mmc: mmci: add edge support to data and command out in variant data.

This patch adds edge support for data and command out to variant structure
giving more flexibility to the driver to support more SOCs which have
different clock register layout.

Without this patch other new SOCs like Qcom will have to add more code to
special case them

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 2fb893313044b2d22b31ba46be5e5664783cff71..5228c5de334d9ca9c300fe83bd636b8ce41b2a6f 100644 (file)
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -53,6 +53,7 @@ static unsigned int fmax = 515633;
  * @clkreg: default value for MCICLOCK register
  * @clkreg_enable: enable value for MMCICLOCK register
  * @clkreg_8bit_bus_enable: enable value for 8 bit bus
+ * @clkreg_neg_edge_enable: enable value for inverted data/cmd output
  * @datalength_bits: number of bits in the MMCIDATALENGTH register
  * @fifosize: number of bytes that can be written when MMCI_TXFIFOEMPTY
  *           is asserted (likewise for RX)
@@ -74,6 +75,7 @@ struct variant_data {
        unsigned int            clkreg;
        unsigned int            clkreg_enable;
        unsigned int            clkreg_8bit_bus_enable;
+       unsigned int            clkreg_neg_edge_enable;
        unsigned int            datalength_bits;
        unsigned int            fifosize;
        unsigned int            fifohalfsize;
@@ -143,6 +145,7 @@ static struct variant_data variant_ux500 = {
        .clkreg                 = MCI_CLK_ENABLE,
        .clkreg_enable          = MCI_ST_UX500_HWFCEN,
        .clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS,
+       .clkreg_neg_edge_enable = MCI_ST_UX500_NEG_EDGE,
        .datalength_bits        = 24,
        .sdio                   = true,
        .st_clkdiv              = true,
@@ -159,6 +162,7 @@ static struct variant_data variant_ux500v2 = {
        .clkreg                 = MCI_CLK_ENABLE,
        .clkreg_enable          = MCI_ST_UX500_HWFCEN,
        .clkreg_8bit_bus_enable = MCI_ST_8BIT_BUS,
+       .clkreg_neg_edge_enable = MCI_ST_UX500_NEG_EDGE,
        .datactrl_mask_ddrmode  = MCI_ST_DPSM_DDRMODE,
        .datalength_bits        = 24,
        .sdio                   = true,
@@ -314,7 +318,7 @@ static void mmci_set_clkreg(struct mmci_host *host, unsigned int desired)
 
        if (host->mmc->ios.timing == MMC_TIMING_UHS_DDR50 ||
            host->mmc->ios.timing == MMC_TIMING_MMC_DDR52)
-               clk |= MCI_ST_UX500_NEG_EDGE;
+               clk |= variant->clkreg_neg_edge_enable;
 
        mmci_write_clkreg(host, clk);
 }