--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca955x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Huawei AP5030DN";
+ compatible = "huawei,ap5030dn", "qca,qca9550", "qca,qca9558";
+
+ chosen {
+ bootargs = "console=ttyS0,9600n8";
+ };
+
+ aliases {
+ led-boot = &led_function_red;
+ led-failsafe = &led_function_red;
+ led-running = &led_function_green;
+ led-upgrade = &led_function_red;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_function_green: led-status-red {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio 18 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_function_red: led-status-green {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
+ };
+
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ restart {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+
+ watchdog {
+ pinctrl-names = "default";
+ pinctrl-0 = <&wdt_gpio15>;
+
+ compatible = "linux,wdt-gpio";
+ gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
+ hw_algo = "toggle";
+ hw_margin_ms = <100>;
+ always-running;
+ };
+
+ virtual_flash {
+ compatible = "mtd-concat";
+ devices = <&fwconcat0 &fwconcat1>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "firmware";
+ reg = <0x0 0x1e00000>;
+ compatible = "openwrt,uimage", "denx,uimage";
+ };
+ };
+ };
+};
+
+&spi {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot-a";
+ reg = <0x0 0x80000>;
+ read-only;
+ };
+
+ // The BootupA/B partitions store the addresses
+ // of the main and backup kernel in flash (which is the same here).
+ // During sysupgrade, these addresses are set to the start of the
+ // "firmware" partition.
+ partition@80000 {
+ label = "BootupA";
+ reg = <0x80000 0x20000>;
+ };
+
+ partition@a0000 {
+ label = "BootupB";
+ reg = <0xa0000 0x20000>;
+ };
+
+ partition@c0000 {
+ label = "u-boot-env";
+ reg = <0xc0000 0x20000>;
+ read-only;
+ };
+
+ partition@e0000 {
+ label = "BoardData";
+ reg = <0xe0000 0x20000>;
+ read-only;
+ };
+
+ // In the vendor layout, there are the "SysImageA" (12 MiB)
+ // and the "ConfigA" (3 MiB) partitions here.
+ fwconcat0: partition@100000 {
+ label = "fwconcat0";
+ reg = <0x100000 0xF00000>;
+ };
+
+ partition@1000000 {
+ label = "u-boot-b";
+ reg = <0x1000000 0x80000>;
+ read-only;
+ };
+
+ partition@1080000 {
+ label = "ResultA";
+ reg = <0x1080000 0x20000>;
+ read-only;
+ };
+
+ partition@10a0000 {
+ label = "ResultB";
+ reg = <0x10a0000 0x20000>;
+ read-only;
+ };
+
+ // In the vendor layout, there are the "SysImageB" (12 MiB)
+ // and the "ConfigB" (3 MiB) partitions here.
+ fwconcat1: partition@10c0000 {
+ label = "fwconcat1";
+ reg = <0x10c0000 0xF00000>;
+ };
+
+ art: partition@1fc0000 {
+ label = "art";
+ reg = <0x1fc0000 0x40000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_art_2005b: macaddr@2005b {
+ compatible = "mac-base";
+ reg = <0x2005b 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ cal_art_1000: cal@1000 {
+ reg = <0x1000 0x440>;
+ };
+
+ cal_art_5000: cal@5000 {
+ reg = <0x5000 0x844>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&wmac {
+ status = "okay";
+
+ nvmem-cells = <&macaddr_art_2005b 3>, <&cal_art_1000>;
+ nvmem-cell-names = "mac-address", "calibration";
+};
+
+&pcie0 {
+ status = "okay";
+
+ wifi@0,0 {
+ compatible = "qcom,ath10k";
+ reg = <0x0000 0 0 0 0>;
+ nvmem-cells = <&macaddr_art_2005b 2>, <&cal_art_5000>;
+ nvmem-cell-names = "mac-address", "calibration";
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ nvmem-cells = <&macaddr_art_2005b 0>;
+ nvmem-cell-names = "mac-address";
+
+ pll-data = <0xa6000000 0xa0000101 0xa0001313>;
+ phy-handle = <&phy0>;
+
+ gmac-config {
+ device = <&gmac>;
+ rxdv-delay = <3>;
+ rxd-delay = <3>;
+ txen-delay = <0>;
+ txd-delay = <0>;
+ };
+};
+
+ð1 {
+ status = "okay";
+
+ nvmem-cells = <&macaddr_art_2005b 1>;
+ nvmem-cell-names = "mac-address";
+
+ pll-data = <0x03000101 0x00000101 0x00001313>;
+ phy-handle = <&phy1>;
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy0: ethernet-phy@18 {
+ reg = <0x18>;
+ };
+};
+
+&mdio1 {
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&pinmux {
+ wdt_gpio15: pinmux_wdt_gpio15 {
+ pinctrl-single,bits = <0xc 0x0 0xFF000000>;
+ };
+};
+
+&wdt {
+ status = "disabled";
+};
static inline void mr18_init(void) { }
#endif
+#ifdef CONFIG_BOARD_HUAWEI_AP5030DN
+static inline void ap5030dn_init(void)
+{
+ const unsigned int ap5030dn_watchdog_gpio = 15;
+ unsigned int gpiobase, reg;
+
+ gpiobase = KSEG1ADDR(AR71XX_GPIO_BASE);
+
+ printf("Huawei AP5030DN\n");
+
+ reg = READREG(gpiobase + AR71XX_GPIO_REG_OE);
+ WRITEREG(gpiobase + AR71XX_GPIO_REG_OE,
+ reg & ~(1 << ap5030dn_watchdog_gpio));
+
+ /* Set GPIO15 MUX to output CLK_OBS5 (= CPU_CLK/4)
+ * to keep the watchdog happy until wdt-gpio takes over
+ */
+ reg = READREG(gpiobase + AR934X_GPIO_REG_OUT_FUNC3);
+ WRITEREG(gpiobase + AR934X_GPIO_REG_OUT_FUNC3,
+ reg | (QCA955X_GPIO_OUTSEL_CLK_OBS5 << 24));
+}
+#else
+static inline void ap5030dn_init(void) { }
+#endif
+
void board_init(void)
{
tlwr1043nd_init();
mr18_init();
+ ap5030dn_init();
}
--- /dev/null
+From 380b50ae3a04222334a3779b3787eba844b1177f Mon Sep 17 00:00:00 2001
+From: Marco von Rosenberg <marcovr@selfnet.de>
+Date: Thu, 16 Nov 2023 20:32:31 +0100
+Subject: net: phy: broadcom: Wire suspend/resume for BCM54612E
+
+The BCM54612E ethernet PHY supports IDDQ-SR.
+Therefore wire-up the suspend and resume callbacks
+to point to bcm54xx_suspend() and bcm54xx_resume().
+
+Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
+Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
+Signed-off-by: David S. Miller <davem@davemloft.net>
+---
+ drivers/net/phy/broadcom.c | 2 ++
+ 1 file changed, 2 insertions(+)
+
+--- a/drivers/net/phy/broadcom.c
++++ b/drivers/net/phy/broadcom.c
+@@ -795,6 +795,8 @@ static struct phy_driver broadcom_driver
+ .config_init = bcm54xx_config_init,
+ .config_intr = bcm_phy_config_intr,
+ .handle_interrupt = bcm_phy_handle_interrupt,
++ .suspend = genphy_suspend,
++ .resume = bcm54xx_resume,
+ }, {
+ .phy_id = PHY_ID_BCM54616S,
+ .phy_id_mask = 0xfffffff0,
projects / openwrt / staging / jow.git / commitdiff