Add support for new LOM devices on the latest generation ICHx platforms.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
#define NWAY_LPAR_ASM_DIR 0x0800 /* LP Asymmetric Pause Direction bit */
/* Autoneg Expansion Register */
+#define NWAY_ER_LP_NWAY_CAPS 0x0001 /* LP has Auto Neg Capability */
/* 1000BASE-T Control Register */
#define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */
#define E1000_EECD_DO 0x00000008 /* NVM Data Out */
#define E1000_EECD_REQ 0x00000040 /* NVM Access Request */
#define E1000_EECD_GNT 0x00000080 /* NVM Access Grant */
+#define E1000_EECD_PRES 0x00000100 /* NVM Present */
#define E1000_EECD_SIZE 0x00000200 /* NVM Size (0=64 word 1=256 word) */
/* NVM Addressing bits based on type (0-small, 1-large) */
#define E1000_EECD_ADDR_BITS 0x00000400
board_80003es2lan,
board_ich8lan,
board_ich9lan,
+ board_ich10lan,
};
struct e1000_queue_stats {
extern struct e1000_info e1000_82573_info;
extern struct e1000_info e1000_ich8_info;
extern struct e1000_info e1000_ich9_info;
+extern struct e1000_info e1000_ich10_info;
extern struct e1000_info e1000_es2_info;
extern s32 e1000e_read_pba_num(struct e1000_hw *hw, u32 *pba_num);
extern s32 e1000e_get_phy_info_m88(struct e1000_hw *hw);
extern s32 e1000e_read_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 *data);
extern s32 e1000e_write_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 data);
+extern s32 e1000e_phy_init_script_igp3(struct e1000_hw *hw);
extern enum e1000_phy_type e1000e_get_phy_type_from_id(u32 phy_id);
extern s32 e1000e_determine_phy_address(struct e1000_hw *hw);
extern s32 e1000e_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data);
case e1000_82573:
case e1000_ich8lan:
case e1000_ich9lan:
+ case e1000_ich10lan:
toggle = 0x7FFFF033;
break;
default:
REG_PATTERN_TEST(E1000_TIDV, 0x0000FFFF, 0x0000FFFF);
for (i = 0; i < mac->rar_entry_count; i++)
REG_PATTERN_TEST_ARRAY(E1000_RA, ((i << 1) + 1),
- 0x8003FFFF, 0xFFFFFFFF);
+ ((mac->type == e1000_ich10lan) ?
+ 0x8007FFFF : 0x8003FFFF),
+ 0xFFFFFFFF);
for (i = 0; i < mac->mta_reg_count; i++)
REG_PATTERN_TEST_ARRAY(E1000_MTA, i, 0xFFFFFFFF, 0xFFFFFFFF);
/* Test each interrupt */
for (i = 0; i < 10; i++) {
- if ((adapter->flags & FLAG_IS_ICH) && (i == 8))
- continue;
-
/* Interrupt to test */
mask = 1 << i;
+ if (adapter->flags & FLAG_IS_ICH) {
+ switch (mask) {
+ case E1000_ICR_RXSEQ:
+ continue;
+ case 0x00000100:
+ if (adapter->hw.mac.type == e1000_ich8lan ||
+ adapter->hw.mac.type == e1000_ich9lan)
+ continue;
+ break;
+ default:
+ break;
+ }
+ }
+
if (!shared_int) {
/*
* Disable the interrupt to be reported in
#define E1000_DEV_ID_ICH10_R_BM_LM 0x10CC
#define E1000_DEV_ID_ICH10_R_BM_LF 0x10CD
#define E1000_DEV_ID_ICH10_R_BM_V 0x10CE
+#define E1000_DEV_ID_ICH10_D_BM_LM 0x10DE
+#define E1000_DEV_ID_ICH10_D_BM_LF 0x10DF
#define E1000_FUNC_1 1
e1000_80003es2lan,
e1000_ich8lan,
e1000_ich9lan,
+ e1000_ich10lan,
};
enum e1000_media_type {
* 82567LM-2 Gigabit Network Connection
* 82567LF-2 Gigabit Network Connection
* 82567V-2 Gigabit Network Connection
- * 82562GT-3 10/100 Network Connection
+ * 82567LF-3 Gigabit Network Connection
+ * 82567LM-3 Gigabit Network Connection
* 82567LM-4 Gigabit Network Connection
*/
static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank);
static s32 e1000_retry_write_flash_byte_ich8lan(struct e1000_hw *hw,
u32 offset, u8 byte);
+static s32 e1000_read_flash_byte_ich8lan(struct e1000_hw *hw, u32 offset,
+ u8 *data);
static s32 e1000_read_flash_word_ich8lan(struct e1000_hw *hw, u32 offset,
u16 *data);
static s32 e1000_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset,
u8 size, u16 *data);
static s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw);
static s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw);
+static s32 e1000_get_cfg_done_ich8lan(struct e1000_hw *hw);
static inline u16 __er16flash(struct e1000_hw *hw, unsigned long reg)
{
return 0;
}
+/**
+ * e1000_valid_nvm_bank_detect_ich8lan - finds out the valid bank 0 or 1
+ * @hw: pointer to the HW structure
+ * @bank: pointer to the variable that returns the active bank
+ *
+ * Reads signature byte from the NVM using the flash access registers.
+ **/
+static s32 e1000_valid_nvm_bank_detect_ich8lan(struct e1000_hw *hw, u32 *bank)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ /* flash bank size is in words */
+ u32 bank1_offset = nvm->flash_bank_size * sizeof(u16);
+ u32 act_offset = E1000_ICH_NVM_SIG_WORD * 2 + 1;
+ u8 bank_high_byte = 0;
+
+ if (hw->mac.type != e1000_ich10lan) {
+ if (er32(EECD) & E1000_EECD_SEC1VAL)
+ *bank = 1;
+ else
+ *bank = 0;
+ } else {
+ /*
+ * Make sure the signature for bank 0 is valid,
+ * if not check for bank1
+ */
+ e1000_read_flash_byte_ich8lan(hw, act_offset, &bank_high_byte);
+ if ((bank_high_byte & 0xC0) == 0x80) {
+ *bank = 0;
+ } else {
+ /*
+ * find if segment 1 is valid by verifying
+ * bit 15:14 = 10b in word 0x13
+ */
+ e1000_read_flash_byte_ich8lan(hw,
+ act_offset + bank1_offset,
+ &bank_high_byte);
+
+ /* bank1 has a valid signature equivalent to SEC1V */
+ if ((bank_high_byte & 0xC0) == 0x80) {
+ *bank = 1;
+ } else {
+ hw_dbg(hw, "ERROR: EEPROM not present\n");
+ return -E1000_ERR_NVM;
+ }
+ }
+ }
+
+ return 0;
+}
+
/**
* e1000_read_nvm_ich8lan - Read word(s) from the NVM
* @hw: pointer to the HW structure
struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
u32 act_offset;
s32 ret_val;
+ u32 bank = 0;
u16 i, word;
if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) ||
if (ret_val)
return ret_val;
- /* Start with the bank offset, then add the relative offset. */
- act_offset = (er32(EECD) & E1000_EECD_SEC1VAL)
- ? nvm->flash_bank_size
- : 0;
+ ret_val = e1000_valid_nvm_bank_detect_ich8lan(hw, &bank);
+ if (ret_val)
+ return ret_val;
+
+ act_offset = (bank) ? nvm->flash_bank_size : 0;
act_offset += offset;
for (i = 0; i < words; i++) {
return e1000_read_flash_data_ich8lan(hw, offset, 2, data);
}
+/**
+ * e1000_read_flash_byte_ich8lan - Read byte from flash
+ * @hw: pointer to the HW structure
+ * @offset: The offset of the byte to read.
+ * @data: Pointer to a byte to store the value read.
+ *
+ * Reads a single byte from the NVM using the flash access registers.
+ **/
+static s32 e1000_read_flash_byte_ich8lan(struct e1000_hw *hw, u32 offset,
+ u8 *data)
+{
+ s32 ret_val;
+ u16 word = 0;
+
+ ret_val = e1000_read_flash_data_ich8lan(hw, offset, 1, &word);
+ if (ret_val)
+ return ret_val;
+
+ *data = (u8)word;
+
+ return 0;
+}
+
/**
* e1000_read_flash_data_ich8lan - Read byte or word from NVM
* @hw: pointer to the HW structure
{
struct e1000_nvm_info *nvm = &hw->nvm;
struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
- u32 i, act_offset, new_bank_offset, old_bank_offset;
+ u32 i, act_offset, new_bank_offset, old_bank_offset, bank;
s32 ret_val;
u16 data;
* write to bank 0 etc. We also need to erase the segment that
* is going to be written
*/
- if (!(er32(EECD) & E1000_EECD_SEC1VAL)) {
+ ret_val = e1000_valid_nvm_bank_detect_ich8lan(hw, &bank);
+ if (ret_val)
+ return ret_val;
+
+ if (bank == 0) {
new_bank_offset = nvm->flash_bank_size;
old_bank_offset = 0;
e1000_erase_flash_bank_ich8lan(hw, 1);
* 'LPLU Enabled' and 'Gig Disable' to force link speed negotiation
* to a lower speed.
*
- * Should only be called for ICH9 devices.
+ * Should only be called for ICH9 and ICH10 devices.
**/
void e1000e_disable_gig_wol_ich8lan(struct e1000_hw *hw)
{
u32 phy_ctrl;
- if (hw->mac.type == e1000_ich9lan) {
+ if ((hw->mac.type == e1000_ich10lan) ||
+ (hw->mac.type == e1000_ich9lan)) {
phy_ctrl = er32(PHY_CTRL);
phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU |
E1000_PHY_CTRL_GBE_DISABLE;
return 0;
}
+/**
+ * e1000_get_cfg_done_ich8lan - Read config done bit
+ * @hw: pointer to the HW structure
+ *
+ * Read the management control register for the config done bit for
+ * completion status. NOTE: silicon which is EEPROM-less will fail trying
+ * to read the config done bit, so an error is *ONLY* logged and returns
+ * E1000_SUCCESS. If we were to return with error, EEPROM-less silicon
+ * would not be able to be reset or change link.
+ **/
+static s32 e1000_get_cfg_done_ich8lan(struct e1000_hw *hw)
+{
+ u32 bank = 0;
+
+ e1000e_get_cfg_done(hw);
+
+ /* If EEPROM is not marked present, init the IGP 3 PHY manually */
+ if (hw->mac.type != e1000_ich10lan) {
+ if (((er32(EECD) & E1000_EECD_PRES) == 0) &&
+ (hw->phy.type == e1000_phy_igp_3)) {
+ e1000e_phy_init_script_igp3(hw);
+ }
+ } else {
+ if (e1000_valid_nvm_bank_detect_ich8lan(hw, &bank)) {
+ /* Maybe we should do a basic PHY config */
+ hw_dbg(hw, "EEPROM not present\n");
+ return -E1000_ERR_CONFIG;
+ }
+ }
+
+ return 0;
+}
+
/**
* e1000_clear_hw_cntrs_ich8lan - Clear statistical counters
* @hw: pointer to the HW structure
.check_reset_block = e1000_check_reset_block_ich8lan,
.commit_phy = NULL,
.force_speed_duplex = e1000_phy_force_speed_duplex_ich8lan,
- .get_cfg_done = e1000e_get_cfg_done,
+ .get_cfg_done = e1000_get_cfg_done_ich8lan,
.get_cable_length = e1000e_get_cable_length_igp_2,
.get_phy_info = e1000_get_phy_info_ich8lan,
.read_phy_reg = e1000e_read_phy_reg_igp,
.nvm_ops = &ich8_nvm_ops,
};
+struct e1000_info e1000_ich10_info = {
+ .mac = e1000_ich10lan,
+ .flags = FLAG_HAS_JUMBO_FRAMES
+ | FLAG_IS_ICH
+ | FLAG_HAS_WOL
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_CTRLEXT_ON_LOAD
+ | FLAG_HAS_AMT
+ | FLAG_HAS_ERT
+ | FLAG_HAS_FLASH
+ | FLAG_APME_IN_WUC,
+ .pba = 10,
+ .get_variants = e1000_get_variants_ich8lan,
+ .mac_ops = &ich8_mac_ops,
+ .phy_ops = &ich8_phy_ops,
+ .nvm_ops = &ich8_nvm_ops,
+};
[board_80003es2lan] = &e1000_es2_info,
[board_ich8lan] = &e1000_ich8_info,
[board_ich9lan] = &e1000_ich9_info,
+ [board_ich10lan] = &e1000_ich10_info,
};
#ifdef DEBUG
&adapter->link_speed,
&adapter->link_duplex);
e1000_print_link_info(adapter);
+ /*
+ * On supported PHYs, check for duplex mismatch only
+ * if link has autonegotiated at 10/100 half
+ */
+ if ((hw->phy.type == e1000_phy_igp_3 ||
+ hw->phy.type == e1000_phy_bm) &&
+ (hw->mac.autoneg == true) &&
+ (adapter->link_speed == SPEED_10 ||
+ adapter->link_speed == SPEED_100) &&
+ (adapter->link_duplex == HALF_DUPLEX)) {
+ u16 autoneg_exp;
+
+ e1e_rphy(hw, PHY_AUTONEG_EXP, &autoneg_exp);
+
+ if (!(autoneg_exp & NWAY_ER_LP_NWAY_CAPS))
+ e_info("Autonegotiated half duplex but"
+ " link partner cannot autoneg. "
+ " Try forcing full duplex if "
+ "link gets many collisions.\n");
+ }
+
/*
* tweak tx_queue_len according to speed/duplex
* and adjust the timeout factor
{ PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_LF), board_ich9lan },
{ PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_V), board_ich9lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_LM), board_ich10lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_LF), board_ich10lan },
+
{ } /* terminate list */
};
MODULE_DEVICE_TABLE(pci, e1000_pci_tbl);
return 0;
}
+/**
+ * e1000e_phy_init_script_igp3 - Inits the IGP3 PHY
+ * @hw: pointer to the HW structure
+ *
+ * Initializes a Intel Gigabit PHY3 when an EEPROM is not present.
+ **/
+s32 e1000e_phy_init_script_igp3(struct e1000_hw *hw)
+{
+ hw_dbg(hw, "Running IGP 3 PHY init script\n");
+
+ /* PHY init IGP 3 */
+ /* Enable rise/fall, 10-mode work in class-A */
+ e1e_wphy(hw, 0x2F5B, 0x9018);
+ /* Remove all caps from Replica path filter */
+ e1e_wphy(hw, 0x2F52, 0x0000);
+ /* Bias trimming for ADC, AFE and Driver (Default) */
+ e1e_wphy(hw, 0x2FB1, 0x8B24);
+ /* Increase Hybrid poly bias */
+ e1e_wphy(hw, 0x2FB2, 0xF8F0);
+ /* Add 4% to Tx amplitude in Gig mode */
+ e1e_wphy(hw, 0x2010, 0x10B0);
+ /* Disable trimming (TTT) */
+ e1e_wphy(hw, 0x2011, 0x0000);
+ /* Poly DC correction to 94.6% + 2% for all channels */
+ e1e_wphy(hw, 0x20DD, 0x249A);
+ /* ABS DC correction to 95.9% */
+ e1e_wphy(hw, 0x20DE, 0x00D3);
+ /* BG temp curve trim */
+ e1e_wphy(hw, 0x28B4, 0x04CE);
+ /* Increasing ADC OPAMP stage 1 currents to max */
+ e1e_wphy(hw, 0x2F70, 0x29E4);
+ /* Force 1000 ( required for enabling PHY regs configuration) */
+ e1e_wphy(hw, 0x0000, 0x0140);
+ /* Set upd_freq to 6 */
+ e1e_wphy(hw, 0x1F30, 0x1606);
+ /* Disable NPDFE */
+ e1e_wphy(hw, 0x1F31, 0xB814);
+ /* Disable adaptive fixed FFE (Default) */
+ e1e_wphy(hw, 0x1F35, 0x002A);
+ /* Enable FFE hysteresis */
+ e1e_wphy(hw, 0x1F3E, 0x0067);
+ /* Fixed FFE for short cable lengths */
+ e1e_wphy(hw, 0x1F54, 0x0065);
+ /* Fixed FFE for medium cable lengths */
+ e1e_wphy(hw, 0x1F55, 0x002A);
+ /* Fixed FFE for long cable lengths */
+ e1e_wphy(hw, 0x1F56, 0x002A);
+ /* Enable Adaptive Clip Threshold */
+ e1e_wphy(hw, 0x1F72, 0x3FB0);
+ /* AHT reset limit to 1 */
+ e1e_wphy(hw, 0x1F76, 0xC0FF);
+ /* Set AHT master delay to 127 msec */
+ e1e_wphy(hw, 0x1F77, 0x1DEC);
+ /* Set scan bits for AHT */
+ e1e_wphy(hw, 0x1F78, 0xF9EF);
+ /* Set AHT Preset bits */
+ e1e_wphy(hw, 0x1F79, 0x0210);
+ /* Change integ_factor of channel A to 3 */
+ e1e_wphy(hw, 0x1895, 0x0003);
+ /* Change prop_factor of channels BCD to 8 */
+ e1e_wphy(hw, 0x1796, 0x0008);
+ /* Change cg_icount + enable integbp for channels BCD */
+ e1e_wphy(hw, 0x1798, 0xD008);
+ /*
+ * Change cg_icount + enable integbp + change prop_factor_master
+ * to 8 for channel A
+ */
+ e1e_wphy(hw, 0x1898, 0xD918);
+ /* Disable AHT in Slave mode on channel A */
+ e1e_wphy(hw, 0x187A, 0x0800);
+ /*
+ * Enable LPLU and disable AN to 1000 in non-D0a states,
+ * Enable SPD+B2B
+ */
+ e1e_wphy(hw, 0x0019, 0x008D);
+ /* Enable restart AN on an1000_dis change */
+ e1e_wphy(hw, 0x001B, 0x2080);
+ /* Enable wh_fifo read clock in 10/100 modes */
+ e1e_wphy(hw, 0x0014, 0x0045);
+ /* Restart AN, Speed selection is 1000 */
+ e1e_wphy(hw, 0x0000, 0x1340);
+
+ return 0;
+}
+
/* Internal function pointers */
/**