--- /dev/null
+--- a/arch/arm/mach-kirkwood/Kconfig
++++ b/arch/arm/mach-kirkwood/Kconfig
+@@ -25,6 +25,9 @@ config TARGET_LSXL
+ config TARGET_POGO_E02
+ bool "pogo_e02 Board"
+
++config TARGET_POGOPLUGV4
++ bool "Pogoplug V4 Board"
++
+ config TARGET_DNS325
+ bool "dns325 Board"
+
+@@ -77,6 +80,7 @@ source "board/Marvell/guruplug/Kconfig"
+ source "board/Marvell/sheevaplug/Kconfig"
+ source "board/buffalo/lsxl/Kconfig"
+ source "board/cloudengines/pogo_e02/Kconfig"
++source "board/cloudengines/pogoplugv4/Kconfig"
+ source "board/d-link/dns325/Kconfig"
+ source "board/iomega/iconnect/Kconfig"
+ source "board/keymile/km_arm/Kconfig"
+--- a/arch/arm/mach-kirkwood/include/mach/config.h
++++ b/arch/arm/mach-kirkwood/include/mach/config.h
+@@ -77,6 +77,7 @@
+ * Ethernet Driver configuration
+ */
+ #ifdef CONFIG_CMD_NET
++#define CONFIG_FEATURE_COMMAND_EDITING
+ #define CONFIG_NETCONSOLE /* include NetConsole support */
+ #define CONFIG_MII /* expose smi ove miiphy interface */
+ #define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */
+@@ -110,6 +111,7 @@
+ #define CONFIG_SYS_ATA_STRIDE 4
+ /* Controller supports 48-bits LBA addressing */
+ #define CONFIG_LBA48
++#define CONFIG_SYS_64BIT_LBA
+ /* CONFIG_IDE requires some #defines for ATA registers */
+ #define CONFIG_SYS_IDE_MAXBUS 2
+ #define CONFIG_SYS_IDE_MAXDEVICE 2
+@@ -134,4 +136,15 @@
+ #define CONFIG_SYS_TIMER_COUNTER (MVEBU_TIMER_BASE + 0x14)
+ #define CONFIG_SYS_TIMER_RATE CONFIG_SYS_TCLK
+
++/*
++ * Boot option
++ */
++#define CONFIG_CMD_BOOTZ
++
++/*
++ * GPIO
++ */
++#define CONFIG_CMD_GPIO
++#define CONFIG_KIRKWOOD_GPIO
++
+ #endif /* _KW_CONFIG_H */
+--- a/arch/arm/mach-kirkwood/include/mach/kw88f6192.h
++++ b/arch/arm/mach-kirkwood/include/mach/kw88f6192.h
+@@ -16,6 +16,6 @@
+ #define KW_REGS_PHY_BASE KW88F6192_REGS_PHYS_BASE
+
+ /* TCLK Core Clock defination */
+-#define CONFIG_SYS_TCLK 166000000 /* 166MHz */
++#define CONFIG_SYS_TCLK 166666667 /* 166MHz */
+
+ #endif /* _CONFIG_KW88F6192_H */
+--- a/arch/arm/mach-kirkwood/include/mach/mpp.h
++++ b/arch/arm/mach-kirkwood/include/mach/mpp.h
+@@ -217,10 +217,12 @@
+ #define MPP33_GPIO MPP( 33, 0x0, 1, 1, 0, 1, 1, 1 )
+ #define MPP33_TDM_DTX MPP( 33, 0x2, 0, 1, 0, 0, 1, 1 )
+ #define MPP33_GE1_13 MPP( 33, 0x3, 0, 0, 0, 1, 1, 1 )
++#define MPP33_SATA1_ACTn MPP( 33, 0x5, 0, 1, 0, 1, 1, 1 )
+
+ #define MPP34_GPIO MPP( 34, 0x0, 1, 1, 0, 1, 1, 1 )
+ #define MPP34_TDM_SPI_CS1 MPP( 34, 0x2, 0, 1, 0, 0, 1, 1 )
+ #define MPP34_GE1_14 MPP( 34, 0x3, 0, 0, 0, 1, 1, 1 )
++#define MPP34_SATA1_ACTn MPP( 34, 0x5, 0, 1, 0, 1, 1, 1 )
+
+ #define MPP35_GPIO MPP( 35, 0x0, 1, 1, 1, 1, 1, 1 )
+ #define MPP35_TDM_CH0_TX_QL MPP( 35, 0x2, 0, 1, 0, 0, 1, 1 )
+--- a/arch/arm/mach-mvebu/include/mach/soc.h
++++ b/arch/arm/mach-mvebu/include/mach/soc.h
+@@ -18,6 +18,8 @@
+ #define SOC_88F6810_ID 0x6810
+ #define SOC_88F6820_ID 0x6820
+ #define SOC_88F6828_ID 0x6828
++#define SOC_88F6192_ID 0x6192
++#define SOC_88F6702_ID 0x6702
+
+ /* A375 revisions */
+ #define MV_88F67XX_A0_ID 0x3
+--- /dev/null
++++ b/board/cloudengines/pogoplugv4/Kconfig
+@@ -0,0 +1,12 @@
++if TARGET_POGOPLUGV4
++
++config SYS_BOARD
++ default "pogoplugv4"
++
++config SYS_VENDOR
++ default "cloudengines"
++
++config SYS_CONFIG_NAME
++ default "pogoplugv4"
++
++endif
+--- /dev/null
++++ b/board/cloudengines/pogoplugv4/MAINTAINERS
+@@ -0,0 +1,6 @@
++POGOPLUGV4 BOARD
++M: Alberto Bursi <alberto.bursi@outlook.it>
++S: Maintained
++F: board/cloudengines/pogoplugv4/
++F: include/configs/pogoplugv4.h
++F: configs/pogoplugv4_defconfig
+--- /dev/null
++++ b/board/cloudengines/pogoplugv4/Makefile
+@@ -0,0 +1,11 @@
++#
++# (C) Copyright 2009 bodhi <mibodhi@gmail.com>
++#
++# Based on
++# Marvell Semiconductor <www.marvell.com>
++# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
++#
++# SPDX-License-Identifier: GPL-2.0+
++#
++
++obj-y := pogoplugv4.o
+--- /dev/null
++++ b/board/cloudengines/pogoplugv4/kwbimage.cfg
+@@ -0,0 +1,167 @@
++#
++# Copyright (C) 2012
++# David Purdy <david.c.purdy@gmail.com>
++#
++# Based on Kirkwood support:
++# (C) Copyright 2009
++# Marvell Semiconductor <www.marvell.com>
++# Written-by: Prafulla Wadaskar <prafulla <at> marvell.com>
++#
++# See file CREDITS for list of people who contributed to this
++# project.
++#
++# This program is free software; you can redistribute it and/or
++# modify it under the terms of the GNU General Public License as
++# published by the Free Software Foundation; either version 2 of
++# the License, or (at your option) any later version.
++#
++# This program is distributed in the hope that it will be useful,
++# but WITHOUT ANY WARRANTY; without even the implied warranty of
++# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++# GNU General Public License for more details.
++#
++# You should have received a copy of the GNU General Public License
++# along with this program; If not, see <http://www.gnu.org/licenses/>.
++#
++# Refer docs/README.kwimage for more details about how-to configure
++# and create kirkwood boot image
++#
++
++# Boot Media configurations (DONE)
++BOOT_FROM nand
++NAND_ECC_MODE default
++NAND_PAGE_SIZE 0x0800
++
++# SOC registers configuration using bootrom header extension
++# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
++
++# Configure RGMII-0 interface pad voltage to 1.8V (SHOULD BE SAME)
++DATA 0xffd100e0 0x1b1b1b9b
++
++#Dram initalization for SINGLE x16 CL=3 @ 200MHz (need CL=3 @ 200MHz?)
++DATA 0xffd01400 0x43000618 # DDR Configuration register
++# bit13-0: 0x200 (200 DDR2 clks refresh rate)
++# bit23-14: zero
++# bit24: 1= enable exit self refresh mode on DDR access
++# bit25: 1 required
++# bit29-26: zero
++# bit31-30: 01
++
++DATA 0xffd01404 0x34143000 # DDR Controller Control Low
++# bit 4: 0=addr/cmd in smame cycle
++# bit 5: 0=clk is driven during self refresh, we don't care for APX
++# bit 6: 0=use recommended falling edge of clk for addr/cmd
++# bit14: 0=input buffer always powered up
++# bit18: 1=cpu lock transaction enabled
++# bit23-20: 3=recommended value for CL=3 and STARTBURST_DEL disabled bit31=0
++# bit27-24: 6= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
++# bit30-28: 3 required
++# bit31: 0=no additional STARTBURST delay
++
++DATA 0xffd01408 0x11012227 # DDR Timing (Low) (active cycles value +1)
++# bit3-0: TRAS lsbs
++# bit7-4: TRCD
++# bit11- 8: TRP
++# bit15-12: TWR
++# bit19-16: TWTR
++# bit20: TRAS msb
++# bit23-21: 0x0
++# bit27-24: TRRD
++# bit31-28: TRTP
++
++DATA 0xffd0140c 0x00000819 # DDR Timing (High)
++# bit6-0: TRFC
++# bit8-7: TR2R
++# bit10-9: TR2W
++# bit12-11: TW2W
++# bit31-13: zero required
++
++DATA 0xffd01410 0x00000001 # DDR Address Control (changed to Dockstar vals)
++# bit1-0: 00, Cs0width=x16
++# bit3-2: 10, Cs0size=512Mb
++# bit5-4: 00, Cs2width=nonexistent
++# bit7-6: 00, Cs1size =nonexistent
++# bit9-8: 00, Cs2width=nonexistent
++# bit11-10: 00, Cs2size =nonexistent
++# bit13-12: 00, Cs3width=nonexistent
++# bit15-14: 00, Cs3size =nonexistent
++# bit16: 0, Cs0AddrSel
++# bit17: 0, Cs1AddrSel
++# bit18: 0, Cs2AddrSel
++# bit19: 0, Cs3AddrSel
++# bit31-20: 0 required
++
++DATA 0xffd01414 0x00000000 # DDR Open Pages Control
++# bit0: 0, OpenPage enabled
++# bit31-1: 0 required
++
++DATA 0xffd01418 0x00000000 # DDR Operation
++# bit3-0: 0x0, DDR cmd
++# bit31-4: 0 required
++
++DATA 0xffd0141c 0x00000632 # DDR Mode
++# bit2-0: 2, BurstLen=2 required
++# bit3: 0, BurstType=0 required
++# bit6-4: 4, CL=5 (<===== change to CL=3 ?)
++# bit7: 0, TestMode=0 normal
++# bit8: 0, DLL reset=0 normal
++# bit11-9: 6, auto-precharge write recovery ????????????
++# bit12: 0, PD must be zero
++# bit31-13: 0 required
++
++DATA 0xffd01420 0x00000040 # DDR Extended Mode
++# bit0: 0, DDR DLL enabled
++# bit1: 0, DDR drive strenght normal
++# bit2: 0, DDR ODT control lsd (disabled)
++# bit5-3: 000, required
++# bit6: 1, DDR ODT control msb, (disabled)
++# bit9-7: 000, required
++# bit10: 0, differential DQS enabled
++# bit11: 0, required
++# bit12: 0, DDR output buffer enabled
++# bit31-13: 0 required
++
++DATA 0xffd01424 0x0000F07F # DDR Controller Control High
++# bit2-0: 111, required
++# bit3 : 1 , MBUS Burst Chop disabled
++# bit6-4: 111, required
++# bit7 : 0
++# bit8 : 0 , no sample stage
++# bit9 : 0 , no half clock cycle addition to dataout
++# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
++# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
++# bit15-12: 1111 required
++# bit31-16: 0 required
++
++DATA 0xffd01428 0x00085520 # DDR2 ODT Read Timing (default values)
++DATA 0xffd0147c 0x00008552 # DDR2 ODT Write Timing (default values)
++
++DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
++DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size
++# bit0: 1, Window enabled
++# bit1: 0, Write Protect disabled
++# bit3-2: 00, CS0 hit selected
++# bit23-4: ones, required
++# bit31-24: 0x07, Size (i.e. 128MB)
++
++DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
++DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
++DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
++
++DATA 0xffd01494 0x00030000 # DDR ODT Control (Low) (DONE)
++# bit3-0: 2, ODT0Rd, MODT[0] asserted during read from DRAM CS1
++# bit7-4: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
++# bit19-16:2, ODT0Wr, MODT[0] asserted during write to DRAM CS1
++# bit23-20:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
++
++DATA 0xffd01498 0x00000000 # DDR ODT Control (High) (DONE)
++# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
++# bit3-2: 01, ODT1 active NEVER!
++# bit31-4: zero, required
++
++DATA 0xffd0149c 0x0000e803 # CPU ODT Control (DONE)
++DATA 0xffd01480 0x00000001 # DDR Initialization Control (DONE)
++#bit0=1, enable DDR init upon this register write
++
++# End of Header extension
++DATA 0x0 0x0
+--- /dev/null
++++ b/board/cloudengines/pogoplugv4/pogoplugv4.c
+@@ -0,0 +1,223 @@
++/*
++ * Copyright (C) 2016 bodhi <mibodhi@gmail.com>
++ * Copyright (C) 2014 bodhi <mibodhi@gmail.com>
++ *
++ * Based on
++ *
++ * Copyright (C) 2014 <ebbes.ebbes@gmail.com>
++ *
++ * Copyright (C) 2012
++ * David Purdy <david.c.purdy@gmail.com>
++ *
++ * Based on Kirkwood support:
++ * (C) Copyright 2009
++ * Marvell Semiconductor <www.marvell.com>
++ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
++ *
++ * See file CREDITS for list of people who contributed to this
++ * project.
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License as
++ * published by the Free Software Foundation; either version 2 of
++ * the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; If not, see <http://www.gnu.org/licenses/>.
++ */
++
++#include <common.h>
++#include <miiphy.h>
++#include <asm/arch/cpu.h>
++#include <asm/arch/soc.h>
++#include <asm/arch/mpp.h>
++#include <asm/io.h>
++#include "pogoplugv4.h"
++#include <asm/arch/gpio.h>
++
++#ifdef CONFIG_KIRKWOOD_MMC
++#include <kirkwood_mmc.h>
++#endif /* CONFIG_KIRKWOOD_MMC */
++
++
++DECLARE_GLOBAL_DATA_PTR;
++
++int board_early_init_f(void)
++{
++ /*
++ * default gpio configuration
++ * There are maximum 64 gpios controlled through 2 sets of registers
++ * the below configuration configures mainly initial LED status
++ */
++ mvebu_config_gpio(POGOPLUGV4_OE_VAL_LOW,
++ POGOPLUGV4_OE_VAL_HIGH,
++ POGOPLUGV4_OE_LOW, POGOPLUGV4_OE_HIGH);
++
++ /* Multi-Purpose Pins Functionality configuration */
++ u32 kwmpp_config[] = {
++ MPP0_NF_IO2,
++ MPP1_NF_IO3,
++ MPP2_NF_IO4,
++ MPP3_NF_IO5,
++ MPP4_NF_IO6,
++ MPP5_NF_IO7,
++ MPP6_SYSRST_OUTn,
++ MPP7_GPO,
++ MPP8_TW_SDA,
++ MPP9_TW_SCK,
++ MPP10_UART0_TXD,
++ MPP11_UART0_RXD,
++ MPP12_SD_CLK,
++ MPP13_SD_CMD,
++ MPP14_SD_D0,
++ MPP15_SD_D1,
++ MPP16_SD_D2,
++ MPP17_SD_D3,
++ MPP18_NF_IO0,
++ MPP19_NF_IO1,
++ MPP20_SATA1_ACTn,
++ MPP21_SATA0_ACTn,
++ MPP22_GPIO, /* Green LED */
++ MPP23_GPIO,
++ MPP24_GPIO, /* Red LED */
++ MPP25_GPIO,
++ MPP26_GPIO,
++ MPP27_GPIO,
++ MPP28_GPIO,
++ MPP29_GPIO, /* Eject button */
++ MPP30_GPIO,
++ MPP31_GPIO,
++ MPP32_GPIO,
++ MPP33_GPIO,
++ MPP34_GPIO,
++ MPP35_GPIO, /* FR6192 has only 36 GPIOs */
++ 0
++ };
++ kirkwood_mpp_conf(kwmpp_config, NULL);
++
++ return 0;
++}
++
++int board_init(void)
++{
++ /* Boot parameters address */
++ gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
++
++ kw_gpio_set_valid(20, 1);
++ kw_gpio_set_valid(21, 1);
++ kw_gpio_set_valid(22, 1);
++ kw_gpio_set_valid(24, 1);
++
++ return 0;
++}
++
++#ifdef CONFIG_RESET_PHY_R
++/* Configure and initialize PHY */
++void reset_phy(void)
++{
++ u16 reg;
++ u16 devadr;
++ char *name = "egiga0";
++
++ if (miiphy_set_current_dev(name))
++ return;
++
++ /* command to read PHY dev address */
++ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
++ printf("Err..(%s) could not read PHY dev address\n", __func__);
++ return;
++ }
++
++ /*
++ * Enable RGMII delay on Tx and Rx for CPU port
++ * Ref: sec 4.7.2 of chip datasheet
++ */
++ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
++ miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
++ reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
++ miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
++ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
++
++ /* reset the phy */
++ miiphy_reset(name, devadr);
++
++ debug("88E1116 Initialized on %s\n", name);
++}
++#endif /* CONFIG_RESET_PHY_R */
++
++#ifdef CONFIG_KIRKWOOD_MMC
++int board_mmc_init(bd_t *bis)
++{
++ kw_mmc_initialize(bis);
++ return 0;
++}
++#endif /* CONFIG_KIRKWOOD_MMC */
++
++
++#define GREEN_LED (1 << 22)
++#define RED_LED (1 << 24)
++#define BOTH_LEDS (GREEN_LED | RED_LED)
++#define NEITHER_LED 0
++
++static void set_leds(u32 leds, u32 blinking)
++{
++ struct kwgpio_registers *r;
++ u32 oe;
++ u32 bl;
++
++ r = (struct kwgpio_registers *)MVEBU_GPIO0_BASE;
++ oe = readl(&r->oe) | BOTH_LEDS;
++ writel(oe & ~leds, &r->oe); /* active low */
++ bl = readl(&r->blink_en) & ~BOTH_LEDS;
++ writel(bl | blinking, &r->blink_en);
++}
++
++void show_boot_progress(int val)
++{
++ switch (val) {
++ case BOOTSTAGE_ID_RUN_OS: /* booting Linux */
++ set_leds(BOTH_LEDS, NEITHER_LED);
++ break;
++ case BOOTSTAGE_ID_NET_ETH_START: /* Ethernet initialization */
++ set_leds(GREEN_LED, GREEN_LED);
++ break;
++ default:
++ if (val < 0) /* error */
++ set_leds(RED_LED, RED_LED);
++ break;
++ }
++}
++
++#if defined(CONFIG_KIRKWOOD_GPIO)
++/* Return GPIO button status */
++/*
++un-pressed:
++ gpio-29 (Eject Button ) in hi (act lo) - IRQ edge (clear )
++pressed
++ gpio-29 (Eject Button ) in lo (act hi) - IRQ edge (clear )
++*/
++
++static int
++do_read_button(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
++{
++ if (strcmp(argv[1], "eject") == 0) {
++ kw_gpio_set_valid(BTN_EJECT, GPIO_INPUT_OK);
++ kw_gpio_direction_input(BTN_EJECT);
++ return kw_gpio_get_value(BTN_EJECT);
++ }
++ else
++ return -1;
++}
++
++
++U_BOOT_CMD(button, 2, 0, do_read_button,
++ "Return GPIO button status 0=off 1=on",
++ "- button eject: test buttons states\n"
++);
++
++#endif
+--- /dev/null
++++ b/board/cloudengines/pogoplugv4/pogoplugv4.h
+@@ -0,0 +1,50 @@
++/*
++ * Copyright (C) 2016
++ * bodhi <mibodhi@gmail.com>
++ *
++ * Copyright (C) 2012
++ * David Purdy <david.c.purdy@gmail.com>
++ *
++ * Based on Kirkwood support:
++ * (C) Copyright 2009
++ * Marvell Semiconductor <www.marvell.com>
++ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
++ *
++ * See file CREDITS for list of people who contributed to this
++ * project.
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License as
++ * published by the Free Software Foundation; either version 2 of
++ * the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; If not, see <http://www.gnu.org/licenses/>.
++ */
++
++#ifndef __POGOPLUGV4_H
++#define __POGOPLUGV4_H
++
++/* GPIO configuration */
++#define POGOPLUGV4_OE_LOW (~(0))
++#define POGOPLUGV4_OE_HIGH (~(0))
++#define POGOPLUGV4_OE_VAL_LOW (1 << 29)
++#define POGOPLUGV4_OE_VAL_HIGH 0
++
++/* PHY related */
++#define MV88E1116_LED_FCTRL_REG 10
++#define MV88E1116_CPRSP_CR3_REG 21
++#define MV88E1116_MAC_CTRL_REG 21
++#define MV88E1116_PGADR_REG 22
++#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
++#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
++
++/* button */
++#define BTN_EJECT 29
++
++#endif /* __POGOPLUGV4_H */
+--- /dev/null
++++ b/configs/pogoplugv4_defconfig
+@@ -0,0 +1,35 @@
++CONFIG_ARM=y
++CONFIG_KIRKWOOD=y
++CONFIG_TARGET_POGOPLUGV4=y
++CONFIG_SYS_PROMPT="pogoplugv4> "
++CONFIG_IDENT_STRING="\nPogoplug V4"
++CONFIG_BOOTDELAY=3
++# CONFIG_CMD_IMLS is not set
++# CONFIG_CMD_FLASH is not set
++CONFIG_SYS_NS16550=y
++CONFIG_CMD_FDT=y
++CONFIG_OF_LIBFDT=y
++CONFIG_CMD_SETEXPR=y
++CONFIG_CMD_DHCP=y
++CONFIG_CMD_MII=y
++CONFIG_CMD_PING=y
++CONFIG_CMD_DNS=y
++CONFIG_CMD_SNTP=y
++CONFIG_CMD_USB=y
++CONFIG_CMD_DATE=y
++CONFIG_CMD_EXT2=y
++CONFIG_CMD_EXT4=y
++CONFIG_CMD_FAT=y
++CONFIG_CMD_JFFS2=y
++CONFIG_CMD_MTDPARTS=y
++CONFIG_CMD_ENV=y
++CONFIG_CMD_NAND=y
++CONFIG_CMD_MMC=y
++CONFIG_EFI_PARTITION=y
++CONFIG_ENV_IS_IN_NAND=y
++CONFIG_CMD_UBI=y
++CONFIG_USB=y
++CONFIG_USB_EHCI_HCD=y
++CONFIG_USB_STORAGE=y
++CONFIG_LZMA=y
++CONFIG_LZO=y
+--- a/drivers/gpio/kw_gpio.c
++++ b/drivers/gpio/kw_gpio.c
+@@ -148,3 +148,36 @@ void kw_gpio_set_blink(unsigned pin, int
+ /* Set blinking. */
+ __set_blinking(pin, blink);
+ }
++
++
++/*
++ * Hooks to GENERIC_GPIO primitives
++ */
++
++int gpio_direction_input(unsigned pin)
++{
++ return kw_gpio_direction_input(pin);
++}
++
++int gpio_direction_output(unsigned pin, int value)
++{
++ return kw_gpio_direction_output(pin, value);
++}
++
++void gpio_set_value(unsigned pin, int value) {
++ kw_gpio_set_value(pin, value);
++}
++
++int gpio_get_value(unsigned pin) {
++ return kw_gpio_get_value(pin);
++}
++
++int gpio_request(unsigned gpio, const char *label)
++{
++ return 0;
++}
++
++int gpio_free(unsigned gpio)
++{
++ return 0;
++}
+--- a/drivers/mmc/Makefile
++++ b/drivers/mmc/Makefile
+@@ -61,6 +61,7 @@ obj-$(CONFIG_MMC_SDHCI_TANGIER) += tang
+ obj-$(CONFIG_MMC_SDHCI_TEGRA) += tegra_mmc.o
+ obj-$(CONFIG_MMC_SDHCI_XENON) += xenon_sdhci.o
+ obj-$(CONFIG_MMC_SDHCI_ZYNQ) += zynq_sdhci.o
++obj-$(CONFIG_KIRKWOOD_MMC) += kirkwood_mmc.o
+
+ obj-$(CONFIG_MMC_SUNXI) += sunxi_mmc.o
+ obj-$(CONFIG_MMC_UNIPHIER) += uniphier-sd.o
+--- /dev/null
++++ b/drivers/mmc/kirkwood_mmc.c
+@@ -0,0 +1,482 @@
++/*
++ * (C) Copyright 2014 bodhi <mibodhi@gmail.com>
++ *
++ * Based on
++ *
++ * (C) Copyright 2014 <ebbes.ebbes@gmail.com>
++ *
++ * Based on
++ *
++ * Driver for Marvell SDIO/MMC controller
++ *
++ * (C) Copyright 2012
++ * Marvell Semiconductor <www.marvell.com>
++ * Written-by: Gérald Kerma <uboot at doukki.net>
++ * See file CREDITS for list of people who contributed to this
++ * project.
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License as
++ * published by the Free Software Foundation; either version 2 of
++ * the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
++ * MA 02111-1307 USA
++ */
++
++#include <common.h>
++#include <malloc.h>
++#include <part.h>
++#include <mmc.h>
++#include <asm/io.h>
++#include <asm/arch/cpu.h>
++#include <asm/arch/soc.h>
++
++#include <kirkwood_mmc.h>
++
++#define DRIVER_NAME "kwsdio"
++
++static int kw_mmc_setup_data(struct mmc_data *data)
++{
++ u32 ctrl_reg;
++
++#ifdef DEBUG
++ printf("%s, data %s : blocks=%d blksz=%d\n", DRIVER_NAME,
++ (data->flags & MMC_DATA_READ) ? "read" : "write",
++ data->blocks, data->blocksize);
++#endif
++
++ /* default to maximum timeout */
++ ctrl_reg = kwsd_read(SDIO_HOST_CTRL);
++ ctrl_reg |= SDIO_HOST_CTRL_TMOUT(SDIO_HOST_CTRL_TMOUT_MAX);
++ kwsd_write(SDIO_HOST_CTRL, ctrl_reg);
++
++ if (data->flags & MMC_DATA_READ) {
++ kwsd_write(SDIO_SYS_ADDR_LOW,(u32)data->dest & 0xffff);
++ kwsd_write(SDIO_SYS_ADDR_HI,(u32)data->dest >> 16);
++ } else {
++ kwsd_write(SDIO_SYS_ADDR_LOW,(u32)data->src & 0xffff);
++ kwsd_write(SDIO_SYS_ADDR_HI,(u32)data->src >> 16);
++ }
++
++ kwsd_write(SDIO_BLK_COUNT, data->blocks);
++ kwsd_write(SDIO_BLK_SIZE, data->blocksize);
++
++ return 0;
++}
++
++static int kw_mmc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, struct mmc_data *data)
++{
++ int timeout = 10;
++ int err;
++ ushort waittype = 0;
++ ushort resptype = 0;
++ ushort xfertype = 0;
++ ushort resp_indx = 0;
++
++#ifdef CONFIG_MMC_DEBUG
++ printf("cmdidx [0x%x] resp_type[0x%x] cmdarg[0x%x]\n", cmd->cmdidx, cmd->resp_type, cmd->cmdarg);
++#endif
++
++ udelay(10000);
++
++#ifdef CONFIG_MMC_DEBUG
++ printf("%s: cmd %d (hw state 0x%04x)\n", DRIVER_NAME, cmd->cmdidx, kwsd_read(SDIO_HW_STATE));
++#endif
++
++ /* Checking if card is busy */
++ while ((kwsd_read(SDIO_HW_STATE) & CARD_BUSY)) {
++ if (timeout == 0) {
++ printf("%s: card busy!\n", DRIVER_NAME);
++ return -1;
++ }
++ timeout--;
++ udelay(1000);
++ }
++
++ /* Set up for a data transfer if we have one */
++ if (data) {
++ if ((err = kw_mmc_setup_data(data)))
++ return err;
++ }
++
++ resptype = SDIO_CMD_INDEX(cmd->cmdidx);
++
++ /* Analyzing resptype/xfertype/waittype for the command */
++ if (cmd->resp_type & MMC_RSP_BUSY)
++ resptype |= SDIO_CMD_RSP_48BUSY;
++ else if (cmd->resp_type & MMC_RSP_136)
++ resptype |= SDIO_CMD_RSP_136;
++ else if (cmd->resp_type & MMC_RSP_PRESENT)
++ resptype |= SDIO_CMD_RSP_48;
++ else
++ resptype |= SDIO_CMD_RSP_NONE;
++
++ if (cmd->resp_type & MMC_RSP_CRC)
++ resptype |= SDIO_CMD_CHECK_CMDCRC;
++
++ if (cmd->resp_type & MMC_RSP_OPCODE)
++ resptype |= SDIO_CMD_INDX_CHECK;
++
++ if (cmd->resp_type & MMC_RSP_PRESENT) {
++ resptype |= SDIO_UNEXPECTED_RESP;
++ waittype |= SDIO_NOR_UNEXP_RSP;
++ }
++
++ if (data) {
++ resptype |= SDIO_CMD_DATA_PRESENT | SDIO_CMD_CHECK_DATACRC16;
++ xfertype |= SDIO_XFER_MODE_HW_WR_DATA_EN;
++ if (data->flags & MMC_DATA_READ) {
++ xfertype |= SDIO_XFER_MODE_TO_HOST;
++ waittype = SDIO_NOR_DMA_INI;
++ } else
++ waittype |= SDIO_NOR_XFER_DONE;
++ } else
++ waittype |= SDIO_NOR_CMD_DONE;
++
++ /* Setting cmd arguments */
++ kwsd_write(SDIO_ARG_LOW, cmd->cmdarg & 0xffff);
++ kwsd_write(SDIO_ARG_HI, cmd->cmdarg >> 16);
++
++ /* Setting Xfer mode */
++ kwsd_write(SDIO_XFER_MODE, xfertype);
++
++ kwsd_write(SDIO_NOR_INTR_STATUS, ~SDIO_NOR_CARD_INT);
++ kwsd_write(SDIO_ERR_INTR_STATUS, SDIO_POLL_MASK);
++
++ /* Sending command */
++ kwsd_write(SDIO_CMD, resptype);
++/*
++ kwsd_write(SDIO_CMD, KW_MMC_MAKE_CMD(cmd->cmdidx, resptype));
++*/
++
++ kwsd_write(SDIO_NOR_INTR_EN, SDIO_POLL_MASK);
++ kwsd_write(SDIO_ERR_INTR_EN, SDIO_POLL_MASK);
++
++ /* Waiting for completion */
++ timeout = 1000000;
++
++ while (!((kwsd_read(SDIO_NOR_INTR_STATUS)) & waittype)) {
++ if (kwsd_read(SDIO_NOR_INTR_STATUS) & SDIO_NOR_ERROR) {
++#ifdef DEBUG
++ printf("%s: kw_mmc_send_cmd: error! cmdidx : %d, err reg: %04x\n", DRIVER_NAME, cmd->cmdidx,
++wsd_read(SDIO_ERR_INTR_STATUS));
++#endif
++ if (kwsd_read(SDIO_ERR_INTR_STATUS) & (SDIO_ERR_CMD_TIMEOUT | SDIO_ERR_DATA_TIMEOUT)) {
++ return -ETIMEDOUT;
++ }
++ return -ECOMM;
++ }
++
++ timeout--;
++ udelay(1);
++ if (timeout <= 0) {
++ printf("%s: command timed out\n", DRIVER_NAME);
++ return -ETIMEDOUT;
++ }
++ }
++
++ /* Handling response */
++ if (cmd->resp_type & MMC_RSP_136) {
++ uint response[8];
++ for (resp_indx = 0; resp_indx < 8; resp_indx++)
++ response[resp_indx] = kwsd_read(SDIO_RSP(resp_indx));
++
++ cmd->response[0] = ((response[0] & 0x03ff) << 22) |
++ ((response[1] & 0xffff) << 6) |
++ ((response[2] & 0xfc00) >> 10);
++ cmd->response[1] = ((response[2] & 0x03ff) << 22) |
++ ((response[3] & 0xffff) << 6) |
++ ((response[4] & 0xfc00) >> 10);
++ cmd->response[2] = ((response[4] & 0x03ff) << 22) |
++ ((response[5] & 0xffff) << 6) |
++ ((response[6] & 0xfc00) >> 10);
++ cmd->response[3] = ((response[6] & 0x03ff) << 22) |
++ ((response[7] & 0x3fff) << 8);
++ } else if (cmd->resp_type & MMC_RSP_PRESENT) {
++ uint response[3];
++ for (resp_indx = 0; resp_indx < 3; resp_indx++)
++ response[resp_indx] = kwsd_read(SDIO_RSP(resp_indx));
++
++ cmd->response[0] = ((response[2] & 0x003f) << (8 - 8)) |
++ ((response[1] & 0xffff) << (14 - 8)) |
++ ((response[0] & 0x03ff) << (30 - 8));
++ cmd->response[1] = ((response[0] & 0xfc00) >> 10);
++ cmd->response[2] = 0;
++ cmd->response[3] = 0;
++ }
++
++#ifdef CONFIG_MMC_DEBUG
++ printf("%s: resp[0x%x] ", DRIVER_NAME, cmd->resp_type);
++ printf("[0x%x] ", cmd->response[0]);
++ printf("[0x%x] ", cmd->response[1]);
++ printf("[0x%x] ", cmd->response[2]);
++ printf("[0x%x] ", cmd->response[3]);
++ printf("\n");
++#endif
++
++ return 0;
++}
++
++#if 0
++/* Disable these three functions as they are not used anyway */
++
++static void kwsd_power_up(void)
++{
++#ifdef DEBUG
++ printf("%s: power up\n", DRIVER_NAME);
++#endif
++ /* disable interrupts */
++ kwsd_write(SDIO_NOR_INTR_EN, 0);
++ kwsd_write(SDIO_ERR_INTR_EN, 0);
++
++ /* SW reset */
++ kwsd_write(SDIO_SW_RESET, SDIO_SW_RESET_NOW);
++
++ kwsd_write(SDIO_XFER_MODE, 0);
++
++ /* enable status */
++ kwsd_write(SDIO_NOR_STATUS_EN, SDIO_POLL_MASK);
++ kwsd_write(SDIO_ERR_STATUS_EN, SDIO_POLL_MASK);
++
++ /* enable interrupts status */
++ kwsd_write(SDIO_NOR_INTR_STATUS, SDIO_POLL_MASK);
++ kwsd_write(SDIO_ERR_INTR_STATUS, SDIO_POLL_MASK);
++}
++
++static void kwsd_power_down(void)
++{
++#ifdef DEBUG
++ printf("%s: power down\n", DRIVER_NAME);
++#endif
++ /* disable interrupts */
++ kwsd_write(SDIO_NOR_INTR_EN, 0);
++ kwsd_write(SDIO_ERR_INTR_EN, 0);
++
++ /* SW reset */
++ kwsd_write(SDIO_SW_RESET, SDIO_SW_RESET_NOW);
++
++ kwsd_write(SDIO_XFER_MODE, SDIO_XFER_MODE_STOP_CLK);
++
++ /* disable status */
++ kwsd_write(SDIO_NOR_STATUS_EN, 0);
++ kwsd_write(SDIO_ERR_STATUS_EN, 0);
++
++ /* enable interrupts status */
++ kwsd_write(SDIO_NOR_INTR_STATUS, SDIO_POLL_MASK);
++ kwsd_write(SDIO_ERR_INTR_STATUS, SDIO_POLL_MASK);
++}
++
++static u32 kw_mmc_get_base_clock(void)
++{
++ /* Original version did a check for board device id and revision id
++ * and assigned one of these clocks:
++ * KW_MMC_BASE_FAST_CLK_100 (revid == 0 && devid != MV88F6282_DEV_ID)
++ * KW_MMC_BASE_FAST_CLK_200 (revid != 0 || devid == MV88F6282_DEV_ID)
++ * However, this check was disabled and
++ * KW_MMC_BASE_FAST_CLOCK
++ * was returned in every case.
++ * Therefore, all of the dead logic was removed. */
++ return KW_MMC_BASE_FAST_CLOCK;
++}
++#endif /* #if 0 */
++
++static inline u32 kw_mmc_get_base_clock(void)
++{
++ /* get MMC base clock. If any logic other than just returning
++ * a fixed value is ever used, remove inline modifier. */
++
++ /* Possible values:
++ * - KW_MMC_BASE_FAST_CLOCK (166 MHz)
++ * - KW_MMC_BASE_FAST_CLK_100 (100 MHz)
++ * - KW_MMC_BASE_FAST_CLK_200 (200 MHz)
++ *
++ * Tests have shown that 200 MHz is more reliable than
++ * 166 MHz, so this value is used. */
++ return KW_MMC_BASE_FAST_CLK_200;
++}
++
++static void kw_mmc_set_clk(unsigned int clock)
++{
++ unsigned int m;
++
++ if (clock == 0) {
++#ifdef DEBUG
++ printf("%s: clock off\n", DRIVER_NAME);
++#endif
++ kwsd_write(SDIO_XFER_MODE, SDIO_XFER_MODE_STOP_CLK);
++ kwsd_write(SDIO_CLK_DIV, KW_MMC_BASE_DIV_MAX);
++ } else {
++ m = kw_mmc_get_base_clock() / (2 * clock) - 1;
++ if (m > KW_MMC_BASE_DIV_MAX)
++ m = KW_MMC_BASE_DIV_MAX;
++#ifdef DEBUG
++ printf("%s: kw_mmc_set_clk: base = %d dividor = 0x%x clock=%d\n", DRIVER_NAME,
++w_mmc_get_base_clock(), m, clock);
++#endif
++ kwsd_write(SDIO_CLK_DIV, m & KW_MMC_BASE_DIV_MAX);
++ }
++ udelay(10000);
++}
++
++static void kw_mmc_set_bus(unsigned int bus)
++{
++ u32 ctrl_reg = 0;
++
++ ctrl_reg = kwsd_read(SDIO_HOST_CTRL);
++ ctrl_reg &= ~SDIO_HOST_CTRL_DATA_WIDTH_4_BITS;
++
++ switch (bus) {
++ case 4:
++ ctrl_reg |= SDIO_HOST_CTRL_DATA_WIDTH_4_BITS;
++ break;
++ case 1:
++ default:
++ ctrl_reg |= SDIO_HOST_CTRL_DATA_WIDTH_1_BIT;
++ }
++ /* default transfer mode */
++ ctrl_reg |= SDIO_HOST_CTRL_BIG_ENDIAN;
++ ctrl_reg &= ~SDIO_HOST_CTRL_LSB_FIRST;
++
++ /* default to maximum timeout */
++ ctrl_reg |= SDIO_HOST_CTRL_TMOUT(SDIO_HOST_CTRL_TMOUT_MAX);
++
++ ctrl_reg |= SDIO_HOST_CTRL_PUSH_PULL_EN;
++
++ ctrl_reg |= SDIO_HOST_CTRL_CARD_TYPE_MEM_ONLY;
++
++ /*
++ * The HI_SPEED_EN bit is causing trouble with many (but not all)
++ * high speed SD, SDHC and SDIO cards. Not enabling that bit
++ * makes all cards work. So let's just ignore that bit for now
++ * and revisit this issue if problems for not enabling this bit
++ * are ever reported.
++ */
++#if 0
++ if (ios->timing == MMC_TIMING_MMC_HS ||
++ ios->timing == MMC_TIMING_SD_HS)
++ ctrl_reg |= SDIO_HOST_CTRL_HI_SPEED_EN;
++#endif
++
++#ifdef DEBUG
++ printf("%s: ctrl 0x%04x: %s %s %s\n", DRIVER_NAME, ctrl_reg,
++ (ctrl_reg & SDIO_HOST_CTRL_PUSH_PULL_EN) ?
++ "push-pull" : "open-drain",
++ (ctrl_reg & SDIO_HOST_CTRL_DATA_WIDTH_4_BITS) ?
++ "4bit-width" : "1bit-width",
++ (ctrl_reg & SDIO_HOST_CTRL_HI_SPEED_EN) ?
++ "high-speed" : "");
++#endif
++
++ kwsd_write(SDIO_HOST_CTRL, ctrl_reg);
++ udelay(10000);
++}
++
++static void kw_mmc_set_ios(struct mmc *mmc)
++{
++#ifdef DEBUG
++ printf("%s: bus[%d] clock[%d]\n", DRIVER_NAME, mmc->bus_width, mmc->clock);
++#endif
++ kw_mmc_set_bus(mmc->bus_width);
++ kw_mmc_set_clk(mmc->clock);
++}
++
++static int kw_mmc_init(struct mmc *mmc)
++{
++#ifdef DEBUG
++ printf("%s: kw_mmc_init\n", DRIVER_NAME);
++#endif
++
++ /*
++ * Setting host parameters
++ * Initial Host Ctrl : Timeout : max , Normal Speed mode, 4-bit data mode
++ * Big Endian, SD memory Card, Push_pull CMD Line
++ */
++ kwsd_write(SDIO_HOST_CTRL,
++ SDIO_HOST_CTRL_TMOUT(SDIO_HOST_CTRL_TMOUT_MAX) |
++ SDIO_HOST_CTRL_DATA_WIDTH_4_BITS |
++ SDIO_HOST_CTRL_BIG_ENDIAN |
++ SDIO_HOST_CTRL_PUSH_PULL_EN |
++ SDIO_HOST_CTRL_CARD_TYPE_MEM_ONLY);
++
++ kwsd_write(SDIO_CLK_CTRL, 0);
++
++ /* enable status */
++ kwsd_write(SDIO_NOR_STATUS_EN, SDIO_POLL_MASK);
++ kwsd_write(SDIO_ERR_STATUS_EN, SDIO_POLL_MASK);
++
++ /* disable interrupts */
++ kwsd_write(SDIO_NOR_INTR_EN, 0);
++ kwsd_write(SDIO_ERR_INTR_EN, 0);
++
++ /* SW reset */
++ kwsd_write(SDIO_SW_RESET, SDIO_SW_RESET_NOW);
++
++ udelay(10000);
++ return 0;
++}
++
++int kw_mmc_initialize(bd_t *bis)
++{
++ struct mmc *mmc = NULL;
++ struct mmc_config *cfg = NULL;
++ struct mmc_ops *ops = NULL;
++ char *name = NULL;
++
++#ifdef DEBUG
++ printf("%s: %s base_clock = %d\n", DRIVER_NAME, kirkwood_id(), kw_mmc_get_base_clock());
++#endif
++ mmc = malloc(sizeof(struct mmc));
++ if (!mmc)
++ return -1;
++ memset(mmc, 0, sizeof(*mmc));
++
++ cfg = malloc(sizeof(*cfg));
++ if (cfg == NULL)
++ return -1;
++ memset(cfg, 0, sizeof(*cfg));
++ mmc->cfg = cfg; /* provided configuration */
++
++ ops = malloc(sizeof(*ops));
++ if (ops == NULL)
++ return -1;
++ memset(ops, 0, sizeof(*ops));
++ cfg->ops = ops;
++
++ name = malloc(sizeof(DRIVER_NAME)+1);
++ if (name == NULL)
++ return -1;
++ cfg->name = name;
++
++ sprintf(cfg->name, DRIVER_NAME);
++
++ ops->send_cmd = kw_mmc_send_cmd;
++ ops->set_ios = kw_mmc_set_ios;
++ ops->init = kw_mmc_init;
++
++ cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34;
++ cfg->host_caps = MMC_MODE_4BIT | MMC_MODE_HS;
++
++ cfg->f_min = kw_mmc_get_base_clock()/KW_MMC_BASE_DIV_MAX;
++ cfg->f_max = KW_MMC_CLOCKRATE_MAX;
++ cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT;
++
++ mmc = mmc_create (cfg, NULL);
++
++ if (mmc == NULL) {
++ free(name);
++ free(ops);
++ free(cfg);
++ printf("\nFailed to Initialize MMC\n");
++ return -1;
++ }
++
++ return 0;
++}
+--- a/include/configs/mv-common.h
++++ b/include/configs/mv-common.h
+@@ -130,4 +130,16 @@
+ #define CONFIG_MTD_PARTITIONS
+ #endif
+
++/*
++ * Kirkwood MMC
++ */
++#if defined(CONFIG_KIRKWOOD) && defined(CONFIG_CMD_MMC)
++#define CONFIG_SYS_MMC_BASE KW_SDIO_BASE
++#endif /* defined(CONFIG_KIRKWOOD) && defined(CONFIG_CMD_MMC) */
++
++/*
++ * GPIO command for all Kirkwood boxes
++ */
++#define CONFIG_CMD_GPIO
++
+ #endif /* _MV_COMMON_H */
+--- /dev/null
++++ b/include/configs/pogoplugv4.h
+@@ -0,0 +1,132 @@
++/*
++ * Copyright (C) 2014-2016 bodhi <mibodhi@gmail.com>
++ * Based on
++ *
++ * Copyright (C) 2012
++ * David Purdy <david.c.purdy@gmail.com>
++ *
++ * Based on Kirkwood support:
++ * (C) Copyright 2009
++ * Marvell Semiconductor <www.marvell.com>
++ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
++ *
++ * See file CREDITS for list of people who contributed to this
++ * project.
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License as
++ * published by the Free Software Foundation; either version 2 of
++ * the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; If not, see <http://www.gnu.org/licenses/>.
++ */
++
++#ifndef _CONFIG_POGOPLUGV4_H
++#define _CONFIG_POGOPLUGV4_H
++
++/*
++ * Machine type definition and ID
++ */
++#define MACH_TYPE_POGOPLUGV4 3960
++#define CONFIG_MACH_TYPE MACH_TYPE_POGOPLUGV4
++
++/*
++ * High Level Configuration Options (easy to change)
++ */
++#define CONFIG_FEROCEON_88FR131 /* #define CPU Core subversion */
++#define CONFIG_KW88F6192 /* SOC Name */
++#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
++
++/*
++ * Commands configuration
++ */
++
++#define CONFIG_SYS_LONGHELP
++#define CONFIG_PREBOOT
++
++/*
++ * mv-common.h should be defined after CMD configs since it used them
++ * to enable certain macros
++ */
++#include "mv-common.h"
++
++/*
++ * Environment variables configurations
++ */
++#ifdef CONFIG_CMD_NAND
++
++#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
++
++
++#endif
++
++#define CONFIG_ENV_SIZE 0x20000 /* 128k */
++#define CONFIG_ENV_ADDR 0x1c0000
++#define CONFIG_ENV_OFFSET 0x1c0000 /* env starts here */
++
++/*
++ * Default environment variables
++ */
++#define CONFIG_BOOTCOMMAND \
++ "usb reset ; " \
++ "fatload usb 0:1 0x2000000 initramfs.bin ; "\
++ "bootm 0x2000000 ; " \
++ "ubi part ubi; " \
++ "ubi read 0x800000 kernel; " \
++ "bootm 0x800000"
++
++#define CONFIG_MTDPARTS \
++ "mtdparts=orion_nand:" \
++ "0x1c0000(uboot)," \
++ "0x40000(uboot_env)," \
++ "0x7e00000(ubi)\0"
++
++#define CONFIG_EXTRA_ENV_SETTINGS \
++ "console=console=ttyS0,115200\0" \
++ "mtdids=nand0=orion_nand\0" \
++ "mtdparts="CONFIG_MTDPARTS \
++ "bootargs_root=\0"
++
++/*
++ * Ethernet Driver configuration
++ */
++#ifdef CONFIG_CMD_NET
++#define CONFIG_NETCONSOLE
++#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
++#define CONFIG_PHY_BASE_ADR 0
++#endif /* CONFIG_CMD_NET */
++
++/*
++ * File system
++ */
++#define CONFIG_JFFS2_NAND
++#define CONFIG_JFFS2_LZO
++#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
++#define CONFIG_MTD_PARTITIONS
++
++/*
++ * SATA
++ */
++#ifdef CONFIG_MVSATA_IDE
++#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
++#endif
++
++/*
++ * Date Time
++ */
++#ifdef CONFIG_CMD_DATE
++#define CONFIG_RTC_MV
++#endif /* CONFIG_CMD_DATE */
++
++/*
++ * Kirkwood GPIO
++ */
++#define CONFIG_KIRKWOOD_GPIO
++
++#endif /* _CONFIG_POGOPLUGV4_H */
+--- /dev/null
++++ b/include/kirkwood_mmc.h
+@@ -0,0 +1,268 @@
++/*
++ * (C) Copyright 2014 <ebbes.ebbes@gmail.com>
++ *
++ * Based on
++ *
++ * (C) Copyright 2012
++ * Marvell Semiconductor <www.marvell.com>
++ * Written-by: Gérald Kerma <uboot at doukki.net>
++ * See file CREDITS for list of people who contributed to this
++ * project.
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License as
++ * published by the Free Software Foundation; either version 2 of
++ * the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
++ * MA 02111-1307 USA
++ */
++
++#ifndef __KIRKWOOD_MMC_H__
++#define __KIRKWOOD_MMC_H__
++
++/*
++ * Clock rates
++ */
++
++#define KW_MMC_CLOCKRATE_MAX 50000000
++#define KW_MMC_BASE_DIV_MAX 0x7ff
++#define KW_MMC_BASE_FAST_CLOCK CONFIG_SYS_TCLK
++#define KW_MMC_BASE_FAST_CLK_100 100000000
++#define KW_MMC_BASE_FAST_CLK_200 200000000
++
++/*
++ * Macros
++ */
++#define kwsd_write(offs, val) writel(val, CONFIG_SYS_MMC_BASE + (offs))
++#define kwsd_read(offs) readl(CONFIG_SYS_MMC_BASE + (offs))
++
++#define KW_MMC_MAKE_CMD(c, f) (((c & 0xff) << 8) | (f & 0xff))
++
++/* SDIO register */
++#define SDIO_SYS_ADDR_LOW 0x000
++#define SDIO_SYS_ADDR_HI 0x004
++#define SDIO_BLK_SIZE 0x008
++#define SDIO_BLK_COUNT 0x00c
++#define SDIO_ARG_LOW 0x010
++#define SDIO_ARG_HI 0x014
++#define SDIO_XFER_MODE 0x018
++#define SDIO_CMD 0x01c
++#define SDIO_RSP(i) (0x020 + ((i)<<2))
++#define SDIO_RSP0 0x020
++#define SDIO_RSP1 0x024
++#define SDIO_RSP2 0x028
++#define SDIO_RSP3 0x02c
++#define SDIO_RSP4 0x030
++#define SDIO_RSP5 0x034
++#define SDIO_RSP6 0x038
++#define SDIO_RSP7 0x03c
++#define SDIO_BUF_DATA_PORT 0x040
++#define SDIO_RSVED 0x044
++#define SDIO_HW_STATE 0x048
++#define SDIO_PRESENT_STATE0 0x048
++#define SDIO_PRESENT_STATE1 0x04c
++#define SDIO_HOST_CTRL 0x050
++#define SDIO_BLK_GAP_CTRL 0x054
++#define SDIO_CLK_CTRL 0x058
++#define SDIO_SW_RESET 0x05c
++#define SDIO_NOR_INTR_STATUS 0x060
++#define SDIO_ERR_INTR_STATUS 0x064
++#define SDIO_NOR_STATUS_EN 0x068
++#define SDIO_ERR_STATUS_EN 0x06c
++#define SDIO_NOR_INTR_EN 0x070
++#define SDIO_ERR_INTR_EN 0x074
++#define SDIO_AUTOCMD12_ERR_STATUS 0x078
++#define SDIO_CURR_BYTE_LEFT 0x07c
++#define SDIO_CURR_BLK_LEFT 0x080
++#define SDIO_AUTOCMD12_ARG_LOW 0x084
++#define SDIO_AUTOCMD12_ARG_HI 0x088
++#define SDIO_AUTOCMD12_INDEX 0x08c
++#define SDIO_AUTO_RSP(i) (0x090 + ((i)<<2))
++#define SDIO_AUTO_RSP0 0x090
++#define SDIO_AUTO_RSP1 0x094
++#define SDIO_AUTO_RSP2 0x098
++#define SDIO_CLK_DIV 0x128
++
++#define WINDOW_CTRL(i) (0x108 + ((i) << 3))
++#define WINDOW_BASE(i) (0x10c + ((i) << 3))
++
++/* SDIO_PRESENT_STATE */
++#define CARD_BUSY (1 << 1)
++#define CMD_INHIBIT (1 << 0)
++#define CMD_TXACTIVE (1 << 8)
++#define CMD_RXACTIVE (1 << 9)
++#define CMD_AUTOCMD12ACTIVE (1 << 14)
++#define CMD_BUS_BUSY (CMD_AUTOCMD12ACTIVE | \
++ CMD_RXACTIVE | \
++ CMD_TXACTIVE | \
++ CMD_INHIBIT | \
++ CARD_BUSY)
++
++/*
++ * SDIO_CMD
++ */
++
++#define SDIO_CMD_RSP_NONE (0 << 0)
++#define SDIO_CMD_RSP_136 (1 << 0)
++#define SDIO_CMD_RSP_48 (2 << 0)
++#define SDIO_CMD_RSP_48BUSY (3 << 0)
++
++#define SDIO_CMD_CHECK_DATACRC16 (1 << 2)
++#define SDIO_CMD_CHECK_CMDCRC (1 << 3)
++#define SDIO_CMD_INDX_CHECK (1 << 4)
++#define SDIO_CMD_DATA_PRESENT (1 << 5)
++#define SDIO_UNEXPECTED_RESP (1 << 7)
++
++#define SDIO_CMD_INDEX(x) ((x) << 8)
++
++/*
++ * SDIO_XFER_MODE
++ */
++
++#define SDIO_XFER_MODE_STOP_CLK (1 << 5)
++#define SDIO_XFER_MODE_HW_WR_DATA_EN (1 << 1)
++#define SDIO_XFER_MODE_AUTO_CMD12 (1 << 2)
++#define SDIO_XFER_MODE_INT_CHK_EN (1 << 3)
++#define SDIO_XFER_MODE_TO_HOST (1 << 4)
++#define SDIO_XFER_MODE_DMA (0 << 6)
++
++/*
++ * SDIO_HOST_CTRL
++ */
++
++#define SDIO_HOST_CTRL_PUSH_PULL_EN (1 << 0)
++
++#define SDIO_HOST_CTRL_CARD_TYPE_MEM_ONLY (0 << 1)
++#define SDIO_HOST_CTRL_CARD_TYPE_IO_ONLY (1 << 1)
++#define SDIO_HOST_CTRL_CARD_TYPE_IO_MEM_COMBO (2 << 1)
++#define SDIO_HOST_CTRL_CARD_TYPE_IO_MMC (3 << 1)
++#define SDIO_HOST_CTRL_CARD_TYPE_MASK (3 << 1)
++
++#define SDIO_HOST_CTRL_BIG_ENDIAN (1 << 3)
++#define SDIO_HOST_CTRL_LSB_FIRST (1 << 4)
++#define SDIO_HOST_CTRL_DATA_WIDTH_1_BIT (0 << 9)
++#define SDIO_HOST_CTRL_DATA_WIDTH_4_BITS (1 << 9)
++#define SDIO_HOST_CTRL_HI_SPEED_EN (1 << 10)
++
++#define SDIO_HOST_CTRL_TMOUT_MAX 0xf
++#define SDIO_HOST_CTRL_TMOUT_MASK (0xf << 11)
++#define SDIO_HOST_CTRL_TMOUT(x) ((x) << 11)
++#define SDIO_HOST_CTRL_TMOUT_EN (1 << 15)
++
++/*
++ * SDIO_SW_RESET
++ */
++
++#define SDIO_SW_RESET_NOW (1 << 8)
++
++/*
++ * Normal interrupt status bits
++ */
++
++#define SDIO_NOR_ERROR (1 << 15)
++#define SDIO_NOR_UNEXP_RSP (1 << 14)
++#define SDIO_NOR_AUTOCMD12_DONE (1 << 13)
++#define SDIO_NOR_SUSPEND_ON (1 << 12)
++#define SDIO_NOR_LMB_FF_8W_AVAIL (1 << 11)
++#define SDIO_NOR_LMB_FF_8W_FILLED (1 << 10)
++#define SDIO_NOR_READ_WAIT_ON (1 << 9)
++#define SDIO_NOR_CARD_INT (1 << 8)
++#define SDIO_NOR_READ_READY (1 << 5)
++#define SDIO_NOR_WRITE_READY (1 << 4)
++#define SDIO_NOR_DMA_INI (1 << 3)
++#define SDIO_NOR_BLK_GAP_EVT (1 << 2)
++#define SDIO_NOR_XFER_DONE (1 << 1)
++#define SDIO_NOR_CMD_DONE (1 << 0)
++
++/*
++ * Error status bits
++ */
++
++#define SDIO_ERR_CRC_STATUS (1 << 14)
++#define SDIO_ERR_CRC_STARTBIT (1 << 13)
++#define SDIO_ERR_CRC_ENDBIT (1 << 12)
++#define SDIO_ERR_RESP_TBIT (1 << 11)
++#define SDIO_ERR_XFER_SIZE (1 << 10)
++#define SDIO_ERR_CMD_STARTBIT (1 << 9)
++#define SDIO_ERR_AUTOCMD12 (1 << 8)
++#define SDIO_ERR_DATA_ENDBIT (1 << 6)
++#define SDIO_ERR_DATA_CRC (1 << 5)
++#define SDIO_ERR_DATA_TIMEOUT (1 << 4)
++#define SDIO_ERR_CMD_INDEX (1 << 3)
++#define SDIO_ERR_CMD_ENDBIT (1 << 2)
++#define SDIO_ERR_CMD_CRC (1 << 1)
++#define SDIO_ERR_CMD_TIMEOUT (1 << 0)
++#define SDIO_POLL_MASK 0xffff /* enable all for polling */
++
++#define MMC_BLOCK_SIZE 512
++
++/*
++ * CMD12 error status bits
++ */
++
++#define SDIO_AUTOCMD12_ERR_NOTEXE (1 << 0)
++#define SDIO_AUTOCMD12_ERR_TIMEOUT (1 << 1)
++#define SDIO_AUTOCMD12_ERR_CRC (1 << 2)
++#define SDIO_AUTOCMD12_ERR_ENDBIT (1 << 3)
++#define SDIO_AUTOCMD12_ERR_INDEX (1 << 4)
++#define SDIO_AUTOCMD12_ERR_RESP_T_BIT (1 << 5)
++#define SDIO_AUTOCMD12_ERR_RESP_STARTBIT (1 << 6)
++
++#define MMC_RSP_PRESENT (1 << 0)
++#define MMC_RSP_136 (1 << 1) /* 136 bit response */
++#define MMC_RSP_CRC (1 << 2) /* expect valid crc */
++#define MMC_RSP_BUSY (1 << 3) /* card may send busy */
++#define MMC_RSP_OPCODE (1 << 4) /* response contains opcode */
++
++#define MMC_BUSMODE_OPENDRAIN 1
++#define MMC_BUSMODE_PUSHPULL 2
++
++#define MMC_BUS_WIDTH_1 0
++#define MMC_BUS_WIDTH_4 2
++#define MMC_BUS_WIDTH_8 3
++
++#define MMC_CAP_4_BIT_DATA (1 << 0) /* Can the host do 4 bit transfers */
++#define MMC_CAP_MMC_HIGHSPEED (1 << 1) /* Can do MMC high-speed timing */
++#define MMC_CAP_SD_HIGHSPEED (1 << 2) /* Can do SD high-speed timing */
++#define MMC_CAP_SDIO_IRQ (1 << 3) /* Can signal pending SDIO IRQs */
++#define MMC_CAP_SPI (1 << 4) /* Talks only SPI protocols */
++#define MMC_CAP_NEEDS_POLL (1 << 5) /* Needs polling for card-detection */
++#define MMC_CAP_8_BIT_DATA (1 << 6) /* Can the host do 8 bit transfers */
++
++#define MMC_CAP_NONREMOVABLE (1 << 8) /* Nonremovable e.g. eMMC */
++#define MMC_CAP_WAIT_WHILE_BUSY (1 << 9) /* Waits while card is busy */
++#define MMC_CAP_ERASE (1 << 10) /* Allow erase/trim commands */
++#define MMC_CAP_1_8V_DDR (1 << 11) /* can support */
++ /* DDR mode at 1.8V */
++#define MMC_CAP_1_2V_DDR (1 << 12) /* can support */
++ /* DDR mode at 1.2V */
++#define MMC_CAP_POWER_OFF_CARD (1 << 13) /* Can power off after boot */
++#define MMC_CAP_BUS_WIDTH_TEST (1 << 14) /* CMD14/CMD19 bus width ok */
++#define MMC_CAP_UHS_SDR12 (1 << 15) /* Host supports UHS SDR12 mode */
++#define MMC_CAP_UHS_SDR25 (1 << 16) /* Host supports UHS SDR25 mode */
++#define MMC_CAP_UHS_SDR50 (1 << 17) /* Host supports UHS SDR50 mode */
++#define MMC_CAP_UHS_SDR104 (1 << 18) /* Host supports UHS SDR104 mode */
++#define MMC_CAP_UHS_DDR50 (1 << 19) /* Host supports UHS DDR50 mode */
++#define MMC_CAP_DRIVER_TYPE_A (1 << 23) /* Host supports Driver Type A */
++#define MMC_CAP_DRIVER_TYPE_C (1 << 24) /* Host supports Driver Type C */
++#define MMC_CAP_DRIVER_TYPE_D (1 << 25) /* Host supports Driver Type D */
++#define MMC_CAP_CMD23 (1 << 30) /* CMD23 supported. */
++#define MMC_CAP_HW_RESET (1 << 31) /* Hardware reset */
++
++/*
++ * Functions prototypes
++ *
++ * Original patch had static function declarations in this header file.
++ * Those should rather not be declared in the header as they only cause compiler warnings.
++ */
++int kw_mmc_initialize(bd_t *bis);
++
++#endif /* __KIRKWOOD_MMC_H__ */
projects / openwrt / staging / kaloz.git / commitdiff