ramips: add support for Youku YK1

Changes since V1:
I resend this patch for current trunk.The former V1 patch is for CC branch.

Signed-off-by: Shonn Lu <countrysideboy@qq.com>
SVN-Revision: 47617

diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index 5627c8ca8cc52998930a439f95556a8b8a527c30..1c18ded505e2f65ed5c304ac99bdb85dac75eb8a 100755 (executable)
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -268,6 +268,11 @@ zbt-wr8305rt)
 zte-q7)
        set_wifi_led "$board:blue:status"
        ;;
+youku-yk1)
+       ucidef_set_led_default "power" "power" "$board:blue:power" "1"
+       set_wifi_led "$board:blue:air"
+       set_usb_led "$board:blue:usb"
+       ;;
 esac
 
 board_config_flush

diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index 382174298a57ef4d3b959a429bb833c5d7c10f8d..22809d1720ae3ff374a724c99fdf06557e101ce6 100755 (executable)
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -84,7 +84,8 @@ ramips_setup_interfaces()
        wsr-600|\
        wt1520|\
        y1|\
-       zbt-wg2626)
+       zbt-wg2626|\
+       youku-yk1)
                ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
                ucidef_add_switch "switch0" "1" "1"
                ucidef_add_switch_vlan "switch0" "1" "0 1 2 3 6t"

diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index a1bcb7261d5a08717235380c66a081b99a87843d..d6fdeb9891bd5a3184785fc06dfbc3598f937c16 100755 (executable)
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -460,6 +460,9 @@ ramips_board_detect() {
        *"ZBT-WR8305RT")
                name="zbt-wr8305rt"
                ;;
+       *"YK1")
+               name="youku-yk1"
+               ;;
        *)
                name="generic"
                ;;

diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index 0e8d619069b7e5d037f400ec6948819f4ecc6178..0b9dd43791c1f0a364e470ae5cf341914e4e791a 100755 (executable)
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -134,7 +134,8 @@ platform_check_image() {
        zbt-wa05|\
        zbt-wg2626|\
        zbt-wr8305rt|\
-       zte-q7)
+       zte-q7|\
+       youku-yk1)
                [ "$magic" != "27051956" ] && {
                        echo "Invalid image type."
                        return 1

diff --git a/target/linux/ramips/dts/YOUKU-YK1.dts b/target/linux/ramips/dts/YOUKU-YK1.dts
new file mode 100644 (file)
index 0000000..418351c
--- /dev/null
+++ b/target/linux/ramips/dts/YOUKU-YK1.dts
@@ -0,0 +1,127 @@
+/dts-v1/;
+
+/include/ "mt7620a.dtsi"
+
+/ {
+       compatible = "YOUKU-YK1", "ralink,mt7620a-soc";
+       model = "YOUKU YK1";
+
+       palmbus@10000000 {
+
+               gpio0: gpio@600 {
+                       status = "okay";
+               };
+
+               gpio1: gpio@638 {
+                       status = "okay";
+               };
+
+               gpio2: gpio@660 {
+                       status = "okay";
+               };
+
+               gpio3: gpio@688 {
+                       status = "okay";
+               };
+
+               spi@b00 {
+                       status = "okay";
+
+                       m25p80@0 {
+                               #address-cells = <1>;
+                               #size-cells = <1>;
+                               compatible = "w25q256";
+                               reg = <0 0>;
+                               linux,modalias = "m25p80", "w25q256";
+                               spi-max-frequency = <10000000>;
+
+                               partition@0 {
+                                       label = "u-boot";
+                                       reg = <0x0 0x30000>;
+                                       read-only;
+                               };
+
+                               partition@30000 {
+                                       label = "u-boot-env";
+                                       reg = <0x30000 0x10000>;
+                                       read-only;
+                               };
+
+                               factory: partition@40000 {
+                                       label = "factory";
+                                       reg = <0x40000 0x10000>;
+                                       read-only;
+                               };
+
+                               partition@50000 {
+                                       label = "firmware";
+                                       reg = <0x50000 0x1fb0000>;
+                               };
+                       };
+               };
+       };
+
+       pinctrl {
+               state_default: pinctrl0 {
+                       default {
+                               ralink,group = "i2c", "uartf", "rgmii1", "rgmii2", "ephy", "wled", "nd_sd";
+                               ralink,function = "gpio";
+                       };
+               };
+       };
+
+       ethernet@10100000 {
+               pinctrl-names = "default";
+               pinctrl-0 = <&ephy_pins>;
+               mtd-mac-address = <&factory 0x4>;
+               ralink,port-map = "llllw";
+       };
+
+       wmac@10180000 {
+               ralink,mtd-eeprom = <&factory 0>;
+       };
+
+       sdhci@b0130000 {
+               status = "okay";
+       };
+
+       ehci@101c0000 {
+               status = "okay";
+       };
+
+       ohci@101c1000 {
+               status = "okay";
+       };
+
+       gpio-leds {
+               compatible = "gpio-leds";
+               wan {
+                       label = "youku-yk1:blue:wan";
+                       gpios = <&gpio2 4 1>;
+               };
+               air {
+                       label = "youku-yk1:blue:air";
+                       gpios = <&gpio3 0 1>;
+               };
+               usb {
+                       label = "youku-yk1:blue:usb";
+                       gpios = <&gpio1 11 1>;
+               };
+               power {
+                       label = "youku-yk1:blue:power";
+                       gpios = <&gpio1 5 1>;
+               };
+       };
+
+       gpio-keys-polled {
+               compatible = "gpio-keys-polled";
+               #address-cells = <1>;
+               #size-cells = <0>;
+               poll-interval = <20>;
+               reset {
+                       label = "reset";
+                       gpios = <&gpio0 1 1>;
+                       linux,code = <0x198>;
+               };
+       };
+};

diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile
index 5e19c3f97d22a683e4cd7d20dca2bbf39c7b29ef..5a2b98cac6aff23ca668a5f4259c7c456ad9a7f5 100644 (file)
--- a/target/linux/ramips/image/Makefile
+++ b/target/linux/ramips/image/Makefile
@@ -900,6 +900,7 @@ Image/Build/Profile/WRTNODE=$(call BuildFirmware/Default16M/$(1),$(1),wrtnode,WR
 Image/Build/Profile/WT3020=$(call BuildFirmware/PorayDualSize/$(1),$(1),wt3020,WT3020)
 Image/Build/Profile/MIWIFI-MINI=$(call BuildFirmware/Default16M/$(1),$(1),miwifi-mini,MIWIFI-MINI)
 Image/Build/Profile/ZTE-Q7=$(call BuildFirmware/Default8M/$(1),$(1),zte-q7,ZTE-Q7)
+Image/Build/Profile/YOUKU-YK1=$(call BuildFirmware/Default16M/$(1),$(1),youku-yk1,YOUKU-YK1)
 Image/Build/Profile/ZBT-WA05=$(call BuildFirmware/Default8M/$(1),$(1),zbt-wa05,ZBT-WA05)
 Image/Build/Profile/ZBT-WR8305RT=$(call BuildFirmware/Default8M/$(1),$(1),zbt-wr8305rt,ZBT-WR8305RT)
 Image/Build/Profile/ArcherC20i=$(call BuildFirmware/Tplink/$(1),$(1),ArcherC20i,ArcherC20i)
@@ -939,6 +940,7 @@ define Image/Build/Profile/Default
        $(call Image/Build/Profile/WT3020,$(1))
        $(call Image/Build/Profile/MIWIFI-MINI,$(1))
        $(call Image/Build/Profile/ZTE-Q7,$(1))
+       $(call Image/Build/Profile/YOUKU-YK1,$(1))
        $(call Image/Build/Profile/ZBT-WA05,$(1))
        $(call Image/Build/Profile/ZBT-WR8305RT,$(1))
        $(call Image/Build/Profile/ArcherC20i,$(1))