ipq40xx: add support for MobiPromo CM520-79F

MobiPromo CM520-79F is an AC1300 dual band router based on IPQ4019

Specification:

SoC/Wireless: QCA IPQ4019
RAM: 512MiB
Flash: 128MiB SLC NAND
Ethernet PHY: QCA8075
Ethernet ports: 1x WAN, 2x LAN
LEDs: 7 LEDs
      2 (USB, CAN) are GPIO
      other 5 (2.4G, 5G, LAN1, LAN2, WAN) are connected to a shift register
Button: Reset

Flash instruction:
Disassemble the router, connect UART pins like this:
 GND TX    RX
  [x x . . x .]
  [. . . . . .]

(QCA8075 and IPQ4019 below)
Baud-rate: 115200

Set up TFTP server: IP 192.168.1.188/24
Power on the router and interrupt the booting with UART console
env backup (in case you want to go back to stock and need it there):
	printenv
	(Copy the output to somewhere save)
Set bootenv:
	setenv set_ubi 'set mtdids nand0=nand0; set mtdparts mtdparts=nand0:0x7480000@0xb80000(fs); ubi part fs'
	setenv bootkernel 'ubi read 0x84000000 kernel; bootm 0x84000000#config@1'
	setenv cm520_boot 'run set_ubi; run bootkernel'
	setenv bootcmd 'run cm520_boot'
	setenv bootargs
	saveenv
Boot initramfs from TFTP:
	tftpboot openwrt-ipq40xx-generic-mobipromo_cm520-79f-initramfs-fit-zImage.itb
	bootm
After initramfs image is booted, backup rootfs partition in case of reverting to stock image
	cat /dev/mtd12 > /tmp/mtd12.bin
Then fetch it via SCP

Upload nand-factory.ubi to /tmp via SCP, then run
	mtd erase rootfs
	mtd write /tmp/*nand-factory.ubi rootfs
	reboot

To revert to stock image, restore default bootenv in uboot UART console
	setenv bootcmd 'bootipq'
	printenv
use the saved dump you did back when you installed OpenWrt to verify that
there are no other differences from back in the day.
	saveenv
upload the backed up mtd12.bin and run
	tftpboot mtd12.bin
	nand erase 0xb80000 0x7480000
	nand write 0x84000000 0xb80000 0x7480000
The BOOTCONFIG may have been configured to boot from alternate partition (rootfs_1) instead
In case of this, set it back to rootfs:
	cd /tmp
	cat /dev/mtd7 > mtd7.bin
	echo -ne '\x0b' | dd of=mtd7.bin conv=notrunc bs=1 count=1 seek=4
	for i in 28 48 68 108; do
		dd if=/dev/zero of=mtd7.bin conv=notrunc bs=1 count=1 seek=$i
	done
	mtd write mtd7.bin BOOTCONFIG
	mtd write mtd7.bin BOOTCONFIG1

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[renamed volume to ubi to support autoboot,
as per David Lam's test in PR#2432]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

diff --git a/board-mobipromo_cm520-79f.qca4019 b/board-mobipromo_cm520-79f.qca4019
new file mode 100644 (file)
index 0000000..d717af1
Binary files /dev/null and b/board-mobipromo_cm520-79f.qca4019 differ