From: Piotr Dymacz Date: Thu, 6 Oct 2016 00:19:17 +0000 (+0200) Subject: ar71xx: add support for YunCore AP90Q X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=01dda0659eb7d029672af3bd3b590d98e2ee0a5d;p=openwrt%2Fstaging%2Fneocturne.git ar71xx: add support for YunCore AP90Q YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2. Short specification: - 650/600/216 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, passive PoE support - 64/128 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz with external PA, up to 29 dBm - 2x internal 5 dBi omni antennas - 4x LED, 1x button - UART (JP1) header on PCB Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000" 5. saveenv && reset Flash instruction under vendor fimrware, using telnet/SSH: 1. Connect PC with 192.168.1.x address to WAN port 2. Power up device, enter failsafe mode with button (no LED indicator!) 3. Change root password and reboot (mount_root, passwd ..., reboot -f) 4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP 5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 6. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9f050000" - mtd erase firmware - mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware Signed-off-by: Piotr Dymacz --- diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds index 29ee5d7b12..c348b4fbda 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/01_leds +++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds @@ -57,6 +57,17 @@ ap147-010) ucidef_set_led_switch "lan4" "LAN4" "ap147:green:lan4" "switch0" "0x02" ucidef_set_led_wlan "wlan2g" "WLAN 2.4 GHz" "ap147:green:wlan-2g" "phy0tpt" ;; +ap90q|\ +dr531) + ucidef_set_led_netdev "lan" "LAN" "$board:green:lan" "eth0" + ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth1" + + case "$board" in + ap90q) + ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt" + ;; + esac + ;; bhr-4grv2) ucidef_set_led_default "power" "POWER" "buffalo:green:power" "1" ucidef_set_led_default "diag" "DIAG" "buffalo:red:diag" "0" @@ -152,10 +163,6 @@ cr5000) ucidef_set_led_wlan "wlan" "WLAN" "pcs:blue:wlan" "phy0tpt" ucidef_set_led_usbdev "usb" "USB" "pcs:white:wps" "1-1" ;; -dr531) - ucidef_set_led_netdev "lan" "LAN" "$board:green:lan" "eth0" - ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth1" - ;; dragino2) ucidef_set_led_wlan "wlan" "WLAN" "$board:red:wlan" "phy0tpt" ucidef_set_led_netdev "lan" "LAN" "$board:red:lan" "eth0" diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh index bb42843245..0ef5a52a05 100644 --- a/target/linux/ar71xx/base-files/etc/diag.sh +++ b/target/linux/ar71xx/base-files/etc/diag.sh @@ -47,6 +47,10 @@ get_status_led() { tl-wpa8630) status_led="$board:green:power" ;; + ap90q|\ + gl-inet) + status_led="$board:green:lan" + ;; ap96) status_led="$board:green:led2" ;; @@ -168,9 +172,6 @@ get_status_led() { f9k1115v2) status_led="belkin:blue:status" ;; - gl-inet) - status_led="$board:green:lan" - ;; epg5000|\ esr1750) status_led="$board:amber:power" diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh index 8f710e6d5e..16ee2eb578 100755 --- a/target/linux/ar71xx/base-files/lib/ar71xx.sh +++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh @@ -470,6 +470,9 @@ ar71xx_board_detect() { *AP83) name="ap83" ;; + *AP90Q) + name="ap90q" + ;; *"Archer C5") name="archer-c5" ;; diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh index 87c9d8fc89..697b786937 100755 --- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh @@ -178,6 +178,7 @@ platform_check_image() { ap132|\ ap81|\ ap83|\ + ap90q|\ bullet-m|\ c-55|\ carambola2|\ diff --git a/target/linux/ar71xx/config-4.4 b/target/linux/ar71xx/config-4.4 index 550b8bbce5..471a44d056 100644 --- a/target/linux/ar71xx/config-4.4 +++ b/target/linux/ar71xx/config-4.4 @@ -49,6 +49,7 @@ CONFIG_ATH79_MACH_AP147=y CONFIG_ATH79_MACH_AP152=y CONFIG_ATH79_MACH_AP81=y CONFIG_ATH79_MACH_AP83=y +CONFIG_ATH79_MACH_AP90Q=y CONFIG_ATH79_MACH_AP96=y CONFIG_ATH79_MACH_ARCHER_C7=y CONFIG_ATH79_MACH_ARDUINO_YUN=y diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt index 3a3ed14b41..e9431f139e 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt +++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt @@ -174,6 +174,15 @@ config ATH79_MACH_AP83 select ATH79_DEV_USB select ATH79_DEV_WMAC +config ATH79_MACH_AP90Q + bool "YunCore AP90Q support" + select SOC_QCA953X + select ATH79_DEV_ETH + select ATH79_DEV_GPIO_BUTTONS + select ATH79_DEV_LEDS_GPIO + select ATH79_DEV_M25P80 + select ATH79_DEV_WMAC + config ATH79_MACH_AP96 bool "Atheros AP96 board support" select SOC_AR71XX diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile b/target/linux/ar71xx/files/arch/mips/ath79/Makefile index 1924179cf3..c0caccdb23 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile +++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile @@ -55,6 +55,7 @@ obj-$(CONFIG_ATH79_MACH_AP147) += mach-ap147.o obj-$(CONFIG_ATH79_MACH_AP152) += mach-ap152.o obj-$(CONFIG_ATH79_MACH_AP81) += mach-ap81.o obj-$(CONFIG_ATH79_MACH_AP83) += mach-ap83.o +obj-$(CONFIG_ATH79_MACH_AP90Q) += mach-ap90q.o obj-$(CONFIG_ATH79_MACH_AP96) += mach-ap96.o obj-$(CONFIG_ATH79_MACH_ARCHER_C7) += mach-archer-c7.o obj-$(CONFIG_ATH79_MACH_ARDUINO_YUN) += mach-arduino-yun.o diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-ap90q.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-ap90q.c new file mode 100644 index 0000000000..35e578122e --- /dev/null +++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-ap90q.c @@ -0,0 +1,123 @@ +/* + * YunCore AP90Q board support + * + * Copyright (C) 2016 Piotr Dymacz + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published + * by the Free Software Foundation. + */ + +#include +#include + +#include +#include + +#include "common.h" +#include "dev-eth.h" +#include "dev-gpio-buttons.h" +#include "dev-leds-gpio.h" +#include "dev-m25p80.h" +#include "dev-usb.h" +#include "dev-wmac.h" +#include "machtypes.h" + +#define AP90Q_GPIO_LED_WAN 4 +#define AP90Q_GPIO_LED_WLAN 12 +#define AP90Q_GPIO_LED_LAN 16 + +#define AP90Q_GPIO_BTN_RESET 17 + +#define AP90Q_KEYS_POLL_INTERVAL 20 +#define AP90Q_KEYS_DEBOUNCE_INTERVAL (3 * AP90Q_KEYS_POLL_INTERVAL) + +static struct gpio_led ap90q_leds_gpio[] __initdata = { + { + .name = "ap90q:green:lan", + .gpio = AP90Q_GPIO_LED_LAN, + .active_low = 1, + }, + { + .name = "ap90q:green:wan", + .gpio = AP90Q_GPIO_LED_WAN, + .active_low = 1, + }, + { + .name = "ap90q:green:wlan", + .gpio = AP90Q_GPIO_LED_WLAN, + .active_low = 1, + }, +}; + +static struct gpio_keys_button ap90q_gpio_keys[] __initdata = { + { + .desc = "reset", + .type = EV_KEY, + .code = KEY_RESTART, + .debounce_interval = AP90Q_KEYS_DEBOUNCE_INTERVAL, + .gpio = AP90Q_GPIO_BTN_RESET, + .active_low = 1, + }, +}; + +static void __init ap90q_gpio_setup(void) +{ + /* For LED on GPIO4 */ + ath79_gpio_function_disable(AR934X_GPIO_FUNC_CLK_OBS4_EN); + + ath79_gpio_direction_select(AP90Q_GPIO_LED_LAN, true); + ath79_gpio_direction_select(AP90Q_GPIO_LED_WAN, true); + ath79_gpio_direction_select(AP90Q_GPIO_LED_WLAN, true); + + /* Mute LEDs on boot */ + gpio_set_value(AP90Q_GPIO_LED_LAN, 1); + gpio_set_value(AP90Q_GPIO_LED_WAN, 1); + + ath79_gpio_output_select(AP90Q_GPIO_LED_LAN, 0); + ath79_gpio_output_select(AP90Q_GPIO_LED_WAN, 0); + ath79_gpio_output_select(AP90Q_GPIO_LED_WLAN, 0); + + ath79_register_leds_gpio(-1, ARRAY_SIZE(ap90q_leds_gpio), + ap90q_leds_gpio); + + ath79_register_gpio_keys_polled(-1, AP90Q_KEYS_POLL_INTERVAL, + ARRAY_SIZE(ap90q_gpio_keys), + ap90q_gpio_keys); +} + +static void __init ap90q_setup(void) +{ + u8 *art = (u8 *) KSEG1ADDR(0x1fff1000); + u8 *mac = (u8 *) KSEG1ADDR(0x1fff0000); + + ath79_register_m25p80(NULL); + + ap90q_gpio_setup(); + + ath79_setup_ar933x_phy4_switch(false, false); + + ath79_register_mdio(0, 0x0); + + ath79_switch_data.phy4_mii_en = 1; + ath79_switch_data.phy_poll_mask |= BIT(4); + + /* LAN */ + ath79_eth1_data.duplex = DUPLEX_FULL; + ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII; + ath79_eth1_data.speed = SPEED_1000; + ath79_init_mac(ath79_eth1_data.mac_addr, mac, 1); + ath79_register_eth(1); + + /* WAN */ + ath79_eth0_data.duplex = DUPLEX_FULL; + ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII; + ath79_eth0_data.speed = SPEED_100; + ath79_eth0_data.phy_mask = BIT(4); + ath79_init_mac(ath79_eth0_data.mac_addr, mac, 0); + ath79_register_eth(0); + + ath79_register_wmac(art, NULL); +} + +MIPS_MACHINE(ATH79_MACH_AP90Q, "AP90Q", "YunCore AP90Q", ap90q_setup); diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h index 5e504b1242..e69cf3bece 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h +++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h @@ -38,6 +38,7 @@ enum ath79_mach_type { ATH79_MACH_AP152, /* Atheros AP152 reference board */ ATH79_MACH_AP81, /* Atheros AP81 reference board */ ATH79_MACH_AP83, /* Atheros AP83 */ + ATH79_MACH_AP90Q, /* YunCore AP90Q */ ATH79_MACH_AP96, /* Atheros AP96 */ ATH79_MACH_ARCHER_C5, /* TP-LINK Archer C5 board */ ATH79_MACH_ARCHER_C7, /* TP-LINK Archer C7 board */ diff --git a/target/linux/ar71xx/image/generic.mk b/target/linux/ar71xx/image/generic.mk index 7381eecb9f..0c32cddfdd 100644 --- a/target/linux/ar71xx/image/generic.mk +++ b/target/linux/ar71xx/image/generic.mk @@ -1,3 +1,12 @@ +define Device/ap90q + DEVICE_TITLE := YunCore AP90Q + BOARDNAME = AP90Q + IMAGE_SIZE = 16000k + CONSOLE = ttyS0,115200 + MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env),16000k(firmware),64k(art)ro +endef +TARGET_DEVICES += ap90q + define Device/bsb DEVICE_TITLE := Smart Electronics Black Swift board DEVICE_PACKAGES := kmod-usb-core kmod-usb2