+++ /dev/null
-config LTQ_DSL_ENABLE_SOAP
- bool "Enable SOAP support"
- depends on PACKAGE_ltq-dsl-app
- default n
-
-config LTQ_DSL_ENABLE_DSL_EVENT_POLLING
- bool "Include Event Polling support"
- depends on PACKAGE_ltq-dsl-app
- default n
Infineon DSL CPE API for Amazon SE, Danube and Vinax.
endef
-define Package/ltq-adsl-app/config
- source "$(SOURCE)/Config.in"
-endef
-
LTQ_DSL_MAX_DEVICE=1
LTQ_DSL_LINES_PER_DEVICE=1
LTQ_DSL_CHANNELS_PER_LINE=1
--enable-dsl-pm-line-thresholds \
--enable-dsl-pm-optional-parameters
-ifeq ($(CONFIG_LTQ_DSL_ENABLE_SOAP),y)
-CONFIGURE_ARGS += \
- --enable-soap-support
-endif
-
-ifeq ($(CONFIG_LTQ_DSL_ENABLE_DSL_EVENT_POLLING),y)
-CONFIGURE_ARGS += \
- --enable-dsl-event-polling
-endif
-
TARGET_CFLAGS += -I$(LINUX_DIR)/include
define Package/ltq-adsl-app/install
$(INSTALL_DIR) $(1)/sbin
$(INSTALL_BIN) $(PKG_BUILD_DIR)/src/dsl_cpe_control $(1)/sbin
- $(INSTALL_BIN) ./files/dsl_notify.sh $(1)/sbin
endef
$(eval $(call BuildPackage,ltq-adsl-app))
SERVICE_DAEMONIZE=1
SERVICE_WRITE_PID=1
-#
-# Basic functions to send CLI commands to the dsl_cpe_control daemon
-#
-dsl_cmd() {
- killall -0 dsl_cpe_control && (
- echo "$@" > /tmp/pipe/dsl_cpe0_cmd
- cat /tmp/pipe/dsl_cpe0_ack
- )
-}
-dsl_val() {
- echo $(expr "$1" : '.*'$2'=\([-\.[:alnum:]]*\).*')
-}
-
-#
-# Simple divide by 10 routine to cope with one decimal place
-#
-dbt() {
- local a=$(expr $1 / 10)
- local b=$(expr $1 % 10)
- echo "${a}.${b}"
-}
-#
-# Take a number and convert to k or meg
-#
-scale() {
- local val=$1
- local a
- local b
-
- if [ "$val" -gt 1000000 ]; then
- a=$(expr $val / 1000)
- b=$(expr $a % 1000)
- a=$(expr $a / 1000)
- printf "%d.%03d Mb" ${a} ${b}
- elif [ "$val" -gt 1000 ]; then
- a=$(expr $val / 1000)
- printf "%d Kb" ${a}
- else
- echo "${val} b"
- fi
-}
-
-#
-# Read the data rates for both directions
-#
-data_rates() {
- local csg
- local dru
- local drd
- local sdru
- local sdrd
-
- csg=$(dsl_cmd g997csg 0 1)
- drd=$(dsl_val "$csg" ActualDataRate)
-
- csg=$(dsl_cmd g997csg 0 0)
- dru=$(dsl_val "$csg" ActualDataRate)
-
- [ -z "$drd" ] && drd=0
- [ -z "$dru" ] && dru=0
-
- sdrd=$(scale $drd)
- sdru=$(scale $dru)
-
- if [ "$action" = "lucistat" ]; then
- echo "dsl.data_rate_down=$drd"
- echo "dsl.data_rate_up=$dru"
- echo "dsl.data_rate_down_s=\"$sdrd\""
- echo "dsl.data_rate_up_s=\"$sdru\""
- else
- echo "Data Rate: ${sdrd}/s / ${sdru}/s"
- fi
-}
-
-#
-# Chipset
-#
-chipset() {
- local vig
- local cs
- local csv
-
- vig=$(dsl_cmd vig)
- cs=$(dsl_val "$vig" DSL_ChipSetType)
- csv=$(dsl_val "$vig" DSL_ChipSetHWVersion)
-
- if [ "$action" = "lucistat" ]; then
- echo "dsl.chipset=\"${cs} ${csv}\""
- else
- echo "Chipset: ${cs} ${csv}"
- fi
-}
-
-#
-# Work out how long the line has been up
-#
-line_uptime() {
- local ccsg
- local et
- local etr
- local d
- local h
- local m
- local s
- local rc=""
-
- ccsg=$(dsl_cmd pmccsg 0 0 0)
- et=$(dsl_val "$ccsg" nElapsedTime)
-
- [ -z "$et" ] && et=0
-
- if [ "$action" = "lucistat" ]; then
- echo "dsl.line_uptime=${et}"
- return
- fi
-
- d=$(expr $et / 86400)
- etr=$(expr $et % 86400)
- h=$(expr $etr / 3600)
- etr=$(expr $etr % 3600)
- m=$(expr $etr / 60)
- s=$(expr $etr % 60)
-
-
- [ "${d}${h}${m}${s}" -ne 0 ] && rc="${s}s"
- [ "${d}${h}${m}" -ne 0 ] && rc="${m}m ${rc}"
- [ "${d}${h}" -ne 0 ] && rc="${h}h ${rc}"
- [ "${d}" -ne 0 ] && rc="${d}d ${rc}"
-
- [ -z "$rc" ] && rc="down"
- echo "Line Uptime: ${rc}"
-}
-
-#
-# Get noise and attenuation figures
-#
-line_data() {
- local lsg
- local latnu
- local latnd
- local snru
- local snrd
-
- lsg=$(dsl_cmd g997lsg 1 1)
- latnd=$(dsl_val "$lsg" LATN)
- snrd=$(dsl_val "$lsg" SNR)
-
- lsg=$(dsl_cmd g997lsg 0 1)
- latnu=$(dsl_val "$lsg" LATN)
- snru=$(dsl_val "$lsg" SNR)
-
- [ -z "$latnd" ] && latnd=0
- [ -z "$latnu" ] && latnu=0
- [ -z "$snrd" ] && snrd=0
- [ -z "$snru" ] && snru=0
-
- latnd=$(dbt $latnd)
- latnu=$(dbt $latnu)
- snrd=$(dbt $snrd)
- snru=$(dbt $snru)
-
- if [ "$action" = "lucistat" ]; then
- echo "dsl.line_attenuation_down=$latnd"
- echo "dsl.line_attenuation_up=$latnu"
- echo "dsl.noise_margin_down=$snrd"
- echo "dsl.noise_margin_up=$snru"
- else
- echo "Line Attenuation: ${latnd}dB / ${latnu}dB"
- echo "Noise Margin: ${snrd}dB / ${snru}dB"
- fi
-}
-
-#
-# Is the line up? Or what state is it in?
-#
-line_state() {
- local lsg=$(dsl_cmd lsg)
- local ls=$(dsl_val "$lsg" nLineState);
- local s;
-
- case "$ls" in
- "0x0") s="not initialized" ;;
- "0x1") s="exception" ;;
- "0x10") s="not updated" ;;
- "0xff") s="idle request" ;;
- "0x100") s="idle" ;;
- "0x1ff") s="silent request" ;;
- "0x200") s="silent" ;;
- "0x300") s="handshake" ;;
- "0x380") s="full_init" ;;
- "0x400") s="discovery" ;;
- "0x500") s="training" ;;
- "0x600") s="analysis" ;;
- "0x700") s="exchange" ;;
- "0x800") s="showtime_no_sync" ;;
- "0x801") s="showtime_tc_sync" ;;
- "0x900") s="fastretrain" ;;
- "0xa00") s="lowpower_l2" ;;
- "0xb00") s="loopdiagnostic active" ;;
- "0xb10") s="loopdiagnostic data exchange" ;;
- "0xb20") s="loopdiagnostic data request" ;;
- "0xc00") s="loopdiagnostic complete" ;;
- "0x1000000") s="test" ;;
- "0xd00") s="resync" ;;
- "0x3c0") s="short init entry" ;;
- "") s="not running daemon"; ls="0xfff" ;;
- *) s="unknown" ;;
- esac
-
- if [ $action = "lucistat" ]; then
- echo "dsl.line_state_num=$ls"
- echo "dsl.line_state_detail=\"$s\""
- if [ "$ls" = "0x801" ]; then
- echo "dsl.line_state=\"UP\""
- else
- echo "dsl.line_state=\"DOWN\""
- fi
- else
- if [ "$ls" = "0x801" ]; then
- echo "Line State: UP [$ls: $s]"
- else
- echo "Line State: DOWN [$ls: $s]"
- fi
- fi
-}
-
-#
-# Main status routine
-#
-status() {
- chipset
- line_state
- data_rates
- line_data
- line_uptime
-}
-
-#
-# Luci (lua) compatible version that's easy to parse
-#
-lucistat() {
- echo "local dsl={}"
- status
- echo "return dsl"
-}
-
+. /lib/functions/lantiq_dsl.sh
annex_b=10_00_10_00_00_04_00_00
annex_bdmt=10_00_00_00_00_00_00_00
annex_m2=00_00_00_00_40_00_00_00
annex_m2p=00_00_00_00_00_00_04_00
-#
-# Simple start routine
-#
start() {
local annex
local firmware
config_get annex wan annex
config_get firmware wan firmware
- # get xtu
eval "xtu=\"\${annex_$annex}\""
- # check for firmware
[ -z "${firmware}" ] &&
firmware=adsl.bin
- # start CPE dsl daemon in the background
service_start /sbin/dsl_cpe_control -i${xtu} \
-n /sbin/dsl_notify.sh \
-f /lib/firmware/${firmware}
}
-#
-# For stop we want to simulate the notification call for when
-# the line goes down, so that we can stop the ppp link before
-# we die.
-#
stop() {
DSL_NOTIFICATION_TYPE="DSL_INTERFACE_STATUS" \
DSL_INTERFACE_STATUS="DOWN" \
+++ /dev/null
-#!/bin/sh
-#
-# This script is called by dsl_cpe_control whenever there is a DSL event,
-# we only actually care about the DSL_INTERFACE_STATUS events as these
-# tell us the line has either come up or gone down.
-#
-# The rest of the code is basically the same at the atm hotplug code
-#
-
-[ "$DSL_NOTIFICATION_TYPE" = "DSL_INTERFACE_STATUS" ] || exit 0
-
-. /lib/functions.sh
-
-include /lib/network
-scan_interfaces
-
-local found=0
-local ifc
-for ifc in $interfaces; do
- local up
- config_get_bool up "$ifc" up 0
-
- local auto
- config_get_bool auto "$ifc" auto 1
-
- local proto
- config_get proto "$ifc" proto
-
- if [ "$DSL_INTERFACE_STATUS" = "UP" ]; then
- if [ "$proto" = "pppoa" ] && [ "$up" != 1 ] && [ "$auto" = 1 ]; then
- found=1
- ( sleep 1; ifup "$ifc" ) &
- fi
- else
- if [ "$proto" = "pppoa" ] && [ "$up" = 1 ] && [ "$auto" = 1 ]; then
- found=1
- ( sleep 1; ifdown "$ifc" ) &
- fi
- fi
-done
-
-if [ "$found" != 1 ]; then
- logger "Found no matching interface for DSL notification ($DSL_INTERFACE_STATUS)"
-fi
$(INSTALL_DIR) $(1)/sbin
$(INSTALL_BIN) $(PKG_BUILD_DIR)/src/dsl_cpe_control $(1)/sbin/vdsl_cpe_control
- $(INSTALL_BIN) ./files/dsl_notify.sh $(1)/sbin
endef
$(eval $(call BuildPackage,ltq-vdsl-app))
SERVICE_DAEMONIZE=1
SERVICE_WRITE_PID=1
-#
-# Basic functions to send CLI commands to the vdsl_cpe_control daemon
-#
-dsl_cmd() {
- killall -0 vdsl_cpe_control && (
- echo "$@" > /tmp/pipe/dsl_cpe0_cmd
- cat /tmp/pipe/dsl_cpe0_ack
- )
-}
-dsl_val() {
- echo $(expr "$1" : '.*'$2'=\([-\.[:alnum:]]*\).*')
-}
-
-#
-# Simple divide by 10 routine to cope with one decimal place
-#
-dbt() {
- local a=$(expr $1 / 10)
- local b=$(expr $1 % 10)
- echo "${a}.${b}"
-}
-#
-# Take a number and convert to k or meg
-#
-scale() {
- local val=$1
- local a
- local b
-
- if [ "$val" -gt 1000000 ]; then
- a=$(expr $val / 1000)
- b=$(expr $a % 1000)
- a=$(expr $a / 1000)
- printf "%d.%03d Mb" ${a} ${b}
- elif [ "$val" -gt 1000 ]; then
- a=$(expr $val / 1000)
- printf "%d Kb" ${a}
- else
- echo "${val} b"
- fi
-}
-
-#
-# Read the data rates for both directions
-#
-data_rates() {
- local csg
- local dru
- local drd
- local sdru
- local sdrd
-
- csg=$(dsl_cmd g997csg 0 1)
- drd=$(dsl_val "$csg" ActualDataRate)
-
- csg=$(dsl_cmd g997csg 0 0)
- dru=$(dsl_val "$csg" ActualDataRate)
-
- [ -z "$drd" ] && drd=0
- [ -z "$dru" ] && dru=0
-
- sdrd=$(scale $drd)
- sdru=$(scale $dru)
-
- if [ "$action" = "lucistat" ]; then
- echo "dsl.data_rate_down=$drd"
- echo "dsl.data_rate_up=$dru"
- echo "dsl.data_rate_down_s=\"$sdrd\""
- echo "dsl.data_rate_up_s=\"$sdru\""
- else
- echo "Data Rate: ${sdrd}/s / ${sdru}/s"
- fi
-}
+. /lib/functions/lantiq_dsl.sh
+XDSL_CTRL=vdsl_cpe_control
-#
-# Chipset
-#
-chipset() {
- local vig
- local cs
- local csv
-
- vig=$(dsl_cmd vig)
- cs=$(dsl_val "$vig" DSL_ChipSetType)
- csv=$(dsl_val "$vig" DSL_ChipSetHWVersion)
-
- if [ "$action" = "lucistat" ]; then
- echo "dsl.chipset=\"${cs} ${csv}\""
- else
- echo "Chipset: ${cs} ${csv}"
- fi
-}
-
-#
-# Work out how long the line has been up
-#
-line_uptime() {
- local ccsg
- local et
- local etr
- local d
- local h
- local m
- local s
- local rc=""
-
- ccsg=$(dsl_cmd pmccsg 0 0 0)
- et=$(dsl_val "$ccsg" nElapsedTime)
-
- [ -z "$et" ] && et=0
-
- if [ "$action" = "lucistat" ]; then
- echo "dsl.line_uptime=${et}"
- return
- fi
-
- d=$(expr $et / 86400)
- etr=$(expr $et % 86400)
- h=$(expr $etr / 3600)
- etr=$(expr $etr % 3600)
- m=$(expr $etr / 60)
- s=$(expr $etr % 60)
-
-
- [ "${d}${h}${m}${s}" -ne 0 ] && rc="${s}s"
- [ "${d}${h}${m}" -ne 0 ] && rc="${m}m ${rc}"
- [ "${d}${h}" -ne 0 ] && rc="${h}h ${rc}"
- [ "${d}" -ne 0 ] && rc="${d}d ${rc}"
-
- [ -z "$rc" ] && rc="down"
- echo "Line Uptime: ${rc}"
-}
-
-#
-# Get noise and attenuation figures
-#
-line_data() {
- local lsg
- local latnu
- local latnd
- local snru
- local snrd
-
- lsg=$(dsl_cmd g997lsg 1 1)
- latnd=$(dsl_val "$lsg" LATN)
- snrd=$(dsl_val "$lsg" SNR)
-
- lsg=$(dsl_cmd g997lsg 0 1)
- latnu=$(dsl_val "$lsg" LATN)
- snru=$(dsl_val "$lsg" SNR)
-
- [ -z "$latnd" ] && latnd=0
- [ -z "$latnu" ] && latnu=0
- [ -z "$snrd" ] && snrd=0
- [ -z "$snru" ] && snru=0
-
- latnd=$(dbt $latnd)
- latnu=$(dbt $latnu)
- snrd=$(dbt $snrd)
- snru=$(dbt $snru)
-
- if [ "$action" = "lucistat" ]; then
- echo "dsl.line_attenuation_down=$latnd"
- echo "dsl.line_attenuation_up=$latnu"
- echo "dsl.noise_margin_down=$snrd"
- echo "dsl.noise_margin_up=$snru"
- else
- echo "Line Attenuation: ${latnd}dB / ${latnu}dB"
- echo "Noise Margin: ${snrd}dB / ${snru}dB"
- fi
-}
-
-#
-# Is the line up? Or what state is it in?
-#
-line_state() {
- local lsg=$(dsl_cmd lsg)
- local ls=$(dsl_val "$lsg" nLineState);
- local s;
-
- case "$ls" in
- "0x0") s="not initialized" ;;
- "0x1") s="exception" ;;
- "0x10") s="not updated" ;;
- "0xff") s="idle request" ;;
- "0x100") s="idle" ;;
- "0x1ff") s="silent request" ;;
- "0x200") s="silent" ;;
- "0x300") s="handshake" ;;
- "0x380") s="full_init" ;;
- "0x400") s="discovery" ;;
- "0x500") s="training" ;;
- "0x600") s="analysis" ;;
- "0x700") s="exchange" ;;
- "0x800") s="showtime_no_sync" ;;
- "0x801") s="showtime_tc_sync" ;;
- "0x900") s="fastretrain" ;;
- "0xa00") s="lowpower_l2" ;;
- "0xb00") s="loopdiagnostic active" ;;
- "0xb10") s="loopdiagnostic data exchange" ;;
- "0xb20") s="loopdiagnostic data request" ;;
- "0xc00") s="loopdiagnostic complete" ;;
- "0x1000000") s="test" ;;
- "0xd00") s="resync" ;;
- "0x3c0") s="short init entry" ;;
- "") s="not running daemon"; ls="0xfff" ;;
- *) s="unknown" ;;
- esac
-
- if [ $action = "lucistat" ]; then
- echo "dsl.line_state_num=$ls"
- echo "dsl.line_state_detail=\"$s\""
- if [ "$ls" = "0x801" ]; then
- echo "dsl.line_state=\"UP\""
- else
- echo "dsl.line_state=\"DOWN\""
- fi
- else
- if [ "$ls" = "0x801" ]; then
- echo "Line State: UP [$ls: $s]"
- else
- echo "Line State: DOWN [$ls: $s]"
- fi
- fi
-}
-
-#
-# Main status routine
-#
-status() {
- chipset
- line_state
- data_rates
- line_data
- line_uptime
-}
-
-#
-# Luci (lua) compatible version that's easy to parse
-#
-lucistat() {
- echo "local dsl={}"
- status
- echo "return dsl"
-}
-
-
-annex_b=10_00_10_00_00_04_00_00
-annex_bdmt=10_00_00_00_00_00_00_00
-annex_b2=00_00_10_00_00_00_00_00
-annex_b2p=00_00_00_00_00_04_00_00
-annex_a=04_01_04_00_00_01_00_00
-annex_at1=01_00_00_00_00_00_00_00
-annex_alite=00_01_00_00_00_00_00_00
-annex_admt=04_00_00_00_00_00_00_00
-annex_a2=00_00_04_00_00_00_00_00
-annex_a2p=00_00_00_00_00_01_00_00
-annex_l=00_00_00_00_04_00_00_00
-annex_m=00_00_00_00_40_00_04_00
-annex_m2=00_00_00_00_40_00_00_00
-annex_m2p=00_00_00_00_00_00_04_00
-
-#
-# Simple start routine
-#
start() {
- local annex
- local firmware
- local xtu
+ local firmware xtu
+
config_load network
- config_get annex wan annex
+
config_get firmware wan firmware
-
- # get xtu
- eval "xtu=\"\${annex_$annex}\""
-
- # check for firmware
[ -z "${firmware}" ] &&
firmware=vdsl.bin
- # start CPE dsl daemon in the background
- service_start /sbin/vdsl_cpe_control -i${xtu} \
- -n /sbin/dsl_notify.sh \
- -f /lib/firmware/${firmware}
+ config_get xtu wan xtu
+ [ -z "${xtu}" ] &&
+ xtu=10_00_10_00_00_04_01_07
+
+ service_start /sbin/vdsl_cpe_control \
+ -i${xtu} \
+ -T4_0_1
+ -n /sbin/dsl_notify.sh \
+ -f /lib/firmware/${firmware}
}
-#
-# For stop we want to simulate the notification call for when
-# the line goes down, so that we can stop the ppp link before
-# we die.
-#
stop() {
DSL_NOTIFICATION_TYPE="DSL_INTERFACE_STATUS" \
DSL_INTERFACE_STATUS="DOWN" \
service_stop /sbin/vdsl_cpe_control
}
-
+++ /dev/null
-#!/bin/sh
-#
-# This script is called by dsl_cpe_control whenever there is a DSL event,
-# we only actually care about the DSL_INTERFACE_STATUS events as these
-# tell us the line has either come up or gone down.
-#
-# The rest of the code is basically the same at the atm hotplug code
-#
-
-[ "$DSL_NOTIFICATION_TYPE" = "DSL_INTERFACE_STATUS" ] || exit 0
-
-. /usr/share/libubox/jshn.sh
-. /lib/functions.sh
-. /lib/functions/leds.sh
-
-include /lib/network
-scan_interfaces
-
-logger "Found no matching interface for DSL notification ($DSL_INTERFACE_STATUS)"
-
-local default
-config_load system
-config_get default led_adsl default
-if [ "$default" != 1 ]; then
- case "$DSL_INTERFACE_STATUS" in
- "HANDSHAKE") led_timer adsl 500 500;;
- "TRAINING") led_timer adsl 200 200;;
- "UP") led_on adsl;;
- *) led_off adsl
- esac
-fi
-
-local interfaces=`ubus list network.interface.\* | cut -d"." -f3`
-local ifc
-for ifc in $interfaces; do
-
- local up
- json_load "$(ifstatus $ifc)"
- json_get_var up up
-
- local auto
- config_get_bool auto "$ifc" auto 1
-
- local proto
- json_get_var proto proto
-
- if [ "$DSL_INTERFACE_STATUS" = "UP" ]; then
- if [ "$proto" = "pppoa" ] && [ "$up" != 1 ] && [ "$auto" = 1 ]; then
- ( sleep 1; ifup "$ifc" ) &
- fi
- else
- if [ "$proto" = "pppoa" ] && [ "$up" = 1 ] && [ "$auto" = 1 ]; then
- ( sleep 1; ifdown "$ifc" ) &
- else
- json_get_var autostart autostart
- if [ "$proto" = "pppoa" ] && [ "$up" != 1 ] && [ "$autostart" = 1 ]; then
- ( sleep 1; ifdown "$ifc" ) &
- fi
- fi
- fi
-done
-
-
--- /dev/null
+#!/bin/sh /etc/rc.common
+# Copyright (C) 2012 OpenWrt.org
+
+XDSL_CTRL=dsl_cpe_control
+
+#
+# Basic functions to send CLI commands to the vdsl_cpe_control daemon
+#
+dsl_cmd() {
+ killall -0 ${XDSL_CTRL} && (
+ echo "$@" > /tmp/pipe/dsl_cpe0_cmd
+ cat /tmp/pipe/dsl_cpe0_ack
+ )
+}
+dsl_val() {
+ echo $(expr "$1" : '.*'$2'=\([-\.[:alnum:]]*\).*')
+}
+
+#
+# Simple divide by 10 routine to cope with one decimal place
+#
+dbt() {
+ local a=$(expr $1 / 10)
+ local b=$(expr $1 % 10)
+ echo "${a}.${b}"
+}
+#
+# Take a number and convert to k or meg
+#
+scale() {
+ local val=$1
+ local a
+ local b
+
+ if [ "$val" -gt 1000000 ]; then
+ a=$(expr $val / 1000)
+ b=$(expr $a % 1000)
+ a=$(expr $a / 1000)
+ printf "%d.%03d Mb" ${a} ${b}
+ elif [ "$val" -gt 1000 ]; then
+ a=$(expr $val / 1000)
+ printf "%d Kb" ${a}
+ else
+ echo "${val} b"
+ fi
+}
+
+#
+# Read the data rates for both directions
+#
+data_rates() {
+ local csg
+ local dru
+ local drd
+ local sdru
+ local sdrd
+
+ csg=$(dsl_cmd g997csg 0 1)
+ drd=$(dsl_val "$csg" ActualDataRate)
+
+ csg=$(dsl_cmd g997csg 0 0)
+ dru=$(dsl_val "$csg" ActualDataRate)
+
+ [ -z "$drd" ] && drd=0
+ [ -z "$dru" ] && dru=0
+
+ sdrd=$(scale $drd)
+ sdru=$(scale $dru)
+
+ if [ "$action" = "lucistat" ]; then
+ echo "dsl.data_rate_down=$drd"
+ echo "dsl.data_rate_up=$dru"
+ echo "dsl.data_rate_down_s=\"$sdrd\""
+ echo "dsl.data_rate_up_s=\"$sdru\""
+ else
+ echo "Data Rate: ${sdrd}/s / ${sdru}/s"
+ fi
+}
+
+#
+# Chipset
+#
+chipset() {
+ local vig
+ local cs
+ local csv
+
+ vig=$(dsl_cmd vig)
+ cs=$(dsl_val "$vig" DSL_ChipSetType)
+ csv=$(dsl_val "$vig" DSL_ChipSetHWVersion)
+
+ if [ "$action" = "lucistat" ]; then
+ echo "dsl.chipset=\"${cs} ${csv}\""
+ else
+ echo "Chipset: ${cs} ${csv}"
+ fi
+}
+
+#
+# Work out how long the line has been up
+#
+line_uptime() {
+ local ccsg
+ local et
+ local etr
+ local d
+ local h
+ local m
+ local s
+ local rc=""
+
+ ccsg=$(dsl_cmd pmccsg 0 0 0)
+ et=$(dsl_val "$ccsg" nElapsedTime)
+
+ [ -z "$et" ] && et=0
+
+ if [ "$action" = "lucistat" ]; then
+ echo "dsl.line_uptime=${et}"
+ return
+ fi
+
+ d=$(expr $et / 86400)
+ etr=$(expr $et % 86400)
+ h=$(expr $etr / 3600)
+ etr=$(expr $etr % 3600)
+ m=$(expr $etr / 60)
+ s=$(expr $etr % 60)
+
+
+ [ "${d}${h}${m}${s}" -ne 0 ] && rc="${s}s"
+ [ "${d}${h}${m}" -ne 0 ] && rc="${m}m ${rc}"
+ [ "${d}${h}" -ne 0 ] && rc="${h}h ${rc}"
+ [ "${d}" -ne 0 ] && rc="${d}d ${rc}"
+
+ [ -z "$rc" ] && rc="down"
+ echo "Line Uptime: ${rc}"
+}
+
+#
+# Get noise and attenuation figures
+#
+line_data() {
+ local lsg
+ local latnu
+ local latnd
+ local snru
+ local snrd
+
+ lsg=$(dsl_cmd g997lsg 1 1)
+ latnd=$(dsl_val "$lsg" LATN)
+ snrd=$(dsl_val "$lsg" SNR)
+
+ lsg=$(dsl_cmd g997lsg 0 1)
+ latnu=$(dsl_val "$lsg" LATN)
+ snru=$(dsl_val "$lsg" SNR)
+
+ [ -z "$latnd" ] && latnd=0
+ [ -z "$latnu" ] && latnu=0
+ [ -z "$snrd" ] && snrd=0
+ [ -z "$snru" ] && snru=0
+
+ latnd=$(dbt $latnd)
+ latnu=$(dbt $latnu)
+ snrd=$(dbt $snrd)
+ snru=$(dbt $snru)
+
+ if [ "$action" = "lucistat" ]; then
+ echo "dsl.line_attenuation_down=$latnd"
+ echo "dsl.line_attenuation_up=$latnu"
+ echo "dsl.noise_margin_down=$snrd"
+ echo "dsl.noise_margin_up=$snru"
+ else
+ echo "Line Attenuation: ${latnd}dB / ${latnu}dB"
+ echo "Noise Margin: ${snrd}dB / ${snru}dB"
+ fi
+}
+
+#
+# Is the line up? Or what state is it in?
+#
+line_state() {
+ local lsg=$(dsl_cmd lsg)
+ local ls=$(dsl_val "$lsg" nLineState);
+ local s;
+
+ case "$ls" in
+ "0x0") s="not initialized" ;;
+ "0x1") s="exception" ;;
+ "0x10") s="not updated" ;;
+ "0xff") s="idle request" ;;
+ "0x100") s="idle" ;;
+ "0x1ff") s="silent request" ;;
+ "0x200") s="silent" ;;
+ "0x300") s="handshake" ;;
+ "0x380") s="full_init" ;;
+ "0x400") s="discovery" ;;
+ "0x500") s="training" ;;
+ "0x600") s="analysis" ;;
+ "0x700") s="exchange" ;;
+ "0x800") s="showtime_no_sync" ;;
+ "0x801") s="showtime_tc_sync" ;;
+ "0x900") s="fastretrain" ;;
+ "0xa00") s="lowpower_l2" ;;
+ "0xb00") s="loopdiagnostic active" ;;
+ "0xb10") s="loopdiagnostic data exchange" ;;
+ "0xb20") s="loopdiagnostic data request" ;;
+ "0xc00") s="loopdiagnostic complete" ;;
+ "0x1000000") s="test" ;;
+ "0xd00") s="resync" ;;
+ "0x3c0") s="short init entry" ;;
+ "") s="not running daemon"; ls="0xfff" ;;
+ *) s="unknown" ;;
+ esac
+
+ if [ $action = "lucistat" ]; then
+ echo "dsl.line_state_num=$ls"
+ echo "dsl.line_state_detail=\"$s\""
+ if [ "$ls" = "0x801" ]; then
+ echo "dsl.line_state=\"UP\""
+ else
+ echo "dsl.line_state=\"DOWN\""
+ fi
+ else
+ if [ "$ls" = "0x801" ]; then
+ echo "Line State: UP [$ls: $s]"
+ else
+ echo "Line State: DOWN [$ls: $s]"
+ fi
+ fi
+}
+
+status() {
+ chipset
+ line_state
+ data_rates
+ line_data
+ line_uptime
+}
+
+lucistat() {
+ echo "local dsl={}"
+ status
+ echo "return dsl"
+}
--- /dev/null
+#!/bin/sh
+#
+# This script is called by dsl_cpe_control whenever there is a DSL event,
+# we only actually care about the DSL_INTERFACE_STATUS events as these
+# tell us the line has either come up or gone down.
+#
+# The rest of the code is basically the same at the atm hotplug code
+#
+
+[ "$DSL_NOTIFICATION_TYPE" = "DSL_INTERFACE_STATUS" ] || exit 0
+
+. /usr/share/libubox/jshn.sh
+. /lib/functions.sh
+. /lib/functions/leds.sh
+
+include /lib/network
+scan_interfaces
+
+local default
+config_load system
+config_get default led_adsl default
+if [ "$default" != 1 ]; then
+ case "$DSL_INTERFACE_STATUS" in
+ "HANDSHAKE") led_timer adsl 500 500;;
+ "TRAINING") led_timer adsl 200 200;;
+ "UP") led_on adsl;;
+ *) led_off adsl
+ esac
+fi
+
+local interfaces=`ubus list network.interface.\* | cut -d"." -f3`
+local ifc
+for ifc in $interfaces; do
+
+ local up
+ json_load "$(ifstatus $ifc)"
+ json_get_var up up
+
+ local auto
+ config_get_bool auto "$ifc" auto 1
+
+ local proto
+ json_get_var proto proto
+
+ if [ "$DSL_INTERFACE_STATUS" = "UP" ]; then
+ if [ "$proto" = "pppoa" ] && [ "$up" != 1 ] && [ "$auto" = 1 ]; then
+ ( sleep 1; ifup "$ifc" ) &
+ fi
+ else
+ if [ "$proto" = "pppoa" ] && [ "$up" = 1 ] && [ "$auto" = 1 ]; then
+ ( sleep 1; ifdown "$ifc" ) &
+ else
+ json_get_var autostart autostart
+ if [ "$proto" = "pppoa" ] && [ "$up" != 1 ] && [ "$autostart" = 1 ]; then
+ ( sleep 1; ifdown "$ifc" ) &
+ fi
+ fi
+ fi
+done
+
+
projects / openwrt / openwrt.git / commitdiff