realtek: add support for ZyXEL GS1900-24E

The ZyXEL GS1900-24E is a 24 port gigabit switch similar to other GS1900
switches.

Specifications
--------------
* Device:    ZyXEL GS1900-24E
* SoC:       Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash:     16 MiB Macronix MX25L12835F
* RAM:       128 MiB DDR2 SDRAM Nanya NT5TU128M8GE
* Ethernet:  24x 10/100/1000 Mbps
* LEDs:      1 PWR LED (green, not configurable)
             1 SYS LED (green, configurable)
             24 ethernet port link/activity LEDs (green, SoC controlled)
* Buttons:   1 "RESET" button on front panel
* Switch:    1 Power switch on rear of device
* Power      120-240V AC C13
* UART:      1 serial header (JP2) with populated standard pin connector on
             the left side of the PCB.
             Pinout (front to back):
             + Pin 1 - VCC marked with white dot
             + Pin 2 - RX
             + Pin 3 - TX
             + PIn 4 - GND

Serial connection parameters:  115200 8N1.

Installation
------------

OEM upgrade method:

* Log in to OEM management web interface
* Navigate to Maintenance > Firmware
* Select the HTTP radio button
* Select the Active radio button
* Use the browse button to locate the
realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
file and select open so File Path is updated with filename.
* Select the Apply button. Screen will display "Prepare
for firmware upgrade ...".
*Wait until screen shows "Do you really want to reboot?"
then select the OK button
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
   > sysupgrade -n /tmp/realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
   it may be necessary to restart the network (/etc/init.d/network restart) on
   the running initramfs image.

U-Boot TFTP method:

* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
  space bar, and enable the network:
   > rtk network on
* Since the GS1900-24E is a dual-partition device, you want to keep the OEM
  firmware on the backup partition for the time being. OpenWrt can only boot
  from the first partition anyway (hardcoded in the DTS). To make sure we are
  manipulating the first partition, issue the following commands:
  > setsys bootpartition 0
  > savesys
* Download the image onto the device and boot from it:
   > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
   > bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
   > sysupgrade -n /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
   it may be necessary to restart the network (/etc/init.d/network restart) on
   the running initramfs image.

Signed-off-by: Raylynn Knight <rayknight@me.com>
(cherry picked from commit b515ad10a6e1bd5c5da0ea95366fb19c92a75dea)

diff --git a/package/boot/uboot-envtools/files/realtek b/package/boot/uboot-envtools/files/realtek
index 99a73a6ab112a20cbaa4023e4fb12a30cd85be3c..af48d270785c73020b4c94a54c18d3a9decd9dc1 100644 (file)
--- a/package/boot/uboot-envtools/files/realtek
+++ b/package/boot/uboot-envtools/files/realtek
@@ -17,6 +17,7 @@ zyxel,gs1900-8hp-v2|\
 zyxel,gs1900-10hp|\
 zyxel,gs1900-16|\
 zyxel,gs1900-24-v1|\
+zyxel,gs1900-24e|\
 zyxel,gs1900-24hp-v1|\
 zyxel,gs1900-24hp-v2)
        idx="$(find_mtd_index u-boot-env)"

diff --git a/target/linux/realtek/dts-5.10/rtl8382_zyxel_gs1900-24e.dts b/target/linux/realtek/dts-5.10/rtl8382_zyxel_gs1900-24e.dts
new file mode 100644 (file)
index 0000000..3d00034
--- /dev/null
+++ b/target/linux/realtek/dts-5.10/rtl8382_zyxel_gs1900-24e.dts
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "rtl8380_zyxel_gs1900.dtsi"
+
+/ {
+       compatible = "zyxel,gs1900-24e", "realtek,rtl838x-soc";
+       model = "ZyXEL GS1900-24E";
+};
+
+&mdio {
+       EXTERNAL_PHY(0)
+       EXTERNAL_PHY(1)
+       EXTERNAL_PHY(2)
+       EXTERNAL_PHY(3)
+       EXTERNAL_PHY(4)
+       EXTERNAL_PHY(5)
+       EXTERNAL_PHY(6)
+       EXTERNAL_PHY(7)
+
+       EXTERNAL_PHY(16)
+       EXTERNAL_PHY(17)
+       EXTERNAL_PHY(18)
+       EXTERNAL_PHY(19)
+       EXTERNAL_PHY(20)
+       EXTERNAL_PHY(21)
+       EXTERNAL_PHY(22)
+       EXTERNAL_PHY(23)
+};
+
+&switch0 {
+       ports {
+               SWITCH_PORT(1, 1, qsgmii)
+               SWITCH_PORT(0, 2, qsgmii)
+               SWITCH_PORT(3, 3, qsgmii)
+               SWITCH_PORT(2, 4, qsgmii)
+               SWITCH_PORT(5, 5, qsgmii)
+               SWITCH_PORT(4, 6, qsgmii)
+               SWITCH_PORT(7, 7, qsgmii)
+               SWITCH_PORT(6, 8, qsgmii)
+
+               SWITCH_PORT(9, 9, internal)
+               SWITCH_PORT(8, 10, internal)
+               SWITCH_PORT(11, 11, internal)
+               SWITCH_PORT(10, 12, internal)
+               SWITCH_PORT(13, 13, internal)
+               SWITCH_PORT(12, 14, internal)
+               SWITCH_PORT(15, 15, internal)
+               SWITCH_PORT(14, 16, internal)
+
+               SWITCH_PORT(17, 17, qsgmii)
+               SWITCH_PORT(16, 18, qsgmii)
+               SWITCH_PORT(19, 19, qsgmii)
+               SWITCH_PORT(18, 20, qsgmii)
+               SWITCH_PORT(21, 21, qsgmii)
+               SWITCH_PORT(20, 22, qsgmii)
+               SWITCH_PORT(23, 23, qsgmii)
+               SWITCH_PORT(22, 24, qsgmii)
+       };
+};
+
+&gpio1 {
+       /delete-node/ poe_enable;
+};

diff --git a/target/linux/realtek/image/rtl838x.mk b/target/linux/realtek/image/rtl838x.mk
index e17dc8c62dd5615438eda9efac10d009559abe2f..289e37db1632579e1b3634734c46089e25e9048c 100644 (file)
--- a/target/linux/realtek/image/rtl838x.mk
+++ b/target/linux/realtek/image/rtl838x.mk
@@ -153,6 +153,14 @@ define Device/zyxel_gs1900-24-v1
 endef
 TARGET_DEVICES += zyxel_gs1900-24-v1
 
+define Device/zyxel_gs1900-24e
+  $(Device/zyxel_gs1900)
+  SOC := rtl8382
+  DEVICE_MODEL := GS1900-24E
+  ZYXEL_VERS := AAHK
+endef
+TARGET_DEVICES += zyxel_gs1900-24e
+
 define Device/zyxel_gs1900-24hp-v1
   $(Device/zyxel_gs1900)
   SOC := rtl8382