--- /dev/null
+/*
+ * Copyright (c) 2005-2008 Chelsio, Inc. All rights reserved.
+ *
+ * This software is available to you under a choice of one of two
+ * licenses. You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the
+ * OpenIB.org BSD license below:
+ *
+ * Redistribution and use in source and binary forms, with or
+ * without modification, are permitted provided that the following
+ * conditions are met:
+ *
+ * - Redistributions of source code must retain the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer.
+ *
+ * - Redistributions in binary form must reproduce the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer in the documentation and/or other materials
+ * provided with the distribution.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
+ * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
+ * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+ * SOFTWARE.
+ */
+
+#include "common.h"
+#include "regs.h"
+
+enum {
+ /* MDIO_DEV_PMA_PMD registers */
+ AQ_LINK_STAT = 0xe800,
+ AQ_IMASK_PMA = 0xf000,
+
+ /* MDIO_DEV_XGXS registers */
+ AQ_XAUI_RX_CFG = 0xc400,
+ AQ_XAUI_TX_CFG = 0xe400,
+
+ /* MDIO_DEV_ANEG registers */
+ AQ_100M_CTRL = 0x0010,
+ AQ_10G_CTRL = 0x0020,
+ AQ_1G_CTRL = 0xc400,
+ AQ_ANEG_STAT = 0xc800,
+
+ /* MDIO_DEV_VEND1 registers */
+ AQ_FW_VERSION = 0x0020,
+ AQ_IFLAG_GLOBAL = 0xfc00,
+ AQ_IMASK_GLOBAL = 0xff00,
+};
+
+#define AQBIT(x) (1 << (x))
+#define IMASK_PMA AQBIT(0x2)
+#define IMASK_GLOBAL AQBIT(0xf)
+#define ADV_1G_FULL AQBIT(0xf)
+#define ADV_1G_HALF AQBIT(0xe)
+#define ADV_10G_FULL AQBIT(0xc)
+#define AQ_RESET (AQBIT(0xe) | AQBIT(0xf))
+#define AQ_LOWPOWER AQBIT(0xb)
+
+static int aq100x_reset(struct cphy *phy, int wait)
+{
+ /*
+ * Ignore the caller specified wait time; always wait for the reset to
+ * complete. Can take up to 3s.
+ */
+ int err = t3_phy_reset(phy, MDIO_MMD_VEND1, 3000);
+
+ if (err)
+ CH_WARN(phy->adapter, "PHY%d: reset failed (0x%x).\n",
+ phy->mdio.prtad, err);
+
+ return err;
+}
+
+static int aq100x_intr_enable(struct cphy *phy)
+{
+ int err = t3_mdio_write(phy, MDIO_MMD_PMAPMD, AQ_IMASK_PMA, IMASK_PMA);
+ if (err)
+ return err;
+
+ err = t3_mdio_write(phy, MDIO_MMD_VEND1, AQ_IMASK_GLOBAL, IMASK_GLOBAL);
+ return err;
+}
+
+static int aq100x_intr_disable(struct cphy *phy)
+{
+ return t3_mdio_write(phy, MDIO_MMD_VEND1, AQ_IMASK_GLOBAL, 0);
+}
+
+static int aq100x_intr_clear(struct cphy *phy)
+{
+ unsigned int v;
+
+ t3_mdio_read(phy, MDIO_MMD_VEND1, AQ_IFLAG_GLOBAL, &v);
+ t3_mdio_read(phy, MDIO_MMD_PMAPMD, MDIO_STAT1, &v);
+
+ return 0;
+}
+
+static int aq100x_intr_handler(struct cphy *phy)
+{
+ int err;
+ unsigned int cause, v;
+
+ err = t3_mdio_read(phy, MDIO_MMD_VEND1, AQ_IFLAG_GLOBAL, &cause);
+ if (err)
+ return err;
+
+ /* Read (and reset) the latching version of the status */
+ t3_mdio_read(phy, MDIO_MMD_PMAPMD, MDIO_STAT1, &v);
+
+ return cphy_cause_link_change;
+}
+
+static int aq100x_power_down(struct cphy *phy, int off)
+{
+ return mdio_set_flag(&phy->mdio, phy->mdio.prtad,
+ MDIO_MMD_PMAPMD, MDIO_CTRL1,
+ MDIO_CTRL1_LPOWER, off);
+}
+
+static int aq100x_autoneg_enable(struct cphy *phy)
+{
+ int err;
+
+ err = aq100x_power_down(phy, 0);
+ if (!err)
+ err = mdio_set_flag(&phy->mdio, phy->mdio.prtad,
+ MDIO_MMD_AN, MDIO_CTRL1,
+ BMCR_ANENABLE | BMCR_ANRESTART, 1);
+
+ return err;
+}
+
+static int aq100x_autoneg_restart(struct cphy *phy)
+{
+ int err;
+
+ err = aq100x_power_down(phy, 0);
+ if (!err)
+ err = mdio_set_flag(&phy->mdio, phy->mdio.prtad,
+ MDIO_MMD_AN, MDIO_CTRL1,
+ BMCR_ANENABLE | BMCR_ANRESTART, 1);
+
+ return err;
+}
+
+static int aq100x_advertise(struct cphy *phy, unsigned int advertise_map)
+{
+ unsigned int adv;
+ int err;
+
+ /* 10G advertisement */
+ adv = 0;
+ if (advertise_map & ADVERTISED_10000baseT_Full)
+ adv |= ADV_10G_FULL;
+ err = t3_mdio_change_bits(phy, MDIO_MMD_AN, AQ_10G_CTRL,
+ ADV_10G_FULL, adv);
+ if (err)
+ return err;
+
+ /* 1G advertisement */
+ adv = 0;
+ if (advertise_map & ADVERTISED_1000baseT_Full)
+ adv |= ADV_1G_FULL;
+ if (advertise_map & ADVERTISED_1000baseT_Half)
+ adv |= ADV_1G_HALF;
+ err = t3_mdio_change_bits(phy, MDIO_MMD_AN, AQ_1G_CTRL,
+ ADV_1G_FULL | ADV_1G_HALF, adv);
+ if (err)
+ return err;
+
+ /* 100M, pause advertisement */
+ adv = 0;
+ if (advertise_map & ADVERTISED_100baseT_Half)
+ adv |= ADVERTISE_100HALF;
+ if (advertise_map & ADVERTISED_100baseT_Full)
+ adv |= ADVERTISE_100FULL;
+ if (advertise_map & ADVERTISED_Pause)
+ adv |= ADVERTISE_PAUSE_CAP;
+ if (advertise_map & ADVERTISED_Asym_Pause)
+ adv |= ADVERTISE_PAUSE_ASYM;
+ err = t3_mdio_change_bits(phy, MDIO_MMD_AN, AQ_100M_CTRL, 0xfe0, adv);
+
+ return err;
+}
+
+static int aq100x_set_loopback(struct cphy *phy, int mmd, int dir, int enable)
+{
+ return mdio_set_flag(&phy->mdio, phy->mdio.prtad,
+ MDIO_MMD_PMAPMD, MDIO_CTRL1,
+ BMCR_LOOPBACK, enable);
+}
+
+static int aq100x_set_speed_duplex(struct cphy *phy, int speed, int duplex)
+{
+ /* no can do */
+ return -1;
+}
+
+static int aq100x_get_link_status(struct cphy *phy, int *link_ok,
+ int *speed, int *duplex, int *fc)
+{
+ int err;
+ unsigned int v;
+
+ if (link_ok) {
+ err = t3_mdio_read(phy, MDIO_MMD_PMAPMD, AQ_LINK_STAT, &v);
+ if (err)
+ return err;
+
+ *link_ok = v & 1;
+ if (!*link_ok)
+ return 0;
+ }
+
+ err = t3_mdio_read(phy, MDIO_MMD_AN, AQ_ANEG_STAT, &v);
+ if (err)
+ return err;
+
+ if (speed) {
+ switch (v & 0x6) {
+ case 0x6:
+ *speed = SPEED_10000;
+ break;
+ case 0x4:
+ *speed = SPEED_1000;
+ break;
+ case 0x2:
+ *speed = SPEED_100;
+ break;
+ case 0x0:
+ *speed = SPEED_10;
+ break;
+ }
+ }
+
+ if (duplex)
+ *duplex = v & 1 ? DUPLEX_FULL : DUPLEX_HALF;
+
+ return 0;
+}
+
+static struct cphy_ops aq100x_ops = {
+ .reset = aq100x_reset,
+ .intr_enable = aq100x_intr_enable,
+ .intr_disable = aq100x_intr_disable,
+ .intr_clear = aq100x_intr_clear,
+ .intr_handler = aq100x_intr_handler,
+ .autoneg_enable = aq100x_autoneg_enable,
+ .autoneg_restart = aq100x_autoneg_restart,
+ .advertise = aq100x_advertise,
+ .set_loopback = aq100x_set_loopback,
+ .set_speed_duplex = aq100x_set_speed_duplex,
+ .get_link_status = aq100x_get_link_status,
+ .power_down = aq100x_power_down,
+ .mmds = MDIO_DEVS_PMAPMD | MDIO_DEVS_PCS | MDIO_DEVS_PHYXS,
+};
+
+int t3_aq100x_phy_prep(struct cphy *phy, struct adapter *adapter, int phy_addr,
+ const struct mdio_ops *mdio_ops)
+{
+ unsigned int v, v2, gpio, wait;
+ int err;
+
+ cphy_init(phy, adapter, phy_addr, &aq100x_ops, mdio_ops,
+ SUPPORTED_1000baseT_Full | SUPPORTED_10000baseT_Full |
+ SUPPORTED_Autoneg | SUPPORTED_AUI, "1000/10GBASE-T");
+
+ /*
+ * The PHY has been out of reset ever since the system powered up. So
+ * we do a hard reset over here.
+ */
+ gpio = phy_addr ? F_GPIO10_OUT_VAL : F_GPIO6_OUT_VAL;
+ t3_set_reg_field(adapter, A_T3DBG_GPIO_EN, gpio, 0);
+ msleep(1);
+ t3_set_reg_field(adapter, A_T3DBG_GPIO_EN, gpio, gpio);
+
+ /*
+ * Give it enough time to load the firmware and get ready for mdio.
+ */
+ msleep(1000);
+ wait = 500; /* in 10ms increments */
+ do {
+ err = t3_mdio_read(phy, MDIO_MMD_VEND1, MDIO_CTRL1, &v);
+ if (err || v == 0xffff) {
+
+ /* Allow prep_adapter to succeed when ffff is read */
+
+ CH_WARN(adapter, "PHY%d: reset failed (0x%x, 0x%x).\n",
+ phy_addr, err, v);
+ goto done;
+ }
+
+ v &= AQ_RESET;
+ if (v)
+ msleep(10);
+ } while (v && --wait);
+ if (v) {
+ CH_WARN(adapter, "PHY%d: reset timed out (0x%x).\n",
+ phy_addr, v);
+
+ goto done; /* let prep_adapter succeed */
+ }
+
+ /* Datasheet says 3s max but this has been observed */
+ wait = (500 - wait) * 10 + 1000;
+ if (wait > 3000)
+ CH_WARN(adapter, "PHY%d: reset took %ums\n", phy_addr, wait);
+
+ /* Firmware version check. */
+ t3_mdio_read(phy, MDIO_MMD_VEND1, AQ_FW_VERSION, &v);
+ if (v != 30) {
+ CH_WARN(adapter, "PHY%d: unsupported firmware %d\n",
+ phy_addr, v);
+ return 0; /* allow t3_prep_adapter to succeed */
+ }
+
+ /*
+ * The PHY should start in really-low-power mode. Prepare it for normal
+ * operations.
+ */
+ err = t3_mdio_read(phy, MDIO_MMD_VEND1, MDIO_CTRL1, &v);
+ if (err)
+ return err;
+ if (v & AQ_LOWPOWER) {
+ err = t3_mdio_change_bits(phy, MDIO_MMD_VEND1, MDIO_CTRL1,
+ AQ_LOWPOWER, 0);
+ if (err)
+ return err;
+ msleep(10);
+ } else
+ CH_WARN(adapter, "PHY%d does not start in low power mode.\n",
+ phy_addr);
+
+ /*
+ * Verify XAUI settings, but let prep succeed no matter what.
+ */
+ v = v2 = 0;
+ t3_mdio_read(phy, MDIO_MMD_PHYXS, AQ_XAUI_RX_CFG, &v);
+ t3_mdio_read(phy, MDIO_MMD_PHYXS, AQ_XAUI_TX_CFG, &v2);
+ if (v != 0x1b || v2 != 0x1b)
+ CH_WARN(adapter,
+ "PHY%d: incorrect XAUI settings (0x%x, 0x%x).\n",
+ phy_addr, v, v2);
+
+done:
+ return err;
+}
projects / openwrt / staging / blogic.git / commitdiff