+++ /dev/null
-/*
- * Copyright (C) 2008 Miromico AG
- *
- * Mostly copied form atmel ATNGW100 sources
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-
-#include <asm/io.h>
-#include <asm/sdram.h>
-#include <asm/arch/clk.h>
-#include <asm/arch/hmatrix.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/mmu.h>
-#include <asm/arch/portmux.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-struct mmu_vm_range mmu_vmr_table[CONFIG_SYS_NR_VM_REGIONS] = {
- {
- .virt_pgno = CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT,
- .nr_pages = CONFIG_SYS_FLASH_SIZE >> MMU_PAGE_SHIFT,
- .phys = (CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT)
- | MMU_VMR_CACHE_NONE,
- }, {
- .virt_pgno = CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT,
- .nr_pages = EBI_SDRAM_SIZE >> MMU_PAGE_SHIFT,
- .phys = (CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT)
- | MMU_VMR_CACHE_WRBACK,
- },
-};
-
-static const struct sdram_config sdram_config = {
- .data_bits = SDRAM_DATA_32BIT,
- .row_bits = 13,
- .col_bits = 9,
- .bank_bits = 2,
- .cas = 3,
- .twr = 2,
- .trc = 7,
- .trp = 2,
- .trcd = 2,
- .tras = 5,
- .txsr = 5,
- /* 7.81 us */
- .refresh_period = (781 * (SDRAMC_BUS_HZ / 1000)) / 100000,
-};
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
- return macb_eth_initialize(0, (void *)ATMEL_BASE_MACB0,
- bis->bi_phy_id[0]);
-}
-#endif
-
-int board_early_init_f(void)
-{
- /* Enable SDRAM in the EBI mux */
- hmatrix_slave_write(EBI, SFR, HMATRIX_BIT(EBI_SDRAM_ENABLE));
-
- portmux_enable_ebi(32, 23, 0, PORTMUX_DRIVE_HIGH);
- sdram_init(uncached(EBI_SDRAM_BASE), &sdram_config);
-
- portmux_enable_usart1(PORTMUX_DRIVE_MIN);
-
-#if defined(CONFIG_MACB)
- portmux_enable_macb0(PORTMUX_MACB_MII, PORTMUX_DRIVE_HIGH);
-#endif
-#if defined(CONFIG_MMC)
- portmux_enable_mmci(0, PORTMUX_MMCI_4BIT, PORTMUX_DRIVE_LOW);
-#endif
- return 0;
-}
-
-int board_early_init_r(void)
-{
- gd->bd->bi_phy_id[0] = 0x01;
- return 0;
-}
-
-int board_postclk_init(void)
-{
- /* Hammerhead boards uses GCLK3 as 25MHz output to ethernet PHY */
- gclk_enable_output(3, PORTMUX_DRIVE_LOW);
- gclk_set_rate(3, GCLK_PARENT_OSC0, 25000000);
- return 0;
-}
+++ /dev/null
-/*
- * Copyright (C) 2008 Miromico AG
- *
- * Configuration settings for the Miromico Hammerhead AVR32 board
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_AT32AP
-#define CONFIG_AT32AP7000
-#define CONFIG_HAMMERHEAD
-
-/*
- * Set up the PLL to run at 125 MHz, the CPU to run at the PLL
- * frequency, the HSB and PBB busses to run at 1/2 the PLL frequency
- * and the PBA bus to run at 1/4 the PLL frequency.
- */
-#define CONFIG_PLL
-#define CONFIG_SYS_POWER_MANAGER
-#define CONFIG_SYS_OSC0_HZ 25000000
-#define CONFIG_SYS_PLL0_DIV 1
-#define CONFIG_SYS_PLL0_MUL 5
-#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES 16
-#define CONFIG_SYS_CLKDIV_CPU 0
-#define CONFIG_SYS_CLKDIV_HSB 1
-#define CONFIG_SYS_CLKDIV_PBA 2
-#define CONFIG_SYS_CLKDIV_PBB 1
-
-/* Reserve VM regions for SDRAM and NOR flash */
-#define CONFIG_SYS_NR_VM_REGIONS 2
-
-/*
- * The PLLOPT register controls the PLL like this:
- * icp = PLLOPT<2>
- * ivco = PLLOPT<1:0>
- *
- * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz).
- */
-#define CONFIG_SYS_PLL0_OPT 0x04
-
-#define CONFIG_USART_BASE ATMEL_BASE_USART1
-#define CONFIG_USART_ID 1
-
-#define CONFIG_HOSTNAME hammerhead
-
-/* User serviceable stuff */
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
-#define CONFIG_STACKSIZE (2048)
-
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_BOOTARGS \
- "console=ttyS0 root=mtd1 rootfstype=jffs2"
-#define CONFIG_BOOTCOMMAND \
- "fsload; bootm"
-
-#define CONFIG_BOOTDELAY 1
-
-/*
- * After booting the board for the first time, new ethernet address
- * should be generated and assigned to the environment variables
- * "ethaddr". This is normally done during production.
- */
-#define CONFIG_OVERWRITE_ETHADDR_ONCE
-
-/*
- * BOOTP/DHCP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MMC
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_SETGETDCR
-
-#define CONFIG_ATMEL_USART
-#define CONFIG_MACB
-#define CONFIG_PORTMUX_PIO
-#define CONFIG_SYS_NR_PIOS 5
-#define CONFIG_SYS_HSDRAMC
-#define CONFIG_MMC
-#define CONFIG_GENERIC_ATMEL_MCI
-#define CONFIG_GENERIC_MMC
-
-#define CONFIG_SYS_DCACHE_LINESZ 32
-#define CONFIG_SYS_ICACHE_LINESZ 32
-
-#define CONFIG_NR_DRAM_BANKS 1
-
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-
-#define CONFIG_SYS_FLASH_BASE 0x00000000
-#define CONFIG_SYS_FLASH_SIZE 0x800000
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
-#define CONFIG_SYS_MAX_FLASH_SECT 135
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_TEXT_BASE 0x00000000
-
-#define CONFIG_SYS_INTRAM_BASE 0x24000000
-#define CONFIG_SYS_INTRAM_SIZE 0x8000
-
-#define CONFIG_SYS_SDRAM_BASE 0x10000000
-
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SIZE 65536
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE)
-
-#define CONFIG_SYS_MALLOC_LEN (256*1024)
-
-
-/* Allow 4MB for the kernel run-time image */
-#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x00400000)
-#define CONFIG_SYS_BOOTPARAMS_LEN (16 * 1024)
-
-/* Other configuration settings that shouldn't have to change all that often */
-#define CONFIG_SYS_PROMPT "Hammerhead> "
-#define CONFIG_SYS_CBSIZE 256
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP
-
-#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x1f00000)
-
-#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 }
-
-#endif /* __CONFIG_H */
projects / project / bcm63xx / u-boot.git / commitdiff