From: Rafał Miłecki Date: Sun, 12 Apr 2015 20:00:42 +0000 (+0000) Subject: b53: improve overriding CPU port state on BCM5301X X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=06ac2f5c74308807f9222ee43f2c81c341792072;p=openwrt%2Fstaging%2F981213.git b53: improve overriding CPU port state on BCM5301X On BCM5301X there are two different cases to handle: CPU port 8 vs. any other one. Support for CPU port 8 was already partially implemented but it lacked setting some extra bit for 2G speed. It also will need to be extended to implement "SMP dual core 3 GMAC setup". That's the reason for handling it in separated code block. This patch also adds overriding CPU port state for port other than 8. It requires using recently defined GMII_PORT registers. It was tested for regressions on BCM53011 revs 2 & 3. It was also confirmed to fix switch on some internal Broadcom board. Signed-off-by: Rafał Miłecki Acked-by: Jonas Gorski SVN-Revision: 45402 --- diff --git a/target/linux/generic/files/drivers/net/phy/b53/b53_common.c b/target/linux/generic/files/drivers/net/phy/b53/b53_common.c index d2bb51ab4a..ac7c10cadc 100644 --- a/target/linux/generic/files/drivers/net/phy/b53/b53_common.c +++ b/target/linux/generic/files/drivers/net/phy/b53/b53_common.c @@ -480,6 +480,7 @@ static void b53_switch_reset_gpio(struct b53_device *dev) static int b53_switch_reset(struct b53_device *dev) { + u8 cpu_port = dev->sw_dev.cpu_port; u8 mgmt; b53_switch_reset_gpio(dev); @@ -525,8 +526,7 @@ static int b53_switch_reset(struct b53_device *dev) return -EINVAL; } } - } else if ((is531x5(dev) || is5301x(dev)) && - dev->sw_dev.cpu_port == B53_CPU_PORT) { + } else if (is531x5(dev) && cpu_port == B53_CPU_PORT) { u8 mii_port_override; b53_read8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, @@ -534,6 +534,33 @@ static int b53_switch_reset(struct b53_device *dev) b53_write8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, mii_port_override | PORT_OVERRIDE_EN | PORT_OVERRIDE_LINK); + } else if (is5301x(dev)) { + if (cpu_port == 8) { + u8 mii_port_override; + + b53_read8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, + &mii_port_override); + mii_port_override |= PORT_OVERRIDE_LINK | + PORT_OVERRIDE_RX_FLOW | + PORT_OVERRIDE_TX_FLOW | + PORT_OVERRIDE_SPEED_2000M | + PORT_OVERRIDE_EN; + b53_write8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, + mii_port_override); + + /* TODO: Ports 5 & 7 require some extra handling */ + } else { + u8 po_reg = B53_GMII_PORT_OVERRIDE_CTRL(cpu_port); + u8 gmii_po; + + b53_read8(dev, B53_CTRL_PAGE, po_reg, &gmii_po); + gmii_po |= GMII_PO_LINK | + GMII_PO_RX_FLOW | + GMII_PO_TX_FLOW | + GMII_PO_EN | + GMII_PO_SPEED_2000M; + b53_write8(dev, B53_CTRL_PAGE, po_reg, gmii_po); + } } b53_enable_mib(dev); diff --git a/target/linux/generic/files/drivers/net/phy/b53/b53_regs.h b/target/linux/generic/files/drivers/net/phy/b53/b53_regs.h index 534170832a..eef5c81779 100644 --- a/target/linux/generic/files/drivers/net/phy/b53/b53_regs.h +++ b/target/linux/generic/files/drivers/net/phy/b53/b53_regs.h @@ -86,6 +86,7 @@ #define PORT_OVERRIDE_RV_MII_25 BIT(4) /* BCM5325 only */ #define PORT_OVERRIDE_RX_FLOW BIT(4) #define PORT_OVERRIDE_TX_FLOW BIT(5) +#define PORT_OVERRIDE_SPEED_2000M BIT(6) /* BCM5301X only, requires setting 1000M */ #define PORT_OVERRIDE_EN BIT(7) /* Use the register contents */ /* Power-down mode control */