Don't switch to it by default yet as it requires more testing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
--- /dev/null
+CONFIG_ALIGNMENT_TRAP=y
+CONFIG_ARCH_BCM=y
+CONFIG_ARCH_BCM_5301X=y
+CONFIG_ARCH_BCM_53573=y
+CONFIG_ARCH_BCM_IPROC=y
+CONFIG_ARCH_CLOCKSOURCE_DATA=y
+CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
+CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
+CONFIG_ARCH_HAS_SG_CHAIN=y
+CONFIG_ARCH_HAS_TICK_BROADCAST=y
+CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
+CONFIG_ARCH_HIBERNATION_POSSIBLE=y
+CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
+CONFIG_ARCH_MULTIPLATFORM=y
+# CONFIG_ARCH_MULTI_CPU_AUTO is not set
+CONFIG_ARCH_MULTI_V6_V7=y
+CONFIG_ARCH_MULTI_V7=y
+CONFIG_ARCH_NR_GPIO=0
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
+CONFIG_ARCH_SUPPORTS_UPROBES=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_ARCH_USE_BUILTIN_BSWAP=y
+CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
+CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
+CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
+CONFIG_ARM=y
+CONFIG_ARM_AMBA=y
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_ARM_ARCH_TIMER=y
+CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y
+# CONFIG_ARM_ATAG_DTB_COMPAT is not set
+# CONFIG_ARM_CPU_SUSPEND is not set
+CONFIG_ARM_ERRATA_754322=y
+CONFIG_ARM_ERRATA_764369=y
+CONFIG_ARM_ERRATA_775420=y
+CONFIG_ARM_GIC=y
+CONFIG_ARM_GLOBAL_TIMER=y
+CONFIG_ARM_HAS_SG_CHAIN=y
+CONFIG_ARM_HEAVY_MB=y
+CONFIG_ARM_L1_CACHE_SHIFT=6
+CONFIG_ARM_L1_CACHE_SHIFT_6=y
+# CONFIG_ARM_LPAE is not set
+CONFIG_ARM_PATCH_IDIV=y
+CONFIG_ARM_PATCH_PHYS_VIRT=y
+# CONFIG_ARM_SP805_WATCHDOG is not set
+CONFIG_ARM_THUMB=y
+# CONFIG_ARM_THUMBEE is not set
+CONFIG_ARM_VIRT_EXT=y
+CONFIG_ATAGS=y
+CONFIG_AUTO_ZRELADDR=y
+CONFIG_BCM47XX_NVRAM=y
+CONFIG_BCM47XX_SPROM=y
+CONFIG_BCM47XX_WDT=y
+CONFIG_BCMA=y
+CONFIG_BCMA_BLOCKIO=y
+CONFIG_BCMA_DEBUG=y
+CONFIG_BCMA_DRIVER_GMAC_CMN=y
+CONFIG_BCMA_DRIVER_GPIO=y
+CONFIG_BCMA_DRIVER_PCI=y
+CONFIG_BCMA_HOST_PCI=y
+CONFIG_BCMA_HOST_PCI_POSSIBLE=y
+CONFIG_BCMA_HOST_SOC=y
+CONFIG_BCMA_SFLASH=y
+CONFIG_BCM_NET_PHYLIB=y
+CONFIG_BCM_NS_THERMAL=y
+CONFIG_BGMAC=y
+CONFIG_BGMAC_BCMA=y
+# CONFIG_BGMAC_PLATFORM is not set
+# CONFIG_BINFMT_FLAT is not set
+CONFIG_BLK_MQ_PCI=y
+CONFIG_BOUNCE=y
+CONFIG_BROADCOM_PHY=y
+CONFIG_CACHE_L2X0=y
+CONFIG_CLKDEV_LOOKUP=y
+CONFIG_CLKSRC_ARM_GLOBAL_TIMER_SCHED_CLOCK=y
+CONFIG_CLKSRC_MMIO=y
+CONFIG_CLKSRC_OF=y
+CONFIG_CLKSRC_PROBE=y
+# CONFIG_CLK_BCM_NS2 is not set
+CONFIG_CLK_BCM_NSP=y
+CONFIG_CLONE_BACKWARDS=y
+CONFIG_COMMON_CLK=y
+CONFIG_COMMON_CLK_IPROC=y
+CONFIG_CPU_32v6K=y
+CONFIG_CPU_32v7=y
+CONFIG_CPU_ABRT_EV7=y
+# CONFIG_CPU_BPREDICT_DISABLE is not set
+CONFIG_CPU_CACHE_V7=y
+CONFIG_CPU_CACHE_VIPT=y
+CONFIG_CPU_COPY_V6=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+CONFIG_CPU_HAS_ASID=y
+# CONFIG_CPU_ICACHE_DISABLE is not set
+CONFIG_CPU_PABRT_V7=y
+CONFIG_CPU_RMAP=y
+CONFIG_CPU_TLB_V7=y
+CONFIG_CPU_V7=y
+CONFIG_CRC16=y
+CONFIG_CRYPTO_AEAD=y
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_LZO=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
+CONFIG_CRYPTO_NULL2=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_WORKQUEUE=y
+CONFIG_DCACHE_WORD_ACCESS=y
+CONFIG_DEBUG_BCM_5301X=y
+CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_LL=y
+CONFIG_DEBUG_LL_INCLUDE="debug/8250.S"
+CONFIG_DEBUG_UART_8250=y
+# CONFIG_DEBUG_UART_8250_FLOW_CONTROL is not set
+CONFIG_DEBUG_UART_8250_SHIFT=0
+CONFIG_DEBUG_UART_PHYS=0x18000300
+CONFIG_DEBUG_UART_VIRT=0xf1000300
+CONFIG_DEBUG_UNCOMPRESS=y
+CONFIG_DEBUG_USER=y
+CONFIG_DTC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_EDAC_ATOMIC_SCRUB=y
+CONFIG_EDAC_SUPPORT=y
+CONFIG_FIXED_PHY=y
+CONFIG_FIX_EARLYCON_MEM=y
+CONFIG_FRAME_POINTER=y
+# CONFIG_FW_LOADER_USER_HELPER_FALLBACK is not set
+CONFIG_GENERIC_ALLOCATOR=y
+CONFIG_GENERIC_BUG=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
+CONFIG_GENERIC_EARLY_IOREMAP=y
+CONFIG_GENERIC_IDLE_POLL_SETUP=y
+CONFIG_GENERIC_IO=y
+CONFIG_GENERIC_IRQ_SHOW=y
+CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
+CONFIG_GENERIC_PCI_IOMAP=y
+CONFIG_GENERIC_PINCONF=y
+CONFIG_GENERIC_SCHED_CLOCK=y
+CONFIG_GENERIC_SMP_IDLE_THREAD=y
+CONFIG_GENERIC_STRNCPY_FROM_USER=y
+CONFIG_GENERIC_STRNLEN_USER=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIOLIB_IRQCHIP=y
+CONFIG_GPIO_74X164=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_HANDLE_DOMAIN_IRQ=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT_MAP=y
+# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
+CONFIG_HAVE_ARCH_AUDITSYSCALL=y
+CONFIG_HAVE_ARCH_BITREVERSE=y
+CONFIG_HAVE_ARCH_JUMP_LABEL=y
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_HAVE_ARCH_PFN_VALID=y
+CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
+CONFIG_HAVE_ARCH_TRACEHOOK=y
+CONFIG_HAVE_ARM_ARCH_TIMER=y
+CONFIG_HAVE_ARM_SCU=y
+CONFIG_HAVE_ARM_SMCCC=y
+CONFIG_HAVE_ARM_TWD=y
+# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
+CONFIG_HAVE_CBPF_JIT=y
+CONFIG_HAVE_CC_STACKPROTECTOR=y
+CONFIG_HAVE_CLK=y
+CONFIG_HAVE_CLK_PREPARE=y
+CONFIG_HAVE_CONTEXT_TRACKING=y
+CONFIG_HAVE_C_RECORDMCOUNT=y
+CONFIG_HAVE_DEBUG_KMEMLEAK=y
+CONFIG_HAVE_DMA_API_DEBUG=y
+CONFIG_HAVE_DMA_CONTIGUOUS=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_HAVE_IDE=y
+CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
+CONFIG_HAVE_MEMBLOCK=y
+CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
+CONFIG_HAVE_NET_DSA=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_OPTPROBES=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_HAVE_PERF_REGS=y
+CONFIG_HAVE_PERF_USER_STACK_DUMP=y
+CONFIG_HAVE_PROC_CPU=y
+CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
+CONFIG_HAVE_SMP=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
+CONFIG_HAVE_UID16=y
+CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
+CONFIG_HIGHMEM=y
+# CONFIG_HIGHPTE is not set
+CONFIG_HZ_FIXED=0
+CONFIG_HZ_PERIODIC=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_IOMMU_HELPER=y
+CONFIG_IRQCHIP=y
+CONFIG_IRQ_DOMAIN=y
+CONFIG_IRQ_DOMAIN_HIERARCHY=y
+CONFIG_IRQ_FORCED_THREADING=y
+CONFIG_IRQ_WORK=y
+CONFIG_LIBFDT=y
+CONFIG_LOCK_SPIN_ON_OWNER=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+# CONFIG_MDIO_BCM_IPROC is not set
+CONFIG_MDIO_BOARDINFO=y
+# CONFIG_MDIO_BUS_MUX_BCM_IPROC is not set
+CONFIG_MFD_SYSCON=y
+CONFIG_MIGHT_HAVE_CACHE_L2X0=y
+CONFIG_MIGHT_HAVE_PCI=y
+CONFIG_MODULES_USE_ELF_REL=y
+CONFIG_MTD_BCM47XXSFLASH=y
+CONFIG_MTD_BCM47XX_PARTS=y
+CONFIG_MTD_M25P80=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_BRCMNAND=y
+CONFIG_MTD_NAND_ECC=y
+CONFIG_MTD_PARSER_TRX=y
+# CONFIG_MTD_PHYSMAP_OF is not set
+CONFIG_MTD_SPI_NOR=y
+CONFIG_MTD_SPLIT_FIRMWARE=y
+CONFIG_MTD_SPLIT_SEAMA_FW=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_BEB_LIMIT=20
+CONFIG_MTD_UBI_BLOCK=y
+# CONFIG_MTD_UBI_FASTMAP is not set
+# CONFIG_MTD_UBI_GLUEBI is not set
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
+CONFIG_MULTI_IRQ_HANDLER=y
+CONFIG_MUTEX_SPIN_ON_OWNER=y
+CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_NET_FLOW_LIMIT=y
+CONFIG_NO_BOOTMEM=y
+CONFIG_NR_CPUS=2
+CONFIG_OF=y
+CONFIG_OF_ADDRESS=y
+CONFIG_OF_ADDRESS_PCI=y
+CONFIG_OF_EARLY_FLATTREE=y
+CONFIG_OF_FLATTREE=y
+CONFIG_OF_GPIO=y
+CONFIG_OF_IRQ=y
+CONFIG_OF_MDIO=y
+CONFIG_OF_NET=y
+CONFIG_OF_PCI=y
+CONFIG_OF_PCI_IRQ=y
+CONFIG_OF_RESERVED_MEM=y
+CONFIG_OLD_SIGACTION=y
+CONFIG_OLD_SIGSUSPEND3=y
+CONFIG_OUTER_CACHE=y
+CONFIG_OUTER_CACHE_SYNC=y
+CONFIG_PADATA=y
+CONFIG_PAGE_OFFSET=0xC0000000
+CONFIG_PCI=y
+CONFIG_PCIE_IPROC=y
+CONFIG_PCIE_IPROC_BCMA=y
+# CONFIG_PCIE_IPROC_PLATFORM is not set
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_DOMAINS_GENERIC=y
+CONFIG_PERF_USE_VMALLOC=y
+CONFIG_PGTABLE_LEVELS=2
+CONFIG_PHYLIB=y
+# CONFIG_PHY_BCM_NS_USB2 is not set
+# CONFIG_PHY_BCM_NS_USB3 is not set
+# CONFIG_PHY_BRCM_SATA is not set
+CONFIG_PINCTRL=y
+# CONFIG_PINCTRL_IPROC_GPIO is not set
+# CONFIG_PINCTRL_NS2_MUX is not set
+# CONFIG_PL310_ERRATA_588369 is not set
+# CONFIG_PL310_ERRATA_727915 is not set
+# CONFIG_PL310_ERRATA_753970 is not set
+# CONFIG_PL310_ERRATA_769419 is not set
+CONFIG_RATIONAL=y
+CONFIG_RCU_STALL_COMMON=y
+CONFIG_REGMAP=y
+CONFIG_REGMAP_MMIO=y
+CONFIG_RFS_ACCEL=y
+CONFIG_RPS=y
+CONFIG_RWSEM_SPIN_ON_OWNER=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+# CONFIG_SCHED_INFO is not set
+# CONFIG_SCSI_DMA is not set
+CONFIG_SERIAL_8250_FSL=y
+# CONFIG_SERIAL_AMBA_PL010 is not set
+# CONFIG_SERIAL_AMBA_PL011 is not set
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SMP=y
+CONFIG_SMP_ON_UP=y
+CONFIG_SPARSE_IRQ=y
+CONFIG_SPI=y
+CONFIG_SPI_BCM53XX=y
+CONFIG_SPI_BITBANG=y
+# CONFIG_SPI_CADENCE_QUADSPI is not set
+CONFIG_SPI_GPIO=y
+CONFIG_SPI_MASTER=y
+CONFIG_SRCU=y
+CONFIG_SWCONFIG=y
+CONFIG_SWCONFIG_B53=y
+# CONFIG_SWCONFIG_B53_MMAP_DRIVER is not set
+CONFIG_SWCONFIG_B53_PHY_DRIVER=y
+CONFIG_SWCONFIG_B53_PHY_FIXUP=y
+CONFIG_SWCONFIG_B53_SRAB_DRIVER=y
+CONFIG_SWIOTLB=y
+CONFIG_SWPHY=y
+CONFIG_SWP_EMULATE=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_THERMAL=y
+CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
+CONFIG_THERMAL_GOV_STEP_WISE=y
+CONFIG_THERMAL_OF=y
+# CONFIG_THUMB2_KERNEL is not set
+CONFIG_TICK_CPU_ACCOUNTING=y
+CONFIG_TREE_RCU=y
+CONFIG_UBIFS_FS=y
+# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set
+CONFIG_UBIFS_FS_LZO=y
+CONFIG_UBIFS_FS_ZLIB=y
+CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
+CONFIG_USB_SUPPORT=y
+CONFIG_USE_OF=y
+CONFIG_VECTORS_BASE=0xffff0000
+# CONFIG_VFP is not set
+CONFIG_WATCHDOG_CORE=y
+CONFIG_XPS=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_BCJ=y
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_ZLIB_INFLATE=y
--- /dev/null
+From 2460266f21f140936e627f28f28d1a4f30887ae9 Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal@milecki.pl>
+Date: Fri, 6 Oct 2017 10:52:35 +0200
+Subject: [PATCH] ARM: dts: BCM5301X: Specify USB ports for USB LED of Luxul
+ XWR-1200
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+This info can be used by operating system to setup LED behavior.
+
+Reported-by: Dan Haab <dhaab@luxul.com>
+Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
+Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
+---
+ arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts | 3 ++-
+ 1 file changed, 2 insertions(+), 1 deletion(-)
+
+--- a/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts
++++ b/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts
+@@ -57,7 +57,8 @@
+ usb {
+ label = "bcm53xx:green:usb";
+ gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
+- linux,default-trigger = "none";
++ trigger-sources = <&ohci_port2>, <&ehci_port2>;
++ linux,default-trigger = "usbport";
+ };
+
+ status {
--- /dev/null
+From 1f4b0d5596d2e3ea8e953d578ab8444ce860d35d Mon Sep 17 00:00:00 2001
+From: Dan Haab <dhaab@luxul.com>
+Date: Mon, 9 Oct 2017 09:46:22 -0600
+Subject: [PATCH] ARM: dts: BCM5301X: Add DT for Luxul XBR-4500
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+This is BCM47094 (AKA BCM4709C0) based router with ports-on-the-front
+board design.
+
+Signed-off-by: Dan Haab <dhaab@luxul.com>
+Acked-by: Rafał Miłecki <rafal@milecki.pl>
+Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
+---
+ arch/arm/boot/dts/Makefile | 1 +
+ arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts | 63 +++++++++++++++++++++++++++
+ 2 files changed, 64 insertions(+)
+ create mode 100644 arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts
+
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -101,6 +101,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
+ bcm4709-tplink-archer-c9-v1.dtb \
+ bcm47094-dlink-dir-885l.dtb \
+ bcm47094-linksys-panamera.dtb \
++ bcm47094-luxul-xbr-4500.dtb \
+ bcm47094-luxul-xwr-3100.dtb \
+ bcm47094-netgear-r8500.dtb \
+ bcm94708.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts
+@@ -0,0 +1,63 @@
++/*
++ * Copyright (C) 2017 Luxul Inc.
++ *
++ * Licensed under the ISC license.
++ */
++
++/dts-v1/;
++
++#include "bcm4708.dtsi"
++#include "bcm5301x-nand-cs0-bch8.dtsi"
++
++/ {
++ compatible = "luxul,xbr-4500-v1", "brcm,bcm47094", "brcm,bcm4708";
++ model = "Luxul XBR-4500 V1";
++
++ chosen {
++ bootargs = "earlycon";
++ };
++
++ memory {
++ reg = <0x00000000 0x08000000
++ 0x88000000 0x18000000>;
++ };
++
++ leds {
++ compatible = "gpio-leds";
++
++ status {
++ label = "bcm53xx:green:status";
++ gpios = <&chipcommon 20 GPIO_ACTIVE_HIGH>;
++ linux,default-trigger = "timer";
++ };
++
++ usb3 {
++ label = "bcm53xx:green:usb3";
++ gpios = <&chipcommon 19 GPIO_ACTIVE_HIGH>;
++ trigger-sources = <&ohci_port1>, <&ehci_port1>,
++ <&xhci_port1>;
++ linux,default-trigger = "usbport";
++ };
++
++ };
++
++ gpio-keys {
++ compatible = "gpio-keys";
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ restart {
++ label = "Reset";
++ linux,code = <KEY_RESTART>;
++ gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
++ };
++ };
++};
++
++&usb3 {
++ vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
++};
++
++&spi_nor {
++ status = "okay";
++};
--- /dev/null
+From 65f78c4c41a9b9a7637e1dda2d5e41cf26ea971c Mon Sep 17 00:00:00 2001
+From: Dan Haab <dhaab@luxul.com>
+Date: Mon, 9 Oct 2017 09:46:23 -0600
+Subject: [PATCH] ARM: dts: BCM5301X: Add DT for Luxul ABR-4500
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+This is BCM47094 (AKA BCM4709C0) based router with rear-facing ports
+board design.
+
+Signed-off-by: Dan Haab <dhaab@luxul.com>
+Acked-by: Rafał Miłecki <rafal@milecki.pl>
+Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
+---
+ arch/arm/boot/dts/Makefile | 1 +
+ arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts | 63 +++++++++++++++++++++++++++
+ 2 files changed, 64 insertions(+)
+ create mode 100644 arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts
+
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -101,6 +101,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
+ bcm4709-tplink-archer-c9-v1.dtb \
+ bcm47094-dlink-dir-885l.dtb \
+ bcm47094-linksys-panamera.dtb \
++ bcm47094-luxul-abr-4500.dtb \
+ bcm47094-luxul-xbr-4500.dtb \
+ bcm47094-luxul-xwr-3100.dtb \
+ bcm47094-netgear-r8500.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts
+@@ -0,0 +1,63 @@
++/*
++ * Copyright (C) 2017 Luxul Inc.
++ *
++ * Licensed under the ISC license.
++ */
++
++/dts-v1/;
++
++#include "bcm4708.dtsi"
++#include "bcm5301x-nand-cs0-bch8.dtsi"
++
++/ {
++ compatible = "luxul,abr-4500-v1", "brcm,bcm47094", "brcm,bcm4708";
++ model = "Luxul ABR-4500 V1";
++
++ chosen {
++ bootargs = "earlycon";
++ };
++
++ memory {
++ reg = <0x00000000 0x08000000
++ 0x88000000 0x18000000>;
++ };
++
++ leds {
++ compatible = "gpio-leds";
++
++ status {
++ label = "bcm53xx:green:status";
++ gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "timer";
++ };
++
++ usb3 {
++ label = "bcm53xx:green:usb3";
++ gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
++ trigger-sources = <&ohci_port1>, <&ehci_port1>,
++ <&xhci_port1>;
++ linux,default-trigger = "usbport";
++ };
++
++ };
++
++ gpio-keys {
++ compatible = "gpio-keys";
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ restart {
++ label = "Reset";
++ linux,code = <KEY_RESTART>;
++ gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
++ };
++ };
++};
++
++&usb3 {
++ vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
++};
++
++&spi_nor {
++ status = "okay";
++};
--- /dev/null
+From 0aa052ce1c3340850a7e5980b6d24b3ea5779591 Mon Sep 17 00:00:00 2001
+From: Dan Haab <dhaab@luxul.com>
+Date: Mon, 9 Oct 2017 09:46:59 -0600
+Subject: [PATCH] ARM: dts: BCM53573: Add DT for Luxul XAP-810
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+This is BCM53573 WiSoC based access point with an extra BCM43217 chipset
+used for 2.4 GHz.
+
+Signed-off-by: Dan Haab <dhaab@luxul.com>
+Acked-by: Rafał Miłecki <rafal@milecki.pl>
+Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
+---
+ arch/arm/boot/dts/Makefile | 1 +
+ arch/arm/boot/dts/bcm47189-luxul-xap-810.dts | 87 ++++++++++++++++++++++++++++
+ 2 files changed, 88 insertions(+)
+ create mode 100644 arch/arm/boot/dts/bcm47189-luxul-xap-810.dts
+
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -111,6 +111,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
+ bcm953012hr.dtb \
+ bcm953012k.dtb
+ dtb-$(CONFIG_ARCH_BCM_53573) += \
++ bcm47189-luxul-xap-810.dtb \
+ bcm47189-tenda-ac9.dtb \
+ bcm947189acdbmr.dtb
+ dtb-$(CONFIG_ARCH_BCM_63XX) += \
+--- /dev/null
++++ b/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts
+@@ -0,0 +1,87 @@
++/*
++ * Copyright 2017 Luxul Inc.
++ *
++ * Licensed under the ISC license.
++ */
++
++/dts-v1/;
++
++#include "bcm53573.dtsi"
++
++/ {
++ compatible = "luxul,xap-810-v1", "brcm,bcm47189", "brcm,bcm53573";
++ model = "Luxul XAP-810 V1";
++
++ chosen {
++ bootargs = "earlycon";
++ };
++
++ memory {
++ reg = <0x00000000 0x08000000>;
++ };
++
++ leds {
++ compatible = "gpio-leds";
++
++ 5ghz {
++ label = "bcm53xx:blue:5ghz";
++ gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
++ linux,default-trigger = "default-off";
++ };
++
++ system {
++ label = "bcm53xx:green:system";
++ gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>;
++ linux,default-trigger = "timer";
++ };
++ };
++
++ pcie0_leds {
++ compatible = "gpio-leds";
++
++ 2ghz {
++ label = "bcm53xx:blue:2ghz";
++ gpios = <&pcie0_chipcommon 3 GPIO_ACTIVE_HIGH>;
++ linux,default-trigger = "default-off";
++ };
++ };
++
++ gpio-keys {
++ compatible = "gpio-keys";
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ restart {
++ label = "Reset";
++ linux,code = <KEY_RESTART>;
++ gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
++ };
++ };
++};
++
++&pcie0 {
++ ranges = <0x00000000 0 0 0 0 0x00100000>;
++ #address-cells = <3>;
++ #size-cells = <2>;
++
++ bridge@0,0,0 {
++ reg = <0x0000 0 0 0 0>;
++ ranges = <0x00000000 0 0 0 0 0 0 0x00100000>;
++ #address-cells = <3>;
++ #size-cells = <2>;
++
++ wifi@0,1,0 {
++ reg = <0x0000 0 0 0 0>;
++ ranges = <0x00000000 0 0 0 0x00100000>;
++ #address-cells = <1>;
++ #size-cells = <1>;
++
++ pcie0_chipcommon: chipcommon@0 {
++ reg = <0 0x1000>;
++
++ gpio-controller;
++ #gpio-cells = <2>;
++ };
++ };
++ };
++};
--- /dev/null
+From 7030ea600d560026b91726f2eb79c856b813afa9 Mon Sep 17 00:00:00 2001
+From: Dan Haab <dhaab@luxul.com>
+Date: Mon, 9 Oct 2017 09:47:00 -0600
+Subject: [PATCH] ARM: dts: BCM53573: Add DT for Luxul XAP-1440
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+This is BCM53573 WiSoC based outdoor access point with an extra BCM43217
+chipset used for 2.4 GHz.
+
+Signed-off-by: Dan Haab <dhaab@luxul.com>
+Acked-by: Rafał Miłecki <rafal@milecki.pl>
+Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
+---
+ arch/arm/boot/dts/Makefile | 1 +
+ arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts | 50 +++++++++++++++++++++++++++
+ 2 files changed, 51 insertions(+)
+ create mode 100644 arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts
+
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -111,6 +111,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
+ bcm953012hr.dtb \
+ bcm953012k.dtb
+ dtb-$(CONFIG_ARCH_BCM_53573) += \
++ bcm47189-luxul-xap-1440.dtb \
+ bcm47189-luxul-xap-810.dtb \
+ bcm47189-tenda-ac9.dtb \
+ bcm947189acdbmr.dtb
+--- /dev/null
++++ b/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts
+@@ -0,0 +1,50 @@
++/*
++ * Copyright 2017 Luxul Inc.
++ *
++ * Licensed under the ISC license.
++ */
++
++/dts-v1/;
++
++#include "bcm53573.dtsi"
++
++/ {
++ compatible = "luxul,xap-1440-v1", "brcm,bcm47189", "brcm,bcm53573";
++ model = "Luxul XAP-1440 V1";
++
++ chosen {
++ bootargs = "earlycon";
++ };
++
++ memory {
++ reg = <0x00000000 0x08000000>;
++ };
++
++ leds {
++ compatible = "gpio-leds";
++
++ wlan {
++ label = "bcm53xx:blue:wlan";
++ gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "default-off";
++ };
++
++ system {
++ label = "bcm53xx:green:system";
++ gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "timer";
++ };
++ };
++
++ gpio-keys {
++ compatible = "gpio-keys";
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ restart {
++ label = "Reset";
++ linux,code = <KEY_RESTART>;
++ gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
++ };
++ };
++};
--- /dev/null
+--- a/arch/arm/boot/dts/bcm5301x-nand-cs0.dtsi
++++ b/arch/arm/boot/dts/bcm5301x-nand-cs0.dtsi
+@@ -13,6 +13,8 @@
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
++
++ linux,part-probe = "ofpart", "bcm47xxpart";
+ };
+ };
+ };
--- /dev/null
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal@milecki.pl>
+Date: Sat, 1 Oct 2016 22:54:48 +0200
+Subject: [PATCH] usb: xhci: add support for performing fake doorbell
+
+Broadcom's Northstar XHCI controllers seem to need a special start
+procedure to work correctly. There isn't any official documentation of
+this, the problem is that controller doesn't detect any connected
+devices with default setup. Moreover connecting USB device to controller
+that doesn't run properly can cause SoC's watchdog issues.
+
+A workaround that was successfully tested on multiple devices is to
+perform a fake doorbell. This patch adds code for doing this and enables
+it on BCM4708 family.
+---
+ drivers/usb/host/xhci-plat.c | 6 +++++
+ drivers/usb/host/xhci.c | 63 +++++++++++++++++++++++++++++++++++++++++---
+ drivers/usb/host/xhci.h | 1 +
+ 3 files changed, 67 insertions(+), 3 deletions(-)
+
+--- a/drivers/usb/host/xhci-plat.c
++++ b/drivers/usb/host/xhci-plat.c
+@@ -67,12 +67,18 @@ static int xhci_priv_resume_quirk(struct
+
+ static void xhci_plat_quirks(struct device *dev, struct xhci_hcd *xhci)
+ {
++ struct platform_device *pdev = to_platform_device(dev);
++ struct device_node *node = pdev->dev.of_node;
++
+ /*
+ * As of now platform drivers don't provide MSI support so we ensure
+ * here that the generic code does not try to make a pci_dev from our
+ * dev struct in order to setup MSI
+ */
+ xhci->quirks |= XHCI_PLAT;
++
++ if (node && of_machine_is_compatible("brcm,bcm4708"))
++ xhci->quirks |= XHCI_FAKE_DOORBELL;
+ }
+
+ /* called during probe() after chip reset completes */
+--- a/drivers/usb/host/xhci.c
++++ b/drivers/usb/host/xhci.c
+@@ -153,6 +153,49 @@ int xhci_start(struct xhci_hcd *xhci)
+ return ret;
+ }
+
++/**
++ * xhci_fake_doorbell - Perform a fake doorbell on a specified slot
++ *
++ * Some controllers require a fake doorbell to start correctly. Without that
++ * they simply don't detect any devices.
++ */
++static int xhci_fake_doorbell(struct xhci_hcd *xhci, int slot_id)
++{
++ u32 temp;
++
++ /* Alloc a virt device for that slot */
++ if (!xhci_alloc_virt_device(xhci, slot_id, NULL, GFP_NOIO)) {
++ xhci_warn(xhci, "Could not allocate xHCI USB device data structures\n");
++ return -ENOMEM;
++ }
++
++ /* Ring fake doorbell for slot_id ep 0 */
++ xhci_ring_ep_doorbell(xhci, slot_id, 0, 0);
++ usleep_range(1000, 1500);
++
++ /* Read the status to check if HSE is set or not */
++ temp = readl(&xhci->op_regs->status);
++
++ /* Clear HSE if set */
++ if (temp & STS_FATAL) {
++ xhci_dbg(xhci, "HSE problem detected, status: 0x%08x\n", temp);
++ temp &= ~0x1fff;
++ temp |= STS_FATAL;
++ writel(temp, &xhci->op_regs->status);
++ usleep_range(1000, 1500);
++ readl(&xhci->op_regs->status);
++ }
++
++ /* Free virt device */
++ xhci_free_virt_device(xhci, slot_id);
++
++ /* We're done if controller is already running */
++ if (readl(&xhci->op_regs->command) & CMD_RUN)
++ return 0;
++
++ return xhci_start(xhci);
++}
++
+ /*
+ * Reset a halted HC.
+ *
+@@ -536,10 +579,20 @@ static int xhci_init(struct usb_hcd *hcd
+
+ static int xhci_run_finished(struct xhci_hcd *xhci)
+ {
+- if (xhci_start(xhci)) {
+- xhci_halt(xhci);
+- return -ENODEV;
++ int err;
++
++ err = xhci_start(xhci);
++ if (err) {
++ err = -ENODEV;
++ goto err_halt;
+ }
++
++ if (xhci->quirks & XHCI_FAKE_DOORBELL) {
++ err = xhci_fake_doorbell(xhci, 1);
++ if (err)
++ goto err_halt;
++ }
++
+ xhci->shared_hcd->state = HC_STATE_RUNNING;
+ xhci->cmd_ring_state = CMD_RING_STATE_RUNNING;
+
+@@ -549,6 +602,10 @@ static int xhci_run_finished(struct xhci
+ xhci_dbg_trace(xhci, trace_xhci_dbg_init,
+ "Finished xhci_run for USB3 roothub");
+ return 0;
++
++err_halt:
++ xhci_halt(xhci);
++ return err;
+ }
+
+ /*
+--- a/drivers/usb/host/xhci.h
++++ b/drivers/usb/host/xhci.h
+@@ -1830,6 +1830,7 @@ struct xhci_hcd {
+ #define XHCI_LIMIT_ENDPOINT_INTERVAL_7 (1 << 26)
+ /* Reserved. It was XHCI_U2_DISABLE_WAKE */
+ #define XHCI_ASMEDIA_MODIFY_FLOWCONTROL (1 << 28)
++#define XHCI_FAKE_DOORBELL (1 << 29)
+
+ unsigned int num_active_eps;
+ unsigned int limit_active_eps;
--- /dev/null
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal@milecki.pl>
+Date: Fri, 29 Dec 2017 14:44:09 +0100
+Subject: [PATCH] spi: bcm53xx: simplify reading SPI data
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+This commit makes transfer function use spi_transfer_is_last to
+determine if currently processed transfer is the last one. Thanks to
+that we finally set hardware registers properly and it makes controller
+behave the way it's expected to.
+
+This allows simplifying read function which can now simply start reading
+from the slot 0 instead of the last saved offset. It has been
+successfully tested using spi_write_then_read.
+
+Moreover this change fixes handling messages with two writing transfers.
+It's important for SPI flash devices as their drivers commonly use one
+transfer for a command and another one for data.
+
+Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
+---
+ drivers/spi/spi-bcm53xx.c | 26 ++++++++++----------------
+ 1 file changed, 10 insertions(+), 16 deletions(-)
+
+--- a/drivers/spi/spi-bcm53xx.c
++++ b/drivers/spi/spi-bcm53xx.c
+@@ -27,8 +27,6 @@ struct bcm53xxspi {
+ struct bcma_device *core;
+ struct spi_master *master;
+ void __iomem *mmio_base;
+-
+- size_t read_offset;
+ bool bspi; /* Boot SPI mode with memory mapping */
+ };
+
+@@ -172,8 +170,6 @@ static void bcm53xxspi_buf_write(struct
+
+ if (!cont)
+ bcm53xxspi_write(b53spi, B53SPI_MSPI_WRITE_LOCK, 0);
+-
+- b53spi->read_offset = len;
+ }
+
+ static void bcm53xxspi_buf_read(struct bcm53xxspi *b53spi, u8 *r_buf,
+@@ -182,10 +178,10 @@ static void bcm53xxspi_buf_read(struct b
+ u32 tmp;
+ int i;
+
+- for (i = 0; i < b53spi->read_offset + len; i++) {
++ for (i = 0; i < len; i++) {
+ tmp = B53SPI_CDRAM_CONT | B53SPI_CDRAM_PCS_DISABLE_ALL |
+ B53SPI_CDRAM_PCS_DSCK;
+- if (!cont && i == b53spi->read_offset + len - 1)
++ if (!cont && i == len - 1)
+ tmp &= ~B53SPI_CDRAM_CONT;
+ tmp &= ~0x1;
+ /* Command Register File */
+@@ -194,8 +190,7 @@ static void bcm53xxspi_buf_read(struct b
+
+ /* Set queue pointers */
+ bcm53xxspi_write(b53spi, B53SPI_MSPI_NEWQP, 0);
+- bcm53xxspi_write(b53spi, B53SPI_MSPI_ENDQP,
+- b53spi->read_offset + len - 1);
++ bcm53xxspi_write(b53spi, B53SPI_MSPI_ENDQP, len - 1);
+
+ if (cont)
+ bcm53xxspi_write(b53spi, B53SPI_MSPI_WRITE_LOCK, 1);
+@@ -214,13 +209,11 @@ static void bcm53xxspi_buf_read(struct b
+ bcm53xxspi_write(b53spi, B53SPI_MSPI_WRITE_LOCK, 0);
+
+ for (i = 0; i < len; ++i) {
+- int offset = b53spi->read_offset + i;
++ u16 reg = B53SPI_MSPI_RXRAM + 4 * (1 + i * 2);
+
+ /* Data stored in the transmit register file LSB */
+- r_buf[i] = (u8)bcm53xxspi_read(b53spi, B53SPI_MSPI_RXRAM + 4 * (1 + offset * 2));
++ r_buf[i] = (u8)bcm53xxspi_read(b53spi, reg);
+ }
+-
+- b53spi->read_offset = 0;
+ }
+
+ static int bcm53xxspi_transfer_one(struct spi_master *master,
+@@ -238,7 +231,8 @@ static int bcm53xxspi_transfer_one(struc
+ left = t->len;
+ while (left) {
+ size_t to_write = min_t(size_t, 16, left);
+- bool cont = left - to_write > 0;
++ bool cont = !spi_transfer_is_last(master, t) ||
++ left - to_write > 0;
+
+ bcm53xxspi_buf_write(b53spi, buf, to_write, cont);
+ left -= to_write;
+@@ -250,9 +244,9 @@ static int bcm53xxspi_transfer_one(struc
+ buf = (u8 *)t->rx_buf;
+ left = t->len;
+ while (left) {
+- size_t to_read = min_t(size_t, 16 - b53spi->read_offset,
+- left);
+- bool cont = left - to_read > 0;
++ size_t to_read = min_t(size_t, 16, left);
++ bool cont = !spi_transfer_is_last(master, t) ||
++ left - to_read > 0;
+
+ bcm53xxspi_buf_read(b53spi, buf, to_read, cont);
+ left -= to_read;
--- /dev/null
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal@milecki.pl>
+Date: Wed, 24 Sep 2014 22:14:07 +0200
+Subject: [PATCH] ARM: BCM5301X: Disable MMU and Dcache during decompression
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Broadcom devices have broken CFE (bootloader) that leaves hardware in an
+invalid state. It causes problems with booting Linux. On Northstar
+devices kernel was randomly hanging in ~25% of tries during early init.
+Hangs used to happen at random places in the start_kernel. On BCM53573
+kernel doesn't even seem to start booting.
+
+To workaround this problem we need to do following very early:
+1) Clear 2 following bits in the SCTLR register:
+#define CR_M (1 << 0) /* MMU enable */
+#define CR_C (1 << 2) /* Dcache enable */
+2) Flush the whole D-cache
+3) Disable L2 cache
+
+Unfortunately this patch is not upstreamable as it does above things
+unconditionally. We can't check if we are running on Broadcom platform
+in any safe way and doing such hacks with ARCH_MULTI_V7 is unacceptable
+as it could break other devices support.
+
+Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
+---
+
+--- a/arch/arm/boot/compressed/Makefile
++++ b/arch/arm/boot/compressed/Makefile
+@@ -32,6 +32,11 @@ ifeq ($(CONFIG_ARCH_ACORN),y)
+ OBJS += ll_char_wr.o font.o
+ endif
+
++ifeq ($(CONFIG_ARCH_BCM_5301X),y)
++OBJS += head-bcm_5301x-mpcore.o
++OBJS += cache-v7-min.o
++endif
++
+ ifeq ($(CONFIG_ARCH_SA1100),y)
+ OBJS += head-sa1100.o
+ endif
+--- /dev/null
++++ b/arch/arm/boot/compressed/head-bcm_5301x-mpcore.S
+@@ -0,0 +1,37 @@
++/*
++ *
++ * Platform specific tweaks. This is merged into head.S by the linker.
++ *
++ */
++
++#include <linux/linkage.h>
++#include <asm/assembler.h>
++#include <asm/cp15.h>
++
++ .section ".start", "ax"
++
++/*
++ * This code section is spliced into the head code by the linker
++ */
++
++__plat_uncompress_start:
++
++ @ Preserve r8/r7 i.e. kernel entry values
++ mov r12, r8
++
++ @ Clear MMU enable and Dcache enable bits
++ mrc p15, 0, r0, c1, c0, 0 @ Read SCTLR
++ bic r0, #CR_C|CR_M
++ mcr p15, 0, r0, c1, c0, 0 @ Write SCTLR
++ nop
++
++ @ Call the cache invalidation routine
++ bl v7_flush_dcache_all
++ nop
++ mov r0,#0
++ ldr r3, =0x19022000 @ L2 cache controller, control reg
++ str r0, [r3, #0x100] @ Disable L2 cache
++ nop
++
++ @ Restore
++ mov r8, r12
+--- a/arch/arm/boot/compressed/cache-v7-min.S
++++ b/arch/arm/boot/compressed/cache-v7-min.S
+@@ -12,6 +12,7 @@
+
+ #include <linux/linkage.h>
+ #include <linux/init.h>
++#include <asm/assembler.h>
+
+ __INIT
+
+@@ -63,7 +64,7 @@ loop2:
+ ARM( orr r11, r11, r9, lsl r2 ) @ factor index number into r11
+ THUMB( lsl r6, r9, r2 )
+ THUMB( orr r11, r11, r6 ) @ factor index number into r11
+- mcr p15, 0, r11, c7, c14, 2 @ clean & invalidate by set/way
++ mcr p15, 0, r11, c7, c6, 2 @ clean & invalidate by set/way
+ subs r9, r9, #1 @ decrement the index
+ bge loop2
+ subs r4, r4, #1 @ decrement the way
--- /dev/null
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <zajec5@gmail.com>
+Subject: [PATCH] ARM: BCM5301X: Add DT for Netgear R7900
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
+---
+
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -97,6 +97,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
+ bcm4709-buffalo-wxr-1900dhp.dtb \
+ bcm4709-linksys-ea9200.dtb \
+ bcm4709-netgear-r7000.dtb \
++ bcm4709-netgear-r7900.dtb \
+ bcm4709-netgear-r8000.dtb \
+ bcm4709-tplink-archer-c9-v1.dtb \
+ bcm47094-dlink-dir-885l.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/bcm4709-netgear-r7900.dts
+@@ -0,0 +1,42 @@
++/*
++ * Broadcom BCM470X / BCM5301X ARM platform code.
++ * DTS for Netgear R7900
++ *
++ * Copyright (C) 2016 Rafał Miłecki <zajec5@gmail.com>
++ *
++ * Licensed under the GNU/GPL. See COPYING for details.
++ */
++
++/dts-v1/;
++
++#include "bcm4709.dtsi"
++#include "bcm5301x-nand-cs0-bch8.dtsi"
++
++/ {
++ compatible = "netgear,r7900", "brcm,bcm4709", "brcm,bcm4708";
++ model = "Netgear R7900";
++
++ chosen {
++ bootargs = "console=ttyS0,115200";
++ };
++
++ memory {
++ reg = <0x00000000 0x08000000
++ 0x88000000 0x08000000>;
++ };
++
++ axi@18000000 {
++ usb3@23000 {
++ reg = <0x00023000 0x1000>;
++
++ #address-cells = <1>;
++ #size-cells = <1>;
++
++ vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
++ };
++ };
++};
++
++&uart0 {
++ status = "okay";
++};
--- /dev/null
+From: Felix Fietkau <nbd@nbd.name>
+Subject: [PATCH] ARM: BCM5301X: Add power button for Buffalo WZR-1750DHP
+
+Signed-off-by: Felix Fietkau <nbd@nbd.name>
+---
+--- a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
++++ b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
+@@ -102,6 +102,12 @@
+ #address-cells = <1>;
+ #size-cells = <0>;
+
++ power {
++ label = "Power";
++ linux,code = <KEY_POWER>;
++ gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
++ };
++
+ restart {
+ label = "Reset";
+ linux,code = <KEY_RESTART>;
--- /dev/null
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal@milecki.pl>
+Subject: [PATCH] ARM: dts: BCM5301X: Add serial= to the bootargs
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+It's enough to have proper stdout-path for getting serial working but
+for some reason LEDE doesn't offer "Please press Enter to activate this
+console." unless ttyS0 is specified.
+
+This is a workaround to get serial working in LEDE.
+
+Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
+---
+
+--- a/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts
++++ b/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts
+@@ -13,7 +13,7 @@
+ model = "TP-LINK Archer C5 V2";
+
+ chosen {
+- bootargs = "earlycon";
++ bootargs = "console=ttyS0,115200 earlycon";
+ };
+
+ memory {
+--- a/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts
++++ b/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts
+@@ -14,7 +14,7 @@
+ model = "Luxul ABR-4500 V1";
+
+ chosen {
+- bootargs = "earlycon";
++ bootargs = "console=ttyS0,115200 earlycon";
+ };
+
+ memory {
+--- a/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts
++++ b/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts
+@@ -14,7 +14,7 @@
+ model = "Luxul XBR-4500 V1";
+
+ chosen {
+- bootargs = "earlycon";
++ bootargs = "console=ttyS0,115200 earlycon";
+ };
+
+ memory {
+--- a/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts
++++ b/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts
+@@ -13,7 +13,7 @@
+ model = "Luxul XAP-1440 V1";
+
+ chosen {
+- bootargs = "earlycon";
++ bootargs = "console=ttyS0,115200 earlycon";
+ };
+
+ memory {
+--- a/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts
++++ b/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts
+@@ -13,7 +13,7 @@
+ model = "Luxul XAP-810 V1";
+
+ chosen {
+- bootargs = "earlycon";
++ bootargs = "console=ttyS0,115200 earlycon";
+ };
+
+ memory {
--- /dev/null
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <zajec5@gmail.com>
+Subject: [PATCH] mtd: spi-nor: detect JEDEC incompatible w25q128 using 0x90
+ command
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Some w25q128 chipsets don't support RDID (0x9f) command, they reply with
+0xff-s only. To suppose such flashes fallback to the 0x90 command.
+
+Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
+---
+
+--- a/drivers/mtd/spi-nor/spi-nor.c
++++ b/drivers/mtd/spi-nor/spi-nor.c
+@@ -1205,6 +1205,18 @@ static const struct flash_info *spi_nor_
+ }
+ dev_err(nor->dev, "unrecognized JEDEC id bytes: %02x, %02x, %02x\n",
+ id[0], id[1], id[2]);
++
++ tmp = nor->read_reg(nor, 0x90, id, SPI_NOR_MAX_ID_LEN);
++ if (tmp < 0) {
++ dev_dbg(nor->dev, " error %d reading JEDEC ID\n", tmp);
++ return ERR_PTR(tmp);
++ }
++ dev_info(nor->dev, "using Read Manufacturer / Device ID command (0x%02x) returned %02x %02x\n",
++ 0x90, id[0x03], id[0x04]);
++ if (id[0x03] == 0xef && id[0x04] == 0x17) {
++ return spi_nor_match_id("w25q128");
++ }
++
+ return ERR_PTR(-ENODEV);
+ }
+
--- /dev/null
+From 2a2af518266a29323cf30c3f9ba9ef2ceb1dd84b Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <zajec5@gmail.com>
+Date: Thu, 16 Oct 2014 20:52:16 +0200
+Subject: [PATCH] UBI: Detect EOF mark and erase all remaining blocks
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
+---
+ drivers/mtd/ubi/attach.c | 5 +++++
+ drivers/mtd/ubi/io.c | 4 ++++
+ drivers/mtd/ubi/ubi.h | 1 +
+ 3 files changed, 10 insertions(+)
+
+--- a/drivers/mtd/ubi/attach.c
++++ b/drivers/mtd/ubi/attach.c
+@@ -95,6 +95,9 @@ static int self_check_ai(struct ubi_devi
+ #define AV_ADD BIT(1)
+ #define AV_FIND_OR_ADD (AV_FIND | AV_ADD)
+
++/* Set on finding block with 0xdeadc0de, indicates erasing all blocks behind */
++bool erase_all_next;
++
+ /**
+ * find_or_add_av - internal function to find a volume, add a volume or do
+ * both (find and add if missing).
+@@ -1592,6 +1595,8 @@ int ubi_attach(struct ubi_device *ubi, i
+ if (!ai)
+ return -ENOMEM;
+
++ erase_all_next = false;
++
+ #ifdef CONFIG_MTD_UBI_FASTMAP
+ /* On small flash devices we disable fastmap in any case. */
+ if ((int)mtd_div_by_eb(ubi->mtd->size, ubi->mtd) <= UBI_FM_MAX_START) {
+--- a/drivers/mtd/ubi/io.c
++++ b/drivers/mtd/ubi/io.c
+@@ -759,6 +759,10 @@ int ubi_io_read_ec_hdr(struct ubi_device
+ }
+
+ magic = be32_to_cpu(ec_hdr->magic);
++ if (magic == 0xdeadc0de)
++ erase_all_next = true;
++ if (erase_all_next)
++ return read_err ? UBI_IO_FF_BITFLIPS : UBI_IO_FF;
+ if (magic != UBI_EC_HDR_MAGIC) {
+ if (mtd_is_eccerr(read_err))
+ return UBI_IO_BAD_HDR_EBADMSG;
+--- a/drivers/mtd/ubi/ubi.h
++++ b/drivers/mtd/ubi/ubi.h
+@@ -822,6 +822,7 @@ extern struct mutex ubi_devices_mutex;
+ extern struct blocking_notifier_head ubi_notifiers;
+
+ /* attach.c */
++extern bool erase_all_next;
+ struct ubi_ainf_peb *ubi_alloc_aeb(struct ubi_attach_info *ai, int pnum,
+ int ec);
+ void ubi_free_aeb(struct ubi_attach_info *ai, struct ubi_ainf_peb *aeb);
--- /dev/null
+From 4abdde3ad6bc0b3b157c4bf6ec0bf139d11d07e8 Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <zajec5@gmail.com>
+Date: Wed, 13 May 2015 14:13:28 +0200
+Subject: [PATCH] b53: add hacky CPU port fixes for devices not using port 5
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
+---
+ drivers/net/phy/b53/b53_common.c | 6 ++++++
+ 1 file changed, 6 insertions(+)
+
+--- a/drivers/net/phy/b53/b53_common.c
++++ b/drivers/net/phy/b53/b53_common.c
+@@ -28,6 +28,7 @@
+ #include <linux/of.h>
+ #include <linux/of_net.h>
+ #include <linux/platform_data/b53.h>
++#include <linux/of.h>
+
+ #include "b53_regs.h"
+ #include "b53_priv.h"
+@@ -1579,6 +1580,28 @@ static int b53_switch_init(struct b53_de
+ return ret;
+ }
+
++ /* Set correct CPU port */
++ if (of_machine_is_compatible("asus,rt-ac87u"))
++ sw_dev->cpu_port = 7;
++ else if (of_machine_is_compatible("netgear,r7900"))
++ sw_dev->cpu_port = 8;
++ else if (of_machine_is_compatible("netgear,r8000"))
++ sw_dev->cpu_port = 8;
++ else if (of_machine_is_compatible("netgear,r8500"))
++ sw_dev->cpu_port = 8;
++
++ /* Enable extra ports */
++ if (of_machine_is_compatible("tenda,ac9"))
++ dev->enabled_ports |= BIT(5);
++
++ /*
++ * Workaround for devices using port 8 (connected to the 3rd iface).
++ * For some reason it doesn't work (no packets on eth2).
++ */
++ if (of_machine_is_compatible("netgear,r7900") ||
++ of_machine_is_compatible("netgear,r8000"))
++ sw_dev->cpu_port = 5;
++
+ dev->enabled_ports |= BIT(sw_dev->cpu_port);
+ sw_dev->ports = fls(dev->enabled_ports);
+
--- /dev/null
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal@milecki.pl>
+Subject: [PATCH] mtd: bcm47xxpart: add device specific workarounds
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
+---
+
+--- a/drivers/mtd/bcm47xxpart.c
++++ b/drivers/mtd/bcm47xxpart.c
+@@ -15,6 +15,7 @@
+ #include <linux/slab.h>
+ #include <linux/mtd/mtd.h>
+ #include <linux/mtd/partitions.h>
++#include <linux/of.h>
+
+ #include <uapi/linux/magic.h>
+
+@@ -134,6 +135,36 @@ static int bcm47xxpart_parse(struct mtd_
+ break;
+ }
+
++ /*
++ * Device specific workarounds (hacks). We should use DT to
++ * define partitions but we need a working TRX firmware splitter
++ * first.
++ */
++ if (of_machine_is_compatible("asus,rt-ac87u") && offset == 0x7ec0000) {
++ /*
++ * "asus" partition uses JFFS2 which we don't detect and
++ * we don't want to as this could affect other devices.
++ */
++ bcm47xxpart_add_part(&parts[curr_part++], "asus", offset, MTD_WRITEABLE);
++ continue;
++ } else if (of_machine_is_compatible("tplink,archer-c5-v2") && offset == 0xe40000) {
++ /*
++ * There is a whole set of partitions (not even listed
++ * by original firmware): "default-mac", "pin",
++ * "partition-table", etc.
++ */
++ bcm47xxpart_add_part(&parts[curr_part++], "tplink", offset, MTD_WRITEABLE);
++ continue;
++ } else if (of_machine_is_compatible("tplink,archer-c9-v1") && offset == 0xe40000) {
++ /*
++ * There is a whole set of partitions (not even listed
++ * by original firmware): "default-mac", "pin",
++ * "partition-table", etc.
++ */
++ bcm47xxpart_add_part(&parts[curr_part++], "tplink", offset, MTD_WRITEABLE);
++ continue;
++ }
++
+ /* Read beginning of the block */
+ err = mtd_read(master, offset, BCM47XXPART_BYTES_TO_READ,
+ &bytes_read, (uint8_t *)buf);
--- /dev/null
+From 6f1c62440eb6846cb8045d7a5480ec7bbe47c96f Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal@milecki.pl>
+Date: Mon, 15 Aug 2016 10:30:41 +0200
+Subject: [PATCH] BCM53573 minor hacks
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
+---
+
+--- a/arch/arm/boot/dts/bcm53573.dtsi
++++ b/arch/arm/boot/dts/bcm53573.dtsi
+@@ -48,6 +48,15 @@
+ };
+ };
+
++ timer {
++ compatible = "arm,armv7-timer";
++ interrupts = <GIC_PPI 13 0>,
++ <GIC_PPI 14 0>,
++ <GIC_PPI 11 0>,
++ <GIC_PPI 10 0>;
++ clocks = <&ilp>;
++ };
++
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+--- a/drivers/bcma/main.c
++++ b/drivers/bcma/main.c
+@@ -348,14 +348,6 @@ static int bcma_register_devices(struct
+ }
+ #endif
+
+-#ifdef CONFIG_BCMA_SFLASH
+- if (bus->drv_cc.sflash.present) {
+- err = platform_device_register(&bcma_sflash_dev);
+- if (err)
+- bcma_err(bus, "Error registering serial flash\n");
+- }
+-#endif
+-
+ #ifdef CONFIG_BCMA_NFLASH
+ if (bus->drv_cc.nflash.present) {
+ err = platform_device_register(&bcma_nflash_dev);
+@@ -436,6 +428,14 @@ int bcma_bus_register(struct bcma_bus *b
+ bcma_register_core(bus, core);
+ }
+
++#ifdef CONFIG_BCMA_SFLASH
++ if (bus->drv_cc.sflash.present) {
++ err = platform_device_register(&bcma_sflash_dev);
++ if (err)
++ bcma_err(bus, "Error registering serial flash\n");
++ }
++#endif
++
+ /* Try to get SPROM */
+ err = bcma_sprom_get(bus);
+ if (err == -ENOENT) {
+--- a/drivers/clocksource/arm_arch_timer.c
++++ b/drivers/clocksource/arm_arch_timer.c
+@@ -17,6 +17,7 @@
+ #include <linux/smp.h>
+ #include <linux/cpu.h>
+ #include <linux/cpu_pm.h>
++#include <linux/clk.h>
+ #include <linux/clockchips.h>
+ #include <linux/clocksource.h>
+ #include <linux/interrupt.h>
+@@ -836,6 +837,16 @@ static void arch_timer_of_configure_rate
+ if (of_property_read_u32(np, "clock-frequency", &arch_timer_rate))
+ arch_timer_rate = rate;
+
++ /* Get clk rate through clk driver if present */
++ if (!arch_timer_rate) {
++ struct clk *clk = of_clk_get(np, 0);
++
++ if (!IS_ERR(clk)) {
++ if (!clk_prepare_enable(clk))
++ arch_timer_rate = clk_get_rate(clk);
++ }
++ }
++
+ /* Check the timer frequency. */
+ if (arch_timer_rate == 0)
+ pr_warn("frequency not available\n");
--- /dev/null
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal@milecki.pl>
+Date: Fri, 29 Dec 2017 20:26:51 +0100
+Subject: [PATCH] Revert "ARM: dts: BCM5301X: convert to iProc QSPI"
+
+This reverts commit 1c8f4065072387d3b6ee7adcf0dbe3c7ba80c268.
+
+Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
+---
+
+--- a/arch/arm/boot/dts/bcm5301x.dtsi
++++ b/arch/arm/boot/dts/bcm5301x.dtsi
+@@ -337,6 +337,20 @@
+ };
+ };
+
++ spi@29000 {
++ reg = <0x00029000 0x1000>;
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ spi_nor: spi-nor@0 {
++ compatible = "jedec,spi-nor";
++ reg = <0>;
++ spi-max-frequency = <20000000>;
++ linux,part-probe = "ofpart", "bcm47xxpart";
++ status = "disabled";
++ };
++ };
++
+ gmac0: ethernet@24000 {
+ reg = <0x24000 0x800>;
+ };
+@@ -425,42 +439,6 @@
+ brcm,nand-has-wp;
+ };
+
+- spi@18029200 {
+- compatible = "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi";
+- reg = <0x18029200 0x184>,
+- <0x18029000 0x124>,
+- <0x1811b408 0x004>,
+- <0x180293a0 0x01c>;
+- reg-names = "mspi", "bspi", "intr_regs", "intr_status_reg";
+- interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+- <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+- <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+- <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
+- <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+- <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+- <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+- interrupt-names = "spi_lr_fullness_reached",
+- "spi_lr_session_aborted",
+- "spi_lr_impatient",
+- "spi_lr_session_done",
+- "spi_lr_overhead",
+- "mspi_done",
+- "mspi_halted";
+- clocks = <&iprocmed>;
+- clock-names = "iprocmed";
+- num-cs = <2>;
+- #address-cells = <1>;
+- #size-cells = <0>;
+-
+- spi_nor: spi-nor@0 {
+- compatible = "jedec,spi-nor";
+- reg = <0>;
+- spi-max-frequency = <20000000>;
+- linux,part-probe = "ofpart", "bcm47xxpart";
+- status = "disabled";
+- };
+- };
+-
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay-passive = <0>;
+--- a/arch/arm/boot/dts/bcm953012k.dts
++++ b/arch/arm/boot/dts/bcm953012k.dts
+@@ -80,32 +80,6 @@
+ };
+ };
+
+-&spi_nor {
+- status = "okay";
+- spi-max-frequency = <62500000>;
+- m25p,default-addr-width = <3>;
+-
+- #address-cells = <1>;
+- #size-cells = <1>;
+-
+- partition@0 {
+- label = "boot";
+- reg = <0x00000000 0x000d0000>;
+- };
+- partition@d000 {
+- label = "env";
+- reg = <0x000d0000 0x00030000>;
+- };
+- partition@100000 {
+- label = "system";
+- reg = <0x00100000 0x00600000>;
+- };
+- partition@700000 {
+- label = "rootfs";
+- reg = <0x00700000 0x00900000>;
+- };
+-};
+-
+ &uart0 {
+ status = "okay";
+ };
--- /dev/null
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal@milecki.pl>
+Date: Fri, 29 Dec 2017 22:39:45 +0100
+Subject: [PATCH] PCI: iproc: Disable DMA mapping support
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+This has been added in commit dd9d4e7498de3 ("PCI: iproc: Add inbound
+DMA mapping support") which causes a crash for bcma case. Function
+pci_dma_range_parser_init calls of_n_addr_cells with a NULL argument
+which causes a NULL pointer dereference.
+
+Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
+---
+
+--- a/drivers/pci/host/pcie-iproc.c
++++ b/drivers/pci/host/pcie-iproc.c
+@@ -1396,9 +1396,11 @@ int iproc_pcie_setup(struct iproc_pcie *
+ }
+ }
+
++if (0) {
+ ret = iproc_pcie_map_dma_ranges(pcie);
+ if (ret && ret != -ENOENT)
+ goto err_power_off_phy;
++}
+
+ #ifdef CONFIG_ARM
+ pcie->sysdata.private_data = pcie;
projects / openwrt / staging / adrian.git / commitdiff