ipq40xx: add support for Plasma Cloud PA1200
authorMarek Lindner <marek.lindner@kaiwoo.ai>
Sun, 25 Nov 2018 13:46:54 +0000 (21:46 +0800)
committerPetr Štetiar <ynezz@true.cz>
Tue, 22 Dec 2020 18:11:50 +0000 (19:11 +0100)
Device specifications:

* QCA IPQ4018
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200
* 2T2R 5 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200
* 3x GPIO-LEDs for status (cyan, purple, yellow)
* 1x GPIO-button (reset)
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
  - phy@mdio4:
    + Label: Ethernet 1
    + gmac0 (ethaddr) in original firmware
    + used as LAN interface
  - phy@mdio3:
    + Label: Ethernet 2
    + gmac1 (eth1addr) in original firmware
    + 802.3af/at POE(+)
    + used as WAN interface
* 12V/24V 1A DC

Flashing instructions:

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
package/boot/uboot-envtools/files/ipq40xx
package/firmware/ipq-wifi/Makefile
package/firmware/ipq-wifi/board-plasmacloud_pa1200.ipq4019 [new file with mode: 0644]
scripts/om-fwupgradecfg-gen.sh
target/linux/ipq40xx/base-files/etc/board.d/02_network
target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh
target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-pa1200.dts [new file with mode: 0644]
target/linux/ipq40xx/image/Makefile
target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch

index 27aab6b2865e148a9e1e2c7b34bd4a6903130170..9252c0ffac6abe6be5f72aa550229a6318742a6e 100644 (file)
@@ -36,7 +36,8 @@ edgecore,ecw5211 |\
 glinet,gl-b1300 |\
 luma,wrtq-329acn |\
 openmesh,a42 |\
-openmesh,a62)
+openmesh,a62 |\
+plasmacloud,pa1200)
        ubootenv_add_uci_config "/dev/mtd5" "0x0" "0x10000" "0x10000"
        ;;
 buffalo,wtr-m2133hp)
index 9aa6852046a20435c88047d5fc6f7bf445976f2d..e26269a71026f084b834f1f86098462cb63c2d65 100644 (file)
@@ -42,6 +42,7 @@ ALLWIFIBOARDS:= \
        linksys_mr8300-v0 \
        luma_wrtq-329acn \
        mobipromo_cm520-79f \
+       plasmacloud_pa1200 \
        qxwlan_e2600ac
 
 ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
@@ -120,6 +121,7 @@ $(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
 $(eval $(call generate-ipq-wifi-package,linksys_mr8300-v0,Linksys MR8300))
 $(eval $(call generate-ipq-wifi-package,luma_wrtq-329acn,Luma WRTQ-329ACN))
 $(eval $(call generate-ipq-wifi-package,mobipromo_cm520-79f,MobiPromo CM520-79F))
+$(eval $(call generate-ipq-wifi-package,plasmacloud_pa1200,Plasma Cloud PA1200))
 $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC))
 
 $(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))
diff --git a/package/firmware/ipq-wifi/board-plasmacloud_pa1200.ipq4019 b/package/firmware/ipq-wifi/board-plasmacloud_pa1200.ipq4019
new file mode 100644 (file)
index 0000000..99d6df8
Binary files /dev/null and b/package/firmware/ipq-wifi/board-plasmacloud_pa1200.ipq4019 differ
index 98464c631bbe4154137e4629c1a9890b6cd8bc55..c5dcfb001899c067650189f58af81dd4efba7056 100755 (executable)
@@ -7,7 +7,7 @@
 #
 
 usage() {
-       echo "Usage: $0 <OM2P|OM5P|OM5PAC|MR600|MR900|MR1750|A60|A42|A62|PA300> <out file path> <kernel path> <rootfs path>"
+       echo "Usage: $0 <OM2P|OM5P|OM5PAC|MR600|MR900|MR1750|A60|A42|A62|PA300|PA1200> <out file path> <kernel path> <rootfs path>"
        rm -f $CFG_OUT
        exit 1
 }
@@ -33,7 +33,7 @@ case $CE_TYPE in
                SIZE_FACTOR=1
                SIZE_FORMAT="%d"
                ;;
-       A42)
+       A42|PA1200)
                MAX_PART_SIZE=15616
                KERNEL_FLASH_ADDR=0x180000
                SIZE_FACTOR=1024
index 86787eeffd9cc34fa57904c1f4bbf48a5ece5231..b9e79c3b68db7531ca0340699bc15670f465b7c2 100755 (executable)
@@ -17,7 +17,8 @@ ipq40xx_setup_interfaces()
        alfa-network,ap120c-ac|\
        engenius,emr3500|\
        engenius,ens620ext|\
-       luma,wrtq-329acn)
+       luma,wrtq-329acn|\
+       plasmacloud,pa1200)
                ucidef_set_interfaces_lan_wan "eth0" "eth1"
                ;;
        aruba,ap-303|\
index f33d3f331c14ddf4c7e99d731e583d79bd7d2d43..ade0d7434117c010f3ab603bf1dbdae1ff120337 100644 (file)
@@ -101,6 +101,7 @@ case "$FIRMWARE" in
        luma,wrtq-329acn|\
        openmesh,a42 |\
        openmesh,a62 |\
+       plasmacloud,pa1200 |\
        qxwlan,e2600ac-c1 |\
        qxwlan,e2600ac-c2 |\
        unielec,u4019-32m)
@@ -198,6 +199,7 @@ case "$FIRMWARE" in
        luma,wrtq-329acn|\
        openmesh,a42 |\
        openmesh,a62 |\
+       plasmacloud,pa1200 |\
        qxwlan,e2600ac-c1 |\
        qxwlan,e2600ac-c2 |\
        unielec,u4019-32m)
index 807a85d43ccd57642b52e7c1a7f92295cb6cd036..60886071c9748407746ca9adfab52a1da9e524f2 100644 (file)
@@ -44,6 +44,7 @@ platform_do_upgrade_dualboot_datachk() {
        # boot anymore to Linux until it was reflashed with ap51-flash.
        local next_boot_part="1"
        case "$(board_name)" in
+       plasmacloud,pa1200|\
        openmesh,a42)
                primary_kernel_mtd=8
                ;;
index 0fbce92f3bedf3f6bac43aafecdc2ef92f7d0644..22e9ffe1145077a785918aa41514bc666d749d6d 100644 (file)
@@ -111,7 +111,8 @@ platform_do_upgrade() {
                nand_do_upgrade "$1"
                ;;
        openmesh,a42 |\
-       openmesh,a62)
+       openmesh,a62 |\
+       plasmacloud,pa1200)
                PART_NAME="inactive"
                platform_do_upgrade_dualboot_datachk "$1"
                ;;
diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-pa1200.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-pa1200.dts
new file mode 100644 (file)
index 0000000..bcb9552
--- /dev/null
@@ -0,0 +1,197 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2017-2020, Sven Eckelmann <sven@narfation.org>
+ * Copyright (c) 2018, Marek Lindner <marek.lindner@kaiwoo.ai>
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+       model = "Plasma Cloud PA1200";
+       compatible = "plasmacloud,pa1200";
+
+       soc {
+               rng@22000 {
+                       status = "okay";
+               };
+
+               mdio@90000 {
+                       status = "okay";
+               };
+
+               ess-psgmii@98000 {
+                       status = "okay";
+               };
+
+               tcsr@194b000 {
+                       /* select hostmode */
+                       compatible = "qcom,tcsr";
+                       reg = <0x194b000 0x100>;
+                       qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+                       status = "okay";
+               };
+
+               tcsr@1949000 {
+                       compatible = "qcom,tcsr";
+                       reg = <0x1949000 0x100>;
+                       qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+               };
+
+               ess_tcsr@1953000 {
+                       compatible = "qcom,tcsr";
+                       reg = <0x1953000 0x1000>;
+                       qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+               };
+
+               tcsr@1957000 {
+                       compatible = "qcom,tcsr";
+                       reg = <0x1957000 0x100>;
+                       qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+               };
+
+               usb2: usb2@60f8800 {
+                       status = "okay";
+               };
+
+               crypto@8e3a000 {
+                       status = "okay";
+               };
+
+               watchdog@b017000 {
+                       status = "okay";
+               };
+
+               ess-switch@c000000 {
+                       status = "okay";
+               };
+
+               edma@c080000 {
+                       status = "okay";
+               };
+       };
+
+       keys {
+               compatible = "gpio-keys";
+
+               reset {
+                       label = "reset";
+                       gpios = <&tlmm 59 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RESTART>;
+               };
+       };
+
+       aliases {
+               led-boot = &led_status_purple;
+               led-failsafe = &led_status_yellow;
+               led-running = &led_status_cyan;
+               led-upgrade = &led_status_yellow;
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               led_status_cyan: status_cyan {
+                       label = "cyan:status";
+                       gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+               };
+
+               led_status_purple: status_purple {
+                       label = "purple:status";
+                       gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
+               };
+
+               led_status_yellow: status_yellow {
+                       label = "yellow:status";
+                       gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+               };
+       };
+
+};
+
+&tlmm {
+       serial_pins: serial_pinmux {
+               mux {
+                       pins = "gpio60", "gpio61";
+                       function = "blsp_uart0";
+                       bias-disable;
+               };
+       };
+
+       spi_0_pins: spi_0_pinmux {
+               pin {
+                       function = "blsp_spi0";
+                       pins = "gpio55", "gpio56", "gpio57";
+                       drive-strength = <12>;
+                       bias-disable;
+               };
+               pin_cs {
+                       function = "gpio";
+                       pins = "gpio54";
+                       drive-strength = <2>;
+                       bias-disable;
+                       output-high;
+               };
+       };
+};
+
+&blsp_dma {
+       status = "okay";
+};
+
+&blsp1_spi1 {
+       pinctrl-0 = <&spi_0_pins>;
+       pinctrl-names = "default";
+       status = "okay";
+       cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+       flash@0 {
+               #address-cells = <1>;
+               #size-cells = <1>;
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <24000000>;
+               /* partitions are passed via bootloader */
+       };
+};
+
+&blsp1_uart1 {
+       pinctrl-0 = <&serial_pins>;
+       pinctrl-names = "default";
+       status = "okay";
+};
+
+&cryptobam {
+       status = "okay";
+};
+
+&gmac0 {
+       qcom,phy_mdio_addr = <4>;
+       qcom,poll_required = <1>;
+       qcom,forced_speed = <1000>;
+       qcom,forced_duplex = <1>;
+       vlan_tag = <2 0x20>;
+};
+
+&gmac1 {
+       qcom,phy_mdio_addr = <3>;
+       qcom,poll_required = <1>;
+       qcom,forced_speed = <1000>;
+       qcom,forced_duplex = <1>;
+       vlan_tag = <1 0x10>;
+};
+
+&usb2_hs_phy {
+       status = "okay";
+};
+
+&wifi0 {
+       status = "okay";
+       qcom,ath10k-calibration-variant = "PlasmaCloud-PA1200";
+};
+
+&wifi1 {
+       status = "okay";
+       qcom,ath10k-calibration-variant = "PlasmaCloud-PA1200";
+};
index b3f2d1f755f61ac176dddfad785d59eee09d6c61..b0fde22813010c866dad7995eb6587532e2d8f8b 100644 (file)
@@ -648,6 +648,22 @@ define Device/openmesh_a62
 endef
 TARGET_DEVICES += openmesh_a62
 
+define Device/plasmacloud_pa1200
+       $(call Device/FitImageLzma)
+       DEVICE_VENDOR := Plasma Cloud
+       DEVICE_MODEL := PA1200
+       SOC := qcom-ipq4018
+       DEVICE_DTS_CONFIG := config@pc.pa1200
+       BLOCKSIZE := 64k
+       KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
+       IMAGE_SIZE := 15616k
+       IMAGES += factory.bin
+       IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA1200
+       IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
+       DEVICE_PACKAGES := uboot-envtools ipq-wifi-plasmacloud-pa1200
+endef
+TARGET_DEVICES += plasmacloud_pa1200
+
 define Device/qcom_ap-dk01.1-c1
        DEVICE_VENDOR := Qualcomm Atheros
        DEVICE_MODEL := AP-DK01.1
index 06dd135a59a6dac185cb5b56a7caad035ea70de2..8d725ebf9eb21eff474cf1918629b2ec972e4581 100644 (file)
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -837,11 +837,54 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -837,11 +837,55 @@ dtb-$(CONFIG_ARCH_QCOM) += \
        qcom-apq8074-dragonboard.dtb \
        qcom-apq8084-ifc6540.dtb \
        qcom-apq8084-mtp.dtb \
@@ -31,6 +31,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 +      qcom-ipq4018-meshpoint-one.dtb \
 +      qcom-ipq4018-nbg6617.dtb \
 +      qcom-ipq4019-oap100.dtb \
++      qcom-ipq4018-pa1200.dtb \
 +      qcom-ipq4018-rt-ac58u.dtb \
 +      qcom-ipq4018-wre6606.dtb \
 +      qcom-ipq4018-wrtq-329acn.dtb \