--- /dev/null
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal@milecki.pl>
+Subject: [PATCH] ARM: BCM5301X: Set 5 GHz wireless frequency limits on Netgear
+ R8000
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Netgear R8000 is a tri-band home router. It has three BCM43602 chipsets
+two of them for 5 GHz band. Both seem the same and their firmwares
+report the same set of channels. The problem is due to hardware / board
+design there are extra limitations that should be respected.
+
+First PHY should be used for U-NII-2 and U-NII-3. Third PHY should be
+used for U-NII-1. Using them in a different way may result in wireless
+not working or in noticeably reduced performance. Basic version of this
+info was provided by Broadcom employee, then it has been verified by me
+using original vendor firmware (which has limitations hardcoded in UI).
+
+This patch uses recently introduced ieee80211-freq-limit property to
+describe these limitations at DT level.
+
+Referencing PCIe devices in DT required specifying all related bridges.
+Below you can see (a bit complex) PCI tree from R8000 that explains all
+entries that I needed to put in DT.
+
+0000:00:00.0 14e4:8012 Bridge Device
+└─ 0000:01:00.0 14e4:aa52 Network Controller
+
+0001:00:00.0 14e4:8012 Bridge Device
+└─ 0001:01:00.0 10b5:8603 Bridge Device
+ ├─ 0001:02:01.0 10b5:8603 Bridge Device
+ │ └─ 0001:03:00.0 14e4:aa52 Network Controller
+ ├─ 0001:02:02.0 10b5:8603 Bridge Device
+ │ └─ 0001:04:00.0 14e4:aa52 Network Controller
+ ├─ 0001:02:03.0 000d:0000 0x000000
+ ├─ 0001:02:04.0 000d:0000 0x000000
+ ├─ 0001:02:05.0 000d:0000 0x000000
+ ├─ 0001:02:06.0 000d:0000 0x000000
+ ├─ (...)
+ ├─ 0001:02:1d.0 000d:0000 0x000000
+ ├─ 0001:02:1e.0 000d:0000 0x000000
+ └─ 0001:02:1f.0 000d:0000 0x000000
+
+Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
+---
+ arch/arm/boot/dts/bcm4709-netgear-r8000.dts | 48 +++++++++++++++++++++++++++++
+ arch/arm/boot/dts/bcm5301x.dtsi | 8 +++++
+ 2 files changed, 56 insertions(+)
+
+--- a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
++++ b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
+@@ -108,6 +108,54 @@
+ };
+ };
+
++&pcie0 {
++ #address-cells = <3>;
++ #size-cells = <2>;
++
++ bridge@0,0,0 {
++ reg = <0x0000 0 0 0 0>;
++
++ #address-cells = <3>;
++ #size-cells = <2>;
++
++ wifi@0,1,0 {
++ reg = <0x0000 0 0 0 0>;
++ ieee80211-freq-limit = <5735000 5835000>;
++ };
++ };
++};
++
++&pcie1 {
++ #address-cells = <3>;
++ #size-cells = <2>;
++
++ bridge@1,0,0 {
++ reg = <0x0000 0 0 0 0>;
++
++ #address-cells = <3>;
++ #size-cells = <2>;
++
++ bridge@1,1,0 {
++ reg = <0x0000 0 0 0 0>;
++
++ #address-cells = <3>;
++ #size-cells = <2>;
++
++ bridge@1,2,2 {
++ reg = <0x1000 0 0 0 0>;
++
++ #address-cells = <3>;
++ #size-cells = <2>;
++
++ wifi@1,4,0 {
++ reg = <0x0000 0 0 0 0>;
++ ieee80211-freq-limit = <5170000 5730000>;
++ };
++ };
++ };
++ };
++};
++
+ &usb2 {
+ vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
+ };
+--- a/arch/arm/boot/dts/bcm5301x.dtsi
++++ b/arch/arm/boot/dts/bcm5301x.dtsi
+@@ -243,6 +243,14 @@
+ #gpio-cells = <2>;
+ };
+
++ pcie0: pcie@12000 {
++ reg = <0x00012000 0x1000>;
++ };
++
++ pcie1: pcie@13000 {
++ reg = <0x00013000 0x1000>;
++ };
++
+ usb2: usb2@21000 {
+ reg = <0x00021000 0x1000>;
+
--- /dev/null
+From: Dan Haab <dhaab@luxul.com>
+Subject: [PATCH] ARM: BCM5301X: Add DT for Luxul XAP-1410
+
+Luxul XAP-1410 in a dual-band access point device based on BCM47081 with
+serial flash. It has 3 LEDs and just one (reset) button.
+
+Signed-off-by: Dan Haab <dhaab@luxul.com>
+---
+ arch/arm/boot/dts/Makefile | 1 +
+ arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts | 60 +++++++++++++++++++++++++++
+ 2 files changed, 61 insertions(+)
+ create mode 100644 arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts
+
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -73,6 +73,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
+ bcm47081-asus-rt-n18u.dtb \
+ bcm47081-buffalo-wzr-600dhp2.dtb \
+ bcm47081-buffalo-wzr-900dhp.dtb \
++ bcm47081-luxul-xap-1410.dtb \
+ bcm4709-asus-rt-ac87u.dtb \
+ bcm4709-buffalo-wxr-1900dhp.dtb \
+ bcm4709-netgear-r7000.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts
+@@ -0,0 +1,60 @@
++/*
++ * Copyright 2017 Luxul Inc.
++ *
++ * Licensed under the ISC license.
++ */
++
++/dts-v1/;
++
++#include "bcm47081.dtsi"
++
++/ {
++ compatible = "luxul,xap-1410v1", "brcm,bcm47081", "brcm,bcm4708";
++ model = "Luxul XAP-1410 V1";
++
++ chosen {
++ bootargs = "console=ttyS0,115200";
++ };
++
++ memory {
++ reg = <0x00000000 0x08000000>;
++ };
++
++ leds {
++ compatible = "gpio-leds";
++
++ 5ghz {
++ label = "bcm53xx:blue:5ghz";
++ gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "none";
++ };
++
++ 2ghz {
++ label = "bcm53xx:blue:2ghz";
++ gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "none";
++ };
++
++ status {
++ label = "bcm53xx:green:status";
++ gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "timer";
++ };
++ };
++
++ gpio-keys {
++ compatible = "gpio-keys";
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ restart {
++ label = "Reset";
++ linux,code = <KEY_RESTART>;
++ gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
++ };
++ };
++};
++
++&spi_nor {
++ status = "okay";
++};
--- /dev/null
+From: Dan Haab <dhaab@luxul.com>
+Subject: [PATCH] ARM: BCM5301X: Add DT for Luxul XWR-1200
+
+Luxul XWR-1200 in a dual-band router based on BCM47081. It uses serial
+flash (for bootloader and NVRAM) and NAND flash (for firmware).
+
+Signed-off-by: Dan Haab <dhaab@luxul.com>
+---
+ arch/arm/boot/dts/Makefile | 1 +
+ arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts | 107 ++++++++++++++++++++++++++
+ 2 files changed, 108 insertions(+)
+ create mode 100644 arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts
+
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -74,6 +74,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
+ bcm47081-buffalo-wzr-600dhp2.dtb \
+ bcm47081-buffalo-wzr-900dhp.dtb \
+ bcm47081-luxul-xap-1410.dtb \
++ bcm47081-luxul-xwr-1200.dtb \
+ bcm4709-asus-rt-ac87u.dtb \
+ bcm4709-buffalo-wxr-1900dhp.dtb \
+ bcm4709-netgear-r7000.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts
+@@ -0,0 +1,107 @@
++/*
++ * Copyright 2017 Luxul Inc.
++ *
++ * Licensed under the ISC license.
++ */
++
++/dts-v1/;
++
++#include "bcm47081.dtsi"
++#include "bcm5301x-nand-cs0-bch4.dtsi"
++
++/ {
++ compatible = "luxul,xwr-1200v1", "brcm,bcm47081", "brcm,bcm4708";
++ model = "Luxul XWR-1200 V1";
++
++ chosen {
++ bootargs = "console=ttyS0,115200";
++ };
++
++ memory {
++ reg = <0x00000000 0x08000000>;
++ };
++
++ leds {
++ compatible = "gpio-leds";
++
++ power {
++ label = "bcm53xx:green:power";
++ gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "default-on";
++ };
++
++ lan3 {
++ label = "bcm53xx:green:lan3";
++ gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "none";
++ };
++
++ lan4 {
++ label = "bcm53xx:green:lan4";
++ gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "none";
++ };
++
++ wan {
++ label = "bcm53xx:green:wan";
++ gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "none";
++ };
++
++ lan2 {
++ label = "bcm53xx:green:lan2";
++ gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "none";
++ };
++
++ usb {
++ label = "bcm53xx:green:usb";
++ gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "none";
++ };
++
++ status {
++ label = "bcm53xx:green:status";
++ gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "timer";
++ };
++
++ 2ghz {
++ label = "bcm53xx:green:2ghz";
++ gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "none";
++ };
++
++ 5ghz {
++ label = "bcm53xx:green:5ghz";
++ gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "none";
++ };
++
++ lan1 {
++ label = "bcm53xx:green:lan1";
++ gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "none";
++ };
++ };
++
++ gpio-keys {
++ compatible = "gpio-keys";
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ restart {
++ label = "Reset";
++ linux,code = <KEY_RESTART>;
++ gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
++ };
++ };
++};
++
++&usb2 {
++ vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
++};
++
++&spi_nor {
++ status = "okay";
++};
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -76,6 +76,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
+@@ -78,6 +78,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
bcm4709-asus-rt-ac87u.dtb \
bcm4709-buffalo-wxr-1900dhp.dtb \
bcm4709-netgear-r7000.dtb \
projects / openwrt / staging / blogic.git / commitdiff