FCC ID: A8J-ENSTAC
Engenius EnStationAC v1 is an outdoor wireless access point/bridge with
2 gigabit ethernet ports on 2 external ethernet switches,
5 GHz only wireless, internal antenna plates, and proprietery PoE.
Specification:
- QCA9557 SOC
- QCA9882 WLAN (PCI card, 5 GHz, 2x2, 26dBm)
- AR8035-A switch (RGMII GbE with PoE+ IN)
- AR8031 switch (SGMII GbE with PoE OUT)
- 40 MHz reference clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16FG
- UART at J10 (unpopulated)
- internal antenna plates (19 dbi, directional)
- 7 LEDs, 1 button (power, eth, wlan, RSSI) (reset)
MAC addresses:
MAC addresses are labeled as ETH and 5GHz
Vendor MAC addresses in flash are duplicate
eth0 ETH *:d3 art 0x0/0x6
eth1 ---- *:d4 ---
phy0 5GHz *:d5 ---
Installation:
2 ways to flash factory.bin from OEM:
- if you get Failsafe Mode from failed flash:
only use it to flash Original firmware from Engenius
or risk kernel loop or halt which requires serial cable
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
Navigate to "Firmware" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
Return to OEM:
If you have a serial cable, see Serial Failsafe instructions
otherwise, uboot-env can be used to make uboot load the failsafe image
*DISCLAIMER*
The Failsafe image is unique to Engenius boards.
If the failsafe image is missing or damaged this will not work
DO NOT downgrade to ar71xx this way, it can cause kernel loop or halt
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
TFTP recovery:
rename initramfs to 'vmlinux-art-ramdisk'
make available on TFTP server at 192.168.1.101
power board
hold or press reset button repeatedly
NOTE: for some Engenius boards TFTP is not reliable
try setting MTU to 600 and try many times
Format of OEM firmware image:
The OEM software of EnStationAC is a heavily modified version
of Openwrt Altitude Adjustment 12.09. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
openwrt-ar71xx-enstationac-uImage-lzma.bin
openwrt-ar71xx-enstationac-root.squashfs
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring.
Newer EnGenius software requires more checks but their script
includes a way to skip them, otherwise the tar must include
a text file with the version and md5sums in a deprecated format.
The OEM upgrade script is at /etc/fwupgrade.sh.
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8033 switch between
the SOC and the ethernet PHY chips.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
For eth0 at 1000 speed, the value returned was
ae000000 but that didn't work, so following
the logical pattern from the rest of the values,
the guessed value of
a3000000 works better.
later discovered that delay can be placed on the PHY end only
with phy-mode as 'rgmii-id' and set register to 0x82...
Tested from master, all link speeds functional
Signed-off-by: Michael Pratt <mcpratt@pm.me>
[fixed SoB to match From:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
engenius,ecb350-v1|\
engenius,enh202-v1|\
engenius,ens202ext-v1|\
+engenius,enstationac-v1|\
etactica,eg200|\
glinet,gl-ar750s-nor|\
glinet,gl-ar750s-nor-nand|\
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca955x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "engenius,enstationac-v1", "qca,qca9557";
+ model = "EnGenius EnStationAC v1";
+
+ aliases {
+ label-mac-device = ð0;
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "amber:power";
+ gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ wlan {
+ label = "green:wlan";
+ gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ rssilow {
+ label = "red:rssilow";
+ gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+ };
+
+ rssimedium {
+ label = "amber:rssimedium";
+ gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
+ };
+
+ rssihigh {
+ label = "green:rssihigh";
+ gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ virtual_flash {
+ compatible = "mtd-concat";
+
+ devices = <&firmware1 &firmware2>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ compatible = "openwrt,okli";
+ label = "firmware";
+ reg = <0x0 0x0>;
+ };
+ };
+ };
+};
+
+&uart {
+ status = "okay";
+};
+
+&spi {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "u-boot-env";
+ reg = <0x040000 0x010000>;
+ };
+
+ partition@50000 {
+ label = "custom";
+ reg = <0x050000 0x050000>;
+ read-only;
+ };
+
+ partition@a0000 {
+ label = "loader";
+ reg = <0x0a0000 0x010000>;
+ read-only;
+ };
+
+ firmware2: partition@b0000 {
+ label = "firmware2";
+ reg = <0x0b0000 0x170000>;
+ };
+
+ partition@220000 {
+ label = "fakeroot";
+ reg = <0x220000 0x010000>;
+ read-only;
+ };
+
+ firmware1: partition@230000 {
+ label = "firmware1";
+ reg = <0x230000 0xb40000>;
+ };
+
+ partition@d70000 {
+ label = "failsafe";
+ reg = <0xd70000 0x280000>;
+ read-only;
+ };
+
+ art: partition@ff0000 {
+ label = "art";
+ reg = <0xff0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ eee-broken-100tx;
+ eee-broken-1000t;
+ };
+
+ phy2: ethernet-phy@2 {
+ reg = <2>;
+ eee-broken-100tx;
+ eee-broken-1000t;
+ at803x-override-sgmii-link-check;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ mtd-mac-address = <&art 0x0>;
+
+ phy-handle = <&phy1>;
+ phy-mode = "rgmii-id";
+
+ pll-data = <0x82000000 0x80000101 0x80001313>;
+};
+
+ð1 {
+ status = "okay";
+
+ mtd-mac-address = <&art 0x0>;
+ mtd-mac-address-increment = <1>;
+
+ phy-handle = <&phy2>;
+
+ pll-data = <0x03000000 0x00000101 0x00001313>;
+
+ qca955x-sgmii-fixup;
+};
+
+&pcie0 {
+ status = "okay";
+
+ wifi@0,0,0 {
+ compatible = "qcom,ath10k";
+ reg = <0x0 0 0 0 0>;
+ qca,no-eeprom;
+ };
+};
ucidef_set_led_rssi "rssimedium" "RSSIMEDIUM" "amber:rssimedium" "wlan0" "33" "100"
ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "green:rssihigh" "wlan0" "67" "100"
;;
-engenius,ens202ext-v1)
+engenius,ens202ext-v1|\
+engenius,enstationac-v1)
ucidef_set_rssimon "wlan0" "200000" "1"
ucidef_set_led_rssi "rssilow" "RSSILOW" "red:rssilow" "wlan0" "1" "100"
ucidef_set_led_rssi "rssimedium" "RSSIMEDIUM" "amber:rssimedium" "wlan0" "33" "100"
"ath10k/cal-pci-0000:00:00.0.bin")
case $board in
allnet,all-wap02860ac|\
+ engenius,enstationac-v1|\
glinet,gl-x750)
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) +2)
endef
TARGET_DEVICES += engenius_ens202ext-v1
+define Device/engenius_enstationac-v1
+ $(Device/engenius_loader_okli)
+ SOC := qca9557
+ DEVICE_MODEL := EnStationAC
+ DEVICE_VARIANT := v1
+ DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct rssileds
+ IMAGE_SIZE := 11520k
+ LOADER_FLASH_OFFS := 0x230000
+ ENGENIUS_IMGNAME := ar71xx-generic-enstationac
+endef
+TARGET_DEVICES += engenius_enstationac-v1
+
define Device/engenius_epg5000
SOC := qca9558
DEVICE_VENDOR := EnGenius
projects / openwrt / staging / adrian.git / commitdiff