Fix in commit
25eead21c5ab ("ath79: fix 5GHz on QCA9886 variant of ZTE MF286")
was incomplete. A user of such variant popped up, and in the boot log
after installation, we discovered that QCA9886 expects different
pre-calibration data size, than the older QCA9880 variant:
ath10k_pci 0000:00:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
ath10k_pci 0000:00:00.0: firmware ver 10.4b-ct-9888-fW-13-
5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32
59e741e7
ath10k_pci 0000:00:00.0: invalid calibration data length in nvmem-cell 'pre-calibration': 2116 != 12064
ath10k_pci 0000:00:00.0: Loading BDF type 0
ath10k_pci 0000:00:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0056,subsystem-vendor=0000,subsystem-device=0000 from ath10k/QCA9888/hw2.0/board-2.bin
ath10k_pci 0000:00:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9888/hw2.0
ath10k_pci 0000:00:00.0: failed to fetch board file: -12
ath10k_pci 0000:00:00.0: could not probe fw (-12)
Explicitly define a pre-calibration nvmem-cell for this variant, and use
it instead of the calibration one, which is shorter.
Fixes: 25eead21c5ab ("ath79: fix 5GHz on QCA9886 variant of ZTE MF286")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16809
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
#address-cells = <1>;
#size-cells = <1>;
+ /* ath9k */
cal_caldata_1000: cal@1000 {
reg = <0x1000 0x440>;
};
+ /* ath10k wave1 in plain MF286 */
cal_caldata_5000: cal@5000 {
reg = <0x5000 0x844>;
};
+
+ /* ath10k wave2 in early MF286A */
+ precal_caldata_5000: precal@5000 {
+ reg = <0x5000 0x2f20>;
+ };
};
};
};
&wifi_ath10k {
- nvmem-cells = <&macaddr_mac_0 1>, <&cal_caldata_5000>, <&cal_caldata_5000>;
+ nvmem-cells = <&macaddr_mac_0 1>, <&cal_caldata_5000>, <&precal_caldata_5000>;
nvmem-cell-names = "mac-address", "calibration", "pre-calibration";
};