ath79: add support for TP-Link CPE610-v1

TP-Link CPE610-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344

Specifications:
 - Based on the same underlying hardware as the TP-Link CPE510
 - Power, LAN, WLAN5G green LEDs
 - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector

Flashing instructions:
 Flash factory image through stock firmware WEB UI
 or through TFTP
 To get to TFTP recovery just hold reset button while powering on for
 around 4-5 seconds and release.
 Rename factory image to recovery.bin
 Stock TFTP server IP:192.168.0.100
 Stock device TFTP adress:192.168.0.254

Signed-off-by: Andrew Cameron <apcameron@softhome.net>

diff --git a/target/linux/ath79/base-files/etc/board.d/01_leds b/target/linux/ath79/base-files/etc/board.d/01_leds
index 41a4abae18c9ea94c945eba6ff312c3deada2237..46b3e51193600d50cc9acc14a53cb7bf5d23a56a 100755 (executable)
--- a/target/linux/ath79/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/base-files/etc/board.d/01_leds
@@ -155,6 +155,9 @@ tplink,cpe210-v3)
        ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "tp-link:green:link3" "wlan0" "60" "100"
        ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "tp-link:green:link4" "wlan0" "80" "100"
        ;;
+tplink,cpe610-v1)
+       ucidef_set_led_netdev "lan" "LAN" "tp-link:green:lan" "eth0"
+       ;;
 tplink,re450-v2)
        ucidef_set_led_netdev "lan_data" "LAN Data" "tp-link:green:lan_data" "eth0" "tx rx"
        ucidef_set_led_netdev "lan_link" "LAN Link" "tp-link:green:lan_link" "eth0" "link"

diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
index 84c83ff01ede61bdbab492295479a514cd55d5ba..fffb00eca0828cea76fb81834f05336075633793 100755 (executable)
--- a/target/linux/ath79/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/base-files/etc/board.d/02_network
@@ -25,6 +25,7 @@ ath79_setup_interfaces()
        pqi,air-pen|\
        tplink,cpe210-v2|\
        tplink,cpe210-v3|\
+       tplink,cpe610-v1|\
        tplink,re350k-v1|\
        tplink,re450-v2|\
        tplink,tl-mr10u|\

diff --git a/target/linux/ath79/dts/ar9344_tplink_cpe610-v1.dts b/target/linux/ath79/dts/ar9344_tplink_cpe610-v1.dts
new file mode 100644 (file)
index 0000000..5b7c32c
--- /dev/null
+++ b/target/linux/ath79/dts/ar9344_tplink_cpe610-v1.dts
@@ -0,0 +1,140 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar9344.dtsi"
+
+/ {
+       model = "TP-Link CPE610 v1";
+       compatible = "tplink,cpe610-v1", "qca,ar9344";
+
+       aliases {
+               led-boot = &system;
+               led-failsafe = &system;
+               led-upgrade = &system;
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               system: lan {
+                       label = "tp-link:green:lan";
+                       gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+               };
+
+               wlan5g {
+                       label = "tp-link:green:wlan5g";
+                       gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+                       linux,default-trigger = "phy0tpt";
+               };
+       };
+
+       keys {
+               compatible = "gpio-keys";
+
+               reset {
+                       linux,code = <KEY_RESTART>;
+                       gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+                       debounce-interval = <60>;
+               };
+       };
+
+};
+
+&ref {
+       clock-frequency = <40000000>;
+};
+
+&uart {
+       status = "okay";
+};
+
+&spi {
+       num-cs = <1>;
+
+       status = "okay";
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <25000000>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       uboot: partition@0 {
+                               label = "u-boot";
+                               reg = <0x000000 0x020000>;
+                               read-only;
+                       };
+
+                       partition@20000 {
+                               label = "partition-table";
+                               reg = <0x020000 0x010000>;
+                               read-only;
+                       };
+
+                       info: partition@30000 {
+                               label = "info";
+                               reg = <0x030000 0x010000>;
+                               read-only;
+                       };
+
+                       partition@40000 {
+                               label = "firmware";
+                               reg = <0x040000 0x780000>;
+
+                               compatible = "fixed-partitions";
+                               #address-cells = <1>;
+                               #size-cells = <1>;
+
+                               partition@0 {
+                                       label = "kernel";
+                                       reg = <0x000000 0x1c0000>;
+                               };
+
+                               partition@1c0000 {
+                                       label = "rootfs";
+                                       reg = <0x1c0000 0x5c0000>;
+                               };
+                       };
+
+                       partition@7c0000 {
+                               label = "config";
+                               reg = <0x7c0000 0x030000>;
+                               read-only;
+                       };
+
+                       art: partition@7f0000 {
+                               label = "art";
+                               reg = <0x7f0000 0x010000>;
+                               read-only;
+                       };
+               };
+       };
+};
+
+&wmac {
+       status = "okay";
+
+       mtd-cal-data = <&art 0x1000>;
+       mtd-mac-address = <&info 0x08>;
+};
+
+&eth0 {
+       status = "okay";
+
+       mtd-mac-address = <&info 0x08>;
+
+       phy-mode = "mii";
+       phy-handle = <&swphy4>;
+};
+
+&eth1 {
+       status = "okay";
+       compatible = "syscon", "simple-mfd";
+};

diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk
index 4757df49c6ebf3a9739a99e7a532a2f52e17fc2c..73275ccf355556d6dbb804a15cbaa18e584795a8 100644 (file)
--- a/target/linux/ath79/image/generic-tp-link.mk
+++ b/target/linux/ath79/image/generic-tp-link.mk
@@ -146,6 +146,17 @@ define Device/tplink_cpe210-v3
 endef
 TARGET_DEVICES += tplink_cpe210-v3
 
+define Device/tplink_cpe610-v1
+  $(Device/tplink-safeloader)
+  ATH_SOC := ar9344
+  IMAGE_SIZE := 7680k
+  DEVICE_TITLE := TP-Link CPE610 v1
+  TPLINK_BOARD_ID := CPE610V1
+  LOADER_TYPE := elf
+  KERNEL := kernel-bin | append-dtb | lzma | loader-kernel
+endef
+TARGET_DEVICES += tplink_cpe610-v1
+
 define Device/tplink_archer-d50-v1
   ATH_SOC := qca9531
   DEVICE_TITLE := TP-Link Archer D50 v1

diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c
index b38e37510c7e952be866d3d5393a2613d5447d7a..1a54e92b07cd398d3c1b4e165baf5f129369a3d5 100644 (file)
--- a/tools/firmware-utils/src/tplink-safeloader.c
+++ b/tools/firmware-utils/src/tplink-safeloader.c
@@ -278,6 +278,45 @@ static struct device_info boards[] = {
                .first_sysupgrade_partition = "os-image",
                .last_sysupgrade_partition = "support-list",
        },
+       /** Firmware layout for the CPE610V1 */
+       {
+               .id     = "CPE610V1",
+               .vendor = "CPE610(TP-LINK|UN|N300-5|00000000):1.0\r\n",
+               .support_list =
+                       "SupportList:\r\n"
+                       "CPE610(TP-LINK|EU|N300-5|00000000):1.0\r\n"
+                       "CPE610(TP-LINK|EU|N300-5|45550000):1.0\r\n"
+                       "CPE610(TP-LINK|EU|N300-5|55530000):1.0\r\n"
+                       "CPE610(TP-LINK|UN|N300-5|00000000):1.0\r\n"
+                       "CPE610(TP-LINK|UN|N300-5|45550000):1.0\r\n"
+                       "CPE610(TP-LINK|UN|N300-5|55530000):1.0\r\n"
+                       "CPE610(TP-LINK|US|N300-5|55530000):1.0\r\n"
+                       "CPE610(TP-LINK|UN|N300-5):1.0\r\n"
+                       "CPE610(TP-LINK|EU|N300-5):1.0\r\n"
+                       "CPE610(TP-LINK|US|N300-5):1.0\r\n",
+               .support_trail = '\xff',
+               .soft_ver = NULL,
+
+               .partitions = {
+                       {"fs-uboot", 0x00000, 0x20000},
+                       {"partition-table", 0x20000, 0x02000},
+                       {"default-mac", 0x30000, 0x00020},
+                       {"product-info", 0x31100, 0x00100},
+                       {"signature", 0x32000, 0x00400},
+                       {"os-image", 0x40000, 0x1c0000},
+                       {"file-system", 0x200000, 0x5b0000},
+                       {"soft-version", 0x7b0000, 0x00100},
+                       {"support-list", 0x7b1000, 0x00400},
+                       {"user-config", 0x7c0000, 0x10000},
+                       {"default-config", 0x7d0000, 0x10000},
+                       {"log", 0x7e0000, 0x10000},
+                       {"radio", 0x7f0000, 0x10000},
+                       {NULL, 0, 0}
+               },
+
+               .first_sysupgrade_partition = "os-image",
+               .last_sysupgrade_partition = "support-list",
+       },
 
        {
                .id     = "WBS210",