firewire: add Kconfig help on building both stacks

Alas that won't work so good, because nobody reads help texts.

I thought about adding some crude multiple choice selection (build the
old stack, build the new stack, build both stacks).  It's possible, but
it would introduce awkward dummy config variables.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

diff --git a/drivers/firewire/Kconfig b/drivers/firewire/Kconfig
index 396dade731f9177b6354f1bfd6edcc2bff5e0642..d011a76f8e7a4d032820ffbaafd7d0c544e1a259 100644 (file)
--- a/drivers/firewire/Kconfig
+++ b/drivers/firewire/Kconfig
@@ -4,27 +4,44 @@ comment "An alternative FireWire stack is available with EXPERIMENTAL=y"
        depends on EXPERIMENTAL=n
 
 config FIREWIRE
-       tristate "IEEE 1394 (FireWire) support (JUJU alternative stack, experimental)"
+       tristate "IEEE 1394 (FireWire) support - alternative stack, EXPERIMENTAL"
        depends on EXPERIMENTAL
        select CRC_ITU_T
        help
-         IEEE 1394 describes a high performance serial bus, which is also
-         known as FireWire(tm) or i.Link(tm) and is used for connecting all
-         sorts of devices (most notably digital video cameras) to your
-         computer.
-
-         If you have FireWire hardware and want to use it, say Y here.  This
-         is the core support only, you will also need to select a driver for
-         your IEEE 1394 adapter.
-
-         To compile this driver as a module, say M here: the module will be
-         called firewire-core.
-
-         This is the "JUJU" FireWire stack, an alternative implementation
+         This is the "Juju" FireWire stack, a new alternative implementation
          designed for robustness and simplicity.  You can build either this
          stack, or the classic stack (the ieee1394 driver, ohci1394 etc.)
          or both.
 
+         To compile this driver as a module, say M here: the module will be
+         called firewire-core.  It functionally replaces ieee1394, raw1394,
+         and video1394.
+
+          NOTE:
+
+         You should only build ONE of the stacks, unless you REALLY know what
+         you are doing.  If you install both, you should configure them only as
+         modules rather than link them statically, and you should blacklist one
+         of the concurrent low-level drivers in /etc/modprobe.conf.  Add either
+
+             blacklist firewire-ohci
+         or
+             blacklist ohci1394
+
+         there depending on which driver you DON'T want to have auto-loaded.
+         You can optionally do the same with the other IEEE 1394/ FireWire
+         drivers.
+
+         If you have an old modprobe which doesn't implement the blacklist
+         directive, use either
+
+              install firewire-ohci /bin/true
+         or
+              install ohci1394 /bin/true
+
+         and so on, depending on which modules you DON't want to have
+         auto-loaded.
+
 config FIREWIRE_OHCI
        tristate "Support for OHCI FireWire host controllers"
        depends on PCI && FIREWIRE
@@ -34,11 +51,13 @@ config FIREWIRE_OHCI
          is the only chipset in use, so say Y here.
 
          To compile this driver as a module, say M here:  The module will be
-         called firewire-ohci.
+         called firewire-ohci.  It replaces ohci1394 of the classic IEEE 1394
+         stack.
+
+          NOTE:
 
-         If you also build ohci1394 of the classic IEEE 1394 driver stack,
-         blacklist either ohci1394 or firewire-ohci to let hotplug load the
-         desired driver.
+         If you also build ohci1394 of the classic stack, blacklist either
+         ohci1394 or firewire-ohci to let hotplug load only the desired driver.
 
 config FIREWIRE_SBP2
        tristate "Support for storage devices (SBP-2 protocol driver)"
@@ -50,12 +69,14 @@ config FIREWIRE_SBP2
          like scanners.
 
          To compile this driver as a module, say M here:  The module will be
-         called firewire-sbp2.
+         called firewire-sbp2.  It replaces sbp2 of the classic IEEE 1394
+         stack.
 
          You should also enable support for disks, CD-ROMs, etc. in the SCSI
          configuration section.
 
-         If you also build sbp2 of the classic IEEE 1394 driver stack,
-         blacklist either sbp2 or firewire-sbp2 to let hotplug load the
-         desired driver.
+          NOTE:
+
+         If you also build sbp2 of the classic stack, blacklist either sbp2
+         or firewire-sbp2 to let hotplug load only the desired driver.