ramips: add support for ALFA Network R36M-E4G

ALFA Network R36M-E4G is a dual-SIM, N300 Wi-Fi, compact size platform
based on MediaTek MT7620A WiSoC. This product is designed for operation
with 4G modem (can be bought in bundle with Quectel EC25, EG25 or EP06)
but supports also Wi-Fi modules (miniPCIe slot has USB and PCIe buses).

Specification:

- MT7620A (580 MHz)
- 64/128/256 MB of RAM (DDR2)
- 16/32+ MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 2.4 GHz (MT7620A), with ext. LNA (RFFM4227)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses and optional 5 V)
- 2x SIM slot (mini, micro) with detect and switch driven by GPIO
- 2x u.fl antenna connectors (for Wi-Fi)
- 8x LED (7 driven by GPIO)
- 2x button (reset, wifi)
- 2x UART (4-pin/2.54 mm pitch, 10-pin/1.27 mm pitch) headers on PCB
- 1x I2C (4-pin, 1.27 mm pitch) header on PCB
- 1x LED (8-pin, 1.27 mm pitch) header on PCB
- 1x DC jack with lock (12 V)

Other:

- there is a dedicated, 4-pin connector for optional RTC module (Holtek
  HT138x) with 'enable' input, not available at the time of preparing
  support for this board
- miniPCIe slot supports additional 5 V supply on pins 47 and 49 but a
  jumper resistor (R174) is not installed by default
- U-Boot selects default SIM slot, based on value of 'default_sim' env
  variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This will
  work only if both slots are occupied, otherwise U-Boot will always
  select slot with SIM card inside (user can override it later, in
  user-space)
- U-Boot resets the modem, using PERSTn signal, before starting kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
  U-Boot environment variable)

Flash instruction:

You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:

1. Power the device with reset button pressed, the modem LED will start
   blinking slowly and after ~3 seconds, when it starts blinking faster,
   you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

diff --git a/target/linux/ramips/dts/mt7620a_alfa-network_r36m-e4g.dts b/target/linux/ramips/dts/mt7620a_alfa-network_r36m-e4g.dts
new file mode 100644 (file)
index 0000000..ce839f7
--- /dev/null
+++ b/target/linux/ramips/dts/mt7620a_alfa-network_r36m-e4g.dts
@@ -0,0 +1,218 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "mt7620a.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+       compatible = "alfa-network,r36m-e4g", "ralink,mt7620a-soc";
+       model = "ALFA Network R36M-E4G";
+
+       aliases {
+               label-mac-device = &wmac;
+               led-boot = &led_system;
+               led-failsafe = &led_system;
+               led-running = &led_system;
+               led-upgrade = &led_system;
+       };
+
+       chosen {
+               bootargs = "console=ttyS1,115200";
+       };
+
+       gpio-export {
+               compatible = "gpio-export";
+               #size-cells = <0>;
+
+               modem-enable {
+                       gpio-export,name = "modem-enable";
+                       gpio-export,output = <1>;
+                       gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+               };
+
+               modem-rf-enable {
+                       gpio-export,name = "modem-rf-enable";
+                       gpio-export,output = <1>;
+                       gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+               };
+
+               rtc-enable {
+                       gpio-export,name = "rtc-enable";
+                       gpio-export,output = <1>;
+                       gpio-export,direction_may_change = <1>;
+                       gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+               };
+
+               sim-select {
+                       gpio-export,name = "sim-select";
+                       gpio-export,output = <0>;
+                       gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+               };
+
+               sim1-detect {
+                       gpio-export,name = "sim1-detect";
+                       gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+               };
+
+               sim2-detect {
+                       gpio-export,name = "sim2-detect";
+                       gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+               };
+       };
+
+       keys {
+               compatible = "gpio-keys";
+
+               reset {
+                       label = "reset";
+                       gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RESTART>;
+               };
+
+               rfkill {
+                       label = "rfkill";
+                       gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RFKILL>;
+               };
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               4g {
+                       label = "r36m-e4g:orange:4g";
+                       gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+               };
+
+               lan {
+                       label = "r36m-e4g:green:lan";
+                       gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+               };
+
+               led_system: system {
+                       label = "r36m-e4g:green:system";
+                       gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+                       default-state = "keep";
+               };
+
+               sim1 {
+                       label = "r36m-e4g:green:sim1";
+                       gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
+                       default-state = "keep";
+               };
+
+               sim2 {
+                       label = "r36m-e4g:green:sim2";
+                       gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+                       default-state = "keep";
+               };
+
+               wan {
+                       label = "r36m-e4g:green:wan";
+                       gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+               };
+
+               wlan {
+                       label = "r36m-e4g:orange:wlan";
+                       gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+                       linux,default-trigger = "phy0radio";
+               };
+       };
+};
+
+&ehci {
+       status = "okay";
+};
+
+&ethernet {
+       mtd-mac-address = <&factory 0x28>;
+};
+
+&gpio1 {
+       status = "okay";
+};
+
+&gpio2 {
+       status = "okay";
+};
+
+&gpio3 {
+       status = "okay";
+};
+
+&gsw {
+       mediatek,port4 = "ephy";
+};
+
+&i2c {
+       status = "okay";
+};
+
+&ohci {
+       status = "okay";
+};
+
+&pinctrl {
+       state_default: pinctrl0 {
+               gpio {
+                       ralink,group = "ephy", "pcie", "rgmii1", "wled";
+                       ralink,function = "gpio";
+               };
+       };
+};
+
+&spi0 {
+       status = "okay";
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <50000000>;
+               m25p,fast-read;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "u-boot";
+                               reg = <0x0 0x30000>;
+                               read-only;
+                       };
+
+                       partition@30000 {
+                               label = "u-boot-env";
+                               reg = <0x30000 0x1000>;
+                       };
+
+                       partition@31000 {
+                               label = "config";
+                               reg = <0x31000 0xf000>;
+                               read-only;
+                       };
+
+                       factory: partition@40000 {
+                               label = "factory";
+                               reg = <0x40000 0x10000>;
+                               read-only;
+                       };
+
+                       partition@50000 {
+                               compatible = "denx,uimage";
+                               label = "firmware";
+                               reg = <0x50000 0xfb0000>;
+                       };
+               };
+       };
+};
+
+&uart {
+       status = "okay";
+};
+
+&wmac {
+       ralink,mtd-eeprom = <&factory 0>;
+};

diff --git a/target/linux/ramips/image/mt7620.mk b/target/linux/ramips/image/mt7620.mk
index d3de3074b2ec9d2aff4470b9f27a3b034da1e0e2..8aea7f05f101d4c7b2197a36deca11f2391902c7 100644 (file)
--- a/target/linux/ramips/image/mt7620.mk
+++ b/target/linux/ramips/image/mt7620.mk
@@ -35,6 +35,15 @@ define Device/alfa-network_ac1200rm
 endef
 TARGET_DEVICES += alfa-network_ac1200rm
 
+define Device/alfa-network_r36m-e4g
+  MTK_SOC := mt7620a
+  IMAGE_SIZE := 16064k
+  DEVICE_VENDOR := ALFA Network
+  DEVICE_MODEL := R36M-E4G
+  DEVICE_PACKAGES := kmod-i2c-ralink kmod-usb2 kmod-usb-ohci uboot-envtools uqmi
+endef
+TARGET_DEVICES += alfa-network_r36m-e4g
+
 define Device/alfa-network_tube-e4g
   MTK_SOC := mt7620a
   IMAGE_SIZE := 16064k

diff --git a/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds b/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds
index 59f0fe8dabbf4fbadbb73b5b8f33efb2016fb430..d88fdfb043b052034ba883a9a225008f0886441e 100755 (executable)
--- a/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds
@@ -24,6 +24,11 @@ aigale,ai-br100)
 alfa-network,ac1200rm)
        set_wifi_led "$boardname:green:wlan2g" "wlan1"
        ;;
+alfa-network,r36m-e4g)
+       ucidef_set_led_netdev "4g" "4g" "$boardname:orange:4g" "wwan0"
+       ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x8"
+       ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x10"
+       ;;
 alfa-network,tube-e4g)
        ucidef_set_led_netdev "4g" "4g" "$boardname:green:4g" "wwan0"
        ucidef_set_led_netdev "lan" "lan" "$boardname:blue:lan" "eth0"

diff --git a/target/linux/ramips/mt7620/base-files/etc/board.d/02_network b/target/linux/ramips/mt7620/base-files/etc/board.d/02_network
index 1b51f174854bc6e3595d1a4c00a561751d6f9af1..12820f3a366258711fea3ed9577242ed03fc9437 100755 (executable)
--- a/target/linux/ramips/mt7620/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/mt7620/base-files/etc/board.d/02_network
@@ -32,6 +32,11 @@ ramips_setup_interfaces()
                ucidef_add_switch "switch0" \
                        "0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6@eth0"
                ;;
+       alfa-network,r36m-e4g|\
+       zbtlink,zbt-we1026-h-32m)
+               ucidef_add_switch "switch0" \
+                       "3:lan" "4:wan" "6@eth0"
+               ;;
        alfa-network,tube-e4g|\
        buffalo,wmr-300|\
        dlink,dch-m225|\
@@ -190,10 +195,6 @@ ramips_setup_interfaces()
                ucidef_add_switch "switch0" \
                        "0:lan" "6t@eth0"
                ;;
-       zbtlink,zbt-we1026-h-32m)
-               ucidef_add_switch "switch0" \
-                       "3:lan" "4:wan" "6@eth0"
-               ;;
        zbtlink,zbt-we2026)
                ucidef_add_switch "switch0" \
                        "0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "4:wan:5" "6@eth0"
@@ -259,6 +260,11 @@ ramips_setup_macs()
        zbtlink,zbt-wr8305rt)
                wan_mac=$(macaddr_add "$(cat /sys/class/net/eth0/address)" 1)
                ;;
+       alfa-network,r36m-e4g|\
+       zbtlink,zbt-we1026-h-32m)
+               wan_mac=$(mtd_get_mac_binary factory 0x2e)
+               label_mac=$(mtd_get_mac_binary factory 0x4)
+               ;;
        dlink,dch-m225)
                lan_mac=$(mtd_get_mac_ascii factory lanmac)
                ;;
@@ -314,10 +320,6 @@ ramips_setup_macs()
        zbtlink,zbt-we1026-5g-16m)
                label_mac=$(mtd_get_mac_binary factory 0x4)
                ;;
-       zbtlink,zbt-we1026-h-32m)
-               wan_mac=$(mtd_get_mac_binary factory 0x2e)
-               label_mac=$(mtd_get_mac_binary factory 0x4)
-               ;;
        zyxel,keenetic-omni|\
        zyxel,keenetic-omni-ii|\
        zyxel,keenetic-viva)

diff --git a/target/linux/ramips/mt7620/base-files/etc/init.d/bootcount b/target/linux/ramips/mt7620/base-files/etc/init.d/bootcount
index c7b6919926959db8bebe5d08090a5098c4214211..06316e48caec1905b770c80ea1913f0dceada9ef 100755 (executable)
--- a/target/linux/ramips/mt7620/base-files/etc/init.d/bootcount
+++ b/target/linux/ramips/mt7620/base-files/etc/init.d/bootcount
@@ -5,6 +5,7 @@ START=99
 boot() {
        case $(board_name) in
        alfa-network,ac1200rm|\
+       alfa-network,r36m-e4g|\
        alfa-network,tube-e4g)
                [ -n "$(fw_printenv bootcount bootchanged 2>/dev/null)" ] &&\
                        echo -e "bootcount\nbootchanged\n" | /usr/sbin/fw_setenv -s -

diff --git a/target/linux/ramips/mt7620/base-files/lib/upgrade/platform.sh b/target/linux/ramips/mt7620/base-files/lib/upgrade/platform.sh
index aad243c1f9776d6bb0368fc4bc923cb55c0841c7..9f71dc918e50a21d3d14a077a4f4252e39267a68 100755 (executable)
--- a/target/linux/ramips/mt7620/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/mt7620/base-files/lib/upgrade/platform.sh
@@ -17,6 +17,7 @@ platform_do_upgrade() {
 
        case "$board" in
        alfa-network,ac1200rm|\
+       alfa-network,r36m-e4g|\
        alfa-network,tube-e4g)
                [ "$(fw_printenv -n dual_image 2>/dev/null)" = "1" ] &&\
                [ -n "$(find_mtd_part backup)" ] && {