dt-bindings: drm/bridge: Document sn65dsi86 bridge bindings

Document the bindings used for the sn65dsi86 DSI to eDP bridge.

Changes in v1:
 - Rephrase the dt-binding descriptions to be more inline with existing
   bindings (Andrzej Hajda).
 - Add missing dt-binding that are parsed by corresponding driver
   (Andrzej Hajda).

Changes in v2:
 - Remove edp panel specific dt-binding entries. Only keep bridge
   specific entries (Sean Paul).
 - Remove custom-modes dt entry since its usage is removed from driver also (Sean Paul).
 - Remove is-pluggable dt entry since this will not be needed anymore (Sean Paul).

Changes in v3:
 - Remove irq-gpio dt entry and instead populate is an interrupt
   property (Rob Herring).

Changes in v4:
 - Add link to bridge chip datasheet (Stephen Boyd)
 - Add vpll and vcc regulator supply bindings (Stephen Boyd)
 - Add ref clk optional dt binding (Stephen Boyd)
 - Add gpio-controller optional dt binding (Stephen Boyd)

Changes in v5:
 - Use clock property to specify the input refclk (Stephen Boyd).
 - Update gpio cell and pwm cell numbers (Stephen Boyd).

Changes in v6:
 - Add property to mention the lane mapping scheme and polarity inversion
   (Stephen Boyd).

Changes in v7:
 - Detail description of lane mapping scheme dt property (Andrzej
   Hajda/ Rob Herring).
 - Removed HDP gpio binding, since the bridge uses IRQ signal to
   determine HPD, and IRQ property is already documented in binding.

Changes in v8:
 - Removed unnecessary explanation of lane mapping and polarity dt
   property, since these are already explained in media/video-interface
   dt binidng (Rob Herring).

Changes in v9:
 - Avoid putting re-definition of lane mapping and polarity dt binding
   (Rob Herring).

Changes in v10:
 - Use interrupts-extended property instead of interrupts to specify
   interrupt line (Andrzej Hajda).
 - Move data-lanes and lane-polarity property example to proper place (Andrzej Hajda).

Changes in v11:
 - Add a property for suspend gpio function of GPIO1 pin on bridge chip
   (Stephen Boyd).

Changes in v12:
 - Remove binding for dedicated DDC line (Andrzej Hajda).

Signed-off-by: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180716084330.26698-3-spanda@codeaurora.org

diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
new file mode 100644 (file)
index 0000000..0a3fbb5
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
@@ -0,0 +1,87 @@
+SN65DSI86 DSI to eDP bridge chip
+--------------------------------
+
+This is the binding for Texas Instruments SN65DSI86 bridge.
+http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf
+
+Required properties:
+- compatible: Must be "ti,sn65dsi86"
+- reg: i2c address of the chip, 0x2d as per datasheet
+- enable-gpios: gpio specification for bridge_en pin (active high)
+
+- vccio-supply: A 1.8V supply that powers up the digital IOs.
+- vpll-supply: A 1.8V supply that powers up the displayport PLL.
+- vcca-supply: A 1.2V supply that powers up the analog circuits.
+- vcc-supply: A 1.2V supply that powers up the digital core.
+
+Optional properties:
+- interrupts-extended: Specifier for the SN65DSI86 interrupt line.
+
+- gpio-controller: Marks the device has a GPIO controller.
+- #gpio-cells    : Should be two. The first cell is the pin number and
+                   the second cell is used to specify flags.
+                   See ../../gpio/gpio.txt for more information.
+- #pwm-cells : Should be one. See ../../pwm/pwm.txt for description of
+               the cell formats.
+
+- clock-names: should be "refclk"
+- clocks: Specification for input reference clock. The reference
+         clock rate must be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz.
+
+- data-lanes: See ../../media/video-interface.txt
+- lane-polarities: See ../../media/video-interface.txt
+
+- suspend-gpios: specification for GPIO1 pin on bridge (active low)
+
+Required nodes:
+This device has two video ports. Their connections are modelled using the
+OF graph bindings specified in Documentation/devicetree/bindings/graph.txt.
+
+- Video port 0 for DSI input
+- Video port 1 for eDP output
+
+Example
+-------
+
+edp-bridge@2d {
+       compatible = "ti,sn65dsi86";
+       #address-cells = <1>;
+       #size-cells = <0>;
+       reg = <0x2d>;
+
+       enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>;
+       suspend-gpios = <&msmgpio 34 GPIO_ACTIVE_LOW>;
+
+       interrupts-extended = <&gpio3 4 IRQ_TYPE_EDGE_FALLING>;
+
+       vccio-supply = <&pm8916_l17>;
+       vcca-supply = <&pm8916_l6>;
+       vpll-supply = <&pm8916_l17>;
+       vcc-supply = <&pm8916_l6>;
+
+       clock-names = "refclk";
+       clocks = <&input_refclk>;
+
+       ports {
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               port@0 {
+                       reg = <0>;
+
+                       edp_bridge_in: endpoint {
+                               remote-endpoint = <&dsi_out>;
+                       };
+               };
+
+               port@1 {
+                       reg = <1>;
+
+                       edp_bridge_out: endpoint {
+                               data-lanes = <2 1 3 0>;
+                               lane-polarities = <0 1 0 1>;
+                               remote-endpoint = <&edp_panel_in>;
+                       };
+               };
+       };
+}