realtek: add support for HPE 1920-8g-poe+ (65W)

Hardware information:
---------------------

- RTL8380 SoC
- 8 Gigabit RJ45 PoE ports (built-in RTL8218B)
- 2 SFP ports (built-in SerDes)
- RJ45 RS232 port on front panel
- 32 MiB NOR Flash
- 128 MiB DDR3 DRAM
- PT7A7514 watchdog
- PoE chip
- Fanless

Known issues:
---------------------
- PoE LEDs are uncontrolled.

(Manual taken from f2f09bc)
Booting initramfs image:
------------------------

- Prepare a FTP or TFTP server serving the OpenWrt initramfs image and
  connect the server to a switch port.

- Connect to the console port of the device and enter the extended
  boot menu by typing Ctrl+B when prompted.

- Choose the menu option "<3> Enter Ethernet SubMenu".

- Set network parameters via the option "<5> Modify Ethernet Parameter".
  Enter the FTP/TFTP filename as "Load File Name" ("Target File Name"
  can be left blank, it is not required for booting from RAM). Note that
  the configuration is saved on flash, so it only needs to be done once.

- Select "<1> Download Application Program To SDRAM And Run".

Initial installation:
---------------------

- Boot an initramfs image as described above, then use sysupgrade to
  install OpenWrt permanently. After initial installation, the
  bootloader needs to be configured to load the correct image file

- Enter the extended boot menu again and choose "<4> File Control",
  then select "<2> Set Application File type".

- Enter the number of the file "openwrt-kernel.bin" (should be 1), and
  use the option "<1> +Main" to select it as boot image.

- Choose "<0> Exit To Main Menu" and then "<1> Boot System".

NOTE: The bootloader on these devices can only boot from the VFS
filesystem which normally spans most of the flash. With OpenWrt, only
the first part of the firmware partition contains a valid filesystem,
the rest is used for rootfs. As the bootloader does not know about this,
you must not do any file operations in the bootloader, as this may
corrupt the OpenWrt installation (selecting the boot image is an
exception, as it only stores a flag in the bootloader data, but doesn't
write to the filesystem).

Example PoE config file (/etc/config/poe):
---------------------
config global
        option budget   '65'

config port
        option enable   '1'
        option id       '1'
        option name     'lan8'
        option poe_plus '1'
        option priority '2'
config port
        option enable   '1'
        option id       '2'
        option name     'lan7'
        option poe_plus '1'
        option priority '2'
config port
        option enable   '1'
        option id       '3'
        option name     'lan6'
        option poe_plus '1'
        option priority '2'
config port
        option enable   '1'
        option id       '4'
        option name     'lan5'
        option poe_plus '1'
        option priority '2'
config port
        option enable   '1'
        option id       '5'
        option name     'lan4'
        option poe_plus '1'
        option priority '2'
config port
        option enable   '1'
        option id       '6'
        option name     'lan3'
        option poe_plus '1'
        option priority '2'
config port
        option enable   '1'
        option id       '7'
        option name     'lan2'
        option poe_plus '1'
        option priority '2'
config port
        option enable   '1'
        option id       '8'
        option name     'lan1'
        option poe_plus '1'
        option priority '2'

Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl>

diff --git a/target/linux/realtek/base-files/etc/board.d/02_network b/target/linux/realtek/base-files/etc/board.d/02_network
index 84d3e68e48f3186a8a3ac3db5d92bfffd79211a7..45bc2196d405a5a6aa03bf291608b99756938f58 100644 (file)
--- a/target/linux/realtek/base-files/etc/board.d/02_network
+++ b/target/linux/realtek/base-files/etc/board.d/02_network
@@ -31,6 +31,7 @@ lan_mac_end=""
 label_mac=""
 case $board in
 hpe,1920-8g|\
+hpe,1920-8g-poe-65w|\
 hpe,1920-8g-poe-180w|\
 hpe,1920-16g|\
 hpe,1920-24g)
@@ -67,6 +68,9 @@ done
 [ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac
 
 case $board in
+hpe,1920-8g-poe-65w)
+       ucidef_set_poe 65 "$lan_list_rev" "lan9 lan10"
+       ;;
 hpe,1920-8g-poe-180w)
        ucidef_set_poe 180 "$lan_list_rev" "lan9 lan10"
        ;;

diff --git a/target/linux/realtek/dts-5.15/rtl8380_hpe_1920-8g-poe-65w.dts b/target/linux/realtek/dts-5.15/rtl8380_hpe_1920-8g-poe-65w.dts
new file mode 100644 (file)
index 0000000..341f535
--- /dev/null
+++ b/target/linux/realtek/dts-5.15/rtl8380_hpe_1920-8g-poe-65w.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "rtl8380_hpe_1920-8g.dtsi"
+
+/ {
+       compatible = "hpe,1920-8g-poe-65w", "realtek,rtl838x-soc";
+       model = "HPE 1920-8G-PoE+ 65W (JG921A)";
+};
+
+&uart1 {
+       status = "okay";
+};

diff --git a/target/linux/realtek/image/rtl838x.mk b/target/linux/realtek/image/rtl838x.mk
index c0b9c70bb6f7c23190704c9f706dc83999c00582..09b4f3ebb03b73470f54535b935a471a7350d132 100644 (file)
--- a/target/linux/realtek/image/rtl838x.mk
+++ b/target/linux/realtek/image/rtl838x.mk
@@ -99,6 +99,15 @@ define Device/hpe_1920-8g
 endef
 TARGET_DEVICES += hpe_1920-8g
 
+define Device/hpe_1920-8g-poe-65w
+  $(Device/hpe_1920)
+  SOC := rtl8380
+  DEVICE_MODEL := 1920-8G-PoE+ 65W (JG921A)
+  DEVICE_PACKAGES += realtek-poe
+  H3C_DEVICE_ID := 0x00010024
+endef
+TARGET_DEVICES += hpe_1920-8g-poe-65w
+
 define Device/hpe_1920-8g-poe-180w
   $(Device/hpe_1920)
   SOC := rtl8380