+++ /dev/null
-CONFIG_ALIGNMENT_TRAP=y
-CONFIG_ARCH_32BIT_OFF_T=y
-CONFIG_ARCH_HIBERNATION_POSSIBLE=y
-CONFIG_ARCH_KEEP_MEMBLOCK=y
-CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
-CONFIG_ARCH_MULTIPLATFORM=y
-CONFIG_ARCH_MULTI_CPU_AUTO=y
-# CONFIG_ARCH_MULTI_V4 is not set
-# CONFIG_ARCH_MULTI_V4T is not set
-CONFIG_ARCH_MULTI_V4_V5=y
-CONFIG_ARCH_MULTI_V5=y
-CONFIG_ARCH_MVEBU=y
-CONFIG_ARCH_NR_GPIO=0
-CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y
-CONFIG_ARCH_SELECT_MEMORY_MODEL=y
-CONFIG_ARCH_SPARSEMEM_ENABLE=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARM=y
-# CONFIG_ARMADA_37XX_WATCHDOG is not set
-# CONFIG_ARMADA_THERMAL is not set
-CONFIG_ARM_APPENDED_DTB=y
-CONFIG_ARM_ATAG_DTB_COMPAT=y
-CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER=y
-CONFIG_ARM_HAS_GROUP_RELOCS=y
-# CONFIG_ARM_KIRKWOOD_CPUIDLE is not set
-CONFIG_ARM_L1_CACHE_SHIFT=5
-# CONFIG_ARM_MVEBU_V7_CPUIDLE is not set
-CONFIG_ARM_PATCH_PHYS_VIRT=y
-# CONFIG_ARM_THUMB is not set
-CONFIG_ARM_UNWIND=y
-CONFIG_ATA=y
-CONFIG_ATAGS=y
-CONFIG_ATA_LEDS=y
-CONFIG_AUTO_ZRELADDR=y
-CONFIG_BINFMT_FLAT_ARGVP_ENVP_ON_STACK=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_BLK_MQ_PCI=y
-CONFIG_CACHE_FEROCEON_L2=y
-# CONFIG_CACHE_FEROCEON_L2_WRITETHROUGH is not set
-CONFIG_CC_HAVE_STACKPROTECTOR_TLS=y
-CONFIG_CC_IMPLICIT_FALLTHROUGH="-Wimplicit-fallthrough=5"
-CONFIG_CC_NO_ARRAY_BOUNDS=y
-CONFIG_CLKSRC_MMIO=y
-CONFIG_CLONE_BACKWARDS=y
-CONFIG_COMMON_CLK=y
-CONFIG_COMPACT_UNEVICTABLE_DEFAULT=1
-CONFIG_COMPAT_32BIT_TIME=y
-CONFIG_CPU_32v5=y
-CONFIG_CPU_ABRT_EV5T=y
-CONFIG_CPU_CACHE_VIVT=y
-CONFIG_CPU_COPY_FEROCEON=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-CONFIG_CPU_FEROCEON=y
-# CONFIG_CPU_FEROCEON_OLD_ID is not set
-CONFIG_CPU_IDLE=y
-CONFIG_CPU_IDLE_GOV_LADDER=y
-CONFIG_CPU_LITTLE_ENDIAN=y
-CONFIG_CPU_PABRT_LEGACY=y
-CONFIG_CPU_PM=y
-CONFIG_CPU_THERMAL=y
-CONFIG_CPU_THUMB_CAPABLE=y
-CONFIG_CPU_TLB_FEROCEON=y
-CONFIG_CPU_USE_DOMAINS=y
-CONFIG_CRC16=y
-# CONFIG_CRC32_SARWATE is not set
-CONFIG_CRC32_SLICEBY8=y
-CONFIG_CRYPTO_CRC32C=y
-CONFIG_CRYPTO_DEFLATE=y
-CONFIG_CRYPTO_DES=y
-CONFIG_CRYPTO_DEV_MARVELL=y
-CONFIG_CRYPTO_DEV_MARVELL_CESA=y
-CONFIG_CRYPTO_HASH_INFO=y
-CONFIG_CRYPTO_HW=y
-CONFIG_CRYPTO_LIB_BLAKE2S_GENERIC=y
-CONFIG_CRYPTO_LIB_DES=y
-CONFIG_CRYPTO_LIB_SHA1=y
-CONFIG_CRYPTO_LIB_UTILS=y
-CONFIG_CRYPTO_LZO=y
-CONFIG_CRYPTO_RNG2=y
-CONFIG_CRYPTO_ZSTD=y
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_LL=y
-CONFIG_DEBUG_LL_INCLUDE="debug/8250.S"
-CONFIG_DEBUG_MVEBU_UART0_ALTERNATE=y
-# CONFIG_DEBUG_MVEBU_UART1_ALTERNATE is not set
-CONFIG_DEBUG_UART_8250=y
-CONFIG_DEBUG_UART_8250_SHIFT=2
-CONFIG_DEBUG_UART_PHYS=0xf1012000
-CONFIG_DEBUG_UART_VIRT=0xfed12000
-CONFIG_DMA_OPS=y
-CONFIG_DNOTIFY=y
-CONFIG_DTC=y
-# CONFIG_EARLY_PRINTK is not set
-CONFIG_EDAC_ATOMIC_SCRUB=y
-CONFIG_EDAC_SUPPORT=y
-CONFIG_EXCLUSIVE_SYSTEM_RAM=y
-CONFIG_FIXED_PHY=y
-CONFIG_FIX_EARLYCON_MEM=y
-CONFIG_FORCE_PCI=y
-CONFIG_FWNODE_MDIO=y
-CONFIG_FW_LOADER_PAGED_BUF=y
-CONFIG_FW_LOADER_SYSFS=y
-CONFIG_GCC11_NO_ARRAY_BOUNDS=y
-CONFIG_GENERIC_ALLOCATOR=y
-CONFIG_GENERIC_ATOMIC64=y
-CONFIG_GENERIC_BUG=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CPU_AUTOPROBE=y
-CONFIG_GENERIC_EARLY_IOREMAP=y
-CONFIG_GENERIC_IDLE_POLL_SETUP=y
-CONFIG_GENERIC_IRQ_CHIP=y
-CONFIG_GENERIC_IRQ_MULTI_HANDLER=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
-CONFIG_GENERIC_LIB_DEVMEM_IS_ALLOWED=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GENERIC_PHY=y
-CONFIG_GENERIC_PINCONF=y
-CONFIG_GENERIC_SCHED_CLOCK=y
-CONFIG_GENERIC_SMP_IDLE_THREAD=y
-CONFIG_GENERIC_STRNCPY_FROM_USER=y
-CONFIG_GENERIC_STRNLEN_USER=y
-CONFIG_GLOB=y
-CONFIG_GPIOLIB_IRQCHIP=y
-CONFIG_GPIO_CDEV=y
-CONFIG_GPIO_MVEBU=y
-CONFIG_GRO_CELLS=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT_MAP=y
-CONFIG_HWMON=y
-CONFIG_HW_RANDOM=y
-CONFIG_HW_RANDOM_OMAP=y
-CONFIG_HZ_FIXED=0
-CONFIG_HZ_PERIODIC=y
-CONFIG_I2C=y
-CONFIG_I2C_BOARDINFO=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_MV64XXX=y
-# CONFIG_I2C_PXA is not set
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_IRQCHIP=y
-CONFIG_IRQSTACKS=y
-CONFIG_IRQ_DOMAIN=y
-CONFIG_IRQ_FORCED_THREADING=y
-CONFIG_IRQ_WORK=y
-CONFIG_KIRKWOOD_CLK=y
-CONFIG_KIRKWOOD_THERMAL=y
-CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_NETXBIG=y
-CONFIG_LEDS_NS2=y
-CONFIG_LIBFDT=y
-CONFIG_LOCK_DEBUGGING_SUPPORT=y
-CONFIG_LZO_COMPRESS=y
-CONFIG_LZO_DECOMPRESS=y
-CONFIG_MACH_KIRKWOOD=y
-CONFIG_MACH_MVEBU_ANY=y
-CONFIG_MANGLE_BOOTARGS=y
-CONFIG_MARVELL_PHY=y
-CONFIG_MDIO_BUS=y
-CONFIG_MDIO_DEVICE=y
-CONFIG_MDIO_DEVRES=y
-CONFIG_MEMFD_CREATE=y
-CONFIG_MIGRATION=y
-CONFIG_MODULES_USE_ELF_REL=y
-# CONFIG_MTD_CFI is not set
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_NAND_CORE=y
-CONFIG_MTD_NAND_ECC=y
-CONFIG_MTD_NAND_ECC_SW_HAMMING=y
-# CONFIG_MTD_NAND_MARVELL is not set
-CONFIG_MTD_NAND_ORION=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_MTD_SPI_NOR=y
-CONFIG_MTD_SPLIT_FIRMWARE=y
-CONFIG_MTD_SPLIT_UIMAGE_FW=y
-CONFIG_MTD_UBI=y
-CONFIG_MTD_UBI_BEB_LIMIT=20
-CONFIG_MTD_UBI_BLOCK=y
-CONFIG_MTD_UBI_WL_THRESHOLD=4096
-CONFIG_MV643XX_ETH=y
-CONFIG_MVEBU_CLK_COMMON=y
-CONFIG_MVEBU_MBUS=y
-CONFIG_MVMDIO=y
-# CONFIG_MVNETA is not set
-# CONFIG_MVPP2 is not set
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NEED_KUSER_HELPERS=y
-CONFIG_NEED_PER_CPU_KM=y
-CONFIG_NET_DEVLINK=y
-CONFIG_NET_DSA=y
-CONFIG_NET_DSA_MV88E6XXX=y
-CONFIG_NET_DSA_TAG_DSA=y
-CONFIG_NET_DSA_TAG_DSA_COMMON=y
-CONFIG_NET_DSA_TAG_EDSA=y
-CONFIG_NET_SELFTESTS=y
-CONFIG_NET_SWITCHDEV=y
-CONFIG_NLS=y
-CONFIG_NVMEM=y
-CONFIG_OF=y
-CONFIG_OF_ADDRESS=y
-CONFIG_OF_EARLY_FLATTREE=y
-CONFIG_OF_FLATTREE=y
-CONFIG_OF_GPIO=y
-CONFIG_OF_IRQ=y
-CONFIG_OF_KOBJ=y
-CONFIG_OF_MDIO=y
-CONFIG_OLD_SIGACTION=y
-CONFIG_OLD_SIGSUSPEND3=y
-CONFIG_ORION_IRQCHIP=y
-CONFIG_ORION_TIMER=y
-CONFIG_ORION_WATCHDOG=y
-CONFIG_OUTER_CACHE=y
-CONFIG_PAGE_OFFSET=0xC0000000
-CONFIG_PAGE_POOL=y
-CONFIG_PAGE_SIZE_LESS_THAN_256KB=y
-CONFIG_PAGE_SIZE_LESS_THAN_64KB=y
-CONFIG_PCI=y
-CONFIG_PCI_BRIDGE_EMUL=y
-CONFIG_PCI_DOMAINS=y
-CONFIG_PCI_DOMAINS_GENERIC=y
-CONFIG_PCI_MVEBU=y
-CONFIG_PERF_USE_VMALLOC=y
-CONFIG_PGTABLE_LEVELS=2
-CONFIG_PHYLIB=y
-CONFIG_PHYLINK=y
-# CONFIG_PHY_MVEBU_A3700_UTMI is not set
-# CONFIG_PHY_MVEBU_A38X_COMPHY is not set
-CONFIG_PHY_MVEBU_SATA=y
-CONFIG_PINCTRL=y
-CONFIG_PINCTRL_KIRKWOOD=y
-CONFIG_PINCTRL_MVEBU=y
-# CONFIG_PINCTRL_SINGLE is not set
-CONFIG_PINCTRL_SX150X=y
-CONFIG_PLAT_ORION=y
-CONFIG_POWER_RESET=y
-CONFIG_POWER_RESET_GPIO=y
-CONFIG_POWER_RESET_LINKSTATION=y
-CONFIG_POWER_SUPPLY=y
-CONFIG_PREEMPT_NONE_BUILD=y
-CONFIG_PTP_1588_CLOCK_OPTIONAL=y
-CONFIG_RANDSTRUCT_NONE=y
-CONFIG_RATIONAL=y
-CONFIG_REGMAP=y
-CONFIG_REGMAP_MMIO=y
-CONFIG_REGULATOR=y
-CONFIG_REGULATOR_FIXED_VOLTAGE=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_MV=y
-CONFIG_RTC_I2C_AND_SPI=y
-CONFIG_RTC_MC146818_LIB=y
-CONFIG_SCSI=y
-CONFIG_SCSI_COMMON=y
-CONFIG_SERIAL_8250_DEPRECATED_OPTIONS=y
-CONFIG_SERIAL_8250_FSL=y
-CONFIG_SERIAL_MCTRL_GPIO=y
-# CONFIG_SERIAL_MVEBU_UART is not set
-CONFIG_SERIAL_OF_PLATFORM=y
-CONFIG_SGL_ALLOC=y
-CONFIG_SG_POOL=y
-CONFIG_SOC_BUS=y
-CONFIG_SOFTIRQ_ON_OWN_STACK=y
-CONFIG_SPARSE_IRQ=y
-CONFIG_SPI=y
-# CONFIG_SPI_ARMADA_3700 is not set
-CONFIG_SPI_MASTER=y
-CONFIG_SPI_MEM=y
-CONFIG_SPI_ORION=y
-CONFIG_SPLIT_PTLOCK_CPUS=999999
-CONFIG_SRAM=y
-CONFIG_SRAM_EXEC=y
-CONFIG_SRCU=y
-CONFIG_SWPHY=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-CONFIG_THERMAL=y
-CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
-CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0
-CONFIG_THERMAL_GOV_STEP_WISE=y
-CONFIG_THERMAL_HWMON=y
-CONFIG_THERMAL_OF=y
-CONFIG_THREAD_INFO_IN_TASK=y
-CONFIG_TICK_CPU_ACCOUNTING=y
-CONFIG_TIMER_OF=y
-CONFIG_TIMER_PROBE=y
-CONFIG_TINY_SRCU=y
-CONFIG_UBIFS_FS=y
-CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
-CONFIG_UNWINDER_ARM=y
-CONFIG_USB=y
-CONFIG_USB_COMMON=y
-CONFIG_USB_LED_TRIG=y
-CONFIG_USB_SUPPORT=y
-CONFIG_USE_OF=y
-# CONFIG_VFP is not set
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_WAN=y
-CONFIG_WATCHDOG_CORE=y
-CONFIG_XXHASH=y
-CONFIG_XZ_DEC_ARM=y
-CONFIG_XZ_DEC_BCJ=y
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZLIB_DEFLATE=y
-CONFIG_ZLIB_INFLATE=y
-CONFIG_ZSTD_COMMON=y
-CONFIG_ZSTD_COMPRESS=y
-CONFIG_ZSTD_DECOMPRESS=y
define Device/Default
PROFILES := Default
-ifdef CONFIG_LINUX_6_6
DEVICE_DTS_DIR := $(DTS_DIR)/marvell
-endif
DEVICE_DTS = kirkwood-$(lastword $(subst _, ,$(1)))
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
KERNEL := kernel-bin | append-dtb | uImage none
+++ /dev/null
-From e977a103840c57d72b52cbc8c17f87f86ef9aa8d Mon Sep 17 00:00:00 2001
-From: Pawel Dembicki <paweldembicki@gmail.com>
-Date: Sat, 29 Oct 2022 22:57:38 +0200
-Subject: [PATCH] ARM: dts: kirkwood: Add Zyxel NSA310S board
-
-Zyxel NSA310S is a NAS based on Marvell kirkwood SoC.
-
-Specification:
- - Processor Marvell 88F6702 1 GHz
- - 256MB RAM
- - 128MB NAND
- - 1x GBE LAN port (PHY: Marvell 88E1318)
- - 2x USB 2.0
- - 1x SATA
- - 3x button
- - 7x leds
- - serial on J1 connector (115200 8N1) (GND-NOPIN-RX-TX-VCC)
-
-Tested-by: Tony Dinh <mibodhi@gmail.com>
-Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
-Acked-by: Adam Baker <linux@baker-net.org.uk>
-Reviewed-by: Andrew Lunn <andrew@lunn.ch>
-Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
----
- arch/arm/boot/dts/Makefile | 1 +
- arch/arm/boot/dts/kirkwood-nsa310s.dts | 259 +++++++++++++++++++++++++
- 2 files changed, 260 insertions(+)
- create mode 100644 arch/arm/boot/dts/kirkwood-nsa310s.dts
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -356,6 +356,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- kirkwood-ns2mini.dtb \
- kirkwood-nsa310.dtb \
- kirkwood-nsa310a.dtb \
-+ kirkwood-nsa310s.dtb \
- kirkwood-nsa320.dtb \
- kirkwood-nsa325.dtb \
- kirkwood-openblocks_a6.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-nsa310s.dts
-@@ -0,0 +1,259 @@
-+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-+/*
-+ * ZyXEL NSA310S Board Description
-+ * Copyright 2020-2022 Pawel Dembicki <paweldembicki@gmail.com>
-+ * Copyright (c) 2015-2021, Tony Dinh <mibodhi@gmail.com>
-+ * Copyright (c) 2014, Adam Baker <linux@baker-net.org.uk>
-+ * Based upon the board setup file created by Peter Schildmann
-+ */
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6281.dtsi"
-+#include <dt-bindings/leds/common.h>
-+
-+/ {
-+ model = "ZyXEL NSA310S";
-+ compatible = "zyxel,nsa310s", "marvell,kirkwood-88f6702", "marvell,kirkwood";
-+
-+ memory {
-+ device_type = "memory";
-+ reg = <0x00000000 0x10000000>;
-+ };
-+
-+ chosen {
-+ bootargs = "console=ttyS0,115200n8 earlyprintk";
-+ stdout-path = &uart0;
-+ };
-+
-+ gpio_poweroff {
-+ compatible = "gpio-poweroff";
-+ pinctrl-0 = <&pmx_pwr_off>;
-+ pinctrl-names = "default";
-+ gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ keys {
-+ compatible = "gpio-keys";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ pinctrl-0 = <&pmx_buttons>;
-+ pinctrl-names = "default";
-+
-+ power {
-+ label = "Power Button";
-+ linux,code = <KEY_POWER>;
-+ gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ copy {
-+ label = "Copy Button";
-+ linux,code = <KEY_COPY>;
-+ gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
-+ };
-+
-+ reset {
-+ label = "Reset Button";
-+ linux,code = <KEY_RESTART>;
-+ gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
-+ };
-+ };
-+
-+ leds {
-+ compatible = "gpio-leds";
-+ pinctrl-0 = <&pmx_leds>;
-+ pinctrl-names = "default";
-+
-+ led-1 {
-+ function = LED_FUNCTION_DISK_ERR;
-+ color = <LED_COLOR_ID_RED>;
-+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ led-2 {
-+ function = LED_FUNCTION_USB;
-+ color = <LED_COLOR_ID_GREEN>;
-+ gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
-+ linux,default-trigger = "usb-host";
-+ };
-+
-+ led-3 {
-+ function = LED_FUNCTION_DISK;
-+ color = <LED_COLOR_ID_GREEN>;
-+ gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
-+ linux,default-trigger = "ata1";
-+ };
-+
-+ led-4 {
-+ function = LED_FUNCTION_INDICATOR;
-+ color = <LED_COLOR_ID_GREEN>;
-+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ led-5 {
-+ function = LED_FUNCTION_INDICATOR;
-+ color = <LED_COLOR_ID_RED>;
-+ gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ led-6 {
-+ function = LED_FUNCTION_STATUS;
-+ color = <LED_COLOR_ID_GREEN>;
-+ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
-+ linux,default-trigger = "default-on";
-+ };
-+
-+ led-7 {
-+ function = LED_FUNCTION_STATUS;
-+ color = <LED_COLOR_ID_RED>;
-+ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
-+ };
-+ };
-+
-+ usb0_power: regulator@1 {
-+ compatible = "regulator-fixed";
-+ regulator-name = "USB Power";
-+
-+ regulator-min-microvolt = <5000000>;
-+ regulator-max-microvolt = <5000000>;
-+ regulator-always-on;
-+ regulator-boot-on;
-+ gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ sata1_power: regulator@2 {
-+ compatible = "regulator-fixed";
-+ regulator-name = "SATA1 Power";
-+
-+ regulator-min-microvolt = <5000000>;
-+ regulator-max-microvolt = <5000000>;
-+ regulator-always-on;
-+ regulator-boot-on;
-+ gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ thermal-zones {
-+ disk-thermal {
-+ polling-delay = <20000>;
-+ polling-delay-passive = <2000>;
-+
-+ thermal-sensors = <&hdd_temp>;
-+
-+ trips {
-+ disk_alert: disk-alert {
-+ temperature = <40000>;
-+ hysteresis = <5000>;
-+ type = "active";
-+ };
-+ disk_crit: disk-crit {
-+ temperature = <60000>;
-+ hysteresis = <2000>;
-+ type = "critical";
-+ };
-+ };
-+ };
-+ };
-+};
-+
-+
-+ð0 {
-+ status = "okay";
-+
-+ ethernet0-port@0 {
-+ phy-handle = <ðphy0>;
-+ };
-+};
-+
-+&i2c0 {
-+ status = "okay";
-+
-+ rtc@68 {
-+ compatible = "htk,ht1382";
-+ reg = <0x68>;
-+ };
-+};
-+
-+&mdio {
-+ status = "okay";
-+
-+ ethphy0: ethernet-phy@1 {
-+ reg = <1>;
-+ phy-mode = "rgmii-id";
-+ marvell,reg-init = <0x1 0x16 0x0 0x3>,
-+ <0x1 0x10 0x0 0x1017>,
-+ <0x1 0x11 0x0 0x4408>,
-+ <0x1 0x16 0x0 0x0>;
-+ };
-+};
-+
-+&nand {
-+ status = "okay";
-+ chip-delay = <35>;
-+
-+ partition@0 {
-+ label = "uboot";
-+ reg = <0x0000000 0x00c0000>;
-+ read-only;
-+ };
-+ partition@c0000 {
-+ label = "uboot_env";
-+ reg = <0x00c0000 0x0080000>;
-+ };
-+ partition@140000 {
-+ label = "ubi";
-+ reg = <0x0140000 0x7ec0000>;
-+ };
-+};
-+
-+&pciec {
-+ status = "okay";
-+};
-+
-+&pcie0 {
-+ status = "okay";
-+};
-+
-+&pinctrl {
-+ pinctrl-names = "default";
-+
-+ pmx_buttons: pmx-buttons {
-+ marvell,pins = "mpp24", "mpp25", "mpp26";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_leds: pmx-leds {
-+ marvell,pins = "mpp13", "mpp15", "mpp16", "mpp22", "mpp23",
-+ "mpp28", "mpp29";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_power: pmx-power {
-+ marvell,pins = "mpp21", "mpp33";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_pwr_off: pmx-pwr-off {
-+ marvell,pins = "mpp27";
-+ marvell,function = "gpio";
-+ };
-+};
-+
-+&rtc {
-+ status = "disabled";
-+};
-+
-+&sata {
-+ status = "okay";
-+ nr-ports = <1>;
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ hdd_temp: sata-port@0 {
-+ reg = <0>;
-+ #thermal-sensor-cells = <0>;
-+ };
-+};
-+
-+&uart0 {
-+ status = "okay";
-+};
+++ /dev/null
-From 5668d088ee4ea05db9daaae0645d1d1f579b20f9 Mon Sep 17 00:00:00 2001
-From: Pawel Dembicki <paweldembicki@gmail.com>
-Date: Mon, 3 Oct 2022 09:34:43 +0200
-Subject: ARM: dts: kirkwood: Add Endian 4i Edge 200 board
-
-Add Endian 4i Edge 200 is 5-port firewall.
-It have also clone: Endian UTM Mini (The same hardware, with added WLAN
-card).
-
-Hardware:
- - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz
- - Ram: 512MB (4x Nanya NT5TU128M8GE-AC)
- - NAND Flash: 512MB (Micron 29F4G08AAC)
- - Lan 1-4: 4x GBE (Marvell 88E6171R-TFJ2)
- - Lan 5: 1x GBE (Marvell 88E1116R-NNC1)
- - Storage: MicroSD Slot
- - MCPIE: MiniPCIe Slot present [fitted with SparkLan WPEA-110N/E
- (Atheros AR9280 chipset) in Endian UTM Mini WLAN only]
- - USB: 1x USB 2.0 port
- - Console: RJ-45 port
- - LEDs: 3x GPIO controlled
-
-Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
-Reviewed-by: Andrew Lunn <andrew@lunn.ch>
-Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
----
- arch/arm/boot/dts/Makefile | 1 +
- arch/arm/boot/dts/kirkwood-4i-edge-200.dts | 205 +++++++++++++++++++++++++++++
- 2 files changed, 206 insertions(+)
- create mode 100644 arch/arm/boot/dts/kirkwood-4i-edge-200.dts
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -300,6 +300,7 @@ dtb-$(CONFIG_ARCH_KEYSTONE) += \
- keystone-k2g-evm.dtb \
- keystone-k2g-ice.dtb
- dtb-$(CONFIG_MACH_KIRKWOOD) += \
-+ kirkwood-4i-edge-200.dtb \
- kirkwood-b3.dtb \
- kirkwood-blackarmor-nas220.dtb \
- kirkwood-c200-v1.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-4i-edge-200.dts
-@@ -0,0 +1,205 @@
-+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-+/*
-+ * Endian 4i Edge 200 Board Description
-+ * Note: Endian UTM Mini is hardware clone of Endian Edge 200
-+ * Copyright 2021-2022 Pawel Dembicki <paweldembicki@gmail.com>
-+ */
-+
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6281.dtsi"
-+#include <dt-bindings/leds/common.h>
-+
-+/ {
-+ model = "Endian 4i Edge 200";
-+ compatible = "endian,4i-edge-200", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-+
-+ memory {
-+ device_type = "memory";
-+ reg = <0x00000000 0x20000000>;
-+ };
-+
-+ chosen {
-+ bootargs = "console=ttyS0,115200n8";
-+ stdout-path = &uart0;
-+ };
-+
-+ leds {
-+ compatible = "gpio-leds";
-+ pinctrl-0 = <&pmx_led>;
-+ pinctrl-names = "default";
-+
-+ led-1 {
-+ function = LED_FUNCTION_SD;
-+ color = <LED_COLOR_ID_AMBER>;
-+ gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
-+ linux,default-trigger = "mmc0";
-+ };
-+
-+ led-2 {
-+ function = LED_FUNCTION_STATUS;
-+ color = <LED_COLOR_ID_AMBER>;
-+ gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ led-3 {
-+ function = LED_FUNCTION_STATUS;
-+ color = <LED_COLOR_ID_GREEN>;
-+ gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
-+ };
-+ };
-+};
-+
-+ð0 {
-+ status = "okay";
-+};
-+
-+ð0port {
-+ speed = <1000>;
-+ duplex = <1>;
-+};
-+
-+ð1 {
-+ status = "okay";
-+};
-+
-+ð1port {
-+ phy-handle = <ðphyb>;
-+};
-+
-+&mdio {
-+ status = "okay";
-+
-+ ethphyb: ethernet-phy@b {
-+ reg = <0x0b>;
-+
-+ marvell,reg-init =
-+ /* link-activity, bi-color mode 4 */
-+ <3 0x10 0xfff0 0xf>; /* Reg 3,16 <- 0xzzzf */
-+ };
-+
-+ switch0: switch@11 {
-+ compatible = "marvell,mv88e6085";
-+ reg = <0x11>;
-+
-+ ports {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ port@0 {
-+ reg = <0>;
-+ label = "port1";
-+ };
-+
-+ port@1 {
-+ reg = <1>;
-+ label = "port2";
-+ };
-+
-+ port@2 {
-+ reg = <2>;
-+ label = "port3";
-+ };
-+
-+ port@3 {
-+ reg = <3>;
-+ label = "port4";
-+ };
-+
-+ port@5 {
-+ reg = <5>;
-+ phy-mode = "rgmii-id";
-+ ethernet = <ð0port>;
-+
-+ fixed-link {
-+ speed = <1000>;
-+ full-duplex;
-+ };
-+ };
-+ };
-+ };
-+};
-+
-+&nand {
-+ status = "okay";
-+ pinctrl-0 = <&pmx_nand>;
-+ pinctrl-names = "default";
-+
-+ partition@0 {
-+ label = "u-boot";
-+ reg = <0x00000000 0x000a0000>;
-+ read-only;
-+ };
-+
-+ partition@a0000 {
-+ label = "u-boot-env";
-+ reg = <0x000a0000 0x00060000>;
-+ read-only;
-+ };
-+
-+ partition@100000 {
-+ label = "kernel";
-+ reg = <0x00100000 0x00400000>;
-+ };
-+
-+ partition@500000 {
-+ label = "ubi";
-+ reg = <0x00500000 0x1fb00000>;
-+ };
-+};
-+
-+&pciec {
-+ status = "okay";
-+};
-+
-+&pcie0 {
-+ status = "okay";
-+};
-+
-+&pinctrl {
-+ pinctrl-0 = <&pmx_sysrst>;
-+ pinctrl-names = "default";
-+
-+ pmx_sysrst: pmx-sysrst {
-+ marvell,pins = "mpp6";
-+ marvell,function = "sysrst";
-+ };
-+
-+ pmx_sdio_cd: pmx-sdio-cd {
-+ marvell,pins = "mpp28";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led: pmx-led {
-+ marvell,pins = "mpp34", "mpp35", "mpp49";
-+ marvell,function = "gpio";
-+ };
-+};
-+
-+&rtc {
-+ status = "okay";
-+};
-+
-+&sata_phy0 {
-+ status = "disabled";
-+};
-+
-+&sata_phy1 {
-+ status = "disabled";
-+};
-+
-+&sdio {
-+ pinctrl-0 = <&pmx_sdio_cd>;
-+ pinctrl-names = "default";
-+ status = "okay";
-+ cd-gpios = <&gpio0 28 9>;
-+};
-+
-+&uart0 {
-+ status = "okay";
-+};
-+
-+&usb0 {
-+ status = "okay";
-+};
+++ /dev/null
-From 8aea8659a5f3ae8dc63c9f632ce1f676a1483556 Mon Sep 17 00:00:00 2001
-From: Andrew Lunn <andrew@lunn.ch>
-Date: Fri, 7 Apr 2023 17:17:20 +0200
-Subject: [PATCH] ARM: dts: kirkwood: Add missing phy-mode and fixed links
-
-The DSA framework has got more picky about always having a phy-mode
-for the CPU port. The Kirkwood Ethernet is an RGMII port. Set the
-switch to impose the RGMII delays.
-
-Additionally, the cpu label has never actually been used in the
-binding, so remove it.
-
-Signed-off-by: Andrew Lunn <andrew@lunn.ch>
-Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
----
- arch/arm/boot/dts/kirkwood-dir665.dts | 3 ++-
- arch/arm/boot/dts/kirkwood-l-50.dts | 2 +-
- arch/arm/boot/dts/kirkwood-linksys-viper.dts | 3 ++-
- arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts | 3 ++-
- arch/arm/boot/dts/kirkwood-rd88f6281.dtsi | 2 +-
- 5 files changed, 8 insertions(+), 5 deletions(-)
-
---- a/arch/arm/boot/dts/kirkwood-dir665.dts
-+++ b/arch/arm/boot/dts/kirkwood-dir665.dts
-@@ -232,7 +232,7 @@
-
- port@6 {
- reg = <6>;
-- label = "cpu";
-+ phy-mode = "rgmii-id";
- ethernet = <ð0port>;
- fixed-link {
- speed = <1000>;
-@@ -251,6 +251,7 @@
- ethernet0-port@0 {
- speed = <1000>;
- duplex = <1>;
-+ phy-mode = "rgmii";
- };
- };
-
---- a/arch/arm/boot/dts/kirkwood-l-50.dts
-+++ b/arch/arm/boot/dts/kirkwood-l-50.dts
-@@ -254,7 +254,6 @@
-
- port@6 {
- reg = <6>;
-- label = "cpu";
- phy-mode = "rgmii-id";
- ethernet = <ð1port>;
- fixed-link {
-@@ -330,6 +329,7 @@
- ethernet1-port@0 {
- speed = <1000>;
- duplex = <1>;
-+ phy-mode = "rgmii";
- };
- };
-
---- a/arch/arm/boot/dts/kirkwood-linksys-viper.dts
-+++ b/arch/arm/boot/dts/kirkwood-linksys-viper.dts
-@@ -198,7 +198,7 @@
-
- port@5 {
- reg = <5>;
-- label = "cpu";
-+ phy-mode = "rgmii-id";
- ethernet = <ð0port>;
- fixed-link {
- speed = <1000>;
-@@ -221,6 +221,7 @@
- ethernet0-port@0 {
- speed = <1000>;
- duplex = <1>;
-+ phy-mode = "rgmii";
- };
- };
-
---- a/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
-+++ b/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
-@@ -149,7 +149,7 @@
-
- port@5 {
- reg = <5>;
-- label = "cpu";
-+ phy-mode = "rgmii-id";
- ethernet = <ð0port>;
- fixed-link {
- speed = <1000>;
-@@ -166,6 +166,7 @@
- ethernet0-port@0 {
- speed = <1000>;
- duplex = <1>;
-+ phy-mode = "rgmii";
- };
- };
-
---- a/arch/arm/boot/dts/kirkwood-rd88f6281.dtsi
-+++ b/arch/arm/boot/dts/kirkwood-rd88f6281.dtsi
-@@ -105,7 +105,7 @@
-
- port@5 {
- reg = <5>;
-- label = "cpu";
-+ phy-mode = "rgmii-id";
- ethernet = <ð0port>;
- fixed-link {
- speed = <1000>;
+++ /dev/null
---- a/arch/arm/boot/dts/kirkwood-ib62x0.dts
-+++ b/arch/arm/boot/dts/kirkwood-ib62x0.dts
-@@ -6,7 +6,14 @@
-
- / {
- model = "RaidSonic ICY BOX IB-NAS62x0 (Rev B)";
-- compatible = "raidsonic,ib-nas6210-b", "raidsonic,ib-nas6220-b", "raidsonic,ib-nas6210", "raidsonic,ib-nas6220", "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-+ compatible = "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-+
-+ aliases {
-+ led-boot = &led_green_os;
-+ led-failsafe = &led_red_os;
-+ led-running = &led_green_os;
-+ led-upgrade = &led_red_os;
-+ };
-
- memory {
- device_type = "memory";
-@@ -81,12 +88,12 @@
- &pmx_led_usb_transfer>;
- pinctrl-names = "default";
-
-- green-os {
-+ led_green_os: green-os {
- label = "ib62x0:green:os";
- gpios = <&gpio0 25 GPIO_ACTIVE_HIGH>;
-- default-state = "keep";
-+ default-state = "on";
- };
-- red-os {
-+ led_red_os: red-os {
- label = "ib62x0:red:os";
- gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
- };
-@@ -118,13 +125,13 @@
- };
-
- partition@100000 {
-- label = "uImage";
-- reg = <0x0100000 0x600000>;
-+ label = "second stage u-boot";
-+ reg = <0x100000 0x200000>;
- };
-
-- partition@700000 {
-- label = "root";
-- reg = <0x0700000 0xf900000>;
-+ partition@200000 {
-+ label = "ubi";
-+ reg = <0x200000 0xfe00000>;
- };
-
- };
+++ /dev/null
---- a/arch/arm/boot/dts/kirkwood-iconnect.dts
-+++ b/arch/arm/boot/dts/kirkwood-iconnect.dts
-@@ -8,6 +8,13 @@
- model = "Iomega Iconnect";
- compatible = "iom,iconnect-1.1", "iom,iconnect", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-
-+ aliases {
-+ led-boot = &led_power_blue;
-+ led-failsafe = &led_power_red;
-+ led-running = &led_power_blue;
-+ led-upgrade = &led_power_red;
-+ };
-+
- memory {
- device_type = "memory";
- reg = <0x00000000 0x10000000>;
-@@ -16,8 +23,6 @@
- chosen {
- bootargs = "console=ttyS0,115200n8 earlyprintk";
- stdout-path = &uart0;
-- linux,initrd-start = <0x4500040>;
-- linux,initrd-end = <0x4800000>;
- };
-
- ocp@f1000000 {
-@@ -89,12 +94,12 @@
- gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
- default-state = "on";
- };
-- power-blue {
-+ led_power_blue: power-blue {
- label = "power:blue";
- gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
-- default-state = "keep";
-+ default-state = "on";
- };
-- power-red {
-+ led_power_red: power-red {
- label = "power:red";
- gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
- };
-@@ -146,28 +151,23 @@
- status = "okay";
-
- partition@0 {
-- label = "uboot";
-- reg = <0x0000000 0xc0000>;
-+ label = "u-boot";
-+ reg = <0x0000000 0xe0000>;
- };
-
-- partition@a0000 {
-- label = "env";
-- reg = <0xa0000 0x20000>;
-+ partition@e0000 {
-+ label = "u-boot environment";
-+ reg = <0xe0000 0x100000>;
- };
-
- partition@100000 {
-- label = "zImage";
-- reg = <0x100000 0x300000>;
-- };
--
-- partition@540000 {
-- label = "initrd";
-- reg = <0x540000 0x300000>;
-+ label = "second stage u-boot";
-+ reg = <0x100000 0x200000>;
- };
-
-- partition@980000 {
-- label = "boot";
-- reg = <0x980000 0x1f400000>;
-+ partition@200000 {
-+ label = "ubi";
-+ reg = <0x200000 0x1fe00000>;
- };
- };
-
+++ /dev/null
---- a/arch/arm/boot/dts/kirkwood-dockstar.dts
-+++ b/arch/arm/boot/dts/kirkwood-dockstar.dts
-@@ -8,6 +8,13 @@
- model = "Seagate FreeAgent Dockstar";
- compatible = "seagate,dockstar", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-
-+ aliases {
-+ led-boot = &led_health;
-+ led-failsafe = &led_fault;
-+ led-running = &led_health;
-+ led-upgrade = &led_fault;
-+ };
-+
- memory {
- device_type = "memory";
- reg = <0x00000000 0x8000000>;
-@@ -42,12 +49,12 @@
- pinctrl-0 = <&pmx_led_green &pmx_led_orange>;
- pinctrl-names = "default";
-
-- health {
-+ led_health: health {
- label = "status:green:health";
- gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
-- default-state = "keep";
-+ default-state = "on";
- };
-- fault {
-+ led_fault: fault {
- label = "status:orange:fault";
- gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
- };
-@@ -78,18 +85,22 @@
-
- partition@0 {
- label = "u-boot";
-- reg = <0x0000000 0x100000>;
-- read-only;
-+ reg = <0x0000000 0xe0000>;
-+ };
-+
-+ partition@e0000 {
-+ label = "u-boot environment";
-+ reg = <0xe0000 0x100000>;
- };
-
- partition@100000 {
-- label = "uImage";
-- reg = <0x0100000 0x400000>;
-+ label = "second stage u-boot";
-+ reg = <0x100000 0x200000>;
- };
-
-- partition@500000 {
-- label = "data";
-- reg = <0x0500000 0xfb00000>;
-+ partition@200000 {
-+ label = "ubi";
-+ reg = <0x200000 0xfe00000>;
- };
- };
-
+++ /dev/null
---- a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
-+++ b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
-@@ -8,6 +8,13 @@
- model = "Iomega StorCenter ix2-200";
- compatible = "iom,ix2-200", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-
-+ aliases {
-+ led-boot = &led_power;
-+ led-failsafe = &led_health;
-+ led-running = &led_power;
-+ led-upgrade = &led_health;
-+ };
-+
- memory {
- device_type = "memory";
- reg = <0x00000000 0x10000000>;
-@@ -127,16 +134,16 @@
- &pmx_led_rebuild &pmx_led_health >;
- pinctrl-names = "default";
-
-- power_led {
-+ led_power: power_led {
- label = "status:white:power_led";
- gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
-- default-state = "keep";
-+ default-state = "on";
- };
- rebuild_led {
- label = "status:white:rebuild_led";
- gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
- };
-- health_led {
-+ led_health: health_led {
- label = "status:red:health_led";
- gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
- };
-@@ -186,19 +193,19 @@
- };
-
- partition@a0000 {
-- label = "env";
-+ label = "u-boot environment";
- reg = <0xa0000 0x20000>;
- read-only;
- };
-
- partition@100000 {
-- label = "uImage";
-- reg = <0x100000 0x300000>;
-+ label = "kernel";
-+ reg = <0x100000 0x400000>;
- };
-
-- partition@400000 {
-- label = "rootfs";
-- reg = <0x400000 0x1C00000>;
-+ partition@500000 {
-+ label = "ubi";
-+ reg = <0x500000 0x1C00000>;
- };
- };
-
-@@ -211,7 +218,7 @@
- };
-
- ð0 {
-- status = "okay";
-+ status = "disabled";
- ethernet0-port@0 {
- speed = <1000>;
- duplex = <1>;
+++ /dev/null
---- a/arch/arm/boot/dts/kirkwood-linksys-viper.dts
-+++ b/arch/arm/boot/dts/kirkwood-linksys-viper.dts
-@@ -24,6 +24,10 @@
- };
-
- aliases {
-+ led-boot = &led_white_health;
-+ led-failsafe = &led_white_health;
-+ led-running = &led_white_health;
-+ led-upgrade = &led_white_health;
- serial0 = &uart0;
- };
-
-@@ -56,9 +60,10 @@
- pinctrl-0 = < &pmx_led_white_health &pmx_led_white_pulse >;
- pinctrl-names = "default";
-
-- white-health {
-+ led_white_health: white-health {
- label = "viper:white:health";
- gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
-+ default-state = "on";
- };
-
- white-pulse {
-@@ -114,23 +119,23 @@
- };
-
- partition@200000 {
-- label = "kernel";
-- reg = <0x200000 0x2A0000>;
-+ label = "kernel1";
-+ reg = <0x200000 0x1A00000>;
- };
-
-- partition@4a0000 {
-- label = "rootfs";
-- reg = <0x4A0000 0x1760000>;
-+ partition@600000 {
-+ label = "rootfs1";
-+ reg = <0x600000 0x1600000>;
- };
-
- partition@1c00000 {
-- label = "alt_kernel";
-- reg = <0x1C00000 0x2A0000>;
-+ label = "kernel2";
-+ reg = <0x1C00000 0x1A00000>;
- };
-
-- partition@1ea0000 {
-- label = "alt_rootfs";
-- reg = <0x1EA0000 0x1760000>;
-+ partition@2000000 {
-+ label = "rootfs2";
-+ reg = <0x2000000 0x1600000>;
- };
-
- partition@3600000 {
+++ /dev/null
---- a/arch/arm/boot/dts/kirkwood-goflexnet.dts
-+++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts
-@@ -8,6 +8,13 @@
- model = "Seagate GoFlex Net";
- compatible = "seagate,goflexnet", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-
-+ aliases {
-+ led-boot = &led_health;
-+ led-failsafe = &led_fault;
-+ led-running = &led_health;
-+ led-upgrade = &led_fault;
-+ };
-+
- memory {
- device_type = "memory";
- reg = <0x00000000 0x8000000>;
-@@ -85,12 +92,12 @@
- >;
- pinctrl-names = "default";
-
-- health {
-+ led_health: health {
- label = "status:green:health";
- gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
-- default-state = "keep";
-+ default-state = "on";
- };
-- fault {
-+ led_fault: fault {
- label = "status:orange:fault";
- gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
- };
-@@ -159,18 +166,8 @@
- };
-
- partition@100000 {
-- label = "uImage";
-- reg = <0x0100000 0x400000>;
-- };
--
-- partition@500000 {
-- label = "pogoplug";
-- reg = <0x0500000 0x2000000>;
-- };
--
-- partition@2500000 {
-- label = "root";
-- reg = <0x02500000 0xd800000>;
-+ label = "ubi";
-+ reg = <0x0100000 0x0ff00000>;
- };
- };
-
+++ /dev/null
---- a/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi
-+++ b/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi
-@@ -112,40 +112,16 @@
-
- partition@0 {
- label = "uboot";
-- reg = <0x0000000 0x0100000>;
-+ reg = <0x0000000 0x00c0000>;
- read-only;
- };
- partition@100000 {
- label = "uboot_env";
-- reg = <0x0100000 0x0080000>;
-+ reg = <0x00c0000 0x0080000>;
- };
-- partition@180000 {
-- label = "key_store";
-- reg = <0x0180000 0x0080000>;
-- };
-- partition@200000 {
-- label = "info";
-- reg = <0x0200000 0x0080000>;
-- };
-- partition@280000 {
-- label = "etc";
-- reg = <0x0280000 0x0a00000>;
-- };
-- partition@c80000 {
-- label = "kernel_1";
-- reg = <0x0c80000 0x0a00000>;
-- };
-- partition@1680000 {
-- label = "rootfs1";
-- reg = <0x1680000 0x2fc0000>;
-- };
-- partition@4640000 {
-- label = "kernel_2";
-- reg = <0x4640000 0x0a00000>;
-- };
-- partition@5040000 {
-- label = "rootfs2";
-- reg = <0x5040000 0x2fc0000>;
-+ partition@140000 {
-+ label = "ubi";
-+ reg = <0x0140000 0x7ec0000>;
- };
- };
-
+++ /dev/null
---- a/arch/arm/boot/dts/kirkwood-nsa325.dts
-+++ b/arch/arm/boot/dts/kirkwood-nsa325.dts
-@@ -15,6 +15,13 @@
- model = "ZyXEL NSA325";
- compatible = "zyxel,nsa325", "marvell,kirkwood-88f6282", "marvell,kirkwood";
-
-+ aliases {
-+ led-boot = &led_green_sys;
-+ led-failsafe = &led_orange_sys;
-+ led-running = &led_green_sys;
-+ led-upgrade = &led_orange_sys;
-+ };
-+
- memory {
- device_type = "memory";
- reg = <0x00000000 0x20000000>;
-@@ -162,17 +169,19 @@
- &pmx_led_hdd1_green &pmx_led_hdd1_red>;
- pinctrl-names = "default";
-
-- green-sys {
-+ led_green_sys: green-sys {
- label = "nsa325:green:sys";
- gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
-+ default-state = "on";
- };
-- orange-sys {
-+ led_orange_sys: orange-sys {
- label = "nsa325:orange:sys";
- gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
- };
- green-hdd1 {
- label = "nsa325:green:hdd1";
- gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
-+ linux,default-trigger = "ata1";
- };
- red-hdd1 {
- label = "nsa325:red:hdd1";
-@@ -181,6 +190,7 @@
- green-hdd2 {
- label = "nsa325:green:hdd2";
- gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
-+ linux,default-trigger = "ata2";
- };
- red-hdd2 {
- label = "nsa325:red:hdd2";
-@@ -189,6 +199,7 @@
- green-usb {
- label = "nsa325:green:usb";
- gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
-+ linux,default-trigger = "usb-host";
- };
- green-copy {
- label = "nsa325:green:copy";
+++ /dev/null
---- a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
-+++ b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
-@@ -18,12 +18,20 @@
- compatible = "cloudengines,pogoplugv4", "marvell,kirkwood-88f6192",
- "marvell,kirkwood";
-
-+ aliases {
-+ led-boot = &led_health;
-+ led-failsafe = &led_fault;
-+ led-running = &led_health;
-+ led-upgrade = &led_fault;
-+ };
-+
- memory {
- device_type = "memory";
- reg = <0x00000000 0x08000000>;
- };
-
- chosen {
-+ bootargs = "console=ttyS0,115200";
- stdout-path = "uart0:115200n8";
- };
-
-@@ -37,8 +45,8 @@
- eject {
- debounce-interval = <50>;
- wakeup-source;
-- linux,code = <KEY_EJECTCD>;
-- label = "Eject Button";
-+ linux,code = <KEY_RESTART>;
-+ label = "Reset";
- gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
- };
- };
-@@ -48,12 +56,12 @@
- pinctrl-0 = <&pmx_led_green &pmx_led_red>;
- pinctrl-names = "default";
-
-- health {
-+ led_health: health {
- label = "pogoplugv4:green:health";
- gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
- default-state = "on";
- };
-- fault {
-+ led_fault: fault {
- label = "pogoplugv4:red:fault";
- gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
- };
-@@ -137,29 +145,19 @@
- #size-cells = <1>;
-
- partition@0 {
-- label = "u-boot";
-- reg = <0x00000000 0x200000>;
-+ label = "uboot";
-+ reg = <0x00000000 0x1c0000>;
- read-only;
- };
-
-- partition@200000 {
-- label = "uImage";
-- reg = <0x00200000 0x300000>;
-- };
--
-- partition@500000 {
-- label = "uImage2";
-- reg = <0x00500000 0x300000>;
-- };
--
-- partition@800000 {
-- label = "failsafe";
-- reg = <0x00800000 0x800000>;
-+ partition@1c0000 {
-+ label = "uboot_env";
-+ reg = <0x001c0000 0x40000>;
- };
-
-- partition@1000000 {
-- label = "root";
-- reg = <0x01000000 0x7000000>;
-+ partition@200000 {
-+ label = "ubi";
-+ reg = <0x00200000 0x7e00000>;
- };
- };
- };
+++ /dev/null
---- a/arch/arm/boot/dts/kirkwood-pogo_e02.dts
-+++ b/arch/arm/boot/dts/kirkwood-pogo_e02.dts
-@@ -20,6 +20,13 @@
- compatible = "cloudengines,pogoe02", "marvell,kirkwood-88f6281",
- "marvell,kirkwood";
-
-+ aliases {
-+ led-boot = &led_health;
-+ led-failsafe = &led_fault;
-+ led-running = &led_health;
-+ led-upgrade = &led_fault;
-+ };
-+
- memory {
- device_type = "memory";
- reg = <0x00000000 0x10000000>;
-@@ -33,12 +40,12 @@
- gpio-leds {
- compatible = "gpio-leds";
-
-- health {
-+ led_health: health {
- label = "pogo_e02:green:health";
- gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
-- default-state = "keep";
-+ default-state = "on";
- };
-- fault {
-+ led_fault: fault {
- label = "pogo_e02:orange:fault";
- gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
- };
-@@ -95,24 +102,24 @@
- status = "okay";
-
- partition@0 {
-- label = "u-boot";
-- reg = <0x0000000 0x100000>;
-+ label = "uboot";
-+ reg = <0x0 0xe0000>;
- read-only;
- };
-
-- partition@100000 {
-- label = "uImage";
-- reg = <0x0100000 0x400000>;
-+ partition@e0000 {
-+ label = "uboot_env";
-+ reg = <0xe0000 0x20000>;
- };
-
-- partition@500000 {
-- label = "pogoplug";
-- reg = <0x0500000 0x2000000>;
-+ partition@100000 {
-+ label = "second_stage_uboot";
-+ reg = <0x100000 0x100000>;
- };
-
-- partition@2500000 {
-- label = "root";
-- reg = <0x02500000 0x5b00000>;
-+ partition@200000 {
-+ label = "ubi";
-+ reg = <0x200000 0x7e00000>;
- };
- };
-
+++ /dev/null
---- a/arch/arm/boot/dts/kirkwood-l-50.dts
-+++ b/arch/arm/boot/dts/kirkwood-l-50.dts
-@@ -18,6 +18,13 @@
- reg = <0x00000000 0x20000000>;
- };
-
-+ aliases {
-+ led-boot = &led_status_green;
-+ led-failsafe = &led_status_red;
-+ led-running = &led_status_green;
-+ led-upgrade = &led_status_red;
-+ };
-+
- chosen {
- bootargs = "console=ttyS0,115200n8";
- stdout-path = &uart0;
-@@ -95,12 +102,12 @@
- leds {
- compatible = "gpio-leds";
-
-- status_green {
-+ led_status_green: status_green {
- label = "l-50:green:status";
- gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
- };
-
-- status_red {
-+ led_status_red: status_red {
- label = "l-50:red:status";
- gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
- };
-@@ -349,13 +356,8 @@
- };
-
- partition@100000 {
-- label = "kernel-1";
-- reg = <0x00100000 0x00800000>;
-- };
--
-- partition@900000 {
-- label = "rootfs-1";
-- reg = <0x00900000 0x07100000>;
-+ label = "ubi";
-+ reg = <0x00100000 0x07900000>;
- };
-
- partition@7a00000 {
+++ /dev/null
---- a/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
-+++ b/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
-@@ -78,13 +78,8 @@
- };
-
- partition@100000 {
-- label = "uImage";
-- reg = <0x0100000 0x400000>;
-- };
--
-- partition@500000 {
-- label = "root";
-- reg = <0x0500000 0x1fb00000>;
-+ label = "ubi";
-+ reg = <0x0100000 0x1ff00000>;
- };
- };
-
---- a/arch/arm/boot/dts/kirkwood-sheevaplug.dts
-+++ b/arch/arm/boot/dts/kirkwood-sheevaplug.dts
-@@ -13,6 +13,13 @@
- model = "Globalscale Technologies SheevaPlug";
- compatible = "globalscale,sheevaplug", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-
-+ aliases {
-+ led-boot = &led_health;
-+ led-failsafe = &led_health;
-+ led-running = &led_health;
-+ led-upgrade = &led_health;
-+ };
-+
- ocp@f1000000 {
- mvsdio@90000 {
- pinctrl-0 = <&pmx_sdio>;
-@@ -28,10 +35,10 @@
- pinctrl-0 = <&pmx_led_blue &pmx_led_red>;
- pinctrl-names = "default";
-
-- health {
-+ led_health: health {
- label = "sheevaplug:blue:health";
- gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
-- default-state = "keep";
-+ default-state = "on";
- };
-
- misc {
+++ /dev/null
---- a/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
-+++ b/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
-@@ -19,6 +19,13 @@
- reg = <0x00000000 0x10000000>;
- };
-
-+ aliases {
-+ led-boot = &led_power;
-+ led-failsafe = &led_power;
-+ led-running = &led_power;
-+ led-upgrade = &led_power;
-+ };
-+
- chosen {
- bootargs = "console=ttyS0,115200n8 earlyprintk";
- stdout-path = &uart0;
-@@ -115,7 +122,7 @@
- &pmx_led_blue_backup >;
- pinctrl-names = "default";
-
-- power_led {
-+ led_power: power_led {
- label = "status:blue:power_led";
- gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
- default-state = "keep";
-@@ -129,11 +136,13 @@
- disk1_led {
- label = "status:blue:disk1_led";
- gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
-+ linux,default-trigger = "ata1";
- };
-
- disk2_led {
- label = "status:blue:disk2_led";
- gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
-+ linux,default-trigger = "ata2";
- };
-
- backup_led {
-@@ -150,7 +159,13 @@
-
- power-button {
- label = "Power Button";
-- linux,code = <KEY_POWER>;
-+ /* Power button and INT pin from PHY are both connected
-+ * to this GPIO. Every network restart causes PHY restart
-+ * and button is pressed. It's difficult to use it as
-+ * KEY_POWER without changes in kernel (or netifd) so
-+ * the button is configured as regular one.
-+ */
-+ linux,code = <BTN_1>;
- gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
- };
-
-@@ -208,18 +223,13 @@
- };
-
- partition@200000 {
-- label = "uImage";
-+ label = "kernel";
- reg = <0x0200000 0x600000>;
- };
-
- partition@800000 {
-- label = "minirootfs";
-- reg = <0x0800000 0x1000000>;
-- };
--
-- partition@1800000 {
-- label = "jffs2";
-- reg = <0x1800000 0x6800000>;
-+ label = "ubi";
-+ reg = <0x0800000 0x7800000>;
- };
- };
-
+++ /dev/null
---- a/arch/arm/boot/dts/kirkwood-c200-v1.dts
-+++ b/arch/arm/boot/dts/kirkwood-c200-v1.dts
-@@ -14,6 +14,14 @@
- model = "Ctera C200 V1";
- compatible = "ctera,c200-v1", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-
-+
-+ aliases {
-+ led-boot = &led_status_green;
-+ led-failsafe = &led_status_red;
-+ led-running = &led_status_green;
-+ led-upgrade = &led_status_red;
-+ };
-+
- chosen {
- bootargs = "console=ttyS0,115200";
- stdout-path = &uart0;
-@@ -78,6 +86,7 @@
- function-enumerator = <1>;
- color = <LED_COLOR_ID_GREEN>;
- gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
-+ linux,default-trigger = "ata1";
- };
-
- led-2 {
-@@ -85,6 +94,7 @@
- function-enumerator = <2>;
- color = <LED_COLOR_ID_GREEN>;
- gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
-+ linux,default-trigger = "ata2";
- };
-
- led-3 {
-@@ -94,13 +104,13 @@
- gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
- };
-
-- led-4 {
-+ led_status_red: led-4 {
- function = LED_FUNCTION_STATUS;
- color = <LED_COLOR_ID_RED>;
- gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
- };
-
-- led-5 {
-+ led_status_green: led-5 {
- function = LED_FUNCTION_STATUS;
- color = <LED_COLOR_ID_GREEN>;
- gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
-@@ -240,7 +250,7 @@
- };
-
- partition@7a00000 {
-- label = "rootfs";
-+ label = "ubi";
- reg = <0x7a00000 0x8600000>;
- };
- };
+++ /dev/null
---- a/arch/arm/boot/dts/kirkwood-nsa310s.dts
-+++ b/arch/arm/boot/dts/kirkwood-nsa310s.dts
-@@ -16,6 +16,13 @@
- model = "ZyXEL NSA310S";
- compatible = "zyxel,nsa310s", "marvell,kirkwood-88f6702", "marvell,kirkwood";
-
-+ aliases {
-+ led-boot = &led_green_sys;
-+ led-failsafe = &led_red_sys;
-+ led-running = &led_green_sys;
-+ led-upgrade = &led_red_sys;
-+ };
-+
- memory {
- device_type = "memory";
- reg = <0x00000000 0x10000000>;
-@@ -96,14 +103,16 @@
- gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
- };
-
-- led-6 {
-+ led_green_sys: led-6 {
-+ label = "nsa310s:green:sys";
- function = LED_FUNCTION_STATUS;
- color = <LED_COLOR_ID_GREEN>;
- gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "default-on";
- };
-
-- led-7 {
-+ led_red_sys: led-7 {
-+ label = "nsa310s:red:sys";
- function = LED_FUNCTION_STATUS;
- color = <LED_COLOR_ID_RED>;
- gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+++ /dev/null
---- a/arch/arm/boot/dts/kirkwood-4i-edge-200.dts
-+++ b/arch/arm/boot/dts/kirkwood-4i-edge-200.dts
-@@ -20,6 +20,13 @@
- reg = <0x00000000 0x20000000>;
- };
-
-+ aliases {
-+ led-boot = &led_status_green;
-+ led-failsafe = &led_status_orange;
-+ led-running = &led_status_green;
-+ led-upgrade = &led_status_orange;
-+ };
-+
- chosen {
- bootargs = "console=ttyS0,115200n8";
- stdout-path = &uart0;
-@@ -37,13 +44,15 @@
- linux,default-trigger = "mmc0";
- };
-
-- led-2 {
-+ led_status_orange: led-2 {
-+ label = "orange:status";
- function = LED_FUNCTION_STATUS;
- color = <LED_COLOR_ID_AMBER>;
- gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
- };
-
-- led-3 {
-+ led_status_green: led-3 {
-+ label = "green:status";
- function = LED_FUNCTION_STATUS;
- color = <LED_COLOR_ID_GREEN>;
- gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+++ /dev/null
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -375,6 +375,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- kirkwood-rs411.dtb \
- kirkwood-sheevaplug.dtb \
- kirkwood-sheevaplug-esata.dtb \
-+ kirkwood-stora.dtb \
- kirkwood-t5325.dtb \
- kirkwood-topkick.dtb \
- kirkwood-ts219-6281.dtb \
+++ /dev/null
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -310,6 +310,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- kirkwood-db-88f6282.dtb \
- kirkwood-dir665.dtb \
- kirkwood-dns320.dtb \
-+ kirkwood-dns320l.dtb \
- kirkwood-dns325.dtb \
- kirkwood-dockstar.dtb \
- kirkwood-dreamplug.dtb \
---- a/arch/arm/boot/dts/kirkwood-dns320l.dts
-+++ b/arch/arm/boot/dts/kirkwood-dns320l.dts
-@@ -32,6 +32,13 @@
- reg = <0x00000000 0x10000000>;
- };
-
-+ aliases {
-+ led-boot = &led_orange_usb;
-+ led-failsafe = &led_orange_usb;
-+ led-running = &led_orange_usb;
-+ led-upgrade = &led_orange_usb;
-+ };
-+
- chosen {
- bootargs = "console=ttyS0,115200n8 earlyprintk";
- stdout-path = &uart0;
-@@ -68,7 +75,7 @@
- linux,default-trigger = "usbport";
- };
-
-- orange-usb {
-+ led_orange_usb: orange-usb {
- label = "dns320l:usb:orange";
- gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
- };
+++ /dev/null
---- a/arch/arm/mach-mvebu/Kconfig
-+++ b/arch/arm/mach-mvebu/Kconfig
-@@ -115,6 +115,7 @@ config MACH_DOVE
- config MACH_KIRKWOOD
- bool "Marvell Kirkwood boards"
- depends on ARCH_MULTI_V5
-+ select ARCH_WANT_LIBATA_LEDS
- select CPU_FEROCEON
- select GPIOLIB
- select KIRKWOOD_CLK
+++ /dev/null
-The WRT1900AC among other Linksys routers uses a dual-firmware layout.
-Dynamically rename the active partition to "ubi".
-
-Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
----
---- a/drivers/mtd/parsers/ofpart_core.c
-+++ b/drivers/mtd/parsers/ofpart_core.c
-@@ -38,6 +38,8 @@ static bool node_has_compatible(struct d
- return of_get_property(pp, "compatible", NULL);
- }
-
-+static int mangled_rootblock;
-+
- static int parse_fixed_partitions(struct mtd_info *master,
- const struct mtd_partition **pparts,
- struct mtd_part_parser_data *data)
-@@ -47,6 +49,7 @@ static int parse_fixed_partitions(struct
- struct mtd_partition *parts;
- struct device_node *mtd_node;
- struct device_node *ofpart_node;
-+ const char *owrtpart = "ubi";
- const char *partname;
- struct device_node *pp;
- int nr_parts, i, ret = 0;
-@@ -152,9 +155,15 @@ static int parse_fixed_partitions(struct
- parts[i].size = of_read_number(reg + a_cells, s_cells);
- parts[i].of_node = pp;
-
-- partname = of_get_property(pp, "label", &len);
-- if (!partname)
-- partname = of_get_property(pp, "name", &len);
-+ if (mangled_rootblock && (i == mangled_rootblock)) {
-+ partname = owrtpart;
-+ } else {
-+ partname = of_get_property(pp, "label", &len);
-+
-+ if (!partname)
-+ partname = of_get_property(pp, "name", &len);
-+ }
-+
- parts[i].name = partname;
-
- if (of_get_property(pp, "read-only", &len))
-@@ -271,6 +280,18 @@ static int __init ofpart_parser_init(voi
- return 0;
- }
-
-+static int __init active_root(char *str)
-+{
-+ get_option(&str, &mangled_rootblock);
-+
-+ if (!mangled_rootblock)
-+ return 1;
-+
-+ return 1;
-+}
-+
-+__setup("mangled_rootblock=", active_root);
-+
- static void __exit ofpart_parser_exit(void)
- {
- deregister_mtd_parser(&ofpart_parser);
+++ /dev/null
---- a/arch/arm/boot/dts/kirkwood-blackarmor-nas220.dts
-+++ b/arch/arm/boot/dts/kirkwood-blackarmor-nas220.dts
-@@ -17,6 +17,13 @@
- compatible = "seagate,blackarmor-nas220","marvell,kirkwood-88f6192",
- "marvell,kirkwood";
-
-+ aliases {
-+ led-boot = &led_status_amber;
-+ led-failsafe = &led_status_amber;
-+ led-running = &led_status_blue;
-+ led-upgrade = &led_status_amber;
-+ };
-+
- memory { /* 128 MB */
- device_type = "memory";
- reg = <0x00000000 0x8000000>;
-@@ -36,14 +43,14 @@
- compatible = "gpio-keys";
-
- reset {
-- label = "Reset";
-- linux,code = <KEY_POWER>;
-+ label = "Reset Button";
-+ linux,code = <KEY_RESTART>;
- gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
- };
-
-- button {
-- label = "Power";
-- linux,code = <KEY_SLEEP>;
-+ power {
-+ label = "Power Button";
-+ linux,code = <KEY_POWER>;
- gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
- };
- };
-@@ -51,11 +58,27 @@
- gpio-leds {
- compatible = "gpio-leds";
-
-- blue-power {
-+ led_power_blue: power_blue {
- label = "nas220:blue:power";
- gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "default-on";
- };
-+
-+ disk_blue {
-+ label = "nas220:blue:disk";
-+ gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
-+ linux,default-trigger = "disk-activity";
-+ };
-+
-+ led_status_blue: status_blue {
-+ label = "nas220:blue:status";
-+ gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ led_status_amber: status_amber {
-+ label = "nas220:amber:status";
-+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
-+ };
- };
-
- regulators {
-@@ -153,6 +176,33 @@
-
- &nand {
- status = "okay";
-+
-+ partitions {
-+ compatible = "fixed-partitions";
-+
-+ partition@0 {
-+ label = "uboot";
-+ reg = <0x0 0xa0000>;
-+ read-only;
-+ };
-+
-+ partition@a0000 {
-+ label = "uboot-env";
-+ reg = <0xa0000 0x10000>;
-+ read-only;
-+ };
-+
-+ partition@b0000 {
-+ label = "reserved";
-+ reg = <0xb0000 0x10000>;
-+ read-only;
-+ };
-+
-+ partition@c0000 {
-+ label = "ubi";
-+ reg = <0xc0000 0x1e80000>;
-+ };
-+ };
- };
-
- &mdio {
projects / openwrt / staging / stintel.git / commitdiff