "cpu"; - }; - - CPU3: cpu@3 { -@@ -62,6 +69,8 @@ - enable-method = "psci"; - reg = <0x3>; - next-level-cache = <&L2_0>; -+ clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>; -+ clock-names = "cpu"; - }; - - L2_0: l2-cache { diff --git a/target/linux/qualcommax/patches-6.1/0123-arm64-dts-ipq8074-add-cooling-cells-to-CPU-nodes.patch b/target/linux/qualcommax/patches-6.1/0123-arm64-dts-ipq8074-add-cooling-cells-to-CPU-nodes.patch deleted file mode 100644 index 3520b38134..0000000000 --- a/target/linux/qualcommax/patches-6.1/0123-arm64-dts-ipq8074-add-cooling-cells-to-CPU-nodes.patch +++ /dev/null @@ -1,48 +0,0 @@ -From 347ca56e86c99021fad059b9a8ef101245b8507e Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Fri, 31 Dec 2021 20:38:06 +0100 -Subject: [PATCH] arm64: dts: ipq8074: add cooling cells to CPU nodes - -Since there is CPU Freq support as well as thermal sensor support -now for the IPQ8074, add cooling cells to CPU nodes so that they can -be used as cooling devices using CPU Freq. - -Signed-off-by: Robert Marko ---- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 4 ++++ - 1 file changed, 4 insertions(+) - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -41,6 +41,7 @@ - enable-method = "psci"; - clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>; - clock-names = "cpu"; -+ #cooling-cells = <2>; - }; - - CPU1: cpu@1 { -@@ -51,6 +52,7 @@ - next-level-cache = <&L2_0>; - clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>; - clock-names = "cpu"; -+ #cooling-cells = <2>; - }; - - CPU2: cpu@2 { -@@ -61,6 +63,7 @@ - next-level-cache = <&L2_0>; - clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>; - clock-names = "cpu"; -+ #cooling-cells = <2>; - }; - - CPU3: cpu@3 { -@@ -71,6 +74,7 @@ - next-level-cache = <&L2_0>; - clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>; - clock-names = "cpu"; -+ #cooling-cells = <2>; - }; - - L2_0: l2-cache { diff --git a/target/linux/qualcommax/patches-6.1/0129-arm64-dts-qcom-ipq8074-add-QFPROM-fuses.patch b/target/linux/qualcommax/patches-6.1/0129-arm64-dts-qcom-ipq8074-add-QFPROM-fuses.patch deleted file mode 100644 index 8ec4660123..0000000000 --- a/target/linux/qualcommax/patches-6.1/0129-arm64-dts-qcom-ipq8074-add-QFPROM-fuses.patch +++ /dev/null @@ -1,128 +0,0 @@ -From 04d2fc6a551bbd972a6428059b45ce79cb9de9d7 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Fri, 6 May 2022 22:38:24 +0200 -Subject: [PATCH] arm64: dts: qcom: ipq8074: add QFPROM fuses - -Add the QFPROM node and CPR fuses. - -Signed-off-by: Robert Marko ---- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 107 ++++++++++++++++++++++++++ - 1 file changed, 107 insertions(+) - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -343,6 +343,113 @@ - status = "disabled"; - }; - -+ qfprom: efuse@a4000 { -+ compatible = "qcom,ipq8074-qfprom", "qcom,qfprom"; -+ reg = <0x000a4000 0x1000>; -+ #address-cells = <1>; -+ #size-cells = <1>; -+ -+ cpr_efuse_speedbin: speedbin@125 { -+ reg = <0x125 0x1>; -+ bits = <0 3>; -+ }; -+ -+ cpr_efuse_boost_cfg: boost_cfg@125 { -+ reg = <0x125 0x1>; -+ bits = <3 3>; -+ }; -+ -+ cpr_efuse_misc_volt_adj: misc_volt_adj@125 { -+ reg = <0x125 0x1>; -+ bits = <3 3>; -+ }; -+ -+ cpr_efuse_boost_volt: boost_volt@126 { -+ reg = <0x126 0x1>; -+ bits = <6 1>; -+ }; -+ -+ cpr_efuse_revision: revision@23e { -+ reg = <0x23e 0x1>; -+ bits = <5 3>; -+ }; -+ -+ cpr_efuse_ro_sel0: rosel0@249 { -+ reg = <0x249 0x1>; -+ bits = <0 4>; -+ }; -+ -+ cpr_efuse_ro_sel1: rosel1@248 { -+ reg = <0x248 0x1>; -+ bits = <4 4>; -+ }; -+ -+ cpr_efuse_ro_sel2: rosel2@248 { -+ reg = <0x248 0x2>; -+ bits = <0 4>; -+ }; -+ -+ cpr_efuse_ro_sel3: rosel3@249 { -+ reg = <0x249 0x1>; -+ bits = <4 4>; -+ }; -+ -+ cpr_efuse_init_voltage0: ivoltage0@23a { -+ reg = <0x23a 0x1>; -+ bits = <2 6>; -+ }; -+ -+ cpr_efuse_init_voltage1: ivoltage1@239 { -+ reg = <0x239 0x2>; -+ bits = <4 6>; -+ }; -+ -+ cpr_efuse_init_voltage2: ivoltage2@238 { -+ reg = <0x238 0x2>; -+ bits = <6 6>; -+ }; -+ -+ cpr_efuse_init_voltage3: ivoltage3@238 { -+ reg = <0x238 0x1>; -+ bits = <0 6>; -+ }; -+ -+ cpr_efuse_quot0: quot0@244 { -+ reg = <0x244 0x2>; -+ bits = <0 12>; -+ }; -+ -+ cpr_efuse_quot1: quot1@242 { -+ reg = <0x242 0x2>; -+ bits = <4 12>; -+ }; -+ -+ cpr_efuse_quot2: quot2@241 { -+ reg = <0x241 0x2>; -+ bits = <0 12>; -+ }; -+ -+ cpr_efuse_quot3: quot3@245 { -+ reg = <0x245 0x2>; -+ bits = <4 12>; -+ }; -+ -+ cpr_efuse_quot0_offset: quot0_offset@23d { -+ reg = <0x23d 0x2>; -+ bits = <6 7>; -+ }; -+ -+ cpr_efuse_quot1_offset: quot1_offset@23c { -+ reg = <0x23c 0x2>; -+ bits = <7 7>; -+ }; -+ -+ cpr_efuse_quot2_offset: quot2_offset@23c { -+ reg = <0x23c 0x1>; -+ bits = <0 7>; -+ }; -+ }; -+ - prng: rng@e3000 { - compatible = "qcom,prng-ee"; - reg = <0x000e3000 0x1000>; diff --git a/target/linux/qualcommax/patches-6.1/0130-arm64-dts-qcom-ipq8074-add-CPU-OPP-table.patch b/target/linux/qualcommax/patches-6.1/0130-arm64-dts-qcom-ipq8074-add-CPU-OPP-table.patch deleted file mode 100644 index 9c1e7b9d29..0000000000 --- a/target/linux/qualcommax/patches-6.1/0130-arm64-dts-qcom-ipq8074-add-CPU-OPP-table.patch +++ /dev/null @@ -1,102 +0,0 @@ -From a20c4e8738a00087aa5d53fe5148ed484e23d229 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Sat, 31 Dec 2022 13:56:26 +0100 -Subject: [PATCH] arm64: dts: qcom: ipq8074: add CPU OPP table - -Now that there is NVMEM CPUFreq support for IPQ8074, we can add the OPP -table for SoC. - -Signed-off-by: Robert Marko ---- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 52 +++++++++++++++++++++++++++ - 1 file changed, 52 insertions(+) - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -42,6 +42,7 @@ - clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>; - clock-names = "cpu"; - #cooling-cells = <2>; -+ operating-points-v2 = <&cpu_opp_table>; - }; - - CPU1: cpu@1 { -@@ -53,6 +54,7 @@ - clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>; - clock-names = "cpu"; - #cooling-cells = <2>; -+ operating-points-v2 = <&cpu_opp_table>; - }; - - CPU2: cpu@2 { -@@ -64,6 +66,7 @@ - clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>; - clock-names = "cpu"; - #cooling-cells = <2>; -+ operating-points-v2 = <&cpu_opp_table>; - }; - - CPU3: cpu@3 { -@@ -75,6 +78,7 @@ - clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>; - clock-names = "cpu"; - #cooling-cells = <2>; -+ operating-points-v2 = <&cpu_opp_table>; - }; - - L2_0: l2-cache { -@@ -83,6 +87,54 @@ - }; - }; - -+ cpu_opp_table: opp-table { -+ compatible = "operating-points-v2-kryo-cpu"; -+ nvmem-cells = <&cpr_efuse_speedbin>; -+ opp-shared; -+ -+ opp-1017600000 { -+ opp-hz = /bits/ 64 <1017600000>; -+ opp-microvolt = <1>; -+ opp-supported-hw = <0xf>; -+ clock-latency-ns = <200000>; -+ }; -+ -+ opp-1382400000 { -+ opp-hz = /bits/ 64 <1382400000>; -+ opp-microvolt = <2>; -+ opp-supported-hw = <0xf>; -+ clock-latency-ns = <200000>; -+ }; -+ -+ opp-1651200000 { -+ opp-hz = /bits/ 64 <1651200000>; -+ opp-microvolt = <3>; -+ opp-supported-hw = <0x1>; -+ clock-latency-ns = <200000>; -+ }; -+ -+ opp-1843200000 { -+ opp-hz = /bits/ 64 <1843200000>; -+ opp-microvolt = <4>; -+ opp-supported-hw = <0x1>; -+ clock-latency-ns = <200000>; -+ }; -+ -+ opp-1920000000 { -+ opp-hz = /bits/ 64 <1920000000>; -+ opp-microvolt = <5>; -+ opp-supported-hw = <0x1>; -+ clock-latency-ns = <200000>; -+ }; -+ -+ opp-2208000000 { -+ opp-hz = /bits/ 64 <2208000000>; -+ opp-microvolt = <6>; -+ opp-supported-hw = <0x1>; -+ clock-latency-ns = <200000>; -+ }; -+ }; -+ - pmu { - compatible = "arm,cortex-a53-pmu"; - interrupts = ; diff --git a/target/linux/qualcommax/patches-6.1/0136-remoteproc-qcom-wcss-populate-driver-data-for-IPQ601.patch b/target/linux/qualcommax/patches-6.1/0136-remoteproc-qcom-wcss-populate-driver-data-for-IPQ601.patch deleted file mode 100644 index 9a5a3407e1..0000000000 --- a/target/linux/qualcommax/patches-6.1/0136-remoteproc-qcom-wcss-populate-driver-data-for-IPQ601.patch +++ /dev/null @@ -1,61 +0,0 @@ -From 9dd19a9ae36bc60d58287d0c52e53024d484e64d Mon Sep 17 00:00:00 2001 -From: Gokul Sriram Palanisamy -Date: Fri, 29 Jan 2021 22:41:59 +0530 -Subject: [PATCH 2/3] remoteproc: qcom: wcss: populate driver data for IPQ6018 - -Populate hardcoded param using driver data for IPQ6018 SoCs. - -Signed-off-by: Gokul Sriram Palanisamy ---- - drivers/remoteproc/qcom_q6v5_wcss.c | 19 +++++++++++++++++-- - 1 file changed, 17 insertions(+), 2 deletions(-) - ---- a/drivers/remoteproc/qcom_q6v5_wcss.c -+++ b/drivers/remoteproc/qcom_q6v5_wcss.c -@@ -970,7 +970,7 @@ static int q6v5_alloc_memory_region(stru - return 0; - } - --static int ipq8074_init_clock(struct q6v5_wcss *wcss) -+static int ipq_init_clock(struct q6v5_wcss *wcss) - { - int ret; - -@@ -1179,7 +1179,7 @@ static int q6v5_wcss_remove(struct platf - } - - static const struct wcss_data wcss_ipq8074_res_init = { -- .init_clock = ipq8074_init_clock, -+ .init_clock = ipq_init_clock, - .q6_firmware_name = "IPQ8074/q6_fw.mdt", - .m3_firmware_name = "IPQ8074/m3_fw.mdt", - .crash_reason_smem = WCSS_CRASH_REASON, -@@ -1193,6 +1193,20 @@ static const struct wcss_data wcss_ipq80 - .need_auto_boot = false, - }; - -+static const struct wcss_data wcss_ipq6018_res_init = { -+ .init_clock = ipq_init_clock, -+ .q6_firmware_name = "IPQ6018/q6_fw.mdt", -+ .m3_firmware_name = "IPQ6018/m3_fw.mdt", -+ .crash_reason_smem = WCSS_CRASH_REASON, -+ .aon_reset_required = true, -+ .wcss_q6_reset_required = true, -+ .bcr_reset_required = false, -+ .ssr_name = "q6wcss", -+ .ops = &q6v5_wcss_ipq8074_ops, -+ .requires_force_stop = true, -+ .need_mem_protection = true, -+}; -+ - static const struct wcss_data wcss_qcs404_res_init = { - .init_clock = qcs404_init_clock, - .init_regulator = qcs404_init_regulator, -@@ -1212,6 +1226,7 @@ static const struct wcss_data wcss_qcs40 - - static const struct of_device_id q6v5_wcss_of_match[] = { - { .compatible = "qcom,ipq8074-wcss-pil", .data = &wcss_ipq8074_res_init }, -+ { .compatible = "qcom,ipq6018-wcss-pil", .data = &wcss_ipq6018_res_init }, - { .compatible = "qcom,qcs404-wcss-pil", .data = &wcss_qcs404_res_init }, - { }, - }; diff --git a/target/linux/qualcommax/patches-6.1/0137-arm64-dts-qcom-ipq6018-add-SDHCI-node.patch b/target/linux/qualcommax/patches-6.1/0137-arm64-dts-qcom-ipq6018-add-SDHCI-node.patch deleted file mode 100644 index bfca74ba76..0000000000 --- a/target/linux/qualcommax/patches-6.1/0137-arm64-dts-qcom-ipq6018-add-SDHCI-node.patch +++ /dev/null @@ -1,45 +0,0 @@ -From e4d7544ce092807e8c5aeb618cec30e2eb9b40c2 Mon Sep 17 00:00:00 2001 -From: Mantas Pucka -Date: Mon, 24 Apr 2023 15:13:32 +0300 -Subject: [PATCH 3/3] arm64: dts: qcom: ipq6018: add SDHCI node - -IPQ6018 has one SD/eMMC controller, add node for it. - -Signed-off-by: Mantas Pucka -Tested-by: Robert Marko ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 23 +++++++++++++++++++++++ - 1 file changed, 23 insertions(+) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -469,6 +469,29 @@ - }; - }; - -+ sdhc_1: mmc@7804000 { -+ compatible = "qcom,ipq6018-sdhci", "qcom,sdhci-msm-v5"; -+ reg = <0x0 0x07804000 0x0 0x1000>, -+ <0x0 0x07805000 0x0 0x1000>, -+ <0x0 0x07808000 0x0 0x2000>; -+ reg-names = "hc", "cqhci", "ice"; -+ -+ interrupts = , -+ ; -+ interrupt-names = "hc_irq", "pwr_irq"; -+ -+ clocks = <&gcc GCC_SDCC1_AHB_CLK>, -+ <&gcc GCC_SDCC1_APPS_CLK>, -+ <&xo>, -+ <&gcc GCC_SDCC1_ICE_CORE_CLK>; -+ clock-names = "iface", "core", "xo", "ice"; -+ -+ resets = <&gcc GCC_SDCC1_BCR>; -+ supports-cqe; -+ bus-width = <8>; -+ status = "disabled"; -+ }; -+ - blsp_dma: dma-controller@7884000 { - compatible = "qcom,bam-v1.7.0"; - reg = <0x0 0x07884000 0x0 0x2b000>; diff --git a/target/linux/qualcommax/patches-6.1/0139-arm64-dts-qcom-ipq6018-add-LDOA2-regulator.patch b/target/linux/qualcommax/patches-6.1/0139-arm64-dts-qcom-ipq6018-add-LDOA2-regulator.patch deleted file mode 100644 index 8889db97f9..0000000000 --- a/target/linux/qualcommax/patches-6.1/0139-arm64-dts-qcom-ipq6018-add-LDOA2-regulator.patch +++ /dev/null @@ -1,27 +0,0 @@ -From d24bc08bfc66f47d6e0a294a080d62893a7696b5 Mon Sep 17 00:00:00 2001 -From: Chukun Pan -Date: Thu, 18 Jan 2024 21:30:21 +0800 -Subject: [PATCH] arm64: dts: qcom: ipq6018: add LDOA2 regulator - -Add LDOA2 regulator of MP5496 to support SDCC voltage scaling. - -Suggested-by: Robert Marko -Signed-off-by: Chukun Pan ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 5 +++++ - 1 file changed, 5 insertions(+) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -178,6 +178,11 @@ - regulator-max-microvolt = <1062500>; - regulator-always-on; - }; -+ -+ ipq6018_l2: l2 { -+ regulator-min-microvolt = <1800000>; -+ regulator-max-microvolt = <3300000>; -+ }; - }; - }; - }; diff --git a/target/linux/qualcommax/patches-6.1/0400-mtd-rawnand-add-support-for-TH58NYG3S0HBAI4.patch b/target/linux/qualcommax/patches-6.1/0400-mtd-rawnand-add-support-for-TH58NYG3S0HBAI4.patch deleted file mode 100644 index c52681928b..0000000000 --- a/target/linux/qualcommax/patches-6.1/0400-mtd-rawnand-add-support-for-TH58NYG3S0HBAI4.patch +++ /dev/null @@ -1,42 +0,0 @@ -From 8d8b37d3af2bdccf0a37d2017d876bfc6ce42552 Mon Sep 17 00:00:00 2001 -From: Chukun Pan -Date: Fri, 20 Oct 2023 23:18:21 +0800 -Subject: [PATCH 1/1] mtd: rawnand: add support for TH58NYG3S0HBAI4 NAND flash - -The Toshiba TH58NYG3S0HBAI4 is detected with 128 byte OOB while the flash -has 256 bytes OOB. Since it is not an ONFI compliant NAND, the model name -cannot be read from anywhere, add a static NAND ID entry to correct this. - -However, the NAND ID of this flash is inconsistent with the datasheet. -The actual NAND ID is only 4 ID bytes, the last ID byte is missing. - -Datasheet available at (the ID table is on page 50): -https://europe.kioxia.com/content/dam/kioxia/newidr/productinfo/datasheet/201910/DST_TH58NYG3S0HBAI4-TDE_EN_31565.pdf - -Datasheet NAND ID: {0x98, 0xa3, 0x91, 0x26, 0x76} -Actual NAND ID: {0x98, 0xa3, 0x91, 0x26} - -It seems that this flash may be counterfeit, but another Toshiba flash -also has the same problem. Maybe the driver has a bug, or some Toshiba -nand flash is like this. Anyway, add a static NAND ID entry with only -4 ID bytes as a hack to make sure it works. - -Tested on Arcadyan AW1000 flashed with OpenWrt. - -Signed-off-by: Chukun Pan ---- - drivers/mtd/nand/raw/nand_ids.c | 3 +++ - 1 file changed, 3 insertions(+) - ---- a/drivers/mtd/nand/raw/nand_ids.c -+++ b/drivers/mtd/nand/raw/nand_ids.c -@@ -55,6 +55,9 @@ struct nand_flash_dev nand_flash_ids[] = - { .id = {0xad, 0xde, 0x14, 0xa7, 0x42, 0x4a} }, - SZ_16K, SZ_8K, SZ_4M, NAND_NEED_SCRAMBLING, 6, 1664, - NAND_ECC_INFO(40, SZ_1K) }, -+ {"TH58NYG3S0HBAI4 8G 1.8V 8-bit", /* Last ID bytes missing */ -+ { .id = {0x98, 0xa3, 0x91, 0x26} }, -+ SZ_4K, SZ_1K, SZ_256K, 0, 4, 256, NAND_ECC_INFO(8, SZ_512) }, - {"TH58NVG2S3HBAI4 4G 3.3V 8-bit", - { .id = {0x98, 0xdc, 0x91, 0x15, 0x76} }, - SZ_2K, SZ_512, SZ_128K, 0, 5, 128, NAND_ECC_INFO(8, SZ_512) }, diff --git a/target/linux/qualcommax/patches-6.1/0900-power-Add-Qualcomm-APM.patch b/target/linux/qualcommax/patches-6.1/0900-power-Add-Qualcomm-APM.patch deleted file mode 100644 index 2e5c72b7d1..0000000000 --- a/target/linux/qualcommax/patches-6.1/0900-power-Add-Qualcomm-APM.patch +++ /dev/null @@ -1,1047 +0,0 @@ -From 6c98adf98236b8644b8f5e1aa7af9f1a88ea2766 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Mon, 11 Apr 2022 14:38:08 +0200 -Subject: [PATCH] power: Add Qualcomm APM - -Add Qualcomm APM driver, which allows scaling cache and memory fabrics. - -Signed-off-by: Robert Marko ---- - drivers/power/Kconfig | 1 + - drivers/power/Makefile | 1 + - drivers/power/qcom/Kconfig | 7 + - drivers/power/qcom/Makefile | 1 + - drivers/power/qcom/apm.c | 944 +++++++++++++++++++++++++++++++++ - include/linux/power/qcom/apm.h | 48 ++ - 6 files changed, 1002 insertions(+) - create mode 100644 drivers/power/qcom/Kconfig - create mode 100644 drivers/power/qcom/Makefile - create mode 100644 drivers/power/qcom/apm.c - create mode 100644 include/linux/power/qcom/apm.h - ---- a/drivers/power/Kconfig -+++ b/drivers/power/Kconfig -@@ -1,3 +1,4 @@ - # SPDX-License-Identifier: GPL-2.0-only - source "drivers/power/reset/Kconfig" - source "drivers/power/supply/Kconfig" -+source "drivers/power/qcom/Kconfig" ---- a/drivers/power/Makefile -+++ b/drivers/power/Makefile -@@ -1,3 +1,4 @@ - # SPDX-License-Identifier: GPL-2.0-only - obj-$(CONFIG_POWER_RESET) += reset/ - obj-$(CONFIG_POWER_SUPPLY) += supply/ -+obj-$(CONFIG_QCOM_APM) += qcom/ ---- /dev/null -+++ b/drivers/power/qcom/Kconfig -@@ -0,0 +1,7 @@ -+config QCOM_APM -+ bool "Qualcomm Technologies Inc platform specific APM driver" -+ help -+ Platform specific driver to manage the power source of -+ memory arrays. Interfaces with regulator drivers to ensure -+ SRAM Vmin requirements are met across different performance -+ levels. ---- /dev/null -+++ b/drivers/power/qcom/Makefile -@@ -0,0 +1 @@ -+obj-$(CONFIG_QCOM_APM) += apm.o ---- /dev/null -+++ b/drivers/power/qcom/apm.c -@@ -0,0 +1,944 @@ -+/* -+ * Copyright (c) 2015-2016, The Linux Foundation. All rights reserved. -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 and -+ * only version 2 as published by the Free Software Foundation. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ */ -+ -+#define pr_fmt(fmt) "%s: " fmt, __func__ -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+/* -+ * VDD_APCC -+ * ============================================================= -+ * | VDD_MX | | -+ * | ==========================|============= | -+ * ___|___ ___|___ ___|___ ___|___ ___|___ ___|___ -+ * | | | | | | | | | | | | -+ * | APCC | | MX HS | | MX HS | | APCC | | MX HS | | APCC | -+ * | HS | | | | | | HS | | | | HS | -+ * |_______| |_______| |_______| |_______| |_______| |_______| -+ * |_________| |_________| |__________| -+ * | | | -+ * ______|_____ ______|_____ _______|_____ -+ * | | | | | | -+ * | | | | | | -+ * | CPU MEM | | L2 MEM | | L3 MEM | -+ * | Arrays | | Arrays | | Arrays | -+ * | | | | | | -+ * |____________| |____________| |_____________| -+ * -+ */ -+ -+/* Register value definitions */ -+#define APCS_GFMUXA_SEL_VAL 0x13 -+#define APCS_GFMUXA_DESEL_VAL 0x03 -+#define MSM_APM_MX_MODE_VAL 0x00 -+#define MSM_APM_APCC_MODE_VAL 0x10 -+#define MSM_APM_MX_DONE_VAL 0x00 -+#define MSM_APM_APCC_DONE_VAL 0x03 -+#define MSM_APM_OVERRIDE_SEL_VAL 0xb0 -+#define MSM_APM_SEC_CLK_SEL_VAL 0x30 -+#define SPM_EVENT_SET_VAL 0x01 -+#define SPM_EVENT_CLEAR_VAL 0x00 -+ -+/* Register bit mask definitions */ -+#define MSM_APM_CTL_STS_MASK 0x0f -+ -+/* Register offset definitions */ -+#define APCC_APM_MODE 0x00000098 -+#define APCC_APM_CTL_STS 0x000000a8 -+#define APCS_SPARE 0x00000068 -+#define APCS_VERSION 0x00000fd0 -+ -+#define HMSS_VERSION_1P2 0x10020000 -+ -+#define MSM_APM_SWITCH_TIMEOUT_US 10 -+#define SPM_WAKEUP_DELAY_US 2 -+#define SPM_EVENT_NUM 6 -+ -+#define MSM_APM_DRIVER_NAME "qcom,msm-apm" -+ -+enum { -+ MSM8996_ID, -+ MSM8953_ID, -+ IPQ807x_ID, -+}; -+ -+struct msm_apm_ctrl_dev { -+ struct list_head list; -+ struct device *dev; -+ enum msm_apm_supply supply; -+ spinlock_t lock; -+ void __iomem *reg_base; -+ void __iomem *apcs_csr_base; -+ void __iomem **apcs_spm_events_addr; -+ void __iomem *apc0_pll_ctl_addr; -+ void __iomem *apc1_pll_ctl_addr; -+ u32 version; -+ struct dentry *debugfs; -+ u32 msm_id; -+}; -+ -+#if defined(CONFIG_DEBUG_FS) -+static struct dentry *apm_debugfs_base; -+#endif -+ -+static DEFINE_MUTEX(apm_ctrl_list_mutex); -+static LIST_HEAD(apm_ctrl_list); -+ -+/* -+ * Get the resources associated with the APM controller from device tree -+ * and remap all I/O addresses that are relevant to this HW revision. -+ */ -+static int msm_apm_ctrl_devm_ioremap(struct platform_device *pdev, -+ struct msm_apm_ctrl_dev *ctrl) -+{ -+ struct device *dev = &pdev->dev; -+ struct resource *res; -+ static const char *res_name[SPM_EVENT_NUM] = { -+ "apc0-l2-spm", -+ "apc1-l2-spm", -+ "apc0-cpu0-spm", -+ "apc0-cpu1-spm", -+ "apc1-cpu0-spm", -+ "apc1-cpu1-spm" -+ }; -+ int i, ret = 0; -+ -+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pm-apcc-glb"); -+ if (!res) { -+ dev_err(dev, "Missing PM APCC Global register physical address"); -+ return -EINVAL; -+ } -+ ctrl->reg_base = devm_ioremap(dev, res->start, resource_size(res)); -+ if (!ctrl->reg_base) { -+ dev_err(dev, "Failed to map PM APCC Global registers\n"); -+ return -ENOMEM; -+ } -+ -+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "apcs-csr"); -+ if (!res) { -+ dev_err(dev, "Missing APCS CSR physical base address"); -+ return -EINVAL; -+ } -+ ctrl->apcs_csr_base = devm_ioremap(dev, res->start, resource_size(res)); -+ if (!ctrl->apcs_csr_base) { -+ dev_err(dev, "Failed to map APCS CSR registers\n"); -+ return -ENOMEM; -+ } -+ -+ ctrl->version = readl_relaxed(ctrl->apcs_csr_base + APCS_VERSION); -+ -+ if (ctrl->version >= HMSS_VERSION_1P2) -+ return ret; -+ -+ ctrl->apcs_spm_events_addr = devm_kzalloc(&pdev->dev, -+ SPM_EVENT_NUM -+ * sizeof(void __iomem *), -+ GFP_KERNEL); -+ if (!ctrl->apcs_spm_events_addr) { -+ dev_err(dev, "Failed to allocate memory for APCS SPM event registers\n"); -+ return -ENOMEM; -+ } -+ -+ for (i = 0; i < SPM_EVENT_NUM; i++) { -+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, -+ res_name[i]); -+ if (!res) { -+ dev_err(dev, "Missing address for %s\n", res_name[i]); -+ ret = -EINVAL; -+ goto free_events; -+ } -+ -+ ctrl->apcs_spm_events_addr[i] = devm_ioremap(dev, res->start, -+ resource_size(res)); -+ if (!ctrl->apcs_spm_events_addr[i]) { -+ dev_err(dev, "Failed to map %s\n", res_name[i]); -+ ret = -ENOMEM; -+ goto free_events; -+ } -+ -+ dev_dbg(dev, "%s event phys: %pa virt:0x%p\n", res_name[i], -+ &res->start, ctrl->apcs_spm_events_addr[i]); -+ } -+ -+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, -+ "apc0-pll-ctl"); -+ if (!res) { -+ dev_err(dev, "Missing APC0 PLL CTL physical address\n"); -+ ret = -EINVAL; -+ goto free_events; -+ } -+ -+ ctrl->apc0_pll_ctl_addr = devm_ioremap(dev, -+ res->start, -+ resource_size(res)); -+ if (!ctrl->apc0_pll_ctl_addr) { -+ dev_err(dev, "Failed to map APC0 PLL CTL register\n"); -+ ret = -ENOMEM; -+ goto free_events; -+ } -+ -+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, -+ "apc1-pll-ctl"); -+ if (!res) { -+ dev_err(dev, "Missing APC1 PLL CTL physical address\n"); -+ ret = -EINVAL; -+ goto free_events; -+ } -+ -+ ctrl->apc1_pll_ctl_addr = devm_ioremap(dev, -+ res->start, -+ resource_size(res)); -+ if (!ctrl->apc1_pll_ctl_addr) { -+ dev_err(dev, "Failed to map APC1 PLL CTL register\n"); -+ ret = -ENOMEM; -+ goto free_events; -+ } -+ -+ return ret; -+ -+free_events: -+ devm_kfree(dev, ctrl->apcs_spm_events_addr); -+ return ret; -+} -+ -+/* 8953 register offset definition */ -+#define MSM8953_APM_DLY_CNTR 0x2ac -+ -+/* Register field shift definitions */ -+#define APM_CTL_SEL_SWITCH_DLY_SHIFT 0 -+#define APM_CTL_RESUME_CLK_DLY_SHIFT 8 -+#define APM_CTL_HALT_CLK_DLY_SHIFT 16 -+#define APM_CTL_POST_HALT_DLY_SHIFT 24 -+ -+/* Register field mask definitions */ -+#define APM_CTL_SEL_SWITCH_DLY_MASK GENMASK(7, 0) -+#define APM_CTL_RESUME_CLK_DLY_MASK GENMASK(15, 8) -+#define APM_CTL_HALT_CLK_DLY_MASK GENMASK(23, 16) -+#define APM_CTL_POST_HALT_DLY_MASK GENMASK(31, 24) -+ -+/* -+ * Get the resources associated with the msm8953 APM controller from -+ * device tree, remap all I/O addresses, and program the initial -+ * register configuration required for the 8953 APM controller device. -+ */ -+static int msm8953_apm_ctrl_init(struct platform_device *pdev, -+ struct msm_apm_ctrl_dev *ctrl) -+{ -+ struct device *dev = &pdev->dev; -+ struct resource *res; -+ u32 delay_counter, val = 0, regval = 0; -+ int rc = 0; -+ -+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pm-apcc-glb"); -+ if (!res) { -+ dev_err(dev, "Missing PM APCC Global register physical address\n"); -+ return -ENODEV; -+ } -+ ctrl->reg_base = devm_ioremap(dev, res->start, resource_size(res)); -+ if (!ctrl->reg_base) { -+ dev_err(dev, "Failed to map PM APCC Global registers\n"); -+ return -ENOMEM; -+ } -+ -+ /* -+ * Initial APM register configuration required before starting -+ * APM HW controller. -+ */ -+ regval = readl_relaxed(ctrl->reg_base + MSM8953_APM_DLY_CNTR); -+ val = regval; -+ -+ if (of_find_property(dev->of_node, "qcom,apm-post-halt-delay", NULL)) { -+ rc = of_property_read_u32(dev->of_node, -+ "qcom,apm-post-halt-delay", &delay_counter); -+ if (rc < 0) { -+ dev_err(dev, "apm-post-halt-delay read failed, rc = %d", -+ rc); -+ return rc; -+ } -+ -+ val &= ~APM_CTL_POST_HALT_DLY_MASK; -+ val |= (delay_counter << APM_CTL_POST_HALT_DLY_SHIFT) -+ & APM_CTL_POST_HALT_DLY_MASK; -+ } -+ -+ if (of_find_property(dev->of_node, "qcom,apm-halt-clk-delay", NULL)) { -+ rc = of_property_read_u32(dev->of_node, -+ "qcom,apm-halt-clk-delay", &delay_counter); -+ if (rc < 0) { -+ dev_err(dev, "apm-halt-clk-delay read failed, rc = %d", -+ rc); -+ return rc; -+ } -+ -+ val &= ~APM_CTL_HALT_CLK_DLY_MASK; -+ val |= (delay_counter << APM_CTL_HALT_CLK_DLY_SHIFT) -+ & APM_CTL_HALT_CLK_DLY_MASK; -+ } -+ -+ if (of_find_property(dev->of_node, "qcom,apm-resume-clk-delay", NULL)) { -+ rc = of_property_read_u32(dev->of_node, -+ "qcom,apm-resume-clk-delay", &delay_counter); -+ if (rc < 0) { -+ dev_err(dev, "apm-resume-clk-delay read failed, rc = %d", -+ rc); -+ return rc; -+ } -+ -+ val &= ~APM_CTL_RESUME_CLK_DLY_MASK; -+ val |= (delay_counter << APM_CTL_RESUME_CLK_DLY_SHIFT) -+ & APM_CTL_RESUME_CLK_DLY_MASK; -+ } -+ -+ if (of_find_property(dev->of_node, "qcom,apm-sel-switch-delay", NULL)) { -+ rc = of_property_read_u32(dev->of_node, -+ "qcom,apm-sel-switch-delay", &delay_counter); -+ if (rc < 0) { -+ dev_err(dev, "apm-sel-switch-delay read failed, rc = %d", -+ rc); -+ return rc; -+ } -+ -+ val &= ~APM_CTL_SEL_SWITCH_DLY_MASK; -+ val |= (delay_counter << APM_CTL_SEL_SWITCH_DLY_SHIFT) -+ & APM_CTL_SEL_SWITCH_DLY_MASK; -+ } -+ -+ if (val != regval) { -+ writel_relaxed(val, ctrl->reg_base + MSM8953_APM_DLY_CNTR); -+ /* make sure write completes before return */ -+ mb(); -+ } -+ -+ return rc; -+} -+ -+static int msm8996_apm_switch_to_mx(struct msm_apm_ctrl_dev *ctrl_dev) -+{ -+ int i, timeout = MSM_APM_SWITCH_TIMEOUT_US; -+ u32 regval; -+ int ret = 0; -+ unsigned long flags; -+ -+ spin_lock_irqsave(&ctrl_dev->lock, flags); -+ -+ /* Perform revision-specific programming steps */ -+ if (ctrl_dev->version < HMSS_VERSION_1P2) { -+ /* Clear SPM events */ -+ for (i = 0; i < SPM_EVENT_NUM; i++) -+ writel_relaxed(SPM_EVENT_CLEAR_VAL, -+ ctrl_dev->apcs_spm_events_addr[i]); -+ -+ udelay(SPM_WAKEUP_DELAY_US); -+ -+ /* Switch APC/CBF to GPLL0 clock */ -+ writel_relaxed(APCS_GFMUXA_SEL_VAL, -+ ctrl_dev->apcs_csr_base + APCS_SPARE); -+ ndelay(200); -+ writel_relaxed(MSM_APM_OVERRIDE_SEL_VAL, -+ ctrl_dev->apc0_pll_ctl_addr); -+ ndelay(200); -+ writel_relaxed(MSM_APM_OVERRIDE_SEL_VAL, -+ ctrl_dev->apc1_pll_ctl_addr); -+ -+ /* Ensure writes complete before proceeding */ -+ mb(); -+ } -+ -+ /* Switch arrays to MX supply and wait for its completion */ -+ writel_relaxed(MSM_APM_MX_MODE_VAL, ctrl_dev->reg_base + -+ APCC_APM_MODE); -+ -+ /* Ensure write above completes before delaying */ -+ mb(); -+ -+ while (timeout > 0) { -+ regval = readl_relaxed(ctrl_dev->reg_base + APCC_APM_CTL_STS); -+ if ((regval & MSM_APM_CTL_STS_MASK) == -+ MSM_APM_MX_DONE_VAL) -+ break; -+ -+ udelay(1); -+ timeout--; -+ } -+ -+ if (timeout == 0) { -+ ret = -ETIMEDOUT; -+ dev_err(ctrl_dev->dev, "APCC to MX APM switch timed out. APCC_APM_CTL_STS=0x%x\n", -+ regval); -+ } -+ -+ /* Perform revision-specific programming steps */ -+ if (ctrl_dev->version < HMSS_VERSION_1P2) { -+ /* Switch APC/CBF clocks to original source */ -+ writel_relaxed(APCS_GFMUXA_DESEL_VAL, -+ ctrl_dev->apcs_csr_base + APCS_SPARE); -+ ndelay(200); -+ writel_relaxed(MSM_APM_SEC_CLK_SEL_VAL, -+ ctrl_dev->apc0_pll_ctl_addr); -+ ndelay(200); -+ writel_relaxed(MSM_APM_SEC_CLK_SEL_VAL, -+ ctrl_dev->apc1_pll_ctl_addr); -+ -+ /* Complete clock source switch before SPM event sequence */ -+ mb(); -+ -+ /* Set SPM events */ -+ for (i = 0; i < SPM_EVENT_NUM; i++) -+ writel_relaxed(SPM_EVENT_SET_VAL, -+ ctrl_dev->apcs_spm_events_addr[i]); -+ } -+ -+ if (!ret) { -+ ctrl_dev->supply = MSM_APM_SUPPLY_MX; -+ dev_dbg(ctrl_dev->dev, "APM supply switched to MX\n"); -+ } -+ -+ spin_unlock_irqrestore(&ctrl_dev->lock, flags); -+ -+ return ret; -+} -+ -+static int msm8996_apm_switch_to_apcc(struct msm_apm_ctrl_dev *ctrl_dev) -+{ -+ int i, timeout = MSM_APM_SWITCH_TIMEOUT_US; -+ u32 regval; -+ int ret = 0; -+ unsigned long flags; -+ -+ spin_lock_irqsave(&ctrl_dev->lock, flags); -+ -+ /* Perform revision-specific programming steps */ -+ if (ctrl_dev->version < HMSS_VERSION_1P2) { -+ /* Clear SPM events */ -+ for (i = 0; i < SPM_EVENT_NUM; i++) -+ writel_relaxed(SPM_EVENT_CLEAR_VAL, -+ ctrl_dev->apcs_spm_events_addr[i]); -+ -+ udelay(SPM_WAKEUP_DELAY_US); -+ -+ /* Switch APC/CBF to GPLL0 clock */ -+ writel_relaxed(APCS_GFMUXA_SEL_VAL, -+ ctrl_dev->apcs_csr_base + APCS_SPARE); -+ ndelay(200); -+ writel_relaxed(MSM_APM_OVERRIDE_SEL_VAL, -+ ctrl_dev->apc0_pll_ctl_addr); -+ ndelay(200); -+ writel_relaxed(MSM_APM_OVERRIDE_SEL_VAL, -+ ctrl_dev->apc1_pll_ctl_addr); -+ -+ /* Ensure previous writes complete before proceeding */ -+ mb(); -+ } -+ -+ /* Switch arrays to APCC supply and wait for its completion */ -+ writel_relaxed(MSM_APM_APCC_MODE_VAL, ctrl_dev->reg_base + -+ APCC_APM_MODE); -+ -+ /* Ensure write above completes before delaying */ -+ mb(); -+ -+ while (timeout > 0) { -+ regval = readl_relaxed(ctrl_dev->reg_base + APCC_APM_CTL_STS); -+ if ((regval & MSM_APM_CTL_STS_MASK) == -+ MSM_APM_APCC_DONE_VAL) -+ break; -+ -+ udelay(1); -+ timeout--; -+ } -+ -+ if (timeout == 0) { -+ ret = -ETIMEDOUT; -+ dev_err(ctrl_dev->dev, "MX to APCC APM switch timed out. APCC_APM_CTL_STS=0x%x\n", -+ regval); -+ } -+ -+ /* Perform revision-specific programming steps */ -+ if (ctrl_dev->version < HMSS_VERSION_1P2) { -+ /* Set SPM events */ -+ for (i = 0; i < SPM_EVENT_NUM; i++) -+ writel_relaxed(SPM_EVENT_SET_VAL, -+ ctrl_dev->apcs_spm_events_addr[i]); -+ -+ /* Complete SPM event sequence before clock source switch */ -+ mb(); -+ -+ /* Switch APC/CBF clocks to original source */ -+ writel_relaxed(APCS_GFMUXA_DESEL_VAL, -+ ctrl_dev->apcs_csr_base + APCS_SPARE); -+ ndelay(200); -+ writel_relaxed(MSM_APM_SEC_CLK_SEL_VAL, -+ ctrl_dev->apc0_pll_ctl_addr); -+ ndelay(200); -+ writel_relaxed(MSM_APM_SEC_CLK_SEL_VAL, -+ ctrl_dev->apc1_pll_ctl_addr); -+ } -+ -+ if (!ret) { -+ ctrl_dev->supply = MSM_APM_SUPPLY_APCC; -+ dev_dbg(ctrl_dev->dev, "APM supply switched to APCC\n"); -+ } -+ -+ spin_unlock_irqrestore(&ctrl_dev->lock, flags); -+ -+ return ret; -+} -+ -+/* 8953 register value definitions */ -+#define MSM8953_APM_MX_MODE_VAL 0x00 -+#define MSM8953_APM_APCC_MODE_VAL 0x02 -+#define MSM8953_APM_MX_DONE_VAL 0x00 -+#define MSM8953_APM_APCC_DONE_VAL 0x03 -+ -+/* 8953 register offset definitions */ -+#define MSM8953_APCC_APM_MODE 0x000002a8 -+#define MSM8953_APCC_APM_CTL_STS 0x000002b0 -+ -+/* 8953 constants */ -+#define MSM8953_APM_SWITCH_TIMEOUT_US 500 -+ -+/* Register bit mask definitions */ -+#define MSM8953_APM_CTL_STS_MASK 0x1f -+ -+static int msm8953_apm_switch_to_mx(struct msm_apm_ctrl_dev *ctrl_dev) -+{ -+ int timeout = MSM8953_APM_SWITCH_TIMEOUT_US; -+ u32 regval; -+ int ret = 0; -+ unsigned long flags; -+ -+ spin_lock_irqsave(&ctrl_dev->lock, flags); -+ -+ /* Switch arrays to MX supply and wait for its completion */ -+ writel_relaxed(MSM8953_APM_MX_MODE_VAL, ctrl_dev->reg_base + -+ MSM8953_APCC_APM_MODE); -+ -+ /* Ensure write above completes before delaying */ -+ mb(); -+ -+ while (timeout > 0) { -+ regval = readl_relaxed(ctrl_dev->reg_base + -+ MSM8953_APCC_APM_CTL_STS); -+ if ((regval & MSM8953_APM_CTL_STS_MASK) == -+ MSM8953_APM_MX_DONE_VAL) -+ break; -+ -+ udelay(1); -+ timeout--; -+ } -+ -+ if (timeout == 0) { -+ ret = -ETIMEDOUT; -+ dev_err(ctrl_dev->dev, "APCC to MX APM switch timed out. APCC_APM_CTL_STS=0x%x\n", -+ regval); -+ } else { -+ ctrl_dev->supply = MSM_APM_SUPPLY_MX; -+ dev_dbg(ctrl_dev->dev, "APM supply switched to MX\n"); -+ } -+ -+ spin_unlock_irqrestore(&ctrl_dev->lock, flags); -+ -+ return ret; -+} -+ -+static int msm8953_apm_switch_to_apcc(struct msm_apm_ctrl_dev *ctrl_dev) -+{ -+ int timeout = MSM8953_APM_SWITCH_TIMEOUT_US; -+ u32 regval; -+ int ret = 0; -+ unsigned long flags; -+ -+ spin_lock_irqsave(&ctrl_dev->lock, flags); -+ -+ /* Switch arrays to APCC supply and wait for its completion */ -+ writel_relaxed(MSM8953_APM_APCC_MODE_VAL, ctrl_dev->reg_base + -+ MSM8953_APCC_APM_MODE); -+ -+ /* Ensure write above completes before delaying */ -+ mb(); -+ -+ while (timeout > 0) { -+ regval = readl_relaxed(ctrl_dev->reg_base + -+ MSM8953_APCC_APM_CTL_STS); -+ if ((regval & MSM8953_APM_CTL_STS_MASK) == -+ MSM8953_APM_APCC_DONE_VAL) -+ break; -+ -+ udelay(1); -+ timeout--; -+ } -+ -+ if (timeout == 0) { -+ ret = -ETIMEDOUT; -+ dev_err(ctrl_dev->dev, "MX to APCC APM switch timed out. APCC_APM_CTL_STS=0x%x\n", -+ regval); -+ } else { -+ ctrl_dev->supply = MSM_APM_SUPPLY_APCC; -+ dev_dbg(ctrl_dev->dev, "APM supply switched to APCC\n"); -+ } -+ -+ spin_unlock_irqrestore(&ctrl_dev->lock, flags); -+ -+ return ret; -+} -+ -+static int msm_apm_switch_to_mx(struct msm_apm_ctrl_dev *ctrl_dev) -+{ -+ int ret = 0; -+ -+ switch (ctrl_dev->msm_id) { -+ case MSM8996_ID: -+ ret = msm8996_apm_switch_to_mx(ctrl_dev); -+ break; -+ case MSM8953_ID: -+ case IPQ807x_ID: -+ ret = msm8953_apm_switch_to_mx(ctrl_dev); -+ break; -+ } -+ -+ return ret; -+} -+ -+static int msm_apm_switch_to_apcc(struct msm_apm_ctrl_dev *ctrl_dev) -+{ -+ int ret = 0; -+ -+ switch (ctrl_dev->msm_id) { -+ case MSM8996_ID: -+ ret = msm8996_apm_switch_to_apcc(ctrl_dev); -+ break; -+ case MSM8953_ID: -+ case IPQ807x_ID: -+ ret = msm8953_apm_switch_to_apcc(ctrl_dev); -+ break; -+ } -+ -+ return ret; -+} -+ -+/** -+ * msm_apm_get_supply() - Returns the supply that is currently -+ * powering the memory arrays -+ * @ctrl_dev: Pointer to an MSM APM controller device -+ * -+ * Returns the supply currently selected by the APM. -+ */ -+int msm_apm_get_supply(struct msm_apm_ctrl_dev *ctrl_dev) -+{ -+ return ctrl_dev->supply; -+} -+EXPORT_SYMBOL(msm_apm_get_supply); -+ -+/** -+ * msm_apm_set_supply() - Perform the necessary steps to switch the voltage -+ * source of the memory arrays to a given supply -+ * @ctrl_dev: Pointer to an MSM APM controller device -+ * @supply: Power rail to use as supply for the memory -+ * arrays -+ * -+ * Returns 0 on success, -ETIMEDOUT on APM switch timeout, or -EPERM if -+ * the supply is not supported. -+ */ -+int msm_apm_set_supply(struct msm_apm_ctrl_dev *ctrl_dev, -+ enum msm_apm_supply supply) -+{ -+ int ret; -+ -+ switch (supply) { -+ case MSM_APM_SUPPLY_APCC: -+ ret = msm_apm_switch_to_apcc(ctrl_dev); -+ break; -+ case MSM_APM_SUPPLY_MX: -+ ret = msm_apm_switch_to_mx(ctrl_dev); -+ break; -+ default: -+ ret = -EPERM; -+ break; -+ } -+ -+ return ret; -+} -+EXPORT_SYMBOL(msm_apm_set_supply); -+ -+/** -+ * msm_apm_ctrl_dev_get() - get a handle to the MSM APM controller linked to -+ * the device in device tree -+ * @dev: Pointer to the device -+ * -+ * The device must specify "qcom,apm-ctrl" property in its device tree -+ * node which points to an MSM APM controller device node. -+ * -+ * Returns an MSM APM controller handle if successful or ERR_PTR on any error. -+ * If the APM controller device hasn't probed yet, ERR_PTR(-EPROBE_DEFER) is -+ * returned. -+ */ -+struct msm_apm_ctrl_dev *msm_apm_ctrl_dev_get(struct device *dev) -+{ -+ struct msm_apm_ctrl_dev *ctrl_dev = NULL; -+ struct msm_apm_ctrl_dev *dev_found = ERR_PTR(-EPROBE_DEFER); -+ struct device_node *ctrl_node; -+ -+ if (!dev || !dev->of_node) { -+ pr_err("Invalid device node\n"); -+ return ERR_PTR(-EINVAL); -+ } -+ -+ ctrl_node = of_parse_phandle(dev->of_node, "qcom,apm-ctrl", 0); -+ if (!ctrl_node) { -+ pr_err("Could not find qcom,apm-ctrl property in %s\n", -+ dev->of_node->full_name); -+ return ERR_PTR(-ENXIO); -+ } -+ -+ mutex_lock(&apm_ctrl_list_mutex); -+ list_for_each_entry(ctrl_dev, &apm_ctrl_list, list) { -+ if (ctrl_dev->dev && ctrl_dev->dev->of_node == ctrl_node) { -+ dev_found = ctrl_dev; -+ break; -+ } -+ } -+ mutex_unlock(&apm_ctrl_list_mutex); -+ -+ of_node_put(ctrl_node); -+ return dev_found; -+} -+EXPORT_SYMBOL(msm_apm_ctrl_dev_get); -+ -+#if defined(CONFIG_DEBUG_FS) -+ -+static int apm_supply_dbg_open(struct inode *inode, struct file *filep) -+{ -+ filep->private_data = inode->i_private; -+ -+ return 0; -+} -+ -+static ssize_t apm_supply_dbg_read(struct file *filep, char __user *ubuf, -+ size_t count, loff_t *ppos) -+{ -+ struct msm_apm_ctrl_dev *ctrl_dev = filep->private_data; -+ char buf[10]; -+ int len; -+ -+ if (!ctrl_dev) { -+ pr_err("invalid apm ctrl handle\n"); -+ return -ENODEV; -+ } -+ -+ if (ctrl_dev->supply == MSM_APM_SUPPLY_APCC) -+ len = snprintf(buf, sizeof(buf), "APCC\n"); -+ else if (ctrl_dev->supply == MSM_APM_SUPPLY_MX) -+ len = snprintf(buf, sizeof(buf), "MX\n"); -+ else -+ len = snprintf(buf, sizeof(buf), "ERR\n"); -+ -+ return simple_read_from_buffer(ubuf, count, ppos, buf, len); -+} -+ -+static const struct file_operations apm_supply_fops = { -+ .open = apm_supply_dbg_open, -+ .read = apm_supply_dbg_read, -+}; -+ -+static void apm_debugfs_base_init(void) -+{ -+ apm_debugfs_base = debugfs_create_dir("msm-apm", NULL); -+ -+ if (IS_ERR_OR_NULL(apm_debugfs_base)) -+ pr_err("msm-apm debugfs base directory creation failed\n"); -+} -+ -+static void apm_debugfs_init(struct msm_apm_ctrl_dev *ctrl_dev) -+{ -+ struct dentry *temp; -+ -+ if (IS_ERR_OR_NULL(apm_debugfs_base)) { -+ pr_err("Base directory missing, cannot create apm debugfs nodes\n"); -+ return; -+ } -+ -+ ctrl_dev->debugfs = debugfs_create_dir(dev_name(ctrl_dev->dev), -+ apm_debugfs_base); -+ if (IS_ERR_OR_NULL(ctrl_dev->debugfs)) { -+ pr_err("%s debugfs directory creation failed\n", -+ dev_name(ctrl_dev->dev)); -+ return; -+ } -+ -+ temp = debugfs_create_file("supply", S_IRUGO, ctrl_dev->debugfs, -+ ctrl_dev, &apm_supply_fops); -+ if (IS_ERR_OR_NULL(temp)) { -+ pr_err("supply mode creation failed\n"); -+ return; -+ } -+} -+ -+static void apm_debugfs_deinit(struct msm_apm_ctrl_dev *ctrl_dev) -+{ -+ if (!IS_ERR_OR_NULL(ctrl_dev->debugfs)) -+ debugfs_remove_recursive(ctrl_dev->debugfs); -+} -+ -+static void apm_debugfs_base_remove(void) -+{ -+ debugfs_remove_recursive(apm_debugfs_base); -+} -+#else -+ -+static void apm_debugfs_base_init(void) -+{} -+ -+static void apm_debugfs_init(struct msm_apm_ctrl_dev *ctrl_dev) -+{} -+ -+static void apm_debugfs_deinit(struct msm_apm_ctrl_dev *ctrl_dev) -+{} -+ -+static void apm_debugfs_base_remove(void) -+{} -+ -+#endif -+ -+static struct of_device_id msm_apm_match_table[] = { -+ { -+ .compatible = "qcom,msm-apm", -+ .data = (void *)(uintptr_t)MSM8996_ID, -+ }, -+ { -+ .compatible = "qcom,msm8953-apm", -+ .data = (void *)(uintptr_t)MSM8953_ID, -+ }, -+ { -+ .compatible = "qcom,ipq807x-apm", -+ .data = (void *)(uintptr_t)IPQ807x_ID, -+ }, -+ {} -+}; -+ -+static int msm_apm_probe(struct platform_device *pdev) -+{ -+ struct device *dev = &pdev->dev; -+ struct msm_apm_ctrl_dev *ctrl; -+ const struct of_device_id *match; -+ int ret = 0; -+ -+ dev_dbg(dev, "probing MSM Array Power Mux driver\n"); -+ -+ if (!dev->of_node) { -+ dev_err(dev, "Device tree node is missing\n"); -+ return -ENODEV; -+ } -+ -+ match = of_match_device(msm_apm_match_table, dev); -+ if (!match) -+ return -ENODEV; -+ -+ ctrl = devm_kzalloc(dev, sizeof(*ctrl), GFP_KERNEL); -+ if (!ctrl) { -+ dev_err(dev, "MSM APM controller memory allocation failed\n"); -+ return -ENOMEM; -+ } -+ -+ INIT_LIST_HEAD(&ctrl->list); -+ spin_lock_init(&ctrl->lock); -+ ctrl->dev = dev; -+ ctrl->msm_id = (uintptr_t)match->data; -+ platform_set_drvdata(pdev, ctrl); -+ -+ switch (ctrl->msm_id) { -+ case MSM8996_ID: -+ ret = msm_apm_ctrl_devm_ioremap(pdev, ctrl); -+ if (ret) { -+ dev_err(dev, "Failed to add APM controller device\n"); -+ return ret; -+ } -+ break; -+ case MSM8953_ID: -+ case IPQ807x_ID: -+ ret = msm8953_apm_ctrl_init(pdev, ctrl); -+ if (ret) { -+ dev_err(dev, "Failed to initialize APM controller device: ret=%d\n", -+ ret); -+ return ret; -+ } -+ break; -+ default: -+ dev_err(dev, "unable to add APM controller device for msm_id:%d\n", -+ ctrl->msm_id); -+ return -ENODEV; -+ } -+ -+ apm_debugfs_init(ctrl); -+ mutex_lock(&apm_ctrl_list_mutex); -+ list_add_tail(&ctrl->list, &apm_ctrl_list); -+ mutex_unlock(&apm_ctrl_list_mutex); -+ -+ dev_dbg(dev, "MSM Array Power Mux driver probe successful"); -+ -+ return ret; -+} -+ -+static int msm_apm_remove(struct platform_device *pdev) -+{ -+ struct msm_apm_ctrl_dev *ctrl_dev; -+ -+ ctrl_dev = platform_get_drvdata(pdev); -+ if (ctrl_dev) { -+ mutex_lock(&apm_ctrl_list_mutex); -+ list_del(&ctrl_dev->list); -+ mutex_unlock(&apm_ctrl_list_mutex); -+ apm_debugfs_deinit(ctrl_dev); -+ } -+ -+ return 0; -+} -+ -+static struct platform_driver msm_apm_driver = { -+ .driver = { -+ .name = MSM_APM_DRIVER_NAME, -+ .of_match_table = msm_apm_match_table, -+ .owner = THIS_MODULE, -+ }, -+ .probe = msm_apm_probe, -+ .remove = msm_apm_remove, -+}; -+ -+static int __init msm_apm_init(void) -+{ -+ apm_debugfs_base_init(); -+ return platform_driver_register(&msm_apm_driver); -+} -+ -+static void __exit msm_apm_exit(void) -+{ -+ platform_driver_unregister(&msm_apm_driver); -+ apm_debugfs_base_remove(); -+} -+ -+arch_initcall(msm_apm_init); -+module_exit(msm_apm_exit); -+ -+MODULE_DESCRIPTION("MSM Array Power Mux driver"); -+MODULE_LICENSE("GPL v2"); ---- /dev/null -+++ b/include/linux/power/qcom/apm.h -@@ -0,0 +1,48 @@ -+/* -+ * Copyright (c) 2015, The Linux Foundation. All rights reserved. -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 and -+ * only version 2 as published by the Free Software Foundation. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ */ -+ -+#ifndef __LINUX_POWER_QCOM_APM_H__ -+#define __LINUX_POWER_QCOM_APM_H__ -+ -+#include -+#include -+ -+/** -+ * enum msm_apm_supply - supported power rails to supply memory arrays -+ * %MSM_APM_SUPPLY_APCC: to enable selection of VDD_APCC rail as supply -+ * %MSM_APM_SUPPLY_MX: to enable selection of VDD_MX rail as supply -+ */ -+enum msm_apm_supply { -+ MSM_APM_SUPPLY_APCC, -+ MSM_APM_SUPPLY_MX, -+}; -+ -+/* Handle used to identify an APM controller device */ -+struct msm_apm_ctrl_dev; -+ -+#ifdef CONFIG_QCOM_APM -+struct msm_apm_ctrl_dev *msm_apm_ctrl_dev_get(struct device *dev); -+int msm_apm_set_supply(struct msm_apm_ctrl_dev *ctrl_dev, -+ enum msm_apm_supply supply); -+int msm_apm_get_supply(struct msm_apm_ctrl_dev *ctrl_dev); -+ -+#else -+static inline struct msm_apm_ctrl_dev *msm_apm_ctrl_dev_get(struct device *dev) -+{ return ERR_PTR(-EPERM); } -+static inline int msm_apm_set_supply(struct msm_apm_ctrl_dev *ctrl_dev, -+ enum msm_apm_supply supply) -+{ return -EPERM; } -+static inline int msm_apm_get_supply(struct msm_apm_ctrl_dev *ctrl_dev) -+{ return -EPERM; } -+#endif -+#endif diff --git a/target/linux/qualcommax/patches-6.1/0901-regulator-add-Qualcomm-CPR-regulators.patch b/target/linux/qualcommax/patches-6.1/0901-regulator-add-Qualcomm-CPR-regulators.patch deleted file mode 100644 index 9b9f7159f3..0000000000 --- a/target/linux/qualcommax/patches-6.1/0901-regulator-add-Qualcomm-CPR-regulators.patch +++ /dev/null @@ -1,12144 +0,0 @@ -From c9df32c057e43e38c8113199e64f7a64f8d341df Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Mon, 11 Apr 2022 14:35:36 +0200 -Subject: [PATCH] regulator: add Qualcomm CPR regulators - -Allow building Qualcomm CPR regulators. - -Signed-off-by: Robert Marko ---- - drivers/regulator/Kconfig | 33 + - drivers/regulator/Makefile | 3 + - drivers/regulator/cpr3-npu-regulator.c | 695 +++ - drivers/regulator/cpr3-regulator.c | 5111 +++++++++++++++++++++++ - drivers/regulator/cpr3-regulator.h | 1211 ++++++ - drivers/regulator/cpr3-util.c | 2750 ++++++++++++ - drivers/regulator/cpr4-apss-regulator.c | 1819 ++++++++ - include/soc/qcom/socinfo.h | 463 ++ - 8 files changed, 12085 insertions(+) - create mode 100644 drivers/regulator/cpr3-npu-regulator.c - create mode 100644 drivers/regulator/cpr3-regulator.c - create mode 100644 drivers/regulator/cpr3-regulator.h - create mode 100644 drivers/regulator/cpr3-util.c - create mode 100644 drivers/regulator/cpr4-apss-regulator.c - create mode 100644 include/soc/qcom/socinfo.h - ---- a/drivers/regulator/Kconfig -+++ b/drivers/regulator/Kconfig -@@ -1524,4 +1524,37 @@ config REGULATOR_QCOM_LABIBB - boost regulator and IBB can be used as a negative boost regulator - for LCD display panel. - -+config REGULATOR_CPR3 -+ bool "QCOM CPR3 regulator core support" -+ help -+ This driver supports Core Power Reduction (CPR) version 3 controllers -+ which are used by some Qualcomm Technologies, Inc. SoCs to -+ manage important voltage regulators. CPR3 controllers are capable of -+ monitoring several ring oscillator sensing loops simultaneously. The -+ CPR3 controller informs software when the silicon conditions require -+ the supply voltage to be increased or decreased. On certain supply -+ rails, the CPR3 controller is able to propagate the voltage increase -+ or decrease requests all the way to the PMIC without software -+ involvement. -+ -+config REGULATOR_CPR3_NPU -+ bool "QCOM CPR3 regulator for NPU" -+ depends on OF && REGULATOR_CPR3 -+ help -+ This driver supports Qualcomm Technologies, Inc. NPU CPR3 -+ regulator Which will always operate in open loop. -+ -+config REGULATOR_CPR4_APSS -+ bool "QCOM CPR4 regulator for APSS" -+ depends on OF && REGULATOR_CPR3 -+ help -+ This driver supports Qualcomm Technologies, Inc. APSS application -+ processor specific features including memory array power mux (APM) -+ switching, one CPR4 thread which monitor the two APSS clusters that -+ are both powered by a shared supply, hardware closed-loop auto -+ voltage stepping, voltage adjustments based on online core count, -+ voltage adjustments based on temperature readings, and voltage -+ adjustments for performance boost mode. This driver reads both initial -+ voltage and CPR target quotient values out of hardware fuses. -+ - endif ---- a/drivers/regulator/Makefile -+++ b/drivers/regulator/Makefile -@@ -110,6 +110,9 @@ obj-$(CONFIG_REGULATOR_QCOM_RPMH) += qco - obj-$(CONFIG_REGULATOR_QCOM_SMD_RPM) += qcom_smd-regulator.o - obj-$(CONFIG_REGULATOR_QCOM_SPMI) += qcom_spmi-regulator.o - obj-$(CONFIG_REGULATOR_QCOM_USB_VBUS) += qcom_usb_vbus-regulator.o -+obj-$(CONFIG_REGULATOR_CPR3) += cpr3-regulator.o cpr3-util.o -+obj-$(CONFIG_REGULATOR_CPR3_NPU) += cpr3-npu-regulator.o -+obj-$(CONFIG_REGULATOR_CPR4_APSS) += cpr4-apss-regulator.o - obj-$(CONFIG_REGULATOR_PALMAS) += palmas-regulator.o - obj-$(CONFIG_REGULATOR_PCA9450) += pca9450-regulator.o - obj-$(CONFIG_REGULATOR_PF8X00) += pf8x00-regulator.o ---- /dev/null -+++ b/drivers/regulator/cpr3-npu-regulator.c -@@ -0,0 +1,695 @@ -+/* -+ * Copyright (c) 2017, The Linux Foundation. All rights reserved. -+ * -+ * Permission to use, copy, modify, and/or distribute this software for any -+ * purpose with or without fee is hereby granted, provided that the above -+ * copyright notice and this permission notice appear in all copies. -+ * -+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES -+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF -+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR -+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES -+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN -+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF -+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. -+ */ -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#include "cpr3-regulator.h" -+ -+#define IPQ807x_NPU_FUSE_CORNERS 2 -+#define IPQ817x_NPU_FUSE_CORNERS 1 -+#define IPQ807x_NPU_FUSE_STEP_VOLT 8000 -+#define IPQ807x_NPU_VOLTAGE_FUSE_SIZE 6 -+#define IPQ807x_NPU_CPR_CLOCK_RATE 19200000 -+ -+#define IPQ807x_NPU_CPR_TCSR_START 6 -+#define IPQ807x_NPU_CPR_TCSR_END 7 -+ -+#define NPU_TSENS 5 -+ -+u32 g_valid_npu_fuse_count = IPQ807x_NPU_FUSE_CORNERS; -+/** -+ * struct cpr3_ipq807x_npu_fuses - NPU specific fuse data for IPQ807x -+ * @init_voltage: Initial (i.e. open-loop) voltage fuse parameter value -+ * for each fuse corner (raw, not converted to a voltage) -+ * This struct holds the values for all of the fuses read from memory. -+ */ -+struct cpr3_ipq807x_npu_fuses { -+ u64 init_voltage[IPQ807x_NPU_FUSE_CORNERS]; -+}; -+ -+/* -+ * Constants which define the name of each fuse corner. -+ */ -+enum cpr3_ipq807x_npu_fuse_corner { -+ CPR3_IPQ807x_NPU_FUSE_CORNER_NOM = 0, -+ CPR3_IPQ807x_NPU_FUSE_CORNER_TURBO = 1, -+}; -+ -+static const char * const cpr3_ipq807x_npu_fuse_corner_name[] = { -+ [CPR3_IPQ807x_NPU_FUSE_CORNER_NOM] = "NOM", -+ [CPR3_IPQ807x_NPU_FUSE_CORNER_TURBO] = "TURBO", -+}; -+ -+/* -+ * IPQ807x NPU fuse parameter locations: -+ * -+ * Structs are organized with the following dimensions: -+ * Outer: 0 to 1 for fuse corners from lowest to highest corner -+ * Inner: large enough to hold the longest set of parameter segments which -+ * fully defines a fuse parameter, +1 (for NULL termination). -+ * Each segment corresponds to a contiguous group of bits from a -+ * single fuse row. These segments are concatentated together in -+ * order to form the full fuse parameter value. The segments for -+ * a given parameter may correspond to different fuse rows. -+ */ -+static struct cpr3_fuse_param -+ipq807x_npu_init_voltage_param[IPQ807x_NPU_FUSE_CORNERS][2] = { -+ {{73, 22, 27}, {} }, -+ {{73, 16, 21}, {} }, -+}; -+ -+/* -+ * Open loop voltage fuse reference voltages in microvolts for IPQ807x -+ */ -+static int -+ipq807x_npu_fuse_ref_volt [IPQ807x_NPU_FUSE_CORNERS] = { -+ 912000, -+ 992000, -+}; -+ -+/* -+ * IPQ9574 (Few parameters are changed, remaining are same as IPQ807x) -+ */ -+#define IPQ9574_NPU_FUSE_CORNERS 2 -+#define IPQ9574_NPU_FUSE_STEP_VOLT 10000 -+#define IPQ9574_NPU_CPR_CLOCK_RATE 24000000 -+ -+/* -+ * fues parameters for IPQ9574 -+ */ -+static struct cpr3_fuse_param -+ipq9574_npu_init_voltage_param[IPQ9574_NPU_FUSE_CORNERS][2] = { -+ {{105, 12, 17}, {} }, -+ {{105, 6, 11}, {} }, -+}; -+ -+/* -+ * Open loop voltage fuse reference voltages in microvolts for IPQ9574 -+ */ -+static int -+ipq9574_npu_fuse_ref_volt [IPQ9574_NPU_FUSE_CORNERS] = { -+ 862500, -+ 987500, -+}; -+ -+struct cpr3_controller *g_ctrl; -+ -+void cpr3_npu_temp_notify(int sensor, int temp, int low_notif) -+{ -+ u32 prev_sensor_state; -+ -+ if (sensor != NPU_TSENS) -+ return; -+ -+ prev_sensor_state = g_ctrl->cur_sensor_state; -+ if (low_notif) -+ g_ctrl->cur_sensor_state |= BIT(sensor); -+ else -+ g_ctrl->cur_sensor_state &= ~BIT(sensor); -+ -+ if (!prev_sensor_state && g_ctrl->cur_sensor_state) -+ cpr3_handle_temp_open_loop_adjustment(g_ctrl, true); -+ else if (prev_sensor_state && !g_ctrl->cur_sensor_state) -+ cpr3_handle_temp_open_loop_adjustment(g_ctrl, false); -+} -+ -+/** -+ * cpr3_ipq807x_npu_read_fuse_data() - load NPU specific fuse parameter values -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * This function allocates a cpr3_ipq807x_npu_fuses struct, fills it with -+ * values read out of hardware fuses, and finally copies common fuse values -+ * into the CPR3 regulator struct. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_ipq807x_npu_read_fuse_data(struct cpr3_regulator *vreg) -+{ -+ void __iomem *base = vreg->thread->ctrl->fuse_base; -+ struct cpr3_ipq807x_npu_fuses *fuse; -+ int i, rc; -+ -+ fuse = devm_kzalloc(vreg->thread->ctrl->dev, sizeof(*fuse), GFP_KERNEL); -+ if (!fuse) -+ return -ENOMEM; -+ -+ for (i = 0; i < g_valid_npu_fuse_count; i++) { -+ rc = cpr3_read_fuse_param(base, -+ vreg->cpr3_regulator_data->init_voltage_param[i], -+ &fuse->init_voltage[i]); -+ if (rc) { -+ cpr3_err(vreg, "Unable to read fuse-corner %d initial voltage fuse, rc=%d\n", -+ i, rc); -+ return rc; -+ } -+ } -+ -+ vreg->fuse_corner_count = g_valid_npu_fuse_count; -+ vreg->platform_fuses = fuse; -+ -+ return 0; -+} -+ -+/** -+ * cpr3_npu_parse_corner_data() - parse NPU corner data from device tree -+ * properties of the CPR3 regulator's device node -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_npu_parse_corner_data(struct cpr3_regulator *vreg) -+{ -+ int rc; -+ -+ rc = cpr3_parse_common_corner_data(vreg); -+ if (rc) { -+ cpr3_err(vreg, "error reading corner data, rc=%d\n", rc); -+ return rc; -+ } -+ -+ return rc; -+} -+ -+/** -+ * cpr3_ipq807x_npu_calculate_open_loop_voltages() - calculate the open-loop -+ * voltage for each corner of a CPR3 regulator -+ * @vreg: Pointer to the CPR3 regulator -+ * @temp_correction: Temperature based correction -+ * -+ * If open-loop voltage interpolation is allowed in device tree, then -+ * this function calculates the open-loop voltage for a given corner using -+ * linear interpolation. This interpolation is performed using the processor -+ * frequencies of the lower and higher Fmax corners along with their fused -+ * open-loop voltages. -+ * -+ * If open-loop voltage interpolation is not allowed, then this function uses -+ * the Fmax fused open-loop voltage for all of the corners associated with a -+ * given fuse corner. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_ipq807x_npu_calculate_open_loop_voltages( -+ struct cpr3_regulator *vreg, bool temp_correction) -+{ -+ struct cpr3_ipq807x_npu_fuses *fuse = vreg->platform_fuses; -+ struct cpr3_controller *ctrl = vreg->thread->ctrl; -+ int i, j, rc = 0; -+ u64 freq_low, volt_low, freq_high, volt_high; -+ int *fuse_volt; -+ int *fmax_corner; -+ -+ fuse_volt = kcalloc(vreg->fuse_corner_count, sizeof(*fuse_volt), -+ GFP_KERNEL); -+ fmax_corner = kcalloc(vreg->fuse_corner_count, sizeof(*fmax_corner), -+ GFP_KERNEL); -+ if (!fuse_volt || !fmax_corner) { -+ rc = -ENOMEM; -+ goto done; -+ } -+ -+ for (i = 0; i < vreg->fuse_corner_count; i++) { -+ if (ctrl->cpr_global_setting == CPR_DISABLED) -+ fuse_volt[i] = vreg->cpr3_regulator_data->fuse_ref_volt[i]; -+ else -+ fuse_volt[i] = cpr3_convert_open_loop_voltage_fuse( -+ vreg->cpr3_regulator_data->fuse_ref_volt[i], -+ vreg->cpr3_regulator_data->fuse_step_volt, -+ fuse->init_voltage[i], -+ IPQ807x_NPU_VOLTAGE_FUSE_SIZE); -+ -+ /* Log fused open-loop voltage values for debugging purposes. */ -+ cpr3_info(vreg, "fused %8s: open-loop=%7d uV\n", -+ cpr3_ipq807x_npu_fuse_corner_name[i], -+ fuse_volt[i]); -+ } -+ -+ rc = cpr3_determine_part_type(vreg, -+ fuse_volt[CPR3_IPQ807x_NPU_FUSE_CORNER_TURBO]); -+ if (rc) { -+ cpr3_err(vreg, -+ "fused part type detection failed failed, rc=%d\n", rc); -+ goto done; -+ } -+ -+ rc = cpr3_adjust_fused_open_loop_voltages(vreg, fuse_volt); -+ if (rc) { -+ cpr3_err(vreg, -+ "fused open-loop voltage adjustment failed, rc=%d\n", -+ rc); -+ goto done; -+ } -+ if (temp_correction) { -+ rc = cpr3_determine_temp_base_open_loop_correction(vreg, -+ fuse_volt); -+ if (rc) { -+ cpr3_err(vreg, -+ "temp open-loop voltage adj. failed, rc=%d\n", -+ rc); -+ goto done; -+ } -+ } -+ -+ for (i = 1; i < vreg->fuse_corner_count; i++) { -+ if (fuse_volt[i] < fuse_volt[i - 1]) { -+ cpr3_info(vreg, -+ "fuse corner %d voltage=%d uV < fuse corner %d \ -+ voltage=%d uV; overriding: fuse corner %d \ -+ voltage=%d\n", -+ i, fuse_volt[i], i - 1, fuse_volt[i - 1], -+ i, fuse_volt[i - 1]); -+ fuse_volt[i] = fuse_volt[i - 1]; -+ } -+ } -+ -+ /* Determine highest corner mapped to each fuse corner */ -+ j = vreg->fuse_corner_count - 1; -+ for (i = vreg->corner_count - 1; i >= 0; i--) { -+ if (vreg->corner[i].cpr_fuse_corner == j) { -+ fmax_corner[j] = i; -+ j--; -+ } -+ } -+ -+ if (j >= 0) { -+ cpr3_err(vreg, "invalid fuse corner mapping\n"); -+ rc = -EINVAL; -+ goto done; -+ } -+ -+ /* -+ * Interpolation is not possible for corners mapped to the lowest fuse -+ * corner so use the fuse corner value directly. -+ */ -+ for (i = 0; i <= fmax_corner[0]; i++) -+ vreg->corner[i].open_loop_volt = fuse_volt[0]; -+ -+ /* Interpolate voltages for the higher fuse corners. */ -+ for (i = 1; i < vreg->fuse_corner_count; i++) { -+ freq_low = vreg->corner[fmax_corner[i - 1]].proc_freq; -+ volt_low = fuse_volt[i - 1]; -+ freq_high = vreg->corner[fmax_corner[i]].proc_freq; -+ volt_high = fuse_volt[i]; -+ -+ for (j = fmax_corner[i - 1] + 1; j <= fmax_corner[i]; j++) -+ vreg->corner[j].open_loop_volt = cpr3_interpolate( -+ freq_low, volt_low, freq_high, volt_high, -+ vreg->corner[j].proc_freq); -+ } -+ -+done: -+ if (rc == 0) { -+ cpr3_debug(vreg, "unadjusted per-corner open-loop voltages:\n"); -+ for (i = 0; i < vreg->corner_count; i++) -+ cpr3_debug(vreg, "open-loop[%2d] = %d uV\n", i, -+ vreg->corner[i].open_loop_volt); -+ -+ rc = cpr3_adjust_open_loop_voltages(vreg); -+ if (rc) -+ cpr3_err(vreg, -+ "open-loop voltage adjustment failed, rc=%d\n", -+ rc); -+ } -+ -+ kfree(fuse_volt); -+ kfree(fmax_corner); -+ return rc; -+} -+ -+/** -+ * cpr3_npu_print_settings() - print out NPU CPR configuration settings into -+ * the kernel log for debugging purposes -+ * @vreg: Pointer to the CPR3 regulator -+ */ -+static void cpr3_npu_print_settings(struct cpr3_regulator *vreg) -+{ -+ struct cpr3_corner *corner; -+ int i; -+ -+ cpr3_debug(vreg, -+ "Corner: Frequency (Hz), Fuse Corner, Floor (uV), \ -+ Open-Loop (uV), Ceiling (uV)\n"); -+ for (i = 0; i < vreg->corner_count; i++) { -+ corner = &vreg->corner[i]; -+ cpr3_debug(vreg, "%3d: %10u, %2d, %7d, %7d, %7d\n", -+ i, corner->proc_freq, corner->cpr_fuse_corner, -+ corner->floor_volt, corner->open_loop_volt, -+ corner->ceiling_volt); -+ } -+ -+ if (vreg->thread->ctrl->apm) -+ cpr3_debug(vreg, "APM threshold = %d uV, APM adjust = %d uV\n", -+ vreg->thread->ctrl->apm_threshold_volt, -+ vreg->thread->ctrl->apm_adj_volt); -+} -+ -+/** -+ * cpr3_ipq807x_npu_calc_temp_based_ol_voltages() - Calculate the open loop -+ * voltages based on temperature based correction margins -+ * @vreg: Pointer to the CPR3 regulator -+ */ -+ -+static int -+cpr3_ipq807x_npu_calc_temp_based_ol_voltages(struct cpr3_regulator *vreg, -+ bool temp_correction) -+{ -+ int rc, i; -+ -+ rc = cpr3_ipq807x_npu_calculate_open_loop_voltages(vreg, -+ temp_correction); -+ if (rc) { -+ cpr3_err(vreg, -+ "unable to calculate open-loop voltages, rc=%d\n", rc); -+ return rc; -+ } -+ -+ rc = cpr3_limit_open_loop_voltages(vreg); -+ if (rc) { -+ cpr3_err(vreg, "unable to limit open-loop voltages, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ cpr3_open_loop_voltage_as_ceiling(vreg); -+ -+ rc = cpr3_limit_floor_voltages(vreg); -+ if (rc) { -+ cpr3_err(vreg, "unable to limit floor voltages, rc=%d\n", rc); -+ return rc; -+ } -+ -+ for (i = 0; i < vreg->corner_count; i++) { -+ if (temp_correction) -+ vreg->corner[i].cold_temp_open_loop_volt = -+ vreg->corner[i].open_loop_volt; -+ else -+ vreg->corner[i].normal_temp_open_loop_volt = -+ vreg->corner[i].open_loop_volt; -+ } -+ -+ cpr3_npu_print_settings(vreg); -+ -+ return rc; -+} -+ -+/** -+ * cpr3_npu_init_thread() - perform steps necessary to initialize the -+ * configuration data for a CPR3 thread -+ * @thread: Pointer to the CPR3 thread -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_npu_init_thread(struct cpr3_thread *thread) -+{ -+ int rc; -+ -+ rc = cpr3_parse_common_thread_data(thread); -+ if (rc) { -+ cpr3_err(thread->ctrl, -+ "thread %u CPR thread data from DT- failed, rc=%d\n", -+ thread->thread_id, rc); -+ return rc; -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr3_npu_init_regulator() - perform all steps necessary to initialize the -+ * configuration data for a CPR3 regulator -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_npu_init_regulator(struct cpr3_regulator *vreg) -+{ -+ struct cpr3_ipq807x_npu_fuses *fuse; -+ int rc, cold_temp = 0; -+ bool can_adj_cold_temp = cpr3_can_adjust_cold_temp(vreg); -+ -+ rc = cpr3_ipq807x_npu_read_fuse_data(vreg); -+ if (rc) { -+ cpr3_err(vreg, "unable to read CPR fuse data, rc=%d\n", rc); -+ return rc; -+ } -+ -+ fuse = vreg->platform_fuses; -+ -+ rc = cpr3_npu_parse_corner_data(vreg); -+ if (rc) { -+ cpr3_err(vreg, -+ "Cannot read CPR corner data from DT, rc=%d\n", rc); -+ return rc; -+ } -+ -+ rc = cpr3_mem_acc_init(vreg); -+ if (rc) { -+ if (rc != -EPROBE_DEFER) -+ cpr3_err(vreg, -+ "Cannot initialize mem-acc regulator settings, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ if (can_adj_cold_temp) { -+ rc = cpr3_ipq807x_npu_calc_temp_based_ol_voltages(vreg, true); -+ if (rc) { -+ cpr3_err(vreg, -+ "unable to calculate open-loop voltages, rc=%d\n", rc); -+ return rc; -+ } -+ } -+ -+ rc = cpr3_ipq807x_npu_calc_temp_based_ol_voltages(vreg, false); -+ if (rc) { -+ cpr3_err(vreg, -+ "unable to calculate open-loop voltages, rc=%d\n", rc); -+ return rc; -+ } -+ -+ if (can_adj_cold_temp) { -+ cpr3_info(vreg, -+ "Normal and Cold condition init done. Default to normal.\n"); -+ -+ rc = cpr3_get_cold_temp_threshold(vreg, &cold_temp); -+ if (rc) { -+ cpr3_err(vreg, -+ "Get cold temperature threshold failed, rc=%d\n", rc); -+ return rc; -+ } -+ register_low_temp_notif(NPU_TSENS, cold_temp, -+ cpr3_npu_temp_notify); -+ } -+ -+ return rc; -+} -+ -+/** -+ * cpr3_npu_init_controller() - perform NPU CPR3 controller specific -+ * initializations -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_npu_init_controller(struct cpr3_controller *ctrl) -+{ -+ int rc; -+ -+ rc = cpr3_parse_open_loop_common_ctrl_data(ctrl); -+ if (rc) { -+ if (rc != -EPROBE_DEFER) -+ cpr3_err(ctrl, "unable to parse common controller data, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ ctrl->ctrl_type = CPR_CTRL_TYPE_CPR3; -+ ctrl->supports_hw_closed_loop = false; -+ -+ return 0; -+} -+ -+static const struct cpr3_reg_data ipq807x_cpr_npu = { -+ .cpr_valid_fuse_count = IPQ807x_NPU_FUSE_CORNERS, -+ .init_voltage_param = ipq807x_npu_init_voltage_param, -+ .fuse_ref_volt = ipq807x_npu_fuse_ref_volt, -+ .fuse_step_volt = IPQ807x_NPU_FUSE_STEP_VOLT, -+ .cpr_clk_rate = IPQ807x_NPU_CPR_CLOCK_RATE, -+}; -+ -+static const struct cpr3_reg_data ipq817x_cpr_npu = { -+ .cpr_valid_fuse_count = IPQ817x_NPU_FUSE_CORNERS, -+ .init_voltage_param = ipq807x_npu_init_voltage_param, -+ .fuse_ref_volt = ipq807x_npu_fuse_ref_volt, -+ .fuse_step_volt = IPQ807x_NPU_FUSE_STEP_VOLT, -+ .cpr_clk_rate = IPQ807x_NPU_CPR_CLOCK_RATE, -+}; -+ -+static const struct cpr3_reg_data ipq9574_cpr_npu = { -+ .cpr_valid_fuse_count = IPQ9574_NPU_FUSE_CORNERS, -+ .init_voltage_param = ipq9574_npu_init_voltage_param, -+ .fuse_ref_volt = ipq9574_npu_fuse_ref_volt, -+ .fuse_step_volt = IPQ9574_NPU_FUSE_STEP_VOLT, -+ .cpr_clk_rate = IPQ9574_NPU_CPR_CLOCK_RATE, -+}; -+ -+static struct of_device_id cpr3_regulator_match_table[] = { -+ { -+ .compatible = "qcom,cpr3-ipq807x-npu-regulator", -+ .data = &ipq807x_cpr_npu -+ }, -+ { -+ .compatible = "qcom,cpr3-ipq817x-npu-regulator", -+ .data = &ipq817x_cpr_npu -+ }, -+ { -+ .compatible = "qcom,cpr3-ipq9574-npu-regulator", -+ .data = &ipq9574_cpr_npu -+ }, -+ {} -+}; -+ -+static int cpr3_npu_regulator_probe(struct platform_device *pdev) -+{ -+ struct device *dev = &pdev->dev; -+ struct cpr3_controller *ctrl; -+ int i, rc; -+ const struct of_device_id *match; -+ struct cpr3_reg_data *cpr_data; -+ -+ if (!dev->of_node) { -+ dev_err(dev, "Device tree node is missing\n"); -+ return -EINVAL; -+ } -+ -+ ctrl = devm_kzalloc(dev, sizeof(*ctrl), GFP_KERNEL); -+ if (!ctrl) -+ return -ENOMEM; -+ g_ctrl = ctrl; -+ -+ match = of_match_device(cpr3_regulator_match_table, &pdev->dev); -+ if (!match) -+ return -ENODEV; -+ -+ cpr_data = (struct cpr3_reg_data *)match->data; -+ g_valid_npu_fuse_count = cpr_data->cpr_valid_fuse_count; -+ dev_info(dev, "NPU CPR valid fuse count: %d\n", g_valid_npu_fuse_count); -+ ctrl->cpr_clock_rate = cpr_data->cpr_clk_rate; -+ -+ ctrl->dev = dev; -+ /* Set to false later if anything precludes CPR operation. */ -+ ctrl->cpr_allowed_hw = true; -+ -+ rc = of_property_read_string(dev->of_node, "qcom,cpr-ctrl-name", -+ &ctrl->name); -+ if (rc) { -+ cpr3_err(ctrl, "unable to read qcom,cpr-ctrl-name, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ rc = cpr3_map_fuse_base(ctrl, pdev); -+ if (rc) { -+ cpr3_err(ctrl, "could not map fuse base address\n"); -+ return rc; -+ } -+ -+ rc = cpr3_read_tcsr_setting(ctrl, pdev, IPQ807x_NPU_CPR_TCSR_START, -+ IPQ807x_NPU_CPR_TCSR_END); -+ if (rc) { -+ cpr3_err(ctrl, "could not read CPR tcsr rsetting\n"); -+ return rc; -+ } -+ -+ rc = cpr3_allocate_threads(ctrl, 0, 0); -+ if (rc) { -+ cpr3_err(ctrl, "failed to allocate CPR thread array, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ if (ctrl->thread_count != 1) { -+ cpr3_err(ctrl, "expected 1 thread but found %d\n", -+ ctrl->thread_count); -+ return -EINVAL; -+ } -+ -+ rc = cpr3_npu_init_controller(ctrl); -+ if (rc) { -+ if (rc != -EPROBE_DEFER) -+ cpr3_err(ctrl, "failed to initialize CPR controller parameters, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ rc = cpr3_npu_init_thread(&ctrl->thread[0]); -+ if (rc) { -+ cpr3_err(ctrl, "thread initialization failed, rc=%d\n", rc); -+ return rc; -+ } -+ -+ for (i = 0; i < ctrl->thread[0].vreg_count; i++) { -+ ctrl->thread[0].vreg[i].cpr3_regulator_data = cpr_data; -+ rc = cpr3_npu_init_regulator(&ctrl->thread[0].vreg[i]); -+ if (rc) { -+ cpr3_err(&ctrl->thread[0].vreg[i], "regulator initialization failed, rc=%d\n", -+ rc); -+ return rc; -+ } -+ } -+ -+ platform_set_drvdata(pdev, ctrl); -+ -+ return cpr3_open_loop_regulator_register(pdev, ctrl); -+} -+ -+static int cpr3_npu_regulator_remove(struct platform_device *pdev) -+{ -+ struct cpr3_controller *ctrl = platform_get_drvdata(pdev); -+ -+ return cpr3_open_loop_regulator_unregister(ctrl); -+} -+ -+static struct platform_driver cpr3_npu_regulator_driver = { -+ .driver = { -+ .name = "qcom,cpr3-npu-regulator", -+ .of_match_table = cpr3_regulator_match_table, -+ .owner = THIS_MODULE, -+ }, -+ .probe = cpr3_npu_regulator_probe, -+ .remove = cpr3_npu_regulator_remove, -+}; -+ -+static int cpr3_regulator_init(void) -+{ -+ return platform_driver_register(&cpr3_npu_regulator_driver); -+} -+arch_initcall(cpr3_regulator_init); -+ -+static void cpr3_regulator_exit(void) -+{ -+ platform_driver_unregister(&cpr3_npu_regulator_driver); -+} -+module_exit(cpr3_regulator_exit); -+ -+MODULE_DESCRIPTION("QCOM CPR3 NPU regulator driver"); -+MODULE_LICENSE("Dual BSD/GPLv2"); -+MODULE_ALIAS("platform:npu-ipq807x"); ---- /dev/null -+++ b/drivers/regulator/cpr3-regulator.c -@@ -0,0 +1,5111 @@ -+/* -+ * Copyright (c) 2015-2017, The Linux Foundation. All rights reserved. -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 and -+ * only version 2 as published by the Free Software Foundation. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ */ -+ -+#define pr_fmt(fmt) "%s: " fmt, __func__ -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#include "cpr3-regulator.h" -+ -+#define CPR3_REGULATOR_CORNER_INVALID (-1) -+#define CPR3_RO_MASK GENMASK(CPR3_RO_COUNT - 1, 0) -+ -+/* CPR3 registers */ -+#define CPR3_REG_CPR_CTL 0x4 -+#define CPR3_CPR_CTL_LOOP_EN_MASK BIT(0) -+#define CPR3_CPR_CTL_LOOP_ENABLE BIT(0) -+#define CPR3_CPR_CTL_LOOP_DISABLE 0 -+#define CPR3_CPR_CTL_IDLE_CLOCKS_MASK GENMASK(5, 1) -+#define CPR3_CPR_CTL_IDLE_CLOCKS_SHIFT 1 -+#define CPR3_CPR_CTL_COUNT_MODE_MASK GENMASK(7, 6) -+#define CPR3_CPR_CTL_COUNT_MODE_SHIFT 6 -+#define CPR3_CPR_CTL_COUNT_MODE_ALL_AT_ONCE_MIN 0 -+#define CPR3_CPR_CTL_COUNT_MODE_ALL_AT_ONCE_MAX 1 -+#define CPR3_CPR_CTL_COUNT_MODE_STAGGERED 2 -+#define CPR3_CPR_CTL_COUNT_MODE_ALL_AT_ONCE_AGE 3 -+#define CPR3_CPR_CTL_COUNT_REPEAT_MASK GENMASK(31, 9) -+#define CPR3_CPR_CTL_COUNT_REPEAT_SHIFT 9 -+ -+#define CPR3_REG_CPR_STATUS 0x8 -+#define CPR3_CPR_STATUS_BUSY_MASK BIT(0) -+#define CPR3_CPR_STATUS_AGING_MEASUREMENT_MASK BIT(1) -+ -+/* -+ * This register is not present on controllers that support HW closed-loop -+ * except CPR4 APSS controller. -+ */ -+#define CPR3_REG_CPR_TIMER_AUTO_CONT 0xC -+ -+#define CPR3_REG_CPR_STEP_QUOT 0x14 -+#define CPR3_CPR_STEP_QUOT_MIN_MASK GENMASK(5, 0) -+#define CPR3_CPR_STEP_QUOT_MIN_SHIFT 0 -+#define CPR3_CPR_STEP_QUOT_MAX_MASK GENMASK(11, 6) -+#define CPR3_CPR_STEP_QUOT_MAX_SHIFT 6 -+ -+#define CPR3_REG_GCNT(ro) (0xA0 + 0x4 * (ro)) -+ -+#define CPR3_REG_SENSOR_BYPASS_WRITE(sensor) (0xE0 + 0x4 * ((sensor) / 32)) -+#define CPR3_REG_SENSOR_BYPASS_WRITE_BANK(bank) (0xE0 + 0x4 * (bank)) -+ -+#define CPR3_REG_SENSOR_MASK_WRITE(sensor) (0x120 + 0x4 * ((sensor) / 32)) -+#define CPR3_REG_SENSOR_MASK_WRITE_BANK(bank) (0x120 + 0x4 * (bank)) -+#define CPR3_REG_SENSOR_MASK_READ(sensor) (0x140 + 0x4 * ((sensor) / 32)) -+ -+#define CPR3_REG_SENSOR_OWNER(sensor) (0x200 + 0x4 * (sensor)) -+ -+#define CPR3_REG_CONT_CMD 0x800 -+#define CPR3_CONT_CMD_ACK 0x1 -+#define CPR3_CONT_CMD_NACK 0x0 -+ -+#define CPR3_REG_THRESH(thread) (0x808 + 0x440 * (thread)) -+#define CPR3_THRESH_CONS_DOWN_MASK GENMASK(3, 0) -+#define CPR3_THRESH_CONS_DOWN_SHIFT 0 -+#define CPR3_THRESH_CONS_UP_MASK GENMASK(7, 4) -+#define CPR3_THRESH_CONS_UP_SHIFT 4 -+#define CPR3_THRESH_DOWN_THRESH_MASK GENMASK(12, 8) -+#define CPR3_THRESH_DOWN_THRESH_SHIFT 8 -+#define CPR3_THRESH_UP_THRESH_MASK GENMASK(17, 13) -+#define CPR3_THRESH_UP_THRESH_SHIFT 13 -+ -+#define CPR3_REG_RO_MASK(thread) (0x80C + 0x440 * (thread)) -+ -+#define CPR3_REG_RESULT0(thread) (0x810 + 0x440 * (thread)) -+#define CPR3_RESULT0_BUSY_MASK BIT(0) -+#define CPR3_RESULT0_STEP_DN_MASK BIT(1) -+#define CPR3_RESULT0_STEP_UP_MASK BIT(2) -+#define CPR3_RESULT0_ERROR_STEPS_MASK GENMASK(7, 3) -+#define CPR3_RESULT0_ERROR_STEPS_SHIFT 3 -+#define CPR3_RESULT0_ERROR_MASK GENMASK(19, 8) -+#define CPR3_RESULT0_ERROR_SHIFT 8 -+#define CPR3_RESULT0_NEGATIVE_MASK BIT(20) -+ -+#define CPR3_REG_RESULT1(thread) (0x814 + 0x440 * (thread)) -+#define CPR3_RESULT1_QUOT_MIN_MASK GENMASK(11, 0) -+#define CPR3_RESULT1_QUOT_MIN_SHIFT 0 -+#define CPR3_RESULT1_QUOT_MAX_MASK GENMASK(23, 12) -+#define CPR3_RESULT1_QUOT_MAX_SHIFT 12 -+#define CPR3_RESULT1_RO_MIN_MASK GENMASK(27, 24) -+#define CPR3_RESULT1_RO_MIN_SHIFT 24 -+#define CPR3_RESULT1_RO_MAX_MASK GENMASK(31, 28) -+#define CPR3_RESULT1_RO_MAX_SHIFT 28 -+ -+#define CPR3_REG_RESULT2(thread) (0x818 + 0x440 * (thread)) -+#define CPR3_RESULT2_STEP_QUOT_MIN_MASK GENMASK(5, 0) -+#define CPR3_RESULT2_STEP_QUOT_MIN_SHIFT 0 -+#define CPR3_RESULT2_STEP_QUOT_MAX_MASK GENMASK(11, 6) -+#define CPR3_RESULT2_STEP_QUOT_MAX_SHIFT 6 -+#define CPR3_RESULT2_SENSOR_MIN_MASK GENMASK(23, 16) -+#define CPR3_RESULT2_SENSOR_MIN_SHIFT 16 -+#define CPR3_RESULT2_SENSOR_MAX_MASK GENMASK(31, 24) -+#define CPR3_RESULT2_SENSOR_MAX_SHIFT 24 -+ -+#define CPR3_REG_IRQ_EN 0x81C -+#define CPR3_REG_IRQ_CLEAR 0x820 -+#define CPR3_REG_IRQ_STATUS 0x824 -+#define CPR3_IRQ_UP BIT(3) -+#define CPR3_IRQ_MID BIT(2) -+#define CPR3_IRQ_DOWN BIT(1) -+ -+#define CPR3_REG_TARGET_QUOT(thread, ro) \ -+ (0x840 + 0x440 * (thread) + 0x4 * (ro)) -+ -+/* Registers found only on controllers that support HW closed-loop. */ -+#define CPR3_REG_PD_THROTTLE 0xE8 -+#define CPR3_PD_THROTTLE_DISABLE 0x0 -+ -+#define CPR3_REG_HW_CLOSED_LOOP 0x3000 -+#define CPR3_HW_CLOSED_LOOP_ENABLE 0x0 -+#define CPR3_HW_CLOSED_LOOP_DISABLE 0x1 -+ -+#define CPR3_REG_CPR_TIMER_MID_CONT 0x3004 -+#define CPR3_REG_CPR_TIMER_UP_DN_CONT 0x3008 -+ -+#define CPR3_REG_LAST_MEASUREMENT 0x7F8 -+#define CPR3_LAST_MEASUREMENT_THREAD_DN_SHIFT 0 -+#define CPR3_LAST_MEASUREMENT_THREAD_UP_SHIFT 4 -+#define CPR3_LAST_MEASUREMENT_THREAD_DN(thread) \ -+ (BIT(thread) << CPR3_LAST_MEASUREMENT_THREAD_DN_SHIFT) -+#define CPR3_LAST_MEASUREMENT_THREAD_UP(thread) \ -+ (BIT(thread) << CPR3_LAST_MEASUREMENT_THREAD_UP_SHIFT) -+#define CPR3_LAST_MEASUREMENT_AGGR_DN BIT(8) -+#define CPR3_LAST_MEASUREMENT_AGGR_MID BIT(9) -+#define CPR3_LAST_MEASUREMENT_AGGR_UP BIT(10) -+#define CPR3_LAST_MEASUREMENT_VALID BIT(11) -+#define CPR3_LAST_MEASUREMENT_SAW_ERROR BIT(12) -+#define CPR3_LAST_MEASUREMENT_PD_BYPASS_MASK GENMASK(23, 16) -+#define CPR3_LAST_MEASUREMENT_PD_BYPASS_SHIFT 16 -+ -+/* CPR4 controller specific registers and bit definitions */ -+#define CPR4_REG_CPR_TIMER_CLAMP 0x10 -+#define CPR4_CPR_TIMER_CLAMP_THREAD_AGGREGATION_EN BIT(27) -+ -+#define CPR4_REG_MISC 0x700 -+#define CPR4_MISC_MARGIN_TABLE_ROW_SELECT_MASK GENMASK(23, 20) -+#define CPR4_MISC_MARGIN_TABLE_ROW_SELECT_SHIFT 20 -+#define CPR4_MISC_TEMP_SENSOR_ID_START_MASK GENMASK(27, 24) -+#define CPR4_MISC_TEMP_SENSOR_ID_START_SHIFT 24 -+#define CPR4_MISC_TEMP_SENSOR_ID_END_MASK GENMASK(31, 28) -+#define CPR4_MISC_TEMP_SENSOR_ID_END_SHIFT 28 -+ -+#define CPR4_REG_SAW_ERROR_STEP_LIMIT 0x7A4 -+#define CPR4_SAW_ERROR_STEP_LIMIT_UP_MASK GENMASK(4, 0) -+#define CPR4_SAW_ERROR_STEP_LIMIT_UP_SHIFT 0 -+#define CPR4_SAW_ERROR_STEP_LIMIT_DN_MASK GENMASK(9, 5) -+#define CPR4_SAW_ERROR_STEP_LIMIT_DN_SHIFT 5 -+ -+#define CPR4_REG_MARGIN_TEMP_CORE_TIMERS 0x7A8 -+#define CPR4_MARGIN_TEMP_CORE_TIMERS_SETTLE_VOLTAGE_COUNT_MASK GENMASK(28, 18) -+#define CPR4_MARGIN_TEMP_CORE_TIMERS_SETTLE_VOLTAGE_COUNT_SHIFT 18 -+ -+#define CPR4_REG_MARGIN_TEMP_CORE(core) (0x7AC + 0x4 * (core)) -+#define CPR4_MARGIN_TEMP_CORE_ADJ_MASK GENMASK(7, 0) -+#define CPR4_MARGIN_TEMP_CORE_ADJ_SHIFT 8 -+ -+#define CPR4_REG_MARGIN_TEMP_POINT0N1 0x7F0 -+#define CPR4_MARGIN_TEMP_POINT0_MASK GENMASK(11, 0) -+#define CPR4_MARGIN_TEMP_POINT0_SHIFT 0 -+#define CPR4_MARGIN_TEMP_POINT1_MASK GENMASK(23, 12) -+#define CPR4_MARGIN_TEMP_POINT1_SHIFT 12 -+#define CPR4_REG_MARGIN_TEMP_POINT2 0x7F4 -+#define CPR4_MARGIN_TEMP_POINT2_MASK GENMASK(11, 0) -+#define CPR4_MARGIN_TEMP_POINT2_SHIFT 0 -+ -+#define CPR4_REG_MARGIN_ADJ_CTL 0x7F8 -+#define CPR4_MARGIN_ADJ_CTL_BOOST_EN BIT(0) -+#define CPR4_MARGIN_ADJ_CTL_CORE_ADJ_EN BIT(1) -+#define CPR4_MARGIN_ADJ_CTL_TEMP_ADJ_EN BIT(2) -+#define CPR4_MARGIN_ADJ_CTL_TIMER_SETTLE_VOLTAGE_EN BIT(3) -+#define CPR4_MARGIN_ADJ_CTL_HW_CLOSED_LOOP_EN_MASK BIT(4) -+#define CPR4_MARGIN_ADJ_CTL_HW_CLOSED_LOOP_ENABLE BIT(4) -+#define CPR4_MARGIN_ADJ_CTL_HW_CLOSED_LOOP_DISABLE 0 -+#define CPR4_MARGIN_ADJ_CTL_PER_RO_KV_MARGIN_EN BIT(7) -+#define CPR4_MARGIN_ADJ_CTL_KV_MARGIN_ADJ_EN BIT(8) -+#define CPR4_MARGIN_ADJ_CTL_PMIC_STEP_SIZE_MASK GENMASK(16, 12) -+#define CPR4_MARGIN_ADJ_CTL_PMIC_STEP_SIZE_SHIFT 12 -+#define CPR4_MARGIN_ADJ_CTL_INITIAL_TEMP_BAND_MASK GENMASK(21, 19) -+#define CPR4_MARGIN_ADJ_CTL_INITIAL_TEMP_BAND_SHIFT 19 -+#define CPR4_MARGIN_ADJ_CTL_MAX_NUM_CORES_MASK GENMASK(25, 22) -+#define CPR4_MARGIN_ADJ_CTL_MAX_NUM_CORES_SHIFT 22 -+#define CPR4_MARGIN_ADJ_CTL_KV_MARGIN_ADJ_STEP_QUOT_MASK GENMASK(31, 26) -+#define CPR4_MARGIN_ADJ_CTL_KV_MARGIN_ADJ_STEP_QUOT_SHIFT 26 -+ -+#define CPR4_REG_CPR_MASK_THREAD(thread) (0x80C + 0x440 * (thread)) -+#define CPR4_CPR_MASK_THREAD_DISABLE_THREAD BIT(31) -+#define CPR4_CPR_MASK_THREAD_RO_MASK4THREAD_MASK GENMASK(15, 0) -+ -+/* -+ * The amount of time to wait for the CPR controller to become idle when -+ * performing an aging measurement. -+ */ -+#define CPR3_AGING_MEASUREMENT_TIMEOUT_NS 5000000 -+ -+/* -+ * The number of individual aging measurements to perform which are then -+ * averaged together in order to determine the final aging adjustment value. -+ */ -+#define CPR3_AGING_MEASUREMENT_ITERATIONS 16 -+ -+/* -+ * Aging measurements for the aged and unaged ring oscillators take place a few -+ * microseconds apart. If the vdd-supply voltage fluctuates between the two -+ * measurements, then the difference between them will be incorrect. The -+ * difference could end up too high or too low. This constant defines the -+ * number of lowest and highest measurements to ignore when averaging. -+ */ -+#define CPR3_AGING_MEASUREMENT_FILTER 3 -+ -+/* -+ * The number of times to attempt the full aging measurement sequence before -+ * declaring a measurement failure. -+ */ -+#define CPR3_AGING_RETRY_COUNT 5 -+ -+/* -+ * The maximum time to wait in microseconds for a CPR register write to -+ * complete. -+ */ -+#define CPR3_REGISTER_WRITE_DELAY_US 200 -+ -+static DEFINE_MUTEX(cpr3_controller_list_mutex); -+static LIST_HEAD(cpr3_controller_list); -+static struct dentry *cpr3_debugfs_base; -+ -+/** -+ * cpr3_read() - read four bytes from the memory address specified -+ * @ctrl: Pointer to the CPR3 controller -+ * @offset: Offset in bytes from the CPR3 controller's base address -+ * -+ * Return: memory address value -+ */ -+static inline u32 cpr3_read(struct cpr3_controller *ctrl, u32 offset) -+{ -+ if (!ctrl->cpr_enabled) { -+ cpr3_err(ctrl, "CPR register reads are not possible when CPR clocks are disabled\n"); -+ return 0; -+ } -+ -+ return readl_relaxed(ctrl->cpr_ctrl_base + offset); -+} -+ -+/** -+ * cpr3_write() - write four bytes to the memory address specified -+ * @ctrl: Pointer to the CPR3 controller -+ * @offset: Offset in bytes from the CPR3 controller's base address -+ * @value: Value to write to the memory address -+ * -+ * Return: none -+ */ -+static inline void cpr3_write(struct cpr3_controller *ctrl, u32 offset, -+ u32 value) -+{ -+ if (!ctrl->cpr_enabled) { -+ cpr3_err(ctrl, "CPR register writes are not possible when CPR clocks are disabled\n"); -+ return; -+ } -+ -+ writel_relaxed(value, ctrl->cpr_ctrl_base + offset); -+} -+ -+/** -+ * cpr3_masked_write() - perform a read-modify-write sequence so that only -+ * masked bits are modified -+ * @ctrl: Pointer to the CPR3 controller -+ * @offset: Offset in bytes from the CPR3 controller's base address -+ * @mask: Mask identifying the bits that should be modified -+ * @value: Value to write to the memory address -+ * -+ * Return: none -+ */ -+static inline void cpr3_masked_write(struct cpr3_controller *ctrl, u32 offset, -+ u32 mask, u32 value) -+{ -+ u32 reg_val, orig_val; -+ -+ if (!ctrl->cpr_enabled) { -+ cpr3_err(ctrl, "CPR register writes are not possible when CPR clocks are disabled\n"); -+ return; -+ } -+ -+ reg_val = orig_val = readl_relaxed(ctrl->cpr_ctrl_base + offset); -+ reg_val &= ~mask; -+ reg_val |= value & mask; -+ -+ if (reg_val != orig_val) -+ writel_relaxed(reg_val, ctrl->cpr_ctrl_base + offset); -+} -+ -+/** -+ * cpr3_ctrl_loop_enable() - enable the CPR sensing loop for a given controller -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: none -+ */ -+static inline void cpr3_ctrl_loop_enable(struct cpr3_controller *ctrl) -+{ -+ if (ctrl->cpr_enabled && !(ctrl->aggr_corner.sdelta -+ && ctrl->aggr_corner.sdelta->allow_boost)) -+ cpr3_masked_write(ctrl, CPR3_REG_CPR_CTL, -+ CPR3_CPR_CTL_LOOP_EN_MASK, CPR3_CPR_CTL_LOOP_ENABLE); -+} -+ -+/** -+ * cpr3_ctrl_loop_disable() - disable the CPR sensing loop for a given -+ * controller -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: none -+ */ -+static inline void cpr3_ctrl_loop_disable(struct cpr3_controller *ctrl) -+{ -+ if (ctrl->cpr_enabled) -+ cpr3_masked_write(ctrl, CPR3_REG_CPR_CTL, -+ CPR3_CPR_CTL_LOOP_EN_MASK, CPR3_CPR_CTL_LOOP_DISABLE); -+} -+ -+/** -+ * cpr3_clock_enable() - prepare and enable all clocks used by this CPR3 -+ * controller -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_clock_enable(struct cpr3_controller *ctrl) -+{ -+ int rc; -+ -+ rc = clk_prepare_enable(ctrl->bus_clk); -+ if (rc) { -+ cpr3_err(ctrl, "failed to enable bus clock, rc=%d\n", rc); -+ return rc; -+ } -+ -+ rc = clk_prepare_enable(ctrl->iface_clk); -+ if (rc) { -+ cpr3_err(ctrl, "failed to enable interface clock, rc=%d\n", rc); -+ clk_disable_unprepare(ctrl->bus_clk); -+ return rc; -+ } -+ -+ rc = clk_prepare_enable(ctrl->core_clk); -+ if (rc) { -+ cpr3_err(ctrl, "failed to enable core clock, rc=%d\n", rc); -+ clk_disable_unprepare(ctrl->iface_clk); -+ clk_disable_unprepare(ctrl->bus_clk); -+ return rc; -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr3_clock_disable() - disable and unprepare all clocks used by this CPR3 -+ * controller -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: none -+ */ -+static void cpr3_clock_disable(struct cpr3_controller *ctrl) -+{ -+ clk_disable_unprepare(ctrl->core_clk); -+ clk_disable_unprepare(ctrl->iface_clk); -+ clk_disable_unprepare(ctrl->bus_clk); -+} -+ -+/** -+ * cpr3_ctrl_clear_cpr4_config() - clear the CPR4 register configuration -+ * programmed for current aggregated corner of a given controller -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static inline int cpr3_ctrl_clear_cpr4_config(struct cpr3_controller *ctrl) -+{ -+ struct cpr4_sdelta *aggr_sdelta = ctrl->aggr_corner.sdelta; -+ bool cpr_enabled = ctrl->cpr_enabled; -+ int i, rc = 0; -+ -+ if (!aggr_sdelta || !(aggr_sdelta->allow_core_count_adj -+ || aggr_sdelta->allow_temp_adj || aggr_sdelta->allow_boost)) -+ /* cpr4 features are not enabled */ -+ return 0; -+ -+ /* Ensure that CPR clocks are enabled before writing to registers. */ -+ if (!cpr_enabled) { -+ rc = cpr3_clock_enable(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "clock enable failed, rc=%d\n", rc); -+ return rc; -+ } -+ ctrl->cpr_enabled = true; -+ } -+ -+ /* -+ * Clear feature enable configuration made for current -+ * aggregated corner. -+ */ -+ cpr3_masked_write(ctrl, CPR4_REG_MARGIN_ADJ_CTL, -+ CPR4_MARGIN_ADJ_CTL_MAX_NUM_CORES_MASK -+ | CPR4_MARGIN_ADJ_CTL_CORE_ADJ_EN -+ | CPR4_MARGIN_ADJ_CTL_TEMP_ADJ_EN -+ | CPR4_MARGIN_ADJ_CTL_KV_MARGIN_ADJ_EN -+ | CPR4_MARGIN_ADJ_CTL_BOOST_EN -+ | CPR4_MARGIN_ADJ_CTL_HW_CLOSED_LOOP_EN_MASK, 0); -+ -+ cpr3_masked_write(ctrl, CPR4_REG_MISC, -+ CPR4_MISC_MARGIN_TABLE_ROW_SELECT_MASK, -+ 0 << CPR4_MISC_MARGIN_TABLE_ROW_SELECT_SHIFT); -+ -+ for (i = 0; i <= aggr_sdelta->max_core_count; i++) { -+ /* Clear voltage margin adjustments programmed in TEMP_COREi */ -+ cpr3_write(ctrl, CPR4_REG_MARGIN_TEMP_CORE(i), 0); -+ } -+ -+ /* Turn off CPR clocks if they were off before this function call. */ -+ if (!cpr_enabled) { -+ cpr3_clock_disable(ctrl); -+ ctrl->cpr_enabled = false; -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr3_closed_loop_enable() - enable logical CPR closed-loop operation -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_closed_loop_enable(struct cpr3_controller *ctrl) -+{ -+ int rc; -+ -+ if (!ctrl->cpr_allowed_hw || !ctrl->cpr_allowed_sw) { -+ cpr3_err(ctrl, "cannot enable closed-loop CPR operation because it is disallowed\n"); -+ return -EPERM; -+ } else if (ctrl->cpr_enabled) { -+ /* Already enabled */ -+ return 0; -+ } else if (ctrl->cpr_suspended) { -+ /* -+ * CPR must remain disabled as the system is entering suspend. -+ */ -+ return 0; -+ } -+ -+ rc = cpr3_clock_enable(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "unable to enable CPR clocks, rc=%d\n", rc); -+ return rc; -+ } -+ -+ ctrl->cpr_enabled = true; -+ cpr3_debug(ctrl, "CPR closed-loop operation enabled\n"); -+ -+ return 0; -+} -+ -+/** -+ * cpr3_closed_loop_disable() - disable logical CPR closed-loop operation -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static inline int cpr3_closed_loop_disable(struct cpr3_controller *ctrl) -+{ -+ if (!ctrl->cpr_enabled) { -+ /* Already disabled */ -+ return 0; -+ } -+ -+ cpr3_clock_disable(ctrl); -+ ctrl->cpr_enabled = false; -+ cpr3_debug(ctrl, "CPR closed-loop operation disabled\n"); -+ -+ return 0; -+} -+ -+/** -+ * cpr3_regulator_get_gcnt() - returns the GCNT register value corresponding -+ * to the clock rate and sensor time of the CPR3 controller -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: GCNT value -+ */ -+static u32 cpr3_regulator_get_gcnt(struct cpr3_controller *ctrl) -+{ -+ u64 temp; -+ unsigned int remainder; -+ u32 gcnt; -+ -+ temp = (u64)ctrl->cpr_clock_rate * (u64)ctrl->sensor_time; -+ remainder = do_div(temp, 1000000000); -+ if (remainder) -+ temp++; -+ /* -+ * GCNT == 0 corresponds to a single ref clock measurement interval so -+ * offset GCNT values by 1. -+ */ -+ gcnt = temp - 1; -+ -+ return gcnt; -+} -+ -+/** -+ * cpr3_regulator_init_thread() - performs hardware initialization of CPR -+ * thread registers -+ * @thread: Pointer to the CPR3 thread -+ * -+ * CPR interface/bus clocks must be enabled before calling this function. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_regulator_init_thread(struct cpr3_thread *thread) -+{ -+ u32 reg; -+ -+ reg = (thread->consecutive_up << CPR3_THRESH_CONS_UP_SHIFT) -+ & CPR3_THRESH_CONS_UP_MASK; -+ reg |= (thread->consecutive_down << CPR3_THRESH_CONS_DOWN_SHIFT) -+ & CPR3_THRESH_CONS_DOWN_MASK; -+ reg |= (thread->up_threshold << CPR3_THRESH_UP_THRESH_SHIFT) -+ & CPR3_THRESH_UP_THRESH_MASK; -+ reg |= (thread->down_threshold << CPR3_THRESH_DOWN_THRESH_SHIFT) -+ & CPR3_THRESH_DOWN_THRESH_MASK; -+ -+ cpr3_write(thread->ctrl, CPR3_REG_THRESH(thread->thread_id), reg); -+ -+ /* -+ * Mask all RO's initially so that unused thread doesn't contribute -+ * to closed-loop voltage. -+ */ -+ cpr3_write(thread->ctrl, CPR3_REG_RO_MASK(thread->thread_id), -+ CPR3_RO_MASK); -+ -+ return 0; -+} -+ -+/** -+ * cpr4_regulator_init_temp_points() - performs hardware initialization of CPR4 -+ * registers to track tsen temperature data and also specify the -+ * temperature band range values to apply different voltage margins -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * CPR interface/bus clocks must be enabled before calling this function. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr4_regulator_init_temp_points(struct cpr3_controller *ctrl) -+{ -+ if (!ctrl->allow_temp_adj) -+ return 0; -+ -+ cpr3_masked_write(ctrl, CPR4_REG_MISC, -+ CPR4_MISC_TEMP_SENSOR_ID_START_MASK, -+ ctrl->temp_sensor_id_start -+ << CPR4_MISC_TEMP_SENSOR_ID_START_SHIFT); -+ -+ cpr3_masked_write(ctrl, CPR4_REG_MISC, -+ CPR4_MISC_TEMP_SENSOR_ID_END_MASK, -+ ctrl->temp_sensor_id_end -+ << CPR4_MISC_TEMP_SENSOR_ID_END_SHIFT); -+ -+ cpr3_masked_write(ctrl, CPR4_REG_MARGIN_TEMP_POINT2, -+ CPR4_MARGIN_TEMP_POINT2_MASK, -+ (ctrl->temp_band_count == 4 ? ctrl->temp_points[2] : 0x7FF) -+ << CPR4_MARGIN_TEMP_POINT2_SHIFT); -+ -+ cpr3_masked_write(ctrl, CPR4_REG_MARGIN_TEMP_POINT0N1, -+ CPR4_MARGIN_TEMP_POINT1_MASK, -+ (ctrl->temp_band_count >= 3 ? ctrl->temp_points[1] : 0x7FF) -+ << CPR4_MARGIN_TEMP_POINT1_SHIFT); -+ -+ cpr3_masked_write(ctrl, CPR4_REG_MARGIN_TEMP_POINT0N1, -+ CPR4_MARGIN_TEMP_POINT0_MASK, -+ (ctrl->temp_band_count >= 2 ? ctrl->temp_points[0] : 0x7FF) -+ << CPR4_MARGIN_TEMP_POINT0_SHIFT); -+ return 0; -+} -+ -+/** -+ * cpr3_regulator_init_cpr4() - performs hardware initialization at the -+ * controller and thread level required for CPR4 operation. -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * CPR interface/bus clocks must be enabled before calling this function. -+ * This function allocates sdelta structures and sdelta tables for aggregated -+ * corners of the controller and its threads. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_regulator_init_cpr4(struct cpr3_controller *ctrl) -+{ -+ struct cpr3_thread *thread; -+ struct cpr3_regulator *vreg; -+ struct cpr4_sdelta *sdelta; -+ int i, j, ctrl_max_core_count, thread_max_core_count, rc = 0; -+ bool ctrl_valid_sdelta, thread_valid_sdelta; -+ u32 pmic_step_size = 1; -+ int thread_id = 0; -+ u64 temp; -+ -+ if (ctrl->supports_hw_closed_loop) { -+ if (ctrl->saw_use_unit_mV) -+ pmic_step_size = ctrl->step_volt / 1000; -+ cpr3_masked_write(ctrl, CPR4_REG_MARGIN_ADJ_CTL, -+ CPR4_MARGIN_ADJ_CTL_PMIC_STEP_SIZE_MASK, -+ (pmic_step_size -+ << CPR4_MARGIN_ADJ_CTL_PMIC_STEP_SIZE_SHIFT)); -+ -+ cpr3_masked_write(ctrl, CPR4_REG_SAW_ERROR_STEP_LIMIT, -+ CPR4_SAW_ERROR_STEP_LIMIT_DN_MASK, -+ (ctrl->down_error_step_limit -+ << CPR4_SAW_ERROR_STEP_LIMIT_DN_SHIFT)); -+ -+ cpr3_masked_write(ctrl, CPR4_REG_SAW_ERROR_STEP_LIMIT, -+ CPR4_SAW_ERROR_STEP_LIMIT_UP_MASK, -+ (ctrl->up_error_step_limit -+ << CPR4_SAW_ERROR_STEP_LIMIT_UP_SHIFT)); -+ -+ /* -+ * Enable thread aggregation regardless of which threads are -+ * enabled or disabled. -+ */ -+ cpr3_masked_write(ctrl, CPR4_REG_CPR_TIMER_CLAMP, -+ CPR4_CPR_TIMER_CLAMP_THREAD_AGGREGATION_EN, -+ CPR4_CPR_TIMER_CLAMP_THREAD_AGGREGATION_EN); -+ -+ switch (ctrl->thread_count) { -+ case 0: -+ /* Disable both threads */ -+ cpr3_masked_write(ctrl, CPR4_REG_CPR_MASK_THREAD(0), -+ CPR4_CPR_MASK_THREAD_DISABLE_THREAD -+ | CPR4_CPR_MASK_THREAD_RO_MASK4THREAD_MASK, -+ CPR4_CPR_MASK_THREAD_DISABLE_THREAD -+ | CPR4_CPR_MASK_THREAD_RO_MASK4THREAD_MASK); -+ -+ cpr3_masked_write(ctrl, CPR4_REG_CPR_MASK_THREAD(1), -+ CPR4_CPR_MASK_THREAD_DISABLE_THREAD -+ | CPR4_CPR_MASK_THREAD_RO_MASK4THREAD_MASK, -+ CPR4_CPR_MASK_THREAD_DISABLE_THREAD -+ | CPR4_CPR_MASK_THREAD_RO_MASK4THREAD_MASK); -+ break; -+ case 1: -+ /* Disable unused thread */ -+ thread_id = ctrl->thread[0].thread_id ? 0 : 1; -+ cpr3_masked_write(ctrl, -+ CPR4_REG_CPR_MASK_THREAD(thread_id), -+ CPR4_CPR_MASK_THREAD_DISABLE_THREAD -+ | CPR4_CPR_MASK_THREAD_RO_MASK4THREAD_MASK, -+ CPR4_CPR_MASK_THREAD_DISABLE_THREAD -+ | CPR4_CPR_MASK_THREAD_RO_MASK4THREAD_MASK); -+ break; -+ } -+ } -+ -+ if (!ctrl->allow_core_count_adj && !ctrl->allow_temp_adj -+ && !ctrl->allow_boost) { -+ /* -+ * Skip below configuration as none of the features -+ * are enabled. -+ */ -+ return rc; -+ } -+ -+ if (ctrl->supports_hw_closed_loop) -+ cpr3_masked_write(ctrl, CPR4_REG_MARGIN_ADJ_CTL, -+ CPR4_MARGIN_ADJ_CTL_TIMER_SETTLE_VOLTAGE_EN, -+ CPR4_MARGIN_ADJ_CTL_TIMER_SETTLE_VOLTAGE_EN); -+ -+ cpr3_masked_write(ctrl, CPR4_REG_MARGIN_ADJ_CTL, -+ CPR4_MARGIN_ADJ_CTL_KV_MARGIN_ADJ_STEP_QUOT_MASK, -+ ctrl->step_quot_fixed -+ << CPR4_MARGIN_ADJ_CTL_KV_MARGIN_ADJ_STEP_QUOT_SHIFT); -+ -+ cpr3_masked_write(ctrl, CPR4_REG_MARGIN_ADJ_CTL, -+ CPR4_MARGIN_ADJ_CTL_PER_RO_KV_MARGIN_EN, -+ (ctrl->use_dynamic_step_quot -+ ? CPR4_MARGIN_ADJ_CTL_PER_RO_KV_MARGIN_EN : 0)); -+ -+ cpr3_masked_write(ctrl, CPR4_REG_MARGIN_ADJ_CTL, -+ CPR4_MARGIN_ADJ_CTL_INITIAL_TEMP_BAND_MASK, -+ ctrl->initial_temp_band -+ << CPR4_MARGIN_ADJ_CTL_INITIAL_TEMP_BAND_SHIFT); -+ -+ rc = cpr4_regulator_init_temp_points(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "initialize temp points failed, rc=%d\n", rc); -+ return rc; -+ } -+ -+ if (ctrl->voltage_settling_time) { -+ /* -+ * Configure the settling timer used to account for -+ * one VDD supply step. -+ */ -+ temp = (u64)ctrl->cpr_clock_rate -+ * (u64)ctrl->voltage_settling_time; -+ do_div(temp, 1000000000); -+ cpr3_masked_write(ctrl, CPR4_REG_MARGIN_TEMP_CORE_TIMERS, -+ CPR4_MARGIN_TEMP_CORE_TIMERS_SETTLE_VOLTAGE_COUNT_MASK, -+ temp -+ << CPR4_MARGIN_TEMP_CORE_TIMERS_SETTLE_VOLTAGE_COUNT_SHIFT); -+ } -+ -+ /* -+ * Allocate memory for cpr4_sdelta structure and sdelta table for -+ * controller aggregated corner by finding the maximum core count -+ * used by any cpr3 regulators. -+ */ -+ ctrl_max_core_count = 1; -+ ctrl_valid_sdelta = false; -+ for (i = 0; i < ctrl->thread_count; i++) { -+ thread = &ctrl->thread[i]; -+ -+ /* -+ * Allocate memory for cpr4_sdelta structure and sdelta table -+ * for thread aggregated corner by finding the maximum core -+ * count used by any cpr3 regulators of the thread. -+ */ -+ thread_max_core_count = 1; -+ thread_valid_sdelta = false; -+ for (j = 0; j < thread->vreg_count; j++) { -+ vreg = &thread->vreg[j]; -+ thread_max_core_count = max(thread_max_core_count, -+ vreg->max_core_count); -+ thread_valid_sdelta |= (vreg->allow_core_count_adj -+ | vreg->allow_temp_adj -+ | vreg->allow_boost); -+ } -+ if (thread_valid_sdelta) { -+ sdelta = devm_kzalloc(ctrl->dev, sizeof(*sdelta), -+ GFP_KERNEL); -+ if (!sdelta) -+ return -ENOMEM; -+ -+ sdelta->table = devm_kcalloc(ctrl->dev, -+ thread_max_core_count -+ * ctrl->temp_band_count, -+ sizeof(*sdelta->table), -+ GFP_KERNEL); -+ if (!sdelta->table) -+ return -ENOMEM; -+ -+ sdelta->boost_table = devm_kcalloc(ctrl->dev, -+ ctrl->temp_band_count, -+ sizeof(*sdelta->boost_table), -+ GFP_KERNEL); -+ if (!sdelta->boost_table) -+ return -ENOMEM; -+ -+ thread->aggr_corner.sdelta = sdelta; -+ } -+ -+ ctrl_valid_sdelta |= thread_valid_sdelta; -+ ctrl_max_core_count = max(ctrl_max_core_count, -+ thread_max_core_count); -+ } -+ -+ if (ctrl_valid_sdelta) { -+ sdelta = devm_kzalloc(ctrl->dev, sizeof(*sdelta), GFP_KERNEL); -+ if (!sdelta) -+ return -ENOMEM; -+ -+ sdelta->table = devm_kcalloc(ctrl->dev, ctrl_max_core_count -+ * ctrl->temp_band_count, -+ sizeof(*sdelta->table), GFP_KERNEL); -+ if (!sdelta->table) -+ return -ENOMEM; -+ -+ sdelta->boost_table = devm_kcalloc(ctrl->dev, -+ ctrl->temp_band_count, -+ sizeof(*sdelta->boost_table), -+ GFP_KERNEL); -+ if (!sdelta->boost_table) -+ return -ENOMEM; -+ -+ ctrl->aggr_corner.sdelta = sdelta; -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr3_write_temp_core_margin() - programs hardware SDELTA registers with -+ * the voltage margin adjustments that need to be applied for -+ * different online core-count and temperature bands. -+ * @ctrl: Pointer to the CPR3 controller -+ * @addr: SDELTA register address -+ * @temp_core_adj: Array of voltage margin values for different temperature -+ * bands. -+ * -+ * CPR interface/bus clocks must be enabled before calling this function. -+ * -+ * Return: none -+ */ -+static void cpr3_write_temp_core_margin(struct cpr3_controller *ctrl, -+ int addr, int *temp_core_adj) -+{ -+ int i, margin_steps; -+ u32 reg = 0; -+ -+ for (i = 0; i < ctrl->temp_band_count; i++) { -+ margin_steps = max(min(temp_core_adj[i], 127), -128); -+ reg |= (margin_steps & CPR4_MARGIN_TEMP_CORE_ADJ_MASK) << -+ (i * CPR4_MARGIN_TEMP_CORE_ADJ_SHIFT); -+ } -+ -+ cpr3_write(ctrl, addr, reg); -+ cpr3_debug(ctrl, "sdelta offset=0x%08x, val=0x%08x\n", addr, reg); -+} -+ -+/** -+ * cpr3_controller_program_sdelta() - programs hardware SDELTA registers with -+ * the voltage margin adjustments that need to be applied at -+ * different online core-count and temperature bands. Also, -+ * programs hardware register configuration for per-online-core -+ * and per-temperature based adjustments. -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * CPR interface/bus clocks must be enabled before calling this function. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_controller_program_sdelta(struct cpr3_controller *ctrl) -+{ -+ struct cpr3_corner *corner = &ctrl->aggr_corner; -+ struct cpr4_sdelta *sdelta = corner->sdelta; -+ int i, index, max_core_count, rc = 0; -+ bool cpr_enabled = ctrl->cpr_enabled; -+ -+ if (!sdelta) -+ /* cpr4_sdelta not defined for current aggregated corner */ -+ return 0; -+ -+ if (ctrl->supports_hw_closed_loop && ctrl->cpr_enabled) { -+ cpr3_masked_write(ctrl, CPR4_REG_MARGIN_ADJ_CTL, -+ CPR4_MARGIN_ADJ_CTL_HW_CLOSED_LOOP_EN_MASK, -+ (ctrl->use_hw_closed_loop && !sdelta->allow_boost) -+ ? CPR4_MARGIN_ADJ_CTL_HW_CLOSED_LOOP_ENABLE : 0); -+ } -+ -+ if (!sdelta->allow_core_count_adj && !sdelta->allow_temp_adj -+ && !sdelta->allow_boost) { -+ /* -+ * Per-online-core, per-temperature and voltage boost -+ * adjustments are disabled for this aggregation corner. -+ */ -+ return 0; -+ } -+ -+ /* Ensure that CPR clocks are enabled before writing to registers. */ -+ if (!cpr_enabled) { -+ rc = cpr3_clock_enable(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "clock enable failed, rc=%d\n", rc); -+ return rc; -+ } -+ ctrl->cpr_enabled = true; -+ } -+ -+ max_core_count = sdelta->max_core_count; -+ -+ if (sdelta->allow_core_count_adj || sdelta->allow_temp_adj) { -+ if (sdelta->allow_core_count_adj) { -+ /* Program TEMP_CORE0 to same margins as TEMP_CORE1 */ -+ cpr3_write_temp_core_margin(ctrl, -+ CPR4_REG_MARGIN_TEMP_CORE(0), -+ &sdelta->table[0]); -+ } -+ -+ for (i = 0; i < max_core_count; i++) { -+ index = i * sdelta->temp_band_count; -+ /* -+ * Program TEMP_COREi with voltage margin adjustments -+ * that need to be applied when the number of cores -+ * becomes i. -+ */ -+ cpr3_write_temp_core_margin(ctrl, -+ CPR4_REG_MARGIN_TEMP_CORE( -+ sdelta->allow_core_count_adj -+ ? i + 1 : max_core_count), -+ &sdelta->table[index]); -+ } -+ } -+ -+ if (sdelta->allow_boost) { -+ /* Program only boost_num_cores row of SDELTA */ -+ cpr3_write_temp_core_margin(ctrl, -+ CPR4_REG_MARGIN_TEMP_CORE(sdelta->boost_num_cores), -+ &sdelta->boost_table[0]); -+ } -+ -+ if (!sdelta->allow_core_count_adj && !sdelta->allow_boost) { -+ cpr3_masked_write(ctrl, CPR4_REG_MISC, -+ CPR4_MISC_MARGIN_TABLE_ROW_SELECT_MASK, -+ max_core_count -+ << CPR4_MISC_MARGIN_TABLE_ROW_SELECT_SHIFT); -+ } -+ -+ cpr3_masked_write(ctrl, CPR4_REG_MARGIN_ADJ_CTL, -+ CPR4_MARGIN_ADJ_CTL_MAX_NUM_CORES_MASK -+ | CPR4_MARGIN_ADJ_CTL_CORE_ADJ_EN -+ | CPR4_MARGIN_ADJ_CTL_TEMP_ADJ_EN -+ | CPR4_MARGIN_ADJ_CTL_KV_MARGIN_ADJ_EN -+ | CPR4_MARGIN_ADJ_CTL_BOOST_EN, -+ max_core_count << CPR4_MARGIN_ADJ_CTL_MAX_NUM_CORES_SHIFT -+ | ((sdelta->allow_core_count_adj || sdelta->allow_boost) -+ ? CPR4_MARGIN_ADJ_CTL_CORE_ADJ_EN : 0) -+ | ((sdelta->allow_temp_adj && ctrl->supports_hw_closed_loop) -+ ? CPR4_MARGIN_ADJ_CTL_TEMP_ADJ_EN : 0) -+ | (((ctrl->use_hw_closed_loop && !sdelta->allow_boost) -+ || !ctrl->supports_hw_closed_loop) -+ ? CPR4_MARGIN_ADJ_CTL_KV_MARGIN_ADJ_EN : 0) -+ | (sdelta->allow_boost -+ ? CPR4_MARGIN_ADJ_CTL_BOOST_EN : 0)); -+ -+ /* -+ * Ensure that all previous CPR register writes have completed before -+ * continuing. -+ */ -+ mb(); -+ -+ /* Turn off CPR clocks if they were off before this function call. */ -+ if (!cpr_enabled) { -+ cpr3_clock_disable(ctrl); -+ ctrl->cpr_enabled = false; -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr3_regulator_init_ctrl() - performs hardware initialization of CPR -+ * controller registers -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_regulator_init_ctrl(struct cpr3_controller *ctrl) -+{ -+ int i, j, k, m, rc; -+ u32 ro_used = 0; -+ u32 gcnt, cont_dly, up_down_dly, val; -+ u64 temp; -+ char *mode; -+ -+ if (ctrl->core_clk) { -+ rc = clk_set_rate(ctrl->core_clk, ctrl->cpr_clock_rate); -+ if (rc) { -+ cpr3_err(ctrl, "clk_set_rate(core_clk, %u) failed, rc=%d\n", -+ ctrl->cpr_clock_rate, rc); -+ return rc; -+ } -+ } -+ -+ rc = cpr3_clock_enable(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "clock enable failed, rc=%d\n", rc); -+ return rc; -+ } -+ ctrl->cpr_enabled = true; -+ -+ /* Find all RO's used by any corner of any regulator. */ -+ for (i = 0; i < ctrl->thread_count; i++) -+ for (j = 0; j < ctrl->thread[i].vreg_count; j++) -+ for (k = 0; k < ctrl->thread[i].vreg[j].corner_count; -+ k++) -+ for (m = 0; m < CPR3_RO_COUNT; m++) -+ if (ctrl->thread[i].vreg[j].corner[k]. -+ target_quot[m]) -+ ro_used |= BIT(m); -+ -+ /* Configure the GCNT of the RO's that will be used */ -+ gcnt = cpr3_regulator_get_gcnt(ctrl); -+ for (i = 0; i < CPR3_RO_COUNT; i++) -+ if (ro_used & BIT(i)) -+ cpr3_write(ctrl, CPR3_REG_GCNT(i), gcnt); -+ -+ /* Configure the loop delay time */ -+ temp = (u64)ctrl->cpr_clock_rate * (u64)ctrl->loop_time; -+ do_div(temp, 1000000000); -+ cont_dly = temp; -+ if (ctrl->supports_hw_closed_loop -+ && ctrl->ctrl_type == CPR_CTRL_TYPE_CPR3) -+ cpr3_write(ctrl, CPR3_REG_CPR_TIMER_MID_CONT, cont_dly); -+ else -+ cpr3_write(ctrl, CPR3_REG_CPR_TIMER_AUTO_CONT, cont_dly); -+ -+ if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR3) { -+ temp = (u64)ctrl->cpr_clock_rate * -+ (u64)ctrl->up_down_delay_time; -+ do_div(temp, 1000000000); -+ up_down_dly = temp; -+ if (ctrl->supports_hw_closed_loop) -+ cpr3_write(ctrl, CPR3_REG_CPR_TIMER_UP_DN_CONT, -+ up_down_dly); -+ cpr3_debug(ctrl, "up_down_dly=%u, up_down_delay_time=%u ns\n", -+ up_down_dly, ctrl->up_down_delay_time); -+ } -+ -+ cpr3_debug(ctrl, "cpr_clock_rate=%u HZ, sensor_time=%u ns, loop_time=%u ns, gcnt=%u, cont_dly=%u\n", -+ ctrl->cpr_clock_rate, ctrl->sensor_time, ctrl->loop_time, -+ gcnt, cont_dly); -+ -+ /* Configure CPR sensor operation */ -+ val = (ctrl->idle_clocks << CPR3_CPR_CTL_IDLE_CLOCKS_SHIFT) -+ & CPR3_CPR_CTL_IDLE_CLOCKS_MASK; -+ val |= (ctrl->count_mode << CPR3_CPR_CTL_COUNT_MODE_SHIFT) -+ & CPR3_CPR_CTL_COUNT_MODE_MASK; -+ val |= (ctrl->count_repeat << CPR3_CPR_CTL_COUNT_REPEAT_SHIFT) -+ & CPR3_CPR_CTL_COUNT_REPEAT_MASK; -+ cpr3_write(ctrl, CPR3_REG_CPR_CTL, val); -+ -+ cpr3_debug(ctrl, "idle_clocks=%u, count_mode=%u, count_repeat=%u; CPR_CTL=0x%08X\n", -+ ctrl->idle_clocks, ctrl->count_mode, ctrl->count_repeat, val); -+ -+ /* Configure CPR default step quotients */ -+ val = (ctrl->step_quot_init_min << CPR3_CPR_STEP_QUOT_MIN_SHIFT) -+ & CPR3_CPR_STEP_QUOT_MIN_MASK; -+ val |= (ctrl->step_quot_init_max << CPR3_CPR_STEP_QUOT_MAX_SHIFT) -+ & CPR3_CPR_STEP_QUOT_MAX_MASK; -+ cpr3_write(ctrl, CPR3_REG_CPR_STEP_QUOT, val); -+ -+ cpr3_debug(ctrl, "step_quot_min=%u, step_quot_max=%u; STEP_QUOT=0x%08X\n", -+ ctrl->step_quot_init_min, ctrl->step_quot_init_max, val); -+ -+ /* Configure the CPR sensor ownership */ -+ for (i = 0; i < ctrl->sensor_count; i++) -+ cpr3_write(ctrl, CPR3_REG_SENSOR_OWNER(i), -+ ctrl->sensor_owner[i]); -+ -+ /* Configure per-thread registers */ -+ for (i = 0; i < ctrl->thread_count; i++) { -+ rc = cpr3_regulator_init_thread(&ctrl->thread[i]); -+ if (rc) { -+ cpr3_err(ctrl, "CPR thread register initialization failed, rc=%d\n", -+ rc); -+ return rc; -+ } -+ } -+ -+ if (ctrl->supports_hw_closed_loop) { -+ if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR4) { -+ cpr3_masked_write(ctrl, CPR4_REG_MARGIN_ADJ_CTL, -+ CPR4_MARGIN_ADJ_CTL_HW_CLOSED_LOOP_EN_MASK, -+ ctrl->use_hw_closed_loop -+ ? CPR4_MARGIN_ADJ_CTL_HW_CLOSED_LOOP_ENABLE -+ : CPR4_MARGIN_ADJ_CTL_HW_CLOSED_LOOP_DISABLE); -+ } else if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR3) { -+ cpr3_write(ctrl, CPR3_REG_HW_CLOSED_LOOP, -+ ctrl->use_hw_closed_loop -+ ? CPR3_HW_CLOSED_LOOP_ENABLE -+ : CPR3_HW_CLOSED_LOOP_DISABLE); -+ -+ cpr3_debug(ctrl, "PD_THROTTLE=0x%08X\n", -+ ctrl->proc_clock_throttle); -+ } -+ -+ if ((ctrl->use_hw_closed_loop || -+ ctrl->ctrl_type == CPR_CTRL_TYPE_CPR4) && -+ ctrl->vdd_limit_regulator) { -+ rc = regulator_enable(ctrl->vdd_limit_regulator); -+ if (rc) { -+ cpr3_err(ctrl, "CPR limit regulator enable failed, rc=%d\n", -+ rc); -+ return rc; -+ } -+ } -+ } -+ -+ if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR4) { -+ rc = cpr3_regulator_init_cpr4(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "CPR4-specific controller initialization failed, rc=%d\n", -+ rc); -+ return rc; -+ } -+ } -+ -+ /* Ensure that all register writes complete before disabling clocks. */ -+ wmb(); -+ -+ cpr3_clock_disable(ctrl); -+ ctrl->cpr_enabled = false; -+ -+ if (!ctrl->cpr_allowed_sw || !ctrl->cpr_allowed_hw) -+ mode = "open-loop"; -+ else if (ctrl->supports_hw_closed_loop) -+ mode = ctrl->use_hw_closed_loop -+ ? "HW closed-loop" : "SW closed-loop"; -+ else -+ mode = "closed-loop"; -+ -+ cpr3_info(ctrl, "Default CPR mode = %s", mode); -+ -+ return 0; -+} -+ -+/** -+ * cpr3_regulator_set_target_quot() - configure the target quotient for each -+ * RO of the CPR3 thread and set the RO mask -+ * @thread: Pointer to the CPR3 thread -+ * -+ * Return: none -+ */ -+static void cpr3_regulator_set_target_quot(struct cpr3_thread *thread) -+{ -+ u32 new_quot, last_quot; -+ int i; -+ -+ if (thread->aggr_corner.ro_mask == CPR3_RO_MASK -+ && thread->last_closed_loop_aggr_corner.ro_mask == CPR3_RO_MASK) { -+ /* Avoid writing target quotients since all RO's are masked. */ -+ return; -+ } else if (thread->aggr_corner.ro_mask == CPR3_RO_MASK) { -+ cpr3_write(thread->ctrl, CPR3_REG_RO_MASK(thread->thread_id), -+ CPR3_RO_MASK); -+ thread->last_closed_loop_aggr_corner.ro_mask = CPR3_RO_MASK; -+ /* -+ * Only the RO_MASK register needs to be written since all -+ * RO's are masked. -+ */ -+ return; -+ } else if (thread->aggr_corner.ro_mask -+ != thread->last_closed_loop_aggr_corner.ro_mask) { -+ cpr3_write(thread->ctrl, CPR3_REG_RO_MASK(thread->thread_id), -+ thread->aggr_corner.ro_mask); -+ } -+ -+ for (i = 0; i < CPR3_RO_COUNT; i++) { -+ new_quot = thread->aggr_corner.target_quot[i]; -+ last_quot = thread->last_closed_loop_aggr_corner.target_quot[i]; -+ if (new_quot != last_quot) -+ cpr3_write(thread->ctrl, -+ CPR3_REG_TARGET_QUOT(thread->thread_id, i), -+ new_quot); -+ } -+ -+ thread->last_closed_loop_aggr_corner = thread->aggr_corner; -+ -+ return; -+} -+ -+/** -+ * cpr3_update_vreg_closed_loop_volt() - update the last known settled -+ * closed loop voltage for a CPR3 regulator -+ * @vreg: Pointer to the CPR3 regulator -+ * @vdd_volt: Last known settled voltage in microvolts for the -+ * VDD supply -+ * @reg_last_measurement: Value read from the LAST_MEASUREMENT register -+ * -+ * Return: none -+ */ -+static void cpr3_update_vreg_closed_loop_volt(struct cpr3_regulator *vreg, -+ int vdd_volt, u32 reg_last_measurement) -+{ -+ bool step_dn, step_up, aggr_step_up, aggr_step_dn, aggr_step_mid; -+ bool valid, pd_valid, saw_error; -+ struct cpr3_controller *ctrl = vreg->thread->ctrl; -+ struct cpr3_corner *corner; -+ u32 id; -+ -+ if (vreg->last_closed_loop_corner == CPR3_REGULATOR_CORNER_INVALID) -+ return; -+ else -+ corner = &vreg->corner[vreg->last_closed_loop_corner]; -+ -+ if (vreg->thread->last_closed_loop_aggr_corner.ro_mask -+ == CPR3_RO_MASK || !vreg->aggregated) { -+ return; -+ } else if (!ctrl->cpr_enabled || !ctrl->last_corner_was_closed_loop) { -+ return; -+ } else if (ctrl->thread_count == 1 -+ && vdd_volt >= corner->floor_volt -+ && vdd_volt <= corner->ceiling_volt) { -+ corner->last_volt = vdd_volt; -+ cpr3_debug(vreg, "last_volt updated: last_volt[%d]=%d, ceiling_volt[%d]=%d, floor_volt[%d]=%d\n", -+ vreg->last_closed_loop_corner, corner->last_volt, -+ vreg->last_closed_loop_corner, -+ corner->ceiling_volt, -+ vreg->last_closed_loop_corner, -+ corner->floor_volt); -+ return; -+ } else if (!ctrl->supports_hw_closed_loop) { -+ return; -+ } else if (ctrl->ctrl_type != CPR_CTRL_TYPE_CPR3) { -+ corner->last_volt = vdd_volt; -+ cpr3_debug(vreg, "last_volt updated: last_volt[%d]=%d, ceiling_volt[%d]=%d, floor_volt[%d]=%d\n", -+ vreg->last_closed_loop_corner, corner->last_volt, -+ vreg->last_closed_loop_corner, -+ corner->ceiling_volt, -+ vreg->last_closed_loop_corner, -+ corner->floor_volt); -+ return; -+ } -+ -+ /* CPR clocks are on and HW closed loop is supported */ -+ valid = !!(reg_last_measurement & CPR3_LAST_MEASUREMENT_VALID); -+ if (!valid) { -+ cpr3_debug(vreg, "CPR_LAST_VALID_MEASUREMENT=0x%X valid bit not set\n", -+ reg_last_measurement); -+ return; -+ } -+ -+ id = vreg->thread->thread_id; -+ -+ step_dn -+ = !!(reg_last_measurement & CPR3_LAST_MEASUREMENT_THREAD_DN(id)); -+ step_up -+ = !!(reg_last_measurement & CPR3_LAST_MEASUREMENT_THREAD_UP(id)); -+ aggr_step_dn = !!(reg_last_measurement & CPR3_LAST_MEASUREMENT_AGGR_DN); -+ aggr_step_mid -+ = !!(reg_last_measurement & CPR3_LAST_MEASUREMENT_AGGR_MID); -+ aggr_step_up = !!(reg_last_measurement & CPR3_LAST_MEASUREMENT_AGGR_UP); -+ saw_error = !!(reg_last_measurement & CPR3_LAST_MEASUREMENT_SAW_ERROR); -+ pd_valid -+ = !((((reg_last_measurement & CPR3_LAST_MEASUREMENT_PD_BYPASS_MASK) -+ >> CPR3_LAST_MEASUREMENT_PD_BYPASS_SHIFT) -+ & vreg->pd_bypass_mask) == vreg->pd_bypass_mask); -+ -+ if (!pd_valid) { -+ cpr3_debug(vreg, "CPR_LAST_VALID_MEASUREMENT=0x%X, all power domains bypassed\n", -+ reg_last_measurement); -+ return; -+ } else if (step_dn && step_up) { -+ cpr3_err(vreg, "both up and down status bits set, CPR_LAST_VALID_MEASUREMENT=0x%X\n", -+ reg_last_measurement); -+ return; -+ } else if (aggr_step_dn && step_dn && vdd_volt < corner->last_volt -+ && vdd_volt >= corner->floor_volt) { -+ corner->last_volt = vdd_volt; -+ } else if (aggr_step_up && step_up && vdd_volt > corner->last_volt -+ && vdd_volt <= corner->ceiling_volt) { -+ corner->last_volt = vdd_volt; -+ } else if (aggr_step_mid -+ && vdd_volt >= corner->floor_volt -+ && vdd_volt <= corner->ceiling_volt) { -+ corner->last_volt = vdd_volt; -+ } else if (saw_error && (vdd_volt == corner->ceiling_volt -+ || vdd_volt == corner->floor_volt)) { -+ corner->last_volt = vdd_volt; -+ } else { -+ cpr3_debug(vreg, "last_volt not updated: last_volt[%d]=%d, ceiling_volt[%d]=%d, floor_volt[%d]=%d, vdd_volt=%d, CPR_LAST_VALID_MEASUREMENT=0x%X\n", -+ vreg->last_closed_loop_corner, corner->last_volt, -+ vreg->last_closed_loop_corner, -+ corner->ceiling_volt, -+ vreg->last_closed_loop_corner, corner->floor_volt, -+ vdd_volt, reg_last_measurement); -+ return; -+ } -+ -+ cpr3_debug(vreg, "last_volt updated: last_volt[%d]=%d, ceiling_volt[%d]=%d, floor_volt[%d]=%d, CPR_LAST_VALID_MEASUREMENT=0x%X\n", -+ vreg->last_closed_loop_corner, corner->last_volt, -+ vreg->last_closed_loop_corner, corner->ceiling_volt, -+ vreg->last_closed_loop_corner, corner->floor_volt, -+ reg_last_measurement); -+} -+ -+/** -+ * cpr3_regulator_mem_acc_bhs_used() - determines if mem-acc regulators powered -+ * through a BHS are associated with the CPR3 controller or any of -+ * the CPR3 regulators it controls. -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * This function determines if the CPR3 controller or any of its CPR3 regulators -+ * need to manage mem-acc regulators that are currently powered through a BHS -+ * and whose corner selection is based upon a particular voltage threshold. -+ * -+ * Return: true or false -+ */ -+static bool cpr3_regulator_mem_acc_bhs_used(struct cpr3_controller *ctrl) -+{ -+ struct cpr3_regulator *vreg; -+ int i, j; -+ -+ if (!ctrl->mem_acc_threshold_volt) -+ return false; -+ -+ if (ctrl->mem_acc_regulator) -+ return true; -+ -+ for (i = 0; i < ctrl->thread_count; i++) { -+ for (j = 0; j < ctrl->thread[i].vreg_count; j++) { -+ vreg = &ctrl->thread[i].vreg[j]; -+ -+ if (vreg->mem_acc_regulator) -+ return true; -+ } -+ } -+ -+ return false; -+} -+ -+/** -+ * cpr3_regulator_config_bhs_mem_acc() - configure the mem-acc regulator -+ * settings for hardware blocks currently powered through the BHS. -+ * @ctrl: Pointer to the CPR3 controller -+ * @new_volt: New voltage in microvolts that VDD supply needs to -+ * end up at -+ * @last_volt: Pointer to the last known voltage in microvolts for the -+ * VDD supply -+ * @aggr_corner: Pointer to the CPR3 corner which corresponds to the max -+ * corner aggregated from all CPR3 threads managed by the -+ * CPR3 controller -+ * -+ * This function programs the mem-acc regulator corners for CPR3 regulators -+ * whose LDO regulators are in bypassed state. The function also handles -+ * CPR3 controllers which utilize mem-acc regulators that operate independently -+ * from the LDO hardware and that must be programmed when the VDD supply -+ * crosses a particular voltage threshold. -+ * -+ * Return: 0 on success, errno on failure. If the VDD supply voltage is -+ * modified, last_volt is updated to reflect the new voltage setpoint. -+ */ -+static int cpr3_regulator_config_bhs_mem_acc(struct cpr3_controller *ctrl, -+ int new_volt, int *last_volt, -+ struct cpr3_corner *aggr_corner) -+{ -+ struct cpr3_regulator *vreg; -+ int i, j, rc, mem_acc_corn, safe_volt; -+ int mem_acc_volt = ctrl->mem_acc_threshold_volt; -+ int ref_volt; -+ -+ if (!cpr3_regulator_mem_acc_bhs_used(ctrl)) -+ return 0; -+ -+ ref_volt = ctrl->use_hw_closed_loop ? aggr_corner->floor_volt : -+ new_volt; -+ -+ if (((*last_volt < mem_acc_volt && mem_acc_volt <= ref_volt) || -+ (*last_volt >= mem_acc_volt && mem_acc_volt > ref_volt))) { -+ if (ref_volt < *last_volt) -+ safe_volt = max(mem_acc_volt, aggr_corner->last_volt); -+ else -+ safe_volt = max(mem_acc_volt, *last_volt); -+ -+ rc = regulator_set_voltage(ctrl->vdd_regulator, safe_volt, -+ new_volt < *last_volt ? -+ ctrl->aggr_corner.ceiling_volt : -+ new_volt); -+ if (rc) { -+ cpr3_err(ctrl, "regulator_set_voltage(vdd) == %d failed, rc=%d\n", -+ safe_volt, rc); -+ return rc; -+ } -+ -+ *last_volt = safe_volt; -+ -+ mem_acc_corn = ref_volt < mem_acc_volt ? -+ ctrl->mem_acc_corner_map[CPR3_MEM_ACC_LOW_CORNER] : -+ ctrl->mem_acc_corner_map[CPR3_MEM_ACC_HIGH_CORNER]; -+ -+ if (ctrl->mem_acc_regulator) { -+ rc = regulator_set_voltage(ctrl->mem_acc_regulator, -+ mem_acc_corn, mem_acc_corn); -+ if (rc) { -+ cpr3_err(ctrl, "regulator_set_voltage(mem_acc) == %d failed, rc=%d\n", -+ mem_acc_corn, rc); -+ return rc; -+ } -+ } -+ -+ for (i = 0; i < ctrl->thread_count; i++) { -+ for (j = 0; j < ctrl->thread[i].vreg_count; j++) { -+ vreg = &ctrl->thread[i].vreg[j]; -+ -+ if (!vreg->mem_acc_regulator) -+ continue; -+ -+ rc = regulator_set_voltage( -+ vreg->mem_acc_regulator, mem_acc_corn, -+ mem_acc_corn); -+ if (rc) { -+ cpr3_err(vreg, "regulator_set_voltage(mem_acc) == %d failed, rc=%d\n", -+ mem_acc_corn, rc); -+ return rc; -+ } -+ } -+ } -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr3_regulator_switch_apm_mode() - switch the mode of the APM controller -+ * associated with a given CPR3 controller -+ * @ctrl: Pointer to the CPR3 controller -+ * @new_volt: New voltage in microvolts that VDD supply needs to -+ * end up at -+ * @last_volt: Pointer to the last known voltage in microvolts for the -+ * VDD supply -+ * @aggr_corner: Pointer to the CPR3 corner which corresponds to the max -+ * corner aggregated from all CPR3 threads managed by the -+ * CPR3 controller -+ * -+ * This function requests a switch of the APM mode while guaranteeing -+ * any LDO regulator hardware requirements are satisfied. The function must -+ * be called once it is known a new VDD supply setpoint crosses the APM -+ * voltage threshold. -+ * -+ * Return: 0 on success, errno on failure. If the VDD supply voltage is -+ * modified, last_volt is updated to reflect the new voltage setpoint. -+ */ -+static int cpr3_regulator_switch_apm_mode(struct cpr3_controller *ctrl, -+ int new_volt, int *last_volt, -+ struct cpr3_corner *aggr_corner) -+{ -+ struct regulator *vdd = ctrl->vdd_regulator; -+ int apm_volt = ctrl->apm_threshold_volt; -+ int orig_last_volt = *last_volt; -+ int rc; -+ -+ rc = regulator_set_voltage(vdd, apm_volt, apm_volt); -+ if (rc) { -+ cpr3_err(ctrl, "regulator_set_voltage(vdd) == %d failed, rc=%d\n", -+ apm_volt, rc); -+ return rc; -+ } -+ -+ *last_volt = apm_volt; -+ -+ rc = msm_apm_set_supply(ctrl->apm, new_volt >= apm_volt -+ ? ctrl->apm_high_supply : ctrl->apm_low_supply); -+ if (rc) { -+ cpr3_err(ctrl, "APM switch failed, rc=%d\n", rc); -+ /* Roll back the voltage. */ -+ regulator_set_voltage(vdd, orig_last_volt, INT_MAX); -+ *last_volt = orig_last_volt; -+ return rc; -+ } -+ return 0; -+} -+ -+/** -+ * cpr3_regulator_config_voltage_crossings() - configure APM and mem-acc -+ * settings depending upon a new VDD supply setpoint -+ * -+ * @ctrl: Pointer to the CPR3 controller -+ * @new_volt: New voltage in microvolts that VDD supply needs to -+ * end up at -+ * @last_volt: Pointer to the last known voltage in microvolts for the -+ * VDD supply -+ * @aggr_corner: Pointer to the CPR3 corner which corresponds to the max -+ * corner aggregated from all CPR3 threads managed by the -+ * CPR3 controller -+ * -+ * This function handles the APM and mem-acc regulator reconfiguration if -+ * the new VDD supply voltage will result in crossing their respective voltage -+ * thresholds. -+ * -+ * Return: 0 on success, errno on failure. If the VDD supply voltage is -+ * modified, last_volt is updated to reflect the new voltage setpoint. -+ */ -+static int cpr3_regulator_config_voltage_crossings(struct cpr3_controller *ctrl, -+ int new_volt, int *last_volt, -+ struct cpr3_corner *aggr_corner) -+{ -+ bool apm_crossing = false, mem_acc_crossing = false; -+ bool mem_acc_bhs_used; -+ int apm_volt = ctrl->apm_threshold_volt; -+ int mem_acc_volt = ctrl->mem_acc_threshold_volt; -+ int ref_volt, rc; -+ -+ if (ctrl->apm && apm_volt > 0 -+ && ((*last_volt < apm_volt && apm_volt <= new_volt) -+ || (*last_volt >= apm_volt && apm_volt > new_volt))) -+ apm_crossing = true; -+ -+ mem_acc_bhs_used = cpr3_regulator_mem_acc_bhs_used(ctrl); -+ -+ ref_volt = ctrl->use_hw_closed_loop ? aggr_corner->floor_volt : -+ new_volt; -+ -+ if (mem_acc_bhs_used && -+ (((*last_volt < mem_acc_volt && mem_acc_volt <= ref_volt) || -+ (*last_volt >= mem_acc_volt && mem_acc_volt > ref_volt)))) -+ mem_acc_crossing = true; -+ -+ if (apm_crossing && mem_acc_crossing) { -+ if ((new_volt < *last_volt && apm_volt >= mem_acc_volt) || -+ (new_volt >= *last_volt && apm_volt < mem_acc_volt)) { -+ rc = cpr3_regulator_switch_apm_mode(ctrl, new_volt, -+ last_volt, -+ aggr_corner); -+ if (rc) { -+ cpr3_err(ctrl, "unable to switch APM mode\n"); -+ return rc; -+ } -+ -+ rc = cpr3_regulator_config_bhs_mem_acc(ctrl, new_volt, -+ last_volt, aggr_corner); -+ if (rc) { -+ cpr3_err(ctrl, "unable to configure BHS mem-acc settings\n"); -+ return rc; -+ } -+ } else { -+ rc = cpr3_regulator_config_bhs_mem_acc(ctrl, new_volt, -+ last_volt, aggr_corner); -+ if (rc) { -+ cpr3_err(ctrl, "unable to configure BHS mem-acc settings\n"); -+ return rc; -+ } -+ -+ rc = cpr3_regulator_switch_apm_mode(ctrl, new_volt, -+ last_volt, -+ aggr_corner); -+ if (rc) { -+ cpr3_err(ctrl, "unable to switch APM mode\n"); -+ return rc; -+ } -+ } -+ } else if (apm_crossing) { -+ rc = cpr3_regulator_switch_apm_mode(ctrl, new_volt, last_volt, -+ aggr_corner); -+ if (rc) { -+ cpr3_err(ctrl, "unable to switch APM mode\n"); -+ return rc; -+ } -+ } else if (mem_acc_crossing) { -+ rc = cpr3_regulator_config_bhs_mem_acc(ctrl, new_volt, -+ last_volt, aggr_corner); -+ if (rc) { -+ cpr3_err(ctrl, "unable to configure BHS mem-acc settings\n"); -+ return rc; -+ } -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr3_regulator_config_mem_acc() - configure the corner of the mem-acc -+ * regulator associated with the CPR3 controller -+ * @ctrl: Pointer to the CPR3 controller -+ * @aggr_corner: Pointer to the CPR3 corner which corresponds to the max -+ * corner aggregated from all CPR3 threads managed by the -+ * CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_regulator_config_mem_acc(struct cpr3_controller *ctrl, -+ struct cpr3_corner *aggr_corner) -+{ -+ int rc; -+ -+ if (ctrl->mem_acc_regulator && aggr_corner->mem_acc_volt) { -+ rc = regulator_set_voltage(ctrl->mem_acc_regulator, -+ aggr_corner->mem_acc_volt, -+ aggr_corner->mem_acc_volt); -+ if (rc) { -+ cpr3_err(ctrl, "regulator_set_voltage(mem_acc) == %d failed, rc=%d\n", -+ aggr_corner->mem_acc_volt, rc); -+ return rc; -+ } -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr3_regulator_scale_vdd_voltage() - scale the CPR controlled VDD supply -+ * voltage to the new level while satisfying any other hardware -+ * requirements -+ * @ctrl: Pointer to the CPR3 controller -+ * @new_volt: New voltage in microvolts that VDD supply needs to end -+ * up at -+ * @last_volt: Last known voltage in microvolts for the VDD supply -+ * @aggr_corner: Pointer to the CPR3 corner which corresponds to the max -+ * corner aggregated from all CPR3 threads managed by the -+ * CPR3 controller -+ * -+ * This function scales the CPR controlled VDD supply voltage from its -+ * current level to the new voltage that is specified. If the supply is -+ * configured to use the APM and the APM threshold is crossed as a result of -+ * the voltage scaling, then this function also stops at the APM threshold, -+ * switches the APM source, and finally sets the final new voltage. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_regulator_scale_vdd_voltage(struct cpr3_controller *ctrl, -+ int new_volt, int last_volt, -+ struct cpr3_corner *aggr_corner) -+{ -+ struct regulator *vdd = ctrl->vdd_regulator; -+ int rc; -+ -+ if (new_volt < last_volt) { -+ rc = cpr3_regulator_config_mem_acc(ctrl, aggr_corner); -+ if (rc) -+ return rc; -+ } else { -+ /* Increasing VDD voltage */ -+ if (ctrl->system_regulator) { -+ rc = regulator_set_voltage(ctrl->system_regulator, -+ aggr_corner->system_volt, INT_MAX); -+ if (rc) { -+ cpr3_err(ctrl, "regulator_set_voltage(system) == %d failed, rc=%d\n", -+ aggr_corner->system_volt, rc); -+ return rc; -+ } -+ } -+ } -+ -+ rc = cpr3_regulator_config_voltage_crossings(ctrl, new_volt, &last_volt, -+ aggr_corner); -+ if (rc) { -+ cpr3_err(ctrl, "unable to handle voltage threshold crossing configurations, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ /* -+ * Subtract a small amount from the min_uV parameter so that the -+ * set voltage request is not dropped by the framework due to being -+ * duplicate. This is needed in order to switch from hardware -+ * closed-loop to open-loop successfully. -+ */ -+ rc = regulator_set_voltage(vdd, new_volt - (ctrl->cpr_enabled ? 0 : 1), -+ aggr_corner->ceiling_volt); -+ if (rc) { -+ cpr3_err(ctrl, "regulator_set_voltage(vdd) == %d failed, rc=%d\n", -+ new_volt, rc); -+ return rc; -+ } -+ -+ if (new_volt == last_volt && ctrl->supports_hw_closed_loop -+ && ctrl->ctrl_type == CPR_CTRL_TYPE_CPR4) { -+ /* -+ * CPR4 features enforce voltage reprogramming when the last -+ * set voltage and new set voltage are same. This way, we can -+ * ensure that SAW PMIC STATUS register is updated with newly -+ * programmed voltage. -+ */ -+ rc = regulator_sync_voltage(vdd); -+ if (rc) { -+ cpr3_err(ctrl, "regulator_sync_voltage(vdd) == %d failed, rc=%d\n", -+ new_volt, rc); -+ return rc; -+ } -+ } -+ -+ if (new_volt >= last_volt) { -+ rc = cpr3_regulator_config_mem_acc(ctrl, aggr_corner); -+ if (rc) -+ return rc; -+ } else { -+ /* Decreasing VDD voltage */ -+ if (ctrl->system_regulator) { -+ rc = regulator_set_voltage(ctrl->system_regulator, -+ aggr_corner->system_volt, INT_MAX); -+ if (rc) { -+ cpr3_err(ctrl, "regulator_set_voltage(system) == %d failed, rc=%d\n", -+ aggr_corner->system_volt, rc); -+ return rc; -+ } -+ } -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr3_regulator_get_dynamic_floor_volt() - returns the current dynamic floor -+ * voltage based upon static configurations and the state of all -+ * power domains during the last CPR measurement -+ * @ctrl: Pointer to the CPR3 controller -+ * @reg_last_measurement: Value read from the LAST_MEASUREMENT register -+ * -+ * When using HW closed-loop, the dynamic floor voltage is always returned -+ * regardless of the current state of the power domains. -+ * -+ * Return: dynamic floor voltage in microvolts or 0 if dynamic floor is not -+ * currently required -+ */ -+static int cpr3_regulator_get_dynamic_floor_volt(struct cpr3_controller *ctrl, -+ u32 reg_last_measurement) -+{ -+ int dynamic_floor_volt = 0; -+ struct cpr3_regulator *vreg; -+ bool valid, pd_valid; -+ u32 bypass_bits; -+ int i, j; -+ -+ if (!ctrl->supports_hw_closed_loop) -+ return 0; -+ -+ if (likely(!ctrl->use_hw_closed_loop)) { -+ valid = !!(reg_last_measurement & CPR3_LAST_MEASUREMENT_VALID); -+ bypass_bits -+ = (reg_last_measurement & CPR3_LAST_MEASUREMENT_PD_BYPASS_MASK) -+ >> CPR3_LAST_MEASUREMENT_PD_BYPASS_SHIFT; -+ } else { -+ /* -+ * Ensure that the dynamic floor voltage is always used for -+ * HW closed-loop since the conditions below cannot be evaluated -+ * after each CPR measurement. -+ */ -+ valid = false; -+ bypass_bits = 0; -+ } -+ -+ for (i = 0; i < ctrl->thread_count; i++) { -+ for (j = 0; j < ctrl->thread[i].vreg_count; j++) { -+ vreg = &ctrl->thread[i].vreg[j]; -+ -+ if (!vreg->uses_dynamic_floor) -+ continue; -+ -+ pd_valid = !((bypass_bits & vreg->pd_bypass_mask) -+ == vreg->pd_bypass_mask); -+ -+ if (!valid || !pd_valid) -+ dynamic_floor_volt = max(dynamic_floor_volt, -+ vreg->corner[ -+ vreg->dynamic_floor_corner].last_volt); -+ } -+ } -+ -+ return dynamic_floor_volt; -+} -+ -+/** -+ * cpr3_regulator_max_sdelta_diff() - returns the maximum voltage difference in -+ * microvolts that can result from different operating conditions -+ * for the specified sdelta struct -+ * @sdelta: Pointer to the sdelta structure -+ * @step_volt: Step size in microvolts between available set -+ * points of the VDD supply. -+ * -+ * Return: voltage difference between the highest and lowest adjustments if -+ * sdelta and sdelta->table are valid, else 0. -+ */ -+static int cpr3_regulator_max_sdelta_diff(const struct cpr4_sdelta *sdelta, -+ int step_volt) -+{ -+ int i, j, index, sdelta_min = INT_MAX, sdelta_max = INT_MIN; -+ -+ if (!sdelta || !sdelta->table) -+ return 0; -+ -+ for (i = 0; i < sdelta->max_core_count; i++) { -+ for (j = 0; j < sdelta->temp_band_count; j++) { -+ index = i * sdelta->temp_band_count + j; -+ sdelta_min = min(sdelta_min, sdelta->table[index]); -+ sdelta_max = max(sdelta_max, sdelta->table[index]); -+ } -+ } -+ -+ return (sdelta_max - sdelta_min) * step_volt; -+} -+ -+/** -+ * cpr3_regulator_aggregate_sdelta() - check open-loop voltages of current -+ * aggregated corner and current corner of a given regulator -+ * and adjust the sdelta strucuture data of aggregate corner. -+ * @aggr_corner: Pointer to accumulated aggregated corner which -+ * is both an input and an output -+ * @corner: Pointer to the corner to be aggregated with -+ * aggr_corner -+ * @step_volt: Step size in microvolts between available set -+ * points of the VDD supply. -+ * -+ * Return: none -+ */ -+static void cpr3_regulator_aggregate_sdelta( -+ struct cpr3_corner *aggr_corner, -+ const struct cpr3_corner *corner, int step_volt) -+{ -+ struct cpr4_sdelta *aggr_sdelta, *sdelta; -+ int aggr_core_count, core_count, temp_band_count; -+ u32 aggr_index, index; -+ int i, j, sdelta_size, cap_steps, adjust_sdelta; -+ -+ aggr_sdelta = aggr_corner->sdelta; -+ sdelta = corner->sdelta; -+ -+ if (aggr_corner->open_loop_volt < corner->open_loop_volt) { -+ /* -+ * Found the new dominant regulator as its open-loop requirement -+ * is higher than previous dominant regulator. Calculate cap -+ * voltage to limit the SDELTA values to make sure the runtime -+ * (Core-count/temp) adjustments do not violate other -+ * regulators' voltage requirements. Use cpr4_sdelta values of -+ * new dominant regulator. -+ */ -+ aggr_sdelta->cap_volt = min(aggr_sdelta->cap_volt, -+ (corner->open_loop_volt - -+ aggr_corner->open_loop_volt)); -+ -+ /* Clear old data in the sdelta table */ -+ sdelta_size = aggr_sdelta->max_core_count -+ * aggr_sdelta->temp_band_count; -+ -+ if (aggr_sdelta->allow_core_count_adj -+ || aggr_sdelta->allow_temp_adj) -+ memset(aggr_sdelta->table, 0, sdelta_size -+ * sizeof(*aggr_sdelta->table)); -+ -+ if (sdelta->allow_temp_adj || sdelta->allow_core_count_adj) { -+ /* Copy new data in sdelta table */ -+ sdelta_size = sdelta->max_core_count -+ * sdelta->temp_band_count; -+ if (sdelta->table) -+ memcpy(aggr_sdelta->table, sdelta->table, -+ sdelta_size * sizeof(*sdelta->table)); -+ } -+ -+ if (sdelta->allow_boost) { -+ memcpy(aggr_sdelta->boost_table, sdelta->boost_table, -+ sdelta->temp_band_count -+ * sizeof(*sdelta->boost_table)); -+ aggr_sdelta->boost_num_cores = sdelta->boost_num_cores; -+ } else if (aggr_sdelta->allow_boost) { -+ for (i = 0; i < aggr_sdelta->temp_band_count; i++) { -+ adjust_sdelta = (corner->open_loop_volt -+ - aggr_corner->open_loop_volt) -+ / step_volt; -+ aggr_sdelta->boost_table[i] += adjust_sdelta; -+ aggr_sdelta->boost_table[i] -+ = min(aggr_sdelta->boost_table[i], 0); -+ } -+ } -+ -+ aggr_corner->open_loop_volt = corner->open_loop_volt; -+ aggr_sdelta->allow_temp_adj = sdelta->allow_temp_adj; -+ aggr_sdelta->allow_core_count_adj -+ = sdelta->allow_core_count_adj; -+ aggr_sdelta->max_core_count = sdelta->max_core_count; -+ aggr_sdelta->temp_band_count = sdelta->temp_band_count; -+ } else if (aggr_corner->open_loop_volt > corner->open_loop_volt) { -+ /* -+ * Adjust the cap voltage if the open-loop requirement of new -+ * regulator is the next highest. -+ */ -+ aggr_sdelta->cap_volt = min(aggr_sdelta->cap_volt, -+ (aggr_corner->open_loop_volt -+ - corner->open_loop_volt)); -+ -+ if (sdelta->allow_boost) { -+ for (i = 0; i < aggr_sdelta->temp_band_count; i++) { -+ adjust_sdelta = (aggr_corner->open_loop_volt -+ - corner->open_loop_volt) -+ / step_volt; -+ aggr_sdelta->boost_table[i] = -+ sdelta->boost_table[i] + adjust_sdelta; -+ aggr_sdelta->boost_table[i] -+ = min(aggr_sdelta->boost_table[i], 0); -+ } -+ aggr_sdelta->boost_num_cores = sdelta->boost_num_cores; -+ } -+ } else { -+ /* -+ * Found another dominant regulator with same open-loop -+ * requirement. Make cap voltage to '0'. Disable core-count -+ * adjustments as we couldn't support for both regulators. -+ * Keep enable temp based adjustments if enabled for both -+ * regulators and choose mininum margin adjustment values -+ * between them. -+ */ -+ aggr_sdelta->cap_volt = 0; -+ aggr_sdelta->allow_core_count_adj = false; -+ -+ if (aggr_sdelta->allow_temp_adj -+ && sdelta->allow_temp_adj) { -+ aggr_core_count = aggr_sdelta->max_core_count - 1; -+ core_count = sdelta->max_core_count - 1; -+ temp_band_count = sdelta->temp_band_count; -+ for (j = 0; j < temp_band_count; j++) { -+ aggr_index = aggr_core_count * temp_band_count -+ + j; -+ index = core_count * temp_band_count + j; -+ aggr_sdelta->table[aggr_index] = -+ min(aggr_sdelta->table[aggr_index], -+ sdelta->table[index]); -+ } -+ } else { -+ aggr_sdelta->allow_temp_adj = false; -+ } -+ -+ if (sdelta->allow_boost) { -+ memcpy(aggr_sdelta->boost_table, sdelta->boost_table, -+ sdelta->temp_band_count -+ * sizeof(*sdelta->boost_table)); -+ aggr_sdelta->boost_num_cores = sdelta->boost_num_cores; -+ } -+ } -+ -+ /* Keep non-dominant clients boost enable state */ -+ aggr_sdelta->allow_boost |= sdelta->allow_boost; -+ if (aggr_sdelta->allow_boost) -+ aggr_sdelta->allow_core_count_adj = false; -+ -+ if (aggr_sdelta->cap_volt && !(aggr_sdelta->cap_volt == INT_MAX)) { -+ core_count = aggr_sdelta->max_core_count; -+ temp_band_count = aggr_sdelta->temp_band_count; -+ /* -+ * Convert cap voltage from uV to PMIC steps and use to limit -+ * sdelta margin adjustments. -+ */ -+ cap_steps = aggr_sdelta->cap_volt / step_volt; -+ for (i = 0; i < core_count; i++) -+ for (j = 0; j < temp_band_count; j++) { -+ index = i * temp_band_count + j; -+ aggr_sdelta->table[index] = -+ min(aggr_sdelta->table[index], -+ cap_steps); -+ } -+ } -+} -+ -+/** -+ * cpr3_regulator_aggregate_corners() - aggregate two corners together -+ * @aggr_corner: Pointer to accumulated aggregated corner which -+ * is both an input and an output -+ * @corner: Pointer to the corner to be aggregated with -+ * aggr_corner -+ * @aggr_quot: Flag indicating that target quotients should be -+ * aggregated as well. -+ * @step_volt: Step size in microvolts between available set -+ * points of the VDD supply. -+ * -+ * Return: none -+ */ -+static void cpr3_regulator_aggregate_corners(struct cpr3_corner *aggr_corner, -+ const struct cpr3_corner *corner, bool aggr_quot, -+ int step_volt) -+{ -+ int i; -+ -+ aggr_corner->ceiling_volt -+ = max(aggr_corner->ceiling_volt, corner->ceiling_volt); -+ aggr_corner->floor_volt -+ = max(aggr_corner->floor_volt, corner->floor_volt); -+ aggr_corner->last_volt -+ = max(aggr_corner->last_volt, corner->last_volt); -+ aggr_corner->system_volt -+ = max(aggr_corner->system_volt, corner->system_volt); -+ aggr_corner->mem_acc_volt -+ = max(aggr_corner->mem_acc_volt, corner->mem_acc_volt); -+ aggr_corner->irq_en |= corner->irq_en; -+ aggr_corner->use_open_loop |= corner->use_open_loop; -+ -+ if (aggr_quot) { -+ aggr_corner->ro_mask &= corner->ro_mask; -+ -+ for (i = 0; i < CPR3_RO_COUNT; i++) -+ aggr_corner->target_quot[i] -+ = max(aggr_corner->target_quot[i], -+ corner->target_quot[i]); -+ } -+ -+ if (aggr_corner->sdelta && corner->sdelta -+ && (aggr_corner->sdelta->table -+ || aggr_corner->sdelta->boost_table)) { -+ cpr3_regulator_aggregate_sdelta(aggr_corner, corner, step_volt); -+ } else { -+ aggr_corner->open_loop_volt -+ = max(aggr_corner->open_loop_volt, -+ corner->open_loop_volt); -+ } -+} -+ -+/** -+ * cpr3_regulator_update_ctrl_state() - update the state of the CPR controller -+ * to reflect the corners used by all CPR3 regulators as well as -+ * the CPR operating mode -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * This function aggregates the CPR parameters for all CPR3 regulators -+ * associated with the VDD supply. Upon success, it sets the aggregated last -+ * known good voltage. -+ * -+ * The VDD supply voltage will not be physically configured unless this -+ * condition is met by at least one of the regulators of the controller: -+ * regulator->vreg_enabled == true && -+ * regulator->current_corner != CPR3_REGULATOR_CORNER_INVALID -+ * -+ * CPR registers for the controller and each thread are updated as long as -+ * ctrl->cpr_enabled == true. -+ * -+ * Note, CPR3 controller lock must be held by the caller. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int _cpr3_regulator_update_ctrl_state(struct cpr3_controller *ctrl) -+{ -+ struct cpr3_corner aggr_corner = {}; -+ struct cpr3_thread *thread; -+ struct cpr3_regulator *vreg; -+ struct cpr4_sdelta *sdelta; -+ bool valid = false; -+ bool thread_valid; -+ int i, j, rc, new_volt, vdd_volt, dynamic_floor_volt, last_corner_volt; -+ u32 reg_last_measurement = 0, sdelta_size; -+ int *sdelta_table, *boost_table; -+ -+ last_corner_volt = 0; -+ if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR4) { -+ rc = cpr3_ctrl_clear_cpr4_config(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "failed to clear CPR4 configuration,rc=%d\n", -+ rc); -+ return rc; -+ } -+ } -+ -+ cpr3_ctrl_loop_disable(ctrl); -+ -+ vdd_volt = regulator_get_voltage(ctrl->vdd_regulator); -+ if (vdd_volt < 0) { -+ cpr3_err(ctrl, "regulator_get_voltage(vdd) failed, rc=%d\n", -+ vdd_volt); -+ return vdd_volt; -+ } -+ -+ if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR4) { -+ /* -+ * Save aggregated corner open-loop voltage which was programmed -+ * during last corner switch which is used when programming new -+ * aggregated corner open-loop voltage. -+ */ -+ last_corner_volt = ctrl->aggr_corner.open_loop_volt; -+ } -+ -+ if (ctrl->cpr_enabled && ctrl->use_hw_closed_loop && -+ ctrl->ctrl_type == CPR_CTRL_TYPE_CPR3) -+ reg_last_measurement -+ = cpr3_read(ctrl, CPR3_REG_LAST_MEASUREMENT); -+ -+ aggr_corner.sdelta = ctrl->aggr_corner.sdelta; -+ if (aggr_corner.sdelta) { -+ sdelta = aggr_corner.sdelta; -+ sdelta_table = sdelta->table; -+ if (sdelta_table) { -+ sdelta_size = sdelta->max_core_count * -+ sdelta->temp_band_count; -+ memset(sdelta_table, 0, sdelta_size -+ * sizeof(*sdelta_table)); -+ } -+ -+ boost_table = sdelta->boost_table; -+ if (boost_table) -+ memset(boost_table, 0, sdelta->temp_band_count -+ * sizeof(*boost_table)); -+ -+ memset(sdelta, 0, sizeof(*sdelta)); -+ sdelta->table = sdelta_table; -+ sdelta->cap_volt = INT_MAX; -+ sdelta->boost_table = boost_table; -+ } -+ -+ /* Aggregate the requests of all threads */ -+ for (i = 0; i < ctrl->thread_count; i++) { -+ thread = &ctrl->thread[i]; -+ thread_valid = false; -+ -+ sdelta = thread->aggr_corner.sdelta; -+ if (sdelta) { -+ sdelta_table = sdelta->table; -+ if (sdelta_table) { -+ sdelta_size = sdelta->max_core_count * -+ sdelta->temp_band_count; -+ memset(sdelta_table, 0, sdelta_size -+ * sizeof(*sdelta_table)); -+ } -+ -+ boost_table = sdelta->boost_table; -+ if (boost_table) -+ memset(boost_table, 0, sdelta->temp_band_count -+ * sizeof(*boost_table)); -+ -+ memset(sdelta, 0, sizeof(*sdelta)); -+ sdelta->table = sdelta_table; -+ sdelta->cap_volt = INT_MAX; -+ sdelta->boost_table = boost_table; -+ } -+ -+ memset(&thread->aggr_corner, 0, sizeof(thread->aggr_corner)); -+ thread->aggr_corner.sdelta = sdelta; -+ thread->aggr_corner.ro_mask = CPR3_RO_MASK; -+ -+ for (j = 0; j < thread->vreg_count; j++) { -+ vreg = &thread->vreg[j]; -+ -+ if (ctrl->cpr_enabled && ctrl->use_hw_closed_loop) -+ cpr3_update_vreg_closed_loop_volt(vreg, -+ vdd_volt, reg_last_measurement); -+ -+ if (!vreg->vreg_enabled -+ || vreg->current_corner -+ == CPR3_REGULATOR_CORNER_INVALID) { -+ /* Cannot participate in aggregation. */ -+ vreg->aggregated = false; -+ continue; -+ } else { -+ vreg->aggregated = true; -+ thread_valid = true; -+ } -+ -+ cpr3_regulator_aggregate_corners(&thread->aggr_corner, -+ &vreg->corner[vreg->current_corner], -+ true, ctrl->step_volt); -+ } -+ -+ valid |= thread_valid; -+ -+ if (thread_valid) -+ cpr3_regulator_aggregate_corners(&aggr_corner, -+ &thread->aggr_corner, -+ false, ctrl->step_volt); -+ } -+ -+ if (valid && ctrl->cpr_allowed_hw && ctrl->cpr_allowed_sw) { -+ rc = cpr3_closed_loop_enable(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "could not enable CPR, rc=%d\n", rc); -+ return rc; -+ } -+ } else { -+ rc = cpr3_closed_loop_disable(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "could not disable CPR, rc=%d\n", rc); -+ return rc; -+ } -+ } -+ -+ /* No threads are enabled with a valid corner so exit. */ -+ if (!valid) -+ return 0; -+ -+ /* -+ * When using CPR hardware closed-loop, the voltage may vary anywhere -+ * between the floor and ceiling voltage without software notification. -+ * Therefore, it is required that the floor to ceiling range for the -+ * aggregated corner not intersect the APM threshold voltage. Adjust -+ * the floor to ceiling range if this requirement is violated. -+ * -+ * The following algorithm is applied in the case that -+ * floor < threshold <= ceiling: -+ * if open_loop >= threshold - adj, then floor = threshold -+ * else ceiling = threshold - step -+ * where adj = an adjustment factor to ensure sufficient voltage margin -+ * and step = VDD output step size -+ * -+ * The open-loop and last known voltages are also bounded by the new -+ * floor or ceiling value as needed. -+ */ -+ if (ctrl->use_hw_closed_loop -+ && aggr_corner.ceiling_volt >= ctrl->apm_threshold_volt -+ && aggr_corner.floor_volt < ctrl->apm_threshold_volt) { -+ -+ if (aggr_corner.open_loop_volt -+ >= ctrl->apm_threshold_volt - ctrl->apm_adj_volt) -+ aggr_corner.floor_volt = ctrl->apm_threshold_volt; -+ else -+ aggr_corner.ceiling_volt -+ = ctrl->apm_threshold_volt - ctrl->step_volt; -+ -+ aggr_corner.last_volt -+ = max(aggr_corner.last_volt, aggr_corner.floor_volt); -+ aggr_corner.last_volt -+ = min(aggr_corner.last_volt, aggr_corner.ceiling_volt); -+ aggr_corner.open_loop_volt -+ = max(aggr_corner.open_loop_volt, aggr_corner.floor_volt); -+ aggr_corner.open_loop_volt -+ = min(aggr_corner.open_loop_volt, aggr_corner.ceiling_volt); -+ } -+ -+ if (ctrl->use_hw_closed_loop -+ && aggr_corner.ceiling_volt >= ctrl->mem_acc_threshold_volt -+ && aggr_corner.floor_volt < ctrl->mem_acc_threshold_volt) { -+ aggr_corner.floor_volt = ctrl->mem_acc_threshold_volt; -+ aggr_corner.last_volt = max(aggr_corner.last_volt, -+ aggr_corner.floor_volt); -+ aggr_corner.open_loop_volt = max(aggr_corner.open_loop_volt, -+ aggr_corner.floor_volt); -+ } -+ -+ if (ctrl->use_hw_closed_loop) { -+ dynamic_floor_volt -+ = cpr3_regulator_get_dynamic_floor_volt(ctrl, -+ reg_last_measurement); -+ if (aggr_corner.floor_volt < dynamic_floor_volt) { -+ aggr_corner.floor_volt = dynamic_floor_volt; -+ aggr_corner.last_volt = max(aggr_corner.last_volt, -+ aggr_corner.floor_volt); -+ aggr_corner.open_loop_volt -+ = max(aggr_corner.open_loop_volt, -+ aggr_corner.floor_volt); -+ aggr_corner.ceiling_volt = max(aggr_corner.ceiling_volt, -+ aggr_corner.floor_volt); -+ } -+ } -+ -+ if (ctrl->cpr_enabled && ctrl->last_corner_was_closed_loop) { -+ /* -+ * Always program open-loop voltage for CPR4 controllers which -+ * support hardware closed-loop. Storing the last closed loop -+ * voltage in corner structure can still help with debugging. -+ */ -+ if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR3) -+ new_volt = aggr_corner.last_volt; -+ else if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR4 -+ && ctrl->supports_hw_closed_loop) -+ new_volt = aggr_corner.open_loop_volt; -+ else -+ new_volt = min(aggr_corner.last_volt + -+ cpr3_regulator_max_sdelta_diff(aggr_corner.sdelta, -+ ctrl->step_volt), -+ aggr_corner.ceiling_volt); -+ -+ aggr_corner.last_volt = new_volt; -+ } else { -+ new_volt = aggr_corner.open_loop_volt; -+ aggr_corner.last_volt = aggr_corner.open_loop_volt; -+ } -+ -+ if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR4 -+ && ctrl->supports_hw_closed_loop) { -+ /* -+ * Store last aggregated corner open-loop voltage in vdd_volt -+ * which is used when programming current aggregated corner -+ * required voltage. -+ */ -+ vdd_volt = last_corner_volt; -+ } -+ -+ cpr3_debug(ctrl, "setting new voltage=%d uV\n", new_volt); -+ rc = cpr3_regulator_scale_vdd_voltage(ctrl, new_volt, -+ vdd_volt, &aggr_corner); -+ if (rc) { -+ cpr3_err(ctrl, "vdd voltage scaling failed, rc=%d\n", rc); -+ return rc; -+ } -+ -+ /* Only update registers if CPR is enabled. */ -+ if (ctrl->cpr_enabled) { -+ if (ctrl->use_hw_closed_loop) { -+ /* Hardware closed-loop */ -+ -+ /* Set ceiling and floor limits in hardware */ -+ rc = regulator_set_voltage(ctrl->vdd_limit_regulator, -+ aggr_corner.floor_volt, -+ aggr_corner.ceiling_volt); -+ if (rc) { -+ cpr3_err(ctrl, "could not configure HW closed-loop voltage limits, rc=%d\n", -+ rc); -+ return rc; -+ } -+ } else { -+ /* Software closed-loop */ -+ -+ /* -+ * Disable UP or DOWN interrupts when at ceiling or -+ * floor respectively. -+ */ -+ if (new_volt == aggr_corner.floor_volt) -+ aggr_corner.irq_en &= ~CPR3_IRQ_DOWN; -+ if (new_volt == aggr_corner.ceiling_volt) -+ aggr_corner.irq_en &= ~CPR3_IRQ_UP; -+ -+ cpr3_write(ctrl, CPR3_REG_IRQ_CLEAR, -+ CPR3_IRQ_UP | CPR3_IRQ_DOWN); -+ cpr3_write(ctrl, CPR3_REG_IRQ_EN, aggr_corner.irq_en); -+ } -+ -+ for (i = 0; i < ctrl->thread_count; i++) { -+ cpr3_regulator_set_target_quot(&ctrl->thread[i]); -+ -+ for (j = 0; j < ctrl->thread[i].vreg_count; j++) { -+ vreg = &ctrl->thread[i].vreg[j]; -+ -+ if (vreg->vreg_enabled) -+ vreg->last_closed_loop_corner -+ = vreg->current_corner; -+ } -+ } -+ -+ if (ctrl->proc_clock_throttle) { -+ if (aggr_corner.ceiling_volt > aggr_corner.floor_volt -+ && (ctrl->use_hw_closed_loop -+ || new_volt < aggr_corner.ceiling_volt)) -+ cpr3_write(ctrl, CPR3_REG_PD_THROTTLE, -+ ctrl->proc_clock_throttle); -+ else -+ cpr3_write(ctrl, CPR3_REG_PD_THROTTLE, -+ CPR3_PD_THROTTLE_DISABLE); -+ } -+ -+ /* -+ * Ensure that all CPR register writes complete before -+ * re-enabling CPR loop operation. -+ */ -+ wmb(); -+ } else if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR4 -+ && ctrl->vdd_limit_regulator) { -+ /* Set ceiling and floor limits in hardware */ -+ rc = regulator_set_voltage(ctrl->vdd_limit_regulator, -+ aggr_corner.floor_volt, -+ aggr_corner.ceiling_volt); -+ if (rc) { -+ cpr3_err(ctrl, "could not configure HW closed-loop voltage limits, rc=%d\n", -+ rc); -+ return rc; -+ } -+ } -+ -+ ctrl->aggr_corner = aggr_corner; -+ -+ if (ctrl->allow_core_count_adj || ctrl->allow_temp_adj -+ || ctrl->allow_boost) { -+ rc = cpr3_controller_program_sdelta(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "failed to program sdelta, rc=%d\n", rc); -+ return rc; -+ } -+ } -+ -+ /* -+ * Only enable the CPR controller if it is possible to set more than -+ * one vdd-supply voltage. -+ */ -+ if (aggr_corner.ceiling_volt > aggr_corner.floor_volt && -+ !aggr_corner.use_open_loop) -+ cpr3_ctrl_loop_enable(ctrl); -+ -+ ctrl->last_corner_was_closed_loop = ctrl->cpr_enabled; -+ cpr3_debug(ctrl, "CPR configuration updated\n"); -+ -+ return 0; -+} -+ -+/** -+ * cpr3_regulator_wait_for_idle() - wait for the CPR controller to no longer be -+ * busy -+ * @ctrl: Pointer to the CPR3 controller -+ * @max_wait_ns: Max wait time in nanoseconds -+ * -+ * Return: 0 on success or -ETIMEDOUT if the controller was still busy after -+ * the maximum delay time -+ */ -+static int cpr3_regulator_wait_for_idle(struct cpr3_controller *ctrl, -+ s64 max_wait_ns) -+{ -+ ktime_t start, end; -+ s64 time_ns; -+ u32 reg; -+ -+ /* -+ * Ensure that all previous CPR register writes have completed before -+ * checking the status register. -+ */ -+ mb(); -+ -+ start = ktime_get(); -+ do { -+ end = ktime_get(); -+ time_ns = ktime_to_ns(ktime_sub(end, start)); -+ if (time_ns > max_wait_ns) { -+ cpr3_err(ctrl, "CPR controller still busy after %lld us\n", -+ div_s64(time_ns, 1000)); -+ return -ETIMEDOUT; -+ } -+ usleep_range(50, 100); -+ reg = cpr3_read(ctrl, CPR3_REG_CPR_STATUS); -+ } while (reg & CPR3_CPR_STATUS_BUSY_MASK); -+ -+ return 0; -+} -+ -+/** -+ * cmp_int() - int comparison function to be passed into the sort() function -+ * which leads to ascending sorting -+ * @a: First int value -+ * @b: Second int value -+ * -+ * Return: >0 if a > b, 0 if a == b, <0 if a < b -+ */ -+static int cmp_int(const void *a, const void *b) -+{ -+ return *(int *)a - *(int *)b; -+} -+ -+/** -+ * cpr3_regulator_measure_aging() - measure the quotient difference for the -+ * specified CPR aging sensor -+ * @ctrl: Pointer to the CPR3 controller -+ * @aging_sensor: Aging sensor to measure -+ * -+ * Note that vdd-supply must be configured to the aging reference voltage before -+ * calling this function. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_regulator_measure_aging(struct cpr3_controller *ctrl, -+ struct cpr3_aging_sensor_info *aging_sensor) -+{ -+ u32 mask, reg, result, quot_min, quot_max, sel_min, sel_max; -+ u32 quot_min_scaled, quot_max_scaled; -+ u32 gcnt, gcnt_ref, gcnt0_restore, gcnt1_restore, irq_restore; -+ u32 ro_mask_restore, cont_dly_restore, up_down_dly_restore = 0; -+ int quot_delta, quot_delta_scaled, quot_delta_scaled_sum; -+ int *quot_delta_results; -+ int rc, rc2, i, aging_measurement_count, filtered_count; -+ bool is_aging_measurement; -+ -+ quot_delta_results = kcalloc(CPR3_AGING_MEASUREMENT_ITERATIONS, -+ sizeof(*quot_delta_results), GFP_KERNEL); -+ if (!quot_delta_results) -+ return -ENOMEM; -+ -+ if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR4) { -+ rc = cpr3_ctrl_clear_cpr4_config(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "failed to clear CPR4 configuration,rc=%d\n", -+ rc); -+ kfree(quot_delta_results); -+ return rc; -+ } -+ } -+ -+ cpr3_ctrl_loop_disable(ctrl); -+ -+ /* Enable up, down, and mid CPR interrupts */ -+ irq_restore = cpr3_read(ctrl, CPR3_REG_IRQ_EN); -+ cpr3_write(ctrl, CPR3_REG_IRQ_EN, -+ CPR3_IRQ_UP | CPR3_IRQ_DOWN | CPR3_IRQ_MID); -+ -+ /* Ensure that the aging sensor is assigned to CPR thread 0 */ -+ cpr3_write(ctrl, CPR3_REG_SENSOR_OWNER(aging_sensor->sensor_id), 0); -+ -+ /* Switch from HW to SW closed-loop if necessary */ -+ if (ctrl->supports_hw_closed_loop) { -+ if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR4) { -+ cpr3_masked_write(ctrl, CPR4_REG_MARGIN_ADJ_CTL, -+ CPR4_MARGIN_ADJ_CTL_HW_CLOSED_LOOP_EN_MASK, -+ CPR4_MARGIN_ADJ_CTL_HW_CLOSED_LOOP_DISABLE); -+ } else if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR3) { -+ cpr3_write(ctrl, CPR3_REG_HW_CLOSED_LOOP, -+ CPR3_HW_CLOSED_LOOP_DISABLE); -+ } -+ } -+ -+ /* Configure the GCNT for RO0 and RO1 that are used for aging */ -+ gcnt0_restore = cpr3_read(ctrl, CPR3_REG_GCNT(0)); -+ gcnt1_restore = cpr3_read(ctrl, CPR3_REG_GCNT(1)); -+ gcnt_ref = cpr3_regulator_get_gcnt(ctrl); -+ gcnt = gcnt_ref * 3 / 2; -+ cpr3_write(ctrl, CPR3_REG_GCNT(0), gcnt); -+ cpr3_write(ctrl, CPR3_REG_GCNT(1), gcnt); -+ -+ /* Unmask all RO's */ -+ ro_mask_restore = cpr3_read(ctrl, CPR3_REG_RO_MASK(0)); -+ cpr3_write(ctrl, CPR3_REG_RO_MASK(0), 0); -+ -+ /* -+ * Mask all sensors except for the one to measure and bypass all -+ * sensors in collapsible domains. -+ */ -+ for (i = 0; i <= ctrl->sensor_count / 32; i++) { -+ mask = GENMASK(min(31, ctrl->sensor_count - i * 32), 0); -+ if (aging_sensor->sensor_id / 32 >= i -+ && aging_sensor->sensor_id / 32 < (i + 1)) -+ mask &= ~BIT(aging_sensor->sensor_id % 32); -+ cpr3_write(ctrl, CPR3_REG_SENSOR_MASK_WRITE_BANK(i), mask); -+ cpr3_write(ctrl, CPR3_REG_SENSOR_BYPASS_WRITE_BANK(i), -+ aging_sensor->bypass_mask[i]); -+ } -+ -+ /* Set CPR loop delays to 0 us */ -+ if (ctrl->supports_hw_closed_loop -+ && ctrl->ctrl_type == CPR_CTRL_TYPE_CPR3) { -+ cont_dly_restore = cpr3_read(ctrl, CPR3_REG_CPR_TIMER_MID_CONT); -+ up_down_dly_restore = cpr3_read(ctrl, -+ CPR3_REG_CPR_TIMER_UP_DN_CONT); -+ cpr3_write(ctrl, CPR3_REG_CPR_TIMER_MID_CONT, 0); -+ cpr3_write(ctrl, CPR3_REG_CPR_TIMER_UP_DN_CONT, 0); -+ } else { -+ cont_dly_restore = cpr3_read(ctrl, -+ CPR3_REG_CPR_TIMER_AUTO_CONT); -+ cpr3_write(ctrl, CPR3_REG_CPR_TIMER_AUTO_CONT, 0); -+ } -+ -+ /* Set count mode to all-at-once min with no repeat */ -+ cpr3_masked_write(ctrl, CPR3_REG_CPR_CTL, -+ CPR3_CPR_CTL_COUNT_MODE_MASK | CPR3_CPR_CTL_COUNT_REPEAT_MASK, -+ CPR3_CPR_CTL_COUNT_MODE_ALL_AT_ONCE_MIN -+ << CPR3_CPR_CTL_COUNT_MODE_SHIFT); -+ -+ cpr3_ctrl_loop_enable(ctrl); -+ -+ rc = cpr3_regulator_wait_for_idle(ctrl, -+ CPR3_AGING_MEASUREMENT_TIMEOUT_NS); -+ if (rc) -+ goto cleanup; -+ -+ /* Set count mode to all-at-once aging */ -+ cpr3_masked_write(ctrl, CPR3_REG_CPR_CTL, CPR3_CPR_CTL_COUNT_MODE_MASK, -+ CPR3_CPR_CTL_COUNT_MODE_ALL_AT_ONCE_AGE -+ << CPR3_CPR_CTL_COUNT_MODE_SHIFT); -+ -+ aging_measurement_count = 0; -+ for (i = 0; i < CPR3_AGING_MEASUREMENT_ITERATIONS; i++) { -+ /* Send CONT_NACK */ -+ cpr3_write(ctrl, CPR3_REG_CONT_CMD, CPR3_CONT_CMD_NACK); -+ -+ rc = cpr3_regulator_wait_for_idle(ctrl, -+ CPR3_AGING_MEASUREMENT_TIMEOUT_NS); -+ if (rc) -+ goto cleanup; -+ -+ /* Check for PAGE_IS_AGE flag in status register */ -+ reg = cpr3_read(ctrl, CPR3_REG_CPR_STATUS); -+ is_aging_measurement -+ = reg & CPR3_CPR_STATUS_AGING_MEASUREMENT_MASK; -+ -+ /* Read CPR measurement results */ -+ result = cpr3_read(ctrl, CPR3_REG_RESULT1(0)); -+ quot_min = (result & CPR3_RESULT1_QUOT_MIN_MASK) -+ >> CPR3_RESULT1_QUOT_MIN_SHIFT; -+ quot_max = (result & CPR3_RESULT1_QUOT_MAX_MASK) -+ >> CPR3_RESULT1_QUOT_MAX_SHIFT; -+ sel_min = (result & CPR3_RESULT1_RO_MIN_MASK) -+ >> CPR3_RESULT1_RO_MIN_SHIFT; -+ sel_max = (result & CPR3_RESULT1_RO_MAX_MASK) -+ >> CPR3_RESULT1_RO_MAX_SHIFT; -+ -+ /* -+ * Scale the quotients so that they are equivalent to the fused -+ * values. This accounts for the difference in measurement -+ * interval times. -+ */ -+ quot_min_scaled = quot_min * (gcnt_ref + 1) / (gcnt + 1); -+ quot_max_scaled = quot_max * (gcnt_ref + 1) / (gcnt + 1); -+ -+ if (sel_max == 1) { -+ quot_delta = quot_max - quot_min; -+ quot_delta_scaled = quot_max_scaled - quot_min_scaled; -+ } else { -+ quot_delta = quot_min - quot_max; -+ quot_delta_scaled = quot_min_scaled - quot_max_scaled; -+ } -+ -+ if (is_aging_measurement) -+ quot_delta_results[aging_measurement_count++] -+ = quot_delta_scaled; -+ -+ cpr3_debug(ctrl, "aging results: page_is_age=%u, sel_min=%u, sel_max=%u, quot_min=%u, quot_max=%u, quot_delta=%d, quot_min_scaled=%u, quot_max_scaled=%u, quot_delta_scaled=%d\n", -+ is_aging_measurement, sel_min, sel_max, quot_min, -+ quot_max, quot_delta, quot_min_scaled, quot_max_scaled, -+ quot_delta_scaled); -+ } -+ -+ filtered_count -+ = aging_measurement_count - CPR3_AGING_MEASUREMENT_FILTER * 2; -+ if (filtered_count > 0) { -+ sort(quot_delta_results, aging_measurement_count, -+ sizeof(*quot_delta_results), cmp_int, NULL); -+ -+ quot_delta_scaled_sum = 0; -+ for (i = 0; i < filtered_count; i++) -+ quot_delta_scaled_sum -+ += quot_delta_results[i -+ + CPR3_AGING_MEASUREMENT_FILTER]; -+ -+ aging_sensor->measured_quot_diff -+ = quot_delta_scaled_sum / filtered_count; -+ cpr3_info(ctrl, "average quotient delta=%d (count=%d)\n", -+ aging_sensor->measured_quot_diff, -+ filtered_count); -+ } else { -+ cpr3_err(ctrl, "%d aging measurements completed after %d iterations\n", -+ aging_measurement_count, -+ CPR3_AGING_MEASUREMENT_ITERATIONS); -+ rc = -EBUSY; -+ } -+ -+cleanup: -+ kfree(quot_delta_results); -+ -+ if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR4) { -+ rc2 = cpr3_ctrl_clear_cpr4_config(ctrl); -+ if (rc2) { -+ cpr3_err(ctrl, "failed to clear CPR4 configuration,rc=%d\n", -+ rc2); -+ rc = rc2; -+ } -+ } -+ -+ cpr3_ctrl_loop_disable(ctrl); -+ -+ cpr3_write(ctrl, CPR3_REG_IRQ_EN, irq_restore); -+ -+ cpr3_write(ctrl, CPR3_REG_RO_MASK(0), ro_mask_restore); -+ -+ cpr3_write(ctrl, CPR3_REG_GCNT(0), gcnt0_restore); -+ cpr3_write(ctrl, CPR3_REG_GCNT(1), gcnt1_restore); -+ -+ if (ctrl->supports_hw_closed_loop -+ && ctrl->ctrl_type == CPR_CTRL_TYPE_CPR3) { -+ cpr3_write(ctrl, CPR3_REG_CPR_TIMER_MID_CONT, cont_dly_restore); -+ cpr3_write(ctrl, CPR3_REG_CPR_TIMER_UP_DN_CONT, -+ up_down_dly_restore); -+ } else { -+ cpr3_write(ctrl, CPR3_REG_CPR_TIMER_AUTO_CONT, -+ cont_dly_restore); -+ } -+ -+ for (i = 0; i <= ctrl->sensor_count / 32; i++) { -+ cpr3_write(ctrl, CPR3_REG_SENSOR_MASK_WRITE_BANK(i), 0); -+ cpr3_write(ctrl, CPR3_REG_SENSOR_BYPASS_WRITE_BANK(i), 0); -+ } -+ -+ cpr3_masked_write(ctrl, CPR3_REG_CPR_CTL, -+ CPR3_CPR_CTL_COUNT_MODE_MASK | CPR3_CPR_CTL_COUNT_REPEAT_MASK, -+ (ctrl->count_mode << CPR3_CPR_CTL_COUNT_MODE_SHIFT) -+ | (ctrl->count_repeat << CPR3_CPR_CTL_COUNT_REPEAT_SHIFT)); -+ -+ cpr3_write(ctrl, CPR3_REG_SENSOR_OWNER(aging_sensor->sensor_id), -+ ctrl->sensor_owner[aging_sensor->sensor_id]); -+ -+ cpr3_write(ctrl, CPR3_REG_IRQ_CLEAR, -+ CPR3_IRQ_UP | CPR3_IRQ_DOWN | CPR3_IRQ_MID); -+ -+ if (ctrl->supports_hw_closed_loop) { -+ if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR4) { -+ cpr3_masked_write(ctrl, CPR4_REG_MARGIN_ADJ_CTL, -+ CPR4_MARGIN_ADJ_CTL_HW_CLOSED_LOOP_EN_MASK, -+ ctrl->use_hw_closed_loop -+ ? CPR4_MARGIN_ADJ_CTL_HW_CLOSED_LOOP_ENABLE -+ : CPR4_MARGIN_ADJ_CTL_HW_CLOSED_LOOP_DISABLE); -+ } else if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR3) { -+ cpr3_write(ctrl, CPR3_REG_HW_CLOSED_LOOP, -+ ctrl->use_hw_closed_loop -+ ? CPR3_HW_CLOSED_LOOP_ENABLE -+ : CPR3_HW_CLOSED_LOOP_DISABLE); -+ } -+ } -+ -+ return rc; -+} -+ -+/** -+ * cpr3_regulator_readjust_volt_and_quot() - readjust the target quotients as -+ * well as the floor, ceiling, and open-loop voltages for the -+ * regulator by removing the old adjustment and adding the new one -+ * @vreg: Pointer to the CPR3 regulator -+ * @old_adjust_volt: Old aging adjustment voltage in microvolts -+ * @new_adjust_volt: New aging adjustment voltage in microvolts -+ * -+ * Also reset the cached closed loop voltage (last_volt) to equal the open-loop -+ * voltage for each corner. -+ * -+ * Return: None -+ */ -+static void cpr3_regulator_readjust_volt_and_quot(struct cpr3_regulator *vreg, -+ int old_adjust_volt, int new_adjust_volt) -+{ -+ unsigned long long temp; -+ int i, j, old_volt, new_volt, rounded_volt; -+ -+ if (!vreg->aging_allowed) -+ return; -+ -+ for (i = 0; i < vreg->corner_count; i++) { -+ temp = (unsigned long long)old_adjust_volt -+ * (unsigned long long)vreg->corner[i].aging_derate; -+ do_div(temp, 1000); -+ old_volt = temp; -+ -+ temp = (unsigned long long)new_adjust_volt -+ * (unsigned long long)vreg->corner[i].aging_derate; -+ do_div(temp, 1000); -+ new_volt = temp; -+ -+ old_volt = min(vreg->aging_max_adjust_volt, old_volt); -+ new_volt = min(vreg->aging_max_adjust_volt, new_volt); -+ -+ for (j = 0; j < CPR3_RO_COUNT; j++) { -+ if (vreg->corner[i].target_quot[j] != 0) { -+ vreg->corner[i].target_quot[j] -+ += cpr3_quot_adjustment( -+ vreg->corner[i].ro_scale[j], -+ new_volt) -+ - cpr3_quot_adjustment( -+ vreg->corner[i].ro_scale[j], -+ old_volt); -+ } -+ } -+ -+ rounded_volt = CPR3_ROUND(new_volt, -+ vreg->thread->ctrl->step_volt); -+ -+ if (!vreg->aging_allow_open_loop_adj) -+ rounded_volt = 0; -+ -+ vreg->corner[i].ceiling_volt -+ = vreg->corner[i].unaged_ceiling_volt + rounded_volt; -+ vreg->corner[i].ceiling_volt = min(vreg->corner[i].ceiling_volt, -+ vreg->corner[i].abs_ceiling_volt); -+ vreg->corner[i].floor_volt -+ = vreg->corner[i].unaged_floor_volt + rounded_volt; -+ vreg->corner[i].floor_volt = min(vreg->corner[i].floor_volt, -+ vreg->corner[i].ceiling_volt); -+ vreg->corner[i].open_loop_volt -+ = vreg->corner[i].unaged_open_loop_volt + rounded_volt; -+ vreg->corner[i].open_loop_volt -+ = min(vreg->corner[i].open_loop_volt, -+ vreg->corner[i].ceiling_volt); -+ -+ vreg->corner[i].last_volt = vreg->corner[i].open_loop_volt; -+ -+ cpr3_debug(vreg, "corner %d: applying %d uV closed-loop and %d uV open-loop voltage margin adjustment\n", -+ i, new_volt, rounded_volt); -+ } -+} -+ -+/** -+ * cpr3_regulator_set_aging_ref_adjustment() - adjust target quotients for the -+ * regulators managed by this CPR controller to account for aging -+ * @ctrl: Pointer to the CPR3 controller -+ * @ref_adjust_volt: New aging reference adjustment voltage in microvolts to -+ * apply to all regulators managed by this CPR controller -+ * -+ * The existing aging adjustment as defined by ctrl->aging_ref_adjust_volt is -+ * first removed and then the adjustment is applied. Lastly, the value of -+ * ctrl->aging_ref_adjust_volt is updated to ref_adjust_volt. -+ */ -+static void cpr3_regulator_set_aging_ref_adjustment( -+ struct cpr3_controller *ctrl, int ref_adjust_volt) -+{ -+ struct cpr3_regulator *vreg; -+ int i, j; -+ -+ for (i = 0; i < ctrl->thread_count; i++) { -+ for (j = 0; j < ctrl->thread[i].vreg_count; j++) { -+ vreg = &ctrl->thread[i].vreg[j]; -+ cpr3_regulator_readjust_volt_and_quot(vreg, -+ ctrl->aging_ref_adjust_volt, ref_adjust_volt); -+ } -+ } -+ -+ ctrl->aging_ref_adjust_volt = ref_adjust_volt; -+} -+ -+/** -+ * cpr3_regulator_aging_adjust() - adjust the target quotients for regulators -+ * based on the output of CPR aging sensors -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_regulator_aging_adjust(struct cpr3_controller *ctrl) -+{ -+ struct cpr3_regulator *vreg; -+ struct cpr3_corner restore_aging_corner; -+ struct cpr3_corner *corner; -+ int *restore_current_corner; -+ bool *restore_vreg_enabled; -+ int i, j, id, rc, rc2, vreg_count, aging_volt, max_aging_volt = 0; -+ u32 reg; -+ -+ if (!ctrl->aging_required || !ctrl->cpr_enabled -+ || ctrl->aggr_corner.ceiling_volt == 0 -+ || ctrl->aggr_corner.ceiling_volt > ctrl->aging_ref_volt) -+ return 0; -+ -+ for (i = 0, vreg_count = 0; i < ctrl->thread_count; i++) { -+ for (j = 0; j < ctrl->thread[i].vreg_count; j++) { -+ vreg = &ctrl->thread[i].vreg[j]; -+ vreg_count++; -+ -+ if (vreg->aging_allowed && vreg->vreg_enabled -+ && vreg->current_corner > vreg->aging_corner) -+ return 0; -+ } -+ } -+ -+ /* Verify that none of the aging sensors are currently masked. */ -+ for (i = 0; i < ctrl->aging_sensor_count; i++) { -+ id = ctrl->aging_sensor[i].sensor_id; -+ reg = cpr3_read(ctrl, CPR3_REG_SENSOR_MASK_READ(id)); -+ if (reg & BIT(id % 32)) -+ return 0; -+ } -+ -+ /* -+ * Verify that the aging possible register (if specified) has an -+ * acceptable value. -+ */ -+ if (ctrl->aging_possible_reg) { -+ reg = readl_relaxed(ctrl->aging_possible_reg); -+ reg &= ctrl->aging_possible_mask; -+ if (reg != ctrl->aging_possible_val) -+ return 0; -+ } -+ -+ restore_current_corner = kcalloc(vreg_count, -+ sizeof(*restore_current_corner), GFP_KERNEL); -+ restore_vreg_enabled = kcalloc(vreg_count, -+ sizeof(*restore_vreg_enabled), GFP_KERNEL); -+ if (!restore_current_corner || !restore_vreg_enabled) { -+ kfree(restore_current_corner); -+ kfree(restore_vreg_enabled); -+ return -ENOMEM; -+ } -+ -+ /* Force all regulators to the aging corner */ -+ for (i = 0, vreg_count = 0; i < ctrl->thread_count; i++) { -+ for (j = 0; j < ctrl->thread[i].vreg_count; j++, vreg_count++) { -+ vreg = &ctrl->thread[i].vreg[j]; -+ -+ restore_current_corner[vreg_count] -+ = vreg->current_corner; -+ restore_vreg_enabled[vreg_count] -+ = vreg->vreg_enabled; -+ -+ vreg->current_corner = vreg->aging_corner; -+ vreg->vreg_enabled = true; -+ } -+ } -+ -+ /* Force one of the regulators to require the aging reference voltage */ -+ vreg = &ctrl->thread[0].vreg[0]; -+ corner = &vreg->corner[vreg->current_corner]; -+ restore_aging_corner = *corner; -+ corner->ceiling_volt = ctrl->aging_ref_volt; -+ corner->floor_volt = ctrl->aging_ref_volt; -+ corner->open_loop_volt = ctrl->aging_ref_volt; -+ corner->last_volt = ctrl->aging_ref_volt; -+ -+ /* Skip last_volt caching */ -+ ctrl->last_corner_was_closed_loop = false; -+ -+ /* Set the vdd supply voltage to the aging reference voltage */ -+ rc = _cpr3_regulator_update_ctrl_state(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "unable to force vdd-supply to the aging reference voltage=%d uV, rc=%d\n", -+ ctrl->aging_ref_volt, rc); -+ goto cleanup; -+ } -+ -+ if (ctrl->aging_vdd_mode) { -+ rc = regulator_set_mode(ctrl->vdd_regulator, -+ ctrl->aging_vdd_mode); -+ if (rc) { -+ cpr3_err(ctrl, "unable to configure vdd-supply for mode=%u, rc=%d\n", -+ ctrl->aging_vdd_mode, rc); -+ goto cleanup; -+ } -+ } -+ -+ /* Perform aging measurement on all aging sensors */ -+ for (i = 0; i < ctrl->aging_sensor_count; i++) { -+ for (j = 0; j < CPR3_AGING_RETRY_COUNT; j++) { -+ rc = cpr3_regulator_measure_aging(ctrl, -+ &ctrl->aging_sensor[i]); -+ if (!rc) -+ break; -+ } -+ -+ if (!rc) { -+ aging_volt = -+ cpr3_voltage_adjustment( -+ ctrl->aging_sensor[i].ro_scale, -+ ctrl->aging_sensor[i].measured_quot_diff -+ - ctrl->aging_sensor[i].init_quot_diff); -+ max_aging_volt = max(max_aging_volt, aging_volt); -+ } else { -+ cpr3_err(ctrl, "CPR aging measurement failed after %d tries, rc=%d\n", -+ j, rc); -+ ctrl->aging_failed = true; -+ ctrl->aging_required = false; -+ goto cleanup; -+ } -+ } -+ -+cleanup: -+ vreg = &ctrl->thread[0].vreg[0]; -+ vreg->corner[vreg->current_corner] = restore_aging_corner; -+ -+ for (i = 0, vreg_count = 0; i < ctrl->thread_count; i++) { -+ for (j = 0; j < ctrl->thread[i].vreg_count; j++, vreg_count++) { -+ vreg = &ctrl->thread[i].vreg[j]; -+ vreg->current_corner -+ = restore_current_corner[vreg_count]; -+ vreg->vreg_enabled = restore_vreg_enabled[vreg_count]; -+ } -+ } -+ -+ kfree(restore_current_corner); -+ kfree(restore_vreg_enabled); -+ -+ /* Adjust the CPR target quotients according to the aging measurement */ -+ if (!rc) { -+ cpr3_regulator_set_aging_ref_adjustment(ctrl, max_aging_volt); -+ -+ cpr3_info(ctrl, "aging measurement successful; aging reference adjustment voltage=%d uV\n", -+ ctrl->aging_ref_adjust_volt); -+ ctrl->aging_succeeded = true; -+ ctrl->aging_required = false; -+ } -+ -+ if (ctrl->aging_complete_vdd_mode) { -+ rc = regulator_set_mode(ctrl->vdd_regulator, -+ ctrl->aging_complete_vdd_mode); -+ if (rc) -+ cpr3_err(ctrl, "unable to configure vdd-supply for mode=%u, rc=%d\n", -+ ctrl->aging_complete_vdd_mode, rc); -+ } -+ -+ /* Skip last_volt caching */ -+ ctrl->last_corner_was_closed_loop = false; -+ -+ /* -+ * Restore vdd-supply to the voltage before the aging measurement and -+ * restore the CPR3 controller hardware state. -+ */ -+ rc2 = _cpr3_regulator_update_ctrl_state(ctrl); -+ -+ /* Stop last_volt caching on for the next request */ -+ ctrl->last_corner_was_closed_loop = false; -+ -+ return rc ? rc : rc2; -+} -+ -+/** -+ * cpr3_regulator_update_ctrl_state() - update the state of the CPR controller -+ * to reflect the corners used by all CPR3 regulators as well as -+ * the CPR operating mode and perform aging adjustments if needed -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Note, CPR3 controller lock must be held by the caller. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_regulator_update_ctrl_state(struct cpr3_controller *ctrl) -+{ -+ int rc; -+ -+ rc = _cpr3_regulator_update_ctrl_state(ctrl); -+ if (rc) -+ return rc; -+ -+ return cpr3_regulator_aging_adjust(ctrl); -+} -+ -+/** -+ * cpr3_regulator_set_voltage() - set the voltage corner for the CPR3 regulator -+ * associated with the regulator device -+ * @rdev: Regulator device pointer for the cpr3-regulator -+ * @corner: New voltage corner to set (offset by CPR3_CORNER_OFFSET) -+ * @corner_max: Maximum voltage corner allowed (offset by -+ * CPR3_CORNER_OFFSET) -+ * @selector: Pointer which is filled with the selector value for the -+ * corner -+ * -+ * This function is passed as a callback function into the regulator ops that -+ * are registered for each cpr3-regulator device. The VDD voltage will not be -+ * physically configured until both this function and cpr3_regulator_enable() -+ * are called. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_regulator_set_voltage(struct regulator_dev *rdev, -+ int corner, int corner_max, unsigned *selector) -+{ -+ struct cpr3_regulator *vreg = rdev_get_drvdata(rdev); -+ struct cpr3_controller *ctrl = vreg->thread->ctrl; -+ int rc = 0; -+ int last_corner; -+ -+ corner -= CPR3_CORNER_OFFSET; -+ corner_max -= CPR3_CORNER_OFFSET; -+ *selector = corner; -+ -+ mutex_lock(&ctrl->lock); -+ -+ if (!vreg->vreg_enabled) { -+ vreg->current_corner = corner; -+ cpr3_debug(vreg, "stored corner=%d\n", corner); -+ goto done; -+ } else if (vreg->current_corner == corner) { -+ goto done; -+ } -+ -+ last_corner = vreg->current_corner; -+ vreg->current_corner = corner; -+ -+ if (vreg->cpr4_regulator_data != NULL) -+ if (vreg->cpr4_regulator_data->mem_acc_funcs != NULL) -+ vreg->cpr4_regulator_data->mem_acc_funcs->set_mem_acc(rdev); -+ -+ rc = cpr3_regulator_update_ctrl_state(ctrl); -+ if (rc) { -+ cpr3_err(vreg, "could not update CPR state, rc=%d\n", rc); -+ vreg->current_corner = last_corner; -+ } -+ -+ if (vreg->cpr4_regulator_data != NULL) -+ if (vreg->cpr4_regulator_data->mem_acc_funcs != NULL) -+ vreg->cpr4_regulator_data->mem_acc_funcs->clear_mem_acc(rdev); -+ -+ cpr3_debug(vreg, "set corner=%d\n", corner); -+done: -+ mutex_unlock(&ctrl->lock); -+ -+ return rc; -+} -+ -+/** -+ * cpr3_handle_temp_open_loop_adjustment() - voltage based cold temperature -+ * -+ * @rdev: Regulator device pointer for the cpr3-regulator -+ * @is_cold: Flag to denote enter/exit cold condition -+ * -+ * This function is adjusts voltage margin based on cold condition -+ * -+ * Return: 0 = success -+ */ -+ -+int cpr3_handle_temp_open_loop_adjustment(struct cpr3_controller *ctrl, -+ bool is_cold) -+{ -+ int i ,j, k, rc; -+ struct cpr3_regulator *vreg; -+ -+ mutex_lock(&ctrl->lock); -+ for (i = 0; i < ctrl->thread_count; i++) { -+ for (j = 0; j < ctrl->thread[i].vreg_count; j++) { -+ vreg = &ctrl->thread[i].vreg[j]; -+ for (k = 0; k < vreg->corner_count; k++) { -+ vreg->corner[k].open_loop_volt = is_cold ? -+ vreg->corner[k].cold_temp_open_loop_volt : -+ vreg->corner[k].normal_temp_open_loop_volt; -+ } -+ } -+ } -+ rc = cpr3_regulator_update_ctrl_state(ctrl); -+ mutex_unlock(&ctrl->lock); -+ -+ return rc; -+} -+ -+/** -+ * cpr3_regulator_get_voltage() - get the voltage corner for the CPR3 regulator -+ * associated with the regulator device -+ * @rdev: Regulator device pointer for the cpr3-regulator -+ * -+ * This function is passed as a callback function into the regulator ops that -+ * are registered for each cpr3-regulator device. -+ * -+ * Return: voltage corner value offset by CPR3_CORNER_OFFSET -+ */ -+static int cpr3_regulator_get_voltage(struct regulator_dev *rdev) -+{ -+ struct cpr3_regulator *vreg = rdev_get_drvdata(rdev); -+ -+ if (vreg->current_corner == CPR3_REGULATOR_CORNER_INVALID) -+ return CPR3_CORNER_OFFSET; -+ else -+ return vreg->current_corner + CPR3_CORNER_OFFSET; -+} -+ -+/** -+ * cpr3_regulator_list_voltage() - return the voltage corner mapped to the -+ * specified selector -+ * @rdev: Regulator device pointer for the cpr3-regulator -+ * @selector: Regulator selector -+ * -+ * This function is passed as a callback function into the regulator ops that -+ * are registered for each cpr3-regulator device. -+ * -+ * Return: voltage corner value offset by CPR3_CORNER_OFFSET -+ */ -+static int cpr3_regulator_list_voltage(struct regulator_dev *rdev, -+ unsigned selector) -+{ -+ struct cpr3_regulator *vreg = rdev_get_drvdata(rdev); -+ -+ if (selector < vreg->corner_count) -+ return selector + CPR3_CORNER_OFFSET; -+ else -+ return 0; -+} -+ -+/** -+ * cpr3_regulator_is_enabled() - return the enable state of the CPR3 regulator -+ * @rdev: Regulator device pointer for the cpr3-regulator -+ * -+ * This function is passed as a callback function into the regulator ops that -+ * are registered for each cpr3-regulator device. -+ * -+ * Return: true if regulator is enabled, false if regulator is disabled -+ */ -+static int cpr3_regulator_is_enabled(struct regulator_dev *rdev) -+{ -+ struct cpr3_regulator *vreg = rdev_get_drvdata(rdev); -+ -+ return vreg->vreg_enabled; -+} -+ -+/** -+ * cpr3_regulator_enable() - enable the CPR3 regulator -+ * @rdev: Regulator device pointer for the cpr3-regulator -+ * -+ * This function is passed as a callback function into the regulator ops that -+ * are registered for each cpr3-regulator device. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_regulator_enable(struct regulator_dev *rdev) -+{ -+ struct cpr3_regulator *vreg = rdev_get_drvdata(rdev); -+ struct cpr3_controller *ctrl = vreg->thread->ctrl; -+ int rc = 0; -+ -+ if (vreg->vreg_enabled == true) -+ return 0; -+ -+ mutex_lock(&ctrl->lock); -+ -+ if (ctrl->system_regulator) { -+ rc = regulator_enable(ctrl->system_regulator); -+ if (rc) { -+ cpr3_err(ctrl, "regulator_enable(system) failed, rc=%d\n", -+ rc); -+ goto done; -+ } -+ } -+ -+ rc = regulator_enable(ctrl->vdd_regulator); -+ if (rc) { -+ cpr3_err(vreg, "regulator_enable(vdd) failed, rc=%d\n", rc); -+ goto done; -+ } -+ -+ vreg->vreg_enabled = true; -+ rc = cpr3_regulator_update_ctrl_state(ctrl); -+ if (rc) { -+ cpr3_err(vreg, "could not update CPR state, rc=%d\n", rc); -+ regulator_disable(ctrl->vdd_regulator); -+ vreg->vreg_enabled = false; -+ goto done; -+ } -+ -+ cpr3_debug(vreg, "Enabled\n"); -+done: -+ mutex_unlock(&ctrl->lock); -+ -+ return rc; -+} -+ -+/** -+ * cpr3_regulator_disable() - disable the CPR3 regulator -+ * @rdev: Regulator device pointer for the cpr3-regulator -+ * -+ * This function is passed as a callback function into the regulator ops that -+ * are registered for each cpr3-regulator device. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_regulator_disable(struct regulator_dev *rdev) -+{ -+ struct cpr3_regulator *vreg = rdev_get_drvdata(rdev); -+ struct cpr3_controller *ctrl = vreg->thread->ctrl; -+ int rc, rc2; -+ -+ if (vreg->vreg_enabled == false) -+ return 0; -+ -+ mutex_lock(&ctrl->lock); -+ rc = regulator_disable(ctrl->vdd_regulator); -+ if (rc) { -+ cpr3_err(vreg, "regulator_disable(vdd) failed, rc=%d\n", rc); -+ goto done; -+ } -+ -+ vreg->vreg_enabled = false; -+ rc = cpr3_regulator_update_ctrl_state(ctrl); -+ if (rc) { -+ cpr3_err(vreg, "could not update CPR state, rc=%d\n", rc); -+ rc2 = regulator_enable(ctrl->vdd_regulator); -+ vreg->vreg_enabled = true; -+ goto done; -+ } -+ -+ if (ctrl->system_regulator) { -+ rc = regulator_disable(ctrl->system_regulator); -+ if (rc) { -+ cpr3_err(ctrl, "regulator_disable(system) failed, rc=%d\n", -+ rc); -+ goto done; -+ } -+ } -+ -+ cpr3_debug(vreg, "Disabled\n"); -+done: -+ mutex_unlock(&ctrl->lock); -+ -+ return rc; -+} -+ -+static struct regulator_ops cpr3_regulator_ops = { -+ .enable = cpr3_regulator_enable, -+ .disable = cpr3_regulator_disable, -+ .is_enabled = cpr3_regulator_is_enabled, -+ .set_voltage = cpr3_regulator_set_voltage, -+ .get_voltage = cpr3_regulator_get_voltage, -+ .list_voltage = cpr3_regulator_list_voltage, -+}; -+ -+/** -+ * cpr3_print_result() - print CPR measurement results to the kernel log for -+ * debugging purposes -+ * @thread: Pointer to the CPR3 thread -+ * -+ * Return: None -+ */ -+static void cpr3_print_result(struct cpr3_thread *thread) -+{ -+ struct cpr3_controller *ctrl = thread->ctrl; -+ u32 result[3], busy, step_dn, step_up, error_steps, error, negative; -+ u32 quot_min, quot_max, ro_min, ro_max, step_quot_min, step_quot_max; -+ u32 sensor_min, sensor_max; -+ char *sign; -+ -+ result[0] = cpr3_read(ctrl, CPR3_REG_RESULT0(thread->thread_id)); -+ result[1] = cpr3_read(ctrl, CPR3_REG_RESULT1(thread->thread_id)); -+ result[2] = cpr3_read(ctrl, CPR3_REG_RESULT2(thread->thread_id)); -+ -+ busy = !!(result[0] & CPR3_RESULT0_BUSY_MASK); -+ step_dn = !!(result[0] & CPR3_RESULT0_STEP_DN_MASK); -+ step_up = !!(result[0] & CPR3_RESULT0_STEP_UP_MASK); -+ error_steps = (result[0] & CPR3_RESULT0_ERROR_STEPS_MASK) -+ >> CPR3_RESULT0_ERROR_STEPS_SHIFT; -+ error = (result[0] & CPR3_RESULT0_ERROR_MASK) -+ >> CPR3_RESULT0_ERROR_SHIFT; -+ negative = !!(result[0] & CPR3_RESULT0_NEGATIVE_MASK); -+ -+ quot_min = (result[1] & CPR3_RESULT1_QUOT_MIN_MASK) -+ >> CPR3_RESULT1_QUOT_MIN_SHIFT; -+ quot_max = (result[1] & CPR3_RESULT1_QUOT_MAX_MASK) -+ >> CPR3_RESULT1_QUOT_MAX_SHIFT; -+ ro_min = (result[1] & CPR3_RESULT1_RO_MIN_MASK) -+ >> CPR3_RESULT1_RO_MIN_SHIFT; -+ ro_max = (result[1] & CPR3_RESULT1_RO_MAX_MASK) -+ >> CPR3_RESULT1_RO_MAX_SHIFT; -+ -+ step_quot_min = (result[2] & CPR3_RESULT2_STEP_QUOT_MIN_MASK) -+ >> CPR3_RESULT2_STEP_QUOT_MIN_SHIFT; -+ step_quot_max = (result[2] & CPR3_RESULT2_STEP_QUOT_MAX_MASK) -+ >> CPR3_RESULT2_STEP_QUOT_MAX_SHIFT; -+ sensor_min = (result[2] & CPR3_RESULT2_SENSOR_MIN_MASK) -+ >> CPR3_RESULT2_SENSOR_MIN_SHIFT; -+ sensor_max = (result[2] & CPR3_RESULT2_SENSOR_MAX_MASK) -+ >> CPR3_RESULT2_SENSOR_MAX_SHIFT; -+ -+ sign = negative ? "-" : ""; -+ cpr3_debug(ctrl, "thread %u: busy=%u, step_dn=%u, step_up=%u, error_steps=%s%u, error=%s%u\n", -+ thread->thread_id, busy, step_dn, step_up, sign, error_steps, -+ sign, error); -+ cpr3_debug(ctrl, "thread %u: quot_min=%u, quot_max=%u, ro_min=%u, ro_max=%u\n", -+ thread->thread_id, quot_min, quot_max, ro_min, ro_max); -+ cpr3_debug(ctrl, "thread %u: step_quot_min=%u, step_quot_max=%u, sensor_min=%u, sensor_max=%u\n", -+ thread->thread_id, step_quot_min, step_quot_max, sensor_min, -+ sensor_max); -+} -+ -+/** -+ * cpr3_thread_busy() - returns if the specified CPR3 thread is busy taking -+ * a measurement -+ * @thread: Pointer to the CPR3 thread -+ * -+ * Return: CPR3 busy status -+ */ -+static bool cpr3_thread_busy(struct cpr3_thread *thread) -+{ -+ u32 result; -+ -+ result = cpr3_read(thread->ctrl, CPR3_REG_RESULT0(thread->thread_id)); -+ -+ return !!(result & CPR3_RESULT0_BUSY_MASK); -+} -+ -+/** -+ * cpr3_irq_handler() - CPR interrupt handler callback function used for -+ * software closed-loop operation -+ * @irq: CPR interrupt number -+ * @data: Private data corresponding to the CPR3 controller -+ * pointer -+ * -+ * This function increases or decreases the vdd supply voltage based upon the -+ * CPR controller recommendation. -+ * -+ * Return: IRQ_HANDLED -+ */ -+static irqreturn_t cpr3_irq_handler(int irq, void *data) -+{ -+ struct cpr3_controller *ctrl = data; -+ struct cpr3_corner *aggr = &ctrl->aggr_corner; -+ u32 cont = CPR3_CONT_CMD_NACK; -+ u32 reg_last_measurement = 0; -+ struct cpr3_regulator *vreg; -+ struct cpr3_corner *corner; -+ unsigned long flags; -+ int i, j, new_volt, last_volt, dynamic_floor_volt, rc; -+ u32 irq_en, status, cpr_status, ctl; -+ bool up, down; -+ -+ mutex_lock(&ctrl->lock); -+ -+ if (!ctrl->cpr_enabled) { -+ cpr3_debug(ctrl, "CPR interrupt received but CPR is disabled\n"); -+ mutex_unlock(&ctrl->lock); -+ return IRQ_HANDLED; -+ } else if (ctrl->use_hw_closed_loop) { -+ cpr3_debug(ctrl, "CPR interrupt received but CPR is using HW closed-loop\n"); -+ goto done; -+ } -+ -+ /* -+ * CPR IRQ status checking and CPR controller disabling must happen -+ * atomically and without invening delay in order to avoid an interrupt -+ * storm caused by the handler racing with the CPR controller. -+ */ -+ local_irq_save(flags); -+ preempt_disable(); -+ -+ status = cpr3_read(ctrl, CPR3_REG_IRQ_STATUS); -+ up = status & CPR3_IRQ_UP; -+ down = status & CPR3_IRQ_DOWN; -+ -+ if (!up && !down) { -+ /* -+ * Toggle the CPR controller off and then back on since the -+ * hardware and software states are out of sync. This condition -+ * occurs after an aging measurement completes as the CPR IRQ -+ * physically triggers during the aging measurement but the -+ * handler is stuck waiting on the mutex lock. -+ */ -+ cpr3_ctrl_loop_disable(ctrl); -+ -+ local_irq_restore(flags); -+ preempt_enable(); -+ -+ /* Wait for the loop disable write to complete */ -+ mb(); -+ -+ /* Wait for BUSY=1 and LOOP_EN=0 in CPR controller registers. */ -+ for (i = 0; i < CPR3_REGISTER_WRITE_DELAY_US / 10; i++) { -+ cpr_status = cpr3_read(ctrl, CPR3_REG_CPR_STATUS); -+ ctl = cpr3_read(ctrl, CPR3_REG_CPR_CTL); -+ if (cpr_status & CPR3_CPR_STATUS_BUSY_MASK -+ && (ctl & CPR3_CPR_CTL_LOOP_EN_MASK) -+ == CPR3_CPR_CTL_LOOP_DISABLE) -+ break; -+ udelay(10); -+ } -+ if (i == CPR3_REGISTER_WRITE_DELAY_US / 10) -+ cpr3_debug(ctrl, "CPR controller not disabled after %d us\n", -+ CPR3_REGISTER_WRITE_DELAY_US); -+ -+ /* Clear interrupt status */ -+ cpr3_write(ctrl, CPR3_REG_IRQ_CLEAR, -+ CPR3_IRQ_UP | CPR3_IRQ_DOWN); -+ -+ /* Wait for the interrupt clearing write to complete */ -+ mb(); -+ -+ /* Wait for IRQ_STATUS register to be cleared. */ -+ for (i = 0; i < CPR3_REGISTER_WRITE_DELAY_US / 10; i++) { -+ status = cpr3_read(ctrl, CPR3_REG_IRQ_STATUS); -+ if (!(status & (CPR3_IRQ_UP | CPR3_IRQ_DOWN))) -+ break; -+ udelay(10); -+ } -+ if (i == CPR3_REGISTER_WRITE_DELAY_US / 10) -+ cpr3_debug(ctrl, "CPR interrupts not cleared after %d us\n", -+ CPR3_REGISTER_WRITE_DELAY_US); -+ -+ cpr3_ctrl_loop_enable(ctrl); -+ -+ cpr3_debug(ctrl, "CPR interrupt received but no up or down status bit is set\n"); -+ -+ mutex_unlock(&ctrl->lock); -+ return IRQ_HANDLED; -+ } else if (up && down) { -+ cpr3_debug(ctrl, "both up and down status bits set\n"); -+ /* The up flag takes precedence over the down flag. */ -+ down = false; -+ } -+ -+ if (ctrl->supports_hw_closed_loop) -+ reg_last_measurement -+ = cpr3_read(ctrl, CPR3_REG_LAST_MEASUREMENT); -+ dynamic_floor_volt = cpr3_regulator_get_dynamic_floor_volt(ctrl, -+ reg_last_measurement); -+ -+ local_irq_restore(flags); -+ preempt_enable(); -+ -+ irq_en = aggr->irq_en; -+ last_volt = aggr->last_volt; -+ -+ for (i = 0; i < ctrl->thread_count; i++) { -+ if (cpr3_thread_busy(&ctrl->thread[i])) { -+ cpr3_debug(ctrl, "CPR thread %u busy when it should be waiting for SW cont\n", -+ ctrl->thread[i].thread_id); -+ goto done; -+ } -+ } -+ -+ new_volt = up ? last_volt + ctrl->step_volt -+ : last_volt - ctrl->step_volt; -+ -+ /* Re-enable UP/DOWN interrupt when its opposite is received. */ -+ irq_en |= up ? CPR3_IRQ_DOWN : CPR3_IRQ_UP; -+ -+ if (new_volt > aggr->ceiling_volt) { -+ new_volt = aggr->ceiling_volt; -+ irq_en &= ~CPR3_IRQ_UP; -+ cpr3_debug(ctrl, "limiting to ceiling=%d uV\n", -+ aggr->ceiling_volt); -+ } else if (new_volt < aggr->floor_volt) { -+ new_volt = aggr->floor_volt; -+ irq_en &= ~CPR3_IRQ_DOWN; -+ cpr3_debug(ctrl, "limiting to floor=%d uV\n", aggr->floor_volt); -+ } -+ -+ if (down && new_volt < dynamic_floor_volt) { -+ /* -+ * The vdd-supply voltage should not be decreased below the -+ * dynamic floor voltage. However, it is not necessary (and -+ * counter productive) to force the voltage up to this level -+ * if it happened to be below it since the closed-loop voltage -+ * must have gotten there in a safe manner while the power -+ * domains for the CPR3 regulator imposing the dynamic floor -+ * were not bypassed. -+ */ -+ new_volt = last_volt; -+ irq_en &= ~CPR3_IRQ_DOWN; -+ cpr3_debug(ctrl, "limiting to dynamic floor=%d uV\n", -+ dynamic_floor_volt); -+ } -+ -+ for (i = 0; i < ctrl->thread_count; i++) -+ cpr3_print_result(&ctrl->thread[i]); -+ -+ cpr3_debug(ctrl, "%s: new_volt=%d uV, last_volt=%d uV\n", -+ up ? "UP" : "DN", new_volt, last_volt); -+ -+ if (ctrl->proc_clock_throttle && last_volt == aggr->ceiling_volt -+ && new_volt < last_volt) -+ cpr3_write(ctrl, CPR3_REG_PD_THROTTLE, -+ ctrl->proc_clock_throttle); -+ -+ if (new_volt != last_volt) { -+ rc = cpr3_regulator_scale_vdd_voltage(ctrl, new_volt, -+ last_volt, -+ aggr); -+ if (rc) { -+ cpr3_err(ctrl, "scale_vdd() failed to set vdd=%d uV, rc=%d\n", -+ new_volt, rc); -+ goto done; -+ } -+ cont = CPR3_CONT_CMD_ACK; -+ -+ /* -+ * Update the closed-loop voltage for all regulators managed -+ * by this CPR controller. -+ */ -+ for (i = 0; i < ctrl->thread_count; i++) { -+ for (j = 0; j < ctrl->thread[i].vreg_count; j++) { -+ vreg = &ctrl->thread[i].vreg[j]; -+ cpr3_update_vreg_closed_loop_volt(vreg, -+ new_volt, reg_last_measurement); -+ } -+ } -+ } -+ -+ if (ctrl->proc_clock_throttle && new_volt == aggr->ceiling_volt) -+ cpr3_write(ctrl, CPR3_REG_PD_THROTTLE, -+ CPR3_PD_THROTTLE_DISABLE); -+ -+ corner = &ctrl->thread[0].vreg[0].corner[ -+ ctrl->thread[0].vreg[0].current_corner]; -+ -+ if (irq_en != aggr->irq_en) { -+ aggr->irq_en = irq_en; -+ cpr3_write(ctrl, CPR3_REG_IRQ_EN, irq_en); -+ } -+ -+ aggr->last_volt = new_volt; -+ -+done: -+ /* Clear interrupt status */ -+ cpr3_write(ctrl, CPR3_REG_IRQ_CLEAR, CPR3_IRQ_UP | CPR3_IRQ_DOWN); -+ -+ /* ACK or NACK the CPR controller */ -+ cpr3_write(ctrl, CPR3_REG_CONT_CMD, cont); -+ -+ mutex_unlock(&ctrl->lock); -+ return IRQ_HANDLED; -+} -+ -+/** -+ * cpr3_ceiling_irq_handler() - CPR ceiling reached interrupt handler callback -+ * function used for hardware closed-loop operation -+ * @irq: CPR ceiling interrupt number -+ * @data: Private data corresponding to the CPR3 controller -+ * pointer -+ * -+ * This function disables processor clock throttling and closed-loop operation -+ * when the ceiling voltage is reached. -+ * -+ * Return: IRQ_HANDLED -+ */ -+static irqreturn_t cpr3_ceiling_irq_handler(int irq, void *data) -+{ -+ struct cpr3_controller *ctrl = data; -+ int volt; -+ -+ mutex_lock(&ctrl->lock); -+ -+ if (!ctrl->cpr_enabled) { -+ cpr3_debug(ctrl, "CPR ceiling interrupt received but CPR is disabled\n"); -+ goto done; -+ } else if (!ctrl->use_hw_closed_loop) { -+ cpr3_debug(ctrl, "CPR ceiling interrupt received but CPR is using SW closed-loop\n"); -+ goto done; -+ } -+ -+ volt = regulator_get_voltage(ctrl->vdd_regulator); -+ if (volt < 0) { -+ cpr3_err(ctrl, "could not get vdd voltage, rc=%d\n", volt); -+ goto done; -+ } else if (volt != ctrl->aggr_corner.ceiling_volt) { -+ cpr3_debug(ctrl, "CPR ceiling interrupt received but vdd voltage: %d uV != ceiling voltage: %d uV\n", -+ volt, ctrl->aggr_corner.ceiling_volt); -+ goto done; -+ } -+ -+ if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR3) { -+ /* -+ * Since the ceiling voltage has been reached, disable processor -+ * clock throttling as well as CPR closed-loop operation. -+ */ -+ cpr3_write(ctrl, CPR3_REG_PD_THROTTLE, -+ CPR3_PD_THROTTLE_DISABLE); -+ cpr3_ctrl_loop_disable(ctrl); -+ cpr3_debug(ctrl, "CPR closed-loop and throttling disabled\n"); -+ } -+ -+done: -+ mutex_unlock(&ctrl->lock); -+ return IRQ_HANDLED; -+} -+ -+/** -+ * cpr3_regulator_vreg_register() - register a regulator device for a CPR3 -+ * regulator -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * This function initializes all regulator framework related structures and then -+ * calls regulator_register() for the CPR3 regulator. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_regulator_vreg_register(struct cpr3_regulator *vreg) -+{ -+ struct regulator_config config = {}; -+ struct regulator_desc *rdesc; -+ struct regulator_init_data *init_data; -+ int rc; -+ -+ init_data = of_get_regulator_init_data(vreg->thread->ctrl->dev, -+ vreg->of_node, &vreg->rdesc); -+ if (!init_data) { -+ cpr3_err(vreg, "regulator init data is missing\n"); -+ return -EINVAL; -+ } -+ -+ init_data->constraints.input_uV = init_data->constraints.max_uV; -+ rdesc = &vreg->rdesc; -+ init_data->constraints.valid_ops_mask |= -+ REGULATOR_CHANGE_VOLTAGE | REGULATOR_CHANGE_STATUS; -+ rdesc->ops = &cpr3_regulator_ops; -+ -+ rdesc->n_voltages = vreg->corner_count; -+ rdesc->name = init_data->constraints.name; -+ rdesc->owner = THIS_MODULE; -+ rdesc->type = REGULATOR_VOLTAGE; -+ -+ config.dev = vreg->thread->ctrl->dev; -+ config.driver_data = vreg; -+ config.init_data = init_data; -+ config.of_node = vreg->of_node; -+ -+ vreg->rdev = regulator_register(vreg->thread->ctrl->dev, rdesc, &config); -+ if (IS_ERR(vreg->rdev)) { -+ rc = PTR_ERR(vreg->rdev); -+ cpr3_err(vreg, "regulator_register failed, rc=%d\n", rc); -+ return rc; -+ } -+ -+ return 0; -+} -+ -+static int debugfs_int_set(void *data, u64 val) -+{ -+ *(int *)data = val; -+ return 0; -+} -+ -+static int debugfs_int_get(void *data, u64 *val) -+{ -+ *val = *(int *)data; -+ return 0; -+} -+DEFINE_SIMPLE_ATTRIBUTE(fops_int, debugfs_int_get, debugfs_int_set, "%lld\n"); -+DEFINE_SIMPLE_ATTRIBUTE(fops_int_ro, debugfs_int_get, NULL, "%lld\n"); -+DEFINE_SIMPLE_ATTRIBUTE(fops_int_wo, NULL, debugfs_int_set, "%lld\n"); -+ -+/** -+ * debugfs_create_int - create a debugfs file that is used to read and write a -+ * signed int value -+ * @name: Pointer to a string containing the name of the file to -+ * create -+ * @mode: The permissions that the file should have -+ * @parent: Pointer to the parent dentry for this file. This should -+ * be a directory dentry if set. If this parameter is -+ * %NULL, then the file will be created in the root of the -+ * debugfs filesystem. -+ * @value: Pointer to the variable that the file should read to and -+ * write from -+ * -+ * This function creates a file in debugfs with the given name that -+ * contains the value of the variable @value. If the @mode variable is so -+ * set, it can be read from, and written to. -+ * -+ * This function will return a pointer to a dentry if it succeeds. This -+ * pointer must be passed to the debugfs_remove() function when the file is -+ * to be removed. If an error occurs, %NULL will be returned. -+ */ -+static struct dentry *debugfs_create_int(const char *name, umode_t mode, -+ struct dentry *parent, int *value) -+{ -+ /* if there are no write bits set, make read only */ -+ if (!(mode & S_IWUGO)) -+ return debugfs_create_file(name, mode, parent, value, -+ &fops_int_ro); -+ /* if there are no read bits set, make write only */ -+ if (!(mode & S_IRUGO)) -+ return debugfs_create_file(name, mode, parent, value, -+ &fops_int_wo); -+ -+ return debugfs_create_file(name, mode, parent, value, &fops_int); -+} -+ -+static int debugfs_bool_get(void *data, u64 *val) -+{ -+ *val = *(bool *)data; -+ return 0; -+} -+DEFINE_SIMPLE_ATTRIBUTE(fops_bool_ro, debugfs_bool_get, NULL, "%lld\n"); -+ -+/** -+ * struct cpr3_debug_corner_info - data structure used by the -+ * cpr3_debugfs_create_corner_int function -+ * @vreg: Pointer to the CPR3 regulator -+ * @index: Pointer to the corner array index -+ * @member_offset: Offset in bytes from the beginning of struct cpr3_corner -+ * to the beginning of the value to be read from -+ * @corner: Pointer to the CPR3 corner array -+ */ -+struct cpr3_debug_corner_info { -+ struct cpr3_regulator *vreg; -+ int *index; -+ size_t member_offset; -+ struct cpr3_corner *corner; -+}; -+ -+static int cpr3_debug_corner_int_get(void *data, u64 *val) -+{ -+ struct cpr3_debug_corner_info *info = data; -+ struct cpr3_controller *ctrl = info->vreg->thread->ctrl; -+ int i; -+ -+ mutex_lock(&ctrl->lock); -+ -+ i = *info->index; -+ if (i < 0) -+ i = 0; -+ -+ *val = *(int *)((char *)&info->vreg->corner[i] + info->member_offset); -+ -+ mutex_unlock(&ctrl->lock); -+ -+ return 0; -+} -+DEFINE_SIMPLE_ATTRIBUTE(cpr3_debug_corner_int_fops, cpr3_debug_corner_int_get, -+ NULL, "%lld\n"); -+ -+/** -+ * cpr3_debugfs_create_corner_int - create a debugfs file that is used to read -+ * a signed int value out of a CPR3 regulator's corner array -+ * @vreg: Pointer to the CPR3 regulator -+ * @name: Pointer to a string containing the name of the file to -+ * create -+ * @mode: The permissions that the file should have -+ * @parent: Pointer to the parent dentry for this file. This should -+ * be a directory dentry if set. If this parameter is -+ * %NULL, then the file will be created in the root of the -+ * debugfs filesystem. -+ * @index: Pointer to the corner array index -+ * @member_offset: Offset in bytes from the beginning of struct cpr3_corner -+ * to the beginning of the value to be read from -+ * -+ * This function creates a file in debugfs with the given name that -+ * contains the value of the int type variable vreg->corner[index].member -+ * where member_offset == offsetof(struct cpr3_corner, member). -+ */ -+static struct dentry *cpr3_debugfs_create_corner_int( -+ struct cpr3_regulator *vreg, const char *name, umode_t mode, -+ struct dentry *parent, int *index, size_t member_offset) -+{ -+ struct cpr3_debug_corner_info *info; -+ -+ info = devm_kzalloc(vreg->thread->ctrl->dev, sizeof(*info), GFP_KERNEL); -+ if (!info) -+ return NULL; -+ -+ info->vreg = vreg; -+ info->index = index; -+ info->member_offset = member_offset; -+ -+ return debugfs_create_file(name, mode, parent, info, -+ &cpr3_debug_corner_int_fops); -+} -+ -+static int cpr3_debug_quot_open(struct inode *inode, struct file *file) -+{ -+ struct cpr3_debug_corner_info *info = inode->i_private; -+ struct cpr3_thread *thread = info->vreg->thread; -+ int size, i, pos; -+ u32 *quot; -+ char *buf; -+ -+ /* -+ * Max size: -+ * - 10 digits + ' ' or '\n' = 11 bytes per number -+ * - terminating '\0' -+ */ -+ size = CPR3_RO_COUNT * 11; -+ buf = kzalloc(size + 1, GFP_KERNEL); -+ if (!buf) -+ return -ENOMEM; -+ -+ file->private_data = buf; -+ -+ mutex_lock(&thread->ctrl->lock); -+ -+ quot = info->corner[*info->index].target_quot; -+ -+ for (i = 0, pos = 0; i < CPR3_RO_COUNT; i++) -+ pos += scnprintf(buf + pos, size - pos, "%u%c", -+ quot[i], i < CPR3_RO_COUNT - 1 ? ' ' : '\n'); -+ -+ mutex_unlock(&thread->ctrl->lock); -+ -+ return nonseekable_open(inode, file); -+} -+ -+static ssize_t cpr3_debug_quot_read(struct file *file, char __user *buf, -+ size_t len, loff_t *ppos) -+{ -+ return simple_read_from_buffer(buf, len, ppos, file->private_data, -+ strlen(file->private_data)); -+} -+ -+static int cpr3_debug_quot_release(struct inode *inode, struct file *file) -+{ -+ kfree(file->private_data); -+ -+ return 0; -+} -+ -+static const struct file_operations cpr3_debug_quot_fops = { -+ .owner = THIS_MODULE, -+ .open = cpr3_debug_quot_open, -+ .release = cpr3_debug_quot_release, -+ .read = cpr3_debug_quot_read, -+}; -+ -+/** -+ * cpr3_regulator_debugfs_corner_add() - add debugfs files to expose -+ * configuration data for the CPR corner -+ * @vreg: Pointer to the CPR3 regulator -+ * @corner_dir: Pointer to the parent corner dentry for the new files -+ * @index: Pointer to the corner array index -+ * -+ * Return: none -+ */ -+static void cpr3_regulator_debugfs_corner_add(struct cpr3_regulator *vreg, -+ struct dentry *corner_dir, int *index) -+{ -+ struct cpr3_debug_corner_info *info; -+ struct dentry *temp; -+ -+ temp = cpr3_debugfs_create_corner_int(vreg, "floor_volt", S_IRUGO, -+ corner_dir, index, offsetof(struct cpr3_corner, floor_volt)); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(vreg, "floor_volt debugfs file creation failed\n"); -+ return; -+ } -+ -+ temp = cpr3_debugfs_create_corner_int(vreg, "ceiling_volt", S_IRUGO, -+ corner_dir, index, offsetof(struct cpr3_corner, ceiling_volt)); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(vreg, "ceiling_volt debugfs file creation failed\n"); -+ return; -+ } -+ -+ temp = cpr3_debugfs_create_corner_int(vreg, "open_loop_volt", S_IRUGO, -+ corner_dir, index, -+ offsetof(struct cpr3_corner, open_loop_volt)); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(vreg, "open_loop_volt debugfs file creation failed\n"); -+ return; -+ } -+ -+ temp = cpr3_debugfs_create_corner_int(vreg, "last_volt", S_IRUGO, -+ corner_dir, index, offsetof(struct cpr3_corner, last_volt)); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(vreg, "last_volt debugfs file creation failed\n"); -+ return; -+ } -+ -+ info = devm_kzalloc(vreg->thread->ctrl->dev, sizeof(*info), GFP_KERNEL); -+ if (!info) -+ return; -+ -+ info->vreg = vreg; -+ info->index = index; -+ info->corner = vreg->corner; -+ -+ temp = debugfs_create_file("target_quots", S_IRUGO, corner_dir, -+ info, &cpr3_debug_quot_fops); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(vreg, "target_quots debugfs file creation failed\n"); -+ return; -+ } -+} -+ -+/** -+ * cpr3_debug_corner_index_set() - debugfs callback used to change the -+ * value of the CPR3 regulator debug_corner index -+ * @data: Pointer to private data which is equal to the CPR3 -+ * regulator pointer -+ * @val: New value for debug_corner -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_debug_corner_index_set(void *data, u64 val) -+{ -+ struct cpr3_regulator *vreg = data; -+ -+ if (val < CPR3_CORNER_OFFSET || val > vreg->corner_count) { -+ cpr3_err(vreg, "invalid corner index %llu; allowed values: %d-%d\n", -+ val, CPR3_CORNER_OFFSET, vreg->corner_count); -+ return -EINVAL; -+ } -+ -+ mutex_lock(&vreg->thread->ctrl->lock); -+ vreg->debug_corner = val - CPR3_CORNER_OFFSET; -+ mutex_unlock(&vreg->thread->ctrl->lock); -+ -+ return 0; -+} -+ -+/** -+ * cpr3_debug_corner_index_get() - debugfs callback used to retrieve -+ * the value of the CPR3 regulator debug_corner index -+ * @data: Pointer to private data which is equal to the CPR3 -+ * regulator pointer -+ * @val: Output parameter written with the value of -+ * debug_corner -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_debug_corner_index_get(void *data, u64 *val) -+{ -+ struct cpr3_regulator *vreg = data; -+ -+ *val = vreg->debug_corner + CPR3_CORNER_OFFSET; -+ -+ return 0; -+} -+DEFINE_SIMPLE_ATTRIBUTE(cpr3_debug_corner_index_fops, -+ cpr3_debug_corner_index_get, -+ cpr3_debug_corner_index_set, -+ "%llu\n"); -+ -+/** -+ * cpr3_debug_current_corner_index_get() - debugfs callback used to retrieve -+ * the value of the CPR3 regulator current_corner index -+ * @data: Pointer to private data which is equal to the CPR3 -+ * regulator pointer -+ * @val: Output parameter written with the value of -+ * current_corner -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_debug_current_corner_index_get(void *data, u64 *val) -+{ -+ struct cpr3_regulator *vreg = data; -+ -+ *val = vreg->current_corner + CPR3_CORNER_OFFSET; -+ -+ return 0; -+} -+DEFINE_SIMPLE_ATTRIBUTE(cpr3_debug_current_corner_index_fops, -+ cpr3_debug_current_corner_index_get, -+ NULL, "%llu\n"); -+ -+/** -+ * cpr3_regulator_debugfs_vreg_add() - add debugfs files to expose configuration -+ * data for the CPR3 regulator -+ * @vreg: Pointer to the CPR3 regulator -+ * @thread_dir CPR3 thread debugfs directory handle -+ * -+ * Return: none -+ */ -+static void cpr3_regulator_debugfs_vreg_add(struct cpr3_regulator *vreg, -+ struct dentry *thread_dir) -+{ -+ struct dentry *temp, *corner_dir, *vreg_dir; -+ -+ vreg_dir = debugfs_create_dir(vreg->name, thread_dir); -+ if (IS_ERR_OR_NULL(vreg_dir)) { -+ cpr3_err(vreg, "%s debugfs directory creation failed\n", -+ vreg->name); -+ return; -+ } -+ -+ temp = debugfs_create_int("speed_bin_fuse", S_IRUGO, vreg_dir, -+ &vreg->speed_bin_fuse); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(vreg, "speed_bin_fuse debugfs file creation failed\n"); -+ return; -+ } -+ -+ temp = debugfs_create_int("cpr_rev_fuse", S_IRUGO, vreg_dir, -+ &vreg->cpr_rev_fuse); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(vreg, "cpr_rev_fuse debugfs file creation failed\n"); -+ return; -+ } -+ -+ temp = debugfs_create_int("fuse_combo", S_IRUGO, vreg_dir, -+ &vreg->fuse_combo); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(vreg, "fuse_combo debugfs file creation failed\n"); -+ return; -+ } -+ -+ temp = debugfs_create_int("corner_count", S_IRUGO, vreg_dir, -+ &vreg->corner_count); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(vreg, "corner_count debugfs file creation failed\n"); -+ return; -+ } -+ -+ corner_dir = debugfs_create_dir("corner", vreg_dir); -+ if (IS_ERR_OR_NULL(corner_dir)) { -+ cpr3_err(vreg, "corner debugfs directory creation failed\n"); -+ return; -+ } -+ -+ temp = debugfs_create_file("index", S_IRUGO | S_IWUSR, corner_dir, -+ vreg, &cpr3_debug_corner_index_fops); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(vreg, "index debugfs file creation failed\n"); -+ return; -+ } -+ -+ cpr3_regulator_debugfs_corner_add(vreg, corner_dir, -+ &vreg->debug_corner); -+ -+ corner_dir = debugfs_create_dir("current_corner", vreg_dir); -+ if (IS_ERR_OR_NULL(corner_dir)) { -+ cpr3_err(vreg, "current_corner debugfs directory creation failed\n"); -+ return; -+ } -+ -+ temp = debugfs_create_file("index", S_IRUGO, corner_dir, -+ vreg, &cpr3_debug_current_corner_index_fops); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(vreg, "index debugfs file creation failed\n"); -+ return; -+ } -+ -+ cpr3_regulator_debugfs_corner_add(vreg, corner_dir, -+ &vreg->current_corner); -+} -+ -+/** -+ * cpr3_regulator_debugfs_thread_add() - add debugfs files to expose -+ * configuration data for the CPR thread -+ * @thread: Pointer to the CPR3 thread -+ * -+ * Return: none -+ */ -+static void cpr3_regulator_debugfs_thread_add(struct cpr3_thread *thread) -+{ -+ struct cpr3_controller *ctrl = thread->ctrl; -+ struct dentry *aggr_dir, *temp, *thread_dir; -+ struct cpr3_debug_corner_info *info; -+ char buf[20]; -+ int *index; -+ int i; -+ -+ scnprintf(buf, sizeof(buf), "thread%u", thread->thread_id); -+ thread_dir = debugfs_create_dir(buf, thread->ctrl->debugfs); -+ if (IS_ERR_OR_NULL(thread_dir)) { -+ cpr3_err(ctrl, "thread %u %s debugfs directory creation failed\n", -+ thread->thread_id, buf); -+ return; -+ } -+ -+ aggr_dir = debugfs_create_dir("max_aggregated_params", thread_dir); -+ if (IS_ERR_OR_NULL(aggr_dir)) { -+ cpr3_err(ctrl, "thread %u max_aggregated_params debugfs directory creation failed\n", -+ thread->thread_id); -+ return; -+ } -+ -+ temp = debugfs_create_int("floor_volt", S_IRUGO, aggr_dir, -+ &thread->aggr_corner.floor_volt); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(ctrl, "thread %u aggr floor_volt debugfs file creation failed\n", -+ thread->thread_id); -+ return; -+ } -+ -+ temp = debugfs_create_int("ceiling_volt", S_IRUGO, aggr_dir, -+ &thread->aggr_corner.ceiling_volt); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(ctrl, "thread %u aggr ceiling_volt debugfs file creation failed\n", -+ thread->thread_id); -+ return; -+ } -+ -+ temp = debugfs_create_int("open_loop_volt", S_IRUGO, aggr_dir, -+ &thread->aggr_corner.open_loop_volt); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(ctrl, "thread %u aggr open_loop_volt debugfs file creation failed\n", -+ thread->thread_id); -+ return; -+ } -+ -+ temp = debugfs_create_int("last_volt", S_IRUGO, aggr_dir, -+ &thread->aggr_corner.last_volt); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(ctrl, "thread %u aggr last_volt debugfs file creation failed\n", -+ thread->thread_id); -+ return; -+ } -+ -+ info = devm_kzalloc(thread->ctrl->dev, sizeof(*info), GFP_KERNEL); -+ index = devm_kzalloc(thread->ctrl->dev, sizeof(*index), GFP_KERNEL); -+ if (!info || !index) -+ return; -+ *index = 0; -+ info->vreg = &thread->vreg[0]; -+ info->index = index; -+ info->corner = &thread->aggr_corner; -+ -+ temp = debugfs_create_file("target_quots", S_IRUGO, aggr_dir, -+ info, &cpr3_debug_quot_fops); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(ctrl, "thread %u target_quots debugfs file creation failed\n", -+ thread->thread_id); -+ return; -+ } -+ -+ for (i = 0; i < thread->vreg_count; i++) -+ cpr3_regulator_debugfs_vreg_add(&thread->vreg[i], thread_dir); -+} -+ -+/** -+ * cpr3_debug_closed_loop_enable_set() - debugfs callback used to change the -+ * value of the CPR controller cpr_allowed_sw flag which enables or -+ * disables closed-loop operation -+ * @data: Pointer to private data which is equal to the CPR -+ * controller pointer -+ * @val: New value for cpr_allowed_sw -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_debug_closed_loop_enable_set(void *data, u64 val) -+{ -+ struct cpr3_controller *ctrl = data; -+ bool enable = !!val; -+ int rc; -+ -+ mutex_lock(&ctrl->lock); -+ -+ if (ctrl->cpr_allowed_sw == enable) -+ goto done; -+ -+ if (enable && !ctrl->cpr_allowed_hw) { -+ cpr3_err(ctrl, "CPR closed-loop operation is not allowed\n"); -+ goto done; -+ } -+ -+ ctrl->cpr_allowed_sw = enable; -+ -+ rc = cpr3_regulator_update_ctrl_state(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "could not change CPR enable state=%u, rc=%d\n", -+ enable, rc); -+ goto done; -+ } -+ -+ if (ctrl->proc_clock_throttle && !ctrl->cpr_enabled) { -+ rc = cpr3_clock_enable(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "clock enable failed, rc=%d\n", -+ rc); -+ goto done; -+ } -+ ctrl->cpr_enabled = true; -+ -+ cpr3_write(ctrl, CPR3_REG_PD_THROTTLE, -+ CPR3_PD_THROTTLE_DISABLE); -+ -+ cpr3_clock_disable(ctrl); -+ ctrl->cpr_enabled = false; -+ } -+ -+ cpr3_debug(ctrl, "closed-loop=%s\n", enable ? "enabled" : "disabled"); -+done: -+ mutex_unlock(&ctrl->lock); -+ return 0; -+} -+ -+/** -+ * cpr3_debug_closed_loop_enable_get() - debugfs callback used to retrieve -+ * the value of the CPR controller cpr_allowed_sw flag which -+ * indicates if closed-loop operation is enabled -+ * @data: Pointer to private data which is equal to the CPR -+ * controller pointer -+ * @val: Output parameter written with the value of -+ * cpr_allowed_sw -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_debug_closed_loop_enable_get(void *data, u64 *val) -+{ -+ struct cpr3_controller *ctrl = data; -+ -+ *val = ctrl->cpr_allowed_sw; -+ -+ return 0; -+} -+DEFINE_SIMPLE_ATTRIBUTE(cpr3_debug_closed_loop_enable_fops, -+ cpr3_debug_closed_loop_enable_get, -+ cpr3_debug_closed_loop_enable_set, -+ "%llu\n"); -+ -+/** -+ * cpr3_debug_hw_closed_loop_enable_set() - debugfs callback used to change the -+ * value of the CPR controller use_hw_closed_loop flag which -+ * switches between software closed-loop and hardware closed-loop -+ * operation for CPR3 and CPR4 controllers and between open-loop -+ * and full hardware closed-loop operation for CPRh controllers. -+ * @data: Pointer to private data which is equal to the CPR -+ * controller pointer -+ * @val: New value for use_hw_closed_loop -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_debug_hw_closed_loop_enable_set(void *data, u64 val) -+{ -+ struct cpr3_controller *ctrl = data; -+ bool use_hw_closed_loop = !!val; -+ struct cpr3_regulator *vreg; -+ bool cpr_enabled; -+ int i, j, k, rc; -+ -+ mutex_lock(&ctrl->lock); -+ -+ if (ctrl->use_hw_closed_loop == use_hw_closed_loop) -+ goto done; -+ -+ if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR4) { -+ rc = cpr3_ctrl_clear_cpr4_config(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "failed to clear CPR4 configuration,rc=%d\n", -+ rc); -+ goto done; -+ } -+ } -+ -+ cpr3_ctrl_loop_disable(ctrl); -+ -+ ctrl->use_hw_closed_loop = use_hw_closed_loop; -+ -+ cpr_enabled = ctrl->cpr_enabled; -+ -+ /* Ensure that CPR clocks are enabled before writing to registers. */ -+ if (!cpr_enabled) { -+ rc = cpr3_clock_enable(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "clock enable failed, rc=%d\n", rc); -+ goto done; -+ } -+ ctrl->cpr_enabled = true; -+ } -+ -+ if (ctrl->use_hw_closed_loop) -+ cpr3_write(ctrl, CPR3_REG_IRQ_EN, 0); -+ -+ if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR4) { -+ cpr3_masked_write(ctrl, CPR4_REG_MARGIN_ADJ_CTL, -+ CPR4_MARGIN_ADJ_CTL_HW_CLOSED_LOOP_EN_MASK, -+ ctrl->use_hw_closed_loop -+ ? CPR4_MARGIN_ADJ_CTL_HW_CLOSED_LOOP_ENABLE -+ : CPR4_MARGIN_ADJ_CTL_HW_CLOSED_LOOP_DISABLE); -+ } else if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR3) { -+ cpr3_write(ctrl, CPR3_REG_HW_CLOSED_LOOP, -+ ctrl->use_hw_closed_loop -+ ? CPR3_HW_CLOSED_LOOP_ENABLE -+ : CPR3_HW_CLOSED_LOOP_DISABLE); -+ } -+ -+ /* Turn off CPR clocks if they were off before this function call. */ -+ if (!cpr_enabled) { -+ cpr3_clock_disable(ctrl); -+ ctrl->cpr_enabled = false; -+ } -+ -+ if (ctrl->use_hw_closed_loop && ctrl->ctrl_type == CPR_CTRL_TYPE_CPR3) { -+ rc = regulator_enable(ctrl->vdd_limit_regulator); -+ if (rc) { -+ cpr3_err(ctrl, "CPR limit regulator enable failed, rc=%d\n", -+ rc); -+ goto done; -+ } -+ } else if (!ctrl->use_hw_closed_loop -+ && ctrl->ctrl_type == CPR_CTRL_TYPE_CPR3) { -+ rc = regulator_disable(ctrl->vdd_limit_regulator); -+ if (rc) { -+ cpr3_err(ctrl, "CPR limit regulator disable failed, rc=%d\n", -+ rc); -+ goto done; -+ } -+ } -+ -+ /* -+ * Due to APM and mem-acc floor restriction constraints, -+ * the closed-loop voltage may be different when using -+ * software closed-loop vs hardware closed-loop. Therefore, -+ * reset the cached closed-loop voltage for all corners to the -+ * corresponding open-loop voltage when switching between -+ * SW and HW closed-loop mode. -+ */ -+ for (i = 0; i < ctrl->thread_count; i++) { -+ for (j = 0; j < ctrl->thread[i].vreg_count; j++) { -+ vreg = &ctrl->thread[i].vreg[j]; -+ for (k = 0; k < vreg->corner_count; k++) -+ vreg->corner[k].last_volt -+ = vreg->corner[k].open_loop_volt; -+ } -+ } -+ -+ /* Skip last_volt caching */ -+ ctrl->last_corner_was_closed_loop = false; -+ -+ rc = cpr3_regulator_update_ctrl_state(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "could not change CPR HW closed-loop enable state=%u, rc=%d\n", -+ use_hw_closed_loop, rc); -+ goto done; -+ } -+ -+ cpr3_debug(ctrl, "CPR mode=%s\n", -+ use_hw_closed_loop ? -+ "HW closed-loop" : "SW closed-loop"); -+done: -+ mutex_unlock(&ctrl->lock); -+ return 0; -+} -+ -+/** -+ * cpr3_debug_hw_closed_loop_enable_get() - debugfs callback used to retrieve -+ * the value of the CPR controller use_hw_closed_loop flag which -+ * indicates if hardware closed-loop operation is being used in -+ * place of software closed-loop operation -+ * @data: Pointer to private data which is equal to the CPR -+ * controller pointer -+ * @val: Output parameter written with the value of -+ * use_hw_closed_loop -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_debug_hw_closed_loop_enable_get(void *data, u64 *val) -+{ -+ struct cpr3_controller *ctrl = data; -+ -+ *val = ctrl->use_hw_closed_loop; -+ -+ return 0; -+} -+DEFINE_SIMPLE_ATTRIBUTE(cpr3_debug_hw_closed_loop_enable_fops, -+ cpr3_debug_hw_closed_loop_enable_get, -+ cpr3_debug_hw_closed_loop_enable_set, -+ "%llu\n"); -+ -+/** -+ * cpr3_debug_trigger_aging_measurement_set() - debugfs callback used to trigger -+ * another CPR measurement -+ * @data: Pointer to private data which is equal to the CPR -+ * controller pointer -+ * @val: Unused -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_debug_trigger_aging_measurement_set(void *data, u64 val) -+{ -+ struct cpr3_controller *ctrl = data; -+ int rc; -+ -+ mutex_lock(&ctrl->lock); -+ -+ if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR4) { -+ rc = cpr3_ctrl_clear_cpr4_config(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "failed to clear CPR4 configuration,rc=%d\n", -+ rc); -+ goto done; -+ } -+ } -+ -+ cpr3_ctrl_loop_disable(ctrl); -+ -+ cpr3_regulator_set_aging_ref_adjustment(ctrl, INT_MAX); -+ ctrl->aging_required = true; -+ ctrl->aging_succeeded = false; -+ ctrl->aging_failed = false; -+ -+ rc = cpr3_regulator_update_ctrl_state(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "could not update the CPR controller state, rc=%d\n", -+ rc); -+ goto done; -+ } -+ -+done: -+ mutex_unlock(&ctrl->lock); -+ return 0; -+} -+DEFINE_SIMPLE_ATTRIBUTE(cpr3_debug_trigger_aging_measurement_fops, -+ NULL, -+ cpr3_debug_trigger_aging_measurement_set, -+ "%llu\n"); -+ -+/** -+ * cpr3_regulator_debugfs_ctrl_add() - add debugfs files to expose configuration -+ * data for the CPR controller -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: none -+ */ -+static void cpr3_regulator_debugfs_ctrl_add(struct cpr3_controller *ctrl) -+{ -+ struct dentry *temp, *aggr_dir; -+ int i; -+ -+ /* Add cpr3-regulator base directory if it isn't present already. */ -+ if (cpr3_debugfs_base == NULL) { -+ cpr3_debugfs_base = debugfs_create_dir("cpr3-regulator", NULL); -+ if (IS_ERR_OR_NULL(cpr3_debugfs_base)) { -+ cpr3_err(ctrl, "cpr3-regulator debugfs base directory creation failed\n"); -+ cpr3_debugfs_base = NULL; -+ return; -+ } -+ } -+ -+ ctrl->debugfs = debugfs_create_dir(ctrl->name, cpr3_debugfs_base); -+ if (IS_ERR_OR_NULL(ctrl->debugfs)) { -+ cpr3_err(ctrl, "cpr3-regulator controller debugfs directory creation failed\n"); -+ return; -+ } -+ -+ temp = debugfs_create_file("cpr_closed_loop_enable", S_IRUGO | S_IWUSR, -+ ctrl->debugfs, ctrl, -+ &cpr3_debug_closed_loop_enable_fops); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(ctrl, "cpr_closed_loop_enable debugfs file creation failed\n"); -+ return; -+ } -+ -+ if (ctrl->supports_hw_closed_loop) { -+ temp = debugfs_create_file("use_hw_closed_loop", -+ S_IRUGO | S_IWUSR, ctrl->debugfs, ctrl, -+ &cpr3_debug_hw_closed_loop_enable_fops); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(ctrl, "use_hw_closed_loop debugfs file creation failed\n"); -+ return; -+ } -+ } -+ -+ temp = debugfs_create_int("thread_count", S_IRUGO, ctrl->debugfs, -+ &ctrl->thread_count); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(ctrl, "thread_count debugfs file creation failed\n"); -+ return; -+ } -+ -+ if (ctrl->apm) { -+ temp = debugfs_create_int("apm_threshold_volt", S_IRUGO, -+ ctrl->debugfs, &ctrl->apm_threshold_volt); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(ctrl, "apm_threshold_volt debugfs file creation failed\n"); -+ return; -+ } -+ } -+ -+ if (ctrl->aging_required || ctrl->aging_succeeded -+ || ctrl->aging_failed) { -+ temp = debugfs_create_int("aging_adj_volt", S_IRUGO, -+ ctrl->debugfs, &ctrl->aging_ref_adjust_volt); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(ctrl, "aging_adj_volt debugfs file creation failed\n"); -+ return; -+ } -+ -+ temp = debugfs_create_file("aging_succeeded", S_IRUGO, -+ ctrl->debugfs, &ctrl->aging_succeeded, &fops_bool_ro); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(ctrl, "aging_succeeded debugfs file creation failed\n"); -+ return; -+ } -+ -+ temp = debugfs_create_file("aging_failed", S_IRUGO, -+ ctrl->debugfs, &ctrl->aging_failed, &fops_bool_ro); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(ctrl, "aging_failed debugfs file creation failed\n"); -+ return; -+ } -+ -+ temp = debugfs_create_file("aging_trigger", S_IWUSR, -+ ctrl->debugfs, ctrl, -+ &cpr3_debug_trigger_aging_measurement_fops); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(ctrl, "aging_trigger debugfs file creation failed\n"); -+ return; -+ } -+ } -+ -+ aggr_dir = debugfs_create_dir("max_aggregated_voltages", ctrl->debugfs); -+ if (IS_ERR_OR_NULL(aggr_dir)) { -+ cpr3_err(ctrl, "max_aggregated_voltages debugfs directory creation failed\n"); -+ return; -+ } -+ -+ temp = debugfs_create_int("floor_volt", S_IRUGO, aggr_dir, -+ &ctrl->aggr_corner.floor_volt); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(ctrl, "aggr floor_volt debugfs file creation failed\n"); -+ return; -+ } -+ -+ temp = debugfs_create_int("ceiling_volt", S_IRUGO, aggr_dir, -+ &ctrl->aggr_corner.ceiling_volt); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(ctrl, "aggr ceiling_volt debugfs file creation failed\n"); -+ return; -+ } -+ -+ temp = debugfs_create_int("open_loop_volt", S_IRUGO, aggr_dir, -+ &ctrl->aggr_corner.open_loop_volt); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(ctrl, "aggr open_loop_volt debugfs file creation failed\n"); -+ return; -+ } -+ -+ temp = debugfs_create_int("last_volt", S_IRUGO, aggr_dir, -+ &ctrl->aggr_corner.last_volt); -+ if (IS_ERR_OR_NULL(temp)) { -+ cpr3_err(ctrl, "aggr last_volt debugfs file creation failed\n"); -+ return; -+ } -+ -+ for (i = 0; i < ctrl->thread_count; i++) -+ cpr3_regulator_debugfs_thread_add(&ctrl->thread[i]); -+} -+ -+/** -+ * cpr3_regulator_debugfs_ctrl_remove() - remove debugfs files for the CPR -+ * controller -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Note, this function must be called after the controller has been removed from -+ * cpr3_controller_list and while the cpr3_controller_list_mutex lock is held. -+ * -+ * Return: none -+ */ -+static void cpr3_regulator_debugfs_ctrl_remove(struct cpr3_controller *ctrl) -+{ -+ if (list_empty(&cpr3_controller_list)) { -+ debugfs_remove_recursive(cpr3_debugfs_base); -+ cpr3_debugfs_base = NULL; -+ } else { -+ debugfs_remove_recursive(ctrl->debugfs); -+ } -+} -+ -+/** -+ * cpr3_regulator_init_ctrl_data() - performs initialization of CPR controller -+ * elements -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_regulator_init_ctrl_data(struct cpr3_controller *ctrl) -+{ -+ /* Read the initial vdd voltage from hardware. */ -+ ctrl->aggr_corner.last_volt -+ = regulator_get_voltage(ctrl->vdd_regulator); -+ if (ctrl->aggr_corner.last_volt < 0) { -+ cpr3_err(ctrl, "regulator_get_voltage(vdd) failed, rc=%d\n", -+ ctrl->aggr_corner.last_volt); -+ return ctrl->aggr_corner.last_volt; -+ } -+ ctrl->aggr_corner.open_loop_volt = ctrl->aggr_corner.last_volt; -+ -+ return 0; -+} -+ -+/** -+ * cpr3_regulator_init_vreg_data() - performs initialization of common CPR3 -+ * regulator elements and validate aging configurations -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_regulator_init_vreg_data(struct cpr3_regulator *vreg) -+{ -+ int i, j; -+ bool init_aging; -+ -+ vreg->current_corner = CPR3_REGULATOR_CORNER_INVALID; -+ vreg->last_closed_loop_corner = CPR3_REGULATOR_CORNER_INVALID; -+ -+ init_aging = vreg->aging_allowed && vreg->thread->ctrl->aging_required; -+ -+ for (i = 0; i < vreg->corner_count; i++) { -+ vreg->corner[i].last_volt = vreg->corner[i].open_loop_volt; -+ vreg->corner[i].irq_en = CPR3_IRQ_UP | CPR3_IRQ_DOWN; -+ -+ vreg->corner[i].ro_mask = 0; -+ for (j = 0; j < CPR3_RO_COUNT; j++) { -+ if (vreg->corner[i].target_quot[j] == 0) -+ vreg->corner[i].ro_mask |= BIT(j); -+ } -+ -+ if (init_aging) { -+ vreg->corner[i].unaged_floor_volt -+ = vreg->corner[i].floor_volt; -+ vreg->corner[i].unaged_ceiling_volt -+ = vreg->corner[i].ceiling_volt; -+ vreg->corner[i].unaged_open_loop_volt -+ = vreg->corner[i].open_loop_volt; -+ } -+ -+ if (vreg->aging_allowed) { -+ if (vreg->corner[i].unaged_floor_volt <= 0) { -+ cpr3_err(vreg, "invalid unaged_floor_volt[%d] = %d\n", -+ i, vreg->corner[i].unaged_floor_volt); -+ return -EINVAL; -+ } -+ if (vreg->corner[i].unaged_ceiling_volt <= 0) { -+ cpr3_err(vreg, "invalid unaged_ceiling_volt[%d] = %d\n", -+ i, vreg->corner[i].unaged_ceiling_volt); -+ return -EINVAL; -+ } -+ if (vreg->corner[i].unaged_open_loop_volt <= 0) { -+ cpr3_err(vreg, "invalid unaged_open_loop_volt[%d] = %d\n", -+ i, vreg->corner[i].unaged_open_loop_volt); -+ return -EINVAL; -+ } -+ } -+ } -+ -+ if (vreg->aging_allowed && vreg->corner[vreg->aging_corner].ceiling_volt -+ > vreg->thread->ctrl->aging_ref_volt) { -+ cpr3_err(vreg, "aging corner %d ceiling voltage = %d > aging ref voltage = %d uV\n", -+ vreg->aging_corner, -+ vreg->corner[vreg->aging_corner].ceiling_volt, -+ vreg->thread->ctrl->aging_ref_volt); -+ return -EINVAL; -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr3_regulator_suspend() - perform common required CPR3 power down steps -+ * before the system enters suspend -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_regulator_suspend(struct cpr3_controller *ctrl) -+{ -+ int rc; -+ -+ mutex_lock(&ctrl->lock); -+ -+ if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR4) { -+ rc = cpr3_ctrl_clear_cpr4_config(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "failed to clear CPR4 configuration,rc=%d\n", -+ rc); -+ mutex_unlock(&ctrl->lock); -+ return rc; -+ } -+ } -+ -+ cpr3_ctrl_loop_disable(ctrl); -+ -+ rc = cpr3_closed_loop_disable(ctrl); -+ if (rc) -+ cpr3_err(ctrl, "could not disable CPR, rc=%d\n", rc); -+ -+ ctrl->cpr_suspended = true; -+ -+ mutex_unlock(&ctrl->lock); -+ return 0; -+} -+ -+/** -+ * cpr3_regulator_resume() - perform common required CPR3 power up steps after -+ * the system resumes from suspend -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_regulator_resume(struct cpr3_controller *ctrl) -+{ -+ int rc; -+ -+ mutex_lock(&ctrl->lock); -+ -+ ctrl->cpr_suspended = false; -+ rc = cpr3_regulator_update_ctrl_state(ctrl); -+ if (rc) -+ cpr3_err(ctrl, "could not enable CPR, rc=%d\n", rc); -+ -+ mutex_unlock(&ctrl->lock); -+ return 0; -+} -+ -+/** -+ * cpr3_regulator_validate_controller() - verify the data passed in via the -+ * cpr3_controller data structure -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_regulator_validate_controller(struct cpr3_controller *ctrl) -+{ -+ struct cpr3_thread *thread; -+ struct cpr3_regulator *vreg; -+ int i, j, allow_boost_vreg_count = 0; -+ -+ if (!ctrl->vdd_regulator) { -+ cpr3_err(ctrl, "vdd regulator missing\n"); -+ return -EINVAL; -+ } else if (ctrl->sensor_count <= 0 -+ || ctrl->sensor_count > CPR3_MAX_SENSOR_COUNT) { -+ cpr3_err(ctrl, "invalid CPR sensor count=%d\n", -+ ctrl->sensor_count); -+ return -EINVAL; -+ } else if (!ctrl->sensor_owner) { -+ cpr3_err(ctrl, "CPR sensor ownership table missing\n"); -+ return -EINVAL; -+ } -+ -+ if (ctrl->aging_required) { -+ for (i = 0; i < ctrl->aging_sensor_count; i++) { -+ if (ctrl->aging_sensor[i].sensor_id -+ >= ctrl->sensor_count) { -+ cpr3_err(ctrl, "aging_sensor[%d] id=%u is not in the value range 0-%d", -+ i, ctrl->aging_sensor[i].sensor_id, -+ ctrl->sensor_count - 1); -+ return -EINVAL; -+ } -+ } -+ } -+ -+ for (i = 0; i < ctrl->thread_count; i++) { -+ thread = &ctrl->thread[i]; -+ for (j = 0; j < thread->vreg_count; j++) { -+ vreg = &thread->vreg[j]; -+ if (vreg->allow_boost) -+ allow_boost_vreg_count++; -+ } -+ } -+ -+ if (allow_boost_vreg_count > 1) { -+ /* -+ * Boost feature is not allowed to be used for more -+ * than one CPR3 regulator of a CPR3 controller. -+ */ -+ cpr3_err(ctrl, "Boost feature is enabled for more than one regulator\n"); -+ return -EINVAL; -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr3_panic_callback() - panic notification callback function. This function -+ * is invoked when a kernel panic occurs. -+ * @nfb: Notifier block pointer of CPR3 controller -+ * @event: Value passed unmodified to notifier function -+ * @data: Pointer passed unmodified to notifier function -+ * -+ * Return: NOTIFY_OK -+ */ -+static int cpr3_panic_callback(struct notifier_block *nfb, -+ unsigned long event, void *data) -+{ -+ struct cpr3_controller *ctrl = container_of(nfb, -+ struct cpr3_controller, panic_notifier); -+ struct cpr3_panic_regs_info *regs_info = ctrl->panic_regs_info; -+ struct cpr3_reg_info *reg; -+ int i = 0; -+ -+ for (i = 0; i < regs_info->reg_count; i++) { -+ reg = &(regs_info->regs[i]); -+ reg->value = readl_relaxed(reg->virt_addr); -+ pr_err("%s[0x%08x] = 0x%08x\n", reg->name, reg->addr, -+ reg->value); -+ } -+ /* -+ * Barrier to ensure that the information has been updated in the -+ * structure. -+ */ -+ mb(); -+ -+ return NOTIFY_OK; -+} -+ -+/** -+ * cpr3_regulator_register() - register the regulators for a CPR3 controller and -+ * perform CPR hardware initialization -+ * @pdev: Platform device pointer for the CPR3 controller -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_regulator_register(struct platform_device *pdev, -+ struct cpr3_controller *ctrl) -+{ -+ struct device *dev = &pdev->dev; -+ struct resource *res; -+ int i, j, rc; -+ -+ if (!dev->of_node) { -+ dev_err(dev, "%s: Device tree node is missing\n", __func__); -+ return -EINVAL; -+ } -+ -+ if (!ctrl || !ctrl->name) { -+ dev_err(dev, "%s: CPR controller data is missing\n", __func__); -+ return -EINVAL; -+ } -+ -+ rc = cpr3_regulator_validate_controller(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "controller validation failed, rc=%d\n", rc); -+ return rc; -+ } -+ -+ mutex_init(&ctrl->lock); -+ -+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "cpr_ctrl"); -+ if (!res || !res->start) { -+ cpr3_err(ctrl, "CPR controller address is missing\n"); -+ return -ENXIO; -+ } -+ ctrl->cpr_ctrl_base = devm_ioremap(dev, res->start, resource_size(res)); -+ -+ if (ctrl->aging_possible_mask) { -+ /* -+ * Aging possible register address is required if an aging -+ * possible mask has been specified. -+ */ -+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, -+ "aging_allowed"); -+ if (!res || !res->start) { -+ cpr3_err(ctrl, "CPR aging allowed address is missing\n"); -+ return -ENXIO; -+ } -+ ctrl->aging_possible_reg = devm_ioremap(dev, res->start, -+ resource_size(res)); -+ } -+ -+ ctrl->irq = platform_get_irq_byname(pdev, "cpr"); -+ if (ctrl->irq < 0) { -+ cpr3_err(ctrl, "missing CPR interrupt\n"); -+ return ctrl->irq; -+ } -+ -+ if (ctrl->supports_hw_closed_loop) { -+ if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR3) { -+ ctrl->ceiling_irq = platform_get_irq_byname(pdev, -+ "ceiling"); -+ if (ctrl->ceiling_irq < 0) { -+ cpr3_err(ctrl, "missing ceiling interrupt\n"); -+ return ctrl->ceiling_irq; -+ } -+ } -+ } -+ -+ rc = cpr3_regulator_init_ctrl_data(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "CPR controller data initialization failed, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ for (i = 0; i < ctrl->thread_count; i++) { -+ for (j = 0; j < ctrl->thread[i].vreg_count; j++) { -+ rc = cpr3_regulator_init_vreg_data( -+ &ctrl->thread[i].vreg[j]); -+ if (rc) -+ return rc; -+ cpr3_print_quots(&ctrl->thread[i].vreg[j]); -+ } -+ } -+ -+ /* -+ * Add the maximum possible aging voltage margin until it is possible -+ * to perform an aging measurement. -+ */ -+ if (ctrl->aging_required) -+ cpr3_regulator_set_aging_ref_adjustment(ctrl, INT_MAX); -+ -+ rc = cpr3_regulator_init_ctrl(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "CPR controller initialization failed, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ /* Register regulator devices for all threads. */ -+ for (i = 0; i < ctrl->thread_count; i++) { -+ for (j = 0; j < ctrl->thread[i].vreg_count; j++) { -+ rc = cpr3_regulator_vreg_register( -+ &ctrl->thread[i].vreg[j]); -+ if (rc) { -+ cpr3_err(&ctrl->thread[i].vreg[j], "failed to register regulator, rc=%d\n", -+ rc); -+ goto free_regulators; -+ } -+ } -+ } -+ -+ rc = devm_request_threaded_irq(dev, ctrl->irq, NULL, -+ cpr3_irq_handler, -+ IRQF_ONESHOT | -+ IRQF_TRIGGER_RISING, -+ "cpr3", ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "could not request IRQ %d, rc=%d\n", -+ ctrl->irq, rc); -+ goto free_regulators; -+ } -+ -+ if (ctrl->supports_hw_closed_loop && -+ ctrl->ctrl_type == CPR_CTRL_TYPE_CPR3) { -+ rc = devm_request_threaded_irq(dev, ctrl->ceiling_irq, NULL, -+ cpr3_ceiling_irq_handler, -+ IRQF_ONESHOT | IRQF_TRIGGER_RISING, -+ "cpr3_ceiling", ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "could not request ceiling IRQ %d, rc=%d\n", -+ ctrl->ceiling_irq, rc); -+ goto free_regulators; -+ } -+ } -+ -+ mutex_lock(&cpr3_controller_list_mutex); -+ cpr3_regulator_debugfs_ctrl_add(ctrl); -+ list_add(&ctrl->list, &cpr3_controller_list); -+ mutex_unlock(&cpr3_controller_list_mutex); -+ -+ if (ctrl->panic_regs_info) { -+ /* Register panic notification call back */ -+ ctrl->panic_notifier.notifier_call = cpr3_panic_callback; -+ atomic_notifier_chain_register(&panic_notifier_list, -+ &ctrl->panic_notifier); -+ } -+ -+ return 0; -+ -+free_regulators: -+ for (i = 0; i < ctrl->thread_count; i++) -+ for (j = 0; j < ctrl->thread[i].vreg_count; j++) -+ if (!IS_ERR_OR_NULL(ctrl->thread[i].vreg[j].rdev)) -+ regulator_unregister( -+ ctrl->thread[i].vreg[j].rdev); -+ return rc; -+} -+ -+/** -+ * cpr3_open_loop_regulator_register() - register the regulators for a CPR3 -+ * controller which will always work in Open loop and -+ * won't support close loop. -+ * @pdev: Platform device pointer for the CPR3 controller -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_open_loop_regulator_register(struct platform_device *pdev, -+ struct cpr3_controller *ctrl) -+{ -+ struct device *dev = &pdev->dev; -+ struct cpr3_regulator *vreg; -+ int i, j, rc; -+ -+ if (!dev->of_node) { -+ dev_err(dev, "%s: Device tree node is missing\n", __func__); -+ return -EINVAL; -+ } -+ -+ if (!ctrl || !ctrl->name) { -+ dev_err(dev, "%s: CPR controller data is missing\n", __func__); -+ return -EINVAL; -+ } -+ -+ if (!ctrl->vdd_regulator) { -+ cpr3_err(ctrl, "vdd regulator missing\n"); -+ return -EINVAL; -+ } -+ -+ mutex_init(&ctrl->lock); -+ -+ rc = cpr3_regulator_init_ctrl_data(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "CPR controller data initialization failed, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ for (i = 0; i < ctrl->thread_count; i++) { -+ for (j = 0; j < ctrl->thread[i].vreg_count; j++) { -+ vreg = &ctrl->thread[i].vreg[j]; -+ vreg->corner[i].last_volt = -+ vreg->corner[i].open_loop_volt; -+ } -+ } -+ -+ /* Register regulator devices for all threads. */ -+ for (i = 0; i < ctrl->thread_count; i++) { -+ for (j = 0; j < ctrl->thread[i].vreg_count; j++) { -+ rc = cpr3_regulator_vreg_register( -+ &ctrl->thread[i].vreg[j]); -+ if (rc) { -+ cpr3_err(&ctrl->thread[i].vreg[j], "failed to register regulator, rc=%d\n", -+ rc); -+ goto free_regulators; -+ } -+ } -+ } -+ -+ mutex_lock(&cpr3_controller_list_mutex); -+ list_add(&ctrl->list, &cpr3_controller_list); -+ mutex_unlock(&cpr3_controller_list_mutex); -+ -+ return 0; -+ -+free_regulators: -+ for (i = 0; i < ctrl->thread_count; i++) -+ for (j = 0; j < ctrl->thread[i].vreg_count; j++) -+ if (!IS_ERR_OR_NULL(ctrl->thread[i].vreg[j].rdev)) -+ regulator_unregister( -+ ctrl->thread[i].vreg[j].rdev); -+ return rc; -+} -+ -+/** -+ * cpr3_regulator_unregister() - unregister the regulators for a CPR3 controller -+ * and perform CPR hardware shutdown -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_regulator_unregister(struct cpr3_controller *ctrl) -+{ -+ int i, j, rc = 0; -+ -+ mutex_lock(&cpr3_controller_list_mutex); -+ list_del(&ctrl->list); -+ cpr3_regulator_debugfs_ctrl_remove(ctrl); -+ mutex_unlock(&cpr3_controller_list_mutex); -+ -+ if (ctrl->ctrl_type == CPR_CTRL_TYPE_CPR4) { -+ rc = cpr3_ctrl_clear_cpr4_config(ctrl); -+ if (rc) -+ cpr3_err(ctrl, "failed to clear CPR4 configuration,rc=%d\n", -+ rc); -+ } -+ -+ cpr3_ctrl_loop_disable(ctrl); -+ -+ cpr3_closed_loop_disable(ctrl); -+ -+ if (ctrl->vdd_limit_regulator) { -+ regulator_disable(ctrl->vdd_limit_regulator); -+ } -+ -+ for (i = 0; i < ctrl->thread_count; i++) -+ for (j = 0; j < ctrl->thread[i].vreg_count; j++) -+ regulator_unregister(ctrl->thread[i].vreg[j].rdev); -+ -+ if (ctrl->panic_notifier.notifier_call) -+ atomic_notifier_chain_unregister(&panic_notifier_list, -+ &ctrl->panic_notifier); -+ -+ return 0; -+} -+ -+/** -+ * cpr3_open_loop_regulator_unregister() - unregister the regulators for a CPR3 -+ * open loop controller and perform CPR hardware shutdown -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_open_loop_regulator_unregister(struct cpr3_controller *ctrl) -+{ -+ int i, j; -+ -+ mutex_lock(&cpr3_controller_list_mutex); -+ list_del(&ctrl->list); -+ mutex_unlock(&cpr3_controller_list_mutex); -+ -+ if (ctrl->vdd_limit_regulator) { -+ regulator_disable(ctrl->vdd_limit_regulator); -+ } -+ -+ for (i = 0; i < ctrl->thread_count; i++) -+ for (j = 0; j < ctrl->thread[i].vreg_count; j++) -+ regulator_unregister(ctrl->thread[i].vreg[j].rdev); -+ -+ if (ctrl->panic_notifier.notifier_call) -+ atomic_notifier_chain_unregister(&panic_notifier_list, -+ &ctrl->panic_notifier); -+ -+ return 0; -+} ---- /dev/null -+++ b/drivers/regulator/cpr3-regulator.h -@@ -0,0 +1,1211 @@ -+/* -+ * Copyright (c) 2015-2017, The Linux Foundation. All rights reserved. -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 and -+ * only version 2 as published by the Free Software Foundation. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ */ -+ -+#ifndef __REGULATOR_CPR3_REGULATOR_H__ -+#define __REGULATOR_CPR3_REGULATOR_H__ -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+struct cpr3_controller; -+struct cpr3_thread; -+ -+/** -+ * struct cpr3_fuse_param - defines one contiguous segment of a fuse parameter -+ * that is contained within a given row. -+ * @row: Fuse row number -+ * @bit_start: The first bit within the row of the fuse parameter segment -+ * @bit_end: The last bit within the row of the fuse parameter segment -+ * -+ * Each fuse row is 64 bits in length. bit_start and bit_end may take values -+ * from 0 to 63. bit_start must be less than or equal to bit_end. -+ */ -+struct cpr3_fuse_param { -+ unsigned row; -+ unsigned bit_start; -+ unsigned bit_end; -+}; -+ -+/* Each CPR3 sensor has 16 ring oscillators */ -+#define CPR3_RO_COUNT 16 -+ -+/* The maximum number of sensors that can be present on a single CPR loop. */ -+#define CPR3_MAX_SENSOR_COUNT 256 -+ -+/* This constant is used when allocating array printing buffers. */ -+#define MAX_CHARS_PER_INT 10 -+ -+/** -+ * struct cpr4_sdelta - CPR4 controller specific data structure for the sdelta -+ * adjustment table which is used to adjust the VDD supply -+ * voltage automatically based upon the temperature and/or -+ * the number of online CPU cores. -+ * @allow_core_count_adj: Core count adjustments are allowed. -+ * @allow_temp_adj: Temperature based adjustments are allowed. -+ * @max_core_count: Maximum number of cores considered for core count -+ * adjustment logic. -+ * @temp_band_count: Number of temperature bands considered for temperature -+ * based adjustment logic. -+ * @cap_volt: CAP in uV to apply to SDELTA margins with multiple -+ * cpr3-regulators defined for single controller. -+ * @table: SDELTA table with per-online-core and temperature based -+ * adjustments of size (max_core_count * temp_band_count) -+ * Outer: core count -+ * Inner: temperature band -+ * Each element has units of VDD supply steps. Positive -+ * values correspond to a reduction in voltage and negative -+ * value correspond to an increase (this follows the SDELTA -+ * register semantics). -+ * @allow_boost: Voltage boost allowed. -+ * @boost_num_cores: The number of online cores at which the boost voltage -+ * adjustments will be applied -+ * @boost_table: SDELTA table with boost voltage adjustments of size -+ * temp_band_count. Each element has units of VDD supply -+ * steps. Positive values correspond to a reduction in -+ * voltage and negative value correspond to an increase -+ * (this follows the SDELTA register semantics). -+ */ -+struct cpr4_sdelta { -+ bool allow_core_count_adj; -+ bool allow_temp_adj; -+ int max_core_count; -+ int temp_band_count; -+ int cap_volt; -+ int *table; -+ bool allow_boost; -+ int boost_num_cores; -+ int *boost_table; -+}; -+ -+/** -+ * struct cpr3_corner - CPR3 virtual voltage corner data structure -+ * @floor_volt: CPR closed-loop floor voltage in microvolts -+ * @ceiling_volt: CPR closed-loop ceiling voltage in microvolts -+ * @open_loop_volt: CPR open-loop voltage (i.e. initial voltage) in -+ * microvolts -+ * @last_volt: Last known settled CPR closed-loop voltage which is used -+ * when switching to a new corner -+ * @abs_ceiling_volt: The absolute CPR closed-loop ceiling voltage in -+ * microvolts. This is used to limit the ceiling_volt -+ * value when it is increased as a result of aging -+ * adjustment. -+ * @unaged_floor_volt: The CPR closed-loop floor voltage in microvolts before -+ * any aging adjustment is performed -+ * @unaged_ceiling_volt: The CPR closed-loop ceiling voltage in microvolts -+ * before any aging adjustment is performed -+ * @unaged_open_loop_volt: The CPR open-loop voltage (i.e. initial voltage) in -+ * microvolts before any aging adjusment is performed -+ * @system_volt: The system-supply voltage in microvolts or corners or -+ * levels -+ * @mem_acc_volt: The mem-acc-supply voltage in corners -+ * @proc_freq: Processor frequency in Hertz. For CPR rev. 3 and 4 -+ * conrollers, this field is only used by platform specific -+ * CPR3 driver for interpolation. For CPRh-compliant -+ * controllers, this frequency is also utilized by the -+ * clock driver to determine the corner to CPU clock -+ * frequency mappings. -+ * @cpr_fuse_corner: Fused corner index associated with this virtual corner -+ * (only used by platform specific CPR3 driver for -+ * mapping purposes) -+ * @target_quot: Array of target quotient values to use for each ring -+ * oscillator (RO) for this corner. A value of 0 should be -+ * specified as the target quotient for each RO that is -+ * unused by this corner. -+ * @ro_scale: Array of CPR ring oscillator (RO) scaling factors. The -+ * scaling factor for each RO is defined from RO0 to RO15 -+ * with units of QUOT/V. A value of 0 may be specified for -+ * an RO that is unused. -+ * @ro_mask: Bitmap where each of the 16 LSBs indicate if the -+ * corresponding ROs should be masked for this corner -+ * @irq_en: Bitmap of the CPR interrupts to enable for this corner -+ * @aging_derate: The amount to derate the aging voltage adjustment -+ * determined for the reference corner in units of uV/mV. -+ * E.g. a value of 900 would imply that the adjustment for -+ * this corner should be 90% (900/1000) of that for the -+ * reference corner. -+ * @use_open_loop: Boolean indicating that open-loop (i.e CPR disabled) as -+ * opposed to closed-loop operation must be used for this -+ * corner on CPRh controllers. -+ * @sdelta: The CPR4 controller specific data for this corner. This -+ * field is applicable for CPR4 controllers. -+ * -+ * The value of last_volt is initialized inside of the cpr3_regulator_register() -+ * call with the open_loop_volt value. It can later be updated to the settled -+ * VDD supply voltage. The values for unaged_floor_volt, unaged_ceiling_volt, -+ * and unaged_open_loop_volt are initialized inside of cpr3_regulator_register() -+ * if ctrl->aging_required == true. These three values must be pre-initialized -+ * if cpr3_regulator_register() is called with ctrl->aging_required == false and -+ * ctrl->aging_succeeded == true. -+ * -+ * The values of ro_mask and irq_en are initialized inside of the -+ * cpr3_regulator_register() call. -+ */ -+struct cpr3_corner { -+ int floor_volt; -+ int ceiling_volt; -+ int cold_temp_open_loop_volt; -+ int normal_temp_open_loop_volt; -+ int open_loop_volt; -+ int last_volt; -+ int abs_ceiling_volt; -+ int unaged_floor_volt; -+ int unaged_ceiling_volt; -+ int unaged_open_loop_volt; -+ int system_volt; -+ int mem_acc_volt; -+ u32 proc_freq; -+ int cpr_fuse_corner; -+ u32 target_quot[CPR3_RO_COUNT]; -+ u32 ro_scale[CPR3_RO_COUNT]; -+ u32 ro_mask; -+ u32 irq_en; -+ int aging_derate; -+ bool use_open_loop; -+ struct cpr4_sdelta *sdelta; -+}; -+ -+/** -+ * struct cprh_corner_band - CPRh controller specific data structure which -+ * encapsulates the range of corners and the SDELTA -+ * adjustment table to be applied to the corners within -+ * the min and max bounds of the corner band. -+ * @corner: Corner number which defines the corner band boundary -+ * @sdelta: The SDELTA adjustment table which contains core-count -+ * and temp based margin adjustments that are applicable -+ * to the corner band. -+ */ -+struct cprh_corner_band { -+ int corner; -+ struct cpr4_sdelta *sdelta; -+}; -+ -+/** -+ * struct cpr3_fuse_parameters - CPR4 fuse specific data structure which has -+ * the required fuse parameters need for Close Loop CPR -+ * @(*apss_ro_sel_param)[2]: Pointer to RO select fuse details -+ * @(*apss_init_voltage_param)[2]: Pointer to Target voltage fuse details -+ * @(*apss_target_quot_param)[2]: Pointer to Target quot fuse details -+ * @(*apss_quot_offset_param)[2]: Pointer to quot offset fuse details -+ * @cpr_fusing_rev_param: Pointer to CPR revision fuse details -+ * @apss_speed_bin_param: Pointer to Speed bin fuse details -+ * @cpr_boost_fuse_cfg_param: Pointer to Boost fuse cfg details -+ * @apss_boost_fuse_volt_param: Pointer to Boost fuse volt details -+ * @misc_fuse_volt_adj_param: Pointer to Misc fuse volt fuse details -+ */ -+struct cpr3_fuse_parameters { -+ struct cpr3_fuse_param (*apss_ro_sel_param)[2]; -+ struct cpr3_fuse_param (*apss_init_voltage_param)[2]; -+ struct cpr3_fuse_param (*apss_target_quot_param)[2]; -+ struct cpr3_fuse_param (*apss_quot_offset_param)[2]; -+ struct cpr3_fuse_param *cpr_fusing_rev_param; -+ struct cpr3_fuse_param *apss_speed_bin_param; -+ struct cpr3_fuse_param *cpr_boost_fuse_cfg_param; -+ struct cpr3_fuse_param *apss_boost_fuse_volt_param; -+ struct cpr3_fuse_param *misc_fuse_volt_adj_param; -+}; -+ -+struct cpr4_mem_acc_func { -+ void (*set_mem_acc)(struct regulator_dev *); -+ void (*clear_mem_acc)(struct regulator_dev *); -+}; -+ -+/** -+ * struct cpr4_reg_data - CPR4 regulator specific data structure which is -+ * target specific -+ * @cpr_valid_fuse_count: Number of valid fuse corners -+ * @fuse_ref_volt: Pointer to fuse reference voltage -+ * @fuse_step_volt: CPR step voltage available in fuse -+ * @cpr_clk_rate: CPR clock rate -+ * @boost_fuse_ref_volt: Boost fuse reference voltage -+ * @boost_ceiling_volt: Boost ceiling voltage -+ * @boost_floor_volt: Boost floor voltage -+ * @cpr3_fuse_params: Pointer to CPR fuse parameters -+ * @mem_acc_funcs: Pointer to MEM ACC set/clear functions -+ **/ -+struct cpr4_reg_data { -+ u32 cpr_valid_fuse_count; -+ int *fuse_ref_volt; -+ u32 fuse_step_volt; -+ u32 cpr_clk_rate; -+ int boost_fuse_ref_volt; -+ int boost_ceiling_volt; -+ int boost_floor_volt; -+ struct cpr3_fuse_parameters *cpr3_fuse_params; -+ struct cpr4_mem_acc_func *mem_acc_funcs; -+}; -+/** -+ * struct cpr3_reg_data - CPR3 regulator specific data structure which is -+ * target specific -+ * @cpr_valid_fuse_count: Number of valid fuse corners -+ * @(*init_voltage_param)[2]: Pointer to Target voltage fuse details -+ * @fuse_ref_volt: Pointer to fuse reference voltage -+ * @fuse_step_volt: CPR step voltage available in fuse -+ * @cpr_clk_rate: CPR clock rate -+ * @cpr3_fuse_params: Pointer to CPR fuse parameters -+ **/ -+struct cpr3_reg_data { -+ u32 cpr_valid_fuse_count; -+ struct cpr3_fuse_param (*init_voltage_param)[2]; -+ int *fuse_ref_volt; -+ u32 fuse_step_volt; -+ u32 cpr_clk_rate; -+}; -+ -+/** -+ * struct cpr3_regulator - CPR3 logical regulator instance associated with a -+ * given CPR3 hardware thread -+ * @of_node: Device node associated with the device tree child node -+ * of this CPR3 regulator -+ * @thread: Pointer to the CPR3 thread which manages this CPR3 -+ * regulator -+ * @name: Unique name for this CPR3 regulator which is filled -+ * using the device tree regulator-name property -+ * @rdesc: Regulator description for this CPR3 regulator -+ * @rdev: Regulator device pointer for the regulator registered -+ * for this CPR3 regulator -+ * @mem_acc_regulator: Pointer to the optional mem-acc supply regulator used -+ * to manage memory circuitry settings based upon CPR3 -+ * regulator output voltage. -+ * @corner: Array of all corners supported by this CPR3 regulator -+ * @corner_count: The number of elements in the corner array -+ * @corner_band: Array of all corner bands supported by CPRh compatible -+ * controllers -+ * @cpr4_regulator_data Target specific cpr4 regulator data -+ * @cpr3_regulator_data Target specific cpr3 regulator data -+ * @corner_band_count: The number of elements in the corner band array -+ * @platform_fuses: Pointer to platform specific CPR fuse data (only used by -+ * platform specific CPR3 driver) -+ * @speed_bin_fuse: Value read from the speed bin fuse parameter -+ * @speed_bins_supported: The number of speed bins supported by the device tree -+ * configuration for this CPR3 regulator -+ * @cpr_rev_fuse: Value read from the CPR fusing revision fuse parameter -+ * @fuse_combo: Platform specific enum value identifying the specific -+ * combination of fuse values found on a given chip -+ * @fuse_combos_supported: The number of fuse combinations supported by the -+ * device tree configuration for this CPR3 regulator -+ * @fuse_corner_count: Number of corners defined by fuse parameters -+ * @fuse_corner_map: Array of length fuse_corner_count which specifies the -+ * highest corner associated with each fuse corner. Note -+ * that each element must correspond to a valid corner -+ * and that element values must be strictly increasing. -+ * Also, it is acceptable for the lowest fuse corner to map -+ * to a corner other than the lowest. Likewise, it is -+ * acceptable for the highest fuse corner to map to a -+ * corner other than the highest. -+ * @fuse_combo_corner_sum: The sum of the corner counts across all fuse combos -+ * @fuse_combo_offset: The device tree property array offset for the selected -+ * fuse combo -+ * @speed_bin_corner_sum: The sum of the corner counts across all speed bins -+ * This may be specified as 0 if per speed bin parsing -+ * support is not required. -+ * @speed_bin_offset: The device tree property array offset for the selected -+ * speed bin -+ * @fuse_combo_corner_band_sum: The sum of the corner band counts across all -+ * fuse combos -+ * @fuse_combo_corner_band_offset: The device tree property array offset for -+ * the corner band count corresponding to the selected -+ * fuse combo -+ * @speed_bin_corner_band_sum: The sum of the corner band counts across all -+ * speed bins. This may be specified as 0 if per speed bin -+ * parsing support is not required -+ * @speed_bin_corner_band_offset: The device tree property array offset for the -+ * corner band count corresponding to the selected speed -+ * bin -+ * @pd_bypass_mask: Bit mask of power domains associated with this CPR3 -+ * regulator -+ * @dynamic_floor_corner: Index identifying the voltage corner for the CPR3 -+ * regulator whose last_volt value should be used as the -+ * global CPR floor voltage if all of the power domains -+ * associated with this CPR3 regulator are bypassed -+ * @uses_dynamic_floor: Boolean flag indicating that dynamic_floor_corner should -+ * be utilized for the CPR3 regulator -+ * @current_corner: Index identifying the currently selected voltage corner -+ * for the CPR3 regulator or less than 0 if no corner has -+ * been requested -+ * @last_closed_loop_corner: Index identifying the last voltage corner for the -+ * CPR3 regulator which was configured when operating in -+ * CPR closed-loop mode or less than 0 if no corner has -+ * been requested. CPR registers are only written to when -+ * using closed-loop mode. -+ * @aggregated: Boolean flag indicating that this CPR3 regulator -+ * participated in the last aggregation event -+ * @debug_corner: Index identifying voltage corner used for displaying -+ * corner configuration values in debugfs -+ * @vreg_enabled: Boolean defining the enable state of the CPR3 -+ * regulator's regulator within the regulator framework. -+ * @aging_allowed: Boolean defining if CPR aging adjustments are allowed -+ * for this CPR3 regulator given the fuse combo of the -+ * device -+ * @aging_allow_open_loop_adj: Boolean defining if the open-loop voltage of each -+ * corner of this regulator should be adjusted as a result -+ * of an aging measurement. This flag can be set to false -+ * when the open-loop voltage adjustments have been -+ * specified such that they include the maximum possible -+ * aging adjustment. This flag is only used if -+ * aging_allowed == true. -+ * @aging_corner: The corner that should be configured for this regulator -+ * when an aging measurement is performed. -+ * @aging_max_adjust_volt: The maximum aging voltage margin in microvolts that -+ * may be added to the target quotients of this regulator. -+ * A value of 0 may be specified if this regulator does not -+ * require any aging adjustment. -+ * @allow_core_count_adj: Core count adjustments are allowed for this regulator. -+ * @allow_temp_adj: Temperature based adjustments are allowed for this -+ * regulator. -+ * @max_core_count: Maximum number of cores considered for core count -+ * adjustment logic. -+ * @allow_boost: Voltage boost allowed for this regulator. -+ * -+ * This structure contains both configuration and runtime state data. The -+ * elements current_corner, last_closed_loop_corner, aggregated, debug_corner, -+ * and vreg_enabled are state variables. -+ */ -+struct cpr3_regulator { -+ struct device_node *of_node; -+ struct cpr3_thread *thread; -+ const char *name; -+ struct regulator_desc rdesc; -+ struct regulator_dev *rdev; -+ struct regulator *mem_acc_regulator; -+ struct cpr3_corner *corner; -+ int corner_count; -+ struct cprh_corner_band *corner_band; -+ struct cpr4_reg_data *cpr4_regulator_data; -+ struct cpr3_reg_data *cpr3_regulator_data; -+ u32 corner_band_count; -+ -+ void *platform_fuses; -+ int speed_bin_fuse; -+ int speed_bins_supported; -+ int cpr_rev_fuse; -+ int part_type; -+ int part_type_supported; -+ int fuse_combo; -+ int fuse_combos_supported; -+ int fuse_corner_count; -+ int *fuse_corner_map; -+ int fuse_combo_corner_sum; -+ int fuse_combo_offset; -+ int speed_bin_corner_sum; -+ int speed_bin_offset; -+ int fuse_combo_corner_band_sum; -+ int fuse_combo_corner_band_offset; -+ int speed_bin_corner_band_sum; -+ int speed_bin_corner_band_offset; -+ u32 pd_bypass_mask; -+ int dynamic_floor_corner; -+ bool uses_dynamic_floor; -+ -+ int current_corner; -+ int last_closed_loop_corner; -+ bool aggregated; -+ int debug_corner; -+ bool vreg_enabled; -+ -+ bool aging_allowed; -+ bool aging_allow_open_loop_adj; -+ int aging_corner; -+ int aging_max_adjust_volt; -+ -+ bool allow_core_count_adj; -+ bool allow_temp_adj; -+ int max_core_count; -+ bool allow_boost; -+}; -+ -+/** -+ * struct cpr3_thread - CPR3 hardware thread data structure -+ * @thread_id: Hardware thread ID -+ * @of_node: Device node associated with the device tree child node -+ * of this CPR3 thread -+ * @ctrl: Pointer to the CPR3 controller which manages this thread -+ * @vreg: Array of CPR3 regulators handled by the CPR3 thread -+ * @vreg_count: Number of elements in the vreg array -+ * @aggr_corner: CPR corner containing the in process aggregated voltage -+ * and target quotient configurations which will be applied -+ * @last_closed_loop_aggr_corner: CPR corner containing the most recent -+ * configurations which were written into hardware -+ * registers when operating in closed loop mode (i.e. with -+ * CPR enabled) -+ * @consecutive_up: The number of consecutive CPR step up events needed to -+ * to trigger an up interrupt -+ * @consecutive_down: The number of consecutive CPR step down events needed to -+ * to trigger a down interrupt -+ * @up_threshold: The number CPR error steps required to generate an up -+ * event -+ * @down_threshold: The number CPR error steps required to generate a down -+ * event -+ * -+ * This structure contains both configuration and runtime state data. The -+ * elements aggr_corner and last_closed_loop_aggr_corner are state variables. -+ */ -+struct cpr3_thread { -+ u32 thread_id; -+ struct device_node *of_node; -+ struct cpr3_controller *ctrl; -+ struct cpr3_regulator *vreg; -+ int vreg_count; -+ struct cpr3_corner aggr_corner; -+ struct cpr3_corner last_closed_loop_aggr_corner; -+ -+ u32 consecutive_up; -+ u32 consecutive_down; -+ u32 up_threshold; -+ u32 down_threshold; -+}; -+ -+/* Per CPR controller data */ -+/** -+ * enum cpr3_mem_acc_corners - Constants which define the number of mem-acc -+ * regulator corners available in the mem-acc corner map array. -+ * %CPR3_MEM_ACC_LOW_CORNER: Index in mem-acc corner map array mapping to the -+ * mem-acc regulator corner -+ * to be used for low voltage vdd supply -+ * %CPR3_MEM_ACC_HIGH_CORNER: Index in mem-acc corner map array mapping to the -+ * mem-acc regulator corner to be used for high -+ * voltage vdd supply -+ * %CPR3_MEM_ACC_CORNERS: Number of elements in the mem-acc corner map -+ * array -+ */ -+enum cpr3_mem_acc_corners { -+ CPR3_MEM_ACC_LOW_CORNER = 0, -+ CPR3_MEM_ACC_HIGH_CORNER = 1, -+ CPR3_MEM_ACC_CORNERS = 2, -+}; -+ -+/** -+ * enum cpr3_count_mode - CPR3 controller count mode which defines the -+ * method that CPR sensor data is acquired -+ * %CPR3_COUNT_MODE_ALL_AT_ONCE_MIN: Capture all CPR sensor readings -+ * simultaneously and report the minimum -+ * value seen in successive measurements -+ * %CPR3_COUNT_MODE_ALL_AT_ONCE_MAX: Capture all CPR sensor readings -+ * simultaneously and report the maximum -+ * value seen in successive measurements -+ * %CPR3_COUNT_MODE_STAGGERED: Read one sensor at a time in a -+ * sequential fashion -+ * %CPR3_COUNT_MODE_ALL_AT_ONCE_AGE: Capture all CPR aging sensor readings -+ * simultaneously. -+ */ -+enum cpr3_count_mode { -+ CPR3_COUNT_MODE_ALL_AT_ONCE_MIN = 0, -+ CPR3_COUNT_MODE_ALL_AT_ONCE_MAX = 1, -+ CPR3_COUNT_MODE_STAGGERED = 2, -+ CPR3_COUNT_MODE_ALL_AT_ONCE_AGE = 3, -+}; -+ -+/** -+ * enum cpr_controller_type - supported CPR controller hardware types -+ * %CPR_CTRL_TYPE_CPR3: HW has CPR3 controller -+ * %CPR_CTRL_TYPE_CPR4: HW has CPR4 controller -+ */ -+enum cpr_controller_type { -+ CPR_CTRL_TYPE_CPR3, -+ CPR_CTRL_TYPE_CPR4, -+}; -+ -+/** -+ * cpr_setting - supported CPR global settings -+ * %CPR_DEFAULT: default mode from dts will be used -+ * %CPR_DISABLED: ceiling voltage will be used for all the corners -+ * %CPR_OPEN_LOOP_EN: CPR will work in OL -+ * %CPR_CLOSED_LOOP_EN: CPR will work in CL, if supported -+ */ -+enum cpr_setting { -+ CPR_DEFAULT = 0, -+ CPR_DISABLED = 1, -+ CPR_OPEN_LOOP_EN = 2, -+ CPR_CLOSED_LOOP_EN = 3, -+}; -+ -+/** -+ * struct cpr3_aging_sensor_info - CPR3 aging sensor information -+ * @sensor_id The index of the CPR3 sensor to be used in the aging -+ * measurement. -+ * @ro_scale The CPR ring oscillator (RO) scaling factor for the -+ * aging sensor with units of QUOT/V. -+ * @init_quot_diff: The fused quotient difference between aged and un-aged -+ * paths that was measured at manufacturing time. -+ * @measured_quot_diff: The quotient difference measured at runtime. -+ * @bypass_mask: Bit mask of the CPR sensors that must be bypassed during -+ * the aging measurement for this sensor -+ * -+ * This structure contains both configuration and runtime state data. The -+ * element measured_quot_diff is a state variable. -+ */ -+struct cpr3_aging_sensor_info { -+ u32 sensor_id; -+ u32 ro_scale; -+ int init_quot_diff; -+ int measured_quot_diff; -+ u32 bypass_mask[CPR3_MAX_SENSOR_COUNT / 32]; -+}; -+ -+/** -+ * struct cpr3_reg_info - Register information data structure -+ * @name: Register name -+ * @addr: Register physical address -+ * @value: Register content -+ * @virt_addr: Register virtual address -+ * -+ * This data structure is used to dump some critical register contents -+ * when the device crashes due to a kernel panic. -+ */ -+struct cpr3_reg_info { -+ const char *name; -+ u32 addr; -+ u32 value; -+ void __iomem *virt_addr; -+}; -+ -+/** -+ * struct cpr3_panic_regs_info - Data structure to dump critical register -+ * contents. -+ * @reg_count: Number of elements in the regs array -+ * @regs: Array of critical registers information -+ * -+ * This data structure is used to dump critical register contents when -+ * the device crashes due to a kernel panic. -+ */ -+struct cpr3_panic_regs_info { -+ int reg_count; -+ struct cpr3_reg_info *regs; -+}; -+ -+/** -+ * struct cpr3_controller - CPR3 controller data structure -+ * @dev: Device pointer for the CPR3 controller device -+ * @name: Unique name for the CPR3 controller -+ * @ctrl_id: Controller ID corresponding to the VDD supply number -+ * that this CPR3 controller manages. -+ * @cpr_ctrl_base: Virtual address of the CPR3 controller base register -+ * @fuse_base: Virtual address of fuse row 0 -+ * @aging_possible_reg: Virtual address of an optional platform-specific -+ * register that must be ready to determine if it is -+ * possible to perform an aging measurement. -+ * @list: list head used in a global cpr3-regulator list so that -+ * cpr3-regulator structs can be found easily in RAM dumps -+ * @thread: Array of CPR3 threads managed by the CPR3 controller -+ * @thread_count: Number of elements in the thread array -+ * @sensor_owner: Array of thread IDs indicating which thread owns a given -+ * CPR sensor -+ * @sensor_count: The number of CPR sensors found on the CPR loop managed -+ * by this CPR controller. Must be equal to the number of -+ * elements in the sensor_owner array -+ * @soc_revision: Revision number of the SoC. This may be unused by -+ * platforms that do not have different behavior for -+ * different SoC revisions. -+ * @lock: Mutex lock used to ensure mutual exclusion between -+ * all of the threads associated with the controller -+ * @vdd_regulator: Pointer to the VDD supply regulator which this CPR3 -+ * controller manages -+ * @system_regulator: Pointer to the optional system-supply regulator upon -+ * which the VDD supply regulator depends. -+ * @mem_acc_regulator: Pointer to the optional mem-acc supply regulator used -+ * to manage memory circuitry settings based upon the -+ * VDD supply output voltage. -+ * @vdd_limit_regulator: Pointer to the VDD supply limit regulator which is used -+ * for hardware closed-loop in order specify ceiling and -+ * floor voltage limits (platform specific) -+ * @system_supply_max_volt: Voltage in microvolts which corresponds to the -+ * absolute ceiling voltage of the system-supply -+ * @mem_acc_threshold_volt: mem-acc threshold voltage in microvolts -+ * @mem_acc_corner_map: mem-acc regulator corners mapping to low and high -+ * voltage mem-acc settings for the memories powered by -+ * this CPR3 controller and its associated CPR3 regulators -+ * @mem_acc_crossover_volt: Voltage in microvolts corresponding to the voltage -+ * that the VDD supply must be set to while a MEM ACC -+ * switch is in progress. This element must be initialized -+ * for CPRh controllers when a MEM ACC threshold voltage is -+ * defined. -+ * @core_clk: Pointer to the CPR3 controller core clock -+ * @iface_clk: Pointer to the CPR3 interface clock (platform specific) -+ * @bus_clk: Pointer to the CPR3 bus clock (platform specific) -+ * @irq: CPR interrupt number -+ * @irq_affinity_mask: The cpumask for the CPUs which the CPR interrupt should -+ * have affinity for -+ * @cpu_hotplug_notifier: CPU hotplug notifier used to reset IRQ affinity when a -+ * CPU is brought back online -+ * @ceiling_irq: Interrupt number for the interrupt that is triggered -+ * when hardware closed-loop attempts to exceed the ceiling -+ * voltage -+ * @apm: Handle to the array power mux (APM) -+ * @apm_threshold_volt: Voltage in microvolts which defines the threshold -+ * voltage to determine the APM supply selection for -+ * each corner -+ * @apm_crossover_volt: Voltage in microvolts corresponding to the voltage that -+ * the VDD supply must be set to while an APM switch is in -+ * progress. This element must be initialized for CPRh -+ * controllers when an APM threshold voltage is defined -+ * @apm_adj_volt: Minimum difference between APM threshold voltage and -+ * open-loop voltage which allows the APM threshold voltage -+ * to be used as a ceiling -+ * @apm_high_supply: APM supply to configure if VDD voltage is greater than -+ * or equal to the APM threshold voltage -+ * @apm_low_supply: APM supply to configure if the VDD voltage is less than -+ * the APM threshold voltage -+ * @base_volt: Minimum voltage in microvolts supported by the VDD -+ * supply managed by this CPR controller -+ * @corner_switch_delay_time: The delay time in nanoseconds used by the CPR -+ * controller to wait for voltage settling before -+ * acknowledging the OSM block after corner changes -+ * @cpr_clock_rate: CPR reference clock frequency in Hz. -+ * @sensor_time: The time in nanoseconds that each sensor takes to -+ * perform a measurement. -+ * @loop_time: The time in nanoseconds between consecutive CPR -+ * measurements. -+ * @up_down_delay_time: The time to delay in nanoseconds between consecutive CPR -+ * measurements when the last measurement recommended -+ * increasing or decreasing the vdd-supply voltage. -+ * (platform specific) -+ * @idle_clocks: Number of CPR reference clock ticks that the CPR -+ * controller waits in transitional states. -+ * @step_quot_init_min: The default minimum CPR step quotient value. The step -+ * quotient is the number of additional ring oscillator -+ * ticks observed when increasing one step in vdd-supply -+ * output voltage. -+ * @step_quot_init_max: The default maximum CPR step quotient value. -+ * @step_volt: Step size in microvolts between available set points -+ * of the VDD supply -+ * @down_error_step_limit: CPR4 hardware closed-loop down error step limit which -+ * defines the maximum number of VDD supply regulator steps -+ * that the voltage may be reduced as the result of a -+ * single CPR measurement. -+ * @up_error_step_limit: CPR4 hardware closed-loop up error step limit which -+ * defines the maximum number of VDD supply regulator steps -+ * that the voltage may be increased as the result of a -+ * single CPR measurement. -+ * @count_mode: CPR controller count mode -+ * @count_repeat: Number of times to perform consecutive sensor -+ * measurements when using all-at-once count modes. -+ * @proc_clock_throttle: Defines the processor clock frequency throttling -+ * register value to use. This can be used to reduce the -+ * clock frequency when a power domain exits a low power -+ * mode until CPR settles at a new voltage. -+ * (platform specific) -+ * @cpr_allowed_hw: Boolean which indicates if closed-loop CPR operation is -+ * permitted for a given chip based upon hardware fuse -+ * values -+ * @cpr_allowed_sw: Boolean which indicates if closed-loop CPR operation is -+ * permitted based upon software policies -+ * @supports_hw_closed_loop: Boolean which indicates if this CPR3/4 controller -+ * physically supports hardware closed-loop CPR operation -+ * @use_hw_closed_loop: Boolean which indicates that this controller will be -+ * using hardware closed-loop operation in place of -+ * software closed-loop operation. -+ * @ctrl_type: CPR controller type -+ * @saw_use_unit_mV: Boolean which indicates the unit used in SAW PVC -+ * interface is mV. -+ * @aggr_corner: CPR corner containing the most recently aggregated -+ * voltage configurations which are being used currently -+ * @cpr_enabled: Boolean which indicates that the CPR controller is -+ * enabled and operating in closed-loop mode. CPR clocks -+ * have been prepared and enabled whenever this flag is -+ * true. -+ * @last_corner_was_closed_loop: Boolean indicating if the last known corners -+ * were updated during closed loop operation. -+ * @cpr_suspended: Boolean which indicates that CPR has been temporarily -+ * disabled while enterring system suspend. -+ * @debugfs: Pointer to the debugfs directory of this CPR3 controller -+ * @aging_ref_volt: Reference voltage in microvolts to configure when -+ * performing CPR aging measurements. -+ * @aging_vdd_mode: vdd-supply regulator mode to configure before performing -+ * a CPR aging measurement. It should be one of -+ * REGULATOR_MODE_*. -+ * @aging_complete_vdd_mode: vdd-supply regulator mode to configure after -+ * performing a CPR aging measurement. It should be one of -+ * REGULATOR_MODE_*. -+ * @aging_ref_adjust_volt: The reference aging voltage margin in microvolts that -+ * should be added to the target quotients of the -+ * regulators managed by this controller after derating. -+ * @aging_required: Flag which indicates that a CPR aging measurement still -+ * needs to be performed for this CPR3 controller. -+ * @aging_succeeded: Flag which indicates that a CPR aging measurement has -+ * completed successfully. -+ * @aging_failed: Flag which indicates that a CPR aging measurement has -+ * failed to complete successfully. -+ * @aging_sensor: Array of CPR3 aging sensors which are used to perform -+ * aging measurements at a runtime. -+ * @aging_sensor_count: Number of elements in the aging_sensor array -+ * @aging_possible_mask: Optional bitmask used to mask off the -+ * aging_possible_reg register. -+ * @aging_possible_val: Optional value that the masked aging_possible_reg -+ * register must have in order for a CPR aging measurement -+ * to be possible. -+ * @step_quot_fixed: Fixed step quotient value used for target quotient -+ * adjustment if use_dynamic_step_quot is not set. -+ * This parameter is only relevant for CPR4 controllers -+ * when using the per-online-core or per-temperature -+ * adjustments. -+ * @initial_temp_band: Temperature band used for calculation of base-line -+ * target quotients (fused). -+ * @use_dynamic_step_quot: Boolean value which indicates that margin adjustment -+ * of target quotient will be based on the step quotient -+ * calculated dynamically in hardware for each RO. -+ * @allow_core_count_adj: Core count adjustments are allowed for this controller -+ * @allow_temp_adj: Temperature based adjustments are allowed for -+ * this controller -+ * @allow_boost: Voltage boost allowed for this controller. -+ * @temp_band_count: Number of temperature bands used for temperature based -+ * adjustment logic -+ * @temp_points: Array of temperature points in decidegrees Celsius used -+ * to specify the ranges for selected temperature bands. -+ * The array must have (temp_band_count - 1) elements -+ * allocated. -+ * @temp_sensor_id_start: Start ID of temperature sensors used for temperature -+ * based adjustments. -+ * @temp_sensor_id_end: End ID of temperature sensors used for temperature -+ * based adjustments. -+ * @voltage_settling_time: The time in nanoseconds that it takes for the -+ * VDD supply voltage to settle after being increased or -+ * decreased by step_volt microvolts which is used when -+ * SDELTA voltage margin adjustments are applied. -+ * @cpr_global_setting: Global setting for this CPR controller -+ * @panic_regs_info: Array of panic registers information which provides the -+ * list of registers to dump when the device crashes. -+ * @panic_notifier: Notifier block registered to global panic notifier list. -+ * -+ * This structure contains both configuration and runtime state data. The -+ * elements cpr_allowed_sw, use_hw_closed_loop, aggr_corner, cpr_enabled, -+ * last_corner_was_closed_loop, cpr_suspended, aging_ref_adjust_volt, -+ * aging_required, aging_succeeded, and aging_failed are state variables. -+ * -+ * The apm* elements do not need to be initialized if the VDD supply managed by -+ * the CPR3 controller does not utilize an APM. -+ * -+ * The elements step_quot_fixed, initial_temp_band, allow_core_count_adj, -+ * allow_temp_adj and temp* need to be initialized for CPR4 controllers which -+ * are using per-online-core or per-temperature adjustments. -+ */ -+struct cpr3_controller { -+ struct device *dev; -+ const char *name; -+ int ctrl_id; -+ void __iomem *cpr_ctrl_base; -+ void __iomem *fuse_base; -+ void __iomem *aging_possible_reg; -+ struct list_head list; -+ struct cpr3_thread *thread; -+ int thread_count; -+ u8 *sensor_owner; -+ int sensor_count; -+ int soc_revision; -+ struct mutex lock; -+ struct regulator *vdd_regulator; -+ struct regulator *system_regulator; -+ struct regulator *mem_acc_regulator; -+ struct regulator *vdd_limit_regulator; -+ int system_supply_max_volt; -+ int mem_acc_threshold_volt; -+ int mem_acc_corner_map[CPR3_MEM_ACC_CORNERS]; -+ int mem_acc_crossover_volt; -+ struct clk *core_clk; -+ struct clk *iface_clk; -+ struct clk *bus_clk; -+ int irq; -+ struct cpumask irq_affinity_mask; -+ struct notifier_block cpu_hotplug_notifier; -+ int ceiling_irq; -+ struct msm_apm_ctrl_dev *apm; -+ int apm_threshold_volt; -+ int apm_crossover_volt; -+ int apm_adj_volt; -+ enum msm_apm_supply apm_high_supply; -+ enum msm_apm_supply apm_low_supply; -+ int base_volt; -+ u32 corner_switch_delay_time; -+ u32 cpr_clock_rate; -+ u32 sensor_time; -+ u32 loop_time; -+ u32 up_down_delay_time; -+ u32 idle_clocks; -+ u32 step_quot_init_min; -+ u32 step_quot_init_max; -+ int step_volt; -+ u32 down_error_step_limit; -+ u32 up_error_step_limit; -+ enum cpr3_count_mode count_mode; -+ u32 count_repeat; -+ u32 proc_clock_throttle; -+ bool cpr_allowed_hw; -+ bool cpr_allowed_sw; -+ bool supports_hw_closed_loop; -+ bool use_hw_closed_loop; -+ enum cpr_controller_type ctrl_type; -+ bool saw_use_unit_mV; -+ struct cpr3_corner aggr_corner; -+ bool cpr_enabled; -+ bool last_corner_was_closed_loop; -+ bool cpr_suspended; -+ struct dentry *debugfs; -+ -+ int aging_ref_volt; -+ unsigned int aging_vdd_mode; -+ unsigned int aging_complete_vdd_mode; -+ int aging_ref_adjust_volt; -+ bool aging_required; -+ bool aging_succeeded; -+ bool aging_failed; -+ struct cpr3_aging_sensor_info *aging_sensor; -+ int aging_sensor_count; -+ u32 cur_sensor_state; -+ u32 aging_possible_mask; -+ u32 aging_possible_val; -+ -+ u32 step_quot_fixed; -+ u32 initial_temp_band; -+ bool use_dynamic_step_quot; -+ bool allow_core_count_adj; -+ bool allow_temp_adj; -+ bool allow_boost; -+ int temp_band_count; -+ int *temp_points; -+ u32 temp_sensor_id_start; -+ u32 temp_sensor_id_end; -+ u32 voltage_settling_time; -+ enum cpr_setting cpr_global_setting; -+ struct cpr3_panic_regs_info *panic_regs_info; -+ struct notifier_block panic_notifier; -+}; -+ -+/* Used for rounding voltages to the closest physically available set point. */ -+#define CPR3_ROUND(n, d) (DIV_ROUND_UP(n, d) * (d)) -+ -+#define cpr3_err(cpr3_thread, message, ...) \ -+ pr_err("%s: " message, (cpr3_thread)->name, ##__VA_ARGS__) -+#define cpr3_info(cpr3_thread, message, ...) \ -+ pr_info("%s: " message, (cpr3_thread)->name, ##__VA_ARGS__) -+#define cpr3_debug(cpr3_thread, message, ...) \ -+ pr_debug("%s: " message, (cpr3_thread)->name, ##__VA_ARGS__) -+ -+/* -+ * Offset subtracted from voltage corner values passed in from the regulator -+ * framework in order to get internal voltage corner values. This is needed -+ * since the regulator framework treats 0 as an error value at regulator -+ * registration time. -+ */ -+#define CPR3_CORNER_OFFSET 1 -+ -+#ifdef CONFIG_REGULATOR_CPR3 -+ -+int cpr3_regulator_register(struct platform_device *pdev, -+ struct cpr3_controller *ctrl); -+int cpr3_open_loop_regulator_register(struct platform_device *pdev, -+ struct cpr3_controller *ctrl); -+int cpr3_regulator_unregister(struct cpr3_controller *ctrl); -+int cpr3_open_loop_regulator_unregister(struct cpr3_controller *ctrl); -+int cpr3_regulator_suspend(struct cpr3_controller *ctrl); -+int cpr3_regulator_resume(struct cpr3_controller *ctrl); -+ -+int cpr3_allocate_threads(struct cpr3_controller *ctrl, u32 min_thread_id, -+ u32 max_thread_id); -+int cpr3_map_fuse_base(struct cpr3_controller *ctrl, -+ struct platform_device *pdev); -+int cpr3_read_tcsr_setting(struct cpr3_controller *ctrl, -+ struct platform_device *pdev, u8 start, u8 end); -+int cpr3_read_fuse_param(void __iomem *fuse_base_addr, -+ const struct cpr3_fuse_param *param, u64 *param_value); -+int cpr3_convert_open_loop_voltage_fuse(int ref_volt, int step_volt, u32 fuse, -+ int fuse_len); -+u64 cpr3_interpolate(u64 x1, u64 y1, u64 x2, u64 y2, u64 x); -+int cpr3_parse_array_property(struct cpr3_regulator *vreg, -+ const char *prop_name, int tuple_size, u32 *out); -+int cpr3_parse_corner_array_property(struct cpr3_regulator *vreg, -+ const char *prop_name, int tuple_size, u32 *out); -+int cpr3_parse_corner_band_array_property(struct cpr3_regulator *vreg, -+ const char *prop_name, int tuple_size, u32 *out); -+int cpr3_parse_common_corner_data(struct cpr3_regulator *vreg); -+int cpr3_parse_thread_u32(struct cpr3_thread *thread, const char *propname, -+ u32 *out_value, u32 value_min, u32 value_max); -+int cpr3_parse_ctrl_u32(struct cpr3_controller *ctrl, const char *propname, -+ u32 *out_value, u32 value_min, u32 value_max); -+int cpr3_parse_common_thread_data(struct cpr3_thread *thread); -+int cpr3_parse_common_ctrl_data(struct cpr3_controller *ctrl); -+int cpr3_parse_open_loop_common_ctrl_data(struct cpr3_controller *ctrl); -+int cpr3_limit_open_loop_voltages(struct cpr3_regulator *vreg); -+void cpr3_open_loop_voltage_as_ceiling(struct cpr3_regulator *vreg); -+int cpr3_limit_floor_voltages(struct cpr3_regulator *vreg); -+void cpr3_print_quots(struct cpr3_regulator *vreg); -+int cpr3_determine_part_type(struct cpr3_regulator *vreg, int fuse_volt); -+int cpr3_determine_temp_base_open_loop_correction(struct cpr3_regulator *vreg, -+ int *fuse_volt); -+int cpr3_adjust_fused_open_loop_voltages(struct cpr3_regulator *vreg, -+ int *fuse_volt); -+int cpr3_adjust_open_loop_voltages(struct cpr3_regulator *vreg); -+int cpr3_quot_adjustment(int ro_scale, int volt_adjust); -+int cpr3_voltage_adjustment(int ro_scale, int quot_adjust); -+int cpr3_parse_closed_loop_voltage_adjustments(struct cpr3_regulator *vreg, -+ u64 *ro_sel, int *volt_adjust, -+ int *volt_adjust_fuse, int *ro_scale); -+int cpr4_parse_core_count_temp_voltage_adj(struct cpr3_regulator *vreg, -+ bool use_corner_band); -+int cpr3_apm_init(struct cpr3_controller *ctrl); -+int cpr3_mem_acc_init(struct cpr3_regulator *vreg); -+void cprh_adjust_voltages_for_apm(struct cpr3_regulator *vreg); -+void cprh_adjust_voltages_for_mem_acc(struct cpr3_regulator *vreg); -+int cpr3_adjust_target_quotients(struct cpr3_regulator *vreg, -+ int *fuse_volt_adjust); -+int cpr3_handle_temp_open_loop_adjustment(struct cpr3_controller *ctrl, -+ bool is_cold); -+int cpr3_get_cold_temp_threshold(struct cpr3_regulator *vreg, int *cold_temp); -+bool cpr3_can_adjust_cold_temp(struct cpr3_regulator *vreg); -+ -+#else -+ -+static inline int cpr3_regulator_register(struct platform_device *pdev, -+ struct cpr3_controller *ctrl) -+{ -+ return -ENXIO; -+} -+ -+static inline int -+cpr3_open_loop_regulator_register(struct platform_device *pdev, -+ struct cpr3_controller *ctrl); -+{ -+ return -ENXIO; -+} -+ -+static inline int cpr3_regulator_unregister(struct cpr3_controller *ctrl) -+{ -+ return -ENXIO; -+} -+ -+static inline int -+cpr3_open_loop_regulator_unregister(struct cpr3_controller *ctrl) -+{ -+ return -ENXIO; -+} -+ -+static inline int cpr3_regulator_suspend(struct cpr3_controller *ctrl) -+{ -+ return -ENXIO; -+} -+ -+static inline int cpr3_regulator_resume(struct cpr3_controller *ctrl) -+{ -+ return -ENXIO; -+} -+ -+static inline int cpr3_get_thread_name(struct cpr3_thread *thread, -+ struct device_node *thread_node) -+{ -+ return -EPERM; -+} -+ -+static inline int cpr3_allocate_threads(struct cpr3_controller *ctrl, -+ u32 min_thread_id, u32 max_thread_id) -+{ -+ return -EPERM; -+} -+ -+static inline int cpr3_map_fuse_base(struct cpr3_controller *ctrl, -+ struct platform_device *pdev) -+{ -+ return -ENXIO; -+} -+ -+static inline int cpr3_read_tcsr_setting(struct cpr3_controller *ctrl, -+ struct platform_device *pdev, u8 start, u8 end) -+{ -+ return 0; -+} -+ -+static inline int cpr3_read_fuse_param(void __iomem *fuse_base_addr, -+ const struct cpr3_fuse_param *param, u64 *param_value) -+{ -+ return -EPERM; -+} -+ -+static inline int cpr3_convert_open_loop_voltage_fuse(int ref_volt, -+ int step_volt, u32 fuse, int fuse_len) -+{ -+ return -EPERM; -+} -+ -+static inline u64 cpr3_interpolate(u64 x1, u64 y1, u64 x2, u64 y2, u64 x) -+{ -+ return 0; -+} -+ -+static inline int cpr3_parse_array_property(struct cpr3_regulator *vreg, -+ const char *prop_name, int tuple_size, u32 *out) -+{ -+ return -EPERM; -+} -+ -+static inline int cpr3_parse_corner_array_property(struct cpr3_regulator *vreg, -+ const char *prop_name, int tuple_size, u32 *out) -+{ -+ return -EPERM; -+} -+ -+static inline int cpr3_parse_corner_band_array_property( -+ struct cpr3_regulator *vreg, const char *prop_name, -+ int tuple_size, u32 *out) -+{ -+ return -EPERM; -+} -+ -+static inline int cpr3_parse_common_corner_data(struct cpr3_regulator *vreg) -+{ -+ return -EPERM; -+} -+ -+static inline int cpr3_parse_thread_u32(struct cpr3_thread *thread, -+ const char *propname, u32 *out_value, u32 value_min, -+ u32 value_max) -+{ -+ return -EPERM; -+} -+ -+static inline int cpr3_parse_ctrl_u32(struct cpr3_controller *ctrl, -+ const char *propname, u32 *out_value, u32 value_min, -+ u32 value_max) -+{ -+ return -EPERM; -+} -+ -+static inline int cpr3_parse_common_thread_data(struct cpr3_thread *thread) -+{ -+ return -EPERM; -+} -+ -+static inline int cpr3_parse_common_ctrl_data(struct cpr3_controller *ctrl) -+{ -+ return -EPERM; -+} -+ -+static inline int -+cpr3_parse_open_loop_common_ctrl_data(struct cpr3_controller *ctrl) -+{ -+ return -EPERM; -+} -+ -+static inline int cpr3_limit_open_loop_voltages(struct cpr3_regulator *vreg) -+{ -+ return -EPERM; -+} -+ -+static inline void cpr3_open_loop_voltage_as_ceiling( -+ struct cpr3_regulator *vreg) -+{ -+ return; -+} -+ -+static inline int cpr3_limit_floor_voltages(struct cpr3_regulator *vreg) -+{ -+ return -EPERM; -+} -+ -+static inline void cpr3_print_quots(struct cpr3_regulator *vreg) -+{ -+ return; -+} -+ -+static inline int -+cpr3_determine_part_type(struct cpr3_regulator *vreg, int fuse_volt) -+{ -+ return -EPERM; -+} -+ -+static inline int -+cpr3_determine_temp_base_open_loop_correction(struct cpr3_regulator *vreg, -+ int *fuse_volt) -+{ -+ return -EPERM; -+} -+ -+static inline int cpr3_adjust_fused_open_loop_voltages( -+ struct cpr3_regulator *vreg, int *fuse_volt) -+{ -+ return -EPERM; -+} -+ -+static inline int cpr3_adjust_open_loop_voltages(struct cpr3_regulator *vreg) -+{ -+ return -EPERM; -+} -+ -+static inline int cpr3_quot_adjustment(int ro_scale, int volt_adjust) -+{ -+ return 0; -+} -+ -+static inline int cpr3_voltage_adjustment(int ro_scale, int quot_adjust) -+{ -+ return 0; -+} -+ -+static inline int cpr3_parse_closed_loop_voltage_adjustments( -+ struct cpr3_regulator *vreg, u64 *ro_sel, -+ int *volt_adjust, int *volt_adjust_fuse, int *ro_scale) -+{ -+ return 0; -+} -+ -+static inline int cpr4_parse_core_count_temp_voltage_adj( -+ struct cpr3_regulator *vreg, bool use_corner_band) -+{ -+ return 0; -+} -+ -+static inline int cpr3_apm_init(struct cpr3_controller *ctrl) -+{ -+ return 0; -+} -+ -+static inline int cpr3_mem_acc_init(struct cpr3_regulator *vreg) -+{ -+ return 0; -+} -+ -+static inline void cprh_adjust_voltages_for_apm(struct cpr3_regulator *vreg) -+{ -+} -+ -+static inline void cprh_adjust_voltages_for_mem_acc(struct cpr3_regulator *vreg) -+{ -+} -+ -+static inline int cpr3_adjust_target_quotients(struct cpr3_regulator *vreg, -+ int *fuse_volt_adjust) -+{ -+ return 0; -+} -+ -+static inline int -+cpr3_handle_temp_open_loop_adjustment(struct cpr3_controller *ctrl, -+ bool is_cold) -+{ -+ return 0; -+} -+ -+static inline bool -+cpr3_can_adjust_cold_temp(struct cpr3_regulator *vreg) -+{ -+ return false; -+} -+ -+static inline int -+cpr3_get_cold_temp_threshold(struct cpr3_regulator *vreg, int *cold_temp) -+{ -+ return 0; -+} -+#endif /* CONFIG_REGULATOR_CPR3 */ -+ -+#endif /* __REGULATOR_CPR_REGULATOR_H__ */ ---- /dev/null -+++ b/drivers/regulator/cpr3-util.c -@@ -0,0 +1,2750 @@ -+/* -+ * Copyright (c) 2015-2017, The Linux Foundation. All rights reserved. -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 and -+ * only version 2 as published by the Free Software Foundation. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ */ -+ -+/* -+ * This file contains utility functions to be used by platform specific CPR3 -+ * regulator drivers. -+ */ -+ -+#define pr_fmt(fmt) "%s: " fmt, __func__ -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#include -+ -+#include "cpr3-regulator.h" -+ -+#define BYTES_PER_FUSE_ROW 8 -+#define MAX_FUSE_ROW_BIT 63 -+ -+#define CPR3_CONSECUTIVE_UP_DOWN_MIN 0 -+#define CPR3_CONSECUTIVE_UP_DOWN_MAX 15 -+#define CPR3_UP_DOWN_THRESHOLD_MIN 0 -+#define CPR3_UP_DOWN_THRESHOLD_MAX 31 -+#define CPR3_STEP_QUOT_MIN 0 -+#define CPR3_STEP_QUOT_MAX 63 -+#define CPR3_IDLE_CLOCKS_MIN 0 -+#define CPR3_IDLE_CLOCKS_MAX 31 -+ -+/* This constant has units of uV/mV so 1000 corresponds to 100%. */ -+#define CPR3_AGING_DERATE_UNITY 1000 -+ -+/** -+ * cpr3_allocate_regulators() - allocate and initialize CPR3 regulators for a -+ * given thread based upon device tree data -+ * @thread: Pointer to the CPR3 thread -+ * -+ * This function allocates the thread->vreg array based upon the number of -+ * device tree regulator subnodes. It also initializes generic elements of each -+ * regulator struct such as name, of_node, and thread. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_allocate_regulators(struct cpr3_thread *thread) -+{ -+ struct device_node *node; -+ int i, rc; -+ -+ thread->vreg_count = 0; -+ -+ for_each_available_child_of_node(thread->of_node, node) { -+ thread->vreg_count++; -+ } -+ -+ thread->vreg = devm_kcalloc(thread->ctrl->dev, thread->vreg_count, -+ sizeof(*thread->vreg), GFP_KERNEL); -+ if (!thread->vreg) -+ return -ENOMEM; -+ -+ i = 0; -+ for_each_available_child_of_node(thread->of_node, node) { -+ thread->vreg[i].of_node = node; -+ thread->vreg[i].thread = thread; -+ -+ rc = of_property_read_string(node, "regulator-name", -+ &thread->vreg[i].name); -+ if (rc) { -+ dev_err(thread->ctrl->dev, "could not find regulator name, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ i++; -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr3_allocate_threads() - allocate and initialize CPR3 threads for a given -+ * controller based upon device tree data -+ * @ctrl: Pointer to the CPR3 controller -+ * @min_thread_id: Minimum allowed hardware thread ID for this controller -+ * @max_thread_id: Maximum allowed hardware thread ID for this controller -+ * -+ * This function allocates the ctrl->thread array based upon the number of -+ * device tree thread subnodes. It also initializes generic elements of each -+ * thread struct such as thread_id, of_node, ctrl, and vreg array. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_allocate_threads(struct cpr3_controller *ctrl, u32 min_thread_id, -+ u32 max_thread_id) -+{ -+ struct device *dev = ctrl->dev; -+ struct device_node *thread_node; -+ int i, j, rc; -+ -+ ctrl->thread_count = 0; -+ -+ for_each_available_child_of_node(dev->of_node, thread_node) { -+ ctrl->thread_count++; -+ } -+ -+ ctrl->thread = devm_kcalloc(dev, ctrl->thread_count, -+ sizeof(*ctrl->thread), GFP_KERNEL); -+ if (!ctrl->thread) -+ return -ENOMEM; -+ -+ i = 0; -+ for_each_available_child_of_node(dev->of_node, thread_node) { -+ ctrl->thread[i].of_node = thread_node; -+ ctrl->thread[i].ctrl = ctrl; -+ -+ rc = of_property_read_u32(thread_node, "qcom,cpr-thread-id", -+ &ctrl->thread[i].thread_id); -+ if (rc) { -+ dev_err(dev, "could not read DT property qcom,cpr-thread-id, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ if (ctrl->thread[i].thread_id < min_thread_id || -+ ctrl->thread[i].thread_id > max_thread_id) { -+ dev_err(dev, "invalid thread id = %u; not within [%u, %u]\n", -+ ctrl->thread[i].thread_id, min_thread_id, -+ max_thread_id); -+ return -EINVAL; -+ } -+ -+ /* Verify that the thread ID is unique for all child nodes. */ -+ for (j = 0; j < i; j++) { -+ if (ctrl->thread[j].thread_id -+ == ctrl->thread[i].thread_id) { -+ dev_err(dev, "duplicate thread id = %u found\n", -+ ctrl->thread[i].thread_id); -+ return -EINVAL; -+ } -+ } -+ -+ rc = cpr3_allocate_regulators(&ctrl->thread[i]); -+ if (rc) -+ return rc; -+ -+ i++; -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr3_map_fuse_base() - ioremap the base address of the fuse region -+ * @ctrl: Pointer to the CPR3 controller -+ * @pdev: Platform device pointer for the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_map_fuse_base(struct cpr3_controller *ctrl, -+ struct platform_device *pdev) -+{ -+ struct resource *res; -+ -+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "fuse_base"); -+ if (!res || !res->start) { -+ dev_err(&pdev->dev, "fuse base address is missing\n"); -+ return -ENXIO; -+ } -+ -+ ctrl->fuse_base = devm_ioremap(&pdev->dev, res->start, -+ resource_size(res)); -+ -+ return 0; -+} -+ -+/** -+ * cpr3_read_tcsr_setting - reads the CPR setting bits from TCSR register -+ * @ctrl: Pointer to the CPR3 controller -+ * @pdev: Platform device pointer for the CPR3 controller -+ * @start: start bit in TCSR register -+ * @end: end bit in TCSR register -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_read_tcsr_setting(struct cpr3_controller *ctrl, -+ struct platform_device *pdev, u8 start, u8 end) -+{ -+ struct resource *res; -+ void __iomem *tcsr_reg; -+ u32 val; -+ -+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, -+ "cpr_tcsr_reg"); -+ if (!res || !res->start) -+ return 0; -+ -+ tcsr_reg = ioremap(res->start, resource_size(res)); -+ if (!tcsr_reg) { -+ dev_err(&pdev->dev, "tcsr ioremap failed\n"); -+ return 0; -+ } -+ -+ val = readl_relaxed(tcsr_reg); -+ val &= GENMASK(end, start); -+ val >>= start; -+ -+ switch (val) { -+ case 1: -+ ctrl->cpr_global_setting = CPR_DISABLED; -+ break; -+ case 2: -+ ctrl->cpr_global_setting = CPR_OPEN_LOOP_EN; -+ break; -+ case 3: -+ ctrl->cpr_global_setting = CPR_CLOSED_LOOP_EN; -+ break; -+ default: -+ ctrl->cpr_global_setting = CPR_DEFAULT; -+ } -+ -+ iounmap(tcsr_reg); -+ -+ return 0; -+} -+ -+/** -+ * cpr3_read_fuse_param() - reads a CPR3 fuse parameter out of eFuses -+ * @fuse_base_addr: Virtual memory address of the eFuse base address -+ * @param: Null terminated array of fuse param segments to read -+ * from -+ * @param_value: Output with value read from the eFuses -+ * -+ * This function reads from each of the parameter segments listed in the param -+ * array and concatenates their values together. Reading stops when an element -+ * is reached which has all 0 struct values. The total number of bits specified -+ * for the fuse parameter across all segments must be less than or equal to 64. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_read_fuse_param(void __iomem *fuse_base_addr, -+ const struct cpr3_fuse_param *param, u64 *param_value) -+{ -+ u64 fuse_val, val; -+ int bits; -+ int bits_total = 0; -+ -+ *param_value = 0; -+ -+ while (param->row || param->bit_start || param->bit_end) { -+ if (param->bit_start > param->bit_end -+ || param->bit_end > MAX_FUSE_ROW_BIT) { -+ pr_err("Invalid fuse parameter segment: row=%u, start=%u, end=%u\n", -+ param->row, param->bit_start, param->bit_end); -+ return -EINVAL; -+ } -+ -+ bits = param->bit_end - param->bit_start + 1; -+ if (bits_total + bits > 64) { -+ pr_err("Invalid fuse parameter segments; total bits = %d\n", -+ bits_total + bits); -+ return -EINVAL; -+ } -+ -+ fuse_val = readq_relaxed(fuse_base_addr -+ + param->row * BYTES_PER_FUSE_ROW); -+ val = (fuse_val >> param->bit_start) & ((1ULL << bits) - 1); -+ *param_value |= val << bits_total; -+ bits_total += bits; -+ -+ param++; -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr3_convert_open_loop_voltage_fuse() - converts an open loop voltage fuse -+ * value into an absolute voltage with units of microvolts -+ * @ref_volt: Reference voltage in microvolts -+ * @step_volt: The step size in microvolts of the fuse LSB -+ * @fuse: Open loop voltage fuse value -+ * @fuse_len: The bit length of the fuse value -+ * -+ * The MSB of the fuse parameter corresponds to a sign bit. If it is set, then -+ * the lower bits correspond to the number of steps to go down from the -+ * reference voltage. If it is not set, then the lower bits correspond to the -+ * number of steps to go up from the reference voltage. -+ */ -+int cpr3_convert_open_loop_voltage_fuse(int ref_volt, int step_volt, u32 fuse, -+ int fuse_len) -+{ -+ int sign, steps; -+ -+ sign = (fuse & (1 << (fuse_len - 1))) ? -1 : 1; -+ steps = fuse & ((1 << (fuse_len - 1)) - 1); -+ -+ return ref_volt + sign * steps * step_volt; -+} -+ -+/** -+ * cpr3_interpolate() - performs linear interpolation -+ * @x1 Lower known x value -+ * @y1 Lower known y value -+ * @x2 Upper known x value -+ * @y2 Upper known y value -+ * @x Intermediate x value -+ * -+ * Returns y where (x, y) falls on the line between (x1, y1) and (x2, y2). -+ * It is required that x1 < x2, y1 <= y2, and x1 <= x <= x2. If these -+ * conditions are not met, then y2 will be returned. -+ */ -+u64 cpr3_interpolate(u64 x1, u64 y1, u64 x2, u64 y2, u64 x) -+{ -+ u64 temp; -+ -+ if (x1 >= x2 || y1 > y2 || x1 > x || x > x2) -+ return y2; -+ -+ temp = (x2 - x) * (y2 - y1); -+ do_div(temp, (u32)(x2 - x1)); -+ -+ return y2 - temp; -+} -+ -+/** -+ * cpr3_parse_array_property() - fill an array from a portion of the values -+ * specified for a device tree property -+ * @vreg: Pointer to the CPR3 regulator -+ * @prop_name: The name of the device tree property to read from -+ * @tuple_size: The number of elements in each tuple -+ * @out: Output data array which must be of size tuple_size -+ * -+ * cpr3_parse_common_corner_data() must be called for vreg before this function -+ * is called so that fuse combo and speed bin size elements are initialized. -+ * -+ * Three formats are supported for the device tree property: -+ * 1. Length == tuple_size -+ * (reading begins at index 0) -+ * 2. Length == tuple_size * vreg->fuse_combos_supported -+ * (reading begins at index tuple_size * vreg->fuse_combo) -+ * 3. Length == tuple_size * vreg->speed_bins_supported -+ * (reading begins at index tuple_size * vreg->speed_bin_fuse) -+ * -+ * All other property lengths are treated as errors. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_parse_array_property(struct cpr3_regulator *vreg, -+ const char *prop_name, int tuple_size, u32 *out) -+{ -+ struct device_node *node = vreg->of_node; -+ int len = 0; -+ int i, offset, rc; -+ -+ if (!of_find_property(node, prop_name, &len)) { -+ cpr3_err(vreg, "property %s is missing\n", prop_name); -+ return -EINVAL; -+ } -+ -+ if (len == tuple_size * sizeof(u32)) { -+ offset = 0; -+ } else if (len == tuple_size * vreg->fuse_combos_supported -+ * sizeof(u32)) { -+ offset = tuple_size * vreg->fuse_combo; -+ } else if (vreg->speed_bins_supported > 0 && -+ len == tuple_size * vreg->speed_bins_supported * sizeof(u32)) { -+ offset = tuple_size * vreg->speed_bin_fuse; -+ } else { -+ if (vreg->speed_bins_supported > 0) -+ cpr3_err(vreg, "property %s has invalid length=%d, should be %zu, %zu, or %zu\n", -+ prop_name, len, -+ tuple_size * sizeof(u32), -+ tuple_size * vreg->speed_bins_supported -+ * sizeof(u32), -+ tuple_size * vreg->fuse_combos_supported -+ * sizeof(u32)); -+ else -+ cpr3_err(vreg, "property %s has invalid length=%d, should be %zu or %zu\n", -+ prop_name, len, -+ tuple_size * sizeof(u32), -+ tuple_size * vreg->fuse_combos_supported -+ * sizeof(u32)); -+ return -EINVAL; -+ } -+ -+ for (i = 0; i < tuple_size; i++) { -+ rc = of_property_read_u32_index(node, prop_name, offset + i, -+ &out[i]); -+ if (rc) { -+ cpr3_err(vreg, "error reading property %s, rc=%d\n", -+ prop_name, rc); -+ return rc; -+ } -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr3_parse_corner_array_property() - fill a per-corner array from a portion -+ * of the values specified for a device tree property -+ * @vreg: Pointer to the CPR3 regulator -+ * @prop_name: The name of the device tree property to read from -+ * @tuple_size: The number of elements in each per-corner tuple -+ * @out: Output data array which must be of size: -+ * tuple_size * vreg->corner_count -+ * -+ * cpr3_parse_common_corner_data() must be called for vreg before this function -+ * is called so that fuse combo and speed bin size elements are initialized. -+ * -+ * Three formats are supported for the device tree property: -+ * 1. Length == tuple_size * vreg->corner_count -+ * (reading begins at index 0) -+ * 2. Length == tuple_size * vreg->fuse_combo_corner_sum -+ * (reading begins at index tuple_size * vreg->fuse_combo_offset) -+ * 3. Length == tuple_size * vreg->speed_bin_corner_sum -+ * (reading begins at index tuple_size * vreg->speed_bin_offset) -+ * -+ * All other property lengths are treated as errors. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_parse_corner_array_property(struct cpr3_regulator *vreg, -+ const char *prop_name, int tuple_size, u32 *out) -+{ -+ struct device_node *node = vreg->of_node; -+ int len = 0; -+ int i, offset, rc; -+ -+ if (!of_find_property(node, prop_name, &len)) { -+ cpr3_err(vreg, "property %s is missing\n", prop_name); -+ return -EINVAL; -+ } -+ -+ if (len == tuple_size * vreg->corner_count * sizeof(u32)) { -+ offset = 0; -+ } else if (len == tuple_size * vreg->fuse_combo_corner_sum -+ * sizeof(u32)) { -+ offset = tuple_size * vreg->fuse_combo_offset; -+ } else if (vreg->speed_bin_corner_sum > 0 && -+ len == tuple_size * vreg->speed_bin_corner_sum * sizeof(u32)) { -+ offset = tuple_size * vreg->speed_bin_offset; -+ } else { -+ if (vreg->speed_bin_corner_sum > 0) -+ cpr3_err(vreg, "property %s has invalid length=%d, should be %zu, %zu, or %zu\n", -+ prop_name, len, -+ tuple_size * vreg->corner_count * sizeof(u32), -+ tuple_size * vreg->speed_bin_corner_sum -+ * sizeof(u32), -+ tuple_size * vreg->fuse_combo_corner_sum -+ * sizeof(u32)); -+ else -+ cpr3_err(vreg, "property %s has invalid length=%d, should be %zu or %zu\n", -+ prop_name, len, -+ tuple_size * vreg->corner_count * sizeof(u32), -+ tuple_size * vreg->fuse_combo_corner_sum -+ * sizeof(u32)); -+ return -EINVAL; -+ } -+ -+ for (i = 0; i < tuple_size * vreg->corner_count; i++) { -+ rc = of_property_read_u32_index(node, prop_name, offset + i, -+ &out[i]); -+ if (rc) { -+ cpr3_err(vreg, "error reading property %s, rc=%d\n", -+ prop_name, rc); -+ return rc; -+ } -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr3_parse_corner_band_array_property() - fill a per-corner band array -+ * from a portion of the values specified for a device tree -+ * property -+ * @vreg: Pointer to the CPR3 regulator -+ * @prop_name: The name of the device tree property to read from -+ * @tuple_size: The number of elements in each per-corner band tuple -+ * @out: Output data array which must be of size: -+ * tuple_size * vreg->corner_band_count -+ * -+ * cpr3_parse_common_corner_data() must be called for vreg before this function -+ * is called so that fuse combo and speed bin size elements are initialized. -+ * In addition, corner band fuse combo and speed bin sum and offset elements -+ * must be initialized prior to executing this function. -+ * -+ * Three formats are supported for the device tree property: -+ * 1. Length == tuple_size * vreg->corner_band_count -+ * (reading begins at index 0) -+ * 2. Length == tuple_size * vreg->fuse_combo_corner_band_sum -+ * (reading begins at index tuple_size * -+ * vreg->fuse_combo_corner_band_offset) -+ * 3. Length == tuple_size * vreg->speed_bin_corner_band_sum -+ * (reading begins at index tuple_size * -+ * vreg->speed_bin_corner_band_offset) -+ * -+ * All other property lengths are treated as errors. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_parse_corner_band_array_property(struct cpr3_regulator *vreg, -+ const char *prop_name, int tuple_size, u32 *out) -+{ -+ struct device_node *node = vreg->of_node; -+ int len = 0; -+ int i, offset, rc; -+ -+ if (!of_find_property(node, prop_name, &len)) { -+ cpr3_err(vreg, "property %s is missing\n", prop_name); -+ return -EINVAL; -+ } -+ -+ if (len == tuple_size * vreg->corner_band_count * sizeof(u32)) { -+ offset = 0; -+ } else if (len == tuple_size * vreg->fuse_combo_corner_band_sum -+ * sizeof(u32)) { -+ offset = tuple_size * vreg->fuse_combo_corner_band_offset; -+ } else if (vreg->speed_bin_corner_band_sum > 0 && -+ len == tuple_size * vreg->speed_bin_corner_band_sum * -+ sizeof(u32)) { -+ offset = tuple_size * vreg->speed_bin_corner_band_offset; -+ } else { -+ if (vreg->speed_bin_corner_band_sum > 0) -+ cpr3_err(vreg, "property %s has invalid length=%d, should be %zu, %zu, or %zu\n", -+ prop_name, len, -+ tuple_size * vreg->corner_band_count * -+ sizeof(u32), -+ tuple_size * vreg->speed_bin_corner_band_sum -+ * sizeof(u32), -+ tuple_size * vreg->fuse_combo_corner_band_sum -+ * sizeof(u32)); -+ else -+ cpr3_err(vreg, "property %s has invalid length=%d, should be %zu or %zu\n", -+ prop_name, len, -+ tuple_size * vreg->corner_band_count * -+ sizeof(u32), -+ tuple_size * vreg->fuse_combo_corner_band_sum -+ * sizeof(u32)); -+ return -EINVAL; -+ } -+ -+ for (i = 0; i < tuple_size * vreg->corner_band_count; i++) { -+ rc = of_property_read_u32_index(node, prop_name, offset + i, -+ &out[i]); -+ if (rc) { -+ cpr3_err(vreg, "error reading property %s, rc=%d\n", -+ prop_name, rc); -+ return rc; -+ } -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr3_parse_common_corner_data() - parse common CPR3 properties relating to -+ * the corners supported by a CPR3 regulator from device tree -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * This function reads, validates, and utilizes the following device tree -+ * properties: qcom,cpr-fuse-corners, qcom,cpr-fuse-combos, qcom,cpr-speed-bins, -+ * qcom,cpr-speed-bin-corners, qcom,cpr-corners, qcom,cpr-voltage-ceiling, -+ * qcom,cpr-voltage-floor, qcom,corner-frequencies, -+ * and qcom,cpr-corner-fmax-map. -+ * -+ * It initializes these CPR3 regulator elements: corner, corner_count, -+ * fuse_combos_supported, fuse_corner_map, and speed_bins_supported. It -+ * initializes these elements for each corner: ceiling_volt, floor_volt, -+ * proc_freq, and cpr_fuse_corner. -+ * -+ * It requires that the following CPR3 regulator elements be initialized before -+ * being called: fuse_corner_count, fuse_combo, and speed_bin_fuse. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_parse_common_corner_data(struct cpr3_regulator *vreg) -+{ -+ struct device_node *node = vreg->of_node; -+ struct cpr3_controller *ctrl = vreg->thread->ctrl; -+ u32 max_fuse_combos, fuse_corners, aging_allowed = 0; -+ u32 max_speed_bins = 0; -+ u32 *combo_corners; -+ u32 *speed_bin_corners; -+ u32 *temp; -+ int i, j, rc; -+ -+ rc = of_property_read_u32(node, "qcom,cpr-fuse-corners", &fuse_corners); -+ if (rc) { -+ cpr3_err(vreg, "error reading property qcom,cpr-fuse-corners, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ if (vreg->fuse_corner_count != fuse_corners) { -+ cpr3_err(vreg, "device tree config supports %d fuse corners but the hardware has %d fuse corners\n", -+ fuse_corners, vreg->fuse_corner_count); -+ return -EINVAL; -+ } -+ -+ rc = of_property_read_u32(node, "qcom,cpr-fuse-combos", -+ &max_fuse_combos); -+ if (rc) { -+ cpr3_err(vreg, "error reading property qcom,cpr-fuse-combos, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ /* -+ * Sanity check against arbitrarily large value to avoid excessive -+ * memory allocation. -+ */ -+ if (max_fuse_combos > 100 || max_fuse_combos == 0) { -+ cpr3_err(vreg, "qcom,cpr-fuse-combos is invalid: %u\n", -+ max_fuse_combos); -+ return -EINVAL; -+ } -+ -+ if (vreg->fuse_combo >= max_fuse_combos) { -+ cpr3_err(vreg, "device tree config supports fuse combos 0-%u but the hardware has combo %d\n", -+ max_fuse_combos - 1, vreg->fuse_combo); -+ BUG_ON(1); -+ return -EINVAL; -+ } -+ -+ vreg->fuse_combos_supported = max_fuse_combos; -+ -+ of_property_read_u32(node, "qcom,cpr-speed-bins", &max_speed_bins); -+ -+ /* -+ * Sanity check against arbitrarily large value to avoid excessive -+ * memory allocation. -+ */ -+ if (max_speed_bins > 100) { -+ cpr3_err(vreg, "qcom,cpr-speed-bins is invalid: %u\n", -+ max_speed_bins); -+ return -EINVAL; -+ } -+ -+ if (max_speed_bins && vreg->speed_bin_fuse >= max_speed_bins) { -+ cpr3_err(vreg, "device tree config supports speed bins 0-%u but the hardware has speed bin %d\n", -+ max_speed_bins - 1, vreg->speed_bin_fuse); -+ BUG(); -+ return -EINVAL; -+ } -+ -+ vreg->speed_bins_supported = max_speed_bins; -+ -+ combo_corners = kcalloc(vreg->fuse_combos_supported, -+ sizeof(*combo_corners), GFP_KERNEL); -+ if (!combo_corners) -+ return -ENOMEM; -+ -+ rc = of_property_read_u32_array(node, "qcom,cpr-corners", combo_corners, -+ vreg->fuse_combos_supported); -+ if (rc == -EOVERFLOW) { -+ /* Single value case */ -+ rc = of_property_read_u32(node, "qcom,cpr-corners", -+ combo_corners); -+ for (i = 1; i < vreg->fuse_combos_supported; i++) -+ combo_corners[i] = combo_corners[0]; -+ } -+ if (rc) { -+ cpr3_err(vreg, "error reading property qcom,cpr-corners, rc=%d\n", -+ rc); -+ kfree(combo_corners); -+ return rc; -+ } -+ -+ vreg->fuse_combo_offset = 0; -+ vreg->fuse_combo_corner_sum = 0; -+ for (i = 0; i < vreg->fuse_combos_supported; i++) { -+ vreg->fuse_combo_corner_sum += combo_corners[i]; -+ if (i < vreg->fuse_combo) -+ vreg->fuse_combo_offset += combo_corners[i]; -+ } -+ -+ vreg->corner_count = combo_corners[vreg->fuse_combo]; -+ -+ kfree(combo_corners); -+ -+ vreg->speed_bin_offset = 0; -+ vreg->speed_bin_corner_sum = 0; -+ if (vreg->speed_bins_supported > 0) { -+ speed_bin_corners = kcalloc(vreg->speed_bins_supported, -+ sizeof(*speed_bin_corners), GFP_KERNEL); -+ if (!speed_bin_corners) -+ return -ENOMEM; -+ -+ rc = of_property_read_u32_array(node, -+ "qcom,cpr-speed-bin-corners", speed_bin_corners, -+ vreg->speed_bins_supported); -+ if (rc) { -+ cpr3_err(vreg, "error reading property qcom,cpr-speed-bin-corners, rc=%d\n", -+ rc); -+ kfree(speed_bin_corners); -+ return rc; -+ } -+ -+ for (i = 0; i < vreg->speed_bins_supported; i++) { -+ vreg->speed_bin_corner_sum += speed_bin_corners[i]; -+ if (i < vreg->speed_bin_fuse) -+ vreg->speed_bin_offset += speed_bin_corners[i]; -+ } -+ -+ if (speed_bin_corners[vreg->speed_bin_fuse] -+ != vreg->corner_count) { -+ cpr3_err(vreg, "qcom,cpr-corners and qcom,cpr-speed-bin-corners conflict on number of corners: %d vs %u\n", -+ vreg->corner_count, -+ speed_bin_corners[vreg->speed_bin_fuse]); -+ kfree(speed_bin_corners); -+ return -EINVAL; -+ } -+ -+ kfree(speed_bin_corners); -+ } -+ -+ vreg->corner = devm_kcalloc(ctrl->dev, vreg->corner_count, -+ sizeof(*vreg->corner), GFP_KERNEL); -+ temp = kcalloc(vreg->corner_count, sizeof(*temp), GFP_KERNEL); -+ if (!vreg->corner || !temp) -+ return -ENOMEM; -+ -+ rc = cpr3_parse_corner_array_property(vreg, "qcom,cpr-voltage-ceiling", -+ 1, temp); -+ if (rc) -+ goto free_temp; -+ for (i = 0; i < vreg->corner_count; i++) { -+ vreg->corner[i].ceiling_volt -+ = CPR3_ROUND(temp[i], ctrl->step_volt); -+ vreg->corner[i].abs_ceiling_volt = vreg->corner[i].ceiling_volt; -+ } -+ -+ rc = cpr3_parse_corner_array_property(vreg, "qcom,cpr-voltage-floor", -+ 1, temp); -+ if (rc) -+ goto free_temp; -+ for (i = 0; i < vreg->corner_count; i++) -+ vreg->corner[i].floor_volt -+ = CPR3_ROUND(temp[i], ctrl->step_volt); -+ -+ /* Validate ceiling and floor values */ -+ for (i = 0; i < vreg->corner_count; i++) { -+ if (vreg->corner[i].floor_volt -+ > vreg->corner[i].ceiling_volt) { -+ cpr3_err(vreg, "CPR floor[%d]=%d > ceiling[%d]=%d uV\n", -+ i, vreg->corner[i].floor_volt, -+ i, vreg->corner[i].ceiling_volt); -+ rc = -EINVAL; -+ goto free_temp; -+ } -+ } -+ -+ /* Load optional system-supply voltages */ -+ if (of_find_property(vreg->of_node, "qcom,system-voltage", NULL)) { -+ rc = cpr3_parse_corner_array_property(vreg, -+ "qcom,system-voltage", 1, temp); -+ if (rc) -+ goto free_temp; -+ for (i = 0; i < vreg->corner_count; i++) -+ vreg->corner[i].system_volt = temp[i]; -+ } -+ -+ rc = cpr3_parse_corner_array_property(vreg, "qcom,corner-frequencies", -+ 1, temp); -+ if (rc) -+ goto free_temp; -+ for (i = 0; i < vreg->corner_count; i++) -+ vreg->corner[i].proc_freq = temp[i]; -+ -+ /* Validate frequencies */ -+ for (i = 1; i < vreg->corner_count; i++) { -+ if (vreg->corner[i].proc_freq -+ < vreg->corner[i - 1].proc_freq) { -+ cpr3_err(vreg, "invalid frequency: freq[%d]=%u < freq[%d]=%u\n", -+ i, vreg->corner[i].proc_freq, i - 1, -+ vreg->corner[i - 1].proc_freq); -+ rc = -EINVAL; -+ goto free_temp; -+ } -+ } -+ -+ vreg->fuse_corner_map = devm_kcalloc(ctrl->dev, vreg->fuse_corner_count, -+ sizeof(*vreg->fuse_corner_map), GFP_KERNEL); -+ if (!vreg->fuse_corner_map) { -+ rc = -ENOMEM; -+ goto free_temp; -+ } -+ -+ rc = cpr3_parse_array_property(vreg, "qcom,cpr-corner-fmax-map", -+ vreg->fuse_corner_count, temp); -+ if (rc) -+ goto free_temp; -+ for (i = 0; i < vreg->fuse_corner_count; i++) { -+ vreg->fuse_corner_map[i] = temp[i] - CPR3_CORNER_OFFSET; -+ if (temp[i] < CPR3_CORNER_OFFSET -+ || temp[i] > vreg->corner_count + CPR3_CORNER_OFFSET) { -+ cpr3_err(vreg, "invalid corner value specified in qcom,cpr-corner-fmax-map: %u\n", -+ temp[i]); -+ rc = -EINVAL; -+ goto free_temp; -+ } else if (i > 0 && temp[i - 1] >= temp[i]) { -+ cpr3_err(vreg, "invalid corner %u less than or equal to previous corner %u\n", -+ temp[i], temp[i - 1]); -+ rc = -EINVAL; -+ goto free_temp; -+ } -+ } -+ if (temp[vreg->fuse_corner_count - 1] != vreg->corner_count) -+ cpr3_debug(vreg, "Note: highest Fmax corner %u in qcom,cpr-corner-fmax-map does not match highest supported corner %d\n", -+ temp[vreg->fuse_corner_count - 1], -+ vreg->corner_count); -+ -+ for (i = 0; i < vreg->corner_count; i++) { -+ for (j = 0; j < vreg->fuse_corner_count; j++) { -+ if (i + CPR3_CORNER_OFFSET <= temp[j]) { -+ vreg->corner[i].cpr_fuse_corner = j; -+ break; -+ } -+ } -+ if (j == vreg->fuse_corner_count) { -+ /* -+ * Handle the case where the highest fuse corner maps -+ * to a corner below the highest corner. -+ */ -+ vreg->corner[i].cpr_fuse_corner -+ = vreg->fuse_corner_count - 1; -+ } -+ } -+ -+ if (of_find_property(vreg->of_node, -+ "qcom,allow-aging-voltage-adjustment", NULL)) { -+ rc = cpr3_parse_array_property(vreg, -+ "qcom,allow-aging-voltage-adjustment", -+ 1, &aging_allowed); -+ if (rc) -+ goto free_temp; -+ -+ vreg->aging_allowed = aging_allowed; -+ } -+ -+ if (of_find_property(vreg->of_node, -+ "qcom,allow-aging-open-loop-voltage-adjustment", NULL)) { -+ rc = cpr3_parse_array_property(vreg, -+ "qcom,allow-aging-open-loop-voltage-adjustment", -+ 1, &aging_allowed); -+ if (rc) -+ goto free_temp; -+ -+ vreg->aging_allow_open_loop_adj = aging_allowed; -+ } -+ -+ if (vreg->aging_allowed) { -+ if (ctrl->aging_ref_volt <= 0) { -+ cpr3_err(ctrl, "qcom,cpr-aging-ref-voltage must be specified\n"); -+ rc = -EINVAL; -+ goto free_temp; -+ } -+ -+ rc = cpr3_parse_array_property(vreg, -+ "qcom,cpr-aging-max-voltage-adjustment", -+ 1, &vreg->aging_max_adjust_volt); -+ if (rc) -+ goto free_temp; -+ -+ rc = cpr3_parse_array_property(vreg, -+ "qcom,cpr-aging-ref-corner", 1, &vreg->aging_corner); -+ if (rc) { -+ goto free_temp; -+ } else if (vreg->aging_corner < CPR3_CORNER_OFFSET -+ || vreg->aging_corner > vreg->corner_count - 1 -+ + CPR3_CORNER_OFFSET) { -+ cpr3_err(vreg, "aging reference corner=%d not in range [%d, %d]\n", -+ vreg->aging_corner, CPR3_CORNER_OFFSET, -+ vreg->corner_count - 1 + CPR3_CORNER_OFFSET); -+ rc = -EINVAL; -+ goto free_temp; -+ } -+ vreg->aging_corner -= CPR3_CORNER_OFFSET; -+ -+ if (of_find_property(vreg->of_node, "qcom,cpr-aging-derate", -+ NULL)) { -+ rc = cpr3_parse_corner_array_property(vreg, -+ "qcom,cpr-aging-derate", 1, temp); -+ if (rc) -+ goto free_temp; -+ -+ for (i = 0; i < vreg->corner_count; i++) -+ vreg->corner[i].aging_derate = temp[i]; -+ } else { -+ for (i = 0; i < vreg->corner_count; i++) -+ vreg->corner[i].aging_derate -+ = CPR3_AGING_DERATE_UNITY; -+ } -+ } -+ -+free_temp: -+ kfree(temp); -+ return rc; -+} -+ -+/** -+ * cpr3_parse_thread_u32() - parse the specified property from the CPR3 thread's -+ * device tree node and verify that it is within the allowed limits -+ * @thread: Pointer to the CPR3 thread -+ * @propname: The name of the device tree property to read -+ * @out_value: The output pointer to fill with the value read -+ * @value_min: The minimum allowed property value -+ * @value_max: The maximum allowed property value -+ * -+ * This function prints a verbose error message if the property is missing or -+ * has a value which is not within the specified range. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_parse_thread_u32(struct cpr3_thread *thread, const char *propname, -+ u32 *out_value, u32 value_min, u32 value_max) -+{ -+ int rc; -+ -+ rc = of_property_read_u32(thread->of_node, propname, out_value); -+ if (rc) { -+ cpr3_err(thread->ctrl, "thread %u error reading property %s, rc=%d\n", -+ thread->thread_id, propname, rc); -+ return rc; -+ } -+ -+ if (*out_value < value_min || *out_value > value_max) { -+ cpr3_err(thread->ctrl, "thread %u %s=%u is invalid; allowed range: [%u, %u]\n", -+ thread->thread_id, propname, *out_value, value_min, -+ value_max); -+ return -EINVAL; -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr3_parse_ctrl_u32() - parse the specified property from the CPR3 -+ * controller's device tree node and verify that it is within the -+ * allowed limits -+ * @ctrl: Pointer to the CPR3 controller -+ * @propname: The name of the device tree property to read -+ * @out_value: The output pointer to fill with the value read -+ * @value_min: The minimum allowed property value -+ * @value_max: The maximum allowed property value -+ * -+ * This function prints a verbose error message if the property is missing or -+ * has a value which is not within the specified range. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_parse_ctrl_u32(struct cpr3_controller *ctrl, const char *propname, -+ u32 *out_value, u32 value_min, u32 value_max) -+{ -+ int rc; -+ -+ rc = of_property_read_u32(ctrl->dev->of_node, propname, out_value); -+ if (rc) { -+ cpr3_err(ctrl, "error reading property %s, rc=%d\n", -+ propname, rc); -+ return rc; -+ } -+ -+ if (*out_value < value_min || *out_value > value_max) { -+ cpr3_err(ctrl, "%s=%u is invalid; allowed range: [%u, %u]\n", -+ propname, *out_value, value_min, value_max); -+ return -EINVAL; -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr3_parse_common_thread_data() - parse common CPR3 thread properties from -+ * device tree -+ * @thread: Pointer to the CPR3 thread -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_parse_common_thread_data(struct cpr3_thread *thread) -+{ -+ int rc; -+ -+ rc = cpr3_parse_thread_u32(thread, "qcom,cpr-consecutive-up", -+ &thread->consecutive_up, CPR3_CONSECUTIVE_UP_DOWN_MIN, -+ CPR3_CONSECUTIVE_UP_DOWN_MAX); -+ if (rc) -+ return rc; -+ -+ rc = cpr3_parse_thread_u32(thread, "qcom,cpr-consecutive-down", -+ &thread->consecutive_down, CPR3_CONSECUTIVE_UP_DOWN_MIN, -+ CPR3_CONSECUTIVE_UP_DOWN_MAX); -+ if (rc) -+ return rc; -+ -+ rc = cpr3_parse_thread_u32(thread, "qcom,cpr-up-threshold", -+ &thread->up_threshold, CPR3_UP_DOWN_THRESHOLD_MIN, -+ CPR3_UP_DOWN_THRESHOLD_MAX); -+ if (rc) -+ return rc; -+ -+ rc = cpr3_parse_thread_u32(thread, "qcom,cpr-down-threshold", -+ &thread->down_threshold, CPR3_UP_DOWN_THRESHOLD_MIN, -+ CPR3_UP_DOWN_THRESHOLD_MAX); -+ if (rc) -+ return rc; -+ -+ return rc; -+} -+ -+/** -+ * cpr3_parse_irq_affinity() - parse CPR IRQ affinity information -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_parse_irq_affinity(struct cpr3_controller *ctrl) -+{ -+ struct device_node *cpu_node; -+ int i, cpu; -+ int len = 0; -+ -+ if (!of_find_property(ctrl->dev->of_node, "qcom,cpr-interrupt-affinity", -+ &len)) { -+ /* No IRQ affinity required */ -+ return 0; -+ } -+ -+ len /= sizeof(u32); -+ -+ for (i = 0; i < len; i++) { -+ cpu_node = of_parse_phandle(ctrl->dev->of_node, -+ "qcom,cpr-interrupt-affinity", i); -+ if (!cpu_node) { -+ cpr3_err(ctrl, "could not find CPU node %d\n", i); -+ return -EINVAL; -+ } -+ -+ for_each_possible_cpu(cpu) { -+ if (of_get_cpu_node(cpu, NULL) == cpu_node) { -+ cpumask_set_cpu(cpu, &ctrl->irq_affinity_mask); -+ break; -+ } -+ } -+ of_node_put(cpu_node); -+ } -+ -+ return 0; -+} -+ -+static int cpr3_panic_notifier_init(struct cpr3_controller *ctrl) -+{ -+ struct device_node *node = ctrl->dev->of_node; -+ struct cpr3_panic_regs_info *panic_regs_info; -+ struct cpr3_reg_info *regs; -+ int i, reg_count, len, rc = 0; -+ -+ if (!of_find_property(node, "qcom,cpr-panic-reg-addr-list", &len)) { -+ /* panic register address list not specified */ -+ return rc; -+ } -+ -+ reg_count = len / sizeof(u32); -+ if (!reg_count) { -+ cpr3_err(ctrl, "qcom,cpr-panic-reg-addr-list has invalid len = %d\n", -+ len); -+ return -EINVAL; -+ } -+ -+ if (!of_find_property(node, "qcom,cpr-panic-reg-name-list", NULL)) { -+ cpr3_err(ctrl, "property qcom,cpr-panic-reg-name-list not specified\n"); -+ return -EINVAL; -+ } -+ -+ len = of_property_count_strings(node, "qcom,cpr-panic-reg-name-list"); -+ if (reg_count != len) { -+ cpr3_err(ctrl, "qcom,cpr-panic-reg-name-list should have %d strings\n", -+ reg_count); -+ return -EINVAL; -+ } -+ -+ panic_regs_info = devm_kzalloc(ctrl->dev, sizeof(*panic_regs_info), -+ GFP_KERNEL); -+ if (!panic_regs_info) -+ return -ENOMEM; -+ -+ regs = devm_kcalloc(ctrl->dev, reg_count, sizeof(*regs), GFP_KERNEL); -+ if (!regs) -+ return -ENOMEM; -+ -+ for (i = 0; i < reg_count; i++) { -+ rc = of_property_read_string_index(node, -+ "qcom,cpr-panic-reg-name-list", i, -+ &(regs[i].name)); -+ if (rc) { -+ cpr3_err(ctrl, "error reading property qcom,cpr-panic-reg-name-list, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ rc = of_property_read_u32_index(node, -+ "qcom,cpr-panic-reg-addr-list", i, -+ &(regs[i].addr)); -+ if (rc) { -+ cpr3_err(ctrl, "error reading property qcom,cpr-panic-reg-addr-list, rc=%d\n", -+ rc); -+ return rc; -+ } -+ regs[i].virt_addr = devm_ioremap(ctrl->dev, regs[i].addr, 0x4); -+ if (!regs[i].virt_addr) { -+ pr_err("Unable to map panic register addr 0x%08x\n", -+ regs[i].addr); -+ return -EINVAL; -+ } -+ regs[i].value = 0xFFFFFFFF; -+ } -+ -+ panic_regs_info->reg_count = reg_count; -+ panic_regs_info->regs = regs; -+ ctrl->panic_regs_info = panic_regs_info; -+ -+ return rc; -+} -+ -+/** -+ * cpr3_parse_common_ctrl_data() - parse common CPR3 controller properties from -+ * device tree -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_parse_common_ctrl_data(struct cpr3_controller *ctrl) -+{ -+ int rc; -+ -+ rc = cpr3_parse_ctrl_u32(ctrl, "qcom,cpr-sensor-time", -+ &ctrl->sensor_time, 0, UINT_MAX); -+ if (rc) -+ return rc; -+ -+ rc = cpr3_parse_ctrl_u32(ctrl, "qcom,cpr-loop-time", -+ &ctrl->loop_time, 0, UINT_MAX); -+ if (rc) -+ return rc; -+ -+ rc = cpr3_parse_ctrl_u32(ctrl, "qcom,cpr-idle-cycles", -+ &ctrl->idle_clocks, CPR3_IDLE_CLOCKS_MIN, -+ CPR3_IDLE_CLOCKS_MAX); -+ if (rc) -+ return rc; -+ -+ rc = cpr3_parse_ctrl_u32(ctrl, "qcom,cpr-step-quot-init-min", -+ &ctrl->step_quot_init_min, CPR3_STEP_QUOT_MIN, -+ CPR3_STEP_QUOT_MAX); -+ if (rc) -+ return rc; -+ -+ rc = cpr3_parse_ctrl_u32(ctrl, "qcom,cpr-step-quot-init-max", -+ &ctrl->step_quot_init_max, CPR3_STEP_QUOT_MIN, -+ CPR3_STEP_QUOT_MAX); -+ if (rc) -+ return rc; -+ -+ rc = of_property_read_u32(ctrl->dev->of_node, "qcom,voltage-step", -+ &ctrl->step_volt); -+ if (rc) { -+ cpr3_err(ctrl, "error reading property qcom,voltage-step, rc=%d\n", -+ rc); -+ return rc; -+ } -+ if (ctrl->step_volt <= 0) { -+ cpr3_err(ctrl, "qcom,voltage-step=%d is invalid\n", -+ ctrl->step_volt); -+ return -EINVAL; -+ } -+ -+ rc = cpr3_parse_ctrl_u32(ctrl, "qcom,cpr-count-mode", -+ &ctrl->count_mode, CPR3_COUNT_MODE_ALL_AT_ONCE_MIN, -+ CPR3_COUNT_MODE_STAGGERED); -+ if (rc) -+ return rc; -+ -+ /* Count repeat is optional */ -+ ctrl->count_repeat = 0; -+ of_property_read_u32(ctrl->dev->of_node, "qcom,cpr-count-repeat", -+ &ctrl->count_repeat); -+ -+ ctrl->cpr_allowed_sw = -+ of_property_read_bool(ctrl->dev->of_node, "qcom,cpr-enable") || -+ ctrl->cpr_global_setting == CPR_CLOSED_LOOP_EN; -+ -+ rc = cpr3_parse_irq_affinity(ctrl); -+ if (rc) -+ return rc; -+ -+ /* Aging reference voltage is optional */ -+ ctrl->aging_ref_volt = 0; -+ of_property_read_u32(ctrl->dev->of_node, "qcom,cpr-aging-ref-voltage", -+ &ctrl->aging_ref_volt); -+ -+ /* Aging possible bitmask is optional */ -+ ctrl->aging_possible_mask = 0; -+ of_property_read_u32(ctrl->dev->of_node, -+ "qcom,cpr-aging-allowed-reg-mask", -+ &ctrl->aging_possible_mask); -+ -+ if (ctrl->aging_possible_mask) { -+ /* -+ * Aging possible register value required if bitmask is -+ * specified -+ */ -+ rc = cpr3_parse_ctrl_u32(ctrl, -+ "qcom,cpr-aging-allowed-reg-value", -+ &ctrl->aging_possible_val, 0, UINT_MAX); -+ if (rc) -+ return rc; -+ } -+ -+ if (of_find_property(ctrl->dev->of_node, "clock-names", NULL)) { -+ ctrl->core_clk = devm_clk_get(ctrl->dev, "core_clk"); -+ if (IS_ERR(ctrl->core_clk)) { -+ rc = PTR_ERR(ctrl->core_clk); -+ if (rc != -EPROBE_DEFER) -+ cpr3_err(ctrl, "unable request core clock, rc=%d\n", -+ rc); -+ return rc; -+ } -+ } -+ -+ rc = cpr3_panic_notifier_init(ctrl); -+ if (rc) -+ return rc; -+ -+ if (of_find_property(ctrl->dev->of_node, "vdd-supply", NULL)) { -+ ctrl->vdd_regulator = devm_regulator_get(ctrl->dev, "vdd"); -+ if (IS_ERR(ctrl->vdd_regulator)) { -+ rc = PTR_ERR(ctrl->vdd_regulator); -+ if (rc != -EPROBE_DEFER) -+ cpr3_err(ctrl, "unable to request vdd regulator, rc=%d\n", -+ rc); -+ return rc; -+ } -+ } else { -+ cpr3_err(ctrl, "vdd supply is not defined\n"); -+ return -ENODEV; -+ } -+ -+ ctrl->system_regulator = devm_regulator_get_optional(ctrl->dev, -+ "system"); -+ if (IS_ERR(ctrl->system_regulator)) { -+ rc = PTR_ERR(ctrl->system_regulator); -+ if (rc != -EPROBE_DEFER) { -+ rc = 0; -+ ctrl->system_regulator = NULL; -+ } else { -+ return rc; -+ } -+ } -+ -+ ctrl->mem_acc_regulator = devm_regulator_get_optional(ctrl->dev, -+ "mem-acc"); -+ if (IS_ERR(ctrl->mem_acc_regulator)) { -+ rc = PTR_ERR(ctrl->mem_acc_regulator); -+ if (rc != -EPROBE_DEFER) { -+ rc = 0; -+ ctrl->mem_acc_regulator = NULL; -+ } else { -+ return rc; -+ } -+ } -+ -+ return rc; -+} -+ -+/** -+ * cpr3_parse_open_loop_common_ctrl_data() - parse common open loop CPR3 -+ * controller properties from device tree -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_parse_open_loop_common_ctrl_data(struct cpr3_controller *ctrl) -+{ -+ int rc; -+ -+ rc = of_property_read_u32(ctrl->dev->of_node, "qcom,voltage-step", -+ &ctrl->step_volt); -+ if (rc) { -+ cpr3_err(ctrl, "error reading property qcom,voltage-step, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ if (ctrl->step_volt <= 0) { -+ cpr3_err(ctrl, "qcom,voltage-step=%d is invalid\n", -+ ctrl->step_volt); -+ return -EINVAL; -+ } -+ -+ if (of_find_property(ctrl->dev->of_node, "vdd-supply", NULL)) { -+ ctrl->vdd_regulator = devm_regulator_get(ctrl->dev, "vdd"); -+ if (IS_ERR(ctrl->vdd_regulator)) { -+ rc = PTR_ERR(ctrl->vdd_regulator); -+ if (rc != -EPROBE_DEFER) -+ cpr3_err(ctrl, "unable to request vdd regulator, rc=%d\n", -+ rc); -+ return rc; -+ } -+ } else { -+ cpr3_err(ctrl, "vdd supply is not defined\n"); -+ return -ENODEV; -+ } -+ -+ ctrl->system_regulator = devm_regulator_get_optional(ctrl->dev, -+ "system"); -+ if (IS_ERR(ctrl->system_regulator)) { -+ rc = PTR_ERR(ctrl->system_regulator); -+ if (rc != -EPROBE_DEFER) { -+ rc = 0; -+ ctrl->system_regulator = NULL; -+ } else { -+ return rc; -+ } -+ } else { -+ rc = regulator_enable(ctrl->system_regulator); -+ } -+ -+ ctrl->mem_acc_regulator = devm_regulator_get_optional(ctrl->dev, -+ "mem-acc"); -+ if (IS_ERR(ctrl->mem_acc_regulator)) { -+ rc = PTR_ERR(ctrl->mem_acc_regulator); -+ if (rc != -EPROBE_DEFER) { -+ rc = 0; -+ ctrl->mem_acc_regulator = NULL; -+ } else { -+ return rc; -+ } -+ } -+ -+ return rc; -+} -+ -+/** -+ * cpr3_limit_open_loop_voltages() - modify the open-loop voltage of each corner -+ * so that it fits within the floor to ceiling -+ * voltage range of the corner -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * This function clips the open-loop voltage for each corner so that it is -+ * limited to the floor to ceiling range. It also rounds each open-loop voltage -+ * so that it corresponds to a set point available to the underlying regulator. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_limit_open_loop_voltages(struct cpr3_regulator *vreg) -+{ -+ int i, volt; -+ -+ cpr3_debug(vreg, "open-loop voltages after trimming and rounding:\n"); -+ for (i = 0; i < vreg->corner_count; i++) { -+ volt = CPR3_ROUND(vreg->corner[i].open_loop_volt, -+ vreg->thread->ctrl->step_volt); -+ if (volt < vreg->corner[i].floor_volt) -+ volt = vreg->corner[i].floor_volt; -+ else if (volt > vreg->corner[i].ceiling_volt) -+ volt = vreg->corner[i].ceiling_volt; -+ vreg->corner[i].open_loop_volt = volt; -+ cpr3_debug(vreg, "corner[%2d]: open-loop=%d uV\n", i, volt); -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr3_open_loop_voltage_as_ceiling() - configures the ceiling voltage for each -+ * corner to equal the open-loop voltage if the relevant device -+ * tree property is found for the CPR3 regulator -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * This function assumes that the the open-loop voltage for each corner has -+ * already been rounded to the nearest allowed set point and that it falls -+ * within the floor to ceiling range. -+ * -+ * Return: none -+ */ -+void cpr3_open_loop_voltage_as_ceiling(struct cpr3_regulator *vreg) -+{ -+ int i; -+ -+ if (!of_property_read_bool(vreg->of_node, -+ "qcom,cpr-scaled-open-loop-voltage-as-ceiling")) -+ return; -+ -+ for (i = 0; i < vreg->corner_count; i++) -+ vreg->corner[i].ceiling_volt -+ = vreg->corner[i].open_loop_volt; -+} -+ -+/** -+ * cpr3_limit_floor_voltages() - raise the floor voltage of each corner so that -+ * the optional maximum floor to ceiling voltage range specified in -+ * device tree is satisfied -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * This function also ensures that the open-loop voltage for each corner falls -+ * within the final floor to ceiling voltage range and that floor voltages -+ * increase monotonically. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_limit_floor_voltages(struct cpr3_regulator *vreg) -+{ -+ char *prop = "qcom,cpr-floor-to-ceiling-max-range"; -+ int i, floor_new; -+ u32 *floor_range; -+ int rc = 0; -+ -+ if (!of_find_property(vreg->of_node, prop, NULL)) -+ goto enforce_monotonicity; -+ -+ floor_range = kcalloc(vreg->corner_count, sizeof(*floor_range), -+ GFP_KERNEL); -+ if (!floor_range) -+ return -ENOMEM; -+ -+ rc = cpr3_parse_corner_array_property(vreg, prop, 1, floor_range); -+ if (rc) -+ goto free_floor_adjust; -+ -+ for (i = 0; i < vreg->corner_count; i++) { -+ if ((s32)floor_range[i] >= 0) { -+ floor_new = CPR3_ROUND(vreg->corner[i].ceiling_volt -+ - floor_range[i], -+ vreg->thread->ctrl->step_volt); -+ -+ vreg->corner[i].floor_volt = max(floor_new, -+ vreg->corner[i].floor_volt); -+ if (vreg->corner[i].open_loop_volt -+ < vreg->corner[i].floor_volt) -+ vreg->corner[i].open_loop_volt -+ = vreg->corner[i].floor_volt; -+ } -+ } -+ -+free_floor_adjust: -+ kfree(floor_range); -+ -+enforce_monotonicity: -+ /* Ensure that floor voltages increase monotonically. */ -+ for (i = 1; i < vreg->corner_count; i++) { -+ if (vreg->corner[i].floor_volt -+ < vreg->corner[i - 1].floor_volt) { -+ cpr3_debug(vreg, "corner %d floor voltage=%d uV < corner %d voltage=%d uV; overriding: corner %d voltage=%d\n", -+ i, vreg->corner[i].floor_volt, -+ i - 1, vreg->corner[i - 1].floor_volt, -+ i, vreg->corner[i - 1].floor_volt); -+ vreg->corner[i].floor_volt -+ = vreg->corner[i - 1].floor_volt; -+ -+ if (vreg->corner[i].open_loop_volt -+ < vreg->corner[i].floor_volt) -+ vreg->corner[i].open_loop_volt -+ = vreg->corner[i].floor_volt; -+ if (vreg->corner[i].ceiling_volt -+ < vreg->corner[i].floor_volt) -+ vreg->corner[i].ceiling_volt -+ = vreg->corner[i].floor_volt; -+ } -+ } -+ -+ return rc; -+} -+ -+/** -+ * cpr3_print_quots() - print CPR target quotients into the kernel log for -+ * debugging purposes -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * Return: none -+ */ -+void cpr3_print_quots(struct cpr3_regulator *vreg) -+{ -+ int i, j, pos; -+ size_t buflen; -+ char *buf; -+ -+ buflen = sizeof(*buf) * CPR3_RO_COUNT * (MAX_CHARS_PER_INT + 2); -+ buf = kzalloc(buflen, GFP_KERNEL); -+ if (!buf) -+ return; -+ -+ for (i = 0; i < vreg->corner_count; i++) { -+ for (j = 0, pos = 0; j < CPR3_RO_COUNT; j++) -+ pos += scnprintf(buf + pos, buflen - pos, " %u", -+ vreg->corner[i].target_quot[j]); -+ cpr3_debug(vreg, "target quots[%2d]:%s\n", i, buf); -+ } -+ -+ kfree(buf); -+} -+ -+/** -+ * cpr3_determine_part_type() - determine the part type (SS/TT/FF). -+ * -+ * qcom,cpr-part-types prop tells the number of part types for which correction -+ * voltages are different. Another prop qcom,cpr-parts-voltage will contain the -+ * open loop fuse voltage which will be compared with this part voltage -+ * and accordingly part type will de determined. -+ * -+ * if qcom,cpr-part-types has value n, then qcom,cpr-parts-voltage will be -+ * array of n - 1 elements which will contain the voltage in increasing order. -+ * This function compares the fused volatge with all these voltage and returns -+ * the first index for which the fused volatge is greater. -+ * -+ * @vreg: Pointer to the CPR3 regulator -+ * @fuse_volt: fused open loop voltage which will be compared with -+ * qcom,cpr-parts-voltage array -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_determine_part_type(struct cpr3_regulator *vreg, int fuse_volt) -+{ -+ int i, rc, len; -+ u32 volt; -+ int soc_version_major; -+ char prop_name[100]; -+ const char prop_name_def[] = "qcom,cpr-parts-voltage"; -+ const char prop_name_v2[] = "qcom,cpr-parts-voltage-v2"; -+ -+ soc_version_major = read_ipq_soc_version_major(); -+ BUG_ON(soc_version_major <= 0); -+ -+ if (of_property_read_u32(vreg->of_node, "qcom,cpr-part-types", -+ &vreg->part_type_supported)) -+ return 0; -+ -+ if (soc_version_major > 1) -+ strlcpy(prop_name, prop_name_v2, sizeof(prop_name_v2)); -+ else -+ strlcpy(prop_name, prop_name_def, sizeof(prop_name_def)); -+ -+ if (!of_find_property(vreg->of_node, prop_name, &len)) { -+ cpr3_err(vreg, "property %s is missing\n", prop_name); -+ return -EINVAL; -+ } -+ -+ if (len != (vreg->part_type_supported - 1) * sizeof(u32)) { -+ cpr3_err(vreg, "wrong len in qcom,cpr-parts-voltage\n"); -+ return -EINVAL; -+ } -+ -+ for (i = 0; i < vreg->part_type_supported - 1; i++) { -+ rc = of_property_read_u32_index(vreg->of_node, -+ prop_name, i, &volt); -+ if (rc) { -+ cpr3_err(vreg, "error reading property %s, rc=%d\n", -+ prop_name, rc); -+ return rc; -+ } -+ -+ if (fuse_volt < volt) -+ break; -+ } -+ -+ vreg->part_type = i; -+ return 0; -+} -+ -+int cpr3_determine_temp_base_open_loop_correction(struct cpr3_regulator *vreg, -+ int *fuse_volt) -+{ -+ int i, rc, prev_volt; -+ int *volt_adjust; -+ char prop_str[75]; -+ int soc_version_major = read_ipq_soc_version_major(); -+ -+ BUG_ON(soc_version_major <= 0); -+ -+ if (vreg->part_type_supported) { -+ if (soc_version_major > 1) -+ snprintf(prop_str, sizeof(prop_str), -+ "qcom,cpr-cold-temp-voltage-adjustment-v2-%d", -+ vreg->part_type); -+ else -+ snprintf(prop_str, sizeof(prop_str), -+ "qcom,cpr-cold-temp-voltage-adjustment-%d", -+ vreg->part_type); -+ } else { -+ strlcpy(prop_str, "qcom,cpr-cold-temp-voltage-adjustment", -+ sizeof(prop_str)); -+ } -+ -+ if (!of_find_property(vreg->of_node, prop_str, NULL)) { -+ /* No adjustment required. */ -+ cpr3_info(vreg, "No cold temperature adjustment required.\n"); -+ return 0; -+ } -+ -+ volt_adjust = kcalloc(vreg->fuse_corner_count, sizeof(*volt_adjust), -+ GFP_KERNEL); -+ if (!volt_adjust) -+ return -ENOMEM; -+ -+ rc = cpr3_parse_array_property(vreg, prop_str, -+ vreg->fuse_corner_count, volt_adjust); -+ if (rc) { -+ cpr3_err(vreg, "could not load cold temp voltage adjustments, rc=%d\n", -+ rc); -+ goto done; -+ } -+ -+ for (i = 0; i < vreg->fuse_corner_count; i++) { -+ if (volt_adjust[i]) { -+ prev_volt = fuse_volt[i]; -+ fuse_volt[i] += volt_adjust[i]; -+ cpr3_debug(vreg, -+ "adjusted fuse corner %d open-loop voltage: %d -> %d uV\n", -+ i, prev_volt, fuse_volt[i]); -+ } -+ } -+ -+done: -+ kfree(volt_adjust); -+ return rc; -+} -+ -+/** -+ * cpr3_can_adjust_cold_temp() - Is cold temperature adjustment available -+ * -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * This function checks the cold temperature threshold is available -+ * -+ * Return: true on cold temperature threshold is available, else false -+ */ -+bool cpr3_can_adjust_cold_temp(struct cpr3_regulator *vreg) -+{ -+ char prop_str[75]; -+ int soc_version_major = read_ipq_soc_version_major(); -+ -+ BUG_ON(soc_version_major <= 0); -+ -+ if (soc_version_major > 1) -+ strlcpy(prop_str, "qcom,cpr-cold-temp-threshold-v2", -+ sizeof(prop_str)); -+ else -+ strlcpy(prop_str, "qcom,cpr-cold-temp-threshold", -+ sizeof(prop_str)); -+ -+ if (!of_find_property(vreg->of_node, prop_str, NULL)) { -+ /* No adjustment required. */ -+ return false; -+ } else -+ return true; -+} -+ -+/** -+ * cpr3_get_cold_temp_threshold() - get cold temperature threshold -+ * -+ * @vreg: Pointer to the CPR3 regulator -+ * @cold_temp: cold temperature read. -+ * -+ * This function reads the cold temperature threshold below which -+ * cold temperature adjustment margins will be applied. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_get_cold_temp_threshold(struct cpr3_regulator *vreg, int *cold_temp) -+{ -+ int rc; -+ u32 temp; -+ char req_prop_str[75], prop_str[75]; -+ int soc_version_major = read_ipq_soc_version_major(); -+ -+ BUG_ON(soc_version_major <= 0); -+ -+ if (vreg->part_type_supported) { -+ if (soc_version_major > 1) -+ snprintf(req_prop_str, sizeof(req_prop_str), -+ "qcom,cpr-cold-temp-voltage-adjustment-v2-%d", -+ vreg->part_type); -+ else -+ snprintf(req_prop_str, sizeof(req_prop_str), -+ "qcom,cpr-cold-temp-voltage-adjustment-%d", -+ vreg->part_type); -+ } else { -+ strlcpy(req_prop_str, "qcom,cpr-cold-temp-voltage-adjustment", -+ sizeof(req_prop_str)); -+ } -+ -+ if (soc_version_major > 1) -+ strlcpy(prop_str, "qcom,cpr-cold-temp-threshold-v2", -+ sizeof(prop_str)); -+ else -+ strlcpy(prop_str, "qcom,cpr-cold-temp-threshold", -+ sizeof(prop_str)); -+ -+ if (!of_find_property(vreg->of_node, req_prop_str, NULL)) { -+ /* No adjustment required. */ -+ cpr3_info(vreg, "Cold temperature adjustment not required.\n"); -+ return 0; -+ } -+ -+ if (!of_find_property(vreg->of_node, prop_str, NULL)) { -+ /* No adjustment required. */ -+ cpr3_err(vreg, "Missing %s required for %s\n", -+ prop_str, req_prop_str); -+ return -EINVAL; -+ } -+ -+ rc = of_property_read_u32(vreg->of_node, prop_str, &temp); -+ if (rc) { -+ cpr3_err(vreg, "error reading property %s, rc=%d\n", -+ prop_str, rc); -+ return rc; -+ } -+ -+ *cold_temp = temp; -+ return 0; -+} -+ -+/** -+ * cpr3_adjust_fused_open_loop_voltages() - adjust the fused open-loop voltages -+ * for each fuse corner according to device tree values -+ * @vreg: Pointer to the CPR3 regulator -+ * @fuse_volt: Pointer to an array of the fused open-loop voltage -+ * values -+ * -+ * Voltage values in fuse_volt are modified in place. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_adjust_fused_open_loop_voltages(struct cpr3_regulator *vreg, -+ int *fuse_volt) -+{ -+ int i, rc, prev_volt; -+ int *volt_adjust; -+ char prop_str[75]; -+ int soc_version_major = read_ipq_soc_version_major(); -+ -+ BUG_ON(soc_version_major <= 0); -+ -+ if (vreg->part_type_supported) { -+ if (soc_version_major > 1) -+ snprintf(prop_str, sizeof(prop_str), -+ "qcom,cpr-open-loop-voltage-fuse-adjustment-v2-%d", -+ vreg->part_type); -+ else -+ snprintf(prop_str, sizeof(prop_str), -+ "qcom,cpr-open-loop-voltage-fuse-adjustment-%d", -+ vreg->part_type); -+ } else { -+ strlcpy(prop_str, "qcom,cpr-open-loop-voltage-fuse-adjustment", -+ sizeof(prop_str)); -+ } -+ -+ if (!of_find_property(vreg->of_node, prop_str, NULL)) { -+ /* No adjustment required. */ -+ return 0; -+ } -+ -+ volt_adjust = kcalloc(vreg->fuse_corner_count, sizeof(*volt_adjust), -+ GFP_KERNEL); -+ if (!volt_adjust) -+ return -ENOMEM; -+ -+ rc = cpr3_parse_array_property(vreg, -+ prop_str, vreg->fuse_corner_count, volt_adjust); -+ if (rc) { -+ cpr3_err(vreg, "could not load open-loop fused voltage adjustments, rc=%d\n", -+ rc); -+ goto done; -+ } -+ -+ for (i = 0; i < vreg->fuse_corner_count; i++) { -+ if (volt_adjust[i]) { -+ prev_volt = fuse_volt[i]; -+ fuse_volt[i] += volt_adjust[i]; -+ cpr3_debug(vreg, "adjusted fuse corner %d open-loop voltage: %d --> %d uV\n", -+ i, prev_volt, fuse_volt[i]); -+ } -+ } -+ -+done: -+ kfree(volt_adjust); -+ return rc; -+} -+ -+/** -+ * cpr3_adjust_open_loop_voltages() - adjust the open-loop voltages for each -+ * corner according to device tree values -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_adjust_open_loop_voltages(struct cpr3_regulator *vreg) -+{ -+ int i, rc, prev_volt, min_volt; -+ int *volt_adjust, *volt_diff; -+ -+ if (!of_find_property(vreg->of_node, -+ "qcom,cpr-open-loop-voltage-adjustment", NULL)) { -+ /* No adjustment required. */ -+ return 0; -+ } -+ -+ volt_adjust = kcalloc(vreg->corner_count, sizeof(*volt_adjust), -+ GFP_KERNEL); -+ volt_diff = kcalloc(vreg->corner_count, sizeof(*volt_diff), GFP_KERNEL); -+ if (!volt_adjust || !volt_diff) { -+ rc = -ENOMEM; -+ goto done; -+ } -+ -+ rc = cpr3_parse_corner_array_property(vreg, -+ "qcom,cpr-open-loop-voltage-adjustment", 1, volt_adjust); -+ if (rc) { -+ cpr3_err(vreg, "could not load open-loop voltage adjustments, rc=%d\n", -+ rc); -+ goto done; -+ } -+ -+ for (i = 0; i < vreg->corner_count; i++) { -+ if (volt_adjust[i]) { -+ prev_volt = vreg->corner[i].open_loop_volt; -+ vreg->corner[i].open_loop_volt += volt_adjust[i]; -+ cpr3_debug(vreg, "adjusted corner %d open-loop voltage: %d --> %d uV\n", -+ i, prev_volt, vreg->corner[i].open_loop_volt); -+ } -+ } -+ -+ if (of_find_property(vreg->of_node, -+ "qcom,cpr-open-loop-voltage-min-diff", NULL)) { -+ rc = cpr3_parse_corner_array_property(vreg, -+ "qcom,cpr-open-loop-voltage-min-diff", 1, volt_diff); -+ if (rc) { -+ cpr3_err(vreg, "could not load minimum open-loop voltage differences, rc=%d\n", -+ rc); -+ goto done; -+ } -+ } -+ -+ /* -+ * Ensure that open-loop voltages increase monotonically with respect -+ * to configurable minimum allowed differences. -+ */ -+ for (i = 1; i < vreg->corner_count; i++) { -+ min_volt = vreg->corner[i - 1].open_loop_volt + volt_diff[i]; -+ if (vreg->corner[i].open_loop_volt < min_volt) { -+ cpr3_debug(vreg, "adjusted corner %d open-loop voltage=%d uV < corner %d voltage=%d uV + min diff=%d uV; overriding: corner %d voltage=%d\n", -+ i, vreg->corner[i].open_loop_volt, -+ i - 1, vreg->corner[i - 1].open_loop_volt, -+ volt_diff[i], i, min_volt); -+ vreg->corner[i].open_loop_volt = min_volt; -+ } -+ } -+ -+done: -+ kfree(volt_diff); -+ kfree(volt_adjust); -+ return rc; -+} -+ -+/** -+ * cpr3_quot_adjustment() - returns the quotient adjustment value resulting from -+ * the specified voltage adjustment and RO scaling factor -+ * @ro_scale: The CPR ring oscillator (RO) scaling factor with units -+ * of QUOT/V -+ * @volt_adjust: The amount to adjust the voltage by in units of -+ * microvolts. This value may be positive or negative. -+ */ -+int cpr3_quot_adjustment(int ro_scale, int volt_adjust) -+{ -+ unsigned long long temp; -+ int quot_adjust; -+ int sign = 1; -+ -+ if (ro_scale < 0) { -+ sign = -sign; -+ ro_scale = -ro_scale; -+ } -+ -+ if (volt_adjust < 0) { -+ sign = -sign; -+ volt_adjust = -volt_adjust; -+ } -+ -+ temp = (unsigned long long)ro_scale * (unsigned long long)volt_adjust; -+ do_div(temp, 1000000); -+ -+ quot_adjust = temp; -+ quot_adjust *= sign; -+ -+ return quot_adjust; -+} -+ -+/** -+ * cpr3_voltage_adjustment() - returns the voltage adjustment value resulting -+ * from the specified quotient adjustment and RO scaling factor -+ * @ro_scale: The CPR ring oscillator (RO) scaling factor with units -+ * of QUOT/V -+ * @quot_adjust: The amount to adjust the quotient by in units of -+ * QUOT. This value may be positive or negative. -+ */ -+int cpr3_voltage_adjustment(int ro_scale, int quot_adjust) -+{ -+ unsigned long long temp; -+ int volt_adjust; -+ int sign = 1; -+ -+ if (ro_scale < 0) { -+ sign = -sign; -+ ro_scale = -ro_scale; -+ } -+ -+ if (quot_adjust < 0) { -+ sign = -sign; -+ quot_adjust = -quot_adjust; -+ } -+ -+ if (ro_scale == 0) -+ return 0; -+ -+ temp = (unsigned long long)quot_adjust * 1000000; -+ do_div(temp, ro_scale); -+ -+ volt_adjust = temp; -+ volt_adjust *= sign; -+ -+ return volt_adjust; -+} -+ -+/** -+ * cpr3_parse_closed_loop_voltage_adjustments() - load per-fuse-corner and -+ * per-corner closed-loop adjustment values from device tree -+ * @vreg: Pointer to the CPR3 regulator -+ * @ro_sel: Array of ring oscillator values selected for each -+ * fuse corner -+ * @volt_adjust: Pointer to array which will be filled with the -+ * per-corner closed-loop adjustment voltages -+ * @volt_adjust_fuse: Pointer to array which will be filled with the -+ * per-fuse-corner closed-loop adjustment voltages -+ * @ro_scale: Pointer to array which will be filled with the -+ * per-fuse-corner RO scaling factor values with units of -+ * QUOT/V -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_parse_closed_loop_voltage_adjustments( -+ struct cpr3_regulator *vreg, u64 *ro_sel, -+ int *volt_adjust, int *volt_adjust_fuse, int *ro_scale) -+{ -+ int i, rc; -+ u32 *ro_all_scale; -+ -+ char volt_adj[] = "qcom,cpr-closed-loop-voltage-adjustment"; -+ char volt_fuse_adj[] = "qcom,cpr-closed-loop-voltage-fuse-adjustment"; -+ char ro_scaling[] = "qcom,cpr-ro-scaling-factor"; -+ -+ if (!of_find_property(vreg->of_node, volt_adj, NULL) -+ && !of_find_property(vreg->of_node, volt_fuse_adj, NULL) -+ && !vreg->aging_allowed) { -+ /* No adjustment required. */ -+ return 0; -+ } else if (!of_find_property(vreg->of_node, ro_scaling, NULL)) { -+ cpr3_err(vreg, "Missing %s required for closed-loop voltage adjustment.\n", -+ ro_scaling); -+ return -EINVAL; -+ } -+ -+ ro_all_scale = kcalloc(vreg->fuse_corner_count * CPR3_RO_COUNT, -+ sizeof(*ro_all_scale), GFP_KERNEL); -+ if (!ro_all_scale) -+ return -ENOMEM; -+ -+ rc = cpr3_parse_array_property(vreg, ro_scaling, -+ vreg->fuse_corner_count * CPR3_RO_COUNT, ro_all_scale); -+ if (rc) { -+ cpr3_err(vreg, "could not load RO scaling factors, rc=%d\n", -+ rc); -+ goto done; -+ } -+ -+ for (i = 0; i < vreg->fuse_corner_count; i++) -+ ro_scale[i] = ro_all_scale[i * CPR3_RO_COUNT + ro_sel[i]]; -+ -+ for (i = 0; i < vreg->corner_count; i++) -+ memcpy(vreg->corner[i].ro_scale, -+ &ro_all_scale[vreg->corner[i].cpr_fuse_corner * CPR3_RO_COUNT], -+ sizeof(*ro_all_scale) * CPR3_RO_COUNT); -+ -+ if (of_find_property(vreg->of_node, volt_fuse_adj, NULL)) { -+ rc = cpr3_parse_array_property(vreg, volt_fuse_adj, -+ vreg->fuse_corner_count, volt_adjust_fuse); -+ if (rc) { -+ cpr3_err(vreg, "could not load closed-loop fused voltage adjustments, rc=%d\n", -+ rc); -+ goto done; -+ } -+ } -+ -+ if (of_find_property(vreg->of_node, volt_adj, NULL)) { -+ rc = cpr3_parse_corner_array_property(vreg, volt_adj, -+ 1, volt_adjust); -+ if (rc) { -+ cpr3_err(vreg, "could not load closed-loop voltage adjustments, rc=%d\n", -+ rc); -+ goto done; -+ } -+ } -+ -+done: -+ kfree(ro_all_scale); -+ return rc; -+} -+ -+/** -+ * cpr3_apm_init() - initialize APM data for a CPR3 controller -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * This function loads memory array power mux (APM) data from device tree -+ * if it is present and requests a handle to the appropriate APM controller -+ * device. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_apm_init(struct cpr3_controller *ctrl) -+{ -+ struct device_node *node = ctrl->dev->of_node; -+ int rc; -+ -+ if (!of_find_property(node, "qcom,apm-ctrl", NULL)) { -+ /* No APM used */ -+ return 0; -+ } -+ -+ ctrl->apm = msm_apm_ctrl_dev_get(ctrl->dev); -+ if (IS_ERR(ctrl->apm)) { -+ rc = PTR_ERR(ctrl->apm); -+ if (rc != -EPROBE_DEFER) -+ cpr3_err(ctrl, "APM get failed, rc=%d\n", rc); -+ return rc; -+ } -+ -+ rc = of_property_read_u32(node, "qcom,apm-threshold-voltage", -+ &ctrl->apm_threshold_volt); -+ if (rc) { -+ cpr3_err(ctrl, "error reading qcom,apm-threshold-voltage, rc=%d\n", -+ rc); -+ return rc; -+ } -+ ctrl->apm_threshold_volt -+ = CPR3_ROUND(ctrl->apm_threshold_volt, ctrl->step_volt); -+ -+ /* No error check since this is an optional property. */ -+ of_property_read_u32(node, "qcom,apm-hysteresis-voltage", -+ &ctrl->apm_adj_volt); -+ ctrl->apm_adj_volt = CPR3_ROUND(ctrl->apm_adj_volt, ctrl->step_volt); -+ -+ ctrl->apm_high_supply = MSM_APM_SUPPLY_APCC; -+ ctrl->apm_low_supply = MSM_APM_SUPPLY_MX; -+ -+ return 0; -+} -+ -+/** -+ * cpr3_mem_acc_init() - initialize mem-acc regulator data for -+ * a CPR3 regulator -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_mem_acc_init(struct cpr3_regulator *vreg) -+{ -+ struct cpr3_controller *ctrl = vreg->thread->ctrl; -+ u32 *temp; -+ int i, rc; -+ -+ if (!ctrl->mem_acc_regulator) { -+ cpr3_info(ctrl, "not using memory accelerator regulator\n"); -+ return 0; -+ } -+ -+ temp = kcalloc(vreg->corner_count, sizeof(*temp), GFP_KERNEL); -+ if (!temp) -+ return -ENOMEM; -+ -+ rc = cpr3_parse_corner_array_property(vreg, "qcom,mem-acc-voltage", -+ 1, temp); -+ if (rc) { -+ cpr3_err(ctrl, "could not load mem-acc corners, rc=%d\n", rc); -+ } else { -+ for (i = 0; i < vreg->corner_count; i++) -+ vreg->corner[i].mem_acc_volt = temp[i]; -+ } -+ -+ kfree(temp); -+ return rc; -+} -+ -+/** -+ * cpr4_load_core_and_temp_adj() - parse amount of voltage adjustment for -+ * per-online-core and per-temperature voltage adjustment for a -+ * given corner or corner band from device tree. -+ * @vreg: Pointer to the CPR3 regulator -+ * @num: Corner number or corner band number -+ * @use_corner_band: Boolean indicating if the CPR3 regulator supports -+ * adjustments per corner band -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr4_load_core_and_temp_adj(struct cpr3_regulator *vreg, -+ int num, bool use_corner_band) -+{ -+ struct cpr3_controller *ctrl = vreg->thread->ctrl; -+ struct cpr4_sdelta *sdelta; -+ int sdelta_size, i, j, pos, rc = 0; -+ char str[75]; -+ size_t buflen; -+ char *buf; -+ -+ sdelta = use_corner_band ? vreg->corner_band[num].sdelta : -+ vreg->corner[num].sdelta; -+ -+ if (!sdelta->allow_core_count_adj && !sdelta->allow_temp_adj) { -+ /* corner doesn't need sdelta table */ -+ sdelta->max_core_count = 0; -+ sdelta->temp_band_count = 0; -+ return rc; -+ } -+ -+ sdelta_size = sdelta->max_core_count * sdelta->temp_band_count; -+ if (use_corner_band) -+ snprintf(str, sizeof(str), -+ "corner_band=%d core_config_count=%d temp_band_count=%d sdelta_size=%d\n", -+ num, sdelta->max_core_count, -+ sdelta->temp_band_count, sdelta_size); -+ else -+ snprintf(str, sizeof(str), -+ "corner=%d core_config_count=%d temp_band_count=%d sdelta_size=%d\n", -+ num, sdelta->max_core_count, -+ sdelta->temp_band_count, sdelta_size); -+ -+ cpr3_debug(vreg, "%s", str); -+ -+ sdelta->table = devm_kcalloc(ctrl->dev, sdelta_size, -+ sizeof(*sdelta->table), GFP_KERNEL); -+ if (!sdelta->table) -+ return -ENOMEM; -+ -+ if (use_corner_band) -+ snprintf(str, sizeof(str), -+ "qcom,cpr-corner-band%d-temp-core-voltage-adjustment", -+ num + CPR3_CORNER_OFFSET); -+ else -+ snprintf(str, sizeof(str), -+ "qcom,cpr-corner%d-temp-core-voltage-adjustment", -+ num + CPR3_CORNER_OFFSET); -+ -+ rc = cpr3_parse_array_property(vreg, str, sdelta_size, -+ sdelta->table); -+ if (rc) { -+ cpr3_err(vreg, "could not load %s, rc=%d\n", str, rc); -+ return rc; -+ } -+ -+ /* -+ * Convert sdelta margins from uV to PMIC steps and apply negation to -+ * follow the SDELTA register semantics. -+ */ -+ for (i = 0; i < sdelta_size; i++) -+ sdelta->table[i] = -(sdelta->table[i] / ctrl->step_volt); -+ -+ buflen = sizeof(*buf) * sdelta_size * (MAX_CHARS_PER_INT + 2); -+ buf = kzalloc(buflen, GFP_KERNEL); -+ if (!buf) -+ return rc; -+ -+ for (i = 0; i < sdelta->max_core_count; i++) { -+ for (j = 0, pos = 0; j < sdelta->temp_band_count; j++) -+ pos += scnprintf(buf + pos, buflen - pos, " %u", -+ sdelta->table[i * sdelta->temp_band_count + j]); -+ cpr3_debug(vreg, "sdelta[%d]:%s\n", i, buf); -+ } -+ -+ kfree(buf); -+ return rc; -+} -+ -+/** -+ * cpr4_parse_core_count_temp_voltage_adj() - parse configuration data for -+ * per-online-core and per-temperature voltage adjustment for -+ * a CPR3 regulator from device tree. -+ * @vreg: Pointer to the CPR3 regulator -+ * @use_corner_band: Boolean indicating if the CPR3 regulator supports -+ * adjustments per corner band -+ * -+ * This function supports parsing of per-online-core and per-temperature -+ * adjustments per corner or per corner band. CPR controllers which support -+ * corner bands apply the same adjustments to all corners within a corner band. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr4_parse_core_count_temp_voltage_adj( -+ struct cpr3_regulator *vreg, bool use_corner_band) -+{ -+ struct cpr3_controller *ctrl = vreg->thread->ctrl; -+ struct device_node *node = vreg->of_node; -+ struct cpr3_corner *corner; -+ struct cpr4_sdelta *sdelta; -+ int i, sdelta_table_count, rc = 0; -+ int *allow_core_count_adj = NULL, *allow_temp_adj = NULL; -+ char prop_str[75]; -+ -+ if (of_find_property(node, use_corner_band ? -+ "qcom,corner-band-allow-temp-adjustment" -+ : "qcom,corner-allow-temp-adjustment", NULL)) { -+ if (!ctrl->allow_temp_adj) { -+ cpr3_err(ctrl, "Temperature adjustment configurations missing\n"); -+ return -EINVAL; -+ } -+ -+ vreg->allow_temp_adj = true; -+ } -+ -+ if (of_find_property(node, use_corner_band ? -+ "qcom,corner-band-allow-core-count-adjustment" -+ : "qcom,corner-allow-core-count-adjustment", -+ NULL)) { -+ rc = of_property_read_u32(node, "qcom,max-core-count", -+ &vreg->max_core_count); -+ if (rc) { -+ cpr3_err(vreg, "error reading qcom,max-core-count, rc=%d\n", -+ rc); -+ return -EINVAL; -+ } -+ -+ vreg->allow_core_count_adj = true; -+ ctrl->allow_core_count_adj = true; -+ } -+ -+ if (!vreg->allow_temp_adj && !vreg->allow_core_count_adj) { -+ /* -+ * Both per-online-core and temperature based adjustments are -+ * disabled for this regulator. -+ */ -+ return 0; -+ } else if (!vreg->allow_core_count_adj) { -+ /* -+ * Only per-temperature voltage adjusments are allowed. -+ * Keep max core count value as 1 to allocate SDELTA. -+ */ -+ vreg->max_core_count = 1; -+ } -+ -+ if (vreg->allow_core_count_adj) { -+ allow_core_count_adj = kcalloc(vreg->corner_count, -+ sizeof(*allow_core_count_adj), -+ GFP_KERNEL); -+ if (!allow_core_count_adj) -+ return -ENOMEM; -+ -+ snprintf(prop_str, sizeof(prop_str), "%s", use_corner_band ? -+ "qcom,corner-band-allow-core-count-adjustment" : -+ "qcom,corner-allow-core-count-adjustment"); -+ -+ rc = use_corner_band ? -+ cpr3_parse_corner_band_array_property(vreg, prop_str, -+ 1, allow_core_count_adj) : -+ cpr3_parse_corner_array_property(vreg, prop_str, -+ 1, allow_core_count_adj); -+ if (rc) { -+ cpr3_err(vreg, "error reading %s, rc=%d\n", prop_str, -+ rc); -+ goto done; -+ } -+ } -+ -+ if (vreg->allow_temp_adj) { -+ allow_temp_adj = kcalloc(vreg->corner_count, -+ sizeof(*allow_temp_adj), GFP_KERNEL); -+ if (!allow_temp_adj) { -+ rc = -ENOMEM; -+ goto done; -+ } -+ -+ snprintf(prop_str, sizeof(prop_str), "%s", use_corner_band ? -+ "qcom,corner-band-allow-temp-adjustment" : -+ "qcom,corner-allow-temp-adjustment"); -+ -+ rc = use_corner_band ? -+ cpr3_parse_corner_band_array_property(vreg, prop_str, -+ 1, allow_temp_adj) : -+ cpr3_parse_corner_array_property(vreg, prop_str, -+ 1, allow_temp_adj); -+ if (rc) { -+ cpr3_err(vreg, "error reading %s, rc=%d\n", prop_str, -+ rc); -+ goto done; -+ } -+ } -+ -+ sdelta_table_count = use_corner_band ? vreg->corner_band_count : -+ vreg->corner_count; -+ -+ for (i = 0; i < sdelta_table_count; i++) { -+ sdelta = devm_kzalloc(ctrl->dev, sizeof(*corner->sdelta), -+ GFP_KERNEL); -+ if (!sdelta) { -+ rc = -ENOMEM; -+ goto done; -+ } -+ -+ if (allow_core_count_adj) -+ sdelta->allow_core_count_adj = allow_core_count_adj[i]; -+ if (allow_temp_adj) -+ sdelta->allow_temp_adj = allow_temp_adj[i]; -+ sdelta->max_core_count = vreg->max_core_count; -+ sdelta->temp_band_count = ctrl->temp_band_count; -+ -+ if (use_corner_band) -+ vreg->corner_band[i].sdelta = sdelta; -+ else -+ vreg->corner[i].sdelta = sdelta; -+ -+ rc = cpr4_load_core_and_temp_adj(vreg, i, use_corner_band); -+ if (rc) { -+ cpr3_err(vreg, "corner/band %d core and temp adjustment loading failed, rc=%d\n", -+ i, rc); -+ goto done; -+ } -+ } -+ -+done: -+ kfree(allow_core_count_adj); -+ kfree(allow_temp_adj); -+ -+ return rc; -+} -+ -+/** -+ * cprh_adjust_voltages_for_apm() - adjust per-corner floor and ceiling voltages -+ * so that they do not overlap the APM threshold voltage. -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * The memory array power mux (APM) must be configured for a specific supply -+ * based upon where the VDD voltage lies with respect to the APM threshold -+ * voltage. When using CPR hardware closed-loop, the voltage may vary anywhere -+ * between the floor and ceiling voltage without software notification. -+ * Therefore, it is required that the floor to ceiling range for every corner -+ * not intersect the APM threshold voltage. This function adjusts the floor to -+ * ceiling range for each corner which violates this requirement. -+ * -+ * The following algorithm is applied: -+ * if floor < threshold <= ceiling: -+ * if open_loop >= threshold, then floor = threshold - adj -+ * else ceiling = threshold - step -+ * where: -+ * adj = APM hysteresis voltage established to minimize the number of -+ * corners with artificially increased floor voltages -+ * step = voltage in microvolts of a single step of the VDD supply -+ * -+ * The open-loop voltage is also bounded by the new floor or ceiling value as -+ * needed. -+ * -+ * Return: none -+ */ -+void cprh_adjust_voltages_for_apm(struct cpr3_regulator *vreg) -+{ -+ struct cpr3_controller *ctrl = vreg->thread->ctrl; -+ struct cpr3_corner *corner; -+ int i, adj, threshold, prev_ceiling, prev_floor, prev_open_loop; -+ -+ if (!ctrl->apm_threshold_volt) { -+ /* APM not being used. */ -+ return; -+ } -+ -+ ctrl->apm_threshold_volt = CPR3_ROUND(ctrl->apm_threshold_volt, -+ ctrl->step_volt); -+ ctrl->apm_adj_volt = CPR3_ROUND(ctrl->apm_adj_volt, ctrl->step_volt); -+ -+ threshold = ctrl->apm_threshold_volt; -+ adj = ctrl->apm_adj_volt; -+ -+ for (i = 0; i < vreg->corner_count; i++) { -+ corner = &vreg->corner[i]; -+ -+ if (threshold <= corner->floor_volt -+ || threshold > corner->ceiling_volt) -+ continue; -+ -+ prev_floor = corner->floor_volt; -+ prev_ceiling = corner->ceiling_volt; -+ prev_open_loop = corner->open_loop_volt; -+ -+ if (corner->open_loop_volt >= threshold) { -+ corner->floor_volt = max(corner->floor_volt, -+ threshold - adj); -+ if (corner->open_loop_volt < corner->floor_volt) -+ corner->open_loop_volt = corner->floor_volt; -+ } else { -+ corner->ceiling_volt = threshold - ctrl->step_volt; -+ } -+ -+ if (corner->floor_volt != prev_floor -+ || corner->ceiling_volt != prev_ceiling -+ || corner->open_loop_volt != prev_open_loop) -+ cpr3_debug(vreg, "APM threshold=%d, APM adj=%d changed corner %d voltages; prev: floor=%d, ceiling=%d, open-loop=%d; new: floor=%d, ceiling=%d, open-loop=%d\n", -+ threshold, adj, i, prev_floor, prev_ceiling, -+ prev_open_loop, corner->floor_volt, -+ corner->ceiling_volt, corner->open_loop_volt); -+ } -+} -+ -+/** -+ * cprh_adjust_voltages_for_mem_acc() - adjust per-corner floor and ceiling -+ * voltages so that they do not intersect the MEM ACC threshold -+ * voltage -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * The following algorithm is applied: -+ * if floor < threshold <= ceiling: -+ * if open_loop >= threshold, then floor = threshold -+ * else ceiling = threshold - step -+ * where: -+ * step = voltage in microvolts of a single step of the VDD supply -+ * -+ * The open-loop voltage is also bounded by the new floor or ceiling value as -+ * needed. -+ * -+ * Return: none -+ */ -+void cprh_adjust_voltages_for_mem_acc(struct cpr3_regulator *vreg) -+{ -+ struct cpr3_controller *ctrl = vreg->thread->ctrl; -+ struct cpr3_corner *corner; -+ int i, threshold, prev_ceiling, prev_floor, prev_open_loop; -+ -+ if (!ctrl->mem_acc_threshold_volt) { -+ /* MEM ACC not being used. */ -+ return; -+ } -+ -+ ctrl->mem_acc_threshold_volt = CPR3_ROUND(ctrl->mem_acc_threshold_volt, -+ ctrl->step_volt); -+ -+ threshold = ctrl->mem_acc_threshold_volt; -+ -+ for (i = 0; i < vreg->corner_count; i++) { -+ corner = &vreg->corner[i]; -+ -+ if (threshold <= corner->floor_volt -+ || threshold > corner->ceiling_volt) -+ continue; -+ -+ prev_floor = corner->floor_volt; -+ prev_ceiling = corner->ceiling_volt; -+ prev_open_loop = corner->open_loop_volt; -+ -+ if (corner->open_loop_volt >= threshold) { -+ corner->floor_volt = max(corner->floor_volt, threshold); -+ if (corner->open_loop_volt < corner->floor_volt) -+ corner->open_loop_volt = corner->floor_volt; -+ } else { -+ corner->ceiling_volt = threshold - ctrl->step_volt; -+ } -+ -+ if (corner->floor_volt != prev_floor -+ || corner->ceiling_volt != prev_ceiling -+ || corner->open_loop_volt != prev_open_loop) -+ cpr3_debug(vreg, "MEM ACC threshold=%d changed corner %d voltages; prev: floor=%d, ceiling=%d, open-loop=%d; new: floor=%d, ceiling=%d, open-loop=%d\n", -+ threshold, i, prev_floor, prev_ceiling, -+ prev_open_loop, corner->floor_volt, -+ corner->ceiling_volt, corner->open_loop_volt); -+ } -+} -+ -+/** -+ * cpr3_apply_closed_loop_offset_voltages() - modify the closed-loop voltage -+ * adjustments by the amounts that are needed for this -+ * fuse combo -+ * @vreg: Pointer to the CPR3 regulator -+ * @volt_adjust: Array of closed-loop voltage adjustment values of length -+ * vreg->corner_count which is further adjusted based upon -+ * offset voltage fuse values. -+ * @fuse_volt_adjust: Fused closed-loop voltage adjustment values of length -+ * vreg->fuse_corner_count. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr3_apply_closed_loop_offset_voltages(struct cpr3_regulator *vreg, -+ int *volt_adjust, int *fuse_volt_adjust) -+{ -+ u32 *corner_map; -+ int rc = 0, i; -+ -+ if (!of_find_property(vreg->of_node, -+ "qcom,cpr-fused-closed-loop-voltage-adjustment-map", NULL)) { -+ /* No closed-loop offset required. */ -+ return 0; -+ } -+ -+ corner_map = kcalloc(vreg->corner_count, sizeof(*corner_map), -+ GFP_KERNEL); -+ if (!corner_map) -+ return -ENOMEM; -+ -+ rc = cpr3_parse_corner_array_property(vreg, -+ "qcom,cpr-fused-closed-loop-voltage-adjustment-map", -+ 1, corner_map); -+ if (rc) -+ goto done; -+ -+ for (i = 0; i < vreg->corner_count; i++) { -+ if (corner_map[i] == 0) { -+ continue; -+ } else if (corner_map[i] > vreg->fuse_corner_count) { -+ cpr3_err(vreg, "corner %d mapped to invalid fuse corner: %u\n", -+ i, corner_map[i]); -+ rc = -EINVAL; -+ goto done; -+ } -+ -+ volt_adjust[i] += fuse_volt_adjust[corner_map[i] - 1]; -+ } -+ -+done: -+ kfree(corner_map); -+ return rc; -+} -+ -+/** -+ * cpr3_enforce_inc_quotient_monotonicity() - Ensure that target quotients -+ * increase monotonically from lower to higher corners -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static void cpr3_enforce_inc_quotient_monotonicity(struct cpr3_regulator *vreg) -+{ -+ int i, j; -+ -+ for (i = 1; i < vreg->corner_count; i++) { -+ for (j = 0; j < CPR3_RO_COUNT; j++) { -+ if (vreg->corner[i].target_quot[j] -+ && vreg->corner[i].target_quot[j] -+ < vreg->corner[i - 1].target_quot[j]) { -+ cpr3_debug(vreg, "corner %d RO%u target quot=%u < corner %d RO%u target quot=%u; overriding: corner %d RO%u target quot=%u\n", -+ i, j, -+ vreg->corner[i].target_quot[j], -+ i - 1, j, -+ vreg->corner[i - 1].target_quot[j], -+ i, j, -+ vreg->corner[i - 1].target_quot[j]); -+ vreg->corner[i].target_quot[j] -+ = vreg->corner[i - 1].target_quot[j]; -+ } -+ } -+ } -+} -+ -+/** -+ * cpr3_enforce_dec_quotient_monotonicity() - Ensure that target quotients -+ * decrease monotonically from higher to lower corners -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static void cpr3_enforce_dec_quotient_monotonicity(struct cpr3_regulator *vreg) -+{ -+ int i, j; -+ -+ for (i = vreg->corner_count - 2; i >= 0; i--) { -+ for (j = 0; j < CPR3_RO_COUNT; j++) { -+ if (vreg->corner[i + 1].target_quot[j] -+ && vreg->corner[i].target_quot[j] -+ > vreg->corner[i + 1].target_quot[j]) { -+ cpr3_debug(vreg, "corner %d RO%u target quot=%u > corner %d RO%u target quot=%u; overriding: corner %d RO%u target quot=%u\n", -+ i, j, -+ vreg->corner[i].target_quot[j], -+ i + 1, j, -+ vreg->corner[i + 1].target_quot[j], -+ i, j, -+ vreg->corner[i + 1].target_quot[j]); -+ vreg->corner[i].target_quot[j] -+ = vreg->corner[i + 1].target_quot[j]; -+ } -+ } -+ } -+} -+ -+/** -+ * _cpr3_adjust_target_quotients() - adjust the target quotients for each -+ * corner of the regulator according to input adjustment and -+ * scaling arrays -+ * @vreg: Pointer to the CPR3 regulator -+ * @volt_adjust: Pointer to an array of closed-loop voltage adjustments -+ * with units of microvolts. The array must have -+ * vreg->corner_count number of elements. -+ * @ro_scale: Pointer to a flattened 2D array of RO scaling factors. -+ * The array must have an inner dimension of CPR3_RO_COUNT -+ * and an outer dimension of vreg->corner_count -+ * @label: Null terminated string providing a label for the type -+ * of adjustment. -+ * -+ * Return: true if any corners received a positive voltage adjustment (> 0), -+ * else false -+ */ -+static bool _cpr3_adjust_target_quotients(struct cpr3_regulator *vreg, -+ const int *volt_adjust, const int *ro_scale, const char *label) -+{ -+ int i, j, quot_adjust; -+ bool is_increasing = false; -+ u32 prev_quot; -+ -+ for (i = 0; i < vreg->corner_count; i++) { -+ for (j = 0; j < CPR3_RO_COUNT; j++) { -+ if (vreg->corner[i].target_quot[j]) { -+ quot_adjust = cpr3_quot_adjustment( -+ ro_scale[i * CPR3_RO_COUNT + j], -+ volt_adjust[i]); -+ if (quot_adjust) { -+ prev_quot = vreg->corner[i]. -+ target_quot[j]; -+ vreg->corner[i].target_quot[j] -+ += quot_adjust; -+ cpr3_debug(vreg, "adjusted corner %d RO%d target quot %s: %u --> %u (%d uV)\n", -+ i, j, label, prev_quot, -+ vreg->corner[i].target_quot[j], -+ volt_adjust[i]); -+ } -+ } -+ } -+ if (volt_adjust[i] > 0) -+ is_increasing = true; -+ } -+ -+ return is_increasing; -+} -+ -+/** -+ * cpr3_adjust_target_quotients() - adjust the target quotients for each -+ * corner according to device tree values and fuse values -+ * @vreg: Pointer to the CPR3 regulator -+ * @fuse_volt_adjust: Fused closed-loop voltage adjustment values of length -+ * vreg->fuse_corner_count. This parameter could be null -+ * pointer when no fused adjustments are needed. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+int cpr3_adjust_target_quotients(struct cpr3_regulator *vreg, -+ int *fuse_volt_adjust) -+{ -+ int i, rc; -+ int *volt_adjust, *ro_scale; -+ bool explicit_adjustment, fused_adjustment, is_increasing; -+ -+ explicit_adjustment = of_find_property(vreg->of_node, -+ "qcom,cpr-closed-loop-voltage-adjustment", NULL); -+ fused_adjustment = of_find_property(vreg->of_node, -+ "qcom,cpr-fused-closed-loop-voltage-adjustment-map", NULL); -+ -+ if (!explicit_adjustment && !fused_adjustment && !vreg->aging_allowed) { -+ /* No adjustment required. */ -+ return 0; -+ } else if (!of_find_property(vreg->of_node, -+ "qcom,cpr-ro-scaling-factor", NULL)) { -+ cpr3_err(vreg, "qcom,cpr-ro-scaling-factor is required for closed-loop voltage adjustment, but is missing\n"); -+ return -EINVAL; -+ } -+ -+ volt_adjust = kcalloc(vreg->corner_count, sizeof(*volt_adjust), -+ GFP_KERNEL); -+ ro_scale = kcalloc(vreg->corner_count * CPR3_RO_COUNT, -+ sizeof(*ro_scale), GFP_KERNEL); -+ if (!volt_adjust || !ro_scale) { -+ rc = -ENOMEM; -+ goto done; -+ } -+ -+ rc = cpr3_parse_corner_array_property(vreg, -+ "qcom,cpr-ro-scaling-factor", CPR3_RO_COUNT, ro_scale); -+ if (rc) { -+ cpr3_err(vreg, "could not load RO scaling factors, rc=%d\n", -+ rc); -+ goto done; -+ } -+ -+ for (i = 0; i < vreg->corner_count; i++) -+ memcpy(vreg->corner[i].ro_scale, &ro_scale[i * CPR3_RO_COUNT], -+ sizeof(*ro_scale) * CPR3_RO_COUNT); -+ -+ if (explicit_adjustment) { -+ rc = cpr3_parse_corner_array_property(vreg, -+ "qcom,cpr-closed-loop-voltage-adjustment", -+ 1, volt_adjust); -+ if (rc) { -+ cpr3_err(vreg, "could not load closed-loop voltage adjustments, rc=%d\n", -+ rc); -+ goto done; -+ } -+ -+ _cpr3_adjust_target_quotients(vreg, volt_adjust, ro_scale, -+ "from DT"); -+ cpr3_enforce_inc_quotient_monotonicity(vreg); -+ } -+ -+ if (fused_adjustment && fuse_volt_adjust) { -+ memset(volt_adjust, 0, -+ sizeof(*volt_adjust) * vreg->corner_count); -+ -+ rc = cpr3_apply_closed_loop_offset_voltages(vreg, volt_adjust, -+ fuse_volt_adjust); -+ if (rc) { -+ cpr3_err(vreg, "could not apply fused closed-loop voltage reductions, rc=%d\n", -+ rc); -+ goto done; -+ } -+ -+ is_increasing = _cpr3_adjust_target_quotients(vreg, volt_adjust, -+ ro_scale, "from fuse"); -+ if (is_increasing) -+ cpr3_enforce_inc_quotient_monotonicity(vreg); -+ else -+ cpr3_enforce_dec_quotient_monotonicity(vreg); -+ } -+ -+done: -+ kfree(volt_adjust); -+ kfree(ro_scale); -+ return rc; -+} ---- /dev/null -+++ b/drivers/regulator/cpr4-apss-regulator.c -@@ -0,0 +1,1819 @@ -+/* -+ * Copyright (c) 2015-2016, The Linux Foundation. All rights reserved. -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 and -+ * only version 2 as published by the Free Software Foundation. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ */ -+ -+#define pr_fmt(fmt) "%s: " fmt, __func__ -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#include "cpr3-regulator.h" -+ -+#define IPQ807x_APSS_FUSE_CORNERS 4 -+#define IPQ817x_APPS_FUSE_CORNERS 2 -+#define IPQ6018_APSS_FUSE_CORNERS 4 -+#define IPQ9574_APSS_FUSE_CORNERS 4 -+ -+u32 g_valid_fuse_count = IPQ807x_APSS_FUSE_CORNERS; -+ -+/** -+ * struct cpr4_ipq807x_apss_fuses - APSS specific fuse data for IPQ807x -+ * @ro_sel: Ring oscillator select fuse parameter value for each -+ * fuse corner -+ * @init_voltage: Initial (i.e. open-loop) voltage fuse parameter value -+ * for each fuse corner (raw, not converted to a voltage) -+ * @target_quot: CPR target quotient fuse parameter value for each fuse -+ * corner -+ * @quot_offset: CPR target quotient offset fuse parameter value for each -+ * fuse corner (raw, not unpacked) used for target quotient -+ * interpolation -+ * @speed_bin: Application processor speed bin fuse parameter value for -+ * the given chip -+ * @cpr_fusing_rev: CPR fusing revision fuse parameter value -+ * @boost_cfg: CPR boost configuration fuse parameter value -+ * @boost_voltage: CPR boost voltage fuse parameter value (raw, not -+ * converted to a voltage) -+ * -+ * This struct holds the values for all of the fuses read from memory. -+ */ -+struct cpr4_ipq807x_apss_fuses { -+ u64 ro_sel[IPQ807x_APSS_FUSE_CORNERS]; -+ u64 init_voltage[IPQ807x_APSS_FUSE_CORNERS]; -+ u64 target_quot[IPQ807x_APSS_FUSE_CORNERS]; -+ u64 quot_offset[IPQ807x_APSS_FUSE_CORNERS]; -+ u64 speed_bin; -+ u64 cpr_fusing_rev; -+ u64 boost_cfg; -+ u64 boost_voltage; -+ u64 misc; -+}; -+ -+/* -+ * fuse combo = fusing revision + 8 * (speed bin) -+ * where: fusing revision = 0 - 7 and speed bin = 0 - 7 -+ */ -+#define CPR4_IPQ807x_APSS_FUSE_COMBO_COUNT 64 -+ -+/* -+ * Constants which define the name of each fuse corner. -+ */ -+enum cpr4_ipq807x_apss_fuse_corner { -+ CPR4_IPQ807x_APSS_FUSE_CORNER_SVS = 0, -+ CPR4_IPQ807x_APSS_FUSE_CORNER_NOM = 1, -+ CPR4_IPQ807x_APSS_FUSE_CORNER_TURBO = 2, -+ CPR4_IPQ807x_APSS_FUSE_CORNER_STURBO = 3, -+}; -+ -+static const char * const cpr4_ipq807x_apss_fuse_corner_name[] = { -+ [CPR4_IPQ807x_APSS_FUSE_CORNER_SVS] = "SVS", -+ [CPR4_IPQ807x_APSS_FUSE_CORNER_NOM] = "NOM", -+ [CPR4_IPQ807x_APSS_FUSE_CORNER_TURBO] = "TURBO", -+ [CPR4_IPQ807x_APSS_FUSE_CORNER_STURBO] = "STURBO", -+}; -+ -+/* -+ * IPQ807x APSS fuse parameter locations: -+ * -+ * Structs are organized with the following dimensions: -+ * Outer: 0 to 3 for fuse corners from lowest to highest corner -+ * Inner: large enough to hold the longest set of parameter segments which -+ * fully defines a fuse parameter, +1 (for NULL termination). -+ * Each segment corresponds to a contiguous group of bits from a -+ * single fuse row. These segments are concatentated together in -+ * order to form the full fuse parameter value. The segments for -+ * a given parameter may correspond to different fuse rows. -+ */ -+static struct cpr3_fuse_param -+ipq807x_apss_ro_sel_param[IPQ807x_APSS_FUSE_CORNERS][2] = { -+ {{73, 8, 11}, {} }, -+ {{73, 4, 7}, {} }, -+ {{73, 0, 3}, {} }, -+ {{73, 12, 15}, {} }, -+}; -+ -+static struct cpr3_fuse_param -+ipq807x_apss_init_voltage_param[IPQ807x_APSS_FUSE_CORNERS][2] = { -+ {{71, 18, 23}, {} }, -+ {{71, 12, 17}, {} }, -+ {{71, 6, 11}, {} }, -+ {{71, 0, 5}, {} }, -+}; -+ -+static struct cpr3_fuse_param -+ipq807x_apss_target_quot_param[IPQ807x_APSS_FUSE_CORNERS][2] = { -+ {{72, 32, 43}, {} }, -+ {{72, 20, 31}, {} }, -+ {{72, 8, 19}, {} }, -+ {{72, 44, 55}, {} }, -+}; -+ -+static struct cpr3_fuse_param -+ipq807x_apss_quot_offset_param[IPQ807x_APSS_FUSE_CORNERS][2] = { -+ {{} }, -+ {{71, 46, 52}, {} }, -+ {{71, 39, 45}, {} }, -+ {{71, 32, 38}, {} }, -+}; -+ -+static struct cpr3_fuse_param ipq807x_cpr_fusing_rev_param[] = { -+ {71, 53, 55}, -+ {}, -+}; -+ -+static struct cpr3_fuse_param ipq807x_apss_speed_bin_param[] = { -+ {36, 40, 42}, -+ {}, -+}; -+ -+static struct cpr3_fuse_param ipq807x_cpr_boost_fuse_cfg_param[] = { -+ {36, 43, 45}, -+ {}, -+}; -+ -+static struct cpr3_fuse_param ipq807x_apss_boost_fuse_volt_param[] = { -+ {71, 0, 5}, -+ {}, -+}; -+ -+static struct cpr3_fuse_param ipq807x_misc_fuse_volt_adj_param[] = { -+ {36, 54, 54}, -+ {}, -+}; -+ -+static struct cpr3_fuse_parameters ipq807x_fuse_params = { -+ .apss_ro_sel_param = ipq807x_apss_ro_sel_param, -+ .apss_init_voltage_param = ipq807x_apss_init_voltage_param, -+ .apss_target_quot_param = ipq807x_apss_target_quot_param, -+ .apss_quot_offset_param = ipq807x_apss_quot_offset_param, -+ .cpr_fusing_rev_param = ipq807x_cpr_fusing_rev_param, -+ .apss_speed_bin_param = ipq807x_apss_speed_bin_param, -+ .cpr_boost_fuse_cfg_param = ipq807x_cpr_boost_fuse_cfg_param, -+ .apss_boost_fuse_volt_param = ipq807x_apss_boost_fuse_volt_param, -+ .misc_fuse_volt_adj_param = ipq807x_misc_fuse_volt_adj_param -+}; -+ -+/* -+ * The number of possible values for misc fuse is -+ * 2^(#bits defined for misc fuse) -+ */ -+#define IPQ807x_MISC_FUSE_VAL_COUNT BIT(1) -+ -+/* -+ * Open loop voltage fuse reference voltages in microvolts for IPQ807x -+ */ -+static int ipq807x_apss_fuse_ref_volt -+ [IPQ807x_APSS_FUSE_CORNERS] = { -+ 720000, -+ 864000, -+ 992000, -+ 1064000, -+}; -+ -+#define IPQ807x_APSS_FUSE_STEP_VOLT 8000 -+#define IPQ807x_APSS_VOLTAGE_FUSE_SIZE 6 -+#define IPQ807x_APSS_QUOT_OFFSET_SCALE 5 -+ -+#define IPQ807x_APSS_CPR_SENSOR_COUNT 6 -+ -+#define IPQ807x_APSS_CPR_CLOCK_RATE 19200000 -+ -+#define IPQ807x_APSS_MAX_TEMP_POINTS 3 -+#define IPQ807x_APSS_TEMP_SENSOR_ID_START 4 -+#define IPQ807x_APSS_TEMP_SENSOR_ID_END 13 -+/* -+ * Boost voltage fuse reference and ceiling voltages in microvolts for -+ * IPQ807x. -+ */ -+#define IPQ807x_APSS_BOOST_FUSE_REF_VOLT 1140000 -+#define IPQ807x_APSS_BOOST_CEILING_VOLT 1140000 -+#define IPQ807x_APSS_BOOST_FLOOR_VOLT 900000 -+#define MAX_BOOST_CONFIG_FUSE_VALUE 8 -+ -+#define IPQ807x_APSS_CPR_SDELTA_CORE_COUNT 15 -+ -+#define IPQ807x_APSS_CPR_TCSR_START 8 -+#define IPQ807x_APSS_CPR_TCSR_END 9 -+ -+/* -+ * Array of integer values mapped to each of the boost config fuse values to -+ * indicate boost enable/disable status. -+ */ -+static bool boost_fuse[MAX_BOOST_CONFIG_FUSE_VALUE] = {0, 1, 1, 1, 1, 1, 1, 1}; -+ -+/* -+ * IPQ6018 (Few parameters are changed, remaining are same as IPQ807x) -+ */ -+#define IPQ6018_APSS_FUSE_STEP_VOLT 12500 -+#define IPQ6018_APSS_CPR_CLOCK_RATE 24000000 -+ -+static struct cpr3_fuse_param -+ipq6018_apss_ro_sel_param[IPQ6018_APSS_FUSE_CORNERS][2] = { -+ {{75, 8, 11}, {} }, -+ {{75, 4, 7}, {} }, -+ {{75, 0, 3}, {} }, -+ {{75, 12, 15}, {} }, -+}; -+ -+static struct cpr3_fuse_param -+ipq6018_apss_init_voltage_param[IPQ6018_APSS_FUSE_CORNERS][2] = { -+ {{73, 18, 23}, {} }, -+ {{73, 12, 17}, {} }, -+ {{73, 6, 11}, {} }, -+ {{73, 0, 5}, {} }, -+}; -+ -+static struct cpr3_fuse_param -+ipq6018_apss_target_quot_param[IPQ6018_APSS_FUSE_CORNERS][2] = { -+ {{74, 32, 43}, {} }, -+ {{74, 20, 31}, {} }, -+ {{74, 8, 19}, {} }, -+ {{74, 44, 55}, {} }, -+}; -+ -+static struct cpr3_fuse_param -+ipq6018_apss_quot_offset_param[IPQ6018_APSS_FUSE_CORNERS][2] = { -+ {{} }, -+ {{73, 48, 55}, {} }, -+ {{73, 40, 47}, {} }, -+ {{73, 32, 39}, {} }, -+}; -+ -+static struct cpr3_fuse_param ipq6018_cpr_fusing_rev_param[] = { -+ {75, 16, 18}, -+ {}, -+}; -+ -+static struct cpr3_fuse_param ipq6018_apss_speed_bin_param[] = { -+ {36, 40, 42}, -+ {}, -+}; -+ -+static struct cpr3_fuse_param ipq6018_cpr_boost_fuse_cfg_param[] = { -+ {36, 43, 45}, -+ {}, -+}; -+ -+static struct cpr3_fuse_param ipq6018_apss_boost_fuse_volt_param[] = { -+ {73, 0, 5}, -+ {}, -+}; -+ -+static struct cpr3_fuse_param ipq6018_misc_fuse_volt_adj_param[] = { -+ {36, 54, 54}, -+ {}, -+}; -+ -+static struct cpr3_fuse_parameters ipq6018_fuse_params = { -+ .apss_ro_sel_param = ipq6018_apss_ro_sel_param, -+ .apss_init_voltage_param = ipq6018_apss_init_voltage_param, -+ .apss_target_quot_param = ipq6018_apss_target_quot_param, -+ .apss_quot_offset_param = ipq6018_apss_quot_offset_param, -+ .cpr_fusing_rev_param = ipq6018_cpr_fusing_rev_param, -+ .apss_speed_bin_param = ipq6018_apss_speed_bin_param, -+ .cpr_boost_fuse_cfg_param = ipq6018_cpr_boost_fuse_cfg_param, -+ .apss_boost_fuse_volt_param = ipq6018_apss_boost_fuse_volt_param, -+ .misc_fuse_volt_adj_param = ipq6018_misc_fuse_volt_adj_param -+}; -+ -+ -+/* -+ * Boost voltage fuse reference and ceiling voltages in microvolts for -+ * IPQ6018. -+ */ -+#define IPQ6018_APSS_BOOST_FUSE_REF_VOLT 1140000 -+#define IPQ6018_APSS_BOOST_CEILING_VOLT 1140000 -+#define IPQ6018_APSS_BOOST_FLOOR_VOLT 900000 -+ -+/* -+ * Open loop voltage fuse reference voltages in microvolts for IPQ807x -+ */ -+static int ipq6018_apss_fuse_ref_volt -+ [IPQ6018_APSS_FUSE_CORNERS] = { -+ 725000, -+ 862500, -+ 987500, -+ 1062500, -+}; -+ -+/* -+ * IPQ6018 Memory ACC settings on TCSR -+ * -+ * Turbo_L1: write TCSR_MEM_ACC_SW_OVERRIDE_LEGACY_APC0 0x10 -+ * write TCSR_CUSTOM_VDDAPC0_ACC_1 0x1 -+ * Other modes: write TCSR_MEM_ACC_SW_OVERRIDE_LEGACY_APC0 0x0 -+ * write TCSR_CUSTOM_VDDAPC0_ACC_1 0x0 -+ * -+ */ -+#define IPQ6018_APSS_MEM_ACC_TCSR_COUNT 2 -+#define TCSR_MEM_ACC_SW_OVERRIDE_LEGACY_APC0 0x1946178 -+#define TCSR_CUSTOM_VDDAPC0_ACC_1 0x1946124 -+ -+struct mem_acc_tcsr { -+ u32 phy_addr; -+ void __iomem *ioremap_addr; -+ u32 value; -+}; -+ -+static struct mem_acc_tcsr ipq6018_mem_acc_tcsr[IPQ6018_APSS_MEM_ACC_TCSR_COUNT] = { -+ {TCSR_MEM_ACC_SW_OVERRIDE_LEGACY_APC0, NULL, 0x10}, -+ {TCSR_CUSTOM_VDDAPC0_ACC_1, NULL, 0x1}, -+}; -+ -+/* -+ * IPQ9574 (Few parameters are changed, remaining are same as IPQ6018) -+ */ -+#define IPQ9574_APSS_FUSE_STEP_VOLT 10000 -+ -+static struct cpr3_fuse_param -+ipq9574_apss_ro_sel_param[IPQ9574_APSS_FUSE_CORNERS][2] = { -+ {{107, 4, 7}, {} }, -+ {{107, 0, 3}, {} }, -+ {{106, 4, 7}, {} }, -+ {{106, 0, 3}, {} }, -+}; -+ -+static struct cpr3_fuse_param -+ipq9574_apss_init_voltage_param[IPQ9574_APSS_FUSE_CORNERS][2] = { -+ {{104, 24, 29}, {} }, -+ {{104, 18, 23}, {} }, -+ {{104, 12, 17}, {} }, -+ {{104, 6, 11}, {} }, -+}; -+ -+static struct cpr3_fuse_param -+ipq9574_apss_target_quot_param[IPQ9574_APSS_FUSE_CORNERS][2] = { -+ {{106, 32, 43}, {} }, -+ {{106, 20, 31}, {} }, -+ {{106, 8, 19}, {} }, -+ {{106, 44, 55}, {} }, -+}; -+ -+static struct cpr3_fuse_param -+ipq9574_apss_quot_offset_param[IPQ9574_APSS_FUSE_CORNERS][2] = { -+ {{} }, -+ {{105, 48, 55}, {} }, -+ {{105, 40, 47}, {} }, -+ {{105, 32, 39}, {} }, -+}; -+ -+static struct cpr3_fuse_param ipq9574_cpr_fusing_rev_param[] = { -+ {107, 8, 10}, -+ {}, -+}; -+ -+static struct cpr3_fuse_param ipq9574_apss_speed_bin_param[] = { -+ {0, 40, 42}, -+ {}, -+}; -+ -+static struct cpr3_fuse_param ipq9574_cpr_boost_fuse_cfg_param[] = { -+ {0, 43, 45}, -+ {}, -+}; -+ -+static struct cpr3_fuse_param ipq9574_apss_boost_fuse_volt_param[] = { -+ {104, 0, 5}, -+ {}, -+}; -+ -+static struct cpr3_fuse_param ipq9574_misc_fuse_volt_adj_param[] = { -+ {0, 54, 54}, -+ {}, -+}; -+ -+static struct cpr3_fuse_parameters ipq9574_fuse_params = { -+ .apss_ro_sel_param = ipq9574_apss_ro_sel_param, -+ .apss_init_voltage_param = ipq9574_apss_init_voltage_param, -+ .apss_target_quot_param = ipq9574_apss_target_quot_param, -+ .apss_quot_offset_param = ipq9574_apss_quot_offset_param, -+ .cpr_fusing_rev_param = ipq9574_cpr_fusing_rev_param, -+ .apss_speed_bin_param = ipq9574_apss_speed_bin_param, -+ .cpr_boost_fuse_cfg_param = ipq9574_cpr_boost_fuse_cfg_param, -+ .apss_boost_fuse_volt_param = ipq9574_apss_boost_fuse_volt_param, -+ .misc_fuse_volt_adj_param = ipq9574_misc_fuse_volt_adj_param -+}; -+ -+/* -+ * Open loop voltage fuse reference voltages in microvolts for IPQ9574 -+ */ -+static int ipq9574_apss_fuse_ref_volt -+ [IPQ9574_APSS_FUSE_CORNERS] = { -+ 725000, -+ 862500, -+ 987500, -+ 1062500, -+}; -+ -+/** -+ * cpr4_ipq807x_apss_read_fuse_data() - load APSS specific fuse parameter values -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * This function allocates a cpr4_ipq807x_apss_fuses struct, fills it with -+ * values read out of hardware fuses, and finally copies common fuse values -+ * into the CPR3 regulator struct. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr4_ipq807x_apss_read_fuse_data(struct cpr3_regulator *vreg) -+{ -+ void __iomem *base = vreg->thread->ctrl->fuse_base; -+ struct cpr4_ipq807x_apss_fuses *fuse; -+ int i, rc; -+ -+ fuse = devm_kzalloc(vreg->thread->ctrl->dev, sizeof(*fuse), GFP_KERNEL); -+ if (!fuse) -+ return -ENOMEM; -+ -+ rc = cpr3_read_fuse_param(base, vreg->cpr4_regulator_data->cpr3_fuse_params->apss_speed_bin_param, -+ &fuse->speed_bin); -+ if (rc) { -+ cpr3_err(vreg, "Unable to read speed bin fuse, rc=%d\n", rc); -+ return rc; -+ } -+ cpr3_info(vreg, "speed bin = %llu\n", fuse->speed_bin); -+ -+ rc = cpr3_read_fuse_param(base, vreg->cpr4_regulator_data->cpr3_fuse_params->cpr_fusing_rev_param, -+ &fuse->cpr_fusing_rev); -+ if (rc) { -+ cpr3_err(vreg, "Unable to read CPR fusing revision fuse, rc=%d\n", -+ rc); -+ return rc; -+ } -+ cpr3_info(vreg, "CPR fusing revision = %llu\n", fuse->cpr_fusing_rev); -+ -+ rc = cpr3_read_fuse_param(base, vreg->cpr4_regulator_data->cpr3_fuse_params->misc_fuse_volt_adj_param, -+ &fuse->misc); -+ if (rc) { -+ cpr3_err(vreg, "Unable to read misc voltage adjustment fuse, rc=%d\n", -+ rc); -+ return rc; -+ } -+ cpr3_info(vreg, "CPR misc fuse value = %llu\n", fuse->misc); -+ if (fuse->misc >= IPQ807x_MISC_FUSE_VAL_COUNT) { -+ cpr3_err(vreg, "CPR misc fuse value = %llu, should be < %lu\n", -+ fuse->misc, IPQ807x_MISC_FUSE_VAL_COUNT); -+ return -EINVAL; -+ } -+ -+ for (i = 0; i < g_valid_fuse_count; i++) { -+ rc = cpr3_read_fuse_param(base, -+ vreg->cpr4_regulator_data->cpr3_fuse_params->apss_init_voltage_param[i], -+ &fuse->init_voltage[i]); -+ if (rc) { -+ cpr3_err(vreg, "Unable to read fuse-corner %d initial voltage fuse, rc=%d\n", -+ i, rc); -+ return rc; -+ } -+ -+ rc = cpr3_read_fuse_param(base, -+ vreg->cpr4_regulator_data->cpr3_fuse_params->apss_target_quot_param[i], -+ &fuse->target_quot[i]); -+ if (rc) { -+ cpr3_err(vreg, "Unable to read fuse-corner %d target quotient fuse, rc=%d\n", -+ i, rc); -+ return rc; -+ } -+ -+ rc = cpr3_read_fuse_param(base, -+ vreg->cpr4_regulator_data->cpr3_fuse_params->apss_ro_sel_param[i], -+ &fuse->ro_sel[i]); -+ if (rc) { -+ cpr3_err(vreg, "Unable to read fuse-corner %d RO select fuse, rc=%d\n", -+ i, rc); -+ return rc; -+ } -+ -+ rc = cpr3_read_fuse_param(base, -+ vreg->cpr4_regulator_data->cpr3_fuse_params->apss_quot_offset_param[i], -+ &fuse->quot_offset[i]); -+ if (rc) { -+ cpr3_err(vreg, "Unable to read fuse-corner %d quotient offset fuse, rc=%d\n", -+ i, rc); -+ return rc; -+ } -+ } -+ -+ rc = cpr3_read_fuse_param(base, vreg->cpr4_regulator_data->cpr3_fuse_params->cpr_boost_fuse_cfg_param, -+ &fuse->boost_cfg); -+ if (rc) { -+ cpr3_err(vreg, "Unable to read CPR boost config fuse, rc=%d\n", -+ rc); -+ return rc; -+ } -+ cpr3_info(vreg, "Voltage boost fuse config = %llu boost = %s\n", -+ fuse->boost_cfg, boost_fuse[fuse->boost_cfg] -+ ? "enable" : "disable"); -+ -+ rc = cpr3_read_fuse_param(base, -+ vreg->cpr4_regulator_data->cpr3_fuse_params->apss_boost_fuse_volt_param, -+ &fuse->boost_voltage); -+ if (rc) { -+ cpr3_err(vreg, "failed to read boost fuse voltage, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ vreg->fuse_combo = fuse->cpr_fusing_rev + 8 * fuse->speed_bin; -+ if (vreg->fuse_combo >= CPR4_IPQ807x_APSS_FUSE_COMBO_COUNT) { -+ cpr3_err(vreg, "invalid CPR fuse combo = %d found\n", -+ vreg->fuse_combo); -+ return -EINVAL; -+ } -+ -+ vreg->speed_bin_fuse = fuse->speed_bin; -+ vreg->cpr_rev_fuse = fuse->cpr_fusing_rev; -+ vreg->fuse_corner_count = g_valid_fuse_count; -+ vreg->platform_fuses = fuse; -+ -+ return 0; -+} -+ -+/** -+ * cpr4_apss_parse_corner_data() - parse APSS corner data from device tree -+ * properties of the CPR3 regulator's device node -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr4_apss_parse_corner_data(struct cpr3_regulator *vreg) -+{ -+ struct device_node *node = vreg->of_node; -+ struct cpr4_ipq807x_apss_fuses *fuse = vreg->platform_fuses; -+ u32 *temp = NULL; -+ int i, rc; -+ -+ rc = cpr3_parse_common_corner_data(vreg); -+ if (rc) { -+ cpr3_err(vreg, "error reading corner data, rc=%d\n", rc); -+ return rc; -+ } -+ -+ /* If fuse has incorrect RO Select values and dtsi has "qcom,cpr-ro-sel" -+ * entry with RO select values other than zero, then dtsi values will -+ * be used. -+ */ -+ if (of_find_property(node, "qcom,cpr-ro-sel", NULL)) { -+ temp = kcalloc(vreg->fuse_corner_count, sizeof(*temp), -+ GFP_KERNEL); -+ if (!temp) -+ return -ENOMEM; -+ -+ rc = cpr3_parse_array_property(vreg, "qcom,cpr-ro-sel", -+ vreg->fuse_corner_count, temp); -+ if (rc) -+ goto done; -+ -+ for (i = 0; i < vreg->fuse_corner_count; i++) { -+ if (temp[i] != 0) -+ fuse->ro_sel[i] = temp[i]; -+ } -+ } -+done: -+ kfree(temp); -+ return rc; -+} -+ -+/** -+ * cpr4_apss_parse_misc_fuse_voltage_adjustments() - fill an array from a -+ * portion of the voltage adjustments specified based on -+ * miscellaneous fuse bits. -+ * @vreg: Pointer to the CPR3 regulator -+ * @volt_adjust: Voltage adjustment output data array which must be -+ * of size vreg->corner_count -+ * -+ * cpr3_parse_common_corner_data() must be called for vreg before this function -+ * is called so that speed bin size elements are initialized. -+ * -+ * Two formats are supported for the device tree property: -+ * 1. Length == tuple_list_size * vreg->corner_count -+ * (reading begins at index 0) -+ * 2. Length == tuple_list_size * vreg->speed_bin_corner_sum -+ * (reading begins at index tuple_list_size * vreg->speed_bin_offset) -+ * -+ * Here, tuple_list_size is the number of possible values for misc fuse. -+ * All other property lengths are treated as errors. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr4_apss_parse_misc_fuse_voltage_adjustments( -+ struct cpr3_regulator *vreg, u32 *volt_adjust) -+{ -+ struct device_node *node = vreg->of_node; -+ struct cpr4_ipq807x_apss_fuses *fuse = vreg->platform_fuses; -+ int tuple_list_size = IPQ807x_MISC_FUSE_VAL_COUNT; -+ int i, offset, rc, len = 0; -+ const char *prop_name = "qcom,cpr-misc-fuse-voltage-adjustment"; -+ -+ if (!of_find_property(node, prop_name, &len)) { -+ cpr3_err(vreg, "property %s is missing\n", prop_name); -+ return -EINVAL; -+ } -+ -+ if (len == tuple_list_size * vreg->corner_count * sizeof(u32)) { -+ offset = 0; -+ } else if (vreg->speed_bin_corner_sum > 0 && -+ len == tuple_list_size * vreg->speed_bin_corner_sum -+ * sizeof(u32)) { -+ offset = tuple_list_size * vreg->speed_bin_offset -+ + fuse->misc * vreg->corner_count; -+ } else { -+ if (vreg->speed_bin_corner_sum > 0) -+ cpr3_err(vreg, "property %s has invalid length=%d, should be %zu or %zu\n", -+ prop_name, len, -+ tuple_list_size * vreg->corner_count -+ * sizeof(u32), -+ tuple_list_size * vreg->speed_bin_corner_sum -+ * sizeof(u32)); -+ else -+ cpr3_err(vreg, "property %s has invalid length=%d, should be %zu\n", -+ prop_name, len, -+ tuple_list_size * vreg->corner_count -+ * sizeof(u32)); -+ return -EINVAL; -+ } -+ -+ for (i = 0; i < vreg->corner_count; i++) { -+ rc = of_property_read_u32_index(node, prop_name, offset + i, -+ &volt_adjust[i]); -+ if (rc) { -+ cpr3_err(vreg, "error reading property %s, rc=%d\n", -+ prop_name, rc); -+ return rc; -+ } -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr4_ipq807x_apss_calculate_open_loop_voltages() - calculate the open-loop -+ * voltage for each corner of a CPR3 regulator -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * If open-loop voltage interpolation is allowed in device tree, then -+ * this function calculates the open-loop voltage for a given corner using -+ * linear interpolation. This interpolation is performed using the processor -+ * frequencies of the lower and higher Fmax corners along with their fused -+ * open-loop voltages. -+ * -+ * If open-loop voltage interpolation is not allowed, then this function uses -+ * the Fmax fused open-loop voltage for all of the corners associated with a -+ * given fuse corner. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr4_ipq807x_apss_calculate_open_loop_voltages( -+ struct cpr3_regulator *vreg) -+{ -+ struct device_node *node = vreg->of_node; -+ struct cpr4_ipq807x_apss_fuses *fuse = vreg->platform_fuses; -+ struct cpr3_controller *ctrl = vreg->thread->ctrl; -+ int i, j, rc = 0; -+ bool allow_interpolation; -+ u64 freq_low, volt_low, freq_high, volt_high; -+ int *fuse_volt, *misc_adj_volt; -+ int *fmax_corner; -+ -+ fuse_volt = kcalloc(vreg->fuse_corner_count, sizeof(*fuse_volt), -+ GFP_KERNEL); -+ fmax_corner = kcalloc(vreg->fuse_corner_count, sizeof(*fmax_corner), -+ GFP_KERNEL); -+ if (!fuse_volt || !fmax_corner) { -+ rc = -ENOMEM; -+ goto done; -+ } -+ -+ for (i = 0; i < vreg->fuse_corner_count; i++) { -+ if (ctrl->cpr_global_setting == CPR_DISABLED) -+ fuse_volt[i] = vreg->cpr4_regulator_data->fuse_ref_volt[i]; -+ else -+ fuse_volt[i] = cpr3_convert_open_loop_voltage_fuse( -+ vreg->cpr4_regulator_data->fuse_ref_volt[i], -+ vreg->cpr4_regulator_data->fuse_step_volt, -+ fuse->init_voltage[i], -+ IPQ807x_APSS_VOLTAGE_FUSE_SIZE); -+ -+ /* Log fused open-loop voltage values for debugging purposes. */ -+ cpr3_info(vreg, "fused %8s: open-loop=%7d uV\n", -+ cpr4_ipq807x_apss_fuse_corner_name[i], -+ fuse_volt[i]); -+ } -+ -+ rc = cpr3_determine_part_type(vreg, -+ fuse_volt[vreg->fuse_corner_count - 1]); -+ if (rc) { -+ cpr3_err(vreg, "fused part type detection failed failed, rc=%d\n", -+ rc); -+ goto done; -+ } -+ -+ rc = cpr3_adjust_fused_open_loop_voltages(vreg, fuse_volt); -+ if (rc) { -+ cpr3_err(vreg, "fused open-loop voltage adjustment failed, rc=%d\n", -+ rc); -+ goto done; -+ } -+ -+ allow_interpolation = of_property_read_bool(node, -+ "qcom,allow-voltage-interpolation"); -+ -+ for (i = 1; i < vreg->fuse_corner_count; i++) { -+ if (fuse_volt[i] < fuse_volt[i - 1]) { -+ cpr3_info(vreg, "fuse corner %d voltage=%d uV < fuse corner %d voltage=%d uV; overriding: fuse corner %d voltage=%d\n", -+ i, fuse_volt[i], i - 1, fuse_volt[i - 1], -+ i, fuse_volt[i - 1]); -+ fuse_volt[i] = fuse_volt[i - 1]; -+ } -+ } -+ -+ if (!allow_interpolation) { -+ /* Use fused open-loop voltage for lower frequencies. */ -+ for (i = 0; i < vreg->corner_count; i++) -+ vreg->corner[i].open_loop_volt -+ = fuse_volt[vreg->corner[i].cpr_fuse_corner]; -+ goto done; -+ } -+ -+ /* Determine highest corner mapped to each fuse corner */ -+ j = vreg->fuse_corner_count - 1; -+ for (i = vreg->corner_count - 1; i >= 0; i--) { -+ if (vreg->corner[i].cpr_fuse_corner == j) { -+ fmax_corner[j] = i; -+ j--; -+ } -+ } -+ if (j >= 0) { -+ cpr3_err(vreg, "invalid fuse corner mapping\n"); -+ rc = -EINVAL; -+ goto done; -+ } -+ -+ /* -+ * Interpolation is not possible for corners mapped to the lowest fuse -+ * corner so use the fuse corner value directly. -+ */ -+ for (i = 0; i <= fmax_corner[0]; i++) -+ vreg->corner[i].open_loop_volt = fuse_volt[0]; -+ -+ /* Interpolate voltages for the higher fuse corners. */ -+ for (i = 1; i < vreg->fuse_corner_count; i++) { -+ freq_low = vreg->corner[fmax_corner[i - 1]].proc_freq; -+ volt_low = fuse_volt[i - 1]; -+ freq_high = vreg->corner[fmax_corner[i]].proc_freq; -+ volt_high = fuse_volt[i]; -+ -+ for (j = fmax_corner[i - 1] + 1; j <= fmax_corner[i]; j++) -+ vreg->corner[j].open_loop_volt = cpr3_interpolate( -+ freq_low, volt_low, freq_high, volt_high, -+ vreg->corner[j].proc_freq); -+ } -+ -+done: -+ if (rc == 0) { -+ cpr3_debug(vreg, "unadjusted per-corner open-loop voltages:\n"); -+ for (i = 0; i < vreg->corner_count; i++) -+ cpr3_debug(vreg, "open-loop[%2d] = %d uV\n", i, -+ vreg->corner[i].open_loop_volt); -+ -+ rc = cpr3_adjust_open_loop_voltages(vreg); -+ if (rc) -+ cpr3_err(vreg, "open-loop voltage adjustment failed, rc=%d\n", -+ rc); -+ -+ if (of_find_property(node, -+ "qcom,cpr-misc-fuse-voltage-adjustment", -+ NULL)) { -+ misc_adj_volt = kcalloc(vreg->corner_count, -+ sizeof(*misc_adj_volt), GFP_KERNEL); -+ if (!misc_adj_volt) { -+ rc = -ENOMEM; -+ goto _exit; -+ } -+ -+ rc = cpr4_apss_parse_misc_fuse_voltage_adjustments(vreg, -+ misc_adj_volt); -+ if (rc) { -+ cpr3_err(vreg, "qcom,cpr-misc-fuse-voltage-adjustment reading failed, rc=%d\n", -+ rc); -+ kfree(misc_adj_volt); -+ goto _exit; -+ } -+ -+ for (i = 0; i < vreg->corner_count; i++) -+ vreg->corner[i].open_loop_volt -+ += misc_adj_volt[i]; -+ kfree(misc_adj_volt); -+ } -+ } -+ -+_exit: -+ kfree(fuse_volt); -+ kfree(fmax_corner); -+ return rc; -+} -+ -+/** -+ * cpr4_ipq807x_apss_set_no_interpolation_quotients() - use the fused target -+ * quotient values for lower frequencies. -+ * @vreg: Pointer to the CPR3 regulator -+ * @volt_adjust: Pointer to array of per-corner closed-loop adjustment -+ * voltages -+ * @volt_adjust_fuse: Pointer to array of per-fuse-corner closed-loop -+ * adjustment voltages -+ * @ro_scale: Pointer to array of per-fuse-corner RO scaling factor -+ * values with units of QUOT/V -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr4_ipq807x_apss_set_no_interpolation_quotients( -+ struct cpr3_regulator *vreg, int *volt_adjust, -+ int *volt_adjust_fuse, int *ro_scale) -+{ -+ struct cpr4_ipq807x_apss_fuses *fuse = vreg->platform_fuses; -+ u32 quot, ro; -+ int quot_adjust; -+ int i, fuse_corner; -+ -+ for (i = 0; i < vreg->corner_count; i++) { -+ fuse_corner = vreg->corner[i].cpr_fuse_corner; -+ quot = fuse->target_quot[fuse_corner]; -+ quot_adjust = cpr3_quot_adjustment(ro_scale[fuse_corner], -+ volt_adjust_fuse[fuse_corner] + -+ volt_adjust[i]); -+ ro = fuse->ro_sel[fuse_corner]; -+ vreg->corner[i].target_quot[ro] = quot + quot_adjust; -+ cpr3_debug(vreg, "corner=%d RO=%u target quot=%u\n", -+ i, ro, quot); -+ -+ if (quot_adjust) -+ cpr3_debug(vreg, "adjusted corner %d RO%u target quot: %u --> %u (%d uV)\n", -+ i, ro, quot, vreg->corner[i].target_quot[ro], -+ volt_adjust_fuse[fuse_corner] + -+ volt_adjust[i]); -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr4_ipq807x_apss_calculate_target_quotients() - calculate the CPR target -+ * quotient for each corner of a CPR3 regulator -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * If target quotient interpolation is allowed in device tree, then this -+ * function calculates the target quotient for a given corner using linear -+ * interpolation. This interpolation is performed using the processor -+ * frequencies of the lower and higher Fmax corners along with the fused -+ * target quotient and quotient offset of the higher Fmax corner. -+ * -+ * If target quotient interpolation is not allowed, then this function uses -+ * the Fmax fused target quotient for all of the corners associated with a -+ * given fuse corner. -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr4_ipq807x_apss_calculate_target_quotients( -+ struct cpr3_regulator *vreg) -+{ -+ struct cpr4_ipq807x_apss_fuses *fuse = vreg->platform_fuses; -+ int rc; -+ bool allow_interpolation; -+ u64 freq_low, freq_high, prev_quot; -+ u64 *quot_low; -+ u64 *quot_high; -+ u32 quot, ro; -+ int i, j, fuse_corner, quot_adjust; -+ int *fmax_corner; -+ int *volt_adjust, *volt_adjust_fuse, *ro_scale; -+ int *voltage_adj_misc; -+ -+ /* Log fused quotient values for debugging purposes. */ -+ for (i = CPR4_IPQ807x_APSS_FUSE_CORNER_SVS; -+ i < vreg->fuse_corner_count; i++) -+ cpr3_info(vreg, "fused %8s: quot[%2llu]=%4llu, quot_offset[%2llu]=%4llu\n", -+ cpr4_ipq807x_apss_fuse_corner_name[i], -+ fuse->ro_sel[i], fuse->target_quot[i], -+ fuse->ro_sel[i], fuse->quot_offset[i] * -+ IPQ807x_APSS_QUOT_OFFSET_SCALE); -+ -+ allow_interpolation = of_property_read_bool(vreg->of_node, -+ "qcom,allow-quotient-interpolation"); -+ -+ volt_adjust = kcalloc(vreg->corner_count, sizeof(*volt_adjust), -+ GFP_KERNEL); -+ volt_adjust_fuse = kcalloc(vreg->fuse_corner_count, -+ sizeof(*volt_adjust_fuse), GFP_KERNEL); -+ ro_scale = kcalloc(vreg->fuse_corner_count, sizeof(*ro_scale), -+ GFP_KERNEL); -+ fmax_corner = kcalloc(vreg->fuse_corner_count, sizeof(*fmax_corner), -+ GFP_KERNEL); -+ quot_low = kcalloc(vreg->fuse_corner_count, sizeof(*quot_low), -+ GFP_KERNEL); -+ quot_high = kcalloc(vreg->fuse_corner_count, sizeof(*quot_high), -+ GFP_KERNEL); -+ if (!volt_adjust || !volt_adjust_fuse || !ro_scale || -+ !fmax_corner || !quot_low || !quot_high) { -+ rc = -ENOMEM; -+ goto done; -+ } -+ -+ rc = cpr3_parse_closed_loop_voltage_adjustments(vreg, &fuse->ro_sel[0], -+ volt_adjust, volt_adjust_fuse, ro_scale); -+ if (rc) { -+ cpr3_err(vreg, "could not load closed-loop voltage adjustments, rc=%d\n", -+ rc); -+ goto done; -+ } -+ -+ if (of_find_property(vreg->of_node, -+ "qcom,cpr-misc-fuse-voltage-adjustment", NULL)) { -+ voltage_adj_misc = kcalloc(vreg->corner_count, -+ sizeof(*voltage_adj_misc), GFP_KERNEL); -+ if (!voltage_adj_misc) { -+ rc = -ENOMEM; -+ goto done; -+ } -+ -+ rc = cpr4_apss_parse_misc_fuse_voltage_adjustments(vreg, -+ voltage_adj_misc); -+ if (rc) { -+ cpr3_err(vreg, "qcom,cpr-misc-fuse-voltage-adjustment reading failed, rc=%d\n", -+ rc); -+ kfree(voltage_adj_misc); -+ goto done; -+ } -+ -+ for (i = 0; i < vreg->corner_count; i++) -+ volt_adjust[i] += voltage_adj_misc[i]; -+ -+ kfree(voltage_adj_misc); -+ } -+ -+ if (!allow_interpolation) { -+ /* Use fused target quotients for lower frequencies. */ -+ return cpr4_ipq807x_apss_set_no_interpolation_quotients( -+ vreg, volt_adjust, volt_adjust_fuse, ro_scale); -+ } -+ -+ /* Determine highest corner mapped to each fuse corner */ -+ j = vreg->fuse_corner_count - 1; -+ for (i = vreg->corner_count - 1; i >= 0; i--) { -+ if (vreg->corner[i].cpr_fuse_corner == j) { -+ fmax_corner[j] = i; -+ j--; -+ } -+ } -+ if (j >= 0) { -+ cpr3_err(vreg, "invalid fuse corner mapping\n"); -+ rc = -EINVAL; -+ goto done; -+ } -+ -+ /* -+ * Interpolation is not possible for corners mapped to the lowest fuse -+ * corner so use the fuse corner value directly. -+ */ -+ i = CPR4_IPQ807x_APSS_FUSE_CORNER_SVS; -+ quot_adjust = cpr3_quot_adjustment(ro_scale[i], volt_adjust_fuse[i]); -+ quot = fuse->target_quot[i] + quot_adjust; -+ quot_high[i] = quot_low[i] = quot; -+ ro = fuse->ro_sel[i]; -+ if (quot_adjust) -+ cpr3_debug(vreg, "adjusted fuse corner %d RO%u target quot: %llu --> %u (%d uV)\n", -+ i, ro, fuse->target_quot[i], quot, volt_adjust_fuse[i]); -+ -+ for (i = 0; i <= fmax_corner[CPR4_IPQ807x_APSS_FUSE_CORNER_SVS]; -+ i++) -+ vreg->corner[i].target_quot[ro] = quot; -+ -+ for (i = CPR4_IPQ807x_APSS_FUSE_CORNER_NOM; -+ i < vreg->fuse_corner_count; i++) { -+ quot_high[i] = fuse->target_quot[i]; -+ if (fuse->ro_sel[i] == fuse->ro_sel[i - 1]) -+ quot_low[i] = quot_high[i - 1]; -+ else -+ quot_low[i] = quot_high[i] -+ - fuse->quot_offset[i] -+ * IPQ807x_APSS_QUOT_OFFSET_SCALE; -+ if (quot_high[i] < quot_low[i]) { -+ cpr3_debug(vreg, "quot_high[%d]=%llu < quot_low[%d]=%llu; overriding: quot_high[%d]=%llu\n", -+ i, quot_high[i], i, quot_low[i], -+ i, quot_low[i]); -+ quot_high[i] = quot_low[i]; -+ } -+ } -+ -+ /* Perform per-fuse-corner target quotient adjustment */ -+ for (i = 1; i < vreg->fuse_corner_count; i++) { -+ quot_adjust = cpr3_quot_adjustment(ro_scale[i], -+ volt_adjust_fuse[i]); -+ if (quot_adjust) { -+ prev_quot = quot_high[i]; -+ quot_high[i] += quot_adjust; -+ cpr3_debug(vreg, "adjusted fuse corner %d RO%llu target quot: %llu --> %llu (%d uV)\n", -+ i, fuse->ro_sel[i], prev_quot, quot_high[i], -+ volt_adjust_fuse[i]); -+ } -+ -+ if (fuse->ro_sel[i] == fuse->ro_sel[i - 1]) -+ quot_low[i] = quot_high[i - 1]; -+ else -+ quot_low[i] += cpr3_quot_adjustment(ro_scale[i], -+ volt_adjust_fuse[i - 1]); -+ -+ if (quot_high[i] < quot_low[i]) { -+ cpr3_debug(vreg, "quot_high[%d]=%llu < quot_low[%d]=%llu after adjustment; overriding: quot_high[%d]=%llu\n", -+ i, quot_high[i], i, quot_low[i], -+ i, quot_low[i]); -+ quot_high[i] = quot_low[i]; -+ } -+ } -+ -+ /* Interpolate voltages for the higher fuse corners. */ -+ for (i = 1; i < vreg->fuse_corner_count; i++) { -+ freq_low = vreg->corner[fmax_corner[i - 1]].proc_freq; -+ freq_high = vreg->corner[fmax_corner[i]].proc_freq; -+ -+ ro = fuse->ro_sel[i]; -+ for (j = fmax_corner[i - 1] + 1; j <= fmax_corner[i]; j++) -+ vreg->corner[j].target_quot[ro] = cpr3_interpolate( -+ freq_low, quot_low[i], freq_high, quot_high[i], -+ vreg->corner[j].proc_freq); -+ } -+ -+ /* Perform per-corner target quotient adjustment */ -+ for (i = 0; i < vreg->corner_count; i++) { -+ fuse_corner = vreg->corner[i].cpr_fuse_corner; -+ ro = fuse->ro_sel[fuse_corner]; -+ quot_adjust = cpr3_quot_adjustment(ro_scale[fuse_corner], -+ volt_adjust[i]); -+ if (quot_adjust) { -+ prev_quot = vreg->corner[i].target_quot[ro]; -+ vreg->corner[i].target_quot[ro] += quot_adjust; -+ cpr3_debug(vreg, "adjusted corner %d RO%u target quot: %llu --> %u (%d uV)\n", -+ i, ro, prev_quot, -+ vreg->corner[i].target_quot[ro], -+ volt_adjust[i]); -+ } -+ } -+ -+ /* Ensure that target quotients increase monotonically */ -+ for (i = 1; i < vreg->corner_count; i++) { -+ ro = fuse->ro_sel[vreg->corner[i].cpr_fuse_corner]; -+ if (fuse->ro_sel[vreg->corner[i - 1].cpr_fuse_corner] == ro -+ && vreg->corner[i].target_quot[ro] -+ < vreg->corner[i - 1].target_quot[ro]) { -+ cpr3_debug(vreg, "adjusted corner %d RO%u target quot=%u < adjusted corner %d RO%u target quot=%u; overriding: corner %d RO%u target quot=%u\n", -+ i, ro, vreg->corner[i].target_quot[ro], -+ i - 1, ro, vreg->corner[i - 1].target_quot[ro], -+ i, ro, vreg->corner[i - 1].target_quot[ro]); -+ vreg->corner[i].target_quot[ro] -+ = vreg->corner[i - 1].target_quot[ro]; -+ } -+ } -+ -+done: -+ kfree(volt_adjust); -+ kfree(volt_adjust_fuse); -+ kfree(ro_scale); -+ kfree(fmax_corner); -+ kfree(quot_low); -+ kfree(quot_high); -+ return rc; -+} -+ -+/** -+ * cpr4_apss_print_settings() - print out APSS CPR configuration settings into -+ * the kernel log for debugging purposes -+ * @vreg: Pointer to the CPR3 regulator -+ */ -+static void cpr4_apss_print_settings(struct cpr3_regulator *vreg) -+{ -+ struct cpr3_corner *corner; -+ int i; -+ -+ cpr3_debug(vreg, "Corner: Frequency (Hz), Fuse Corner, Floor (uV), Open-Loop (uV), Ceiling (uV)\n"); -+ for (i = 0; i < vreg->corner_count; i++) { -+ corner = &vreg->corner[i]; -+ cpr3_debug(vreg, "%3d: %10u, %2d, %7d, %7d, %7d\n", -+ i, corner->proc_freq, corner->cpr_fuse_corner, -+ corner->floor_volt, corner->open_loop_volt, -+ corner->ceiling_volt); -+ } -+ -+ if (vreg->thread->ctrl->apm) -+ cpr3_debug(vreg, "APM threshold = %d uV, APM adjust = %d uV\n", -+ vreg->thread->ctrl->apm_threshold_volt, -+ vreg->thread->ctrl->apm_adj_volt); -+} -+ -+/** -+ * cpr4_apss_init_thread() - perform steps necessary to initialize the -+ * configuration data for a CPR3 thread -+ * @thread: Pointer to the CPR3 thread -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr4_apss_init_thread(struct cpr3_thread *thread) -+{ -+ int rc; -+ -+ rc = cpr3_parse_common_thread_data(thread); -+ if (rc) { -+ cpr3_err(thread->ctrl, "thread %u unable to read CPR thread data from device tree, rc=%d\n", -+ thread->thread_id, rc); -+ return rc; -+ } -+ -+ return 0; -+} -+ -+/** -+ * cpr4_apss_parse_temp_adj_properties() - parse temperature based -+ * adjustment properties from device tree. -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr4_apss_parse_temp_adj_properties(struct cpr3_controller *ctrl) -+{ -+ struct device_node *of_node = ctrl->dev->of_node; -+ int rc, i, len, temp_point_count; -+ -+ if (!of_find_property(of_node, "qcom,cpr-temp-point-map", &len)) { -+ /* -+ * Temperature based adjustments are not defined. Single -+ * temperature band is still valid for per-online-core -+ * adjustments. -+ */ -+ ctrl->temp_band_count = 1; -+ return 0; -+ } -+ -+ temp_point_count = len / sizeof(u32); -+ if (temp_point_count <= 0 || -+ temp_point_count > IPQ807x_APSS_MAX_TEMP_POINTS) { -+ cpr3_err(ctrl, "invalid number of temperature points %d > %d (max)\n", -+ temp_point_count, IPQ807x_APSS_MAX_TEMP_POINTS); -+ return -EINVAL; -+ } -+ -+ ctrl->temp_points = devm_kcalloc(ctrl->dev, temp_point_count, -+ sizeof(*ctrl->temp_points), GFP_KERNEL); -+ if (!ctrl->temp_points) -+ return -ENOMEM; -+ -+ rc = of_property_read_u32_array(of_node, "qcom,cpr-temp-point-map", -+ ctrl->temp_points, temp_point_count); -+ if (rc) { -+ cpr3_err(ctrl, "error reading property qcom,cpr-temp-point-map, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ for (i = 0; i < temp_point_count; i++) -+ cpr3_debug(ctrl, "Temperature Point %d=%d\n", i, -+ ctrl->temp_points[i]); -+ -+ /* -+ * If t1, t2, and t3 are the temperature points, then the temperature -+ * bands are: (-inf, t1], (t1, t2], (t2, t3], and (t3, inf). -+ */ -+ ctrl->temp_band_count = temp_point_count + 1; -+ cpr3_debug(ctrl, "Number of temp bands =%d\n", ctrl->temp_band_count); -+ -+ rc = of_property_read_u32(of_node, "qcom,cpr-initial-temp-band", -+ &ctrl->initial_temp_band); -+ if (rc) { -+ cpr3_err(ctrl, "error reading qcom,cpr-initial-temp-band, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ if (ctrl->initial_temp_band >= ctrl->temp_band_count) { -+ cpr3_err(ctrl, "Initial temperature band value %d should be in range [0 - %d]\n", -+ ctrl->initial_temp_band, ctrl->temp_band_count - 1); -+ return -EINVAL; -+ } -+ -+ ctrl->temp_sensor_id_start = IPQ807x_APSS_TEMP_SENSOR_ID_START; -+ ctrl->temp_sensor_id_end = IPQ807x_APSS_TEMP_SENSOR_ID_END; -+ ctrl->allow_temp_adj = true; -+ return rc; -+} -+ -+/** -+ * cpr4_apss_parse_boost_properties() - parse configuration data for boost -+ * voltage adjustment for CPR3 regulator from device tree. -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr4_apss_parse_boost_properties(struct cpr3_regulator *vreg) -+{ -+ struct cpr3_controller *ctrl = vreg->thread->ctrl; -+ struct cpr4_ipq807x_apss_fuses *fuse = vreg->platform_fuses; -+ struct cpr3_corner *corner; -+ int i, boost_voltage, final_boost_volt, rc = 0; -+ int *boost_table = NULL, *boost_temp_adj = NULL; -+ int boost_voltage_adjust = 0, boost_num_cores = 0; -+ u32 boost_allowed = 0; -+ -+ if (!boost_fuse[fuse->boost_cfg]) -+ /* Voltage boost is disabled in fuse */ -+ return 0; -+ -+ if (of_find_property(vreg->of_node, "qcom,allow-boost", NULL)) { -+ rc = cpr3_parse_array_property(vreg, "qcom,allow-boost", 1, -+ &boost_allowed); -+ if (rc) -+ return rc; -+ } -+ -+ if (!boost_allowed) { -+ /* Voltage boost is not enabled for this regulator */ -+ return 0; -+ } -+ -+ boost_voltage = cpr3_convert_open_loop_voltage_fuse( -+ vreg->cpr4_regulator_data->boost_fuse_ref_volt, -+ vreg->cpr4_regulator_data->fuse_step_volt, -+ fuse->boost_voltage, -+ IPQ807x_APSS_VOLTAGE_FUSE_SIZE); -+ -+ /* Log boost voltage value for debugging purposes. */ -+ cpr3_info(vreg, "Boost open-loop=%7d uV\n", boost_voltage); -+ -+ if (of_find_property(vreg->of_node, -+ "qcom,cpr-boost-voltage-fuse-adjustment", NULL)) { -+ rc = cpr3_parse_array_property(vreg, -+ "qcom,cpr-boost-voltage-fuse-adjustment", -+ 1, &boost_voltage_adjust); -+ if (rc) { -+ cpr3_err(vreg, "qcom,cpr-boost-voltage-fuse-adjustment reading failed, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ boost_voltage += boost_voltage_adjust; -+ /* Log boost voltage value for debugging purposes. */ -+ cpr3_info(vreg, "Adjusted boost open-loop=%7d uV\n", -+ boost_voltage); -+ } -+ -+ /* Limit boost voltage value between ceiling and floor voltage limits */ -+ boost_voltage = min(boost_voltage, vreg->cpr4_regulator_data->boost_ceiling_volt); -+ boost_voltage = max(boost_voltage, vreg->cpr4_regulator_data->boost_floor_volt); -+ -+ /* -+ * The boost feature can only be used for the highest voltage corner. -+ * Also, keep core-count adjustments disabled when the boost feature -+ * is enabled. -+ */ -+ corner = &vreg->corner[vreg->corner_count - 1]; -+ if (!corner->sdelta) { -+ /* -+ * If core-count/temp adjustments are not defined, the cpr4 -+ * sdelta for this corner will not be allocated. Allocate it -+ * here for boost configuration. -+ */ -+ corner->sdelta = devm_kzalloc(ctrl->dev, -+ sizeof(*corner->sdelta), GFP_KERNEL); -+ if (!corner->sdelta) -+ return -ENOMEM; -+ } -+ corner->sdelta->temp_band_count = ctrl->temp_band_count; -+ -+ rc = of_property_read_u32(vreg->of_node, "qcom,cpr-num-boost-cores", -+ &boost_num_cores); -+ if (rc) { -+ cpr3_err(vreg, "qcom,cpr-num-boost-cores reading failed, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ if (boost_num_cores <= 0 || -+ boost_num_cores > IPQ807x_APSS_CPR_SDELTA_CORE_COUNT) { -+ cpr3_err(vreg, "Invalid boost number of cores = %d\n", -+ boost_num_cores); -+ return -EINVAL; -+ } -+ corner->sdelta->boost_num_cores = boost_num_cores; -+ -+ boost_table = devm_kcalloc(ctrl->dev, corner->sdelta->temp_band_count, -+ sizeof(*boost_table), GFP_KERNEL); -+ if (!boost_table) -+ return -ENOMEM; -+ -+ if (of_find_property(vreg->of_node, -+ "qcom,cpr-boost-temp-adjustment", NULL)) { -+ boost_temp_adj = kcalloc(corner->sdelta->temp_band_count, -+ sizeof(*boost_temp_adj), GFP_KERNEL); -+ if (!boost_temp_adj) -+ return -ENOMEM; -+ -+ rc = cpr3_parse_array_property(vreg, -+ "qcom,cpr-boost-temp-adjustment", -+ corner->sdelta->temp_band_count, -+ boost_temp_adj); -+ if (rc) { -+ cpr3_err(vreg, "qcom,cpr-boost-temp-adjustment reading failed, rc=%d\n", -+ rc); -+ goto done; -+ } -+ } -+ -+ for (i = 0; i < corner->sdelta->temp_band_count; i++) { -+ /* Apply static adjustments to boost voltage */ -+ final_boost_volt = boost_voltage + (boost_temp_adj == NULL -+ ? 0 : boost_temp_adj[i]); -+ /* -+ * Limit final adjusted boost voltage value between ceiling -+ * and floor voltage limits -+ */ -+ final_boost_volt = min(final_boost_volt, -+ vreg->cpr4_regulator_data->boost_ceiling_volt); -+ final_boost_volt = max(final_boost_volt, -+ vreg->cpr4_regulator_data->boost_floor_volt); -+ -+ boost_table[i] = (corner->open_loop_volt - final_boost_volt) -+ / ctrl->step_volt; -+ cpr3_debug(vreg, "Adjusted boost voltage margin for temp band %d = %d steps\n", -+ i, boost_table[i]); -+ } -+ -+ corner->ceiling_volt = vreg->cpr4_regulator_data->boost_ceiling_volt; -+ corner->sdelta->boost_table = boost_table; -+ corner->sdelta->allow_boost = true; -+ corner->sdelta->allow_core_count_adj = false; -+ vreg->allow_boost = true; -+ ctrl->allow_boost = true; -+done: -+ kfree(boost_temp_adj); -+ return rc; -+} -+ -+/** -+ * cpr4_apss_init_regulator() - perform all steps necessary to initialize the -+ * configuration data for a CPR3 regulator -+ * @vreg: Pointer to the CPR3 regulator -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr4_apss_init_regulator(struct cpr3_regulator *vreg) -+{ -+ struct cpr4_ipq807x_apss_fuses *fuse; -+ int rc; -+ -+ rc = cpr4_ipq807x_apss_read_fuse_data(vreg); -+ if (rc) { -+ cpr3_err(vreg, "unable to read CPR fuse data, rc=%d\n", rc); -+ return rc; -+ } -+ -+ fuse = vreg->platform_fuses; -+ -+ rc = cpr4_apss_parse_corner_data(vreg); -+ if (rc) { -+ cpr3_err(vreg, "unable to read CPR corner data from device tree, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ rc = cpr3_mem_acc_init(vreg); -+ if (rc) { -+ if (rc != -EPROBE_DEFER) -+ cpr3_err(vreg, "unable to initialize mem-acc regulator settings, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ rc = cpr4_ipq807x_apss_calculate_open_loop_voltages(vreg); -+ if (rc) { -+ cpr3_err(vreg, "unable to calculate open-loop voltages, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ rc = cpr3_limit_open_loop_voltages(vreg); -+ if (rc) { -+ cpr3_err(vreg, "unable to limit open-loop voltages, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ cpr3_open_loop_voltage_as_ceiling(vreg); -+ -+ rc = cpr3_limit_floor_voltages(vreg); -+ if (rc) { -+ cpr3_err(vreg, "unable to limit floor voltages, rc=%d\n", rc); -+ return rc; -+ } -+ -+ rc = cpr4_ipq807x_apss_calculate_target_quotients(vreg); -+ if (rc) { -+ cpr3_err(vreg, "unable to calculate target quotients, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ rc = cpr4_parse_core_count_temp_voltage_adj(vreg, false); -+ if (rc) { -+ cpr3_err(vreg, "unable to parse temperature and core count voltage adjustments, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ if (vreg->allow_core_count_adj && (vreg->max_core_count <= 0 -+ || vreg->max_core_count > -+ IPQ807x_APSS_CPR_SDELTA_CORE_COUNT)) { -+ cpr3_err(vreg, "qcom,max-core-count has invalid value = %d\n", -+ vreg->max_core_count); -+ return -EINVAL; -+ } -+ -+ rc = cpr4_apss_parse_boost_properties(vreg); -+ if (rc) { -+ cpr3_err(vreg, "unable to parse boost adjustments, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ cpr4_apss_print_settings(vreg); -+ -+ return rc; -+} -+ -+/** -+ * cpr4_apss_init_controller() - perform APSS CPR4 controller specific -+ * initializations -+ * @ctrl: Pointer to the CPR3 controller -+ * -+ * Return: 0 on success, errno on failure -+ */ -+static int cpr4_apss_init_controller(struct cpr3_controller *ctrl) -+{ -+ int rc; -+ -+ rc = cpr3_parse_common_ctrl_data(ctrl); -+ if (rc) { -+ if (rc != -EPROBE_DEFER) -+ cpr3_err(ctrl, "unable to parse common controller data, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ rc = of_property_read_u32(ctrl->dev->of_node, -+ "qcom,cpr-down-error-step-limit", -+ &ctrl->down_error_step_limit); -+ if (rc) { -+ cpr3_err(ctrl, "error reading qcom,cpr-down-error-step-limit, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ rc = of_property_read_u32(ctrl->dev->of_node, -+ "qcom,cpr-up-error-step-limit", -+ &ctrl->up_error_step_limit); -+ if (rc) { -+ cpr3_err(ctrl, "error reading qcom,cpr-up-error-step-limit, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ /* -+ * Use fixed step quotient if specified otherwise use dynamic -+ * calculated per RO step quotient -+ */ -+ of_property_read_u32(ctrl->dev->of_node, "qcom,cpr-step-quot-fixed", -+ &ctrl->step_quot_fixed); -+ ctrl->use_dynamic_step_quot = ctrl->step_quot_fixed ? false : true; -+ -+ ctrl->saw_use_unit_mV = of_property_read_bool(ctrl->dev->of_node, -+ "qcom,cpr-saw-use-unit-mV"); -+ -+ of_property_read_u32(ctrl->dev->of_node, -+ "qcom,cpr-voltage-settling-time", -+ &ctrl->voltage_settling_time); -+ -+ if (of_find_property(ctrl->dev->of_node, "vdd-limit-supply", NULL)) { -+ ctrl->vdd_limit_regulator = -+ devm_regulator_get(ctrl->dev, "vdd-limit"); -+ if (IS_ERR(ctrl->vdd_limit_regulator)) { -+ rc = PTR_ERR(ctrl->vdd_limit_regulator); -+ if (rc != -EPROBE_DEFER) -+ cpr3_err(ctrl, "unable to request vdd-limit regulator, rc=%d\n", -+ rc); -+ return rc; -+ } -+ } -+ -+ rc = cpr3_apm_init(ctrl); -+ if (rc) { -+ if (rc != -EPROBE_DEFER) -+ cpr3_err(ctrl, "unable to initialize APM settings, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ rc = cpr4_apss_parse_temp_adj_properties(ctrl); -+ if (rc) { -+ cpr3_err(ctrl, "unable to parse temperature adjustment properties, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ ctrl->sensor_count = IPQ807x_APSS_CPR_SENSOR_COUNT; -+ -+ /* -+ * APSS only has one thread (0) per controller so the zeroed -+ * array does not need further modification. -+ */ -+ ctrl->sensor_owner = devm_kcalloc(ctrl->dev, ctrl->sensor_count, -+ sizeof(*ctrl->sensor_owner), GFP_KERNEL); -+ if (!ctrl->sensor_owner) -+ return -ENOMEM; -+ -+ ctrl->ctrl_type = CPR_CTRL_TYPE_CPR4; -+ ctrl->supports_hw_closed_loop = false; -+ ctrl->use_hw_closed_loop = of_property_read_bool(ctrl->dev->of_node, -+ "qcom,cpr-hw-closed-loop"); -+ return 0; -+} -+ -+static int cpr4_apss_regulator_suspend(struct platform_device *pdev, -+ pm_message_t state) -+{ -+ struct cpr3_controller *ctrl = platform_get_drvdata(pdev); -+ -+ return cpr3_regulator_suspend(ctrl); -+} -+ -+static int cpr4_apss_regulator_resume(struct platform_device *pdev) -+{ -+ struct cpr3_controller *ctrl = platform_get_drvdata(pdev); -+ -+ return cpr3_regulator_resume(ctrl); -+} -+ -+static void ipq6018_set_mem_acc(struct regulator_dev *rdev) -+{ -+ struct cpr3_regulator *vreg = rdev_get_drvdata(rdev); -+ -+ ipq6018_mem_acc_tcsr[0].ioremap_addr = -+ ioremap(ipq6018_mem_acc_tcsr[0].phy_addr, 0x4); -+ ipq6018_mem_acc_tcsr[1].ioremap_addr = -+ ioremap(ipq6018_mem_acc_tcsr[1].phy_addr, 0x4); -+ -+ if ((ipq6018_mem_acc_tcsr[0].ioremap_addr != NULL) && -+ (ipq6018_mem_acc_tcsr[1].ioremap_addr != NULL) && -+ (vreg->current_corner == (vreg->corner_count - CPR3_CORNER_OFFSET))) { -+ -+ writel_relaxed(ipq6018_mem_acc_tcsr[0].value, -+ ipq6018_mem_acc_tcsr[0].ioremap_addr); -+ writel_relaxed(ipq6018_mem_acc_tcsr[1].value, -+ ipq6018_mem_acc_tcsr[1].ioremap_addr); -+ } -+} -+ -+static void ipq6018_clr_mem_acc(struct regulator_dev *rdev) -+{ -+ struct cpr3_regulator *vreg = rdev_get_drvdata(rdev); -+ -+ if ((ipq6018_mem_acc_tcsr[0].ioremap_addr != NULL) && -+ (ipq6018_mem_acc_tcsr[1].ioremap_addr != NULL) && -+ (vreg->current_corner != vreg->corner_count - CPR3_CORNER_OFFSET)) { -+ writel_relaxed(0x0, ipq6018_mem_acc_tcsr[0].ioremap_addr); -+ writel_relaxed(0x0, ipq6018_mem_acc_tcsr[1].ioremap_addr); -+ } -+ -+ iounmap(ipq6018_mem_acc_tcsr[0].ioremap_addr); -+ iounmap(ipq6018_mem_acc_tcsr[1].ioremap_addr); -+} -+ -+static struct cpr4_mem_acc_func ipq6018_mem_acc_funcs = { -+ .set_mem_acc = ipq6018_set_mem_acc, -+ .clear_mem_acc = ipq6018_clr_mem_acc -+}; -+ -+static const struct cpr4_reg_data ipq807x_cpr_apss = { -+ .cpr_valid_fuse_count = IPQ807x_APSS_FUSE_CORNERS, -+ .fuse_ref_volt = ipq807x_apss_fuse_ref_volt, -+ .fuse_step_volt = IPQ807x_APSS_FUSE_STEP_VOLT, -+ .cpr_clk_rate = IPQ807x_APSS_CPR_CLOCK_RATE, -+ .boost_fuse_ref_volt= IPQ807x_APSS_BOOST_FUSE_REF_VOLT, -+ .boost_ceiling_volt= IPQ807x_APSS_BOOST_CEILING_VOLT, -+ .boost_floor_volt= IPQ807x_APSS_BOOST_FLOOR_VOLT, -+ .cpr3_fuse_params = &ipq807x_fuse_params, -+ .mem_acc_funcs = NULL, -+}; -+ -+static const struct cpr4_reg_data ipq817x_cpr_apss = { -+ .cpr_valid_fuse_count = IPQ817x_APPS_FUSE_CORNERS, -+ .fuse_ref_volt = ipq807x_apss_fuse_ref_volt, -+ .fuse_step_volt = IPQ807x_APSS_FUSE_STEP_VOLT, -+ .cpr_clk_rate = IPQ807x_APSS_CPR_CLOCK_RATE, -+ .boost_fuse_ref_volt= IPQ807x_APSS_BOOST_FUSE_REF_VOLT, -+ .boost_ceiling_volt= IPQ807x_APSS_BOOST_CEILING_VOLT, -+ .boost_floor_volt= IPQ807x_APSS_BOOST_FLOOR_VOLT, -+ .cpr3_fuse_params = &ipq807x_fuse_params, -+ .mem_acc_funcs = NULL, -+}; -+ -+static const struct cpr4_reg_data ipq6018_cpr_apss = { -+ .cpr_valid_fuse_count = IPQ6018_APSS_FUSE_CORNERS, -+ .fuse_ref_volt = ipq6018_apss_fuse_ref_volt, -+ .fuse_step_volt = IPQ6018_APSS_FUSE_STEP_VOLT, -+ .cpr_clk_rate = IPQ6018_APSS_CPR_CLOCK_RATE, -+ .boost_fuse_ref_volt = IPQ6018_APSS_BOOST_FUSE_REF_VOLT, -+ .boost_ceiling_volt = IPQ6018_APSS_BOOST_CEILING_VOLT, -+ .boost_floor_volt = IPQ6018_APSS_BOOST_FLOOR_VOLT, -+ .cpr3_fuse_params = &ipq6018_fuse_params, -+ .mem_acc_funcs = &ipq6018_mem_acc_funcs, -+}; -+ -+static const struct cpr4_reg_data ipq9574_cpr_apss = { -+ .cpr_valid_fuse_count = IPQ9574_APSS_FUSE_CORNERS, -+ .fuse_ref_volt = ipq9574_apss_fuse_ref_volt, -+ .fuse_step_volt = IPQ9574_APSS_FUSE_STEP_VOLT, -+ .cpr_clk_rate = IPQ6018_APSS_CPR_CLOCK_RATE, -+ .boost_fuse_ref_volt = IPQ6018_APSS_BOOST_FUSE_REF_VOLT, -+ .boost_ceiling_volt = IPQ6018_APSS_BOOST_CEILING_VOLT, -+ .boost_floor_volt = IPQ6018_APSS_BOOST_FLOOR_VOLT, -+ .cpr3_fuse_params = &ipq9574_fuse_params, -+ .mem_acc_funcs = NULL, -+}; -+ -+static struct of_device_id cpr4_regulator_match_table[] = { -+ { -+ .compatible = "qcom,cpr4-ipq807x-apss-regulator", -+ .data = &ipq807x_cpr_apss -+ }, -+ { -+ .compatible = "qcom,cpr4-ipq817x-apss-regulator", -+ .data = &ipq817x_cpr_apss -+ }, -+ { -+ .compatible = "qcom,cpr4-ipq6018-apss-regulator", -+ .data = &ipq6018_cpr_apss -+ }, -+ { -+ .compatible = "qcom,cpr4-ipq9574-apss-regulator", -+ .data = &ipq9574_cpr_apss -+ }, -+ {} -+}; -+ -+static int cpr4_apss_regulator_probe(struct platform_device *pdev) -+{ -+ struct device *dev = &pdev->dev; -+ struct cpr3_controller *ctrl; -+ const struct of_device_id *match; -+ struct cpr4_reg_data *cpr_data; -+ int i, rc; -+ -+ if (!dev->of_node) { -+ dev_err(dev, "Device tree node is missing\n"); -+ return -EINVAL; -+ } -+ -+ ctrl = devm_kzalloc(dev, sizeof(*ctrl), GFP_KERNEL); -+ if (!ctrl) -+ return -ENOMEM; -+ -+ match = of_match_device(cpr4_regulator_match_table, &pdev->dev); -+ if (!match) -+ return -ENODEV; -+ -+ cpr_data = (struct cpr4_reg_data *)match->data; -+ g_valid_fuse_count = cpr_data->cpr_valid_fuse_count; -+ dev_info(dev, "CPR valid fuse count: %d\n", g_valid_fuse_count); -+ ctrl->cpr_clock_rate = cpr_data->cpr_clk_rate; -+ -+ ctrl->dev = dev; -+ /* Set to false later if anything precludes CPR operation. */ -+ ctrl->cpr_allowed_hw = true; -+ -+ rc = of_property_read_string(dev->of_node, "qcom,cpr-ctrl-name", -+ &ctrl->name); -+ if (rc) { -+ cpr3_err(ctrl, "unable to read qcom,cpr-ctrl-name, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ rc = cpr3_map_fuse_base(ctrl, pdev); -+ if (rc) { -+ cpr3_err(ctrl, "could not map fuse base address\n"); -+ return rc; -+ } -+ -+ rc = cpr3_read_tcsr_setting(ctrl, pdev, IPQ807x_APSS_CPR_TCSR_START, -+ IPQ807x_APSS_CPR_TCSR_END); -+ if (rc) { -+ cpr3_err(ctrl, "could not read CPR tcsr setting\n"); -+ return rc; -+ } -+ -+ rc = cpr3_allocate_threads(ctrl, 0, 0); -+ if (rc) { -+ cpr3_err(ctrl, "failed to allocate CPR thread array, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ if (ctrl->thread_count != 1) { -+ cpr3_err(ctrl, "expected 1 thread but found %d\n", -+ ctrl->thread_count); -+ return -EINVAL; -+ } -+ -+ rc = cpr4_apss_init_controller(ctrl); -+ if (rc) { -+ if (rc != -EPROBE_DEFER) -+ cpr3_err(ctrl, "failed to initialize CPR controller parameters, rc=%d\n", -+ rc); -+ return rc; -+ } -+ -+ rc = cpr4_apss_init_thread(&ctrl->thread[0]); -+ if (rc) { -+ cpr3_err(ctrl, "thread initialization failed, rc=%d\n", rc); -+ return rc; -+ } -+ -+ for (i = 0; i < ctrl->thread[0].vreg_count; i++) { -+ ctrl->thread[0].vreg[i].cpr4_regulator_data = cpr_data; -+ rc = cpr4_apss_init_regulator(&ctrl->thread[0].vreg[i]); -+ if (rc) { -+ cpr3_err(&ctrl->thread[0].vreg[i], "regulator initialization failed, rc=%d\n", -+ rc); -+ return rc; -+ } -+ } -+ -+ platform_set_drvdata(pdev, ctrl); -+ -+ return cpr3_regulator_register(pdev, ctrl); -+} -+ -+static int cpr4_apss_regulator_remove(struct platform_device *pdev) -+{ -+ struct cpr3_controller *ctrl = platform_get_drvdata(pdev); -+ -+ return cpr3_regulator_unregister(ctrl); -+} -+ -+static struct platform_driver cpr4_apss_regulator_driver = { -+ .driver = { -+ .name = "qcom,cpr4-apss-regulator", -+ .of_match_table = cpr4_regulator_match_table, -+ .owner = THIS_MODULE, -+ }, -+ .probe = cpr4_apss_regulator_probe, -+ .remove = cpr4_apss_regulator_remove, -+ .suspend = cpr4_apss_regulator_suspend, -+ .resume = cpr4_apss_regulator_resume, -+}; -+ -+static int cpr4_regulator_init(void) -+{ -+ return platform_driver_register(&cpr4_apss_regulator_driver); -+} -+ -+static void cpr4_regulator_exit(void) -+{ -+ platform_driver_unregister(&cpr4_apss_regulator_driver); -+} -+ -+MODULE_DESCRIPTION("CPR4 APSS regulator driver"); -+MODULE_LICENSE("GPL v2"); -+ -+arch_initcall(cpr4_regulator_init); -+module_exit(cpr4_regulator_exit); ---- /dev/null -+++ b/include/soc/qcom/socinfo.h -@@ -0,0 +1,463 @@ -+/* Copyright (c) 2009-2014, 2016, 2020, The Linux Foundation. All rights reserved. -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 and -+ * only version 2 as published by the Free Software Foundation. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ */ -+ -+#ifndef _ARCH_ARM_MACH_MSM_SOCINFO_H_ -+#define _ARCH_ARM_MACH_MSM_SOCINFO_H_ -+ -+#include -+ -+#define CPU_IPQ8074 323 -+#define CPU_IPQ8072 342 -+#define CPU_IPQ8076 343 -+#define CPU_IPQ8078 344 -+#define CPU_IPQ8070 375 -+#define CPU_IPQ8071 376 -+ -+#define CPU_IPQ8072A 389 -+#define CPU_IPQ8074A 390 -+#define CPU_IPQ8076A 391 -+#define CPU_IPQ8078A 392 -+#define CPU_IPQ8070A 395 -+#define CPU_IPQ8071A 396 -+ -+#define CPU_IPQ8172 397 -+#define CPU_IPQ8173 398 -+#define CPU_IPQ8174 399 -+ -+#define CPU_IPQ6018 402 -+#define CPU_IPQ6028 403 -+#define CPU_IPQ6000 421 -+#define CPU_IPQ6010 422 -+#define CPU_IPQ6005 453 -+ -+#define CPU_IPQ5010 446 -+#define CPU_IPQ5018 447 -+#define CPU_IPQ5028 448 -+#define CPU_IPQ5000 503 -+#define CPU_IPQ0509 504 -+#define CPU_IPQ0518 505 -+ -+#define CPU_IPQ9514 510 -+#define CPU_IPQ9554 512 -+#define CPU_IPQ9570 513 -+#define CPU_IPQ9574 514 -+#define CPU_IPQ9550 511 -+#define CPU_IPQ9510 521 -+ -+static inline int read_ipq_soc_version_major(void) -+{ -+ const int *prop; -+ prop = of_get_property(of_find_node_by_path("/"), "soc_version_major", -+ NULL); -+ -+ if (!prop) -+ return -EINVAL; -+ -+ return le32_to_cpu(*prop); -+} -+ -+static inline int read_ipq_cpu_type(void) -+{ -+ const int *prop; -+ prop = of_get_property(of_find_node_by_path("/"), "cpu_type", NULL); -+ /* -+ * Return Default CPU type if "cpu_type" property is not found in DTSI -+ */ -+ if (!prop) -+ return CPU_IPQ8074; -+ -+ return le32_to_cpu(*prop); -+} -+ -+static inline int cpu_is_ipq8070(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ8070; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq8071(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ8071; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq8072(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ8072; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq8074(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ8074; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq8076(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ8076; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq8078(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ8078; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq8072a(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ8072A; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq8074a(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ8074A; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq8076a(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ8076A; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq8078a(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ8078A; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq8070a(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ8070A; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq8071a(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ8071A; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq8172(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ8172; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq8173(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ8173; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq8174(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ8174; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq6018(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ6018; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq6028(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ6028; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq6000(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ6000; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq6010(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ6010; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq6005(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ6005; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq5010(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ5010; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq5018(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ5018; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq5028(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ5028; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq5000(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ5000; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq0509(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ0509; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq0518(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ0518; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq9514(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ9514; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq9554(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ9554; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq9570(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ9570; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq9574(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ9574; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq9550(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ9550; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq9510(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return read_ipq_cpu_type() == CPU_IPQ9510; -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq807x(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return cpu_is_ipq8072() || cpu_is_ipq8074() || -+ cpu_is_ipq8076() || cpu_is_ipq8078() || -+ cpu_is_ipq8070() || cpu_is_ipq8071() || -+ cpu_is_ipq8072a() || cpu_is_ipq8074a() || -+ cpu_is_ipq8076a() || cpu_is_ipq8078a() || -+ cpu_is_ipq8070a() || cpu_is_ipq8071a() || -+ cpu_is_ipq8172() || cpu_is_ipq8173() || -+ cpu_is_ipq8174(); -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq60xx(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return cpu_is_ipq6018() || cpu_is_ipq6028() || -+ cpu_is_ipq6000() || cpu_is_ipq6010() || -+ cpu_is_ipq6005(); -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq50xx(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return cpu_is_ipq5010() || cpu_is_ipq5018() || -+ cpu_is_ipq5028() || cpu_is_ipq5000() || -+ cpu_is_ipq0509() || cpu_is_ipq0518(); -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_ipq95xx(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return cpu_is_ipq9514() || cpu_is_ipq9554() || -+ cpu_is_ipq9570() || cpu_is_ipq9574() || -+ cpu_is_ipq9550() || cpu_is_ipq9510(); -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_nss_crypto_enabled(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return cpu_is_ipq807x() || cpu_is_ipq60xx() || -+ cpu_is_ipq50xx() || cpu_is_ipq9570() || -+ cpu_is_ipq9550() || cpu_is_ipq9574() || -+ cpu_is_ipq9554(); -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_internal_wifi_enabled(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return cpu_is_ipq807x() || cpu_is_ipq60xx() || -+ cpu_is_ipq50xx() || cpu_is_ipq9514() || -+ cpu_is_ipq9554() || cpu_is_ipq9574(); -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_uniphy1_enabled(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return cpu_is_ipq807x() || cpu_is_ipq60xx() || -+ cpu_is_ipq9554() || cpu_is_ipq9570() || -+ cpu_is_ipq9574() || cpu_is_ipq9550(); -+#else -+ return 0; -+#endif -+} -+ -+static inline int cpu_is_uniphy2_enabled(void) -+{ -+#ifdef CONFIG_ARCH_QCOM -+ return cpu_is_ipq807x() || cpu_is_ipq9570() || -+ cpu_is_ipq9574(); -+#else -+ return 0; -+#endif -+} -+ -+#endif /* _ARCH_ARM_MACH_MSM_SOCINFO_H_ */ diff --git a/target/linux/qualcommax/patches-6.1/0902-arm64-dts-ipq8074-add-label-to-clocks.patch b/target/linux/qualcommax/patches-6.1/0902-arm64-dts-ipq8074-add-label-to-clocks.patch deleted file mode 100644 index 9b8b4df12b..0000000000 --- a/target/linux/qualcommax/patches-6.1/0902-arm64-dts-ipq8074-add-label-to-clocks.patch +++ /dev/null @@ -1,24 +0,0 @@ -From 6baf7e4abcea6f7ac21eccf072a20078b39d064c Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Wed, 9 Feb 2022 23:13:26 +0100 -Subject: [PATCH] arm64: dts: ipq8074: add label to clocks - -Add label to clocks node as that makes it easy to add the NSS fixed -clocks that are required in their DTSI. - -Signed-off-by: Robert Marko ---- - arch/arm64/boot/dts/qcom/ipq8074.dtsi | 2 +- - 1 file changed, 1 insertion(+), 1 deletion(-) - ---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi -@@ -15,7 +15,7 @@ - compatible = "qcom,ipq8074"; - interrupt-parent = <&intc>; - -- clocks { -+ clocks: clocks { - sleep_clk: sleep_clk { - compatible = "fixed-clock"; - clock-frequency = <32768>; diff --git a/target/linux/qualcommax/patches-6.1/0903-psci-dont-advertise-OSI-support-for-IPQ6018.patch b/target/linux/qualcommax/patches-6.1/0903-psci-dont-advertise-OSI-support-for-IPQ6018.patch deleted file mode 100644 index 5fcb90098f..0000000000 --- a/target/linux/qualcommax/patches-6.1/0903-psci-dont-advertise-OSI-support-for-IPQ6018.patch +++ /dev/null @@ -1,40 +0,0 @@ -From 563db68137475d011b355bfe674d1b7a24778091 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Sat, 8 Oct 2022 22:26:31 +0200 -Subject: [PATCH] psci: dont advertise OSI support for IPQ6018 - -Some older IPQ60xx SoC series boards ship with TrustZone/QSEE firmware -older than TZ.WNS.5.1-00084 which will advertise OSI[1] but are broken -and trying to use OSI will cause the board to hang until WDT kicks in. - -So workaround it by checking for SoC compatible and returning false so -OSI is not used. - -[1] https://www.spinics.net/lists/linux-arm-msm/msg79916.html - -Signed-off-by: Robert Marko ---- - drivers/firmware/psci/psci.c | 12 ++++++++++++ - 1 file changed, 12 insertions(+) - ---- a/drivers/firmware/psci/psci.c -+++ b/drivers/firmware/psci/psci.c -@@ -87,6 +87,18 @@ static inline bool psci_has_ext_power_st - - bool psci_has_osi_support(void) - { -+ /* -+ * Some older IPQ60xx SoC series boards ship with -+ * TrustZone/QSEE firmware older than TZ.WNS.5.1-00084 -+ * which will advertise OSI but is broken and trying -+ * to use OSI will cause the board to hang until WDT -+ * kicks in. -+ * So workaround it by checking for SoC compatible -+ * and returning false so OSI is not used. -+ */ -+ if (of_machine_is_compatible("qcom,ipq6018")) -+ return false; -+ - return psci_cpu_suspend_feature & PSCI_1_0_OS_INITIATED; - } - diff --git a/target/linux/qualcommax/patches-6.1/0904-clk-qcom-ipq6018-workaround-networking-clock-parenti.patch b/target/linux/qualcommax/patches-6.1/0904-clk-qcom-ipq6018-workaround-networking-clock-parenti.patch deleted file mode 100644 index 175d475849..0000000000 --- a/target/linux/qualcommax/patches-6.1/0904-clk-qcom-ipq6018-workaround-networking-clock-parenti.patch +++ /dev/null @@ -1,109 +0,0 @@ -From 0c5b5243ad55ae744e790ba90c5ad37a93bd1377 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Tue, 11 Oct 2022 23:38:45 +0200 -Subject: [PATCH] clk: qcom: ipq6018: workaround networking clock parenting - -Currently, networking clocks are only looked up by fw_name however, -these are registered and setup by SSDK and are not available to the -GCC driver at all, so work around that by providing a global name -fallback. - -While we are here, provide global fallback for bias_pll_cc_clk and -bias_pll_nss_noc_clk as well as these are fixed clocks also not available -to the driver. - -Signed-off-by: Robert Marko ---- - drivers/clk/qcom/gcc-ipq6018.c | 39 +++++++++++++++++----------------- - 1 file changed, 19 insertions(+), 20 deletions(-) - ---- a/drivers/clk/qcom/gcc-ipq6018.c -+++ b/drivers/clk/qcom/gcc-ipq6018.c -@@ -361,7 +361,7 @@ static const struct freq_tbl ftbl_nss_pp - - static const struct clk_parent_data gcc_xo_bias_gpll0_gpll4_nss_ubi32[] = { - { .fw_name = "xo" }, -- { .fw_name = "bias_pll_cc_clk" }, -+ { .fw_name = "bias_pll_cc_clk", .name = "bias_pll_cc_clk" }, - { .hw = &gpll0.clkr.hw }, - { .hw = &gpll4.clkr.hw }, - { .hw = &nss_crypto_pll.clkr.hw }, -@@ -527,12 +527,12 @@ static const struct freq_tbl ftbl_nss_po - static const struct clk_parent_data - gcc_xo_uniphy0_rx_tx_uniphy1_rx_tx_ubi32_bias[] = { - { .fw_name = "xo" }, -- { .fw_name = "uniphy0_gcc_rx_clk" }, -- { .fw_name = "uniphy0_gcc_tx_clk" }, -- { .fw_name = "uniphy1_gcc_rx_clk" }, -- { .fw_name = "uniphy1_gcc_tx_clk" }, -+ { .fw_name = "uniphy0_gcc_rx_clk", .name = "uniphy0_gcc_rx_clk" }, -+ { .fw_name = "uniphy0_gcc_tx_clk", .name = "uniphy0_gcc_tx_clk" }, -+ { .fw_name = "uniphy1_gcc_rx_clk", .name = "uniphy1_gcc_rx_clk" }, -+ { .fw_name = "uniphy1_gcc_tx_clk", .name = "uniphy1_gcc_tx_clk" }, - { .hw = &ubi32_pll.clkr.hw }, -- { .fw_name = "bias_pll_cc_clk" }, -+ { .fw_name = "bias_pll_cc_clk", .name = "bias_pll_cc_clk" }, - }; - - static const struct parent_map -@@ -574,12 +574,12 @@ static const struct freq_tbl ftbl_nss_po - static const struct clk_parent_data - gcc_xo_uniphy0_tx_rx_uniphy1_tx_rx_ubi32_bias[] = { - { .fw_name = "xo" }, -- { .fw_name = "uniphy0_gcc_tx_clk" }, -- { .fw_name = "uniphy0_gcc_rx_clk" }, -- { .fw_name = "uniphy1_gcc_tx_clk" }, -- { .fw_name = "uniphy1_gcc_rx_clk" }, -+ { .fw_name = "uniphy0_gcc_tx_clk", .name = "uniphy0_gcc_tx_clk" }, -+ { .fw_name = "uniphy0_gcc_rx_clk", .name = "uniphy0_gcc_rx_clk" }, -+ { .fw_name = "uniphy1_gcc_tx_clk", .name = "uniphy1_gcc_tx_clk" }, -+ { .fw_name = "uniphy1_gcc_rx_clk", .name = "uniphy1_gcc_rx_clk" }, - { .hw = &ubi32_pll.clkr.hw }, -- { .fw_name = "bias_pll_cc_clk" }, -+ { .fw_name = "bias_pll_cc_clk", .name = "bias_pll_cc_clk" }, - }; - - static const struct parent_map -@@ -715,10 +715,10 @@ static const struct freq_tbl ftbl_nss_po - - static const struct clk_parent_data gcc_xo_uniphy0_rx_tx_ubi32_bias[] = { - { .fw_name = "xo" }, -- { .fw_name = "uniphy0_gcc_rx_clk" }, -- { .fw_name = "uniphy0_gcc_tx_clk" }, -+ { .fw_name = "uniphy0_gcc_rx_clk", .name = "uniphy0_gcc_rx_clk" }, -+ { .fw_name = "uniphy0_gcc_tx_clk", .name = "uniphy0_gcc_tx_clk" }, - { .hw = &ubi32_pll.clkr.hw }, -- { .fw_name = "bias_pll_cc_clk" }, -+ { .fw_name = "bias_pll_cc_clk", .name = "bias_pll_cc_clk" }, - }; - - static const struct parent_map gcc_xo_uniphy0_rx_tx_ubi32_bias_map[] = { -@@ -751,10 +751,10 @@ static const struct freq_tbl ftbl_nss_po - - static const struct clk_parent_data gcc_xo_uniphy0_tx_rx_ubi32_bias[] = { - { .fw_name = "xo" }, -- { .fw_name = "uniphy0_gcc_tx_clk" }, -- { .fw_name = "uniphy0_gcc_rx_clk" }, -+ { .fw_name = "uniphy0_gcc_tx_clk", .name = "uniphy0_gcc_tx_clk" }, -+ { .fw_name = "uniphy0_gcc_rx_clk", .name = "uniphy0_gcc_rx_clk" }, - { .hw = &ubi32_pll.clkr.hw }, -- { .fw_name = "bias_pll_cc_clk" }, -+ { .fw_name = "bias_pll_cc_clk", .name = "bias_pll_cc_clk" }, - }; - - static const struct parent_map gcc_xo_uniphy0_tx_rx_ubi32_bias_map[] = { -@@ -1898,12 +1898,11 @@ static const struct freq_tbl ftbl_ubi32_ - { } - }; - --static const struct clk_parent_data -- gcc_xo_gpll0_gpll2_bias_pll_nss_noc_clk[] = { -+static const struct clk_parent_data gcc_xo_gpll0_gpll2_bias_pll_nss_noc_clk[] = { - { .fw_name = "xo" }, - { .hw = &gpll0.clkr.hw }, - { .hw = &gpll2.clkr.hw }, -- { .fw_name = "bias_pll_nss_noc_clk" }, -+ { .fw_name = "bias_pll_nss_noc_clk", .name = "bias_pll_nss_noc_clk" }, - }; - - static const struct parent_map gcc_xo_gpll0_gpll2_bias_pll_nss_noc_clk_map[] = { diff --git a/target/linux/qualcommax/patches-6.1/0905-remoteproc-q6v5_wcss-change-ssr-name-for-ipq6018-wif.patch b/target/linux/qualcommax/patches-6.1/0905-remoteproc-q6v5_wcss-change-ssr-name-for-ipq6018-wif.patch deleted file mode 100644 index 58bea43892..0000000000 --- a/target/linux/qualcommax/patches-6.1/0905-remoteproc-q6v5_wcss-change-ssr-name-for-ipq6018-wif.patch +++ /dev/null @@ -1,40 +0,0 @@ -From 505f9c8653fc218ca47a153ec58ebc16bef5502f Mon Sep 17 00:00:00 2001 -From: Mantas Pucka -Date: Tue, 16 Jan 2024 10:42:40 +0200 -Subject: [PATCH 16/19] remoteproc: q6v5_wcss: change ssr name for ipq6018 wifi - subsystem - -On IPQ6018 this string ends up being sent to RPM when remoteproc stops -(on crash or rmmod ath11k). "q6wcss" is not a valid name (not found by -`strings` in rpm.mbn), so this causes RPM do 'something' (presumably crash) -causing a system reboot followed by hang in XBL, with no WDT running. -Let's change ssr_name to a more sensible 'wcnss', that does not cause such -issues. - -Signed-off-by: Mantas Pucka ---- - drivers/remoteproc/qcom_q6v5_wcss.c | 6 +++--- - 1 file changed, 3 insertions(+), 3 deletions(-) - ---- a/drivers/remoteproc/qcom_q6v5_wcss.c -+++ b/drivers/remoteproc/qcom_q6v5_wcss.c -@@ -1143,8 +1143,8 @@ static int q6v5_wcss_probe(struct platfo - if (ret) - goto free_rproc; - -- qcom_add_glink_subdev(rproc, &wcss->glink_subdev, "q6wcss"); -- qcom_add_ssr_subdev(rproc, &wcss->ssr_subdev, "q6wcss"); -+ qcom_add_glink_subdev(rproc, &wcss->glink_subdev, desc->ssr_name); -+ qcom_add_ssr_subdev(rproc, &wcss->ssr_subdev, desc->ssr_name); - - if (desc->ssctl_id) - wcss->sysmon = qcom_add_sysmon_subdev(rproc, -@@ -1201,7 +1201,7 @@ static const struct wcss_data wcss_ipq60 - .aon_reset_required = true, - .wcss_q6_reset_required = true, - .bcr_reset_required = false, -- .ssr_name = "q6wcss", -+ .ssr_name = "wcnss", - .ops = &q6v5_wcss_ipq8074_ops, - .requires_force_stop = true, - .need_mem_protection = true, diff --git a/target/linux/qualcommax/patches-6.1/0906-arm64-dts-qcom-ipq6018-add-wifi-node.patch b/target/linux/qualcommax/patches-6.1/0906-arm64-dts-qcom-ipq6018-add-wifi-node.patch deleted file mode 100644 index 247df110ff..0000000000 --- a/target/linux/qualcommax/patches-6.1/0906-arm64-dts-qcom-ipq6018-add-wifi-node.patch +++ /dev/null @@ -1,120 +0,0 @@ -From 153c74fc80b9f33ed1a50d7790bf6979fdceb370 Mon Sep 17 00:00:00 2001 -From: Mantas Pucka -Date: Tue, 16 Jan 2024 11:41:06 +0200 -Subject: [PATCH 19/19] arm64: dts: qcom: ipq6018: add wifi node - -IPQ6018 has a AHB based Q6v5 802.11ax radios that are supported -by the ath11k. - -Add the required DT node to enable the built-in radios. - -Signed-off-by: Mantas Pucka ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 96 +++++++++++++++++++++++++++++++++++ - 1 file changed, 96 insertions(+) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -807,6 +807,102 @@ - }; - }; - -+ wifi: wifi@c000000 { -+ compatible = "qcom,ipq6018-wifi"; -+ reg = <0x0 0xc000000 0x0 0x1000000>; -+ qcom,rproc = <&q6v5_wcss>; -+ interrupts = , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ ; -+ interrupt-names = "misc-pulse1", "misc-latch", "sw-exception", -+ "watchdog", "ce0", "ce1", "ce2", "ce3", "ce4", -+ "ce5", "ce6", "ce7", "ce8", "ce9", "ce10", -+ "ce11", "host2wbm-desc-feed", -+ "host2reo-re-injection", "host2reo-command", -+ "host2rxdma-monitor-ring3", -+ "host2rxdma-monitor-ring2", -+ "host2rxdma-monitor-ring1", -+ "reo2ost-exception", "wbm2host-rx-release", -+ "reo2host-status", -+ "reo2host-destination-ring4", -+ "reo2host-destination-ring3", -+ "reo2host-destination-ring2", -+ "reo2host-destination-ring1", -+ "rxdma2host-monitor-destination-mac3", -+ "rxdma2host-monitor-destination-mac2", -+ "rxdma2host-monitor-destination-mac1", -+ "ppdu-end-interrupts-mac3", -+ "ppdu-end-interrupts-mac2", -+ "ppdu-end-interrupts-mac1", -+ "rxdma2host-monitor-status-ring-mac3", -+ "rxdma2host-monitor-status-ring-mac2", -+ "rxdma2host-monitor-status-ring-mac1", -+ "host2rxdma-host-buf-ring-mac3", -+ "host2rxdma-host-buf-ring-mac2", -+ "host2rxdma-host-buf-ring-mac1", -+ "rxdma2host-destination-ring-mac3", -+ "rxdma2host-destination-ring-mac2", -+ "rxdma2host-destination-ring-mac1", -+ "host2tcl-input-ring4", -+ "host2tcl-input-ring3", -+ "host2tcl-input-ring2", -+ "host2tcl-input-ring1", -+ "wbm2host-tx-completions-ring3", -+ "wbm2host-tx-completions-ring2", -+ "wbm2host-tx-completions-ring1", -+ "tcl2host-status-ring"; -+ status = "disabled"; -+ }; -+ - q6v5_wcss: remoteproc@cd00000 { - compatible = "qcom,ipq6018-wcss-pil"; - reg = <0x0 0x0cd00000 0x0 0x4040>, diff --git a/target/linux/qualcommax/patches-6.1/0907-soc-qcom-fix-smp2p-ack-on-ipq6018.patch b/target/linux/qualcommax/patches-6.1/0907-soc-qcom-fix-smp2p-ack-on-ipq6018.patch deleted file mode 100644 index 88e294562d..0000000000 --- a/target/linux/qualcommax/patches-6.1/0907-soc-qcom-fix-smp2p-ack-on-ipq6018.patch +++ /dev/null @@ -1,53 +0,0 @@ -From d93936f175bd914067df8f63f5fbe6e3b77bb4d2 Mon Sep 17 00:00:00 2001 -From: Mantas Pucka -Date: Tue, 23 May 2023 14:46:28 +0300 -Subject: [PATCH 11/19] soc: qcom: fix smp2p ack on ipq6018 - -IPQ6018 seem to need different ack mechanism for smp2p messaging. This -fixes q6v5_wcss remoteproc firmware reloading. Without this first load -is OK, but subsequent loads would hang and fail to complete. - -Signed-off-by: Mantas Pucka ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 1 + - drivers/soc/qcom/smp2p.c | 6 +++++- - 2 files changed, 6 insertions(+), 1 deletion(-) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -1155,6 +1155,7 @@ - - wcss_smp2p_out: master-kernel { - qcom,entry-name = "master-kernel"; -+ qcom,smp2p-feature-ssr-ack; - #qcom,smem-state-cells = <1>; - }; - ---- a/drivers/soc/qcom/smp2p.c -+++ b/drivers/soc/qcom/smp2p.c -@@ -158,6 +158,8 @@ struct qcom_smp2p { - - struct list_head inbound; - struct list_head outbound; -+ -+ bool need_ssr_ack; - }; - - static void qcom_smp2p_kick(struct qcom_smp2p *smp2p) -@@ -306,7 +308,7 @@ static irqreturn_t qcom_smp2p_intr(int i - ack_restart = qcom_smp2p_check_ssr(smp2p); - qcom_smp2p_notify_in(smp2p); - -- if (ack_restart) -+ if (ack_restart || smp2p->need_ssr_ack) - qcom_smp2p_do_ssr_ack(smp2p); - } - -@@ -427,6 +429,7 @@ static int qcom_smp2p_outbound_entry(str - - /* Make the logical entry reference the physical value */ - entry->value = &out->entries[out->valid_entries].value; -+ smp2p->need_ssr_ack = of_property_read_bool(node, "qcom,smp2p-feature-ssr-ack"); - - out->valid_entries++; - diff --git a/target/linux/qualcommax/patches-6.1/0908-remoteproc-qcom_q6v5_wcss-add-optional-qdss_at-clock.patch b/target/linux/qualcommax/patches-6.1/0908-remoteproc-qcom_q6v5_wcss-add-optional-qdss_at-clock.patch deleted file mode 100644 index cfc9adda04..0000000000 --- a/target/linux/qualcommax/patches-6.1/0908-remoteproc-qcom_q6v5_wcss-add-optional-qdss_at-clock.patch +++ /dev/null @@ -1,55 +0,0 @@ -From 87dbcc69a7e3fe6ccddf4fe9bdbf51330f5e4a77 Mon Sep 17 00:00:00 2001 -From: Mantas Pucka -Date: Tue, 23 Jan 2024 11:04:04 +0200 -Subject: [PATCH] remoteproc: qcom_q6v5_wcss: add optional qdss_at clock - -IPQ6018 needs QDSS_AT clock enabled when loading wifi. Optionally enable it -when provided by DT. - -Signed-off-by: Mantas Pucka ---- - drivers/remoteproc/qcom_q6v5_wcss.c | 24 ++++++++++++++++++++++++ - 1 file changed, 24 insertions(+) - ---- a/drivers/remoteproc/qcom_q6v5_wcss.c -+++ b/drivers/remoteproc/qcom_q6v5_wcss.c -@@ -120,6 +120,7 @@ struct q6v5_wcss { - struct clk *qdsp6ss_core_gfmux; - struct clk *lcc_bcr_sleep; - struct clk *prng_clk; -+ struct clk *qdss_clk; - struct regulator *cx_supply; - struct qcom_sysmon *sysmon; - -@@ -259,6 +260,9 @@ static int q6v5_wcss_start(struct rproc - return ret; - } - -+ if (wcss->qdss_clk) -+ clk_prepare_enable(wcss->qdss_clk); -+ - qcom_q6v5_prepare(&wcss->q6v5); - - if (wcss->need_mem_protection) { -@@ -772,6 +776,8 @@ static int q6v5_wcss_stop(struct rproc * - } - - pas_done: -+ if (wcss->qdss_clk) -+ clk_disable_unprepare(wcss->qdss_clk); - clk_disable_unprepare(wcss->prng_clk); - qcom_q6v5_unprepare(&wcss->q6v5); - -@@ -981,6 +987,12 @@ static int ipq_init_clock(struct q6v5_wc - dev_err(wcss->dev, "Failed to get prng clock\n"); - return ret; - } -+ -+ wcss->qdss_clk = devm_clk_get(wcss->dev, "qdss"); -+ if (IS_ERR(wcss->qdss_clk)) { -+ wcss->qdss_clk = NULL; -+ } -+ - return 0; - } - diff --git a/target/linux/qualcommax/patches-6.1/0909-arm64-dts-qcom-ipq6018-assign-QDSS_AT-clock-to-wifi-.patch b/target/linux/qualcommax/patches-6.1/0909-arm64-dts-qcom-ipq6018-assign-QDSS_AT-clock-to-wifi-.patch deleted file mode 100644 index 0a7a100f6a..0000000000 --- a/target/linux/qualcommax/patches-6.1/0909-arm64-dts-qcom-ipq6018-assign-QDSS_AT-clock-to-wifi-.patch +++ /dev/null @@ -1,26 +0,0 @@ -From 71f30e25d21ae4981ecef6653a4ba7dfeb80db7b Mon Sep 17 00:00:00 2001 -From: Mantas Pucka -Date: Tue, 23 Jan 2024 11:04:57 +0200 -Subject: [PATCH] arm64: dts: qcom: ipq6018: assign QDSS_AT clock to wifi remoteproc - -IPQ6018 needs to enable QDSS_AT clock when loading wifi firmware, -add it to wifi remoteproc clock list. - -Signed-off-by: Mantas Pucka ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 15 ++++++++------- - 1 file changed, 9 insertions(+), 8 deletions(-) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -928,8 +928,8 @@ - "wcss_reset", - "wcss_q6_reset"; - -- clocks = <&gcc GCC_PRNG_AHB_CLK>; -- clock-names = "prng"; -+ clocks = <&gcc GCC_PRNG_AHB_CLK>, <&gcc GCC_QDSS_AT_CLK>; -+ clock-names = "prng", "qdss" ; - - qcom,halt-regs = <&tcsr 0x18000 0x1b000 0xe000>; - diff --git a/target/linux/qualcommax/patches-6.1/0910-arm64-dts-qcom-ipq6018-change-voltage-to-perf-levels.patch b/target/linux/qualcommax/patches-6.1/0910-arm64-dts-qcom-ipq6018-change-voltage-to-perf-levels.patch deleted file mode 100644 index 17784235c3..0000000000 --- a/target/linux/qualcommax/patches-6.1/0910-arm64-dts-qcom-ipq6018-change-voltage-to-perf-levels.patch +++ /dev/null @@ -1,65 +0,0 @@ -From c67a1814bb1d0df290cf1e3f9c966f04aa41b9b9 Mon Sep 17 00:00:00 2001 -From: Mantas Pucka -Date: Tue, 30 Jan 2024 12:43:56 +0200 -Subject: [PATCH] arm64: dts: qcom: ipq6018: change voltage to perf levels for - CPR4 driver - -Current CPR4 driver requires opp-microvolt to be an abstract -performance level instead of actual voltage level. - -Signed-off-by: Mantas Pucka ---- - arch/arm64/boot/dts/qcom/ipq6018.dtsi | 12 ++++++------ - 1 file changed, 6 insertions(+), 6 deletions(-) - ---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi -+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi -@@ -106,42 +106,42 @@ - - opp-864000000 { - opp-hz = /bits/ 64 <864000000>; -- opp-microvolt = <725000>; -+ opp-microvolt = <1>; - opp-supported-hw = <0xf>; - clock-latency-ns = <200000>; - }; - - opp-1056000000 { - opp-hz = /bits/ 64 <1056000000>; -- opp-microvolt = <787500>; -+ opp-microvolt = <2>; - opp-supported-hw = <0xf>; - clock-latency-ns = <200000>; - }; - - opp-1320000000 { - opp-hz = /bits/ 64 <1320000000>; -- opp-microvolt = <862500>; -+ opp-microvolt = <3>; - opp-supported-hw = <0x3>; - clock-latency-ns = <200000>; - }; - - opp-1440000000 { - opp-hz = /bits/ 64 <1440000000>; -- opp-microvolt = <925000>; -+ opp-microvolt = <4>; - opp-supported-hw = <0x3>; - clock-latency-ns = <200000>; - }; - - opp-1608000000 { - opp-hz = /bits/ 64 <1608000000>; -- opp-microvolt = <987500>; -+ opp-microvolt = <5>; - opp-supported-hw = <0x1>; - clock-latency-ns = <200000>; - }; - - opp-1800000000 { - opp-hz = /bits/ 64 <1800000000>; -- opp-microvolt = <1062500>; -+ opp-microvolt = <6>; - opp-supported-hw = <0x1>; - clock-latency-ns = <200000>; - };